During the hand-eye calibration process of the manipulator, the Euclidean distance error of the calibration results cannot be calculated because the true values of the hand-eye conversion matrix cannot be obtained. In this paper, a new method of projection error analysis is presented. Error analysis is carried out by using a priori knowledge that the location of AR markers is fixed in the calibration process. The coordinates of the AR marker center point are reprojected to the pixel coordinate system, and then compared with the true pixel coordinates of the AR marker center point obtained by corner detection or manual labeling in order to obtain the Euclidean distance between the two coordinates as the basis for error analysis. Experimental results show that the proposed optimization method can greatly improve the accuracy of hand-eye calibration results.

Here, we present a series of novel block copolymers (BCP) from bio-derived monomers, poly(lactic acid)-block-poly(2,5-furandimethylene succinate) (PLA-b-PFS), in which the furan groups from PFS block can be crosslinked with bis(maleimido) triethylene glycol (M2) through a Diels-Alder reaction. This dynamic crosslinking reaction leads to a network structure for enhancing the mechanical properties compared to their linear BCP analogous. Decreasing the crosslinking density leads to a decrease of glass transition temperature of BCPs and a transition from glassy to rubbery-like behavior at room temperature. This allows a wide tunablity of both elastic moduli and yields of the materials. For the lowest crosslinking density. the material exhibits an over 50% self-healing efficiency at room temperature after five days, attributed to the low Tg (15.2 C) from the introduction of PFS block, allowing sufficient chain mobility for structure re-organization. Moreover, with the appropriate selection of crosslinking density (PLA-b-PFS/M2 (6/1)), it also shows an excellent shape memory property with a high recovery rate of 96.3% and a fixity rate of 97.3%. The permanent shape can be rewriteable due to the reversibility of Diels-Alder reaction. With these advanced functionalities and ease in large-scale fabrication, the PLA-b-PFS/M2 shows great promises for self-healing coatings or films with shape memory properties in a wide variety of applications such as packaging materials

Multi-rotor drones, a kind of unmanned equipment which is widely used in military, commercial consumption and other fields, has been developed very rapidly in recent years. However, their short flight time has hindered the expansion of their application range. This can be addressed by utilizing hydrogen fuel cells, which exhibit high energy density, strong adaptability to ambient temperature, and no pollution emissions, as the power source. Accordingly, the application of hydrogen fuel cells as the power source in multi-rotor drones is a promising technology that has attracted significant research attention. This paper summarizes the development process of hydrogen fuel cell mul-ti-rotor drones and analyzes the key obstacles that need to be addressed for the further development of hydrogen fuel cell multi-rotor drones, including structural lightweight, hydrogen storage methods, energy management strategies. Additionally, prospects for the future development of hydrogen fuel cell multi-rotor drones are presented.

Infrared thermography has already been proven to be a significant method in non-destructive evaluation since it gives information with immediacy, rapidity and low cost. However, the thorniest issue for wider application of IRT is the quantification. In this work, we proposed a specific depth quantifying technique by employing the Gated Recurrent Units (GRU) in composite material samples via pulsed thermography (PT). Carbon Fiber Reinforced Polymer(CFRP) embedded with flat bottom holes were designed via Finite Element Method (FEM) modeling in order to precisely control the depth and geometrics of the defects. The GRU model automatically quantified the depth of defects presented in the CFRP material. The proposed method evaluated the accuracy and performance of synthetic CFRP data from FEM for defect depth predictions.

Biotic and abiotic factors influence the formation of fungal-algal pairings in lichen symbiosis. It is poorly known which factors determine the specific associations, especially when distantly related fungi are considered. Here, we investigated the effect of different drivers on the association patterns of taxonomically diverse lichenized fungi and their trebouxioid symbiotic partners. In 200 samples collected across three biomes, we found 41 species of lichenized fungi, associating with 16 species of trebouxioid green algae, of which 62% were previously unreported. Species identity of the fungal and algal partner had the greatest effect on the outcome of the symbiosis compared with abiotic factors such as climatic variables and geographic distance. Partner specificity was found to be higher in tropical regions than in temperate and arctic regions. Co-phylogenetic analyses indicated congruent phylogenies of trebouxioid algae and associated fungi, rejecting their random associations. Evolutionary mechanisms contributing most to the observed phylogenetic patterns were ‘loss’ and ‘failure to diverge’ of the algal partners. This study broadens our knowledge of fungi-algae symbiotic patterns in view of Trebouxia-associated fungi.

This paper briefly reviews the state of the art in artificial intelligence including inductive and deductive methods. Deep learning and ensemble machine learning lie in inductive methods while automated reasoning implemented in deductive computer languages (Prolog, Otter, and Z3) is based on deductive methods. In the inductive methods, intelligence is inferred by pseudorandom number for creating the sophisticated decision trees in Go (game), Shogi (game), and quiz bowl questions. This paper demonstrates how to wisely use the pseudorandom number for solving coin-weighing puzzles with the deductive method. Monte Carlo approach is a general purpose problem-solving method using random number. The proposed method using pseudorandom number lies in one of Monte Carlo methods. In the proposed method, pseudorandom number plays a key role in generating constrained solution candidates for coin-weighing puzzles. This may be the first attempt that every solution candidate is solely generated by pseudorandom number while deductive rules are used for verifying solution candidates. In this paper, the performance of the proposed method was measured by comparing with the existing open source codes by solving 12-coin and 24-coin puzzles respectively.

Saikosaponin (SS) a is a compound with various pharmacological properties and easily degraded into SSb1 and SSg in acid condition. In present work another two new degradation products of SSa formed under acid hydrolytic condition were detected and isolated by analytical and semi-preparative liquid chromatography technology, furthermore their structures were characterized as hydroxyl-saikosaponin a and SSb2 by spectral analysis, which is not only essential in stability-indicating method development and validation but also could be used as a worst case to assess the analytical method performance of SSa. Moreover their structural transformation pathways were also proposed.

The application of organic fertilizers plays a crucial role in achieving carbon sequestration in the agricultural sector. This paper discusses how farmers can more smoothly promote organic fertilizer extension services. An evolutionary game model is developed to describe the conflicting interests of Chinese farmers and local governments in organic fertilizer extension services, and the dynamic evolution of the game players and the influence of parameter adjustment on the strategic choices of both parties is presented. In this paper, the game model and the main results are validated with the help of simulation tools, and a sensitivity analysis of the selected parameters is performed. The results show that (1) the implementation of subsidy policy is less helpful for organic fertilizer extension services; (2) The ideal event probability of the game was found to be positively related to the cost of applying inorganic fertilizers, additional benefits to farmers, political returns to local governments, and penalties for not using organic fertilizers; (3) This is important for improving the performance of local governments, reducing government regulatory costs, improving policy support for organic fertilizer extension services, and reducing the cost of implementing organic fertilizer extension services.

The central nervous system (CNS) is the final frontier in drug delivery because of the blood-brain barrier (BBB), which poses significant barriers to the access of most drugs to their targets. Kynurenic acid (KYNA), a tryptophan (Trp) metabolite, plays an important role in behavioral functions and abnormal KYNA levels have been observed in neuropsychiatric conditions. The current challenge lies in delivering KYNA to the CNS owing to its polar side chain. Recently, C-3 side chain modified KYNA analogs have been shown to cross the BBB; however, it is unclear whether they retain the biological functions of the parent molecule. This study examined the impact of KYNA analogs, specifically SZR-72, SZR-104, and the newly developed SZRG-21, on behavior. The analogs were administered intracerebroventricularly (i.c.v.), and their effects on the motor domain were compared with those of KYNA. Specifically, open field (OF) and rotarod (RR) tests were employed to assess motor activity and skills. SZR-104 increased horizontal exploratory activity in the OF test at a dose of 0.04 μmol/4 μL, while SZR-72 decreased vertical activity at doses of 0.04 and 0.1 μmol/4 μL. In the RR test, however, neither KYNA nor its analogs showed any significant differences in motor skills at either dose. Side chain modification affects affective motor performance and exploratory behavior, as the results show for the first time. In this study, we showed that KYNA analogs alter emotional components such as motor-associated curiosity and emotions. Consequently, drug design necessitates the development of precise strategies to traverse the BBB while paying close attention to modifications in their effects on behavior.

Neurodegeneration is a major problem in neuroscience and medicine as it causes and worsens many neurological and psychiatric disorders. It involves gradual loss of neurons at different levels of the brain, affecting cognition, emotion, behavior, consciousness, and attention. Understanding the causes and consequences of neurodegeneration is crucial for identifying the risk factors, biomarkers, and treatments. However, the current therapies are mostly symptomatic and ineffective. Therefore, new and innovative methods, such as noninvasive brain stimulation (NIBS), are needed to modulate brain activity and plasticity in a safe and reversible manner. This field is rapidly developing, with a focus on exploring new clinical applications, mechanisms, and combinations of NIBS and drugs. This special issue covers the latest progress and challenges in the study of neurodegeneration in cognitive impairment and mood disorders from the experimental, clinical, and translational perspectives. It addresses the complexity and diversity of these conditions, the lack of disease-modifying treatments, the ethical and practical issues of conducting research in vulnerable and diverse populations, the integration and interpretation of data from multiple sources and modalities, and the development and validation of novel methods such as NIBS, artificial intelligence, and drug repurposing. Collaborative efforts among various stakeholders are needed to improve our knowledge and treatment of neurodegeneration underlying cognitive impairment and mood disorders.

In many countries, increasing concern for animal welfare is driving retailer commitments and government legislation that aim to improve the lives of farmed fish. One aspect of fish welfare involves stunning fish prior to slaughter. The feasibility of stunning depends on the species of fish and physical farm characteristics. In this article, we provide an overview of stunning before slaughter in European sea bass and sea bream aquaculture, one of the largest finfish farming industries in the developed world that does not yet stun most of its production. Sea bass and sea bream stunning necessitates the use of electrical stunning equipment aboard harvest vessels, often a significant distance from the shoreline; this presents an interesting engineering and policy challenge. Together, Türkiye, Greece, Spain, and Italy produced over 400,000 t of sea bass and sea bream in 2020. In Türkiye and Greece, farms are numerous and located very close to the shoreline. In Spain and Italy, farms are few and located far from the shoreline. The highest average production is found in farms from Türkiye (1,000 t) and Spain (1,300 t, and lower average production is found in Greece (300 t) and Italy (350 t). Producer progress towards the installation of electrical stunning appears comparatively well-developed for Türkiye, Spain, and Greece, though we emphasise that producers and other stakeholders require continued support to realise this opportunity. Producers in Italy appear slower to make progress on this aspect of animal welfare and may require additional support.

Delve into the dynamic realms of neuroscience, neurology, and psychiatry with this groundbreaking editorial, unveiling the intricate mechanisms of brain function and dysfunction. Explore the latest advancements in molecular biology, genetics, epigenetics, pharmacology, and neuroimaging that are revolutionizing our understanding of neurological and psychiatric disorders. Uncover the challenges and gaps in translating cutting-edge research into practical clinical applications, aiming to enhance the lives of patients and their families. Discover the pivotal role of neuroplasticity in reshaping the brain's adaptability throughout life, alongside the promising potential of non-invasive brain stimulation techniques like transcranial magnetic stimulation and transcranial direct current stimulation. Embark on a journey of innovation and collaboration as researchers and clinicians strive to bridge the gap between bench and bedside, offering hope for improved diagnosis, prevention, and treatment of complex neurological and psychiatric conditions. Join us in this exploration of transformative ideas and novel interventions that hold the key to a brighter future for individuals and society.

This paper addresses a new micromechanical model to predict biaxial tensile moduli of plain weave fabric (PWF) composites by considering the interaction between the orthogonal interlacing strands. The two orthogonal yarns in micromechanical unit cell (UC) were idealized as the curved beams with a path depicted by using sinusoidal shape functions. The biaxial tensile moduli of PWF composites were derived by means of the minimum total complementary potential energy principle founded on micromechanics. The biaxial tensile tests were respectively conducted on the RTM-made EW220/5284 PWF composites at five biaxial loading ratios of 0, 1, 2, 3 and ∞ to validate the new model. The predictions from the new model were compared with experimental data and good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed model. Using the new model, the biaxial tensile moduli of plain weave fabric (PWF) composites could be predicted based only on the properties of basic woven fabric.

The quantified residence time distribution (RTD) provides a numerical characterization of mixing in the continue casting tundish, thus allowing the engineer to better understand the metallurgical performance of the reactor. This paper describes a computational fluid dynamic (CFD) modelling study for analyzing the flow pattern and the residence time distribution in a five-strand tundish. Two passive scalar transport equations are applied to separately calculate the E-curve and F-curve in the tundish. The numerical modelling results are compared to the water modelling results for the validation of the mathematical model. The volume fraction of different flow regions (plug, mixed and dead) and the intermixing time during the ladle changeover are calculated to study the effects of the flow control device (FCD) on the tundish performance. The result shows that a combination of the U-baffle with deflector holes and the turbulence inhibitor has three major effects on the flow characteristics in the tundish: i) reduce the extent of the dead volume; ii) evenly distribute the liquid streams to each strand and iii) shorten the intermixing time during the ladle changeover operation.

Teachers’ time resources are becoming increasingly scarce and time poverty will have a direct impact on the long-term sustainability of their professional development. However, the current state of teachers’ time poverty and its potential harmful consequences are unclear. Therefore, this research conducts two cross-sectional studies to investigate the current situation and group differences in time poverty among Chinese teachers (Sample 1), as well as the influence of teachers’ time poverty on job burnout (Sample 2). The results indicate that: (1) there is a high level of time poverty among teachers; (2) there is no significant difference in gender, teaching years, or teaching section, and there is a significant difference in teaching responsibilities; (3) time poverty could positively and significantly predict job burnout, and job burnout could positively and significantly predict mental health; (4) mental health factors (including depression, anxiety and stress) play the mediating role in the relationship between teachers’ time poverty and job burnout. To create a sustainable development environment for teachers, it is suggested that teachers improve time management skills and establish a self-regulation mechanism; schools should clarify the boundaries of teachers’ work and respect their right to rest; and society should provide positive and adequate spiritual support.

The increasing trend of studying the innate softness of robotic structures and amalgamating it with the benefits of the extensive developments in the field of embodied intelligence has led to sprouting of a relatively new yet extremely rewarding sphere of technology. The fusion of current deep reinforcement algorithms with physical advantages of a soft bio-inspired structure certainly directs us to a fruitful prospect of designing completely self-sufficient agents that are capable of learning from observations collected from their environment to achieve a task they have been assigned. For soft robotics structure possessing countless degrees of freedom, it is often not easy (something not even possible) to formulate mathematical constraints necessary for training a deep reinforcement learning (DRL) agent for the task in hand, hence, we resolve to imitation learning techniques due to ease of manually performing such tasks like manipulation that could be comfortably mimicked by our agent. Deploying current imitation learning algorithms on soft robotic systems have been observed to provide satisfactory results but there are still challenges in doing so. This review article thus posits an overview of various such algorithms along with instances of them being applied to real world scenarios and yielding state-of-the-art results followed by brief descriptions on various pristine branches of DRL research that may be centers of future research in this field of interest.

Health issues of children with intellectual disabilities (ID) have gained significant attention as a key focus of China health goals. This study aimed to compare the differences in displacement skills and problem behaviors among children with varying degrees and types of ID, while also exploring their relationship. The study included 90 participants who were children with ID and had completed TGMD-2 displacement skills and Strengths and Difficulties Questionnaire (SDQ) assessments. Covariance, partial correlation, and multiple linear regression analyses were conducted to examine the differences and correlations between these factors. The findings revealed that higher severity of intellectual disability was associated with lower scores in locomotor skills and increased manifestation of problem behaviors. Notably, there were significant variations in locomotor skills and problem behaviors among children with different types of intellectual disabilities. There is a positive correlation between locomotor skills and problem behaviors in children with intellectual disabilities, where locomotor skills can predict the occurrence of problem behaviors. In Conclusion, the research confirms that the development of locomotor skills can have a positive impact on the accompanying problem behaviors of children with developmental disabilities.

The task of weakly supervised point cloud semantic segmentation has received widespread attention and also has been widely used in autonomous driving, robotics, and modern industries. Due to the high dimensionality and large volume of point cloud data, many technical difficulties appeal to weakly supervised semantic processing, especially segmentation. However, weakly-supervised schemes usually provide only partial labelling information of the underlying point cloud data and thus need to effectively extract local features, geometric information, and contextual relationships only using these limited labelled data for supervised learning. To improve weakly-supervised semantic segmentation, we propose a novel segmentation network through the boundary-based feature aggregation based on a K-NN algorithm with down-sampling operation, and also introduce the smoothness loss and Siamese loss for effective segmentation. The experiments on public datasets demonstrate that our presented segmentation method exceeds most of the existing fully supervised and weakly-supervised methods in terms of mIoU. Specifically, our network has high segmentation accuracy on the labels of objects with similar geometrical structures, such as ceiling, wall, floor, chair and table, reaching 91.2%, 98.8%, 83.3%, 75.3% and 80.2%, respectively. Extensive experiments also illustrate its robustness, effectiveness, and generalization of the proposed weakly supervised segmentation network.

The Mara River basin (MRB) has a world-famous ecosystem, but the vegetation has been damaged due to economic development in recent years, and there is little known about the area that will experience severe vegetation damage in the future. Based on the vegetation vulnerability system, principal component analysis, and three CMIP6 scenarios (SSP1-2.6, SSP2-4.5, SSP5-8.5), vegetation vulnerability was calculated in the base period (2010-2019), near-term period (2020-2059) and long-term period (2060-2099) in the MRB. The spatial cluster of vegetation vulnerability was revealed by spatial correlation analysis, and the transition of vegetation vulnerability of different periods was analyzed by stochastic matrix. The results showed that in all periods, the vulnerability showed a high-high cluster in the east, and a low-low cluster midstream and downstream. From the stochastic matrix, the area of high vulnerability increased the least under the SSP1-2.6, while it increased the most under the SSP5-8.5. The vegetation vulnerability upstream increased the most from the base period to the near-term period and long-term period in the MRB. By comparing the vegetation vulnerability under different scenarios, and pointing out the areas with the highest vulnerability increase, this study can better provide comprehensive decision-making for vegetation protection in the MRB.

Thermal fluctuations in two-dimensional (2D) isotropy systems at non zero finite temperatures can destroy the long-range (LR) magnetic order due to Mermin-Wanger theory. Interestingly, the magnetic anisotropy related to spin-orbit coupling (SOC) could stabilize magnetic order in 2D systems. Recently, 2D FexGeTe2 (3≤x≤7) with high curie temperature (TC), as a typical 2D van der Waals metallic ferromagnet, has not only made significant progress in synthetic methods and controlling ferromagnetism (FM), but also actively explored many device applications. In this Review, we introduce six experimental methods, ten ferromagnetic modulation strategies, and three spintronic devices of 2D FexGeTe2 materials. Overall, we have outlined the challenges and potential research directions in this field.

The microstructure evolution during the cold rolling and subsequent annealing of Alloy 800H was investigated. Two distinct rolling methods, unidirectional rolling and cross-rolling, were intro-duced. Results show that better ductility was observed in the unidirectional rolling than in cross-rolling, whilst a higher volume fraction of large deformed grains was observed in the cross-rolled plates than in the unidirectionally rolled plates. Recrystallization occurred faster in plates from unidirectional rolling than from cross-rolling.

We propose Reduced Collatz Conjecture that is equivalent to Collatz Conjecture, which states that every positive integer can return to an integer less than it, instead of 1. Reduced Collatz Conjecture should be easier because some properties are presented in reduced dynamics, rather than in original dynamics (e.g., ratio and period). Reduced dynamics is a computation sequence from starting integer to the first integer less than it, and original dynamics is a computation sequence from starting integer to 1. Reduced dynamics is a component of original dynamics. We denote dynamics of x as a sequence of either computations in terms of ``I'' that represents (3*x+1)/2 and ``O'' that represents x/2. Here 3*x+1 and x/2 are combined together, because 3*x+1 is always even and followed by x/2. We formally prove that all positive integers are partitioned into two halves and either presents ``I'' or ``O'' in next ongoing computation. More specifically, (1) if any positive integer x that is i module $2^t$ (i is an odd integer) is given, then the first t computations (each one is either ``I'' or ``O'' corresponding to whether current integer is odd or even) will be identical with that of i. (2) If current integer after t computations (in terms of ``I'' or ``O'') is less than x, then reduced dynamics of x is available. Otherwise, the residue class of x (namely, i module $2^t$) can be partitioned into two halves (namely, i module $2^{t+1}$ and $i+2^t$ module $2^{t+1}$), and either half presents ``I'' or ``O'' in intermediately forthcoming (t+1)-th computation.

In this paper, under the symmetric entropy and the scale squared error loss functions, we consider the maximum likelihood (ML) estimation and Bayesian estimation of the Shannon entropy and Rényi entropy of the two-parameter inverse Weibull distribution. In the ML estimation, the dichotomy is used to solve likelihood equation. In addition, the approximation confidence interval is given by the Delta method. Because the form of estimation results is more complex in the Bayesian estimation, the Lindley approximation method is used to achieve the numerical calculation. Finally, Monte Carlo simulations and a real data set are used to illustrate the results derived. By comparing the mean square error between the estimated value and the real value, it can be found that the performance of ML estimation of Shannon entropy is better than that of Bayesian estimation, and there is no significant difference between the performance of ML estimation of Rényi entropy and that of Bayesian estimation.

BACKGROUND: Chronic hepatitis B infected with Hepatitis B virus remains a major health concern worldwide. Despite standard interferon-α and nucleotide analogues have been shown to reduce the deterioration of liver disease among chronic hepatitis B patients, covalently closed circular DNA was still difficult to eradicate. METHODS: A literature search of Pubmed and Web of science was performed with the following key words: ‘CRISPR’, ‘CRISPR/Cas9’, ‘hepatitis B’, ‘HBV’, ‘chronic hepatitis B’ and ‘HBV cccDNA’. The information about CRISPR/Cas9 for the treatment of HBV cccDNA or hepatitis B was reviewed. RESULTS: CRISPR/Cas9 could treat hepatitis B through suppressing or clearing HBV cccDNA with different gRNAs. CONCLUSION: With the emergence of CRISPR/Cas9 (the RNA-guided clustered regulatory interspaced short palindromic repeats, CRISPR) editing technology, clearance of hepatitis B virus and better prevention of liver carcinoma seemed to be possible.

High density of buildings and the large traffic volume of cities give rise to narrow spaces and high passenger flows in most subway stations. When evacuation is required during an emergency, these problems may trigger issues in operational safety. Therefore, it is imperative to comprehensively assess subway station emergency evacuation times and capacities during the operating process to ensure the design is safe, science-based, and rational. To further enhance safe evacuation capacity, this paper proposes an overall evacuation time model that considers the multielement charac-teristics of subway stations in multiple segments. The evacuation route is decomposed into five stages according to the critical nodes in the evacuation process. An overall emergency evacuation time model is established based on the diversity of bottlenecks in the five stages, integrating elements such as the horizontal movement velocity of passengers, subway equipment parameters, and human density. Taking Xi’an Wulukou Subway Station as an example, this paper verifies the outcomes of the theoretical model against the Pathfinder software and conducts additional anal-yses of the evacuation conditions of stairs and exits. The results show that the error between the theoretical emergency evacuation time and simulation evacuation time was 5.4%, The emergency evacuation model established in this study boasts strong robustness and stability.

Abstract: Microstructural and mechanical properties of the eutectic Sn58Bi and micro-alloyed Sn57.6Bi0.4Ag solder alloys were compared. With the addition of Ag micro-alloy, the tensile strength was improved and this is attributed to a combination of microstructure refinement and an Ag3Sn precipitation hardening mechanism. However, ductility is slightly deteriorated due to the brittle nature of the Ag3Sn intermetallic compounds (IMCs). Additionally, a board level reliability study of Ag micro-alloyed Sn58Bi solder joints produced utilising a surface-mount technology (SMT) process, were assessed under accelerated temperature cycling (ATC) conditions. Results reveal that micro-alloyed Sn57.6Bi0.4Ag has a higher characteristic lifetime with a narrower failure distribution. This enhanced reliability corresponds with improved bulk mechanical properties. It is postulated that Ag3Sn IMCs are located at the Sn-Bi phase boundaries and suppress the solder microstructure from coarsening during the temperature cycling, hereby extending the time to failure.

In the neuroscience research field, specific for medical imaging analysis, how to mining more latent medical information from big medical data is significant for us to find the solution of diseases. In this review, we focus on neuroimaging data that is functional Magnetic Resonance Imaging (fMRI) which non-invasive techniques, it already becomes popular tools in the clinical neuroscience and functional cognitive science research. After we get fMRI data, we actually have various software and computer programming that including open source and commercial, it's very hard to choose the best software to analyze data. What's worse, it would cause final result imbalance and unstable when we combine more than software together, so that's why we want to make a pipeline to analyze data. On the other hand, with the growing of machine learning, Python has already become one of very hot and popular computer programming. In addition, it is an open source and dynamic computer programming, the communities, libraries and contributors fast increase in the recent year. Through this review, we hope that can make neuroimaging data analysis more easy, stable and uniform base the one platform system.

The theory of water transport in trees, according to which the main driving force of water movement is the suction created by the evaporation of water by the meniscus (the curved surface of the capillary liquid column) on the evaporating elements, supported from below by root pressure, is flawed. The capillary effect in nature is around one meter. In the case of open-air gaps, the leaf cannot suck in the water against gravity because, in this case, the plant would not be sucking in water, but air through the open-air gap. If not, how do trees transport water? When evaporation occurs, there is no suction towards the canopy, but pressure is due to a reduction in the cross-section of the water pipe caused by heat loss through evaporation. At night, when evaporation stops, a thermal equilibration process is triggered, which restores the original cross-section of the pipe. This generates suction and draws water from the soil. As the hydrostatic pressure in the pipe is high for tall trees, the pipe is cut off. To prove my theory, I have given several examples. Water transport is not based on physical mechanical laws alone. There may be complex physiological, biochemical, and biophysical processes behind the operation of the pipe system.

Determining accurate PM2.5 pollution concentrations and understanding their dynamic patterns is crucial for scientifically informed air pollution control strategies. Traditional reliance on linear correlation coefficients for ascertaining PM2.5 related factors only uncovers superficial relationships. Moreover, the invariance of conventional prediction models restricts their accuracy. To enhance the precision of PM2.5 concentration prediction, this study introduces a novel integrated model that leverages feature selection and a clustering algorithm. Comprising three components - feature selection, clustering, and integrated prediction, the model first employs the non-dominated sorting Genetic Algorithm (NSGA-III) to identify the most impactful features affecting PM2.5 concentration within air pollutants and meteorological factors. This step offers more valuable feature data for subsequent modules. The model then adopts a two-layer clustering method (SOM+K-means) to analyze the multifaceted irregularity within the dataset. Finally, the model establishes the Extreme Learning Machine (ELM) weak learner for each classification, integrating multiple weak learners using the Adaboost algorithm to obtain a comprehensive prediction model. Through feature correlation enhancement, data irregularity exploration, and model adaptability improvement, the proposed model significantly enhances the overall prediction performance. Data sourced from 12 Beijing-based monitoring sites in 2016 were utilized for an empirical study, and the model's results compared with five other predictive models. The outcomes demonstrate that the proposed model significantly heightens prediction accuracy, offering useful insights and potential for broadened application to multifactor correlation concentration prediction methodologies for other pollutants.

This investigation delves into an examination of the growth dynamics observed in Central Taiwan Science Park (CTSP) and Silicon Glen in Scotland, with a specific focus on their energy, environmental, and economic management. The aim is to predict and evaluate the latest advancements and applications of technology. In terms of energy, CTSP focuses on Taiwan's supply security and green transformation challenges, while Silicon Glen emphasizes Scotland's wind energy generation technologies. Both regions are committed to the development of renewable energy and smart grids. Regarding environmental aspects, CTSP and Silicon Glen prioritize environmental protection and sustainable development by implementing measures for environmental monitoring. In terms of economic management, CTSP, and Silicon Glen serve as key technology industry hubs This investigation delves into an examination of the growth dynamics observed in Central Tai-wan Science Park (CTSP) and Silicon Glen in Scotland, with a specific focus on their energy, environmental, and economic management. The aim is to predict and evaluate the latest advancements and applications of technology. In terms of energy, CTSP focuses on Taiwan's supply security and green transformation challenges, while Silicon Glen emphasizes Scotland's wind energy generation technologies. Both regions are committed to the development of renewable energy and smart grids. Regarding environmental aspects, CTSP and Silicon Glen prioritize environmental protection and sustainable development by implementing measures for environmental monitoring. In terms of economic management, CTSP, and Silicon Glen serve as key technology industry hubs in Taiwan and Scotland, respectively, attracting numerous high-tech and startup enterprises. Various means facilitate the growth of industries and foster innovations in different industrial spheres. Important factors contributing to this growth include policy support, availability of research materials, and provision of infrastructure. This research paper compares the successful case studies of two industrial parks, along with their environmental and economic management strategies. It explores the management principles that ensure the sustainable development and economic growth of industrial parks, aiming to assist decision-makers and relevant stakeholders in evaluating the sustainable development planning of industrial parks.

COVID-19 is a pandemic with no cure. There is an urgent need for low-cost interventions. Macroclimate work through affecting microclimate. In many situations, man-made microclimate, such as air conditioning, may override the effect of natural macroclimate in determining SARS-CoV-2 pathogenicity. Ambient temperature (AT) has been roughly associated to SARS-CoV-2 transmission. To translate into a feasible practice in controlling COVID-19 pandemic, in-depth and implementable knowledge of AT role in SARS-CoV-2 transmission should be unveiled. This study aimed to determine if there is a ‘safe’ temperature that is comfortable to human beings while significantly inhibitory for SARS-CoV-2 pathogenicity. Data on monthly new deaths or new cases per million population (MDPM or MCPM) and monthly cumulated days with more cases than the previous day (DI) from March 2 to June 30, 2020 were collected from all 118 countries with population over five million. Monthly average AT negatively correlated with the transmission parameters. A significant decrease in transmission was observed when AT reached above 20 ºC. Monthly average (not average high) AT of countries with MDPM <2, MCPM<10, or DI<=7 was found to be between 24.54 and 26.89 ºC (25.18 ºC on average) with average standard error of 4.81. Thus, average AT <20, 20-25, >25 ºC were considered as high, medium, and low risk AT. Furthermore, MDPM in countries with AT <20 ºC were 80.93, 50.23, 13.52, and 5.05 times of those in countries with AT >25 ºC in March, April, May, and June, respectively. MDPM low-risk rates (<2) in countries with AT >25 ºC were 100, 83.33, 52.73, and 52.46%, respectively. In countries with AT <20 ºC, the trends were opposite. Setting indoor temperature to 25 ºC could decrease the need of social distancing for containing SARS-CoV-2 transmission. Ventilation and sanitizing the air with ultraviolet light in nonbusiness hours may be additionally effective. Cooling indoor temperature too low may be a reason of COVID-19 outbreak in some high AT countries. Authorities and the general population can evaluate COVID-19 risk level and manipulate microclimate to reduce the risk anywhere anytime based on local day average AT.

Variations in the implant thread shape and occlusal load behavior may result in significant changes in the biological and mechanical properties of dental implants and surrounding bone tissue. Most previous studies consider a single implant thread design, an isotropic bone structure, and a static occlusal load. However, the effects of different thread designs, bone material properties, and loading conditions are important concerns in clinical practice. Accordingly, the present study performs Finite Element Analysis (FEA) simulations to investigate the static, quasi-static and dynamic response of the implant and implanted bone material under various thread designs and occlusal loading directions (buccal-lingual, mesiodistal and apical). The simulations focus specifically on the von Mises stress, displacement, shear stress, compressive stress and tensile stress within the implant and the surrounding bone. The results show that the thread design and occlusal loading rate have a significant effect on the stress distribution and deformation of the implant and bone structure during clinical applications. Overall, the results provide a useful insight into the design of enhanced dental implants for an improved load transfer efficiency and success rate.

As a potential motivation, psychological empowerment stimulates employees' work behaviors, and it determines the degree of effort and duration of employees' work. Only when employees are psychologically empowered, will they have an impact on their behavior when they believe that they are trusted. This paper chose to set the independent variable as the employee's perceived trust and the dependent variable as the company's work performance, and explored the mediating role of psychological empowerment in the two. The psychological empowerment of employees had a positive impact on work performance. Employees with high psychological empowerment tended to be proactive in their work, and had more input in the work, which in turn encouraged employees to have higher work performance. The four dimensions of psychological empowerment can positively affect employee task performance, and the ability and influence of psychological empowerment had a positive impact on relationship performance. Psychological empowerment as a whole perception played a part of the mediating role between the perception of superior dependency and task performance, and it played a part of the mediating role between perception of superior dependency and relationship performance. As a whole perception, psychological empowerment played a part of mediating role between perceived information disclosure and task performance, and part of mediating role between perceived information disclosure and relationship performance. In the study of perceived trust and work performance, this article focused on the mediating role of psychological empowerment, and further understood the internal mechanism of perceived trust.

Infrared thermography has already been proven to be a significant method in non-destructive evaluation since it gives information with immediacy, rapidity, and low cost. However, the thorniest issue for the wider application of IRT is quantification. In this work, we proposed a specific depth quantifying technique by employing the Gated Recurrent Units (GRU) in composite material samples via pulsed thermography (PT). Finite Element Method (FEM) modeling provides the economic examination of the response pulsed thermography. In this work, Carbon Fiber Reinforced Polymer (CFRP) specimens embedded with flat bottom holes are stimulated by a FEM modeling (COMSOL) with precisely controlled depth and geometrics of the defects. The GRU model automatically quantified the depth of defects presented in the stimulated CFRP material. The proposed method evaluated the accuracy and performance of synthetic CFRP data from FEM for defect depth predictions.

Background: The scaffold protein tyrosine kinase substrate 4 (TKS4) undergoes tyrosine phos-phorylation by the epidermal growth factor receptor (EGFR) pathway via Src kinase. The TKS4 deficiency in humans is responsible for the manifestation of a genetic disorder known as Frank-Ter Haar syndrome (FTHS). Based on our earlier investigation, the absence of TKS4 triggers migration, invasion, and epithelial-mesenchymal transition (EMT)-like phenomena while concurrently suppressing cell proliferation in HCT116 colorectal carcinoma cells. This indicates that TKS4 may play a unique role in the progression of cancer. In this study, we demonstrated that the enhancer of zeste homolog 2 (EZH2) and the histone methyltransferase of polycomb repressive complex 2 (PRC2) are involved in the migration, invasion, and EMT-like changes in TKS4-deficient cells (KO). EZH2 is responsible for the maintenance of the trimethylated lysine 27 on histone H3 (H3K27me3). Methods: We performed the transcriptome sequencing, chromatin immunoprecipitation, protein and RNA quantitative studies, cell mobility, invasion, and proliferation studies combined with/without EZH2 activity inhibitor 3-deazanoplanocine (DZNep) Results: We detected an elevation of global H3K27me3 levels in the TKS4 KO cells, which could be reduced with treatment with DZNep, an EZH2 inhibitor. Inhibition of EZH2 activity reversed the phenotypic effects of the knockout of TKS4, reducing the migration speed and wound healing capacity of the cells as well as decreasing the invasion capacity, while the decrease in cell prolif-eration became stronger. In addition, inhibition of EZH2 activity also reversed most epithelial and mesenchymal markers. We investigated the wider impact of TKS4 deletion on the gene expression profile of colorectal cancer cells using transcriptome sequencing of wild-type and TKS4 knockout cells, particularly before and after treatment with DZNep. Additionally, we observed changes in the expression of several protein-coding genes and long non-coding RNAs that showed a recovery in expression levels following EZH2 inhibition. Conclusions: Our results indicate that the removal of TKS4 causes a notable disruption in the gene expression pattern, leading to the disruption of several signal transduction pathways. Inhibiting the activity of EZH2 can restore most of these transcriptomics and phenotypic effects.

Oxygen evolution reaction (OER) is a key half-reaction in electrocatalytic water splitting. Large-scale water electrolysis is hampered by the commercial precious metal-based OER electrocatalysts owing to their high cost and slow kinetics. To address these issues, we present a facile one-pot room-temperature coprecipitation method to quickly synthesize carbon nanotubes-interconnected amorphous NiFe-layered double hydroxides (NiFe-LDH@CNT) as low-cost, efficient and stable OER electrocatalyst. NiFe-LDH@CNT hybrid catalyst delivers outstanding OER performance with a low onset overpotential of 255 mV and a small Tafel slope of 51.2 mV dec-1, as well as outstanding long-term stability. The terrific catalytic capability of NiFe-LDH@CNT can be associated with the synergistic effects of its room-temperature synthesized amorphous structure, bi-metallic modulation, and conductive CNT skeleton. The room-temperature synthesis can not only offer economic feasibility, but also obtain amorphous NiFe-LDH without crystalline boundaries, facilitating long-term stability during OER process. The bi-metallic nature of NiFe-LDH guarantees a modified electronic structure, providing additional catalytic sites. Simultaneously, the highly conductive CNT network fosters a nanoporous structure, facilitating electron transfer, O2 release and enriching catalytic sites. This study presents a strategy to purposefully design nanoarchitecture and facilely synthesize amorphous transition metal-based OER catalysts, ensuring the cost effectiveness, production efficiency, and long-term stability.

Demolished concrete and plastic waste are two increasingly aggravating problems. In this study, a novel method was proposed to simultaneously recycle concrete and plastic wastes by compacting concrete and plastic powders together under pressure and temperature. The influence of compression pressure and temperature as well as the mixture proportion on the bending strength of specimens was investigated. The results showed that pressure and temperature had a positive effect on the specimen strength; however, the molding temperature should not exceed the melting temperature of plastic. The proportion of plastic had a minimal effect on the bending strength of the specimen when plastic accounted for 25%–75% of the overall mass of the test piece.

The editorial explores the realm of emerging translational research in neurology and psychiatry, providing insights into various subjects, including neurodegenerative disorders and innovative therapeutic methods. The main objective is to study neurological and psychiatric disorders, such as Alzheimer's disease, with a particular emphasis on techniques for neural regeneration and repair. The editorial highlights the importance of taking a comprehensive approach to studying and treating complex neurological and psychiatric conditions. This involves thoroughly reviewing research papers on the causes, development, biomarkers, and treatment options for these conditions. The editorial emphasizes the necessity of using multidisciplinary and integrative methods to gain a deeper understanding and improve the treatment of these conditions. The development of an animal model for recurrent primary dysmenorrhea showcases the innovative techniques employed in the investigation of gynecological disorders, illustrating the capacity of translational research to connect fundamental scientific knowledge with practical medical applications. The cooperative endeavors of researchers and clinicians emphasized in this editorial lay the foundation for revolutionary advancements that hold the potential to enhance outcomes for individuals afflicted with neurological and psychiatric disorders globally.

This study employs the phase-field regularized cohesion model (PF-CZM) to simulate crack propagation and damage behavior in porous granite. We investigate how pore radius (r), initial crack-pore distance (D), and pore-crack angle (θ) impact crack propagation. The simulation findings reveal that, with a fixed deflection angle and initial crack-pore distance, larger pores are more likely to induce crack extension under identical loading conditions. Moreover, with r and θ keeping constant, the crack extension can be divided into two stages: from its initiation to the lower edge of the pore and then from the lower edge to the upper boundary of the model. By varying the values of D and r, we derive multiple combinations of different D/r ratios and pore radii. These results demonstrate that with constant r, cracks tend to deflect toward the pore closer to the initial crack. Conversely, when D is maintained constant, cracks will preferentially deflect toward pores with a larger r. In summary, the numerical simulation of rock pores and initial cracks, based on the PF-CZM, exhibits remarkable predictive capabilities and holds significant potential in advancing rock fracture analysis.

Chronic renal failure (CRF) is a major public health problem worldwide. In this work, we investigated the effects of a purified Laminaria japonica polysaccharide (LJP61A) on the renal function using adenine-induced CRF mice model. Results exhibited that adenine treatment caused serious renal pathological damages and elevation of serum creatinine and blood urea nitrogen of mice. However, these changes could be significantly reversed by the administration of LJP61A in a dose-dependent manner. Additionally, LJP61A could dramatically reduce the weight loss, improve the urine biochemical index, and regulate the electrolyte disturbance of CRF mice. These results suggested that the renal functions of adenine-induced CRF mice could be improved by LJP61A, which might be developed to a potential therapeutic agent for CRF patients.

In this work, the Ni/Ti/Nb multilayer composite was successfully manufactured by accumulative pack-roll bonding. The microstructure evolution and mechanical properties of the composite during the accumulative roll bonding (ARB) process were investigated by scanning electron microscopy(SEM), energy dispersive spectrometer(EDS), transmission electron microscopy (TEM), micro-hardness and tensile tests. The results showed that after 5 passes of the ARB process, the deformations of layers were relatively uniform, and no large number of interlayer fractures occurred. The microstructures of Ni and Ti were both equiaxed grains with a grain size of 200 nm and 150 nm, respectively, and finer equiaxed grains of the Ni layer were observed at the interface. The laminar structure of Nb layer was observed. The tensile strength and micro-hardness increased significantly as the number of ARB increased. After 5 passes of the ARB process, the tensile strength of the composite reached 792.3 MPa, and the micro-hardness of Ni, Ti, and Nb were increased to 270.2, 307.4, and 243.4 HV, respectively.

Distributed/semi-distributed models are considered to be sensitive to the spatial resolution of the data input. In this paper, we take a small catchment in high urbanized Yangtze River Delta, Qinhuai catchment as study area, to analyze the impact of spatial resolution of precipitation and the potential evapotranspiration (PET) on the long-term runoff and flood runoff process. The data source includes the TRMM precipitation data, FEWS download PET data, and the interpolated metrological station data. GIS/RS technique was used to collect and pre-process the geographical, precipitation and PET series, which were then served as the input of CREST (Coupled Routing and Excess Storage) model to simulate the runoff process. The results clearly showed that, the CREST model is applicable to the Qinhuai catchment; the spatial resolution of precipitation had strong influence on the modelled runoff results and the metrological precipitation data cannot be substituted by the TRMM data in small catchment; the CREST model was not sensitive to the spatial resolution of the PET data, while the estimation fourmula of the PET data was correlated with the model quality. This paper focused on the small urbanized catchment, suggesting the influential explanatory variables for the model performance, and providing reliable reference for the study in similar area.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

The branch prediction units (BPUs) generally have security vulnerabilities, which can be used by attackers to obtain the execution status, jump directions, and jump address of conditional branches, and the existing protection methods cannot defend against these attacks. Therefore, this article proposes a hardware security protection method for conditional branches of embedded systems. This method calculates the number of updates to the branch target buffer (BTB). When it exceeds the threshold, BTB is locked to prevent attackers from analyzing the execution status of branches based on the time difference of whether BTB is updated. Moreover, the hybrid physical unclonable function (PUF) circuit is designed to provide confidentiality protection for the jump directions, jump addresses, and their indexes, preventing attackers from stealing these critical data. If these mechanism fails and attackers successfully tamper with conditional branches, this paper proposes a control flow integrity (CFI) protection mechanism based on branch labels to timely detect tampering with instruction codes, jump addresses, and jump directions. The proposed method is implemented and tested on FPGA. The experimental results show that this method can achieve fine-grained security protection for conditional branches, with about 5.4% resource overhead and less than 5.5% performance overhead.

Objective: To examine the effect of bilateral total lobectomy and unilateral total lobectomy on improving thyroid function in patients with thyroid micropapillary carcinoma treated with euthyrox. Methods: The study was conducted on 68 patients with thyroid micro papillary carcinoma treated with euthyroxwho had been surgically treated with euthyrox in our hospital between January 2018 and December 2019. On the basis of random number grouping, they were divided into control groups (n = 34, bilateral total lobectomy) and observation groups (n = 34, unilateral total lobectomy plus isthmectomy). Thyroid function, free triiodothyronine (FT3), thyroid hormone (TSH), and voice function (VHI score) of the two groups were compared.Results: In comparison to the control group, the observation group had shorter incision lengths, shorter operation times, and shorter hospital stays, as well as less intraoperative bleeding and drainage volume, and the difference was statistically significant (P < 0.05); As compared with the control group, the observation group had higher FT4 and FT3 levels as well as lower TSH levels, a statistically significant difference (P < 0.05).VHI scores of emotions, function, physiology, and other voice functions were significantly lower among the observation group than those of the control group (P < 0.05).Conclusion: A unilateral total lobectomy with adjacent isthmus resection in patients with thyroid micro papillary carcinoma can yield ideal results, accelerate the time taken for surgical rehabilitation, improve thyroid function, thereby improving voice quality, as well as improve the overall prognosis of the patient.

The essence of cross-modal generation and retrieval modeling for image-text interactions lies in semantic consistency. Among these, cross-modal representation alignment serves as the foundational requirement for achieving cross-modal semantic consistency. The crux of our proposed method entails the collaborative training of an image captioning model(referred to as the ’captioner’) and a pair of contrastive encoders for image-text matching(referred to as the ’concoder’). This synergistic approach yields concurrent enhancements in concoder’s performance, captioner’s proficiency, and cross-modal semantic coherence. We coin the proposed method as ‘ReCap’. To begin, we initialize the concoder through knowledge distillation from a pre-trained model. During the training process, we use the output of the initialized concoder as input to a residual attention network, jointly training it with the captioner to achieve semantic consistency. Subsequently, we iteratively update the concoder during the image-text momentum encoding phase using the residual attention network, creating a closed-loop for semantic consistency resolution. Upon completion of training, the concoder and captioner modules can be used independently to perform tasks related to cross-modal retrieval and cross-modal generation of text and images. In order to substantiate the efficacy of our proposed method, we initially conducted empirical experiments encompassing image-text retrieval and image captioning tasks, employing a widely recognized benchmark dataset, MSCOCO. Subsequently, we assessed the fine-grained cross-modal alignment performance of the concoder through an image classification task on the iNaturalist 2018 dataset. The achieved performance metrics notably surpassed those achieved by several incumbent state-of-the-art models, thus validating the proficiency of our method. Finally, motivated by the practical requirements of handling the nature conservation image data, we performed caption annotation for the iNaturalist 2018 dataset. Subsequently, we trained the ReCap on this annotated data. Experimental results demonstrate that our proposed method can maintain semantic consistency between cross-modal retrieval and image caption generation for species with similar visual features but distinct semantics. This achievement signifies a meaningful exploration in the field of cross-modal semantic consistency representation, holding significant practical value in the domain of biological research.

Teaching, learning, research, and development are all supported in a favorable atmosphere at the University of Lagos (UNILAG). The wetland systems made up of freshwater that are extremely biodiverse makeup about 10% of the total land area. Flooding, deforestation, excessive sedimentation, blockages to streams, abuse, overuse, and invasion of wetlands are some of the recent environmental challenges that the university faced. Urban heat island impacts, contaminants in the air, wetland degradation, social issues including stress, and a detachment from nature are all major concerns. With the green corridor behind the faculties of law and management science serving as a model supported by sustainability as a true foundation for UNILAG's campus landscapes, this article investigates the sustainable restoration of wetlands within the boundaries of the university. The use of qualitative techniques was employed, utilizing the Strengths-Weaknesses-Opportunities-Threats (SWOT) analysis. Additionally, a geospatial mapping of the wetlands and tributaries that connect the Lagos Lagoon was conducted to evaluate the intrinsic ecological goods and services through a series of analytical steps, beginning with an analysis of the land area, current biodiversity, hydrology, and its potential through landscape mapping and analysis. The biophysical setup, landscape features, climatic data analysis, the ecological goods and services derived from the wetlands, and the records of flooding and rainfall are all included in the geospatial evaluation and analysis. The educational institution's site planning for the remediation of its wetlands takes into account the actual evolution of the area's drainage network. Throughout the wetlands, low carbon emissions are generated by off-road bike lanes, trails for walking, and raised hardwood platforms. Combining native plant species and park furniture, the academic landscape atmosphere will be improved in each of the wetlands and aesthetic values. the country's "University of First Choice" and its biophysically restored wetlands will help illuminate the landscape while the green corridors have an innate ability to attract human affinity within the academic community. All of these elements are implemented following an environmentally friendly landscape planning, management, design model, and enforcement process.

Dryland winter wheat in Loess Plateau is facing yield reduction due to shortage of soil moisture and delayed sowing time. Field experiment was conducted at Loess Plateau in Shanxi Province, China from 2012 to 2014, to study the effect of subsoiling and conventional tillage and different sowing dates on the soil water storage and contribution of N accumulation and remobilization to yield of winter wheat. The results showed that subsoiling significantly improved the soil water storage at 0-300 cm depth, improved the number of tillers and pre-anthesis N translocation in various organs of wheat and post-anthesis N accumulation, eventually increased the yield up to 17-36%. Delaying sowing time had reduced the soil water storage at sowing and winter accumulated temperature by about 180˚C. The contribution of N translocation to grain yield was maximum in glume+spike followed by in leaves and minimum by stem+sheath. In addition a close relationship was found between the N accumulation and translocation and the soil moisture in the 20-300 cm. Subsoiling during the fallow period and the medium sowing date was beneficial for improving the soil water storage and increased the N translocation to grain, thereby increasing the yield of wheat, especially in dry year.

Objectives: The purpose of this study is to determine the association between umbilical venous blood flow (UVBF) to placental pulsatility index (PPI) ratio and gestational age (GA) in women undergoing prenatal assessments and adverse pregnancy outcome (APO) screening Methods: Between January and December 2022, sonographic examinations were conducted to assess the fetal umbilical cord insertion site in singleton fetuses, and hemodynamic indices of the umbilical artery, umbilical vein, and uterine artery were computed. Through regression analysis, we derived the optimal regression equation to elucidate the UVBF/PPI ratio parameters based on GA. Results: Among 492 singleton fetuses between 21+0 and 40+6 weeks of gestation in the final study. The average fetal UVBF/PPI ratio was 180.45±119.32. Correlation analysis revealed a positive relationship between the UVBF/PPI ratio and GA(p = .000). Using regression analysis, the best-fit regression equation was the linear function model, which explains the value of UVBF/PPI ratio parameters based on GA. Lower UVBF/PPI ratio revealed a positive relationship in the low birth weight fetuses (p=0.021) and higher preterm delivery rate (p=0.034). Cerebroplacental ratio (CPR) showed a high correlation with the UVBF/PPI ratio (r=0.471, p=0.000). Conclusions: The findings of our analyses revealed that contribute to our understanding of fetal hemodynamics and highlight the potential of UVBF/PPI ratio as a predictive marker for adverse pregnancy outcomes, such as preterm birth, low birth weight, or potential fetal hypoxemia. It might be useful for prenatal counseling and clinical purposes.

DNA methylation, one of the major epigenetic mechanisms, plays critical roles in regulating gene expression, genomic stability and cell lineage commitment. Establishment and maintenance of DNA methylation in mammals is achieved by two groups of DNA methyltransferases: DNMT3A and DNMT3B, which are responsible for installing DNA methylation patterns during gametogenesis and early embryogenesis, and DNMT1, which is essential for propagating DNA methylation patterns during replication. Both groups of DNMTs are multi-modular proteins, containing a large N-terminal regulatory region in addition to the C-terminal methyltransferase domain. Recent structure-function investigations of the individual domains or large fragments of DNMT1 and DNMT3A have revealed the molecular basis for their substrate recognition and specificity, intramolecular domain-domain interactions, as well as their crosstalk with other epigenetic mechanisms. These studies highlight a multifaceted regulation for both DNMT1 and DNMT3A/3B, which is essential for the precise establishment and maintenance of lineage-specific DNA methylation patterns in cells. This review summarizes current understanding of the structure and mechanism of DNMT1- and DNMT3A-mediated DNA methylation, with emphasis on the functional cooperation between the methyltransferase and regulatory domains.

Sharding shows great potential for extending the blockchain. The current challenge facing sharded blockchain technology lies in addressing the extended transaction confirmation times caused by isolated states between shards and unbalanced transaction allocation strategies. These factors contribute to an increase in cross-shard transactions and disproportionate shard workload, ultimately resulting in indefinite confirmation delays for cross-shard transactions. A critical priority for sharded blockchain systems is to conduct a comprehensive qualitative analysis to better understand and mitigate the prolonged transaction confirmation times. We introduce a Product-Form Queue Network (PFQN) model to address the transaction confirmation time problem in sharded blockchains and incorporate a new confirmation queue to more accurately simulate the actual transaction confirmation process in the blockchain. In addition, we provide a detailed quantitative analysis of the relationship between network load, consensus efficiency, and security in sharded blockchains, laying a theoretical foundation for achieving robustness and efficiency in sharded blockchains. This research not only contributes to addressing the scalability issues in sharded blockchains but also offers a new perspective for future research directions.

This work presents a new scheme for autonomous control and obstacle detection of a catamaran unmanned surface vessel. Based on the Newtonian mechanics, hydrodynamics, and maneuvering modelling group modelling principles in the attached coordinate system, a three-degree-of-freedom motion model of the catamaran unmanned surface vessel is constructed. The fuzzy inference method is used to overcome the drawback that the traditional PID control cannot tune the PID parameters online, and the trajectory controller is designed. Meanwhile, 3D LIDAR is used to achieve obstacle detection. The results of the trajectory tracking simulations and experiments verify the accuracy of the model design and the effectiveness of the autonomous control design.

This paper investigates the polarization and heat generation characteristics of batteries under different ambient temperatures and discharge rates by means of using a coupled electric-thermal model. The study found that the largest percentage of polarization is ohmic polarization, followed by concentration polarization and electrochemical polarization. The values of the three types of polarization are generally small and stable under normal-temperature environments and low-discharge rates. However, they increase significantly in low-temperature environments and high-discharge rates and continue to rise during the discharge process. Additionally, ohmic heat generation and polarization generation also increase significantly under these conditions. Reversible entropy heat is less sensitive to ambient temperature but increases significantly with the increase of the discharge rate. Ohmic heat generation and polarization heat generation contribute to the total heat generation of the battery at any ambient temperature, while reversible entropy heat only contributes to the total heat generation of the battery at the end of discharge.

Sinojackia Hu. comprises five to eight Chinese endemic species with high ornamental and medicinal value. However, the generic limits, interspecific relationships and evolutionary history of the genus remain unresolved. In this study, we newly sequenced and assembled three plastomes of S. oblongicarpa and compared them with those of the other congeneric species to explore the taxonomic delimitation of the species and the evolutionary history of the genus. Plastomes structure of Sinojackia species were extremely conserved in terms of number of genes, sequence length and GC content. Codon usage patterns revealed that natural selection may be the main factor shaping codon usage bias. Our phylogenetic tree shows that Sinojackia is monophyletic and can be divided into two clades. Sinojackia oblongicarpa as a distinct species is supported for it is distantly related to S. sarcocarpa. The evolutionary analysis of morphological features indicates that woody mesocarp is an ancestral feature, while mesocarp undeveloped, spongy and fleshy are the later derived. Sinojackia originated in Central-Southeast China during the early Miocene. In this period, it experienced elevated diversification and migrated from the Central-Southeast China to Hunan Province and Sichuan Province with the development of the Asian monsoon and East Asian flora. Sinojackia experienced elevated diversification at intraspecies levels that mainly occurred in the Quaternary. Glacial-interglacial interactions with the monsoon climate may provide favorable expansion conditions for Sinojackia on a small-scale.

In this paper, a semi-empirical model of air waves induced by falling rock is described. The model is composed of a uniform motion phase (velocity close to 0 m·s^-1) and an acceleration movement phase. The uniform motion phase was determined based on experimentally and the acceleration movement phase was derived by theoretical analysis. A series of experiments were performed to verify the semi-empirical model and elucidated the law of the uniform motion phase. The acceleration movement phase accounted for a larger portion with a greater height of the falling rock. Experimental results of different falling heights of the goaf showed close agreement with theoretical analysis values. The semi-empirical model could accurately and conveniently estimate the velocity of air wave induced by falling rock. Thus, the semi-empirical model can provide a reference and basis for estimating the speed of air waves and designing protective measures in mines.

The pandemic SARS-CoV-2 continues to evolve to give rise to variants of concern that can escape vaccine-induced immunity. As such, more effective vaccines are urgently needed. In this study, we evaluated virus-like particle (VLP) as a vaccine platform for SAS-CoV-2. The spike, envelope, and membrane proteins of the SARS-CoV-2 Wuhan strain were expressed by a single recombinant baculovirus BacMam and assembled into VLPs in cell culture. The morphology and size of the SARS-CoV-2 VLP as shown by transmission electron microscopy was found to be similar to the authentic SARS-CoV-2 virus particle. In a mouse trial, two intramuscular immunizations of the VLP BacMam with no adjuvant elicited spike-specific binding antibodies in both sera and bronchoalveolar lavage fluids. Importantly, BacMam VLP -vaccinated mouse sera showed neutralization activity against SARS-CoV-2 spike pseudotyped lentivirus. Our results indicated that the SARS-CoV-2 VLP BacMam stimulated spike-specific immune responses with neutralization activity.

Fuzzy Rule Interpolation (FRI) offers an innovative methodology for inferring outcomes from data points that match no established rules in a sparse fuzzy rule base. Generally, a traditional fuzzy rule-based system suffers from the inability to perform inference while facing an unmatched observation, given a sparse fuzzy rule base that is derived from insufficient data or inadequate human experience and that fails to cover parts of a specific problem domain. Fortunately, starting with a sparse rule base, Fuzzy Rule Interpolation (FRI) can help to formulate interpolated rules specifically in instances where observations fail to activate any existing rule. An interpolated rule gives a result called consequent, which is related to the unmatched observation so that the inference system will not fail to generate an outcome corresponding to the observation as the output. Conventionally, these interpolated rules will be discarded after obtaining outcomes. However, valuable information may be potentially embedded within those discarded rules addressing the limitation regarding the coverage of the original sparse knowledge space. Moreover, without exploiting the potential value of the interpolated rules, the fuzzy inference system based on a sparse rule base will never improve its efficiency and robustness in the long run. Therefore, this underscores the necessity for Dynamic Fuzzy Rule Interpolation (D-FRI), which aims to collate interpolated rules that cover particular knowledge spaces absent in the sparse rule base. Intuitively, those frequently appeared interpolated rules are considered valuable because future observations are more likely to hit the respective problem areas. Promoting selected interpolated rules to the sparse rule base can enhance the overall coverage of the knowledge space and increase the inference efficiency over time. This paper introduces a framework for Dynamic Fuzzy Rule Interpolation that integrates the widely used Transformation-based Fuzzy Rule Interpolation (T-FRI) with an effective form of clustering of interpolated results. Experimental findings validate the effectiveness of this approach.

As the largest energy consumer and carbon emitter, China has made substantial efforts to improve energy efficiency for decrease energy consumption, while the energy rebound effect determines its effectiveness. The embodied energy consumption of construction projects accounted for nearly one-sixth of the total economy's energy consumption in China. This paper is based on the logical relationship among capital input, technological progress, economic growth, and energy consumption, adapting an alternative estimation model to estimate the energy rebound effect for the construction industry in China for the first time. Empirical results in our paper reveal that the energy rebound effect for the construction industry in China is about 59.5% for the period of 1990–2014. The results indicate that the energy rebound effect does exist in China’s construction industry and it presented a fluctuating declining trend. This implies that half of the energy savings by technological progress is achieved. In addition, China’s government should implement proper energy pricing reforms and energy taxes to promote the sustainable development of China’s construction industry.

Rising demand and urbanization have led to the global increase and intensification of livestock production. Intensive production has harmful effects on the environment, public health (due to the emergence of zoonotic diseases), and animal welfare. In order to better understand how livestock production intensifies as countries develop and incomes rise, we examine the relationship between income per capita and intensification of poultry and cattle, using the states of India as a study region. We also replicate this analysis at the district level to test whether the relationship holds at different spatial scales. We identify outlying states and districts to see if there are policies that can keep agriculture production largely extensive, even as economic growth occurs. The results support the relationship of income being positively correlated with the proportion of livestock in intensive conditions. However, there are notable outlier states which have grown wealthy while still maintaining largely extensive production, indicating that there may be some cases where economic growth can occur without intensification.

This study is a two-phase hybrid study on the behavioral activities of undergraduate students during the COVID-19 pandemic lockdown. A questionnaire survey of students during the whole school period and a semistructured interviews with 13 undergraduates of different majors were conducted. First, we found that compared with primary and secondary school students, undergraduates showed many problems with self-time management. Second, the behavior of undergraduates at home may result from multiple factors, such as past experience, professional identity and behavioral habits. When secondary school provided a relatively relaxed learning environment or secondary school teachers placed more emphasis on continuous effort, and when students had a strong sense of the social value of their undergraduate major, students worked harder and achieved more during the pandemic. Otherwise, it was easier for students to slack off and be passive during the pandemic. Altogether, this study deepens our understanding of undergraduates' self-management of free time, and the differences in the values underlying different behaviors and the formation process of various behaviors.

Fish feeding behavior analysis plays a critical role in aquaculture, marine fisheries, and ecological monitoring. At present, the accuracy of current fish feeding behavior analysis is easily affected by the environment, and the hypoxia state in water and high temperature have a huge impact on behavior. In addition, the poor stability, and the speed is affected by the calculation amount of the model, so it cannot be applied to aquaculture ponds. In order to solve the above problems, we propose an improved RepVGG-based method for fish feeding behavior analysis to identify nine behavioral states of fish populations, including hypoxia, hot, and normal states of none, medium, and strong feeding. Firstly, our method adds the identity and residual branches to the block of the VGG network, focusing on the acceleration operation to ensure accuracy. At the same time, the Efficient Channel Attention (ECA) module is added to reduce dimensionality to balance speed and accuracy. To evaluate the effectiveness of the method, it is validated on a constructed fish feeding behavior dataset and compared with a Convolutional Neural Network (CNN) including AlexNet, VGG16, ResNet34, MobileNet V3, and RepVGG. The experimental results show that after 15 epochs of training, the average precision of proposed method reached 97%. Compared with the basic classification algorithm, our method can increase by at least 3% while the inference speed exceeds 85 Frames Per Second (FPS). This study can be integrated into the aquaculture vision system to guide users to plan feeding strategies, and provide new ideas and methods for water quality monitoring.

In this paper, we focus on developing a novel method to extract sea ice cover (i.e., discrimination/classification of sea ice and open water) using Sentinel-1 (S1) cross-polarization (vertical-horizontal, VH or horizontal-vertical, HV) data in extra wide (EW) swath mode based on the machine learning algorithm support vector machine (SVM). The classification basis includes the S1 radar backscatter coefficients and texture features that are calculated from S1 data using the gray level co-occurrence matrix (GLCM). Different from previous methods where appropriate samples are manually selected to train the SVM to classify sea ice and open water, we proposed a method of unsupervised generation of the training samples based on two GLCM texture features, i.e. entropy and homogeneity, that have contrasting characteristics on sea ice and open water. We eliminate the most uncertainty of selecting training samples in machine learning and achieve automatic classification of sea ice and open water by using S1 EW data. The comparison shows good agreement between the SAR-derived sea ice cover using the proposed method and a visual inspection, of which the accuracy reaches approximately 90% - 95% based on a few cases. Besides this, compared with the analyzed sea ice cover data Ice Mapping System (IMS) based on 728 S1 EW images, the accuracy of extracted sea ice cover by using S1 data is more than 80%.

In recent decades, widespread damage to structures due to destructive earthquakes has encouraged researchers to use seismic control systems. One of the most important structures is bridges, which should maintain their service after severe earthquakes. One of the ways to control the bridge is to isolation the deck from the substructure, which results in high displacements at different points in the bridge and the residual displacements within the separator itself, thus requiring repair and replacement of these systems after severe earthquakes. Therefore, the use of new seismic separation systems on bridges has always been important. The purpose of this project is to utilize a new memory-shaped seismic separator system to investigate the seismic performance of v-shaped column bridges , in which case the effect of earthquake orientation and its effects on responses the earthquake will also be assessed. Due to the ever-increasing advances in various intelligent materials, such as shape memory alloys, and their unique capacities, such as back-centering, and high fatigue and corrosion resistance, in this study, these materials have been used as a complementary component along with lead core separators. The shape memory alloy has been used as 4 vertical rods that connect two separating parts to each other and in this research the diameter and location of these rods will be calculated using optimization algorithm in Matlab software.

To overcome the difficulty of separating bastnaesite from fluorite through the flota-tion technique, the present study examined the suitability of sodium alginate (SA) as a depressant in the flotation process. The effect of SA on the flotation separation of bastnaesite and fluorite was evaluated using micro-flotation tests, zeta potential meas-urements, adsorption density measurements, Fourier infrared spectroscopy, and X-ray photoelectron spectroscopy. The micro-flotation results showed that SA exerted a strongly detrimental effect on fluorite flotation, while slightly affecting bastnaesite flotation. The surface chemistry results revealed that the -COO- and HO- functional groups in SA coordinated with Ca2+ on the fluorite surface, which induced hydro-philicity and hindered the adsorption in the subsequent collector. However, the inter-action of SA with the bastnaesite surface was marginal and did not affect the anchor-ing of the collector on the surface of bastnaesite. Based on these results, the present study proposes a possible model for the interaction of SA on the surfaces of the two minerals, laying a foundation for the flotation separation of bastnaesite from fluorite with SA as an environmentally benign depressant.

Globally,coastal regions are vital areas of human activities and, as such, are centres of population growth and urban and economic development. Long-term human development has had a major impact on the ecological environment of coastal zones. Therefore, exploring the distribution and provenance of marine sediment types in coastal areas heavily influenced by human activities can provide scientific evidence and references for the current and future ecological management of these sensitive environments. For this reason, we have conducted an analysis on the sediment grain size, Endmember, organic matter content and geochemical elements in the Lu’erhuan River‒Malan Island‒Sandun Island area in the eastern part of Qinzhou Bay, a region heavily influenced by human activities. Sediment grain size clearly differs throughout the study site and the material provenances and hydrodynamic conditions are also varied, likely due to the local environmental conditions and the significant impact human activities have had on the area. The finest-grained sediment is imported from either inland or coastal areas via rivers and weak tidal currents, the next finest component is input from coastal areas through weak tidal currents, and the moderately coarse component mainly originates from nearby beaches. The two coarsest-grained sediment components are influenced by the combination of human activities, tidal currents and waves and enter the water via erosion. Organic matter provenance resembles that of the sediment components, exhibiting varied characteristics. This is due to the combination of natural and human activities in the bay. The organic matter in the upper reaches of the Lu’erhuan River originates from the river and coastal paddy fields, with obvious terrigenous characteristics; the organic matter in northern Malan Island mainly comes from external sources related to oyster farming; while organic matter in eastern Sandun Island is mainly produced endogenously by marine plankton. Al, Ti, Fe, Mg, K, Ga and other elements indicate that terrestrial sediments are significantly disturbed by human activities. However，Mn reflects the marine distribution of terrestrial sediments from the Lu’erhuan River to Jishuimen. Ca and Sr, indicators of marine sediments, are distributed in the eastern offshore area of Sandun Island, which is connected to the open waters. Due to the influence of human activities, As and Cd are highly enriched in the study area, while Cu is less affected by human activities.

Scaffoldings play a critical role as temporary structures in supporting construction processes. Accidents at construction sites frequently stem from issues related to scaffoldings, including insufficient support caused by deviations from the construction design, insecure rod connections, or absence of cross bracing, which result in uneven loading and potential collapse, leading to casualties. In this study, we introduce a deep-learning-based, augmented reality (AR)-enabled system called scaffolding assembly deficiency detection system (SADDS) to assist field inspectors in identifying deficiencies in scaffolding assemblies. Inspectors have the flexibility to utilize SADDS through various devices, such as video cameras, mobile phones, or AR goggles (i.e., Microsoft HoloLens 2), for automated detection of deficiencies in scaffolding assemblies. The training test yielded satisfactory results, with a mean average precision of 0.89 and individual precision values of 0.96, 0.82, 0.90, and 0.89 for “qualified” frames and frames with the “missing cross-tie rod,” “missing lower-tie rod,” and “missing footboard” deficiencies, respectively. Field tests conducted at two construction sites demonstrated improved system performance compared to that in the training test. However, these field tests also revealed certain limitations of the SADDS system.

Compressed Sensing (CS) MRI has shown great potential in enhancing time efficiency. Deep learning techniques, specifically Generative Adversarial Networks (GANs), have emerged as potent tools for speedy CS-MRI reconstruction. Yet, as the complexity of deep learning recon-struction models increases, this can lead to prolonged reconstruction time and challenges in achieving convergence. In this study we present a novel GAN-based model that delivers superior performance without escalating model complexity. Our generator module, built on the U-net architecture, incorporates dilated residual (DR) networks, thus expanding the network's receptive field without increasing parameters or computational load. At every step of the downsampling path, this revamped generator module includes a DR network, with the dilation rates adjusted according to the depth of the network layer. Moreover, we have introduced a channel attention mechanism (CAM) to distinguish between channels and reduce background noise, thereby fo-cusing on key information. This mechanism adeptly combines global maximum and average pooling approaches to refine channel attention. We conducted comprehensive experiments with the designed model using public domain MRI datasets of the human brain. Ablation studies af-firmed the efficacy of the modified modules within the network. Compared to other relevant models, our proposed model exhibits exceptional performance, achieving not only excellent sta-bility but also outperforming other networks in terms of Peak Signal-to-Noise Ratio (PSNR) and Structural Similarity Index (SSIM). The model presents a promising pathway for enhancing the efficiency and quality of CS-MRI reconstruction.

Remote sensing (RS) as a landscape planning and management tool for socio-cultural diversity and inclusiveness in protected(reserved) areas through monitoring of the land-use changes, settlement/living patterns, predominant trades/socio-economic activities in the urban-rural locations, and the demography in Sub-Saharan Africa (SSA). The eighteen federal governments recognized nature reserves in Nigeria being the giant of Africa because of their green landscapes, rich biodiversity, and human resources. This study aimed to explore the application of remote sensing to assess the extent of land degradation and encroachment in the 18 recognized national parks in Nigeria. A review of the protection of national parks using remote sensing and monitoring the trend of national park invasions which could either be natural or man-made. The study is in line with the United Nations SDG Goal 15: Life on Land- “Protect, restore and promote sustainable use of terrestrial ecosystems, sustainably manage forests, combat desertification, and halt and reverse land degradation and halt biodiversity loss”. Located in the West Africa subregion lying on Latitude: 9° 04' 39.90" N (9.077899) and Longitude: 8° 40' 38.84" E (8.677599), with an estimated population of over 220,000,000 people. This study through an intensive review of various literature adopted a mixed approach for the analysis and assessment of the geospatial data, the updated aerial photographs obtained through the Landsat imageries (Google Earth Pro, 2023), and the use of GIS for Geospatial analysis which enables the collection and analysis of spatial and geographic data gathering land use/land covers (LULC) maps, soil type, and elevation maps. While exploring the geophysical ecology and biodiversity conservation of some selected national parks in Nigeria, while also providing cost-effective alternatives for biodiversity monitoring and conservation strategy development. A review of national implementation strategies on biodiversity conservation with the deployment of remote sensing technologies, it is now feasible to obtain large details of the surface of the planet without conducting arduous field activities with the assistance of the availability of multi-date, multi-resolution, multi-sensor aerial information to help prevent for encroachment, loss, and degradation of the natural landscapes.

Survivin was initially identified as a member of the inhibitor apoptosis (IAP) protein family and has been shown to play a critical role in regulation of both apoptosis and mitosis. Survivin has emerged as an attractive target for cancer therapy because its overexpression has been found in most human cancers and is frequently associated with chemotherapy resistance, recurrence, and poor survival rate in cancer patients. In this review, we discuss our current understanding of how survivin mediates various aspects of malignant transformation and drug resistance, as well as efforts that have been made to develop therapeutics targeting survivin for the treatment of cancer.

In recent years discrete element method (DEM) has gradually been applied to the traditional fluidization simulation of fine particles in micro fluidized bed (MFB). The application of DEM in simulating fast fluidization of fine particles in MFB has not yet received attention. This article presents a drag model that relies on the surrounding environment of particles, namely particle circumstance-dependent drag modle or PCDD model. Fast fluidization in MFB of fine particles is simulated using DEM based on the PCDD model. It is found that the gas-solid two-phase flow in MFB meets the common law of fast fluidization in circulating fluidized bed (CFB) to a certain extent, and also presents a special law that is significantly different from that in CFB. Simulations indicate that the local structure in MFB exhibits particle aggregation which is a natural property of fast fluidized, forming a structure where continuous dilute phase and dispersed concentrated phase coexist. The formation and fragmentation of particle clusters in different local regions of the bed have time synchronization. There exists strong effect of solid back-mixing in MFB, leading to relatively low outlet solid flux. The gas back-mixing effect is, however, not so distinct. The axial porosity shows a monotonically increasing distribution with the bed height, but does not strictly follow the single exponential distribution. The solid volume fraction at the bottom of the bed is significantly lower than the correlated value in CFB. The axial heterogeneous distribution of the cross-sectional average porosity in the lower half of the bed is also weakened. The radial porosity shows a distribution pattern of higher in the central region and lower in the sidewall region. Compared with the correlation results in CFB, the porosity near the central region in MFB is relatively low, while the porosity near the sidewall region is relatively high. The geometric size of the container, especially the radial size, is much smaller than that of a CFB. The relative area of contact between the MFB wall and particles is larger, and the wall friction factor becomes more significant. This may be the main reason for the time synchronization of particle agglomeration, severe particle back-mixing, low outlet solid flux, monotonically increasing axial porosity and weak core-annular structure of radial porosity.

Aiming at the defects of low precision and time cumulative error, an external wireless signal weighted centroid localization algorithm aided inertial positioning method is designed in this paper. According to the signal strength of each anchor node received at the test point, the distance between the anchor node and the anchor node is obtained by using the attenuation model of the wireless signal. Three anchor nodes are used to measure the distance between the anchor node and the measured point. We can obtain the area to be measured according to the actual situation, the position of the measured point is obtained by the weighted centroid localization algorithm and a combined model of wireless signal aided inertial navigation system is established. The simulation results show that the method can greatly improve the positioning accuracy and restrain the divergence of the longitude error and latitude error.

Sensory descriptive analysis was used to evaluate the aged Feng-flavored baijiu. The results indicated that there are notable differences in the samples of different ages. The samples with shorter storage times and fresh distilled Baijiu present bran flavor, and fresh green flavor. with the increase of storage time, the fragrance of honey, sweetness, flowers, and aging gradually increases. The samples of Feng-flavored baijiu were dected by Headspace solid-phase microextraction (HS-SPME) combined with comprehensive two-dimensional gas chromatography time-of-flight mass spectrometry (GC×GC–TOFMS) , in total, 496 sustances were identified in all samples, mainly containing 14 types of substances, such as esters, aldehydes etc., of which 42 substances were found in Feng-flavored baijiu for the first time. Chemometrics was used to analyze the key differential compounds. 143 differential compounds closely related to aging were preliminarily screened, and principal component analysis revealed that these samples were separated by year. 65 differential compounds were selected out by partial least squares discriminant analysis(PLS-DA). Furthermore, 43 key differential compounds were selected from the aged Feng-flavored baijiu combined with variable importance in projection and Pearson correlation coefficients. Partial least squares regression (PLSR) was used to research the correlation of sensory properties and key differential compounds, and the results indicated that most compounds were closely related to the aged Baijiu . This study afford theoretical basis and reference for flavor research of Feng-flavored baijiu.

To date, viral RNA detection is almost the only way to confirm SARS-CoV-2infectionin practice.However, variousreasons can cause low sensitivity for RNA detection, and thisposes aserious challenge to disease control. We tested the performance of detecting total antibody(Ab) and IgM levels in serum by the methods of chemiluminescence, enzyme-linked immunosorbent assay (ELISA), and colloidal golddetection. The datashowed that the sensitivity and specificity for detecting total Ab and IgM levels were high by all three methods, and the sensitivity was higher for detecting total Ab than for detecting IgM. Evidence from studieshas shown thatviral RNA testingcombinedwith serological testing could increase the diagnostic sensitivity while maintaining a high specificity. Specific serology testsfor SARS-CoV-2 havegreat value for clinical practice and public health.

In the fifth generation communication system, millimeter wave (mmWave) networks will coexist with traditional micro wave (μWave) networks, which allows for higher data transmission rate and better user experience. In this paper, we give a comprehensive framework of mathematical models and analytical methods for multi-tier mmWave and μWave hybrid caching networks based on stochastic geometry. We propose an association strategy by assuming average biased-received power association and Rayleigh fading. Accordingly, by using a D-ball approximating blockage model of mmWave networks, expressions of the cell association probability and the coverage probability of the hybrid networks are derived. Also, we use the average successful delivery probability as the performance metric to analyze the existing caching placement strategies. Simulation results validate the accuracy of our analytical conclusions.

The advancement in science and technology has led to luffa sponge (LS) being widely used as a natural material in industrial application as its polyporous structure and light texture. In order to enhance the utility of LS fibers as the reinforcement of lightweight composite materials, this study investigate its water absorption, mechanical properties, anatomical characteristic and thermal performance. Hence, moisture regain, tensile properties of LS fiber bundles were measured in accordance with standards and the structural characteristics were investigated via microscopic observation. Scanning electron microscopy (SEM) was used to observe the surface morphology and fracture surface of fiber bundles. Test results shows that the special structure where the phloem tissues degenerate to cavities had a significant influence on the mechanical properties of LS fiber bundles. Additionally, the transverse sectional area occupied by fibers in a fiber bundle (SF), wall thickness and ratio of wall to lumen of fiber cell, and crystallinity of cellulose had an impact on the mechanical properties of LS fiber bundles. Furthermore, the fiber bundles density of LS varies range of 385.46-468.70 kg/m³, much less than that of jute (1360.40 kg/m³) and Arenga engleri (950.20 kg/m³) while LS fiber bundles has superior specific modulus.

As an emerging discipline, Design Morphology, with the advantage of "Form Study", has been integrated with many disciplines, and gradually formed its collaborative innovation paradigm. The inclusion of "Ecology" into Design Morphology is expected to promote the research of Design Morphology with the help of the systematic thinking and methods of ecology. The ecosystem of Design Morphology includes the natural ecosystem and the quasi-ecosystem closely related to human beings, and also put forward the concept of "Form Community" for the first time in the design field. In fact, this is exactly the research scope of Design Morphology. Advocating the ecological view of Design Morphology, can not only help to design researchers improve their values and world view, with new thinking and method to engage in "Form Study", but also contribute to the theoretical construction and thinking expansion of Design Morphology, and play a positive role in promoting interdisciplinary collaborative innovation led by Design Morphology. In addition, it can be used to evaluate the overall research and future development trend of Design Morphology, and provide the new research ideas and approaches for the development of design.

This study uses machine learning to predict the convergence results of the Duffing equation with and without damping. The Duffing equation represents a nonlinear second-order differential equation with interesting behavior in undamped free vibration and forced vibration with damping. Convergence alternates randomly between 1 and -1 in undamped free vibration, depending on initial conditions. For forced vibration with damping, multiple factors influence vibration patterns. We utilize the fourth-order Runge-Kutta method to collect convergence results for both conditions. Machine learning techniques, specifically the long short term memory (LSTM) and LSTM-Neural Network (LSTM-NN) method, are employed to predict these convergence values. The LSTM-NN model is a hybrid approach that combines the LSTM method with the addition of hidden layers of neurons. Both the LSTM and LSTM-NN models are thoroughly explored and analyzed in this research. The research process involves three stages: data preprocessing, training, and verification. The results show that the LSTM-NN model becomes more adept at predicting binary datasets, boasting an impressive accuracy of up to 98%. However, when it comes to predicting multiple solutions, the traditional LSTM method outperforms the LSTM-NN approach.

Current physiology attributes the mechanism of membrane potential generation to transmembrane ion transport, but ion adsorption could just as well play this fundamental role. The evidence shows that the ion adsorption mechanism accurately reproduces the experimentally measured membrane potential. The Goldman-Hodgkin-Katz equation (GHK eq.) and the Nernst equation (Nernst eq.) are the typical mathematical formulas representing the membrane potential in current physiology. However, the authors were able to show that the potential formulas by ion adsorption mechanism give identical results to GHK eq. and Nernst. eq. Our experimental and theoretical analyses suggest that there is a special relationship between the membrane potential and the membrane surface charge density, and this unique equation inevitably leads to the establishment of a GHK eq and/or a Nernst eq. The authors found that the unique equation is the foundation of thermodynamics “Boltzmann distribution”. Thus, the GHK eq. and the Nernst eq. are simply the natural consequence of thermodynamics from the view of the ion adsorption mechanism.

The part transportation efficiency is a main factor of aircraft sortie generation rate. Part transportation is used to transport spare part from base to carrier. Transportation strategy depends on both demand on carrier and inventory in transportation base. The transportation time and stochastic demand will induce fluctuations of cost and inventory. Thus, a Takagi-Sugeno fuzzy system of dynamic part transportation is established considering transportation time and stochastic demand. And a novel Takagi-Sugeno fuzzy robust control is designed for dynamic part transportation, which will keep transportation cost and part inventory stable. First of all, a fuzzy model with stochastic demand and transportation time is proposed. Then, a novel robust control with cross rule groups is conducted according to production and transportation strategy, which will reduce fluctuations induced by strategies switch. Moreover, robust stability is guaranteed and part can be supplied in time under a low cost. Finally, simulation illustrates usefulness and quickness of the novel Takagi-Sugeno fuzzy robust control. Besides, the proposed method will be useful in other transportation electrification systems with delay time and uncertainty.

MicroRNAs (miRNA) exert regulatory actions via base-pairing with their binding sites on target mRNAs. Cooperative-binding, i.e., synergism, among binding sites on a mRNA is biochemically well-characterized. We studied whether this synergism is reflected in global relationship between miRNA-mediated regulatory activity and miRNA-binding-site count on the target mRNAs, i.e., leading to a non-linear relationship between the two. Recently, using our own and public datasets, we have enquired into miRNA regulatory actions: first, we analyzed the power-law distribution pattern of miRNA binding sites; second, strikingly, mRNAs for core miRNA regulatory apparatus proteins have extra-ordinarily high binding site counts, forming self-feedback-control loops; third, we revealed that tumor suppressor mRNAs generally have more sites than oncogene mRNAs; and fourth, we characterized enrichment of miRNA target mRNAs in translationally less-active polysomes relative to more-active polysomes. In these four studies, obvious correlation was observed qualitatively between the extent to which a mRNA is miRNA-regulated and its binding sites count. This paper summarizes the used datasets. We also re-analyzed the correlation by comparative linear and non-linear regression analyses. The results support a non-linear, instead of linear, relationship between the two parameters, conceivably a transcriptome-level reflection of cooperative-binding/synergism among miRNA binding sites on a target mRNA.

Cloud-induced atmospheric extinction and occlusion have a major effect on the effectiveness and quality of telescope observations. Real-time cloud cover distribution and long-term statistical data are essential for astronomical siting and telescope operations. At ground-based astronomical telescope sites, cloud cover distribution is currently analyzed using manual observation methods. However, the main disadvantages of manual observation methods are human subjective, heavy workloads and poor real-time performance. Therefore, a real-time automatic cloud images classification method is desperately needed. This paper presents a new cloud identification method, which is named PSO+XGBoost model by combining eXtreme Gradient Boosting (XGBoost) and Particle Swarm Optimization (PSO). The entire cloud image is divided into 37 sub-regions in order to more precisely identify the distribution of the clouds. 19 features are then extracted, including the sky background, star density, lighting conditions, and subregion grayscale values. The experimental results have shown that the overall classification accuracy of 96.91% and our model is able to outperform several state-of-the-art baseline methods. Our approach achieves high accuracy in comparison with the manual observation methods. Moreover, this method meets telescope real-time scheduling requirements.

Strong-aroma Baijiu is a traditional Chinese spirit distilled from grains that undergo solid-state fermentation. At the end of each fermentation cycle, a significant quantity of Huangshui accumulates at the bottom of the fermentation pit, constituting one of the primary by-products in the brewing process of strong-flavor liquor. In this report, the chemical component analysis of Huangshui obtained from a strong-flavor liquor factory revealed a diverse array of organic acids, alcohols, esters, starch, reducing sugars, amino acids, and other compounds present in Huangshui. Additionally, two specialized solid-state fermentation models were developed to investigate the formation process of Huangshui. Our findings demonstrate a positive correlation between the yield of Huangshui and the initial moisture content of fermented grains. It is concluded that Huangshui is the percolate produced during the solid-state brewing process of strong-flavor liquor, with its water content originating from the initial moisture of fermented grains.

This study derives space travel pricing by Walrasian Equilibrium, which is logical reasoning from the general relativity theory (GRT), the accounting equation, and economic supply and demand functions. The Cobb-Douglas functions embed the endogenous space factor as new capital to form the space travel firm's production function, which is also transformed into the consumer's utility function. Thus, the market equilibrium occurs at the equivalence of supply and demand functions, like the GRT presents the equivalence between the spatial geometric tensor and the energy-momentum tensor, which explains the principles of gravity and the motion of space matter in the spacetime framework. The mathematical axiomatic set theory of the accounting equation explains the equity premium effect that causes a short-term accounting equation inequality, then reaches the equivalence by suppliers' incremental equity through the closing accounts process of the accounting cycle. On the demand side, the consumption of space travel can be assumed as a value at risk (VaR) investment to attain the specific spacetime curvature in an expected orbit. Spacetime market equilibrium is then achieved to construct the space travel pricing model. The methodology of econophysics and analogy method was applied to infer the space travel pricing by the model of profit maximization, single-minded, and envy-free pricing in unit-demand markets. A case study with simulation was conducted for empirical verification of the math models and algorithm. Results show that space travel pricing remains the principle of market equilibrium but needs to be extended to the spacetime tensor of GRT.

This work aims at improving surface integrity and LCF life of machined Inconel 718. The correlation between the LCF life of Inconel 718 and various states of machined surface integrity is explored. In this paper, the surface integrity of Inconel 718 specimens is enhanced by low plasticity burnishing (LPB). The LCF life with different surface integrity specimens is predicted by micro-macro finite element method (FEM). Firstly, the LCF specimens with different surface integrity are machined by turning (turned specimen), polishing (matrix specimen) and LPB process (LPBed specimen). Secondly, the LCF experiment is carried out to reveal the effect of surface integrity on LCF life. Finally, the LCF micro-macro FEM model is proposed to predict the LCF of machined Inconel 718 specimens. The representative volume element (RVE) model is established based on the measured surface integrity and microstructure of Inconel 718 specimens. The effect of surface integrity on LCF life is transformed to equivalent load. The micro-macro FEM model combined with Tanaka-Mura dislocation crack initiation theory and extended finite element method (XFEM) is applied to predict the LCF life the machined specimens. The study results show that the LCF life of LPBed specimens can be improved by 90.5% and 36.1% compared with that of turned specimens and polished matrix specimens, respectively. The errors between FEM prediction results and experimental results are 13.1%, 9.2% and 12.2%, respectively. The proposed micro-macro FEM model could be utilized to predict the LCF life of Inconel 718 with different surface integrity, and further to apply the LCF life prediction in industry.

The phycobilisome (PBS) is the major light-harvesting apparatus in cyanobacteria and red algae, a large multi-subunit protein complex of several megadaltons that is found on the stromal side of thylakoid membranes in orderly arrays. Chromophore lyases catalyse the thioether bond between apoproteins and phycobilins of PBSs. Depending on the species, composition, spatial assembly and, especially, the functional tuning of different phycobiliproteins mediated by linker proteins, PBSs can absorb light between 450 and 650 nm, making them efficient and versatile light-harvesting systems. However, basic research and technological innovations are needed, not only to understand their role in photosynthesis but also to realise the potential applications of PBSs. Synthetic biology provides an innovative approach to expand our understanding of the distinctive properties that make the PBS such an efficient light-harvesting system and to explore its heterologous synthesis, photosynthetic functions and potential medical applications. Focusing on these topics, this review describes the essential components needed for PBS assembly, the functional basis of PBS photosynthesis and the applications of phycobiliproteins. Moreover, key technical challenges for heterologous biosynthesis of phycobiliproteins in chassis cells are discussed.

Previously, pseudomyogenic hemangioendothelioma (PMHE) is regarded as epithelioid sarcoma-like hemangioendothelioma due to significant histologic overlapping and diffuse cytokeratin expression since the first description in 1992. After considerable controversy and long-term debating, it is currently defined as a distinct intermediate malignant, rarely metastasizing neoplasm with vascular/endothelial differentiation in nature. PMHE is characterized by young age (typically < 40 years old) and extremity location (approximately ~80%) with t(7:19) SERPINE1-FOSB fusion as the most common molecular alteration. Here we reported a 59-year-old male presenting with multifocal lesions, including right temporalis muscle, right frontoparietal calvarium, right pterygoid muscles, and right mandibular condyle. Histologic examination of the lesion from right temporal mass revealed a multinodular biphasic lesion composed of sheets and fascicles of elongated spindle cells, and epithelioid small round to ovoid cells infiltrating into the adjacent skeletal muscle admixed with abundant neutrophilic infiltration. No rhabdomyoblast-like cells, prominent nuclear pleomorphism and mitosis were identified. IHC staining showed that the tumor cells were diffusely and strongly positive for FOSB, pan-cytokerain (AE1/AE3), CD31, ERG, and molecular testing further demonstrated a t(9:19) EGFL7::FOSB fusion mRNA. This constellation of morphological, IHC and molecular findings was consistent with the diagnosis of PMHE. This is the first reported case of multiple PMHEs with EGFL7::FOSB fusion in a patient aged more than 50 years old in the head and neck area. Since the vast majority of the differential diagnoses of PMHE are high-grade malignancies with aggressive clinical behavior and PMHE is rarely reported in the head and neck region, awareness of this tumor will avoid misdiagnosis and over-treatments of this entity.

Early-season crop-type data are required for a variety of agricultural monitoring and decision-making applications. The early season in this study referred to the prophase and middle of a growth season. Early-season detection of crop types remains challenging because of limited discriminative features, especially for landscapes that are characterized by complex cropping patterns. In fact, different remote-sensing satellites can increase the frequency of data acquisition, which can provide more information in the early season. Moreover, optical and radar sensors have different degrees of sensitivity to crop parameters. Therefore, the integration and application of two types of multitemporal data are of great significance to improve the accuracy and timeliness of crop type detection.In deep learning (DL), convolutional neural network (CNN) and recurrent neural network (RNN) models have great potential for temporal feature extraction. Compared with RNNs, CNNs usually have fewer parameters and are more conducive to determining early-season detection dates of different crop types, which requires a lot of training because of the need to model on different dates. Nevertheless, revisit dates and temporal intervals of different satellites are usually different, resulting in different data acquisition time series; these data cannot be directly used as input for the same convolutional layer. To address this challenge, a Dual-1DCNN was bulit based on the CNN model in this study. Moreover, an incremental training method was used to attain the network on each data acquisition date and obtained the best detection date for each crop type in the early season. A case study for Hengshui City in China was conducted using time series of Sentinel-1A (S1A) and Sentinel-2 (S2). To verify this method, classical methods support vector machine (SVM) and random forest (RF) were implemented. The results demonstrated the following: (1) the Dual-1DCNN extracted discriminative features from S1A and S2 time series at the early season by producing the highest overall accuracy (OA: 87.23%); (2) for summer maize, cotton, and common yam rhizome, the Dual-1DCNN achieved F1 values of 92.39%, 87.71%, and 84.38%, respectively, at the early season (moreover, the early seasons were almost 40, 70, and 80 days before the end of the growth seasons, respectively). These findings suggested that the Dual-1DCNN is promising for the accurate and timely detection of crop types.

As the most commonly used hydrogel material in contact lenses, the amount of water in a lens affects its optical properties and comfort for the wearer. Therefore, an important challenge is to determine the safety and efficacy of contact lenses by accurately and non-destructively measuring the water content in real time. In this study, we demonstrate the accurate detection of water content in hydrogel contact lenses using a high-precision ATR format in a portable terahertz time-domain spectroscopy system. The technique can resolve small variations in the dielectric constant in solution, which is difficult to achieve with traditional transmission and reflection measurement modes. Information is obtained from the interaction between the sample and the swift waves propagating along the prism surface. The swift waves can excite longitudinal modes that are not directly accessible by conventional techniques. It is worth noting that the reference wave can be measured by removing the sample without disturbing the optical path. We also enhance the plasma effect at the interface with the hydrogel by using PVDF dielectric films of different polarities. We observed that the water content and refractive index changes in the ATR mode show different response patterns for nonpoled PVDF and poled PVDF membranes. This suggests that reflection and relative phase can be accurately evaluated in the THz-ATR technique, resulting in an accurate method for determining complex dielectric constants in the reflection geometry. This will allow accurate measurement of both surface and in vivo water content in hydrogels in the future and is a potential technical route for application in bioaqueous tissue measurements.

Revealing the multidimensional value of cultivated land resources, improving calculation methods, and exploring their spatial distribution characteristics and influencing factors are crucial for the enhancement of natural resource accounting system and the protection of cultivated land resources. This study take Guangxi, China as an example and construct a comprehensive multidimensional value evaluation system for cultivated land resources at the county scale. The income capitalization method, substitution market method, and value equivalent correction method were applied to calculate the economic, social, and ecological values of cultivated land resources in 111 counties. Furthermore, spatial autocorrelation analysis was employed to study their distribution characteristics and influencing factors. The results show that: (1) The total value of cultivated land resources in Guangxi reach 19,729.2 billion yuan, and the average cultivated land value is 5.3511 million yuan/hm2, of which the ratio of economic, social and ecological values is about 6:1:2; (2) The value of cultivated land has a certain distribution pattern in the global space, and the average economic and social value show the spatial distribution patterns of "low in the west and high in the east" and "low in the northwest and high in the southeast" respectively."(3) There is a significant spatial clustering effect of all values of cultivated land resources in local space, with "high-high" and "low-low" clustering. (4) Economic development level is significantly negatively correlated with the ecological value of cultivated land, while has a significant positive correlation with social value; (5) Natural conditions, economic development and agricultural development approaches are the key factors affecting the value of cultivated land resources.

With the development of engineering technology, engineering has higher requirements for the accuracy and the scale of simulation calculation. The computational efficiency of traditional se-rial program can not meet the requirements of engineering。Therefore, reducing the calcula-tion time of temperature control simulation program has important engineering significance for real-time simulation of temperature field and stress field, and then adopting more reasona-ble temperature control and crack prevention measures. GPU parallel computing is introduced into the temperature control simulation program of massive concrete to solve this problem and the optimization is carried out. Considering factors such as GPU clock rate, number of cores, parallel overhead and Parallel Region, The improved GPU parallel algorithm analysis indicator formula is proposed. It makes up for the shortcomings of traditional formula that focus only on time. According to this formula, when there are enough threads, the parallel effect is limited by the size of the parallel domain, and when the parallel domain is large enough, the efficiency is limited by the parallel overhead and the clock rate. This paper studies the optimal Kernel execu-tion configuration. Shared Memory is utilized to improve memory access efficiency by 155%. After solving the problem of bank conflicts, an accelerate rate of 437.5x was realized in the sub-routine of the matrix transpose of the solver. The asynchronous parallel of data access and logi-cal operation is realized on GPU by using CUDA Stream , which can overlap part of the data access time. On the basis of GPU parallelism, asynchronous parallelism can double the compu-ting efficiency. Compared with the serial program, the accelerate rate of inner product matrix multiplication of the GPU asynchronous parallel program is 61.42x. This study further proposed a theoretical formula of data access overlap rate to guide the selection of the number of CUDA streams to achieve the optimal computing conditions. The GPU parallel program compiled and optimized by CUDA Fortran platform can effectively improve the computational efficiency of the simulation program for concrete temperature control, and better serve for engineering computing.

We have repeated the experiment performed recently by Krasznahorkay et al., (Phys. Rev. Lett. 116, 042501 (2016)), which may indicate a new particle called X17 in the literature. In order to get a reliable, and independent result, we used a different type of electron-positron pair spectrometer which have a more simple acceptance/efficiency as a function of the correlation angle, but the other conditions of the experiment were very similar to the published ones. We could confirm the presence of the anomaly measured at the Ex=18.15 MeV resonance, and also confirm their absence at the Ex=17.6 MeV resonance, and at Ep= 800 keV off resonance energies.

The decline in Pinus sylvestris var. mongolica in the introduction area has had a high profile in recent years. For the ecological restoration, management and silvicultural design of Mongolian pines in the introduction area, it is necessary to conduct a comprehensive and in-depth study on the ecological adaptation mechanism of Mongolian pines in provenances. The ecological process of water and nutrient accumulation as well as the influence of environmental factors on the photosynthetic physiology are the key to revealing the ecological adaptation mechanism of Mongolian pines. According to the differences of climate in the distribution area of Mongolian pines, sampling sites were set up, the effects of environmental factors on leaf δ13C and the relationship between leaf δ13C and nutrient content were analyzed. The results showed that leaf δ13C values were ranging from - 29.7 ‰ to - 23.76 ‰. The ecological stoichiometry, including LC (522.81 mg·g-1), LN (16.04 mg·g-1), LP (1.19 mg·g-1) and L-N:P (13.56), indicated that leaf photosynthesis and water use efficiency is greatly affected by environmental conditions, Mongolian pines had strong ability of carbon fixation, and its growth was obviously restricted by nitrogen. Although there was no significant correlation between δ13C with stoichiometric parameters in leaf, photosynthesis was the key link in the process of carbon fixation. It also showed that Pinus sylvestris var. mongolica was a stomatal limited plant. Leaf δ13C had significant correlation with climatic factors. VPD is the dynamic factor affecting the photosynthetic physiological process in leaves. Air and soil moisture are the dominate factors affecting the leaf stomatal conductance and determines leaf δ13C value, while other factors indirectly affect leaf δ13C by its impact on relative humidity or soil water content. Soil phosphorus content affected by clay is a key factor affecting soil water availability and soil nutrient cycling. Photosynthetic process in leaf is the dynamic process affecting the nutrient accumulation.

Horizontal transfer of transposons (HTT) is an important source of genomic evolution in eukaryotes. The HTT dynamics is well characterized in eukaryotes including insects however, but there is a huge gap of knowledge about HTT regarding many eukaryotes’ species. In this study we analyzed the events of the HTT between Rhus gall aphids (Hemiptera) and other insects. We analyzed the Mariner-like transposable elements (MLEs) belongs to Rhus gall aphids for the possible HT events. The MLEs have patchy distribution and have high similarity over the entire length of element with insects MLEs from different orders. We selected representative sequences from the Rhus gall MLEs and identified five events of HT between MLEs of Rhus gall aphids and other insects from five different orders. We also found multiple HTT events among the MLEs of insects from the five orders which demonstrate that these Mariner elements have been involved in recurrent HT between these six order of insects. Our current study closed the knowledge gap of HTT and reported the events between Rhus gall aphids and other insects for the first time. We believe that this study about HTT events will help to understand the evolution and spread of transposable elements in the genomes of Rhus gall aphids.

For massive multiple-input multiple-output (MIMO) communications, the minimum mean square error (MMSE) scheme provides close to optimal recognition but involves inverting the high-dimensional matrix. A Gauss-Seidel (GS) detector based on conjugate gradient and Jacobi iteration (CJ) joint processing is introduced to address this problem. Firstly, the signal is initialized with the best of the three initialization regimes for faster algorithm convergence. Secondly, the signal is processed together with CJ. Finally, the pre-processed result is transferred to the GS detector. The simulation results indicate that the proposed iterative algorithm has a lower BER performance than the GS and improved iterative scheme based on GS in channels with different correlation levels.

The 11 system in iron-based superconducting family has become one of the most extensively studied materials in the research of high-temperature superconductivity due to their simple structure and rich physical properties. However, the research on 11 iron-based superconductors faces numerous obstacles, mainly stemming from the challenges associated with producing high-quality single crystals. Since the discovery of FeSe superconductivity in 2008, researchers have made significant progress in crystal growth, overcoming the hurdles that initially impeded their studies. Consequently, they have successfully established the complete phase diagrams of 11 iron-based superconductors, including FeSe1-xTex, FeSe1-xSx and FeTe1-xSx. In this paper, we aim to provide a comprehensive summary of the preparation methods employed for 11 iron-based single crystals over the past decade. Specifically, we will focus on hydrothermal, chemical vapor transport (CVT), self-flux, and annealing methods. Additionally, we will discuss the quality, size, and superconductivity properties exhibited by single crystals obtained through different preparation methods. By exploring these aspects, we can gain a better understanding of the advantages and limitations associated with each technique.

We introduce a novel hybrid Transformer-CNN architecture for robotic grasp detection, designed to enhance the accuracy of grasping unknown objects. Our proposed architecture has two key designs. Firstly, we develop a hierarchical transformer as the encoder, incorporating the external attention to effectively capture the correlation features across the data. Secondly, the decoder is constructed with cross-layer connections to efficiently fuse multi-scale features. Channel attention is introduced in the decoder to model the correlation between channels and to adaptively recalibrate the channel correlation feature response, thereby increasing the weight of the effective channels. Our method is evaluated on the Cornell and Jacquard public datasets, achieving an image-wise detection accuracy of 98.3% and 95.8% on each dataset, respectively. Additionally, we achieve object-wise detection accuracy of 96.9% and 92.4% on the same datasets. A physical experiment is also performed using the Elite 6Dof robot, with a grasping accuracy rate of 93.3%, demonstrating the proposed method's ability to grasp unknown objects in real-world scenarios. The results of this study show that our proposed method outperforms other state-of-the-art methods.

In the field of vision-based robot grasping, effectively leveraging RGB and depth information to accurately determine the position and pose of a target is a critical issue. To address this challenge, we propose a tri-stream cross-modal fusion architecture for 2-DoF visual grasp detection. This architecture facilitates the interaction of RGB and depth bilateral information and is designed to efficiently aggregate multiscale information. Our novel modal interaction module (MIM) with spatial-wise cross-attention algorithm adaptively captures cross-modal feature information. Meanwhile, the channel interaction modules (CIM) further enhance the aggregation of different modal streams. In addition, we efficiently aggregate global multiscale information through a hierarchical structure with skipping connections. To evaluate the performance of our proposed method, we conduct validation experiments on standard public datasets and real robot grasping experiments. We achieve the image-wise detection accuracy of 99.4% and 96.7% on Cornell and Jacquard datasets respectively. The object-wise detection accuracy reaches 97.8% and 94.6% on the same datasets. Furthermore, physical experiments using the 6-DoF Elite robot demonstrate a success rate of 94.5%. These experiments highlight the superior accuracy of our proposed method.

Acemetacin (ACM) is a new non-steroidal anti-inflammatory drug with anti-inflammatory, analgesic, and antipyretic effects. However, the poor water solubility and gastrointestinal side effects limit its use. Recently, the co-amorphous (CAM) strategy has attracted great interest to improve solubility for poorly water-soluble drugs, and basic amino acids have the potential to protect the gastrointestinal tract. In order to develop highly efficient and low toxic ACM formulation, we propose to prepare ACM CAM, with basic amino acids (lysine, arginine and histidine) as co-formers, using a cryo-milling method. The solid-state behaviors of the ACM CAMs were characterized by polarizing light microscopy, differential scanning calorimetry and powder X-ray diffraction. Fourier transform infrared spectroscopy and molecular docking were carried out to understand the formation mechanism. Moreover, the gastro-protective effects of ACM CAMs were evaluated in a rat gastric ulcer model. The results demonstrated CAMs improved the dissolution rates of ACM compared with the neat amorphous counterpart. Furthermore, ACM CAMs are significantly effective in mitigating the ACM-induced gastric ulcer in rats, and the ulcer inhibition rates were almost 90%. More importantly, this study provided a useful method for mitigating drug-induced gastrointestinal damage and broadened the applications of drug-amino acid CAMs.

HybridAC/DC microgrids(HMG) are emerging as an attracting method for integrating the AC/DC distributed energy resources(DERs) with the features of high-performance and low-cost. In the isolated hybrid AC/DC microgrid (IHMG), the key problem is how to balance the power variation and regulate the voltage and frequency. Various energy storage systems (ESS)and interlinking converter (IC) technologies are viable for this application. The present study proposes a novel unified power flow model to evaluate and compare the abilities of the ESS with different connection topologies and ICs with different control approaches to maintain the voltage and frequency stability of the IHMG. In order to investigate the performance of the proposed scheme, five operation modes of the IHMG are defined and explained. The classification is based on the connection topologies and control modes of the ESS/IC in the IHMG. Then, a set of generic PF equations are derived. Moreover, three binary matrices are applied in the construction of the unified power equations. These matrices are used for describing the running state of the IHMG. Finally, in order to verify the proposed scheme, it is applied to several case studies of the IHMG. The operation characteristics of multi-DC subgrids IHMG in different modes, particularly when an external disturbance occurs, are investigated.

In the wake of the rapid deployment of Small Modular Reactors (SMRs), this study aims to enhance the efficiency, reliability, and safety of SMR operations through a deeper understanding of human factors in their interaction within digital control room systems. Recognizing the pivotal role of human understanding in this new era of nuclear power, we employed electroencephalogram (EEG)-based monitoring to provide an unparalleled real-time view into operators' cognitive states. By interfacing detailed human models, informed by EEG metrics, with specific operational tasks, we recreate potential operational scenarios using an SMR simulator and capture intricate human responses therein. Our results elucidated the intricate relationship between EEG-derived data and human performance shaping factors, indicating a marked correlation between certain EEG patterns and operational efficiencies. Conclusively, these findings underscore the potential of EEG monitoring not only as a diagnostic tool but as an instrumental aid in the design and operation of future SMR digital control rooms. The insights derived offer a roadmap for the development of practical strategies, ensuring more effective and safer SMR operations.