Aiming to improve the flame retardancy performance of natural rubber (NR), we developed a novel flame retardant synergistic agent through grafting of MCM-41 to graphene oxide (GO)，named as GO-NH-MCM-41，as an assistant of intumescent flame retardants (IFR). The structure of GO-NH-MCM-41 was characterized by FTIR, TEM and SEM tests, which confirmed that a fine grafting had been applied between GO and MCM-41. The flame retardancy of NR/IFR/GO-NH-MCM-41 composites was evaluated by limited oxygen index (LOI), UL-94 and cone calorimeter test. The LOI value of NR/IFR/GO-NH-MCM-41 reached to 26.3%; the UL-94 ratings improved to V-0 rating. Moreover, the addition of GO-NH-MCM-41 obviously decreased the peak heat release rate (PHRR) and the total heat release (THR) of the natural rubber composites. And the addition of GO-NH-MCM-41 increased the thickness of char residue. The images of SEM indicated the char residue were more compact and continuous. The degradation of GO-NH-MCM-41 based NR composites completed with a mass loss of 35.57% at 600 ℃. The tensile strength and the elongation at break of NR/IFR/GO-NH-MCM-41 composites were 13.9 MPa and 496.7%, respectively. The results of rubber process analyzer (RPA) reached the maximum value, probably due to a better network of the fillers in the matrix.

The effects of anisotropic properties (wettability and roughness) on microgroove surfaces in pool boiling heat transfer using Novec-7100 as a working fluid were experimentally investigated. The idea of introducing the concept of anisotropic wettability in boiling experiments draws inspiration from biphilic surfaces. The investigation is also motivated by two-phase immersion cooling, which involves phase-change heat transfer by using dielectric liquid as a working fluid. Very few studies have focused on the effects of surfaces with anisotropic properties on boiling performance. Thus, this study aims to examine the pool boiling heat transfer performance on surfaces with microgroove-induced anisotropic properties under the saturation condition. A femtosecond laser–texturing method was employed to create microgroove surfaces with different groove spacing. The results indicated that anisotropic properties affected the heat transfer coefficient and critical heat flux. Relative to the plain surface, microgroove surfaces enhanced the heat transfer performance due to the increased number of bubble nucleation sites and higher bubble detachment frequency. An analysis of bubble dynamics under different surface conditions was conducted with the assistance of high-speed images. The microgroove surface with groove spacing of 100 μm maximally increased the BHTC by 37% compared to the plain surface. Finally, the CHF results derived from experiments were compared with related empirical correlations. Good agreement was achieved between the results and the prediction correlation.

This study investigates the spatial and temporal dynamics of Paomo restaurants in Xi'an's central urban area from 2012 to 2023, leveraging Point of Interest (POI) data through a series of sophisticated analytical techniques. Methods including nearest neighbor distance, kernel density estimation, and band set statistical analysis were employed to thoroughly examine the evolutionary patterns and key drivers influencing the spatial distribution of these eateries. Our results highlight a notable trend of expansion from the central city to the periphery, characterized by significant spatial agglomeration. Initially concentrated in the city center, the distribution of Paomo restaurants has progressively shifted towards multiple distinct cores, reflecting the dual influence of urban policy initiatives and the dynamics of market competition. Furthermore, the research identifies several pivotal factors shaping this spatial distribution, particularly transportation access, residential quality of life, and the availability of commercial services. These findings demonstrate the profound effects of urban spatial reconfiguration and socioeconomic development on the specialized catering industry. The insights gleaned from this analysis offer valuable guidance for urban planners and policymakers, providing strategic recommendations for the spatial planning of specialty catering services to optimize urban layouts and foster sustainable economic progress.

Food security is the cornerstone of national security, and exploring the resilience of the grain industry chain is particularly important under the current complex and changing external environment. The study is to evaluate the grain industry chain resilience and identify its influencing factors. Based on the panel data of 30 provinces (cities) in China from 2011 to 2022, this paper adopted Partial Least Squares structural equation modeling method to carry out comprehensive evaluation, applied Dagum Gini coefficient to analyze spatial differences, and used geo-detectors to identify the influencing factors. The results showed that (1) from an overall perspective, the resilience of China's grain industry chain showed an overall upward trend, and each region had been greatly improved; (2) from the perspective of spatial differences, the overall spatial variability of China's grain industry chain is relatively small, and the gap mainly originates from inter-regional differences; (3) from the perspective of influencing factors, the level of grain foreign trade, regional market size and agricultural innovation level were important factors. In order to enhance the resilience of China's grain industry chain, based on the heterogeneous characteristics, the coordinated development of each region should be integrated, and the endogenous power should be given full play to enhance the resilience of the industry chain.

A plenty of theories on the origin of genetic codes have been proposed so far, yet all ignored the energetic driving force, its relation to the biochemical system, and most importantly, the missing “matchmaker” between proteins and nucleic acids. Here, a new hypothesis is proposed, according to which ATP is at the origin of the primordial genetic code by driving the coevolution of the genetic code with the pristine biochemical system. This hypothesis aims to show how the genetic code was produced e.g. by photochemical reactions in a protocell that derived from a lipid vesicle enclosing various life’s building blocks (e.g. nucleotides and peptides). At extant cell, ATP is the only energetic product of photosynthesis, and is at the energetic heart of the biochemical systems. ATP could energetically form and elongate chains of both polynucleotides and polypeptides, thus acting a “matchmaker” between these two bio-polymers and eventually mediating precellular biochemical innovation from energy transformation to informatization. ATP was not the only one that could drive the formation of polynucleotides and polypeptides, but favored by precellular selection. The protocell innovated a photosynthesis system to produce ATP efficiently and regularly with the aids of proteins and RNA/DNA. The completion of permanently recording the genetic information by DNA marked the dawn of cellular life operated by Darwinian evolution. The ATP hypothesis assumes or supports the photochemical origin of life, shedding light on the origins of both photosynthetic and biochemical systems, which remains largely unknown thus far. Based on ATP hypothesis, virus (like the new coronavirus) could not be the earliest life on Earth, as it has neither biochemical systems nor lipid bilayer membrane that provided relatively isolated environment for the development of protobiochemical reactions, although it owns the genetic code of a cellular life. Virus could not be a bridge between life and non-life, but is an anti-life substance, as it depletes cellular material for its own replication, and then spreads by destroying the host cells. It can be imagined that if cellular life are completely wiped out by the virus, the complete destruction of life on Earth would be inevitable.

Amid escalating urbanization, devising rational commercial space layouts is a critical challenge. Leveraging machine learning, this study uses a Back-propagation (BP) neural network to optimize commercial spaces in Weinan City's central urban area. The results indicate an increased number of commercial facilities with a trend of multi-centered agglomeration and outward expansion. Based on these findings, we propose a strategic framework for rational commercial space development emphasizing aggregation centers, development axes, and spatial guidelines. This strategy provides valuable insights for urban planners in small and medium-sized cities in the Yellow River Basin and metropolitan areas, ultimately showcasing the power of machine learning in enhancing urban planning.

This paper proposes two max-pooling engines, named the RTB-MAXP engine and the CMB-MAXP engine, with a scalable window size parameter for FPGA-based convolutional neural network (CNN) implementation. The max-pooling operation for the CNN can be decomposed into two stages, i.e., a horizontal axis max-pooling operation and a vertical axis max-pooling operation. These two one-dimensional max-pooling operations are performed by tracking the rank of the values within the window in the RTB-MAXP engine and cascading the maximum operations of the values in CMB-MAXP engine. Both the RBM-MAXP engine and the CMB-MAXP engine were implemented using VHSIC Hardware Description Language (VHDL) and verified by simulations. They have been employed for and tested in our CNN accelerator targeting at the CNN model YOLOv4-CSP-S-Leaky for object detection.

The ketogenic diet and walking exercise training activity are two key public health lifestyle factors. The potential of combined lifestyle factors interventions focused on getting to compliance in forced exercise. A balanced ketogenic diet and regular exercise activity is a key modifiable factor to the prevention and management of chronic diseases. Influence health across the lifespan and reduction of the risk of premature death through several biological mechanisms. Community older group’s lifestyle factors interventions contribute identity in their natural living environment. While the older health benefits of walking exercise training strategies are commonly to study, combined ketogenic diet and walking exercise interventions have induced greater benefits in community older groups.

: To improve the efficiency of rhizobial inoculation operations and address the current situation of rhizobial inoculation being labor-intensive, a spraying and control system for variable rate application (VRA) of liquid rhizobia was developed. The system can accurately regulate the spraying rate of liquid rhizobia according to the desired rate of rhizobia by incremental Proportional Integral Derivative (PID) closed-loop control algorithm, making it particularly suitable for precise spraying with small amounts. In the laboratory experiment of precise flow control, variation coefficient of spraying nozzle from 0.10 MP to 0.20 MP pressure were no more than 1.2%. A clear linear relationship was observed between the spraying rate and pressure. The maximum response time was 1.93 seconds, while the average response time was 1.62 seconds when controlling the spraying system for small amounts. Field trial was conducted in Heilongjiang Agricultural Xianghe Farm of China. Average seeds number and 100-seed weight of soybean plant with rhizobia inoculation treatment were better than control group, and average yield of spraying liquid rhizobia agent with full base fertilizer increased by 232.5 kg/hm2, representing a significant 7.4% improvement over the control group. The results of these trails clearly showed the positive effect of the spraying and control system for liquid rhizobial inoculation, which has superior to existing inoculation manners, and provides an important technical support for the widespread adoption of rhizobia technology.

This article obtains data through questionnaire survey, and then uses the Multiple Indicators Multiple Causes (MIMIC) Model to establish the Taoyuan City’s quality of life quantifying framework in a city-level community context. Statistical test results show that the reliability of overall model is high and is suitable for policy analysis. There are thirteen variables in the structural model that significantly affect the quality of life as well as eleven indicators in the measurement model that can significantly measure the quality of life. Then, half of the observations are substituted back to calculate the quality of life. Via ArcGis operation, it finds that the quality of life of Longtan District is the best as well as Dayuan District is the worst one. LISA cluster of quality of life illustrates hot spots areas are distributed in Longtan, Daxi, and Pingzhen Districts.

.Purpose: This paper presents a comparative analysis of state-of-the-art DIR algorithms in the context of head and neck squamous cell carcinoma (HNSCC) radiation therapy. Materials and Methods: We used a dataset of head and neck cancer patients within the Cancer Image Archive, which includes 31 patients with 3D CT image data from pre-treatment, mid-treatment, and post-treatment stages of radiotherapy. We applied DIR algorithms to two datasets, one for pre-treatment to mid-treatment registration and another for mid-treatment to post-treatment registration, by aligning one CT image to another CT image. To quantitatively analyze the patient data, we focused on the spinal cord, optic nerve, brain stem, cochlea, and PTV as the OAR datasets. To verify the DIR algorithm, we used two non-learning-based methods, SyN and NiftyReg, as well as three deep learning-based methods, Voxelmorph, Cyclemorph, and Transmorph. We trained a deep learning model by adjusting the ratio of the training dataset, validation dataset, and test dataset to 7:1:2. Results: The average DSCs of SyN and NiftyReg, the non-learning-based methods, were 0.74±0.06 and 0.70±0.12, respectively. The deep learning-based methods, Voxelmorph, Cyclemorph, and Transmorph, had average DSCs of 0.72±0.08, 0.68±0.11, and 0.69±0.13, respectively. The deep learning DIR algorithm produced transformed outputs of OAR/PTV in a shorter time than other models, including commercial and conventional mathematical algorithms (At Inference(sec/images), Voxelmorph: 0.36, Cyclemorph: 0.3, Transmorph: 5.1, SyN: 140, NiftyReg: 40.2). Conclusions: In conclusion, our study provides a comprehensive comparison of commercial DIR algorithms with traditional and deep learning-based DIR methods. Our results demonstrate that commercial DIR algorithms outperform traditional DIR methods in terms of accuracy and efficiency. However, we also show that deep learning-based DIR methods have the potential to achieve similar performance to commercial algorithms with proper training and optimization. Our findings suggest that both commercial and deep learning-based DIR methods have their respective advantages and limitations, and the choice of method should depend on the specific requirements of the clinical application. Overall, our study contributes to ongoing efforts to improve the accuracy and efficiency of DIR methods for better patient outcomes.

To understand lung damage caused by COVID-19, we deduced two-phase lung damage mechanisms. After the lungs are infected with SARS-CoV-2 virus, the affected lung tissue swells and surface properties of pulmonary capillaries change, resulting in an increased flow resistance of affected capillaries. If a sufficient number of capillaries are affected by the infection, the swelling and increased cell wall adhesion collectively raise pulmonary vascular resistance. The increased vascular resistance further increases the dwell times of WBCs in affected capillaries and nearly capillaries. When pulmonary pressure is sufficiently higher, WBCs are forced to squeeze into interstitial spaces or alveolar spaces when local pressures are higher than what the capillaries can withstand. When more and more WBCs are dynamically retained, the flow resistance of more capillaries rises, pulmonary vascular resistance rises, and pulmonary pressure rises. The rise in the pulmonary pressure in turn results in elevated capillary pressures. When capillary pressures around the alveoli are sufficiently high, they cause interstitial pressures to change from normally negative values to positive values. The positive pressures cause fluid leakage to the alveolar space and thus degrade lung function. Tissue swelling, and occupation of WBCs in interstitial spaces and alveolar spaces further reduce compressible volume, and thus cause further rise in the pulmonary vascular resistance and pulmonary pressure. When the pulmonary pressure has reached a critical point as in the second phase, the blood breaks capillary walls and squeezes through interstitial spaces to reach alveolar spaces, resulting in irreversible lung damages. The available free volume in the thorax cage, organ usable capacities, temperature and humid are expected to have great impacts on degree of lung damages. The free volume in the thorax cage, lung usable surplus capacity, and other organ usable capacities determine the arrival time of last-phase irreversible damage. The mechanisms imply that the top priority for protecting lungs is maintaining pulmonary micro-circulation and preserving organ functions in the entire disease course while controlling viral reproduction should be stressed in the earliest time possible. The mechanisms also explain leukecytes are recruited and migrated into inflamed tissues by increasing their dwell times caused by increased local flow resistance.

3,4-Dihydroquinolin-2(1H)-ones represent a class of valuable bioactive compounds with six-membered nitrogen-containing heterocyclic structures. The development of simple, mild and efficient synthetic methods has been widely concerned by synthetic chemists. In this review, we have summarized a series of different synthetic strategies for the synthesis of dihydroquinoline-2(1H)-ones via catalytic annulation of α,β-unsaturated N-arylamides in the past decade, including covering electrophilic cyclization, radical initiated cyclization and photochemical cyclization reactions. Besides, the substrate scope and mechanistic details are also discussed. This paper will provide a useful reference for the development of diverse synthesis methodologies of 3,4-dihydroquinolin-2(1H)-ones.

This study aimed to enhance the compatibility of glass ionomer cement (GIC) with tooth tissue by chemically modifying its primary component, calciumfluoroaluminosilicate (CFAS), through the incorporation of nanorod hydroxyapatite (nHA). The process involved binding L-glutamic acid to nHA, followed by activation and binding of albumin to create nHA immobilized with albumin. This modified nHA was then used to surface-modify CFAS particles, producing nHA-CFAS powder. The modified powder was mixed with poly(acrylic acid) and UV-cured to form GIC containing nHA-CFAS (GIC-nHA). Fourier transform infrared spectroscopy and scanning electron microscopy (SEM) confirmed the successful modification. Cytocompatibility tests with osteoblasts showed that GIC-nHA had superior cell viability and bone formation capabilities compared to the control GIC. The improved histocompatibility is attributed to nHA enhancing the biological activity of osteoblasts, indicating that the surface modification method significantly improves the functional integration of GIC with tooth tissue.

After reviewing cancer theories, cancer treatment development histories, randomized clinical trial's performance, cancer treatment strategy, trial follow-up times, and conducting numerous simulations using existing data, the authors found: (1) medical treatments come with three to four lethal factors: treatment side-effects, emotional distress and chronic dress, lack of exercises or physical inactivity, and excessive nutrition in some cases; (2) clinical trial exaggerates the benefits of fast-acting treatments and underestimates the slow-delivering adverse side effects as a result of statistical averaging, interfering effects of personal lifestyle factors, and insufficient follow-up times; (3) the benefits of medical treatments are limited by chain comparison, where surgery sets up a negative standard relative to the best way for resolving cancer; (4) the strategy of destroying the tumor is unworkable; (5) medical treatments can turn natural cancer growth curve into approximately doubly exponential curve; (6) multiple factor non-medical measures are much more powerful than medical treatments in controlling cancer growth and metastasis rates; and (7) cancer early diagnosis and over treatments are bad strategies that have great adverse impacts on cancer patients. Based on huge increases in cancer growth rate constants, substantial of loss of organ functional capacity, and severe systemic aging-like cellular damages, the authors concluded that medical treatments promote cancer growth and metastasis rates and shorten patient lives in most cases, and the claimed benefits are caused by triple biases of clinical trials. The authors believe that the better strategy for ending the global cancer epidemic is abandoning clinical trails as the research model, changing caner treatment strategy from killing cancer cells to slowing down cancer growth rates by using multiple factors optimization approach in personalized medicine.

The emergence of diverse infections worldwide, which is a serious global threat to human existence, necessitate the urgent development of novel therapeutic candidates that can combat these diseases with efficacy. Isatin, a secondary metabolite from tryptophan is considered a privileged scaffold and favorable pharmacophore with a unique structural moiety and varied chemical and biological properties resulting in its widespread applications by medicinal chemists. Molecular hybridization is one of the most common and important techniques use in the synthesis of their bioactive hybrids in drug discovery. This review containing published articles from 2005 to 2022 focuses on isatin hybrids which have been synthesized and reported in the literature alongside a discussion on their biological properties. The purpose of this review is to set up the direction for the design and development of isatin-hybrids with tailored biological properties as effective therapeutic candidates inspired by nature.

Instrumental activities of daily living (IADL) training is critical in clinical practice of occupational therapy (OT) for stroke patients. In the conventional approaches, the therapists simulate various occupational tasks in their healthcare settings or reach their nearby real circumstances for the training. As an alternative technology, immersive virtual reality (IVR) has been used widely in stroke rehabilitation for years; however, limited research has compared occupational performances between virtual and real environments. Our team has established a novel IVR shopping training system for stroke rehabilitation. We recruited 10 stroke patients from our department to test the system. All patients attempted to implement shopping tasks in the virtual and real environments respectively. The Wilcoxon test showed no significant differences between virtual and real environments in memory capacity and time-consuming for implementing tasks, and memory capacities in virtual and real environments presented excellent correlations with the IADL assessment. This study suggests that IVR shopping tasks can be used as an alternative approach in rehabilitation when there is limited resource for implementing shopping training in a real environment, while the psychometric property, clinical effect and the effect transferred to the real environment induced by virtual training require further study.

We conducted many model simulations to understand the causes of the damages of coronavirus (COVID-19) to lung tissue and constructed a diagram showing apparent viral reproduction, immune response and damage accumulation curves. We found that lung damages include virus-caused damage, tissue damage caused by immune responses and tissue damage caused by accumulated wastes. The virus-caused damage is proportional to the phase lag between the viral reproduction curve and the delayed adaptive immune response curve, while waste-induced damage is attributed to imbalance in removing viral, cellular and metabolic by-products. We found that treatment strategies should slow down viral reproduction and speed up immune response, and improve blood micro-circulation in the lungs. Consistent with the strategies, measures are taken to void direct lung infection, strengthen innate responses, promote immune responses, dilute viral concentration in lung tissue, maintain waste removal balance, protect heart and kidneys, control other infections, avoid allergic reactions and other inflammation, etc. We show that medical, dietary, emotional, lifestyle, environmental, mechanical factors, etc. may be simultaneously used to mitigate lung damages and prove that multiple factor health optimization method is magnitudes more powerful than a single factor treatment. Such a method does not depend on molecular specificity and can be used in parallel to antiviral drugs.

To understand great disparities in disease outcomes between CIVID-19 patients, we explore infection and host responses in kinetics. From existing data, we deduced a model that the lungs are damaged by rapidly rising flow resistance as a result of retaining white blood cells in lung tissues. The retention of white blood cells is initially triggered by viral infection but aggravated by injuries caused by low temperature. Lungs are initially damaged by fluid leakage, rapidly followed by extruding blood into alveolar spaces. The step of blood extruding is predicted to take place in a very short time. Our simulations show that as little as 0.1% retention of white blood cells in the lungs can lead to their failure in 5 to 10 days. The small degrees of imbalance implies that this imbalance could be corrected by a large number of factors that are known to reduce flow resistance. The model implies that the top priority is maintaining blood micro-circulation and preserving organ functions in the entire disease course, especially after the virus has spread the whole lungs. From exploring a large number of hypothetical infection modes, we propose preventive, mitigating and treatment strategies for ultimately ending the pandemic. The first strategy is avoiding exposures that could result in widespread damages to lungs and taking post exposure mitigating measures that would reduce disease severity. The second strategy is reducing death rate and disability rate from the current levels to one tenth for infected patients by using multiple factors health optimization method. The double reduction strategies are expected to generate a series of chain reactions that favor mitigating or ending the pandemic. Some reactions include a big reduction of the amount of viral discharges from infected patients into the air, the avoidance of panic, chronic stress and emotional distress, and cross-infections which are expected in quarantines. The double reductions would have a final effect of ending the pandemic.

Modern medicine adopted four presumptions when it evolved from ancient experienced-based mind-body medicine. To understand its failure in finding cures for chronic diseases, we examined four presumptions, and found that statistical population of health properties does not exist for most research purposes, mathematical models are misused to model intensive properties, synthetic drugs are inherently more dangerous than nature-made medicines under their respective application conditions, and reductionist treatments are inferior and inherently dangerous. We found that clinical trials are valid only for research where treatment effect is much stronger than the total effects of all interfering or co-causal factors or errors introduced by misused mathematical models can be tolerated. In all other situations, clinical trials introduce excessive errors and fail to detect treatment effects, or produce biased, incorrect or wrong results. We further found that chronic diseases are manifestation of small departures in multiple process attributes in distinctive personal biological pathways networks, that modern medicine lacks required accuracy for accurately characterizing chronic diseases, and that reductionist treatments are good at controlling symptoms and safe for short term uses. For all stated reasons, as long as modern medicine continues relying on the flawed presumptions, it can never find predictable cures for chronic diseases. By implication, predictable cures to chronic diseases are adjustments to lifestyle, dietary, emotional, and environmental factors to slowly correct departures in process attributes responsible for chronic diseases.

The effect of H2S with high concentrations on catalytic dry reforming of methane (DRM) process has seldom been focused on previously. Herein, a thermodynamic analysis of the DRM reactions in the presence of H2S with the concentration varying in 0-20 vol% was conducted firstly. Several typical types of catalysts including MgO, NiO/MgO and LaNiO3 in different states were prepared for executing DRM at 800 C, 0.1 MPa in the feed of 20 vol% CO2 and 20 vol% CH4 balanced with N2. The catalytic performance of each catalyst for DRM process under conditions of absence and presence of H2S was compared. A promotion effect of increasing H2S concentration on both the conversions of CO2 and CH4 and the molar yields of CO and H2 was observed on all the catalysts especially the MgO and the pristine NiO/MgO. While a significant decline in catalytic activity of either the reduced NiO/MgO or the reduced LaNiO3 catalyst after adding H2S, moderate reactant conversions still sustained. The results of process analysis and catalyst structure characterization suggest that H2S participation can contribute to the increment in CO2 and CH4 conversion, and active S-adsorbed species may play the key role of catalysis in the reactions involving H2S.

In the war against the COVID-19 pandemic, the world is experiencing severe resource constraints. Although transmission routes are well understood, we suspect that they cause different disease consequences. We evaluate them in different forms to understand how they affect infection rates and disease severity. In determining how they affect disease outcome, we evaluated target tissue vulnerability, functional role, defense mechanisms, viral concentration, infection vicinity to target vital tissue, and host factors. We found that direct lung infection is the most lethal transmission route followed by bronchi infection. Transmissions by physical contacts, foods, and blood by low viral concentration (as expected in normal human activities) pose lower or much lower risks unless the infection is followed by subsequent lung exposures. After adding transmission route, treatment timings, and improper treatments into the list of known risk factors, we found that death rate and disability rate for young or healthy persons are nearly zero. We show that population based medical model improperly shifts nominal death rate from few vulnerable people to the population resulting in unnecessary population panic, and such panic is responsible for shutting down human activities and the world economy. Finally, we examined limitations in population-based mitigating measures and proposed for governmental and private adoption community guidelines, which are mainly to enable vulnerable people avoid exposures, prevent non-vulnerable people from serving as viral transmitters, get rid of high-risk exposure modes in working environment, improve safety for people in buses, ships and planes, and reduce death and disability rates for infected people.

Chronic diseases are still known as incurable diseases, and we suspect that the medical research model is unfit for characterizing chronic diseases. In this study, we examined accuracy and reliability required for characterizing chronic diseases, reviewed implied presumptions in clinical trials and assumptions used in statistical analysis, examined sources of variances normally encountered in clinical trials, and conducted numeric simulations by using hypothetical data for several theoretical and hypothetical models. We found that the sources of variances attributable to personal differences in clinical trials can distort hypothesis test outcomes, that clinical trials introduce too many errors and too much inaccuracies that tend to hide weak and slow effects of treatments, and that the means of treatments used in statistical analysis have little or no relevance to specific patients. We further found that a large number of uncontrolled co-causal or interfering factors normally seen in human subjects can greatly enlarge the means and the variances of the experimental errors, and the use of high rejection criteria (e.g., low p values) further raises the chances of failing to find treatment effects. As a whole, we concluded that the research model using clinical trials is wrong on multiple grounds, under any of our realistic theoretical and hypothetical models, and that misuse of statistical analysis is most probably responsible for failure to identify treatment effects for chronic diseases and to detect harmful effects of toxic substances in the environment. We proposed alternative experimental models involving the use of single-person or mini optimization trials for studying low-risk weak treatments.

As climate changes, our daily life has been much influenced by abnormal meteorological phenomena such as heavy rainfall, heat wave, heavy snowfall, and fine dust. Atmospheric air quality is worsening day by day and indoor air quality is also affected by interconnected daily activities throughout the inside and outside of buildings and houses. Nowadays, pollutants from various sources are emitted, transformed by sunlight, vapor, and ozone and transported into the city from country to country. Due to these reasons, there have been high demands to monitor the transportation of particulate matters and improve air quality. Monitoring of pollutants and identification of type and its concentration enables us to track and control its generation and consequently find out the solution. However, monitoring of pollutants, especially, particulate matter generation and its transportation is still not fully operated in atmospheric air due to its open nature and meteorological factors. Even though indoor air is relatively easy to monitor and control than outdoor in the aspect of specific volume and contaminant source, but it still needs to consider the meteorological parameters because indoor air is not fully separated from the outdoor air flow and contaminants transportation. In this study, optical approach using spectral sensor was attempted to reveal the feasibility of wavelength and chromaticity values of reflected light from specific particles. From the analysis of reflected light of various particulate matters according to different liquid additives, parameter studies were performed to investigate which experimental conditions can contribute to the enhanced selective sensing of particulate matters. Five different particulate matters such as household dust, soil, talc powder, gypsum powder and yellow pine tree pollen were utilized and observed to elucidate the relationship between property of particulate matter and detected light spectrum. Applicable approaches to assist current particle matter sensors and improve the selective sensing were suggested.

Ehretia laevis Roxb. (Boraginaceae) has been extensively used as a traditional remedy for the treatment of a diverse range of ailments related to the respiratory system, the gastrointestinal tract, the reproductive system, and against several infections. This review critically assesses and documents, for the first time, the fragmented information on E. laevis, including its botanical description, folklore uses, bioactive phytometabolites and pharmacological activities. The goal is to explore this plant therapeutically. Ethnomedicinal surveys reveal that E. laevis has been used by tribal communities in Asian countries for the treatment of various disorders. Quantitative and qualitative phytochemical investigations of E. laevis showed the presence of important phytoconstituents such as pentacyclic triterpenoids, phenolic acids, flavonoids, fatty acids, steroids, alkaloids, aliphatic alcohols, hydrocarbons, amino acids, carbohydrates, vitamins and minerals. Fresh plant parts, crude extracts, fractions and isolated compounds have been reported to exhibit broad spectrum of therapeutic activities viz., antioxidant, antiarthritic, antidiabetic, anti-inflammatory, antiulcer, antidiarrheal, antidysenteric, wound healing and anti-infective activities. E. laevis is shown to be an excellent potential source of drugs for the mitigation of jaundice, asthma, dysentery, ulcers, diarrhea, ringworm, eczema, diabetes, fissure, syphilis, cuts and wounds, inflammation, liver problems, venereal and infectious disorders. Although few investigations authenticated its traditional uses but employed uncharacterized crude extracts of the plant, the major concerns raised are reproducibility of therapeutic efficacy and safety of plant material. The outcomes of limited pharmacological screening and reported bioactive compounds of E. laevis suggest that there is an urgent need for in-depth pharmacological investigations of the plant.

Background: This study aimed to investigate the impact of the COVID-19 pandemic on breast reconstruction trends in the United States, focusing on implant-based and autologous techniques, as well as the timing of reconstruction (immediate vs. delayed). Methods: A retrospective analysis of data from the American Society of Plastic Surgeons' National Plastic Surgery Statistics from 2015 to 2022 was conducted. Annual trends in breast reconstruction procedures were analyzed, comparing the pre-pandemic (2015-2019) and pandemic (2020-2022) periods. Results: The total number of breast reconstructions increased from 106,338 in 2015 to 151,641 in 2022. The proportion of implant-based reconstructions decreased from 81.41% pre-pandemic to 76.51% during the pandemic (p < 0.001), with a notable rise in direct-to-implant procedures from 10.37% to 19.12% (p < 0.001). Autologous reconstructions increased from 18.59% to 23.49% (p < 0.001). Among autologous techniques, DIEP flaps remained the most popular. Immediate reconstruction rates increased from 72.61% pre-pandemic to 75.57% during the pandemic, while delayed recon-struction rates decreased from 27.39% to 24.43% (p < 0.001). Conclusions: The COVID-19 pandemic has significantly influenced breast reconstruction trends in the United States, with a shift towards autologous techniques, particularly DIEP flaps, and an in-crease in immediate reconstructions. These changes may reflect adaptations in surgical practice and decision-making processes in response to the unique challenges posed by the pandemic. Further research is needed to assess the long-term outcomes and patient satisfaction associated with these trends.

The purpose of this paper is to propose a novel transfer learning regularization method based on knowledge distillation. Recently, transfer learning methods have been used in various fields. However, the problems such as knowledge loss still occur during the process of transfer learning to a new target dataset. To solve these problems, there are various regularization methods based on knowledge distillation techniques. In this paper, we propose a transfer learning regularization method based on feature map alignment used in the field of knowledge distillation. The proposed method is composed of two attention based submodules: self-pixel attention (SPA) and global channel attention (GCA). The self-pixel attention submodule utilizes both the feature maps of the source and target models, so that it provides an opportunity to jointly consider the features of the target and the knowledge of the source. The global channel attention submodule determines the importance of channels through all layers, unlike the existing methods that calculate these only within a single layer. Accordingly, transfer learning regularization is performed by considering both the internal of each single layer and the depth of the entire layer. Consequently, the proposed method using both of these submodules showed overall improved classification accuracy than the existing methods in classification experiments on commonly used dataset.

We study the Gaudin models with gl(1|1) symmetry that are twisted by a diagonal matrix and defined on tensor products of polynomial evaluation gl(1|1)[t]-modules, extending all the results of to the twisted case. Namely, we give an explicit description of the algebra of Hamiltonians (Gaudin Hamiltonians) acting on tensor products of polynomial evaluation gl(1|1)[t]-modules and show that there exists a bijection between common eigenvectors (up to proportionality) of the algebra of Hamiltonians and monic divisors of an explicit polynomial written in terms of the highest weights and evaluation parameters. In particular, our result implies that each common eigenspace of the algebra of Hamiltonians has dimension one. We also give dimensions of the generalized eigenspaces.

In this work, the Ni/Ti/Nb multilayer composite was successfully manufactured by accumulative pack-roll bonding. The microstructure evolution and mechanical properties of the composite during the accumulative roll bonding (ARB) process were investigated by scanning electron microscopy(SEM), energy dispersive spectrometer(EDS), transmission electron microscopy (TEM), micro-hardness and tensile tests. The results showed that after 5 passes of the ARB process, the deformations of layers were relatively uniform, and no large number of interlayer fractures occurred. The microstructures of Ni and Ti were both equiaxed grains with a grain size of 200 nm and 150 nm, respectively, and finer equiaxed grains of the Ni layer were observed at the interface. The laminar structure of Nb layer was observed. The tensile strength and micro-hardness increased significantly as the number of ARB increased. After 5 passes of the ARB process, the tensile strength of the composite reached 792.3 MPa, and the micro-hardness of Ni, Ti, and Nb were increased to 270.2, 307.4, and 243.4 HV, respectively.

Nicotine exposure may affect NSCLC is associated with lung cancer in humans. Whether nicotine exhibits carcinogenesis promoted activities in tumor growth still unknown. Nicotine is known to have dichotomous effects on cancer biology, acting like a pro- or anti-carcinogenesis agent. There are different functions between adenocarcinoma and squamous NSCLC cancer cells. Excess generation of nicotine may inhibit mitochondrial metabolism, protein modification, and DNA cleavage. Materials and Methods: We used the H520 NSCLC line obtained from human lung epithelial cells to detected nicotine growth and toxicity using MTT assay and western blotting. The concentration of nicotine stimulated cell growth to correspond to low concentration, while high concentration was cytotoxic. Results: According to MTT assay results, at 1.0 μM nicotine has significantly enhanced the H520 cell viability (%). Nicotine induced lung cancer carcinogenesis through mechanisms of α7nAchR, EGFR, HDAC2/4/5, Cyclin D/Cyclin E, Bcl-2, p-Akt, and inflammatory proteins of NF-KappaB and COX2 increases at 1.0 μM. Apoptosis proteins were decreases at 1.0 μM nicotine by p21, p27, c-jun, and p38α using western blotting. Nicotine stimulates tumor growth is mediated through α7nicotinic-acetylcholine receptors (α7nAChR), possibly involving inflammation. On the other hand, at high nicotine concentrations (> 1.0 μM) with consistent cytotoxic effects and appeared to be due to direct cell kill. Nicotine can prevent apoptosis induced by NSCLC. Conclusion: Therefore, the effects on chemotherapeutics by NSCLC malignant cell lines, nicotine in concentrations as low as 1.0 μM decreased. These mechanisms are responsible for the genotoxic effects caused by nicotine. This leads to downstream effects on decreased apoptosis, increased cell proliferation and transformation. The malignant NSCLC cells respond to the treatment with nicotine in lung cancer, the nicotine-mediated induction of growth may provide one of its links to α7nAchR or EGFR.

The conceptualisation of happiness varies across different cultures. In Chinese culture, happiness is not only inclusive of oneself, but also hinges on the people is related to and society. Chinese social development have influenced psychological traditionality and modernity and individual's happiness. In Experienment1, 450 participants were recruited and surveyed to examine the levels of happiness amongst Chinese undergraduates with diverse cultural values. The results showed that individuals with both traditional and modern psychological orientations had high levels of happiness. Those with higher psychological traditionality showed more satisfaction with family relationships and social happiness, while those with higher psychological modernity demonstrated a higher level of relational happiness. In Experienment2, 280 participants were recruited, and a "happiness token distribution" and "happiness importance survey" were employed to draw a 'happiness circle' for Chinese undergraduates. The results revealed that those with a higher degree of psychological traditionality assigned a greater proportion of their happiness to ascribed relationships. In contrast, those with a higher degree of psychological modernity allocated a larger share of their happiness to interactive relationships and social relationships. Individuals with lower values of both traditionality and modernity perceived themselves as the most important component in their happiness circle.

With the outbreak of coronavirus disease 2019 (COVID-19), there is a need for efficient management of patients with mild or no symptoms, which account for the majority. The aim of this study is to introduce the structure and operation protocol of a living and treatment support centre (LTSC) operated by Seoul National University Hospital in South Korea. The existing accommodation facility was converted into a 'patient centre' where patients was isolated. A few Medical staff here performed medical tests and responded to emergencies. Another part of the LTSC was 'remote monitoring centre'. In this center, patients’ self-measured vital signs and symptoms were monitored twice a day, and the medical staff staying here provided video-consultation via a smartphone. During the 3 weeks from March 5 to March 26, 2020, 113 patients were admitted and treated. LTSC could be an efficient alternative to hospital admission in pandemic situation like COVID-19.

In the ground-based infrared optical remote sensing system, the target signal is very weak due to the dynamic strong light background and the movement of small and small targets. In order to improve the limit detection capability, the background suppression and target enhancement methods are required to be more suitable for this scene. To solve this problem, we first analyze the image features in the current scene, and propose a more perfect point target and noise model. Then, we propose a new WY distribution function based on the Fermi Dirac distribution function, and propose an anisotropic filtering method based on this function, and further suppress the back-ground through the difference results of two steps. Then, based on the distribution function, we further designed an energy concentration accumulation strategy in 9 scale directions, through which the SNR of the target is effectively improved and the suppression ability of the background is enhanced. Through quantitative and qualitative experimental analysis, compared with the same type of algorithms, the proposed method has better robustness against extremely weak targets and dynamic backgrounds.

Blood image intensity has been used to detect erythrocyte sedimentation rate (ESR). However, it does not give an information on biophysical properties of blood sample under continuous ESR. In this study, three physical properties, including, τ₀, ESR_τ, and AI_I, are suggested to quantify mechanical variations of blood under continuous ESR. To demonstrate the proposed method, blood sample is loaded into a driving syringe. The blood flow rate is set in a periodic on–off pattern. Blood sample is then supplied into a capillary chip, and microscopic blood images are captured at specific intervals. Blood shear stress is quantified from the interface of blood stream in the coflowing channel. Both τ₀ and ESR_τ are then obtained by analyzing the blood shear stress. Simultaneously, the AI_I is evaluated by analyzing the image intensity of blood flow. According to the experimental results, the τ₀ exhibits consistent trends with respect to hematocrit as well as diluent. The ESR_τ and AI_I showed a reciprocal relationship each other. Three suggested properties represented substantial differences for suspended blood samples (i.e., hardened red blood cells, different concentration of dextran solution and fibrinogen). In conclusion, the present method can detect variations of blood sample under continuous ESR effectively.

Parasitic diseases continue represent a threat on a global scale, particularly among the poorest countries in the world. This is particularly because of the absence of vaccines, and in some cases, resistance against available drugs, currently being used for their treatment. In this review emphasis is laid on natural products and scaffolds from African medicinal plants (AMPs) for lead drug discovery and possible further development of drugs for the treatment of parasitic diseases. In the discussion, emphasis has been laid on alkaloids, terpenoids, quinones, flavonoids and narrower compound classes of compounds with micromolar range activities against Schistosoma, Trypanosoma and Leishmania species. Suggestions for future drug development from African medicinal plants have also been provided.

With the rapid development of the economy and the transformation of social contradictions, the economic development model in China has also changed, and a high-quality economic development model has been proposed. This paper uses the entropy method to measure the level of innovation and high-quality economic development in nine prefecture-level cities in Fujian Province from 2011 to 2020, and finds that the overall level shows an increasing trend year by year, but there are obvious regional differences. By constructing a grey correlation degree model, it is found that the innovation subsystem and the high-quality economic development are strongly correlated, the development level of innovation and the subsystem of high-quality economic development are both strongly correlated, the grey correlation degree from high to low is green, coordinated, shared, and livelihood, indicating that innovation has a significant impact on high-quality economic development. Based on the research results, countermeasures and suggestions are proposed to promote the coordinated development of innovation and high-quality economy.

Recycling waste products is an environmental-friendly activity that can bring benefits to accompany, saving manufacturing costs and improving economic efficiency. For the beer industry, recycling bottles can reduce manufacturing costs and reduce the industry's carbon footprint. This paper presents a model for a multi-objective collection-distribution center location and allocation problem in a closed loop supply chain for the beer industry, in which the objective is to minimize total costs and transportation pollution. Uncertainties in the form of randomness and fuzziness are jointly handled in this paper to ensure a more practical problem solution, for which returned bottle sand unusable bottles are considered fuzzy random variables. A heuristic algorithm based on priority-based global-local-neighbor particle swarm optimization (pb-glnPSO) is applied to ensure reliable solutions for this NP-hard problem. A case study on a beer operation company is conducted to illustrate the application of the proposed model and demonstrate the priority-based global-local-neighbor particle swarm optimization.

Studies investigating the acute effect of postprandial exercise (PPE) on glucose responses exhibit significant heterogeneity in terms of participant demographic, exercise protocol, and exercise timing post-meal. As such, this study aimed to further analyze the existing literature on the impact of PPE on glycemic control in individuals with overweight, obesity, and type 2 diabetes (T2D). Literature search was conducted through databases including PubMed, CINAHL, and Google Scholar. Thirty-one original research studies that met the inclusion criteria were selected. The random-effect meta-analysis was performed to compare postprandial glucose area under the curve (AUC) and 24-h mean glucose levels between PPE and the time-matched no-exercise control (CON). Subgroup analysis was conducted to explore whether the glucose-lowering effect of PPE could be influenced by exercise duration, exercise timing post-meal, and disease status of participants. This study revealed significantly reduced glucose AUC (Hedges’ g = -0.317; SE = 0.057; p < 0.05) and 24-hour mean glucose levels (Hedges’ g = -0.328; SE = 0.062; p < 0.05) following PPE than CON. The reduction in glucose AUC was greater (p < 0.05) following PPE lasting >30 min than ≤30 min. The reduction in 24-hour mean glucose levels was also greater (p < 0.05) following PPE initiated ≥60 min than <60 min post-meal and in those with T2D than those without T2D. PPE offers a viable approach for glucose management and can be performed in various forms so long as exercise duration is sufficient. The glucose-lowering effect of PPE may be further enhanced by initiating it after the first hour post-meal. PPE represents a promising strategy, particularly for patients with T2D.

Acquired Immunodeficiency Syndrome (AIDS) which is chiefly originated by a retrovirus named Human Immunodeficiency Virus (HIV), has influenced about 70 million populations worldwide. Even though several advancements have been invented in the field of antiretroviral combination therapy, still HIV has become the dominant reason for death in South Africa, for example. The current antiretroviral therapies have achieved success in providing instant HIV suppression but with countless undesirable adverse effects. In the present day, the biodiversity of the plant kingdom is being explored by several researchers for the discovery of potent anti-HIV drugs with different mechanisms of action. The primary challenge is to afford a treatment that is free from any sort of risk of drug resistance and serious side effects. Hence, there is a strong demand to evaluate the drugs obtained from natural plants as well as the synthetic derivatives that have been derived from the natural compounds by various chemical reactions. Several plants such as Andrographis paniculata, Dioscorea bulbifera, Aegle marmelos, Wistaria floribunda, Lindera chunii, Xanthoceras sorbifolia and others have displayed significant anti-HIV activity showing more potent anti-HIV activity along with their structures, SARs & important key findings.

The construction of sustainable urban forests follows the principle that well-being in people is promoted when exposed to tree population. Facial expression is the direct representation of inner emotion that can be used to assess real-time perception in urban forests. The emergence and change of facial expressions for forest visitors are in an implicit process. The reserved character of oriental races strengthens the requirement for the accuracy to recognize expressions through instrument rating. In this study, a dataset was established with 2,886 randomly photographed faces from visitors in a constructed urban forest park and a promenade at summertime in Shenyang City at Northeast China. Six experts were invited to choose 160 photos in total with 20 images representing one of eight typical expressions as angry, contempt, disgusted, happy, neutral, sad, scared, and surprised emotions. The FireFACE ver. 3.0 software was used to test hit-ratio validation as the accuracy (ac.) to match machine-recognized photos with those identified by experts. According to Kruskal-Wallis test on the difference from averaged scores in 20 recently published papers, contempt (ac.=0.40%, P=0.0038) and scared (ac.=25.23%, P=0.0018) expressions cannot pass the validation test. Therefore, the FireFACE can be used as an instrument to analyze facial expression from oriental people in urban forests but contempt and scared expressions cannot be identified.

To predict how the COVID-19 pandemic progresses, we developed a systematic method for predicting disease outcomes. In the method, we evaluate how personal disease outcomes are mainly affected by viral concentration and exposure time and four defense mechanisms: human innate immunity/host response, acquired immune response, inflammation resolution and micro circulation, and the available space in the thorax cage. By considering how pandemic measures affect viral exposure and those mechanisms, we found many pandemic measures are misused or abused to deliver long-term adverse impacts. We noted that lifestyles have been changed as a result of movement restriction measures. By using the method, we found that altered lifestyles are predicted to raise infection rate, disability and death risks in the future. We show that a person can use personal, environmental, emotional factors to reduce infection rate and death risk. To prove the validity of this finding, we extensively examined medical research models, holistic and reductionist models, epidemiological models, disease risk factors, etc, and found that population methods are unfit for studying holistic health, statistical population does not exist in most clinical trials, mathematical models were misused for studying disease properties for a population, mathematical equations for modeling personal diseases are beyond human ability to solve, statistical models are misused, population-derived treatments are inherently dangerous to patients, vaccines have limited benefits due to unique lung structure and rapid RNA mutation, and immune system damage is caused by fast viral replication rate. We found that altering biological properties to improve the defense mechanisms could prevent a super majority of deaths and prevent the virus from reaching a point to damage the immune system. For vulnerable persons, such measure is a viable strategy for surviving from the pandemic. As a whole, holistic personalized medicine is more powerful than population-based reductionist treatment by one to several orders of magnitudes. We urge people do their parts to force the medical establishment to abandon population treatment models that are responsible for failure of medicine and dissemination of misleading and factually wrong information on the effectiveness of medical treatments.

We previously proposed a public intervention framework concept that would allow people to resume personal and economic activities. We showed that intervention measures are used in a quantitative scale to reduce transmission probabilities and disease severity. In this article, we systematically examine the origin, assumptions, performance and limitations of epidemiological models from different views used in past review. We found that nearly all model assumptions fail to hold or are remote from reality; R0 does not exit or has no utility in guiding treatment options; personalized intervention measures are vitally important to COVID-19 due to its transmission characteristic; and current epidemiological models are unable to accurately assess the true benefits of personalized intervention measures. We suggest that poor performance of the models are attributed to flawed assumption that health/disease properties can be treated as transferable properties. The flaw creates a fiction that disease properties such as infection probabilities and death risks can be transferred from any vulnerable persons to anyone in the population and thus severely limit societal ability to fight the pandemic. We finally show that the benefits of personalized mitigation measures could be determined directly by using variable Ri values for infected persons (or nodes) together assessment of death rate and disability rate; the attempt of avoiding the disease by defeating all potential transmission probabilities is unrealistic; but mitigating disease severity for specific persons is more feasible and reliable. A most reliable strategy for reviving economy is using personalized protective measures and improving person health before effective vaccine is available.

The COVID-19 pandemic has great adverse impacts on personal life, the U.S. economy, and the world economy. Freezing all human activities is not a sustainable measure. Thus we want to develop a public intervention framework that allows people to resume personal and economic activities. In this article, we examined transmission routes, disease severity, personal vulnerability, available treatments, and person-person interactions to establish a general public intervention framework. We divide people into risk groups, non-risk group and group that may serve as viral transmitters, explore interactions between individual persons within each group and between different groups, and propose interaction behavior modifications to mitigate viral exposures. For the non-risk groups, we identified preventive measures that can help them avoid the most serious exposures and infections that pose higher death risks. The invention measures for the vulnerable groups include prior-exposure measures, heightened protective measures, interaction behavior changes, post-exposure remedial measures, and multiple factors treatments to reduce death and disability risks. The multiple interventions and two-ways defensive behavior modifications are expected to result in reduced rate of detectable infections and lowered disease severity for the vulnerable groups. In this framework, most human activities and economic activities can continue as normal. With time passing, the population acquires population immunity against the COVID-19 virus. Implementation of this intervention framework requires considerable resources and governmental effects while the multiple factors treatment protocol requires the support of health care professionals.

We examined special roles of the Central Nervous System (CNS) in an attempt to resolve the puzzle that chronic diseases cannot be cured by medicine. By exploring a skill-learning model, we found that the CNS is able to remember certain information reflecting biochemical and cellular (B&C) processes in the body. From the skill using ability, we found that the CNS is able to control basic B&C processes that drive and power the skill. From the ability to adjust forces and force direction of a physical act, we found that the CNS is able to adjust B&C processes that drive the physical act. From this adjustment capability, we further inferred that the CNS must also store information on the baseline B&C processes. As a whole, we found that the CNS can maintain information on baseline B&C processes, up-regulate or down-regulate the processes, and make comparisons in performing its regulatory functions. We found that chronic diseases are the results of deviated baseline B&C processes. Per the proved hypothesis, the CNS maintains deviated baseline B&C processes, and thus protects the body states of fully developed diseases. We then used the three CNS roles to explain that cancer progresses with increasing malignancy, cancer quickly returns after a surgery, cancer cells repopulate after chemotherapy and radiotherapy, cancer develops drug resistance inevitably, immune cells rebound after suppression, generally poor benefits of cancer drugs such as beta-blockers, etc. We further showed that long-term exercises generally push most, if not all, baseline B&C processes in diametrical opposing directions against the diseased B&C processes, implying that exercises play unique roles in reversing chronic diseases. Finally, we proposed several strategical approaches to resetting the CNS’ state memory as the essential condition for curing chronic diseases.

The fluorine-less noble-gas containing anions OBONgO- and OCNNgO-have been studied by correlated electronic structure calculation and density functional theory. The obtained energetics indicates that for Ng = Kr and Xe, these anions should be kinetically stable at low temperature. The molecular structures and electron density distribution suggests that these anions are stabilized by ion-induced dipole interactions with charges concentrated on the electronegative OBO and OCN groups. The current study shows that in additional to the fluoride ion, polyatomic groups with strong electronic affinities can also form stable noble-gas containing anions of the type X-...NgO.

Drafting formations have been long recognized as highly effective for reducing drag and enhancing athletic performance, particularly in race walking events. The precise spacing and positioning of the race walkers are critical to optimizing the effectiveness of drafting. In this study, the drag reduction of 15 drafting formations is investigated using wind-tunnel experiments and CFD numerical simulations. The results show excellent consistency in drag reduction rate between the two methods, with differences being within 10%. This can be attributed to spacing replacing body shape differences as the primary factor influencing drag reduction. Optimal double, triple, and quadruple drafting formations produce the same results in both wind-tunnel experiments and CFD simulation, resulting in drag reductions of 67%, 66%, and 81% (wind-tunnel) and 65%, 72%, and 85% (CFD). The sources of drag differences in the two methods are discussed from various aspects. The flow field obtained through CFD analysis is used to examine the mechanism of drag reduction, revealing that drafting formations have a significant shielding effect on incoming air, which reduces the number and speed of airflow impacting the core race walker. This shielding effect is identified as the primary cause of drag reduction. Using an empirical model for mechanical power output, optimal double, triple, and quadruple drafting formations enhance sport economy (4.4-5.7%), speed (3.61-4.67%), and performance (173.8-223.3s) compared to race walking alone. The findings can serve as a reference for race walkers' positioning strategy and provide insights for considering drafting formations in various running events.

A multispectral superconducting nanowire single photon detector sensitive to different incident photon wavelength bands, is proposed. The SNSPD consists of a Distributed Bragg Reflector, a gold mirror, and two regions employing four NbN nanowires. Using the DBR both as a filter and a reflector, two distinct detection bands are created. The first detection band has a peak absorbance of > 0.75 at a wavelength of 1143 nm, while the second band has an absorbance of > 0.70 in the wavelength range 1440 to 2000 nm. The design of the device can be tuned to provide sensitivity in different wavelength bands. While SNSPDs do not typically provide photon wavelength sensitivity, the band-selection design proposed in this work opens up potential applications for future quantum communication technology.

Tulou dwellings in Southeast China have captivated global interest due to their distinctive appearance, sustainable construction materials and technologies, and their defensive and collective housing functions. Despite several recognized as World Cultural Heritage sites, the vast majority of tulou buildings are undergoing irreversible decline and destruction, necessitating a comprehensive and systematic study. Taking 83 Tulou buildings in Raoping County, Chaozhou City, Guangdong Province as the research object, this study reconstructs the historical scenes and systematically reveals the emergence, popularity, and consolidation process of tulou dwellings as integrated defensive and residential buildings for ordinary people by conducting a comprehensive analysis of historical documents and local chronicles. Based on an extensive field investigation, the study systematically analyzes the geospatial distribution and the spatial characteristics of Raoping tulou and its residential unit. The results demonstrate the adaptability and flexibility of tulou dwellings, showcasing their developmental process and revealing the inclusive nature of these traditional residences, as well as the initiative of those who reside within them. The research findings contribute to a more dynamic, comprehensive, and authentic understanding of tulou and Chinese traditional residences, providing valuable references for the preservation and sustainable development of tulou architectural heritage.

The proliferation of ransomware poses a significant threat to global cybersecurity. This study presents a comprehensive review of the methodologies employed in the detection and analysis of ransomware, emphasizing the dichotomy between static and dynamic analysis approaches. It introduces the historical context and the necessity for robust cybersecurity measures, followed by an outline of the methodological framework used to evaluate existing ransomware analysis techniques. The results detail the effectiveness and limitations of various analysis strategies, identifying key features and patterns that aid in the detection and classification of ransomware threats. The study concludes by summarizing the primary achievements, including the identification of gaps in current research and proposing future research directions aimed at enhancing ransomware detection and mitigation strategies. The synthesis provided in this survey offers a consolidated view of the state-of-the-art in ransomware threat analysis and serves as a resource for cybersecurity professionals and researchers.

Herpesviridae is a family of enveloped double-stranded DNA viruses that cause a wide range of diseases in hosts. Among the various components of herpesvirus particles, tegument proteins residing between the envelop and nucleocapsid play crucial roles in viral replication, immune evasion, and modulation of host cellular pathways. Understanding the three-dimensional structure of herpesvirus tegument proteins help to reveal the molecular mechanism underlying the crosstalk with other viral and cellular components, and thus is crucial for the investigation of their biological and pathological functions. In this review, we summarize the current knowledge of the structural features of herpesvirus tegument proteins, highlighting the structure-based functional implications, including the potential as targets for antiviral drug development.

The open communication is an exigent need for future power system where the time delay is unavoidable. In order to secure the stability of the grid, the frequency must remain within its limited range which is achieved through the load frequency control. The load frequency control signals are transmitted through communication networks which induces time delay that could destabilize the power systems. So, in order to guarantee the stability the delay margin should be computed. In this paper, we present a new method for calculating the delay margin in load frequency control systems. The transcendental time delay characteristics equation is transformed to frequency dependant equation. The spectral radius is used to find the frequencies at which the roots crosses the imaginary axis. The crossing frequencies are determined through the sweeping test and the binary iteration algorithm. A one-area load frequency control system is chosen as case study. The effectiveness of the proposed method has been proved through comparing with the most recent published methods. The method shows its merit with less conservativeness and less computations. The PI controller gains are preferable to be chosen large to reduce the damping, however, the delay margin decreases with increasing the PI controller gains.

Currently available data are consistent with increased severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) replication at temperatures encountered in the upper airways (25–33°C when breathing room temperature air, 25°C) compared to those in the lower airways (37°C). One factor that may contribute to more rapid viral growth in the upper airways is the exponential increase in SARS-CoV-2 stability that occurs with reductions in temperature, as measured in vitro. Because SARS-CoV-2 frequently initiates infection in the upper airways before spreading through the body, increased upper airway viral growth early in the disease course may result in more rapid progression of disease and potentially contribute to more severe outcomes. Similarly, higher SARS-CoV-2 viral titer in the upper airways likely supports more efficient transmission. Conversely, the possible significance of air temperature to upper airway viral growth suggests that prolonged delivery of heated air might represent a preventative measure and prophylactic treatment for coronavirus disease 2019.

Currently there are fewer depth models applied to pepper picking detection, while the existing generalized neural networks have problems such as large model parameters, long training time, and low model accuracy.In order to solve the above problems, this paper proposes a Yolo-chili target detection algorithm for chili pepper detection. First, the classical target detection algorithm yolov5 is used as a benchmark model, and an adaptive spatial feature pyramid structure combining the attention mechanism and the idea of multi-scale prediction is introduced to improve the model's detection effect on occluded peppers and small target peppers. Secondly, a three-channel attention mechanism module is introduced to improve the algorithm's long-distance recognition ability and reduce the interference of redundant testers. Finally, the quantized pruning method is used to reduce the model parameters and realize the lightweight processing of the model. Applying the method to the homemade chili pepper dataset, the AP value of chili pepper reaches 93.11%; the accuracy rate is 93.51% and the recall rate is 92.55%.The experimental results show that yolo-chili is able to achieve accurate and real-time pepper detection under complex orchards.

Wound healing is a process through which skin maintains itself. Once a wound occurs, the inflammatory and proliferative stages are instigated in reaction to injury. It is established that wound restorative comprises four stages including haemostasis, inflammation, proliferation, and remodeling. The amelioration of wound healing is very challenging as tumors can develop at the site of chronic injury. There are numerous plants, plant extracts and plant based natural products were widely used by tribal communities from ancient times for the treatment of cuts, burns, scars, burns and wounds. The therapeutic potential of these plants is recognized due to the presence of phytomolecules such as phenolic compounds, flavonoids, triterpenoids, saponins, tannins, alkaloids and glycosides. The plant used for the treatments of wound healing includes Achillea millefolium, Andrographis paniculata, Boswellia sacra, Calendula officinalis, Crocus sativus, Curcuma longa, Ehretia laevis, Ehretia microphylla, Glycyrrhiza glabra, Malva sylvestris, Rosmarinus officinalis and Salvia officinalis. This assemblage comprises the structures of phytomolecules isolated from the different extracts of these plants, mechanistic insights and important key findings responsible for wound healing. The mechanistic insights involved in wound healing are similar to cytotoxic, anti-inflammatory and antioxidant agents such as ROS generation, DNA fragmentation and western blotting. This review article is an effort to bridge the gaps in the prevailing literature and thus offers gigantic scope for researchers and academicians betrothed in validation of the customary claims and development of safer and efficient and worldwide recognized natural potential candidates as drugs for healing of wounds, burns and cuts.

(1) Background: Most hemodialysis patients may experience physiological and psychological stress. Exposure to nature has been previously reported to reduce the measures of psychological and physiological stress, and immune function. This study aimed to investigate psychological and physiological effects of integrated indirect forest therapy on chronic renal failure patients undergoing hemodialysis. (2) Methods: As a quasi-experiment, this study employed a nonequivalent control group, repeated measurements, and a non-synchronized design. A total of 54 participants were included: 26 and 28 in the experimental and control groups, respectively. During hemodialysis, five types of forest therapy stimuli (visual, auditory, olfactory, tactile, and motor) were applied 3 times per week for 4 weeks during 15-minute sessions. (3) Results: Positive but not negative emotion measures differed between the groups after the intervention. Fatigue and physiological stress levels were significantly reduced in the experimental group, whereas no significant difference was found between the groups on the measures of psychological stress. Activation of both the parasympathetic and sympathetic nervous systems was similar in both groups, as was the number of natural killer cells. (4) Conclusion: Integrated indirect forest therapy may help increase positive emotions and reduce fatigue and stress levels during hemodialysis in patients with chronic renal failure.

The last-mile logistics in cities have become an indispensable part of the urban logistics system. This study aims to explore the effective selection of last-mile logistics nodes to enhance the efficiency of logistics distribution, strengthen the corporate distribution image, and further reduce corporate operating costs and alleviate urban traffic congestion. This paper proposes a clustering-based approach to identify urban logistics nodes from the perspective of geographic information fusion. This method comprehensively considers several key indicators, including the coverage, balance, and urban traffic conditions of logistics distribution. Additionally, we employed a greedy algorithm to identify secondary nodes around primary nodes, thus constructing an effective nodal network. To verify the practicality of this model, we conducted an empirical simulation study using the logistics demand and traffic conditions in the Xianlin District of Nanjing. This research not only identified the locations of primary and secondary logistics nodes but also provided a new perspective for constructing the urban last-mile logistics system, enriching the academic research related to logistics node construction. The results of this study are of significant theoretical and practical importance for optimizing urban logistics networks, enhancing logistics efficiency, and promoting the improvement of urban traffic conditions.

This paper presents a critical review and comparison of the results of recently published studies in the fields of human-machine interface and the use of sonomyography (SMG) for the control of upper limb prothesis. For this review paper, a combination of the keywords "Human Machine Interface", "Sonomyography", "Ultrasound", "Upper Limb Prosthesis", "Artificial Intelligence" and "Non-Invasive Sensors" was used to search for articles on Google Scholar and PubMed. Sixty-one articles were found, of which 59 were used in this review. For a comparison of the different ultrasound modes, feature extraction methods, and machine learning algorithms, 16 articles were used. It was found that various modes of ultrasound devices for prosthetic control, various machine learning algorithms for classifying different hand gestures, as well as various feature extraction methods for increasing the accuracy of artificial intelligence used in their controlling systems are reviewed in this article. The results of the review article show that ultrasound sensing has the potential to be used as a viable human-machine interface in order to control bionic hands with multiple degrees of freedom. Moreover, different hand gestures can be classified by different machine learning algorithms trained with extracted features from collected data with an accuracy of around 95%.

Powdery mildew disease, caused by Sphaerotheca fusca, is a major disease affecting cucumbers cultivated in greenhouses. This study was conducted to find defense genes induced by DL-3-amino-butyric acid (BABA) and powdery mildew in cucumber. The 2000 and 5000 mg/L BABA treated cucumber exhibited disease severity of 25% and 5%, respectively, whereas the water treated cucumber leaves were severely infected, with a disease severity of 90%. BABA did not effect spore germination of the powdery mildew pathogen,. showing BABA is not antifungal agent against the pathogen. In quantitative real-time PCR analysis, BABA treated cucumber upregulated transcriptional level of the defense genes CsPAL, CsPR3,CsPR1, CsLOX1, CsLOX23, Cs LecRK6.1, CsWRKY20, and Cupi4 in cucumber to maximum levels at 48 h, whereas CsLecRK6.1 reached maximum expression after 24 h and futher salicylic acid (SA) levels were significantly increased in BABA-treated cucumber plants. In addition, the infected cucumber with powdery mildew enhanced the expression levels from1.6 to 47.3 fold of the defense genes PAL, PR3, PR1, Lox1, Lox 23, LecRK6.1, WRKY20, and Cupi4 compared to heathy cucumber. The results suggests the BABA induced defense response is associated with SA signal pathway-dependent systemic acquired resistance (SAR) in cucumber, which is involved in plant resistance mechanisms.

This study examines the synergistic interaction between the immunomodulatory functions of lactic acid bacteria postbiotics and the anti-inflammatory properties of Smilax China L. extract through a combined fermentation process. Using atopic dermatitis (AD) as a model, characterized by an immune imbalance that leads to skin inflammation, we developed a fermented product, MB-2006, and compared its effects to those of heat-killed probiotics, Lactobacillus acidophilus (LAC) and Lac-tobacillus rhamnosus (LRH). Our experiments focused on elucidating the mechanism of action of MB-2006 in AD-like HaCaT keratinocyte cells, particularly its impact on the NF-kB pathway, a pivotal regulator of inflammation. MB-2006 proved more effective in reducing inflammation markers such as IL-4 and thymic stromal lymphopoietin (TSLP), and in inhibiting NF-kB activation, compared to LAC and LRH. Significantly, MB-2006 also reduced the expression of thymus- and activation-regulated chemokine (TARC), highlighting a synergistic effect that enhances its thera-peutic potential. These results suggest that the combined fermentation of Smilax china L. extract with lactic acid bacteria enhanced both the anti-inflammatory and immunomodulatory effects, pre-senting a promising integrative approach to treating conditions like AD. Further studies are needed to validate these results in clinical settings and fully explore the potential of this synergistic fer-mentation process.

Sexual selection involving female choice or female preference (‘inter-sexual’ selection) or male-male competition (‘intra-sexual’ selection) is one of the key mechanisms for evolutionary diversification and speciation. In particular, sexual selection is recently suggested to be an important mode to drive the evolution of “novel” phenotype (i. e. “evolutionary novelty”). Despite extensive studies performed on sexually selected traits or male-specific ornaments (or weapon-like structures) with respect to their evolutionary origin and history and fitness benefits, relatively little is known about the molecular genetic mechanisms underlying their developmental process. However, with advances of genomic technologies (including whole transcriptome analysis using Next Generation Sequencing [NGS] techniques; RNA-Seq), progresses have been made to unveil the genetic background underpinning diverse sexually selected traits in different animal taxa. In the present review, we compile empirical data on the genes, genetic mechanisms or regulatory pathways underlying various sexually selected traits to explore whether the “common” genetic architectures shape the development and evolution of those traits across evolutionarily distant animal lineages. We show that the recruitment of pre-existing genetic network for a new purpose (i.e. gene network “co-option”) is rather widespread in the development and evolution of sexually selected traits, indicating that particular genes or gene-sets are repeatedly involved in different sexually selected traits. Information of genes or genetic mechanisms regulating the development of sexually selected traits would be an essential piece to complete a whole picture of the origin and evolution of sexually selected traits.

A new design scheme is proposed for twisting the walls of a microchannel, and its performance is demonstrated numerically. The numerical study was carried out for a T-shaped microchannel with twist angles in the range of 0 to 34π. The Reynolds number range was 0.15 to 6. The T-shaped microchannel consists of two inlet branches and an outlet branch. The mixing performance was analyzed in terms of the degree of mixing and relative mixing cost. All numerical results show that the twisting scheme is an effective way to enhance the mixing in a T-shaped microchannel. The mixing enhancement is realized by the swirling of two fluids in the cross section and is more prominent as the Reynolds number decreases. The twist angle was optimized to maximize the DOM, which increases with the length of the outlet branch. The twist angle was also optimized in terms of the relative mixing. The two optimum twisting angles are generally not coincident. The optimum twist angle shows a dependence on the length of the outlet branch but it is not affected much by the Reynolds number.

Abstract. Graphene family (GF)-Calcium phosphate (CaP) composites, holds great potential as components of bone regeneration materials. GF nanomaterials can be modified physically as well as chemically, which are to be biomimetic, mechanically to be hard due to their capability to support exceptional mechanical, thermal and electronic properties. These biocompatible GF composites coated on the calcium phosphate can enhance and tolerate stem cell growth and differentiation, proliferation into various lineages or interact with bioorganisms. The development in CF-CaP materials and their physicochemical/biointeractions and strategies towards osteoblasts is a great concern to promote faster healing and reconstructions of large bone imperfections or defects. In this review, we explain the influence of the CF-CaP and summarize recent developments on designing CF-CaP architectures as multifunctional bone regeneration platforms. We have also explored the typical biological applications concerning these CF-CaP based bioactive nanocomposites. Furthermore, the future viewpoints and evolving challenges will also be emphasized. Due to the shortage of full-length reviews in this emerging research field, this review would be caught great attention and encourage various new chances across a wider range of disciplines.

Over the past four decades, China has experienced a nutritional transition and has developed the largest population of internet users. In this study, we evaluated the impacts of internet access on the nutritional intake in Chinese rural residents. An IV-Probit-based propensity score matching method was used to determine the impact of internet access on nutritional intake. The data were collected from 10042 rural households in six Chinese provinces. The results reveal that rural residents with internet access have significantly higher energy, protein, and fat intake than those without. Chinese rural residents with internet access consumed 1.35% (28.62 kcal), 5.02% (2.61 g), and 4.33% (3.30 g) more energy, protein, and fat, respectively. There was heterogeneity as regards the intake of energy, protein, and fat among those in different income groups. Moreover, non-staple food consumption is the main channel through which internet access affects nutritional intake. The results demonstrate that the local population should use the internet to improve their nutritional status. Further studies are required to investigate the impact of internet use on food consumed away from home and micronutrients intake.

Fluorescence-linked immunosorbent assay (FLISA) is a commonly used, quantitative technique for detecting biochemical based on antigen–antibody binding reactions using a well-plate platform. With the developments in the manufacturing technology of microfluidic systems, FLISA can be implemented onto microfluidic disk platforms, which allows the detection of trace biochemical with high resolutions. Apart from requiring a lower proportion of reagent (1/10), this method also reduces the time required for the entire process to less than an hour. The incubation process involves antigen–antibody binding reactions as well as the binding of fluorogenic substrates to target proteins. The protocol for FLISA on a microfluidic platform necessitates the appropriate execution of liquid reagent movements during each step in order to ensure sufficient binding reactions. Herein, we propose a novel microfluidic disk comprising a 3D incubation chamber. Vascular endothelial growth factor as concentration with ng mL-1 is detected sequentially using a benchtop process employing this 3D microfluidic disk. The 3D microfluidic disk is implemented without requiring manual intervention or additional procedures for liquid control. During the incubation process, microbead movement is controlled through centrifugal force, generated due to disk rotation, and gravitational force via bead sedimentation on the sloped floor of the chamber.

The sensitivity of DNBR(Departure from Nucleate Boiling Ratio) values to approaches of subchannel control volume selection has been investigated for the TS01 and TS03 out of HIPER17 CHF(Critical Heat Flux) tests. In general, the coolant-centered subchannel method is applied to subchanel analyses for fuel bundle. When it comes to predicting for CHF of high quality region, however, the rod-centered subchannel method was better over high quality region. As a result, the rod-centered subchannel method were more suitable at a conservative point of view than the coolant-centered subchannel method comparing major properties. Also, it was confirmed that the radial subchannel locations at the minimum DNBR were similar when comparing both analysis results by two kind of methods.

Unavoidable exposure to radiosensitive normal tissues around cancerous tumor during the radiotherapy can cause side effects such as self-limited acute toxicities, mild chronic symptoms, or severe organ dysfunction. Nevertheless, clinical use of currently available radiation protective agents is limited because of their generic cytotoxicity. A study on radiation protective effect of delphinidin was conducted with proton-beam-exposed human colon cells (CCD-18Co). The measurement in changes of survival fractions of CCD-18Co with/without delphinidin administration at different radiation doses were measured by 3-[4,5-dimethylthiazol-2-yl]-2,5 diphenyl tetrazolium bromide (MTT) assay. The changes in expression of reactive oxygen species (ROS) and in activities of antioxidant enzymes were measured by colorimetric assays using pertinent assay kits. The measurement of pro-apoptosis/pro-survival protein expressions using Western blot assay and the measurement of DNA damage using comet assay were also fulfilled to evaluate the molecular level of radiation damages in CCD-18Co cells. The experimental results revealed that the pre-administration of delphinidin regulated antioxidant enzymes, reduced ROS, decreased DNA damage, regulated pro-apoptosis/pro-survival proteins, and eventually reduced apoptosis of CCD-18Co cells. In conclusion, it is claimed that delphinidin is nontoxic natural radiation protective compound, and thus delphinidin can be used to protect normal colon tissues during the proton beam therapy.

: In the automotive industry, high-strength plates have been increasingly used to reduce the vehicle body weight due to stringent regulations on fuel economy and safety. Such plates achieve tensile strengths as high as 1.5 GPa owing to the hot-stamping process. However, these plates suffer from scale generation and surface decarburization because of the surface oxidation of the material. Recently, studies on materials subjected to high-frequency induction heating have reported strength improvement owing to the coil shape and cooling method. This study presents the surface temperature changes, mechanical properties, and microstructures of boron steels subjected to longitudinal heating, which uses eddy currents generated from high-frequency induction heating. The surface temperature data were analyzed under different high-frequency induction heating powers (15, 18, 21, 24, 27, and 30 kW) and distances from the specimen (6, 9, and 15 mm). The mechanical properties and microstructures were also analyzed in different high-frequency induction heating coil directions. The correlations between the high-frequency induction heating power and the distance from the specimen with the maximum tensile strength were determined.

The low relative humidity (RH) levels in a greenhouse during the daytime in a strawberry (Fragaria × ananassa Duch) cultivation period negatively affect the growth of strawberry related to photo-physiology. Therefore, this study was conducted to confirm an efficient RH management method by analyzing the phenotypic characteristics related to photo-physiology by controlling the RH in a greenhouse during the daytime with a fog system. Strawberry plants were grown respectively in a greenhouse affected by natural RH changes (control) and in a greenhouse with 40% ~ 50% RH adjusted during the daytime using a fog system. In the greenhouse, with controlled RH, the temperature decreased, and the RH was higher in the initial growth stage of strawberry planting than the control. It was observed a significant increase in the survival rate of the strawberry plant, as well as the incidence of powdery mildew, was lowered. In addition, the photosynthetic rate and OJIP chlorophyll a fluorescence transients related to photosystem II efficiency of strawberry leaves were significantly higher in the fog treatment than in the control. In winter, during the day, the number of days on which the temperature dropped below 20℃ has increased, the greenhouse temperature with controlled RH was lower due to the fog system. When the yield per strawberry plant in January and February was investigated, the control was higher than the RH treatment. Therefore, RH management using a fog system must be controlled at a level where a temperature range is adequate for plant growth, in which the efficient control of these parameters increases strawberry productivity.

We explored the trends and the diversity of the mortality and risk factors of age-standardized cardiovascular diseases (CVD) and cerebrovascular disease (CBD) from 2000 to 2020 in five advanced Asian countries, including China, Japan, Singapore, South Korea, and Taiwan. Data were obtained from the Global Burden of Disease (GBD) report. Overall, the CVD mortality rates decreased gradually in all five Asian countries. Singapore had the highest rates before 2011, but Taiwan replaced Singapore as the nation of the highest mortality rates after 2012. Additionally, South Korea had the highest CBD mortality rates before 2016, while Taiwan experienced a peak in 2011 and remained high thereafter. The absolute difference (AD) and relative difference (RD) for CVD mortality rates showed clear declining trends in all five countries, with South Korea and China displaying the highest reductions, respectively. It is noteworthy that overweight and obesity exhibited an increasing trend in all these five Asian countries, with China demonstrating the highest AD and RD. Except for Taiwan, where a negative association of r=-0.732 was observed, CVD mortality was positively associated with CBD, hypertension, and DM mortality in all other four countries, therefore, further investigation into these relationships are needed.

There have been many discussions on the globalisation of SMEs, but it is true that there is not enough academic achievement after such the study of Born global (BG) ventures. The internationalisation of SMEs (Small and Medium Enterprises) is not easy because they lack resources or capabilities compared to multinational corporations. This study investigated the role of government in assisting the internationalisation of SMEs. In particular, SMEs lacked the ability to acquire market-oriented information, so we’ve established the scheme of efficient information support system for the internationalisation of SMEs. In other words, we proposed an information analysis system through the establishment of a relational database constructed for market-oriented information support. KISTI (Korea Institute of Science and Technology Information), which is one of the government-funded research institutes in the Republic of Korea, provided information support to the SMEs dealing with hydrazine related products. This study suggests this case for the market-oriented information support of the government in the internationalisation of SMEs. The research on information support of the government is meaningful in that it suggests a way to support SMEs in practical level.

This retrospective study aimed to assess coronary artery calcium (CAC) progression in serial computed tomography measurements according to risk factor changes. In 448 asymptomatic adults who underwent CAC measurements with more than one-year intervals, CAC progression was assessed according to age, sex, variable traditional risk factors (diabetes mellitus, hypertension, hyperlipidemia, and smoking), and initial CAC score (0, 0.1–100, and &gt;100). Univariate and multivariate logistic regression analyses were assessed for independent predictors of rapid CAC progression (△CAC/year&gt;20). During the 3.5-year follow-up, coronary artery calcifications occurred in 43 (12.8%) of 336 individuals with an initial CAC score of zero. Of 112 individuals with initial CAC presence, 60 (53.6%) had △CAC/year&gt;20. Age, male sex, body mass index, and all risk factors were significantly associated with △CAC/year&gt;20, but recently diagnosed hypertension (odds ratio [OR], 11.3) and initial CAC score (OR, 1.05) were significant independent predictors in multivariate regression analyses. CAC progression was affected by demographic and traditional risk factors, but adjusting for these factors, recently diagnosed hypertension and initial CAC score were the most influential factors for rapid CAC progression. These findings suggest that patients with higher initial CAC scores may benefit from more frequent follow-up scans and checks regarding risk factor changes.

Polypyrrole (PPy)-capped caped silver nanowire (Ag NW) nanomaterials (core–shell rod-shaped Ag NW@PPy) were synthesized suing a one–port suspension polymerization technique. The thickness of PPy layer on the 50-nm-thickness/15-μm-length Ag NW was effectively controlled to 10, 40, 50, and 60 nm. Thin films cast from one-dimensional conductive Ag NW@PPy formed a three-dimensional (3-D) conductive porous network structure and provided excellent electrochemical performance. The 3-D Ag NW@PPy network can significantly reduce the internal resistance of the electrode and maintain structural stability. As a result, a high specific capacitance of 625 F/g at a scan rate of 1 mV/s was obtained from the 3-D porous Ag NW@PPy composite film. The cycling performance over a long period exceeding 10,000 cycles was also evaluated. We expect that our core–shell-structured Ag NW@PPy composites and their 3-D porous structure network films can be applied as electrochemical materials for the design and manufacture of supercapacitors and other energy storage devices.

The decline in Pinus sylvestris var. mongolica in the introduction area has had a high profile in recent years. For the ecological restoration, management and silvicultural design of Mongolian pines in the introduction area, it is necessary to conduct a comprehensive and in-depth study on the ecological adaptation mechanism of Mongolian pines in provenances. The ecological process of water and nutrient accumulation as well as the influence of environmental factors on the photosynthetic physiology are the key to revealing the ecological adaptation mechanism of Mongolian pines. According to the differences of climate in the distribution area of Mongolian pines, sampling sites were set up, the effects of environmental factors on leaf δ13C and the relationship between leaf δ13C and nutrient content were analyzed. The results showed that leaf δ13C values were ranging from - 29.7 ‰ to - 23.76 ‰. The ecological stoichiometry, including LC (522.81 mg·g-1), LN (16.04 mg·g-1), LP (1.19 mg·g-1) and L-N:P (13.56), indicated that leaf photosynthesis and water use efficiency is greatly affected by environmental conditions, Mongolian pines had strong ability of carbon fixation, and its growth was obviously restricted by nitrogen. Although there was no significant correlation between δ13C with stoichiometric parameters in leaf, photosynthesis was the key link in the process of carbon fixation. It also showed that Pinus sylvestris var. mongolica was a stomatal limited plant. Leaf δ13C had significant correlation with climatic factors. VPD is the dynamic factor affecting the photosynthetic physiological process in leaves. Air and soil moisture are the dominate factors affecting the leaf stomatal conductance and determines leaf δ13C value, while other factors indirectly affect leaf δ13C by its impact on relative humidity or soil water content. Soil phosphorus content affected by clay is a key factor affecting soil water availability and soil nutrient cycling. Photosynthetic process in leaf is the dynamic process affecting the nutrient accumulation.

Advances in reconfigurable liquid-based reconfigurable antennas are enabling new possibilities to fulfil the requirements of more advanced wireless communication systems. In this review, a comparative analysis of various state-of-the-art concepts and techniques for designing reconfigurable antennas using liquid is presented. First, the electrical properties of different liquids at room temperature commonly used in reconfigurable antennas are identified. This is followed by a discussion of various liquid actuation techniques in enabling high frequency reconfigurability. Next, liquid-based reconfigurable antennas in literature used to achieve the different types of reconfiguration will be critically reviewed. These include frequency-, polarization-, radiation pattern- and compound reconfigurability. The current concepts of liquid-based reconfigurable antennas can be classified broadly into three basic approaches: altering the physical (and electrical) dimensions of antennas using liquid, applying liquid-based sections as reactive loads; and implementation of liquids as dielectric resonators. Each concept and their design approaches will be examined, outlining their benefits, limitations, and possible future improvements.

Water resources provided by alpine glaciers are an important pillar for people living in the arid regions in the west of China. In this study, the HBV (Hydrologiska Byrans Vattenavdelning) light model was applied to simulate glacier mass balance and runoff in the Koxkar River Basin (KRB) on the south slope of Mt. Tumur, western Tianshan Mts.. Daily temperature and precipitation were calculated by multiple linear regressions and gradient-inverse distance weighting, respectively, based on in-situ observed data by automatic weather stations (AWSs) in the basin (2007–2009) and at four meteorological stations neighbering the basin (1959–2009). Observed daily air temperature and precipitation were taken as input data for the HBV model, which was calibrated using runoff in 2007/08 and 2009/10, and validated in 2008/09 and 2010/11. Generally, the model could simulate runoff very well. The annual glacier mass balance and runoff were calculated using the HBV model driven by interpolated meteorological data for the period of 1959–2009. The simulated glacier mass balance were reasonable when compared with those observed values at nearby glaciers, indicating a decrease trend of mass balance in the basin with an average value of –370.4 mm a^-1 since 1959. The annual runoff showed a slight increase trend (5.51 mm a^-1). Futher analysis indicated that the runoff is more sensitive to temperature than precipitation amuont in the Koxkar river basin.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

Transposable elements (TEs), also known as mobile elements (MEs), are interspersed repeats that constitute a major fraction of the genomes of higher organisms. As one of their important functional impacts on gene function and genome evolution, TEs participate in regulating the expression of genes nearby and even far away at transcriptional and post-transcriptional levels. There are two known principal ways by which TEs regulate expression of genes. First, TEs provide cis-regulatory sequences in the genome with their intrinsic regulatory properties for their own expression making them potential factors for regulating the expression of the host genes. TE-derived cis-regulatory sites are found in promoter and enhancer elements, providing binding sites for a wide range of trans-acting factors. Second, TEs encode for regulatory RNAs with their sequences showed to be present in a substantial fraction of miRNAs and long non-coding RNAs (lncRNAs), indicating the TE origin of these RNAs. Furthermore, TEs sequences were found to be critical for regulatory functions of these RNAs including binding to the target mRNA. TEs thus provide crucial regulatory roles by being part of cis-regulatory and regulatory RNA sequences. Moreover, both TE-derived cis-regulatory sequences and TE-derived regulatory RNAs, have been implicated to provide evolutionary novelty to gene regulation. These TE-derived regulatory mechanisms also tend to function in tissue-specific fashion. In this review, we aim to comprehensively cover the studies regarding these two aspects of TE-mediated gene regulation, mainly focusing on the mechanisms, contribution of different types of TEs, differential roles among tissue types, and lineage specificity, based on data mostly in humans.

The dynamic factors in the environment violate the static environment assumption of the SLAM algorithm, leading to a decrease in the accuracy of camera positioning. In recent years, many studies have attempted to address dynamic objects by combining semantic constraints and geometric constraints, but issues such as poor real-time performance, the potential for mistakenly treating humans as rigid objects, and subpar performance in high-dynamic scenes still persist. This paper proposes a dynamic scene visual SLAM algorithm called Dynamic SLAM based on target tracking and multi-view geometry (TKG-SLAM), based on object detection, Kalman filters, and multi-view geometry. This algorithm takes into consideration both real-time performance and algorithm accuracy. It combines semantic constraints and multi-view geometry constraints, selectively running the algorithm in different scenarios, filtering and preserving static points for camera pose estimation. Experimental results demonstrate that, compared to current state-of-the-art dynamic SLAM methods, our approach achieves optimal performance in some scenarios and exhibits stronger real-time capabilities.

In this work antiparasitic peptidomimetics inhibitors (PEP) of falcipain-3 (FP3) of Plasmodium falciparum (Pf) have been proposed using structure-based and computer-aided molecular design. Beginning with the crystal structure of PfFP3-K11017 complex (PDB ID: 3BWK), three-dimensional (3D) models of FP3-PEPx complexes with known activities (IC50exp) were prepared by in situ modification, based on molecular mechanics and implicit solvation to compute Gibbs free energies (GFE) of inhibitor-FP3 complex formation. This resulted in a quantitative structure-activity relationships (QSAR) model based on a linear correlation between computed GFE (ΔΔGcomp) and the experimentally measured IC50exp: (pIC50exp=-(IC50exp/109) =-0.4517×∆∆Gcomp+4.0865 ; R2 = 0.89). Apart from the structure-based relationship, a ligand-based quantitative pharmacophore model (PH4) of novel PEP analogs where substitutions were directed by comparative analysis of the active site interactions was derived using the proposed bound conformations of the PEPx. This provided structural information useful for the design of virtual combinatorial libraries (VL), which was virtually screened based on the 3D-QSAR PH4. The end results were predictory inhibitory activities falling within the low nanomolar concentration range.

The world is currently experiencing COVID-19, one of the worst pandemics that have happened in this century, affecting 10.7 million people worldwide. It has caused massive growth in the number of employees working from home. However, employees have minimal cybersecurity resources unlike organizations with security teams protecting them against attacks. Hence, cybersecurity plays an important role as users can be easily targeted by cybercriminals. This paper examines how cyberattacks have increased during this pandemic and shows how greatly they have affected health organizations, individuals and social networking applications. Results of the attacks include data breaches, false announcements and operations being disrupted. Attacks occurring during this pandemic and how they were handled are also critically discussed. The existing contributions do touch on related attacks but do not provide in-depth solutions regarding the issues. Even though there are many works and findings that were done previously, technology is ever evolving. Therefore, we need to be well versed with current and future issues and provide the latest mechanisms to prevent cybersecurity threats from occurring. On our share, we intend to present our findings on the challenges being faced by the population and its increasing threats as well as presenting unique solutions that can help organizations or related persons understand or spread awareness on the importance of cybersecurity. Through the research performed in this paper, it is found that there are many ways these issues can be alleviated. However, the issue is that there is significant lack of action and investment in terms of actual implementation and application of the available solutions.

Globally,coastal regions are vital areas of human activities and, as such, are centres of population growth and urban and economic development. Long-term human development has had a major impact on the ecological environment of coastal zones. Therefore, exploring the distribution and provenance of marine sediment types in coastal areas heavily influenced by human activities can provide scientific evidence and references for the current and future ecological management of these sensitive environments. For this reason, we have conducted an analysis on the sediment grain size, Endmember, organic matter content and geochemical elements in the Lu’erhuan River‒Malan Island‒Sandun Island area in the eastern part of Qinzhou Bay, a region heavily influenced by human activities. Sediment grain size clearly differs throughout the study site and the material provenances and hydrodynamic conditions are also varied, likely due to the local environmental conditions and the significant impact human activities have had on the area. The finest-grained sediment is imported from either inland or coastal areas via rivers and weak tidal currents, the next finest component is input from coastal areas through weak tidal currents, and the moderately coarse component mainly originates from nearby beaches. The two coarsest-grained sediment components are influenced by the combination of human activities, tidal currents and waves and enter the water via erosion. Organic matter provenance resembles that of the sediment components, exhibiting varied characteristics. This is due to the combination of natural and human activities in the bay. The organic matter in the upper reaches of the Lu’erhuan River originates from the river and coastal paddy fields, with obvious terrigenous characteristics; the organic matter in northern Malan Island mainly comes from external sources related to oyster farming; while organic matter in eastern Sandun Island is mainly produced endogenously by marine plankton. Al, Ti, Fe, Mg, K, Ga and other elements indicate that terrestrial sediments are significantly disturbed by human activities. However，Mn reflects the marine distribution of terrestrial sediments from the Lu’erhuan River to Jishuimen. Ca and Sr, indicators of marine sediments, are distributed in the eastern offshore area of Sandun Island, which is connected to the open waters. Due to the influence of human activities, As and Cd are highly enriched in the study area, while Cu is less affected by human activities.

Lignin fibers typically influence the mixture performance of stone matrix asphalt (SMA), such as strength, stability, durability, noise level, rutting resistance, fatigue life, and water sensitivity. However, limited studies were conducted to analyze the influence of fibers on the percent voids in mineral aggregate in bituminous mixture (VMA) during the mixture design. This study analyzed the effect of different fibers and fiber contents on the VMA in SMA mixture design. A surface-dry condition method test and Marshall Stability test were applied on the SMA mixture with four different fibers (i.e., flocculent lignin fiber, mineral fiber, polyester fiber, blended fiber). The test results indicated that the bulk specific gravity of SMA mixtures and asphalt saturation decreased with the increasing fiber content, whilst the percent air voids in bituminous mixtures (VV), Marshall Stability and VMA increased. Mineral fiber had the most obvious impact on the bulk specific gravity of bituminous mixtures, while flocculent lignin fiber had a minimal impact. The mixture with mineral fiber and polyester fiber had significant effects on the volumetric properties, and, consequently, exhibited better VMA over the conventional SMA mixture with lignin fiber. Modified fiber content range was also provided, which will widen the utilization of mineral fiber and polyester fiber in the applications of SMA mixtures. The mixture evaluation suggested no statistically significant difference between lignin fiber and polyester fiber on the stability. The mineral fiber required a much larger fiber content to improve the mixture performance than other fibers. Overall, the results can be a reference to guide SMA mixture design.

As the necessity for safety and aesthetic of nightscape have arisen, the importance of nightscapes (i.e., nighttime landscape) planning has garnered the attention of mainstream consciousness. Therefore, this study is to suggest the guideline for nightscape planning using electroencephalography (EEG) technology and survey for recognizing the characteristics of a nightscape. Furthermore, we verified the EEG method as a tool for landscape evaluation. This study analyzed the change of relative alpha power and relative beta power and self-reporting of participants in order to investigate the correlation between EEG and fear according to twelve nightscape settings. Our findings indicated the corresponding measures of fear vary accordance with whether there was people or not, and the environmental settings (Built Nightscape Images; BNI vs Natural Nightscape Images; NNI). Based on our physiological EEG experiment, we provided a new analytic view of the nightscape. The approach we utilized enables a deeper understanding of emotional perception and fear among human subjects by identifying the physical environment which impacts how they experience nightscapes.

In this study, the efficiencies of flat-plate and U-tube solar collectors were investigated experimentally when an Al₂O₃ nanofluid was used as a working fluid and compared to those of solar collectors using water. The energy saving and CO₂ and SO₂ generated were calculated and compared to those of solar collectors using water. In addition, based on the experimental results, an economic analysis of the use of solar collectors in various countries was performed. As the concentration of the Al₂O₃ nanofluid increased, the performance of the solar collector improved. The highest efficiency for the solar collectors was shown at the concentration of 1.0 vol% with the nanoparticle size of 20 nm. The maximum efficiencies of the flat-plate and U-tube solar collectors using 1.0 vol%-Al₂O₃ nanofluid with 20-nm nanoparticles was 74.9% and 72.4%, respectively, when the heat loss parameter was zero. The efficiencies of the flat-plate and U-tube solar collectors using Al₂O₃ nanofluid were 14.8% and 10.7 higher, respectively, than those using water. When 50 EA flat-plate solar collectors were operated for one year using Al₂O₃ nanofluid, the coal use, generated CO₂, and generated SO₂ were 189.99 kg, 556.69 kg, and 2.03 kg less than those of solar collectors using water, respectively. In addition, the largest electricity cost reduction was in Germany.

Based on the 5.7-magnitude earthquake that stroke Songyuan (China) and 172 groups of liquefaction data collected in mainland China, the hyperbolic liquefaction discriminant formula originally proposed by Sun Rui was revised, and a new formula for the liquefaction of sand was put forward. Groups of data derived from the Bachu earthquake in Xinjiang and an earthquake that occurred in New Zealand (47 and 195 groups, respectively) were used to carry out a back-judgment test, then, the results were compared with those of the existing standard method. Overall, the results showed that the new formula for hyperbolic liquefaction discrimination compensates for the conservative liquefaction discrimination of the older formula; moreover, it has a good applicability to different intensities, groundwater levels, and the deep sand layer of the Songyuan site, reflected by a more balanced success rate. Therefore, combining the existing liquefaction discrimination methods and the research results of discrimination, it is necessary to establish a suitable regional identification method through the continuous accumulation of liquefaction data and expanding database.

Acute ischemic strokes are the third leading cause of death and the leading cause of neurological disability worldwide. The oxygen and glucose deprivation associated with ischemic strokes not only leads to neuronal cell death, but also increases the inflammatory response and decreases functional output of the brain. The only intervention approved by US Federal Drug and Food Administration for treatment of ischemic strokes is tissue plasminogen activator (tPA), however, such treatment can only be given within 4.5 hours of the onset of stroke-like symptoms. This narrow time-range limits its application, and it also might induce detrimental rather than beneficial effects to stroke patients by treatment of the tPA. In order to reduce the infarct volume of an acute ischemic stroke while increasing the time period for treatment, emerging therapies reveal great potential by targeting inflammation, growth factors, ion channels, and neurotransmitter receptors with monoclonal antibody (MAB). With successfully application in the treatment of cancer patient by MAB, in this review, we will focus on recent advances on stroke therapy by using MAB on the treatment of stroke by targeting inflammation, growth factors, ion channels, and neurotransmitter receptors. Therefore, developing specific MAB targeting the signaling pathway of stroke will contribute to stroke therapy.

The concept of transit-oriented development (TOD) has been widely recognized in recent years for its role in reducing car traffic, improving public transportation, and enhancing traffic sustainability. This paper conducts empirical research on a developed rail transit network, using Shanghai as a case study. In addition to traditional TOD features, other factors based on urban rail transit are introduced, including multi-level modeling (MLM), which is used to analyze the possible factors influencing rail patronage. To avoid the bias of research results led by the correlation between independent variables, factors are divided into two levels. The first level includes three groups of variables: the built environment, station characteristics, and socioeconomic and demographic characteristics. The second level includes a set of variables which are regional characteristics. Results show that the most significant impact on train patronage is station location in the business district area. Other factors that have a positive effect on promoting rail transit travel include the number of service facilities around the station, degree of employment around the station, economic level, intensity of residential development, if the station is a transfer station, the operating period of the station, and the size of the large transportation hub around the station.

Climate change and the increasing frequency of high-temperature events are significant threats to global crop yields. To address this, a comprehensive understanding of how plants respond to heat shock (HS) is essential. Signaling pathways involving calcium (Ca2+), a versatile second messenger in plants, encode information through temporal and spatial variations in ion concentration. Ca2+ is detected by Ca2+-sensing effectors, including channels and binding proteins, which trigger specific cellular responses. At elevated temperatures, the cytosolic concentration of Ca2+ in plant cells increases rapidly, making Ca2+ signals the earliest response to HS. In this review, we discuss the crucial role of Ca2+ signaling in raising plant thermotolerance and we explore its multifaceted contributions to various aspects of the plant HS response.

In this article we compute many topological indices for the family of Möbius ladder. At first we give general closed form of M-polynomial of this family and recover many degree based topological indices out of it. We also compute Zagreb indices and Zagreb polynomials of this family.

Owing to their unique physicochemical properties, nanoparticles are used in a variety of ways in the field of cancer treatment, including imaging, drug delivery, and photothermal and photodynamic therapies. The fascinating properties of nanoparticles are determined by their size, morphology, and constituent elements, and various synthetic methods and post-synthetic techniques have been applied to control these factors. Herein, we present examples of shape and composition control through galvanic replacement, a technique that exploits redox potential differences between elements to induce spontaneous ion-exchange and highlight its specific contributions to cancer treatment applications. The present article identifies the recent advances in nanoparticle formation techniques and discusses the future outlook of the field.

The black hole (BH) phenomenon is an intraluminal restenotic lesion. It was identified by intravascular ultrasound (IVUS) and optical coherence tomography (OCT) after intracoronary brachytherapy and drug-eluting stent implantation. Despite the similarity in the mode of action of brachytherapy and drug-eluting stent implantation, the BH phenomenon appears to be uncommon after drug-eluting stent implantation. Specifically, the BH phenomenon is better identified by OCT than by IVUS. Herein, we present a case of in-stent restenosis with suspected BH phenomenon on IVUS confirmed by OCT.

Addressing real-time aircraft target detection in microsatellite-based visible light remote sensing video imaging requires considering the limitations of imaging payload resolution, complex ground backgrounds, and the relative positional changes between the platform and aircraft. These factors lead to multi-scale variations in aircraft targets, making high-precision real-time detection of small targets in complex backgrounds a significant challenge for the detection algorithms. Hence, this paper introduces a real-time aircraft target detection algorithm for remote sensing imaging using an improved lightweight attention mechanism that relies on the YOLOv7 framework (SE-CBAM-YOLOv7). The proposed algorithm replaces the standard convolution (Conv) with a lightweight convolutional SEConv to reduce the computational parameters and accelerate the detection process of small aircraft targets, thus enhancing real-time onboard processing capabilities. Besides, the SEConv-based SPPCSPC (Spatial Pyramid Pooling and Connected Spatial Pyramid Convolution) module extracts image features. It improves detection accuracy while the feature fusion section integrates the CBAM hybrid attention network, forming the CBAMCAT module. Furthermore, it optimizes small aircraft target features in channel and spatial dimensions, improving the model's feature fusion capabilities. Experiments on public remote sensing datasets reveal the proposed SE-CBAM-YOLOv7 improves detection accuracy by 3% and mAP value by 4.2% compared to YOLOv7, significantly enhancing the detection capability for small-sized aircraft targets in satellite remote sensing imaging.

The measurement range of a conventional current sensor is narrow because it is used with signals relative to the rated values of the measurement range from a voltage-type device. Consequently, multiple current sensors must be used in accordance with the measurement range. To address this problem, this paper proposes a new current sensor with a clamp-shaped part for low current measurement and a simple straight structure for high current measurement. The output signals of the proposed current sensor are amplified with a Hall element using the magnetic force of a rectangular air gap inside the clamp. To verify the characteristics of the proposed current sensor, a current was applied to an external load, and the value determined by the current sensor noted. Then, electromagnetic field analysis was performed through current sensor modeling and the results obtained compared to the actual sensor results. The proposed sensor had a 1% linearity in the output signals and exhibited dynamic characteristics over a wide current range.

Precision and accuracy estimation is an important index used to reflect the measurement performance and quality of a measurement system. To reveal the significance and connotations of the precision and accuracy estimation index of a close-range photogrammetry system, several common precision and accuracy estimation methods used in close-range photogrammetry are explained from a theoretical perspective, and the mechanism of the internal coincidence precision estimation and the external coincidence accuracy estimation are deduced, respectively. Through detailed experimental design and testing, the validity and reliability of the proposed precision and accuracy estimation methods are verified, which provides strong evidence for the quality control, optimisation, and evaluation of the measurement results from a close-range photogrammetry system. At the same time, it has significance for the further development of precision and accuracy estimation analysis of close-range photogrammetry systems.

Abstract: Global ecological concern regarding the transfer of fouling organisms to ship hulls is increasing. This study investigated the species composition, dominant species, distribution patterns, community structure, and life-cycle differences of hull-fouling macroinvertebrates on five research vessels (R/Vs: Isabu, Onnuri, Eardo, Jangmok 1, and Jangmok 2) operated by the Korea Institute of Ocean Science and Technology (KIOST). Hull-fouling macroinvertebrates were collected three to five times on quadrats from the upper and middle sectors of the hull sides, bottom, and niche areas (the propellers and shafts and the thrusters). A total of 47 macroinvertebrate species were identified, represented by 8,519 individuals(ind.)/m2 and a biomass of 1,967 gWWt/m2 on the five vessels. The number of species, density, and biomass were greater on the coastal vessels the Eardo, Jangmok 1, and Jangmok 2 than on the ocean-going vessels the Isabu and Onnuri. Among the coastal vessels, barnacles were the most abundant and had the greatest density, while mollusks had the highest biomass. Differences between hull sectors showed that the highest species abundance and density appeared on all hulls in ports and bays where the Jangmok 1 operated, while the highest species abundance, density, and biomass were identified in the niche areas of the Eardo, which operated farther from the coast. The hull-fouling macroinvertebrates that exceeded 1% of all organisms were the barnacles Amphibalanus amphitrite, Balanus trigonus, and Amphibalanus improvisus; the polychaete Hydroides ezoensis; the bivalves Magallana gigas and Mytilus galloprovincialis; and the amphipod Jassa slatteryi. The dominant species were cosmopolitan and globally distributed, and many of them were cryptogenic. Six native species were identified: M. gigas, H. ezoensis, the amphipod Melita koreana, the isopod Cirolana ko-reana, and the barnacle B. trigonus and F. kondakovi. Eight non-indigenous species (NIS) were de-tected: barnacles A. amphitrite and A. improvisus, the bivalve M. galloprovincialis, the polychaete Perinereis nuntia, amphipods J. slatteryi and Caprella californica, and bryozoans Bugulina californica and Bugula neritina. Of the fouling macroinvertebrates found on the vessel hulls, 13% were native and 17% were NIS. The nMDS ordination analysis of the five vessels showed four clusters of fouling macroinvertebrate communities: two ocean clusters (the Isabu and Onnuri), one coastal cluster (the Eardo and Jangmok 2), and one local cluster (the Jangmok 1). More diverse communities developed on the hulls of vessels that operated locally rather than globally or in deep oceans. Spearman rank correlation showed that biological indices such as number of species, density, and biomass correlated highly and positively with the numbers of days on coastal operations and negatively with the number days on ocean operations. The species diversity index correlated positively with the total number of anchoring days and coastal operation days and negatively with the total number of operation days and ocean operation days. The macroinvertebrates differed by the area of operation, the port of anchorage, the number of days in operation and at anchor, and the hull sectors. There is no previous research data on hull-fouling macroinvertebrates in the Republic of Korea, and this study provides a basis for future studies to identify introduced species and their differences based on operation area.

Industrial process control systems commonly exhibit features of time-varying, strong coupling, and strong nonlinearity. Obtaining accurate mathematical models of these nonlinear systems and achieving satisfactory control performance is still a challenging task. In this paper, data-driven modeling techniques and deep learning methods are used to accurately capture a category of smooth nonlinear system’s spatiotemporal features. The operating point of these systems may change over time, and their nonlinear characteristics can be locally linearized. We established the LSTM-CNN-ARX model by utilizing a fusion of long short-term memory (LSTM) network and convolutional neural network (CNN) to fit the coefficients of the state-dependent exogenous variable autoregressive (SD-ARX) model. Compared to other models, the hybrid LSTM-CNN-ARX model is more effective in capturing the nonlinear system’s spatiotemporal characteristics due to its incorporating the strengths of LSTM for learning temporal characteristics and CNN for capturing spatial characteristics. The model-based predictive control (MPC) strategy, namely LSTM-CNN-ARX-MPC, is developed by utilizing the model's local linear and global nonlinear features. The control comparison experiments conducted on a water tank system (WTS) show the effectiveness of the developed models and MPC methods.

Due to wood’s susceptibility to fire, it is crucial to treat wood-based materials with flame retardants, especially in construction applications. This study investigated the effectiveness of various grooving types, including transverse, longitudinal, both transverse and longitudinal, and surface grooving, in enhancing larch's vacuum pressure impregnation process. The results revealed that transverse grooving provided a slightly greater impregnation advantage than longitudinal grooving. Moreover, exceptional impregnation performance was observed in larch samples subjected to both longitudinal and transverse grooving and surface grooving, exhibiting a remarkable improvement of 214,7 % compared to untreated larch.

Antibiotics’ effect on Mycoplasma pneumoniae (MP) infection still remains controversial. A prospective study of 257 children with MP pneumonia during a recent epidemic (2015-2016) was conducted. All MP pneumonia patients were treated with corticosteroids within 24-36 h after admission. Initially, oral prednisolone (1 mg/kg) or intravenous methylprednisolone (IVMP) (1-2 mg/kg) was administered for mild pneumonia patients, and IVMP (5 -10 mg/kg/day) for severe pneumonia patients. If patients showed persistent fever for 36-48 hours or disease progression, additive IVMP (5 mg/kg or 10 mg/kg) was given. Eighty-five patients received only a broad-spectrum antibiotic without macrolide. The mean age and the male:female ratio were 5.6 ± 3.1 years, respectively. Seventy-four percent of patients (190/257) showed immediate defervescence within 24 h, and 95.7% (246/257) of patients showed defervescence within 72 h with improvements in clinical symptoms. Eight patients who received additive IVMP also showed clinical improvement within 48 h without adverse reactions. There were no clinical or laboratory differences between patients treated with a macrolide (n = 172) and without (n = 85). Early corticosteroid therapy might reduce disease morbidity and prevent disease progression in MP pneumonia patients without side effects, and antibiotics may have limited effects on MP infection.

Passive and forced drinking harm was prevalent but less recognized in Chinese adolescents. We educated adolescents on such harm to reduce their intention to drink. Students (n=1244) from 7 secondary schools in Hong Kong participated in a video-based health talk on passive and forced drinking harm. Paired t-test was used to assess their change in knowledge of passive and forced drinking, health and social harm of drinking after the health talk. McNemar's chi-squared test and adjusted multivariable logistic regression (AOR) were used to assess their change in intention to drink and intention to quit. Students were less likely to drink (OR 0.29, 95% CI 0.19-0.42) and more likely to quit drinking (OR 3.50, 1.10-14.6) after the health talk. Increased knowledge of passive drinking was associated with less intention to drink (AOR 0.93, 0.90-0.97), increased knowledge of health harm (adjusted b 0.06, 0.05-0.08), and social harm of drinking (adjusted b 0.12, 0.10-0.16). Similar associations were observed in forced drinking (intention to drink: AOR 0.87, 0.79-0.96; health harm: adjusted b 0.16, 0.12-0.19; social harm: adjusted b 0.36, 0.28-0.43). We showed preliminary evidence that the health talk on passive and forced drinking reduced the intention to drink in adolescents.

Background: Fingertip injuries with volar pulp tissue defects are challenging to manage due to the complex anatomy and critical role of the fingertip in sensory and motor functions. Traditional surgical approaches are associated with donor site morbidity, prolonged immobilization, and suboptimal functional outcomes. This study aimed to evaluate the efficacy of a conservative treatment protocol using artificial dermis and semi-occlusive dressing for these injuries. Methods: A single-center, prospective study was conducted on 31 patients with fingertip injuries involving volar pulp defects. The treatment protocol involved wound debridement, application of artificial dermis (Pelnac®), and semi-occlusive dressing (IV3000®). Outcomes were assessed using subjective questionnaires and objective measures, including fingerprint regeneration, sensory function, pain, and cosmetic appearance. The impact of injury characteristics on outcomes and treatment duration was evaluated. Complications were recorded, and patient satisfaction was assessed. Results: The mean treatment duration was 45.29 days (SD=17.53), with no significant differences based on injury characteristics. Complications were minimal, with only one case (3.22%) directly attributable to the treatment. Fingerprint regeneration was considerable (mean score=2.58, SD=0.67), with slightly better scores in bone-exposed injuries. Sensory disturbances were minimal, with no significant differences across injury types. Post-treatment pain was low (mean=0.45, SD=0.67), and cosmetic satisfaction was high (mean=4.09, SD=0.94). Overall patient satisfaction was high (mean=4.41, SD=0.67), regardless of injury severity. Discussion: This study demonstrates the efficacy of a conservative approach using artificial dermis and semi-occlusive dressing for fingertip injuries with volar pulp defects. The treatment protocol achieved favorable outcomes in tissue regeneration, sensory recovery, pain management, and cosmetic appearance while minimizing complications and morbidity associated with traditional surgical interventions. The high patient satisfaction across all injury types highlights the patient-centered nature of this approach. Conclusions: The conservative treatment protocol using artificial dermis and semi-occlusive dressing is a promising strategy for managing fingertip injuries with volar pulp defects. This approach harnesses the body's regenerative potential, minimizes surgical morbidity, and achieves excellent functional and aesthetic outcomes. Further research is needed to optimize treatment protocols and investigate long-term outcomes.