The multidrug resistance transporter NorM is an important drug resistance pump and plays a critical role in multidrug resistance in bacteria and mammals. In this study we carried out molecular dynamics simulation to study the mechanism of Na+ binding and dynamical structures of two long loops in the substrate-releasing process in substrate binding NorM. Our simulation study identified several key residues (D41, E261 D377) along the Na+ binding pathway and a multi-state ion-binding mechanism is proposed based on the simulation study. In this proposed model, the transport of Na+ is a multi-stage process with D41 being the first station for binding to Na+, followed by Na+ binding to the second station E262 and finally to the cation-binding site of E262 and D377. During the transport of Na+, the transmembrane components TM1, TM7 and TM2 are rearranged to facilitate the ion transport as well conformational changes of NorM to a closed state. Further, substrate-bound simulation revealed that Loop3-4 and Loop9-10 control the substrate-releasing process.

A simple model has been used to investigate the nature of chemical order in Na-Pb and Na-Hg liquid binary alloy at 700K and 673K respectively. The energy parameter obtained from the model was used to calculate the concentration dependent mixing properties such as Gibb’s free energy of mixing, Concentration fluctuations in the long wavelength limit and the Warren-Cowley chemical short range order parameter. Results obtained showed that both alloys are hetero-coordinated throughout the entire concentration and there is tendency for segregation and demixing to take place in the liquid alloys. We observed that Na-Hg liquid alloy is more strongly interacting binary alloy and chemically ordered than Na-Pb liquid alloy.

The excessive intake of sodium (Na) and insufficient intake of potassium (K) are major concerns to prevent hypertension. Using low-Na/K seasonings (reducing 25% of the NaCl and adding K salt) may improve the dietary Na/K ratio and help prevent hypertension. To devise an intervention study using low-Na/K seasonings at a company cafeteria, we calculated the Na and K contents of the meals served at the cafeteria and estimated changes in the intakes when suitable low-Na/K seasonings were used. We also considered using milk as a good source of K. We used an ingredient list of a company cafeteria and calculated Na and K contents in each dish. The average amounts of NaCl and K per use were 5.04 g and 718 mg, respectively. Seasonings contributed 70.9% of the NaCl. With the use of low-Na/K seasonings, an estimated reduction in NaCl of 0.8 g/day and an estimated increase in K of 308 mg/day was achieved. An additional serving (200 mL) of milk, NaCl was reduced by 0.57 g/day and K was increased by 610 mg/day, with an overall decrease in the dietary Na/K ratio from 3.20 to 2.40. The use of low-Na/K seasonings and dairy may improve the dietary Na/K ratio among cafeteria users and help prevent hypertension.

The aim of the present study was to investigate whether chronic undernutrition modifies the response to rostafuroxin in juvenile rats. Chronic undernutrition was induced in male rats using a multideficient diet known as Regional Basic Diet (RBD), mimicking alimentary habits in impoverished regions worldwide. Animals were given RBD – or a control/CTRL normal diet for rodents – from weaning to 90 days, and rostafuroxin (1 mg/kg body mass) or vehicle were orally administered during the last 30 days. Undernourished rats became hypertensive at 55–60 days of age (tail-cuff recording). During the last two days, the rats were hosted in metabolic cages to measure food/energy, water, Na+ ingestion, and urinary volume. Blood and kidneys were collected after euthanasia. Rostafuroxin increased food/energy and Na+ intake in CTRL and RBD rats but had opposite effects on Na+ balance (intake minus urinary excretion): negative in CTRL and positive in RBD. The drug normalized the decreased plasma Na+ concentration found in RBD rats, increased urinary volume in RBD but not in CTRL, and decreased and increased urinary Na+ concentration in the RBD and CTRL groups, respectively. Rostafuroxin decreased the ouabain-sensitive (Na++K+)ATPase and increased the ouabain-resistant, furosemide-sensitive Na+-ATPase from proximal tubule cells in both groups, and normalized the systolic blood pressure in RBD without effect in CTRL rats. We conclude that chronic undernutrition modifies the response of blood pressure, caloric metabolism, Na+ distribution in liquid compartments, mobilization of Na+ from non-osmotic compartments, Na+ and water balance, and activity of renal Na+-transporting ATPases to rostafuroxin.

Background: Despite tremendous efforts to reduce neonatal mortality worldwide and in 24 Ethiopia, there is the country is one of the countries with highest neonatal morbidity and health 25 losses. Never the less, the past three decades’ national trend and subnational distribution of 26 neonatal morbidity and mortality and its health loss in Ethiopia, was not well documented. 27 Hence, this study had aimed to analyze the trend and distributions as well as health losses 28 resulting from neonatal morbidity in the past three decades in Ethiopia, 2019. 29 Objective: To assess the national trend and sub national distributions of neonatal morbidity and 30 neonatal mortality in the previous three decades by using Global Burden of Diseases, 2019 data. 31 Methods: The data sources were primary and secondary data related to risk factors, morbidity, 32 disability, deaths, Disability Adjusted Life Years, Years Lived with Disability and Years Life Lost 33 were collected form case studies and case series, household surveys, socio-demographic surveys 34 and surveillances, health facilities surveys, Health facility observations and interviews and 35 published and unpublished literatures. The prevalence, deaths and health losses were calculated 36 by using embedded model. The study period covered from 1990 to 2019. Results were presented 37 buy using texts, tables and graphs. 38 Results: Seventy percent of neonatal disorders had occurred among early neonates aged 0 to 6 39 days. Between 1990 and 2019, the national prevalence of neonatal disorders had increased by 40 47% in to 28,319 (95% UI, 25646-30,361). Bet Similarly, the highest number of neonatal deaths 41 caused by neonatal sepsis had shifted from Southern Nations Nationalities and Peoples region to 42 Oromia region while Harari remains to bear the lowest burden in the last three decades. The 43 highest and the lowest YLL as a result of neonatal disorders had occurred in Oromia 44 [(2,753,038,95% UI, 2,184,142-3,497-926) and Amhara 1,360,847 [(95% UI, 95% UI, 45 1,062,660-1,762,028)] regions respectively. Unlike other regions, Addis Ababa had the highest 46 (52%) prevalence of preterm birth in 2019 47 Conclusion and Recommendation: About seven in ten of neonatal death had occurred among 48 early neonates indicating narrowed occurrence of the event. The highest and the lowest number 49 of neonatal death and health loss had occurred in Oromia and Harari regions respectively. The 50 main causes of death were neonatal sepsis and other infections, neonatal preterm, hemolytic 51 disease and other jaundice and neonatal encephalopathy and trauma. Hence, Contextualized, 52 locally accepted innovative early neonatal care is crucial to avert the event.

The recent remarkable progress in Artificial Intelligence (AI) has renewed the discussion on the possibility of human-level AI. Despite the difficulty of the problem and the presence of many large gaps and challenges, most people working in the field think that human-level AI is achievable, but they disagree on the date. In this paper, I briefly discuss the possibility of human-level AI from the perspective of two traditions in the Islamic world, namely Kalam and Sufism, and despite their different mode of investigation, they converge to the same conclusion on this topic.

The atomic structures of Zn and Na borophosphate glasses were studied by X-ray and neutron diffraction. Peaks assigned to the B−O, P−O, and O−O distances confirm that only BO4 units co-exist with the PO4 tetrahedra. The Zn−O and Na−O coordination numbers are found to be a little larger than four. The narrowest peaks of the Zn−O first-neighbor distances exist for the glasses along a line connecting the Zn(PO3)2 and BPO4 compositions (50 mol% P2O5) which is explained by networks of ZnO4, BO4, and PO4 tetrahedra with twofold coordinated oxygens. Calculated amounts of the available oxygen support this interpretation. Broadened peaks occur for glasses with lower P2O5 contents, consistent with the presence of threefold coordinated oxygens. The two distinct P−O peak components of the Zn and Na borophosphate glasses differ in their relative abundances which is interpreted by Na+ cations that coordinate oxygens in some P−O−B bridges, something not seen for the Zn2+ ions.

(1) Background: Sentinel lymph node (SLN) mapping represents an accurate and feasible technique for the surgical staging of endometrial and cervical cancer. This is commonly performed by conventional laparoscopy or robotic-assisted laparoscopy, but in recent years, a new retroperitoneal transvaginal natural orifice transluminal endoscopic surgery (vNOTES) approach has been described. This technique provides easy visualization of lymphatic afferent vessels and pelvic lymph nodes, early SLNs assessment, and a coherent mapping methodology following the lymphatic flow from caudal to cranial. However, only a few publications have reported it. Following the IDEAL (Idea Development Exploration Assessment Long-term follow-up) framework, research concerning this technique is at stage 2a, with only small case series as evidence of its feasibility. Its standardized description appears necessary to provide the surgical homogeneity required to move further. (2) Methods: description of a standardized approach for retroperitoneal pelvic SLN mapping by vNOTES. (3) Results: we described a 10-step approach to successfully perform retroperitoneal vNOTES SLN mapping, including pre-, intra-, and postoperative management. (4) Conclusions: This IDEAL stage 2a study could help other surgeons approach this new technique, and it proposes a common methodology necessary to evolve through future IDEAL stage 2b (multi-center studies) and stage 3 (randomized controlled trials) studies.

The Shisa family is a type of single-transmembrane adaptor proteins containing an N-terminal cysteine-rich domain and a proline-rich C-terminal region. Nine Shisa subfamily genes have been proposed in most vertebrates; however, some of them might be species-specific. The number of Shisa genes present in zebrafish remains unclear. The purpose of this study was to investigate the evolutionary relationships among Shisa family genes in zebrafish (TU strain) using phylogenetic and syntenic analyses. The function of shisa-2 was preliminarily examined via CRISPR/Cas13d-mediated knockdown. Following identification in zebrafish,10 Shisa family genes, namely shisa-1, 2, 3, 4, 5, 6, 7, 8, 9a, and 9b, were classified into three main clades and six subclades. Their encoding proteins contained a cysteine-rich N-terminal domain and a proline-rich C-terminal region containing different motifs. A specific syntenic block containing atp8a2 and shisa-2 was observed to be conserved across all species. Furthermore, all these genes were found to be expressed during embryogenesis. shisa-2 was expressed in the presomitic mesoderm, somites, and so on. shisa-2 was identified as a regulator of the expression of the somite formation marker mesp-ab. Overall, our study provides new insights into the evolution of Shisa family genes and the control of shisa-2 over the convergent extension cells of somatic precursors in zebrafish.

The initiation reactions of DNA synthesis are central processes during human chromosomal DNA replication. They are separated into two main processes: the initiation events at replication origins, the start of the leading strand synthesis for each replicon, and the numerous initiation events taking place during lagging strand DNA synthesis. In addition, a third mechanism is the re-initiation of DNA synthesis after replication fork stalling, which takes place when DNA lesions hinder the progression of DNA synthesis. The initiation of leading strand synthesis at replication origin is regulated at multiple levels, from the origin recognition to the assembly and activation of replicative helicase, the Cdc45-MCM2-7-GINS (CMG) complex. In addition, the multiple interactions of the CMG complex with the eukaryotic replicative DNA polymerases such as DNA polymerase α-primase (Pol α), DNA polymerase δ and ε at replication forks play pivotal roles in the mechanism of initiation reactions including the initiation of signalling unperturbed and stalled replication forks, ‘replication stress’ events, via ATR (ATM-Rad 3-related protein kinase). All these processes are essential for the accurate transfer of the cells’ genetic information to their daughters. Failures and dysfunctions in these processes gives rise to genome instability followed by genetic diseases including cancer. Thus, in their review ‘Hallmarks of Cancer: New Dimensions‘ Hanahan and Weinberg (2022) called genome instability a fundamental function in the development process of cancer cells. In recent years, the understanding of the initiation processes and mechanisms of human DNA replication has made substantial progress at all levels which will be discussed in the review.

Smart City has emerged as the mainstream paradigm for urban governance innovation, sustainable development, and strategy upgrades, which is drawing attention from scholars worldwide. However, current frameworks for Smart City assessment remain incomplete and simplistic. In is paper, 30 national or provincial capitals in China were selected and we designed a tri-dimensional SPI model—Social, Physical, and Information Space—for smart city spatial development assessment. Utilizing methods such as entropy weighting, coupled coordination degree models, and the Dagum Gini coefficient, this study assesses the spatial development and coupled coordination of 30 cities from 2011 to 2019. Finally, by means of BP neural networks, the study examines the contribution of each indicator to the spatial coupled coordination. The results indicated that with a narrowing disparity in development speeds among different regions, the spatial coupled coordination development level of smart capitals in China has steadily increased, presenting a pattern of staggered distribution. Moreover, the IS subsystem plays the most significant role in coupled coordination. The significance of this research lies in its tri-dimensional spatial perspective of the spatial development and coupled coordination differences of the Smart City, providing evidence-based support for the regional layout and optimization in China.

Silybin is a natural compound extensively studied for its hepatoprotective, neuroprotective and anti-cancer properties. Envisioning the enhancement of silybin potential by suitable modifications in its chemical structure, here, a series of new 7-O alkyl silybins derivatives were synthesized by Mitsunobu reaction starting from the silybins and tyrosol-based phenols, such as tyrosol (TYR, 3), 3-methoxytyrosol (MTYR, 4) and 3-hydroxytyrosol (HTYR, 5). This research sought to explore the antioxidant and anticancer properties of new eighteen derivatives and their mechanisms. In particular, the antioxidant properties of new derivatives outlined by DPPH assay, showed a very pronounced activity depending on the tyrosyl moiety (HTYR>MTYR>>TYR). A significant contribution of the HTYR moiety was observed for silybins and 2,3-dehydro-silybin based derivatives. According to the very potent antioxidant activity, 2,3-dehydro-silybin derivatives 15ab, 15a and 15b exerted the most potent anticancer activity in human prostate cancer PC-3 cells. Furthermore, flow cytometric analysis for cell cycle and apoptosis revealed that 15ab, 15a and 15b induce strong G1 phase arrest and increase late apoptotic population in PC-3 cells. Additionally, western blotting for apoptotic marker cleaved caspase-3 confirmed apoptosis induction by these silybin derivatives in PC-3 cells. These findings hold significant importance in the investigation of anticancer properties of silybin derivatives and strongly encourage swift investigation in pre-clinical models and clinical trials.

Various wood fibres, including pine and flax, are used in wood–plastic composites (WPCs). This paper studies the effect of the lignin content on the morphological and thermal degradation and damage due to the ultraviolet (UV) aging of polypropylene/flax (PP-flax) and polypropylene/pine (PP-pine) fibres composites. Flax and pine fibres exhibited distinct densities of 1.51 and 1.47 g/cm³, respectively, potentially influenced by growth factors and varying compositions of light substances, such as hemicellulose, lignin, and impurities. The thermal decomposition mass loss increased proportionally with the percentage of lignin in the fibre. From 238°C to 390°C, the pine fibre exhibited a 72% mass loss compared to flax fibre, which showed a 54% mass loss, owing to the higher lignin content in pine fibres. Based on differential scanning calorimetry (DSC), the fibre composition affected the material melting temperature. Moreover, DSC curves revealed a higher degree of crystallinity in the case of the PP-flax biocomposite (12%) compared to pure polypropylene (9%) and PP-pine (6%). This result can be attributed to the high content of crystalline components in flax fibres, such as cellulose. Acoustic emissions analysis confirmed that the high lignin content delays degradation and mitigates the appearance of microcracks on the surface of the PP-pine biocomposite. Overall, the study provides valuable data for understanding the UV degradation phenomenon in biocomposites and highlights the influence of fibre composition on material performance.

The rapid retreat of coastal cliffs poses a profound risk to property, transport infrastructure and public safety both in Ireland and globally. This study combines historical data (maps and orthophotos, 1842 to 2000) with contemporary UAV surveys (2019 to 2023) to quantify cliff top and cliff face retreat along a 250 m wide coastal drumlin at Silverstrand in Galway Bay, Ireland. Retreat rates for the cliff top and cliff face were calculated using 2D mapping and 3D modelling, respectively. Critically, the choice of method appears to have a major impact on apparent rates of cliff top retreat, with output from the 2D mapping approach (0.14 +/- 0.02 m yr-1) being double that of the 3D modelling approach (0.08 +/- 0.02 m year-1). The aperiodic development of a talus cone, which offers temporary protection to the cliff from storm waves, also influences the estimation of cliff retreat. The repeat cycles of talus slope formation and removal in this high wave energy climate suggest that the drumlin transitions between a periodically transport-limited system and supply limited system over short- and long-time periods, respectively, on the continuum of cliff types. These results warrant further research to identify and quantify the rates, patterns, drivers (marine and subaerial processes), and timing of cliff retreat rates in response to climate change.

The Na+/K+ ATPase is a protein involved in the active transport of ions across the cellular membrane. Ouabain is a cardiotonic glycoside that, by inhibiting the Na+/K+ pump, interferes with cell processes mediated directly by the pump, but also indirectly influences other cellular processes, such as cellular cycle and proliferation, growth, cell differentiation, angiogenesis, migration, adhesion and invasion. We used the SK-BR-3 breast cancer cell line, mesenchymal stem cells (MSCs), and tumor-associated fibroblasts (TAFs) in vitro for determining the changes induced by Ouabain in concentration of 10-5 M, 10-6 M, 10-8 M, 10-9 M on these cellular types, employing specific methods: SEM for morphological evaluation; immunocytochemistry, flowcytometry to assess immunophenotypical markers expression, cell cycle and Annexin V/PI assay for cellular proliferation and viability testing; flowchamber assay to evaluate functional adhesion behavior; RT-PCR for Na+/K+ ATPase subunits molecular expression. Being indicative of the pro-apoptotic and inhibitory effect of Ouabain on tumor invasion and metastasis, the results support the addition of Ouabain to the oncological therapeutic arsenal, trailing the “repurposing drugs” approach.

The concern about consuming eco-friendly products has motivated research in the development of new materials. Therefore, films based on natural polymers have been used to replace traditional polymers. This study consists of a production of films based on gelatin reinforced with black pepper essential oil-loaded nanoemulsions and Cloisite Na⁺. The films were characterized by water vapor permeability, mechanical and thermal properties, surface contact angle, X-ray diffraction and scanning electron microscopy. It was observed that the films containing the nanoemulsion have higher permeability values and an increase in their mechanical resistance. The addition of nanoclay contributed to an increase in the surface hydrophobicity of the film and an increase in the tensile strength at break by about 150%. The addition of essential oil nanoemulsions led to an increase in thermal stability. The presence of clay dispersion contributed to the formation of a surface that was slightly rougher and grainier. The addition of the black pepper essential oil nanoemulsion resulted in an increase in porosity of the gelatin matrix. Through X-ray diffraction analysis, it was possible to conclude that both the polymeric gelatin matrix and the essential oils nanoemulsion are intercalated with the clay dispersion.

Although the signaling function of Na/K ATPase is been studied for decades, the chasm between the pumping function and the signaling function of Na/K – ATPase is still an open issue. This article explores the relationship between ion pumping and signaling with attention to the amplification of oxidants through this signaling function. Starting with some experimental observations published by our laboratories and others, we develop some predictions regarding cellular oxidant stress.

Na⁺/H⁺ exchangers (NHEs) are known to be important regulators of pH in multiple intracellular compartments of eukaryotic cells. Sperm function is especially dependent on changes in pH and thus it has been postulated that NHEs play important roles in regulating the intracellular pH of these cells. For example, in order to achieve fertilization, mature sperm must maintain a basal pH in the male reproductive tract and then alkalize in response to specific signals in the female reproductive tract during the capacitation process. Eight NHE isoforms are expressed in mammalian testis/sperm: NHE1, NHE3, NHE5, NHE8, NHA1, NHA2, NHE10, and NHE11. These NHE isoforms are expressed at varying times during spermatogenesis and localize to different subcellular structures in developing and mature sperm where they contribute to multiple aspects of sperm physiology and male fertility including proper sperm development/morphogenesis, motility, capacitation, and the acrosome reaction. Previous work has provided evidence for NHE3, NHE8, NHA1, NHA2, and NHE10 being critical for male fertility in mice and NHE10 has recently been shown to be essential for male fertility in humans. In this article we review what is known about each NHE isoform expressed in mammalian sperm and discuss the physiological significance of each NHE isoform with respect to male fertility.

Under batch experiment conditions, this work seeks to successfully remove Diclofenac-Na (DCF-Na) from an aqueous solution utilizing a composite sorbent made of Bentonite, Kaolinite clay, and Worm casting (BKW). This study investigated the structural modification of the H₃PO₄ Modified Clay by X-ray fluorescence and the effect of selected adsorption factors – DCF-Na concentration and modified BKW composite dosage. The concentration equilibrium data was used to study six isotherm models. Freundlich isotherm model better explained the adsorption of DCF-Na onto modified BKW composite with a correlation coefficient close to 1. Kinetics models were examined, and the Elovich model gave a better fit than other kinetic models studied. Mass diffusion mechanisms and thermodynamics studies were successfully carried out. The enthalpy change values evaluated were negative, which revealed the spontaneity of DCF-Na remediation onto modified BKW, and that DCF-Na adsorption is exothermic and occurred through a physisorption process.

Employing remote sensing techniques to evaluate crop residue cover (CRC) enables rapid mapping of tillage practices over large cropland areas, which has significant practical implications for monitoring the implementation of conservation tillage practices. This research utilized Sentinel-2 MSI and Landsat-8 OLI remotely sensed data, various spectral indices were calculated and the datasets were correlated with the field-measured CRC data. Selected spectral indices, highly significantly correlated, were chosen to build a correlation model between the indices and the CRC. Considering Sentinel-2 MSI and Landsat 8 OLI remotely sensed data variations in spectral and spatial scales, the accuracy of CRC models was evaluated using R2 and RMSE values. From the results, it's evident that all six spectral indices, including STI, NDTI, SRNDR, NDI5, NDI7 and NDSVI, registered correlation coefficients with the CRC exceeded 0.3 in the study area. STI and NDTI showed a stronger correlation to CRC, with coefficients of 0.810 and 0.803, respectively. For the Landsat 8 data, the lowest correlation obtained was for NDSVI with the Landsat 8 data with a correlation coefficient of 0.358. Applying the linear regression technique, STI and NDTI obtained higher accuracy compared to other indices in the Sentinel-2 MSI data. For NDTI and STI, The R2 values were 0.650 and 0.665, respectively, while their corresponding RMSE values were 3.96% and 4.03%. The highest model accuracy was obtained for the STI and NDTI constructed from the Landsat 8 OLI data (R2 values 0.41 and 0.40; RMSE values 5.25% and 5.27%, respectively). The CRC model built using partial least squares regression (PLSR) exhibited greater precision when applied to the Sentinel-2 MSI data (R2 value 0.894; RMSE value 2.18%) in comparison to the Landsat 8 OLI data (R2 value 0.695; RMSE value 3.70%). PLSR has the potential to enhance the precision of the model. In addition, the study area shows that the estimation of the CRC is better in the one-dimensional linear regression model and the PLSR model created with the Sentinel-2 MSI optical data compared to the Landsat 8 OLI optical remotely sensed data. The validation suggests that the CRC estimation in the study area is more precise when using the model relying on Sentinel-2 satellite imagery rather than the Landsat 8 OLI imagery.

Fluorescent bioprobes are invaluable tools for visualizing live cells and deciphering complex biological processes by targeting intracellular biomarkers without disrupting cellular functions. In addition to protein-binding concepts, fluorescent probes utilize various mechanisms, including membrane, metabolism, and gating-oriented strategies. This study introduces a novel fluorescent mechanism distinct from existing ways. Here, we developed a B-cell selective probe, CDrB, with unique transport mechanisms. Through SLC-CRISPRa screening, we identified two transporters, SLCO1B3 and SLC25A41, by sorting out populations exhibiting higher and lower fluorescence intensities, respectively, demonstrating contrasting activities. We confirmed that SLCO1B3, with comparable expression levels in T and B cells, facilitates the transport of CDrB into cells, while SLC25A41, overexpressed in T lymphocytes, actively exports CDrB. The observation suggests that SLC25A41 plays a crucial role in discriminating between T and B lymphocytes. Furthermore, it reveals the potential for reversible localization of SLC25A41 to demonstrate its distinct activity. This study is the first report to unveil a novel strategy of SLC by exporting the probe. We anticipate that this research will open up new avenues for developing fluorescent probes.

With the economic recession and the deterioration of the ecological environment becoming more and more prominent in the world, the sustainable operation of enterprises is facing the most difficult choice in history. For each responsible enterprise, it is crucial to choose the market power expansive strategy that can improve the realistic viability or the technological innovation strategy that can improve the future development potential. This is of great significance to reduce the negative external effects of the corporate social environment and ensure their sustainable development. In this paper, we select the data of 18 large listed petrochemical companies from 2003 to 2018 as samples and construct a linear regression model for empirical analysis. Meanwhile, we put forward more practical business management strategies for the sustainable development of petrochemical enterprises in developing countries in further research.

In this study, we use descriptive statistics and data visualization techniques to analyze datasets and identify patterns and relationships between bikeshare and other transportation modes. We also use regression analysis to quantify the impact of various factors on bikeshare usage. Our results indicate that bikeshare trips during the pandemic were much longer compared to pre-pandemic times. Moreover, usage of bikeshare differed by user group, with casual users showing a greater increase in usage compared to subscribers. We plotted bivariate choropleth maps to visualize the spatial distribution of changes in bikeshare usage. Our findings suggest that an increase in bikeshare travel was associated with a reduction in travel by ride-hailing and public transit, especially in the northern part of the city, indicating a potential replacement of other modes of transportation. On the western and southern boundary of the city, bikeshare had a complementary effect with other modes. Overall, the data acquired for this study provides a valuable opportunity to understand the behavior of bikeshare users in Chicago, the intercorrelation of bikeshare with other transportation modes, and the impact of infrastructure on bikeshare usage. The findings of this study can inform the design and implementation of bikeshare systems in other cities and contribute to the development of a more sustainable transportation system.

In the development of the safety-critical systems, it is important to perform Failure Modes and Effects Analysis (FMEA) process to identify potential failures. However, traditional FMEA activities tend to be considered difficult and time-consuming tasks. To compensate for the difficulty of the FMEA task, various types of tools are used to increase the quality and the effectiveness of the FMEA reports. This paper explains an Automatic FMEA tool which integrates the Model-based Design (MBD), FMEA, and Simulated Fault Injection techniques in a single environment. The Automatic FMEA tool has the following advantages compared to the existing FMEA analysis tool. First, the Automatic FMEA tool automatically generates FMEA reports compared to the traditional spreadsheet-based FMEA tools. Second, the Automatic FMEA tool analyzes the causality between the failure modes and the failure effects by performing model-based fault injection simulation. In order to demonstrate the applicability of the Automatic FMEA, we used the electronic fuel injection system (EFI) Simulink model. The results of the Automatic FMEA were compared to that of the legacy FMEA.

Amid escalating urbanization, devising rational commercial space layouts is a critical challenge. Leveraging machine learning, this study uses a Back-propagation (BP) neural network to optimize commercial spaces in Weinan City's central urban area. The results indicate an increased number of commercial facilities with a trend of multi-centered agglomeration and outward expansion. Based on these findings, we propose a strategic framework for rational commercial space development emphasizing aggregation centers, development axes, and spatial guidelines. This strategy provides valuable insights for urban planners in small and medium-sized cities in the Yellow River Basin and metropolitan areas, ultimately showcasing the power of machine learning in enhancing urban planning.

(1) Background: in the context of sustainable development goals (SDGs), this work explores the repair direction of future cultivated land protection policies based on the Smith policy implementation model from the historical evolution to ensure that the cultivated land protection policy does not deviate during the implementation process. (2) Methods: this paper uses literature research and inductive deduction methods to sort out the evolution process of Chinese cultivated land protection policy, summarize the successful experience of transferring the focus of cultivated land protection in chronological order, and conclude the repair direction of Chinese cultivated land protection. (3) Results: although the Chinese cultivated land protection policy in the historical evolution has through three significant phases, there are still certain issues in the development trend of Chinese cultivated land protection policy based on regional division of labor for grain transportation and sales. (4) Conclusion: directly utilizing feedback from farmers as stakeholders will contribute to the maturity and improvement of cultivated land protection policies in the specific implementation of cultivated land protection policies.

Since the discovery of graphene, due to its excellent optical, thermal, mechanical and electrical properties, it has a broad application prospect in energy, materials, biomedicine, electromagnetism and other fields. A great quantity of researches on the physical mechanism of graphene has been applied to engineering in electromagnetism and optics. To study the properties of graphene, different kinds of numerical methods have been developed for simulating the electromagnetic field effects of graphene, and equivalent boundary conditions have been employed to replace graphene in the computational domain. In this work, the numerical methods with equivalent boundary conditions are reviewed, and some examples are provided to illustrate their applicability.

Significant amounts of anthropogenic radionuclides were introduced in ocean waters following nuclear atmospheric tests and development of the nuclear industry. Dispersion of artificial dissolved radionuclides has been extensively measured for decades over the European continental shelf. The radionuclide measurement and release fluxes databases provided here represent an exceptional opportunity to validate dispersion hydrodynamic models. MARS hydrodynamic model have been applied at different scales to reproduce in realistic conditions the measured dispersion. Specific methods have been developed to obtain qualitative and quantitative results and perform model/measurement comparisons. Model validation concerns short to large scales with dedicated surveys following the dispersion: it was performed within two and three dimensions framework and from minutes and hours following a release up to several years. Results are presented concerning the dispersion of radionuclides in marine systems deduced from standalone measurements, or according to model comparisons. It allows characterising dispersion over the continental shelf, pathways, transit times, budgets and source terms. This review exhibits the main features retained from the point of view of radiotracers, hydrodynamic models and model/measurement methods with perspectives of applications in other areas or oceanographic domains.

Achieving the dual development of rural revitalization and urbanization is an important strategic goal of China’s current modernization. Rural population and settlements are the main components of the countryside in traditional agricultural areas, and play an important role in the development of the countryside itself in terms of urban and rural land use and in the formation of urban and rural development patterns. This study analyzes the spatial and temporal changes in rural populations and settlements at the township level, as well as the degree and type of coupled development. A framework for urban–rural development relationships based on different types of coupled development is proposed, and a model of urban–rural forces is constructed to derive the spatial pattern of urban–rural development at the township level that may be formed in the future. Our study shows that the rural population and settlements in the study area are characterized by significant spatial and temporal dynamics, indicating that traditional rural areas are in a process of rapid development and change. The results of the township-level coupling measurements present four types of development in terms of the spatial pattern of urban–rural development: A-type is most likely to produce new cities or satellite towns in the Jixi–Harbin–Qiqihar area in the future; B-type is the fastest dying area in the future, located in the Harbin and Qitaihe clusters, with a tendency to merge into Harbin; C-type is the area to be focused on in the future to attract population and strictly control the growth of the rural settlement area to avoid it turning into B-type; D-type may develop regional township centers in the future in the combined area of Jiamusi City, Suihua City and Mudanjiang City. The results of the study provide experience in realizing rural revitalization according to local conditions. The new spatial pattern of urban–rural development provides an important reference for formulating land use policies, optimizing urban–rural land allocation and realizing integrated urban–rural development strategies.

Health of migrant is a widely studied topic. It has been argued that migrant health may deteriorate over time. Though migrants are ‘a hard to reach’ population in survey data, this paper builds on a unique dataset provided by Médecins du Monde from five countries. We study self perceived health (SPH) in connection with socio-economic and demographic factors and length of stay. Results show different results for men and women. Asylum seekers compared to other documented migrants have a worse health. Migrants with better living conditions tend to be in better health. Employment and stable accommodation has a positive effect on SPH. Women from poorer countries have a better physical SPH after 3 months of residing in the host country. This paper contributes widely to knowledge of health of migrants. Contrarily to other evidence, health of migrants tends to improve for some migrants.

Government support plays an important role in Chinese economy. New energy industries, concerning innovation-driven source and environmental protection, are also supported by government. This paper aims to study the effects of the traditional government support at supply side on firms’ innovation and development. In this paper, we propose enterprise behavior model including characteristics of new energy industries, and study the innovation reaction of firms to government support in different situation. We further use propensity score matching to verify the results in theoretical model, and conduct robustness analysis. Our main conclusions include: (1) In the normal years government support can only promote the innovation output of firms which have innovated, however, can not promote the innovation probability of firms which have not innovated. That is to say, government support can only enhance the intensive margin of innovation, but can not enhance the extensive margin of innovation with less competition. (2) In the situation of bad economic environment and intense competition, firms’ innovation probability rises as the government support increase. Therefore, government should provide more R&D special subsidies and implement strict financial supervision to make the effectiveness of support policies especially in the normal years.

Plants have developed unique mechanisms to cope with the harsh environmental conditions to compensate for their lack of mobility. A key part of their coping mechanisms is the synthesis of secondary metabolites. In addition to their role in plants’ defense against pathogens, they also possess therapeutic properties against diseases, and their use by humans predates written history. Viruses are a unique class of submicroscopic agents, incapable of independent existence outside a living host. Pathogenic viruses continue to pose a significant threat on global health, leading to unprecedented fatalities on a yearly basis. The use of medicinal plants as a natural source for an-tiviral agents has been widely reported in literature in the past decades. Metabolomics is a powerful research tool for the identification of plant metabolites with antiviral potentials and can be used to isolate compounds with antiviral activities in plants and study the biosynthetic pathways involved in viral disease progression. This review discusses the use of medicinal plants as antiviral agents, with a special focus on the metabolomics evidence supporting their efficacy. Additionally, suggestions are made for the optimization of various metabolomics methods for characterizing the bio-active compounds in plants and subsequent understanding of the mechanism of their operation.

Monascus pigments (MPs) have been used as food colorants for several centuries in Asian countries and nowadays in the whole world via Asian catering. The MPs biosynthetic pathway has been well-illustrated, however, the functions of a few genes including mrpigH in the MPs gene cluster of M. ruber M7 are still unclear. In current study, mrpigH was disrupted in Δmrlig4ΔmrpyrG, a highly efficient gene modification system, using mrpyrG as a selection marker, and ΔmrpigHΔmrlig4ΔmrpyrG::mrpyrG and ΔmrpigHΔmrlig4ΔmrpyrG have been obtained. Subsequently, their morphologies, biomasses, MPs and citrinin (CIT) production were analyzed, respectively. These results have revealed that the deletion of mrpigH has significant effects on the morphology and growth of M. ruber M7. Moreover, compared with M. ruber M7, the yields of MPs and CIT were drastically increased and decreased in mrpigH mutants, respectively.

Receptor-interacting protein kinase 1 (RIPK1) plays a crucial role in controlling inflammation and cell death. Its function is tightly controlled through post-translational modifications, enabling its dynamic switch between promoting cell survival and triggering cell death. Phosphorylation of RIPK1 at various sites serves as a critical mechanism for regulating its activity, exerting either activating or inhibitory effects. Perturbations in RIPK1 phosphorylation status have profound implications for the development of severe inflammatory diseases in humans. This review explores the intricate regulation of RIPK1 phosphorylation and dephosphorylation and highlights the potential of targeting RIPK1 phosphorylation as a promising therapeutic strategy for mitigating human diseases.

The aim of the present study was to investigate whether chronic undernutrition modifies the response to rostafuroxin in juvenile rats. Chronic undernutrition was induced in male rats using a multideficient diet known as Regional Basic Diet (RBD), mimicking alimentary habits in impoverished regions worldwide. Animals were given RBD – or a control/CTRL normal diet for rodents – from weaning to 90 days, and rostafuroxin (1 mg/kg body mass) or vehicle were orally administered during the last 30 days. Undernourished rats became hypertensive at 55–60 days of age (tail-cuff recording). During the last two days, the rats were hosted in metabolic cages to measure food/energy, water, Na⁺ ingestion, and urinary volume. Blood and kidneys were collected after euthanasia. Rostafuroxin increased food/energy and Na⁺ intake in CTRL and RBD rats but had opposite effects on Na⁺ balance (intake minus urinary excretion): negative in CTRL and positive in RBD. The drug normalized the decreased plasma Na⁺ concentration found in RBD rats, increased urinary volume in RBD but not in CTRL, and decreased and increased urinary Na⁺ concentration in the RBD and CTRL groups, respectively. Rostafuroxin decreased the ouabain-sensitive (Na⁺+K⁺)ATPase and increased the ouabain-resistant, furosemide-sensitive Na⁺-ATPase from proximal tubule cells in both groups, and normalized the systolic blood pressure in RBD without effect in CTRL rats. We conclude that chronic undernutrition modifies the response of blood pressure, caloric metabolism, Na⁺ distribution in liquid compartments, mobilization of Na⁺ from non-osmotic compartments, Na⁺ and water balance, and activity of renal Na⁺-transporting ATPases to rostafuroxin.

Diabetic kidney disease (DKD) is the major cause of chronic kidney disease (CKD) and increases the risk of cardiovascular events. Hemodynamic, inflammatory and metabolic factors, which share the convergent pathway of fibrosis, are considered to involve in the pathogenesis of DKD. In spite of the emerging of angiotensin receptors blockers (ARBs)/ angiotensin converting enzyme inhibitor (ACEI), sodium-glucose cotransporter 2 (SGLT2) inhibitors, and nonsteroidal mineralocorticoid receptors antagonists (NS-MRAs), current therapies still couldn’t arrest the progression of DKD. Glucagon like peptide 1 receptor agonists (GLP-1RAs) are promising agents to play renoprotective roles in slowing the progression of DKD. Based on the treatment of heart failure, combined use of drugs is recommended for DKD rather than single use. Unearthing the mechanisms underlying DKD is urgent to investigate the management of DKD. Here, we elaborate on the potential mechanisms and the current therapies of DKD. We also discuss the additional value of the combined use of these drugs for DKD to establish novel concepts of treatment.

Inflammation is known to be risk factors for metabolic diseases. The purpose of this study was to develop a Food-based Index of Dietary Inflammatory Potential (FBDI) and conduct its validation assessment. This study analyzed raw data from Korean Genome and Epidemiology Study 2012–2014 data of 17,771 people. We carried out the correlation analysis between 51 food groups and hs-CRP. The FBDI was developed by multiple regression method with hs-CRP and selected 17 food group. For the validation of FBDI, 7795 people in the 6th Korea National Health and Nutrition Examination Survey (KNHAES) was used. Binary logistic regression analysis was used for risk analysis of metabolic syndrome and FBDI. The FBDI model included that 7 were composed of anti-inflammatory food groups and 3 of inflammatory food groups. The FBDI was calculated by multiplying the intake of food group by β coefficients. KNHAES were included in the validation of FBDI. The risk of metabolic syndrome was found to be 2.152 times higher in the group with the highest FBDI than in the group with the lowest one (95% Cl:1.458–3.178, p for trend = 0.000). This study developed FBDI reflecting food intake for Koreans, which showed a significant relationship with the risk of metabolic syndrome.

Graphene-based nanoparticles possess remarkable physiochemical properties, making them promising for diverse applications in biomedicine, agriculture, food, and industrial applications. These nanoparticles have also been used in the fight against COVID-19. Human and environmental exposure to graphene-based nanomaterials is increasing at an unprecedented rate. However, there is still a huge knowledge gap regarding its safety in clinical applications. The topic remains controversial; although several routes of degradation exist, the cytotoxicity of graphene-based nanoparticles has been demonstrated. Various factors that can influence the cytotoxicity of graphene-based materials are discussed. This review summarizes the physiochemical properties of graphene-based materials and critically examines the possible effects of graphene-based nanoparticles on the molecular level and adverse health outcomes. While oxidative stress-mediated cell damage has been proposed as a primary cytotoxicity mechanism for graphene-based materials, various in vivo biodistribution and cytotoxicity mechanisms are also highlighted. Therefore, this review of the literature provides an overview of the cytotoxicity of GBMs and raises concerns about their widespread application with potential hazardous consequences on the environment and human health.

(1) Background: The CEO message of hospital homepage contain various contents such as the hospital's future vision, promises with customers, upgraded services and public activities. The CEO’s message of the homepage includes non-financial information as well as financial information of corporates. Also, it provides useful information for not only company's goals and vision but also firm performance and strategies for the future. This study aims to investigate associations between CEO’s message of hospitals homepages and financial status. We used the balanced scorecard frame to analyze what content on the hospital's homepage is related to the hospital's various financial ratios. (2) Methods: We adopt a text mining method to extract significantly repeated keywords from the CEO’s message of hospital website. And we classify these keywords by a balanced scorecard frame. To examine the relationship between keywords of CEO’s message of the hospital homepage and hospital’s financial ratio, T-test is conducted for the difference in the TF-IDF (Term Frequency is Divided by Inverse Document Frequency) mean of the home page contents and its relationship with the views of the balanced scorecard framework. (3) Results: According to empirical results on 65 samples collected from local hospitals, there are some significant relationship between the qualitative content of the hospital's homepage and the quantitative financial ratio that indicates profitability, activity, leverage, liquidity, and transfer to essential business fund (EBF) income. (4) Conclusions: The introduction section of a homepage is most accessible to customers, containing the aims and ideals of hospitals and reflecting their values and visions [1]. In addition, in view of financial status, they can either emphasize financial strength or focus on other areas to mask weakness of financial information. This study reminds us of the importance of hospital website’s disclosure, and it can be inferred from the financial status of the hospital. It also highlights the need for harmonization between quantitative data, financial statements, and qualitative data, CEO’s messages. (5) Implications: To our best knowledge, this paper is the first research attempting to investigate the relation between text of hospital homepage and financial ratio of hospital through text mining technique and balanced scorecard frame. Hospitals take a crucial part in a country’s welfare and healthcare backbone industry. Nevertheless, in many countries, hospital organization sectors tend to remain a source of critical fiscal deficits due to its ineffective and sloppy management. We expect that the result of this paper can provide hospital managers to useful information.

The endometrium is an important part of the uterus. The human endometrium is a complex and dynamic tissue that goes through phases of growth and regression during any menstrual cycle. A thin endometrium might be relevant to a lower rate of implantation as well as a higher rate of miscarriage. Several treatments have been developed for thin endometrium, such as granulocyte colony-stimulating factor, stem cell therapy, acupuncture and physical therapy, among others. These approaches have been shown to have effects on the endometrium related to reducing the area of fibrosis, increasing the number of glands, promoting angiogenesis, increasing endometrial thickness, improving tissue structure, and increasing pregnancy rates. This review summarizes the key role of these treatments in repairing thin endometrium and improving clinical pregnancy rates

Liver cirrhosis is one of the most prevalent chronic liver diseases worldwide. In addition to viral hepatitis, genetic conditions such as steatohepatitis, autoimmune hepatitis, sclerosing cholangitis, and Wilson’s disease can also lead to cirrhosis. Moreover, alcohol can cause cirrhosis on its own and exacerbate chronic liver disease from other causes. The treatment of cirrhosis can be divided into addressing the cause of cirrhosis and reversing liver fibrosis. To this date, there is still no clear consensus on the treatment of cirrhosis. Recently, there has been a lot of interest in potential treatments that modulate the gut microbiota and gut-liver axis for the treatment of cirrhosis. According to recent studies, modulation of the gut microbiome by probiotics ameliorates the progression of liver disease. The precise mechanism for relieving cirrhosis via gut microbial modulation has not been identified. This paper summarizes the role and effects of the gut microbiome in cirrhosis based on experimental and clinical studies on absorbable antibiotics, probiotics, prebiotics, and synbiotics. Moreover, it provides evidence of a relationship between the gut microbiome and liver cirrhosis.

We employ another approach to quantize electromagnetic fields in the coordinate space, instead of the mode (or Fourier) space, such that local features of photons can be efficiently, physically, and more intuitively described. To do this, coordinate-ladder operators are defined from mode-ladder operators via the unitary transformation of systems involved in arbitrary inhomogeneous dielectric media. Then, one can expand electromagnetic field operators through the coordinate-ladder operators weighted by non-orthogonal and spatially-localized bases, which are propagators of initial quantum electromagnetic (complex-valued) field operators. Here, we call them QEM-CV-propagators. However, there are no general closed form solutions available for them. This inspires us to develop a quantum finite-difference time-domain (Q-FDTD) scheme to numerically time evolve QEM-CV-propagators. In order to check the validity of the proposed Q-FDTD scheme, we perform computer simulations to observe the Hong-Ou-Mandel effect resulting from the destructive interference of two photons in a 50/50 quantum beam splitter.

In this study, we resequenced the mitogenomes of P. megacephalus from different regions using a “primer bridging” approach with Sanger sequencing technologies. The mitogenome of this species was found to contain two copies of the ND5 genes and three copies of the control regions. Furthermore, multiple tandem repeats were identified in the control regions. Notably, we observed that there was no correlation between the distribution of species and their genetic distance. However, our research revealed the discovery of the “missing” ATP8 gene in P. megacephalus as well as three other previously published Polypedates, as a result of manual data curation. Using the mitogenome, gene expression analysis was performed via RT-qPCR of liver samples and determined that COIII, ND2, ND4, and ND6 were reduced to 0.64±0.24, 0.55±0.34, 0.44±0.21 and 0.65±0.17 under the low-temperature stress (8℃), respectively, as compared with controls (P<0.05). Remarkably, the transcript of long non-coding RNA (LncRNA) between positions 8029 and 8612 decreased significantly with exposure to low-temperature stress (8℃). Antisense ND6 gene expression showed a downward trend but this was not significant. These results reveal that modulations of protein-coding mitogenomes genes and lncRNAs of P. megacephalus play a crucial part in the molecular response to cold stress.

In response to the growing need for efficient energy conversion technologies, this pa-per introduces an innovative Tubular Thermoelectric Generator (TTEG), specifically de-signed for high-efficiency conversion of waste heat into electrical energy. Unlike conven-tional flat plate thermoelectric generators (FTEGs), the TTEG incorporates full-ring ther-moelectric elements within a tubular layout, offering a novel approach to thermal energy recovery from fluid-based systems. This design significantly enhances the heat transfer capabilities, thereby improving the efficiency of energy conversion. Comprehensive simulations and analyses form the core of this study, where the per-formance of the TTEG is rigorously compared with traditional FTEGs. These comparisons highlight the advantages of the tubular design in terms of energy conversion efficiency and practical applicability in various scenarios. The findings reveal that the TTEG not only outperforms its flat plate counterparts but also presents a scalable and adaptable so-lution for waste heat recovery in a wide range of industrial and automotive applications. This research contributes to the field of energy science and technology by presenting a detailed experimental setup, complete with reproducible procedures and results. It opens new pathways for the development of more sustainable and efficient energy conversion systems, aligning with the goal of harnessing renewable and sustainable energy sources. The potential applications of this technology in enhancing energy efficiency and reducing environmental impact are vast, making it a significant step forward in the quest for clean and sustainable energy solutions.

Salinity acts as a critical environmental filter on microbial communities in natural systems, negatively affecting microbial diversity. However, how salinity affects the community assembly remains unclear. This study used Wendeng multi-pond saltern as a model to evaluate the prokaryotic community composition and diversity and quantify the relative importance of ecological processes across salinity gradients. Results showed that low saline salterns (45-80 g/L) exhibited higher bacterial diversity than those in high saline salterns (175-265 g/L). The relative abundance of taxa assigned to Halanaerobiaceae, Haloferacaceae, Desulfohalobiaceae, Phormidiaceae, Rohodobacteraceae, and Nitrococcaceae was higher with increasing salinity. Salinity and pH were the primary environmental factors that directly or indirectly determined the composition and diversity of prokaryotic communities. Microbial co-occurrence network dynamics were more complex in the sediment than in water of salterns. An infer Community Assembly Mechanisms by Phylogenetic-bin-based null model analysis (iCAMP) showed that microbial community assembly in sediment and water differed. Our findings provide more information about microbial community structure and the importance of various ecological processes in controlling microbial community diversity and succession along salinity gradients in water and sediment environments.

Surface initiated atom transfer radical polymerization (SI-ATRP) is one of the most versatile technique to modify the surface properties of material. Recent developed metal free SI-ATRP makes such technique more widely applicable. Herein photo-induced metal-free SI-ATRP of methacrylates, such as methyl methacrylate, N-isopropanyl acrylamide, and N,N- dimethylaminoethyl methacrylate, on the surface of SBA-15 was reported to fabricate organic-inorganic hybrid materials. SBA-15 based polymeric composite with adjustable graft ratio was obtained. The structure evolution during the SI-ATRP modification of SBA-15 was monitored and verified by FT-IR, XPS, TGA, BET, and TEM. The obtained polymeric composite showed enhanced adsorption ability for the model compound toluene in aqueous. This procedure provides a low cost, ready availability, and facile modification way to synthesize the polymeric composites without the contamination of metal.

The KcsA is a prokaryotic potassium-oriented channel, which is sourced from the Streptomyces lividans soil bacteria. From extensive studies that have been carried over the KcsA potassium channel, it has been proved that various factors enable the gating and shuttling of the potassium ions into and out of the cells. Some of the factors include the different concentration of protons in the inside and outside membrane. The other factor is the existence of the selectivity filter equipped in the exit of channel pore, which enables the movement of the K⁺ ions. Not only are potassium ions present in the channel but also sodium ions. Potassium and sodium ions are the ions that are essential in the conductivity of a cell because of their charge. An intuitive idea about why K⁺ ions are at least 10,000 times more permeant than Na⁺ ions is presented in various entities. The hypothesis is that the selectivity ratio is probably related to the successive entry of Na⁺ ions, based on the premise that the ratio seems to be relevant to unpredictable quantities caused by Brownian corrosion of ions.

The EULAR Sjögren's Syndrome Disease Activity Index (ESSDAI), EULAR Sjogren’s Syndrome Patient Reported Index (ESSPRI), and other patient-reported outcomes (PROs), such as the visual analog scale (VAS) for symptoms and EULAR sicca score (ESS), are used to assess the disease activity of primary Sjögren’s syndrome (pSS). Recently, Clinical ESSDAI (ClinESSDAI) and Clinical Trials ESSDAI (ClinTrialsESSDAI) were developed for objective clinical disease activity indexes. However, the relationship of ClinESSDAI and ClinTrialsESSDAI with PROs as well as that between ESSPRI and other PROs and the objective parameters of glandular function in pSS have not been established. Herein, we investigated the correlation of ESSPRI and other PROs with the objective parameters of glandular function and the relationship of PROs with ClinESSDAI and ClinTrialsESSDAI in 66 patients with pSS. Correlations were calculated with Spearman’s correlation coefficient. ClinTrialsESSDAI was correlated with ESSPRI, dryness (ESSPRI-Dryness), fatigue, and pain domains of ESSPRI, VAS for oral dryness (oral-VAS), and patient’s global assessment. Although ESSPRI did not correlate with the objective parameters of glandular function, ESSPRI-Dryness, ESS, and oral- and ocular-VAS did. These results suggest that ESSPRI-Dryness, ESS, and VAS for symptoms, but not ESSPRI, reflect the glandular dysfunction and that ClinTrialsESSDAI correlates with PROs for dryness in pSS.

This paper provides a study on the development of solar energy, its prospects, and its impacts in Africa. Although the main focus is on technologies adopted for different uses (solar farms, mini-grids, off-grid, solar houses, irrigation, lighting, etc.), we also consider some aspects that increase the adoption of solar energy, such as legislation and business models. Finally, we will examine current and future solar projects managed by NGOs and international companies and how they benefit to leveraging social and economic standards, quality of life as well as capacity building in Africa. This study shows the plethoric interest of institutions outside Africa in the market of solar energy in the continent and that there is no African strategy to increase its independency toward a sustainable development particularly through energy transition.

FeZnNa@SiO2-C catalyst with graphitized carbon (GC) modified mesoporous SiO2 support metal nanoparticles was prepared by sol-gel method. The effect of adding metal Na and Zn promoters as a dispersion on the CO2 hydrogenation to low olefins was systematically studied. The results showed that Zn-Na, as a combination, promoted the absorption of CO2 and improved the conversion rate of CO2. Na as an alkaline substance can improve the absorption of more acidic CO2, improving the conversion rate of CO2 to 59.03%. Meanwhiles, addition of secondary metal Zn into Fe-based catalysts to form a surface alloy could alter the adsorption of CO2 and the activation of C-O bonds, inhibit the subsequent hydrogenation of olefins to paraffins, facilitate the reduction of Fe2O3 and the formation of active Fe5C2 species. From TEM and XRD, the formation of active Fe5C2 species was found, the selectivity of the target product was 41.07%. The deep hydrogenation of olefins is inhibited, by inhibiting their deep hydrogenations, the STY of C2=-C4= was raised again, up to 0.0436. However, the corresponding STY does not increase infinitely with the increase of Na content, and when the Na content to 6.4%, which can be shown higher CO2 hydrogenation catalytic performance. Compared with Fe@SiO2-C catalyst, Na and Zn promoted Fe-based catalysts prepared by modified sol-gel method, can be used directly for highly efficient CO2 hydrogenation to low olefins and thus will be more promising in the future.

In this paper, we present an experimental procedure to enhance the dimensional accuracy of fabrication via Stereolithography (SLA) of features at the micro-scale. Using a custom benchmark part, deviations in feature dimensions (micro-pores diameters and depths) were detected and measured by confocal microscopy. Samples characterization and experimental observations allowed the identification of inaccuracy sources, mainly due to the laser beam scanning strategy and to the incomplete removal of uncured liquid resin in post-processing (i.e., IPA washing). As a technology baseline, the measured dimensional errors on pores diameters were up to -46%. A compensation method of the nominal laser spot diameter (85m) was defined and implemented resulting in relevant improvements in dimensional accuracy of 9.8% and 11.3% on full-open pores diameter and depth, respectively. Further investigation was performed on a customized test part to adjust the calibration procedure. The measurements revealed that the estimate of the laser beam spot size is 968m. Measurements on micro-pores having different sizes revealed that a constant compensation parameter (i.e., C=85, 96, 120m) is not fully effective at the micro-scale, where average errors still remain at -24%, -18.8%, and -16% for compensations equals to 85, 96 and 120m, respectively. A further experimental campaign allowed the identification of an effective nonlinear compensation law where the compensation parameter depends on the micro-feature size C= f (D). Results show a sharp improvement in dimensional accuracy on micro-pore fabrication, with errors consistently below +8.2%. The proposed compensation method can be extended for the fabrication of any micro-features without restrictions on the specific technology implementation. Concerning the inaccuracy introduced by the laser path, experimentation with a customized part allowed the optimization of the part orientation to reduce the errors and their differences along the X and Y machine axes.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

Recent studies have proven that synthetic aperture radar (SAR) automatic target recognition (ATR) models based on deep neural networks (DNN) are vulnerable to adversarial examples. However, existing attacks are easily failed in the case where adversarial perturbations cannot be fully fed to victim models. We call this situation perturbation offset. Moreover, since background clutter takes up most of the areas in SAR images and has low relevance to recognition results, fooling models with global perturbations is quite inefficient. This paper proposes a semi-whitebox attack network, called Universal Local Adversarial Network (ULAN), to generate universal adversarial perturbations (UAP) for the target regions of SAR images. In the proposed network, we calculate the model’s attention heatmaps through layer-wise relevance propagation (LRP), which is used to locate the target regions of SAR images that have high relevance to recognition results. In particular, we utilize a generator based on the U-Net to learn the mapping from noise to UAPs and craft adversarial examples by adding the generated local perturbations to target regions. Experiments indicate that the proposed method fundamentally prevents perturbation offset and achieves comparable attack performance to conventional global UAPs by perturbing only a quarter or less of SAR image areas.

Sharding shows great potential for extending the blockchain. The current challenge facing sharded blockchain technology lies in addressing the extended transaction confirmation times caused by isolated states between shards and unbalanced transaction allocation strategies. These factors contribute to an increase in cross-shard transactions and disproportionate shard workload, ultimately resulting in indefinite confirmation delays for cross-shard transactions. A critical priority for sharded blockchain systems is to conduct a comprehensive qualitative analysis to better understand and mitigate the prolonged transaction confirmation times. We introduce a Product-Form Queue Network (PFQN) model to address the transaction confirmation time problem in sharded blockchains and incorporate a new confirmation queue to more accurately simulate the actual transaction confirmation process in the blockchain. In addition, we provide a detailed quantitative analysis of the relationship between network load, consensus efficiency, and security in sharded blockchains, laying a theoretical foundation for achieving robustness and efficiency in sharded blockchains. This research not only contributes to addressing the scalability issues in sharded blockchains but also offers a new perspective for future research directions.

Private Set Intersection Cardinality(PSI-CA) is a cryptographic method in secure multi-party computation that allows entities to identify cardinality of the intersection without revealing their private data.Traditional approaches assume similar-sized datasets and equal computational power, overlooking practical imbalances.In real-world applications, dataset sizes and computational capacities often vary, particularly in the Internet of Things and mobile scenarios where device limitations restrict computational types. Traditional PSI-CA protocols are inefficient here, as computational and communication complexities correlate with the size of larger datasets. Thus, adapting PSI-CA protocols to these imbalances is crucial.This paper explores unbalanced scenarios where one party (the receiver) has a relatively small dataset and limited computational power, while the other party (the sender) has a large amount of data and strong computational capabilities.This paper, based on the concept of commutative encryption, introduces Cuckoo filter, cloud computing technology, homomorphic encryption, among other technologies, to construct three novel solutions for unbalanced Private Set Intersection Cardinality (PSI-CA): an unbalanced PSI-CA protocol based on Cuckoo filter, an unbalanced PSI-CA protocol based on single cloud assistance, and an unbalanced PSI-CA protocol based on dual cloud assistance. Depending on performance and security requirements, different protocols can be employed for various applications.

BACKGROUND. Two sequelae of non-alcoholic steatohepatitis (NASH), ESLD and HCC, have become the leading causes for liver transplantation in the Western. The present study aims to approach the cellular metabolic disturbances involved in NASH progression that are associated with microbiota community changes. METHODS. Metabolic effects and microbiota community changes were explored in the murine with NASH progression by blocking the Na/K-ATPase/Src/reactive oxygen amplification loop using the synthetic targeting peptide pNaKtide. DNA from the terminal ileum microbiota habitat was obtained and amplified by PCR to develop DNA bacterial phylogenic sequence analysis of wild type and treated animals at 12, 24 and 48 weeks. Induced changes by pSrc normalization at 24 weeks were correlated with liver morphological changes, intestinal CD4+/CD8+ ratio, and liver macrophage CD14+ expression. Differences among groups were evaluated by ANOVA/t-test and Principal Component Analysis (PCA). RESULTS. Microbiota communities varied significantly at all time points (12, 24 and 48 weeks), with an increase of Verrucomicrobia and a decrease of Bacteroidetes and Firmicutes in the HFD group. Microbiota community changes regressed to their wild-type state at 24 weeks on treated animals, and those changes were associated with a decrease in liver inflammation and senescence, lower ileum CD4+/CD8+ T cells and higher liver CD14+ cells (p<0.05). Concomitantly, the metabolic disturbances in our diet-induced NASH model were normalized by NKA/Src signaling blockage and exercise with a paucity of apoptotic activity, mitigation of cell senescence, and regression of liver fibrosis (p<0.01). CONCLUSIONS. pSrc inhibition at caveolar α1-Na/K-ATPase rescinded NASH-related metabolic disturbances establishing resident physiological microbiota communities with concomitant paucity on apoptotic activity and regression of liver fibrosis; effects that were associated with both gut and liver T-lymphocyte responses.

The aim of the study was to test the significance of the EPT index in the water quality assessment of three types of water bodies in hilly and mountainous region of Serbia. The aquatic macroinvertebrate community was dominated by the group of insects, of which 95 taxa represent the EPT group. We compared the obtained values of biological indices used for the assessment of water quality according to the national legislation with the overall status assessment represented by the ecological quality classes (EQC). The results of the Spearman correlation test showed a negative correlation of EQC with the EPT index, BMWP score, H', total number of taxa and number of sensitive taxa, while a positive correlation was observed for the values of SI and Tubificinae %. The values of EQC and biological indices were subjected to principal component analysis (PCA). The results showed that the parameters that contributed most to the differences were the EPT index, the BMWP score and the number of sensitive taxa. The results indicate that the EPT index is an excellent indicator of changes in water quality and an important tool for the ecological categorization of water bodies in mountain regions.

The aim of this study was to investigate the physicochemical characterization and biological activities of chitosan (CH) based composite films with the incorporation of chestnut flower essential oil (CFEO). The composite films were prepared by casting method and characterized in terms of structural, morphological and mechanical properties via FT-IR, XRD, UV, SEM and TGA. The results proved the significantly increased water vapor permeability (WVP), heat resistance, antibacterial and antioxidant capabilities of CH-CFEO films. The incorporation of CH and CFEO enhanced the UV blocking, which made the film shield almost all UV light. Films with the tensile strength of 6.37 ± 0.41 MPa and elongation at break of 22.57 ± 0.35% were got with 6 mg mL-1 CFEO. Subsequently, the fruit preservation experiments also confirmed that the composite films could effectively extend the shelf life of bananas through their excellent water vapor and oxygen barrier. These desirable performances enable our newly developed composite films to be a remarkable packaging material to solve the fresh fruit preservation dilemma.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

To characterize the fecal microbiota of lactating Bactrian camels, this study employed a random selection of camels, assigning them to three groups: the first parity group, the third parity group, and the fifth parity group. The fecal microbial community of lactating camels was assessed using 16S rRNA amplicon sequencing, and the resulting library was sequenced on an Illumina NovaSeq platform. The first parity group was characterized by Verrucomicrobiaceae as a distinctive bi-omarker, whereas Clostridiaceae exhibited a similar role to the third parity group. In terms of functional analysis, the relative abundance of the Steroid biosynthesis pathway was highest in the first parity group, whereas the fifth parity group demonstrated a higher relative abundance of the Tuberculosis pathway compared to the other groups. The first parity group exhibited the greatest presence of seven types of enzymes, whereas the fifth parity group displayed the highest levels of two specific enzymes. Additionally, a positive association was observed between the relative abundance of the Steroid biosynthesis pathway and Verrucomicrobiaceae. Furthermore, the relative abundance of the Tuberculosis pathway displayed positive correlations with 14 enzymes. In conclusion, this study revealed that different parity was associated with distinct fecal microbial ecologies in lactating Bactrian camels.

Distributed/semi-distributed models are considered to be sensitive to the spatial resolution of the data input. In this paper, we take a small catchment in high urbanized Yangtze River Delta, Qinhuai catchment as study area, to analyze the impact of spatial resolution of precipitation and the potential evapotranspiration (PET) on the long-term runoff and flood runoff process. The data source includes the TRMM precipitation data, FEWS download PET data, and the interpolated metrological station data. GIS/RS technique was used to collect and pre-process the geographical, precipitation and PET series, which were then served as the input of CREST (Coupled Routing and Excess Storage) model to simulate the runoff process. The results clearly showed that, the CREST model is applicable to the Qinhuai catchment; the spatial resolution of precipitation had strong influence on the modelled runoff results and the metrological precipitation data cannot be substituted by the TRMM data in small catchment; the CREST model was not sensitive to the spatial resolution of the PET data, while the estimation fourmula of the PET data was correlated with the model quality. This paper focused on the small urbanized catchment, suggesting the influential explanatory variables for the model performance, and providing reliable reference for the study in similar area.

2.25Cr-1Mo steel with high strength at high temperatures and good hydrogen resistance is widely used for power generation boiler material in high temperature and pressure use environments. Following the test evaluation of the ASME Boiler and Pressure Vessel Code, specimens from the base metal of a boiler pipe were found to have impact toughness values of 285 and 21 ft-lb, which are drastically different values. The analysis of the fracture surface of the 21 ft-lb test specimen revealed MnS inclusions, and it was found that cracks initiated at the inclusions. Observation of the cross-section of the crack propagation front revealed that cracks propagated along the ferrite regions and precipitate voids. Inclusions were also found in the 285 ft-lb impact specimen; however, the volume fraction of the inclusions was significantly less than that of the 21 ft-lb specimen. It was also found that the ferrite and carbide content of the 285 ft-lb specimen was less than 21 ft-lb specimen. The reason that the inclusions, ferrite, and carbide content differed in the two adjacent impact test specimens was analyzed. The effects of micro-segregation, such as MnS inclusions on ferrite and carbide, were compared and analyzed.

Abstract Purpose: To analyze the correspondence between refractive astigmatism and corneal astigmatism in pseudophakic eyes with non-toric intraocular lenses. Setting: Yeouido St. Mary hospital, Seoul, South Korea Design: Evaluation of a diagnostic test instrument. Methods: This retrospective study included 95 eyes of 95 patients. Corneal astigmatism was measured with an automated keratometer (RK-5, Canon) and Scheimpflug tomography (Pentacam HR, Oculus). Refractive astigmatism was compared to keratometric astigmatism (based on anterior corneal measurements only), Equivalent K Reading and total corneal astigmatism (both based on anterior and posterior corneal measurements). Vector analysis was carried out by Næser’s polar value method. The accuracy was defined as the average magnitude of the vectorial difference in astigmatism (DA). Each corneal measurement was optimized in retrospect by a multiple linear regression equation between refractive and corneal astigmatism. Results: Keratometric astigmatism overestimated with-the-rule (WTR) refractive astigmatism and underestimated against-the-rule (ATR) refractive astigmatism. Several measurements based on both corneal surfaces values did not show any statistically significant difference with respect to refractive astigmatism. The mean corneal astigmatism by total corneal refractive power (TCRP) at 4.0 mm (zone/pupil) produced the lowest mean arithmetic DA and the highest percentage of eyes with a DA ≤0.50 diopter. After optimization, the accuracies of automated KA and TCRP 4.0 mm (zone/pupil) were similar. Conclusions: Total corneal astigmatism measured by the Scheimpflug tomography at 4.0 mm zone centered on pupil, accurately reflects the refractive astigmatism in pseudophakic eyes. However, the accuracy of total corneal astigmatism is not different from automated KA after optimization.

In this paper, bikeshare data in Chicago on weather-friendly days in 2019 and 2020 were analyzed to investigate the variation in bikeshare travel before and during the pandemic. Our results show that bikeshare trips during the pandemic were much longer than prior to the pandemic. The increased rate of bikeshare usage was unbalanced spatially and varied significantly for different user types. Specifically, bikeshare was used significantly more by casual users than by subscribers, and the increase occurred much more in the outskirts of the city. The increase in bikeshare travel was associated with a reduction in travel by ride-hailing and public transit, especially in the urban periphery. The correlation of bikeshare use with the bus system was much less significant than with the rail system. Bike lanes/facilities had a mixed effect on bikeshare travel. Weekend bike trips increased in areas where there was no bike lane. Weekday trips, on the contrary, increased in the vicinity of bike greenways.

SARS-CoV-2 (2019-nCoV), a novel coronavirus, caused the pneumonia outbreak in China and continue to expand. The host receptor for 2019-nCoV Angiotensin-converting enzyme 2 (ACE2), is the same as the host receptor for SARS-CoV. Targeting ACE2 holds the promise for preventing and inhibiting 2019-nCoV infection. Chinese Medicine herbs could be a valuable pool for identifying active compounds for treating infection of 2019-nCoV. In this study, we summarize several active compounds, including baicalin, Scutellarin, Hesperetin, Nicotianamine and glycyrrhizin that could have potential anti-2019-nCoV effects. We conduct molecular docking to predict their capacity for binding ACE2, which may prevent the 2019-nCoV infection. We propose that these selected compounds worth further investigation for preventing 2019-nCoV.

In the construction of shield crossing existing mined tunnel without load, it is imperative to develop corresponding design standards that reflect actual engineering force characteristics to ensure the successful completion of tunnel construction. This research uses The MIDAS-GTS finite element software to facilitate the creation of a numerical model of the shield structure for an air-push-over mine tunnel project in Changsha, China, investigating the stress field’s evolution during shield construction, and calculating the maximum positive and negative bending moments and maximum axial forces for different structures and other force states under various construction conditions. This study's findings informed the design and construction optimisation of the shield tunnelling empty-push method. The outcomes of this numerical simulation led to several key findings: (1) The soil density exerted a significantly greater impact on the internal forces of the initial support structure than both the tunnel depth and soil Poisson's ratio. Additionally, a sudden shift in internal forces occurred within the 300-350 mm range when the lining thickness was altered. (2) Factors such as the tunnel depth, soil density, soil Poisson's ratio μ, and lining thickness have a similarly influenced internal forces of the segment and the initial support. Notably, the backfill layer thickness significantly affected the segment’s maximum axial force causing an abrupt change of approximately 300 mm. (3) Under the shield machine equipment’s weight constraint, it is essential to control the guide rail’s thickness, to prevent it from becoming overly large.

During early embryonic development, fertilized one-cell embryos develop into preimplantation blastocysts and subsequently establish three germ layers through gastrulation during post-implantation development. In recent years, stem cells have emerged as a powerful tool to study embryogenesis and gastrulation without the need for eggs, allowing the generation of embryo-like structures known as synthetic embryos or embryoids. These in vitro models closely resemble early embryos in terms of morphology and gene expression and provide a faithful recapitulation of early pre- and post-implantation embryonic development. Synthetic embryos can be generated through a combinatorial culture of three blastocyst-derived stem cell types, such as embryonic stem cells, trophoblast stem cells, and extraembryonic endoderm cells, or totipotent-like stem cells alone. This review provides an overview of the progress and various approaches in studying in vitro embryogenesis and gastrulation using stem cells. Furthermore, recent findings and breakthroughs in synthetic embryos and gastruloids are outlined. Despite ethical considerations, synthetic embryo models hold promise for understanding mammalian (including human) embryonic development and have potential implications for regenerative medicine and developmental research.

A study was carried out in a Waste Sorting Plant (WSP) located in France and treating dry recyclable household waste (DRHW) as well as dry recyclable commercial and industrial waste (DRCIW). The aim was to investigate the exposure to bioaerosol and dust. The aim of the study was to assess the extent to which the measurement of concentration, species composition and particle size distribution can contribute to a better assessment of the biological risks associated with exposure. Both stationary and personal bioaerosol and dust samples were collect in the (WSP). The results confirm that waste and waste sorting activities are sources of airborne fungi. Indeed, ambient concentrations ranged from 7.3×103 to 8.5×105 CFU/m3 for culturable moulds and up to up to 4 mg/m3 for dust. Personal exposure to inhalable dust was found up to 3 mg/m3 for dust and ranged from 8.6×103 to 1.5×106 CFU/m3 for fungi. Airborne fungal communities were found to be dominated by the Penicillium genera in both bioaerosols and settled dust samples, followed by the Aspergillus, Cladosporium, Wallemia, Mucor, and Rhizopus genera. Fungi were carried by particles of aerodynamic diameters mainly between around 2.0 and 10.0 µm. The findings dealing with size distribution and biodiversity of bioaerosols suggest that employees are exposed to complex bioaerosols during their work and helps to make a finer diagnosis of the risks involved, which is often difficult in the absence of any OEL for bioaerosols in general.

The robust fusion estimation problem of a multi-sensor system with communication constraints, random packet drops, d-step state delays, and deterministic control inputs is investigated. The state augmentation method is used to transform the time delay system into a non-time delay system, and then a robust fusion estimation algorithm based on sensitivity penalty is proposed and the pseudo-cross-covariance matrix is updated. An event-triggered robust fusion estimator with state delay and deterministic control inputs is considered to make the model closer to reality while effectively reducing network congestion and lowering communication costs. Conditions are given to ensure that the estimation errors of the robust fusion estimator are uniform boundedness. Two sets of numerical simulations are provided to illustrate the effectiveness of the derived fusion estimator.

Merkel cell carcinoma (MCC) is a rare, highly aggressive skin cancer characterized by two etiologies: the first one, observed in most cases, is attributed to Merkel cell polyomavirus (MCPyV), a DNA tumor virus, while the second one is due to ultraviolet (UV) radiation exposure. Currently, there are limited diagnostic, prognostic, and therapeutic biomarkers available for MCC. MicroRNAs (miRNAs) are small RNA molecules that do not code for proteins but regulate various cellular processes, including cell cycle progression, proliferation, differentiation, and apoptosis. The dysregulation of miRNAs has been associated with a wide range of cancers since they can act as either tumor suppressors or oncogenes. This paper aims to collect, summarize and re-organize the recent discoveries concerning miRNAs, whose dysregulation in the pathogenesis and progression of MCC is slowly emerging. Furthermore, the potential clinical applications of miRNAs as diagnostic biomarkers, possible differentiation between MCPyV-related and unrelated MCC, predictors of response to therapy and prognostics are also discussed. From this review, it emerges that miRNAs may have, in the near future, the potential to become clinically significant in improving the diagnostic accuracy, prognostic evaluation, and therapeutic options of MCCs. Finally, the new perspectives on the poorly explored field of artificial intelligence in MCC are provided.

Recently, attention mechanisms have developed into an important tool for performance improvement of deep neural networks. In computer vision, attention mechanisms are generally divided into two main branches: spatial and channel attention. Both attention categories have their own advantages. The fusion of both attentions achieves higher performance, on the cost of the computational load. This paper introduces an innovative and lighter n-shifted sigmoid channel and spatial attention (CSA) module to reduce the computational cost and to improve the 3D scene relevant features selection. To validate the proposed attention module, 3D scene object detection in the deep Hough voting point sets is considered as the testing application. The proposed attention module with its piecewise n-shifted sigmoid activation function improves the network’s learning and generalization capacity which effectively predict bounding box parameters directly from 3D scenes and detect objects more accurately. This advantage is achieved by selectively attending to more relevant features of the input data. When used in the deep Hough voting point sets, the proposed attention module outperforms state-of-the-art 3D detection methods on the sizable SUNRGBD dataset. Experiments conducted showed an increase of 12.02 mean accuracy precision (mAP) when compared to the celebrated VoteNet (without attention). It also got 9.92 mAP higher compared to the MLVCNet, and 10.32 mAP higher than the Point Transformer. The proposed model not only decreases the sigmoid vanishing gradient problem but also brings out valuable features by fusing channel-wise and spatial information while improving accuracy results in 3D object detection.

In this presented case, a 77 years old woman suffering from ongoing knee pain underwent a bone scan using 99mTc-hydroxydiphosphonate (HDP) in suspicious for bone infection. An incidental finding from this scan revealed diffuse cardiac uptake, necessitating further diagnostic procedures to exclude the possibility of cardiac amyloidosis. In the subsequent 99mTc-3,3-diphosphono-1,2-propanodicarboxylic acid (DPD) scan and SPECT images, no perceptible cardiac uptake was observed at all. Upon retrospective review of the patient’s medical records, she had received 1000mg of ferric carboxymaltose for iron-deficient anemia, the day before the 99mTc-HDP bone scan. Therefore, it is assumed that the diffuse and temporary cardiac activity was due to the transient iron overload. We present and share this bone scan images in order to avoid possible future misinterpretation of cardiac amyloidosis.

Due to the highly nonlinear, multi-stage, and strongly time-varying marine lysozyme fermentation process, it is difficult to assure the stability and prediction accuracy of the traditional single global soft sensor model on a global scale. This study innovatively proposed a soft sensor model based on an improved seagull optimization algorithm (ISOA) combined with Gaussian process regression (GPR) weighted ensemble learning. First, the sample data set is divided into multiple local sample subsets by the improved density peak clustering algorithm (ADPC). Second, the Gaussian process regression model is optimally altered with an improved seagull optimization algorithm for the purpose of establishing the corresponding sub-prediction model. Finally, the prediction model's fusion strategy is ultimately determined depending on the degree of connection between the test samples and a subset of local pieces. Simulation results show that the proposed soft sensor model, which searches GPR based on ISOA and combines various sub-models, can predict the key biochemical parameters of the marine lysozyme fermentation process better with less prediction error under the condition of fewer training data, and it can be expanded to the soft sensor models of general nonlinear systems, according to simulation results.

Polymethyl methacrylate (PMMA) polymer is widely used in various fields today. In order to thoroughly reveal the structural impact performance of PMMA materials, this paper is based on the comprehensive Johnson-Cook constitutive model and damage failure model, and accurately confirm the J-C constitutive and damage failure model parameters of PMMA through material test data, The dynamic process of steel bullet impacting PMMA plate structure is analyzed by finite element software ABAQUS. The calculation results show that the numerical simulation results in this paper are in good agreement with the experimental test data. Therefore, the feasibility and accuracy of the impact analysis of PMMA structures based on J-C constitutive and damage failure models in this paper are studied. Finally, based on the J-C constitutive model and damage failure model, the variation of the residual velocity of the bullet with the PMMA plate thickness is analyzed in depth, that is, the results show that the residual velocity of the bullet has a certain linear relationship with the plate thickness.

In order to improve the performance of soft plantation wood, an environmentally friendly inorganic-organic hybrid wood modifier was developed. First, using urea and melamine as crosslinking agents, the waterborne glucose silicone resin (MUG) was prepared with glucose under the catalysis of inorganic acid and metal ions. Then MUG resin was diluted to 10% and 20% mass fraction, and compounded with sodium silicate (S) of 20% and 10% mass fraction, so the inorganic-organic hybrid G10S20 and G20S10 wood modifier were obtained respectively. Then plantation poplar wood (Populus tomentosa) were impregnated and modified with them. Their physical and mechanical properties were tested and compared with those of the wood treated with S of 20% mass fraction (S20). Infrared analysis showed that amino resin characteristic structure (CO-NH-) existed in MUG resin. The resin has good permeability. Compared with S20 modified wood, the degree of shrinkage of G10S20 or G20S10 modified wood is reduced, their moisture absorption is reduced, and their dimensional stability is improved. Waterborne glucose silicone modifier can effectively improve the wood density, modulus of elasticity, modulus of rapture and compression strength. SEM analysis showed that the cell wall of G20S10 modified wood was significantly thicker than the untreated wood, and there were columnar and granular solid substances attached in some cell cavities, ducts and corners, etc. EDX showed that the number of Si elements on the cell wall was significantly increased compared with the control, indicating that the modifier effectively entered the wood cell wall. The waterborne glucose silicone resin can greatly improve the physical and mechanical properties of wood through organic-inorganic hybridization. It is a green, non-formaldehyde, eco-friendly, low cost, compound wood modifier with broad application prospects.

The advancement in science and technology has led to luffa sponge (LS) being widely used as a natural material in industrial application as its polyporous structure and light texture. In order to enhance the utility of LS fibers as the reinforcement of lightweight composite materials, this study investigate its water absorption, mechanical properties, anatomical characteristic and thermal performance. Hence, moisture regain, tensile properties of LS fiber bundles were measured in accordance with standards and the structural characteristics were investigated via microscopic observation. Scanning electron microscopy (SEM) was used to observe the surface morphology and fracture surface of fiber bundles. Test results shows that the special structure where the phloem tissues degenerate to cavities had a significant influence on the mechanical properties of LS fiber bundles. Additionally, the transverse sectional area occupied by fibers in a fiber bundle (SF), wall thickness and ratio of wall to lumen of fiber cell, and crystallinity of cellulose had an impact on the mechanical properties of LS fiber bundles. Furthermore, the fiber bundles density of LS varies range of 385.46-468.70 kg/m³, much less than that of jute (1360.40 kg/m³) and Arenga engleri (950.20 kg/m³) while LS fiber bundles has superior specific modulus.

Considering characteristics of high river density, special underlying surface in plain river network region, and municipal drainage system function, river network drainage unit model is proposed, which is defined as a region surrounded by main river or embankment. Flood storage variety and control projects regulation of small rivers in each unit is simulated. With drainage catchment as an object, according to its drainage capacity, simplified municipal drainage model was developed. Coupling river network drainage unit model, simplified municipal drainage model and 2D flood routing model, urban flood analysis model for plain tidal river network region was developed, which could be applied to analyzing flood from upstream river, storm surge and local rainfall. Demonstration research was carried out in Puxi flood protected area in Shanghai.

Artistic image completion is fundamental for the preservation and restoration of invaluable art paintings and it has experienced significant progress through the implementation of deep learning methodologies. Despite these advancements, challenges persist, even with sophisticated approaches like Generative Adversarial Networks (GANs), particularly in achieving optimal results for high-resolution paintings. Small-scale texture synthesis and the inference of missing information from distant contexts present persistent issues, leading to distortions in lines and unnatural colors, especially in art paintings with complicated structures and textures. Concurrently, patch-based image synthesis has evolved by incorporating global optimization on the image pyramid to enhance structural coherence and details. However, methods relying on gradient-based synthesis encounter obstacles related to directionality, inconsistency, and the heavy computational burdens associated with solving the Poisson equation in non-integrable gradient fields. This paper introduces a groundbreaking approach, integrating Weighted Similarity-Confidence Laplacian Synthesis, to comprehensively address these challenges and advance the field of artistic image completion. This proposal addresses challenges not only in high-resolution artistic image completion but also makes a significant contribution to the broader field of patch-based synthesis by utilizing the Laplacian pyramid for enhanced edge-aware correspondence search. Experimental result confirms the effectiveness of our approach, offering promising outcomes for the preservation and restoration of art paintings with complicated details and irregular missing regions.

Currently, major e-commerce platforms are competing to improve their return services, while merchants are experiencing abuse of return policies by consumers. The effectiveness of lenient return policies is examined in helping e-commerce platforms gain a competitive advantage in this paper. A dual oligopoly model is established consisting of one platform that offers a lenient return policy with services like Instant Refunds and the other does not provide similar ones. The scenario where consumers are single-homing, while merchants are partial multi-homing is analyzed. In the scenario, many factors are examined to assess their impact on the scale of the bilateral user base and the profits for both platforms, including the proportion of consumer abusing return policies, the benefits derived from abusive returns, penalties. and costs. The findings indicate that: (1) With an increasing proportion of consumer abusing return policies, the multi-homing merchants on platform that offer lenient return service will choose to be exclusively affiliated with rival platform, accounting for a decrease in consumer base and lower platform profits compared to competitors. (2) Platform that provides lenient return policies should restrict the amount of returns to mitigate the impact of consumer abusing return policies on its profits. (3) When the proportion of consumers abusing return policies is relatively low, platform should choose moderate levels of penalty to increase the scale of both sides of users without excessively increasing costs. However. when this proportion is high, platforms should cease to offer lenient return and refund services.

Beyond semantic segmentation,3D instance segmentation(a process to delineate objects of interest and also classifying the objects into a set of categories) is gaining more and more interest among researchers since numerous computer vision applications need accurate segmentation processes(autonomous driving, indoor navigation, and even virtual or augmented reality systems…) This paper gives an overview and a technical comparison of the existing deep learning architectures in handling unstructured Euclidean data for the rapidly developing 3D instance segmentation. First, the authors divide the 3D point clouds based instance segmentation techniques into two major categories which are proposal based methods and proposal free methods. Then, they also introduce and compare the most used datasets with regard to 3D instance segmentation. Furthermore, they compare and analyze these techniques performance (speed, accuracy, response to noise…). Finally, this paper provides a review of the possible future directions of deep learning for 3D sensor-based information and provides insight into the most promising areas for prospective research.

Biomimicry in additive manufacturing often refers to topology optimization and the use of lattice structures, due to the organic shape of the topology-optimized designs, and the lattices often looking similar to many light-weight structures found in nature such as trabecular bone, wood, sponges, coral, to name a few. Real biomimetic design however involves the use of design principles taken in some way from natural systems. In this work we use a methodology whereby high resolution 3D analysis of a natural material with desirable properties is “reverse-engineered” and the design tested for the purpose. This allows more accurate replication of the desired properties, and adaption of the design parameters to the material used for production (which usually differs from the biological material). One such example is the impact-protective natural design of the glyptodont body armour. In this paper we report on the production of body armour models in metal (Ti4Al4V) and analyze the resulting mechanical properties, assessing their potential for impact protective applications. This is the first biomimetic study using metal additive manufacturing to date.

Precipitates are the primary source of strength for the Al-Mg-Si alloy. Aluminum alloy in the peak-aged state mainly contain β'' and β' precipitates. In the past, most of the literature only considered the strengthening effect of β''. Here we develop a single crystal intensity model including both precipitate enhancement effects for the first time. This model was subsequently implemented into a crystal plastic finite element method to model the uniaxial tensile process of a polycrystalline aggregate model of Al-Mg-Si alloy. The simulation results for uniaxial stretching are in good agreement with the experimental results, confirming that the constitutive parameters used for the single crystal strength model with two precipitates are based on realistic physical implications. Furthermore, by comparing the uniaxial tensile simulation results of a peak-aged alloy considering the actual precipitated phase composition of the alloy with those assuming that the precipitated phase is only the β'' phase, the predicted tensile strength of the former is around 5.65% lower than that of the latter, suggesting that the two kinds of precipitation should be considered separately when simulating the mechanical response of Al-Mg-Si alloy. It is highly expected that the present simulation strategy is not limited to the Al-Mg-Si alloys, and it can be equally applied to the other age-enhanced alloys.

In the context of inclusive education, digitalization in higher education is designed to promote the ideals of cultural diversity, social inclusivity, and sustainable development through technological means. This study explores the strategies and practices of digitalization in achieving inclusive education goals in higher education, aiming to provide theoretical and empirical foundations for education policymakers, teachers, and technology developers. This study adopts a mixed-methods research design, combining quantitative and qualitative data analysis to assess the current state of digitalization in higher education from various perspectives, particularly its effectiveness in advancing educational inclusivity. Through surveys, in-depth interviews, and case studies, data were collected from teachers, students, and administrative personnel to reveal opportunities and challenges in digital education resources and practices. The results show that while digitalization has improved the accessibility of educational resources, facilitated information sharing and cultural exchange, there are still numerous challenges, such as unequal technology access, insufficient cultural sensitivity in content, and issues related to the depth and quality of online interactions. Furthermore, the study identifies key factors supporting inclusive education, including cross-cultural curriculum design, teacher professional development, and students' critical use of digital tools. Finally, the paper presents a series of strategic recommendations, including the development of multicultural education platforms, strengthening teacher training, and building an inclusive digital environment. These recommendations aim to promote a more coordinated and inclusive higher education digital ecosystem that emphasizes not only technological innovation but also humanistic care and social responsibility. Through these measures, digitalization in higher education can better serve individual growth and comprehensive societal development.

Water resource is considered as a significant factor in development of regional environment and society. Water consumption prediction can provide important decision basis for the regional water supply scheduling optimisations. According to the periodicity and randomness nature of the daily water consumption data, a Markov modified autoregressive moving average (ARIMA) model is proposed in this study. The proposed model, combined with the Markov chain, can correct the prediction error, reduce the continuous superposition of prediction error, and improve the prediction accuracy of future daily water consumption data. The daily water consumption data of different monitoring points are used to verify the effectiveness of the model, and the future water consumption is predicted, in the study area. The results show that the proposed algorithm can effectively reduce the prediction error compared to the ARIMA.

Fundus image registration plays a crucial role in the clinical evaluation of ocular diseases, such as diabetic retinopathy and macular degeneration, necessitating meticulous monitoring. The alignment of multiple fundus images enables the longitudinal analysis of patient progression, widening the visual scope, or augmenting resolution for detailed examinations. Currently, prevalent methodologies rely on feature-based approaches for fundus registration. However, certain methods exhibit high feature point density, posing challenges in matching due to point similarity. This study introduces a novel fundus image registration technique integrating U-Net for the extraction of feature points employing FIVES for its training and evaluation, a novel and large dataset for blood vessels segmentation, prioritizing point distribution over abundance. Subsequently, the method employs medial axis transform and pattern detection to obtain feature points characterized by the Fast Retina Keypoint (FREAK) descriptor, facilitating matching for transformation matrix computation. Assessment of the vessel segmentation achieves 0.7559 for Intersection Over Union (IoU), while evaluation on the Fundus Image Registration Dataset (FIRE) demonstrates the method’s comparative performance against existing methods, yielding a registration error of 0.596 for area under the curve, refining similar earlier methods and suggesting promising performance comparable to prior methodologies.

The cancelation factor (CF) is a model for the ratio between gravity wave perturbations in the airglow intensity to that in the ambient temperature. The CF model allows to estimate the momentum and energy flux of gravity waves seen in nightglow images as well as the divergence of these fluxes due to waves propagating through the mesosphere and lower thermosphere region, where the nightglow and the Na layers are located. This study uses a set of T/W Na Lidar data and zenith nightglow image observations of the OH and O(1S) emissions to test and validate the CF model from the experimental perspective. The dataset analyzed was obtained during campaigns carried out at the Andes Lidar Observatory (ALO), Chile in 2015, 2016, and 2017. The CF modeled function was compared with observed points from an empirical method for vertically propagating waves that calculates directly the ratio of the gravity wave amplitude seen in nightglow images to the wave amplitude seen in lidar temperatures. We show that the CF analytical relationship underestimates the observed results generally. However, the O(1S) emission line has better agreement respect to the theoretical value due to simpler nightglow photochemistry. In contrast, the observed CF ratio from the OH emission deviates by a factor of two from the modeled asymptotic value.

Compared to their men counterparts, women do not rapidly climb up the leadership ladder due to a glass ceiling obstacle. This study aims to explore the inhibiting factors demotivating Africa women's leadership pursuit in Science, Technology, Engineering, and Mathematics (STEM). A qualitative approach was adopted using online open-ended questions to seek narratives from African women leaders on their roles and experiences of a STEM career. Data were collected using a non-probability, purposive sample of African women leaders in STEM in African research institutes and universities. Forty-two women in leadership positions in 12 African countries participated in the study, which was content analyzed, seeking patterns and themes to explore the narratives. A common thread exists in the tone and life experiences of the African women leaders in STEM. Scholarship, supportive organizational structure, commitment, hard work, and tenacity were all experienced as enablers of the career path process and their attained positions. The education level contributed to a strong leadership position. Women experience less acceptance than males in STEM leadership as the organizational culture still devalues women in leadership positions in several African countries. The study's contribution, the limitations, recommendations, and managerial implications are discussed, with suggestions for further research are made.

Tactics, Techniques, and Procedures (TTPs) constitute the most valuable aspect of Cyber Threat Intelligence (CTI). However, TTPs are often implicit in unstructured text, necessitating manual analysis by field experts. Automating the classification of TTPs from unstructured text is a crucial task in contemporary research. MITRE ATT&CK serves as the de facto standard for studying TTPs. Existing research constructs classification datasets based on its procedural examples for tactics and techniques. However, due to a significant proportion of small sample categories, a long-tail phenomenon exists, leading to a highly imbalanced sample distribution. Consequently, more research concentrates on categories with relatively abundant samples. This paper proposes a method that combines ChatGPT data augmentation with Instruction Supervised Fine-Tuning of open large language models. This approach offers a solution for TTPs classification in few-shot learning scenarios, achieving coverage of 625 technical categories. The Precision, Recall, and F1 scores reach 86.2%, 89.9%, and 87.3%, respectively.

This paper presents the latest developments in microCT, both globally and locally, for supporting the additive manufacturing industry. There are a number of recently developed capabilities which are especially relevant to the non-destructive quality inspection of additive manufactured parts; and also for advanced process optimization. These new capabilities are all locally available but not yet utilized to their full potential, most likely due to a lack of knowledge of these capabilities. The aim of this paper is therefore to fill this gap and provide an overview of these latest capabilities, showcasing numerous local examples.

Background/ObjectivesMental health and substance use disorders (MHD, SUD) affect cardiac allograft and VAD recipients and impact their quality of life and compliance. Limited research on MHDs and SUDs in transplant and MCS candidates and recipients. This study compares the incidence of MHDs and SUDs in transplant list, VAD, and post-transplant patients with that in heart failure patients. MethodsStudy cohorts were derived from the TriNetX using ICD-10 codes. Differences in incidence were examined using the log-rank test. Adults with mental health disorders before the window of time were excluded. Propensity score matching was performed using TriNetX to balance demographic and medical comorbidities. Statistical significance was set at p<0.05. All comparisons were made between propensity-matched cohorts. ResultsTransplant waitlist patients showed a statistically significant increase in the incidence of anxiety, panic disorder, adjustment disorder, depression, mood disorder, alcohol use disorder, and eating disorder. Post-transplant patients showed a statistically significant increase in the incidence of depression and opioid use compared to the heart failure population. VAD patients showed a statistically significant increase in the incidence of depression and a statistically significant decrease in panic disorder and anxiety. ConclusionsThe results pave the pathway for further investigations on prevention and coping strategies because deterioration of mental health will significantly impact compliance with medications as well as patient survival and quality of life. The use of opioids for pain management in the early postoperative period should be further investigated to assess its impact on long-term substance use and addiction. .

A number of challenging combinatorial optimization problems in logistics, transportations, aeronautics, and astronautics can be modeled as orienteering problems (OPs). To address the classic OP and its real-world variants, a parallel adaptive local-search algorithm based on competition and evolution (Palace) is proposed in this paper. In this algorithm, the parallelism runs proper local-search metaheuristics and operators to obtain the population per generation; then the competition grades those metaheuristics and operators to highlight the outperforming and eliminate the underperforming; also, the evolution explores large solution space and reproduces the best solutions for next generation. In this manner, the parallelism, competition, and evolution are organized in an easy-to-use algorithm and enable the expansibility, adaptivity, and exploration abilities, respectively. The Palace is examined on the classic and real-world Benchmarks about the OP, the time-dependent/independent OP with time windows, and the unmanned aerial vehicle and agile earth observation satellite planning. As a result, the Palace shows good performance in applicability and effectiveness in comparison with the state-of-the-art algorithms.

This paper presents a complete control strategy of the active return-to-center (RTC) control for electric power steering (EPS) systems. We first establish the mathematical model of the EPS system and analyze the source and influence of the self-aligning torque (SAT). Second, based on the feedback signals of steering column torque and steering wheel angle, we give the trigger conditions of a state switch between the steering assist state and the RTC state. In order to avoid the sudden change of the output torque for the driving motor when the state switches frequently between the steering assist state and the RTC state, we design an undisturbed state switching logic algorithm. This state switching logic algorithm ensures that the output value of the RTC controller is set to an initial value and increases in given steps up to a maximum value after entering the RTC state, and the output value of the RTC controller will reduce in given steps down to zero when exiting the RTC state. This therefore ensures smooth switch control between the two states and improves the driver’s steering feeling. Third, we design the RTC controller, which depends upon the feedback signals of the steering wheel angle and the angular velocity. In addition, the controller increases the auxiliary control function of the RTC torque based on vehicle speed. The experimental results show that the active RTC control method does not affect the basic assist characteristics, which effectively reduces the residual angle of the steering wheel at low vehicle speed and improves the RTC performance of the vehicle.

Reactive NO_x is one of the major air pollutants, which also plays a key role as greenhouse gas. Many research efforts have been devoted to not only detection of NO_x in air but also abatement of NO_x emission. The aim of this mini review is to provide a panoramic snapshot of the electrochemical analysis methods for the emission and detection of NO_x in atmosphere, with special emphasis on NO_x sensor. The electrochemical detecting mechanism and materials for fabricating electrochemical gas sensors are discussed and the prospects and challenges in this area are also evaluated. This work will serve as a useful source to inform the interested audience of the latest developments and applications in the field of NO_x emission and electrochemical detection.

We tested the use of mosquito traps as an alternative to insecticide spraying in Camargue (France) following the significant impacts observed on the non-target fauna through Bti persistence and trophic perturbations. In a village of 600 inhabitants, 16 Techno-Bam traps emitting CO₂ and using octenol lures were set from April to November 2016. Trap performance was estimated at 70% overall based on mosquito landing on human baits in areas with and without traps. Reduction of Ochlerotatus caspius and Oc. detritus, the two species targeted by Bti spraying, was respectively 74 and 98%. Traps were less efficient against Anopheles hyrcanus (46%), which was more attracted by lactic-acid than octenol lures based on previous tests. Nearly 300 000 mosquitoes from nine species were captured, with large variations among traps, emphasizing that trap performance is also influenced by surrounding factors. Environmental impact, based on the proportion of non-target insects captured, was mostly limited to small chironomids attracted by street lights. Breeding success of a house martin colony was not significantly affected by trap use, in contrast to Bti spraying. Our experiment confirms that deployment of mosquito traps can offer a cost-effective alternative to Bti spraying for protecting local populations from mosquito nuisance in sensitive natural areas.

The growing interest in Na-ion batteries as a “beyond lithium” technologies for energy storage drives the research for high-performance and environment-friendly materials. Na2Ti3O7 (NTO) as an eco-friendly, low-cost anode material shows a very low working potential of 0.3 V vs Na+/Na but suffers from poor cycling stability, which properties can be significantly influenced by materials synthesis and treatment. Thus, in this work, the influence of the calcination time on the electrochemical performance and the reaction mechanism during cycling were investigated. NTO heat-treated for 48 h at 800 °C (NTO-48h) demonstrated enhanced cycling performance in comparison to NTO heat-treated for only 8 h (NTO-8h). The pristine material was thoroughully characterized by X-ray diffraction, laser granulometry, X-ray photoelectron spectroscopy, and specific surface area measurements. The reaction mechanisms induced by sodiation/desodiation and cycling were investigated by opernado XRD. Electrochemical impedance spectroscopy was used to evidence the evolution of the solid electrolyte interface layer (SEI) and modification of charge transfer resistances as well as the influence of cycling on capacity decay. The evolution of the crystallographic structure of NTO-48h revealed a more ordered structure and lower surface contamination compared to NTO-8h. Moreover, the residual Na4Ti3O7 phase detected after the sodium extraction step in NTO-8h seems correlated to the lower electrochemical performance of NTO-8h compared to NTO-48h.

Invasive fungal infections by Candida albicans frequently cause mortality in immunocompromised patients. Neutrophils are particularly important for fungal clearance at the early phase of infections, yet little has been known regarding which surface receptor controls neutrophil phagocytic activities during systemic C. albicans infection. CD137, which is encoded by Tnfrsf9, belongs to the tumor necrosis receptor superfamily and has been shown to regulate neutrophils in Gram-positive bacterial infection. Here, we used genetic and immunological tools to probe the involvement of CD137 signaling in innate defense mechanisms against systemic C. albicans infection. We first found that Tnfrsf9-/- mice were susceptible to C. albicans infection, whereas injection of anti-CD137 agonistic antibody protected the host from infection, suggesting that CD137 signaling is indispensable for innate immunity against C. albicans infection. Priming of isolated neutrophils with anti-CD137 antibody promoted their phagocytic and fungicidal activities through phospholipase C. In addition, injection of anti-CD137 antibody significantly augmented restriction of fungal growth in Tnfrsf9-/- mice that received WT neutrophils. In conclusion, our results demonstrate that CD137 signaling contributes to defense mechanisms against systemic C. albicans infection by promoting rapid fungal clearance whereby harmful immunopathology-induced tissue injuries are minimalized.

Abstract: Exercise has been repeatedly shown to be safe and beneficial for cancer survivors. However, there is no normative guideline for exercise prescription, and it is under exploration. Therefore, this literature review aims to provide some advice for the formulation of exercise prescriptions for patients with breast cancer-related lymphedema (BCRL) from the perspective of reducing lymphedema severity. A review of relevant studies published before November 2023 was conducted using three scientific databases PubMed, Embase, and Scopus. A total of 2696 articles were found. Eventually, 13 studies fulfilled the inclusion criteria and were included in this literature review. We concluded daily, or nearly daily exercise at home can be recommended. Moreover, reduced lymphedema severity may not be maintained after ceasing the exercise program, so exercise should be a lifelong practice.

Cloud-induced atmospheric extinction and occlusion have a major effect on the effectiveness and quality of telescope observations. Real-time cloud cover distribution and long-term statistical data are essential for astronomical siting and telescope operations. At ground-based astronomical telescope sites, cloud cover distribution is currently analyzed using manual observation methods. However, the main disadvantages of manual observation methods are human subjective, heavy workloads and poor real-time performance. Therefore, a real-time automatic cloud images classification method is desperately needed. This paper presents a new cloud identification method, which is named PSO+XGBoost model by combining eXtreme Gradient Boosting (XGBoost) and Particle Swarm Optimization (PSO). The entire cloud image is divided into 37 sub-regions in order to more precisely identify the distribution of the clouds. 19 features are then extracted, including the sky background, star density, lighting conditions, and subregion grayscale values. The experimental results have shown that the overall classification accuracy of 96.91% and our model is able to outperform several state-of-the-art baseline methods. Our approach achieves high accuracy in comparison with the manual observation methods. Moreover, this method meets telescope real-time scheduling requirements.

In recent years, the unmanned aerial vehicle (UAV) synthetic aperture radar (SAR) has become a highly sought-after topic for its wide applications in the field of target recognition, detection, and tracking. However, SAR automatic target recognition (ATR) models based on deep neural networks (DNN) are suffering from adversarial examples. Generally, non-cooperators rarely disclose any information about SAR-ATR models, making adversarial attacks challenging. In this situation, we propose Transferable Adversarial Network (TAN) to attack these models with highly transferable adversarial examples. The proposed method improves the transferability via a two-player game, in which we simultaneously train two encoder-decoder models: a generator that crafts malicious samples through a one-step forward mapping from original data, and an attenuator that weakens the effectiveness of malicious samples by capturing the most harmful deformations. In particular, compared to traditional iterative methods, our approach is able to one-step map original samples to adversarial examples, thus enabling real-time attacks. Experimental results indicate that the proposed approach achieves state-of-the-art transferability with acceptable adversarial perturbations and minimum time costs compared to existing attack methods, i.e., it excellently realizes real-time transferable adversarial attacks.

The influence of pH, temperature, biopolymer ratio, total concentration, and ionic concentration on the interaction between egg white protein (EWP) and chitosan (CS) was investigated through turbidity, zeta potential, and state diagram in our research. In addition, phase behavior was observed under various conditions. The turbidity of EWP remained low (turbidity&lt;0.03) and basically unchanged at a wide range of pH (4.0-8.0), while the turbidity of CS was slightly higher (turbidity&lt;0.2) after pH 7.0 than before. Moreover, under the same conditions, a sharply rising peak pattern was observed for the complex between EWP and CS. The maximum turbidity value was observed at 55°C, and the temperature had a mild effect on turbidity. The optimum EWP to CS ratio was found to be 12:1 based on the experiment of the turbidity curves and state diagrams influenced by different biopolymer mixing ratios. With the enhanced concentrations of total biopolymer, the maximum turbidity rose insignificantly above 0.1%.