Lamb wave-based structural health monitoring is widely acknowledged as a reliable 11 method for damage identification, classification, localization and quantification. However, due to 12 the complexity of Lamb wave signals, especially after interacting with structural components and 13 defects, interpreting these waves and extracting useful information about the structure's health is 14 still a major challenge. However, deep learning-based strategy offers a great opportunity to address 15 such challenges as the algorithm can operate directly on raw discrete time-domain signals. Unlike 16 traditional methods, which often require careful feature engineering and preprocessing, deep learn-17 ing can automatically extract relevant features from the raw data. This paper proposes an autoen-18 coder based on a bidirectional long short-term memory network with maximal overlap discrete 19 wavelet transform layer to detect the signal anomaly and determine the location of the damage in 20 the composite structure. This approach has the potential to greatly enhance our ability to detect and 21 locate structural damage in composite structures, thereby increasing safety and efficiency.

Bifenthrin is a synthetic pyrethroid insecticide. It is used worldwide against different agricultural pests. Nervous system (NS) is the primary target organ for the pyrethroid group of insecticide which causes hyper excitation. The aim of this study to determine the effects of bifenthrin on the brain of rabbits. The animals were treated for 14 days with three different doses (1/5th, 1/10th and 1/15th of LD50) of bifenthrin. Neurotransmitters and Histopathological alterations were observed at the end of the experiments. Neurochemical parameters were checked 24 hours after the last dose. Significant changes in the level of biogenic amines were observed. The levels of epinephrine (EPN), dopamine (DA), 3, 4 dihydroxyphenylacetic acid (DOPAC) were decreased as compared to controls group with the increase in insecticide. However, norepinephrine (NE) and homovanillic acid (HVA) levels were found to be significantly higher than those of the controls. A significant reduction in the activity of the acetyl cholinesterase enzyme was found in the frontal cortex’s erythrocyte, plasma and brain of rabbit with the increase in administered bifenthrin. The oxidative stress showed significantly decrease in the activity of glutathione peroxidase (GPx), superoxide dismutase (SOD), catalase (CAT) and glutathione S- transferase (GST) with the increase in dose of bifenthrin. Histopathological study of brain tissues showed normal GC (glial cells) and NC (neuronal cells) in the frontal cortex of brain tissue of control groups while the treated groups showed evacuation (odema), elongation of pyramidal nucleus, glial cell damage and brain haemorrhage.

Inflammation is an important biological response to any tissue injury. The immune system responds to any stimulus, such as irritation, damage, or infection, by releasing pro-inflammatory cytokines. Overproduction of pro-inflammatory cytokines, including TNF-α and IL-1b, can lead to several diseases eg.,, cardiovascular diseases, joint disorders, cancer, and allergies. Emerging science suggests that whole grains may lower the markers of inflammation. Whole grains are a significant source of dietary fibres and phenolic acids that have inverse association with the risk of inflammation. The dietary fibres and phenolic acids composition of whole grains is very distinct over different grains. Whole grains (cereals and pseudo-cereals) are rich in both dietary fibres e.g., arabinoxylan, β-glucan and phenolic acids e.g., hydroxycinnamic acids, hydroxybenzoic acids, which are predominantly present in the bran layer. Although the biological mechanisms underlying widely reported association between whole grains consumption and a lower risk diseases are not fully understood. The modulatory effects of whole grains on inflammation also likely to be influenced by several mechanisms, including the effect of dietary fibres and phenolic acids, while some of these effects are direct, others involve gut microbiota, which transform important bioactive substances into more useful metabolites that moderate inflammatory signaling pathway. Thus, the aim of this review is two folded: first is to discuss the types of dietary fibres and phenolic acids commonly found in cereals and pseudo-cereals, and their health benefits observed in animal and human studies. Second, we review existing literature on the linkage between consumption of whole grains and markers of subclinical inflammation, the role of dietary fibres, phenolic acids, and gut microbiota on the anti-inflammatory activity of whole grains intake. Altogether, scientific data on the ant-inflammatory properties of whole grains are encouraging, further researches are needed to cover the gap between the emerging sciences of whole grains dietary fibres, phenolic acids and inflammation.

Drinking water supplies in the developing world often serve as a biosphere for various organisms. Viral gastroenteritis is a neglected area of research in Pakistan, there is no data for the prevalence of enteric viruses in drinking water of the largest city of Karachi. The present study aimed to provide a survey of the existence of enteric viruses: human adenovirus (HAdV), human enteroviruses (hEV), and genotype A rotavirus (GARV) in tap water. Using a simple PCR approach, we detected 20%, 43%, and 23% of HAdV, hEV, and GARV in tap water respectively. We have also shown an overall quality of tap water at the pumping station and consumer tap. Moreover, we assessed the efficiency of small-scale water treatment methods for the removal of viruses.

The versatile one-pot green synthesis of a highly concentrated and stable colloidal dispersion of AgNPs was carried out using the self-assembled tannic acid without using any other hazardous chemicals. Tannic acid (Plant-based polyphenol) was used as a reducing and stabilizing agent for silver nitrate in a mild alkaline condition. The synthesized AgNPs were characterized for their concentration, capping, size distribution, and shape. The experimental results confirmed the successful synthesis of nearly spherical and highly concentrated (2281 ppm) AgNPs, capped with poly-tannic acid (AgNPs-PTA). The average particle size of AgNPs-PTA was found 9.90 ± 1.60 nm. The colloidal dispersion of synthesized nanoparticles was observed stable for more than 15 months in the ambient environment (25 oC, 65 % relative humidity). The synthesized AgNPs-PTA showed an effective antimicrobial activity against Staphylococcus Aureus Escherichia coli. Ag-PTA also exhibited enhanced catalytic properties. It reduces 4-nitrophenol into 4-aminophenol in the presence of NaBH4 with a normalized rate constant (Knor = K/m) of 615.04 mL·s-1·mg-1. Furthermore, AgNPs-PTA were stable for more than 15 months under ambient conditions. The unique core-shell structure and ease of synthesis render the synthesized nanoparticles superior to others, with potential for large-scale applications, especially in the field of catalysis and biomedical.

The Aminofunctional starch/Carboxylated nitrile butadiene rubber (ANS/XNBR) latex films were prepared with control (0), 5, 10, 15, and 20 phr of ANS loadings. The films were subjected to soil burial test for 8 weeks, which recovered every two weeks to quantify the degraded properties. The control (week 0) and biodegraded films were subjected to physical tests (crosslink density, tensile, and tear strength tests) and biodegradation quantification (mass loss retention, and water vapor transmission rates). The optimum physical properties of ANS/XNBR films were subjected to further assessment of its degradation properties which include morphological (optical and scanning electron microscopes (SEM)), Fourier transform infrared (FTIR) analysis, and thermogravimetric analysis (TGA) respectively. Overall, mechanical properties of biodegraded ANS/XNBR latex films decreased as biodegradation period elapses. The biodegradation assessment via water vapor transmission rates and mass loss analyses indicates the high degree of biodegradation rates were observed with higher loading of ANS/XNBR latex films. Morphological analyses via optical microscope shows the transformation of the films surface opacity during biodegradation test. SEM images depicted the microorganism remains on the film surfaces. For FTIR analysis, the most significant changes in the spectras of the films appeared in the region of 790–3000 cm⁻¹. TGA thermograph shows the thermal retention of the materials decreased, as the biodegradation period elapses for optimum ANS/XNBR latex films. From the results obtained, ANS/XNBR latex films shows optimum degradation and mechanical properties at 10 phr filler loading.

Increasing genetic diversity in crop plants has been used for chemical mutagenesis. Through the application of various mutagenic agents, over 430 new varieties have been derived as rice mutants (Oryza sativa L.) Chemical mutagens such as ethyl methane sulphonate (EMS), diepoxybutane derivative (DEB), sodium azide, and gamma ray, x-ray, and quick neutron irradiation have been commonly used to induce a large number of functional variations in rice and others crops. Among chemical mutagens, ethyl methane sulfonate (EMS) is the alkylating agent most widely used in plants because it induces nucleotide substitutions to be extremely frequent, as detected in various genomes. In this study, seeds of potential genotype of the popular variety, (Oryza sativa L. Super Basmati variety) were treated with EMS at concentrations of 0.25%, 0.50%, 0.75%, 1% and 1.5%. Various measurements on the M1 generation determined EMS sensitivity. As concentration of applied EMS increased, will decrease in germination, shoot length, root length, plant height, productive tillers, Panicle Length, Total Spikelet, sterile spikelet and fertility under field conditions were observed in M1 generation as compared to the non-treatment control. Emergence, shoot length, root length, plant height, productive tillers, Panicle Length, Total Spikelet, sterile spikelet and fertility also decreased with increases in EMS mutagenesis in an approximately linear fashion. The LD₅₀ values were observed based on growth reduction of seedlings after EMS treatment with 0.25% and 0.50% on the rice variety (Oryza sativa L. spp.).

This comprehensive article explores Massive MIMO (M-MIMO) design and its associated concepts, focusing on the seamless integration requirements for Beyond 5G (B5G) and 6G networks. Addressing critical aspects such as RF chain reduction, pilot contamination, Cell-Free MIMO, and security considerations, the article delves into the intricacies of M-MIMO in the evolving landscape of B5G. Moreover, the emerging MIMO concepts in this article include AI-enabled M-MIMO three-dimensional beamforming, reconfigurable intelligent surfaces, visible light communication, and THz spectrum utilization. This review highlights challenges and open research issues, including Narrow Aperture Antenna Nodes, Plasmonic Antenna Arrays, Integrated Sensing with M-MIMO, and the application of Federated Learning in M-MIMO systems. By examining these cutting-edge developments, the article aims to contribute to advancing knowledge in the field and inspire future research directions in the exciting realm of B5G and 6G networks.

Globally, rice is utilized as staple food, belongs to the family Poaceae. From the past few decades under variable climate conditions, it greatly affected by the bacterial leaf blight (BLB) disease caused by a bacterium Xanthomonas oryzae pv. oryzae (Xoo). Scientists studied causes of the disease and found more than 61 isolates of Xoo. About 39 Xa genes were noted that cause race specifically resistance either individually or in pairs against Xoo. The canvas on the characterization of these genes is still unrevealed. In this study, amino acid sequences of Xa15, Xa19, Xa20 and Xa21 were mined and used for motif-domain identification, characterization, and comparative analysis. It includes screening of physical and chemical characteristics, sequence comparison to find sequence similarity between them and their phylogenetic comparison with other Xa genes and other species based upon LRR and S_TKc domains to find evolutionary relationship among them. The comparison-based modeling was performed and assessed by different tools to gain better understanding and structural evaluation. The results showed identified domains are specific in function, each domain involved in resistance against biotic and abiotic stresses through regulating different cellular processes. This study also revealed high similarity (>98% sequence identity) between these genes and encode a similar leucine-rich repeat receptor kinase like protein. It will optimize the breeding programs as it will be useful for the selection of effective genes to produce resistance in rice varieties against the specific strains of Xoo that will be more effective against BLB than the other Xa genes.

COVID-19 outbreak started in the Chinese city of Wuhan and spread around the globe in months due to its high contagious level. Hence, this disease posed a great challenge to researchers and mathematicians. Numerous mathematical models have been suggested to visualize the spreading speed and trends of this pandemic. In this paper, a comparison of a widely established and accepted method, the Susceptible-Exposed-Infected-Quarantined-Recovered-Death-Insusceptible (SEIQRDP) model with a newly-proposed fractional-order SEIQRDP is studied. Densely populated Countries of Asia (Pakistan, India, and Bangladesh) have been chosen as data sets and both algorithms have been applied to their data. The same comparison technique has also been used on the data of two polar countries, New Zealand and Russia, that validated our findings. Error comparison of both algorithms has been recorded in a tabulated form which shows multi-fold erroneous trends over WHO data of selected countries.

5G low-earth orbit satellite communications offer enhanced wireless coverage beyond the reach of 5G terrestrial networks, with important implications, particularly for automated and connected vehicles. Such wireless automotive mass-market applications demand well-designed compact user equipment antenna terminals offering non-terrestrial jointly with terrestrial communications. The antenna should be low-profile, conformal, and meet specific parameter values for gain and operational frequency bandwidth, tailored to the intended applications, in line with the aesthetic design requirements of passenger cars. This work presents an original concept for a dual-band nested circularly polarized automotive user terminal that operates at the S-band frequencies around 3.5 GHz and Ka-band frequencies around 28 GHz, namely within the 5G new-radio bands n78 and n257, respectively. The proposed terminal is designed to be integrated into the plastic components of a passenger vehicle. The arrays consist of 2×2 aperture-coupled corner-truncated microstrip slot patch antenna elements for the n78 band and of 4×4 single-layer edge-truncated microstrip circular slot patch antenna elements for the n257 band. The embedded arrays offer, across the two bands, respectively 9.9 and 13.7 dBi measured realized gain and 3-dB axial ratio bandwidths of 100 and 1500 MHz for the n78 and n257 bands along the broadside direction. Detailed link budget calculations anticipate uplink data rates of 21 and 6 Mbit/s, respectively, deeming it suitable for various automotive mobility and internet-of-things applications.

During December 2019, a novel coronavirus named SARS-CoV-2 has emerged in Wuhan, China. The human to human transmission of this virus has also been established. The virus has so far infected more than 2 million people and spread over 200 countries. The World Health Organization (WHO) has declared COVID-19 a global health emergency due to its spread well beyond China. It has been established that this virus originates from bats and uses an intermediate host for transfer to humans. The knowledge about the intermediate host is important to find the virus shuttle mechanism to stop future outbreaks. For this, the genetic and structural analysis of coronaviruses spike proteins was performed using a computer-assisted approach.To conduct the In silico analysis, 43 sequences of spike protein belong to different species were retrieved from the NCBI nucleotide database. Pairwise and multiple sequence alignments were performed to check the similarities and differences of the retrieved sequences. Moreover, to highlight relationships among different species, phylogenetics analysis was performed using the MEGA software tool. In the end, protein structure alignment (superimposition) was performed against the reference structure by UCSF Chimera software. The results highlighted that the maximum similarity of human protein was found against Bat and Pangolinsequences. Moreover, among Bat and Pangolin, the highest similarity was found against pangolin based on phylogenetics analysis. These results suggest that SARS-CoV-2 transfers from bats to humans through pangolins.

Objective: The private healthcare providers (PHCP) are believed to improve access to healthcare services in Public-Private Mix (PPM) projects, as they are considered first point of contact for healthcare. The purpose of this study was to know the satisfaction level of TB patients. Design: A questionnaire-based, cross-sectional study was carried out during November and December 2017 for 572 under-treatment patients registered with PHCPs in the PPM project. Lot quality assurance sampling technique was used to randomly select 19 districts from sample frame of 75 districts. In each selected district, data collector retrieved TB register of 8 months (Jan – Aug 2017) and systematically selected patients by fixed periodic interval. SPSS (version 24.0) was used to analyze the data. Results: Study included 53% (n=301) of males and 47% (n=271) of females, with mean age of 38 years (SD, ±18). Almost half of the participants were illiterate (51%, n=289) and 64% (n=365) were non-earning members of the family. In practice, most of the participants visit private providers (71%, n=407), including private hospital/clinic (44%) and traditional practitioners (27%; n=153). 55% of participants visited the current doctor because of clinic’s proximity to residence. 82% of the participants (n=469) were satisfied with the TB care services and 85% (n=488) said that they would recommend this clinic to others. Conclusion: PHCPs are preferred providers for individuals, which is consistent with findings of other studies. Though they are satisfied with TB care and services, interventions should be introduced to reduce the financial burden on the patient. Partnering PHCP is a way forward to ensure universal health coverage, health system strengthening and better health outcomes of the population.

Pseudomonas aeruginosa is a critical healthcare challenge due to its ability to cause persistent infections and the acquisition of antibiotic resistance mechanisms. Lack of preventive vaccines and rampant drug resistance phenomenon has rendered patients vulnerable. As new antimicrobials are in the preclinical stages of development, mining for the unexploited drug targets is also crucial. Here, we designed a chimeric vaccine against P. aeruginosa using a subtractive proteomics approach and identified nine unique enzymes as novel drug targets in PAO1 proteome. A total of five unique proteins were selected as potential vaccine candidates based on essentiality, extracellular localization, virulence, antigenicity, pathway association, protein-protein interaction analysis, hydrophilicity, and low molecular weight. These include two outer membrane porins OprF (P13794) and OprD (P32722), a protein activator precursor pra (G3XDA9), a probable outer membrane protein precursor PA1288 (Q9I456), and a conserved hypothetical protein PA4874 (Q9HUT9). These proteins were further analyzed using a reverse vaccinology approach to identify immunogenic and antigenic T cell and B cell epitopes. The best scoring epitopes qualifying for all set criteria were then further subjected to the construction of a polypeptide multi-epitope vaccine construct with cholera toxin B (CtxB) subunit as an adjuvant. The identified drug targets qualifying the screening criteria were: UDP-2-acetamido-2-deoxy-d-glucuronic acid 3-dehydrogenase WbpB (G3XD23), aspartate semialdehyde dehydrogenase (Q51344), 2-amino-4-hydroxy-6-hydroxymethyldihydropteridine pyrophosphokinase (Q9HV71), 3-deoxy-D-manno-octulosonic-acid transferase (Q9HUH7), glycyl-tRNA synthetase alpha chain (Q9I7B7), riboflavin kinase/FAD synthase (Q9HVM3), aconitate hydratase 2 (Q9I2V5), probable glycosyltransferase WbpH (G3XD85) and UDP-3-O-[3-hydroxylauroyl] glucosamine N-acyltransferase (Q9HXY6). For druggability and pocketome analysis crystal and homology structures of these proteins were retrieved and developed. A sequence-based search was performed in different databases (ChEMBL, Drug Bank, PubChem and Pseudomonas database) for the availability of reported ligands and tested drugs for the screened targets. These predicted targets may provide a basis for the development of reliable antibacterial preventive and therapeutic options against P. aeruginosa.

Compressive residual stresses in thin films can inhibit crack propagation under normal or sliding contact loading, with associated enhancement of the coating apparent toughness, load bearing capacity and wear resistance. This study investigates the influence of residual stress distributions on the thin film/substrate adhesion using a nanoindenter coupled with scanning electron microscope (SEM) investigations of indentation induced failure modes. Reactive and un-reactive magnetron sputtering with ion plating was used to coat a (100) silicon substrate with aluminum nitride (AlN) with and without an aluminum (Al) adhesion layer. The presence of an Al bond layer gives additional interfacial tensile stress because of the difference in thermal expansion coefficient. Additionally, a different magnitude of residual stresses in the AlN coating was achieved by changing the applied bias voltage onto the substrate. Wafer curvature method and incremental focused ion beam (FIB) milling, combined with high-resolution in situ scanning electron microscopy (SEM) imaging and full field strain analysis by digital image correlation (DIC), were used to measure the average and in-depth stress residual stress distribution in the produced coatings. The adhesion energy was then quantified by using a nanoindentation based model. Results demonstrate that the additional tensile residual stress in the aluminum adhesion layer decrease significantly the coating adhesion, even in presence of a higher compressive stress state in the AlN top-layer. Therefore, the coatings without Al-layer showed better adhesion because of a more homogeneous compressive residual stress in comparison with the coating having Al layer, even though both groups of coatings are produced under same bias voltage. Results are discussed, and some general suggestions are made on the correlation between coating/substrate property combination and the adhesion energy of multilayer stacks. The results suggested that Al bond-layer and inhomogeneous residual stresses affected the adhesion of AlN negatively to a substrate like silicon.

Establishment of protected areas (PAs) is one of the key global conservation strategies that currently cover approximately 15% of the earth’s land surface. Globally, PA networks are designed to curb the growing anthropogenic pressures in areas with high biological diversity. Despite the importance of PAs in conserving the vanishing biodiversity and unique habitats, many of them are in critical condition due to poor governance thus functioning below the expected level. Moreover, in many developing countries, the PA coverage is below the global standard. Recognizing their contemporary role in conservation, governments have recently agreed to expand the global PA coverage to 17% by the year 2020 (Aichi target 11). This book with eight chapters from different regions of the world provides an overview of the PAs governance, institutional mechanisms, conservation benefits, limitations and challenges associated with their respective policy discourse, integrated management, and functional attributes. Protected areas expect to to play an important role in the long rn in conservation and protection of biodiversity and ecosystems particularly in countries where population pressure and habitat loss are high. Regular intervention, political commitment, and effective governance are essential for the sustainability of PAs across the world. Here, we also attempted to shed some light on future development clues for the sustainable management and monitoring of PAs worldwide.

Spectrometers have a wide range of applications ranging from optical to non-optical spectroscopy. The need for compact, portable, and user-friendly spectrometers has been the pivot of attention from small laboratories to the industrial scale. Here, the Czerny Turner configuration-based optical spectrometer simulation design is carried out using ZEMAX OpticStudio. A compact and low-cost optical spectrometer in the visible range has been developed by using diffraction grating as a dispersive element and USB-type WebCAM CCD (Charge-coupled device) as a detector instead of an expensive commercial diffraction grating and detector. Using National Instruments LabVIEW, data acquisition, processing, and displaying techniques are made possible. We have employed different virtual images in LabVIEW programs to collect the pixel-to-pixel information and wavelength-intensity information from the image captured using the WebCAM CCD. Finally, we have shown that the OpticStudio-based spectrometer and experimental measurements of the developed spectrometer are in good agreement.

Nowadays, more than 180 million people believe that the Holy Qur'an was sent by the Almighty Allah through Prophet Muhammad in 610-632 A.D in Mecca and Medina. However, the word Mecca (Q: 48:24) is mentioned only once in the entire Holy Qur'an, which is not related to the birth of the Prophet or any worship. Conventional Islam is mostly based on the hearsay of some Islamic narrators published in the eighth and ninth centuries. To think deeply and conduct research on the verses of the Holy Quran has been mentioned (special urge) directly and indirectly by this Holy Scripture itself many times but it would not be wrong to say that there is no scholarship on the verses of the Quran based on the research method described in the Holy Quran until the present century. Therefore, this paper has been dared to carry out by combining the methods of research followed in the Holy Quran and the academically accepted research methodology. The analysis shows that the results of almost fourteen hundred years of mythological history of conventional Islamic narrators are opposites. First of all, the proper name of the Prophet revealed by the Holy Quran is Ahmed, but Muhammad is an adjective and there are many such names. Secondly, this prophet was not born in Mecca, KSA, nor in 570/571 A.D, but in the Beqaa Valley of Lebanon, between the third and fourth centuries. Thirdly, the Muslim Hajj (pilgrimage) of Mecca is celebrated entirely according to the Lahwal Hadith (idle tales) (Q: 31:6) in the language of the Holy Quran. Originally the place designated for pilgrimage was in the Beqaa Valley, Lebanon. This article will have a double influence on the Muslim world, that is, Islamic scholars will think again deeply and research new ways of scholarship of the Holy Quran, instead of based on the hearsay of idle tales (Lahwal Hadith). On the contrary, those who are stubborn Islamic narrators, since they have already rejected the Holy Quran, will not hesitate to violently attack the researchers and they will not be positively motivated by this paper. This article specifically urges Islamic scholars to conduct in-depth studies on the most important issues of Islam using the Holy Quranic research method.

A low-cost medium power carbon dioxide (CO₂) laser system is designed, constructed, and characterized to produce coherent, monochromatic laser radiation in the Infrared region. The laser cavity is simulated and designed by using ZEMAX optic studio. A switch-mode high tension pump source is designed and constructed using a flyback transformer and simulated using NI Multisim to study the voltage behavior at different node points. A prototype cooling system/chiller is designed and built using the Thermo-Electric Coolers (TEC) to remove the excess heat produced during laser action. Various parameters, like pumping mechanism, chiller stability, efficiency, output power, and current at different applied voltages, are studied. The chiller efficiency at different output powers of the laser is analyzed, which clearly shows that the chiller's cooling rate is good enough to compensate for the heat generated by the laser system. The center wavelength of the carbon dioxide laser is 10.6μm with FWHM of 1.2nm simulated in the ZEMAX optic studio. The output beam penetration through salt rock (NaCl), wood, and acrylic sheet at various output powers is analyzed to measure the penetration depth rate of the CO₂ laser.

In this work, the ternary titanium, copper and silver (Ti-Cu-Ag) system is investigated as a potential candidate for the production of mechanically robust biomedical thin films. The coatings are produced by physical vapor deposition-magnetron sputtering (MS-PVD). The composite thin films are deposited on a silicon (100) substrate. The ratio between Ti and Cu was approximately kept one, with the variation of the Ag content between 10 and 35 at.%, while the power on the targets is changed during each deposition to get the desired Ag content. Thin film characterization is performed by x-ray diffraction (XRD), nanoindentation (modulus and hardness) and Atomic force microscopy to determine the surface topography. The residual stresses are measured by focused ion beam and digital image correlation method (FIB-DIC). The produced Ti-Cu-Ag thin films appear to be smooth, uniformly thick and exhibit amorphous structure for the Ag contents lower than 25 at.%, with a transition to partially crystalline structure for higher Ag concentrations. The Ti-Cu control film shows higher values of 124.5 GPa and 7.85 GPa for modulus and hardness respectively. There is a clear trend of continuous decrease in the modulus and hardness with the increase of Ag content, as lowest value of 105.5 GPa and 6 GPa for 35 at.% Ag containing thin films. In particular, a transition from the compressive (-36.5 MPa) to tensile residual stresses between 229 MPa and 288 MPa are observed with an increasing Ag content. The obtained results suggest that the Ag concentration should not exceed 25 at.%, in order to avoid an excessive reduction of the modulus and hardness with maintaining (at the same time) the potential for an increase of the antibacterial properties. In summary, Ti-Cu-Ag thin films shows characteristic mechanical properties that can be used to improve the properties of biomedical implants such as Ti-alloys and stainless steel.

Good governance in natural resource management (NRM) is one of the most challenging issues in developing countries that often inappropriately embedded in national policies and political agendas. It is, in fact, even more important for countries like Bangladesh with exceptionally high pressure and dependence on its natural resources for sustaining rural livelihoods. Globally, nowadays, good governance is considered as one of the key factor for achieving the goal of sustainable development and biodiversity conservation. Bangladesh, of late has responded to that global zeal by involving local communities in the management of country’s declining forest and other natural resources. The colonial legacy of the forestry sector of Bangladesh was planned and, managed as interim projects through donors’ prescriptions. Thus, institutions, management processes and conservation outcomes were problematic. The conventional approach adopted by colonial and post-colonial regimes for forest management also proved to be inefficient due to its top-down management system. The absolute dependency on donor support, and their prescription sometimes worsened the situation both ecologically and socially. Global, regional and local trends supported the need for a different dimension in the governance paradigms. The introduction of a pluralistic approach, known as co-management in protected areas (PAs) is an example of an attempt whereby shared governance mechanism are implemented to attain the desired goals of conservation that will also address the livelihoods and aspirations of communities living in and around PAs of the country. However, in designing future forest and PA regimes the concern of the external aid support and attached conditions remain a reality that needs to be addressed. Adequate attention should be given to our vanishing biodiversity, culture and community livelihoods through devising an appropriate governance mechanism recognizing and supporting local rights, access and participation in the environmental management. It is now time to mainstream the adhoc nature of governance according to our national conservation strategy and policy frameworks in order to achieve the goals and objectives of the Bangladesh NRM sector addressing the human and community right of people in the specific context of forest protected areas management.

This analysis examines the wide range of occupational and environmental health risks that affect people in diverse settings. This article emphasizes the importance of conducting exposure and risk assessments to safeguard public health by analyzing various hazards, including arsenic, oil accidents, lead, welding fumes, and mycotoxins. Various methodologies are utilized in these research articles to conduct the study, emphasizing hazard identification, exposure assessment, and risk characterization. The results uncover harmful substances, vulnerable demographics, and occupational duties linked to increased hazards. The report suggests various mitigation strategies, such as targeted interventions, enhanced community efforts, and improved exposure estimates. Notwithstanding the constraints identified in certain studies, the review emphasizes the necessity for continuous investigation to improve assessments of exposure, comprehend the cumulative effects, and examine the wider societal consequences. The significance of sector-specific risk assessments, protective measures, and ongoing monitoring is underscored to ensure mental and physical health protection.

Increased construction activities in Australia have led to the generation of a massive volume of construction and demolition (C&D) waste annually. Management of this volume of waste requires an effective waste framework. The literature reported that the current Australian waste framework does not meet expectations and needs immediate improvements. This study was therefore conducted to seek the key C&D stakeholders' opinion about various issues identified in this waste stream. The specific objectives of this study are identification of the main barriers to effective C&D waste management, the impact of current regulations and opportunities to enhance the current C&D waste management system. A survey was conducted in 2019 to capture the stakeholders' perception. 132 participants from various industries and government agencies based in various Australian jurisdictions took part in the survey. The key results showed that the main barriers towards an effective management system are "overregulation, tough acceptance criteria, and increased testing requirements", "lack of local market" and "culture, poor education and low acceptance". Furthermore, a low number of participants indicated that the current legislation encourages waste recovery activities. The main areas of improvements included "providing a guideline that determines the accepted level of contamination for reusing C&D waste”, "preparation of guidelines on requirements of using recycled C&D materials in different industries" and "setting target for reduction, reusing, and recycling C&D waste". The results can inform policy development and be used as evidence for a broader discussion to solve lasting issues in C&D waste management.

The videofluorographic study is indicated for diseases potentially causing dysphagia and aspiration, such as gastrointestinal reflux disease, cancers of the oropharynx and esophagus, and certain neurologic diseases needing swallowing assessment. The study is designed to survey the anatomy and physiology of swallowing to diagnose any swallowing impairment and is standardized using scales such as the Modified Barium Swallow Impairment Profile (MBSImP). The procedure requires the patient to swallow a barium contrasted bolus which helps to visualize and obtain a real-time result. There are certain complications of the procedure including radiation exposure which requires necessary safety protocols to be followed.

Microplastic contamination, defined as plastic particles less than 5 mm in size, has become a major global environmental concern. This study synthesizes findings from carefully chosen studies undertaken in a variety of geographical areas and ecosystems, offering light on the multifaceted issues posed by microplastic pollution. These articles show the global prevalence of microplastics in both land and marine ecosystems. Seasonal fluctuations in microplastic abundance highlight the cyclical nature of this pollution, with larger amounts being reported during the summer months. Tourism, industrialization, and urbanization have all been highlighted as significant contributors to microplastic contamination, stressing the impact of man-made influences. Wastewater treatment plants (WWTPs) have been identified as hotspots for microplastic release into aquatic habitats, emphasizing the need for enhanced treatment procedures. Because microplastics can build up in the food chain, it underlines the possible health problems connected with microplastic pollution for both aquatic creatures and human consumers. Longitudinal studies, geographical variety, in-depth health and ecological impact evaluations, standardization, and effective mitigation methods should be prioritized in future studies. To address this worldwide issue, interdisciplinary collaboration among scientists, health professionals, politicians, and industrial stakeholders is required.

The important topic of climate change is discussed in this article, with a focus on the historical background and present effects. It draws attention to the differences between climate change and global warming and attributes the faster pace of climate change to human activity, specifically the release of greenhouse gases into the atmosphere. Agricultural practices, deforestation, and the combustion of fossil fuels are examined in conjunction with natural contributors like volcanic emissions. There is discussion of the far-reaching effects of climate change, such as increased temperatures, rising sea levels, harsh weather, and effects on water supplies. The article emphasizes how crucial it is to mitigate and adapt to the effects of climate change by putting in place climate-resilient infrastructure, switching to renewable energy sources, and lowering greenhouse gas emissions. While recognizing the difficulties involved, it examines several approaches, including nuclear energy, wind power, carbon capture and storage, and green building techniques. To successfully address the global challenge of climate change, the conclusion emphasizes the urgent need for joint efforts by scientists, environmentalists, communities, and governments.

Lump sum contracts are specific contracts used in the construction industry to give owners financial certainty and decrease risk while incentivizing contractors to finish projects on schedule and within budget. This article discusses the usage of lump sum contracts in construction projects, covering the types of projects appropriate for lump sum contracts, critical considerations for entering a lump sum contract, and the tender and preliminary expenses involved. The article also covers lump sum contracts' benefits and drawbacks and how owners and contractors allocate risk. Finally, the difficulties of implementing lump sum contracts, such as potential disagreements over scope changes and quality issues, are investigated. In general, lump sum contracts can be a valuable tool for managing construction projects, but their execution necessitates careful planning and collaboration to ensure successful completion.

Mercury (Hg (II)) contamination is indefatigable global hazard which causes severe permanent damages to human health. Extensive research has been carried out to produce mercury adsorbents however they are still facing certain challenges limiting their upscaling. Herein we reported the synthesis of novel amine impregnated inverse vulcanized copolymer for effective mercury removal. Poly(S-MA) was prepared using sulfur and methacrylic acid employing inverse vulcanization method following by functionalization. The polyethylenime (PEI) was impregnated on poly(S-MA) to increase the adsorption active sites. The developed adsorbent was then characterized using Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). FTIR confirmed formation of copolymer and successful impregnation of PEI and SEM revealed composite porous morphology of the copolymer. Amine impregnated copolymer (amine@poly(S-MA)) outperformed poly(S-MA) in mercury as it showed 20 % superior performance with 44.7 mg/g maximum adsorption capacity. The adsorption data best fits the pseudo second order which indicates that the chemisorption is most influential mechanism in this case indicating the involvement of NH2 in mercury removal. The adsorption is mainly monolayer on homogenous surface as indicated by 0.76 value of Redlich-Peterson exponent (g) which describes the adsorption nature advent from R2 value of 0.99.

In this paper, the integrated performance of a modular biomass boiler with an existing industrial Rankine steam heat and power cycle and a supplementary supercritical-CO2 (sCO2) Brayton cycle is analyzed. The aim is to leverage the high efficiency supplementary sCO2 cycle to increase net generation and energy efficiency from the existing biomass boiler. Two sCO2 heater configurations situated within the flue gas flow path are investigated, namely a single convective-dominant heater, and a dual heater configuration with a radiative and a convective heater. A quasi-steady-state 1D model was developed to simulate the integrated cycle, including detailed component characteristics for the Rankine and Brayton cycles. The model solves the mass, energy, momentum, and species balance equations. The system is analyzed for three cases: (i) the existing Rankine cycle without the sCO2 integration, (ii) with the single convective-dominant sCO2 heater configuration, and (iii) the dual sCO2 heater configuration. The results show the required rate of overfiring for the sCO2 configurations, with a 15.3% increase in fuel flowrate resulting in an additional 21.2% in net power output. The model quantifies the impact of the sCO2 heaters, with reduced heat uptakes for downstream boiler heat exchangers. Furnace water wall heat uptake increased due to overfiring, offsetting the reduced heat uptakes at downstream evaporative heat exchangers. The dual configuration has more impact on Rankine cycle operation due to the radiative sCO2 heater placement in front of the second superheater, absorbing some of the direct radiation from the furnace.

The Agile Building Adaptation (AgiBuild) framework is the adoption and adaptation of the large-scale agile framework for building adaptation projects. The agile methodology is proven to drive innovation by focusing on adaptation to change and user centricity. Similarly, the authors envision that the AgiBuild framework can fundamentally change the way that buildings are re-designed, refurbished, and operated. The AgiBuild framework is developed from the need of the building adaptation industry to manage uncertainties, overcome communication barriers, and improve innovation. In this study, a literature review of Agile and its impact on building adaptation projects is undertaken. Based on this systematic literature review, this paper defines the AgiBuilt framework and provides its benefits and barriers to implementation. A key finding of the literature review is that leadership influence, and adequate training form the key foundation for the implementation of the AgiBuild Framework. In defining the AgiBuild framework, the paper describes its components and how its implementation is likely to proceed. The authors propose that by adopting the AgiBuild framework, the industry can transform itself into a highly innovative and user-centred industry to improve productivity and performance of the construction industry..

Tuberculosis (TB) associated stigma is well-documented phenomenon that may contribute to sub-optimal TB care in Pakistan. The objective of study was to assess TB related knowledge and perceived stigma among community members. This was cross-sectional survey using convenience sample of 183 individuals recruited between October and December 2017. A validated stigma measurement tool developed by Van Rie et al. was adapted. Data was analyzed using SPSS version 20.0. 183 individuals (73% males; n = 134) participated in survey. Eighty-seven percent were aware that TB is curable disease (n = 159) and 91% thought that it could be transmitted by coughing (n = 167). However, respondents also thought that TB was spread through contaminated food (73%; n = 134), sharing meals (55%; n = 100), sharing utensils (53%; n = 96) and by having sexual intercourse with a TB patient (51%; n = 93). Fifty-seven percent (n = 104) associated TB with high levels of stigma. Persons who had less than six years of education (crude OR = 1.2; 95% CI: 0.89, 1.72) and lacked knowledge that TB is curable (crude OR = 3.42; 95% CI: 1.20, 9.70) were more likely to associate TB with stigma. In addition, females (crude OR = 1.33; 95% CI: 0.87, 2.04) and those who were unemployed (crude OR = 1.06; 95% CI: 0.65, 1.74) were also more likely to associate TB with stigma. We found an association between lack of knowledge about TB and perceived stigma. This highlights need for improved education and awareness about TB.

(1) Background: Pedestrian injuries (PIs) represent a significant proportion of road traffic injuries. We aimed at investigating the incidence and mortality of PIs in different age groups and Socio-demographic Index (SDI) categories between 1990 and 2017. (2) Method: Estimates of age-standardized incidence and mortality along with trends of PIs by SDI levels were obtained from the Global Burden of Disease from 1990 to 2017. We also calculated forecasts until 2040. (3) Results: Globally, PIs incidence increased by 3.31% (–9.94 to 16.56) in 2017 compared to 1990. Men have a higher incidence of PIs than women. Forecasted incidence was 132.02 (127.37 to 136.66) per 100,000 population in 2020, 101.52 (65.99 to 137.05) in 2030 and reduced further to 71.02 (10.62 to 152.65) by 2040. Globally across all SDI categories, there was a decreasing trend in mortality due to PIs with the global estimated percentage reduction of 37.12% (–45.19 to –29.04). (4) Conclusions: The results show that PIs are still a burden for all SDI categories despite some variation. Although incidence and mortality are expected to decrease globally, some SDI categories may require particular attention in addition to specific vulnerable age groups. Further studies addressing incidence and mortality patterns in vulnerable SDI categories are needed.

Conventional diagnostic techniques are based on utilization of analyte sampling, sensing and signalling on separate platforms for detection purposes, that must be evaded and integrated to a single step procedure in point of care (POC) testing devices. Therefore, the trend has been shifted towards utilization of microfluidic platforms for detection of analytes in biochemical, clinical and food technology due to its being expeditious. Microfluidic systems moulded with polymer substances or glass offer specific and sensitive detection of infectious and non-infectious diseases by providing innumerable benefits including less cost, good biological affinity, strong capillary action and simple process of fabrication. In the case of nucleic acid-based nanosensors, there are some challenges that need to be addressed such as cellular lysis, isolation and amplification of nucleic acid required to be accomplished prior to its detection. To avoid utilization of laborious steps for executing these steps, advances have been deployed in this perspective for on-chip sample preparation, amplification and detection which not only improves sensitivity and selectivity but also saves time and resources. This review emphasizes the significance of microfluidic technology for nucleic acid detection of infectious and non-infectious diseases. The implementation of isothermal amplification in concomitance with lateral flow assay greatly increases the binding efficiency of nanoparticles and biomolecules, improves limit of detection and sensitivity. Most importantly deployment of paper-based material made of cellulose reduces the overall cost. Microfluidic technology in nucleic acid testing has been discussed by explicating its applications in different fields. This review concludes with the prospects and proposes future directions in microfluidic based methods in disease diagnosis.

We studied the influence of lava meal, zeolite and top layer of sandy soil as bedding additives on gaseous C and N losses from a sloping-floor barn of naturally ventilated animal housing. We selected four barn units where eight young bulls’ group was reared in each barn. Chopped straw of wheat and barley applied daily at the rate of 5 kg per livestock unit (LU) in bedding areas where one LU consisted of 500 kg body mass of live bulls. Zeolite, lava meal and sandy soil (18% clay + silt) applied in barn at the rate of 10, 20 and 30% of straw dose, respectively. Static flux chamber was used to measure gases emissions from the barn unit and mass balance calculation was used to calculate straw manure total N (TN) losses during housing phase. On an average, all bedding additives decreased 85% of the NH₃ emission compared to control; however, they did not influence CH₄ emission. Zeolite decreased CO₂ (35%) and N₂O (37%) emission rates. Subsequently, lava meal, sandy soil and zeolite decreased 23, 37, and 50% of TN losses from barn manure, respectively. Overall, measured N emissions through NH₃-N and N₂O-N from the barns was 11% of calculated TN losses while remainder 89% was most probably attributed to di-nitrogen (N₂), a harmless gas. Hence, in straw-based cattle housings, zeolite could be a promising additive for reduction of CO₂, N₂O and NH₃ emissions and sandy soil can be considered as cheap and readily available resource for reducing NH₃ emission.

N6-methyladenosine (m6A) is an RNA modification wherein N6-position of adenosine is methylated. It is one of the most prevalent internal modifications on RNA and regulates various aspects of RNA metabolism. M6A is deposited by m6A methyltransferases, removed by m6A demethylases and recognized by reader proteins, which modulate splicing, export, translation and stability of the modified mRNA. Recently evidence suggests that various classes of non-coding RNAs (ncRNAs) including microRNAs (miRNAs), circular RNAs (circRNAs), and long con-coding RNAs (lncRNAs) are also targeted by this modification. Depending on the ncRNA species, m6A may affect processing, stability, or localization of these molecules. The m6A modified ncRNAs are implicated in a number of diseases including cancer. In this review, I summarize the role of m6A modification in the regulation and function of ncRNAs in tumor development. Moreover, the potential applications in cancer prognosis and therapeutics is discussed.

The spectral properties of a one-dimensional photonic crystal bounded by a resonant absorbing nanocomposite layer with the near-zero permittivity have been studied. The problem of calculating the transmittance, reflectance, and absorptance spectra of such structures at the normal and oblique incidence of light has been solved. It is shown that, depending on the permittivity sign near zero, the nanocomposite is characterized by either metallic or dielectric properties. For the first time, the possibility of simultaneous formation of the Tamm plasmon polariton at the photonic crystal/metallic nanocomposite interface and the localized state similar to the defect mode with the field intensity maximum inside the dielectric nanocomposite layer is demonstrated. Specific features of field localization at the Tamm plasmon polariton and defect mode frequencies are analyzed.

The exploration of alternative antimalarial therapeutics is a requisite for the emergence of resistance against Artemisinin. Considering the required cost and time length of classical small molecule drug discovery process, phytochemical screening of traditionally used medicinal plant which are repertoire of active compounds with antimalarial activity has become popular. To investigate the antimalarial property of traditionally used medicinal plants, a number of Erythrina spp have been reviewed systematically where less studied E. fusca has been selected for further analysis. Phytochemical investigation yielded five compounds namely; Phaseolin, Phytol, β-amyrin, Lupeol, and Stigmasterol. In-vitro antimalarial drug sensitivity HRP-II ELISA was carried out against chloroquine (CQ) sensitive 3D7 and CQ-resistant Dd2 strains. Extracts showed significant antimalarial activity against 3D7 and Dd2 strains (IC₅₀ 4.94 – 22 µg/mL) and these compounds have been reported here for the first time. Molecular docking analysis showed high binding energy (−9.0 ± 0.32 kcal/mole) indicating high degree of interaction between Phaseolin and 14 clinically important Plasmodium falciparum proteins at the active site. Stable interaction was also observed between ligand and protein from molecular dynamics simulation analysis with high free energy (−75.156 ± 11.459) that substantiates the potential of Phaseolin as an antimalarial drug candidate.

We introduce the notion of generalized contraction on dualistic partial metric spaces. A fixed point theorem for mappings satisfying above mentioned contraction is obtained. Some consequences of our result are obtained. We construct an example to demonstrate the effectiveness of our result among the corresponding results in partial metric spaces. Our results provide substantial generalizations and improvements of several well known results existing in the comparable literature. We discuss an application of our fixed point results to show the existence of solution of functional equations.

In the construction business, which is known for its intricate and strategic nature, it is crucial to have efficient risk management in place. This is because various internal and external elements can cause disruptions to projects. Although the industry has had a historically negative reputation for risk analysis, the methodical process of identifying, analyzing, and managing risks has been more widely recognized and respected. This paper examines the historical progression of construction risk management, highlighting the need to identify and classify risks promptly. The study examines various risk factors related to finance, law, environment, and logistics. The study explores various risk management strategies, such as contract management, risk distribution, evaluation, mitigation, and sharing. The article discusses the significant impact of risk management software, such as Procore, PlanGrid, e-Builder, Autodesk BIM 360, and Oracle Primavera, on improving project results. The study finishes by highlighting the importance of proactive risk management in protecting against financial losses and maintaining a reputation in the construction business.

The increasing expansion of the use of renewable distributed generation (RDG) technologies in electrical networks such as solar plants or wind farms and others has changed the nature of the distributed system and transformed it from the traditional system into an efficient system. This system has led to various technical effects in the host networks, with regard to voltage, electrical energy losses, fault levels, stability and electrical energy quality. These effects are not generic to any network; It can be positive, negative or neutral depending on the structure of the studied network, its operational condition and the various technology of the distributed generators. This research aims to quantitatively correct the effects of (RDG) in terms of voltage and electrical energy losses in the host networks. , since efficient distribution systems contain generators of a special nature and often contain bidirectional flux energy, it was necessary to construct a mathematical model of the distribution system hosting RDG units, which is fundamentally different from the traditional model of defining the reference electrical distribution bus bar. In order to achieve the systematic analysis, evaluation criteria and indicators were determined and mathematical formulas for them were completed. Based on the accomplished mathematical basis, an algorithm designed in such a way that it can be applied to any multi-voltage distribution system and to different distributed regenerative generation techniques is proposed. To demonstrate the algorithm's capabilities, it was tested on typical distribution networks using Factory Power DigSilent software, which is somewhat similar to MATLAB but more suitable for large capacity systems.

Visually impaired people encounter many impediments and challenges in their lives such as related to their mobility, education, communication, use of technology, and others. This paper reports the results of an online survey to understand the requirements and challenges blind and visually impaired people face in their daily lives regarding the availability and use of digital devices. The survey was conducted among the blind and visually impaired in Saudi Arabia using digital forms. A total of 164 people responded to the survey most of them using the VoiceOver function. People were asked about the use of smart devices, special devices, operating systems, object recognition apps, indoor and outdoor navigation apps, virtual digital assistive apps, the purpose (navigation, education, etc.) of and difficulty in using these apps, the type of assistance needed, the reliance on others in using the assistive technologies, and the level of satisfaction from the existing assistive technologies. The majority of the participants were 18 – 65 years old with 13% under 18 and 3% above 65. Sixty-five percent of the participants were graduates or postgraduates and the rest only had secondary education. White Cane, mobile phones, Apple iOS, Envision, Seeing AI, VoiceOver, and Google Maps were the most used devices, technologies, and apps used by the participants. Navigation at 39.6% was the most reported purpose of the special devices followed by education (34.1%) and office jobs (12.8%). The information from this survey along with a detailed literature review of academic and commercial technologies for the visually impaired was used to establish the research gap, design requirements, and a comprehensive understanding of the relevant landscape, which in turn was used to design smart glasses called LidSonic for visually impaired.

Wheat has a large and diverse repertoire of NLRs involved in disease resistance, with over 1,500 NLRs detected in some studies. These NLR genes occur as singletons or clusters containing copies of NLRs from different phylogenetic clades. The number of NLRs and cluster size can differ drastically among ecotypes and cultivars. Primarily, duplication has led to the evolution and diversification of NLR genes. Among the various mechanisms, whole genome duplication (WGD) is the most intense and leading cause, contributing to the complex evolutionary history and abundant gene set of hexaploid wheat. Tandem duplication or recombination is another major mechanism of NLR gene expansion in wheat. The diversity and divergence of duplicate NLR genes are responsible for the broad-spectrum resistance of most plant species with limited R genes. Understanding the mechanisms underlying the rapid evolution and diversification of wheat NLR genes will help improve disease resistance in crops. The present review focuses on the diversity and divergence of duplicate NLR genes and their contribution to wheat disease resistance. Moreover, we provide an overview of disease resistance-associated gene duplication and the underlying strategies in wheat.

Lung cancer is a deadly disease if not diagnosed in its early stages. However, early detection of lung cancer is a challenging task due to the shape and size of its nodules. Radiologists need support from automated tools for precise opinion. Automated detection of the affected lungs nodule is difficult because of the shape similarity among healthy tissues. Over the years, several expert systems have been developed that help radiologists to diagnose lung cancer. In this article, we propose a framework to precisely detect lungs cancer by classifying it between benign and malignant nodules. The framework is tested using the subset of the publicly available at the Lung Image Database Consortium image collection (LIDC-IDRI). Multiple techniques including filtering and noise removing are applied for pre-processing. Subsequently, the OTSU and the semantic segmentation are used to accurately detect the unhealthy lungs nodules. In total, 13 nodules features were extracted using Principal Components Analysis (PCA) algorithm. Four optimal features are selected based on the classification performance. In the classification phase, 9 different classifiers are used along with two types of validation schemes i.e. train test holdout validation with 70-30 data split and 10 fold cross-validation. Our experiments show that the proposed system provides 99.23\% accuracy using logic boost classifier.

For a considerable length of time synthetic composts are utilized to satisfy the dirt necessity of supplements and yield, however huge measure of these substance manures are hazardous for condition, advantageous microorganisms, creatures, and people also. In this way, natural inviting and savvy biofertilizers are utilized. Biofertilizer are the substances which contain microorganisms those microorganisms might be growths, microscopic organisms, and protozoa which have capacity to build ripeness of soil by Nitrogen obsession, Phosphorous solubilization, and Iron sequestration. These cycles convert insoluble type of supplements into solvent structure and make it accessible to the foundations of plant which effectively take them up and use them. There are assortment of the yields whose profitability can be expanded by applying biofertilizer, for example, rice, oat, and other grain crops. In this audit we experience the method of utilization of biofertilizers, and how the assistance the plants and in which they help.

Modern day construction is widely influenced using concrete-steel composite columns. A lot of research on concrete-steel composite columns is being carried out around the world. The rapid growth in concrete-steel composite construction has widely decreased the use of conventional reinforced cement concrete construction (R.C.C), and the steel construction practices. The concrete-steel composite construction has obtained an extensive receiving around the globe. As Pakistan is a developing country, so, it is relatively a new concept for its construction industry when compared with the developed countries around the globe. Although, the R.C.C construction is suitable and economical for construction of framing systems of low-rise buildings, however, the increased dead load, span restrictions, less stiffness and risky formwork makes it uneconomical and unviable when it comes across the construction of intermediate to high-rise buildings. This research is an effort to learn the cost effectiveness, increased or decreased stiffness, and change on the functionality of the composite construction for intermediate to high-rise buildings constructed in Pakistan. A Base + Ground + 11 storey commercial building is selected for this study. A comparison is made between conventional R.C.C columns structure and concrete-encased composite columns structure. The equivalent static nonlinear analysis is performed using ETABS 2017 software. Although, for Base + Ground + 11 storey building, the construction cost of concrete-encased composite structure is 7.7% more than the conventional R.C.C columns structure, but the concrete-encased composite structure will have 13.013% more constructed floor area. This increased floor area helps to settle the cost difference between the two structures.

Human displacement is on the rise globally, and the increase in the burden of tuberculosis (TB) is also attributed to migrations worldwide. A significant number of such displacement occur in regions with considerably higher areas of TB burden. Displacements may delay in TB diagnosis and treatment, which possibly will lead to TB transmission among healthy individuals. In this study, we assessed the association of existing determinants after a protracted internal displacement of people with the delay in TB diagnosis and treatment outcomes. A cross-sectional study was conducted on internally displaced TB patients registered at selected health facilities in three urban districts of Pakistan from March 2019 to February 2020. The univariate and multivariate logistic regression model was used to assess the delay in diagnosis and treatment outcomes. IDPs with delay in initiation of treatment beyond 30 days were at high possibility of unsuccessful TB treatment outcomes (adjusted odds ratio AOR,2.60; 95% CI 1.06-6.40). Analysis of factors that affect health seeker behavior and timely treatment showed a significant association (p<0.05) in-between age group 55-65 years (AOR, 2.66; 95% CI 1.00-7.07), female patients (AOR, 2.42; 95% CI 1.21-4.81), visited non-formal health provider (AOR, 8.81; 95% CI 3.99-19.46), self-medication (AOR, 2.72; 95 % CI 1.37-5.37), poor knowledge of TB (AOR, 11.39; 95% CI 3.31-39.1), and perceived stigma (AOR, 8.81; 95% CI 3.99-19.4). Prolong delay in treatment was associated with unfavorable treatment outcomes among IDPs, more specifically. As migrants and IDPs are more likely to experience an interruption in care due to overall exclusion from social and health care services. Therefore, it is imperative to understand the barriers in providing public health care services, particularly in preventing and treating TB.

Hydrogels have gained significant attention as vehicles for transdermal delivery systems. These polymeric-structured substances have been implemented in pharmaceutical and cosmetic applications. Many factors are employed in their preparation. Light, pH, temperature and specific molecules ligands are commonly used in the production of hydrogels. The Transdermal delivery system (TDD) is a widely used route, used to deliver actives/drugs via the skin. Hydrogels as a TDD have been shown to be efficient in enhancing the efficacy in delivering the actives and drugs. The aim of this review is to discuss the hydrogels application in both dermatological therapeutic and cosmetic applications, covering the types, and properties of hydrogel polymer networks. Furthermore, this review presents one of the most extensively used polymers (Hyaluronic acid HA) in this field and discusses the properties, preparation methods and applications of HA hydrogel patches as a delivery system, including methods of loading the actives and the releasing of these actives from them.

With the advent of digitization, the integration of advanced technologies in operations and projects across all sectors is in progress. Accordingly, efforts are being made to utilize cutting-edge technologies to improve the circularity of the built environment. This study aimed to review the existing applications and limitations of building information modeling (BIM) tools for circular economy (CE) implementation from this perspective. A literature review was conducted to provide an overview of the use of BIM tools for conducting life cycle assessments, energy analysis, waste management, and formulation of material passports for buildings. It was found that BIM tools, which are available across all life cycle phases of building, have a great potential to improve the circularity of the sector. The overview provided on the use of various BIM tools may help stakeholders of the built environment understand the role of BIM for CE adoption in the sector.

The Global natural and manmade events are exposing the fragility of the tourism industry and its impact on the global economy. Prior to the COVID-19 pandemic, tourism contributed 10.3% to the global GDP and employed 333 million people but saw a significant decline due to the pandemic. Sustainable and smart tourism requires collaboration from all stakeholders and a comprehensive understanding of global and local issues to drive responsible and innovative growth in the sector. This paper presents an approach for leveraging big data and deep learning to dis-cover holistic, multi-perspective (e.g., local, cultural, national, and international) and objective information on a subject. Specifically, we develop a machine learning pipeline to extract parameters from academic literature and public opinions on Twitter, providing a unique and comprehensive view of the industry from both academic and public perspectives. The academic-view dataset was created from the Scopus database and contains 156,759 research articles from 2000 to 2022, which were modelled to identify 33 distinct parameters in 4 categories: Tourism Types, Planning, Challenges, and Media &amp; Technologies. A Twitter dataset of 485,813 tweets was collected over 18 months starting March 2021 to August 2022 to showcase public perception of tourism in Saudi Arabia, which was modelled to reveal 13 parameters categorized into two broader sets: Tourist Attractions and Tourism Services. Discovering system parameters are re-quired to embed autonomous capabilities in systems and for decision-making and problem-solving during system design and operations. The proposed approach improves AI-based information discovery by extending the use of scientific literature, Twitter, and other sources for autonomous, dynamic optimizations of systems, promoting novel research in the tourism sector and contributing to the development of smart and sustainable societies. The paper also presents a comprehensive knowledge structure and literature review of the tourism sector based on over 250 research articles.

A layout of urban waste fired zero emission power plant is described in this paper. The principle of layout, which comes from similar coal-fired plants retrieved from the literature, integrates gasification with a power generation section, and implements two parallel conversion processes, one supplied by the heat of the gasifier consisting of a thermoacousticmagnetohydrodynamic (TAMHD) generator, while in the second one the syngas is treated in order to obtain almost pure hydrogen, which is fed to fuel cells. The CO2 deriving from the oxidation of Carbon base is stocked in liquid form. The novelty of the proposed layout lies in the fact that the entire conversion is performed without solid moving parts. The resulting plant avoids any type of emissions in the atmosphere, increases mechanical efficiency as compared to traditional plants, thanks to the absence of moving parts, nonetheless, resolving at its root the ever-increasing waste-related pollution problems.

Wind energy is becoming an essential source of power for countries which have the aim to reduce greenhouse gases emission and mitigate the effects of global warming. The Wind Turbines (WTs) installed around the globe is increasing significantly every year. The dramatic increase in wind power has encountered quite a few challenges, among which the major issues are availability and reliability. The unexpected failure in WTs Gearbox (GB) ultimately increases the Operation and Maintenance (O&M) cost. The identification of faults in the earlier stages before it turns to catastrophic damage to other components of WT is crucial. This research deals with the prediction of WT failures by using a Supervisory Control and Data Acquisition (SCADA) system. The main aim is to forecast the temperature of the WTs GB to predict the impending overheating of the GB at an early stage. The earlier prediction will help to optimize the maintenance period and to save maintenance expenses and, even more important, generate warnings in due time to avoid major damages or even technical disasters. In the proposed method we compared six different machine learning (ML) models based on error and accuracy of prediction. The bagging regressor is the best ML model, which results in the mean square error of 0.33 and R of 99.8 on training data. The bagging regressor is then used to predict the fault in the WT GB, which detected the anomalous behavior of WT GB 59 days earlier than the actual failure. This model also detects the extremely unusual behavior of the GB 9 days earlier than a complete failure.

High antioxidants level in food is gradually becoming popular because of the enhanced risk of oxidative stress in humans. Bread wheat is rich in vital antioxidants but its major bioactive compounds are not available for the human. This study was conducted with the aim to enhance the phytochemical constituents and antioxidative activity of wheat grains by fermenting it with the use of Bacillus subtilis KCTC 13241. The antioxidative potential was determined by DPPH (2,2-diphenyl-1-picryl- hydrazyl) and ABTS (3-ethyl-benzothiazo- line-6-sulfonic acid) radical scavenging assay as well by the concentration of amino acids, flavonoids, minerals, carbohydrates, and phenolic compounds. Different varieties showed different free radical scavenging potential on fermentation, which was significantly high with respect to their corresponding unfermented wheat varieties. The highest potential was found in a fermented wheat variety named Namhae and this combination can be used in the pharmaceutical and food industries.

This article investigates the features of heat and mass transfer for the steady two-dimensional Williamson nanofluid flow across an exponentially stretched surface depending on suction/injection. The boundary conditions incorporate the impacts of the Brownian motion and thermophoresis boundary. The analysis of heat transfer is carried out for the two cases of prescribed exponential order surface temperature (PEST) and prescribed exponential order heat flux (PEHF). The ongoing flow problem is mathematically modeled under the basic laws of motion and heat transfer. The similarity variables are allowed to transmute the governing equations of the problem into a similarity ordinary differential equation (ODEs). The solution of this reduced non-linear system of ODEs is supported by the Homotopy analysis method (HAM). The combination of HAM arrangements is acquired by plotting the h-curve. In order to evaluate the influence of several emergent parameters, the outcomes are presented numerically and are plotted diagrammatically as a consequence of velocity, temperature and concentration pro les.

The cross-linked microspheres were prepared and loaded with Favipiravir SARS-CoV-2 antiviral drug, by copolymerization of chitosan (CS) with a polysaccharide extracted from fresh pomegranate peels. Moreover, glutaraldehyde (Glu) has been used as chemical cross-linker ,and sodium hexametaphosphate (SHMP) as physical cross-linker. The extracted polysaccharide was analyzed and different techniques have been used and the analyses leads to the fact that it is pectin .The surface morphology of the prepared microspheres was studied use scanning electron microscope where the size and the shape factor (S) of Glu microspheres have shown high values(74.27μm) and (0.852) respectively means their surfaces are tends to roughness, whereas the SHMP microspheres have shown size particle(20.47μm)and shape factor (0.748) which gives indication that the SHMP microspheres have smooth surfaces. The swelling studies have shown that Glu microspheres have higher degree of swelling which means SHMP microspheres are more compact. The prepared microspheres have shown more Loading percentage of Favipiravir antiviral drug in SHMP microspheres(37%w/w)in comparison with Glu microspheres(35%w/w) where the electrostatic interaction between the Favipiravir ions and SHMP anions help for more loading. The microspheres prepared under different types of cross-linking have shown initially burst release of Favipiravir and followed by a step of controlled release for a certain time where its period depends on the pH of the release media. Both Glu and SHMP cross-linked microspheres have shown high controlled release time in buffered release solution of pH 7.4 and for a less periods in pH 1.3 and pH 9.4 which may related to the type of electrostatic interactions between drug and polymer system and their reactions with release solution ions.

Background Increasingly, healthcare organizations are using technology for the efficient management of data. The aim of this study was to compare the data quality of digital records with the quality of the corresponding paper-based records by using data quality assessment framework. Methodology We conducted a desk review of paper-based and digital records over the study duration from April 2016 to July 2016 at six enrolled TB clinics. We input all data fields of the patient treatment (TB01) card into a spreadsheet-based template to undertake a field-to-field comparison of the shared fields between TB01 and digital data. Findings A total of 117 TB01 cards were prepared at six enrolled sites, whereas just 50% of the records (n=59; 59 out of 117 TB01 cards) were digitized. There were 1,239 comparable data fields, out of which 65% (n=803) were correctly matched between paper based and digital records. However, 35% of the data fields (n=436) had anomalies, either in paper-based records or in digital records. 1.9 data quality issues were calculated per digital patient record, whereas it was 2.1 issues per record for paper-based record. Based on the analysis of valid data quality issues, it was found that there were more data quality issues in paper-based records (n=123) than in digital records (n=110). Conclusion There were fewer data quality issues in digital records as compared to the corresponding paper-based records. Greater use of mobile data capture and continued use of the data quality assessment framework can deliver more meaningful information for decision making.

This article aims to reflect upon the relevance of Decolonization methodologies with the Theses on Feuerbach. Somehow, all the Indigenous scholars started from new Marxist like Paulo Freire, Frantz Fanon, but not from classic Marx. To us, the German Ideology of young Marx only resembles the pioneering sources of Indigenous methodology. This discussion is thus a reflection of our studies and a philosophic endeavor to talk about the marginal people of the world, and the scholars who engaged in and with the oppressed. However, we are not prepared to turn our attention away from all the vastness of Marx to a collection of potentially equally relevant to Indigenous methodology. This article concludes that the Theses on Feuerbach is the core of Marxist archaeology of knowledge or philosophy as a whole and has been wading in the Indigenous paradigm.

The sustainability of the planet and its inhabitants is in dire danger and is among the highest priorities on global agendas such as the Sustainable Development Goals (SDGs) of the United Nations (UN). Solar energy -- among other clean, renewable, and sustainable energies -- is seen as essential for environmental, social, and economic sustainability. Predicting solar energy accurately is critical to increasing reliability and stability, and reducing the risks and costs of the energy systems and markets. Researchers have come a long way in developing cutting-edge solar energy forecasting methods. However, these methods are far from optimal in terms of their accuracies, generalizability, benchmarking, and other requirements. Particularly, no single method performs well across all climates and weathers due to the large variations in meteorological data. This paper proposes SENERGY (an acronym for Sustainable Energy), a novel deep learning-based auto-selective approach and tool that, instead of generalising a specific model for all climates, predicts the best performing deep learning model for GHI forecasting in terms of forecasting error. The approach is based on carefully devised deep learning methods and feature sets through an extensive analysis of deep learning forecasting and classification methods using ten meteorological datasets from three continents. We analyse the tool in great detail through a range of metrics and methods for performance analysis, visualization, and comparison of solar forecasting methods. SENERGY outperforms existing methods in all performance metrics including Root Mean Square Error (RMSE), Mean Absolute Error (MAE), Mean Absolute Percentage Error (MAPE), Forecast Skills (FS), Relative Forecasting Error, and the normalised versions of these metrics. The proposed auto-selective approach can be extended to other research problems such as wind energy forecasting and predict forecasting models based on different criteria (in addition to the minimum forecasting error used in this paper) such as the energy required or speed of model execution, different input features, different optimisations of the same models, or other user preferences.

A new class of nano-cube core-shell heterostructures containing Ag coating on the top of WO₃ was fabricated. Physical vapor deposition was used to produce WO₃ based nano-heterostructures. All kind of wet toxic chemical process was avoided to make the process simple and contaminant free. Sputtering of WO₃ and a subsequent thermal annealing process was done to create nano-cubes of WO₃. After that, sputtering of Ag was performed to form the Ag-WO₃ core-shell nano-heterostructures (CSNH). The CSNHs were characterized using field emission scanning electron microscopy (FESEM), energy dispersive spectroscopy (EDS), X-ray diffraction analysis (XRD) and UV-vis spectroscopy. The morphologies, elemental analysis, interfaces, crystallinity, phases, and chemical compositions were analyzed. The bottom-up growth of WO₃ nanocubes was studied using different time periods at 900°C. Ag coating was also studied before and after annealing. Finally, an optical property (band gap) was also analyzed using Tauc plot derive from absorption spectra. The tailoring the band gap of WO₃ from ~2.9eV to ~ 2.45 eV was observed while Ag-WO₃ CSNH formed.

Biodiversity has become an issue of global anxiety over the past decades due to its rapid decline worldwide. Bangladesh as one of the most densely populated countries in the world is no more exception. The country, although, was once very rich in biodiversity, during the last few decades as a consequence of the rapid reduction in forest area, urbanisation, habitat modification, unsustainable natural resources use and collection and overall climate change it has decreased alarmingly. Of late, the government, as a signatory of various regional and international conservation treaties, has taken various initiatives to improve country’s dwindling biodiversity. This paper reviews the present situation of biodiversity in Bangladesh, management trends and major causes of biodiversity loss. A separate statutory body is fundamental to ensure conservation, sustainable use and equitable sharing of benefits arisen from biodiversity in the country.

Despite of being an exceptionally biodiversity rich country, the forest coverage of Bangladesh is declining at an alarming rate. Declaration and management of protected areas in this regard is one of the efforts from government side to tackle the loss of biodiversity. The limited numbers of forest-protected areas (FPA), established to conserve the dwindling forest biodiversity of the country with high pressure on them for timber, non-timber forest products, and fuelwood - makes their management challenging. Moreover, most of the FPAs of the country declared only in the recent decades with very limited infrastructure, manpower and policy support for monitoring and governance. Some people-centred approaches for the management of FPAs and alternative livelihood and income generation subsidies although made available through a few project interventions, their number are still inadequate and performance remains less than satisfactory. This chapter provides a critical review of the FPAs of Bangladesh looking at their role in biodiversity conservation, management challenges, and key lessons from previous management interventions with recommendations for the future. It has been revealed that the FPA system of Bangladesh still poorly represents the diverse forest ecosystems with relatively small forest size and lack of corridors for the movement of wildlife. There are ample opportunities to render co-management of FPAs an effective strategy to minimize the conflicts in FPAs management in the country. It is, however, important to ensure the access of local forest-dependent people to different alternative income generating options that may adequately support their livelihoods.

To protect power lines, distance relays are used which can rely on a modified distance resistance. But usually the operating range of these relays changes as the network conditions change (network topology, load value, output value, etc.) and leads to false trips, By using methods that can process information and recognize patterns, for example, the use of micro and intelligent processor algorithms can use the new relays with high precision and thus provide adequate protection. In this study, a distance relay was modeled using a neural network, and it was observed that the neural relay had higher accuracy than the conventional relay. In addition to detecting the fault and its location, type and phase of the fault, three-stage simultaneous protection can be performed. As a result, the number of linear relays can be reduced by using relays based on neural technologies. An MLP (multilayer perceptron) neural network is used to model a sequence of distances.

This study investigates the impact of Foreign Direct Investment (FDI) on economic growth and examines the causality between FDI and economic growth in Bangladesh during 1972-2013. Gross Domestic Product (GDP), export performance (EXP), Foreign Direct Investment (FDI), and Gross Fixed Capital Formation (GFCF) are considered to capture the objective of the study. The study methodology includes some systematic steps. As the data used in the study is time-series in nature, the author employs unit root tests, and in this case, Augmented Dickey-Fuller (ADF) and Phillips-Perron (PP) tests are used. Then Johansen’s cointegration test, Granger causality test, regression with Newey-West Standard Error and Vector Error Correction Model (VECM) are applied. By using the ADF and PP test the study reveals that the variables of four-time series are integrated of I (1) i.e. they are stationary at first difference. Regression analysis result demonstrates that FDI has a positive effect on economic growth. The Granger Causality test discloses that there is a unidirectional relationship between FDI and economic growth. But the VECM estimation finds that in the long run FDI negatively affects economic growth.

Advancements in technology, policies, and cost reductions have led to rapid growth in wind power production. One of the major challenges in wind energy production is the instability of wind power generation due to weather changes. Efficient power grid management requires accurate power output forecasting. New wind energy forecasting methods based on deep learning are better than traditional methods, like numerical weather prediction, statistical models, and machine learning models. This is more true for short-term prediction. Since there is a relationship between methods, climates, and forecasting complexity, forecasting methods do not always perform the same depending on the climate and terrain of the data source. This paper proposes a novel model that combines the variational mode decomposition method with a long short-term memory model, developed for next-hour wind speed prediction in a hot desert climate, such as the climate in Saudi Arabia. We compared the proposed model performance to two other hybrid models, six deep learning models, and four machine learning models using different feature sets. Also, we tested the proposed model on data from different climates, Caracas and Toronto. The proposed model showed a forecast skill between 61% to 74% based on mean absolute error, 64% to 72% based on root mean square error, and 59% to 68% based on mean absolute percentage error for locations in Saudi Arabia.

Telemedicine is the use of Information and Communication Technology (ICT) for clinical health care from a distance. The exchange of radiographic images and electronic patient health information/records (ePHI/R) for diagnostic purposes has the risk of confidentiality, ownership identity, and authenticity. In this paper, a data hiding technique for ePHI/R is proposed. The color information in the cover image is used for key generation, and stego-images are produced with ideal case. As a result, the whole stego-system is perfectly secure. This method includes the features of watermarking and steganography techniques. The method is applied to radiographic images. For the radiographic images, this method resembles watermarking, which is an ePHI/R data system. Experiments show promising results for the application of this method to radiographic images in ePHI/R for both transmission and storage purpose.

Evolution remains an incessant process in viruses, allowing them to elude host immune response and induce severe diseases, impacting the diagnostic and vaccine effectiveness. Predicting emerging viral genomes is crucial, particularly in diseases like dengue, where viruses disrupt host cells, leading to fatal outcomes. Deep learning has been applied to predict dengue fever cases; there has been relatively less emphasis on its significance in forecasting emerging Dengue Virus (DENV) serotype. While Recurrent Neural Networks (RNN) were originally designed for modeling temporal sequences, our proposed DL-DVE generative and classification model, trained on complete genome data of DENV, transcends traditional approaches by learning semantic relationships between nucleotides in a continuous vector space instead of representing contextual meaning of nucleotide characters. Leveraging 2000 publicly available DENV complete genome sequences, our Long Short-Term Memory (LSTM) based generative and Feedforward Neural Network (FNN) based classification DL-DVE model showcases proficiency in learning intricate patterns and generating sequences for emerging serotype of DENV. The generative model showed accuracy of 93% and the classification model provided insight into the specific serotype label, corroborated by BLAST search verification. Evaluation metrics such as ROC-AUC value 0.818, accuracy, precision, recall and F1 score all to be around 99.00%, demonstrated the classification model’s reliability.  Our model classified the generated sequences as DENV-4, exhibiting 65.99% similarity to DENV-4 and around 63-65% similarity with other serotypes, indicating notable distinction from other serotypes. Moreover, the intra-serotype divergence of sequences with a minimum 90% similarity underscored their uniqueness. We analyzed the conserved motifs in the genome through MEME Suite (version 5.5.5). Our research strives to contribute to the ongoing fight against the Dengue virus by offering predictive insights into its genomic evolution. Looking ahead, proactive predictive modeling before mutations occur holds potential for guiding vaccine design and diagnostic kit development.

Structural design optimization (SDO) plays a pivotal role in enhancing various aspects of construction projects, including design quality, cost-efficiency, safety, and structural reliability. Recent endeavors in academia and industry have sought to harness the potential of Building Information Modeling (BIM) and optimization algorithms to optimize SDO and improve design outcomes. This review paper aims to synthesize these efforts, shedding light on how SDO contributes to project coordination. Furthermore, the integration of sustainability considerations and the application of innovative technologies and optimization algorithms in SDO necessitate more interactive early-stage collaboration among project stakeholders. This study offers a comprehensive exploration of contemporary research in integrated SDO employing BIM and optimization algorithms. It commences with an exploratory investigation, employing both qualitative and quantitative analysis techniques following the PRISMA systematic review methodology. Subsequently, an open-ended opinion survey was conducted among construction industry professionals in Europe. This survey yields valuable insights into the coordination challenges and potential solutions arising from technological shifts and interoperability concerns associated with widespread SDO implementation. These preliminary steps of systematic review and industry survey furnish a robust knowledge foundation, enabling the proposal of an intelligent framework for automating early-stage sustainable structural design optimization (ESSDO) within the construction sector. The framework ESSDO addresses the challenges of fragmented collaboration between architects and structural engineers. This proposed framework seamlessly integrates with the BIM platform, i.e., Autodesk Revit for architects. It extracts crucial architectural data and transfers it to the structural design and analysis platform, i.e., Autodesk Robot Structural Analysis (RSA), for structural engineers via the visual programming tool Dynamo. Once the optimization occurs, optimal outcomes are visualized within BIM environments. This visualization elevates interactive collaborations between architects and engineers, facilitating automation throughout the workflow and smoother information exchange.

Vehicle driveability is one of the important vehicle attributes in range-extender electric vehicles due to the electric motor torque characteristics at low-speed events. The process of validating and rectifying vehicle driveability attributes is typically utilised by a physical vehicle prototype that can be expensive and required several design iterations. In this paper, a model-based energy method to assess vehicle driveability is presented based on a high-fidelity 49 degree-of-freedom powertrain and vehicle systems. Multibody dynamics components were built according to their true centre of gravity relative to the vehicle datum for providing an accurate system interaction. The work covered a frequency at less than 20 Hz. The results that consisted of the component frequency domination are structured and examined to identify the low-frequency sensitivity based on different operating parameters such as a road surface coefficient. An energy path technique was also implemented on the dominant component by decoupling its compliances to study the effect on the vehicle driveability and low-frequency response. The outcomes of the research provided a good understanding of the interaction across the sub-systems levels. The powertrain rubber mounts were the dominant components that controlled the low-frequency contents (< 15.33 Hz) and can change the vehicle driveability quality.

Mental health issues can have significant impacts on individuals and communities and hence on social sustainability. There are several challenges facing mental health treatment, however, more important is to remove the root causes of mental illnesses because doing so can help prevent mental health problems from occurring or recurring. This requires a holistic approach to understanding mental health issues that are missing from the existing research. Mental health should be understood in the context of social and environmental factors. More research and awareness are needed, as well as interventions to address root causes. The effectiveness and risks of medications should also be studied. This paper proposes a big data and machine learning-based approach for the automatic discovery of parameters related to mental health from Twitter data. The parameters are discovered from three different perspectives, Drugs & Treatments, Causes & Effects, and Drug Abuse. We used Twitter to gather 1,048,575 tweets in Arabic about psychological health in Saudi Arabia. We built a big data machine learning software tool for this work. A total of 52 parameters were discovered for all three perspectives. We defined 6 macro-parameters (Diseases & Disorders, Individual Factors, Social & Economic Factors, Treatment Options, Treatment Limitations, and Drug Abuse) to aggregate related parameters. We provide a comprehensive account of mental health, causes, medicines and treatments, mental health and drug effects, and drug abuse, as seen on Twitter, discussed by the public and health professionals. Moreover, we identify their associations with different drugs. The work will open new directions for social media-based identification of drug use and abuse for mental health, as well as other micro and macro factors related to mental health. The methodology can be extended to other diseases and provides a potential for discovering evidence for forensics toxicology from social and digital media.

Farmers’ conventional tillage (CT) and residue removal practices in rice-maize systems in South Asia’s Eastern Gangetic Plain (EGP) are input-intensive, costly and soil degradative. We conducted a rice-maize-mungbean (R-M-MB) system experiment with six tillage and three residue management treatments in Bangladesh representing the EGP. Maize yields were significantly (p≤0.05) higher under permanent (PB) or fresh (FB) beds and strip tillage (ST) than CT but no differences in mungbean yields. Rice yields under PB, FB and CT were similar, but significantly higher than under zero or minimum tillage and ST. Yields of all crops increased significantly (p≤0.05) with residue retention compared to no retention. Total system productivity was highest under PB followed by FB and ST. Compared with CT, gross margins in PB, FB and ST increased by 18, 13 and 11%, and soil organic matter (SOM) and total N contents across tillage treatments increased by 11-16% and 12-24%, respectively. After three years, SOM and total N and available P and S contents increased significantly (p≤0.05) by residue retention. Results demonstrate the potential of PB, FB and ST with residue retention, for improving the productivity, profitability and soil health under R-M-MB systems in Bangladesh and similar soils in the EGP.

The consumption and sale of fresh-cut products and salads have been growing tremendously in the present era. Therefore, the microbial safety of such products is of great concern. In the current study, a survey of general microbiological safety of fresh-cut produce and salads at quick-service restaurants (QSR) was undertaken across the Kingdom of Saudi Arabia. These findings were compared with microbiological criteria for foodstuffs by Saudi standards, metrology, and quality organization SASO-GSO-1016. Of the 82 samples of fresh-cut produce, 7% of samples were found to be unsatisfactory or beyond the acceptable limits. TPC count was unsatisfactory at 22%, coliform at 48%, and Staphylococcus aureus at 4%. For 108 samples for fresh salads, 11% of samples were found to be unsatisfactory or beyond the acceptable limits,13%, 27%, 4%, and 27% of samples showed an unsatisfactory range of TPC, coliforms, S. aureus, and Escherichia coli, respectively. The fresh-cut produce and salads were microbiologically safe in the central region compared to the eastern region followed by the western region. The relatively higher count was found in green pepper, mixed vegetables, and lettuce followed by fresh-cut onions and coleslaw salads. No Salmonella was detected in both fresh-cut produce and salads. The restaurants should be more stringent in their processing to ensure the consumer safety. Washing and sanitization of produce is the only way to reduce the diffusion of food borne pathogens.

Big data has revolutionised science and technology leading to the transformation of our societies. High Performance Computing (HPC) provides the necessary computational power for big data analysis using artificial intelligence and methods. Traditionally HPC and big data had focused on different problem domains and had grown into two different ecosystems. Efforts have been underway for the last few years on bringing the best of both paradigms into HPC and big converged architectures. Designing HPC and big data converged systems is a hard task requiring careful placement of data, analytics, and other computational tasks such that the desired performance is achieved with the least amount of resources. Energy efficiency has become the biggest hurdle in the realisation of HPC, big data, and converged systems capable of delivering exascale and beyond performance. Data locality is a key parameter of HPDA system design as moving even a byte costs heavily both in time and energy with an increase in the size of the system. Performance in terms of time and energy are the most important factors for users, particularly energy, due to it being the major hurdle in high performance system design and the increasing focus on green energy systems due to environmental sustainability. Data locality is a broad term that encapsulates different aspects including bringing computations to data, minimizing data movement by efficient exploitation of cache hierarchies, reducing intra- and inter-node communications, locality-aware process and thread mapping, and in-situ and in-transit data analysis. This paper provides an extensive review of the cutting-edge on data locality in HPC, big data, and converged systems. We review the literature on data locality in HPC, big data, and converged environments and discuss challenges, opportunities, and future directions. Subsequently, using the knowledge gained from this extensive review, we propose a system architecture for future HPC and big data converged systems. To the best of our knowledge, there is no such review on data locality in converged HPC and big data systems.

City zones have become increasingly overcrowded as a result of the extensive population widening ratio and the swift relocation of people from villages. The traffic monitoring process is a major issue in these areas due to the massive traffic flow on the roads. This research proposed a cluster-based improved authentication and communication scheme for an Intelligent Transportation System in Vehicular AdHoc Networks (VANETs). Our primary objective is to optimize resource sharing in vehicular communication. We enhanced the reliability, scalability, and stability of fast-moving VANETs by introducing cluster-based routing schemes for Vehicle-to-Vehicle (V2V) and Vehicle-to-Infrastructure (V2I) communications. We used a third-party certification authority for vehicle authentication to address security and privacy concerns. Our proposed schemes support minimizing the end-to-end (E2E) delay and route request, in addition to reducing link failure. Our schemes’ leading yield includes throughput enhancement, TCP Socket Initialization time minimization, TCP handshake response speedup, and DNS lookup improvement. The schemes are centred on short-range peer-to-peer (P2P) wireless communication in a 400-meter radius cluster. This includes innovative P2P wireless communications on VANET using minimized resources. The proposed schemes deliver a secure authentication mechanism with a securely generated vehicle authentication key provided by a certification authority. Furthermore, we have developed RESTful APIs in vehicular communication for implementation purposes, and also offered and implemented algorithms for resource sharing regarding V2V and V2I communication. Ultimately, we evaluated the performance of our experiments.

Hyperlipidemia is an identified risk factor for metabolic syndrome, obesity and cardiovascular complications characterized by elevated levels of lipids in blood. The present study aimed to inhibit HMG-CoA reductase with 15-oxoursolic acid through in-vivo and in-silico assessments. HFD-induced hyperlipidemia in rats was developed with a marked increase in total cholesterol (58.34 ± 0.21 mg/dl), triglycerides (45.45 ± 0.39 mg/dl), LDL-c (66.12 ± 0.10 mg/dl), VLDL-c (19.34 ± 0.16 mg/dl), and a decrease in HDL-c (10.34 ± 0.18 mg/dl). The oral administration of 15-oxoursolic acid at a concentration of 30 mg/Kg b.w significantly reduced the serum concentration of total cholesterol (42.65 ± 0.54 mg/dl), triglycerides (32.33 ± 0.16 mg/dl), LDL-c (50.34 ± 0.15 mg/dl) and VLDL-c (13.15 ± 0.45 mg/dl) respectively and an increased in the serum HDL-c (18.56 ± 0.34 mg/dl). 15-oxo ursolic acid also caused a decrease in the coronary risk index and atherogenic risk index. In-silico studies of 15-oxoursolic acid with HMG-CoA reductase showed significant interaction capability with binding energy (-9.26805 Kcal/mol). It is concluded that 15-oxoursolic acid could significantly reduce the total cholesterol, triglycerides and LDL levels in HFD-induced hyperlipidemia rats which might lead to new medication with significant hypolipidemic potential.

This study was conducted in the Dhanu River and adjacent waters at Mithamain upazila (sub-district) under Kishoreganj district of Bangladesh to prepare a check list of available native fishes with their availability status, conservation perspectives, habitat preferences, population trends and intimidations. Data were collected monthly by direct field survey, focus group discussions, and personal interviews with fishers by using a semi-structured questionnaire and a pictorial check list of fish species. A total of 91 indigenous fish species of 59 genera belonging to 29 families under 11 orders were documented where 17.58% species was abundantly available, 27.47% was commonly available, 31.87% was moderately available and 23.08% was rarely available. Cypriniformes was found as the dominant order, consisting 37.36% of the fish species aggregation and Cyprinidae was the most dominant family with 32.97% of the entire species assemblage. Twenty four piscine species (26.37%) were under threatened category in Bangladesh which subsumed 3 critically endangered (3.29%), 11 endangered (12.08%), and 10 vulnerable species (10.99%). Notably globally threatened Cirrhinus cirrhosus, Channa orientalis, and Wallago attu were available there. Fish population trends of 24.18% and 59.34% of the entire fish species was found in decreasing trends in global and national level, respectively. Leading intimidation to the fish diversity was indiscriminately overfishing, followed by fishing by dewatering of wetlands, katha fishing method, use of deprecated fishing gears, climate change, etc. Minimization of anthropogenic impacts, assuring the flux of water round the year, enactments of fish laws, installation and management of fish sanctuaries, and raising public awareness can be effective for the conservation of existing fisheries resources.

When it comes to financial transactions and counterfeit detection systems, banknote classification is crucial. In this paper, we propose an approach for the classification of Kazakhstan banknote images integrating Learning Vector Quantization (LVQ) with Statistical Texture Feature Extraction using the Gray Level Co-occurrence matrix (GLCM). Our methodology demonstrates effectiveness in accurately classifying banknote images, as evidenced by experimental results. The comprehensive testing scenarios show promising outcomes, with the combination of GLCM and Color Histogram under the LVQ algorithm achieving a high accuracy of 94.87 percent at distance 1 and 90°. These findings indicate the robustness and practical viability of the proposed method for authenticating banknotes.

The Pashmina and Barbari are two famous goat breeds found in the wide areas of the Indo-Pak region. Pashmina is famous for its long hair-fiber (Cashmere) production while Barbari is not-selected for this trait. So, the mRNA expression profiling in the skin samples of both breeds would be an attractive and judicious approach for detecting putative genes involved in this valued trait. Here, we performed differential gene expression analysis on publicly available RNA-Seq data from both breeds. Out of 44,617,994 filtered reads of Pashmina and 55,995,999 of Barbari which are 76.48% and 73.69% mapped to the ARS1 reference transcriptome assembly respectively. A pairwise comparison of both breeds resulted in 47,159 normalized expressed transcripts while 8,414 transcripts are differentially expressed above the significant threshold. Among these, 4,788 are upregulated in Pashmina while 3,626 transcripts are upregulated in Barbari. Fifty-nine transcripts harbor 57 genes including 32 LOC genes and 24 are annotated genes which were selected on the basis of TMM counts > 500. Genes with ectopic expressions other than uncharacterized and LOC symbol genes are Keratins (KRT) and Keratin Associated Proteins (KRTAPs), CystatinA&6, TCHH, SPRR4, PPIA, SLC25A4, S100A11, DMKN, LOR, ANXA2, PRR9 and SFN. All of these genes are likely to be involved in keratinocyte differentiation, sulfur matrix proteins, dermal papilla cells, hair follicles proliferation, hair curvature, wool fiber diameter, hair transition, hair shaft differentiation and its keratinization. These differentially expressed reported genes are critically valuable for enhancing the quality and quantity of the pashmina fiber and overall breed improvement. This study will also provide important information on hair follicle differentiation for further enrichment analyses and introducing this valued trait to other goat breeds as well.

The fourth industrial revolution has resulted in the digitalization of projects and operations across all sectors. Accordingly, efforts are being made to utilize advanced technologies to improve the energy efficiency of the building sector. This study has reviewed the current application and limitations of cutting-edge technologies in this regard. An overview of the use of the Internet of Things (IoT), artificial intelligence (AI), digital twin (DT), and building information modeling (BIM) for energy efficiency of buildings has been provided. It has been found that the use of Industry 4.0 technologies, during the construction and operational phase of buildings, has a great potential to reduce energy consumption and emissions of the sector. This study may help stakeholders of the built environment to understand the role of industry 4.0 tools for energy efficiency of the sector.

Technological advancements and innovations have profoundly changed the lives of people giving rise to smart environments, cities, and societies. As homes are the building block of cities and societies, smart homes are critical to establishing smart living and are expected to play a key role in enabling smart cities and societies. The current academic literature and commercial advancements on smart homes have mainly focused on developing and providing smart functions for homes to provide security management and facilitate the residents in their various activities such as ambiance management. Homes are much more than physical structures, buildings, appliances, operational machines, and systems. Homes are composed of families and are inherently complex phenomena underlined by humans and their relationships with each other, subject to individual, intragroup, intergroup, and intercommunity goals. There is a clear need to understand, define, consolidate existing research, and actualize the overarching roles of smart homes, the roles of smart homes that would serve the needs of future smart cities and societies. This paper introduces our data-driven parameter discovery methodology and uses it to provide, for the first time, an extensive, rather fairly comprehensive, analysis of the families and homes landscape seen through the eyes of academics and the public using over a hundred thousand research papers and nearly a million tweets. We develop a methodology using deep learning, natural language processing (NLP), and big data analytics methods and apply it to automatically discover parameters that capture a comprehensive knowledge and design space of smart families and homes comprising social, political, economic, environmental, and other dimensions. The 66 discovered parameters and the knowledge space comprising 100s of dimensions are explained by reviewing and referencing over 300 articles from the academic literature and tweets. The knowledge and parameters discovered in this paper can be used to develop a holistic understanding of matters related to families and homes facilitating the development of better, community-specific, policies, technologies, solutions, and industries for families and homes, leading to strengthening families and homes, and in turn, empowering sustainable societies across the globe.

We live in a complex world characterised by complex people, complex times, and complex social, technological, and ecological environments. There is clear evidence that governments are failing at most public matters. The recent COVID-19 pandemic is a high example of global governance failure both at preventing such pandemics and managing the COVID-19 pandemic. It is time that all of us take responsibility and look into ways of collaboratively improving the governance of public matters, our matters. While there are many reasons for government failures, we believe the lack of information availability is a fundamental reason that limits the government’s ability to act smartly and allows the lack of transparency to creep into policy and action leading to corruption and failure. To this end, this paper introduces the concept of deep journalism, a data-driven deep learning-based approach for discovering multi-perspective parameters related to a topic of interest. We build three datasets (a newspaper, a technology magazine, and a Web of Science dataset) and discover the academic, industrial, public, governance, and political parameters for the transportation sector as a case study to introduce deep journalism and our tool DeepJournal (Version 1.0) that implements our proposed approach. We elaborate on 89 transportation parameters and hundreds of dimensions reviewing 400 technical, academic, and news articles. The findings related to the multi-perspective view of transportation reported in this paper show that there are many important problems seen by the public that industry and academia seem to not place their focus on. On the other hand, academia produces much broader and deeper knowledge on the subject such as a wide range of pollutions affecting the people and planet do not get to reach the public eye. Our deep journalism approach could find the gaps and highlight them to the public and other stakeholders.

Construction 4.0 is witnessing exponential growth in Digital Twin (DT) technology developments and applications, revolutionizing the adoption of Building Information Modelling (BIM) and other emerging technologies used throughout the lifecycle of the built environment. BIM provides technologies, procedures, and data schemas representing building components and systems. At the same time, DT enhances this with real-time data for cyber-physical integration, enabling live asset monitoring and better decision-making. Despite being in the early stages of development, DT applications have rapidly progressed in the AEC sector, resulting in a diverse literature landscape due to the various technologies and parameters involved in fully developing the DT technology. The intricate complexities inherent in digital twin advancements have confused professionals and researchers. This confusion arises from the nuanced distinctions between the two technologies, i.e., BIM and DT, causing a convergence that hinders realizing their potential. To address this confusion and lead to a swift development of DT technology, this study presents a holistic review of the existing research focusing on the critical components responsible for developing DT applications in the construction industry. The study identifies five crucial elements: technologies, maturity levels, data layers, enablers, and functionalities. Additionally, it identifies research gaps and proposes future avenues for streamlined DT developments and applications in the AEC sector. Future researchers and practitioners can target data integrity, integration and transmission, bi-directional interoperability, nontechnical factors, and data security to achieve mature digital twin applications for AEC practices. This study highlights the growing significance of DTs in construction and provides a foundation for further advancements in this field to harness its potential to transform built environment practices.

Let $\mathcal{\mathcal{S}}_{\cos}^{\ast}$ denote the class of normalized analytic functions $f$ in the open unit disk $\mathbb{D}$ satisfying the subordination $\dfrac{zf^{\prime}(z)}{f(z)}\prec\cos z$. In the second section of this article we find the sharp upper bounds for the initial coefficients $a_{3}$, $a_{4}$ and $a_{5}$ and the sharp upper bound for module of the Hankel determinant $|H_{2,3}(f)|$ for the functions from the class $\mathcal{S}_{\cos}^{\ast}$. The first result of the next section deals with the sharp upper bounds of the logarithmic coefficients $\gamma_{3}$ and $\gamma_{4}$ and we found in addition the sharp upper bound for $\left|H_{2,2}\left(F_{f}/2\right)\right|$. For obtaining these results we used the very useful and appropriate Lemma 2.4 of N.E. Cho et al. [Filomat 34(6) (2020), 2061--2072], and the technique for finding the maximum value of a three variable function on a closed cuboid. All the maximum found values were checked by using MAPLE\texttrademark{} computare software, and we also found the extremal functions in each cases. All of our present results are the best ones and give sharp versions of those recently published in [Hacet. J. Math. Stat. 52, 596--618, 2023].

Heart is composed of muscle cells called cardiomyocytes, including a specialized population, named pacemaker cells, that form the Cardiac Conduction System (CCS), responsible for generating the action potential dictating heart contractions. Failure of the CCS system leads to cardiac arrhythmias requiring complicated therapies and often surgical implantation of electrical pacemakers. However, recent research focusses on development of novel therapies using biological pacemakers aiming to substitute electrical devices. While most signalling pathways and transcription factors involved in the development of the pacemaker cells are known, the upstream regulatory networks need to be predicted through computer-based databases, mathematical modelling as well as functional testing of the regulatory elements in vivo, indicating the need for further research. Here we summarise the current knowledge about the vertebrate myocardial CCS system and development of the pacemaker cells and emphasise areas of future research to clarify the regulation of muscle pacemaker cells and ease development of biological therapies.

The efficiency of a new composite material of the layered double hydroxide (LDH) of ZnMgAl and rice husk biochar (RHB) for the removal of Cu(II) and Pb(II) ions from synthetic wastewater was investigated in this study. The images of scanning electron microscope showed extremely fine crystalline LDH particles decorated on the rough surface of the RHB while the succesful formation of the composite adsorbent (LDH/RHB) was confirmed by the corresponding energy dispersive X-ray and the Fourier-transform infrared spectroscopy. An equilibrium contact time of 30 and 15 min for Cu2+ and Pb2+, respectively, was proposed for the optimum performance of the batch adsorption process. The dose of the LDH/RHB adsorbent was optimized at 0.4 g yielding maximum adsorption capacities of 117 and 124 mg g-1 for Cu2+ and Pb2+, respectively, with corresponding maximum removal efficiencies of nearly 94% and 99%. The initial meta concentrations was optimized at 50 or 60 mg L-1 corresponding to maximum removal efficiencies or adsorption capacities. For the changing initial metal’s concentration, the removal efficiencies remained unchanged for up to 50 mg L-1 and decreased by about 50% by increasing the initial concentrations from 50 to 100 mg L-1. The adsorption capacities observed a linear increasing trend by increasing the initial concentrations from 5 to 60 mg L-1 and remained unchanged afterward up to 100 mg L-1. A solution pH of 6.0 yielded optimum results with an increasing trend in adsorption capacities and percentage removal by changing the solution pH from 2.0 to 7.0. Based on the best-fit of the pseudo second-order kinetic model to the experimental data, the chemisorption was suggested to be the controlling mechanism of adsorption. The fitting of the Langmuir model suggested a monolayer sorption of Cu2+ and Pb2+ in addition to a heterogeneous adsorption as supported by the fitting of the Temkin isotherm. The application of the Dubinin–Radushkevich isotherm proposed a physical adsorption (mean free energy of adsorption less than 8 kJ mol−1) of both heavy metal ions on the surface of the LDH/RHB adsorbent.

At present, sustainability and emerging technology are the most expressed issues in any supply chain management (SCM) sector. At the same time, pandemic makes consumers more concerned regarding health, and safe food with a sustainable way to access the current market. Thus, supervision and monitoring of product quality with symmetric traceability information in fresh food and fisheries SCM is significant. Research on food safety and traceability systems based on blockchain, internet of service (IoT), wireless sensor networks (WSN), and radio frequency identification (RFID) provides the solution of constancy from production to consumption. This review focused on the RFID-based traceability systems in fisheries SCM, which have been employed globally in the last fifteen years to ensure fish quality and security. Additionally, a summarized comparison study has presented different sectors’ traceability systems using RFID and their advantages over real-time applications. The outcome of this study will help future researchers to solve the crisis in terms of trust between consumers and the fisheries SCM. Thus, this review would be a guideline and solution for enhancing the reliability of RFID-based traceability in food SCM systems to ensure the integrity and reducing the opacity and asymmetry in the product information.

Biogeochemical models estimate soil organic carbon (SOC) sequestration, crop growth, and yield. The DeNitrification and DeComposition (DNDC) model was used to simulate soil SOC dynamics and harvested C-biomass in rice-wheat rotation under organic/inorganic fertilizations with conventional tillage (CT) and reduced tillage (RT). Before calibration, DNDC under-predicted harvestable grain C-biomass of rice by 29.22% to 42.14% and over-simulated grain C-biomass of wheat by 55.01% with equal amounts of NPK and animal manure applied under CT. However, after calibration by adjusting default values of soil/crop parameters, DNDC simulated harvestable grain C-biomass of both crops very close to observed values (only -2.81% to -6.17% less). DNDC also predicted effects of nutrient management practices on grain C-biomass of rice/wheat under CT/RT using d-index (0.76 to 0.96) and the calculated root mean squared error (RMSE of 165.36 to 494.18 kg C ha-1). DNDC simulated SOC trends for rice-wheat using measured values of several statistical indices. Regression analysis between modeled and observed SOC dynamics was significant with R2 ranging from 0.35 to 0.46 (p < 0.01), and intercept ranging from 0.30 to 1.34 (p < 0.65). DNDC demonstrated that combined inorganic and organic fertilization may result in higher C-biomass and more SOC sequestration in rice-wheat systems.

The comfort of human life depends on the quality, size, and reliability of the infrastructure projects. In the infrastructure systems, rapid growth is found, where the economic and sustainable impact has become a topic of significant concern for policies and government officials. To achieve con-straints of sustainable development, all the policies and actions over the infrastructure project's life cycle must be assessed. Decision-makers have adopted approaches for economic, social, and en-vironmental initiatives through Life Cycle Assessment (LCA) and Life Cycle Cost Analyses (LCCA) of infrastructure projects. The purpose of this review is to highlight the impact of per-forming LCA and LCCA in infrastructure projects. To achieve this goal, a systematic literature review methodology is adopted in which renowned databases, i.e., Web of Science, Science Direct, Emerald and Scopus were selected to extract the relevant literature. Using the PRISMA approach, 1251 publications were identified which were then filtered and 55 documents were included in the final review. In the extracted publications most, researchers were biased toward LCA and LCA individually, whereas few focused on integrated LCA and LCCA. The researchers assessed the costs and impact associated with the infrastructure project while there were less focused on the environmental cost. Besides this, techniques of economic, social, and environmental growth of infrastructure projects have been emphasized during the design phase because of substantial relations between infrastructure design and operation management. Moreover, a conceptual framework has been developed that will assist the decision-makers to consider the effects of LCA and LCCA on various aspects of the infrastructure project and how it impacts sustainability. In the last, a case study was performed to assess the developed framework with the incorporation of environmental impact cost.

Blockchain innovation stands out enough to be noticed and adopted in various countries and organizations around the world. Many businesses, including finance, medical services, inventory networks, security, libraries, and the internet of things, are currently under attack. For the benefit of the blockchain, many businesses incorporate blockchain technology into their frameworks. Despite its solidarity, blockchain faces a few challenges in security, protection, adaptability, and other areas. This paper examines the forward leap in blockchain innovation, as well as its applications and challenges. While many blockchain papers focus on digital currencies, IoT, and security, this paper focuses on the overall best in a class of blockchain innovation, its new twists and turns, and choices, particularly in areas other than cryptographic forms of money. The investigators' goal is to provide a thorough audit of the cryptography underlying blockchain to better understand the innovation. The examiners also conduct general research on people and venture blockchains, as well as future exploration opportunities and their implications for blockchain innovation.

Solar energy adoption worldwide has expanded exponentially due to a surge in international interest in producing clean energy and the declining cost of solar power plants and their technology. It is anticipated that by 2050, solar will have surpassed fossil fuels to become the primary source of energy. However, one of the main challenges associated with solar energy production is the instability of photovoltaic (PV) power generation because of weather changes. Short-term forecasting of the power output of photovoltaic systems is essential for efficient management of the power grid and energy markets. This paper aims to evaluate the ability of deep learning (DL) models to provide accurate forecasting of hourly global horizontal irradiance (GHI) using different sets of features, including weather and aerosol variables along with solar radiation components. The results show that the best forecast skills are achieved by the long short-term memory autoencoder (LSTM-AE) model.

We live in the information age and, ironically, meeting the core function of journalism – i.e., to provide people access to unbiased information – has never been more difficult. This paper explores deep journalism, our data-driven Artificial Intelligence (AI) based journalism approach to study how the LinkedIn media could be useful for journalism. Specifically, we apply our deep journalism approach to LinkedIn to automatically extract and analyse big data to provide the public with information about labour markets, people’s skills and education, and businesses and industries from multi-generational perspectives. The Great Resignation and Quiet Quitting phenomena coupled with rapidly changing generational attitudes are bringing unprecedented and uncertain changes to labour markets and our economies and societies, and hence the need for journalistic investigations into these topics is highly significant. We combine big data and machine learning to create a whole machine learning pipeline and a software tool for journalism that allows discovering parameters for age dynamics in labour markets using LinkedIn data. We collect a total of 57,000 posts from LinkedIn and use it to discover 15 parameters by Latent Dirichlet Allocation algorithm (LDA) and group them into five macro-parameters, namely Generations-Specific Issues, Skills & Qualifications, Employment Sectors, Consumer Industries, and Employment Issues. The journalism approach used in this paper can automatically discover and make objective, cross-sectional, and multi-perspective information available to all. It can bring rigour to journalism by making it easy to generate information using machine learning and can make tools and information available so that anyone can uncover information about matters of public importance. This work is novel since none of the earlier works have reported such an approach and tool and leveraged it to use LinkedIn media for journalism and to discover multigenerational perspectives (parameters) for age dynamics in labour markets. The approach could be extended with additional AI tools and other media.

Hypnotizability is a cognitive trait associated with differences in the brachial artery flow-mediated dilatation of individuals with high hypnotizability (highs) and low hypnotizability scores (lows). The study investigated possible hypnotizability-related cerebrovascular differences. Among 24 healthy volunteers the Stanford Hypnotic Susceptibility Scale Form A, identified 13 medium-to-lows (med-lows), 11 medium-to-highs (med-highs), 1 medium hypnotizable. Hypnotizability did not influence the significant changes produced by the trail making task (TMT), mental arithmetic task (MAT), hyperventilation (HVT) and rebreathing (RBT) on Heart rate (HR), arterial blood pressure (ABP) and partial pressure of end-tidal CO2 (PETCO2) and oxygenation (TOI); but moderated the correlations between the changes occurring during tasks with respect to basal conditions (Δ) in ABP and PETCO2 with MCAv. In HVT, med-lows exhibited a significant correlation between ΔMCAv and ΔPETCO2, med-highs showed a significant correlation between ΔABP and ΔMCAv; a significant correlation between ΔTHI and ΔTOI was observed in medium lows. Cerebrovascular reactivity (CVR) and conductance (ΔCVCi) were significantly correlated with ΔMCAv in med-lows during HVT and RBT. Findings represent the first assessment of hypnotizability-related differences in the mechanisms controlling the middle cerebral artery flow velocity, cerebrovascular reactivity and conductance in response to hyperventilation and rebreathing.

A new subspecies of Sideroxylon mascatense (A.DC.) T.D.Penn. in the Western Hajar Mountains, differing from the type subspecies in the colour of the mature fruit, is described. The two colour forms are genetically isolated, showing that these two are distinct taxa.

Let $G$ be a group with identity $e$ and $R$ be a commutative $G$-graded ring with nonzero unity $1$. Graded semi-primary and graded $1$-absorbing primary ideals have been investigated and examined by several authors as generalizations of graded primary ideals. However, these three concepts are different. In this article, we characterize graded rings over which every graded semi-primary ideal is graded $1$-absorbing primary and graded rings over which every graded $1$-absorbing primary ideal is graded primary.

The ASCE-EWRI reference evapotranspiration (ETo) equation is recommended as a standardized method for reference crop ETo estimation. However, various climate data as input variables to the standardized ETo method are considered limiting factors in most cases and restrict the ETo estimation. This paper assessed the potential of different machine learning (ML) models for ETo estimation using limited meteorological data. The ML models used to estimate daily ETo included Gene Expression Programming (GEP), Support Vector Machine (SVM), Multiple Linear Regression (LR), and Random Forest (RF). Three input combinations of daily maximum and minimum temperature (Tmax and Tmin), wind speed (W) with Tmax and Tmin, and solar radiation (Rs) with Tmax and Tmin were considered using meteorological data during 2003–2016 from six weather stations in the Red River Valley. To understand the performance of the applied models with the various combinations, station, and yearly based tests were assessed with local and spatial approaches. Considering the local and spatial approaches analysis, the LR and RF models illustrated the lowest rate of improvement compared to GEP and SVM. The spatial RF and SVM approaches showed the lowest and highest values of the scatter index as 0.333 and 0.457, respectively. As a result, the radiation-based combination and the RF model showed the best performance with higher accuracy for all stations either locally or spatially, and the spatial SVM and GEP illustrated the lowest performance among models and approaches.

As urban populations and transport demand expand, Pakistani metropolitan centers face traffic congestion and environmental challenges. This research aims to assess carpooling (CP) to alleviate traffic congestion, fuel demand, and pollution. This study was conducted in Islamabad, a fast-growing city with a high percentage of personal cars in Pakistan, to assess the travelers’ perceptions, and public acceptance of CP and determine the effects on traffic congestion, fuel consumption, and CO2 emissions. The investigation of travelers' perceptions towards CP was conducted through a stated preference questionnaire survey. A total of 700 responses from one million population of Islamabad were collected as per Sloven's Formula. SPSS and Smart PLS software were used for data analysis. Various factors influencing peoples’ travel perceptions, mode choice, and tendency to carpool, were categorized to evaluate the relationship between travelers’ perception and the tendency to carpool in the presence of mode choice as a mediating variable. Confirmatory factor analysis was conducted in SMART PLS to refine the number of scale items for each variable. One-way ANOVA, step-wise and mediated multiple regression analysis was conducted in SPSS to check the direct and mediating relationship between different variables. Moreover, the probability of reducing traffic congestion and assessing fuel reduction resulting from CP was also analyzed. The findings imply that travelers’ mode choice acts as a mediator between the relationship between travelers’ perception and tendency to carpool. Furthermore, results predicted that CP might reduce 0.25 million cars on the road, about 33.6% of the total private vehicles. Thereby, saving up to 546,810 barrels per year, about 3.42% of Pakistan's total petrol consumption. The findings of this study could be helpful for transport planners, environmentalists, and policymakers to implement carpool systems. Thus, reducing traffic congestion and harmful CO2 emissions and maintaining a sustainable environment.

Spontaneous parametric downconversion At the heart of all quantum optics experiments is called as Spontaneous parametric downconversion. This is a downconversion process when the output frequency is smaller than the input frequency. The whole process is Spontaneous. Experimentally we have to downconvert the photons and convert them into pairs of a photon. We use the Beta-barium borate(BBO) crystals to downconvert the coming violet-blue laser. We find the maximum number of counts on detectors and their coincidence. When the BBO crystals is well aligned, we find no difference in detecting vertically or horizontally polarized photons because they are orthogonal to each other. Proof of existence of photons We want to investigate the properties and verification of quantization of light. Experimently we want to establish the existence of single photon which shows the grainy-ness of individual photon quantum mechanically and shows wave like behaviour classically. We get the coincidences counts on detectors with addition of detector B’ by using PBS in the path of signal beam. Experimentally we prove the Quantum as well as classical nature of light by the measurement of second-order degree coherence in light g²(0). For classically the g²(0)≥1 and quantum mechanically g²(0)=0.When we add the delay time interval of 1ns after reflected and transmitted photons from PBS signal beam. The delay generator did not create a significant difference in the coincidence counts detection in the value of g²(τ ). Single photon interference and quantum eraser we want to observe the interference by making the single photons pass through the interferometer, and we will see the interference of the single photons. If the light passes through the interferometer, the visibility of the interference pattern to which extent these fringes are observed is dependent on the extent to which the ’which-way’ or ’which-path’ information is available to the experimenter. If the observer knows the information about the ’which-way’ of the light path, then we cannot observe the inference pattern. Because we only can make an interference pattern if we erase the which-way information of the light path. If you erase the information about the’ which-way,’ we can observe a very high interference pattern. We can erase the information about the light path’s ’which-way’ or ’which-path’ by using a polarizer and orienting at 45^o. In this way, we can observe a very high pattern. If we introduce the angle of the polarizer at 0^o or 90^o, we see very low interference.

The gut microbiome offers numerous advantages to the hosts, through a variety of physiological mechanisms like firming up gut integrity or shaping the intestinal epithelium. Studies showed 2172 species are identified and isolated from human beings, ordered into twelve different phyla, of which 93.5% belonged to Bacteroidetes, Firmicutes, Proteobacteria and Actinobacteria. Out of the 12, three phyla are identified. Human microbial communities are affected by the host external factors like dietary patterns, lifestyle factors, antibiotic usage, internal factors gender, host genotype, age and race. To analyze the dysbiosis and bacterial variation in different areas of District Faisalabad 10,000 individuals of age 25–35 years were recruited from the two different rural and urban localities. The oral swab and fecal sample were collected according to prescribed manner. The collected samples from demographically and geographically distinct regions of District Faisalabad were subjected to DNA extraction and quantification. The amplification of 16s rRNA was carried out by PCR and visualized through a transilluminator. The results revealed significant elevated, % abundance of fecal microbial profile Blautia spp, Firmicutes, Ruminococcaceae, in rural population however non-significant difference % abundance of total Bifido, E. coli, Faecali bacteria, total Lactobacillus were identified in both demographically distinct regions. The pathogenic Gamma Protebacteria, Fusobacterium, Campylobacter coli were not detected in both study areas. Out of five orally detected microbial profiles, elevated % abundance of Firmicutes was detected in rural population however non-significant difference was observed in % abundance of total Bifido and E. coli in both populations. Total Lactobacillus and Fusobacterium were not detected in oral sample of both urban and rural population. Conclusively, this research accomplished the potential effects of demographic and geographical induced dysbiosis in the normal microbiome of the oral cavity and intestine that might cause dysbiosis associated disorders.

Fe-(9, 19, 28, 37)wt.% Cr alloys were corroded at 700 and 800 ^oC for 70 h under 1 atm of N₂, 1 atm of N₂/3.2%H₂O-mixed gas, and 1 atm of N₂/3.1%H₂O/2.42%H₂S-mixed gas. The corrosion rate of Fe-9Cr alloy increased with the addition of H₂O, and furthermore with the addition of H₂S in N₂ gas. Fe-9Cr alloy was always nonprotective. In contrast, Fe-(19, 28, 37) wt.%Cr alloys were protective in N₂ and N₂/H₂O-mixed gas because of formation of the Cr₂O₃ layer. They were, however, nonprotective in N₂/H₂O/H₂S-mixed gas because sulfidation dominated to form the outer FeS layer and the inner Cr₂S₃ layer containing some FeCr₂S₄.

A significant increase in persimmon production, combined with a higher percentage of fruits intended for export, led to the need to adapt post-harvest technology to ensure that the fruits reach the end consumer in optimal condition. Persimmon is a climacteric fruit, so the respiratory rate and ethylene production regulate its ripening during storage. Depending on the variety, it can be tart or impatient (initially). During mass harvesting, the pulp of persimmon, regardless of its variety, is usually very hard, but then it softens quickly, which creates problems during transportation. The fruit pulp of tart varieties of persimmon is usually lighter than that of tart varieties, but there are fewer filamentous fibers in the pulp of tart varieties that support its structure, therefore, during post-harvest aging, seedless astringent fruits soften faster than less tart fruits with 1-2 or more seeds. In addition, there are many intermediate varieties that change their food-tasting and technological properties depending on the degree of pollination in a single year. This encourages farmers to adhere to various strategies to reduce post-harvest losses. Persimmons are usually sold fresh or dried in the markets. In this article, we sought to compile an up-to-date and brief overview of the latest achievements in the persimmon drying technique, which may arouse interest among farmers and entrepreneurs seeking to implement their projects in this field of production activity.

Oil spillage over a sea or ocean’s surface is a threat to marine and coastal ecosystems. Spaceborne synthetic aperture radar (SAR) data has been used efficiently for the detection of oil spills due to its operational capability in all-day all-weather conditions. The problem is often modeled as a semantic segmentation task. The images need to be segmented into multiple regions of interest such as sea surface, oil spill, look-alikes, ships and land. Training of a classifier for this task is particularly challenging since there is an inherent class imbalance. In this work, we train a convolutional neural network (CNN) with multiple feature extractors for pixel-wise classification; and introduce to use a new loss function, namely ‘gradient profile’ (GP) loss, which is in fact the constituent of the more generic Spatial Profile loss proposed for image translation problems. For the purpose of training, testing and performance evaluation, we use a publicly available dataset with selected oil spill events verified by the European Maritime Safety Agency (EMSA). The results obtained show that the proposed CNN trained with a combination of GP, Jaccard and focal loss functions can detect oil spills with an intersection over union (IoU) value of 63.95%. The IoU value for sea surface, look-alikes, ships and land class is 96.00%, 60.87%, 74.61% and 96.80%, respectively. The mean intersection over union (mIoU) value for all the classes is 78.45%, which accounts for a 13% improvement over the state of the art for this dataset. Moreover, we provide extensive ablation on different Convolutional Neural Networks (CNNs) and Vision Transformers (ViTs) based hybrid models to demonstrate the effectiveness of adding GP loss as an additional loss function for training. Results show that GP loss significantly improves the mIoU and F1 scores for CNNs as well as ViTs based hybrid models. GP loss turns out to be a promising loss function in the context of deep learning with SAR images.

One of the most concerning global environmental issues is the pollution of agricultural soils by heavy metals (HMs), especially cadmium (Cd), which not only affects human health by taking Cd-containing foods but also impacts the quality of rice. The soil's nitrification and denitrification processes, coupled with the release of volatile organic compounds by plants, raise substantial concerns. The understanding of three aspects of paddy soil under conditions of heavy-metal pollution and water management is currently limited. In this review, we summarized recent literature related to the deleterious effects of Cd on both soil processes related to the N cycle and rice quality, particularly aroma, in different water management practices. Under both continuous flooding (CF) and alternate wetting and drying (AWD) conditions, cadmium (Cd) has been observed to reduce both nitrification and denitrification processes. The adverse effects are more pronounced in continuous flooding (CF) compared to alternate wetting and drying (AWD). Similarly, the alteration in rice aroma is more significant in AWD than in CF. The precise modulation of volatile organic compounds (VOCs) by Cd, remains unclear based on the available literature. Nevertheless, HM accumulation is higher in AWD conditions compared to CF, leading to a detrimental impact on volatile organic compounds (VOCs). The literature concluded that AWD practices should be avoided in Cd contaminated fields to decrease accumulation and maintain the quality of rice. In the future, rhizospheric engineering and plant biotechnology can be used to decrease the transport of HMs from the soil to the plant’s edible parts.