Poly (Lactic Acid) (PLA) / Ground Tire Rubber (GTR) blends using Dicumyl peroxide (DCP) as a crosslinking agent were prepared as a route to recycle wastes rubber from the automotive industry. The GTR were exposed to grinding and exhibited mechanical damage, traduced at the rubber network scale by chains scission and/or chemical cross-links breakage. Such damage is accompanied by a decrease of 80% of the rubber chains network density of the initial tire buffing but found independent on the type of grinding (cryogenic, dry ambient) or on the GTR size (from <400 µm to <63 µm). Moreover, the finest sieved GTR contain the largest the amount of reinforcing elements (carbon black, clay) that can be advantageously used in PLA/GTR blends. The melt-blending of these finest GTR particles obtained by cryo-grinding at an amount of 15 wt.% and in presence of the crosslinking agent (DCP), resulted in an optimum improvement of the ductility, energy at break and impact strength of the PLA/GTR blends as compared to neat PLA, while maintaining its stiffness. The results were attributed to (i) the good dispersion of the fine GTR particles into the PLA matrix, (ii) the partial re-crosslinking of the GTR particles and co-crosslinking at PLA/GTR interface and (iii) the presence of reinforcing carbon black into the GTR particles and clay particles dispersed into the PLA matrix.

The effect of the strain rate on damage in carbon black filled EPDM stretched during single and multiple uniaxial loading is investigated. This has been performed by analysing the stress-strain response, the evolution of damage by Digital Image Correlation (DIC), the associated dissipative heat source by InfraRed thermography (IR), and the chains network damage by swelling. The strain rates were selected to cover the transition from quasi-static to medium strain rate conditions. In single loading conditions, the increase of the strain rate yields in a preferential damage of the filler network while rubber network is preserved. Such damage is accompanied by a stress softening and an adiabatic heat source rise. Conversely, increasing the strain rate in cyclic loading conditions yields in a filler network accommodation and a high self-heating whose combined effect is proposed as a possible cause of the ability of filled EPDM to limit damage, by reducing cavities opening during loading and favoring cavities closing upon unloading.

In the 21st century, museums have come to realize that the human skeletons they display might have problematic origins. The older anthropological skeletal collections typically originate from anatomical dissection of the executed and the very poor, or from scavenged graves of indigenous people. Such collections are currently being re-evaluated in many countries, and reburying or repatriating museum skeletons have become viable options. A particularly difficult question is what to do with human remains of unknown origins. Here, we present and discuss one such case, where a human skeleton of unclear origin in the 1930’s was brought to a local museum in Bollnäs, Sweden, under likely unethical circumstances. Most of the bones have now been lost, except for the skull, the sacrum and one lumbar vertebra, which in 2007 were transferred to the Museum of Ethnography in Stockholm. The skull was there put on display as the “Bollnäs skull”, and was presented to the public to illustrate the dilemmas involved in handling human remains in the post-colonial era. The original gift letter from 1934 stated that the skeleton came from San Nicolas Island outside the California coast, but this letter contained numerous instances of incorrect information and was therefore deemed not trustworthy. However, our critical examination of the skull and its background information indicates that San Nicolas Island is a plausible origin, and we suggest that a bioarchaeological comparison should be made between the skull and living descendants of the San Nicolas Island population, and/or with archaeological human skeletons excavated from the island.

Background: This study examines the relationship between energy usage, health issues, and pro-environmental behavior (PEB) in Kyrgyzstan, amidst the country's commitment to transition from coal-based energy to renewable sources in line with the Paris Agreement. The purpose is to investigate citizens' attitudes towards PEB and their intentions to engage in environmentally friendly actions, focusing on gas, electricity, and coal. Methods: Drawing upon the Theory of Planned Behavior (TPB) framework, a survey was conducted among 1,455 respondents to explore attitudes towards PEB and energy sources' impact on health issues. Results: Decarbonization efforts in Kyrgyzstan and Central Asia are in their early stages, with coal remaining a primary energy source. The study emphasizes the importance of governmental policies and citizen action in achieving decarbonization goals. Rising electricity costs outweigh the increase in indirect energy costs for food, posing challenges for households in adapting to changing energy dynamics. Conclusions: Targeted interventions and communication strategies are crucial to promote pro-environmental behavior and facilitate the transition to sustainable energy sources. Understanding the relationships between health concerns, air pollution awareness, PEB, and energy source choices can inform policymakers and organizations in their efforts to ensure a sustainable and healthy future for Kyrgyzstan and other Central Asian countries.

RNA-seq faces persistent challenges due to the ongoing expanding array of data processing workflows, none of which have yet achieved standardization to date. It is imperative to determine which method most effectively preserves biological facts. Shannon entropy serves as a tool for depicting the biological status of a system. Thus, we assessed the measurement of Shannon entropy by several RNA-seq workflow approaches, employing RPKM and median normalization on paired samples of 475 TCGA RNA-seq datasets spanning eight different cancer types with 5-year overall survival rates ranging from 30% to 98%. Our analysis revealed that the RPKM normalization coupled with a threshold of log2 fold change ≥1 for indentifying differentially expressed genes, yielded the best results with a correlation coefficient of 0.91. We propose that Shannon entropy can serve as an objective metric for refining the optimization of RNA-seq workflows.

The classical human satellite DNAs, also referred to as human satellites 1, 2 and 3 (HSat1, HSat2, HSat3, collectively HSat1-3) constitute the largest individual arrays of tandemly repeated DNA sequences in the genome. Even though they were among the first human DNA sequences to be isolated and characterized at the dawn of molecular biology, HSat1-3 have been left behind in the genomics era and remain among the most enigmatic sequences in the human genome. Although HSat1-3 total roughly 3% of the genome on average, they were almost entirely missing from the human genome reference assembly for 20 years. Recently, the Telomere-to-Telomere Consortium produced the first truly complete assembly of a human genome, including the enormous HSat1-3 arrays, opening them up for a new wave of discovery. Towards this end, here, I provide an account of the history and current understanding of HSat1-3 genomics, evolution, and roles in disease.

Môle Saint-Nicolas, like all other communes in the Republic of Haiti, faces increasing climate variability, impacting agricultural production and water resources. Consequently, there is a pressing need for adaptation to these climatic changes. This research aims to showcase the adaptation strategies deployed by farmers to cope with the increasing climate variability. Surveys were conducted through group and individual discussions with a randomly selected cohort of 150 farmers. Two types of analysis were performed: quantitative and qualitative. The quantitative data analysis was conducted using SPSS software. The findings reveal that farmers have perceived changes in rainfall patterns, temperature, wind, and their environment. These changes manifest as irregular rainfall, higher temperatures, prolonged drought periods, violent winds accompanied by rain, premature cessation of rains, and reduced flow from water sources. In response, the most common adaptation strategies developed include selecting new cultivars, early-maturing varieties, crop rotation and diversification, canal dredging, new soil preparation methods, upstream water source protection, and micro-watershed management. The significance of this research lies in its contribution to enhancing farmers' adaptive capacities by alerting stakeholders in the irrigated perimeters about the consequences of climate change, thereby incorporating the real needs of farmers in future projects.

Indigo leaves form various plant species are sources of dyes/pigments, not fully exploited for making sustainable textiles. Blue indigo vat dye extracted from indigo leaves, yields high wash colorfastness but fades slowly with light, and is not easily used for direct printing. Indigo leaves can be used to produce textiles of various color shades, while light resistant Mayan-inspired hybrid pigments have not yet been used for textile coloring. Using blue indigo dyes from 3 plant species, with exhaustion dyeing, intense wash resistant blue colored textiles are produced, and in the case of Indigofera Persicaria tinctoria, textiles have antibacterial activity against S. Epidermis and E. Coli.100% Natural Mayan-inspired blue indigo pigment, made from Sepiolite clay and indigo dye, was used both in powdered and paste forms to perform pigment textile dyeing by pad cure process, and direct screen printing on textiles. A water-based bio-binder (40%) was used efficiently for both padding and printing. Bio-based Na Alginate thickener allowed color fast printing on both polyester and cotton fabrics, while bio-based glycerin allowed good print color fastness on polyester only, yielding prints with excellent color fastness to wash (5/5), to dry and wet rubbing (5/5) and light (7/7).

Body weight support (BWS) and incline running (IR) are commonly used either during rehabilitation or during training separately, with many positive effects on athletes’ performance and rehabilitation. The aim of this study is to investigate the effect of BWS and IR. In eighteen healthy men (age: 20.3 ± 1.2 yr, body weight: 70.2 ± 4.8 kg, body height: 179.6 ± 5.4 cm), the changes in electromyographic activity (EMGA) during a 10-min run with BWS (15% or 30% of body weight; in different occasions) and IR at 7%, as well as jumping performance and gait spatiotemporal parameters were evaluated. Lower Rating of Perceived Exertion and a significant decrease in VL (33,4%), SOL (17%), and GL EMGA (28.5%, p &lt; 0.05) but not in GM (10.5%, p &gt; 0.05), were observed during BWS30% at 7% slope compared to flat running. Also, low-frequency fatigue of the quadriceps was induced only after running without BWS at 7% slope (P = 0.011). No changes were found in jumping performance (p = 0.246) and gait spatiotemporal parameters (p &gt; 0.05) except for flight time (p &lt; 0.006). In conclusion, compared to normal flat running, BWS reduces electromyographic activity and fatigue during slope running.

Chronic inflammation may have a detrimental impact on human health as it tends to result in cancer. In addition, it is often linked to different steps that participate in tumorigenesis, including cellular transformation, survival, promotion, invasion, proliferation, angiogenesis, and metastasis. Hence, inflammation predisposes cancer development and plays a vital role in promoting all tumorigenesis stages. Inflammation is caused by many factors, such as bacterial and viral infections, tobacco smoking, autoimmune diseases, obesity, asbestos exposure, and many others, increasing cancer risk. Moreover, cancer can be enhanced by mutations that proceed to cancer progression. Consequently, it leads to immunosuppression and provides a favorable background for tumor development. Although many studies address the question of relationships between inflammation and cancer development, little attention is paid to the link between inflammation and blood cancer. Therefore, the current study reviews the role of inflammation in cancer development, particularly in blood cancer. A meta-analysis research approach meets the research objective and answers the research question. The review results indicate that chronic inflammation directly relates to the development of many cancer types, blood cancer in particular.

Carbohydrate and menthol mouth-swilling have been used to enhance exercise performance in the heat. However, these strategies differ in mechanism and subjective experience. Participants (n=12) sat for 60 min in hot conditions (35°C; 15±2%), following a 15 min control period, participants undertook three 15 min testing blocks. A randomised swill (Carbohydrate; Menthol; Water) was administered per testing block (one swill every three minutes within each block). Heart rate, tympanic temperature, thermal comfort, thermal sensation and thirst were recorded every three minutes. Data were analysed by ANOVA, with carbohydrate intake controlled for via ANCOVA. Small elevations in heart rate were observed after carbohydrate (ES: 0.22 ± 90% CI: -0.09 to 0.52) and water swilling (0.26; -0.04 to 0.54). Menthol showed small improvements in thermal comfort relative to carbohydrate (-0.33; -0.63 to 0.03) and water (-0.40; -0.70 to -0.10), and induced moderate reductions in thermal sensation (-0.71; -1.01 to -0.40 and -0.66; -0.97 to -0.35, respectively). Menthol reduced thirst by a small to moderate extent. These effects persisted when controlling for dietary carbohydrate intake. Carbohydrate and water may elevate heart rate, whereas menthol elicits small improvements in thermal comfort, moderately improves thermal sensation and may mitigate thirst; these effects persist when dietary carbohydrate intake is controlled for.

Background: The uptake of COVID-19 booster vaccines has been significantly low. Therefore, it is questionable whether combining the COVID-19 booster vaccines with Influenza vaccines can increase the population's interest in taking such vaccines and manage the health pandemic effectively. Methodology: In this systematic review and meta-analysis, a synthesis of the findings and summary of a total of 30 research articles based on the topic, ‘combining influenza and COVID-19 booster vaccination strategy’ was undertaken. The research articles were identified from three databases, namely, PubMed, Cochran Library, and Google Scholar using specific keywords and inclusion criteria. However, research articles that were not peer-reviewed and not published in English were excluded from the systematic review and meta-analysis. The average risk ratio of the included articles was 0.78% based on a 95% CI. On the other hand, the heterogeneity between such studies was I² = 35%, while the statistical significance of their findings occurred at p < 0.05. The average p-value of the included research studies was p = 0.62, implying that the null hypothesis was not rejected in almost all the studies. Results: A synthesis of the chosen research articles revealed that when influenza and COVID-19 booster vaccines are combined, there is potential for an increase in the uptake of the latter, mainly because many populations have already been accustomed to taking influenza vaccines on an annual basis. Conclusions: In this way, through such findings, medical health experts can make informed decisions to increase the population's willingness to receive the COVID-19 booster vaccines.

Background of the Study: We investigated the link between hypertension and cancer since it has been suggested that hypertension may raise the long-term risk of cancer. Previous large observational cohort studies found that greater blood pressure (BP) was related to a higher risk of cancer. Mendelian randomization (MR) was utilized to produce less confounded blood pressure estimates (BP) on overall and site-specific malignancies. The study aims to draw conclusions on the relationship between high blood pressure and cancer. Methods: Studies on high blood pressure and various malignancies are inconclusive, except for renal cell carcinoma. However, given that most meta-analyses only contained a limited number of trials, some relative risks had small to moderate magnitudes, and several may have been impacted by residual confounding, careful interpretation is necessary. The study was conducted using the meta-analysis technique. Cochran's Q test and I2 test were used to assess statistical heterogeneity between studies in the current investigation for research involving two or more cause and outcome combinations. Results: Positive correlations were also reported between high blood pressure and esophageal adenocarcinoma, squamous cell carcinoma, liver, and squamous cell carcinoma. However, most studies lacked multivariable adjustments. Physical and numerical risk of cardiovascular disease is linked to bowel cancer but no other cancers. According to a meta-analysis, hypertensive persons could also be at increased danger of gastrointestinal and breast cancer. Most meta-analyses comprised several trials with moderate or mild hazard ratios.ConclusionDifferent types of cancers have been noted to be directly caused by hypertension. In addition, some treatments have also been associated with the side effects of cancer treatments to cause hypertension. Women facing hypertension have an increased risk of getting breast cancer. Although some cancers showed a real relationship with hypertension, others had no connection at all.

In winter 2008-2009, Lake Occhito, a strategic multiple-uses reservoir in South Italy, was affected by an extraordinary Planktothrix rubescens bloom. P. rubescens is a filamentous potentially toxic cyanobacterium which has recently colonized many environments in Europe. A number of studies is currently available on the use of remote sensing techniques to monitor different fresh water cyanobacteria species. By contrast no specific applications are available on the remote sensing monitoring of P. rubescens. In this paper we present a specific algorithm, based on Water Leaving Reflectances (WLR) from MERIS data, atmospherically corrected using the Aerosol Optical Thickness (AOT) retrieved by MODIS data, to detect P. rubescens blooms. The high accuracy in AOT data, provided by MOD09 surface reflectance product, at 1km spatial resolution, allowed obtaining a good correlation between the WLR and the P. rubescens chlorophyll-a concentrations measured in the field, through multiple stations fluorometric profiles. A modified Normalized Difference Chlorophyll index (NDCI) algorithm is presented. The performance of the proposed algorithm has been successfully compared with other specific algorithms for turbid productive waters. We demonstrated how important is to verify the spectral behaviour of bio-optical parameters in order to develop an ad hoc algorithm that better performs with respect to standard algorithms.

A significant number of research studies have focused on determining whether BMI influences various types of cancer. The findings of these studies showed that people have to manage their BMIs to decrease their risk of developing various types of cancer, one of which is ovarian cancer. A PRISMA guideline for systematic review and meta-analysis was used to identify 20 research studies related to the topic to establish the truth or falsity of the findings. Later, their findings were synthesized. The synthesis of the findings of such research articles suggests that overweight and obesity increase an individual’s risk of developing ovarian cancer and experiencing severe symptoms of the disease. In such a manner, the current research study can conclude that effective management of BMI is necessary for decreasing the prevalence and mortality rates associated with ovarian cancer.

We investigate the possible laboratory origins of the highly pathogenic avian influenza (HPAI) H5N1 clade 2.3.4.4b genotype B3.13, currently affecting various animal species and causing sporadic human infections. The first detection of HPAI H5N1 clade 2.3.4.4b in the Netherlands in 2020 raises concerns about earlier gain-of-function research. The proximal origins of HPAI H5N1 Clade 2.3.4.4b may be the USDA Southeast Poultry Research Laboratory (SEPRL) in Athens, Georgia and the Erasmus Medical Center in Rotterdam, the Netherlands. Genetic analysis indicates that genotype B3.13 emerged in 2024 and exhibits genetic links to genotype B1.2, which was identified to have originated in Georgia in January 2022 after the start of serial passage research with H5Nx clade 2.3.4.4 in mallard ducks at the USDA Southeast Poultry Research Laboratory (SEPRL) in Athens, Georgia in April 2021. Genotype B1.2 was found in a bottlenose dolphin (Tursiops truncatus) in March 2022 in Florida, indicating sudden new adaptations to different animal species. The NP gene of H5N1 clade 2.3.4.4b (genotype B3.13), which is causing outbreaks in cattle, was reported to have likely originated from an avian influenza A virus derived from mallard ducks. Significant mutations found in recent human cases, including PB2 E627K and PB2 M631L, also suggest links to serial passage experiments. However, further investigation is urgently needed to confirm these findings and to identify all H5N1 laboratory leaks that may have occurred with a focus on mallard ducks and other migratory waterfowl, which have the potential to infect a large number of poultry and livestock facilities around the world. A moratorium on gain-of-function research including serial passage of H5N1 is indicated to prevent a man-made influenza pandemic affecting animals and humans.

This study aimed to apply different complexity-based methods to surface electromyography (EMG) in order to detect neuromuscular changes after realistic warm-up and stretching procedures. Sixteen volunteers conducted two experimental sessions. They were tested before, after a standardized warm-up, and after a stretching exercise (static or neuromuscular nerve gliding technique). Tests included measurements of the knee flexion torque and EMG of biceps femoris (BF) and semitendinosus (ST) muscles. EMG was analyzed using the root mean square (RMS), sample entropy (SampEn), percentage of recurrence and determinism following a recurrence quantification analysis (%Rec and %Det) and a scaling parameter from a detrended fluctuation analysis. Torque was significantly greater after warm-up as compared to baseline and after stretching. RMS was not affected by the experimental procedure. In contrast, SampEn was significantly greater after warm-up and stretching as compared to baseline values. %Rec was not modified but %Det for BF muscle was significantly greater after stretching as compared to baseline. The a scaling parameter was significantly lower after warm-up as compared to baseline for ST muscle. From the present results, complexity-based methods applied to the EMG give additional information than linear-based methods. They appeared sensitive to detect EMG complexity increases following warm-up.

Various theoretical studies have shown that highly diluted plutonium solutions could have a positive temperature effect, but up to now, no experimental program has confirmed this effect. The French Plutonium Temperature Effect Experimental Program (or PU+ in short) aims to effectively show that such a positive temperature effect exists for diluted plutonium solutions. The PU+ experiments were conducted in the “Apparatus B” facility at the CEA VALDUC research center in France. It involved several sub-critical approach type experiments using plutonium nitrate solutions with concentrations of 14.3, 15, and 20 g/l at temperatures ranging from 20 to 40 °C. Fourteen (five at 20 g/l, four at 15 g/l, and five at 14.3 g/l) phase-I experiments (consisting in independent subcritical approaches) were performed between 2006 and 2007. The impact of the uncertainties on solution acidity and plutonium concentration made it difficult to demonstrate the positive temperature effect, requiring an additional phase-II experiment (with a unique plutonium solution) from 22 to 28 °C, that were performed in July 2007. This phase-II experiment has shown the existence of a positive temperature effect of ~ +2.2 pcm/°C (from 22 to 28 °C for a plutonium concentration of 14.3 g/l). It has been recently possible to confirm the results of this program with MORET 5 calculations by generating thermal scattering data S(α,β) at the correct experimental temperatures.

Off-grid electrification planning increasingly recognizes the importance of productive use of electricity (PUE) to promote community value creation and (financial) project sustainability. To ensure a sustainable and efficient integration in the community and energy system, PUE assets must carefully be evaluated to match both the community needs and the residential electricity demand patterns. We propose a novel methodology interlinking qualitative interviews, statistical analysis, and energy system modelling to optimize decision-making for PUE integration in off-grid energy systems in rural Madagascar by aligning relevant PUE effectively with anticipated residential electricity demand patterns based on socio-economic determinants of the community. We find that a possible contribution of the PUE to reducing the electricity costs depends signifi-cantly on three factors: 1. the residential electricity consumption patterns that are influenced by the socio-economic composition of the community, 2. the degree of flexibility of i) PUE assets and ii) operational preferences of the PUE user, and 3. the capacity of community members to finance and operate PUE assets. Our study demonstrates that significant cost reductions for PUE-integrated off-grid energy systems can be achieved by applying our proposed methodology. When matching PUE and residential consumption patterns, the integration of PUE assets in residential community energy system can reduce the financial risk of operators, provided the PUE enterprise operates reliably and sustainably. We highlight that the consideration of local value chains and co-creation approaches are essential to ensure the energy system is addressing the community’s needs, creates value for the community, enhances the project´s financial sustainability, and is achieving the overall objectives of decentralized energy system planning.

There exists a great potential for application in soil mechanics with the use of mechanistic models such as the finite element model, and other non-local models, such as the peridynamic model, since the soil mass can be modelled as a group of particles that interact with each other. In this work, we determine the bearing capacity of deep foundations where stresses are transmitted to deep deposits, which generally present better characteristics in terms of compressibility and shear strength. One of the main elements are driven piles, which must be previously designed, made and tested before their final use. In this work, a comparison with different methods is presented. The finite element method and the peridynamic model are used. Because the effect of consolidation was not taken into account, in these examples, the assumption is made that the structures are cemented in inert soil. Likewise, it is assumed that the water table has no influence on the simulations. Failure envelopes were observed where bonds between particles present high gradients of deformation and fracture. Bearing capacities were estimated and compared with those obtained from the Terzaghi and Meyerhof methods.

Traumatic cardiac arrest has a high mortality. We report the case of a 65 years old women who presented a cardiac arrest following traffic accident. Examinations concluded to a tension gastro thorax with a delayed diagnosis. Naso gastric tube insertion was for many authors a temporary care while waiting for surgery. We report on the diagnostic difficulties found in the literature and a recent review of published cases.

Manual review of the extensive literature covering nutrition-based lifestyle interventions to promote healthy cognitive ageing has proved educative, however, data-driven techniques can better account for the large size of the literature (tens of thousands of potentially relevant publications to date) and interdisciplinary nature of where relevant publications may be found. In this study we present a new way to map the literature landscape focusing on nutrition-based lifestyle interventions to promote healthy cognitive ageing. We applied a combination of citation network analysis and text mining to map out the existing literature on nutritional interventions and cognitive health. Results indicated five overarching clusters of publications, which could be further deconstructed into a total of 35 clusters. These could be broadly distinguished by focus on lifespan stages (e.g. infancy versus older age), and specificity regarding nutrition (e.g. narrow focus on iodine deficiency versus broad focus on weight gain). Rather than concentrating into a single cluster, interventions were present throughout the majority of the research. We conclude that a data-driven map of the nutritional intervention literature can benefit the design of future interventions, by highlighting topics and themes that could be synthesized across currently disconnected clusters of publications.

In proteomics, it is essential to quantify proteins in absolute terms if we wish compare results among studies and integrate high-throughput biological data into genome-scale metabolic models. While labeling target peptides with stable isotopes allows protein abundance to be accurately quantified, the utility of this technique is constrained by the low number of quantifiable proteins that it yields. Recently, label-free shotgun proteomics has become the “gold standard” for carrying out global assessments of biological samples containing thousands of proteins. However, this tool must be further improved if we wish to accurately quantify absolute levels of proteins. Here, we used different label-free quantification techniques to estimate absolute protein abundance in the model yeast Saccharomyces cerevisiae. More specifically, we evaluated the performance of seven different quantification methods, based either on spectral counting (SC) or extracted-ion chromatogram (XIC), which were applied to samples from five different proteome backgrounds. We also compared the accuracy and reproducibility of two strategies for transforming relative abundance into absolute abundance: a UPS2-based strategy and the total protein approach (TPA). This study mentions technical challenges related to UPS2 use and proposes ways of addressing them, including utilizing a smaller, more highly optimized amount of UPS2. Overall, three SC-based methods (PAI, SAF, and NSAF) yielded the best results because they struck a good balance between experimental performance and protein quantification.

3D printing is described as the third industrial revolution: its impact is global in industry and progresses every day in society. It presents a huge potential for ecology and evolution, sciences with a long tradition of inventing and creating objects for research, education and outreach. Its general principle as an additive manufacturing technique is relatively easy to understand: objects are created by adding material layers on top of each other. Although this may seem very straightforward on paper, it is much harder in the real world. Specific knowledge is indeed needed to successfully turn an idea into a real object, because of technical choices and limitations at each step of the implementation. This article aims at helping scientists to jump in the 3D printing revolution, by offering a hands-on guide to current 3D printing technology. We first give a brief overview of uses of 3D printing in ecology and evolution, then review the whole process of object creation, split into three steps: (1) obtaining the digital 3D model of the object of interest, (2) choosing the 3D printing technology and material best adapted to the requirements of its intended use, (3) pre- and post-processing the 3D object. We compare the main technologies available and their pros and cons according to the features and the use of the object to be printed. We give specific and key details in appendices, based on examples in ecology and evolution.

Academic and corporate research has been focusing on analyzing stock performances, financial markets, and investment strategies for decades. According to Lynch and Rothchild (1989), certain investments can be described as plays. In this work, the authors use the term for investments in value stocks, spin-offs, and turnarounds to analyze the long-term stock performance and risk-adjusted excess returns of up to five years for those stocks. Additionally, stocks with a supe-rior return performance are identified within an investment play based on low P/E and P/B mul-tiples. The study finds that value stocks, spin-offs, and turnarounds outperform the S&P 500 on average on a one-, three- and five-year investment horizon. The analysis of the three investment plays confirms earlier studies that investment plays constitute a profitable investment opportunity. Moreover, the research exemplifies that private investors could achieve an excess return (alpha) through a passive buy-and-hold investment strategy. Overall, the analysis provides a deeper in-sight into the long-term performance of value stocks, spin-offs, and turnarounds.

Molecule radiation can be used as a tool to study colder regions in switching arc plasmas like arc fringes in contact to walls and ranges around current zero (CZ). This is demonstrated in the present study for the first time for the case of ablation-dominated high–current arcs as key elements of self–blast circuit breakers. The arc in a model circuit breaker (MCB) in CO2 with and an arc in a long nozzle under ambient conditions with peak currents between 5 and 10 kA were studied by emission and absorption spectroscopy in the visible spectral range. The nozzle material was polytetrafluoroethylene (PTFE) in both cases. Imaging spectroscopy was carried out either with high-speed cameras or with intensified CCD cameras. A pulsed high-intensity Xe lamp was applied as background radiator for the broad-band absorption spectroscopy. Emission of Swan bands from carbon dimers was observed at the edge of nozzles only or across the whole nozzle radius with highest intensity in the arc center, depending on current and nozzle geometry. Furthermore, absorption of C2 Swan bands and CuF bands were found with the arc plasma serving as background radiator. After CZ, only CuF was detected in absorption experiments.

Large-scale crowd phenomena are complex to model because the behaviour of pedestrians needs to be described at both strategic, tactical, and operational levels and is impacted by the density of the crowd. Microscopic models manage to mimic the dynamics at low densities, whereas mesoscopic models achieve better performances in dense situations. This paper proposes and evaluates a novel agent-based architecture to enable agents to dynamically change their operational model based on local density. The ability to combine microscopic and mesoscopic models for multi-scale simulation is studied through a use case of pedestrians at the Festival of Lights, Lyon, France. Pedestrian outflow data is extracted from video recordings of exiting crowds at the festival. The hybrid model is calibrated and validated using a genetic algorithm that optimizes the match between simulated and observed outflow data. Additionally, a local sensitivity analysis is then conducted to identify the most sensitive parameters in the model. Finally, the performance of the hybrid model is compared to different models in terms of density map and computation time. The results demonstrate that the hybrid model has the capacity to effectively simulate pedestrians across varied density scenarios while optimizing computational performance compared to other models.

We present a case of a 47-year-old male who died unexpectedly from acute pulmonary hemorrhage 555 days after completing the BNT162b2 (Pfizer) COVID-19 vaccination primary series. Before death, he exhibited symptoms of a mild respiratory infection. Despite a healthy medical history and no medication use, the patient’s condition rapidly deteriorated and he experienced severe respiratory distress, followed by cardiopulmonary arrest with evidence of profuse pulmonary bleeding. Autopsy findings revealed massive lung congestion without embolism, normal heart size, moderate coronary atherosclerosis without myocardial infarction, and no evidence of other hemorrhagic events. The patient tested negative for COVID-19 and other respiratory pathogens at autopsy. Despite these findings, the medical examiner determined the cause of death was attributed to atherosclerotic and hypertensive cardiovascular disease, without considering the recent pulmonary hemorrhage and unremarkable medical history. Investigation into the vaccine batch indicated a higher-than-average number of serious adverse events, including fatalities. The patient's BNT162b2 batch was among the top 2.8% for reported deaths. Moreover, the autopsy failed to investigate potential contributions from the vaccine, such as the presence of the Spike protein or related antibodies. The evidence suggests that the pulmonary hemorrhage, exacerbated by a viral infection, was the immediate cause of death, with the COVID-19 vaccine potentially playing a role in the development of cardiopulmonary pathology and hemorrhage. We propose autopsy protocols for COVID-19 vaccine recipients to better investigate vaccine-related pathologies among those with one or more prior injections.

Background and Objectives: The relevance of red flags in serious spinal pathology (SSP) evolved throughout the last years. Recently, new considerations have been proposed to expand the consideration of red flags. The purpose of this study was to determine, approve and test a model for the triage and manage-ment process of SSP based on the latest data available in the literature. Materials and Methods: The SSP model was initially built on the basis of a literature re-view. The model was further determined and approved by an expert panel us-ing a Delphi process. Finally, clinical scenario were used to test the applicabil-ity of the model. Results: After three rounds of Delphi process, panellists reached a consensus on a final version of the model. The use of clinical scenari-os by experts bring about reflexive elements both on the determined model and on the evocative SSP of the clinical cases. Conclusions: The validation of the model and its implementation in the clinical field could help assess the skills of first-line practitioners managing spinal painful patients. To this end, the devel-opment of additional clinical scenarios fitting with the determined model should be further considered.

Tumor cells evolve in a complex and heterogeneous environment composed of different cell types and an extracellular matrix. Current 2D culture methods are very limited in their ability to mimic the cancer cell environment. In recent years, various 3D models of cancer cells have been developed, notably in the form of spheroids/organoids, using scaffold or cancer-on-chip devices. However, these models have the disadvantage of not being able to precisely control the organization of multiple cell types in complex architecture and are sometimes not very reproducible in their production, and this is especially true for spheroids. Three-dimensional bioprinting can produce complex, multi-cellular, and reproducible constructs in which the matrix composition and rigidity can be adapted locally or globally to the tumor model studied. For these reasons, 3D bioprinting seems to be the technique of choice to mimic the tumor microenvironment in vivo as closely as possible. In this review, we discuss different 3D-bioprinting technologies, including bioinks and crosslinkers that can be used for in vitro cancer models, and the techniques used to study cells grown in hydrogels; finally, we provide some applications of bioprinted cancer models.

Many applications in the context of Industry 4.0 require precise localization. However, indoor localization remains an open problem, especially in complex environments such as industrial environments. In recent years, we have seen the emergence of Ultra WideBand (UWB) localization systems. The aim of this article is to evaluate the performance of a UWB system to estimate the position of a person moving in an indoor environment. To do so, we implemented an experimental protocol to evaluate the accuracy of the UWB system both statically and dynamically. The UWB system is compared to a ground truth obtained by a motion capture system with a millimetric accuracy.

Hemicellulose is one of the most important natural polysaccharides in nature. Hemicellulose from different sources varies in chemical composition and structure, which in turn affects the modification effects and industrial applications. Grain and oil by-products (GOBP) are important raw materials for hemicellulose. This article reviews the modification methods of hemicellulose in GOBP. The effects of chemical and physical modification methods on the properties of hemicellulose biomaterials were evaluated. The potential applications of GOBP hemicellulose in films, hydrogel, Three-dimensional (3D) printing and adsorbent are discussed. Future research directions and recommendations are also proposed to provide theoretical foundations and technical support for the efficient utilization of these by-products.

Background: Since the onset of widespread COVID-19 vaccination campaigns, there have been concerns about serious cardiovascular adverse events, including myocarditis, myocardial infarction, and venous thromboembolisms, all of which can lead to cardiopulmonary arrest. This study aimed to estimate excess cardiopulmonary arrest mortality in King County, WA, and investigate any association with COVID-19 vaccination rates. Methods: Data was obtained from the annual King County, WA, EMS reports, the U.S. Census Bureau, and The Tennessean COVID-19 Vaccine Tracker. An exploratory data analysis was performed. Excess deaths were calculated using the 2015-2020 cardiopulmonary arrest mortality trend line. The relationship between excess cardiopulmonary arrest mortality and vaccination rates was analyzed using polynomial regression analysis. A quadratic regression model was used to generate expected population growth trends. The excess mortality model for King County was used to calculate yearly estimates for excess cardiopulmonary arrest fatalities in the USA. Results: Approximately 98% of the King County population received at least one dose of a COVID-19 vaccine by 2023. Our analysis revealed a 25.7% increase in total cardiopulmonary arrests and a 25.4% increase in cardiopulmonary arrest mortality from 2020 to 2023 in King County, WA. Excess cardiopulmonary arrest deaths were estimated to have increased by 1,236% from 2020 to 2023, rising from 11 excess deaths (95% CI: -12, 34) in 2020 to 147 excess deaths (95% CI: 123, 170) in 2023. A quadratic increase in excess cardiopulmonary arrest mortality was observed with higher COVID-19 vaccination rates. The general population of King County sharply declined by 0.94% (21,300) in 2021, deviating from the expected population size. Applying our model from these data to the entire United States yielded 49,240 excess fatal cardiopulmonary arrests from 2021-2023. Conclusions: We identified a very strong ecological and temporal association between excess cardiopulmonary arrest mortality and the COVID-19 vaccination campaign, which resulted in high vaccination rates. The biological plausibility of death from acute cardiac and pulmonary causes after COVID-19 vaccination has been previously demonstrated and is concerning given these real-world observations. Urgent further research is needed to determine if similar trends are observed in other regions with attention to risk mitigation for incident events and improved survival with resuscitation.

Targeted radionuclide therapy is become increasingly prominent as a nuclear medicine subspe-cialty. For many decades, treatment with radionuclides has been mainly restricted to the use of iodine-131 in thyroid disorders. Currently, radiopharmaceuticals, consisting of a radionuclide coupled to a vector that binds to a desired biological target with high specificity, are being de-veloped. The objective is to be as selective as possible at the tumor level, while limiting the dose received at the healthy tissue level. In recent years, a better understanding of molecular mecha-nisms of cancer, as well as the appearance of innovative targeting agents (antibodies, peptides, small molecules) and the availability of new radioisotopes, have enabled considerable advances in the field of vectorized internal radiotherapy with a better therapeutic efficacy, radiation safety and personalized treatments. For instance, targeting the tumor microenvironment, instead of the cancer cells, now appears as particularly attractive. Several radiopharmaceuticals for therapeutic targeting have shown clinical value in severals types of tumors and have been or will soon be approved and authorized for clinical use.

Prolonged application (&gt; 20 minutes) of LV on muscles or tendons is known to reduce maximal isometric strength. However, the effect of short vibration durations (&lt; 6 minutes) is still unknown. In fourteen participants, the changes in maximal voluntary isometric contraction (MVIC) were measured after 1, 3, and 6 minutes of rest (CONT) or local vibration (LV) over the quadricipital tendon (frequency: 100 Hz; amplitude: 0.5mm). Before and after each condition, the amplitude of the twitch induced by a 100 Hz potentiated electrical doublet (PDPOT), relative electromyographic activity of the vastus medialis and rectus femoris muscle during the MVIC (RMSMVIC.M-1), the torque developed 50 ms after the onset of contraction (T50) and the voluntary activation level (VAL) were evaluated. None of the three LV durations significantly changed MVIC compared with the control condition (p = .379). Indices of central (i.e., VAL, T50, RMSMVIC.M-1) and peripheral (PDPOT) fatigue were unaffected (p &gt; .147). In conclusion, a short duration of LV (&lt;6min) on a voluminous muscle group, does not impair maximal force production nor induce any central or peripherical fatigue.

Background: Chronic lower limb ulcers (CLLU) have an important burden to the individual and the healthcare system. However, there is a lack of information about the cost of CLLU in Argentina.Objective: To determinate the number and cost of consultation and hospitalization associated to CLLU in a public hospital in Argentina. Methods: Retrospective observational study. Cost estimation were calculated based on days of stay, treatments and laboratory tests in a inpatient population and the number of consultations, treatments and laboratory tests, in a outpatient population. Results: In 2013 and 2014, the overall number of consultation with ICD-10 codes was 7,224 and the number of inpatient was 359. The mean age for male and female outpatient consultations was 59.53(±13.06) years and 59.04(±10.93), respectively. For CLLU male and female inpatient, the mean age was 63.9(±10.4) years and 54.5(±8.6) years, respectively. The length of stay was 22.88 days. There was a mean of 0.41 surgeries per patient where 25% were amputations. The mean annual cost in a single public hospital was US$4,053.65 per inpatient and US$3,589.24 per outpatient. Conclusion: Cost information allows new public health policies to reduce socioeconomic burden due to CLLU.

The impact of large atmospheric attenuation events on data quality and availability is a critical aspect for future altimetry missions based on Ka-band altimetry. The SARAL/AltiKa mission and its Ka-band nadir altimeter offer a unique opportunity to assess this impact. Previous publications (Tournadre et al. 2009, 2015) already analyzed the impact of rain on the waveforms at Ka-band and proposed a definition of an elaborate rain flag. This notion tends to give a simpler black and white view of the atmospheric attenuation when the effect on the altimeter measurement is intense. But in practice, there is continuum of measurements that may be partially distorted or corrupted by rain events. The present study proposes a wider point of view , the ACECAL approach providing statistics on rain cells occurrences as well as their amplitude and their size, as guidelines for future Ka-band missions concerning the impact of the atmosphere. At global scale, 1 % of the measurements are affected by an attenuation larger than 23 dB and 10 % of the atmospheric attenuation events have a size larger than 40 km. This study demonstrates that the data quality and availability over some regions of particular interest for oceanography as Gulf Stream, North Pacific and Brazil currents could be affected compared to global statistics. It also opens some perspectives on the benefits that the community could be drawn from the systematic distribution of the rain cells parameters as secondary products of altimetry missions.

The dynamics of surface and sub-surface water events can lead to slope instability resulting in anomalies such as slough slides on earthen levees. Early detection of these anomalies by a remote sensing approach could save time versus direct assessment. We have implemented a supervised Mahalanobis distance classification algorithm for the detection of slough slides on levees using complex polarimetric Synthetic Aperture Radar (polSAR) data. The classifier output was followed by a spatial majority filter post-processing step which improved the accuracy. The effectiveness of the algorithm is demonstrated using fully quad-polarimetric L-band Synthetic Aperture Radar (SAR) imagery from the NASA Jet Propulsion Laboratory’s (JPL’s) Uninhabited Aerial Vehicle Synthetic Aperture Radar (UAVSAR). The study area is a section of the lower Mississippi River valley in the southern USA. Slide detection accuracy of up to 98 percent was achieved, although the number of available slides examples was small.

(1) Background: Loss of weight is one of the practices which have been identified as key in reducing the risk of various forms of cancer. Therefore, this study is a systematic review and meta-analysis of studies related to the topic of loss of weight and risk of cancer and addresses the question, ‘does losing weight reduce the risk of cancer?’ Its purpose is to identify current high-quality evidence on such a question and synthesize such evidence before summarizing it given specific data attributes to improve decision-making processes on cancer management. (2) Methods: Research studies were identified from four main databases: PubMed, Science Direct, Google scholar, and Medline. A systematic review and meta-analysis of such studies were then conducted to reveal the most current evidence on the research topic. (3) Results: The studies showed that losing weight reduces cancer risk. Nonetheless, such intervention is not necessarily effective, especially in cases where patients may be at risk of developing cancer due to other risk factors. (4) Conclusions: The current study concludes that there is a need to implement effective interventions such as physical exercise, dietary restrictions, or both that can be effective in reducing weight to reduce the risk of cancer.

Water pollution is the main cause of global ecological degradation and seriously affects people's water supply. In order to respond to the water environmental protection policy and provide management departments with a basis for refining water quality, this paper used the environmental Gini coefficient (EGC) method based on four indicators such as water environmental capacity, population, land area, and gross domestic production (GDP) to represent social factors, economic factors, and environmental factors, respectively. After the optimization, for COD, the EGC based on the land area was 0.30, EGC based on population was 0.21, EGC based on environment capacity was 0.02, and the EGC based on GDP was 0.45, and the sum of EGC was 0.962. From this result, we observed that the change in the Gini coefficient of each indicator was not very big. Hence, the most significant change in the Gini coefficient was that of GDP, with a higher rate than other criteria. Then, the COD, AND, and TP discharge allocation model was constructed to obtain the total allocated discharge permit in Lushui Basin. The results found that the total discharge permit allocation of COD, AN, and TP to the Lushui basin were 51483.304 tons/year, 843.119 tons/year, and 340.926 tons/year, respectively. Based on the GIS spatial analysis technology, the distribution of unfair factors that cause pollution inequity was investigated. Finally, the reduction measures were proposed to implement environmental supervision and strengthen water environment management strictly.

In the United States, obesity is prevalent, and it could be described as a pandemic. Obesity is excessive fat accumulation, leading to a BMI ≥ 30 (Fruh, 2017). Surveys conducted by the CDC show that the obesity prevalence in the US is on the rise, as several obese people rose from 30.5% to 41.9% between 1999 and 2020 (Bryan et al., 2021). During the same time, several people suffering from severe obesity rose from 4.7% to 9.2% (Bryan et al., 2021). Additionally, childhood obesity is on the rise. Statistics indicate that between 2017-2020 over 19.7% of children and adolescents aged 2-19 years had obesity. During the same period, obesity prevalence in children aged 2-5 years, 6-11 years, and 12-19 years olds was 12.7%, 20.7%, and 22.2%, respectively (Bryan et al., 2021). With so many people suffering from obesity, the WHO declared it a public health crisis (WHO, 2020). The COVID-19 pandemic further exacerbated the prevalence of obesity in the US. According to the surveys, there was a 4.4% increase in obesity between 2019 to March 2020 due to lifestyle changes that were put on people during the COVID-19 pandemic (Akter et al., 2022). Many comorbidities are associated with obesity. Without adequate health interventions, millions of people could suffer severe health disorders like respiratory problems, type II diabetes, psychological issues, gastrointestinal disorders, and cardiovascular diseases. It is also essential to develop health interventions to mitigate obesity due to its strain on the healthcare system. Research shows that people suffering from obesity spend $2,505 more than people with average weight on healthcare (Cawley et al., 2021). Obesity has financial ramifications in every healthcare category: inpatient, outpatient, and prescription drugs (Cawley et al., 2021). One essential action toward the efforts to mitigate the soaring obesity rates is understanding the demographic inequities across populations and how they can be resolved.

Oncological patients need the proper doses of medications to facilitate their recovery. The two basic approaches used in dosing Monoclonal Antibodies (mAbs) are fixed-dose combination and variable dosing. In Fixed-Dose Combination Drugs (FDCs), two or more active components are combined in a single formulation at a predetermined dose. Variable dosage, which has long been the industry standard, is the polar opposite of this approach. The body changes over time; the Body Surface Area (BSA) in square meters is often used as a Measure (m2). This study uses a systematic review. Most mAbs used in oncology are predominantly given as cytotoxic anticancer drugs using body-size-based (variable) regimens. Despite the benefits of fixed-dose, variable dosing has become the industry standard, despite being criticized for ineffectiveness. While variable dosing has some advantages, the prevalent view is that continuous dosing has significant advantages based on the balance of probabilities. After assessing each alternative, including its benefits and drawbacks, history of use, and suitability in the current context, fixed dosing emerges as a viable option.

While the two primary risk factors for head and neck squamous cell carcinoma (HNSCC) are alcohol and tobacco, viruses account for an important and significant upward trend in HNSCC incidence. Human papillomavirus (HPV) is the causative agent for a subset of oropharyngeal squamous cell carcinoma (OPSCC)—a cancer that is impacting a rapidly growing group of typically middle-aged non-smoking white males. While HPV is a ubiquitously present virus (with about 7% of the population having oral HPV infection at any one time), only 1% of those infected develop OPSCC— suggesting that additional cofactors or coinfections may be required. Epstein-Barr virus (EBV) is a similarly ubiquitous virus that is strongly linked to nasopharyngeal carcinoma (NPC). Both of these viruses cause cellular transformation and chronic inflammation. While dysbiosis of the human microbiome has been associated with similar chronic inflammation and the pathogenesis of mucosal diseases (including OPSCC and NPC), a significant knowledge gap remains in understanding the role of bacterial-viral interactions in the initiation, development, and progression of head and neck cancers. In this review, we utilize the known associations of HPV with OPSCC and EBV with NPC to investigate these interactions. We thoroughly review the literature and highlight how perturbations of the pharyngeal microbiome may impact host-microbiome-tumor-viral interactions—leading to tumor growth.

Development of methods and algorithms to predict the effect of mutations on protein stability, protein-protein, and protein-DNA/RNA binding is necessitated by the needs of protein engineering and for understanding the molecular mechanism of disease-causing variants. The vast majority of the leading methods are either methods with adjustable parameters or machine learning algorithms, both requiring a database of experimentally measured folding and binding free energy changes. These databases are collections of experimental data taken from scientific investigations typically aimed at probing the role of particular residue on the above-mentioned thermodynamics characteristics, i.e., the mutations are not introduced at random and do not necessarily represent mutations originating from single nucleotide variant (SNV). Thus, the reported performance of the leading algorithms assessed on these databases or other limited cases, may not be applicable for predicting the effect of SNVs seen in the human population. Indeed, we demonstrate that the SNVs and non-SNVs are not equally presented in the corresponding databases and the distribution of the free energy changes are not the same. Furthermore, the Pearson correlation coefficients (PCCs) obtained on cases involving SNVs are less impressive than for non-SNVs, indicating that caution should be used in applying them to reveal the effect of human SNVs. All methods are found to underestimate the energy changes by roughly a factor of 2.

French academies almost all implement reactivity drills and small-sided games (SSG) the day preceding a match (MD-1). The present study aimed to determine the physical impact of different training durations on MD-1 on the subsequent matchday performance (MD). Eleven elite U19 academy soccer players con-ducted three typical training sessions lasting 45min (TS45), 60min (TS60), and 75min (TS75) on MD-1. Dur-ing TS60, warm-up, reactivity and SSG were 10, 15, and 24min, respectively, plus coaches' feedback or wa-ter breaks. Durations decreased and increased by 25% for TS45 and TS75, respectively. Tests were con-ducted on MD-4 (CONTROL) and MD before the match (TEST). Tests consisted of a counter movement jump (CMJ), 20m sprint, Illinois agility test (IAT), and Hooper questionnaire. CONTROL values were simi-lar over the three experimental conditions. TEST on MD revealed greater CMJ for TS45 (42.7 ± 5.1cm) compared to TS60 (40.5 ± 5.5cm, p=0.032) and TS75 (40.9 ± 5.7cm, p=0.037). 20m time was lower for TS45 (3.07 ± 0.10s, p<0.001) and TS60 (3.13 ± 0.10s, p=0.017) compared to TS75 (3.20 ± 0.10s). IAT time was lower on TS45 (14.82 ± 0.49s) compared to TS60 (15.43 ± 0.29s, p<0.001) and TS75 (15.24 ± 0.33s, p=0.006). Further-more, the Hooper index was lower at TEST for TS45 (7.64 ± 1.50) compared to TS60 (11.00 ± 3.49, p=0.014) and TS75 (9.73 ± 2.41, p=0.045) indicating a better readiness level. We concluded that as training session duration increases, performance decreases on MD. A 45min training session including reactivity and SSG exercises is therefore recommended on MD-1.

A new picture of the Josephson effect is devised. The radio-frequency (RF) signal, observed in a Josephson junction, is shown to stem from bound electrons, tunneling periodically through the insulating film. This holds also for the microwave mediated tunneling. The Josephson effect is found to be conditioned by the same prerequisite worked out previously for persistent currents, thermal equilibrium and occurence of superconductivity. The observed negative resistance behaviour is shown to originate from the interplay between the normal and superconducting currents.

Diagnosis and prognosis of failures for aircrafts’ integrity are some of the most important regular functionalities in complex and safety-critical aircraft structures. Further, development of failure diagnostic tools such as Non-Destructive Testing (NDT) techniques, in particular, for aircraft composite materials, has been seen as a subject of intensive research over the last decades. The need for diagnostic and prognostic tools for composite materials in aircraft applications rises and draws increasing attention. Yet, there is still an ongoing need for developing new failure diagnostic tools to respond to the rapid industrial development and complex machine design. Such tools will ease the early detection and isolation of developing defects and the prediction of damages propagation; thus allowing for early implementation of preventive maintenance and serve as a countermeasure to the potential of catastrophic failure. In this paper, following a short introductory summary and definitions, this paper provides a brief literature review of recent research on failure diagnosis of composite materials with an emphasis on the use of NDT techniques in aerospace industry. In addition to this, within a some of significant NDT application extents, prognosis of composites is also briefly discussed.

In recent years, advances in science, technology, and the way in which we view our world have led to anincreasingly broad use of the term “intelligence”. As we learn more about biological systems, we find more and more examples of complex and precise adaptive behavior in animals and plants. Similarly, as we build more complex computational systems, we recognize the emergence of highly sophisticated structures capable of solving increasingly complex problems. These behaviors show characteristics in common with the sort of complex behaviors and learning capabilities we find in humans, and therefore it is common to see them referred to as “intelligent”. These analogies are problematic as the term "intelligence" is inextricably associated with human-like capabilities. While these issues have been discussed by leading researchers of AI and renowned psychologists and biologists highlighting the commonalities and differences between AI and biological intelligence, there have been few rigorous attempts to create an interdisciplinary approach to the modern problem of intelligence. This article proposes a comparative framework to discuss what we call “purposeful behavior”, a characteristic shared by systems capable of gathering and processing information from their surroundings and modifying their actions in order to fulfill a series of implicit or explicit goals. Our aim is twofold: on the one hand, the term purposeful behavior allows us to describe the behavior of these systems without using the term "intelligence", avoiding the comparison with human capabilities. On the other hand, we hope that our framework encourages interdisciplinary discussion to help advance our understanding of the relationships among different systems and their capabilities.

The new barrier mode in Apache Spark allows embedding distributed deep learning training as a Spark stage to simplify the distributed training workflow. In Spark, a task in a stage doesn’t depend on any other tasks in the same stage, and hence it can be scheduled independently. However, several algorithms require more sophisticated inter-task communications, similar to the MPI paradigm. By combining distributed message passing (using asynchronous network IO), OpenJDK’s new auto-vectorization and Spark’s barrier execution mode, we can add non-map/reduce based algorithms, such as Cannon’s distributed matrix multiplication to Spark. We document an efficient distributed matrix multiplication using Cannon’s algorithm, which improves significantly on the performance of the existing MLlib implementation. Used within a barrier task, the algorithm described herein results in an up to 24% performance increase on a 10,000x10,000 square matrix with a significantly lower memory footprint. Applications of efficient matrix multiplication include, among others, accelerating the training and implementation of deep convolutional neural network based workloads, and thus such efficient algorithms can play a ground-breaking role in faster, more efficient execution of even the most complicated machine learning tasks

A classical model is presented for persistent currents in superconductors. Their existence is argued to be warranted because their decay would violate the second law of thermodynamics. This conclusion is achieved by analyzing comparatively Ohm's law and the Joule effect in normal metals and superconducting materials. Whereas Ohm's law applies in identical terms in both cases, the Joule effect is shown to cause the temperature of a superconducting sample to \textit{decrease}. An experiment is proposed to check the validity of this work in superconductors of both types I and II.

Stem cells can be used to treat diabetic mellitus and complications. ω3-docosahexaenoic acid (DHA) derived lipid mediators are inflammation-resolving and protective. This study found novel DHA-derived 7S,14R-dihydroxy-4Z,8E,10Z,12E,16Z,19Z-docosahexaenoic acid (7S,14R-diHDHA), a maresin-1 stereoisomer biosynthesized by leukocytes and related enzymes. Moreover, 7S,14R-diHDHA can enhance mesenchymal stem cell (MSC) functions in the amelioration of diabetic mellitus and retinal pericyte loss in diabetic db/db mice. MSCs treated with 7S,14R-diHDHA were delivered into db/db mice i.v. every 5 days for 35 days. Blood glucose levels in diabetic mice were lowered by 7S,14R-diHDHA-treated MSCs compared to control and untreated MSC groups, accompanied by improved glucose tolerance and higher blood insulin levels. 7S,14R-diHDHA-treated MSCs increased insulin+ β-cell ratio and decreased glucogan+ α-cell ratio in islets, as well as reduced macrophages in pancreas. 7S,14R-diHDHA induced MSC functions in promoting MIN6 β-cell viability and insulin secretion. 7S,14R-diHDHA induced MSC paracrine functions by increasing the generation of hepatocyte growth factor and vascular endothelial growth factor. Furthermore, 7S,14R-diHDHA enhanced MSC functions to ameliorate diabetes-caused pericyte loss in diabetic retinopathy by increasing their density in retina in db/db mice. Our findings provide a novel strategy for improving therapy for diabetes and diabetic retinopathy using 7S,14R-diHDHA-primed MSCs.

Two solvated rhenium(IV) complexes with formula [ReCl4(bpym)]·MeCN (1) and [ReCl4(bpym)]·CH3COOH·H2O (2) [bpym = 2,2'-bipyrimidine] have been prepared and characterized by means of Fourier transform infrared spectroscopy (FT–IR), scanning electron microscopy and energy dispersive X-ray analysis (SEM–EDX), single-crystal X-ray diffraction (XRD) and SQUID magnetometer. 1 and 2 crystallize in the monoclinic system with space groups P21/n and P21/c, respectively. In both compounds, the Re(IV) ion is six-coordinate and bound to four chloride ions and two nitrogen atoms of a 2,2’-bipyrimidine molecule forming a distorted octahedral geometry around the metal ion. In the crystal packing of 1 and 2, intermolecular halogen⋯halogen and π⋯halogen type interactions are present. Hydrogen bonds take place only in the crystal structure of 2. Both compounds exhibit an akin crystal framework based on halogen bonds. Variable-temperature dc magnetic susceptibility measurements performed on microcrystalline samples of 1 and 2 show a similar magnetic behavior for both compounds, with antiferromagnetic exchange between the Re(IV) ions connected mainly through intermolecular Re-Cl···Cl-Re interactions.

Titanium oxynitride thin films are deposited by DC reactive magnetron sputtering. A pure titanium target is sputtered in a reactive atmosphere composed of argon, oxygen and nitrogen gases. The oxygen mass flow rate as well as that of the nitrogen gas are both pulsed during the deposition time using an independent and rectangular signal for each reactive gas. A constant pulsing period T = 45 s is applied for both reactive gases and a delay time  of 34 s between N2 and O2 injection times is set for all depositions. Oxygen and nitrogen duty cycles are systematically and independently changed from 0 to 100% of their pulsing period. From real time measurements of the Ti target potential and total sputtering pressure, it is shown that the reactive process alternates between oxidized, nitrided and elemental sputtering modes as a function of the oxygen and nitrogen injection times. The full poisoning of the Ti target surface by oxygen and/or nitrogen can be avoided for some given ranges of O2 and N2 duty cycles. Deposition rates of titanium oxynitride films are substantially enhanced and can be adjusted between that of pure Ti and TiN films with a gradual transition of their optical transmittance in the visible range. These results support that titanium oxynitride compounds exhibiting absorbent to transparent behaviors can be precisely sputter-deposited by means of a two reactive gases pulsing process.

Electrowetting – induced detachment of droplets from solid surfaces is important for numerous applications in the fields of heat transfer and fluid mechanics. The forced oscillations of droplets on solid surfaces and their ability to detach are studied. In this study the process is efficiently simulated by implementing a powerful methodology developed by our team. Our results agree with experiments, showing that optimal detachment, in terms of actuation energy, is achieved when the application of voltage is synchronized with the spreading time of the droplet. Under these conditions, the droplet oscillates with a period close to that of a mirrored Rayleigh droplet. The relation between the droplet’s oscillation period and its physical properties is examined. During voltage-droplet synchronization, the droplet’s ability to detach depends mostly on its contact angle, its viscosity, and the applied voltage. An energy analysis is also conducted, revealing how energy is supplied to the droplet by electrowetting-induced detachment.

This paper assesses the performance of an embankment constructed in 2010 with a stabilised expansive soil. Two types of treatment were employed at construction time: 4% lime and a mix of 2% lime and 3% cement. A sampling campaign was carried out in 2021 to evaluate the long-term performance of the stabilised soil properties. To assess the compressibility of the soil, oedometer tests were carried out on samples from different parts of the embankment. The results were compared to the compression curve of the untreated soil, also sampled in the same embankment. Complementary shrinkage tests were performed to investigate the effect of the treatment on swelling and shrinkage. The obtained results showed that the behaviour of the material from the outer part was similar to the mechanical performance of the untreated soil, demonstrating strong alteration in the effect of both treatments over time. This alteration was noticeable to a distance of approximately two metres from the external surface. Beyond this distance, the performance of the soil was comparable to the behaviour of recently treated soil. These observations, similar for each treatment dosage, raise questions as to the durability of the treatment on the outer part of the backfill.

Crop breeding is as ancient as the invention of cultivation. In essence, the objective of crop breeding is to improve plant fitness under human cultivation conditions, making crops more productive while maintaining consistency in life cycle and quality. The applications of predictive breeding has been gaining momentum in agricultural industry and public breeding programs for the last decade, in the aftermath of genomic selection being recognized and widely applied for accelerating genetic gain in breeding programs. The massive amounts of data that has been generated by industry and farmers year after year through several decades has finally been recognized as an asset. A wide range of analytical methods such as machine learning, deep learning and artificial intelligence that were initially developed for diverse quantitative disciplines are now being adopted to crop breeding decision making processes. New technologies are currently being developed that would enable integration of data from various domains such as geospatial variables and a multitude of phenotypic responses as well as genetic information, in order to identify, develop and improve crop faster via partial or full automation of the decisions that pertain to variety development. Here we will discuss and summarize efforts from public and private domains for predictive analytics, and its applications to crop breeding and agricultural product development, and provide suggestions for future research.

There is a large body of research on determining the impact of field variability of soil on crop yields. In contrast, site-specific information about crop responses to agronomic treatments is less frequent. On-Farm Precision Experimentation (OFPE) brings important information to understand the spatial variation of crop response to agronomic practices and thus to improve agronomic decisions. The objective of this work was to investigate the spatial variability of corn yield responses to nitrogen and seed rates using OFPE in four fields in the US Midwest. Geographically weighted regression was applied to generate local regression coefficients, which were used to delineate response zones in each field. The results showed the existence of great potential to adjust the rates of these inputs according to the response of each zone identified by the proposed method. The results of this study can be applied to reevaluate expectations on variable rate prescriptions guided largely by soil and variability.

Background: Nowadays vital signs in clinics are electronically monitored excepted for urine output which still requires, manual recording, which is subject to human errors. We, in-vitro, assessed in this study the ability a novel electronic device to measure by a combination of two different methods, the real time flow-output, like urine output. Methods: Flow or urine output was measured by a combination technique of gravimetry using a dynamometer and capacitive sensing to improve precision. Data were obtained in 3 different situations, low, medium, and high flow. Results: Three different situations were tested: full or empty dead space and Pasteur’s chamber. The differences between the injected and measured volume varies from 0 to 5 ml representing a maximal error of 3 % regardless of the volume injected and the flow in ml/hour. The capacitive sensors behave as expected with a parallel curve of the expected and measured flow. Conclusion: We have shown in this in-vitro study that the combination of gravimetry and capacitive sensors analysis allow accurate measurement of volume and flow-output. Clinical trials should be conducted to confirm its usefulness in urine output measurement in the real life.

This study compared the relative effect of two trace mineral supplementation strategies recom-mended in France for newborn beef calves. 600 calves were supplemented with 20 mg oral sele-nium (OTM group) at birth (D0) or by injection (ITM group) of a multi-mineral solution (60 mg of Zn, 10 mg of Mn, 15 mg of Cu, 5 mg of Se) on D0, D30 and D60. Mortality and the incidence rate of diseases, including diarrhea, omphalitis, pneumonia, as well as medicinal treatments, were recorded from D0 to D210. The incidence rate of omphalitis was significantly lower in the ITM group than in the OTM group (respectively 11% vs. 17%, P = 0.036). The cumulative inci-dence rate of all health troubles was lower in the ITM group than in the OTM group (P=0.007). Except for pneumonia, incidence of diarrhea (24% vs. 22%), use of oral (7% vs. 6%) or IV rehydra-tion therapy (4% vs. 2%) or use of antibiotics (43.3% vs. 38.0%) and mortality (3% vs 2%) were numerically higher in OTM group than in ITM group (n.s.). In this study, ITM supplementation is as efficient as oral supplementation regarding calves' health status. It reduces the risk of ompha-litis at the calf level effectively.

Soybean maturity is a trait of critical importance for the development of new soybean cultivars, nevertheless, its characterization based on visual ratings has many challenges. Unmanned aerial vehicles (UAVs) imagery-based high-throughput phenotyping methodologies have been proposed as an alternative to the traditional visual ratings of pod senescence. However, the lack of scalable and accurate methods to extract the desired information from the images remains a significant bottleneck in breeding programs. The objective of this study was to develop an image-based high-throughput phenotyping system for evaluating soybean maturity in breeding programs. Images were acquired twice a week, starting when the earlier lines began maturation until the latest ones were mature. Two complementary convolutional neural networks (CNN) were developed to predict the maturity date. The first using a single date and the second using the five best image dates identified by the first model. The proposed CNN architecture was validated using more than 15,000 ground truth observations from five trials, including data from three growing seasons and two countries. The trained model showed good generalization capability with a root mean squared error lower than two days in four out of five trials. Four methods of estimating prediction uncertainty showed potential at identifying different sources of errors in the maturity date predictions. The architecture used solves limitations of previous research and can be used at scale in commercial breeding programs.

Cell plasma membranes display a dramatically rich structural complexity characterized by functional sub-wavelength domains with specific lipid and protein composition. Under favorable experimental conditions, patterned morphologies can also be observed in vitro on model systems such as supported membranes or lipid vesicles. Lipid mixtures separating in liquid-ordered and liquid-disordered phases below a demixing temperature play a pivotal role in this context. Protein-protein and protein-lipid interactions also contribute to membrane shaping by promoting small domains or clusters. Such phase separations displaying characteristic length-scales falling in-between the nanoscopic, molecular scale on the one hand and the macroscopic scale on the other hand, are named mesophases in soft condensed matter physics. In this Review, we propose a classification of the diverse mechanisms leading to mesophase separation in biomembranes. We distinguish between mechanisms relying upon equilibrium thermodynamics and those involving out-of-equilibrium mechanisms, notably active membrane recycling. In equilibrium, we show that the mechanisms generically dwell on an up-down symmetry breaking between the upper and lower bilayer leaflets. Symmetry breaking is an ubiquitous mechanism in condensed matter physics at the heart of several important phenomena. In the present case, it can be either spontaneous (domain buckling) or explicit, i.e. due to an external cause (global or local vesicle bending properties). Whenever possible, theoretical predictions and simulation results are confronted to experiments on model systems or living cells, which enables us to identify the most realistic mechanisms from a biological perspective.

The importance of sleep for healthy brain function is widely acknowledged. However, it remains unclear how the internal generation of dreams might facilitate cognitive processes. In this perspective we review a computational approach inspired by artificial intelligence that proposes a framework for how dreams occurring during rapid-eye-movement (REM) sleep can contribute to learning and creativity. In this framework, REM dreams are characterized by an adversarial process that, against the dream reality, tell a discriminator network to classify the internally created sensory activity as real. Such an adversarial dreaming process is shown to facilitate the emergence of real-world semantic representations in higher cortical areas. We further discuss the potential contributions of adversarial dreaming beyond learning, such as balancing fantastic and realistic dream elements, and facilitating the occurrence of creative insights. We characterize non-REM (NREM) dreams, where a single hippocampal memory is replayed at a time, as serving a complementary role of improving the robustness of cortical representations to environmental perturbations. We finally explain how subjects can become aware of the adversarial REM dreams, but less of the NREM dreams, and how the awareness phenomenon of wake, dream and lucid dreaming may appear.

Circular Economy (CE) is a growing topic among scholars, industry and government aiming at decoupling economic growth and development from the consumption of finite resources. CE incorporates different meanings, from reduce, reuse and recycle activities to environmental degradation or resource scarcity, and supported by specific indicators to attain sustainable development. However, so far, there has been no agreement to measure how effective an industry/product is in making the transition from linear to circular approaches, particularly those affected the society. This research work aims to perform a systematic literature review (n=60) to analyze and discuss how social aspects have been considered and integrated in the CE research so far. Moreover, this review provides and overview of the literature on social impact within CE, that resulted in three main outputs: a knowledge map of the CE, an analysis of social aspects within CE, and the theories/frameworks used to evaluate social impact of CE. Finally, this study brings to light how CE implementation can affect society and highlights the importance of social dimension in the domains of CE and policy-making community, which could help moving CE towards a sustainable development.

Adult neurogenesis is an evolutionary conserved process occurring in all vertebrates. However, striking differences are observed between the taxa, considering the number of neurogenic niches, the neural stem cell (NSC) identity and brain plasticity under constitutive and injury-induced conditions. Zebrafish has become a popular model for the investigation of the molecular and cellular mechanisms involved in adult neurogenesis. Compared to mammals, the adult zebrafish displays a high number of neurogenic niches distributed throughout the brain. Furthermore, it exhibits a strong regenerative capacity without scar formation or any obvious disabilities. In this review, we will first discuss the similarities and differences regarding (i) the distribution of neurogenic niches in the brain of adult zebrafish and mammals (mainly mouse) and (ii) the nature of the neural stem cells within the main telencephalic niches. In the second part, we will describe the cascade of cellular events occurring after telencephalic injury in zebrafish and mouse. Our study clearly shows that most early events happening right after the brain injury are shared between zebrafish and mouse including cell death, microglia and oligodendrocyte recruitment, as well as injury-induced neurogenesis. In mammals one of the consequences following an injury is the formation of a glial scar that is persistent. This is not the case in zebrafish, which may be one of the main reasons that zebrafish display a higher regenerative capacity.

The number of long-term cancer survivors increases continually. Understanding their needs is crucial to ensure an adequate follow-up. The aim of our study was to summarize the current literature concerning needs and what in-fluences these needs. A Scoping review of systematic reviews was conducted according to the recommendations of the Joanna Briggs Institute (JBI). Four electronic databases were searched. Of 414 retrieved papers, 11 met the eligi-bility criteria. Needs were aggregated into six domains (health-related information, health system, mental, practical, relationship and physical) and 15 categories. The lack of adequate information and the lack of access and/or conti-nuity of supportive care were the most prominent needs. Female gender, younger age, a low level of family and/or social support, and higher educational level were identified as risk factors. Employment and relationship status can affect the needs both in a positive or negative way. The weeks or months after the end of the treatments are partic-ularly critical and needs can be emphasized during this period. Cancer survivors could also leave positive changes. The variety of needs affects the quality of life of cancer survivors. The current Swiss healthcare system is not de-signed to support these people. Needs assessments should be systematically provided to ensure a better awareness on the part of health professionals and to allow an individual, holistic, and integrated follow-up.

One century ago, ferroelectricity and then piezoelectricity were discovered using Rochelle salt crystals. Today, modern societies are invited to switch towards a resilient and circular economy model. In this context, this work proposes a method to manufacture piezoelectric devices made from agro-resources such as tartric acid and polylactide significantly reducing the energy budget without requiring any sophisticated equipement. These piezoelectric devices are manufactured by liquid phase epitaxy grown Rochelle salt (RS) crystals into a 3D printed poly(Lactic acid) (PLA) matrix being the artificial squared meshes which mimic the natural wood anatomy. This composite material can easily be produced in any fablab with renewable materials and at low processsing temperatures, reducing then the total energy consumed. Manufactured biodegradable samples are fully recyclable and have good piezoelectric properties without any pooling step. The measured piezoelectric coefficients of manufactured samples are higher than many piezoelectric polymers such as PVDF-TrFE.

In this paper, we delve into the realm of aspect-level sentiment analysis, a sophisticated analytical task focused on pinpointing and interpreting the sentiment directed towards specific elements within a sentence. Traditional methods in this domain, primarily based on neural networks, have often overlooked the critical role of syntactic structures in sentences. To bridge this gap, we have developed the Syntax-Enhanced Sentiment Graph Network (SentiSyn). This pioneering model represents a significant step forward in aspect-level sentiment analysis, bringing to the forefront the utilization of word dependency relationships to enrich sentiment analysis. SentiSyn stands out by its innovative use of a dependency graph, a tool that meticulously maps out the intricate web of syntactic relationships surrounding a target aspect in a sentence. This approach allows SentiSyn to effectively capture and channel sentiment-related characteristics that are deeply rooted in the syntactic context of the aspect target. By doing so, SentiSyn unlocks a deeper understanding of sentiment dynamics in textual content, enabling a more nuanced and accurate sentiment analysis. Our comprehensive experimental evaluation of SentiSyn showcases its remarkable capabilities. When combined with advanced embedding techniques like GloVe and BERT, SentiSyn demonstrates a superior performance edge over several existing sentiment analysis methods. This performance leap is not just incremental; it represents a significant enhancement in the field of sentiment analysis, underscoring the importance of syntactic context in understanding sentiments. Furthermore, our analysis delves into how SentiSyn effectively leverages these embeddings to gain a more profound and contextually rich insight into sentiment dynamics. The results from our tests indicate that SentiSyn, with its unique approach to integrating syntactic structures and advanced embeddings, sets a new benchmark in aspect-level sentiment analysis, offering both enhanced accuracy and deeper sentiment understanding.

Background: COVID-19 vaccines have been linked to myocarditis which in some circumstances can be fatal. This systematic review aims to investigate potential causal links between COVID-19 vaccines and death from myocarditis using post-mortem analysis. Methods: We performed a systematic review of all published autopsy reports involving COVID-19 vaccination-related myocarditis through July 3^rd, 2023. All autopsy studies that include COVID-19 vaccine-induced myocarditis as a possible cause of death were included, without imposing any additional restrictions. Causality in each case was determined by three independent reviewers with cardiac pathology experience and expertise. Results: We initially identified 1,691 studies and, after screening for our inclusion criteria, included 14 papers that contained 28 autopsy cases. The cardiovascular system was the only organ system affected in 26 cases. In 2 cases, myocarditis was characterized as a consequence from multisystem inflammatory syndrome (MIS). The mean and median number of days from last COVID-19 vaccination until death was 6.2 and 3 days, respectively. Most of the deaths occurred within a week from the last injection. We established that all 28 deaths were causally linked to COVID-19 vaccination by independent adjudication. Conclusions: The temporal relationship, internal and external consistency seen among cases in this review with known COVID-19 vaccine-induced myocarditis, its pathobiological mechanisms and related excess death, complemented with autopsy confirmation, independent adjudication, and application of the Bradford Hill criteria to the overall epidemiology of vaccine myocarditis, suggests there is a high likelihood of a causal link between COVID-19 vaccines and death from suspected myocarditis in cases where sudden, unexpected death has occurred in a vaccinated person. Urgent investigation is required for the purpose of risk stratification and mitigation in order to reduce the population occurrence of fatal COVID-19 vaccine-induced myocarditis.

The Herpes Virus Entry Mediator (HVEM) delivers a negative signal to T cells mainly through the B and T Lymphocyte Attenuator (BTLA) molecule and thus, could represent a novel immune checkpoint during an anti-tumor immune response. A formal demonstration that HVEM can be targeted for cancer immunotherapy is however still lacking. Here, we first show that HVEM and BTLA were associated to a worse prognosis in patients with prostate adenocarcinomas, indicating a detrimental role for this pair of molecule during prostate cancer progression. We then show that a monoclonal antibody to human HVEM significantly impacted the growth of a prostate cancer cell line in immuno-compromised NOD.SCID.gc-null mice reconstituted with human T cells. Using CRISPR/Cas9, we showed that HVEM expression by the tumor was mandatory to observe the therapeutic effect. Mechanistically, tumor control was dependent on CD8+ T cells and was associated to an increase in the proliferation and number of tumor-infiltrating leukocytes. Accordingly, the expression of genes belonging to various T cell activation pathways were enriched in tumor infiltrating leukocytes, whereas genes associated with immuno-suppressive pathways were decreased, possibly resulting in modifications of leukocyte adhesion and motility. Finally, we developed a simple in vivo assay in humanized mice to directly demonstrate that HVEM was an immune checkpoint for T-cell mediated tumor control. Our results show that targeting HVEM is a promising strategy for prostate cancer immunotherapy.

Currently, the use of medications during pregnancy in Latin America is common; studies with Latin American samples find that nearly 90% of pregnant women use some medication at least once during pregnancy. Furthermore, approximately 21% of the respondents self-medicated. Worldwide, the prevalence of this disease is 32%. The most common medications are nonsteroidal anti-inflammatory drugs and analgesics. Many of these drugs are available over the counter without a prescription. For this reason, a systematic review of the literature on the adverse effects on the woman and the fetus was performed. Objective: To determine the adverse effects associated with the use of nonsteroidal anti-inflammatory drugs (NSAIDs) on pregnant women and fetuses during pregnancy. Methods: Systematic literature review. The following search strategy was used for the databases: Science Direct, PubMed, Scopus and Web of Science, through September 3, 2022. The population of pregnant women without previous comorbidities was defined. The intervention of interest was the use of NSAIDs during pregnancy. The outcomes of interest were adverse effects for the mother or fetus (weight of the newborn, congenital malformations present in the fetus, systemic effects in the pregnant woman during her gestation period). The types of studies included clinical trials, cohort studies and case‒control studies. Results: 1 study included 2,985 pregnant women without previous comorbidities. The use of aspirin more frequently during pregnancy stands out. The adverse effects on the fetus were preterm birth <37 weeks, low birth weight < 2500 g and increased admission to the neonatal intensive care unit. No adverse effects were found for the mother. Conclusions: There are not enough data indicating that the use of NSAIDs during pregnancy is safe. Some studies show that the use of NSAIDs during pregnancy could be related to problems in the development and growth of the fetus and health effects for the mother during pregnancy, so it is advisable to use these drugs under medical prescription and for the shortest possible time. in the gestation stage.

Obesity is a significant public health concern with higher morbidity. Obesity patients are at risk of severe COVID-19 infection and obesity is a higher risk factor for intensive Care Unit admission in COVID-19 infection. Obesity status affects lung volumes, cardiac structure and hemodynamics. Obesity is associated with a low inflammation state, endothelial dysfunction, hyperinsulinaemia and metabolic disorders. The authors review cardio-respiratory pathophysiological aspects involved in obesity and propose clinical management in obese patients infected by COVD-19.

We have carried out a systematic review of the scientific literature published on PM and, more specifically, on its presence in fish and seafood of interest to the population from Mediterranean area. Given its preference and wide acceptability in the scientific community, we followed the PRISMA. The potential functional and clinical toxicity in humans due to MP in fish must be considered by the chemical composition of the microplastics the presence of PM and its additives, associated contaminants and pathogens in fish and shellfish, as well as the possible effects on human health, requires improving legislation on evaluation and providing a basis for consumer protection.

This paper proposes the configuration of an Organic Rankine Cycle (ORC) coupled to a solar domestic hot water system (SDHWS), with the purpose of analyzing the cogeneration capacity of the system. A simulation of the SDHWS was conducted at different temperatures, observing its performance to determine the amounts of useable heat generated by the solar collector; thus, from an energy balance, the amount of heat that may be used by the ORC could be determined. The working fluid that would be suitable for the temperatures and pressures given in the system were selected. The best fluid for the given conditions of superheated vapor at 120 °C and 604 kPa and a condensation temperature of 60 °C and 115 kPa was acetone. The main parameters for the expander thermodynamic design that may be used in such ORC were obtained with the possibility of generating 443 kWh of annual electric energy, with 6.65 % global efficiency of solar to electric power, or an overall efficiency of the cogeneration system of 56.35 % with a solar collector of 2.84 m².

The nucleosome is a major modulator of DNA accessibility to other cellular factors. Nucleosome positioning has a critical importance in regulating cell processes such as transcription, replication, recombination or DNA repair. The DNA sequence is a major factor influencing the position of nucleosomes on genomes. Different sequence motifs can promote or inhibit the nucleosome formation, thus influencing the accessibility to the DNA. Sequence-encoded nucleosome positioning having functional consequences on cell processes can then be selected or counter-selected during evolution. We review the interplay between sequence evolution and nucleosome positioning evolution. We first focus on the different ways to encode nucleosome positions in the DNA sequence, and to which extent these mechanisms are responsible of genome-wide nucleosome positioning in vivo. Then, we discuss the findings about selection of sequences for their nucleosomal properties. Finally, we illustrate how the nucleosome can directly influence sequence evolution through its interactions with DNA damage and repair mechanisms. This review aims to provide an overview of the mutual influence of sequence evolution and nucleosome positioning evolution, possibly leading to complex evolutionary dynamics.

Background: The aim of this study was to compare energy expenditure (EE) predicted by accelerometery (EEAcc) with indirect calorimetry (EEMETA) in individuals with hemiparesis. Methods: Twenty-four participants (12 with stroke and 12 healthy controls) performed a six-minute walk test (6MWT) during which EEMETA was measured using a portable indirect calorimetry system and EEACC was calculated using Bouten’s equation (1993) with data from a 3-axis accelerometer positioned between L3 and L4. Results: Median EEMETA was 9.85 [8.18;11.89] W·kg-1 in the stroke group, and 5.0 [4.56;5.46] W·kg-1 in the control group. Median EEACC was 8.57 [7.86;11.24] W·kg-1 in the control group and 8.2 [7.05;9.56] W·kg-1 in the stroke group. EEACC and EEMETA were not significantly correlated in either the control (p=0.8) or the stroke groups (p=0.06). The Bland-Altman method showed a mean difference of 1.77±3.65 W·kg-1 between EEACC and EEMETA in the stroke group and -2.08±1.59 W·kg-1 in the controls. Conclusions: The accuracy of the predicted EE, based on the accelerometer and the equations proposed by Bouten et al, is low in individuals with hemiparesis and impaired gait. This combination (sensor and Bouten's equation) is not yet suitable for use as a stand-alone measure in clinical practice for the evaluation of hemiparetic patients.

In this work, the solar light-induced redox photoactivity of the ZnO semiconductor material was used to prepare at room temperature CuxO-ZnO composite catalysts with a control of the chemical state of the copper oxide phase. The preparation of Cu2(I)O-ZnO and Cu(II)O-ZnO composite catalysts was achieved by using Cu(acac)2 in THF-water and Cu(NO3)2 in water as metallic precursor, respectively. Prior to the implementation of the photo-assisted synthesis method, the most efficient photoactive ZnO material was selected among different ZnO materials prepared by the low temperature polyol method and through the precipitation method with carbonates and carbamates as precipitation agent, by taking the photocatalytic degradation of the 4-chlorophenol compound in water under simulated solar light as model reaction. The ZnO support materials were characterized by XRD, BET, TGA, SEM and TEM, and the synthesis method was strongly influencing their photoactivity in terms of 4-chlorophenol degradation and of total organic carbon removal. The most photoactive ZnO material was prepared by precipitation with carbonates and calcined at 300°C, and was taking advantage of a high specific surface area and a small mean crystallite size for achieving a complete 4-chlorophenol mineralization within 70 min of reaction, with a minimum Zn2+ released to the solution due to surface photocorrosion. Beside thermal catalysis applications, this work opened a new route for the facile synthesis of Cu2O-ZnO heterojunction photocatalysts, that could take advantage under solar light of the heterojunction built between the p-type semi-conductor Cu2O with direct visible light band gap and the ZnO semiconductor phase.

Furfuryl alcohol (FA) is a biobased monomer derived from lignocellulosic biomass. The present work describes its polymerization in presence of protic polar solvents, i.e. water or isopropyl alcohol (IPA), using maleic anhydride (MA) as acidic initiator. The polymerization was followed from the liquid to the rubbery state by combining DSC and DMA data. In the liquid state, IPA disrupts the expected reactions during all the FA polymerization due to a stabilization of the furfuryl carbenium center. This causes the initiation of the polymerization at higher temperature, which is also reflected by higher activation energy. In water system, the MA opening allows to start the reaction at lower temperature. A higher pre-exponential factor value is obtained in that case. The DMA study of final branching reaction occurring in the rubbery state has highlighted continuous increase of elastic modulus until 290 °C. This increasing tendency of modulus was exploited to obtain activation energy dependences (Eα) of FA polymerization in the rubbery state.

Plants support numerous microorganisms within their tissues and the rhizosphere, and these microorganisms, known as the microbiota, can influence plant growth and health. Up to 40% of a plant's photosynthetic metabolism may be invested in the rhizosphere. The microbiota is considered an extra genome that can be modulated to meet plant needs. Researchers have identified a set of genes from these microorganisms, known as the microbiome, which can be manipulated to enhance plant growth and health, improve nutrient absorption, reduce the need for chemical fertilizers, increase resistance to pathogens and pests, and increase stress tolerance. In particular, fungi exhibit large genetic and metabolic diversity and are often used to promote plant growth. For example, the fungus Purpureocillum lilacinum has been employed primarily as a biocontrol agent to manage nematodes, but some studies have suggested that it may also promote plant growth by increasing the efficiency of the plant to absorb nutrients from the soil and provide phytohormones to plants. Therefore, the current review aims to summarize the existing literature on the use of this fungus in agriculture as nematodes control and discuss its potential as a plant growth promoter.

Live fuel moisture content (LFMC) influences fire activity at landscape scale and fire behavior in laboratory experiments. However, field evidences linking LFMC to fire behavior are very limited despite numerous field experiments. In the present study, we reanalyze a shrubland fire dataset with a special focus on LFMC to explain this counterintuitive outcome. We found that this controversy might result from three reasons. First, the range of experimental LFMC data was too moist to reveal significant effect with the widespread exponential or power functions. Indeed, LFMC exhibited a strong effect below 100%, but marginal above this threshold, contrary to these functions. Second, we found that the LFMC significance was unlikely when the size of the dataset was smaller than 40. Finally, a complementary analysis suggested that 10 to 15% of random measurement error in variables could lead to an underestimation by 30 % of the LFMC effect. The effect of LFMC in field experiments is thus stronger than previously reported in the range prevailing during the actual French fire season and in accordance with observations at different scales. This highlights the need to improve our understanding of the relationship between LFMC and fire behavior to refine fire danger predictions.

In this paper, we present a comprehensive 4D study of the early stage of plastic deformation in a polycrystalline binary AlLi alloy. The entire microstructure is mapped with X-ray diffraction contrast tomography and a set of bulk grains is further studied via X-ray topotomography during mechanical loading. The observed contrast is analyzed with respect to the slip system activation and the evolution of the orientation spread is measured as a function of applied strain. The experimental observations are augmented by the mechanical response predicted by crystal plasticity finite element simulations to analyze the onset of plasticity in details. Simulation results show a general agreement of the individual slip system activation during loading and that comparison with experiments at the length scale of the grains may be used to fine tune the constitutive model parameters.

This paper presents a requirements specification analysis for driving the design of new systems that will allow 3D media creators to further promote and monetize from their work. The provided requirements analysis is based on the IEEE 830 standard for requirements specification. It allows us to elucidate system requirements through existing (AS-IS) and envisioned (TO-BE) scenarios affected by the latest trends on design methodologies and content promotion in social media. A total of 30 tools for content creation, promotion and monetization are reviewed. The target groups, i.e. creator groups, are divided in 10 types according to their role in 3D media production. Based on this division 10 candidate TO-BE scenarios have been identified and out of these 10 scenarios, we have selected 6 scenarios for validation by media creators. The validation was performed through a survey of 24 statements on a 5 Likert scale by 47 individuals from the domains of Media, Fine arts, Architecture, and Informatics. Useful evaluation results and comments have been collected that can be useful for future systems design.

DEXTER (Detection of EXplosives and firearms to counter TERrorism) is a project funded by NATO’s Science for Peace and Security (SPS) program with the goal of developing an integrated system capable of remotely and accurately detecting explosives and firearms in public places without impeding the flow of pedestrians. The active microwave component of the DEXTER project is referred to as MIC (Microwave Imaging Curtain), supported by the French SGDSN (General Secretariat of Defense and National Security), and utilizes a radar system capable of generating 3D images in real time to address non-checkpoint detection of explosives and fire-arms. The project, led by the ONERA (France), is based on a radar imaging system developed by the Fraunhofer FHR institute, using a MIMO architecture with an Ultra Wide-Band waveform. Although high-resolution 3D microwave imaging is already being used in expensive body scanners to detect firearms concealed under clothing, MIC's innovative approach lies in utilizing a high-resolution 3D imaging device that can detect larger dangerous objects carried by moving individuals at a longer range, in addition to providing discrete detection in pedestrian flow. Automatic detection and classification of these dangerous objects is carried out on 3D radar im-ages using a deep-learning network. This paper will outline the project's objectives and constraints, as well as the design, architecture, and performance of the final system. Additionally, it will present real-time imaging results ob-tained during a live demonstration in a relevant environment.

NaClO3 and NaBrO3 are believed to form a complete solid solution from RT to fusion. The unique solid phase can thus be written: NaClO3 (1-x)-NaBrO3 (x) with: 0 ≤ x ≤ 1. This study shows that at high temperature this statement might be valid. Nevertheless, up to 50°C and probably up to 160°C and even higher temperature, this is not true when the system is in thermodynamic equilibrium. A large miscibility gap exists at room temperature (RT). This gap could be reduced up to a complete disappearance by fast crystallization, for instance by spray-drying. The necessary conditions to access to equilibrium including homochirality are also discussed.

Healthcare systems are mindful of the importance of proper diet and nutrition in reducing the risk of various chronic diseases resulting in hospitalizations. In this regard, they are focusing on promoting the intake of foods comprising various diets with health benefits, such as the ketogenic diet. In this meta-analysis, a total of 20 research studies on the effect of the ketogenic diet on the immune system were analyzed. The research studies were obtained from three databases: Google Scholar, PubMed, and Science Direct. From the meta-analysis, the odd ratio of a similar outcome of an improvement in the strength of immunity between the intervention and control group was 0.76. On the other hand, the p-value for the studies was 0.09, with 15 out of the 20 being considered statistically significant. The heterogeneity between the studies was I2 = 15%, signifying a low variability in the findings that is not by chance. The Ketogenic diet indeed has positive effects on immunity. Nonetheless, it can also result in negative effects that may harm human health.

By taking advantage of a stability criterion established recently, the critical temperature T_c is reckoned with help of the microscopic parameters, characterising the normal and superconducting electrons, namely the independent-electron band structure and a repulsive two-electron force. The emphasis is laid on the sharp T_c dependence upon electron concentration and inter-electron coupling, which might offer a practical route toward higher T_c values and help to understand why high-T_c compounds exhibit such remarkable properties.

The objective of this paper is to investigate the debonding behavior of the interface between continuously and discontinuously fiber reinforced thermoplastics using the climbing drum peel test. The study emphasizes the importance of considering different climatic boundary conditions due to the properties of thermoplastics. Specimens with varying moisture contents are prepared and tested. It is observed that an increase in moisture content initially results in a higher fracture surface energy being required to separate the two materials, but a further increase results in a decrease of the required energy. The study presents an explanatory model of increasing plasticization of the polymer due to increased polymer chain mobility, which results in more deformation energy being required to propagate the crack. The experiment is also modeled numerically for the first time with cohesive surfaces, which successfully reproduces the force-displacement curve in the experiment.

IntroductionThe use of protective masks, especially medical masks, increased dramatically during the COVID-19 crisis. Medical masks are made of synthetic materials, mainly polypropylene, and a majority of them are produced in China and imported to the European market. The urgency of the need has so far prevailed over environmental considerations.ObjectiveAssess the environmental impact of different strategies for the use of facemaskMethod Different strategies for the use of medical and community masks are being investigated for their environmental impact in this study. 8 scenarios, differentiating the typologies of masks and the modes of reuse are compared using several environmental impact indicators, mainly the Global Warming Potential (GWP100), and the plastic leakage (PL). This study attempts to provide clear recommendations that consider both the environmental impact and the protective effectiveness of face masks used in the community.Results The environmental impact of single-use masks is the most unfavorable, with a GWP of 0.4 -1.3 kgCO₂ eq., depending on the transport scenario, and a PL of 1.8 g, for a one month protection against COVID-19. The use of home-made cotton masks and prolonged use of medical masks through wait-and-reuse are the scenarios with the lowest impact.ConclusionThe use of medical masks with a wait and reuse strategy seems to be the most appropriate when considering both environmental impact and effectiveness. Our results also highlight the need to develop procedures and the legal/operational framework to extend the use of protective equipment during a pandemic.

The endophytic fungus Aspergillus sp. SPH2 was isolated from the stems of the endemic plant Bethencourtia palmensis and its extracts were found to have strong fungicidal effects against Botrytis cinerea and ixodicidal effects against Hyalomma lusitanicum at different fermentation times. In this study, the fungus was grown using three different culture media and two methodologies, Microparticulate Enhancement Cultivation (MPEC) and Semi-Solid Fermentation (SSF), to increase the production of secondary metabolites in submerged fermentation. The addition of an inert support to the culture medium (SSF) resulted in a significant increase in extract production. However, when talcum powder was added to different culture media, unexpected results were observed, with a decrease in the production of the biocompounds of interest. Metabolomic analyses showed that the production of aspergillic, neoaspergillic, and neohydroxyaspergillic acids peaked in the first few days of fermentation, with notable differences observed among the methodologies and culture media. Mellein production was particularly affected by the addition of an inert support to the culture medium. These results highlight the importance of surface properties and morphology of spores and mycelia during fermentation by this fungal species.

Tantalum oxide thin films are deposited by DC reactive magnetron sputtering from a tantalum metallic target and oxygen as reactive gas. The reactive gas pulsing process (RGPP) is implemented to produce TaOx compounds with tunable chemical compositions. The argon mass flow rate is maintained constant whereas that of the oxygen gas is pulsed during the deposition. A constant pulsing period T = 10 s is used and the introduction time of the oxygen gas, namely the tON injection time, is systematically changed from 0 to 100 % of the pulsing period T. As the tON injection time increases, the chemical composition of as-deposited TaOx films is continuously changed from pure metallic tantalum to the over-stoichiometric Ta2O5 material. Analysis of the crystallographic structure by X-ray diffraction shows that the films adopt the body-centered cubic structure (metallic Ta) for the lowest tON injection time values (oxygen stoichiometry x &lt; 1.0) and become amorphous for the longest tON injection times. It is shown that the tON injection time is a key parameter to produce either homogeneous tantalum oxides, or periodic Ta/TaOx multilayers with alternations close to 3 nm. Similarly, optical transmittance spectra of the film/glass substrate system are recorded in the visible region and the electrical conductivity of the films is measured vs. temperature. Both exhibit a gradual evolution from metallic (300K = 8.17105 S m-1 with a null optical transmittance in the visible range) to semi-conducting (300K = 1.97103 S m-1 with a semi-transparent behavior) and finally to dielectric properties (300K &lt; 10-5 S m-1 for interferential films) as a function of the oxygen concentration in the films.

Industrial agriculture (IA) is the predominant model of food production since the Green Revolution in the 1950s. IA has been recognized among the main drivers of biodiversity loss, climate change and native pollinator decline. This is controversial, given that native agricultural pollinators are an important resource biota already contributing to crop yield, especially in areas defined as "world biodiversity hotspots” (WBH). These areas often overlap with agricultural zones hosting a significant proportion of cultivated land, mainly through intensive agricultural practices. Pollinator biodiversity and pollination services in these places are currently under threat due to the negative consequences of IA. The dual role of insects as key players allowing the maintenance of the natural ecosystem, as well as main crop pollinators, is particularly exacerbated and urgently requires conservation actions in WBH and food-producing zones. Here we summarize the known negative effects of IA on pollinator biodiversity and illustrate these problems by considering the case of Chile. Food exports represent a considerable part of the economy in this OECD “developing country” in the “Global South”, and a large part of its surface has been highlighted as a unique WBH. This area is currently being replaced by IA businesses at a fast pace, threatening local biodiversity. We present agroecological strategies for sustainable food production and pollinator conservation in food-producing WBHs like Chile. These alternatives recognize native pollinators as internal inputs that cannot be replaced by IA technological packages or external inputs and support the development of agroecological and biodiversity restoration practices to protect their existing biodiversity. We suggest a strategy that integrates four fundamental pillars for producing food in a sustainable way, recognizing biodiversity and local cultural heritage: 1) Share the land, restore and protect; 2) Ecological intensification; 3) Localized knowledge, research and technological development; and 4) Territorial planning and implementation of socio-agroecological policies. We suggest that this approach does not need greater modification of native pollination services that sustain the world with food and basic subsistence goods, but a paradigm change where the interdependency of nature and human wellbeing are recognized for ensuring the present and future of the world’s food security and sovereignty as well as considering the reduction of consumerism and food waste.

Neurodegenerative diseases such as Alzheimer's disease, Parkinson's disease, Huntington's disease, and Amyotrophic Lateral Sclerosis are heterogeneous, progressive diseases with frequently overlapping symptoms characterized by a loss of neurons. Studies suggested relations between neurodegenerative diseases for many years, e.g., regarding the aggregation of toxic proteins or triggering endogenous cell death pathways. Within this study, publicly available genomic, transcriptomic and proteomic data were gathered from 188 studies and more than one million patients to detect shared genetic patterns between the neurodegenerative diseases and the analyzed omics-layers within conditions. The results show a remarkably high number of shared genes between the transcriptomic and proteomic levels for all diseases while showing a significant relation between genomic and proteomic data only in some cases. A set of 139 genes was found to be differentially expressed in several transcriptomic experiments of all four diseases. These 139 genes showed overrepresented GO-Terms and pathways mainly involved in stress response, cell development, cell adhesion, and the cytoskeleton. Furthermore, the overlap of two and three omics-layers per disease were used to search for overrepresented pathways and GO-Terms. Taken together, we could confirm the existence of many relations between Alzheimer's disease, Parkinson's disease, Huntington's disease, and Amyotrophic Lateral Sclerosis on the transcriptomic and proteomic level by analyzing the pathways and GO-Terms arising in these intersections. The significance of the connection between the transcriptomic and proteomic data for all four analyzed neurodegenerative diseases showed that exploring these omics-layers simultaneously holds new insights that do not emerge from analyzing these omics-layers separately. Our data therefore suggests addressing human patients with neurodegenerative diseases as complex biological systems by integrating multiple underlying data sources.

Wall–stabilized arcs dominated by nozzle–ablation are key elements of self–blast circuit breakers. In the present study, high–current arcs were investigated using a model circuit breaker (MCB) in CO2 as gas alternative to SF6 and in addition a long polytetrafluoroethylene nozzle under ambient conditions for stronger ablation. The assets of different methods for optical investigation were demonstrated, e.g. high-speed imaging with channel filters and optical emission spectroscopy. Particularly the phase near current zero (CZ) crossing was studied in two steps. In the first step using high-speed cameras, radial temperature profiles have been determined until 0.4 ms before CZ in the nozzle. Broad temperature profiles with a maximum of 9400 K have been obtained from analysis of fluorine lines. In the second step, the spectroscopic sensitivity was increased using an intensified CCD camera, allowing single-shot measurements until few microseconds before CZ in the MCB. Ionic carbon and atomic oxygen emission were analyzed using absolute intensities and normal maximum. The arc was constricted and the maximum temperature decreased from &gt;18000 K at 0.3 ms to about 11000 K at 0.010 ms before CZ. The arc plasma needs about 0.5-1.0 ms after both the ignition phase and the current zero crossing to be completely dominated by the ablated wall material.

The objective of this work was to investigate the use of remotely sensed vegetation indices to improve the quality of yield maps. The method was applied to the yield data of twelve cornfields from the Data Intensive Farm Management project. The results revealed the need to time shift the yield values up to three seconds to better match the sensor readings with the geographic coordinates. The residuals of the yield prediction model were used to identify points with unlikely yield values for that location, as an alternative to traditional approaches using local spatial statistics, without any assumption of spatial dependence or stationarity. The temporal and spatial distribution of the standardized coefficients for each experimental unit highlighted the presence of trends in the data. At least five out of the twelve fields presented trends that could have been induced by data collection.

Mapping forest composition using multiseasonal optical time series is still challenging. Highly contrasted results are reported from one study to another suggesting that drivers of classification errors are still under-explored. We evaluated the performances of single-year Formosat-2 time series to discriminate tree species in temperate forests in France and investigated how predictions vary statistically and spatially across multiple years. Our objective was to better estimate the impact of spatial autocorrelation in the validation data on measurement accuracy and to understand which drivers in the time series are responsible for classification errors. The experiments were based on ten Formosat-2 image time series irregularly acquired during the seasonal vegetation cycle from 2006 to 2014. Due to lot of clouds in the year 2006, an alternative 2006 time series using only cloud-free images has been added. Thirteen tree species were classified in each single-year dataset based on the SVM algorithm. The performances were assessed using a spatial leave-one-out cross validation (SLOO-CV) strategy, thereby guaranteeing full independence of the validation samples, and compared with standard non-spatial leave-one-out cross-validation (LOO-CV). The results show relatively close statistical performances from one year to the next despite the differences between the annual time series. Good agreements between years were observed in monospecific tree plantations of broadleaf species versus high disparity in other forests composed of different species. A strong positive bias in the accuracy assessment (up to 0.4 of Overall Accuracy) was also found when spatial dependence in the validation data was not removed. Using the SLOO-CV approach, the average OA values per year ranged from 0.48 for 2006 to 0.60 for 2013, which satisfactorily represents the spatial instability of species prediction between years.

MicroRNAs (miRNAs) play important roles in the control of HIV-1 infection. Here, we performed RNAseq profilings of miRNAs and mRNAs expressed in CD4+ T-lymphocytes upon HIV-1 infection. Our results reveal significant alterations of miRNAs and mRNAs expression profiles in infected relative to uninfected cells. One of the miRNAs markedly downregulated in infected cells is miRNA-26a. Among the putative targets of miRNA-26a are CD59 receptor transcripts, which are significantly upregulated in infected CD4+ T-cells. Addition of miRNA-26a mimics to CD4+ T-cells reduces CD59 at both mRNA and surface protein levels, validating CD59 as a miRNA-26a target. Consistent with the reported inhibitory role of CD59 in complement-mediated lysis (CML), knocking-out CD59 in CD4+ T-cells renders both HIV-1 infected cells and progeny virions more prone to antibody-dependent CML (ADCML). Addition of miRNA-26a mimics to infected cells leads to enhanced sensitivity of progeny virions to ADCML, a condition linked to a reduction of CD59 packaging into released virions. Lastly, HIV-1-mediated downregulation of miRNA-26a expression is shown to be dependent on integrated HIV-1 expression but does not involve viral accessory proteins. Overall, these results highlight a novel mechanism by which HIV-1 limits ADCML by upregulating CD59 expression via miRNA-26a downmodulation.

Treatment of osteochondritis dissecans of the knee, has always been a challenge for orthopedic surgeons. We present a case report of a 38-year-old male with severe right knee pain after suffering from an indirect trauma and axial rotation of the knee, limiting knee functionality and impeding ability to walk, with diagnosis of osteochondritis dissecans in the trochlea of the knee, who underwent arthroscopic treatment with matrix induced autologous chondrocyte implantation (MACI). After the surgery, physical therapy protocol for MACI was implemented, magnetic imagen resonance images with cartilage mapping were used to evaluate recovery of the lesion. A total recovery was observed evaluated with the modified Cincinnati knee rating system (mCKRS). A discussion is provided with evidence and general recommendations for the use of MACI in the treatment of adult OCD of the knee.

Articular cartilage injuries are found in up to 60 % of patients who undergo an arthroscopic knee procedure, those that totally affect articular cartilage (grade IV) have limited regenerative capac-ity and extended time for recovery, 3-D scaffolds represent a novel solution to address this type of injury. Our purpose was to analyze MRI findings and functional status of patients that underwent repair of chondral defects either by microfractures or Hyaluronan (HA) 3-D Scaffold. We con-ducted a retrospective study of patients with chondral defects. The outcomes analyzed in this study included anatomical changes envaulted by the Henderson score (based on MRI findings) at baseline, 6, and 12 months after surgery; and improvement in functionality, evaluated by the Modified Cincinnati Knee Rating System (MCKRS) at baseline and 6 months after surgery. Clini-cal and demographic characteristics were similar for both groups. There was a statistically sig-nificant improvement in Henderson score for the 3-D scaffolding treated group at 6 months, ver-sus the microfracture group (p < 0.0001). Improvement in functionality, measured by MCKRS was more frequently found in the 3-D scaffold treated group. In conclusion the use of HA 3-D scaf-folding was superior with faster recovery, evident after 6 months of the surgery, that progress to full recovery in all patients after a year of surgery. Future studies with a randomized design might help to sustain our findings. This study provides a level III of evidence.

The choice of antibiotic regimens to use in patients presenting with diabetic foot osteomyelitis and their duration differs according to the situation. Antibiotics play a more important role in the medical option where no infected bone has been resected while their role is reduced but not negligible in the case of surgical options. Some studies have reported the presence of biofilm structures in bone samples taken from patients with diabetic foot osteomyelitis which raises the question of the place of anti-biofilm antibiotic regimens in this setting. During the last two decades, clinical studies have suggested a potential benefit for anti-biofilm antibiotics, mainly rifampicin against staphylococci and fluoroquinolones against gram-negative bacilli. No data from randomized controlled studies have however been reported so far. The present work provides a summary of the available data on the question of the place of anti-biofilm antibiotics for the treatment of diabetic foot osteomyelitis but also the potential limitations of such treatments.

We propose a silviculture with a purely biological logic that takes soil into account. The article is divided into three parts: 1) presentation of the issue in the context of biodiversity and forest pro-tection; 2) impact of the soil functioning on forestry; 3) possible implementation of soil functioning in forestry practice, to support and protect a non-or minimally anthropized evolution of the forest. The first chapter illustrates the importance of the forest for the future of the planet and our human species, referring to recently published works on the topic of climate warming and biodiversity. The second illustrates the aspects that link soil dynamics to the silvogenetic cycle, focusing on the humipedon (organic and organo-mineral surface horizons, approximately the first 30 cm of forest soil), and more significant carbon storage in old forests since up to 2/3 is found in the soil. In the third chapter we consider the possibility of lengthening the forestry cycle, to allow the return of nutrients to the soil. Theoretical graphs and distribution models of the number of trees as a func-tion of diameter and age are reported, with examples of logging in uneven Alpine forests, with reference to Swiss fir-beech forests published on the Pro-Silva website.

The severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) is an emerging infectious disease with currently a pandemic state. Cardiac function can be involved, affecting prognosis, in addition with lung feature severity, particularly in patients with comorbidities. Since the renin angiotensin aldosterone (RAA) system may interact with SARS-Cov-2, researches are still ongoing to assess the prognostic value of RAA blockers in cardiology.