This study assesses the biomethane (CH4) generation and greenhouse gas (GHG) emissions resulting from municipal solid waste landfilling in Phnom Penh, Cambodia, with a focus on the impact of fugitive CH4 emissions and operation processes in four landfilling scenarios: simple dumping (S1), improved management with leachate treatment (S2), engineered landfill with flaring (S3), and engineered landfill with energy recovery (S4). The study also considered the environmental benefits of carbon sequestration and landfill gas utilization. The LandGEM and IPCC FOD models were used to calculate CH4 generation over the period of 2009-2022, and it was found that approximately 18 and 21 M kg/year of CH4 are released, respectively. The energy potential from CH4 recovery was 51–61 GWh/year. Overall GHG emissions in S2 were the highest, amounting to 409–509 M kg CO2-eq/year, while S1 had lower emissions at 397–496 M kg CO2-eq/year. Flaring captured CH4 in S3 could reduce GHG emissions by at least 55%, and using captured CH4 for electricity production in S4 could mitigate at least 83% of GHG emissions. Electricity recovery (S4) could avoid significant amounts of GHG emissions (˗104.5 kg CO2-eq/tMSW). The study suggests that landfill gas-to-energy could significantly reduce GHG emissions.

Recently, federated learning (FL) has been receiving great attention as an effective machine learning method to avoid the security issue in raw data collection as well as to distribute the computing load to edge devices. However, even though wireless communications is a essential part for implementing FL in edge networks, there have been a few works that analyze the effect of wireless networks on FL. In this paper, we investigate FL in small-cell networks where multiple base stations (BSs) and users are located according to homogeneous Poisson point process (PPP) with different densities. We comprehensively analyze the effects of geographic node deployment on the model aggregation in FL on the basis of stochastic geometry-based analysis. We derive the closed-form expressions of coverage probability with tractable approximations and discuss the minimum required BS density for achieving a target model aggregation rate in small-cell networks. Our analysis and simulation results provide insightful information for understanding the behaviors of FL in small-cell networks, and it can be exploited as a guideline for designing the network facilitating the wireless FL.

Water pollution associated with flooding is one of the major problems in cities in the global South. However, studies of water quality dynamics during flood events are not often reported in literature, probably due to difficult conditions for sampling during flood events. Water quality parameters in open water (canals, rivers, and lakes), floodwater on roads and water in sewers have been monitored during the extreme fluvial flood event on 7 October 2013 in Can Tho city, Vietnam. This is the pioneering study of urban flood water pollution in real time in Vietnam. The results showed that water quality is very dynamic during flooding, especially at the beginning of the event. In addition, it was observed that the pathogen and contaminant levels in the floodwater are almost as high as in sewers. The findings show that population exposed to flood water runs a health risk that is nearly equal to that of being in contact with sewer water. Therefore the people of Can Tho not only face physical risk due to flooding, but also exposed to health risk.

In an age of market liberalization, globalization, and expanding agribusiness, there is a danger that small-scale farmers will find difficulty in fully participating in the market economy. One of the solutions to solve the above situation is to strengthen linkages between farmers and firms through contract farming. The purpose of this study is to assess the factors affecting the level of linkages between businesses and farmers in crop development in Thai Binh province, Vietnam. The two main research methods used were exploratory factor analysis (EFA) and regression analysis with survey data which was conducted from 300 farmers, 10 firms, and 15 factors related to contract-farming. The results indicated that there are 5 factors that significantly affect the level of participation of farmers in the linking process, the order of impacts from strong to weak is as follows: (1) Commitment and sharing of benefits and risks between farmers and firms in the linking process, (2) Issues related to management skills and enterprises capacity of link firms, (3) Price issues that farmers are interested in in the process of implementing links with firms, (4) Policy environment - Institutions related to farmer contracts between firms and farmers, (5) Household awareness about the benefits brought about by farmer contracts with firms. Based on results, a number of specific solutions have been proposed to enhance the efficiency of farming contracts between firms and farmers in cultivation production.

Background: Acute hepatopancreatic necrosis disease (AHPND), is a bacterial disease of whiteleg shrimp, which has a high mortality rate (100%) and incurs economic losses. Our objective was to identify the genes which lead to cell and organ damage and investigate bioproducts to prevent and treat. Methods: Litopenaeus vannamei shrimp in Thua Thien Hue province, Vietnam were collected from an infected pond and analysed at the Institute of Biotechnology, Hue University. The PirA gene of Vibrio parahaemolyticus strain K5 was isolated and analyzed for nucleotide sequence and paired with the expression vector pQE30. The expression vector was transformed into E. coli strain M15, the PirA recombinant protein was expressed in the form of 6xHis-PirA fusion protein of about 15 kDa. PirA recombinant protein was purified and determined the PirAvp binding ratio, cloning and sequencing of PirA gene from Vibrio parahaemolyticus strain K5 causing AHPND by PCR method with specific primers and molecular weights of PirAvp and the PirAvp complex. Results: PirA gene from Vibrio parahaemolyticus strain K5 was cloned into pGEM-T easy vector (Promega, USA) and screened E. coli TOP10 colonies containing pGEM T easy/PirA recombinant plasmid on LB agar/ampicillin/IPTG/X-Gal medium. PCR showing a band of about 347 bp, matching the size of PirA gene and two nucleotide sequences (BamHI and HindIII). The results showed that PirA gene has a length of 336 bp and similar to PirA gene on GenBank (Code: KU556825.1). The results of protein extracted from E. coli M15 recombinant cells and 6xHis-PirA target protein was collected in elution fractions from EF2 to EF6, showed that the concentration of 6xHis-PirA protein and EF3 elution fraction collected a highest protein concentration (1,586.54 µg/ml). Conclusions: The purified PirA recombinant protein will provide materials for development research to create biological products to prevent and treat AHPND.

Objective: This study aimed to demonstrate the availability of portable devices for nasal FeNO measurement, which could replace exhaled NO measurement based on the continuous aspiration of multiple flow measurement systems. Methods: A descriptive cross-sectional study. The healthy subjects without rhinosinusis disorders (control group) and those with diagnosed allergic rhinitis (AR group) were enrolled in the study. They underwent nasal and bronchial FeNO measurements by both fixed flow NObreath® connected to nasal mask and multiple flows HypAir FeNO®. Results: A total of 153 people were recruited including 63 healthy subjects and 90 subjects with AR. There were no statistically significant differences in anthropometric characteristics between the two groups (P > 0.05). There were a significant increase in FeNO values in the AR group compared to the control group; concentrations of nasal and bronchial FeNO mearsured by NObreath® were 76.0 ± 50.7 ppb (vs 36.0 ± 28.1 ppb, P < 0.01) and 32.3 ± 15.4 ppb (vs 9.2 ± 5.6 ppb, P < 0.001), and those mearsured by NObreath® Hypair FeNO® were 1796.9 ± 523.3 ppb (vs 400.2 ± 123.1 ppb, P < 0.001) and 37.3 ± 23.0 ppb (vs 17.4 ± 18.3 ppb, P < 0.01). A weak correlation between the values measured by NObreath® and Hypair FeNO® devices was observed (r = 0.023 and r = 0.089, respectively; p < 0.05). Conclusions: The handheld NObreath® device is effective in measuring FeNO concentrations in both normal subjects and AR patients. The advantages in price and size, creating a compact, low-cost device that is convenient for use and research.

Antibiotic-free approaches are more important than ever to deal with the rapidly growing problem of antibiotic resistance. The blue light 460nm (BL460nm) has been shown to effectively attenuate Staphylococcus aureus to chemical and physical agents through photolysis of the bacterial virulence factor Staphyloxanthin. However, the phototherapy using BL640nm has yet to be investigated in detail for its safety in eradicating Staphylococcus aureus in vitro and in vivo. In this study, we used a LED source producing a continuous wavelength of 460 nm along with hydrogen peroxide to treat S. aureus in culturing conditions and a wound abrasion mouse model. The results proved the safety of the combined therapy when it did not modify the bacterial virulence factors or the susceptibility to the widely used antibiotics. In addition, the experimental results on the mouse skin infection model also showed that the combined therapy is safe to apply to mouse skin and that it did not cause adverse skin irritation. Furthermore, the therapy can help Staphylococcus aureus-infected wounds heal with efficacy comparable to the topical antibiotic Fucidin. The above results suggest that the combination therapy of 460nm blue light and hydrogen peroxide can be safely used as an alternative to or adjunct to antibiotics in treating S. aureus-infected wounds.

This work emphasizes to use silver decorative method to enhance the antibacterial activity of TiO₂ and ZnO nanoparticles. These silver decorated nanoparticles (hybrid nanoparticles) were synthesized by using sodium borohydride as a reducing agent, with the weight ratio of Ag precursors: oxide nanoparticles = 1: 30. The morphology and optical property of these hybrid nanoparticles were investigated using transmission electron microscopy (TEM) and UV–vis spectroscopy. The agar-well diffusion method was used to evaluate their antibacterial activity against both Staphylococcus aureus and Escherichia coli bacteria, with or without light irradiation. The TEM images indicated clearly that silver nanoparticles (AgNPs, 5-10 nm) were well deposited on the surface of nano-TiO₂ particles (30-60 nm). Besides, smaller AgNPs (< 2 nm) were dispersed on the surface of nano-ZnO particles (20-50 nm). UV-vis spectra confirmed that the hybridization of Ag and oxide nanoparticles led to shift the absorption edge of oxide nanoparticles to the lower energy region (visible region). The antibacterial tests indicated that both oxide pure nanoparticles did not exhibit inhibitory against bacteria, with or without light irradiation. However, the presence of AgNPs in their hybrids, even at low content (< 40 mg/mL) leads to a good antibacterial activity and the higher inhibition zones under light irradiation as compared to that in dark was observed.

The research is designed for developing the pilot small-scale clean development mechanism bundled project activities in Vietnam electricity/ energy sector. Its overall purpose is to assess the potential of rice husk - fuelled bio-power development projects in Mekong delta. Based on estimating the electricity potential of a bundle of rice husk-fuelled bio-power development projects in Mekong delta with the capacity of 11 MW per project, assessing their CO₂ emission reductions (CERs) and CER credits, calculating and comparing their financial indices (NPV, B/C, IRR) in two cases: W/O CDM and W/CDM, the research expects to establish a rice husk energy balance flowchart for the whole Mekong delta in the year 2021 and recommend policies to use for bio-power generation the unused rice husk that is dumped and discharged from local paddy milling centers into rivers and canals, as well as, to put forward a safe and environmentally friendly solution to minimize thoroughly the current serious pollution of rivers and canals in Mekong delta with the increasing unused rice husk quantity in the context is where the sea level rise phenomenon is the strongest in the world .

IntroductionThe aim of this study is to describe the epidemiology of all COVID-19 patients in Vietnam and to describe the measures of disease control and prevention implemented. MethodsData were recovered from Wikipedia regarding the 2020 coronavirus pandemic in Vietnam. The period covered was from 23 January to 20 April 2020. Descriptive analysis was stratified by gender, age, country of origin, travel history, clinical symptoms and outcome. A survey of disease control and prevention measures was conducted at the Centre for Disease Control in the Thai Binh province, which is responsible for screening and isolating individuals at high risk of COVID-19. ResultsAs of 20 April 2020, Vietnam had recorded 268 confirmed COVID-19 patients. 55.2% were female. 67.9% were aged 20-49 years and 82.5% were Vietnamese. 60.4% of cases were imported from outside Vietnam. Other cases were acquired in Vietnam by individuals in close contact with imported cases. Only one patient who had not travelled had had no known contact with a confirmed case. 63.1% of patients were asymptomatic. 75.7% of patients were discharged. No deaths were recorded. The Thai Binh CDC surveyed a total of 2,203 persons at risk of COVID-19. 336 persons (15.2%) were isolated at hospitals and 1,411 (64.0%) in dedicated isolation facilities. 16.4% reported at least one respiratory symptom. No positive cases confirmed by RT-PCR have been reported in the Thai Binh province to date. ConclusionThe effect of the systematic screening and isolation strategy made it possible to limit local transmission in Vietnam. Vietnam needs to reinforce diagnostic capacities, prevention measures and provide the necessary epidemiological data on which to base interventions. The wider use of rapid serological tests is also advisable in order to be able to conduct extensive screening in the community.

(1) Background: This study aimed to evaluate the role of cervical pessary for preventing preterm birth in singleton pregnant women with a cervical length (CL) ≤25 mm and a uterocervical angle (UCA) ≥95o and ≥105o. (2) Methods: A quasi-experimental study was conducted on 225 singleton pregnant women with a gestational age of 16+o-23+6 weeks and transvaginal ultrasound CL measurements ≤25 mm, whose pregnancy was man-aged at the Haiphong Hospital of Obstetrics and Gynecology, Vietnam, from September 2020 to September 2022. Participants were allocated into two groups: prophylactic treatment with progesterone (123 pregnant women) and combined with a cervical pessary (102 pregnant women). The UCAs measured via transvaginal ultrasound by a single sonographer were divided into groups with UCA measurements ≥95o and ≥105o. The gestational age at birth was classified into full-term and preterm <37 weeks and <34 weeks. A binary regression model assessed the association between CL, UCA, and pre-term birth outcomes. The difference was statistically significant, with p<0.05. (3) Results: There was no statistically significant difference in the rate of preterm birth <37 weeks and <34 weeks between the two groups (16.3% vs. 11.8% and 6.5% vs. 4.9%, p>0.05). The probability of preterm birth <37 weeks in the group of pregnant women with a UCA ≥95o treated via cervical pessary plus progesterone decreased by 60.6%, OR (95% CI) of 0.394 (0.165-0.941), p<0.05. In the group of pregnant women with a UCA ≥105o, there was a significant association in the group of progesterone treatment combined with a cervical pessary, with the lower rate of PTB <37 weeks and <34 weeks, with OR (95% CI) of 0.028 (0.005-0.146), p<0.001, and 0.141 (0.030-0.664), p<0.05, respectively. (4) Conclusion: The results of this study suggest that cervical pessary is beneficial to the prevention of preterm birth in singleton pregnant women with an obtuse uterocervical angle. Further randomized studies among pregnant women with obtuse uterocervical angles will be needed to clarify the role of a cervical pessary in preventing preterm birth.

Nonwoven fabrics have been widely used in textile manufacturing industry as a sheet or web structure because of soft, water-repellent, recycle, ecological and resilient functions. Ultrasonic welding method has been applied for bonding nonwoven fabrics due to clean, fast and reliable approach. In this work, the ultrasonic stepped horn is designed to generate uniform amplitudes on the working surface by using finite element analysis (FEA) simulation. Chromium carbon steels are utilized to produce ultrasonic horns due to high wear resistant and hardness. Isotactic polypropylene nonwoven fabrics fabricated by spunbond process were bonded by continuous ultrasonic sewing machine. Ultrasonic horn with 70 mm in diameter working at 20 kHz, polypropylene (PP) nonwoven density of 80 gsm and various design of welding joints were applied. A typical image in the case of number one was investigated by the scanning electron microscope (SEM) images of inter-facial micro-structure. However, welding joints of totally eight roller patterns was test the tensile strength of the ultrasonic welding joints on PP nonwoven fabrics. The tensile strength of the welding joints is proportional to the area ratio between the welding area and cycling area. The results showed that the melted zone without welding defects such as crack or blowhole can be seen. Furthermore, the tensile strength of welding joints in eight cases of roller patterns (No.1-No.8) was described in details. The ultrasonic welding joints with brick structures give higher tensile strength while the solid line in the pattern gave less strength.

In all forms of folk beliefs, ancestor worship is a universal traditional belief form of the Vietnamese people. As a Vietnamese people, “everyone worships their ancestors, everyone worships their parents and grandparent”. Ancestor worship is a common belief in the whole country. It is a belief that expresses the deeply humanistic spirit of the Vietnamese people and has great values in human life. So, what is the nature of ancestor worship? What is the values of ancestor worship in life? And in the context of globalization, how has this the belief changed? This study focuses on analyzing the above contents, thereby highlighting the value of this belief in the spiritual life of Vietnamese people; to point out the positive and negative changes of this belief in the current period; from that, take the right measures to bring into play the positive and limit the negative side of those changes in the spiritual life of Vietnamese people.

Curcuma longa is only a rich source of curcumin (1) and its major analogues demethoxycurcumin (2) and bisdemethoxycurcumin (3) among the Curcuma species. The content ratio of these three curcumins in turmeric is depended on the varieties and growing environment. Recently, curcumin (1) has been reported as potential inhibitor of hepatic and enzymatic protein tyrosine phosphatase 1B (PTP1B) and its related disorders such as hypertriglyceridemia, hyperlipidemia and liver steatosis. Thus, we further purified curcumins (1–3) from C. longa and investigated their inhibitory effects against PTP1B and α-glucosidase enzymes. As the result, curcumins (1–3) exhibited potential PTP1B inhibition with IC50 values of 37.8 ± 1.4, 45.3 ± 0.7, and 72.6 ± 1.1 μM, respectively, and α-glucosidase inhibition with similar manner (IC50 values of 78.2 ± 0.2, 82.4 ± 0.6, and 90.6 ± 1.0 μM, respectively). These results reveal a key role of methoxylation in the variation of PTP1B and α-glucosidase inhibitory activity for these curcumins. In addition, density functional theory (DFT) was used accompanying with molecular docking (MD) to analyze the ligand stability and the interaction of curcumins (1–3) with PTP1B and glucoside hydrolase proteins. Assay-based results and the MD data obtained are highly correlation suggesting that the deterioration of the enzyme activity caused by the distortion of structural conformation of PTP1B and glucoside hydrolase may be related to the arrangement of amino acids in protein structure. This reported for the first time that inhibitory effects of curcumins (1–3) against PTP1B and glucoside hydrolase have been examined in vitro and in silico as well.

The objectives of the research are to investigate the characteristics of the board of directors on the financial performance of the enterprise. Using a sample data from 52 construction and real estate enterprises listed on Vietnam stock exchange in the period 2006-2020. Using typical regression methods such as pooled OLS, FEM, REM and assessing the defects of the research model, the FGLS method is selected. At the same time, due to the existence of endogenous phenomena and the nature of interdependence among enterprises in Vietnam, research using the instrumental variables two-step generalized method of moments (IV-GMM) in order to correct for cross-sectional dependence, autocorrelation, endogeneity, and heteroskedasticity in the analysis. Research results suggest that board size, female board members, meeting frequency, and board members' education have a positive influence on financial performance. Moreover, the independence of the Board of Directors increases, the business efficiency decreases. The research also found a positive relationship of tangible fixed assets, and a negative relationship between capital structure choice, firm size and corporate financial performance.

Marketing is one of the important stages, the decisive factor affecting the success of production and business activities of every business. Therefore, marketing is considered to be the first and most important stage in the process of introducing, bringing products to market and branding of businesses, especially in the period when the disease situation is taking place very complicated worldwide. This study provides both qualitative and quantitative results for the following research objectives. Firstly, the study will assess the situation and analyze the appropriateness of marketing models in the current market situation trend. Secondly, the study proposes an approach in building a new type of marketing model, which is 3D web-based marketing applied in e-commerce to support the modeling of enterprise products in the form of Interactive 3D products are similar to real products. Thirdly, testing and evaluating 3D e-commerce web marketing model at Truong Hai Auto Showroom, Thai Nguyen City branch. This study also proposes a number of solutions for the research and deployment of 3D web marketing model application for businesses in the current market situation.

Stemming from the urgency of the actual situation, commercial banks need an effective credit risk management tool to limit risks. The authors went to survey, study and propose a set of factors affecting the ability of debt repayment of individual customers and conducting surveys. The topic uses data sets including 240 observation samples. Using the SPSS software to clean data and run the model based on Maddala's Binary logistics regression published in 1984 to find out the impact of each individual element of customers affecting their ability to repay such debts. Come on. The authors also specify the order of influence of each factor determining the ability to repay individual customers, thereby helping bank managers have a better visual view to make decisions for borrowing accurately, limiting risks.

The Soil and Water Assessment Tool (SWAT) is one of the most widely used hydrologic models. SWAT has been undergoing constant changes since its development. However, compartment review and testing of SWAT are comparably limited, especially the flood routing functions. In this study, the daily flood routing subroutines of different SWAT versions were reviewed and tested using a well observed segment of the Weser river located in Germany. Results show several problems with the flood routing subroutines of SWAT. The variable storage subroutine of SWAT (revision 664) does not transform the flood wave. Unphysical results could be obtained with the variable storage routing of SWAT (revision 528). The Muskingum subroutine of SWAT (revisions 664 and 528) overestimates channel evaporation (resulting in a bias of 14\% to 19% in streamflow) and underestimates transmission losses. Simulated results show that the timing and shape of the flood wave could be improved with a corrected Muskingum subroutine. Based on the results of this study, we suggest the SWAT user community to review their existing SWAT models to see how the aforementioned issues will affect their methods, findings and conclusions.

Background. There is limited evidence on the relationship between chronic kidney disease (CKD) and frailty in older people in Vietnam. This study aimed to examine the prevalence of frailty and its impact on mortality in older patients with end-stage renal disease. Method. This is a prospective, observational study at two large Dialysis Centres in Vietnam from November 2020 to June 2021. Consecutive older patients diagnosed with end-stage renal disease and on dialysis were recruited. Participants’ frailty status was defined by the Clinical Frailty Scale (CFS). The study outcome was all-cause mortality at 6th month. Results. A total of 175 participants were recruited (mean age 72.4 years, 58.9% female). Using the cut-point of CFS ≥4, 87.4% of the participants were frail. Mortality at 6th month was 14.9%, 31.9% in participants with CFS ≥7, 12.8% in participants with CFS=6, 7.5% in participants with CFS from 4 to 5, and 4.5% in participants with CFS ≤3 (p=0.001). Cox regression analysis showed that compared to the non-frail participants, the probability of death over 6 months was nearly 2-fold higher in the mildly frail, 3-fold higher in the moderately frail, and 9-fold higher in the severely frail participants. Conclusion. This study demonstrated a very high prevalence of frailty in older patients with end-stage renal disease and dialysis and the significant impact of frailty severity on mortality. Healthcare providers should consider incorporating frailty screening into routine care for older patients with end-stage renal disease and dialysis.

This article aims to identify the current development of cross-border tourism between Vietnam and China. The paper analyzes the perception and strategy of cross-border tourism development in the two countries, especially in the context of China’s implementation of the “Belt and Road Initiative” (BRI). The article emphasizes that Vietnam and China have recently made efforts to promote cross-border tourism development. At the same time, Vietnam and China see cross-border tourism development as a significant part of comprehensive border cooperation between the two countries. However, the development plans for cross-border tourism between the two countries are still mainly on the desk, not yet implemented effectively. Thus, its achievements are relatively modest. Besides, the article emphasizes that the interests of the people living in the border area, especially the Vietnam side, are almost “forgotten” in the development of cross-border travel between the two countries. Besides, the article also analyzes the challenges that the two sides are facing, especially the Vietnam side, in promoting the development of cross-border tourism between the two countries.

This study aimed to assess the prevalence and identify risk factors for schistosomiasis among school-aged children in low- and middle-income communities. A retrospective cross-sectional study was conducted, involving the examination of 24 034 children for Schistosoma haematobium ova. Data were analyzed using IBM Statistical Package for the Social Sciences (SPSS) version 27. Logistic regression was employed to determine the factors associated with schistosomiasis. The overall prevalence of schistosomiasis in the study population was 75%, with higher rates observed in rural-dominated areas, particularly Bushbuckridge (73%) and Nkomazi (51%). Age, a history of bilharzia, and the presence of blood in urine were significantly associated with schistosomiasis, while being a female child was found to be a protective factor. This study underscores the importance of implementing robust screening procedures and the necessity for health education to mitigate the high prevalence of schistosomiasis and prevent its further spread.

The material flow dynamic and velocity distribution on the melted domain surface play a crucial role on the joint quality and formation of welding defects. In this study, authors investigated the effects of the low and high currents of plasma arc welding on the material flow and thermodynamics of molten pool and its relationship to the welding defects. The high-speed video camera (HSVC) was used to observe the convection of the melted domain and welded-joint appearance. Furthermore, to consider the Marangoni force activation, the temperature on the melted domain was measured by a thermal HSVC. The results revealed that the velocity distribution on the weld surface was higher than that inside the molten weld pool due to the difference of the massive density between the air and the steel. Moreover, in the case of low welding current (80A) the convection speed of molten was faster than that of the high welding current case (160A) owing to the difference of main driving forces direction and strength, which leading to undercut and humping defects on the weld surface and excessive convex (burn-through) defect at the bottom weld side, respectively. The medium welding current (120A) had two convection patterns with the main flow in backward direction, which resulted in better welding quality without defect. The interaction between the shear force and Marangoni force played a solid state on the convection and heat transportation processes in the plasma arc welding process.

Advances in cardiovascular therapies and cancer treatments result in longer patient survival. The coexistence of cancer and cardiovascular disease has been recognized as a complex clinical scenario. Beside cardiovascular disease, older people with cancer are at greater risk of experiencing multimorbidity and the geriatric syndromes such as frailty. In older people, the concurrent presence of cancer and cardiovascular disease increased the risk of mortality, and the presence of frailty can exacerbate their conditions and hinder the treatment effectiveness. Given the significant intersection among frailty, cardiovascular disease and cancer in older people, this paper aims to provide an overview of the current research in this field and identifies gaps in research to understand the burden and impact of frailty in these populations. While many studies have examined the prevalence and impact of frailty on adverse outcomes in patients with cancer or with cardiovascular disease, evidence of frailty in individuals with both conditions is lacking. There is no universally accepted definition of frailty, which leads to inconsistencies in identifying and measuring frailty in older adults with cardiovascular disease and cancer. The frailty index seems to be a preferred frailty definition in studies in patients with cancer, while the frailty phenotype seems to be more commonly used in cardiovascular research. However, differences in how the frailty index was categorised and in how patients were classified as ‘frail’ depending on the cut points may have negative effect on understanding the impact of frailty in the studied populations. This makes it challenging to compare findings across different studies and limits our understanding of the prevalence and impact of frailty in these populations. Addressing these research gaps will contribute to our understanding of the burden of frailty in older people with cardiovascular disease and cancer, and improved clinical care protocols in this vulnerable population.

This work presented the design and fabrication of blood vessel and breast tumor detection device (BKA-06) based on optical energy spectroscopy. The BKA-06 device uses red-to-near-infrared light-emitting diodes that allow physicians or physicians to visualize blood vessels and surface structures such as breast tumors with the naked eye. The device consisted of built-in current control circuit to have the appropriate brightness (maximum illuminance of 98592 lux) for the examination of superficial tumors deep under the skin, with a scan time of 3-5 minutes. The device BKA-06 could facilely observe each layer of blood vessels at the depth of the skin. For breast tumors, the location, size and invasive areas around the tumor can also be visualized with the naked eye using the BKA-06 sensor. The results show that the BKA-06 sensor can provide clear breast tumor and vascular images with a penetration of up to 15 cm in the skin and tissue layers of the breast. The breast tumor scanning tests with the BKA-06 sensor gave patients quick results and compared them through cell biopsy and MRI respectively. The device has the advantage of being simple, easy to use, providing potential practical applications in the medical field, reducing costs for patients when taking MRI or CT scans. Therefore, the BKA-06 device is expected to help doctors and medical staff overcome difficulties in infusion as well as identify breast tumors to support early breast cancer diagnosis and treatment.

This investigation aims to discuss the formation process of eddies and the heat transportation in plasma keyhole arc welding. In order to clarify this issue, the measurement of the convection inside the weld pool, the convection on the weld pool surface, also the temperature distribution on the weld pool surface were carried out. The results showed that two eddies were found in the weld pool, which is controlled mainly through the shear force by the plasma flow acting on the weld pool surface. The magnitude, extent and direction of the shear force are thought to be determined primarily by the variation of keyhole profile. The relative shape and strength of each eddy is largely changed depending on the change of the keyhole profile when nozzle diameter changed. These relative strengths of each eddy are considered to decisively govern the heat transport in the weld pool coinciding with the direction of eddies. A larger eddy near the lower part of the keyhole inside the weld pool was found out in the case of 1.6 mm, meanwhile a upward larger eddy was found out near the upper part of the keyhole inside the weld pool in the case of 2.4 mm.

Vector geographic data play an important role in the natural resources and environment sector and other location information services. This is also one of the types of data where the cost to create it is relatively large because of the difficulty in surveying, collecting, and authorizing. The rapid development of the Internet has created many advantages in the distribution, exploitation, and use of vector geographic data, but it also gives rise to many problems such as duplication, redistribution, forgery, and illegal data use. The theft on the Internet is becoming more and more sophisticated and the number of violations is increasing, showing the urgent need to research and develop an effective solution to protect the copyright of vector geographic data and prevent them from being illegally collected and used. Among the major studies and solutions, digital watermarking emerges as an effective method and is an active research area for copyright protection. Towards a good solution for copyright protection of vector geographic data, our study proposes a new algorithm with three main contributions, including: (1) generating short, pseudo-random meaningful watermarks to increase robustness and to enable automated as well as visual manual verifying; (2) building a uniformly distributed mapping between the vertex coordinates and the watermark bit indexes to increase the robustness of the watermarks; and (3) integrate two types of watermarks, namely, spatial domain-based watermarking and zero-watermarking to be resistant to most common attacks on geographic vector data. The algorithm also allows working on all types of vector geographic data, including points, polylines, and polygons.

This study aimed to evaluate the proliferation and migration of fibroblast cells derived from chronic wounds and investigate the impact of low-level laser therapy (LLLT) on their growth and migration. A total of 60 dermal samples were obtained from three sites of chronic pressure ulcers and diabetic ulcers in 20 patients. Following collection in the operating room, the dermal samples were isolated using the procedure described by Freshney RI. Fibroblasts from the wound base (Site 1) exhibited a slow proliferation rate and a decrease in proliferative capacity. Fibroblasts from wound margins (Site 2) and adjacent healing skin (Site 3) could be successfully isolated and maintained for multiple generations without any morphological changes. Fibroblasts from chronic wounds at Sites 2 and 3 showed slower proliferation rates and reduced migration capabilities compared to normal dermal fibroblasts (control samples). The fibroblast cells were exposed to LLLT at different energy levels (2.5, 3, and 3.5 J/cm2). The laser-treated groups demonstrated a significantly higher increase in cell count compared to the control sample, with the highest increase observed at an energy level of 3 J/cm2. These findings suggest that LLLT at an energy level of 3 J/cm2 could effectively enhance fibroblast migration, indicating its potential as a therapeutic intervention for chronic wounds.

The study examines the behavior of the Mechanically Stabilized Earth (MSE) wall using available reinforcement materials in Danang, Vietnam. The MSE was reinforced by the self-fabricated galvanized steel grids using CB300V steel with 3 cm ribs. The backfill soil is a sandy clay soil from the local area with a low cohesion. A full-scale model with full instrumentation was installed to investigate the distribution of tensile forces along the reinforcement layers. The highest load that caused the wall to collapse due to internal instability (reinforcement rupture) was 302 kN/m2, which is 15 times the design load of 20 kN/m2. The failure surface within the reinforced soil had a parabolic sliding shape which is similar to the theoretical studies. At the failure load level, the maximum lateral displacement at the top of the wall facing was small (3.9 mm) which is significantly lower than the allowable displacements for the retaining wall. Furthermore, a numerical model using FLAC software was applied to simulate the performance of the MSE wall. The modeling results are in good agreement with the physical model. Thus, the self-fabricated galvanized steel grids could be confidentially used in combination with the local backfill soil for the MSE walls.

In the Vietnamese Mekong delta, soil quality and crop yield are steadily declining under rice monocultures with three crops per year. The objective of this study was to evaluate the medium-term effects of rotating rice with upland crops and adding organic amendments on rice yield and relate it to soil quality. A field trial with split-plot design including two factors and three replicates was carried out from 2017 to 2020, over the course of nine consecutive cropping seasons. Crop rotations and organic amendments were applied as main-plot and subplot factors, respectively. The rotations were: 1) rice–rice–rice (R–R–R), 2) soybean–rice–rice (So–R–R), and 3) sesame–rice–rice (Se–R–R), while organic amendment treatments included: i) no amendment (NO-AM); ii) compost of rice straw and cow manure (RS+CM), and iii) sugarcane compost (SGC); the composts were applied at a rate of 2.0 t ha-1. The rotation cycle started with the so-called spring–summer (SS), followed by summer–autumn (SA) and ended with the winter–spring (WS) season. Rice yield significantly (P &lt; 0.05) increased by organic amendments after nine growing seasons (2019–2020 WS), with an increment of 5.1% for RS+CM (7.07 ton/ha) and 6.1% for SGC (7.14 ton/ha). Contrary to our expectation, rotations with upland crops did not significantly increase rice yield. Rice yield significantly and positively correlated with an integrated soil quality index SQI (r = 0.86) for the topsoil (0–15 cm), but not for the subsoil (15–30 cm). The increased availability of soil nutrients (Si and marginally also P) and improved soil physical properties probably induced by organic amendments, along with other soil properties under study, cumulatively attributed to enhanced rice yield. Use of a SQI involving several soil quality indicators enables to overall quantify the importance of soil fertility for rice yield versus other factors and it provides an effective means of quantifying the integrated effect of improved management. Moreover, integrating a wide range of soil quality indicators in a SQI ensures its applicability across diverse settings, including different crop rotations and various soil types.

The response of a single tin oxide nanowire was collected at different temperatures to create a virtual array of sensors working as a nano-electronic nose. The single nanowire, acting as a chemiresistor, was first tested with pure ammonia and then used to determine the freshness status of trout fish (Oncorhynchus mykiss) in a rapid and non-invasive way. The gas sensor reacts to total volatile basic nitrogen, detecting the freshness status of the fish samples in less than 30 seconds. The sensor response at different temperatures correlates well with the total viable count (TVC), demonstrating that it is a good (albeit indirect) way of measuring the bacterial population in the sample. The nano-electronic nose is able to classify the samples according to their degree of freshness, but also to quantitatively estimate the concentration of microorganisms present. The system was tested with samples stored at different temperatures, managing to classify them perfectly (100%) and estimating their log(TVC) with an error lower than 5%.

In this study, effects of molecular structure transformation of canna starch (CS) in oxidation condition on physicochemical characteristics of thermoplastic starch were examined. Thermoplastic starch (TPS) samples of CS and respective oxidized starch (in 1, 3 and 5% of sodium hypochlorite, w/w) were prepared by using an internal mixer with the presence of 30 wt% of glycerol as plasticizer. The physicochemical, morphological, thermal, and mechanical properties of native starch-based TPS (NTPS) and oxidized starch-based TPS (OTPS) samples were evaluated. The content of carboxyl and carbonyl groups in oxidized canna starch (OCS) increased with the increase in the content of oxidant, leading to an improvement in the plasticization of CS. FTIR spectra of OTPS samples showed the stronger interaction between oxidized starch and plasticizer. SEM images of fracture surface indicated that the morphology of OTPS samples were smoother than that of NTPS samples. XRD patterns confirmed that the crystallite type of starches was also clearly changed after extrusion process and the decrease in crystallinity of OTPS samples is attributed to effects of both oxidation and plasticization. DSC results indicated that Tg of OTPS was greatly influenced by the carbonyl and carboxyl content and the higher content of these groups in oxidized starched could help the plasticization becomes easier. The better plasticization in OTPS samples resulted in the better mechanical properties and thermal stability of OTPS. The outcome suggested that the use of oxidized starch is an effective method to improve the plasticization in preparing thermoplastic starch.

This study compares the physico-chemical characteristics of three different types of biochar produced from biomass residues in Vietnam as a basis for optimising their application in water purification and soil fertilisation. Wood biochar (WBC), rice husk biochar (RBC), and bamboo biochar (BBC) were produced under limited oxygen conditions using equipment available locally in Vietnam, known as a Top-Lid Updraft Drum (TLUD). The resulting biochars were characterised using a suite of state-of-the-art methods to understand their morphology, surface chemistry and cation exchange capacity. Surface areas (measured by BET) for WBC and BBC were 479.34 m²/g and 434.53 m²/g, respectively, significantly higher than that of RBC which was only 3.29 m²/g. The morphology as shown in SEM images corresponds with the BET surface area, showing a smooth surface for RBC, a hollow surface for BBC, and a rough surface for WBC. All three biochars produced alkaline, with pH values around 10, and all have high carbon contents (47.95 - 82.1 %). Cation exchange capacity (CEC) was significantly different (p<0.05) among the biochars, being 26.70 cmol/kg for RBC, 20.7 cmol/kg for BBC, and 13.53 cmol/kg for WBC, which relates to the cations (Ca, Mg, K) and functional groups with negative charge (carboxyl, hydroxyl) present on the biochar surfaces. The highest contents of Ca, Mg and K in rice husk BC may explain its highest CEC values. Thus, although the biochars were produced by the same method, the various feedstocks lead to quite different physico-chemical properties. Ongoing work is linking these physico-chemical properties to the biochar efficiencies in terms of nitrate and ammonia capture capacities for use as fertilisers, and for adsorption of heavy metals (Zn, Cu) or water filtration, in order to design optimal biochar properties for specific applications.

Background and Objectives: The aim of this study was to determine the job-related and individual features that influence BS and depression levels among dentists working in faculties, oral and dental health centres (ODHC) and private clinics. Materials and Methods: This prospective, cross sectional study was carried out on dentists working in different regions of Turkey. Data were collected using an on-line questionnaire created using Google Forms. The questionnaire consisted of demographic data, Maslach BS Inventory (MBI) and Beck Depression Inventory (BDI) sections. Demographics were age, height, weight, marital status, blood type, gender, monthly income, income satisfaction and having enough free time. The dentists were divided into 3 groups as faculty, private clinic and ODHC according to the institutions in which they worked. Results: Of the total 290 dentists enrolled in the study, there were 172 males and 118 females with a mean age of 36.98±5.6 years. 128 of the dentists worked in faculties, 72 in private clinics and 90 in ODHCs. It was observed that women's EE scores were higher than men's (P&lt;0.05). No statistically significant difference was found between the groups when comparing BS and depression scores according to marital status and blood group (P&gt;0.05). There was no significant relationship between emotional exhaustion (EE), depersonalisation (DP), personal accomplishment (PA) and depression scores according to age, BMI and work experience, age, work experience and BMI (P&lt;0.05). It was found that the EE scores of the dentists working in the faculty and private clinic were lower than those of the dentists working in the ODHC (P&lt;0.05). Monthly income was associated with depression (r = -0.35). Conclusions: This study showed that dentists working in ODHCs had more EE. These findings suggest that there is a need for improvement in the working conditions of dentists, particularly in ODHCs.

The aim of this study was to compare the effect of using L-PRF in patients undergoing impacted lower third molar surgery with either primary or secondary closure techniques. Methods: This prospective, randomised, double-blind, split-mouth clinical trial was conducted in patients with bilateral lower impacted third molars of similar position. Primary closure was performed in group 1 and secondary closure in group 2. Group 1 closure technique was applied to one side of the patients and group 2 closure technique was applied to the other side at different times. Nine pa-tients were excluded from the study due to alveolitis and failure to attend regular control visits out of the 45 patients evaluated. Results: Of the 36 patients included in the study, 23 were female and 13 were male and the mean age was 22.42±3.36 years. The secondary closure group had lower VAS scores at hour 6 (p

The fishmeal production industry is essential for providing protein for animal feed in the aquaculture sector. However, the industry faces challenges related to energy consumption and environmental sustainability. This study evaluates the energy efficiency and environmental benefits of waste heat recovery (WHR) technologies in a fishmeal production plant in Vietnam. Data were collected from the plant between 2016 and 2022, and a specific energy consumption (SEC) indicator and a comprehensive methodology were utilized. Implementing an economizer as a WHR technology resulted in a 55.5% decrease in SEC compared to the state before installation. The enhanced energy efficiency also translated to reduced energy consumption per output unit. Moreover, the economizer contributed to annual energy savings of 4,537.57 GJ/year and cost savings of $26,474.49. Additionally, carbon dioxide (CO2) emissions associated with producing one ton of fishmeal decreased by 58.37%. These findings highlight the potential for WHR technologies to improve energy efficiency and reduce the environmental footprint of fishmeal production. The study's results provide valuable insights for practitioners and policymakers in promoting energy efficiency practices and reducing environmental impact in the industry.

The aim of this study was to evaluate the effect of two different insertion speeds at 8 different insertion torque values ranging from 25-60 during implantation in a dense polyurethane D1 bone model on the placement status and removal torque of dental implants. In this study, 50 pcf single layer polyurethane plates were used. In the study, a total of 320 implant sockets were divided into 2 groups as Group 1 (30 rpm) and Group 2 (50 rpm) in terms of insertion speed. Group 1 and Group 2 were divided into 8 subgroups as 25, 30, 35, 40, 45, 50, 55 and 60 torques. There were 20 implant sockets in each subgroup. During the implantations, implant placement status and removal torque values were assessed. There was a statistically significant difference between the 30 and 50 RPM groups in terms of overall implant placement status (p&lt;0.01). It was found that the removal torque values at 50 RPM were statistically significantly higher than those at 30 RPM (p&lt;0.01). This study showed that in dense D1 bone, the minimum parameters at which all implants could be placed at bone level were 50 torque at 30 rpm and 40 torque at 50 rpm.

Nanocomposites of TiO₂ Degussa P25 nanoparticles/activated carbon (TiO₂/AC ) were prepared at various mass ratios of (4:1), (3:2), (2:3), and (1:4) by a facile process. The effects of TiO₂/AC mass ratios on the structural, morphological, and photocatalytic properties were systematically studied in comparison with bare TiO₂ and bare AC. TiO₂ nanoparticles exhibited dominant anatase and minor rutile phases, and a crystallite size of approximately 21 nm; while AC had XRD peaks of graphite and carbon, and a crystallite size of 49 nm. The composites exhibited tight decoration of TiO₂ nanoparticles on micron-/submicron AC particles, and uniform TiO₂/AC composites were obtained as evidenced by the uniform distribution of Ti, O, and C in an EDS mapping. Moreover, Raman spectra show the typical vibration modes of anatase TiO₂ (e.g., E_1g⁽¹⁾, B_1g⁽¹⁾, E_g⁽³⁾) and carbon materials with D and G bands. The TiO₂/AC with (4:1), (3:2), and (2:3) possessed higher reaction rate constants (k) in photocatalytic degradation of methylene blue (MB) than that of either TiO₂ or AC. Among the investigated materials, TiO₂/AC = 4:1 achieved the highest photocatalytic activity with a high k of 55.2×10^-3 min^-1 and an MB removal efficiency of 96.6% after 30 min treatment under UV-Vis irradiation (120 mW/cm²). The enhanced photocatalytic activity for TiO₂/AC is due to the synergistic effect of the high adsorption capability of AC and the high photocatalytic activity of TiO₂. Furthermore, TiO₂/AC promotes the separation of photoexcited electron/hole (e^-/h⁺) pairs to reduce their recombination rate and thus enhance photocatalytic activity. The optimal TiO₂/AC composite in this study can be used for treating industrial or household wastewater with organic pollutants.

The Vu Gia - Thu Bon River Basin (VG-TB) is confronting numerous challenges related to water security (WS), particularly in the face of the impacts of climate change. These challenges manifest in salinity intrusion, altered rainfall patterns, and reduced water supply in downstream areas. To assess the current state of water security in the basin, the study employed statistical analysis methods, Process Analysis Method (PAM), SMART, and Analytic Hierarchy Process (AHP) to develop a comprehensive Assessment Framework for Water Security (AFWS) in the VG-TB. The AFWS encompasses five key dimensions, 17 indicators, and 28 variables, aligning with the UN-Water definition of water security and addressing the Sustainable Development Goal 6 (SDG6) criteria for global water sustainability. It also adheres to the Asian Development Bank's (ADB) approach to water security assessment as outlined in the Asian Water Development Outlook (AWDO) reports. This allows for the computation of a comprehensive Water Security Index (WSI) for specific regions, serving as a foundation for decision-making and policy formulation aimed at enhancing water security in the context of climate change and facilitating sustainable basin development in the future.

The study aims to evaluate the impact of organizational culture on labor efficiency at foreign-invested logistics service enterprises that are on its ways towards business sustainability. The authors develop theoretical basis on organizational culture and explore factors that contribute to organizational culture and labor efficiency; from which 03 research hypotheses are proposed. Primary data are collected from logistics businesses through questionnaires; multiple linear regresion model is used to analyze the influence of organiational culture on labor effeciency at foreign-invested logistics enterprises. Research results indicate 05 factors of organizational culture contribute positive impact on employee productivity, including employees’ trust, company ideals, leadership styles and authority division, business philosophy and mission, people’s relationship with naturual environment. Based on the research results, proposed recommendations are suggested for improving labor efficiency at foreign-invested logistics service enterprises in a sustainable way.

This study used double-bounded dichotomous-choice to estimate and analyze the factors affecting households’ willingness to pay (WTP) for water quality improvement. This study notes that households with higher income, living near polluted water source, using tap water instead of natural water, who are handicraft producers, and who have more members are willing to pay more. However, households who rarely hear about environmental pollution issues and who are offered a higher bid are more likely to refuse to pay. Solutions to improve water quality are suggested such as to raise people's awareness through communication channels and social organizations; to increase income associated with environmental protection policies; to construct wastewater treatment plants; to encourage the relocation of production establishments to industrial parks and industrial complexes; to put regulations on collection, payment and sanctions in case of not declaring and paying fees into village conventions; to promulgate circulars, and bylaws to concretize and simplify regulations and policies of the Government, Ministry of Natural Resources and Environment.

Van Wyk Grumbach syndrome refers to the development of peripheral precocious puberty, long-standing hypothyroidism, and gonadal masses; when not diagnosed, an unnecessary gonadectomy may be done; Here we present a case of a 10-year-old girl with Down syndrome, short stature, and vitiligo presented with vaginal bleeding, and a pelvic mass, in whom bilateral gonadectomy was performed. Most cases of Van Wyk Grumbach syndrome present in women, and classic hypothyroidism symptoms always precede the diagnosis; 11% of patients have Down Syndrome, sometimes tumor markers get elevated, and some develop severe symptoms (myopathy, short stature, mental delay, ascites, pericardial effusion, Cullen sign, pituitary hyperplasia, and severe anemia), that respond to levothyroxine treatment; Conclusions: Children with peripheral precocious puberty and gonadal masses, must be studied for hypothyroidism before any radical decision is made. Keywords: Puberty, Precocious; Ovarian Cysts, gonadectomy, Van Wyk Grumbach Syndrome

The objective of this study was to describe the overall pattern of morbidity and mortality of children seen at the Thai Binh Pediatric Hospital in Vietnam, with a focus on infectious diseases. A retrospective review of hospitalisation records was conducted from 1 January 2015 to 31 December 2019. Data were obtained from a total of 113,999 records. The median age of patients was 18 months, with 83.98% of patients aged <5 years. Infectious diseases accounted for 61.0% of all cases. The most prevalent diseases were lower respiratory tract infections (32.8%), followed by gastrointestinal infections (13.3%) and confirmed influenza (5.4%). Most infections were not microbiologically documented. A total of 81.4% patients received at least one antibiotic. Most patients (97.0%) were hospitalised for less than 15 days. Regarding outcomes, 87.8% patients were discharged home with a favourable outcome. 12.0% were transferred to the Vietnam National Children’s Hospital because their condition had worsened and 0.1% died. In total, infectious diseases accounted for 40.4% of deaths, followed by neonatal disorders (34.6%). Our data serves a basis for the identification of needs for diagnostic tools and for future evaluation of the effect of the targeted implementation of such facilities. Point-of-care tests, including real-time PCR assays to identify common pathogens should be implemented for more accurate diagnosis and more appropriate antibiotic use.

A study about influence of heat input on welding defects in vertical upward welding position for dissimilar material and thickness using a new variation of TIG welding torch is done with support of advanced inspection methods SEM and EBSD. With vertical upward welding position, control heat input plays an important role to keep the weld stabilization without defects. On the other hand, TIG welding process using a conventional TIG torch (conventional TIG welding process) has low efficiency and it is difficult to control heat input with high accuracy. So, it is considered that using conventional TIG torch is still a challenge for welding thin plates. In this case, a new variation of TIG torch has been developed. This torch used a constricted nozzle to improve plasma arc characteristics. As a result, it can control efficiently the heat input to prevent the excessive or insufficiency for joining thin sheets. For evaluation of welding quality, advanced examination methods SEM and EBSD were applied to directly observe the welding defects. From the results, the formation mechanism of blowhole inside weld zone in case of welding dissimilar material and thickness was discussed. It is pointed out that when sufficient welding current, the change from weld zone to base metal is uniform, no welding defects such as blowhole was seen. However, in case of low welding current, the thinner base metal is insufficient fusion and the change between weld zone and base metal is not uniform. The blowhole was observed at SS400 material side.

α-amylase inhibitors (aAIs) have been proved efficient for the management of type 2 diabetes. This study aimed to search the potential aAIs produced by microbial fermentation. Among various bacterial strains, Pseudomonas aeruginosa TUN03 was found as a potential aAI - producing strain, and shrimp heads powder (SHP) was screened as the most suitable C/N source for fermentation. P. aeruginosa TUN03 exhibited the highest aAIs productivity (3100 U/mL) in the medium containing 1.5% SHP with the initial pH of 7-7.5, and fermentation was performed at 27.5 °C in 2 days. Further, aAIs compounds were investigated for scale-up production in a 14 L – bioreactor system, and the results highlighted high yield (4200 U/mL) in much shorter fermentation time (12 h) compared to fermentation in flasks. The bioactivity-guided purification resulted in the isolation of one major target compound. This active compound was confirmed as hemi-pyocyanin (HPC), with good purity, via using high-performance liquid chromatography and gas chromatography-mass spectrometry. Notably, HPC demonstrated potent activity comparable to acarbose, a commercial antidiabetic drug; this is the first-ever report of aAI activity of HPC. The docking study indicated that HPC inhibits α-amylase via binding to amino acid Arg421 at the biding site on enzyme α-amylase with good binding energy (-9.3 kcal/mol) and creating two linkages of H-acceptor.

Vip3 proteins are increasingly used in insect control in transgenic crops. To shed light on the structure of these proteins, we used the approach of trypsin fragmentation of mutants altering the conformation of the Vip3Af protein. From an alanine scanning on Vip3Af, we selected mutants with an altered proteolytic pattern. Based on the protease digestion patterns, their effect on oligomer formation, and theoretical cleavage sites, we generated a map of the Vip3Af protein with five domains, which match some of the domains proposed independently by two in silico models. Domain I ranges from aa12-198, domain II from aa199-313, domain III from aa314-526, domain IV from aa527-668 and domain V from aa669-788. The effect of some of the mutations on the ability to form a tetrameric molecule revealed that domains I-III are required for tetramerization, while domain V is not. The involvement of domain IV in the tetramer formation is not clear. Some mutations distributed from near the end of domain I up to the end of domain II affect the stability of the first three domains of the protein and negatively impact oligomerization upon trypsin treatment. Because of the high sequence similarity among Vip3 proteins, we propose that our domain map can be extended to many other members of the Vip3 family of proteins.

Burn injuries have profound implications for aesthetics, functionality, and patient survival. Umbilical cord lining mesenchymal stem cells (SCL-MSCs) have emerged as a potential therapeutic approach for burn wounds due to their easy isolation, favorable differentiation capabilities, and low immunogenicity. This study aimed to evaluate the growth characteristics of SCL-MSCs and their effectiveness in treating burn wounds. Mechanical isolation was employed to extract mesenchymal stem cells from the umbilical cord lining membrane. The isolated cells underwent characterization, including analysis of HLA-E, G, and DR expression, and assessment of immunogenicity against rabbit antigens using ELISA. A rabbit model was utilized to administer burn treatment. SCL-MSCs exhibited typical morphology of mesenchymal stem cells and demonstrated robust proliferation. These cells expressed CD90, HLA-E, and HLA-G markers while lacking HLA-DR expression. Intact cells and supercrushed cell fluid displayed minimal and unstable immunogenicity. SCL-MSCs exhibited remarkable differentiation potential toward fibroblast lineages, with differentiated fibroblasts showing elevated collagen production and efficient sheet formation. In the experimental rabbit model, burn wounds covered with SCL-MSC tegaderm material plates exhibited superior healing compared to controls. The stem cell material plate area demonstrated reduced inflammatory cell counts (P &lt; 0.01) and increased fibroblast count, neovascularization, and mitotic index (P &lt; 0.01). These findings highlight the potential of SCL-MSCs as a valuable resource for burn wound research and treatment.

Background: Strongyloidiasis, a neglected disease caused by intestinal nematodes of the genus Strongyloides, is endemic to tropical and subtropical areas such as Vietnam. The morphological diagnosis of larvae by Hara Mori culture technique and microscopicare are considered the standard diagnostic procedures in the endemic areas of Strongyloides spp. However, they could only identify the genus, not the species of Strongyloides. DNA-molecular techniques which are highly sensitive and more cost-effective have been increasingly utilized in detection of Strongyloides species. This study aims to determine prevalence and the species of Strongyloides among resident population in Duc Hoa district, Long An province, Southern Vietnam. Methods: A cross-sectional study was conducted using 1,190 stool samples collected in Duc Hoa district, Long An province, Vietnam, from July, 2017 to November 2018. The stool specimens were transported to the Laboratory of Medical Parasitology, Pham Ngoc Thach University of Medicine within two hours of collection at an appropriate temperature of 25 oC. All samples were stored at 2 - 8°C and processed within 48 hours for microscopic examination. Molecular detection was carried out at Laboratory of Molecular Biology, Pham Ngoc Thach University of Medicine, Hochiminh city, VietNam. Results: Of the 1,190 samples tested, Strongyloides spp. larvae were detected in 79 specimens (6.6%) by two classical parasitological methods, namely direct microscopy and the modified Harada-Mori filter paper culture. DNA was extracted from 70 of the 79 samples of Strongyloides spp. larvae, which was subsequently characterized by real-time PCR amplification of the 18S and 28S regions of the rDNA gene. The results showed that 97.1% of the DNA samples were S. stercoralis, 2.9% were co-infections with S. ratti and S. stercoralis, and 2.9% belonged to S. ratti. For all 14 isolates, nucleotide sequencing was compared with other human pathogenic species of Strongyloides whose sequences are available in GenBank. The identity of 12/14 sequences were confirmed as S. stercoralis with a high level of similarity (91.3% - 100%) and over 98% for S. ratti. Between the two co-infection samples, the higher similarity belonged to S. stercoralis. Conclusion: A molecular amplification of small subunit ribosome RNA followed by sequence analysis has been proved to be a suitable method for discrimination of Strongyloides spp. retrieved from stool samples.

African swine fever (ASF) is a lethal and highly contagious transboundary animal disease with the potential for rapid international spread. Currently, there is no ASF vaccine commercially available. All infected animals must be isolated and culled immediately upon confirmation of the presence of the virus. Works leading to the rational development of protective ASF vaccines are urgently needed. Here, we generated a safe and efficacious live-attenuated vaccine (LAV) VNUA-ASFV-LAVL2 by serial passaging of a field isolate (VNUA-ASFV-05L1, genotype II) in porcine alveolar macrophage (PAMs, 65 passages) and an immortalized porcine alveolar macrophage cell line (3D4/21, 55 passages). VNUA-ASFV-LAVL2 can efficiently replicate in both PAMs and 3D4/21 cells. It provides 100% protection, even with the low dose of 10^2 HAD50, for the vaccinated pigs against the challenge of contemporary pandemic ASFV field isolate. Pigs vaccinated with this LAV at a dose range of 10^2 to 10^5 HAD50 remained clinically healthy during both the 28-day observation period of immunization and the 28-day observation period of challenge. VNUA-ASFV-LAVL2 was completely eliminated from blood by 28 days post inoculation (DPI), and from feces or oral fluids by 17 DPI. It remained a safe, stable, and attenuated phenotype after five passages in pigs. Consistently high levels of ASFV-specific IgG antibodies and significant cellular immunity were detected in vaccinated pigs before the ASFV challenge. These results indicate that the VNUA-ASFV-LAVL2 strain is a safe and efficacious LAV against the genotype II ASFV strain responsible for current ASF outbreaks in Asia.

In order to develop novel botanical insecticides, the joint action of Ligusticum chuanxiong oil (LCO) and lemongrass oil (LO) against Aphis citricola van der Goot was determined systematically indoors and outdoors. The chemical profiles of LCO and LO as determined by gas chromatography- mass spectrometry analysis revealed that main compounds from LCO were Z-Ligustilide (44.58%) and Senkyunolide A (26.92%), and that of LO were geranial (42.16%) and neral (32.58%), respectively. The mixture of LCO and LO showed significant synergy against A. citricola, with a common-toxicity coefficient (CTC) value of 221.46 at the optimal ratio of LCO to LO (4: 1, w/w). Based on the results of solvents and emulsifiers screening, L. Chuanxiong oil · Lemongrass oil 20% emulsifiable concentrate (20% LCO · LO EC) was developed, which was confirmed to meet the requirements of a commercial pesticide by quality test. Field trials indicated that the insecticidal activity of the diluted 20% LCO · LO EC (1000 fold dilution) was comparable to conventional pesticide (20% imidacloprid EC) on A. citricola 7 days after application. Thus, the mixture of LCO and LO has the potential to be further developed as a botanical pesticide.

Skin image analysis using artificial intelligence (AI) has recently attracted significant research interest, particularly for analyzing skin images captured by mobile devices. Acne is one of the most common skin conditions with profound effects in severe cases. In this study, we developed an AI system called AcneDet for automatic acne object detection and acne severity grading using facial images captured by smartphones. AcneDet includes two models for conducting two tasks: (1) a Faster R-CNN-based deep learning model for the detection of acne lesion objects of four types including blackheads/whiteheads, papules/pustules, nodules/cysts, and acne scars; and (2) a LightGBM machine learning model for grading acne severity using the Investigator’s Global Assessment (IGA) scale. The output of the Faster R-CNN model, i.e., the counts of each acne type, were used as input for the LightGBM model for acne severity grading. A dataset consisting of 1,572 labeled facial images captured by both iOS and Android smartphones was used for training. The results show that the Faster R-CNN model achieves a mAP of 0.54 for acne object detection. The mean accuracy of acne severity grading by the LightGBM model is 0.85. With this study, we hope to contribute to the development of artificial intelligent systems that are able to help acne patients understand more about their conditions and support doctors in acne diagnosis.

Coastal erosion is threatening the infrastructures of coastal community at the Ma River mouth in Thanh Hoa province, Vietnam. When coastal erosion happens, people try to prevent it by emergency solutions like hard structures. However, this approach usually leads to more severe problem since the mechanism for coastal erosion is not investigated and understood properly. In this study the long-term configuration of Ma River mouth in Thanh Hoa Province, Central Vietnam has been investigated using Landsat imagery from 1987 to 2023. An analytical solution of one-line model for shoreline change was also employed to calculate the sand discharge from Ma River as well as the diffusion coefficient for sand transported along-shore by breaking waves. There was an asymmetric configuration of the Ma River mouth during the last 37 years. The sand supply from the Ma River is around 350,000 m3/year. This amount of sand is going mainly to the northern beach of the Ma River delta (from 55% to 75%). The asymmetric morphology of the Ma River mouth delta is the trigger for severe coastal erosion reported recently. This study provides a quick and easy method to investigate the morphological change of cuspate deltas where measured data is limited.

Leigh Van Valen was an American evolutionary biologist who made major contributions to evolutionary theory and is particularly remembered by his groundbreaking paper "A New Evolutionary Law" (1973) where he provided evidence from fossil record data that this law maintains that the probability of extinction within any group remains es­sentially constant through time. In order to explain such unexpected result, Van Valen formulated a very influential idea that he dubbed the "Red Queen hypothesis". It states that the constant decay must be a consequence of evolutionary interactions among connected species within ecological networks. In Van Valen's picture, species do not merely evolve: they also coevolve with other species. As a consequence, when thinking in adaptation to an external environment, the other species must be considered as part (may be a major part) of such external world. Van Valen's law provided the first complex systems theory of coevolutionary dynamics and inspired a whole range of theoretical and experimental developments and scholars from very diverse fields, from economics to physics. In that respect, Leigh Van Valen's contribution percolated far beyond its original formulation. Red Queen arms races are nowadays considered a widespread feature of complex adaptive systems.

This study investigates how the determinants including risk preference affect farmers’ decision to adopt SLM practices in upland areas of Vietnam. Empirical data collected through in-depth interviews with 200 farmers in Na Ri district, Bac Kan province were used. The factors affecting SLM adoption of farmers in Na Ri district were examined by the 2SLS or IV-Probit model. The estimated 2SLS regression indicated that there is a set of factors affecting SLM adoption, namely, relative risk aversion, farming experience, farm size, knowledge of SLM, membership in farmers’ organization, number of labors, and slope of farm land. Specifically, relative risk aversion had a negative effect on SLM practices adoption. The farmers who are less risk averse are more likely to adopt more SLM practices. This implies that reducing farmer’ risk exposure could promote SLM practices. This result is also helpful for policymakers to understand farmers’ behaviors and promote the diffusion of SLM practices across regions on a large scale.

We show that the van der Waals gas does not exhibit just the celebrated liquid-gas 1 transition but also a quantum-classical one. We study the issue with reference to the LMC statistical 2 complexity and in relation to the order-disorder contrast.

Logistics industry has been found to be among the key sources of carbon emission. In Vietnam logistics industry, there is a considerable difference between the number of foreign and Vietnamese firms as well as the proportion of markets that they are taking. This study is to research the low-carbon emission measures conducted by domestic and foreign invested logistics service providers (LSPs) and compare the results of the two groups. Both qualitative and quantitative approaches are applied. Literatures in relevant fields are reviewed and expert opinions are taken for structuring a questionnaire which was later distributed to 279 LSPs, with 166 returned and 159 being valid for data calculation. The results imply that there are differences in extension of applications of low-carbon practices between foreign and domestic firms. Except for transport mode switch and energy-saving lighting, the other practices witness that adoption levels of foreign LSPs are higher than their counterparts, which is possibly thanks to their global operation, more comfortable capital resources and awareness level of green initiative necessity. In conclusion, a comparison between the application conducted by foreign-invested firms and domestic ones, which has not been investigated before, was made.

Extracts of Cordyceps militaris which possess the bioactive capacity such as antimicrobial activity and DPPH-free radical scavenging capacity, are applied to the serum product. This finished serum product has been evaluated the in vitro bioactivity and the stability with expect to find out a good extract with a suitable percentage used for serum product as natural materials on preservatives and antioxidation.

China promotes nature-based solutions (NbS) as key approaches to addressing climate change, ecosystem damage, and biodiversity loss. However, indigenous and local knowledge (ILK), which is recognized by international scholars as an essential element of successful NbS, has not been thoroughly studied in the Chinese context. By conducting a comprehensive review of Chinese central governmental policies and semi-structured interviews with typical cases, this study finds out diversified sources of ILK and five pathways of ILK integration, including education, supervision, participation, knowledge preservation, and knowledge adoption. An increasing emphasis on community engagement has been driven by central policies such as the ecological civilization, carbon peaking and carbon neutrality goals. From a practical perspective, consistent core ideas of ILK exist in selected typical Chinese cases and studies in other countries, namely co-existence and reciprocity with nature. While supportive central policies can set the scene, ILK integration could not be realized without local governmental endorsement, context-based implementation, and long-term multi-stakeholder participation. Furthermore, this study also figures out a potential deficiency in terms of realizing effective ILK integration in mainstream and conventional practices, which can be further investigated by future studies.

Global agriculture has been forced to increase food production to feed the growing human population, while confronting various environmental obstacles such as global warming, resistance to pathogens, and constraints on arable land caused by soil salinity, drought, rising sea level, saltwater intrusion, and urbanization. Regarding abiotic stresses, salinity is a worldwide problem for agricultural production. Many efforts, therefore, have been made to cope with the environmental challenges, however, the progress of salinization, which is mainly caused and accelerated by anthropogenic activities, is likely faster than our progress in finding ways to deal with this problem. In addition, drought represents a global threat to the production of major crops. In addition, pests and pathogens cause significant crop losses and diminish global food security. Among the various strategies that have been investigated and applied in plant science, antimicrobial peptides derived from plants have caught widespread attention from scientists since these peptides exhibit beneficial biological activities. In agricultural science, there have been reports on the roles of antimicrobial peptides with active properties against biotic and abiotic stresses. Non-specific plant lipid transfer proteins, thionins, systemins, defensins, cyclotides, and heveins-like antimicrobial peptides are common antimicrobial peptides that have been found to be involved in the defense system against fungi and insect pests. Based on their potential ability to protect crops from pests, bacteria, and pathogenic fungi, the use of antimicrobial peptide genes in creating transgenic plants has been largely conducted during the last decades, and these studies have obtained positive results against the growth of fungi and bacteria. This review will focus on the latest progress in studies of antimicrobial peptides related to biotic and abiotic stress tolerance in plants. We will also update the current progress in the development of antimicrobial peptide-based transgenic crops.

The aim of this study was to evaluate the use of a flexible synthetic polymer bone graft to provide implant stability in the absence of implant stability during implant placement in a dense cortical bone model. Sockets were prepared on polyurethane blocks according to the standard implant socket drilling protocol in the control group, both oversizing and deepening in group 2, and oversizing only in group 3. In groups 2 and 3, flexible synthetic polymer bone grafts were placed in the sockets prior to implant placement. The implants were placed at bone level in all groups. The highest torque value obtained was recorded as the insertion torque. 75 implant sites in 3 groups were included in the study. The torque values of the implants in the control group were significantly higher than those of the implants with the oversized and deepened sockets and the oversized-only sockets (p&lt;0.05; p&lt;0.01).The torque values of the implants with the oversized and deepened sockets were significantly higher than those of the implants with the oversized-only sockets (p&lt;0.01). In this study, flexible synthetic polymer bone graft was shown to be effective in achieving implant stability in the management of implants with loss of primary stability.

This study examines the Willingness-To-Pay (WTP) of consumers and the determinants of eco-labeling for the organic cocoa powder produced in the Dong Nai UNESCO Biosphere Reserve (DNBR), Southern Vietnam. Eco-labels are designed according to Tiers of eco-labeling for biosphere reserves (BR) introduced by UNESCO include BR Destination (Tier 1), BR Quality Label (Tier 2), and Professional Certification Label (Tier 3). Questionnaires are delivered to 203 customers in the DNBR and nearby places, such as Dong Nai and HCMC. This study employs a hybrid approach using descriptive statistics, ANOVA test, and Partial Least Squares Structural Equation Model (PLS-SEM). The results indicate that gender and educational level have a positive effect on consumers' preferences. Customers are willing to pay more for cocoa powder with an eco-label than one with an organic label. Perceived food safety and product knowledge lower customers’ WTP, whereas agricultural environment and pricing concerns increase it. Tier 2 is suggested for labeling cocoa powder in the DNBR. The DNBR Management Board, together with the federal and provincial governments, should all follow a similar certification process. Increased eco-label awareness is crucial for the future of environmentally responsible shopping and responsible business practices.

In this short paper we study some properties of the lines associated with van Aubel’s theorem in the special case when squares are replaced with equilateral triangles constructed on the sides of an arbitrary quadrilateral.

Introduction: Hemostatic dysfunction during extracorporeal membrane oxygenation (ECMO) due to blood-circuit interaction and the consequences of shear stress by flow rates lead to rapid activation of the coagulation cascade and thrombus formation in the ECMO system and blood vessels. In this study, we aimed to identify the incidence and risk factors for cannula-associated arterial thrombosis (CaAT) post-decannulation. Methods: A retrospective study of patients undergoing arterial cannula removal following ECMO. We evaluated the incidence of CaAT and compared clinical characteristics, pre-ECMO severity, and daily hemostasis parameters in patients with and without CaAT. Multivariate analysis revealed the risk factors for CaAT. Results: Forty-seven patients requiring venoarterial ECMO or hybrid methods were recruited to be screened for thrombosis. The median SOFA score was 11 (8-13). CaAT occurred in 29 patients (61.7%), with thrombosis in the superficial femoral artery accounting for 51.7%. Limb ischemia complications in the group with CaAT was 17.2%. In multivariate analysis, an ECMO flow rate of 100 mL/min was determined to be the independent factor for CaAT with an OR of 0.84 (95% CI, 0.73–0.95, p=0.008). Conclusion: In patients successfully weaned from ECMO, the incidence of CaAT was 61.7%. Our study found that a low-flow rate of ECMO was an independent risk factor for CaAT.

The coastline in the Ca Mau and the Kien Giang provinces of the Vietnamese Mekong Delta has been severely eroded in recent decades. Pile-Rock Breakwaters (PRBW) are one of the most widely adopted structures for controlling shoreline erosion in this region. These structures are effective for wave energy dissipation, stimulating sediment accumulation, and facilitating the restoration of mangrove forests. These breakwaters are generally considered to be best-engineering practice however there is currently insufficient scientific evidence with regard to specific structural design aspects. This can lead to PRBW structures being compromised when deployed in the field. This study uses a physical model of a PRBW in a laboratory to investigate several design parameters, including crest width and working states (i.e. submerged, transition, and emerged), and investigates their relationship with the wave transmission coefficient, wave reflection coefficient, and wave energy dissipation. To investigate these relationships further, empirical formulas were derived for PRBWs under different sea states and crest widths to aid the design process. The results showed that PRBW width had a significant influence on the wave energy coefficients. The findings revealed that the crest width of the breakwater is inversely proportional to the wave transmission coefficient (K_t) under the emerged state. The crest width is also proportional to the wave reduction efficiency and wave energy dissipation in both working states (i.e., submerged and emerged states). The front wave disturbance coefficient (K_f) was found to be proportional to the wave reflection coefficient, and the wave height in front of the structure was found to increase by up to 1.4 times in the emerged state. The wave reflection coefficient requires special consideration to reduce the toe erosion in the structure. Lastly, empirical equations including linear and non-linear formulas were compared with previous studies for different classes of breakwaters. These empirical equations will be useful for understanding the wave transmission efficiency of PRBWs. The findings of this study provide important guidance for PRBW design in the coastal area of the Mekong Delta.

The study aimed to compare the cardiovascular benefits of Omega-3 Polyunsaturated Fatty Acids from fish oil versus krill oil in different forms and dosages. Following PRISMA 2015, data analysis with R software, and databases were searched from 1993 to 2023, (ID PROSPERO: CRD42024502338). Sixty high-quality studies were analyzed, covering various forms of fish oil and krill oil at different dosages (fish oil (ethyl ester-EE, triglyceride-TG, re-esterified triglycerides-rTG, capsules, emulsion-EM); krill oil (phospholipid/free fatty acid-PL/FFA, high concentration phospholipid-HPL, low concentration phospholipid-LPL)). Meta-analysis revealed that krill oil with phospholipid/free fatty acid at doses 2000-2900 mg effectively lowered triglycerides, while fish oil in ethyl ester form at doses above 3000 mg significantly reduced total cholesterol. Fish oil in triglyceride form at doses 2000-2900 mg and other variations positively impacted HDL-C levels. Fish oil in EE form above 3000 mg and triglyceride form below 2000 mg notably reduced LDL-C. However, there was limited effectiveness observed for other interventions. Analysis for LDL-C exhibited publication bias, while other parameters demonstrated reliability (Egger's test). In conclusion, krill oil - PL/FFA, Fish oil - EE above 3000 mg, Fish oil - TG 2000-3000 mg, and fish oil - rTAG 300-1900 mg effectively in reducing heart risk patients.

Tidal inlets with attached sand spits are a very common coastal morphology. Since the evolution of the sand spits along the coastline have greatly affected on the social-economic development of local coastal areas. However, previous studies mainly focused on the sand spits which are usually in the scales of hundred meters in width. Therefore, in this study, morphological change of a smaller and unexplored sand spit located in the west coast of Phu Quoc Island, will be investigated. It was found that there is a seasonal variation in the evolution of the sand spit at Song Tranh Inlet. The Longshore sediment transport rates (LSTR) along the spit are in the order from 104 to 105 m3/year. LSTRs of fourteen inlets in the literature were reviewed and the LSTRs at Song Tranh Inlet are higher than half of the LSTRs along the fourteen reviewed inlets. This study aims at contrib-uting to the growing literature on sand spit morphological changes as well as the sustainable coastal management for Phu Quoc Island which is well known as the Pearl Island of Vietnam.

Allanite minerals are the principal host of REEs in the Sin Quyen, Iron Oxide Copper Gold (IOCG) type deposit. The studied allanites have concentrations of: REE (14-27 wt%), Ca (9-16 wt%), Al (8-19 wt%), Si (26-34 wt%) and Fe (12-21 wt%). Two populations of allanite are documented, the first is texturally older probably related to the Ca-K alteration (second stage of crystallization). This population has higher REE concentrations ranging from 20 to 27 wt%, and the second population texturally younger has lower total REE concentration ranging from 14 to 19.9 wt%, which occur as a rim surrounding the older and likely arose during the K alteration with Cu-Au mineralization (third crystallization). Differences between the two allanite populations are documented by both optical properties and analysis of their chemical composition. The last parameter indicate that the studied allanites belong to the Ce-La-ferriallanite family, with low HREE with an average of 0.21 wt.%. Temperature 355ºC which was calculated using value of δ34S isotopes is interpreted as a temperature of the second crystallization stage of allanite. The pressure of crystallization solution was calculated and is ranging from 0.98 to 5.88 MPa.

A complete MAPLE procedure is designed to implement effectively an algorithm for approximating the trigonometric functions. The algorithm gives a piecewise polynomial approximation on an arbitrary interval, presenting a special partition that we can get its parts, subintervals with ending points of finite rational numbers, together with corresponding approximate polynomials. The procedure takes a sequence of pairs of interval-polynomial as its output that we can easily explore in some useful ways. Examples on calculating approximate values of the sine function with arbitrary accuracy for both of rational and irrational arguments as well as drawing the graph of the piecewise approximate functions will be presented. Moreover, from the approximate integration of integrands of the form $x^m\sin x$ on $[a,b]$, another MAPLE procedure is proposed to find the desired polynomial estimates in norm for the best $L^2$-approximation of the sine function in the vector space $\mathcal{P}_{\ell}$ of polynomials of degree at most $\ell$, a subspace of $L^2(a,b)$.

Diseases pose a significant and pressing concern for the sustainable development of the aquaculture sector, particularly as their impact continues to grow due to climatic shifts such as rising water temperatures. While various approaches, ranging from biosecurity measures to vaccines, have been devised to combat infectious diseases, their efficacy is disease- and species-specific and contingent upon a multitude of factors. The field of genetics and genomics offer effective tools to control and prevent disease outbreaks in aquatic animal species. In this study, we present the key findings from our recent research, focusing on the genetic resistance to three specific diseases: White Spot Syndrome Virus WSSV) in white shrimp, Bacterial Necrotic Pancreatitis (BNP) in striped catfish and skin fluke (a parasitic ailment) in yellowtail kingfish. Our investigations reveal that all three species possess substantial heritable genetic components for disease resistant traits, indicating their potential responsiveness to artificial selection in genetic improvement programs tailored to combat these diseases. Also, we observed a high genetic association between disease traits and survival rates. Through selective breeding aimed at enhancing resistance to these pathogens, we achieved substantial genetic gains, averaging 10% per generation. These selection programs also contributed positively to the overall production performance and productivity of these species. Although the effects of selection on immunological traits or immune responses were not significant in white shrimp, they yielded favourable results in striped catfish. Furthermore, our genomic analyses, including shallow genome sequencing of pedigreed populations, enriched our understanding of the genomic architecture underlying disease resistance traits. These traits are primarily governed by a polygenic nature, with numerous genes or genetic variants, each with small effects. Leveraging a range of advanced statistical methods, from mixed models to machine and deep learning, we developed prediction models that demonstrated moderate to high levels of accuracy in forecasting these disease-related traits. In addition to genomics, our RNA-seq experiments identified several genes that undergo upregulation in response to infection or viral loads within the populations. Preliminary microbiome data, while offering limited predictive accuracy for disease traits in one of our studied species, underscore the potential for combining such data with genome sequence information to enhance predictive power for disease traits in our populations. Lastly, this paper briefly discusses the roles of precision agriculture systems, AI algorithms, and outlines the path for future research to expedite the development of disease-resistant genetic lines tailored to our target species. In conclusion, our study underscores the critical role of genetics and genomics in fortifying the aquaculture sector against the threats posed by diseases, paving the way for more sustainable and resilient aquaculture development.

The Van der Pol oscillator is a chaotic non-linear system. Small perturbations in initial conditions may result in wildly different trajectories. Because of its chaotic nature, controlling, or forcing, the behavior of a Van der Pol oscillator is difficult to achieve through traditional adaptive control methods. Connecting two Van der Pol oscillators together where the output of one oscillator, the driver, drives the behavior of its partner, the responder, is a proven technique for controlling the Van der Pol oscillator. Deterministic AI (DAI) is an adaptive feedback control method that leverages the known physics of the Van der Pol system to learn optimal system parameters for the forcing function. We assessed the performance of DAI employing three different online parameter estimation algorithms. Our evaluation criteria include mean absolute error (MAE) between the target trajectory and the response oscillator trajectory over time. RLS with exponential forgetting (RLS-EF) had the lowest MAE overall, with a 2.46% reduction in error. However, another method was notable. Least Mean Squares with normalized gradient adaptation (LMS-NG) had worse initial error in the first 10% of the simulation, but after that point had consistently better performance. We found that over the last 90% of the simulation, DAI with LMS-NG had a 48.7% reduction in MAE compared to feedforward alone.

Bacillus veleznesis RB.EK7 was recently found as a potent rhizobacterial strain for effective management of black pepper root-knot nematodes. This work aimed to produce, purify, and elucidate the chemical structures of antinematode compounds (ANCs). Concerning cost-effectiveness and environmental issues, this study used organic wastes for the bioproduction of ANCs. Among various substrates, shrimp shells powder was the most suitable carbon/nitrogen source to produce ANCs. The fermentation process for enhancement of antinematode activity was investigated. The targeting ANCs were purified from the fermented culture broth, and their structures were elucidated. Two active compounds were thymine (1) and hexahydropyrrolo [1,2-a]pyrazine-1,4-dione (2). Notably, for the first time, these purified compounds showed potential and moderate anti- J2 nematodes and anti-eggs hatching, respectively. The docking study results indicated that the potent antinematode effect of these compounds may be possibly due to the inhibition of the targeting enzyme acetylcholinesterase. The data of this work suggest that organic waste SSP can be potentially reused for the production of thymine and hexahydropyrrolo [1,2-a] pyrazine-1,4-dione with promising use for the management of black pepper nematodes.

In order to solve the problem of the poor oil displacement effect of high molecular weight alkali/surfactant/polymer (ASP) solution in low permeability reservoirs, Daqing Oilfield uses a partial quality tool to improve the oil displacement effect in low permeability reservoirs. Without changing the oil displacement capability of high molecular weight ASP solution in high permeability oil layers, the ASP solution is actively sheared in low permeability oil layers by using a partial quality tool to increase the injection capability of the solution and improve the overall oil recovery. In order to study the ability of the partial quality tool to improve the oil displacement effect, firstly, the matching degree of high molecular weight ASP solution to low permeability cores is studied, and the ability of quality control tools to change the molecular weight is studied. Then, experimental research on the pressure and oil displacement effect of high molecular weight ASP solution before and after the actions of the partial quality tool is carried out. The results show that ASP solutions with molecular weights of 1900 × 104 and 2500 × 104 have a poor oil displacement effect in low permeability reservoirs. After the action of the partial quality tool, the injection pressure is reduced by 5.22 MPa, and the oil recovery is increased by 7.79%. The injection pressure of the ASP solution after shearing by the partial quality tool is lower than that of the ASP solution with the same molecular weight and concentration without shearing, but the oil recovery is lower. On the whole, the use of the partial quality tool can obviously improve the oil displacement effect in low permeability reservoirs.

INTRODUCTION: The purpose of the study was to determine (a) the overall preclinical character; (b) the cumulative cutoff values and the risk ratio, and (c) the factors associated with severity by a unidimensional and multidimensional analysis on 2173 Sars-Cov2 patients. METHODS: The machine learning study population consisted of 2173 patients (1587 mild and non symptoms patients, 377 moderate patients, 209 severe patients). The status of the patients was recorded from September 2021 to March 2022. RESULTS: The Covid19 Severity directly links with a significant correlation to Age, Score index of the chest X-ray, percentage and quantity of neutrophils, Albumin, C reactive protein, and ratio of Lymphocytes. Their important cut off values (from regression analysis) respectively are: 77.56 years old (the mild-moderate group), 5.53 (the mild-moderate group) and 10.51 (the moderate-severe group), 84.80% (the mild-moderate group) and 87.74%(the moderate-severe group), 11.77G/L (the moderate-severe group), 29.73g/L (the moderate-severe group), 7.46mg/dL (the mild-moderate group), 6.32% (the moderate-severe group). Their significant (p<0.0001) R score correlation with the severity of Covid19, are: 0.44, 0.52 and 0.52, 0.33 and 0.44, 0.42, -0.43, 0.40, -0.41. Their significant risk ratio (p<0.00001) from the meta-analysis, respectively are: 4.19 [3.58-4.95], 3.29 [2.76-3.92] and 3.03 [2.4023;3.8314], 3.18 [2.73-3.70] and 3.32 [2.6480;4.1529], 3.15 [2.6153;3.8025], 3.4[2.91-3.97], 0.46 [0.3650;0.5752] (p<0.00001), 0.34 [0.2743;0.4210]. The pair ALT – Leucocytes and Transferrin – Anion Chloride get the most important correlation shift. ALT – Leucocytes show the important negative link (R=-1, p<0.00001) in the mild group to the significant positive correlation in the moderate group (R=1, p<0.00001). Transferrin–anion Chloride has an important positive association (R=1, p<0.00001) in the mild group with a significant negative correlation in the moderate group (R=-0.59, p<0.00001). The network map and HCA show that in the mild-moderate group, the closest neighbors with the Covid19 severity are ferritins, Age. Then there is C-reactive protein, SI of X-ray, Albumin, and Lactate dehydrogenase, which are the next close neighbors of these three factors. In the moderate-severe group, the closest neighbors with the Covid19 severity are Ferritin, Fibrinogen, Albumin, the quantity of Lymphocytes, SI of X-ray, white blood cells count, Lactate dehydrogenase, and quantity of neutrophils. CONCLUSIONS: Complete multidimensional study in 2173 Covid19 patients in Vietnam shows the whole picture of all the preclinical factors, which may become the clinical reference marker for surveillance and diagnostic management

This research investigates the potential application of generative language models, especially ChatGPT, in aviation safety analysis as a means to enhance the efficiency of safety analyses and accelerate the time it takes to process incident reports. In particular, ChatGPT was leveraged to generate incident synopses from narratives, which were subsequently compared with ground truth synopses from the Aviation Safety Reporting System (ASRS) dataset. The comparison was facilitated by using embeddings from Large Language Models (LLMs), with aeroBERT demonstrating the highest similarity due to its aerospace-specific fine-tuning. A positive correlation was observed between synopsis length and their cosine similarity. In a subsequent phase, human factor issues involved in incidents as identified by ChatGPT were compared to human factor issues identified by safety analysts. A concurrence rate of 61% was found, with ChatGPT demonstrating a cautious approach towards attributing human factor issues. Finally, the model was used to attribute incidents to relevant parties. As no dedicated ground truth column existed for this task, a manual evaluation was conducted. ChatGPT attributed the majority of incidents to the Flight Crew, ATC, Ground Personnel, and Maintenance. This study opens new avenues for leveraging AI in aviation safety analysis.

Background: Educating college students about the importance of good sleep habits could lead to the adoption of healthier sleep routines, including sufficient sleep duration and sleep quality. The current pre-post study examines the impact of completing a sleep education program called “Sleep 101” on (1) sleep hygiene practices, (2) sleep quality, and (3) weekday and weekend sleep behaviors among college students. “Sleep 101” is an interactive online course developed to educate college students about the importance of sleep by addressing basic sleep physiology, the impact of sleep on mood, academic and physical performance, the interactions between sleep and various substances, and common sleep disorders. Methods: 338 college students were recruited from a midsized public university in the US and invited to participate in “Sleep 101”, of which 25 participants completed the baseline and post-intervention questionnaire. The Sleep Hygiene Index (SHI) was utilized to evaluate sleep hygiene practices, while standard questions were employed to assess weekday and weekend sleep behaviors and overall sleep quality. Results: Those who completed the study demonstrated a significant increase in weekday sleep duration and were less likely to engage in negative prior bedtime activities. In addition, 40% of those who completed baseline and post-intervention assessments noticed improvements in their sleep quality. Conclusion: These findings suggest that a brief online program is beneficial in improving sleep behaviors among college and could be a scalable approach to addressing current sleep issues and preventing future sleep problems in college students.

Lean is one of the systematic approach to achieve higher value for organizations through eliminate non-value-added activities. It is an integrated set of tools, techniques, and principles designed to optimize cost, quality and delivery while improving safety. In Vietnam, industry waste management and treatment has become serious issue. The aim of this research is to present the effective of Lean application for industrial wastes collecting and delivery improvement. Through a case study, this paper showed the way of Lean tools and principles applied for wastes management and treatment such as Value Stream Mapping, Pull system, Visual Control, and Andon.... to get benefit on both economic and environment. In addition, the results introduced a good experience for Vietnamese enterprises in cost saving and sustainable development in waste management.

Leaf color mutants (LCMs) are important resources for studying diverse metabolic processes such as chloroplast biogenesis and differentiation, pigments’ biosynthesis and accumulation, and photosynthesis. However, in Dendrobium officinale, LCMs are yet to be fully studied and exploited due to the unavailability of reliable RGs (reference genes) for qRT-PCR (quantitative real-time reverse transcription PCR) normalization. Hence, this study took advantage of previously released transcriptome data to select and evaluate the suitability of ten candidate RGs, including Actin (Actin), polyubiquitin (UBQ), glyceraldehyde-3-phosphate dehydrogenase (GAPDH), elongation factor 1-α (EF1α), β-tubulin (β-TUB), α-tubulin (α-TUB), 60S ribosomal protein L13-1 (RPL13AD), aquaporin PIP1-2 (PIP1-2), Intima protein (ALB3) and Cyclin (CYCB1-2) for normalizing leaf color-related genes’ expression levels via qRT-PCR. Stability rankings analysis via common software Best-Keeper, GeNorm, and NormFinder disclosed that both ten genes met the requirements of RGs. Of them, EF1α exhibited the highest stability and was selected as the most reliable. The reliability and accuracy of EF1α were confirmed through qRT-PCR analysis of fifteen chlorophyll pathway-related genes. The expression patterns of these genes via EF1α normalization were consistent with the results by RNA-Seq. Our results will pave the way for molecular dissection of leaf color mutations in D. officinale.

Using nanoindentation under various strain rates, the mechanical properties of a selective laser melted (SLM) SKD61 at the 800 mm/s scan speed was investigated and compared to SLM H13. No obvious pile-up due to the ratio of the residual depth (h_f) and the maximum depth (h_max) being lower than 0.7 and no cracking were observed on any of the indenter surfaces. The nanoindentation strain-rate sensitivity (m) of SLM SKD61 was found to be 0.034, with hardness increasing from 8.65 GPa to 9.93 GPa as the strain rate increased between 0.002 s⁻¹ and 0.1 s⁻¹. At the same scan speed, the m value of SLM H13 (m = 0.028) was lower than that of SLM SKD61, indicating that the mechanical behavior of SLM SKD61 was more critically affected by the strain rate compared to SLM H13. SLM processing for SKD61therefore shows higher potential for advanced tool design than for H13.

Effective and rapid mixing is essential for various chemical and biological assays. The present work reports a simple and low-cost micromixer based on magnetofluidic actuation. The device takes advantage of magnetoconvective secondary flow, a bulk flow induced by an external magnetic field, for mixing. A paramagnetic stream of diluted ferrofluid and a non-magnetic stream are introduced to a straight microchannel. A permanent magnet placed next to the microchannel induced a non-uniform magnetic field. The magnetic field gradient and the mismatch in magnetic susceptibility between the two streams create a body force, which leads to rapid and efficient mixing. The micromixer reported here could achieve a high throughput and a high mixing efficiency of 90 % in a relatively short microchannel.

In industry 4.0 era, video applications such as surveillance visual systems, video conferencing, or video broadcasting have been playing a vital role. In these applications, for manipulating and tracking objects in decoded video, the quality of decoded video should be consistent because it largely affects to the performance of the machine analysis. To cope with this problem, we propose a novel perceptual video coding (PVC) solution in which a full reference quality metric named Video Multimethod Assessment Fusion (VMAF) is employed together with a deep convolutional neural network (CNN) to obtain the consistent quality while still achieving the high compression performance. First of all, to achieve the consistent quality requirement, we propose a CNN model with an expected VMAF as input to adaptively adjust the quantization parameters (QP) for each coding block. Afterwards, to increase the compression performance, a Lagrange coefficient of Rate-Distortion optimization (RDO) mechanism is adaptively computed under Rate-QP and Quality-QP models. Experimental results show that the proposed PVC has achieved two targets simultaneously: the quality of video sequence is kept consistently with an expected quality level and the bit rate saving of the proposed method is higher than traditional video coding standards and relevant benchmark, notably with around 10% bitrate saving in average.

We consider the Dirac field in polar formulation, showing that when torsion is taken in effective approximation the theory has the thermodynamic properties of a van der Waals gas, that when the limit of zero chiral angle is taken the theory reduces to that of a Weyssenhoff fluid, and that under the spinless condition it gives the Newtonian particle. This nesting of approximations will allow us to interpret the various objects pertaining to the spinor, with torsion providing a form of negative pressure, and the chiral angle being related to a type of internal dynamics.

The effect of atomic and molecular microfied dynamics on spectral line shapes is under consideration. This problem is treated in the framework of the Frequency Fluctuation Model (FFM). For the first time the FFM is tested for the broadening of a spectral line by neutral particles. The usage of the FFM allows one to derive simple analytical expressions and perform fast calculations of the intensity profile. The obtained results was compared with Chen and Takeo theory (CT), which is in a good agreement with experimental data. It was demonstrated that for moderate values of temperature and density the FFM successfully describes the effect of the microfield dynamics on a spectral line shape.

The Kwee van Woerden (KvW) method for the determination of eclipse minimum times has been a staple in eclipsing binary research for decades, due its simplicity and independence of external input parameters. However, its estimates of the timing error have been known to be of low reliability. During the analysis of very precise photometry of CM Draconis eclipses from TESS space mission data, KvW’s original equation for the timing error estimate produced numerical errors, which evidenced a fundamental problem in this equation. This contribution introduces an improved way to calculate the timing error with the KvW method. A code that implements this improved method, together with several further updates over the original method is presented as well. An example application on the CM Draconis light curves from TESS is given, where we show that its timing error estimates of about 1 second are in excellent agreement with error estimates obtained by other means.

Vietnam is the second largest coffee producer in the world, mostly from the Central Highlands region where water has been becoming a scarce resource. Since 2014, drought has been strongly affecting Central Highlands’ agriculture, particularly coffee production. The drought leads to changes in flowering, ripening and thus harvesting times of coffee. Coffee productivity has reduced about 50 percent. Ultimately, coffee quantity and quality is jeopardized which endangers coffee farmers who occupy 90 per cent of population and their livelihoods mainly rely on coffee. Most of coffee farmers have had to develop alternative strategies to respond to the drought. Based on quantitative and qualitative data collected from 50 coffee households in a community in the Central Highlands, this research has indicated that farmers had to find the ways to adapt as well as to cope with drought. The ways of adaptation and coping were diverse, including short, medium and long-term plans. To strengthen the adaptation and coping strategies of farmers with drought in the short term, it is recommended that authorities provide more technical and financial support to farmers. Furthermore, longer term strategies need to focus on land use planning, investment in irrigation schemes, and consolidated afforestation schemes in appropriate areas.

This paper introduces the complex Rayleigh-van der Pol-Duffing oscillators (RVDOs), which are hyperchaotic and can be either autonomous or non-autonomous. The fundamental dynamics of the autonomous and nonautonomous complex RVDOs including dissipation, symmetry, fixed points and their stability are studied. These oscillators are found in various important fields of physics and engineering. The paper proposes a scheme to achieve phase synchronization (PS) and antiphase synchronization (APS) for different dimensional models. These kinds of synchronization are considered as generalization of several other types of synchronization. For this scheme we use the active control method based on Lyapunov stability theory. By analytically determining the control functions, the scheme achieved PS and APS. Our scheme is applied to study PS of hyperchaotic behaviours for two distinct hyperchaotic non-autonomous and autonomous complex RVDOs. Additionally, the scheme is employed to achieve APS of chaotic real non-autonomous RVDO and hyperchaotic complex autonomous RVDO, including those with different dimensions. Our work presents numerical results that plot the amplitudes and phases of these hyperchaotic behaviours, demonstrating the successful achievement of PS and APS.

VNREDSat-1 is the first Vietnamese satellite allowing the survey of environmental parameters such as vegetation and water coverages, or surface water quality at medium spatial resolution (from 2.5 to 10 meters depending on the considered channel). The NAOMI sensor on board VNREDSat-1 has the required spectral bands to assess the suspended particulate matter concentration, SPM. Because recent studies have shown that the remote sensing reflectance, Rrs(), at the blue (450 – 520 nm), green (530 – 600 nm), and red (620 – 690 nm) spectral bands can be assessed from NAOMI with a good accuracy, the present study is dedicated to the development and validation of an algorithm (hereafter referred to as V1SPM) to assess SPM from Rrs() over inland and coastal waters of Vietnam. For that purpose, an in situ data set of hyper-spectral Rrs() and SPM (from 0.47 to 240.14 g.m-3) measurements collected at 205 coastal and inland stations has been gathered. Among the different approaches, including 4 historical algorithms, the polynomial algorithms involving the red-to-green reflectance ratio presents the best performance on the validation data set (MAPD of 18,7%). Compared to the use of a single spectral band, the band ratio allows to reduce the scatter around the polynomial fit as well as the impact of imperfect atmospheric corrections. Due to the lack of matchup data points with VNREDSat-1, the full VNREDSat-1 processing chain (RED-NIR and V1SPM) aiming at estimate SPM from the top-of-atmosphere signal has been applied to the Landsat-8/OLI match-up data points with relatively low to moderate SPM concentration (3.33-15.25 g.m-3) showing a MAPD of 15,8%. An illustration of the use of this VNREDSat-1 processing chain during a flooding event occurring in Vietnam is provided.

The paper presents the prediction of hydrodynamic characteristics of different rudder -plane configurations behind a submarine in deep water through the Reynolds-Averaged Navier-Stokes method in Ansys Fluent Solver. The hydrodynamic force and moment acting on the Cross-plane, X-plane, and Y-plane rudder configurations are analyzed for estimating hydrodynamic coefficientsfor predicting the advantages of each configuration to control the ship. The obtained results show that X-force of the X-plane rudder configuration is larger than the force acting on the Cross-plane rudder and Y-plane rudder configurations. However, Y-force, and Z-force of the X-plane rudder configuration are significantly greater than the Y-force of the left configurations. The same tendency can be seen in the moment of the X-plane rudder about the y-axis and z-axis. The roll moment induced by the Y-plane and Cross-plane rudder configurations is significantly larger than the case of the X-plane rudder configuration.

Study Objectives: To (1) investigate the prevalence of sleep disorder symptoms in caregivers of children with autism spectrum disorder (ASD) and (2) the relationships between caregiver sleep problems and their health-related quality of life and family quality of life. Methods: Descriptive cross-sectional study of caregivers (N=62) of children ages 6 to 11 years old diagnosed with ASD receiving care at a regional autism research and resource center. Measurements and Results: Participants completed the Sleep Habits Questionnaire (SHQ), the Medical Outcomes Study (MOS) SF-12, and the Beach Center Family Quality of Life Scale (FQOL). Caregivers with longer sleep duration reported better mental health and better family quality of life. Caregivers who reported insomnia symptoms, non-restorative sleep, and insufficient sleep were more likely to report poorer mental health than caregivers who did not report these sleep disorder symptoms. Caregivers with obstructive sleep apnea and restless legs syndrome experienced worse physical quality of life. Conclusions: The physical and mental health of the primary caregiver is essential to the support of the child with ASD and to the functioning of the family. The study findings point to the importance of future research and interventions to enhance sleep health in order to improve quality of life for caregivers of children with ASD.

Presenting a case report about a 14-year-old female patient presenting with a history of weakness in all four limbs since the age of 5. The patient has a history of difficulty in walking, wearing footwear, climbing stairs, and performing fine motor tasks. During the neurological examination showed mild spasticity, muscle weakness, areflexia, ill-sustained clonus, and sensory deficits. Radiological examination, including a contrast-enhanced MRI of the brain was done which showed findings that are consistent with Megalencephalic leukoencephalopathy with subcortical cysts, also known as Van der Knaap disease.

JIS SUJ2 is most widely used in bearing steels. The advantages are good hardenability, excellent fatigue, wear resistance and comprehensive mechanical properties. For wear resistance and fatigue resistance of the steel are getting more and more attention, the residual stress state and its distribution on the surface of the heat affect zone are critical factors affecting the fatigue life and wear resistance of the parts. In this study, using the SUJ2 as the material to talk about the surface residual stress and retained austenite distribution. Doing the quenching and tempering treatment to obtain different microstructures, using the induction method to re-quench the case region. After the heat treatment, measuring the residual stress and retained austenite volume on the surface by X-ray diffraction, observing the microstructure and comparing the hardness. The results show that the microstructure after heat treatment contains unsolidified carbides, tempered martensite and retained austenite. The residual stress on the surface is the tensile state. In the re-hardened area after induction quenching, the residual stress is all compressive, and the values are more than -800 MPa. In conclusion, in the same output power condition can be observed that the microstructure of the specimens before induction hardening has a significant impact on the effective case depth. The surface residual stress has changed from a tensile to a compressive state. In the re-hardened area, the maximum of the residual compressive stress increased with the austenitized temperature increase.

In the overall context of national eco-conservation civilization development and considering the hills in the Beijing-Tianjin-Hebei-Shanxi region, the local forest coverage rate is gradually on the rise, and so is the risk of forest fire. Every year, satellites can monitor and detect hundreds of fire spots on average. In recent years, serious fire took place for several times, leading to loss of life and personal injury. Then the fire-fighting work consumed huge amount of labor and material resources, exerting negative social impacts in many ways. Thus, the analysis of fire climate background in this region and the forecast based on fire weather indexes constitute an important part in the forest fire risk management. Located in the tropical monsoon climate zone, four provinces and municipalities of Beijing, Tianjin, Hebei and Shanxi are similar in terms of climate characteristics. This study tries to analyze the characteristics about fire spots under satellite monitoring, fire climate and fire weather index. The probability distribution analysis of weather index about fire spots in history and key meteorological observation stations as well as the weather index analysis in the early stage of typical fire indicate that the Fine Fuel Moisture Content (FFMC) and the Initial Spread Index (ISI) in the Fire Weather Index (FWI) system is applicable to the fire risk analysis in the Beijing-Tianjin-Hebei-Shanxi region, which can also effectively indicate the fuel moisture and spread conditions. As regards to the average level in Beijing-Tianjin-Hebei-Shanxi, when the FFMC is smaller than 93.5 and the ISI is also smaller than 5.0, there is a low risk of fire; when the FFMC is above 94 and the ISI is larger than 10.0, there is a high risk of fire; and the fire risk will be extremely high if the FFMC is over 96 and the ISI is above 13.0. In the practical fire-fighting management, the fire danger class can be released in reference to the ISI classes and threshold values of key meteorological observation stations under analysis provided by this study.

The biomimetic design of engineering structures is based on biological structures with excellent mechanical properties, which are the result of billions of years of evolution. However, current biomimetic structures, such as ordered lattice materials, are still inferior to many biological materials in terms of structural complexity and mechanical properties. For example, the structure of \textit{Euplectella aspergillum}, a type of deep-sea glass sponge, is an eye-catching source of inspiration for biomimetic design; however, guided by scientific theory, how to engineer structures surpassing the mechanical properties of \textit{E. aspergillum} remains an unsolved problem. The lattice structure of the skeleton of \textit{E. aspergillum} consists of vertically, horizontally, and diagonally oriented struts, which provide superior strength and flexural resistance compared with the conventional square lattice structure. Herein, the structure of \textit{E. aspergillum} was investigated in detail, and by using the theory of elasticity, a lattice structure inspired by the bionic structure was proposed. The mechanical properties of the sponge-inspired lattice structure surpassed the sponge structure under a variety of loading conditions, and the excellent performance of this configuration was verified experimentally. The proposed lattice structure can greatly improve the mechanical properties of engineering structures, and it improves strength without much redundancy of material. This study achieved the first surpassing of the mechanical properties of an existing sponge-mimicking design. This design can be applied to lattice structures, truss systems, and metamaterial cells.

Livestock farming is a major source of greenhouse gas and ammonia emissions. In this study, we estimate methane, nitrous oxide and ammonia emission from livestock sector in the Red River Delta region from 2000 to 2015 and projection to 2030 using IPCC 2006 methodologies with the integration of local emission factors and provincial statistic livestock database. Methane, nitrous oxide and ammonia emissions in 2030 are estimated at 132 kt, 8.3 kt and 34.2 kt, respectively. Total global warming potential is 9.7 MtCO_2eq in 2030, accounts for 33% greenhouse gas emissions from livestock in Vietnam. Pig farming is responsible for half of both greenhouse gases and ammonia emissions in the studied region. Other major livestock for greenhouse gas emission is cattle and for ammonia emission is poultry. Hanoi contributes for the largest emissions in the region in 2015 but will be caught up and surpassed by other provinces in 2030.

The COVID-19 pandemic and associated restrictive measures implemented may considerably affect people’s lives. This study aimed to assess the well-being of Vietnamese people after COVID-19 lockdown measures were lifted and life gradually returned to normal. An online survey was organized from 21st to 25th April 2020 among Vietnamese residents aged 18 and over. Besides collecting socio-demographic and COVID-19-related data, the WHO-5 Well-Being Index (scored 0–25) was used to score participants’ well-being. A multivariate logistic regression model was used to determine the predictors of well-being. A total of 1922 responses were analyzed (mean age: 31 years; 30.5% male). Mean well-being score was 17.35±4.97. Determinants of high well-being score (≥13) included older age, eating healthy food, practising physical exercise, working from home, and adhering to the COVID-19 preventive measures. Female participants, persons worried about their relatives’ health, and smokers were more likely to have a low well-being score. In conclusion, after the lockdown measures were lifted, the Vietnamese people continued to follow COVID-19 preventive measures and most of them scored high on the well-being scale. Waiting to achieve large scale COVID-19 vaccine coverage, promoting preventive COVID-19 measures remains important, together with strategies to guarantee the well-being of the Vietnamese people.

A new algorithm is developed in this study to automatically detect reinforced concrete structures' rebar locations and diameters using the ground penetrating radar technique. The method approximates the hyperbolic signatures using two-way travel time and bi-quadratic equations. The study includes formulating electromagnetic wave speed in reinforced concrete (RC) structures. The algorithm was used in a computer code to provide an automated analysis of ground-penetrating radar data collected from a pre-planned survey grid. Two RC slabs were fabricated and tested to validate the proposed method. The proposed method is efficient in signal processing and accurately and reliably determining the rebar information.

In this work, silver nanoparticles (AgNPs) were synthesized rapidly and eco-friendlily using the extract of Mulberry leaves and aqueous solution of silver nitrate without any toxic chemical [1,2]. The Mulberry leaves extract acts as both reducing agent and stabilizing agent. The UV-Vis spectrum shows peak at 430 nm. The TEM image of synthesized AgNPs sample shows spherical shaped particles whose size range from 15 to 20 nm. TEM image of nano silver solution sample synthesized by microwave assisted method shows nearly spherical particles with an average particle size of 10 nm. The absorption UV-vis spectrum of silver nanoparticles synthesized by microwave assisted method (AgNPsmw) shows a sharp absorption band around 415 nm. After two month storage of AgNPsmw, the absorption spectrum of AgNPsmw was taken again. The UV-Vis spectrum shows negligible peak changes of silver nanoparticles have occurred after two months of storage. The synthesized AgNPs material could be used as an antimicrobial, used in the field of textile and in wastewater treatment.

Butyl rubber-based composite (BRC) is one of the most popular materials for the fabrication of protective glove against chemical and mechanical risks. However, in many working places such as metal manufacturing or automotive mechanical services, its mechanical hazards usually appear together with metalworking fluids (MWFs). The presence of these contaminants, particularly at high temperature, could modify its properties due to the scission, the plasticization, the crosslinking of polymer network and thus led to severe modification of mechanical and physicochemical properties of material. This work aims to determine the effect of temperature and a metalworking fluid on mechanical behavior of butyl rubber composite dealing with crosslinking density, cohesion forces and elastic constant of BRC on the based on Mooney-Rivlin’s theory. The effect of temperature with and without MWFs on thermo dynamical properties and morphology of butyl membranes is also investigated. The prediction of service lifetime is then evaluated from extrapolation of Arrhenius plot at different temperatures.

In the field of computer vision, large-scale image classification tasks are both important and highly challenging. With the ongoing advances in deep learning and optical character recognition (OCR) technologies, neural networks designed to perform large-scale classification play an essential role in facilitating OCR systems. In this study, we developed an automatic OCR system designed to identify up to 13,070 large-scale printed Chinese characters by using deep learning neural networks and fine-tuning techniques. The proposed framework comprises four components, including training dataset synthesis and background simulation, image preprocessing and data augmentation, the process of training the model, and transfer learning. The training data synthesis procedure is composed of a character font generation step and a background simulation process. Three background models are proposed to simulate the factors of the background noise and anti-counterfeiting patterns on ID cards. To expand the diversity of the synthesized training dataset, rotation and zooming data augmentation are applied. A massive dataset comprising more than 19.6 million images was thus created to accommodate the variations in the input images and improve the learning capacity of the CNN model. Subsequently, we modified the GoogLeNet neural architecture by replacing the FC layer with a global average pooling layer to avoid overfitting caused by a massive amount of training data. Consequently, the number of model parameters was reduced. Finally, we employed the transfer learning technique to further refine the CNN model using a small number of real data samples. Experimental results show that the overall recognition performance of the proposed approach is significantly better than that of prior methods and thus demonstrate the effectiveness of proposed framework, which exhibited a recognition accuracy as high as 99.39% on the constructed real ID card dataset.

The signature of chaotic systems can be characterized either by the sensitivity of the initial conditions or by the change of its parameters. This feature can be used for manufacturing high sensitivity sensors. Sensors based on chaotic circuits have already been used for measuring water salinity, inductive effects, and both noise and weak signals. This article investigates an impedance sensor based on the Van der Pol and Duffing damped oscillators. The calibration process is a key point and therefore the folding behavior of signal periods was also explored. A sensitivity of 0.15 kΩ/Period was estimated over a range from 89.5 to 91.6 kΩ. This range can be adjusted according to the application by varying the gain of the operational amplifier used in this implementation. The development of this type of sensor might be used in medical and biological engineering for skin impedance measurements, for example. This type of chaotic sensor has the advantage of sensing small disturbances and then detect small impedance changes within biological materials which, in turn, may not be possible with other detectors.

The use of sensors in monitoring of lateral accelerations in delivery van transport focuses on measuring lateral accelerations on routes with roundabouts and curves to increase road safety. Using microelectromechanical system (MEMS) sensors, it measures the lateral accelerations acting on the vehicle and the load being transported during the test drives to study vehicle dynamics for cargo securing. Using an accelerometer and position tracking, accelerations can be detected when traversing curves and roundabouts at selected locations on the vehicle. The level of accelerations on the roof of the vehicle was found to be like those occurring on a lashed load with limited movements, where regression analysis can be used to determine the relationship between lateral accelerations at different sensor positions. If we compare the mean values of the lateral accelerations of the individual events between the sensors, the sensor on the side of the vehicle body at the height of the sensor on the load had approximately 5% lower mean values than the sensor on the roof. The sensor on the load measured approximately 5% higher mean values than the sensor on the roof. Hence, the mean lateral accelerations of the individual events for the sensor on the load are 10% higher than for the sensor at the same height on the vehicle body. From the above testing, we can say that the values of the mean lateral accelerations of the van from the sensor on the roof of the vehicle, are closer to the values of the accelerations of the sensor on the load than to the values of the sensor on the body of the vehicle at the same height.