In this paper, the fixed-time stabilization problem for a class of uncertain chained system is addressed by using a novel nonsingular recursive terminal sliding mode control approach. A fixed-time controller and an adaptive law are designed to guarantee the uncertain chained form system both Lyapunov stable and fixed-time convergent within the settling time. The advantage of the controller based on the sliding mode is that the settling time does not depend on the system initial state. Furthermore, we use RBF neural network to estimate the uncertainty of the system. Finally, the simulation results demonstrate the performance of the control laws.

Metal halide perovskites have shown excellent optoelectronic properties, including high photoluminescence quantum yield, tunable emission wavelength, narrow full-width at half-maximum and low-cost solution-processed fabrication, which make it exhibit great potential as the emission layer materials of light emitting diodes. With the joint efforts of researchers from different disciplines, there has been a significant progress in the improvement of external quantum efficiency (EQE) and stability of perovskite light emitting diodes (PeLEDs) in recent few years, especially in green PeLEDs with EQE over 30%. In this review, we firstly introduce the basic device structure of PeLEDs, as well as the factors influencing EQE and stability of PeLEDs. Secondly, the development of lead-based and lead-free PeLEDs are summarized systematically. Thirdly, challenges of PeLEDs are discussed in detail, including low EQE of blue PeLEDs, poor device stability and EQE roll-off. Finally, some suggestions and perspectives of the future research directions for PeLEDs are proposed.

Quantitative determination of the critical size of inclined coal pillar in old goaf water affected area is of great significance for water damage prevention and safe mining. The critical size of inclined waterproof coal pillar is derived by using theoretical analysis, numerical calculation and field engineering practice for the stability of the waterproof coal pillar in old goaf water affected area of 1303 working face of Dananhu I mine in Xinjiang region. Firstly, a force model of inclined waterproof coal pillar was established to reveal the law that the critical size of the coal pillar increases with the increase of coal seam inclination under the action of asymmetric load. Then, numerical simulation was applied to reveal the dynamic evolution process of plastic deformation-destabilization-destruction of section coal pillar under the influence of mining and single-side water pressure, and the critical size of waterproof coal pillar in study area was determined to be 19.09m. Finally, measures such as pumping and pressure relief and slurry reinforcement were adopted to reduce the deformation rate of the roadway on side of waterproof coal pillar, which ensured the stability of the coal pillar and roadway and the safe recovery of the working face.

With the development of designing and manufacturing level for micro-electromechanical system (MEMS) gyroscopes, the control circuit system becomes a key point to determine their internal performances. Nevertheless, phase delay of electron components may result in some serious hazards. This paper describes a real-time circuit phase delay correction system for MEMS vibratory gyroscopes. A detailed theoretical analysis is provided to clarify the influences of circuit phase delay on the in-phase and quadrature (IQ) coupling characteristics and zero rate output (ZRO) utilizing force-to-rebalance (FTR) closed-loop detection and quadrature correction system. By deducing the relationship between amplitude-frequency, phase-frequency of MEMS gyroscope and the phase relationship of the whole control loop, a real-time correction system is proposed to automatically adjust the phase reference value of phase-locked loop (PLL) and thus compensate for the real-time circuit phase delay. The experimental results show that the correction system can accurately measure and compensate the circuit phase delay in real time. Furthermore, the unwanted IQ coupling can be eliminated and the ZRO is decreased by 755% to 0.095°/s. This correction system realizes a small angle random walk of 0.978°/√h, and a low bias instability of 9.458°/h together with a scale factor nonlinearity of 255 ppm at room temperature. Besides, the thermal drift of ZRO is reduced to 0.0034°/s/°C at a temperature range from -20°C to 70°C.

Abstract: The purpose of this study is to explore, from the perspective of government interven-tion, behavioral logic and game relationship among farmers, service organizations and the gov-ernment in the pest and disease control outsourcing system, as well as the endogenous motiva-tion of each subject. The results indicate that the stronger the willingness of each subject, the faster the stable state of joint pest and disease control among the three parties can be formed; In the case of implementing a single policy tool, the convergence rate of each party that imple-ments the regulatory policy alone is fast but may be unstable, while the rate is slow but more stable when a guidance- or incentive-based policy is solely applied; The effect of policy tool combination is much better than that of a single policy tool applied. The simultaneous imple-mentation of the three types of policy tools can form a policy system with both positive and negative mechanisms, which can maximize complementary and superposition effect.

Weather surveillance radars routinely detect smoke of various origin. Of particular significance to the meteorological community are wildfires in forests and/or prairies. For example, one responsibility of the National Weather Service in the USA is to forecast fire outlooks as well as to monitor wild fire evolution. Polarimetric variables have enabled relatively easy recognitions of smoke plumes in data fields of weather radars. Presented here are the fields of these variables from smoke plumes caused by grass fire, brush fire, and forest fire. Histograms of polarimetric data from plumes contrast these three cases. Most of the data are from the polarimetric Weather Surveillance Radar 1988 Doppler (WSR-88D aka Nexrad, 10 cm wavelength) hence the wavelength does not influence these comparisons. Nevertheless, in one case simultaneous observations of a plume by the operational Terminal Doppler Weather Radar (TDWR, 5 cm wavelength) and a WSR-88D is used to infer backscattering characteristic and hence sizes of dominant contributors to the returns. In addition, comparisons with observations by other investigators of plumes from urban area but at a 5 cm wavelength are made. To interpret some measurements Computational Electromagnetics (CEM) tools are applied.

Geological structures such as joints and faults in rock mass have significant influence on open pit mining. Hence, it is critical to develop a understanding of dynamic joint behaviour under blasting loading. This in turn can provide both theoretical and practical guidance to improve blasting rock fragmentation and associated bucket excavating efficiency. In this paper, delayed blasting on the highwall bench at Baiyunebo open-pit mine was used as an example, a nonlinear joint blasting model was also constructed. By simplifying the blasting wave propagation velocity, the P-wave normal incidence to the joint was obtained. The peak vibration velocity was 0.33m/s at 3.0s. The S-wave reflected by the joint interface was first reflected backward and then forward, which the peak vibration velocity was 0.027 m/s. By combining the relevant stress and displacement theories of type I and II cracks, the equipotential diagrams of the stress and displacement field with the vibration velocity of the particle were obtained. σx was positive in the direction of 0~330° and subjected to tensile stress, whereas σy was positive in the direction of 0~180° and under tensile stress. The longitudinal σy along joint was low in compressive stress distribution area and did not affect surrounding rock at the time. The stress concentration appeared in the lower right corner. Based on the continuous behavior of stress wave in joints, the asymmetry and continuous changes reflected in the whole process could not be analysed by the contour diagram. Hence, ANSYS used to analyse distribution of the stress field. The intensity of the shock wave after detonation was greater than that of the rock strength. Subsequently, the sub-layer shock wave supplemented the shock wave energy that was not enough to break the rock and induced further cracking. This was able to be visualized by the degree of color change post-processing. It was concluded that with the attenuation of the detonation wave energy, the stress exhibited a decreasing trend in this process. According to distribution of the peak effective stress, it was found that the peak value first increased to 10-12 MPa and then showed a downward trend. Overall, the results were validated against the finite element simulation and mathematical analysis.

Conducting computational stress-strain analysis using finite element methods (FEM) is a common approach when dealing with the complex geometries of atherosclerosis, which is a leading cause of global mortality and complex cardiovascular disease. The considerable expense linked to FEM analysis encourages the substitution of FEM with a considerably faster data-driven machine learning (ML) approach. This study investigated the potential of end-to-end deep learning tools as a more effective substitute for FEM in predicting stress-strain fields within 2D cross sections of arterial wall. We first proposed a U-Net based fully convolutional neural network (CNN) to predict the von Mises stress and strain distribution based on the spatial arrangement of calcification within arterial wall cross-sections. Further, we developed a conditional generative adversarial network (cGAN) to enhance, particularly from the perceptual perspective, the prediction accuracy of stress and strain field maps for arterial walls with various calcification quantities and spatial configurations. On top of U-Net and cGAN, we also proposed their ensemble approaches to further improve the prediction accuracy of field maps. Our dataset, consisting of input and output images, was generated by implementing boundary conditions and extracting stress-strain field maps. The trained U-Net models can accurately predict von Mises stress and strain fields, with structural similarity index scores (SSIM) of 0.854 and 0.830 and mean squared errors of 0.017 and 0.018 for stress and strain, respectively, on a reserved test set. Meanwhile, the cGAN models in a combination of ensemble and transfer learning techniques demonstrate high accuracy in predicting von Mises stress and strain fields, as evidenced by SSIM scores of 0.890 for stress and 0.803 for strain. Additionally, mean squared errors of 0.008 for stress and 0.017 for strain further support the model's performance on a designated test set. Overall, this study developed a surrogate model for finite element analysis, which can accurately and efficiently predict stress-strain fields of arterial walls regardless of complex geometries and boundary conditions.

Fiber distributed optical fiber acoustic sensor (DAS) is generally used in distributed long-distance acoustic/vibration measurement. We found that DAS with excellent performance of low self-noise and anti-fading in combination with the plastic structure in daily life as an acoustic transducer can achieve high-sensitivity acoustic measurement at a single point rather than designing a state-of-the-art acoustic transducer or using special enhanced scattering fiber. The simple acoustic transducer we proposed for DAS can reach the sensitivity level of -106.5dB re. 1rad/μPa at a sensing range of 5.1 km, which can meet many demands on the industrial site.

To improve carbon efficiency for urban logistics service system composed of a third-party logistics service provider (3PLs) and an e-business enterprise, low-carbon operation game between them was studied. Considering low carbon technology investment cost and sales expansion effect of low carbon level, profit functions for both players were constituted. Based on their different bargaining capabilities, totally 5 types of game scenarios were designed. Through analytical solution, Nash Equilibria under varied scenarios were obtained. By analyzing these equilibria, 4 major propositions were given, in which, some key variables and system performance index were compared. Results show that the best system yields could only be achieved under the fully cooperative situation; limited cooperation only for carbon emission reduction would not benefit the system performance improvement; E-business enterprise-leading game’s performance overtook 3PLs-leading ones.

The organic coating of bridge steel girders is subjected to physical scratches, corrosion, and aging in natural weathering. The breakdown of the coating may cause serviceability and safety problems if left unnoticed. A hyperspectral imaging method is proposed to detect the condition of steel coatings based on coating-responsive features in reflectance spectra. A field test was conducted on the real-world bridge which shows obvious signs of degradation. The hyperspectral signature enables an assessment of the coating health and defect severity. The results indicated that the coating scratch can be effectively located in the domain of a hyperspectral image and the scratch depth can be determined by mapping a scratch depth indicator (SDI=R532nm / R641nm). Rust sources and products in steel girders can be identified by the unique spectral signatures and the rust stains (and thus stain areas) scattered on the coating can be pinpointed at pixel level by the corrosion rust indicators. The chemical integrity of a topcoat is demonstrated by the short-wave infrared spectroscopy and the topcoat degradation can be evaluated by the absorption at 8000 cm-1 and 5850 cm-1.

This paper presents a calibration and thermal compensation method that aims to minimize cost and processing time while maintaining high accuracy. First, the number of positions to perform the calibration procedure is optimized, and then, based on this optimized calibration number, thermal compensation is performed, which is necessary for environments with large temperature variations, since calibration parameters change at different temperatures. The calibration procedures and algorithms were experimentally validated on marketed accelerometers. Based on the optimized calibration method, the calibrated results have been obtained nearly 100 times improvement. Thermal drift calibration experiments on the triaxial accelerometer show that the thermal compensation scheme in this paper can effectively reduce drift in the temperature range of -40°C to 60°C. The temperature drifts of x- and y-axes are reduced from -13.2 and 11.8 mg to -0.9 and -1.1 mg, respectively. The z-axis temperature drift is reduced from -17.9 to 1.8 mg. We have conducted various experiments on the proposed calibration method and demonstrated its capacity to calibrate the sensor frame error model (SFEM) parameters. Therefore, the MEMS sensors calibrated in this paper have certain engineering application values for tilt measurement.

In recent years, compound glass microsphere resonator devices have attracted increasing interest and have been widely used in sensing, microsphere lasers, and nonlinear optics. Compared with traditional silica resonators, compound glass microsphere resonators have many significant and attractive properties, such as high-Q factor, an ability to achieve high rare earth ion, wide infrared transmittance and low phonon energy. This review provides a summary and a critical assessment of the fabrication and the optical characterization of compound glasses and the related fabrication and applications of compound glass microsphere resonators.

Oligopeptide transporters (OPTs) are a group of membrane localized proteins that have a broad range of substrate transport capabilities and contribute to numerous biological processes. However, limited information has been reported on OPTs in higher plants. In this study, a comprehensive analysis of the OPT gene family in Medicago truncatula was performed. A total of 26 OPT genes (MtOPT01-MtOPT26) have been identified in the Medicago truncatula genome. Phylogenetic analyses indicated that MtOPTs consisted of two distinct subgroups, 12 MtOPTs belonged to the peptide transport subgroup (PT-OPT) based on their predicted amino acid sequences containing the two highly conserved motifs (NPG and KIPPR) and 14 MtOPTs belonged to yellow stripe subgroup (YS-OPT). The MtOPTs distributed on each of 8 chromosomes in Medicago truncatula. Sequence analysis verified that MtOPTs significant similar to those in other plants. The copy number of MtOPTs was low and the multiply of MtOPTs was simple relatively. Gene structure analysis showed that most of the MtOPTs have various numbers of introns. The multiple of MtOPTs might play different biological roles which were supported by the fact that MtOPTs have a distinct tissue-specific expression pattern. The data obtained in this study will help to better understand the complexity of the MtOPTs gene family and provide new evidence for the function and evolution of the OPT gene family in higher plants.

To ensure consumers can purchase high-quality rice, accurate identification of rice varieties is particularly important. Methods: This article conducts research based on machine learning algorithms from the perspectives of image, spectrum, and spectrogram fusion. Six types of hyperspectral image data of rice were preprocessed using convolutional smoothing (SG) and multiple scatter correction (MSC). Texture information of the images was extracted using gray-level co-occurrence matrix. Spectra, texture, and spectrogram data were fused into a new matrix. Spectral, texture, and spectrogram fusion data were used as inputs for the model, and support vector machines (SVM), logistic regression (LR), and K-nearest neighbors (KNN) classification models were constructed and compared. Results: From the classification results, the spectrogram fusion classification performance was better than classification models using only spectra or texture. Conclusion: The research results showed that the accuracy of SVM and LR classification models exceeded 90%, and the LR model performed the best, effectively classifying rice varieties.

A challenge in building large-scale superconducting quantum processors is the precise control and manipulation of the qubit state. However, the crosstalk between the microwave control lines impedes the parallel execution of high-fidelity digital and analog quantum operations. Here, we propose and demonstrate a universal compensation protocol for calibrating the microwave signal crosstalk. We also introduce amplified error sequences to optimize the accuracy. Furthermore, we show a definitive improvement in parallel gate operations with crosstalk cancellation, demonstrating the technique's effectiveness. This work paves the way for superconducting hardware that features automated calibration of microwave crosstalk, leading to enhanced fidelities in multiqubit circuits.

The goods and services produced by forest and vegetation ecology system is the power by which human society can be promoted fast in high-quality and sustainable way. With the increase of population and economic development in water-limited regions, there is an increasing demand for the quantity and variety of forest vegetation ecosystem products and services. To meet the demands of this situation, most of the original forest has changed into farmland, non-native forest and grass land. As a result, water-plant relationship changed from equilibrium to non-equilibrium, which led to soil drought, soil degradation and vegetation decline in dry years or waste of soil water in rainy years in most of water-limited regions. In order to solve the questions and realize the sustainable utilization of soil water resources and the high quality and sustainable development of social economy, it is necessary to apply the utilization limit theory of soil water resources by plants and the theory of soil water carrying capacity for vegetation to adjust the relationship between plant growth and soil moisture to obtain the maximum yield and benefit of vegetation and serve high-quality and sustainable development.

The goods and services produced by forest vegetation ecosystem are the driving force for the rapid, high-quality and sustainable development of human society. In history, with the increase of population and economic development, there is an increasing demand for the quantity and variety of forest vegetation ecosystem products and services in a country or a region. To meet the demands, most of the original forest has become farmland, plantation and grass and crops land. As a result, the plant water relationship changed from equilibrium to non-equilibrium, which easily led to soil drought, soil degradation and vegetation decline in dry years or waste of soil water in rainy years in most of water-limited regions. In order to solve the question and realize the sustainable utilization of soil water resources and the high-quality sustainable development of forest, it is necessary to apply the limit theory of plant utilization of soil water resources and the vegetation carrying capacity theory in the critical period of plant-water relationship regulation to adjust the relationship between plant growth and soil moisture to obtain the maximum yield and benefit and realize high-quality and sustainable development.

Urbanization is considered as a main indicator of regional economic development due to its positive effect on promoting industrial development; however, many regions, especially developing countries, are troubled by its negative effect — the aggravating environmental pollution. Many researchers have indicated that rapid urbanization stimulated the expansion of industrial production scale and increased industrial pollutant emissions. However, this judgement contains a grave deficiency in that urbanization not only expands industrial production scales but can also increase industrial labour productivity and change the industrial structure. To modify this deficiency, we first decompose the influence which urbanization impacts on industrial pollutant emissions into the scale effect, the intensive effect and the structure effect by using the Kaya Identity and the LMDI Method; second, we perform an empirical study of the three effects’ impacts by applying the spatial panel model with data from 282 Chinese cities between 2003 and 2013. Our results indicate that (1) there are significant reverse U-shapes between Chinese urbanization rate and its industrial pollutant emissions; (2) the scale effect and the structure effect have aggravated Chinese industrial waste water discharge, sulphur dioxide emissions and soot (dust) emissions, while the intensive effect has generated a decreasing and ameliorative impact on that aggravated trend. The definite relationship between urbanization and industrial pollutant emissions depends on the combined influence of the scale effect, the intensive effect and the structure effect; (3) there are significant spatial autocorrelations of industrial pollutant emissions between Chinese cities, but the spatial spillover effect from other cities does not aggravate local urban industrial pollutant emissions, we offer an explanation to this contradiction that the vast rural areas surrounding Chinese cities have served as sponge belts and have absorbed the spatial spillover of cities’ industrial pollutant emissions. According to the results, we argue that this type of decomposition of the influence into three effects is necessary and meaningful, it establishes a solid foundation for understanding the relationship between urbanization and industrial pollutant emissions, and effectively helps to meet relative policy making.

In this study, we investigate the behavior of randomly moving particles with a defined average energy, focusing on their biased motion around a specific point. These particles' velocity magnitudes follow a Maxwell distribution with a specific scale parameter. Our analysis derives the stochastic rotation rules for these particles and introduces the Ito equation conditions for biased stochastic rotation at a given curl value. We also consider the special relativistic-like effects in this context. The findings are validated through a representative example.

In a particle swarm with a fixed kinetic energy, the constituent particles move randomly and their velocity magnitudes follow a Maxwell distribution characterized by specific parameters. Within a certain time frame, particles in a sub-swarm may exhibit a bias in their movement direction. Thus, the particles may exhibit a special characteristic (biased random motion), where the group velocity in a particular direction remains constant u. For this biased particle swarm, composed of randomly moving particles with a fixed average speed c, particles have a higher probability of moving in a specific direction. Conversely, their likelihood of moving in all other directions is equally reduced. This study starts from the perspective of biased random walks and using Mathematica software proves that the diffusion rate of particles (in the reference frame R_u observed from R₀) in all directions is slower than that of an unbiased particle swarm with the same average speed c. Specifically, the degree of reduction is determined by the Lorentz-like factor. Lastly, we present the Ito equation for this biased random motion and provide associated verification examples. This study aims to serve as a reference for comprehending the underlying principles of the special relativity effect.

There is a balanced plant-water relationship in the primary vegetation of desert area. With the increase of population and social development in desert areas, people’s need for forest vegetation ecosystem’s goods and service have been changed. To meet the growing demand for plant community goods and services, more original vegetation has been changed into non-native vegetation such as in China loess plateau. However, with the plant growth, sometime soil drying happens and then becomes gradually serious with times in most of desert regions. Serious drying of soil eventually result in soil degradation, vegetation decline and agriculture failure，which influence the produce and supply of forest vegetation goods and service in market in dry year or waste of soil water resources in wet year, which wastes precious nature resources. In order to solve these problems, the soil water resources have to be used in sustainable way and plant-water relationship have to be regulated on Carrying Capacity of Soil Water for Vegetation in the key period of plant water relationship regulation, to carry out sustainable use of nature resources, high-quality and sustainable development of forest and grass or high-quality produce of fruit and crop in desert re-gions.

Using the method of the beta function, Sun has recently evaluated some series of the type $\sum_{k=0}^{\infty}(ak+b)x^k/\binom{mk}{nk}$. By factorization of the polynomial $t^{m-n}(1-t)^n-x$, we will give a general method to find new $\pi$-series.

Pigs are susceptible to cold stress due to the absence of brown fat caused by the partial deletion of uncoupling protein 1 during their evolution. Some local pig breeds in China, exhibit potential cold adaptability, but research has primarily focused on fat and intestinal tissues. Skeletal muscle plays a key role in adaptive thermogenesis in mammals, yet the molecular mechanism of cold adaptation in porcine skeletal muscle remains poorly understood. This study investigated the cold adaptability of two pig breeds, Mashen pigs (MS) and Large White pigs (LW), in a 4-day cold (4°C) or room temperature (25°C) environment. We recorded phenotypic changes and collected blood, and longissimus dorsi muscle for transcriptome sequencing. Finally, a candidate gene was randomly selected for functional exploration in porcine skeletal muscle satellite cells. A decrease in body temperature and body weight in both LW and MS pigs under cold stress, accompanied by increased shivering frequency and respiratory frequency. However, MS pigs demonstrated stable physiological homeostasis, indicating a certain level of cold adaptability. LW pigs primarily responded to cold stress by regulating heat production and Glycolipid energy metabolism. MS pigs exhibited a distinct response to cold stress, involving regulation of heat production, energy metabolism pathways, robust fatty acid oxidation ability, and stronger immune response. Furthermore, the functional exploration of PRSS8 in porcine skeletal muscle satellite cells revealed it affected cellular energy metabolism and thermogenesis by regulating ERK phosphorylation. These findings shed light on the diverse transcriptional responses of skeletal muscle in LW and MS pigs under cold stress, offering valuable insights into the molecular mechanisms underlying cold adaptation in pigs.

This paper investigates the polarization and heat generation characteristics of batteries under different ambient temperatures and discharge rates by means of using a coupled electric-thermal model. The study found that the largest percentage of polarization is ohmic polarization, followed by concentration polarization and electrochemical polarization. The values of the three types of polarization are generally small and stable under normal-temperature environments and low-discharge rates. However, they increase significantly in low-temperature environments and high-discharge rates and continue to rise during the discharge process. Additionally, ohmic heat generation and polarization generation also increase significantly under these conditions. Reversible entropy heat is less sensitive to ambient temperature but increases significantly with the increase of the discharge rate. Ohmic heat generation and polarization heat generation contribute to the total heat generation of the battery at any ambient temperature, while reversible entropy heat only contributes to the total heat generation of the battery at the end of discharge.

Abstract: In recent years, the concentration of fine particulate matter (PM2.5) in China has decreased significantly, whereas the concentration of surface ozone (O3) has increased. The formation regime of ozone is closely related to the ratio of volatile organic compounds (VOCs) to nitrogen oxides (NOx). To reveal the reasons for this increase in ozone, we determined the sensitivity of ozone generation by determining the regional threshold of the ratio of formaldehyde to nitrogen dioxide (HCHO/NO2) in the satellite troposphere. The different FNR(HCHO/NO2) ratio ranges indicate three formation regimes: VOC-limited, transitional, and NOx-limited. The range of the transitional regime plays a crucial role in identifying the regime of ozone formation. Currently, the key threshold for ozone generation in China remains unclear. Polynomial fitting models were used to determine the threshold range for the transitional regime in the BTH region [2.0,3.1]. The ozone formation regime in the BTH region mainly exhibited a transitional and NOx-limited regime, and the overall concentration changes of the HCHO and NO2 columns in the BTH region showed a fluctuating trend from 2019 to 2022. However, compared to 2019, the ozone precursors and FNR showed varying degrees of decline in 2022. The concentration changes of NO2 were high in winter and low in summer, whereas the trend of HCHO and FNR changes was the opposite to that of NO2, being high in summer and low in winter. The concentrations of HCHO and NO2 in the BTH region showed a trend of urban agglomeration areas>urban expansion areas>non-urban areas in different land types from 2019 to 2022, whereas the FNR showed an opposite trend in urban agglomeration areas<urban expansion areas<non-urban areas.

In this paper, the Phase-Scheduled-Command FXLMS algorithm with the phase error between the disturbance and command signal is analyzed in detail. The influence of the phase error on the convergence time constant, convergence rate, and performance of convergence is explained for both stationary and nonstationary disturbance signals case. For stationary disturbance, the phase error slightly increases the convergence rate but heavily increases the distance of the optimum vector from the initial value, leading to poor convergence time constant performance. For nonstationary disturbance, the existence of phase error leads to poor convergence performance in every step, resulting in poor sound profiling performance. And the estimation of the phase error influence is developed in the closed form. Simulations are performed to demonstrate the validity of the analysis results.

Low separation efficiency of photogenerated carriers and inefficient utilization of visible light limit the application of g-C3N4 nanosheets (CNNs) in the field of photocathodic protection (PCP). Therefore, this work considered indium zinc sulfide (ZnIn2S4, ZIS) as a visible photosensitizer and an electronic donor to promote its PCP performance. ZIS nanolayers with nano-leaf structures were fabricated on CNNs by a simple hydrothermal method. The synthesized 30% ZIS@CNNs composites significantly enhanced the PCP performance for 316 stainless steel (SS) compared with pure CNNs. Under visible light illumination, the 30% ZIS@CNNs photoelectrode exhibited the largest photoinduced current density of 17.30 μA cm−2 and a photoinduced potential drop of 0.37 V, which was approximately 4 and 7.5 times higher than that of pure CNNs, respectively. The improved protection performance may be attributed to the significant increase in visible light absorption and the great enhancement in the separation efficiency of

A method of measuring the absolute pose parameters of a moving rigid body using a monocular camera is proposed, aiming at addressing calibration difficulties and inconsistencies of repeated measurements of the rigid-body pose for a camera having a varying focal length. The proposed method does not require calibration beforehand. Using more than six non-coplanar control points symmetrically arranged in the rigid-body and world coordinate systems, the matrices of rotation and translation between the camera and two coordinate systems are obtained and the absolute pose of the rigid body measured. In this paper, formulas of the absolute pose measurement of a moving rigid body are deduced systematically and the complete implementation is presented. Position and attitude measurement experiments carried out on a three-axis precision turntable show that the average absolute error in the attitude angle of a moving rigid body measured by an uncalibrated camera at different positions changes by no more than 0.2 degrees. Analysis of the three-dimensional coordinate errors of the centroid of a moving rigid body shows little deviation in measurements made at three camera positions, with the maximum deviation of the average absolute error being 0.53 cm and the maximum deviation of the standard deviation being 0.66 cm. The proposed method can measure the absolute pose of a rigid body and is insensitive to the position of the camera in the measurement process. This work thus provides guidance for the repeated measurement of the absolute pose of a moving rigid body using a monocular camera.

China’s rural e-commerce has been developing rapidly. Taobao Villages are combination of e-commerce and rural industries. When rural e-commerce coverage evolves from Taobao village to Taobao town, the scale of industrial clusters has been expanding synchronously. This paper investigates flower and seedling industrial cluster in Xinhe Town, Yanji Town and Miaotou Town of Shuyang County, China, and conducts the econometric analysis of the expansive determinants of flower and seedling industrial cluster of Taobao Villages. An effective sample of 263 was obtained through a face-to-face survey of e-merchants of flower and seedling in the Shuyang County of Jiangsu Province. Bases on the structural equation modeling, series of test results show that the data can be used to calculate the path regression. The outcomes shows that creation of e-merchants of flower and seedling, integration of e-commerce platform, supply chain friendliness, involvement of e-commerce service providers, and governmental policy guidance are driving expansion of flower and seedling industrial cluster together, moreover, the five forces interact with each other. This implies that expansion of flower and seedling industrial cluster is a systematic process, each stakeholder needs to pay attention to the role of other forces, and five forces achieve a balanced situation in the cluster.

Salmonella infections can lead to intestinal inflammation and metabolic disorders in birds. However, whether ARA metabolism is involved in Salmonella-induced intestinal inflammation remains unclear. This experiment investigated the changes in cecal flora and arachidonic acid (ARA) metabolism in Hainan Wenchang chickens infected with S. Typhimurium using 16s rDNA sequencing and targeted metabolomics. The results showed that the levels of ARA metabolites were increased in the cecum tissue of Wenchang chickens after infection with S. Typhimurium, including prostaglandin E2, prostaglandin F2α, lipoxin A4, ±8(9)-EET, ±11(12)-EET, and ±8,9-DiHETrE. The content of key enzymes for ARA production and metabolism (PLA2 and COX-2) in chicken cecum tissues was increased after S. Typhimurium infection. The relative mRNA levels of inflammatory factors were also increased after infection, including IFN-γ, TGF-β1, IL-4, and IL-6. In HD11 cells, the use of a cyclooxygenase (COX) inhibitor reduced the increased levels of COX-2 and PGF2α induced by S. Typhimurium infection and effectively reduced the inflammatory response. In addition, the number of beneficial genera (e.g., Bifidobacterium, Lactobacillus, and Odorobacterium) in the cecum of Wenchang chickens was significantly reduced after infection with S. Typhimurium. In this study, we revealed the structure of the cecal flora of Wenchang chickens infected with S. Typhimurium and demonstrated that S. Typhimurium can mediate the onset and development of intestinal inflammation through the activation of the metabolic pathway of ARA cyclooxygenase in Wenchang chickens. The results can provide data support and theoretical support for the prevention and control of avian salmonellosis.

We constrain two dynamical dark energy models that are parametrized by the logarithm form of $w(z)=w_{0}+w_{1}\left(\frac{\ln (2+z)}{1+z}-\ln 2\right)$ and the oscillating form of $w(z)=w_{0}+w_{1}\left(\frac{\sin(1+z)}{1+z}-\sin(1)\right)$. Comparing with the Chevallier-Polarski-Linder (CPL) model, the two parametrizations for dark energy can explore the whole evolution history of the universe properly. Using the current mainstream observational data including the cosmic microwave background data and the baryon acoustic oscillation data as well as the type Ia supernovae data, we perform the $\chi^2$ statistic analysis to global fit these models, finding that the logarithm parametrization and the oscillating parametrization are almost as well as the CPL scenario in fitting these data. We make a comparison for the impacts of the dynamical dark energy on the cosmological constraints on the total mass of active neutrinos. We find that the dark energy properties could significantly change the fitting results of neutrino mass. Looser constraints on $\sum m_{\nu}$ are obtained in the logarithm and oscillating models than those derived in the CPL model. Consideration of the possible mass ordering of neutrinos reveals that the most stringent constraint on $\sum m_{\nu}$ appears in the degenerate hierarchy case.

Spodoptera frugiperda (J.E. Smith) is a global agricultural pest that poses a threat to crop production, characterized by its refractory polyphagous nature that makes it difficult to control and may lead to damage to woody plants. However, research on its adaptability to woody plants remains limited. This study compares the feeding adaptations (survival rate, pupation time, pupation rate, weight, length, and feeding volume), protective enzyme activities, and feeding preferences of S. frugiperda on leaves of six economically significant tree species (Areca catechu, Aquilaria sinensis, Cocos nucifera, Camellia oleifera, Dalbergia odorifera and Hevea brasiliensis) and maize as a control treatment. The results indicate that A. sinensis as the most vulnerable trees in high risk, H. brasiliensis and C. nucifera presented varying degrees of susceptibility, A. catechu, C. oleifera, and D. odorifera were unsuitability for S. frugiperda. In conclusion, this report extensively explores the feeding effects of S. frugiperda on six economically important tree species, and provides insights into the feeding preferences on these plants, thereby informing the potential threat posed by S. frugiperda to economically vital trees.

Existing research indicates that mineralization of Carlin-type gold deposit is related to geological structures, but current studies mostly focus on the qualitative association, and lack quantitative analysis of the relationship between mineralization and structural features, which limits the potential for predictive mineral exploration. In this study, the Nibao Carlin-type gold deposit was selected as the research area to conduct three-dimensional geological modeling, spatial analysis, and three-dimensional prospectivity modeling. Spatial analysis revealed that the majority of gold ore bodies are situated near the main fault, with gold mineralization primarily occurring within a spatial range of approximately -80 meters to 20 meters from the main fault plane. This spatial distribution predominantly aligns in a SW-NE direction. Spatial characteristic extraction of fault slope indicators suggests that the slope angles are conducive to the migration and accumulation of ore-forming hydrothermal fluids, with ore body metal content rapidly increasing within an angle range of approximately 20° to 60°. The shape analysis of the mainfault indicates that the principal spaces of mineralization enrichment are within -10m to 20m of the fault plane undulations, where gold resources are concentrated in a relatively flat area. However, the degree of mineralization is more pronounced in the protruding sections than in the depressed areas. The areas with significant dip changes in faults display higher variations in orebody attitudes, with mineralization noticeably weaker in areas where the fault steepness changes markedly. Ore-bearing units exhibit significantly higher grades within the -17° to 3° interval of fault steepness transition. This interval also sees a rapid accumulation of gold resources. The Nibao gold mine's mineralization is derived from deep, ore-bearing hydrothermal fluids ascending along major fractures, precipitating, and accumulating in favorable ore-hosting spaces (faults, anticline cores) and lithological combinations (sedimentary tuffs, tuffs). Three deep potential gold targets were identified, highlighting the deep western edge of the F1 fault and the deep southeast-trending lower plate as prospective areas for future exploration. This study underscores the effectiveness of 3D prospective modeling as an indispensable tool for elucidating the spatial distribution of fault-controlled Carlin-type gold deposits and their tectonic determinants.

Both drag and lift forces impact an inclined plane when it is dragged through a granular bed. In this paper, the following results have been obtained: the drag and lift forces grow with the velocity of motion; when the immersion depth is constant, the inclination angle has no effect on drag force, however, the lift force increases linearly with this inclination angle; the ratio of drag and lift forces is exactly equal to the tangent value of the inclined angle. In order to describe this physical process macroscopically, a continuum wedge model based on the Coulomb model is established to predict drag and lift forces. Particularly，the dynamic friction angle in the assumed shear band is predicted as a function of both inclined angle and moving velocity.

This study was first time designed to investigate the effect of oxidation on protein digestion and transport properties in boiled sea cucumber body wall (BSCBW) via simulated digestion combine with everted-rat-gut-sac models. Boiling heat treatments led to protein oxidation in SCBW, manifested by increases in free radical intensity, thiobarbituric acid reactive substances, carbonyl groups, disulfide bonds, dityrosine bonds, advanced glycation end products, protein hydrophobicity and aggregation, declines in free sulfhydryl group, and secondary structure transition from α-helix to β-sheet. Boiling for 2 h caused the anti-digestion collagen unfolding, provided the action site for protease, and improved the protein digestion and transport levels. On the contrary, excessive oxidative modification of 4 h-BSCBW resulted in decreased protein digestion and transport levels. From the perspective of texture, digestion and transport properties, boiling for 2 h can obtain sea cucumber products with better edible and digestible properties, which is considered to be a better processing condition.

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

Current numerical methods for simulating biophysical processes in aquatic environments are typically constructed in a grid-based Eulerian framework or as an individual-based model in a particle-based Lagrangian framework. Often, the biogeochemical processes and physical (hydrodynamic) processes occur at different time and space scales, and changes in biological processes do not affect the hydrodynamic conditions. Therefore, it is possible to develop an alternative strategy to grid-based approaches for linking hydrodynamic and biogeochemical models that can significantly improve computational efficiency for this type of linked biophysical model. In this work, we utilize a new technique which links hydrodynamic effects and biological processes through a property-carrying particle model (PCPM) in a Lagrangian/Eulerian framework. The model is tested in idealized cases and its utility is demonstrated in a practical application to Sandusky Bay. Results show the integration of Lagrangian and Eulerian approaches allows for a natural coupling of mass transport (represented by particle movements and random walk) and biological processes in water columns which is described by a nutrient-phytoplankton-zooplankton-detritus (NPZD) biological model. This method is far more efficient than traditional tracer based Eulerian biophysical models for 3-D simulation, particularly for a large domain and/or ensemble simulations.

As a manifestation of technological innovation achievements, patents reflect the frontier of technological development in the field. This paper constructs a multi-entity patent collaboration network and analyzes its evolution patterns to provide a reference for innovation organizations to grasp the general direction of innovation development and select partners. Based on the data of collaboration patents of two and three organizations in China's new energy vehicles (NEV) industry from 2008 to 2021, this paper constructs higher-order interaction collaboration innovation networks in different periods to analyze the spatial evolution of networks and patent cooperation activities. The results show that the generalized degree distribution of nodes and edges conforms to the power-law distribution. The two-dimensional simplex networks gradually form triangle groups centered on the core nodes, and the importance of key edges is beginning to emerge. Key organizations and partners, including State Grid Corporation of China, Tsinghua University, and China Electric Power Research Institute, will largely determine the direction for the future development of cooperation innovation. The study also reveals that Beijing, Jiangsu, Zhejiang, Guangzhou, and Shanghai are in central positions in the cooperative innovation network, based on their cooperation breadth and depth measures. Additionally, key links formed by Beijing as hubs are not only the center of information exchange but also function as bridges that connect to other regions.

Zero-rate output (ZRO) drift induces deteriorated micro-electromechanical system (MEMS) gy-roscope performances, severely limiting its practical applications. Hence, it is vital to explore an effective method toward ZRO drift reduction. In this work, we conduct an elaborate investigation on the impacts of the internal and packaging stresses on the ZRO drift at the thermal start-up stage, and propose a temperature-induced stress release method to reduce the duration and magnitude of ZRO drift. Self-developed high-Q dual mass tuning fork gyroscopes (TFGs) are adopted to study the correlations between temperature, frequency and ZRO drift. Furthermore, a rigorous finite element simulation model is built based on the actual device and packaging structure, revealing the temperature and stresses distribution inside TFGs. Meanwhile, the relationship between temperature and stresses are deeply explored. Moreover, we introduce a temperature-induced stress release process to generate thermal stresses and reduce the temperature-related device sensitivity. By this way, the ZRO drift duration is drastically reduced from ~2000 s to ~890 s, and the drift magnitude decreases from ~0.4 °/s to ~0.23 °/s. This stress release method achieves a small bias instability (BI) of 7.903 °/h and a low angle random walk (ARW) of 0.792 °/√h, and the long-term bias performance is significantly improved.

Perovskite based solar cells have achieved tremendous progress reaching record efficiency in the past 5 years. Numerous new processes and chemistry have been reported and contribute to the perovskite rapid progress. Continuous efficiency improvements are still necessary for perovskite solar cells, and an exploratory data analysis on devices performance over multiple studies could boost the technology development. Such analysis could identify patterns or provide insights that are not obvious in a single study. Here we present a high quality dataset containing only independently certified Pb-based perovskite solar cells summarizing their efficiency, relevant I-V metrics, manufacturing processes and materials used. Analysis over the dataset provides insights on how aperture size, perovskite deposition methods and materials used in each functional layer affect the final solar cell efficiency and I-V metrics. Future directions are also suggested for efficiency improvements.

The snap fit is a common mechanical mechanism. We have studied the spherical snap fit carefully for its physical asymmetry which is easy to assemble but difficult to disassemble, and obtained the general law.Because of the complexity of spherical structure, it is difficult to get a theoretical formula to describe its physical asymmetry.In this paper, through the method of combining theory, simulation and experiment, and based on the general rule of cylindrical snap fit obtained in the early stage, pushing assembly and pulling disassembly of spherical snap fit are studied,we not only get the theoretical formula of spherical snap fit, but also further verify the correctness of previous research conclusions on cylindrical snap fit.This research provides strong theoretical support and basis for the optimization design and further research of snap fit.

Inflammatory reaction after ischemia-reperfusion contributes significantly to prognosis, and microglia activation is the main resource of inflammation in nervous system. STAT5 is proving to be a highly effective anti-inflammatory therapy with great potential, and inhibition of STAT5 has demonstrated significant anti-inflammation and therapeutic effects, but rarely focus on mechanism of neuroinflammation and brain injury from ischemia-reperfusion. It is the first time to found that the anti-inflammation of dauricine is mainly through STAT5-NF-κB pathway, might act as a STAT5 inhibitor. Dauricine suppressed the inflammation cytokines Eotaxin, KC, TNF-α, IL-1α, IL-1β, IL-6, IL-12β, IL-17α, and also inhibited the microglia activation. STAT5b mutant at Tyr-699 reversed the protective effect of dauricine on oxygen-glucose deprivation-reperfusion injury of neurons, and reactivated the suppression of dauricine on P-NF-κB of microglia. These results suggest that dauricine might suppress the neuroinflammation and protect the neuron from the injury of post-ischemia-reperfusion via mediating the microglia activation through STAT5-NF-κB pathway, and ss a potential therapeutic target for neuroinflammation, STAT5 needs to be raised concern in ischemic stroke.

There are four subtypes of adenosine receptors (ARs), named A1, A2A, A2B and A3, all of which are G protein-coupled receptors. The A2BAR, coupled to both Gαi and Gαq G proteins, is one of the several G-protein-coupled receptors that are expressed in a significantly higher level in some cancer tissues in comparison to adjacent normal tissues. There is growing evidence that the A2BAR plays an important role in tumor cell proliferation, angiogenesis, metastasis, and immune suppression. Thus, A2BAR antagonists are potentially novel attractive anticancer agents. Several antagonists targeting at the A2BAR are currently in clinical trials for various types of cancers. In this review, we first describe the signaling, agonists, and antagonists of the A2BAR. We further discuss the role of the A2BAR in the progression of various types cancers, and the rationale of using A2BAR antagonists in cancer therapy

In the paper, the authors survey integral representations of the Catalan numbers and the Catalan–Qi function, discuss equivalent relations between these integral representations, supply alternative and new proofs of several integral representations, collect applications of some integral representations, and present sums of several power series whose coefficients involve the Catalan numbers.

The nuclear reactor measurement system is a crucial component of the nuclear measurement system in a nuclear power plant. Its primary function is to measure the power distribution within the reactor core using detectors, calibrate, and provide data on core fuel consumption. Therefore, the study of the detectors' reliability is crucial for ensuring the safe operation of the nuclear power system. The article describes the operational mechanism of the gas ionization chamber detector utilized in the intermediate-range detector of the off-board nuclear measurement system. It also analyzes the movement of particles between the plates during the ionization process of the nuclear reaction taking place in the detector. The functional relationship between the current in the recombination region and the ionization region involved in the actual working condition, and the change with the increase of voltage between the plates, is deduced. A mathematical model is established for the number of pulses generated between the plates and the magnitude of the voltage between the plates. Subsequently, the change in the offset of the voltage corresponding to the inflection point of the ping curve and the change rule of the slope of the ping curve are investigated. Combined with the analysis of experimental data, the results show that the initial particle energy of Ar+, the primary sensitive particle on the detector surface, follows a normal distribution and is influenced by the energy loss associated with the initial velocity and the voltage between the plates. The trends of the inflection points and slopes of the ping curves can be utilized to evaluate the performance and operational status of the detector. Combined with the results of the experimental data analysis, the fit is good, and the inflection point currents in the normal state decrease by about 1.5% annually. The intelligent diagnostic system, based on the method studied in this paper, has been successfully implemented in the RPN digital retrofit and upgrade project at Qinshan No. 2 Plant.

Snap fit is a common mechanical mechanism. It uses the physical asymmetry that is easy to assemble but difficult to disassemble to provide a simple and fast link between objects. The ingenious combination of geometric shape, bending elasticity and friction of the snap fit is the mechanism behind the easy to assemble but difficult to disassemble disassemble. Yoshida and Wada (2020) has done a groundbreaking work in the analysis of the elastic snap fit. During our study of their paper, while we really enjoyed their research, unfortunately we detected several questioning formulations. After careful checking, we found that those formulations are not typographical, therefore it is necessary to make corrections. This paper reformulates the linear elasticity of a cylindrical snap fit, obtains an exact solution and proposes an accurate relation between the opening angle and bending tangent angle. Under the first order approximation, our formulations can reduced to the results of Yoshida and Wada and hence confirms the scientific correctness of Yoshida and Wada's work. Furthermore, this paper also derives a correct vertical displacement expression, and propose a new way of disassembly by bending for the first time and formulate a scaling law by data fitting. All formulations are validated by finite element simulation and experiment. The research here is helpful to the design of elastic snap fit or adjustable mechanical mechanism and metamaterial cell.

In the case of a Cu-Mo-W polymetallic ore, the wastewater from the scheelite cleaning flowsheet contains large amounts of residual flocculants and metal ions, and the separation of chalcopyrite and molybdenite require a large number of environmentally harmful depressants. Therefore, it is necessary to find new methods to reduce the environmental and cost pressures of wastewater treatment and the use of depressants. In this work, the flotation wastewater from scheelite cleaning flowsheet for the separation of chalcopyrite and molybdenite by selective surface passivation was investigated for the first time. Flotations of single minerals and artificially mixed minerals with or without immersion pretreatment in the presence and absence of aeration were performed. The results showed that pulp pH had no effect on the flotation of either mineral, and a molybdenite recovery of 93.22% with chalcopyrite recovery of 10.77% was achieved under the conditions of 10 days of immersion pretreatment with aeration, 350 mg/L of kerosene, and 100 mg/L of MIBC. By combining the electrochemical cyclic voltammetry analysis and characterization by XRD and SEM, the selective surface passivation mechanism of chalcopyrite was discussed, which could be due to the coverage of the insoluble oxidation products, especially jarosite. This work has simultaneously achieved the depressant-free flotation separation of molybdenite and chalcopyrite and the reuse of scheelite flotation wastewater, which is of great significance for environmental protection and cost saving.

In this study, in order to explore the failure mode of ZnO varistors under multiple lightning stroke, a 5-pulse 8/20 μs nominal lightning current with pulse intervals of 50 ms was applied to the ZnO varistors. Scanning electron microscopy (SEM) and X-ray diffractometry (XRD) were used to analyze the microstructure of the material. The failure processes of ZnO varistors caused by multiple lightning impulse current were described. The performance changes of ZnO varistors after multiple lightning impulses were analyzed from macro and micro perspectives. According to the results of this study’s experiments, the macroscopic failure mode of the ZnO varistors after multiple lightning impulse was that the electrical parameters deteriorate rapidly with the increase of the number of impulse groups, and finally destroyed by side-corner cracking. The microstructural examination indicated that after the multiple lightning strokes, the proportion of Bi in the several crystal phases had been converted, the grain size of ZnO varistors became smaller, and the white intergranular phase (Bi-rich grain boundary layer) increased significantly. The failure mechanism was thermal damage and grain boundary structure damage caused by temperature gradient thermal stress generated by multiple lightning current.

In the paper, the authors find two explicit formulas and recover a recursive formula for the generalized Motzkin numbers. Consequently, the authors deduce two explicit formulas and a recursive formula for the Motzkin numbers, the Catalan numbers, and the restricted hexagonal numbers respectively.

The two-scale method (TSM) is an effective approach to simulate electromagnetic (EM) scattering from rough sea surface, to interpret physical interaction of EM wave with rough sea surfaces. The sea surface roughness spectrum and the cutoff wavenumber are two key factors affecting the accuracy of TSM simulation. This paper takes the geophysical model functions (GMFs) of different band as reference, and quantitatively studies the two factors based on the numerical simulation of different polarization backscattering coefficients. The numerical simulation demonstrates that Apel spectrum is more suitable for the backscattering simulation in C/X/Ku-band, and the optimal cutoff wavenumbers are also derived for TSM simulation of EM scattering in C/X/Ku-band. Then an empirical model function of optimal cutoff wavenumbers with respect to frequency, incident angle and wind speed are obtained with regression method. Finally, the simulation results with the new model function of cutoff wavenumber are compared with the GMF and measured data in different bands and they are all consistent. Moreover, a physical explanation for the optimal cutoff wavenumber is also given.

Twining stems are an important form of plant stems. Twining stems can exhibit two different chiralities: right-handed and left-handed, with right-handed twining stems being much more common than left-handed ones. The determination of chirality in twining stems has always been a fascinating topic. Many people believe that the direction of twining stems in a given species is fixed, but this is not the case. Some species have twining stems that exhibit both chirality types, i.e. the chirality is variable. Moreover, such species or genera are not rare and can be commonly encountered in everyday life. Here, we report the presence of variable-chirality twining stems (VCTS) in several species or genera within the Asteraceae, Campanulaceae, Rubiaceae, Lamiaceae, Polygonaceae, Santalaceae, and Ranunculaceae families, including common plants such as Mikania micrantha and Pleuropterus multiflorus. VCTS is an objectively existing phenomenon, but often overlooked. Understanding and accepting this concept will greatly assist future research in this field.

Prior studies have focused on the overall behavior of randomly moving particle swarms. However, the characteristics of the stochastic-constrained particles that form ubiquitously within these swarms remain oblivious. This study demonstrates a generalized diffusion equation for stochastic-constrained particles that considers the velocity and location aggregation effects observed from their parent particle swarm (i.e., a completely random particle swarm). This equation can be approximated as the form of Schr\"odinger equation in the microcosmic case (low relative density) and describe the dynamics of the total mass distribution in the macrocosmic case (high relative density). The predicted density distribution of the particle swarm in the stable aggregation state is consistent with the total mass distribution of massive, relaxed galaxy clusters (at least in the range of r < r_s), preventing cuspy problems in the empirical Navarro-Frenk-White (NFW) profile. This study opens a window to observe the dynamics of stochastic-constrained particles from a third perspective, from which the aggregation effect of particles without gravitation can be saw.

Red plum apricot is the best apricot over the world. Since having been introduced into Guyuan county in 1987 from Shaanxi province, red plum apricot grows well and then has been selected as good varieties to popularize in semirid loess hilly regions because the color of red plum apricot is beautiful, aroma fragrant , and taste is the mix of sour and sweet and nutrition is rich. Since 1995, the yield, benefits and planting area of red plum apricot increase doubly, and the distribution range of red plum apricot increased from Guyuan to the whole Ningxia, and then to Gansu province and so on in the water-limited regions, China. However, there are still some problems in the sustainable produce of red plum apricot. In order to promote the development of red plum apricot and meet people's increasing demand, we should do intensive study of the relationship between red plum apricot and environment and the comparison of possible methods to reduce the bad influence of drought, low temperature and frost on quality and production of red plum apricot, and determine the soil water resources use limit by red plum apricot and the suitable leaf amount of red plum apricot when the planting density equal soil water carrying capacity for red plum apricot and select the best method to reduce or evade the bad influence of soil drought, low temperature, frost and soil drought on red plum apricot to ensure the sustainable produce of red plum apricot in Sustainable Produce of red plum apricot in water-limited regions.

The Rybczynski theorem describes the trade effect within production analyses between factor endowments and outputs. The Stolper-Samuelson theorem focuses on cost analyses between factor reward and commodity price. This paper examines the trade effect of changes of factor endowments on prices, based on general equilibrium. The study shows that changes of factor endowments cause domestic output changes (the Rybczynski effect), which affect output prices and factor prices (the Stolper-Samuelson effect). It is like a chain of effects that the Rybczynski’s trade effect triggers the Stolper-Samuelson’s trade effect. The analysis of this paper shows that a small increase of a factor endowment of any country rewards another factor and the commodity using the latter factor intensively. It displays a tuneful circle. Trade brings a well-balanced development to the world.

The common dandelion uses a bundle of drag-enhancing bristles (the pappus) that enables seed dispersal over formidable distances; however, the scaling laws of aerodynamic drag underpinning pappus-mediated flight remains unresolved. In this paper, we study the aerodynamic shape of dandelion, derive the scaling law of resistance, determine the Vogel exponent. In particular, we find that the total drag coefficient is proportional to the -2/3 power of the dandelion pappus Reynolds number, and obtain the terminal velocity of the dandelion seed under gravitation field.

This study utilises NaOH to treat composite cementitious materials containing aeolian sand and zeolite powders, which were used to replace 50% of the cement in aeolian-sand concrete (ASC). The mechanical properties of treated ASC considerably improved, especially when the NaOH dosage was 4% by mass. After curing this sample (denoted as AAZC-4) for 28 d, its compressive strength improved by 17.2% and its split tensile was increased by 16.3%. Potassium feldspar and montmorillonite in zeolite powder and SiO2 in the sand were decomposed by OH− and combined with other elements to generate various silicate gels and A-type potassium zeolite crystals inside the concrete. Microscopic examination showed that the gels and crystals intertwined to fill the pores, decreasing (increasing) the percentage of large (small) pores, thus optimising the pore structure. This substantially improved the mechanical properties of ASC. Freeze–thaw salt-intrusion tests showed that the extent of mass loss, degree of damage and loss of compressive strength of AAZC-4 were similar to those of ordinary concrete but were reduced by 36.8%, 19% and 52.1%, respectively, compared with those of ASC. Therefore, AAZC-4 has sustainable working performance in the chloride ion permeable environment in cold and arid areas.

The performance of the absolute atom gravimeters used on moving platforms, such as vehicles, ships and aircrafts, is strongly affected by the vibration noise. To suppress its influence, we summarize a vibration compensation method utilizing data measured by a classical accelerometer. The measurements with the accelerometer show that the vibration noise in the vehicle can be 2 order of magnitude greater than that in the lab during daytime, and can induce an interferometric phase fluctuation with a standard deviation of 16.70π. With the compensation method, our vehicle-mounted atom gravimeter can work normally in these harsh conditions. Comparing the Allan standard deviations before and after the vibration noise correction, we find a suppression factor of 22.74 can be achieved in static condition with an interrogation time of T = 20 ms, resulting a sensitivity of 1.35 mGal/Hz1/2, and a standard deviation of 0.5 mGal with an average time of 10 s. We also demonstrate the first test of an atom gravimeter in a moving vehicle, in which a suppression factor of 50.85 and a sensitivity of 60.88 mGal/Hz1/2 were realized with T = 5 ms.

Predicting and evaluating the vitality level of public spaces of urban design is crucial before new construction and renewal, especially for developing countries, to avoid failures like "ghost neighborhood" and reduce resource waste. However, existing assessment methods for the urban vitality are either static and ignore changes in the time dimension, or rely on historical big data and are unable to predict unbuilt projects. This study combines previous methods and crowds’ characteristics observation in public space, puts forward the crowd-frequency hypothesis and constructs an algorithm, and establishes a time-dimensional urban vitality dynamic prediction model. Taking the Rundle Mall neighborhood in Adelaide, Australia, as an example, the effec-tiveness of the prediction model was proved through on-site observation sampling comparative verification method. In addition, the decision tree model was used to conduct machine learning on the case data, and a set of algorithm programs were obtained that can directly input some basic information to obtain the urban vitality level (high-medium-low) in a certain period. It can be used as a tool to support the design and decision-making processes of urban planners and government officials, providing a low-cost way to achieve sustainable urban vitality construction of late-developing cities directly.

The study of a flexible body immersed in a flowing medium is one of best way to find its aerodynamic shape. This Letter revisited the problem first studied by Alben, Shelley and Zhang (Nature 420, 479-481, 2002). The aerodynamic shape of the fibre is found by simpler approach and universal drag scaling laws of the flexible fibre in flowing medium are proposed by using dimensional analysis. The Alben scaling laws is being generalized and confirmed to be universal. Our study show that the Alben number is a measurement of maximum curvature of the fibre forced by dynamic pressure. A complete Maple code is provided for finding aerodynamic shape of the fibre in the flowing medium.

During choriogenesis in insects, chorion (eggshell) is formed by surrounding follicular epithelial cells in ovarioles. However, the regulatory endocrine factor(s) activating choriogenesis and the chemical components on eggshell deserve further exploration. In two representative Coleopterans, a Coccinellid Henosepilachna vigintioctopunctata and a Chrysomelid Leptinotarsa decemlineata, genes encoding the 20-hydroxyecdysone (20E) receptor heterodimer, ecdysone receptor (EcR) and ultraspiracle (USP), and two chitin biosynthesis enzymes UDP-N-acetylglucosamine pyrophosphorylase (UAP) and chitin synthase (ChS1), were highly expressed in ovaries of the young females. RNA interference (RNAi)-aided knockdown of either HvEcR or Hvusp in H. vigintioctopunctata inhibited oviposition, suppressed the expression of HvChS1, and lessened the positive signal of Calcofluor staining on the chorions, which suggests the reduction of a chitin-like substance (CLS) deposited on eggshells. Similarly, RNAi of LdEcR or Ldusp in L. decemlineata constrained oviposition, decreased the expression of LdUAP1 and LdChS1, and declined CLS contents in the resultant ovaries. Knockdown of LdUAP1 or LdChS1 caused similar defective phenotypes, i.e., reduced oviposition and CLS contents in the L. decemlineata ovaries. These results, for the first time, indicate that 20E signaling activates choriogenesis in two Coleopteran species. Moreover, our findings propose the deposition of a CLS on the chorions.

In the paper, the authors establish two identities to express the generating function of the Chebyshev polynomials of the second kind and its higher order derivatives in terms of the generating function and its derivatives each other, deduce an explicit formula and an identities for the Chebyshev polynomials of the second kind, derive the inverse of an integer, unit, and lower triangular matrix, present several identities of the Catalan numbers, and give some remarks on the closely related results including connections of the Catalan numbers respectively with the Chebyshev polynomials, the central Delannoy numbers, and the Fibonacci polynomials.

A highly efficient reduction process of Cr (VI) with biochar was conducted in this paper. The results showed that nearly 100% Cr (VI) was reduced at selected reaction conditions: the dosage of biochar at m (C)/m(Cr) = 3.0, reaction temperature of 90 ℃, reaction time at 60 min and concentration of H2SO4 of 20 g/L, respectively. The reduction kinetics analysis demonstrated that the reduction of Cr (VI) fitted well with the pseudo-first-order model and the apparent activation energy was calculated to 40.24 kJ/mol. Response surface methodology confirmed that all the experimental parameters had positive effect on the reduction of Cr (VI). The influence of each parameter on the reduction process followed the order: dosage of biochar> Concentration of H2SO4 > Reaction Temperature > Reaction Time. This paper provided a versatile strategy for treatment of wastewater containing Cr (VI) and showed a bright tomorrow for wastewater treatment.

Federated learning is an effective approach for preserving data privacy and security, enabling machine learning to occur in a distributed environment and promoting its development. However, an urgent problem that needs to be addressed is how to encourage active client participation in federated learning. The Shapley Value, a classical concept in cooperative game theory, has been utilized for data valuation in machine learning services. Nevertheless, existing numerical evaluation schemes based on the Shapley Value are impractical as they necessitate additional model training, leading to increased communication overhead. Moreover, participants’ data may exhibit Non-IID characteristics, posing a significant challenge to evaluating participant contributions. Non-IID data weakens the marginal effects of participants, which in turn affects model accuracy and leads to underestimated contribution measurements. Current works often overlook the impact of heterogeneity on model aggregation. This paper presents a fair federated learning contribution measurement scheme that addresses the need for additional model computations. By introducing a noval aggregation weight, it enhances the accuracy of contribution measurement. Experiments on the MNIST dataset show that the proposed method can accurately compute the contributions of participants. Compared to existing baseline algorithms, the model accuracy is significantly improved, with a similar time cost.

The current deformation and stable state of slopes with historical shatter signs is a concern for engineering construction. Suspected landslide scarps were discovered at the rear edge of the slope of the Genie in the Sichuan-Tibet transportation corridor during a field investigation. In order to qualitatively determine the current status of the surface deformation of this slope, this paper uses high-resolution optical remote sensing, airborne LiDAR and InSAR technologies for comprehensive analysis. The interpretation of high-resolution optical and airborne LiDAR data revealed that the rear edge of the slope exhibits three levels of scarps. However, no deformation was detected with the D-InSAR analysis of ALOS-1 radar images from 2007 to 2008 or with the Stacking-InSAR and SBAS-InSAR processing of Sentinel-1A radar images from 2017 to 2020. A geological model of the slope was established in combination with field investigation stipulating that the slope is composed of steep anti-dip layered dolomite limestone and that the scarps at the rear edge of the slope were caused by historical shallow toppling. Further research is recommended to determine the extent of toppling deformation and evaluate the slope stability under the disturbance of tunnel excavation.

Ammonium sulfate has been utilized in agriculture; however, there is a dearth of research on its application in maize cultivation subsequent to the implementation of nitrification inhibitors or coating. This study aims to analyze the impacts of various combinations of ammonium sulfate fertilizers on soil nutrients, plant nutrient uptake, yield, and fertilizer utilization efficiency in maize cultivation to ascertain the optimal and stabilized disposal method for ammonium sulfate. A completely randomized design was employed with five treatments (AU, the control using urea; AS, treatment using ammonium sulfate; ASN, treatment using ammonium sulfate with a nitrification inhibitor; ASG, treatment using oil-coated ammonium sulfate; ASD, treatment using oil-humic acid-coated ammonium sulfate). Results showed that: (1) Compared with AU and AS, ASN, ASG and ASD decreased the leaching rates of TN, NH4+-N and NO3-N to the 10-20 cm soil layer, and more residual N was obtained in 0-10 cm soil layer. The first-order kinetic equation Nt=N0(1-e-kt) can better fit the process of nitrogen accumulation and release, and the N release rate constant is AU>CK>AS>ASH>ASN>ASD; (2) Compared with AU and AS treatments, the plant dry weight, grain dry weight, spike width, spike length, and yields of maize increased by 8.85-11.08%, 12.98-14.15%, 2.95-3.52%, 5.50-5.65%, and 43.21-51.10% under ASG treatment respectively. The impact of effective spike number on maize yield was found to be significant, as demonstrated by the path analysis conducted in this study. Furthermore, the accumulation levels of nitrogen, phosphorus, and potassium within above-ground plants significantly increased under the ASG treatment compared to the AU and AS treatments. The partial productivity of nitrogen, phosphorus, and potassium increased by 1.43-1.51-fold under ASG treatment, while grain nitrogen balance, grain phosphorus balance, and grain potassium balance increased by 1.41-1.58-fold, 1.51-1.95-fold, and 1.15-l.96-fold respectively. The oil-coated ammonium sulfate, therefore, exhibited the optimal slow-release effect of nutrients, thereby achieving superior performance in enhancing maize production and efficiency.

Robotic systems have been widely used in various industries, so the security of communication between robots and their components has become an issue that needs to be focused on. As a framework for developing robotic systems, the security of ROS2 can directly affect the security of the upper-level robotic systems. Therefore, it is a worthwhile research topic to detect and analyze the security of ROS2. In this paper, we adopt a formal approach to analyze the security of the communication mechanism of ROS2. First, we use a state transition system to model the potential vulnerabilities of ROS2 based on the ROS2 communication mechanism and the basic process of penetration testing. Secondly, we introduce the CIA model on the basis of the established vulnerability model and use LTL to define its security properties. Then, we design and implement a vulnerability detection tool for ROS2 applications based on the vulnerability model and security properties. Finally, we experimentally test some ROS2-based applications, and the results show that ROS2 has vulnerabilities without additional protection safeguards.

A lignin modified salt resistance branched high-performance water reducer was prepared via free radical polymerization. The water reducing agent was identified through Fourier transform infrared analysis, thermal gravimetric analysis, and scanning electron microscopy. The experiment conducted on cement paste demonstrates that the water-reducing efficiency can reach a maximum of 44%. Additionally, the significant spatial steric hindrance of the application enhances the dispersal capability of the water-reducing agent, resulting in effective water reduction and reduced viscosity. In addition, its compressive strength is the highest after 3-day curing and 3, 7, 28-day standard curing, and it has the best overall performance both in water and saline water prepared systems.The application in oil cement slurry shows that it exhibits good dispersibility in fresh water, saline water, and substitute ocean water. In the Halfaya and Missan Oilfields of Iraq, BHPWR was used in slurry with a density of 2.28g cm-3 for casing the 244.5 mm salt paste layer of five wells. Cementing results exceeded expectations with over 85% excellent and 100% qualified.

The article delves into the intricate phase transitions of 1-Octadecanol and n-Nonadecane within a binary system, unveiling dynamic structural changes under varying conditions. Through Fouri-er-transform infrared (FTIR) analysis, specific molecular vibrations were identified, shedding light on the molecular composition and interactions. The study highlights the challenges in detecting subtle phase transitions and emphasizes the individuality of molecular behaviours in closely related compounds. The findings underscore the complexity of phase transitions in binary systems and advocate for a nuanced approach to studying molecular structures and behaviours. Addi-tionally, the research contributes valuable insights into the molecular dynamics of Organic Polymer Functional Adsorption Materials, offering implications for synthetic waxy layers in plant epidermis.

Vibro-fluidized dry coal beneficiation involves the unavoidable mixing of -1 mm coal dust into the fluidized bed, which compromises the stability and homogeneity of the bed density and reduces the effectiveness of fine-grained coal separation. In order to understand the features of coal powder separation and mixing (-1 mm) in a vibrating fluidized bed, as well as to achieve a uniform and stable bed density, a wide-grained dense medium consisting of -1 mm coal dust and 0.3-0.15 mm magnetite powder was homogeneously mixed in this work. The degree of density separation in the entire bed was examined, as well as the local mixing properties of the Wide-grained Dense Medium. It was discovered that when low vibrational energy was introduced at the same gas velocity, particle separation was enhanced in comparison to the usual fluidized bed. Little bubbles were found to ensnare fine coal dust and migrate upward, increasing density separation. The introduction of high vibrational energy leads to particle disorder within the bed and an increase in the level of particle mixing. The beneficial effects of vibration on the bed are diminished when the gas velocity is gradually increased under specified vibration circumstances. This causes big bubbles to develop more frequently, which increases particle mixing. Among them, the 1-0.5 mm fine-grained coal exhibits the best mixing state; it is less impacted by variations in air velocity and vibration levels, whereas the -0.5 mm coal dust is more affected by each of these variables. Furthermore, a wide range of air velocity regulation without a significant segregation state change was discovered to be achievable by the particle system under vibration circumstances of f=25Hz A=1mm and f=25Hz A=2mm.

Thirty-six healthy 21-day-old weaned ternary piglets (Duroc × Landrace × Yorkshire) were randomly divided into 2 treatments with 18 replicates per treatment and 1 pig per replicate. The control group was fed with basal diet and the test group was fed with diets supplemented with 1 kg/t tea residue. The test period was 28 days. The results are as follows: The addition of tea residue in the diet has no significant effect on the growth performance of weaned piglets (P > 0.05), but it could significantly reduce the diarrhea rate of piglets from 1 to 7 days and 1 to 28 days (P < 0.05). Compared with the control group, the dietary supplementation of tea residue had no significant effect on nutrient apparent digestibility, plasma biochemical indexes and plasma immune indexes (P > 0.05), but increased the content of glutathione in plasma (P < 0.05). Tea residue had no significant effect on the morphology of jejunum and ileum of piglets (P > 0.05), but it could significantly reduce the content of chloride ion in feces (P < 0.05). Compared with the basal diet group, there was no significant difference in the relative expression of TMEM16A and CFTR mRNA in the colon of weaned piglets (P > 0.05). The whole-cell patch clamp recording showed that the TMEM16A and CFTR ion channels could be activated by ionomycin and forskolin, respectively. However, when the HT-29 cells transfected with TMEM16A and CFTR channels were treated with tea residue extract, it could significantly inhibit the chloride current of the TMEM16A and CFTR ion channels (P < 0.05).

With the rapid development of global offshore wind power, the demand for offshore wind power operation and maintenance is also increasing. Wisdomization of offshore wind farms is a practical need to improve the operation level and benefit of offshore wind farms. This paper first introduces the current development situation and characteristics of global offshore wind power, and expounds the current situation and main challenges of offshore wind power operation and maintenance market. Therefore, our paper discusses the innovation of offshore wind power operation and maintenance from the aspects of operation and maintenance management of offshore wind power, monitoring and analysis technology of units, far-reaching wind field monitoring and operation and maintenance risks. Then, combined with information technology and lean management concept, a smart operation and maintenance management platform for wind farms in far-reaching sea areas is built to explore centralized and intelligent operation and maintenance management mode, improve operation and maintenance efficiency of wind farms in far-reaching sea areas, and minimize operation and maintenance costs. Finally, through the research on the characteristics of 5G technology, combined with the practical experience of operation and maintenance, and in view of the characteristics of offshore wind farms, we analyze and propose several typical application scenarios of 5G technology in the intelligent operation and maintenance of offshore wind farms, which provides a new solution for the efficient operation and maintenance of offshore wind farms.

The calculation and visualization of the dose field in the decommissioning of nuclear facilities is one of the important functions of the decommissioning virtual simulation system, which can provide accurate and intuitive radiation field distribution and play an important role in determining the demolition plan and protecting personnel during the engineering implementation process. This article investigates the development of dose field calculation and visualization in the reactor decommissioning virtual simulation systems, and preliminarily proposes a technical plan suitable for the development of the decommissioning dose field calculation and visualization display programs for the first Heavy Water Research Reactor (HWRR) in China. Besides, the applicability of the selected scheme is analyzed, the functional requirement and development direction of the HWRR reactor decommissioning dose field calculation and visual display module are preliminarily determined. Furthermore, the reactor vessel of HWRR reactor is modeled and the dose field distribution was calculated and visualized. This research can provide technical support for the development of the decommissioning simulation system for the first HWRR reactor in China.

For the last two decades, an increasing demand for low-cost adsorbents for drinking water treatment has been challenged in the rural areas of developing countries that have problems with arsenic (As) contamination. In this work, spent bleaching earth (SBE), a residual material that is formed during the process of refining vegetable oil, has been utilized to prepare the new magnetic adsorbent Fe-SBE/C by modifying its surface area through calcination and co-precipitation with iron. The experimental results demonstrate that Fe-SBE/C exhibits a substantial adsorption capacity towards both arsenite (As(III)) and arsenate (As(V)). Optimal pH conditions were found to be pH 10 for As(III) and pH 3 for As(V), resulting in adsorption percentages of 76.7% and 94.1%, respectively. Other experimental parameters such as calcination conditions, adsorbent dosage, iron-loading ratio, and the presence of co-existing ions were thoroughly investigated. The kinetic study revealed that the adsorption processes follow the Elovich and intraparticle diffusion models, suggesting a combined adsorption mechanism of boundary layer control and chemisorption. Furthermore, the isotherm followed the Langmuir model with a maximum adsorption capacity of 202.61 μg g-1 for As(III) and 187.61 μg g-1 for As(V). Through thermodynamic analysis and reinforcement by activation energy data, this research validates that the observed adsorption process is indicative through chemisorption. The regeneration study revealed the potential for multiple cycles of arsenic removal, highlighting the practical applicability of Fe-SBE/C in environmental contexts. In conclusion, the findings of this study underscore the efficacy of Fe-SBE/C in arsenic removal and present it as a promising and environmentally friendly solution for mitigating arsenic pollution.

The advancement in science and technology has led to luffa sponge (LS) being widely used as a natural material in industrial application as its polyporous structure and light texture. In order to enhance the utility of LS fibers as the reinforcement of lightweight composite materials, this study investigate its water absorption, mechanical properties, anatomical characteristic and thermal performance. Hence, moisture regain, tensile properties of LS fiber bundles were measured in accordance with standards and the structural characteristics were investigated via microscopic observation. Scanning electron microscopy (SEM) was used to observe the surface morphology and fracture surface of fiber bundles. Test results shows that the special structure where the phloem tissues degenerate to cavities had a significant influence on the mechanical properties of LS fiber bundles. Additionally, the transverse sectional area occupied by fibers in a fiber bundle (SF), wall thickness and ratio of wall to lumen of fiber cell, and crystallinity of cellulose had an impact on the mechanical properties of LS fiber bundles. Furthermore, the fiber bundles density of LS varies range of 385.46-468.70 kg/m³, much less than that of jute (1360.40 kg/m³) and Arenga engleri (950.20 kg/m³) while LS fiber bundles has superior specific modulus.

To reveal the antibacterial effect of wound secretions of different Chinese fir strains on five kinds of bacteria. Three 3-year-old seedlings of Taxus chinensis var.koraiensis and Yangkou and the 3-year-old container seedlings of Taxus chinensis var.pendula, Yang061 and Yang020, were used as the research objects. The antibacterial effect of wound secretions was determined by the filter paper diffusion method, and the antibacterial effect was analyzed. Results showed that the wound secretions of different strains of Chinese fir bark had noticeable bacteriostatic effects on Bacillus subtilis, Salmonella paratyphi B, Pseudomonas aeruginosa, Escherichia coli, and Staphylococcus aureus. However, the bacteriostatic effects of different strains of Chinese fir secretions differed. The minimum inhibitory concentrations (MICs) of the wound secretions of different strains of Chinese fir against the five test bacteria differed. The mean MIC of Pseudomonas aeruginosa was the highest, and the mean MIC of Escherichia coli was the lowest. The antibacterial ability of the wound secretions of different Chinese fir strains was mainly determined by the composition of the wound secretions. There was no noticeable relationship with the number of wound secretions.

With the economic recession and the deterioration of the ecological environment becoming more and more prominent in the world, the sustainable operation of enterprises is facing the most difficult choice in history. For each responsible enterprise, it is crucial to choose the market power expansive strategy that can improve the realistic viability or the technological innovation strategy that can improve the future development potential. This is of great significance to reduce the negative external effects of the corporate social environment and ensure their sustainable development. In this paper, we select the data of 18 large listed petrochemical companies from 2003 to 2018 as samples and construct a linear regression model for empirical analysis. Meanwhile, we put forward more practical business management strategies for the sustainable development of petrochemical enterprises in developing countries in further research.

Water quality retrieval for small urban waterbodies by remote sensing get used to be difficult due to coarse spatial resolution of the remote sensing imagery. The recently launched Sentinel-2 produces imagery with a spatial resolution of 10 m. It provides an opportunity to solve the problem of retrieving water quality for small waterbodies. Additionally, many water management issues also require fine resolution of imagery, e.g. illegal discharge to an urban waterbody. Since illegal discharges are an important issue for urban water management, chemical oxygen demand (COD), total phosphorous (TP), and total nitrogen (TN) were chosen as the target parameters for water quality retrieval in this study. COD, TP and TN, however, are non-optically active parameters. There were limited studies in the past to retrieve these parameters in comparison with optically active parameters, e.g. Chlorophyll-A etc. This study compared three machine learning models, namely Random Forest (RF), Support Vector Regression (SVR), and Neural Networks (NN), to investigate the opportunity to retrieve the above non-optically active parameters. Results showed that R² of TP, TN, and COD by NN, RF and SVR were 0.94, 0.88, and 0.86, respectively. The performances of water quality retrieval for these non-optically active parameters were significantly improved by the optimized machine learning models. These models hence solved the problem to use remote sensing data to retrieve these non-optically active water quality parameters and provided a new monitoring strategy for small waterbodies. Water quality mapping obtained by Sentinel-2 imagery provided a full spatial coverage of the water quality characterization for the entire water surface. Compared with water samples collecting and testing, it greatly reduced labor cost, reagents cost, and waste treatment cost. It also may help identify illegal discharges to urban waterbodies. The method developed in this research provides a new practical and efficient water quality monitoring strategy in managing water with consideration of environmental sustainability.

In the paper, the authors establish two identities, which can be regarded as nonlinear differential equations, for the generating function of Eulerian polynomials, find two identities for the Stirling numbers of the second kind, and present two identities for Eulerian polynomials and higher order Eulerian polynomials, pose two open problems about summability of two finite sums involving the Stirling numbers of the second kind. Some of these conclusions meaningfully and significantly simplify several known results.

In this study, Brillouin optical time-domain analysis (BOTDA) sensing technology was utilized for monitoring settlement in a similarity model of a highway subgrade. As contact winding cannot be used for an optical fiber that is buried directly in soil, uncoupling between. the fiber and the soil can occur. Thus, an optical-fiber-embedded beam (OFEB) was developed, and a method for measuring and calculating the beam deformation was proposed. A calibration test and a test on a similarity model of a subgrade were carried out to investigate the applicability and monitoring accuracy of the OFEB. It was concluded that the OFEB can accurately measure beam deflection, where the maximum relative error between measurements by the optical fiber and a displacement transducer was approximately 5%. The OFEB was embedded directly into a similarity model of a subgrade to monitor settlement. The deflection deformation of the OFEB was found to be close to the subgrade settlement over a certain settlement range with a relative error below 8.1%. Thus, the OFEB can be used to realize measure large-range distributed settlement in a subgrade. A numerical simulation was performed to identify appropriate beam dimensions and material design parameters, thereby extending the measurement range before decoupling of the OFEB and soil occurs. The enhancement of the measurement range and accuracy of the OFEB based on the preliminary experiments carried out in this study enables further investigation of settlement monitoring.

In this paper we provide a highly selected review and synthesis on some of the recent and notable contribution to research in portfolio analysis. A unique perspective on this development in the literature is offered in this paper by judiciously identifying a few sample eigenvalues adjustment patterns in a portfolio that leads to an improvement in the out-of-sample portfolio Sharpe ratio when the population covariance matrix admits a high-dimensional factor model. These patterns unveil a key insight into a portfolio performance improvement and shed an important light on the effectiveness of a few recently introduced ”robust to estimation errors” covariance matrix estimation approaches, which were not originally designed with the goal to improve the out-of-sample portfolio performance.

Tuning fork gyroscopes (TFGs) are promising for potential high-precision applications. This work proposes and experimentally demonstrates a novel high-Q dual mass tuning fork microelectro-mechanical system (MEMS) gyroscope utilizing three-dimensional (3D) packaging techniques. Except for two symmetrically-decoupled proof masses (PM) with synchronization structures, a symmetrically-decoupled lever structure is designed to force the antiparallel, antiphase drive-mode motion and basically eliminate the low-frequency spurious modes. The thermoelastic damping (TED) and anchor loss are greatly reduced by the linearly-coupled, momentum- and torque-balanced antiphase sense mode. Besides, a novel 3D packaging technique is used to realize high Q-factors. A composite substrate encapsulation cap, fabricated by through-silicon-via (TSV) and glass-in-silicon (GIS) reflow processes, is anodically bonded to the sensing structures at wafer scales. A self-developed control circuit is adopted to realize loop control and characterize gyro-scope performances. It is shown that a high-reliability electrical connection together with a high-air-impermeability package can be fulfilled with this 3D packaging technique. Furthermore, the Q-factors of the drive and sense modes reach up to 51947 and 49249, respectively. This TFG realizes a wide measurement range of ±1800° /s and a high resolution of 0.1° /s with a scale-factor nonlinearity 720 ppm after automatic mode-matching. Besides, the long-term zero-rate output (ZRO) drift can be effectively suppressed by temperature compensation, inducing a small angle random walk (ARW) of 0.923°/√h and a low bias instability (BI) of 9.270°/h.

Two new dimacrolide sesquiterpene pyridine alkaloids (DMSPAs), dimacroregelines A (1) and B (2), were isolated from the stems of Tripterygium regelii. The structures of both compounds were characterized by extensive 1D and 2D NMR spectroscopic analyses, as well as HRESIMS data. Compounds 1 and 2 are two rare DMSPAs possessing unique 2-(3′-carboxybutyl)-3-furanoic acid units forming the second macrocyclic ring, representing the first example of DMSPAs bearing an extra furan ring in their second macrocyclic ring system. Compound 2 showed inhibitory effects on the proliferation of human rheumatoid arthritis synovial fibroblast cell (MH7A) at a concentration of 20 μM.

The process of rainfall interception by tree organs is crucial in mitigating the impact of intense rainfall on urban drainage systems, particularly in the context of climate change. this study selected ten commonly found tree species in Shanghai. Main parts of trees, including leaves, branches, and bark, were collected to analyze their ability to intercept rainwater. The optimized Artificial Rainfall Simulation System (ARSS) was applied to simulate the rainfall. The time-changing process of rainwater interception in three organs was measured during a 180-minute rainfall event which under four different rainfall intensities (4, 8, 12, and 16 mm/h, respectively). Process models of rainwater interception in different organs were fitted with adsorption kinetic equations. The rainwater interception process of tree organs complied with the quasi 2nd-order adsorption kinetic equation. The rainwater interception capacity of leaves, branches, and bark of ten urban tree species ranged from 0.05 to 0.34 mm, 0.13 to 0.24 mm, and 0.29 to 1.22 mm, respectively. The rainwater interception capacity of three organs significantly differs (p&lt;0.05). It reveals that bark exhibits the highest rainwater interception ability. Coniferous tree species have a greater ability to intercept rainwater than broad-leaved tree species. There are also differences in the rainwater interception ability of trees in urban and natural areas.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

To study the heat and mass transfer characteristics of an evaporative cooler for cooling high-temperature working fluids such as supercritical carbon dioxide, an experimental device of the evaporative cooler was built, and a corresponding test system was constructed. Then, the experimental study was carried out based on the orthogonal test method, and the law and extent of the influence of water flow in the tube, spray water flow rate, inlet water temperature in the tube, and air flow rate on heat dissipation, cooling efficiency, and heat and mass transfer coefficients have been obtained. The correlation equations of the heat and mass transfer coefficients were obtained by fitting the orthogonal experimental data, and the validity of the correlation equations was confirmed by the verification experiment.

This study aimed to explore what factors affect teachers’ acceptance and instructional use of ICT in Chinese higher vocational colleges. Grounded in the modified UTAUT model, the current study investigated the direct and indirect effects of teachers’ performance expectancy, effort expectancy, external conditions, and behavioral intentions on using ICT in teaching. A total of 6087 teachers from 219 vocational colleges in 28 provinces in China participated in a large-scale survey. Structural equation modeling revealed that the teachers’ psychological perceptions (including performance expectancy, effort expectancy, and intention to use ICT technology) and the external support conditions (including professional development support, infrastructures, the climate of organizational reform and innovation, and teacher performance assessment mechanisms) significantly directly affect the use of ICT in Chinese higher vocational college teachers’ teaching practice. Moreover, this study confirmed the mediating role of teachers’ intention to use ICT in teaching in the relationship between teachers’ psychological perceptions and ICT instructional usage behavior. However, there were differences in the significance of these variables in the chain effect of teachers’ intention to use ICT. These findings expand our understanding of the factors influencing ICT use in teaching among VET teachers in China and thus provide practical implications for higher vocational college managers to promote teachers’ ICT teaching behaviors.

Currently, efficient utilization of low-grade thermal energy is a great challenge. Thermoelectricity is an extremely promising method of generating electrical energy from temperature differences. As a promising energy conversion technology, thermo-electrochemical cells (TECs) have attracted much attention in recent years for their ability to convert thermal energy directly into electricity with high thermal power. Within TECs, anions and cations gain and lose electrons, respectively at the electrodes using the potential difference between the hot and cold terminals of the electrodes by redox couples. Additionally, the anions and cations therein are constantly circulating and mobile via concentration diffusion and thermal diffusion, providing an uninterrupted supply of power to the exterior. This review article focuses mainly on the operation of TECs, recent ad-vances in redox couples, electrolytes, and electrodes. The outlook for optimization strategies re-garding TECs is also presented in this paper.

Fractures of the talar neck and body are associated with spine fractures and scoliosis deformity, which affect cosmetic appearance and cause difficulty in ambulation. The implant design for talus surgery is thriving as a functional alternative in case of severe talar destruction, focusing on segmentation and reconstruction of the talus’s shape. However, manual segmentation of the talus is time-consuming and subjective. In this study we exploited the automatic segmentation framework to efficiently train a deep learning-based model to accurately segment the talus based on computed tomography imaging. We developed three model configurations with nnU-Net and investigated their Dice similarity coefficients (DSC) and 95% Hausdorff distances (HD95) for talus segmentation on a CT image dataset. The three configurations performed well (DSC > 0.95, HD95 < 0.6). When tested on the same samples, one of the configurations was more efficient while ensuring higher accuracy. We propose to focus on talus anatomic variations with increasing age based on this framework and apply it to clinical trials at the next stage.

In this paper, we propose a new mathematical model based on the association between susceptible and recovered individual, where the association between susceptible and recovered individual is disturbed by white noise. This model is based on demographic changes and is used for long term behavior. We study the stability of equilibria of the deterministic model and prove the conditions for the extinction of diseases. Then, we investigate and obtain the critical condition of the stochastic epidemic model for the extinction and the permanence in mean of the disease with the white noise. To verify our results, we present some numerical simulations for real data related to disease.

In the process of sustainable development in the future, human society faces problems such as severe population load, economic transition, and lack of educational measures. One of the root causes of these problems is the shortage of innovative talents. Therefore, how to cultivate learners with multi-disciplinary integration and innovation ability is the key point that should be paid attention to in promoting the concept of quality education and coping with the future sustainable development process. This paper uses questionnaire survey method and literature analysis method to analyze the development of many educational institutions with STEAM concept as the core in China since 2017. It is found that the existing STEAM educational institutions generally have the following problems: the lack of team composition、difficulty in independent research and development、single course content and insufficient validation of course effectiveness. In order to more effectively promote the sustainable development of China's future course, STEAM education institutions should focus on strengthening the following development strategy: gradient team building, continuous independent research and development, cutting-edge projects curriculum transformation mechanism and multi-angle course effectiveness verification.

Two-dimensional (2D) bismuth oxyhalides (BiOX) have attracted much attention as potential optoelectronic materials. Expecting for their application diversity, we herewith systematically investigate the tunable properties of 2D BiOX by using first principles calculations. Their electronic and optical properties can be modulated by changing the number of monolayers, applying strain, and/or varying the halogen composition. The bandgap shrinks monotonically and approaches the bulk value, the optical absorption coefficient increases, and the absorption spectrum redshifts, as the layer number of 2D BiOX increases. Carrier transport property can be improved by applying tensile strain, and the ability of photocatalytic hydrogen evolution can be obtained by applying compressive strain. General strain engineering will be effective in linearly tune the bandgap of BiOX in a wide strain range. Strain together with halogen composition variation can tune the optical absorption spectrum to be on demand in the range from visible to ultraviolet. It suggests that that 2D BiOX materials have potential serving as tunable novel photodetectors, can be used to improve clean energy techniques, and are prospective in the field of flexible optoelectronics.

Aim: This study aimed to investigate the association between periampullary diverticulum (PAD) and difficult biliary cannulation, as well as to evaluate the impact of different types of PAD on the cannulation success rate and adverse events. Methods: A total of 636 patients who underwent endoscopic retrograde cholangiopancreatography (ERCP) during the study period were prospectively studied and divided into two groups based on the presence or absence of PAD. In group A, 126 patients had PAD compared with 510 patients in group B without PAD. The primary outcome measurements were ERCP procedures time, selective cannulation techniques, and cannulation difficulty in addition to cannulation success rate and ERCP-related adverse events. The difficult cannulation was analyzed using logistic regression considering age, co-morbidities, the presence of PAD types, and indications as independent factors. Results: The average cohort age was 65.30±16.67 years, and 52.7% were male. Significant higher rates of choledocholithiasis, cholangitis, and biliary pancreatitis were reported in the group of PAD (p<0.05). Successful selective cannulation was achieved in 97.6% in group A and 95.3% in group B (p>0.05). The cannulation time was significantly longer in the presence of PAD (5.1 min, vs. 4.09 min, p<0.05). There was no significant difference in the rate of overall adverse events and post ERCP pancreatic PEP. Conclusion: The presence of PAD did not affect the duration or success of the ERCP procedure. Furthermore, it was associated with longer cannulation time and increase in the cannulation difficulty, especially with PAD type 1.

As a combination of both concepts of innovation and environmental development, green innovation is of great significance to the sustainable development of the country and industry. Previous literatures have found the separate roles of green entrepreneurial orientation and inter-organizational learning in understanding green innovation issues. However, few studies have done a comprehensive analysis of integrating three streams of research: green entrepreneurial orientation, green innovation and supply chain learning capability. Based on the resource-based view and dynamic capability theory, we examine the direct of green entrepreneurial orientation on green innovation as well as indirect effect through the mediation of supply chain learning capability. Meanwhile, an empirical data set of 228 manufacturing companies in China (Shaanxi, Guangdong, Hebei, Jiangsu, and Shandong) was used to test our hypotheses. Findings from our empirical study suggest that supply chain learning capability partially mediates the positive relationships between green entrepreneurial orientation and its two consequences—green incremental innovation and green radical innovation. In addition, this research implies that when enterprise has a strong green entrepreneurial orientation, the enterprise should make an effort to enhance the level of supply chain learning capability so as to fully develop their green innovation.

Spatiotemporal variations of sediments transported along rivers play a crucial role in a wide spectrum of uses, such as navigation, recreation, habitats or hydropower production. The advancement in technology has made it possible to use various indirect techniques to study and evaluate the transport of suspended sediment in fluvial environments. To investigate large-scale phenomena, remote sensing is becoming a largely utilized approach, as it allows to combine spatially-distributed and local information. Dam-induced sediment reduction occurs in large and small rivers worldwide, having profound implications on the fluvial systems. However, the systematic change of suspended sediment concentration (SSC) and its dynamic processes are not well known, and generally investigated only at the very local scale using field information. In this work, SSC maps were created by combining satellite images with local monitoring SSC data, using the Zhijiang -Chenglingji reach of the Changjiang River (China) as a case study, and analyzing how SSC dynamics changed over the period 2017-2022 in correspondence of extreme events. Multiple relationships between measured SSC and bands reflectance were tested, showing the potential of the best-performing one (R2=0.43) in mapping SSC spatiotemporal variations over an extent of dozens of kilometres, eventually providing new insights into the SSC dynamics at hotspots of the river systems, such as confluence zones, barriers, and reservoirs.

Leak of carbon dioxide (CO2) from conventional underground carbon storage reservoirs is an increasing concern. It is highly desirable to inject CO2 into low-temperature reservoirs so that CO2 can be locked inside the reservoir in solid state as CO2-hydrates. Marine gas hydrate reservoirs and surrounding water aquifers are attractive candidates for this purpose. However, the nature of low-permeability of these marine sediments hinders injection of CO2 in commercial scale due to the low-injectivity of wells with conventional completions. This study investigates injection of CO2 into the low-permeability marine reservoirs using a new type of well namely radial-lateral wells (RLW). An analytical model was developed for predicting CO2 injectivity of the RLW to assess well injectivity improvement. A case study and sensitivity analysis were performed with field data from the South China Sea. Result of analysis reveals that the injectivity of the RLW is nearly proportional to reservoir permeability, lateral wellbore length, and number of laterals. CO2 injection rate is predicted to be 19 tons/day to 250 tons/day, which is 3 to 15 times higher than the injectivity of frac-packed wells. It is feasible to inject CO2 into the low-permeability-low-temperature marine reservoirs at commercial flow rates. This work provides an analytical tool to predict CO2-injectivity of RLW in low-temperature marine reservoirs for leak-free CO2 storage.

Retention mechanisms in HILIC have been investigated and reported in literature. However, the current understanding of the retention mechanisms is qualitative and lacks quantitative details. Previously, mechanism elucidation was based on indirect evidence, and unambiguous assignment of retention mechanisms has not been reported based on direct data. This study aims to quantitatively determine the contributions of two major retention mechanisms in HILIC, hydrophilic partitioning and surface adsorption to the overall retention of neutral compounds. Using the methodologies we developed previously, the phase ratio for adsorbed water layer and distribution coefficients were measured and used to calculate the retention factors attributed to hydrophilic partitioning. The methodology allows the determination of the contribution of surface adsorption simultaneously. The evaluation of five test compounds demonstrates that the retention may be controlled by hydrophilic partitioning, surface adsorption or both depending on compound characteristics. Quantitative assessment of retention mechanisms also makes it possible to better understand the effect of acetonitrile on retention in HILIC.

Information-Centric Networking (ICN) is a new paradigm of network architectures that focuses on content, rather than hosts, as first-class citizens of the network. As part of these architectures, in-network storage devices are essential to provide end users with close copies of popular content, to reduce latency and improve overall experience for the user, but also to reduce network congestion and load on the content producers. To be effective, in-network storage devices, such as content storage routers should maintain copies of the most popular content objects. Adversaries that wish to reduce this effectiveness can launch cache pollution attacks to eliminate the benefit of the in-network storage device caches. Therefore, it is crucial to protect these devices and ensure the highest hit rate possible. This paper demonstrates per-face popularity approaches to reducing the effects of cache pollution and improving hit rates by normalizing assessed popularity across all faces of content storage routers. The mechanisms that were developed prevent the consumers, whether legitimate or malicious, on any single face or small number of faces from overwhelmingly influencing the content objects that remain in the cache. The results demonstrate that per-face approaches generally have much better hit rates than currently used cache replacement techniques.

Optical and mechanical properties of multilayer coatings depend on the selected layer materials and the deposition technology; therefore, knowledge of the performances of thin films is essential. In the present work, titanium dioxide (TiO2) and silicon dioxide (SiO2) thin films have been prepared by plasma ion-assisted deposition (PIAD). The optical, structural, and mechanical properties of thin films have been investigated using spectrometer/ellipsometer, X-ray diffraction (XRD), atomic force microscopy (AFM), and laser interferometer. The results show that TiO2 film fabricated by PIAD induces a high refractive index, wide optical band gap, amorphous structure, smooth surface, and tensile stress. In the case of SiO2 film, high bias voltage leads to dense structure and compressive stress. As an application, a three-wavelength high reflectance at 632.8, 808, and 1550nm is optimized and deposited. The dependence of total stress in the multilayer on the substrate temperature is studied as well. In conclusion, it is demonstrated that PIAD is an effective method for the preparation of ultralow stress TiO2/SiO2 multilayer films. The achieved stress is as low as 1.4Mpa. The result could provide guidance to the stress optimization of most optical components without prefiguring, backside coating, and post-deposition treatments.