In this research the possibility of using pH change to measure proton conductivity of proton exchange membranes (PEM) or else known as polymer electrolyte membranes are tested with using an experimental setup prepared by using pH meters. PEMs are an important part of the fuel cells and proton conductivity of the PEMs are one of the most important properties of the PEMs. Also, proton conductivity is the one of the biggest limiting factors of fuel cells thus it is important to measure the proton conductivity of the PEMs while trying new polymers or new types of membranes. But as current measurement methods do not have a standard and can be separated into mainly two different measurement methods which are Electron Impedance Spectroscopy (EIS) and Ion Exchange Capacity (IEC). EIS gives clearer results, but it needs an impedance analyzer machine, platinum electrodes and setup so this cannot be possible for every researcher due to its economical aspect. For IEC it is basically a titration method to see acid groups in the polymer or polymer matrix which are directly responsible for proton conductivity so this can show an indirect measurement of proton conductivity. But as for this one drawback are firstly this one is an indirect measurement and secondly needs overnight bath in solution can take long times. So, the possibility of using pH can be easier and both from time and economical aspect if it can be proven the give a direct relationship between pH change and proton conductivity.

Magnetic force microscopy (MFM) is a widespread technique for imaging magnetic structures with a resolution of some 10 nanometers. MFM can be calibrated to obtain quantitative (qMFM) spatially resolved magnetization data in units of A/m by determining the calibrated point spread function of the instrument, its instrument calibration function (ICF), from a measurement of a well-known reference sample. Beyond quantifying the MFM data, a deconvolution of the MFM image data with the ICF also corrects the smearing caused by the finite width of the MFM tip stray field distribution. However, the quality of the calibration depends critically on the calculability of the magnetization distribution of the reference sample. Here, we discuss a Ti/Pt/Co multilayer stack which shows a stripe domain pattern as a suitable reference material. A precise control of the fabrication process combined with a characterization of the sample micromagnetic parameters allows to reliably calculate the sample’s magnetic stray field, proven by a very good agreement between micromagnetic simulations and qMFM measurements. A calibrated qMFM measurement using the Ti/Pt/Co stack as a reference sample is shown and validated and the application area for quantitative MFM measurements calibrated with the Ti/Pt/Co stack is discussed.

The social criteria of sustainable development have remained underexplored. Moreover, a large number of green building assessment tool and social sustainability documentations have been developed which, has had a direct impact on social criteria issues, but there seems to be a substantial gap in the study of social criteria in green building assessment tools. In examining the problem facing social sustainability, taking into consideration social sustainability in sustainable development reviews and green building assessment tool towards social aspects. This paper through analysis identified a centripetal conceptual framework composed of seven key components equity, education, participation & control, social cohesion, health & safety, accessibility & satisfaction, and cultural values. The interpretation of the social sustainability in green building assessment tool would impact building practitioners towards implementing social criteria in GBAT. The aim was to identify social categories as well as consider a starting point for the development of an effective social criteria assessment tool for green building.

This study introduces a comparative analysis of two deep learning (multilayer perceptron neural networks (MLP-NN) and the long short term memory networks (LSTMN)) models for transit travel time prediction. The two models were trained and tested using one-year worth of data for a bus route in Blacksburg, Virginia. In this study, the travel time was predicted between each two successive stations to all the model to be extended to include bus dwell times. Additionally, two additional models were developed for each category (MLP of LSTM): one for only segments including controlled intersections (controlled segments) and another for segments with no control devices along them (uncontrolled segments). The results show that the LSTM models outperform the MLP models with a RMSE of 17.69 sec compared to 18.81 sec. When splitting the data into controlled and uncontrolled segments, the RMSE values reduced to 17.33 sec for the controlled segments and 4.28 sec for the uncontrolled segments when applying the LSTM model. Whereas, the RMSE values were 19.39 sec for the controlled segments and 4.67 sec for the uncontrolled segments when applying the MLP model. These results demonstrate that the uncertainty in traffic conditions introduced by traffic control devices has a significant impact on travel time predictions. Nonetheless, the results demonstrate that the LSTMN is a promising tool that can has the ability to account for the temporal correlation within the data. The developed models are also promising tools for reasonable travel time predictions in transit applications.

Evidence shows how food system activities from production to consumption underpin food security. However, studies exploring climate impacts on food security in northern Ghana have overly focused on production systems, neglecting post-production activities that loom large in food security. This paper addresses the research need to comprehensively analyze how climate change affects post-production activities and exacerbates food insecurity risks in northern Ghana. The study collects and analyzes data on climate hazards, impacts, and food system vulnerabilities using questionnaires and participatory engagement with farming households in northern Ghana. Results show that climate-induced food insecurity risks in northern Ghana are not just products of persistent climate impacts on food production in the region. Instead, risks are inextricably connected to the vulnerability contexts within which food is harvested, processed, stored, and marketed. Specifically, the results reveal that climate hazard events such as floods, extreme temperatures, and droughts damage stored grain, disrupt food supply to the market, and cause seasonal volatilities in food prices. However, these impacts are not solely externally generated circumstances. The food system is highly vulnerable; most households lack access to threshing and grinding machines, warehouse storage, post-harvest management information, and transportation services. These underlying characteristics of the post-food-production system of northern Ghana, which is ultimately quite remote from climate change, exacerbate household-level food insecurity risks.

Melatonin is an important hormone with a methoxy-indole structure. It is secreted regularly by the pineal gland of mammals. It takes part in many chemical, biological, and physiological activities of the body. Melatonin, acts as a basic hormone, and is responsible for circadian rhythm regulation and sleep control. It has been shown to occur in the highest concentration in organisms during the night times. In living organisms, many activities that have physiological, biological, hormonal, and psychological characteristics follows a certain rhythm. Body temperature, hormone levels, sleep-wakefulness, and some other cognitive functions in humans also change with the circadian rhythm. Its synthesis and release begin with darkness and end with light. This review aims to explore the functions of melatonin such as its stimulating effects on antioxidant enzymes, reducing lipid peroxidation, and protecting brain tissue from oxidative damage. It also has properties that stop the proliferation of cancer cells and prevent tumor growth. Melatonin, which was previously known only as an animal hormone, has been found to also exist in plants. Research has shown that melatonin is present in almost all plant species analyzed to date and that it performs functions similar to those in animals. In plants, it plays a vital role in dealing with various abiotic and biotic stresses. Melatonin acts as an important antioxidant in post-harvest technology and extends the post-harvest life of fruits and vegetables. It also takes part in the regulation of stress-specific genes and the activation of pathogenesis-related proteins and antioxidant enzymes. The most prominent roles of melatonin in plants include regulating circadian rhythm, growth, and development, and increasing tolerance to a wide range of environmental stress factors. The review reveals the effects of melatonin as an extremely important secondary metabolite, on human, animal, and plant metabolism. The use of PRISMA guidelines was used for reporting, search, selection, and synthesis. Information up to 2024 was searched from search engines for the occurrence, nature and function of melatonin. Key words such as structural function, hormonal function, secretion and metabolism were used in the search of publications.

AI applications are transforming the technology and digital sector, seamlessly integrating into the daily interactions of individuals with the digital world. Key entry points to the internet, such as search engines, are now complemented by recommendation systems that curate content on social networks, streaming platforms, and online marketplaces. Additionally, virtual assistants have become ubiquitous across various platforms. While these groundbreaking changes are gradually extending to several industries, there remains significant untapped potential for the application of artificial intelligence in diverse domains. The renewable energy sector, in particular, continually reinvents itself through research and innovation to meet the escalating demand. Positioned at the forefront of technological evolution, this industry is well-placed to effectively adopt and tailor the innovations of artificial intelligence to its specific needs. Presently, both emerging and established tools leverage elements of AI to enhance processes and introduce functionalities that were previously unattainable. If the current trajectory persists, AI-enhanced tools have the potential to assume a role as crucial to the future of engineering as computer-aided design (CAD) software is in contemporary times.

Introduction: Parents’ behavior and practices affect many aspects of family life, including health, and many studies have proven that children's bad habits are associated with parents’ behavior and practices. Objectives: This study aimed to identify parents’ negative behaviors that might affect their families’ health and social development. Methodology: A descriptive cross-sectional study was conducted to examine the influence of parents’ behavior and practices on their family health, in which 192 respondents participated. Results: The results clarified the influence of parents on family health in several aspects. On the behavioral side, approximately 90% of the participants agreed that the behavior of parents may affect the behavior of their families, and the social and educational side results clarified the relationship between parents' illiteracy and support for the cognitive and social health of the family. Discussion: This study clarified that there is a significant relationship between illiterate parents and their ability to support their families, illustrating that the majority of participants thought that the development of the cognitive and social health of families depends on the presence of supportive parents, which has many implications for family social and psychological health. Conclusion: Parental behaviors and practices have a strong effect on their family’s health, which affects the development of the families’ cognitive and social health. Recommendation: The study recommends the need for supportive, friendly hospitals for family social health and the provision of specialized programs that support the family’s social and psychological health.

The paper presents a thorough examination of the burgeoning field of utilizing manufacturing waste for sustainable energy generation, aligning with the global imperative for resource efficiency and clean energy solutions. With the manufacturing sector being a significant contributor to waste generation, this study explores innovative approaches to transform waste materials into valuable resources, thereby mitigating environmental impacts and contributing to a circular economy. This work critically reviews current trends, emphasizing technological advancements, policy interventions, and market dynamics shaping the manufacturing waste utilization landscape. Noteworthy developments, such as advanced sorting technologies and the integration of digital solutions, are discussed in detail, showcasing their role in enhancing the efficiency of waste management processes. The study outlines future trends in the field, anticipating a shift towards closed-loop systems guided by circular economy principles. This comprehensive review aims to contribute to the discourse on sustainable waste management and energy generation by providing a holistic perspective on the field's current state and offering insights into the future trajectories that will propel manufacturing waste toward a more sustainable and circular future. The synthesis of technological innovation, collaborative efforts, and evolving regulatory frameworks presents a compelling case for the continued exploration of manufacturing waste as a valuable resource in the pursuit of a more sustainable and energy-efficient world.

Advancements in deep learning and availability of medical imaging data have led to use of CNN based architectures in disease diagnostic assisted systems. In spite of the abundant use of reverse transcription-polymerase chain reaction (RT-PCR) based tests in COVID-19 diagnosis, CT images offer an applicable supplement with its high sensitivity rates. Here, we study classification of COVID-19 pneumonia (CP) and non-COVID-19 pneumonia (NCP) in chest CT scans using efficient deep learning methods to be readily implemented by any hospital. We report our deep network framework design that encompasses Convolutional Neural Networks (CNNs) and bidirectional Long Short Term Memory (biLSTM) architectures. Our study achieved high specificity (CP: 98.3%, NCP: 96.2% Healthy: 89.3%) and high sensitivity (CP: 84.0%, NCP: 93.9% Healthy: 94.9%) in classifying COVID-19 pneumonia, non-COVID-19 pneumonia and healthy patients. Next, we provide visual explanations for the CNN predictions with gradient-weighted class activation mapping (Grad-CAM). The results provided a model explainability by showing that Ground Glass Opacities (GGO), indicators of COVID-19 pneumonia disease, were captured by our CNN network. Finally, we have implemented our approach in three hospitals proving its compatibility and efficiency.

Among various processes, catalytic CO2 methanation has emerged as a promising method for carbon capture and utilization. Therefore, a CO2 methanation reaction studied with experimentally. The extent of coke formation on the catalyst after the reaction was quantitatively studied. Then, four different machine learning model were employed in order to model CO2 methanation process and to predict CO2, CO, CH4, H2 and N2 concentrations at outlet. The results of the machine learning models were consistent with the experimental data. Performances of the proposed regression methods are evaluated with 10-fold cross validation. Random forest and decision tree regression performed the best among other methods by achieving R >0.98 for the output concentrations and were able to outperform other modeling approaches. It was shown that the best result among the literature studies is reached in this study. The results have demonstrated the possibility of simulation of the methanation process via machine learning techniques. These techniques can be used control and optimization of carbon capture.

In recent years, online learning has become one of the most popular methods of educational delivery due to advances in technology, which has been made even more evident in the COVID-19 lockdown period. Online education has evolved into a distinct field of study within the educational system over the last few years. It is also important to note that parallel with the growth in this field, there has also been an increase in the number of scholarly journals that regularly publish research in this field, reflecting the importance of this field in the modern day. In spite of the fact that online learning offers a wide range of educational options, from short courses to full-time degrees, as well as being accessible, flexible, environmentally friendly, and affordable, there are also certain challenges associated with this educational approach. These challenges include the lack of social interaction, technical errors, a lack of hands-on training, and difficulties in assessing students. It is, therefore, imperative to ask the crucial question of whether online learning can replace traditional classroom learning or whether it can supplement it in hybrid models with it, as well as what factors and conditions are likely to determine this in the short- and long-term, as well as how it will be blended together in the future. The purpose of this commentary is to provide a brief summary of the current status of both learning models, as well as their pros and cons, in order to answer the question that was posed above.

This paper investigates the influence of microorganisms and clay minerals on the deterioration process of ancient Egyptian murals in the Al-Qurna region, situated on the west bank of Thebes (Luxor), Egypt. To achieve this objective, an extensive examination of building materials (including bedrock, building stone, mortars, and plasters) from various tombs within the study area was conducted. The investigation employed a multidisciplinary approach, combining micro-biological analysis with advanced techniques such as X-ray diffraction (XRD), X-ray fluorescence (XRF), scanning electron microscopy with energy dispersive spectroscopy (SEM-EDS) as well as petrographic examination. These methods were employed to identify the composition of the materials and to assess the masonry structure’s response to deformation caused by endogenous factors, particularly clay minerals. Additionally, mycological analyses were performed using a swabbing cotton sterile technique, revealing the presence of several species, including Ascosphera apis, Aspergillus tamarii, Aspergillus ochraceus, Doratomyces sp, and Eurotium repens. Notably, swelling clays—such as smectite, illite, and chlorite—along with mixed layers of illite-smectite and illite-vermiculite were detected in the studied samples. The presence of such deleterious clay minerals and fungi imperils wall painting preservation, causing discoloration, surface alteration, physical decay, and structural instability. Informed conservation strategies must address these threats for sustained integrity.

Serious outbreaks of foodborne disease have been caused by Listeria monocytogenes found in retail delicatessens and the severity of disease is significant, with high hospitalization and mortality rates. Little is understood about the formidable public health threat of L. monocytogenesin all four niches, humans, animals, food and environment in Egypt. This study analyzed the presence of L. monocytogenes collected from the four environmental niches and bioinformatic analysis was implemented to analyze and compare the data. PCR was used to detect virulence genes encoded by pathogenicity island (LIPI-1). prfA amino acid substation that causes constitutive expression of virulence was common in 77.7% of isolates. BLAST analysis did not match other isolates in the NCBI database suggesting this may be a characteristic of the region associated with these isolates. A second group included the NH1 isolate originating in China, and BLAST analysis showed this prfA allele was shared with isolates from other global locations such as Europe and North America. Identification of possible links and transmission pathways between the four niches, helps to decrease the risk of disease in humans, to take more specific control measures in the context of disease prevention, to limit economic losses associated with food recalls and highlightens the need to treatment options.

A typical orchard's mechanical operation consists of three or four stages: lining, digging for plantation, moving the seedling from nurseries to the farm, moving the seedling to the planting hole, and planting the seedling in the hole. However, the digging the planting hole is the most time-consuming operation. In fruit orchards, robots' usage is increasingly becoming more prevalent to increase operational efficiency. They offer practical and effective services to both industry and people, whether they are assigned to plant trees, reduce the use of chemical fertilizers, or carry heavy loads to relieve staff. Robots can operate for extended periods of time and can highly adept at repetitive tasks like planting many trees. The present study aims to identify the locations for planting trees in orchards using geographic information systems (GIS), to develop an autonomous drilling machine and use the developed robot to open planting holes. There isn't a comparable study on autonomous hole planting in the literature in this regard. The agricultural mobile robot is a four wheeled nonholonomic robot with differential steering and forwarding capability to stable target positions. The designed mobile robot can be used in fully autonomous, partially autonomous, or fully manual modes. The drilling system, which is a y-axis shifter driven by a DC motor with reducer includes an auger with a 2.1 HP gasoline engine. SOLIDWORKS software was used for designing and drawing of the mobile robot and drilling system. The Microsoft Visual Basic.NET programming language was used to create the robot navigation system and drilling mechanism software. The cross-track error (XTE), which determines the distances between the actual and desired holes positions, was utilized to analyze the steering accuracy of the mobile robot to the drilling spots. Consequently, the average of the arithmetic means was determined to be 4.35 cm, and the standard deviation was 1.73 cm. This figure indicates that the suggested system is effective for drilling plant holes in orchards.

Cholesterol is a lipid-derived substance found in lipoproteins and cell membranes. It is also one of the main sources for the production of bile acids, vitamin D, and steroid hormones. Today, foods are evaluated by consumers not only according to their taste and nutritional content but also according to their effects on consumer health. For example, many consumers choose foods according to their cholesterol level. The cholesterol in the food can directly affect the blood cholesterol level when consumed, which can lead to cardiovascular diseases. High levels of cholesterol can lead to diet-related human diseases such as cardiac arrest, paralysis, type II diabetes cerebral hemorrhage. In societies with high living standards, interest in and consumption of foods that lower or have low cholesterol levels have increased recently. Accordingly, efforts to increase the variety of foods with reduced cholesterol levels are on the rise. This has indirectly insulted in accurate measurement of cholesterol levels in blood and food being of great importance. Classical chemical, enzymatic, colorimetric, polarographic, chromatographic, spectrophotometric methods, and enzymatic, nonenzymatic, and electrochemical sensors and biosensors are used for the determination of cholesterol in foods. The purpose of this review is to reveal and explore current and future trends in cholesterol detection methods in foods. The review will summarize the most appropriate and standard methods for measuring cholesterol in biological components and foods.

The increasing demand for water resources in urban areas, such as Bangladesh, due to population growth is a significant concern. One potential solution under consideration is the use of air conditioning (AC) condensate water. A study conducted at the European University of Bangladesh (EUB) focused on assessing the quality and quantity of AC condensate water from various systems. The results indicate that the collected water generally adhered to the quality standards established for drinking and household use in Bangladesh. Parameters such as pH (averaging 6.8), turbidity (1.08 NTU), total dissolved solids (TDS) (averaging 219 mg/L), iron content (0 mg/L), alkalinity (averaging 41.67 mg/L), arsenic (0 mg/L), chemical oxygen demand (COD) (averaging 3.67 mg/L), biochemical oxygen demand (BOD) (averaging 1.33 mg/L), chloride content (averaging 30.77 mg/L), and other factors were evaluated. Moreover, the AC units at EUB, varying in cooling capacity (1 ton, 2 tons, and 4 tons), produced substantial monthly volumes of 96, 177, and 354 liters of condensate water, respectively. This underscores the potential of AC condensate water as a valuable resource for addressing urban water scarcity. As a result, there is a pressing need for local decision-makers and policymakers to establish well-defined guidelines for the effective utilization of AC condensate water to mitigate water scarcity issues in urban areas.

Due to the host immunological disease brought on by infection is sepsis, multiple organ dysfunction syndrome (MODS), which has a high morbidity and mortality rate, could be the result. With advances in pathogen detection technologies, breakthroughs in anti-infection drugs, and the creation of organ function support, the clinical diagnosis and treatment of sepsis have advanced significantly. Pathogen-induced abnormal immunological responses, which can range from excessive inflammation to immunosuppression, are recognized to play a significant role in the high death rate. Unfortunately, no medications that are specifically intended to treat sepsis have been licensed. In order to offer a theoretical foundation for the management of sepsis, we will now discuss current advancements in research on immunological responses in sepsis. The prognosis of sepsis patients may be improved by developing and optimizing a dynamic immune system treatment plan based on anti-infection therapy, fluid replacement, support for organ function, and timely application of immunomodulatory therapies

This study addresses an alternative use of viscous dampers (VDs) associated with buckling restrained braces (BRBs) as the innovative seismic protection devices. For this, 4, 8 and 12 storey steel frames were designed with 6.5 m equal span length and 4 m storey height. Thereafter, the VDs and BRBs were placed over the height of each frame considering three different configurations. The structures were modeled using SAP2000 finite element program and evaluated by the nonlinear time history analyses subjected to the six natural accelerograms (1976 Gazlı, 1978 Tabas, 1987 Superstition Hills, 1992 Cape Mendocino, 1994 Northridge and 1999 Chi-Chi). The structural response of the structures with and without VDs and BRBs were studied in terms of variation in the displacement, interstorey drift, absolute acceleration, maximum base shear, time history of roof displacement. The results clearly indicated that the application of VDs and BRBs had remarkable improvement in the earthquake performance of the case study frames by reducing the local/global deformations in the main structural systems and satisfied the serviceability.

The production of lycopene from different substrates by Blakeslea trispora in fermentation was investigated. Lycopene productions from 4 and 6 % glucose (pH 6.5) in shake flask fermentation were 77.7 and 28.1 mg L-1. A maximum lycopene concentration of 944.8 mg L-1 was detected with 4 % glucose supplemented with 1.0 % sunflower oil in fermentor studies. Zygospores of B. trispora are the morphological forms, which are responsible for the production of the lycopene. The highest level of zygospores was correlated with the highest amount of intracellular lycopene in the total biomass dry weight. The media containing only orange peel (1 %) gave a 4.9 mg L-1 lycopene production in a fermentor. The presence of oils as substrates resulted in enhanced mold growth and subsequent higher lycopene production. Substrates containing linoleic acid compounds led to high lycopene production. The data showed that the biosynthesis of lycopene starts in most cases simultaneously in the early growth phase even in trace amounts and the amount of lycopene formation increased continuously from 2 to 7 days.

In this paper, the effects of biodiesel on performance and emission of the current and new-coming regulation cycles, namely the New European Driving Cycle (NEDC) and the Worldwide Harmonized Light Vehicles Test Cycle (WLTC), were investigated by conducting tests on a passenger car, Euro-5 Ford Fiesta, equipped with a 1.5-liter diesel engine. In a two-axle chassis dynamometer test bed, NEDC and WLTC were performed with pure diesel and biodiesel-to-diesel blend (30% biodiesel, 70% diesel in volume). A substantial reduction in CO, HC, and PN emissions was observed for both the NEDC and WLTC when biodiesel was used. Besides, it was found that the WLTC has higher load and velocity profile compared to the NEDC. Moreover, lower CO, HC, and PN emissions were observed with B30 fuel under WLTC compared to the NEDC. Nevertheless, slightly higher CO2 and substantially higher NOx emissions were observed for the WLTC compared to the NEDC.

Antimicrobial edible coatings could eliminate pathogen contamination risk on the surface of meat and poultry products during storage. In this study, the edible coating (EC) based on wheat gluten, Pistacia vera L. tree resin (PVR), and essential oil (EO) of PVR were applied on chicken breast fillets (CBF) by dipping method to prevent the growth of Salmonella Typhimurium and Listeria monocytogenes. The samples were packed in foam trays wrapped with low-density polyethylene stretch film and stored at 8°C for 12 days to observe antimicrobial effects and sensory properties. The total bacteria count (TBC), L. monocytogenes, and S. Typhimurium were reported during the storage. All samples coated with EC containing 0.5, 1, 1.5, and 2% v/v EO (ECEO) decreased microbial growth significantly compared to control samples. The growth of TBC, L. monocytogenes, and S. Typhimurium was suppressed by 4.6, 3.2, and 1.6 logs, respectively, at the end of 12 days on the samples coated by ECEO (2%) compared to uncoated controls (p<0.05). Coating with ECEO (2%) also preserved appearance, smell, and general acceptance parameters better than uncoated raw chicken (p<0.05) on the 5th day of storage. In grilled chicken samples, ECEO (2%) did not significantly change the sensory properties of appearance, smell, and texture but had increased taste and general acceptance scores (p>0.05). So, ECEO (2%) can be a feasible and reliable alternative to preserve chicken breast fillets without affecting their sensory properties adversely during the shelf life.

This analysis focuses on identifying the most efficient and cost-effective method of supplying power to a remote site, exploring photovoltaics (PV) and small wind turbines as primary power sources, and evaluating battery banks and hydrogen storage fuel cell systems as potential storage options. The hydrogen storage system converts surplus renewable power into hydrogen through an elec-trolyzer, storing it for later use in a fuel cell when renewable sources produce less power, enabling efficient energy storage during peak production periods. A sensitivity analysis of wind speed and hydrogen subsystem cost was conducted to evaluate the hydrogen storage system's performance. The optimal system graph suggests that the hydrogen subsystem must significantly decrease in cost to rival the battery bank, and in most cases, both the hydrogen system and battery bank were recommended together, offering reliable and efficient power for the remote site. While the battery bank is presently the more feasible option for powering the remote site, continuous monitoring and evaluation of both systems, considering site location, energy needs, and available resources, are essential to determine the most suitable power supply approach as technology advances and costs evolve over time.

Abstract Introduction There is a clear link between self-medication practice and ongoing pandemic diseases like COVID-19, According to studies conducted globally and the general Ethiopian population turned to self-medication and symptomatic treatment as a result of inadequate COVID-19 treatment and also about 80% of the population amassed drugs for pandemic use. Objective: The objective of this study was to assess self-medication practice for treatment of Covid-19 and reason to use self- medication among residents in Bedelle city and its surrounding, Southwest Oromia, Ethiopia. Methodology: A cross sectional study design was employed and the standardized questionnaire was developed by reviewing relevant literatures then the data was collected using face to face interview. Final data was analyzed by using SPSS version 23. Result: The final study contained 415 respondents in total, with a response rate of 98.5%. The majority of responses were females and between the ages of 18 - 25 Category. In this study population, the use of self-medication since the onset of the Covid-19 epidemic was reported by participants were around 50.6%. Analgesics (42.4%) and cold medicines (29.5%) were the most frequently used medications for treatment of COVID-19. Also the reported uses of these drugs included treatment of Covid-19 symptoms like the Headache (22.2%), Fever (13.2%), respiratory infective (14.3%), and cold (21.4%) were the most frequently reported symptoms for self-medication. Self-medication methods were used more frequently by women than Men. Conclusion: According to this study, analgesics and cold medications are commonly self- medicated drugs used for Covid-19 therapy. It is a serious health concern, particularly when COVID-19 symptoms are present, and high consumption of self-medication has been linked to COVID-19 prevention or treatment. Key words: Covid-19, Medicine, Practice, Bedelle city, Self-Medication

Background: World Health Organization (WHO) estimates that there were 558000 new cases with resistance to Rifampicin, of which 82% had multidrug-resistant tuberculosis (MDR-TB). Objectives: We aimed to identify the prevalence of MDR-TB in River Nile state, Sudan, and the risk factors contributing to its occurrence. Methods: This was a descriptive cross-sectional hospital-based study involved 200 specimens taken from patients suspected of having MDR-TB tested using an automated GeneXpert assay. Results: Results of GeneXpert assay showed that the presence of Mycobacterium tuberculosis in 81 (40.5%), and out of 81 positive test results there were 13 (16%) had MDR-TB. Additionally, 7 cases of MDR-TB were previously treated which represented about (53%) of MDR patients, the remaining 6 MDR-TB patients were new cases and represented (47%) of MDR-TB patients. Moreover, there were 4 MDR-TB patients who had a history of contact with MDR-TB patients. Conclusion: Prevalence of MDR-TB in River Nile State, Sudan was 16%, which is greater than WHO estimation for Sudan (10.1%). The results revealed that the main risk factor to develop MDR-TB was a history of contact with MDR-TB, so adherence to treatment and social awareness about the spread of MDR-TB are crucial preventive measures.

The effect of casein savinase hydrolysate (CSH) usage on frozen dough (1%, 1.5% and 2%, g/100 g flour) was investigated in terms of rheological, thermal, structural characteristics of wheat doughs and the textural and color properties of corresponding breads. Rheological measurement showed that CSH addition into dough led to a reduction of Gʹ and Gʹʹ values, but a similar trend wasn’t observed in frozen dough samples. The increase of protein band intensity was observed for control dough (CD) after frozen storage (-30 °C, 28 days) while there was no increases in band intensities of the doughs with CSH. The freezable water content of unfrozen doughs was decreased gradually with addition of CSH depended on concentration level. Frozen storage caused a notable reduction in α-helices structure of CD sample (p<0.05) while no significant variation was observed for the doughs containing CSH (p>0.05). Lowest specific volume reduction and hardness increment were observed for the breads containing 1.5% and 2% CSH. Frozen storage caused a significant reduction on b* value of bread crust (p<0.05) while no significant effect was observed for L* and a* value during frozen storage (p > 0.05). Overall, CSH incorporation into frozen dough can be an alternative that could reduce the quality deteriorations of frozen bread.

The aim of this study was to examine brightness effect, which is the perceptual property of visual stimuli, on brain responses obtained during visual processing of these stimuli. For this purpose, brain responses of the brain to changes in brightness were explored comparatively using different emotional images (pleasant, unpleasant and neutral) with different luminance levels. Moreover, electroencephalography recordings from 12 different electrode sites of 31 healthy participants were used. The power spectra obtained from the analysis of the recordings using short time Fourier transform were analyzed, and a statistical analysis was performed on features extracted from these power spectra. Statistical findings obtained from electrophysiological data were compared with those obtained from behavioral data. The results showed that the brightness of visual stimuli affected the power of brain responses depending on frequency, time and location. According to the statistically verified findings, the distinctive effect of brightness occurred in the parietal and occipital regions for all the three types of stimuli. Accordingly, the increase in the brightness of pleasant and neutral images increased the average power of responses in the parietal and occipital regions whereas the increase in the brightness of unpleasant images decreased the average power of responses in these regions. However, the increase in brightness for all the three types of stimuli reduced the average power of frontal and central region responses (except for 100-300 ms time window for unpleasant stimuli). The statistical results obtained for unpleasant images were found to be in accordance with the behavioral data. The results also revealed that the brightness of visual stimuli could be represented by changing the activity power of the brain cortex. The main contribution of this research was to comprehensively examine brightness effect on brain activity for images with different emotional content and different frequency bands at different time windows of visual processing for different brain regions. The findings emphasized that the brightness of visual stimuli should be viewed as an important parameter in studies using emotional image techniques such as image classification, emotion evaluation and neuro-marketing.

Pseudomonas aeruginosa (P. aeruginosa) produces a suite of virulence factors that are coordinated by Quorum Sensing (QS) contributing to its disease-causing ability in aquaculture. The present study is first of its kind to obtain information regarding the presence and distribution of five QS genes, three virulence genes viz: lasI, lasR, rhlI, rhlR, rhlAB, toxA, aprA and plcH and seven of the Extended-spectrum βlactamases (blaVEB, blaPER, blaTEM,, blaSHV, blaCTX-M1, blaCTX-M2 and blaCTX-M3) of Pseudomonas species isolated from fish meat by direct PCR. Bacterial identification was based mainly on conventional biochemical techniques using the Vitek 2, automated system. Phenotypic sensitivity of antibiotics was established by the agar disc diffusion technique through 16 various antimicrobial drugs. Quantification of their in vitro production of numerous virulence genes outside the cell that are QS dependent namely, pyocyanin, elastase, alkaline protease, biofilm and cytotoxicity of Vero cell was as well executed. Fifteen genes demonstrated an enormous variety in their association. The total number of Pseudomonas species isolates were 30/100 to be identified by the API 20NE system as P. aeruginosa 12/30 (40%), P. fluorescens 8/30 (27%), P. putida 6/30 (20%) and P. alkylphenolia 4/30 (13%). The outcomes of this study have great significance for the strategic designation of QS quenching.

While there are well-known synthetic methods in the literature to find the image of a point under circular inversion in l2−normed geometry (Euclidean geometry), there is no similar synthetic method in Minkowski geometry, also known as the geometry of finite-dimensional Banach spaces. In this study, we have succeeded in giving a synthetic construction for the circular inversion in l1−normed spaces, which is one of the most fundamental examples of Minkowski geometry. Moreover, this synthetic construction has been given using the Euclidean circle, independently of the l1−norm.

Solar photovoltaic (PV) technology is a cornerstone of the global effort to transition towards cleaner and more sustainable energy systems. This paper explores the pivotal role of PV technology in re-ducing greenhouse gas emissions and combatting the pressing issue of climate change. At the heart of its efficacy lies the efficiency of PV materials, which dictates the extent to which sunlight is transformed into electricity. Over the last decade, substantial advancements in PV efficiency have propelled the widespread adoption of solar PV technology on a global scale. The efficiency of PV materials is a critical factor, determining how effectively sunlight is transformed into electricity. Enhanced efficiency, achieved through a decade of progress, has driven the global expansion of solar PV. Multi-junction photovoltaic materials have now exceeded 40% efficiency in lab tests. China leads the world in solar PV installations, boasting over 253 GW of installed capacity by the end of 2021. Other prominent countries in this sector are the United States, Japan, Germany, and India. Supportive policies like feed-in tariffs, net metering, tax incentives, and cost reductions in PV modules have made solar PV increasingly competitive against fossil fuel-based power generation. Solar PV technology holds immense potential for creating a cleaner, reliable, scalable, and cost-effective electricity system. To expedite its deployment and foster a more sustainable energy future, continued investment in research and development, along with supportive policies and market mechanisms, is essential. This paper underscores the pivotal role of solar PV technology in the global energy transition and advocates for a concerted effort to unlock its full potential in achieving a more sustainable and resilient energy future.

The majority of skin cancers are caused by over exposure to ultraviolet (UV) radiation. The effects of UV radiation on the expression of drug transporters expressed in human skin has never been studied. In this the effects of UVA and UVB irradiation on the expression of ATP-binding cassette (ABC) transporters and Solute carrier (SLC) transporters was evaluated in normal human epidermal keratinocytes (NHEK) and normal human dermal fibroblasts (NHDF) in primary culture. First experiments were intended to validate the inflammatory reaction in response to stimulation by lipopolysaccharide (LPS) in NHEK, NHDF and 3D-reconstructed human epidermis (3D-RHE) model. LPS treatment has shown to increase the expression of IL-8 and TNF-alpha in all three in vitro models. Expression of the most expressed ABC and SLC transporters was then measured in NHEK and NHDF after UVA (30 J/m²) and UVB (40 mJ/m²) irradiation. The most striking result was a significant 29-fold increase of the expression of SLCO4A1 in normal human dermal fibroblasts. In summary, this study shows for the first time a significant regulation of the expression of SLCO4A1 in human dermal fibroblasts induced by UVA irradiation. This finding is of particular interest as most of skin cancers are caused by over exposure to ultraviolet radiation and need to be considered in pharmacokinetic evaluation of topical drugs.

Acacia nubica is well-adapted to harsh conditions and offers valued socio-economic and environmental benefits. This research studied seed germination and seedling growth of A. nubica in vitro in response to the application of different concentrations of sodium hypochlorite, sucrose, and Murashige and Skoog (MS) medium. The synchrony, percentage, and rate of germination of A. nubica seed were studied. Seedling development was assessed by measuring the shoot, root, and number of nodes. Sodium hypochlorite at 10% produced the maximum germination percentage, while 5% induced a faster and more uniform emergence. Sucrose has various effects on seed emergence and germination depending on the concentrations; 30 g/L elicited the highest germination, while 10 g/L improved seed emergence rate with higher uniformity. The highest seed germination was achieved on ¼-MS medium, although 0-MS strength recorded faster and more synchronized germination. The development of A. nubica seedlings was influenced by MS medium strengths and sucrose concentrations. Full MS medium produced the highest shoot length and the highest vigor index with the addition of 20 g/L sucrose and the maximum root length with 50 g/L sucrose. Also, 30 g/L sucrose gave the maximum number of nodes and the maximum root/shoot ratio. However, ½-MS strength yields the highest seedling biomass with 30 g/L sucrose. This is the first successful report on the seed germination and seedling growth of A. nubica in vitro.

Transient global amnesia (TGA) is an uncommon clinical syndrome characterized by a loss of short-term memory and disorientation that resolves in twenty-four hours. The etiology is unknown and the diagnosis is made by exclusion of other possible etiologies that may cause similar patterns and the reversibility of the condition in less than 24 hours. Here we report a 60-year-old male presented with sudden onset of disorientation and short-term memory loss early in the morning while at home and started to ask his whereabouts and what happened. He had no history of significant medical or psychiatric disease. There was no history of previous similar episodes. He had no recent history of sleep problems, head trauma, substance abuse, or loss of consciousness. He had no history of seizure disorder, or migraine. A neurologic examination revealed a normal wakefulness state with mild disorientation, and short-term memory impairment. He had score of 18/30 on mini-mental state examination (which later returned to normal baseline in 24 hours). Extensive lab investigations did not show any abnormal findings. Brain MRI did not show any acute cerebral pathology. The EEG was negative for any abnormal cerebral activity. His memory improved and returned to normal baseline over the course of a 20-hour from the onset. After exclusion of potential causes and the patient returned to normal state of memory, the diagnosis of transient global amnesia was made. At the follow-up visit, the patient was in a state of normal function without a recurrence of memory impairment. Here we presented this interesting case of transient global amnesia. TGA is diagnosis of exclusion and important to keep in mind when evaluating a patient with acute onset of short-term memory impairment, especially when etiological investigation revealed no potential cause.

With recent focus on deep neural network architectures for development of algorithms for computer-aided diagnosis (CAD), we provide a review of studies within the last 3 years (2015-2017) reported in selected top journals and conferences. 29 studies that met our inclusion criteria were reviewed to identify trends in this field and to inform future development. Studies have focused mostly on cancer-related diseases within internal medicine while diseases within gender-/age-focused fields like gynaecology/pediatrics have not received much focus. All reviewed studies employed image datasets, mostly sourced from publicly available databases (55.2%) and few based on data from human subjects (31%) and non-medical datasets (13.8%), while CNN architecture was employed in most (70%) of the studies. Confirmation of the effect of data manipulation on quality of output and adoption of multi-class rather than binary classification also require more focus. Future studies should leverage collaborations with medical experts to aid future with actual clinical testing with reporting based on some generally applicable index to enable comparison. Our next steps on plans for CAD development for osteoarthritis (OA), with plans to consider multi-class classification and comparison across deep learning approaches and unsupervised architectures were also highlighted.

Pulsed thermography is a vital technique in the nondestructive evaluation field. However, its data analysis can be complex and requires skilled experts. Advances in deep learning have yielded exceptional results, including image segmentation. Therefore, many efforts have been made to apply deep learning methods to data processing for nondestructive evaluation. Despite this, there is currently no public Pulsed thermographic dataset available for evaluating various spatial-temporal deep methods of segmenting pulsed thermographic data. This article aims to provide such a dataset and assess the performance of commonly used deep learning-based instance segmentation models on it. Additionally, the impact of the number of frames and data transformations on model performance is examined. The findings suggest that suitable preprocessing methods can effectively reduce the data size without compromising the deep models’ performance.

Vaccination against Newcastle disease (ND), a devastating viral disease of chicken, is often hampered by thermal inactivation of the live vaccines, in particular in tropical and hot climate conditions. In the past “thermostable” vaccine strains (I-2) have been proposed to overcome this problem. In the current study, we compared the thermal stability of 6 commercially available ND vaccines. Subjected to 37°C as lyophilized preparation, two vaccines containing I-2 strains were more sensitive to inactivation than a third I-2 vaccine or when compared to three other vaccines based on different strains. However, after reconstitution strains proved to have a comparable tenacity. Interestingly, all vaccines retained a sufficient virus dose for protection (106 EID50) after 1 day at 37°C, still. However, experiments exposing ND-vaccines to elevated temperatures of 51°C and 61°C, clearly demonstrated inactivation of all dissolved vaccines within 2 to 4 hours. The data indicate preparation that specific factors may influence thermal stability rather than strain specific characteristics. Regardless of the ND strain used, the appropriate cold chain is mandatory for live ND-vaccines.

This work aims to explore the impact of side loads, drill-pipe tool-joint (DP-TJ) speed (RPM), and mud type on the austenitic stainless steel SM2535-110 casing wear characteristics. Actual field drill pipe tool joints, casings, and drilling muds are used in this study. The results of the study show that under both types of lubrication, the wear volume increased with radial load and DP-TJ speed. SM2535-110 casing specimens tested under oil-based mud (OBM) lubrication had higher casing wear volumes than those obtained under water-based mud (WBM) lubrication. This unexpected behavior is mainly due to the increase in the surface hardness of the casing specimens tested under WBM. The results also show that the specific wear factor (K) values of specimens tested under WBM are in general 2 to 4 times higher than those obtained under OBM. While K values under WBM increase with both the side load and RPM, those under OBM show a sharp decrease with RPM. This behavior under OBM is due to this lubricant’s higher viscosity and the change of lubrication regime from thin film to thick film lubrication at higher RPM. Scanning electron microscopy (SEM) and the digital microscopic imaging (DMI) of SM235-110 casing specimens show that an aggressive combination of adhesive, abrasive, and plastic deformation was observed under WBM, while the dominant wear mechanism under OBM is abrasive wear.

Otolith morphology analysis is one of the main tools used for fish or fish stock identification. Moreover, otolith shape can also be used in fish dietary studies (stomach content) for the identi-fication of prey fishes and their size according to the relationship between fish and otolith sizes. In the present study, the relationship between fish length and otolith morphological dimensions was investigated for the sabre squirrelfish, Sargocentron spiniferum (Forsskål, 1775) (family: Hol-ocentridae). Samples of 185 fish were collected from the coast of the Red Sea, Egypt. To analyze the relationship between fish and otolith, otolith morphometric measurements (length, width, area, perimeter, weight, sulcus, and ostium) and shape factors (aspect ratio, compactness, form factor, rectangularity, roundness, ellipticity, squareness) describing outline shape were extracted using image analysis. Generalized linear models were applied for the relationship between body length and each otolith morphology feature. From the relationships between the total length of fish and fourteen morphology features, only otolith length, caudal length, and squareness were significantly correlated with fish size. Our results provide more information for the relationship between fish length and otolith morphometric features.

The design of torsional springs for Series Elastic Actuators (SEAs) is challenging, especially when it comes to balancing good stiffness characteristics and efficient torque robustness. This study focuses on the design of a lightweight, low-cost, and compact torsional spring for use in rotary series elastic actuator (ES-RSEA) of lumbar support exoskeleton. The exoskeleton is used as an assistive device to prevent lower back injuries. The torsion spring was designed following design for manufacturability (DFM) principles, focusing on minimal space and weight. The design process consisted of determining the potential topology and optimizing the selected topology parameters through finite element method (FEM) to reduce equivalent stress. The prototype was made using a waterjet cutting process with low-cost material (AISI-4140-alloy) and tested using a custom-made test rig. The results showed that the torsion spring had a linear torque-displacement relationship with 99% linearity, and the deviation between FEM simulation and experimental measurements was less than 2%. The torsion spring has a maximum torque capacity of 45.7 Nm and a stiffness of 440 Nm/rad. The proposed torsion spring is a promising option for lumbar support exoskeletons and similar applications requiring high stiffness, low weight-to-torque ratio, and cost-effectiveness.

The effects of the surface waves generated by the wind have a significant effect on the currents. A wave current coupled model plays an important role in the design of offshore structures. The interaction between fluids such as incompressible ocean waves and current and offshore structures is significant with many real-time applications in offshore engineering. These coupled models can be applied to Offshore Floating Production Operating and offloading (FPSO), Wind or current turbines and offshore pipelines. The complex issues related to the design are analyzed by using Computational Fluid Dynamics, which requires an investigation of the multiphase flow between wave and current and the structure which is considered restrictive due to the computational cost. If viscous effects are neglected then the single-phase flow models have been recommended, where wave-current interaction have been modelled successfully. Models have been developed where velocities and pressure are computed and the results can be verified with the experimental results available in the literature. In this study the existing numerical methods, mesh types are discussed along with their coupling methods. Here single-phase and multiphase models with small and medium movement are reviewed and their applications are highlighted.

One of the major steps toward the industrialization of microbial product(s) is to optimize the cultivation conditions at the large scale bioreactor and successfully control the microbial behavior within large scale production environment. Statistical Design of Experiment was proven to optimize a vast number of microbial processes to achieve robustness and explore possible interactions among the variables. In this research, Taguchi Orthogonal Array was applied to optimize the cultivation condition of a newly isolated Prodigiosin-producing marine bacterial strain, Serratia AM8887, at bioreactor level. Two steps fermentation process was applied; as the productivity was scaled up from shake flask level to a bench top bioreactor (5L) and subsequently to an in-situ sterilization bioreactor system (20L) leading to a yield of 7g/L compared to 100mg/L prior to optimization confirming that; applying Taguchi experimental design is a reliable and good positive option for the optimization of biotechnological processes.. The produced pigment was purified and the chemical structure was revealed by means of Spectrophotometric, Maas Spectrum (MS), Fourier transform infrared (FT-IR), and proton nuclear magnetic resonance (1H-NMR) spectroscopy analysis. The biological activity including antibacterial, antioxidants and cytotoxicity to cancer cells line of the pigment were explored. The pigment showed very characteristic features that could helpful in food, pharmaceuticals and/or textile industries.

The paper concludes that the choice of charging strategy depends on the specific requirements and limitations of the off-grid solar PV system, and that a careful analysis of the factors that affect performance is necessary to identify the most appropriate approach. Also provides valuable insights for designing and optimizing off-grid solar PV systems, which can help to improve the efficiency, reliability, and cost-effectiveness of these systems.

Otolith morphology analysis is one of the main tools used for fish or fish stock identification. Moreover, otolith shape can also be used in fish dietary studies (stomach content) for the identification of prey fishes and their size according to the relationship between fish and otolith sizes. In the present study, the relationship between fish length and otolith morphological dimensions was investigated for the sabre squirrelfish, Sargocentron spiniferum (Forsskål, 1775) (family: Holocentridae). Samples of 185 fish were collected from the coast of the Red Sea, Egypt. To analyze the relationship between fish and otolith, otolith morphometric measurements (length, width, area, perimeter, weight, sulcus, and ostium) and shape factors (aspect ratio, compactness, form factor, rectangularity, roundness, ellipticity, squareness) describing outline shape were extracted using image analysis. Generalized linear models were applied for the relationship between body length and each otolith morphology feature. From the relationships between the total length of fish and fourteen morphology features, only otolith length, caudal length, and squareness were significantly correlated with fish size. Our results provide more information for the relationship between fish length and otolith morphometric features.

Microgrids (MGs) have evolved as critical components of modern energy distribution networks, providing increased dependability, efficiency, and sustainability. Effective control strategies are essential for optimising MG operation and maintaining stability in the face of changing environmental and load conditions. Traditional rule-based control systems are extensively used due to their interpretability and simplicity. However, these strategies frequently lack the flexibility for complex and changing system dynamics. This paper provides a novel method called hybrid intelligent control for adaptive MG that integrates basic rule-based-control and deep learning techniques, including gated recurrent units (GRU), basic recurrent neural network (RNN) and long short-term memory (LSTM). The main target of this hybrid approach is to improve MG management performance by combining the strengths of basic rule-based systems and deep learning techniques. These deep learning techniques readily enhance and adapt control decisions based on historical data and domain-specific rules, leading to increasing system efficiency, stability, and resilience in adaptive MG. Our results show that the proposed method optimises MG operation, especially under demanding conditions such as variable renewable energy supply and unanticipated load fluctuations. This study investigates special RNN architectures and hyper-parameter optimization techniques with the aim of predicting power consumption and generation within the adaptive MG system. Our promising results show the highest-performing models indicating high accuracy and efficiency in power prediction. The finest-performing model accomplishes an R2 value close to 1, representing a strong correlation between predicted and actual power values.

Rice varieties such as Mahsuri Mutan and Basmati 370 are categorized as specialty rice with kernel elongation ratio exceeding 1.6 and 2.0, respectively. Ageing treatment in rice could affect the physical and chemical properties of rice such as grain size and shape, quality and taste of the cooked rice. The main objective of this study was to determine the effects of ageing treatment on the physicochemical properties of Mahsuri Mutan, Basmati 370 and MR219 rice varieties. The three rice varieties were subjected to heat treatment at 90ºC using the oven for 3 hours. After the heat treatment, the samples were cooled at room temperature (25ºC) for 1 hour. Physicochemical properties such as alkali digestion value, water uptake ratio (WUR), solids in cooking water (SCW), high kernel elongation (HKE) ratio and amylose contents were determined. Data collected on physicochemical traits and ageing vs non-ageing treatments were subjected to analysis of variance (ANOVA) using SAS software version 9.4. Phenotypic correlation coefficient indicated that there was a high positive correlation between HKE and water uptake ratio. The ageing treatment also showed significant difference in all the physicochemical traits of the varieties studied. Observation under electron microscope showed that the ageing samples had more cracks on the tissue structure compared to normal rice samples. The hexagon structure in Mahsuri Mutan gave more elongation effect on its kernel. The findings from this study could be useful to breeders in selection and development of new high kernel elongation rice variety.

Mpox, formerly known as Monkeypox, is a rare viral disease initially discovered in Africa in 1958. Since its first identification, several outbreaks have occurred in various African nations. Recently, the global community has witnessed a resurgence in the number of Mpox cases reported worldwide, prompting the World Health Organization (WHO) to declare the ongoing multi-country outbreak a public health emergency in July 2022. This study reports on the first cases of Mpox detected in Khartoum State, Sudan, outlining the epidemiology, preparedness, and public health response to this new challenge. A total of 55 suspected cases were identified, with two confirmed cases. The clinical manifestations observed in these cases align with the classic skin rash typical of Mpox, presenting alongside symptoms like fever, headache, and joint pain. The findings underscore the need for heightened surveillance, early detection, and timely intervention to prevent the domestic spread of Mpox and its potential impact on public health. Continued global efforts are needed to support effective screening, diagnostic, and control measures, ultimately enhancing preparedness and response in the face of this emerging disease.

A recent breakthrough in preparation of immobilized enzyme based biocatalysts achieving highly enhanced enzymatic activities and stabilities has become a great alternative to conventional immobilization techniques. The functional hybrid nanobiocatalysts (FHNs) fabricated in this immobilization composed of organic components (amino acid, peptide, protein, enzyme and plant extract) and inorganic components (various metal ions) give flower-like morphology with narrow size distribution and porous structure. The enzyme incorporated FHNs exhibite greatly enhanced catalytic activities and stabilities compared to free and conventionally immobilized enzymes under various experimental conditions. In addition to that, the FHNs consisting of other organic components act as Fenton-like reagents and show peroxidase-like activity owing to presence of metal ions and porous structure in the FHNs. This report basically focuses on preparation, characterization, and bioanalytical applications of the FHNs and explain mechanism of the FHNs formation and thier enhanced activities and stabilities.

Cryptosporidiosis is one of the most important causes of gastroenteritis in the world, especially in low- and middle-income countries. It is caused by the Apicomplexan parasite Cryptosporidium spp., and mainly affects children and immunosuppressed people, in whom it can pose a serious risk to their health, or even be life-threatening. In Honduras there are no data on parasite species or on molecular diversity or Cryptosporidium subtypes. Therefore, a cross-sectional study was conducted between September 2019 and March 2020 for the molecular identification of Cryptosporidium spp. in 102 patients living with HIV who attended a national hospital in Tegucigalpa. Stool samples were analysed by direct microscopy, acid-fast stained smears, and a rapid lateral flow immunochromatographic test. All samples that tested positive were molecularly analyzed to identify the species and subtype of the parasite using three different markers: gp60, cowp, and 18Sr. PCR products were also sequenced. Four out of 102 samples (3.92%) were positive for Cryptosporidium parvum, and all were assigned to subtype IIa. These findings suggest a possible zoonotic transmission in this population.

This paper is about to estimate the suspended sediment transport amount in the streams flowing into the Sapanca Lake Basin. There are 12 subsidiary streams flowing into the Sapanca Lake Basin. With the aim of estimating the suspended sediment transport in 2012-204 in these subsidiary streams, measurements belonging the parameters such as level, cross sectioning, flow rate, temperature and suspended sediment were made monthly. Along the measurement period, weather conditions were above seasonal normal and precipitations decreased. In order to estimate the suspended sediment amount by using results of the measurement obtained, Artificial Neuron Network (ANN), Sediment Rating Curve (SRC) and Multiple Linear Regression (MLR) models were used for different scenarios. It was seen that artificial neuron networks yielded the most accurate results among the models.

Background: Metformin is a drug used to treat patients with type 2 diabetes, especially those who suffer from obesity. It is also used in the treatment of women with polycystic ovary syndrome (PCOS). This disease has been shown to be related to insulin resistance and multiplied blood sugar ranges. Further, it has been found that the use of metformin improves the menstrual cycles and ovulation rates of these women. Methods: A structured questionnaire will be conducted to determine the prevalence of breast cancer among women using metformin in the Ha’il region. Result: Incidence of breast cancer among women using metformin in the Ha’il region is very low. Conclusions: According to previous findings, metformin has been linked to lower breast cancer risk in women with type 2 diabetes. Furthermore, the findings of this study have corroborated the literature for the same by indicating that there is a substantial connection between metformin use and a lower risk of breast cancer in women with type 2 diabetes

The utilization of solar energy technology is crucial for generating hydrogen in sustainable energy systems. While traditional methods involving natural gas, coal, and oil have been employed for hydrogen production, this study aims to explore environmentally friendly techniques. Green hy-drogen, despite being a more expensive option compared to fossil fuel-derived hydrogen, has prompted engineers to develop affordable and low-carbon technologies. The microgrid model was developed to showcase a self-contained DC islanded system designed to supply power to an electrolyzer, capitalizing on both a solar array and an energy storage unit. This comprehensive model offers a versatile platform for evaluating the operational dynamics involved in the sustainable production of green hydrogen. Over a span of seven days, it permits the as-sessment of hydrogen generation characteristics through the utilization of solar energy, either di-rectly from a solar array or through an integrated system that incorporates energy storage. The model encompasses a multi-domain framework, encompassing electrical, thermal liquid, and thermal gas aspects, facilitating a holistic exploration of the intricate processes underlying the green hydrogen production system. Through this simulation, the feasibility and efficiency of harnessing renewable energy sources for hydrogen production in an off-grid setting can be comprehensively examined and optimized, contributing to the advancement of sustainable energy solutions.

Corporate identity has played a vital role in the Halal industry to create a strong foundation for its reputation in the long run. This paper used two modeling analyses for two different data. The first analysis aims to predict the relationship between Corporate Identity Management between Internal Brand and Employee Brand Support (consequence) mediated by CIM using partial-least squares-structural equation modeling (PLS-SEM). A total of 206 employees from Malaysia’s Halal food SMEs took part in the survey. The second analysis to identify topic proportions patterns using the topic modeling approach on Halal brand identity Machine learning approach of knowledge mining was applied for this analysis. Metadata of 1,091 articles were mined from the Scopus database on Halal studies across all social sciences fields. The result revealed that there was a partial relationship between Internal Brand (antecedent) and Employee Brand Support (consequence) mediated by CIM. This finding was supported by the identified topic proportions patterns from the topic modeling approach that pointed out a weak topic proportion on the Halal brand identity discussion globally, interestingly the result also found that the Halal brand identity discussion involving the Halal food industry is almost non-existed in Malaysia’s Halal food SMEs. The contributions of this paper were apparent in three major areas which are methodology, theoretical and future suggestions. The utilization of two different model analyses was able to confirm the consistency of the major findings with the literature review which opens up more possibilities for future researchers.

Heat shock transcription factors (HSFs) participate in regulating many environmental stress responses and biological processes in plants. Maize (Zea mays L.) is a major cash crop that is grown worldwide. However, the growth and yield of maize are affected by several adverse environmental inputs. Therefore, investigating the factors that regulate maize growth and development and resistance to abiotic stress is an essential task for developing stress-resilient maize varieties. Thus, a comprehensive genome-wide identification analysis was performed to identify HSFs in the maize genome. The current study identified 25 ZmHSFs, randomly distributed throughout the maize genome. Phylogenetic analysis revealed that ZmHSFs are divided into three classes and 13 sub-classes. Gene structure and protein motif analysis supported the results obtained through the phylogenetic analysis. Domain analysis showed the DNA-binding domain to be the most conserved region of ZmHSFs. Segmental duplication is shown to be responsible for the expansion of ZmHSFs. Most of the ZmHSFs are localized inside the nucleus, and the ZmHSFs which belong to the same group show similar physio-chemical properties. The 3D structures revealed comparable conserved ZmHSFs protein structures. RNA-seq analysis revealed a major role of class A HSFs including, ZmHSFA-1a and ZmHSFA-2a in all the maize growth stages, i.e., seed, vegetative, and reproductive development. Furthermore, ZmHSFs displayed an obvious spatiotemporal expression. Under abiotic stress conditions (heat, drought, cold, UV, and salinity), members of class A and B ZmHSFs are induced. Gene ontology (GO) annotation analysis indicated a major role of ZmHSFs in resistance to environmental stress and regulation of primary metabolism. Further, the protein-protein interaction analysis showed that ZmHSFs interact with several molecular chaperons and major stress-responsive proteins. To summarize, this study provides novel insights for functional studies on the ZmHSFs in maize breeding programs.

Lumbar support exoskeletons with active and passive actuators are currently the cutting-edge technology for preventing back injuries in workers while lifting heavy objects. However, many challenges still exist in both types of exoskeletons, including rigid actuators, risks of human-robot interaction, high battery consumption, bulky design, and limited assistance. In this paper, the design of a compact, lightweight energy storage device combined with rotary series elastic (ES-RSEA) is proposed for use in a lumbar support exoskeleton to increase the level of assistance and exploit the human bioenergy during the two stages of the lifting task. ES takes the responsibility to store and release passive mechanical energy while RSEA provides excellent compliance and prevents injury from the human body's undesired movement. The experimental tests on the spiral spring showed excellent linear characteristics (above 99%) with an actual spring stiffness of 9.96 Nm/rad. The results demonstrate that ES-RSEA can provide maximum torque assistance in the ascent phase with 66.6 Nm while generating nearly 21 Nm of spring torque during descent without turning on the DC motor. Ultimately, the proposed design can maximize the energy storage of human energy, exploit the biomechanics of lifting tasks, and reduce the burden on human effort to perform lifting tasks.

This study investigated the chemical composition, and total phenolic content(TPC), total flavonoid content (TFC), and antioxidant activity Reziz date pomace extracted using different solvent system. The recovery, bioaccessibility, and stability of bioactive compounds were evaluated using In vitro gastrointestinal digestion. The results showed that pomace rich source of fiber but low in fat, and protein. Extraction data revealed that methanol, and ethanol were the most effective solvent for TPC and TFC extraction with higher antioxidant activity. In vitro gastrointestinal digestibility significantly affected recovery, bio-accessibility and stability of bioactive compounds. The TPC, TFC, and antioxidant activities were significantly increased after the mouth digestion but decreased during the gastric and intestinal digestion. The bioaccessibility of polyphenol and flavonoid were 35.22% and 23.57% respectively after the intestinal digestion. The chyme insoluble fraction (pellet) showed higher bioactive compounds and antioxidant activity compared to the chyme soluble fraction. The high fiber content of the date pomace seemed to affect the bioaccessibility of the bioactive compounds. TPC or TFC and the antioxidant activity determined by DPPH and ABTS were found to have a positive correlation with the oral, gastric, and intestinal digestion. The GC-MS analysis of digested date pomace in mouth, gastric, or intestinal digestion revealed an increase in the number of peaks (compounds) compared to the undigested sample. According to these findings, Ruzeiz date pomace could be utilized as a bioactive ingredient source in formulation of functional foods to promote healthy life.

: Dacarbazine, DAC, 5-(3,3-dimethyltriazeno)imidazol-4-carboxamideis is an imidazole-carboxamide derivative, that is structurally related to purines. DAC belongs to the triazene compounds, which are a group of alkylating agents with antitumour and mutagenic properties. DAC is a non-cell cycle specific drug, active on all phases of cellular cycle. In the frame of this work the 3d-metal complexes (cobalt and copper) with dacarbazine were synthesized. Their spectroscopic properties by the use of FT-IR, FT-Raman and 1HNMR were studied. The structures of dacarbazine and its complexes with copper(II) and cobalt(II) were calculated using DFT methods. The effect of metals on the electronic charge distribution of dacarbazine was discussed on the basis of calculated NBO atomic charges. The reactivity of metal complexes in relation to ligand alone was estimated on the basis of calculated energy of HOMO and LUMO orbitals. The aromaticity of imidazole ring in dacarbazine and the complexes was compared (on the basis of calculated geometric indices of aromaticity). Thermal stability of the investigated 3d-metal complexes with dacarbazine and the products of their thermal decomposition were analyzed.

The European Green Deal is the policy established by the EU against global environmental problems. However, it is closely concerned with the countries carrying import and export activities with the EU. Because it is planned to impose an obligation to declare greenhouse gas emission inventories of products imported into the EU, the EU will soon begin to assess the CBAM on imports from carbon-intensive industries. This regulation is expected to affect Turkey-EU trade relations. One of the industries that Turkey has export relations with the EU is the building materials industry. For this reason, it will have had necessary to provide sustainability criteria for the export of building materials. However, there is no database in Turkey where the inventory data of building materials is declared. In Turkey, within the scope of EU Green Deal action plans, it is aimed to create different structures for environmental information of building materials in the medium and long term. In light of such information, within the scope of this study it is aimed to create reference information for building material databases to be developed in Turkey. The study recommends weight and normalization reference values following the life cycle assessment methodology defined by ISO 14040 and ISO 14044 international standards. Twelve environmental impact categories accepted in the literature, including greenhouse gas emissions, have been considered as the environmental impacts of building materials. Semi-structured interviews were held with twenty-one industry stakeholders in Tur-key to determine the weight reference values. The results obtained from the semi-structured interviews were combined using the AHP method. An extensive research study was conducted on Turkey’s national inventory data to determine normalization reference values. Environmental impact calculations were carried out for different building materials in a case study to present the importance of regional adaptation of the determined reference values. The recommended reference information may be used in greenhouse gas emission declarations under the EU Green Deal and other potential environmental impact declarations from building materials.

The load cell is an indispensable component of many engineering machinery and industrial automation for measuring and sensing force and torque. This paper describes the design and analysis of the strain gauge load cell, from the conceptional design stage to shape optimization (based on the finite element method (FEM) technique) and calibration, providing ample load capacity with low-cost material (aluminum 6061) and highly accurate force measurement. The amplifier circuit of the half Wheatstone bridge configuration with two strain gauges has been implemented experimentally with an actual load cell prototype. The calibration test was conducted to evaluate the load cell characteristics and derive the governing equation for sensing the unknown load depending on the measured output voltage. The measured sensitivity of the load cell is approximately 15 mV/N and 446.8 µV/V at a maximum applied load of 30 kg. The findings are supported by FEM results and experiments with an acceptable percentage of errors, which revealed an overall error of 6% in the worst situation. Therefore, the proposed load cell meets the design considerations for axial force measurement for the laboratory test bench, which has a light weight of 20 g and a maximum axial force capacity of 300 N with good sensor characteristics.

Background: Millions of people worldwide suffer from a genetic hemoglobinopathy known as sickle cell disease (SCD). It is a long-term condition marked by progressive multiorgan failure. Among SCD patients, cardiovascular complications are the main leading cause of death. Cardiovascular complication raises cardiac markers level as well as sickle cell vaso-occlusive crisis (VOC). This makes it challenging to determine the source. Methods: This research aims to identify the association between cardiac markers and myocardial infarction in SCD patients At King Abdulaziz University (KAUH) in Jeddah, Saudi Arabia. This retrospective study was conducted from June 2022 to March 2023. All patients with SCD who were 18 years and above were enrolled. Cardiac markers' associations with age, emergency room visits, ECG, blood transfusion, hydroxyurea, anticoagulants, and mortality were analyzed. Result: 537 patient records were screened during the study period, of which 270 met the inclusion criteria. Among these, 144 (53.3%) were female. The prevalence of elevated LDH, troponin, and CK-MB among the SCD patients who visited ER for the VOC was 78.5%, 9.3%, and 6.3%, respectively. Overall, there was a significant relationship between the cardiac marker level and the number of ER visits, age and mortality (p= 0.01), but there was no significant association between the cardiac marker level and for each of the following: hydroxyurea use, antiplatelet/anticoagulant use, needing of blood transfusion and ECG abnormalities. This retrospective research shed light on the significance of cardiac marker levels in patients with SCD. The level of cardiac markers was remarkably linked with age, frequency of ER visits, and patients' states.

Measles is a highly contagious airborne disease that is endemic in many developing countries with low levels of vaccination coverage. In this paper, we propose a deterministic compartmental mathematical model for measles disease dynamics. We establish the global stability conditions for the disease-free and endemic equilibria using the Lyapunov function stability method. \textcolor{red}{Using arbitrary parameters it is obtained that the proposed model exhibits forward bifurcation}. Numerical integration using MATLAB software was used to simulate the model solution of the forward problem. We calibrate the proposed model to estimate the parameters with a 95\% confidence interval (CI) using real data from Ethiopia by formulating an inverse problem. We notice that the model fits well with the real data of Ethiopia. The estimated basic reproduction number ($R_0$) is found to be $R_0=1.3973$ which proves that the disease is endemic. It is also obtained from the local sensitivity analysis that reducing the transmission rate and increasing the vaccination rate could effectively minimize the $R_0$.

Detection of partial discharge (PD) activities in high-voltage equipment can be done according to the several mechanisms of signal detection, which are electromagnetic wave signal detection, acoustic signal detection, chemical reactions, electrical signal detection, or optical emission detection. Recently, multiple methods of detection and localization of partial discharge activities occurred in power transformers and gas-insulated switchgear (GIS) have been proposed to monitor the health condition of high-voltage equipment, especially when the awareness regarding preventive maintenance has been emphasized at the industrial level and electrical providers. In aligning the needs of industrial and the improvement of PD detection methods, this manuscript focused on reviewing the current practice methods for the detection and localization of PD signals in high-voltage equipment and comparing their efficacy, in summarizing the future direction of research work-related methods of PD detection. The comparative reviews are discussed in terms of the mechanism of PD signal detection, indication parameters, calibration technique, advantages, and limitations of each method of PD measurement in detail.

Polyaniline or PANI is a conductive polymer (CPs) with flexibility in turning into conducting properties. The drawback is mainly in terms of limited mechanical properties improvement which attracted the interest in fabrication of PANI with other polymeric materials. PANI-PVL composites film was synthesized and fabricated in this work with chronological steps according to the objectives aligned in two different phases. The first phase determines the optimum parameters to synthesize nanosized PANI. The ideal initial molar ratio, r was 1, stirring speed of 600 rpm, purified by filtration, synthesis temperature of 25 oC, washed by dopant acid, acetone and distilled water. The usage of non-ionic surfactant, Triton X-100 (TX100) with 0.1 % concentration favours the formation of smaller particle size of PANI and good dispersibility compared to the usage of anionic sodium dodecyl sulphate (SDS). The synthesis of PANI in nanosized dimension has the potential to be applied for antimicrobial applications such as gloves and antimicrobial coating of frequent contact points in the near future.

Multidisciplinary research efforts on potential COVID-19 vaccine and therapeutic candidates have increased since the pandemic outbreak of SARS-CoV-2 in 2019. This search has become imperative due to the increasing emergences and limited widely available medicines. The presence of bioactive anti-SARS-CoV-2 molecules was examined from various plant sources. Among them is a group of proteins called lectins that can bind carbohydrate moieties. In this article, we present ten novel, chitin-specific Hevein-like lectins that were derived from Selaginella moellendorffii v1.0's genome. The capacity of these lectin homologs to bind with the spike protein of SARS-CoV-2 was examined. Using the HDOCK server, 3D-modeled Hevein-domains were docked to the spike protein's receptor binding domain (RBD). The Smo446851, Smo125663, and Smo99732 interacted with Asn343-located complex N-glycan and RBD residues, respectively, with binding free energies of -17.5, -13.0, and -26.5 Kcal/mol. The normal-state analyses via torsional coordinate association for the Smo99732-RBD complex using iMODS is characterized by overall higher stability and minimum deformity than the other lectin complexes. The three lectins interacting with carbohydrates were docked against five individual mutations that frequently occur in major SARS-CoV-2 variants. These were in the spike protein’s receptor-binding motif (RBM), while Smo125663 and Smo99732 only interacted with the spike glycoprotein in a protein-protein manner. The precursors for the Hevein-like homologs underwent additional characterization and their expressional profile in different tissues was studied. These in-silico findings offered potential lectin candidates targeting key N-glycan sites crucial to the virus's virulence and infection.

Duchenne muscular dystrophy (DMD) is the most prevalent progressive muscular dystrophy, and the guidelines recommend the regular assessment of respiratory muscle function. This study aimed to assess the relationship between maximum inspiratory pressure (MIP), maximum expiratory pressure (MEP) and sniff nasal inspiratory pressure (SNIP) measurements and upright-supine spirometry parameters in children with DMD, predictability of upright-supine spirometry in terms of diaphragm involvement, and impact of nutrition on muscle strength. This prospective cross-sectional study examined patients with DMD by comparing upright and supine FVC, MIP, MEP, and SNIP measurements. Forty-four patients were included in the study. The mean patient age was 10.8±2.9 years. Twenty-five patients were ambulatory. A significant decrease in FVC, FEV1, and FEF25-75 values was detected in the supine position in both ambulatory and nonambulatory patients (p<0.05). All patients had low MIP, MEP, and SNIP measurements (less than 60 cm H2O). MIP, MEP, and SNIP values were significantly lower in patients with malnutrition than in those without (p<0.05). To accurately assess respiratory muscle strength, supine FVC should be combined with upright FVC, MIP, MEP, and SNIP measurements. It is crucial to regularly screen patients for malnutrition, as this can significantly affect respiratory muscle function during pulmonology follow-up.

In the realm of smart manufacturing, equipment plays a pivotal role, impacting the efficiency and quality of production. Ensuring equipment availability and optimal performance is crucial, necessitating effective maintenance strategies. This paper addresses the complexities of smart device maintenance, which often involves collaboration between multiple entities like device owners, manufacturers, suppliers, and external maintenance services. To enhance this cooperative maintenance, we propose a novel maintenance system based on permissioned blockchain technology, offering superior security and reliability compared to conventional cloud-based platforms. Our contributions include developing an integrated maintenance system framework for smart manufacturing, which facilitates interactions among diverse stakeholders. Additionally, we have developed a prototype of this maintenance system, serving as a practical model for real-world application. Our research primarily demonstrates the practicality and advantages of using permissioned blockchain for maintenance systems in the manufacturing sector, paving the way for more secure, efficient, and collaborative maintenance practices.

Abstract: Gastroesophageal reflux disease (GERD), the inflammatory bowel disease (IBD), and mental health issues are significant public health concerns in globally. Although rising peaks observed post-COVID-19, there is a sever paucity in high quality data. Using descriptive analysis, we identified the frequency and associations of age- and gender, sport, genetic, and psychiatric consequences in the coexistence of GERD and IBD in 2067 participants 18 to >60 years with mean age of 26.8 ± 12.9 years. Most were 18 -29 years old (66%, n=1364) of which majority were young Saudi females (72.4%, n=1496). Estimated 1099 (53.2%) were students, 428 (20.7%) were unemployed, and 540 (26.1%) were. The majority were Saudis (94.7%, n= 1957). Psychological syndromes anxiety (60.7%), stress (60.7%), and depression (60.6%) were most frequent; whereas, IBD (48.7%) and GERD (36.3%), respectively were the second and third. In 51 % respondents depression, anxiety, and stress occurred first while in 33.9%, and 24.3% IBD and GERD, respectively, were the first signs. In most respondents (59.2%, n=1178), these signs first appeared recently and 33.6% (n=669) reported occurrence during adult life, and only in 7.2% (n=144) the signs noticed during childhood (7.2%, n=144)). Aggravating factors were 32.9% (n=681) genetic and other factors of which 476 (69.9%) inherited IBD while 215(31.6%) and 175 ((25.7), respectively, inherited psychological (depression, anxiety, and stress) and GERD. However, only 18.3% sought treatment (n=378) and only 66 (3.2%) had colectomy or a colostomy bag. Little over half of the studied population (58.1%, n=1201) were active in outdoor. GERD or IBS and psychological factors (anxiety, depression, and stress), were significantly associated with age (P value =.001).; GERD with old age, IBD with mid-age 40-49 years, and psychological disorders among younger ages. Thus, while mental health issues predispose young millennial women to neurogastroenterological disorders, the IBD and GERD initiate psychological problems in old and mid-ages, respectively. Intriguingly, despite the significantly mosaic global genetic population structures, their lifestyles, and nutritional habits, the pattern of these disorders remains similar. Thus, this is potentially consistent with notion that the gut nerve cells are conserved and that the changes in gut dysbiosis of gut microbiome signatures are responsible. These findings have significant clinical implications in the patient treatment strategies and tailored educational and awareness programs in lifestyle medicine. Future microbiome studies would reveal more insight into the mechanisms of disorders.

Biobased greases are derived from renewable resources, being considered more environmentally friendly, and offering comparable performance with petroleum-based greases. In this study, lubricating greases from frying cooking oils were prepared, thus valorizing waste, in order to obtain sustainable and environmentally friendly products. 12 batches (500 g each) were produced from sunflower and palm frying oils, with 20% by weight calcium/ lithium stearate soaps prepared in situ, and additivated with 15% wt. cellulose or lignin sulphate. The greases were rheologically characterized. Their consistency was assessed by the penetration test, performed before and after working the greases. Dropping point determinations offered information about the stability at higher temperatures, and oil bleeding tests were performed. The average values of the friction coefficient (COF), the contact resistance and the wear scar diameter were measured, through mechanical tests. Additivated greases prove to be comparable with those obtained from mineral oils, with good rheological properties, soft consistency and good antiwearing behavior, e.g.in open or total- loss lubricating systems, like in open gears and certain food processing machinery; they are thermally stable, and prone for use in low-loading working mechanisms.

Novel sensing technologies for liquid biopsies offer a promising prospect for the early detection of metabolic conditions through -omics techniques. Indeed, high-field NMR facilities are routinely used for metabolomics investigations on a range of biofluids in order to rapidly recognize unusual metabolic patterns in patients suffering from a range of diseases. However, these techniques are restricted by the prohibitively large size and cost of such facilities, suggesting a possible role for smaller, low-field NMR instruments in biofluid analysis. Herein we describe selected biomolecule validation on a low-field benchtop NMR spectrometer (60 MHz), and present an associated protocol for the analysis of biofluids on compact NMR instruments. We successfully detect common markers of diabetic control at low-to-medium concentrations through optimized experiments, including glucose (≤ 2.6 mmol./L) and acetone (25 μmol./L), and additionally in readily-accessible biofluids. We present a combined protocol for the analysis of these biofluids with low-field NMR spectrometers for metabolomics, and offer a perspective on the future of this technique appealing to point-of-care applications.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.

Background: Educating college students about the importance of good sleep habits could lead to the adoption of healthier sleep routines, including sufficient sleep duration and sleep quality. The current pre-post study examines the impact of completing a sleep education program called “Sleep 101” on (1) sleep hygiene practices, (2) sleep quality, and (3) weekday and weekend sleep behaviors among college students. “Sleep 101” is an interactive online course developed to educate college students about the importance of sleep by addressing basic sleep physiology, the impact of sleep on mood, academic and physical performance, the interactions between sleep and various substances, and common sleep disorders. Methods: 338 college students were recruited from a midsized public university in the US and invited to participate in “Sleep 101”, of which 25 participants completed the baseline and post-intervention questionnaire. The Sleep Hygiene Index (SHI) was utilized to evaluate sleep hygiene practices, while standard questions were employed to assess weekday and weekend sleep behaviors and overall sleep quality. Results: Those who completed the study demonstrated a significant increase in weekday sleep duration and were less likely to engage in negative prior bedtime activities. In addition, 40% of those who completed baseline and post-intervention assessments noticed improvements in their sleep quality. Conclusion: These findings suggest that a brief online program is beneficial in improving sleep behaviors among college and could be a scalable approach to addressing current sleep issues and preventing future sleep problems in college students.

The profile of secondary metabolites occurring in apple cuticular layer is not only characteristic for particular apple cultivar, but also dynamically reflects various external factors in growing environment. In this study, the possibility to authenticate apple samples based on analysis of their cuticular layer extracts was investigated. Ultra-high-performance liquid chromatography coupled to high resolution tandem mass spectrometry (UHPLC-HRMS/MS) was employed for obtaining metabolomic fingerprints. In total, 274 authentic apple samples, four cultivars harvested within the seasons 2020 to 2022 in the Czech Republic and Poland were analysed. The generated complex data processed by univariate and multivariate statistical methods enabled to build classification models for discrimination of apple cultivars as well as their geographical origin. The models showed very good performance in differentiation of Czech and Polish samples for three of four cultivars: ‘Gala’, ‘Golden Delicious’ and ‘Idared’, moreover, the validity of the models was verified over harvest seasons. The diagnostic markers, besides metabolites of triterpene biosynthetic pathway, mainly represented wax esters. ‘Jonagold’, which is known to be susceptible to mutations, was the only cultivar for which the unambiguous classification of geographical origin was not possible.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

Apis mellifera, especially weak ones, are highly vulnerable to Carpoglyphus lactis mites, which can rapidly infest and consume stored pollen, leading to weakened colonies and potentially colony collapse. This study aimed to ascertain and investigate the prevalence of this mite in honeybee colonies across 9 provinces in the Republic of Korea (ROK). A total of 615 honeybee colonies were collected, from 66 apiaries during the spring and 58 apiaries during the summer of 2023. A 1,242 bp segment of the the Cytochrome c oxidase subunit 1 (COI) gene was amplified using the polymerase chain reaction method. The detection levels of C. lactis in the honeybees were compared between winter and summer. Based on the COI sequence analysis, the nucleotide sequence similarity of C. lactis mites isolated in the ROK with those from China (NC048990.1) was found to be 99.5%, and with those from the United Kingdom (KY922482.1) was 99.3%. This study is the first report of C. lactis in Korean apiaries. The findings in this study demonstrate a significantly higher detection rate in winter, which is 4.1 times greater than that in summer (p < 0.001). Furthermore, the results underscore the usefulness of molecular diagnostic techniques for detecting C. lactis mites.

COX II containing a dual core CuA active site is one of the three core subunits of mitochondrial Cco, which plays a significant role in the physiological process. In this report, the full-length cDNA of COXⅡ gene was cloned from Sitophilus zeamais, which had an ORF of 684 bp encoding 227 amino acids residues. The predicted COXⅡ protein had a molecular mass of 26.2 kDa with pI value of 6.37, and multiple sequence alignment and phylogenetic analysis indicated that Sitophilus zeamais COXⅡ had high sequence identity 78.51% with the COXⅡ of other insect species, especially similarity to sitophilus oryzae. This gene was subcloned into the prokaryotic expression vector pET-32a, and induced by IPTG in E.coli Transetta (DE3) expression system. Finally the COXⅡ with 6-His tag was purified using affinity chromatography with Ni²⁺-NTA agarose. WB showed the recombinant COXⅡ was about 44 kD, and the concentration of fusion protein was 50μg/mL. UV-spectrophotometer and infrared spectrometer analysis showed that recombinant COXⅡ could catalyze the oxidation of substrate Cytc, and influenced by AITC. It was found that AITC could form a hydrophobic region with COXⅡ protein via molecular docking, besides, a sulfur atom of AITC structure could form a length of 2.9 Å hydrogen bond with Leu-31. These results will provide valuable information for elucidating the role of COXⅡ in Sitophilus zeamais responses to AITC, meanwhile, it will helpful to carry out a point mutation in AITC binding sites for the future research.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

This paper is focused on typical rural settlements in the Stara Planina Mountain area in Serbia. They are distinguished by their authenticity, identity and character, and they have still not been destroyed by inappropriate development as is the case in some other mountain areas in Serbia, where the effects of urbanization, globalization and homogenization are obvious. Consequently, there is a need to prevent these effects in mountain areas where there is a threat of disbalance between development and the inherited natural and cultural values. The paper starts from several important concepts that relate contemporary approaches to cultural heritage preservation, place morphology and planning future development. The concept definitions from recent documents from related fields are used. These concepts are then applied to the area of Stara Planina Mountain and its rural settlements. The necessity for an integrative approach to planning this area with significant natural and anthropogenic potential is pointed out, including its integration into international programs of sustainable development.

The research reported on this paper was aimed at improving the overall efficiency of a PDO certified artisanal cheese production process. Being a PDO certified foodstuff by the EU, it is considered to have properties and qualities determined by the geographical environment in which is made, with its production taking place in a specific and determined geographical location, in this case the Serra da Estrela region. In that sense, the authors conducted a mapping according to a systemic perspective of the processes involved in the context of manufacturing and distribution of certified Serra da Estrela cheese. Numerous methods were used throughout the process, such as a systemic design analysis, and techniques derived from ethnographic methods, which led to the collection of data in the field and consequently provided the immersion of the researcher in genuine work situations. Critical points were identified and emphasized in the systemic map with the purpose of encouraging initiatives to address and overcome the gaps and inefficiencies detected. The systemic design analysis triggered the development of design work. Observations following an ethnographic approach identified ergonomic risks in cheese making during the process of cutting excess chips, fostering the emergence of musculoskeletal disorders at the wrist. A tool that fits best to the task at hand was developed. A prototype of the new tool enabled collecting feedback from use in the work context, in order to inform product development. The domains of agricultural production and microbiology, considering the specific microorganisms developed trough the ripening process of the cheese, turned out to be aspects of high importance for the issue under focus, contributing to a broader understanding of the ripening process and its risks, simultaneously improving the efficiency and success of cheese production. If it were not for the systemic analysis, which served as a link between the boundaries of distinct domains such as the risk of microorganism contamination, ergonomics, energy efficiency, legislation and regulation policies, transportation challenges and economic viability, approached throughout the research. Simultaneously creating bridges between them, the various problems might not have been detected in the first place, as they are usually addressed in specialized disciplines, predetermined by the restrictions of each specific area of knowledge. As a consequence of the development of this research, which was based on an analysis that sought to establish possible connections between various disciplines and tried to constantly maintain a holistic perspective, making new connections and observing the issues from a new angle, apart from the already established methodologies. All this allowed to lay out the seeds for the development of a plan to tackle the critical points identified by the systemic analysis reported in this paper.

Promoting green development has become an important way to optimize the ecological and economic structure and promote sustainable development. The Yangtze River Economic Belt is an important economic corridor in China, and it remains to be examined whether the implementation of environmental regulations has enhanced the green total factor productivity (GTFP) of cities. This paper calculates the green total factor productivity of 107 cities within the Yangtze River Economic Belt by using the super-efficient SBM model and the GML index with Chinese city panel data from 2007-2019 and measures the intensity of environmental regulations through textual analysis. The bidirectional fixed-effects model constructed in this paper suggests an inverted U-shaped relationship between environmental regulation and GTFP, which is confirmed by a series of robustness tests. Green technology innovation and advanced industrial structure play a mechanism role in this. In regions with lower levels of green technology and industrial structure, the inverted U-shaped relationship between environmental regulation and green total factor productivity is more significant. In addition, the phenomenon of GTFP rising and then falling because of environmental regulation is more obvious in cities in the middle and upper reaches of the Yangtze River and outside the urban agglomerations. Therefore, when formulating environmental regulation policies, it is necessary to balance the relationship between economic development and environmental protection and harmonize the environment and economic development of the entire Yangtze River Basin.

The wetlands in northeastern Bangladesh are home to some of the most prolific and valuable ecosystems on the planet, offering a wide range of benefits to both the local and wider communities. A limited number of research on this topic have been carried out in various wetlands in coastal hilsa, but none have been located in the northeastern region of Bangladesh. Thus, the goal of this study was to better understand the most commercially relevant species (anadromous hilsa) in northeastern Bangladesh as well as to assess the wetland ecosystem services more thoroughly with the contribution of their fish genetic resources. In addition to laboratory studies, fieldwork was done in the fishing settlements along the Surma River, Hakaluki Haor, and Tanguar Haor. The study classified 77 fish species into 21 subcategories of ecosystem services, of which 56% were not threatened, 17% were vulnerable, and 10% were highly endangered. The species Hilsa was found to be the most economically significant, accounting for 1% of the GDP overall. The study determined if the hilsa stock of the examined wetlands maintains a single or several subpopulations in comparison to other parts of the country when they migrate from saline water to northeastern Bangladesh (freshwater). But when compared to other groups, the FST score was between 0.000 to 0.017, indicating that the populations are identical and that there is genetic material sharing between them. Additionally, these statistics imply that the Sylhet haor and adjacent river systems contain a single stock of Hilsa fish. Nevertheless, a number of stresses and risks, including overexploitation, illicit and destructive fishing, siltation, and natural disasters like flash floods, have been linked to changes in the supply of hilsa and other ecosystem services. This study also emphasizes the necessity of policy attention and research to address the concerns.

In this paper, we introduce a specialized, fully automated experimental arrangement designed for assessing the effectiveness of augmented and virtual reality technologies in healthcare setting and explore its design principles focusing on depth sensor characterization. The main goal of this project is to establish a robust benchtop platform for the quantitative evaluation of extended reality technologies in a controlled environment, emphasizing the practical assessment of augmented reality head-mounted devices. We outline a design concept and considerations for an experimental configuration aimed at creating a realistic testing environment. This apparatus comprises an observation platform mounted on a three-degree-of-freedom motorized system and a test phantom stage. Focusing on real-case scenarios, we utilized a range of sensors, including readily available range-sensing cameras and commercial augmented reality headsets, such as the Intel RealSense L515 LiDAR camera, mounted on the motion control system. The setup enabled automated data collection and facilitates controlled assessments and validation of various facets of augmented reality technologies, including object, hand, and head tracking, as well as static and dynamic image registration. This paper describes the system architecture, the process of automated data collection, and presents several evaluation studies conducted with this setup, providing insights into the quality and temporal noise associated with static or moving objects or observers in augmented reality applications.

Alzheimer's disease is a multifactorial neurodegenerative disorder, with Acetylcholinesterase, Butyrylcholinesterase, Beta secretase, Glycogen Synthase Kinase beta and Monoamine oxidase B playing central role in it's pathogenesis. Therefore, this research aims to discover potential curative multitarget drugs derived from African natural products capable of addressing the multifactorial characteristics of the disease. In silico approaches were used to filter a 880 african natural compounds library based on selected pharmacokinetic properties. Molecular docking against the five aforementioned proteins, followed by Molecular Mechanics with Generalised Born and Surface Area Solvation scoring for the top compounds were used to assess binding. Density Functional Theory studies were used to assess electronic transitions. Pharmacokinetic filters resulted in 200 compounds, of which only five were selected after molecular docking. Density Functional Theory and Molecular Mechanics with Generalised Born and Surface Area Solvation scoring resulted in 3 potential multitarget compounds. Compound 157 (ZINC000095485950) showed triple-target inhibitory activity against Butyrylcholinesterase, Glycogen Synthase Kinase beta and Beta-secretase, while compounds 159 (ZINC000095485952) and 696 (ZINC000039144622) showed dual-target inhibitory activity against Butyrylcholinesterase and Glycogen Synthase Kinase beta. Molecular dynamics simulation and further experimental assessments are suggested.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.

To secure logic circuits against the illegal copying the insertion of the so-called key bit inputs using XOR/XNOR gates has been proposed in . The inserted gates modify (lock) the behavior of the original circuit and only the correct choice of the secret key bits guarantees the equivalent behaviour of the locked circuit to the original circuit. To break this kind of security, i.e. to find the secret key bits, there was a SAT solver based attack proposed in . The aim of this work is to experimentally verify this attack on several locked circuits with various number of primary inputs and outputs and with various number of gates. Except for the random placement of the key gates we evaluate also the positioning with chaining elimination. The obtained and presented results show that we were able to unlock 10 of 11 circuits within few minutes on a common PC.

Intermetallic compounds are increasingly being expected to utilize in tribological environments, but to date the works are hindered by insufficient ductility at low and medium temperature. This paper presents a novel multiphase intermetallic alloy with the chemical composition of Mo-40Ni-13Si (at.%). Microstructure characterization reveals that a certain amount of ductile Mo phases formed during the solidification process of ternary Mo-Ni-Si alloy melt, which is undoubtedly beneficial to the ductility improvement of intermetallic alloy. Tribological properties of the designed alloy, including wear resistance, friction coefficient and metallic tribological compatibility, were evaluated under dry sliding wear test conditions at room temperature. Results suggested that the multiphase alloy possesses an excellent property for room-temperature wear applications, which is attributed to the unique microstructural features and thereby good combination in hardness and ductility. The corresponding wear mechanism is also reported by observing the worn surface, subsurface and wear debris of alloy, which to be found is soft abrasive wear.

With the integrated development of the Internet, wireless sensor technology, cloud computing, and mobile Internet, there has been a lot of attention given to research about and applications of the Internet of Things. A Wireless Sensor Network (WSN) is one of the important information technologies in the Internet of Things; it integrates multi-technology to detect and gather information in a network environment by mutual cooperation, using a variety of methods to process and analyze data, implement awareness, and perform tests. This paper mainly researches the localization algorithm of sensor nodes in a wireless sensor network. Firstly, a multi-granularity region partition is proposed to divide the location region. In the range-based method, the RSSI (Received Signal Strength indicator, RSSI) is used to estimate distance. The optimal RSSI value is computed by the Gaussian fitting method. Furthermore, a Voronoi diagram is characterized by the use of dividing region. Rach anchor node is regarded as the center of each region; the whole position region is divided into several regions and the sub-region of neighboring nodes is combined into triangles while the unknown node is locked in the ultimate area. Secondly, the multi-granularity regional division and Lagrange multiplier method are used to calculate the final coordinates. Because nodes are influenced by many factors in the practical application, two kinds of positioning methods are designed: the unknown node is in the positioning unit or not. When the unknown node is on the side of the positioning unit, we use the method of vector similarity. Moreover, we use the centroid algorithm to calculate the ultimate coordinates of unknown node. When the unknown node is not on the side of the positioning unit, we establish a Lagrange equation containing the constraint condition to calculate the first coordinates. Furthermore, we use the Taylor expansion formula to correct the coordinates of the unknown node. In addition, this localization method has been validated by establishing the real environment.

The electroencephalogram (EEG) is a record of brain activity. Brain Computer Interface (BCI) technology formed by the EEG signal has become one of the hotspots at present. How to extract the feature signal of EEG is the most basic research of BCI technology. In this paper, A new method of recognizing fatigue, conscious, concentrated state of human brain is proposed by the combination of discrete wavelet transform and the neural network based on EEG signal. First of all, the law signal is preprocessed by the wavelet denoising method because the law EEG signal contains a large number of high frequency noise, which is decomposed into multi-layer high frequency signal and low frequency signal. thus, δ wave, θ wave, α wave, β wave are obtained by the wavelet transform. And then, frequency band energy of the different wave is regards as the feature signal of EEG. In the experiment, the feature signal is classified by radial basic function (RBF) and annealed chaotic competitive learning network (ACCLN). RBF and ACCLN networks are trained with 500 sets of sample data and are tested by 100 sets of samples in different mental states. The experimental results show that the average accuracy of RBF network under three conditions are 88.75%, 88.25%, 88.5%, respectively, and the correct rate of ACCLN network is 97%, 98%, 98%, respectively.

Early discharge after childbirth has led to a rise in neonatal readmission, becoming a major concern in recent decades. Our research aimed to identify the risk factors and incidence of neonatal readmission, as well as explore preventive measures. Our study at the Clinical Hospital of Pediatrics in Ploiești, Romania included 108 neonates admitted during the neonatal period. This accounted for 2.06% of all admissions (5226). The most prevalent cases were malnutrition (25%), fever (20.3%) and bronchiolitis (17.5%). Diarrhea and infectious gastroenteritis were also observed (14.8%), along with acute rhinoconjunctivitis (9.2%) and late onset sepsis (3.7%). No deaths were recorded. The most significant characteristics identified were number of children (p<0.001) and age at maternity discharge (p<0.001). By following the prevention rules, malnutrition, feeding errors, and infections can be avoided. This includes practicing proper hand hygiene for both mothers and medical staff, as well as educating and demonstrating to mothers the benefits of breastfeeding. In addition, all newborns discharged from the maternity ward should benefit from follow-up at 7-10 days of life. Our results confirm the effectiveness of a multidisciplinary team and endorse promoting breastfeeding. Implementing quality control measures and regularly evaluating the surveillance program will help improve its effectiveness.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

Two interesting compounds such as quaternary ammonium lignin(QAL) and 2-ethylhexyl phosphoric acid mono-2-ethylhexyl ester (P507) were synthesized as ionic liquids(QP-ILs) for the extraction of metal ions. The extraction behavior of Co(II) and Ni(II) from chloride solution was compared between QP-ILs and P507. The results showed that the extraction rates of Co(II) and Ni(II) in the two solutions varied with the extraction conditions, but QP-ILs has stronger extractability for cobalt than P507, while Ni is on the contrary. Under the same conditions, the Co/Ni separation performance(βCo/Ni) in QP-ILs is superior to that in p507. At pH4.0, 55℃, concentration of 20%, extraction time of 10 minutes, the βCo/Ni of QP-ILs reached to 2703, while that of P507 was only 164. In conclusion, QP-ILs was more efficient than P507 for separating Co from mixed solutions.

Brain aging causes a wide variety of changes at molecular and cellular levels, leading to the decline of cognitive functions and increased vulnerability to neurodegenerative disorders. The research aimed at understanding the aging of the brain has made much progress in recent decades. Technological innovations such as single-cell RNA-sequencing (scRNA-seq), proteomic analyses, and spatial transcriptomic analyses have facilitated the research on the dynamic changes occurring within neurons, glia, and other cells along with their impacts on intercellular communication during aging. In this review, we introduce recent trends of how neurons and glia change during aging and discuss the impact of the brain microenvironment such as the blood-brain barrier (BBB).

In this paper, we study the semilinear pseudo-parabolic equations $\displaystyle u_{t} - \triangle_{\mathbb{B}}u - \triangle_{\mathbb{B}}u_{t} = \left|u\right|^{p-1}u$ on a manifold with conical singularity, where $\triangle _{\mathbb{B}}$ is Fuchsian type Laplace operator investigated with totally characteristic degeneracy on the boundary $x_{1} = 0$. Firstly, we discuss the invariant sets and the vacuum isolating behavior of solutions with the help of a family of potential wells. Then, we derive a threshold result of existence and nonexistence of global weak solution: for the low initial energy $J(u_{0})<d$, the solution is global in time with $I(u_{0}) >0$ or $\displaystyle\Vert \nabla_{\mathbb{B}}u_{0}\Vert_{L_{2}^{\frac{n}{2}}(\mathbb{B})} = 0$ and blows up in finite time with $I(u_{0}) < 0$; for the critical initial energy $J(u_{0}) = d$, the solution is global in time with $I(u_{0}) \geq0$ and blows up in finite time with $I(u_{0}) < 0$. The decay estimate of the energy functional for the global solution and the estimates of the lifespan of local solution are also given.

Multimodal remote sensing data classification can enhance the model’s ability to distinguish land features through multimodal data fusion. In this context, how to help models understand the relationship between multimodal data and target tasks is the focus of researchers. Inspired by human feedback learning mechanisms, causal reasoning mechanisms, and knowledge induction mechanisms, this paper integrates causal learning, reinforcement learning, and meta learning into a unified remote sensing data classification framework and proposed the causal meta-reinforcement learning (CMRL). First, based on feedback learning mechanisms, we have overcome the limitations of traditional implicit optimization of fusion features and customized a reinforcement learning environment for multimodal remote sensing data classification tasks. Through feedback interactive learning between agents and the environment, we help them understand the complex relationships between multimodal data and labels, thereby achieving full mining of multimodal complementary information. Second, based on the causal inference mechanism we designed causal distribution prediction action, classification reward, and causal intervention reward, capturing pure causal factors in multimodal data and cutting off false statistical associations between non-causal factors and class labels. Finally, based on the knowledge induction mechanism, we designed a bi-layer optimization mechanism based on meta-learning. By constructing a meta training task and meta validation task simulation model in the generalization scenario of unseen data, we helped the model induce cross-task shared knowledge, thereby improving its generalization ability for unseen multimodal data. The experimental results on multiple sets of multimodal datasets show that the proposed method achieved state-of-the-art performance in multimodal remote sensing data classification tasks.

Moso bamboo is famous for fast growing and biomass accumulation, as well as high annual output for timber and bamboo shoots. These high outputs require high nutrient inputs to maintain and improve stand productivity. Soil nitrogen (N), phosphorus (P) and potassium (K) are important micronutrients for plant growth and productivity. Due to high variability of soils, analysing spatial patterns of soil N, P and K stocks is necessary for scientific nutrient management in Moso bamboo forests. In this study, soils were sampled from 138 locations across Yong’an City and ordinary kriging was applied for spatial interpolation of soil N, P and K stocks. Soil N stock showed a strong spatial dependence while soil N and P stocks presented a moderate spatial dependence, indicating soil N was mainly controlled by intrinsic factors while soil N and P stocks were controlled by both intrinsic and extrinsic factors. Different spatial patterns were observed for soil N, P and K stocks across the whole study area, indicating that fertilizations with different ratios of N:P:K should be applied for different sites to maintain and improve stand productivity. The total soil N, P and K stocks within 0-60 cm were 0.624, 0.020 and 0.583 Tg, respectively.

With the increasing concern of environment, the energy-efficiency scheduling of manufacturing industry is becoming urgent and popular. In turning processes, both spindle speed and processing time can affect the final energy consumption and thus the spindle speed and scheduling scheme need to be optimized simultaneously. Since the turning workshop can be regarded as the flexible flow shop, this paper formulates a mixed integer linear programming model for energy-efficient scheduling of flexible flow shop. Accordingly, a new decoding method is developed by considering of the optimization of spindle speed and scheduling scheme simultaneously, and an estimation of distribution algorithm adopting the new decoding method is proposed to solve large-size problems. The parameters of this algorithm are determined by statistical technique with a simplified practical case. In order to validate the proposed method, a case from practical factories is studied, in which the makespan can be shortened by 25.22%, and the consumed energy can be saved by 5.48%. These results demonstrate the effectiveness of the proposed mathematical model and algorithm.

Lignocellulosic biomass, an abundant and renewable resource, serves as a crucial raw material for the production of biofuels, biochemicals, and various value-added products. This paper aims to develop and optimize a mild alkaline treatment of sawdust assisted by ultrasound, along with enzymatic hydrolysis of the pretreated material. The sonochemical pretreatment with alkali emerged as the optimal approach to enhance the susceptibility of cellulose to subsequent enzymatic hydrolysis, thereby increasing the yield of reducing sugars. A comparative study was performed using various ultrasonic applicators (horn and bath) and conventional assisted alkaline pretreatment. The ultrasonic assisted pretreatment revealed a higher delignification as 68% (horn) and 57% (bath) comparing with conventional pretreatment. Processes were optimized using a statistical analysis based on a 23 factorial design. The ratio between sawdust and alkanine solution (RSL = 0.5–1.5 g/100 mL), US amplitude (A = 20–60%), and working temperature (t = 30–50 °C) were selected as process factors. The optimal operating conditions to maximize the reducing sugar yield (138.15 mg GE /gsubstrate) were found as following: solid/liquid ratio RSL,opt = 1.25 g/100 mL, US amplitude Aopt = 60%, and and pretreatment temperature topt = 50 °C. The overall outcomes clearly confirmed the intensification of delignification by ultrasound assisted alkaline pretreatment

At 12:28 UTC (8:28 PM, local time) on 15 January 2023, a shallow, moderate earthquake with a magnitude (Mw) of 4.7 and a depth of one (1) kilometer shook the northern part of Leyte Island in the central part of the Philippines. The ground shaking was felt at PHIVOLCS Earthquake Intensity Scale (PEIS) VI, (very strong) equivalent to Modified Mercalli Intensity (MMI) VI in areas along the strike of the Leyte segment of the Philippine Fault. Even though this earthquake is classified as moderate in size, significant geologic, structural, and socio-economic impacts were documented. Most of the earthquake impacts that include surface rupture, liquefaction, and mass movements are limited near the epicentral area. The earthquake produced an 8-km-long surface rupture, the first documented rupture generated by a magnitude &lt;6 along the Philippine Fault, and is unusual in other surface rupturing earthquakes worldwide. It injured 18 persons and damaged 434 residential buildings and 26 public infrastructures which amounts to about 500 thousand US dollars. Structural damages were caused by surface rupture and/or poor engineering construction practices. Analysis of the seismic waveform and recorded peak ground acceleration (PGA) suggests that the subsurface geology influenced the ground motion amplification in an area near the epicenter. Based on the hypocenter, focal mechanism solution, aftershock distribution, and actual field observation, the causative fault for this event is the northern end of the Philippine Fault – Leyte segment. Moderate in size, this earthquake emphasizes the need and importance of documenting moderate-sized earthquakes as a tool and guide for medium and long-term earthquake risk assessment and resiliency.

Background: The bacterium Capnocytophaga spp. is a part of the oral microbiome of dogs, which has zoonotic potential. This study aimed to assess factors that influence the prevalence of Capnocytophaga cynodegmi and Capnocytophaga canimorsus in Wrocaw’s dog population. Methods: Molecular detection (PCR) involved 105 swabs, examining parameters such as oral cavity condition, underlying health issues, recent antibiotics, age, medications, material collection, and dog chews. Results: The study highlighted significant associations between the presence of Capnocytophaga cynodegmi and oral cavity condition, material collection method, and use of dog’s chews. Conclusions: Correlations obtained in this study between the oral health of Wroclaw's dog population and the presence of Capnocytophaga cynodegmi suggest its significance in the oral microbiome of dogs. Limitations, including the small sample size, highlight the need for more research to comprehensively understand additional factors that affect the prevalence of Capnocytophaga spp. in dogs

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.