In the future, the pursuit of high-quality economic development and a focus on ecological environmental protection in China will inevitably result in significant conflicts between land use and ecological land use. The challenge lies in achieving sustainable high-quality development while simultaneously protecting the ecological environment, optimizing the land use structure, and promoting a harmonious relationship between humans and the land. These challenges are faced by all regions. Land use conflicts primarily occur in peri-urban areas characterized by prominent economic development and urban agglomeration. Previous studies have mainly focused on analyzing the effects of land use on habitat quality during intense urbanization. However, it is important to recognize that land pressure encompasses economic, ecological, and social aspects. To gain a comprehensive understanding of the spatial conflict of land use and the impact on habitat quality in Ankang, a city that has been advocating ecological protection for the past two decades, this study aims to objectively analyze the spatial trends in land use changes in such cities. Additionally, it aims to provide insights for the harmonious development of land use in eco-region-oriented cities. Using the SSP-RCP scenarios provided by CMIP6, this paper employs a system analysis method, PLUS model, InVEST model, and land use conflict measurement model to dynamically simulate the future habitat quality and spatial conflict patterns of land use in Ankang City. The study explores the spatial coupling effect of both factors under different scenarios. The results indicate the following:(1) Under different future shared socio-economic path scenarios, land use intensity and land conflict levels follow the order of SSP585 (high forcing scenario), SSP370 (medium to high forcing scenario), SSP245 (medium forcing scenario), and SSP126 (low forcing scenario), with intensity and conflict decreasing accordingly. (2) The overall development trend in Ankang City reveals an intensification of land use conflicts and a decrease in habitat quality. The expansion rate of construction land is increasing and exhibiting aggregation, while agricultural land area is expanding and forest land area is continuously decreasing. (3) Land use intensity exhibits a significant positive correlation with land conflict levels, while land conflict levels demonstrate a significant negative correlation with habitat quality. These findings suggest that land use has had some impact on the ecological environment, with indications of habitat degradation. Even in Ankang, where ecological development is highly valued, the city will gradually face conflicts between ecological protection and economic development in future scenarios. The study highlights that Ankang's future development space will be constrained within the context of environmental protection, leading to greater land use conflicts in urban and surrounding areas. Consequently, the quality of habitats will inevitably decline. Therefore, it is crucial to allocate sufficient space for economic development while simultaneously prioritizing ecological protection. This approach will ensure a healthy economic development trajectory and foster a harmonious relationship between humans and the land.

With the development of organizational biology and forced from the EU Cosmetic Regulation (EU/1223/2009) with the complete ban of animal testing for cosmetic purposes, 3D skin models have been widely developed due to their similar physiological structure and metabolic function to native human tissue. 3D skin models for in vitro cosmetic evaluation are still promising alternative methods for evaluating phototoxicity, corrosivity and irritation. These models have been used for early screening and later validation of toxicity and efficacy evaluation by many well-known cosmetic companies. 3D skin models have become an important tool in cosmetic evaluation research. This article reviews the development of 3D skin models and their application in cosmetic evaluation. An outlook on the current application and future technological development directions in the cosmetic field is also presented.

Although the neurofilament light chain (NfL) is used as a biomarker for neurodegenerative decline, its use in surgery- and anaesthesia-induced acute cognitive dysfunction remains controversial. We aimed to synthesise the evidence to explore the potential of NfL as an established biomarker for perioperative neurocognitive disorders (PND). We systematically searched the PubMed, EMBASE, MEDLINE, Cochrane Library electronic databases, and Cochrane Central Registry of Clinical Trials. Our results show that CSF NfL levels positively correlated with blood NfL levels (r = 0.63; 95% confidence interval [CI], 0.42-0.77). The pooled standardised mean difference (SMD) showed a significantly higher preoperative CSF NfL levels (SMD = 0.27; 95% CI, 0.07-0.47) and both pre- and postoperative blood NfL levels (SMD = 0.53, 95% CI, 0.40-0.66 and SMD = 0.58, 95% CI, 0.43-0.73) in the postoperative delirium (POD) group. Postoperative blood NfL levels were significantly elevated in both POD group (SMD = 0.49; 95% CI, 0.34-0.64) and no-POD group (SMD = 0.67; 95% CI, 0.53-0.81). Our meta-analysis indicates that NfL may serve as a potential biomarker for POD, and elevated preoperative blood NfL levels could be a risk factor for POD. Further studies are needed to confirm the association of CSF/blood NfL levels with other PND types.

We give a simple proof of the Chen inequality for the Chen invariant $\underbrace{\delta (2,...,2)}_{k\mbox{ terms}}$ of submanifolds in Riemannian space forms.

The Chen circuit system, a three-dimensional autonomous system with intriguing dynamics, has gained considerable attention due to its potential applications in diverse scientific fields. In this article, a Chen circuit-like system is defined and a comprehensive dynamics has been studied. The system exhibits chaotic dynamics, limit cycles, and bifurcations, making it a captivating subject of study. By employing numerical simulations and analytical techniques, we explore the system's stability and identify critical parameter values leading to qualitative changes. Notably, we delve Hopf bifurcations, which give rise to stability changes and the emergence of limit cycles. Furthermore, we analyze the fractal dimension of the system's attractor, providing insights into its complexity and self-similarity. Through a systematic examination of the Chen circuit-like system, we deepen our understanding of its intricate dynamics and offer valuable insights into the underlying mechanisms. The findings contribute to the field of dynamical systems and hold potential implications in areas such as chaos-based secure communications, signal processing, and nonlinear control. This work serves as a valuable reference for researchers and practitioners interested in the dynamics and bifurcation analysis of nonlinear systems.

The United Nations Sustainable Development Goals call for the eradication of poverty, and China has proposed the Rural Revitalization Strategy based on the achievements of its poverty alleviation efforts in 2020. As a vital component of this strategy, the impact of land transfer on farmers' income growth has become a hot topic in both theoretical and practical sectors. This paper utilizes data from the CFPS database for the years 2010-2018 to construct OLS regression models and a Heckman two-stage model to analyze the effects of land transfers on the incomes of different types and sources among farmers. The empirical results show: First, land transfers do promote income growth among farmers, but the effect is primarily positive for those transferring out land, with negligible impact on those acquiring land. Second, the impact of land transfers varies between different types of income for transferees and transferors. Wage income contributes up to 88.26% to the income growth of transferors, a significantly higher rate than the decrease in business income; however, the increase in business income for transferees does not offset the decline in wage income, leading to no significant change in overall income. Further sensitivity analysis using the Heckman two-stage model confirms the robustness of these findings. The conclusions of this study provide theoretical and empirical evidence to optimize land transfer policies, enhance participation in land transfers, and ultimately achieve the mission of rural revitalization.

This study used Dutch potatoes at the end of dormancy as the material to explore the impact of menthol (0.2 and 0.5 g/kg based on potato mass) treatment on sprouting inhibition and potato quality. The findings revealed that a menthol concentration of 0.5 g/kg effectively inhibited potato tuber sprouting and significantly reduced glucoside alkaloids production. After a storage period of 15 days, the sprouting percentage and glucoside alkaloids content of potatoes treated with 0.5 g/kg menthol were observed to be significantly lower at 4.17% and 68.63 mg/kg, respectively, compared to the control group which exhibited values of 100% and 282.01 mg/kg, respectively (P < 0.05). Throughout the storage period, 0.5 g/kg of menthol promoted respiration, reduced malondialdehyde production in potatoes, inhibited polyphenol oxidase activity, and slowed down tissue browning. Additionally, it mitigated the decline in starch and soluble protein content, inhibiting the accumulation of reducing sugars.

Calcium (Ca) is an essential element constituting sedimentary carbonate in subducting sediments. Ca isotopic characteristics of subduction-related rocks could provide insight into the behavior and budget of carbonate and carbon cycles in subduction zones, due to the distinctive δ^44/40Ca ranges of sedimentary carbonate with respect to the mantle. Here, we studied the Ca isotopic compositions of arc magmas from the Northern Luzon arc (NLA), which are evolved from a depleted mantle metasomatized by slab-derived fluids and sediment melts. The δ^44/40Ca values range from 0.76 ± 0.04‰ to 1.01 ± 0.03‰ and cover the typical ranges for bulk silica earth (BSE, ~ 0.94‰) and fresh mid-ocean ridge basalt (MORB, ~ 0.83‰). The Ca isotopes of NLA volcanics are not dominantly determined by the effects of mantle partial melting or fractional crystallization, nor significantly modified by secondary alteration. Instead, the δ^44/40Ca values of NLA volcanics are controlled by the subduction-related metasomatism. The metasomatism by slab-derived fluids (mainly expelled from altered oceanic crust, AOC) dramatically elevated the contents of fluid-mobile elements (e.g., Ba and Pb) with respect to fluid-immobile elements (e.g., Ce). This process, however, rarely modified the Ca isotopes, possibly ascribed to the δ^44/40Ca similarity between AOC and the depleted mantle. The δ^44/40Ca values significantly correlated with subduction indicators (e.g., Sr-Nd isotopes, Ba/Nb, Ce/Pb, and Nb/La), demonstrating the Ca isotopes of NLA volcanics are mainly controlled by the metasomatism of sediment melts subducting from the South China Sea (SCS). Based on the thermal structures and chemical compositions of sediments subducting into global trenches, we propose that carbonate Ca isotopic signals can only be observed in the arcs with high sedimentary Ca fluxes and temperature-pressure conditions well beyond the solidus of H₂O-saturated sediment melting, e.g., NLA, Nicaragua, Guatemala, Colombia, Peru, South Chile, North Vanuatu, New Zealand, and Kermadec. The absence of such signals in other arcs suggests either limited sedimentary fluxes or much of the subducting sedimentary carbonate has been survived during plate subduction to enter the deep mantle.

Herein, bamboo-laminated lumber for furniture was coated with waterborne acrylic paint. The effects of different painting techniques and quantities on the drying rate, smoothness, hardness, adhesion and wear resistance of the paint film were investigated. Then, the thermal properties of the paint were analysed using thermogravimetry and differential scanning calorimeter to examine the film-forming mechanism. The results showed that painting technique had no effect on the drying time, flatness, hardness and adhesion of the paint film, but it influenced the wear resistance. Herein, the films’ flatness showed little variation with different painting methods (one-layer primer one-layer topcoat, one-layer primer two-layer topcoat, two-layer primer one-layer topcoat and two-layer primer two-layer topcoat). The drying time for primer surfaces/solids was 8min/8.5 min, while it was 6.5/7 min for topcoats. The paint films exhibited grade B hardness and grade 0 adhesion and the better wear resistance when using one-layer primer one-layer topcoat at 51.24 mg·100 r−1. The amount of paint applied significantly affected the drying time and flatness of the paint film. As the quantity increased, the drying time of the paint’s surfaces and solids also increased, whereas the film’s flatness initially increased before decreasing. The film’s optimal adhesion, hardness and wear resistance values were grade 0, grade B and 51.24 mg·100 r−1, respectively, when 80 g/m2 of paint was applied. Thermal analysis of the primer and topcoat showed that water decomposition occurred at 100℃ and thermal decomposition of organic components occurred at 350℃. The primer and topcoat exhibited the same weight loss, but primer’s thermal loss rate was higher than that of topcoat. Consequently, the topcoat displayed better thermal stability than the primer.

An undescribed diterpene, stellerterpenoid A (1) and two undescribed sesquiterpenoids, stellerterpenoids B and C (2-3), together with six known compounds, were isolated from the roots of Stellera chamaejasme L. Their structures were elucidated by extensive spectroscopic data (1D, 2D NMR, IR, UV and HR-ESI-MS). The absolute configuration of 1-3 were elucidated based on ECD calculation. Among of them, stellerterpenoid A was a rare 13, 14 - seco nortigliane diterpenoid and stellerterpenoid B was a guaiacane type sesquiterpenoid with an unusual 1, 2-diketone moiety. The known stelleraguaianone B (5) exhibited moderate activity to suppress NO production in LPS - simulated macrophages with an IC50 value of 24.76 ± 0.4 μM. None of the compounds showed inhibitory influenza virus and tumor activity.

In hepatocellular carcinoma (HCC), recurrence usually occurs after curative surgical resection. Currently, no approved adjuvant therapy has been shown to reduce recurrence rates. In this report, the in vivo mouse effect of sequential combination treatment with recombinant mouse interferon-alpha (rmIFN-α) and an anti-mouse-PD1 antibody on hepatitis B virus (HBV) clearance was evaluated. A phase I clinical trial was then conducted to assess the safety, tolerability, and inhibitory activity of sequential therapy with ropeginterferon alfa-2b and nivolumab in HCC recurrence in patients who have undergone curative surgery for HBV-related HCC. In animal modeling, HBV suppression was significantly greater with rmIFN-α and anti-PD1 sequential combination treatment than with their treatment alone. In the Phase I study, eleven patients completed the sequential therapy with ropeginterferon alfa-2b every two weeks at the dose of 450 µg for six doses, followed by three doses of nivolumab every two weeks up to 0.75 mg/kg. A notable decrease or clearance of HBV surface antigen was observed in two patients. Dose-limiting toxicity of grade 3 alanine transaminase and aspartate aminotransferase increases was observed in one patient. The maximum tolerated dose was determined. Currently no HCC recurrence has been observed. The treatment modality was well tolerated. The data support further clinical development of sequential combination therapy as a post-surgery prophylactic measure against the recurrence of HBV-related HCC.

In recent years, the use of solid waste fillers to partially replace natural fillers in asphalt mixtures to produce high-performance asphalt mixtures has received widespread attention. However, differences in the material properties of solid waste fillers remain a problem for this recycling method. To address this issue, limestone powder in asphalt mixtures was replaced by three solid waste fillers (steel slag powder, tailings powder and calcium carbide slag powder) in this study. The chemical composition of the fillers was first characterized to assess the homogeneity of the material. Then, AC and SMA asphalt mixtures were designed and produced and characterized for wet stability. The results showed that asphalt mixtures with solid waste fillers were superior to LP asphalt mixtures in terms of resistance to water damage, and steel slag powder showed the best improvement in moisture stability of asphalt mixtures. The optimum substitution of solid waste filler for limestone filler was 25%. In addition, the moisture stability of asphalt mixture with limestone filler was significantly improved with the addition of anti-stripping agents. In contrast, the moisture stability of asphalt mixtures with solid waste filler was slightly improved. Solid waste fillers could be used in asphalt mixtures and have a similar function as the anti-stripping agent. In summary, the use of solid waste fillers to replace mineral fillers in asphalt mixtures is a reliable, value-added, recycling option.

Researches on flexible thermoelectric (TE) materials usually focus on conducting polymers (CPs) and CP-based composites; however, it is a great challenge to obtain high TE properties comparable to inorganic counterparts. Here, we report an n-type Ag₂Se film on flexible nylon membrane with an ultrahigh power factor ~987.4 ± 104.1 μWm⁻¹K⁻² at 300 K and an excellent flexibility (93% of the original electrical conductivity retention after 1000 bending cycles around a 8-mm diameter rod). The flexibility is attributed to a synergetic effect of the nylon membrane and the Ag₂Se film intertwined with numerous high-aspect-ratio Ag₂Se grains. A TE prototype composed of 4-leg of the hybrid film generates a voltage and a maximum power of 19 mV and 460 nW, respectively, at a temperature difference of 30 K. This work opens opportunities of searching for high performance TE film for flexible TE devices.

Digital images have become an important carrier for people to access information in the information age. However, with the development of the technology, digital images are vulnerable to illegal access and tampering, to the extent that they pose a serious threat to personal privacy, social order and national security. Therefore, image forensic techniques have become an important research topic in the field of multimedia information security. In recent years, deep learning technology has been widely applied in the field of image forensics and the performance achieved has significantly exceeded the conventional forensic algorithms. This survey compares the state-of-the-art image forensic techniques based on deep learning in recent years. The image forensic techniques are divided into passive and active forensics. In passive forensics, forgery detection techniques are reviewed, and the basic framework, evaluation metrics and commonly used datasets for forgery detection are presented. The performance, advantages and disadvantages of existing methods are also compared and analyzed according to different types of detection. In active forensics, robust image watermarking techniques are overviewed, the evaluation metrics and basic framework of robust watermarking techniques are presented. The technical characteristics and performance of existing methods are analyzed based on the different types of attacks on images. Finally, future research directions and conclusions are given to provide useful suggestions for people in image forensics and related research fields.

This paper first explains the theory of the origin of force from a new perspective, explaining that the origin of all forces is caused by the "missing of energy in the time dimension" (non-conservation in a certain period of time), and constructs a unified theory of force on this basis. Then, through the unified theory of force, the following phenomena are reinterpreted: (1) The common origin of the inverse square law of gravitation and electromagnetic force; (2) The origin of the repulsive force of electrons and protons at small distances; (3) The mystery of the rotation curve of galaxies and the new explanation of "dark matter"; (4) explain the origin of the magnetic field; (5) Predict that moving magnets have the same radiation effect as charged particles (electron magnetic moments also have radiation effects); (6) Reinterpret Maxwell's displacement current; (7) Reinterpret synchrotron radiation and bremsstrahlung; (8) Explain that the strong and weak forces are short-range forces; (9) Predict the true structure of black holes and the origin of gravitational waves;(10) Possible explanation for the origin of the speed of light.

In this study, we report a new epoxy acrylate based shape memory polymer(SMP) fabricated by Liquid crystal display (LCD) Stereolithographic 3D printing. The printed 3D object has a high resolution and high transparency in visible light region. The uniaxial tensile tests showed enhanced tensile toughness and tunable mechanical properties. The fix-recovery and cycle tests indicated high shape recovery properties including high shape recovery rate and excellent cycling stability. In addition, a smart electrical valve actuator was fabricated that can be used in fast heat or electricity responsive electrical circuits. LCD 3D printing provides a low-cost and high efficient way to fabricate fast responsive SMP, which can be used in wide applications in various fields on aerospace engineering, biomedical devices, soft robots and electronic devices.

Suitable soil structure and nutrient security are important for plant growth and development, characteristics of soil fractal dimension and distribution of physical and chemical properties and their interactions play an important role in studying the stability of soil structure and water and fertilizer cycles. As a sustainable management model, intercropping has positive benefits for erosion control, spatial optimization of resources, as well as improving system productivity. The effects of four intercropping methods on soil fractal dimension and physicochemical properties were investigated by intercropping Salvia miltiorrhiza with forage and S. miltiorrhiza with forest under typical karst rock desertification habitats in Guizhou. The results showed that soil nutrient content of intercropping was significantly higher than that of monoculture, the organic carbon content of soil grown under forest is higher than other treatments, and there was a non-significant change in soil water content of intercropping compared with monoculture. The soil fine-grained matter of intercropping was significantly higher than that of monoculture, while the soil fractal dimension showed a tendency to become larger with the increase of fine-grained matter. The intercropping planting, due to its component types and spatial and temporal configurations, leads to differences in soil water and fertilizer interactions, which can be combined with other ecological restoration measures to optimize the composite model and jointly promote the restoration and development of ecologically fragile areas.

This paper is another applied article based on the author's "Unified Theory of Force". The main work of this paper is as follows: (1) Reinterpretation of the Lorentz contraction effect and rigorous proof that the Lorentz contraction is a physical phenomenon based on the conservation of energy and momentum under non-completely symmetrical relative motion effects. This paper proves that the Lorentz contraction effect not only occurs in the direction of motion but also simultaneously in any direction. (2) For the first time, we attempted to explain the physical meaning of the Planck energy formula in theory and associate the Planck energy formula with the Lorentz contraction effect, which can help us to have a deeper understanding of the true physical meaning behind the Planck energy formula. At the same time, we also made reasonable theoretical predictions about the basic structure of photons.

There is currently no unified explanation for the origin of Earth's magnetic field, planetary magnetic fields, stellar magnetic fields, and neutron star magnetic fields, and most importantly, none of these theories have been experimentally verified. This paper is based on a new unified theory of mechanics and its derived applications, which may provide a better explanation for the origin of magnetic fields in celestial bodies and can be experimentally tested to better answer the observed phenomena: (1) the greater the mass of the celestial body, the stronger the magnetic field; (2) the faster the rotation speed of the celestial body, the stronger the magnetic field; (3) the higher the density of the celestial body, the stronger the magnetic field produced.

Abstract: Tumor-targeting and blood-brain barrier (BBB)-penetrating are highly desirable for the treatment of glioma. In this study, we developed Pep-1&borneol-bifunctionalized carmustin-loaded micelles (Pep-1/Bor/CMS-M) capable of targeting to IL-13 receptor-overexpressed glioma and penetrating the brain microvascular endothelial cells-associated physiologic barriers. Pep-1/Bor/CMS-M were nearly spherical particles with a dimeter of 32.6 ± 1.1 nm and zeta potential of -21.3 ± 3.1 mV. Carmustine (CMS) released from Pep-1/Bor/CMS-M in pH 7.4 was significantly faster than in acidic environments. In human glioma BT325 cellular studies, Pep-1/Bor/CMS-M remarkably increased the cytotoxicity, notably improved the internalization and effectively induced the cell apoptosis. Likewise, in human brain microvascular endothelial cells (HBMEC) cells, Pep-1/Bor/CMS-M obviously promoted the cellular uptake, rapidly decreased the transepithelial electrical resistance (TEER) and thereby of enhancing the ability of penetration. In orthotopic Luc-BT325 glioma tumor-bearing nude mouse models, the stronger fluorescence signal and longer retention were observed in brain tissues compared with other controls, after single administration of DiD-labelled Pep-1/Bor/M (DiD/Pep-1/Bor/M). Importantly, Pep-1/Bor/CMS-M displayed the strongest inhibition of tumor growth, the longest survival period and low systemic toxicity in treating orthotopic glioma tumor-bearing nude mice. Simultaneous functionalization of Pep-1 and borneol offers a novel strategy for designing CMS-based nanomedicine and precisely treating glioma.

This paper is mainly based on a stricter premise of the twin paradox and the assumption of inertial frame, discusses the properties of time and space under the premise of complete symmetry, and draws an interesting conclusion: the simultaneity of different reference frames is possible realized, and the space is relatively independent. And based on this, the twin paradox, cosmic inflation, ultra-distance action of quantum entanglement, microscopic space motion of particles, measurement problems and other phenomena are tentatively explained from a new angle. This interpretation is exploratory and new. At the same time, the author also proposes an experimental way to test the relative independence of space.At the same time, this paper attempts to strictly prove that Einstein's definition of simultaneity and spatial absoluteness in special relativity may be problematic.

In this paper, the quality change of scallop (Patinopecten yessoensis) in the process of anhydrous storage and transportation after cold-acclimation and induced dormancy was studied, and the regulation mechanism of quality degradation in the storage and transportation in the process of gradient chilling stress and drying exposure was further explored. The results show that while being transferred from anhydrous storage and transportation from hydrous storage and transportation, the breathing pattern of scallops were changed from aerobic to anaerobic. Their gill filaments were altered, and the apparent vitality was constantly declining, which was reflected by the edge shrinkage of pallium and the direct proportion between the edge reduction rate and the stimulus response period. After being in the anhydrous state for 4d, the AEC value dropped to 67.59%. At this time, if they were under hydration again, they would resume a nice growth state. By virtue of proteomics, it was revealed from the analysis that cold acclimation and dry exposure mainly led to changes in biological functions and pathways such as mitochondrial inner membrane and ATP hydrolysis activity. In addition, it can be seen from the functional annotation and enrichment analysis of the metabolite KEGG that cold acclimation promoted the purine metabolism of scallops, while dry exposure inhibited the metabolism of saturated fatty acids. Besides, in this study, the infrared sensing mode was used for the first time to record the heart rate changes of the scallops during circulation, which provides feasibility for the nondestructive vitality monitoring of Lamellibranchia.

This paper mainly explores the feasibility of using desert sand (DS) and recycled aggregate in cement stabilized base. Recycled coarse aggregate (RCA) and DS serve as the substitutes of natural coarse and fine aggregates, respectively, in cement stabilized base. A four-factor and four-level orthogonal test is designed to analyze the unconfined compressive strength, splitting tensile strength, and compressive resilient modulus. Furthermore, this paper investigates the effects of cement content, fly ash (FA) replacement rate, RCA replacement rate, and DS replacement rate on the road performance of cement stabilized base composing of RCA and DS. The test results reveal that the performance of cement stabilized base with partial RCA instead of natural coarse aggregate (NCA) and partial DS instead of natural fine aggregate satisfy the road use. Meanwhile, DS is beneficial to improve the strength of cement stabilized base. The correlation and microscopic analyses of the test results imply the feasibility of applying DS and recycled aggregate to cement stabilized base. It is hoped that this paper can offer a solid theoretical foundation for promoting the application of DS and recycled aggregate in road engineering.

Image encryption is increasingly becoming an important area of research in information security and network communications, as digital images are widely used in various applications and are vulnerable to various types of attacks. In this research work, a color image cryptosystem that is based on a 3-layer permutation-substitution network (PSN) is proposed. For every layer, an encryption key and an S-box are generated and utilized. Those are based on a four-dimensional (4D) dynamical Chen system of a fractional-order, the Mersenne Twister, OpenSLL, Rule 30 Cellular Automata and Intel’s MKL. The sequential application of Shannon’s ideas of diffusion and confusion for 3 times guarantees a total distortion of any input plain image, resulting in a totally encrypted one. Apart from the excellent and comparable performance to counterpart algorithms from the literature, showcasing resistance to visual, statistical, entropy, differential, known plaintext and brute-force attacks, the proposed image cryptosystem provides an exceptionally superior performance in 2 aspects: a vast key space of 2^1658 and an average encryption rate of 3.34 Mbps. Furthermore, the proposed image cryptosystem is shown to successfully pass all the tests of the NIST SP 800 suite.

The AREB/ABF (ABA response element binding) proteins in plants are vital for plant stress responses, but the understanding of AREB/ABFs in orchid species, an important traditional medicinal and ornamental plants, is limited. Here, twelve AREB/ABF genes were identified within three orchids’ complete genome and classified into three groups (groups I, II, and III) via a phylogenetic analysis, which was further supported by the analysis of their conserved motifs and gene structures. The cis-elements analysis showed that hormone response elements followed by light and stress responses were widely rich in AREB/ABFs. A prediction analysis of orchid ABRE/ABF-mediated regulatory network was further constructed through cis-regulatory elements (CREs) analysis of their promoter regions and revealed that several transcriptional factor (TF) gene family were abundant as the potential regulators for orchid AREB/ABFs. Expression profile analysis based on public transcriptomic data showed that most AREB/ABF genes have distinct tissue-specific expression patterns in orchid plants. Additionally, DcaABI5 as the homolog of ABA INSENSITIVE 5 (ABI5) from Arabidopsis was selected for further analysis. The results showed that Arabidopsis transgenic overexpressing DcaABI5 could rescue the ABA insensitive phenotype in the mutant abi5. Collectively, these findings will provide valuable information on AREB/ABF genes in orchids.

Glycoside Hydrolase 3 (GH3) is a phytohormone-responsive family of genes that has been found in many plant species. It is implicated in the biological activity of indolacetic (IAA) and jasmonic acids (JA), and also affects plant growth and developmental processes and some stresses. In this study, GH3 genes were identified in 48 plants, which belong to algae, moss, fern, gymnosperm and angiosperm. No GH3 representative gene has been found in algae, and our research identified 4 genes in mosses, 19 in ferns, 7 in gymnosperms, and numerous in Angiosperms. The results showed that GH3 genes mainly occur in seed plants. Phylogenetic analysis of all GH3 genes showed three separate clades. Group I was related to JA adenylation, group II was related to IAA adenylation, and group III was separated from group II but the function was not clear. The structure of GH3 protein indicated highly conserved sequence in the plant kingdom. The analysis of JA-adenylation related to gene expression of GH3 in potato (Solanum tuberosum) showed that StGH3.12 highly responded to Methyl Jasmonate (MeJA) treatment. Expression levels of StGH3.1, StGH3.11, and StGH3.12 were high in flower and StGH3.11 expression was also high in stolon. Our research revealed the evolution of the GH3 family, which is useful for studying the precise function about JA-adenylation GH3 genes in S. tuberosum under development and biotic stresses.

Waterlogging induced by rain in urban areas has a potential risk impact on property and safety. This paper focuses on the impact of rain on waterlogging and evaluates the waterlogging risk in the central city of Shanghai. A simplified waterlogging depth model is developed in different areas with different drainage capacity and rainfall in consumption of simplifying the effect of complex terrain characteristics and hydrological situation. Based on urban waterlogging depth and its classification collection, a Rain-induced Urban Waterlogging Risk Model(RUWRM) is further established to evaluate waterlogging risk in the central city. The results show that waterlogging depth is closely linked with rainfall and drainage, with a linear relationship between them. More rainfall leads to higher waterlogging risk, especially in the central city with imperfect drainage facilities. Rain-induced urban waterlogging risk model can rapidly gives the waterlogging rank caused by rainfall with a clear classification collection. The results of waterlogging risk prediction indicate that it is confident to get the urban waterlogging risk rank well and truly in advance with more accurate rainfall prediction. This general study is a contribution that allows the public, policy makers and relevant departments of urban operation to assess the appropriate management to reduce traffic intensity and personal safety or strategy to lead to less waterlogging risk.

In the manufacturing of optical lenses, the lack of digital monitoring and inspection for centring processing not only results in product consistency not being guaranteed but also leads to inefficiency in processing. A centring processing digital twin system is proposed to address the problems of low virtual visualization and insufficient monitoring capability of centring processing of high-precision optical components. The layered architecture of the system is determined based on the five-dimensional model of the digital twin, coupled with a dimension-driven geometric model and a physical model that integrates data and turning mechanisms to improve the fidelity and interactivity of the virtual model of the centring lathe. The fusion of heterogeneous data from multiple sources in the centring machining process at the semantic and physical levels is realized by using an information model and an OPC UA-based data interaction method. The VMD-GRU method based on feature fusion is used to monitor the key components of the centring lathe. Finally, the feasibility and effectiveness of the proposed method are verified by a case study of the development of a digital twin system for centring lathe, which provides a reference for the digitization and intelligence of the machining process of high-precision optical components.

For a long time, physicists always directly use mathematical tools to deal with physical problems, and few people pay attention to the difference between mathematical theory and physical theory. Just like the dilemma that physicists once faced when dealing with the problem of blackbody radiation function.By analyzing the difference between the theoretical basis of mathematics and the theoretical basis of physics, this paper draws the following conclusions: (1) The theoretical basis of mathematics and the theoretical basis of physics are different, so when we use mathematical tools for physics research, we need to be very careful. (2) Finiteness and discreteness should be the basis of the whole physical theory; This paper points out that it is not advisable to use infinite " " and infinitesimal "0" without restriction and demonstration in physics, as well as the continuity of functions, which will bring a lot of trouble to physical theory.At the same time, through the analysis of Banach-Tarski paradox and Bertrand paradox, this paper proposes that if we revise the basic assumptions of probability theory: assuming that "points" have quantized sizes, and "lines" also have quantized widths. After the correction, we can not only avoid the troubles caused by Bertrand paradox, but also make probability theory better for practical application.

Coalbed Methane(CBM) production enhancement for single wells is a big problem to CBM industrialization. Low production is due to insufficient gas generation by thermogenic. Luckily, Biogenic gas was found in many areas and its supply is assumed to improve coalbed methane production. Therefore, microbial simulation experiment will demonstrate the effectiveness of the assumption. From microbial simulation experiment on different coal ranks, it is found that microbes can use coals to produce biogas under laboratory conditions. With different temperatures for different experiments, it turns out that the gas production at 35 ℃ is greater than that at 15℃,indicating that 35℃ is more suitable for microbes to produce gas. According to quantitative experiments, adding exogenous nutrients or exogenous bacteria can improve CBM production. Moreover, the production enhancement ratio can reach up to 115% under the condition of adding exogenous bacterial species, while the ratio for adding nutrients can be up to 144%.

In recent decades, with the ever-growing scale of video data, near-duplicate videos continue to emerge. Data quality issue caused by near-duplicate videos is becoming more and more prominent, which has affected the application of normal videos. Although current studies on near-duplicate video detection can be helpful to uncover data quality issues for videos, they still lack a process of automatic merging for the video data represented by high-dimensional features, which are difficult to automatically clean the near-duplicate videos to improve data quality for video datasets. At present, there are few studies on near-duplicate video data cleaning. The existing studies have the sensitive problems of video data orderliness and clustering initial center under a condition that prior distribution is unknown, which seriously affect the accuracy of near-duplicate video data cleaning. To address the above issues, an automatic near-duplicate video data cleaning method based on a consistent feature hash ring is proposed in this paper. First, a residual network with convolutional block attention modules, a long short-term memory deep network, and an attention model are integrated to construct an RCLA deep network with the multi-headed attention mechanism to extract spatiotemporal features of video data. Then, a consistent feature hash ring is constructed, which can effectively alleviate the sensitivity of video data orderliness while providing a condition of near-duplicate video merging. To reduce the sensitivity of the initial cluster centers to results of near-duplicate video cleansing, an optimized feature distance-means clustering algorithm is constructed by utilizing a mountain peak function on a consistent feature hash ring, which can implement automatic cleaning of near-duplicate video data. Finally, experiments are conducted based on a commonly used dataset named CC_WEB_VIDEO and a coal mining video dataset. Compared with some existing works, simulation results demonstrate that the performance of the proposed method.

In order to investigate the vertical distribution pattern of soil fauna community in low-altitude mountain areas. On July 8th, 2022, a low hill was selected as the study area to collect soil arthropods were collected through trap. Leaf litter, vegetation type and distribution quantity were investigated at each sampling site while soil fauna were collected. Also, the soil physical and chemical parameters were measured simultaneously. The results of one-way ANOVA showed that there were significant differences (P

: During the period of COVID-19, the Chinese government implemented a series of actions to prevent the spread of the virus. It is noticed that these preventive actions have generated positive effects on air pollution in Wuhan and Beijing. And, due to the differences in city functions, geographic locations, meteorological conditions, and preventive action details between the two cities, noticeable difference is observed on how they reduced air pollution. This unfortunate incident has become a social sample for studying the industrial and livelihood activities impact on air pollution, otherwise would be highly impossible. This paper starts from observing data from NASA's real-time fine particulate matter (PM2.5) and NO2, and comparing the air pollution in this special time domain with previous years. It is discovered that both PM2.5 and NO2 have been reduced in Wuhan, while only NO2 has significant reduction in Beijing, during the COVID-19 responses. This suggests that the human activity suppression by the COVID-19 control yields different effects on different pollutants and in different cities. Possible reasons for such effects are analysed by considering the public health control levels as well as the pollutant migration, industrial activities, and the weather conditions.

Balanced and coordinated economic development across regions is a critical goal of regional economic development and new-type urbanization in China. However, few studies have examined economic growth convergence clubs at the county level. To extend the research on convergence clubs, this research applies a log t convergence test and a dynamic spatial ordered Probit model (DSOP) to endogenously identify economic growth convergence clubs in counties and to examine the influence of initial states and structures on club convergence probability. The study sample covers 2286 counties of China from 1992 to 2010. The results show significant convergence club patterns at the county levels, resulting in the gradual formation of six convergence clubs. The DSOP estimation results show that per capita fixed assets, population density and industrialization have promoted convergence club formation to varying degrees.

The development of new diabetes drugs continues to be explored. Loureirin B, a flavonoid, extracted from Dracaena cochinchinensis, has been confirmed to increase insulin secretion and decrease blood glucose levels. For understanding the mechanism, a series of experiments had been employed based on computational methods and cell experiments. The insulin secretion significantly increased with the incubation of 0.01μM loureirin B for 4 hours. The viability of Ins-1 cells showed no significant difference with the treatment of loureirin B. Through computational methods, we hypothesized that loureirin B could interacts with K_ATP channels to promote insulin secretion. In cell experiments, it could be found that the current of K_ATP channel of Ins-1 cells was inhibited by the effect of loureirin B. After then, the voltage-dependent calcium channels were activated, the increase of Cx43 protein expression might mediate the Ca²⁺ to the intracellular. In summary, it could be concluded that loureirin B promoted insulin secretion mainly through inhibiting K_ATP current, the influx of Ca²⁺ to the Intracellular and the expression of Cx43.

The hump feature is one of the major instabilities in pump-turbines. When pump-turbines operate in the hump region, strong noise and serious fluctuations can be observed, which are harmful to their safe and stable operation and can even destroy the whole unit as well as water conveyance system. In this paper, a low specific speed (n_q = 36.1 min⁻¹) pump-turbine model was experimentally investigated. Firstly, the hump characteristic was obtained under 19 mm guide vane opening conditions. More interestingly, when the hump characteristic was measured in two directions (increasing and decreasing the discharge), characteristic hysteresis was found in the hump region. The analysis of performance characteristics reveals that the hump instability is the result of Euler momentum and hydraulic losses, and different Euler momentum and hydraulic losses in the two development processes lead to the hysteresis phenomenon. Then, 12 pressure sensors were mounted in the different parts of the pump-turbine model to obtain the time and frequency characteristics. The analysis of the corresponding fast Fourier transform confirms that the hump characteristic is related to low-frequency (0.04–0.15 times rotational frequency) vortices. The occurrence and cessation of vortices depend on the operating condition and measurement direction, which contribute to the hysteresis feature. Finally, the type of the low-frequency vortices was analyzed through the cross power spectrum.

In this paper, the effects on the rheological properties, particle size distribution, and fluorescence properties of red wine were investigated under microwave irradiation, and the mechanism of the effects of microwave irradiation on the sensory properties of red wine was discussed. The results showed that the effect of microwave on the rheological properties in red wine could be fitted by the Power-law model and Carson model, through the analysis of the rheological constants, yield stress, and viscosity coefficient of wine, it was found that microwave treatment could improve leg phenomenon and thickening effect by the change of rheological properties; the particle size distribution in wine indicated that microwave irradiation did change the particle size distribution through friction effect and oxidative polymerization, resulting in the wine’s visual effect and mouthfeel; the wine quality could be improved by enhancing the fluorescence intensity under different microwave conditions, which meant that microwave technology could speed up the formation of fluorescent substances, such as the polymerization of flavan-3-ols. In conclusion, microwave treatment could modify the sensory characteristics of wine, and further provide the theoretical basis for the application of microwave in winemaking.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

In the broad context of vulnerability detection, deep learning has achieved considerable progress but faces generalization challenges in multilingual environments . We introduce a novel approach named AST-FMVD, which leverages transfer learning and abstract syntax trees. By employing semantic similarity clustering and context-aware technology, the method constructs node mapping relationships between different languages, enabling zero-shot learning in vulnerability detection. The method was validated by applying Java's vulnerability detection model in the Python domain, successfully demonstrating that AST-FMVD retains the original model's detection capabilities in the target domain. In conclusion, the proposed method offers a promising solution to the inherent problems in multi-language vulnerability detection, signifying a potential leap in the application of deep learning, transfer learning, and abstract syntax trees for improved cross-domain performance.

This paper presents a theory on graph topological structure and graph coloring, proving that for any N-order graph structure (with a topological structure similar to ), the maximum number of colors required for coloring is less than or equal to . The Four Color Theorem is just one special case of this theory, with the maximum structure size for a four-color graph being a 4-order structure graph, hence requiring only a maximum of 4 colors for coloring.

This paper is the third application-oriented paper based on the "unified theory of forces" and also addresses the shortcomings of previous research in fully explaining the origin and nature of the weak force. The main conclusions of this paper are as follows: (1) It is argued that neutrinos are generated by the gravitational field, and their generation mechanism is similar to the radiation of photons from electron orbital transitions. Particles undergoing orbital transitions in a gravitational field will emit neutrinos. (2) We rigorously derive the energy formula for neutrinos and demonstrate that the energy formula for neutrinos does not comply with the Planck energy formula. Neutrinos with higher energy have longer wavelengths and are more easily observed in experiments.

The mesoporous heteroatom molecular sieve MCM-41 bulk crystals with the crystalline phase were synthesized via a one-step hydrothermal method using an ionic complex as template. The ionic complex template was formed by interaction between cetyltrimethylammonium ions and metal complex ion [M (EDTA)]2- (M=Co or Ni ). The materials were characterized by X-ray diffraction, scanning electron microscopy, high-resolution transmission electron microscopy, N2 adsorption–desorption isotherms, and X-ray absorption fine structure spectroscopy. The results showed that the materials possess a highly ordered mesoporous structure with the crystalline phase and possess high uniform ordered arrangement channels. The structure is in the vertical cross directions with a crystalline size of about 12 µm and high specific surface areas. The metal atoms were incorporated into the zeolite frameworks in the form of octahedral coordinate and have a uniform distribution in the materials. The amount of metal complexes formed by metal ion and EDTA is an essential factor for the formation of the vertical cross structure. Comparing to Si-MCM-41, the samples exhibited better conversion, higher selectivity for cumene cracking.

In agriculture, soil-borne fungal pathogens, especially Fusarium oxysporum strains, are posing a serious threat to efforts to achieve global food security. In the search for safer agrochemicals, silica nanoparticles (SiO2NPs) have recently been proposed as a new tool to alleviate pathogen damage including Fusarium wilt. Hollow mesoporous silica nanoparticles (HMSNs), a unique class of SiO2NPs, have been widely accepted as a desired pesticide carrier. However, their role in enhancing the disease resistance and the specific mechanism remain unknown. In this study, three sizes of HMSNs (19, 96 and 406 nm as HMSNs–19, HMSNs–96 and HMSNs–406, respectively) were synthesized and characterized to determine their effects on seed germination, seedling growth, and Fusarium oxysporum f. sp. phaseolus (FOP) suppression in cowpea roots by foliar spray using phenotypes, fresh biomass and disease progression as indicators. The results revealed that three HMSNs exhibited no adverse impacts on seed germination and tended to improve plant growth. Also, they exert their FOP suppression with a size- and concentration-dependent manner. HMSNs–406 possessed the best control effect at a concentration of 1000 mg/L showing an upto 40.00% decline in the disease severity. The Si(OH)4 control was also effective on FOP suppression at a lower concentration of 100 mg/L, whereas its higher concentrations exhibited obviously adverse impacts on FOP control, seed germination and plant growth. Moreover, we conformed that HMSNs posed their Fusarium wilt suppression in cowpea plant by activating SA (salicylic acid)-dependent SAR (systemic acquired resistance) responses rather than directly suppressing FOP. A higher level of SA content and elevated expression of its maker genes of PR-1 and PR-5 in HMSNs–406 treated cowpea roots provided substantial evidences of this mode of action. Other resistance-related genes, as well as defense-responsive enzymes, were also involved in the HMSNs-activated SAR pathway. Overall, for the first time, our results extended a new role of HMSNs as a potent elicitor to serve as a versatile alternative for plant disease protection of low cost, highly efficiency and sustainability.

At the end of 2019, while the world was being hit by the COVID-19 virus and, consequently, was living a global health crisis, many other pandemics were putting humankind in danger. The role of social media is of paramount importance in these kinds of contexts since they help health systems to cope with emergencies by contributing to conducting some activities such as the identification of public concerns, the detection of infections’ symptoms, and the traceability of the virus diffusion. In this paper, we have analyzed comments on events related to cholera, ebola, HIV/AIDS, influenza, malaria, Spanish influenza, swine flu, tuberculosis, typhus, yellow fever, and zika, collecting 369,472 tweets from the 3rd of March to the 15th of September, 2022. Our analysis has started with the collection of comments composed of unstructured texts on which we have applied natural language processing solutions. Afterward, we have employed topic modelling and sentiment analysis techniques to obtain a collection of people’s concerns and attitudes toward these pandemics. According to our findings, people's discussions were mostly about malaria, influenza, and tuberculosis and the focus was on the diseases themselves. As regards emotions, the most popular were fear, trust, and disgust where trust is mainly regarding HIV/AIDS tweets.

The theory of fractional calculus extends the order of classical integer calculus from integer to non-integer. As a new engineering application tool, it has made many important research achievements in many fields, including image processing. This paper mainly studies the application of fractional calculus theory in image enhancement and denoising, including the basic theory of fractional calculus and its amplitude frequency characteristics, the application of fractional differential operator in image enhancement, and the application of fractional integral operator in image denoising. The experimental results show that the fractional calculus theory has more special advantages in image enhancement and denoising. Compared with the existing integer order image enhancement operators, the fractional differential operator can more effectively enhance the "weak edge" and "strong texture" details of the image. The fractional order integral image denoising operator can not only improve the signal-to-noise ratio of the image compared to traditional denoising methods, but also better preserve detailed information such as edges and textures of the image.

Steam Generator Level Control System (SGLCS) is one of the key instrumentations and control subsystems to ensure the safe operation of nuclear power plants. It is highly recommended to perform reliability analysis for SGLCS for making better maintenance strategy. SGLCS is a digital control system with complex redundant configuration and failure\self-diagnosis\repair action, traditional fault tree is not applicable due to its static property, Markov model is not a good choice too because of heavy burden of creating state transition graph for even medium-size system. Boolean Logic Driven Markov Process (BDMP) can describe complex failure-repair state transition via ‘trigger link’ and three kinds of leaf nodes, as well as keep compact and easy-read struct like fault tree. So BDMP is adopted to analysis reliability of SGLCS. Graphical BDMP modeling environment KB3 and Monte Carlo simulator YAMS is used for BDMP modeling and quantitative analysis respectively, and unavailability of SGLCS is obtained. The contribution of three parts of SGLCS to the unavailability of the system is also evaluated, and it is found that the water supply flow control part contributes the most to the failure of SGLCS.

Ti and its alloys are the most commonly used materials for biomedical applications. However, bacterial infection after implant placement is still one of the significant rising complications. Therefore, the application of the antimicrobial agents into implant surfaces to prevent implant-associated infection has attracted lots of attention. Scientific papers have shown that inorganic antibacterial metal element (e.g. Ag, Cu, Zn) can be introduced to implant surfaces with the addition of metal nanoparticles or metallic compounds into electrolyte via micro-arc oxidation (MAO) technology. In this review, the effects of the composition and concentration of electrolyte and process parameters (e.g. voltage, current density, oxidation time) on morphological characteristics (e.g. surface morphology, bonding strength), antibacterial ability and biocompatibility of MAO antimicrobial coating were discussed in detail. Anti-infection and osseo-integration can be simultaneously accomplished with the selection of the proper antibacterial elements and operating parameters. Besides, MAO assisted by magnetron sputtering (MS) to endow Ti-based implant materials with superior antibacterial ability and biocompatibility was also discussed. Finally, the development trend of MAO technology in the future was forecasted.

This study presented a novel and sustainable method for producing chitin nanocrystals (PA-ChNCs) using phosphoric acid hydrolysis. The produced PA-ChNCs were used as stabilizers for Pickering emulsions and their physicochemical properties as well as stabilization mechanisms were systematically investigated. The PA-ChNCs exhibited small particle sizes and high surface areas, enabling an effective adsorption at the oil/water interface, which prevented coalescence in Pickering emulsions. The particle size and surface charge PA-ChNCs were strongly pH-dependent, which were critical factors for stabilizing Pickering emulsions. The study showed that emulsions with higher O:W ratios (50%) exhibited larger droplets but greater viscosity, forming a stable gel-like matrix that was more stable than emulsions with other O:W ratios after storage for 30 days. Emulsions with higher PA-ChNCs concentrations (2.0 wt%) and higher pH values (pH 10) showed small droplets and high viscosity, leading to stable emulsions. This research contributes to the development of sustainable and effective emulsifiers for use in the food industry, making utilization of seafood waste in an eco-friendly manner possible. Overall, this study highlights the potential of using newly developed PA-ChNCs as stabilizers for Pickering emulsions in food products.

The electroencephalogram (EEG) is a record of brain activity. Brain Computer Interface (BCI) technology formed by the EEG signal has become one of the hotspots at present. How to extract the feature signal of EEG is the most basic research of BCI technology. In this paper, A new method of recognizing fatigue, conscious, concentrated state of human brain is proposed by the combination of discrete wavelet transform and the neural network based on EEG signal. First of all, the law signal is preprocessed by the wavelet denoising method because the law EEG signal contains a large number of high frequency noise, which is decomposed into multi-layer high frequency signal and low frequency signal. thus, δ wave, θ wave, α wave, β wave are obtained by the wavelet transform. And then, frequency band energy of the different wave is regards as the feature signal of EEG. In the experiment, the feature signal is classified by radial basic function (RBF) and annealed chaotic competitive learning network (ACCLN). RBF and ACCLN networks are trained with 500 sets of sample data and are tested by 100 sets of samples in different mental states. The experimental results show that the average accuracy of RBF network under three conditions are 88.75%, 88.25%, 88.5%, respectively, and the correct rate of ACCLN network is 97%, 98%, 98%, respectively.

Excretory-secretory products (ESPs) are the main research targets for investigating the hosts and helminths interaction. Parasitic worms can migrate to parasitic sites and avoid the host immune response by secreting this product. Angiostrongylus cantonensisis an important food-borne zoonotic parasite that causes severe neuropathological damage and symptoms, including eosinophilic meningitis or meningoencephalitis in humans. Benzaldehydes are organic compounds composed of a benzene ring and formyl substituents. This compound has anti-inflammatory and antioxidation properties. Previous studies showed that 3-hydroxybenzaldehyde (3-HBA) and 4-hydroxybenzaldehyde (4-HBA) can reduce apoptosis in A. cantonensis ESPs treated astrocytes. These results on the protective effect underlying benzaldehyde have primarily focused on cell survival. The study was designed to investigate the molecular mechanisms of endoplasmic reticulum stress (ER stress) and oxidative stress in astrocytes in A. cantonensis ESPs treated astrocytes and to evaluate the therapeutic consequent of 3-HBA and 4-HBA. First, we initially established the RNA-seq dataset in each group, including Normal, ESPs, ESPs+3-HBA, and ESPs+4-HBA. We also found that benzaldehyde (3-HBA and 4-HBA) can stimulate astrocytes to express ER stress-related molecules after ESP treatment. The level of oxidative stress could also be decreased in astrocytes by elevating antioxidant activity and reducing ROS generation. These results suggested that benzaldehyde may be a potential therapeutic compound for human angiostrongyliasis to support brain cell survival by inducing the expression levels of ER stress- and oxidative stress-related pathway.

The degree of ore rock fragmentation of mine blasting is an important index for evaluating the effect of engineering blasting. In order to study the effect of millisecond delayed blasting on the internal fragmentation of the ore rock, LS-DYNA numerical simulation software was used to obtain the damage characteristics of the ore rock in the blasting area using the RHT model. The Mohr-Coulomb strength damage criterion was applied to analyze the internal stress state of the ore rock, and the effects of 25ms, 50ms and 75ms delay time conditions on ore rock fragmentation were studied. The results show that, within a certain range of delay time, the degree of rock fragmentation increases with the increase of delay time. The stress state in the ore rock due to blasting is strengthened with the increase of delay time in the direction of the blast hole, which shows that the stress concentration is strengthened from the excavation face to the interior of the ore rock. The damage and the degree of fragmentation show a characteristic relationship of 25ms＜50ms＜75ms, which is verified by carrying out blasting experiments on site.

In order to study the performance of a new type of cement-based grouting material under the coupling effect of freezing-thawing cycle and sulfate attack, experiments were designed and carried out. The damage mechanism of the material under the coupling effect of freezing-thawing and Na2SO4 solution was analyzed by measuring the mass change, relative dynamic elastic modulus, compressive strength loss and microstructure of the new grouting material. With increasing freeze-thaw cycles, mass loss and compres-sive strength loss of the sample in 15% Na2SO4 solution gradually increase, and the relative dynamic elastic modulus gradually decreases. During a 30-cycle freeze-thaw cycle, the mass loss rate, compressive strength loss rate, and relative dynamic elastic modulus of the sample are 4.17%, 24.59%, and 84.3%, respectively, showing good corrosion resistance and frost resistance durability. Microscopic analysis showed that SO42- caused the decomposition of C-S-H gel in the sample and the formation of Gypsum, and the widening of crack width aggravated the internal deterioration, indicating that the material deterioration rate increased under the dual-factor coupling effect.

Concrete cracks and local damage can affect the bond performance between concrete and steel bars, thereby reducing the durability of reinforced concrete structures. Compared with general concrete crack repair methods, biomineralization repair not only has effective bonding capabilities but is also particularly environmentally friendly. In view of this, this study aimed to apply biomineralization technology to repair damaged fiber-reinforced lightweight aggregate concrete (LWAC). Two groups of LWAC specimens were prepared. The control group used lightweight aggregates (LWAs) without bacterial spores and nutrient sources, and the experimental group used LWAs containing bacterial spores and nutrient sources. These specimens were first subjected to compression tests and pull-out tests, respectively, and thus were damaged. After the damaged specimen healed itself in different ways for 28 days, secondary compression and pull-out tests were conducted. The self-healing method of the control group involved placing the specimens in an incubator. The experimental group was further divided into experimental group I and experimental group II. The self-healing method of experimental group I was the same as that of the control group. The self-healing method of experimental group II involved soaking the specimen in a mixed solution of urea and calcium acetate for two days, and then taking it out and placing it in an incubator for two days, with a cycle of four days. The test results showed that, compared with the control group specimens, the relative bond strength ratio of the experimental group II specimens increased by 17.9%. Moreover, the EDS and XRD analysis results confirmed that the precipitate formed at the crack was calcium carbonate, which improved the compressive strength and bond strength after self-healing. This indicates that the biomineralization maintenance method used in experimental group II is more effective.

This study takes a two-echelon agricultural products supply chain (APSC) composed of an agricultural product processor (processor) and an agricultural product supermarket (supermarket) as the research object. In order to ensure the stable supply of high-quality agricultural products, this paper considers both fairness concern and corporate social responsibility (CSR), and establishes four Stackelberg game models with or without considering fairness concern and CSR, and obtains the influence mechanism of fairness concern and CSR on bilateral quality efforts in APSC through comparative analysis and numerical analysis. Research shows that the supermarket’s fairness concern can take the role of "profit distribution mechanism", but it is not conducive to improving bilateral quality efforts resulting in the inability to improve market demand, and it is not conducive to improving the utility of the supply chain system and consumer surplus; both members of APSC sharing CSR can not only improve the quality of agricultural products and promote the expansion of market demand, but also can achieve Pareto improvement of both profit of all members and supply chain system. Besides, The CSR shared by both members has a greater impact on bilateral quality efforts decision than the supermarket’s fairness concern, and thus the positive effect of CSR can overcome the negative effect of supermarket’s fairness concern.

The commercial oxygen-free copper sheets were cold-rolled with reduction rates ranging from 20% to 87% reduction rate and annealed at 400, 500 and 600 °C. The microstructure and texture evolution during cold-rolling and annealing processes were studied using optical microscopy (OM), the scanning electron microscopy (SEM) and the electron back-scattered diffraction (EBSD). The results show that the deformation textures of {123} (S) , {112} (Copper) and {110} (Brass) were continuously enhanced with the increase of cold-rolling reduction. The orientations along the α-oriented fiber converged towards Brass and the orientation density of β fiber obviously increased when the rolling reduction exceeded 60%. The recrystallization texture was significantly affected by the cold-rolling reduction. After 60% cold-rolling reduction, Copper and S textures components gradually decreased and {011} recrystallization texture component formed with the increase of annealing temperature. After 87% cold-rolling reduction, a strong Cube texture formed and other textures were inhibited with the increase of annealing temperature. The strong Brass and S deformation texture was conducive to the formation of a strong Cube annealing texture. The density of annealing twin boundary decreased with the increase of annealing temperature, and more annealing twin boundaries formed in the oxygen-free copper sheets with the increase of cold rolling reduction.

Abies beshanzuensis, an extremely endangered species, attracts serious concerns on genetic diversity recovery and population protection. However, little genetic information was known about it till now. In this study, intra-/intergenomic ITS variation, secondary structure, and molecular phylogeny of A.beshanzuensis were determined by nrDNA-ITS marker, and results indicated that, ITS region featured rich polymorphism in ITS1 and highly conservative in 5.8S/ITS2 among intra-/inter-genome, implying rich genetic diversities and the occurrence of non-concerted evolution in ITS region. Predicated 5.8S structure possessed Helices-Loops with 3 motifs (M1/M2/M3) and 5 helices B4-B8, and ITS2 could form conservative Clover-like structure with 5 ribotypes, manifesting genetically structural generalities and individualities. Thirteen ITS pseudogenes were also identified from 76 samples (or clones). Molecular phylogeny revealed that, A.beshanzuensis shared genetically closer relationships with A.fanjingshanensis, A.chensiensis, A.yuanbaoshanensis among genus Abies. The available original data provided rich genetic information on ITS sequence, structure and molecular phylogeny of A.beshanzuensis, which not only updated the databases of ITS sequences as well as secondary structures essential for phylogenetic reference and DNA barcoding analyses, but also contributed to deep exploration of population diversities, origin and evolution as well theoretical direction for population recovery and protection of A.beshanzuensis.

In order to correct attenuated millimeter-wavelength (Ka-band) radar data and address the problem of instability, an attenuation correction methodology (attenuation correction with variation trend constraint; VTC) was developed. Using synchronous observation conditions and multi-band radars, the VTC method adopts the variation trends of reflectivity in X-band radar data captured with wavelet transform as a constraint to adjust reflectivity factors of millimeter-wavelength radar. The correction was evaluated by comparing reflectivities obtained by millimeter-wavelength cloud radar and X-band weather radar. Experiments showed that attenuation was a major contributory factor in the different reflectivities of the two radars when relatively intense echoes exist, and the attenuation correction developed in this study significantly improved data quality for millimeter-wavelength radar. Reflectivity differences between the two radars were reduced and reflectivity correlations were enhanced. Errors caused by attenuation were eliminated, while variation details in the reflectivity factors were retained. The VTC method is superior to the bin-by-bin method in terms of correction amplitude and can be used for attenuation correction of shorter wavelength radar assisted by longer wavelength radar data.

There is no doubt that seagrass beds constitute one of the most productive ecosystems in shallow coastal waters. Despite this, picoplankton in seagrass ecosystems has received relatively little attention. The purpose of this study was to compare picoplankton growth and mortality rates between seagrass and unvegetated habitats using chamber incubations. We tested two main hypotheses: (i) incubation with seagrass would result in higher bacterial growth rates due to increased DOM release from seagrass photosynthesis, and (ii) Synechococcus spp. would be lower in the presence of seagrass due to competition for inorganic nutrients. Our results showed bacterial growth rates of 2.31 and 2.44 d–1 without and with seagrass, respectively. In seagrass chambers, bacterial growth was higher than that in non-seagrass chambers, suggesting that organic carbon coming from the seagrass community may support bacterial production. Furthermore, we observed a negative Synechococcus spp. growth rate (-0.9 d–1) in the seagrass treatment, likely reflecting nutrient competition with the seagrass. Small-scale chambers proved to be a useful tool for studying the factors controlling spatial and temporal patterns of picoplankton across different habitats. Furthermore, future studies should examine picoplankton growth over a wider range of spatial scales in seagrass beds and adjacent unvegetated sediment.

Abstract In order to solve the problem that it is difficult to obtain the accurate trigger signal moment when using the time difference of UAV flight acoustic signals collected by acoustic sensors arranged in advance to locate the position of UAVs when they cannot be tracked by radar and are difficult to be observed by the human eye, an acoustic source localisation method with improved empirical modal decomposition (REMD) under an adaptive frequency window is proposed. Firstly, the collected UAV flight signals are smoothed and filtered, then the robust empirical modal decomposition (REMD) is used for IMF modal decomposition and spectral analysis of the collected signals, and a panning frequency window with variable bandwidth is introduced for corresponding frequency locking and extracting the IMFs; the GWO optimisation is used and the sliding metrics are set to determine the position of the panning frequency window automatically; finally, the extracted Finally, the extracted IMF components are reconstructed according to the criterion, and the trigger signal moments in the reconstructed IMF components are resolved and recorded, and the algorithm is used to calculate the difference between the reception moments of different sensors; for the traditional sound source localisation algorithms with a small detection range, which are prone to fall into the no-solution or false-solution, i.e., unable to achieve the localisation, a weighted least-squares-based Chan-Taylor algorithm is proposed for the localisation computation, and a weighted least-squares algorithm is proposed for the localisation computation, through the Inputting the sensor delay parameter and solving the linear equation system to get the target position information; finally, this paper verifies the robustness and performance of the design method with simulated and actual signals. The results show that the maximum positioning error is no more than 5% in an area with a side length of 15m in the measurement area. With the improved accuracy of time delay estimation, the positioning simulation results meet the positioning requirements even though the positioning error is further expanded when the measurement area is further expanded.

In order to solve the problem of feature extraction of underwater acoustic signals in complex ocean environment, a new method for feature extraction from ship radiated noise is presented based on empirical mode decomposition theory and permutation entropy. It analyzes the separability for permutation entropies of the intrinsic mode functions of three types of ship radiated noise signals, and discusses the permutation entropy of the intrinsic mode function with the highest energy. In this study, ship radiated noise signals measured from three types of ships are decomposed into a set of intrinsic mode functions with empirical mode decomposition method. Then, the permutation entropies of all intrinsic mode functions are calculated with appropriate parameters. The permutation entropies are obviously different in the intrinsic mode functions with the highest energy, thus, the permutation entropy of the intrinsic mode function with the highest energy is regarded as a new characteristic parameter to extract the feature of ship radiated noise. After that, the characteristic parameters, namely, the energy difference between high and low frequency, permutation entropy, and multi-scale permutation entropy, are compared with the permutation entropy of the intrinsic mode function with the highest energy. It is discovered that the four characteristic parameters are at the same level for similar ships, however, there are differences in the parameters for different types of ships. The results demonstrate that the permutation entropy of the intrinsic mode function with the highest energy is better in separability as the characteristic parameter than the other three parameters by comparing their fluctuation ranges and the average values of the four characteristic parameters. Hence, the feature of ship radiated noise can be extracted efficiently with the method.

In order to overcome the limitation of the traditional adaptive Unscented Kalman Filtering (UKF) algorithm in noise covariance estimation for statement and measurement, we propose a hybrid adaptive UKF algorithm based on combining Maximum a posteriori (MAP) criterion and Maximum likelihood (ML) criterion, in this paper. First, to prevent the actual noise covariance deviating from the true value which can lead to the state estimation error and arouse the filtering divergence, a real-time covariance matrices estimation algorithm based on hybrid MAP and ML is proposed for obtaining the statement and measurement noises covariance, respectively; and then, a balance equation the two kinds of covariance matrix is structured in this proposed to minimize the statement estimation error. Compared with the UFK based MAP and based ML, the proposed algorithm provides better convergence and stability.

Microcystis aeruginosa is a common cyanobacteria found in water blooms and often causes ecological harm. Antibiotics are also increasingly used for the prevention and treatment of bacterial infections in aquaculture. However, since most antibiotics cannot be fully metabolized, they enter the water environment and cause ecological impacts. In this paper, the effects of the two quinolone antibiotics (enrofloxacin and ciprofloxacin) on the population density and microcystins (MCs) production of Microcystis aeruginosa were studied. It is of great significance for the ecological risk assessment of antibiotics to the water environment. The results showed that the 96h EC50 values of enrofloxacin and ciprofloxacin to Microcystis aeruginosa were 56.10mg/L and 49.80mg/L respectively, and the toxicity of ciprofloxacin to Microcystis aeruginosa was slightly stronger than that of enrofloxacin. With the increase of the two quinolone antibiotic concentration, the growth inhibition rate (IR) increased, but when the concentration reached a certain height, the IR would reach its threshold. Long-term exposure to low concentrations of these two quinolone antibiotics is not only more likely to lead to the outbreak of Microcystis aeruginosa, but also increase its toxin production capacity. The highest contents of MCs in enrofloxacin and ciprofloxacin groups were 95.539 μg/g and 93.720 μg/g, respectively. The MCs value of these three enrofloxacin treatment groups was more than above 51.8 times that of control group (CK) on the 4th day; from 8th day to 14th day, the MCs value of these three enrofloxacin treatment groups was more than above 3.2 times that of CK group. For another ciprofloxacin, the MCs value of the treatment group was more than 64.98 times that of the CK group on the 4th day, and from 8th day to 14th day, the MCs value of the treatment group was more than 2.7 times that of the CK group. These findings provide crucial management rationale.

With the rapid development of satellite remote sensing technology, the volume of image datasets in many application areas is growing exponentially and the demand for Land-Cover and Land-Use change remote sensing data is growing rapidly. It is thus becoming hard to efficiently and intelligently retrieve the change information that users need from massive image databases. In this paper, content-based image retrieval is successfully applied to change detection and a content-based remote sensing image change information retrieval model is introduced. First, the construction of a new model framework for change information retrieval in a remote sensing database is described. Then, as the target content cannot be expressed by one kind of feature alone, a multiple-feature integrated retrieval model is proposed. Thirdly, an experimental prototype system that was set up to demonstrate the validity and practicability of the model is described. The proposed model is a new method of acquiring change detection information from remote sensing imagery and so can reduce the need for image pre-processing, deal with problems related toseasonal changes as well as other problems encountered in the field of change detection. Meanwhile, the new model has important implications for improving remote sensing image management and autonomous information retrieval.

Polysaccharide from Ficus carica L. (FCP) exert multiple biological activities, as a biological macromolecule, the available knowledge about the specific structures and mechanisms of biological activity of purified 'Brunswick' fig polysaccharide is currently limited. In the present study, by chemical purification and characteristics identified via specific instruments, and then the impact of FCP on the immunomodulation activity in vitro and in vivo was examined. Structural char-acteristics showed that the molecular weight of the FCP was determined to be 127.5 kDa, the primary monosaccharides present in the FCP were galacturonic acid (GalA), arabinose (Ara), galactose (Gal), rhamnose (Rha), glucose (Glc), and xylose (Xyl) at a ratio of 0.321:0.287:0.269:0.091:0.013:0.011. Based on the investigation of in vitro immunomodulatory ac-tivity, FCP was found to stimulate the production of NO, TNF-α, and IL-6 and increased the pi-nocytic activity of macrophages. Further analysis revealed that FCP activated macrophages by interacting with toll-like receptor 4 (TLR4). Moreover, the in vivo test results indicate that FCP showed significant increase serum pro-inflammatory factors in immunosuppressed mice. Overall, this study suggests that FCP has the potential to be utilized as a novel immunomodulator in the pharmaceutical and functional food industries.

Cancer is a common illness with a high mortality. Compared to traditional technologies, biomarkers detection, with low cost and simple operation, has higher sensitivity and faster speed in early screening and prognosis of cancer. Therefore, extensive research has been focused on the development of biosensors and the construction of sensing interfaces. Molybdenum disulfide (MoS2) is a promising two-dimensional (2D) nanomaterial, whose unique adjustable bandgap shows excellent electronic and optical properties in the construction of biosensor interfaces. It not only has the advantages of high catalytic activity and low manufacturing costs, but also can further expand the application of hybrid structures by different functionalization, and is widely used in various biosensors fields. Herein, the application of electrochemical and optical sensing platforms based on MoS2 in the detection of cancer biomarkers was comprehensively reviewed. Firstly, the structure and preparation method of MoS2 were introduced, and its applicable characteristics in the field of biosensors were explored. Secondly, we comprehensively reviewed the recent construction and application of sensing platform based on MoS2 in the field of cancer biomarkers detection in both electrochemical and optical aspects. The prime characteristics and application performances of MoS2 and its composites were emphasized. Additionally, we also involved some other types of biosensors based on MoS2. Finally, we summarized the challenges and development prospects of MoS2 in the application of cancer biomarkers detection, and provided some insights for the application potential of this kind of emerging nano-materials in a broader field.

In typical Cobalt-chromium (CoCr) alloys powders, aluminum oxide (Al₂O₃) powder can be added. In the present study, we successfully prepared alloyed samples of various powder ratios by laser cladding, and analyzed their microstructure and carbide structural characteristics, including microhardness, biological properties, morphology (using scanning electron microscopy), and crystal structure (using X-ray powder diffraction). Elemental distribution was also determined by energy-dispersive X-ray spectral analysis. The results showed that Al₂O₃ addition caused the alloy to change from slender columnar crystals to columnar grains similar, to equiaxed grains. In addition, Al₂O₃ agglomeration zones appeared, and carbide structures were altered. The mechanism of the observed performance changes was also analyzed.

In high-risk railway construction, personal protective equipment monitoring is critical but challenging due to small and frequently obstructed targets. We propose YOLO-EA, an innovative model that enhances safety measure detection by integrating ECA into its backbone's convolutional layers, improving discernment of minuscule objects like hardhats. YOLO-EA further refines target recognition under occlusion by replacing GIoU with EIoU loss. YOLO-EA's effectiveness was empirically substantiated using a dataset derived from real-world railway construction site surveillance footage. It outperforms YOLOv5, achieving 98.9% precision and 94.7% recall, up 2.5% and 0.5% respectively, while maintaining real-time performance at 70.774 fps. This highly efficient and precise YOLO-EA holds great promise for practical application in intricate construction scenarios, enforcing stringent safety compliance during complex railway construction projects.

This paper studies an effective finite difference scheme for solving two-dimensional Heston stochastic volatility option pricing model problems. A dynamically balanced up-downwind strategy for approximating the cross-derivative is implemented and analyzed. Semi-discretized and spatially nonuniform platforms are utilized. The numerical method comprised is simple, straightforward with reliable first order overall approximations. The spectral norm is used throughout the investigation and numerical stability is proven. Simulation experiments are given to illustrate our results.

In this research article we solve the problem of synchronization and anti-synchronization of chaotic systems described by discrete and time-delayed variable fractional order differential equations. To guarantee the synchronization and anti-synchronization of these systems, we use the well-known PID control theory and the Lyapunov-Krasovskii stability theory for discrete systems of variable fractional order.We illustrate the results obtained through simulation with examples, in which it can be seen that our results are satisfactory, thus achieving synchronization and anti-synchronization of chaotic systems of variable fractional order with discrete time delay.

End-to-end learned image compression codecs have notably emerged in recent years. These codecs have demonstrated superiority over conventional methods, showcasing remarkable flexibility and adaptability across diverse data domains while supporting new distortion losses. Despite challenges such as computational complexity, learned image compression methods inherently align with learning-based data processing and analytic pipelines due to their well-suited internal representations. The concept of Video Coding for Machines has garnered significant attention from both academic researchers and industry practitioners. This concept reflects the growing need to integrate data compression with computer vision applications. In light of these developments, we present a comprehensive survey and review of lossy image compression methods. Additionally, we provide a concise overview of two prominent international standards, MPEG Video Coding for Machines and JPEG AI. These standards are designed to bridge the gap between data compression and computer vision, catering to practical industry use cases.

Incident rates of neurodegenerative diseases have steadily increased globally, but there is no therapeutic access available. We newly prescribed medicinal herbal remedy including five different herbal plants called, Chen-Ma-Dan-Sam-Ga-Mi-Bang (CMST), purposed to prove for pharmacological properties and corresponded actions on hippocampus neuronal cell injury by hypoxia-induced mice model. Mice were adapted to normoxia or hypoxia with or without CMST for 5 days. We gathered pharmacological effects of CMST on cell injury by enhancement of dihydroethidium and 4-hydroxynonenal signals which were correlated with abnormal redox status in the protein or gene expression levels (abnormal elevations of nitric oxide, reactive oxygen species, lipid peroxidation and deteriorations of total glutathione, total antioxidant capacity, and activities of superoxide dismutase and catalase) due to hypoxia. CMST also notably exerted to attenuates molecules for neuronal cell injury markers such as p-tau, cleaved caspase-3 due to DNA oxidations (53bp1and phosphor-histone H2AX), inflammatory cytokines, and hemeoxigenase-1. We further figured out the underlying actions of CMST by in vitro experiment through inactivation of microglial cell which can mediate neuronal cell injury. Collectively, CMST prevented from hippocampal neuronal cells via inactivation of microglial cell with normalization of redox status on hypoxia-induced hippocampus neuronal cell injury.

With the rapid development of society and the deteriorating natural environment, there has been an increase in public events. This study aimed to explore how sadness and fear in the context of public emergency influence moral judgments. This research first induced feelings of sadness and fear by videos about public events and music, and then used moral scenarios from the CNI model to assess participants’ moral thinking. In Study 1, participants were divided into sadness group and neutral group, while in Study 2, participants were divided into fear group and neutral group. During the experiment, participants were exposed to different videos related to public events to induce the corresponding emotions, and emotional music was continuously played throughout the entire experiment. Participants were then asked to answer questions regarding moral judgments. The results showed that based on CNI model, sadness induced in the context of public events significantly increased C parameter, without affecting N or I parameter. Fear increased I parameter, without affecting C or I parameter. That is, sadness and fear induced in the context of public events can influence moral judgments. Specifically, sadness increases individuals’ sensitivity to consequence, and fear increases the general preference for inaction in moral judgments.

For personalized recommender systems,matrix factorization and its variants have become mainstream in collaborative filtering.However,the dot product in matrix factorization does not satisfy the triangle inequality and therefore fails to capture fine-grained information. Metric learning-based models have been shown to be better at capturing fine-grained information than matrix factorization. Nevertheless,most of these models only focus on rating data and social information, which are not sufficient for dealing with the challenges of data sparsity. In this paper,we propose a metric learning-based social recommendation model called SRMC.SRMC exploits users' co-occurrence pattern to discover their potentially similar or dissimilar users with symmetric relationships and change their relative positions to achieve better recommendations.Experiments on three public datasets show that our model is more effective than the compared models.

The branch prediction units (BPUs) generally have security vulnerabilities, which can be used by attackers to obtain the execution status, jump directions, and jump address of conditional branches, and the existing protection methods cannot defend against these attacks. Therefore, this article proposes a hardware security protection method for conditional branches of embedded systems. This method calculates the number of updates to the branch target buffer (BTB). When it exceeds the threshold, BTB is locked to prevent attackers from analyzing the execution status of branches based on the time difference of whether BTB is updated. Moreover, the hybrid physical unclonable function (PUF) circuit is designed to provide confidentiality protection for the jump directions, jump addresses, and their indexes, preventing attackers from stealing these critical data. If these mechanism fails and attackers successfully tamper with conditional branches, this paper proposes a control flow integrity (CFI) protection mechanism based on branch labels to timely detect tampering with instruction codes, jump addresses, and jump directions. The proposed method is implemented and tested on FPGA. The experimental results show that this method can achieve fine-grained security protection for conditional branches, with about 5.4% resource overhead and less than 5.5% performance overhead.

The wellness economy has developed rapidly recently, particularly in wellness tourism. Wellness tourism transforms sustainable strategy through the availability of extended multi-actor engagement in service innovation to further the tourism experience. Therefore, when operating a wellness tourism destination, it is necessary to encourage multi-actor engagement in service innovation to achieve sustainable development. This paper introduces a mixed research method with the SWOT-AHP-QSPM, as it qualitatively analyzes the advantages, disadvantages, opportunities, and threats, constructs an evaluation index system, conducts quantitative analysis using the analytic hierarchy process, determines the index weight and weighted score, and calculate the sustainable development strategy, which is appropriate for wellness development of Chongqing Tea Mountain and Bamboo Forest National Forest Park. Purposive field surveys and personal interviews were conducted in Chongqing forest tourism destinations, involving 356 effective respondents. The research reveals that multi-actor engagement significantly enhances sustainable development. These findings bridge service innovation knowledge gaps and provide valuable insights for forest tourism destination management and sustainable policy strategies to elevate multi-actor engagement in forest sites.

Classifying network flow subsequences in an Industrial IoT gateway is an effective method for identifying Industrial IoT faults. This paper proposes a subsequence classification algorithm SSGBUL-IKNN based on unsupervised learning encoding to address the problem of low classification accuracy. Firstly, we built a network module based on unsupervised learning to encode the flow sequence of the Industrial IoT gateway. In the encoding module, a subsequence calibration algorithm controls the increasing error during the coding process. Then, the specific fault type is obtained through an improved KNN classification algorithm based on the indication distance source from the integrated coding sequences converted by multi-dimensional network flow sequences. The test result on three Industrial IoT datasets of a sewage treatment plant shows that the accuracy of SSGBUL-IKNN in this paper exceeds 92%, significantly higher than the algorithm DTW and TSF. It reaches the classification requirements of Industrial IoT fault diagnosis.

In this paper, we study the global existence and exponential decay for a dynamic contact problem between a Timoshenko beam with second sound and two rigid obstacles, of which the heat flux is given by Cattaneo's law instead of the usual Fourier's law. The main difficulties arise from the irregular boundary terms, from the low regularity of the weak solution and from the weaker dissipative effects of heat conduction induced by Cattaneo's law. By considering related penalized problems, proving some a priori estimates and passing to the limit, we prove the global existence of the solutions. By considering the approximate framework, constructing some new functionals and applying the perturbed energy method, we obtain the exponential decay result for the approximate solution, and then prove the exponential decay rate to the original problem by utilizing the weak lower semicontinuity arguments.

The COVID-19 pandemic resulted in government restrictions that altered the lifestyle of people worldwide. Studying the impact of these restrictions on exercise behaviors will improve our understanding of environmental factors that influence individuals’ PA. We conducted a retrospective analysis using an index of government pandemic stringency developed by Oxford and a wearable device for runners to compare strictness of lockdowns and exercise habits, using digitally-logged PA data from more than 7,000 runners on a global scale. Additionally, time-of-day of PA globally and levels of PA in 14 countries are compared between the pre-pandemic year of 2019 and the first pandemic year of 2020. We found that during the pandemic the time-of-day that people exercised experienced a major shift, with significantly more activities logged during standard working hours on workdays (p<0.001) and fewer during the same time frame on weekends (p<0.001). Of the countries examined, Italy and Spain had among the most strict lockdowns and suffered the largest decreases in activity counts, whereas France experienced a minimal decrease in activity counts despite enacting a similarly strict lockdown. This study suggests that there are several factors affecting PA, including government policy, workplace policy, and cultural norms.

Natural vegetation restoration has become an effective and rapid way for eco-logical restoration in fragile areas. However, the response of soil microorgan-isms remains unclear. Using high-throughput sequencing methods, we evalu-ated the dynamics of soil bacterial and fungal communities during forest suc-cession (shrubland, secondary forest, and primary forest) in the karst region of Southwest China. Secondary forest had significantly higher bacterial α-diversity than the shrubland and primary forest. Soil bacterial community in the primary forest was close to the shrubland but diverged from the secondary forest, and that the fungal community could be discriminated along forest suc-cession. Also, the microbial co-occurrence network indicated that soil fungi had less but more intense relationships than bacteria in the karst forests. Further-more, soil properties (pH, SOC, TN, moisture, and AK), soil microbial biomass (MBP, and MBN), and plant factors (Shannon index of woody plants) drove the dynamics of the soil bacterial community, while soil properties (i.e., pH) mostly explained the variation of the soil fungal community along karst forest succession. Different responses of soil bacteria and fungi to forest succession in a karst region give hints for ecological restoration along forest succession in the karst region.

In the paper, by the Faά di Bruno formula, several identities for the Bell polynomials of the second kind, and an inversion theorem, the authors simplify coefficients of two families of nonlinear ordinary differential equations for the generating function of the Catalan numbers and discover inverses of fifteen closely related lower triangular integer matrices.

Evidence indicates that the long noncoding RNAs are involved in the metformin-mediated anti-cancer processes. However, the potential effects of the long noncoding RNAs in metformin-mediated anti-tumor processes in esophageal squamous cell carcinomas (ESCC) are still elusive. This study uncovered that metformin decreases the level of long noncoding RNAs CCAT1 and SPRY4-IT1 thereby contributing to the down-regulation of c-Myc and vimentin. Also, the RNA level test of human ESCC tissue confirmed the positive correlation between CCAT1 and c-Myc. These findings demonstrated that metformin facilitated anti-cancer effects by targeting the 2 long noncoding RNAs (CCAT1 and SPRY4-IT1) and their consequential targets c-Myc and vimentin. Therefore, the CCAT1 and SPRY4-IT1 might act as novel molecular targets that mediate the anti-tumor effects in esophageal squamous cell carcinoma. This helps in predicting the treatment response of metformin in patients diagnosed with esophageal squamous cell carcinoma.

This study extends the CGAN-based MODIS cloud vertical-profile (64×64-scene, about 70km width×15km height) retrieval technique developed by Leinonen et al. (2019) [1] to construct seamless 3D cloud fields for the MODIS granules [2]. Firstly, the accuracy and spatial continuity of the Leinonen et al. [1] retrievals are statistically evaluated. Then, according to the characteristics of the retrieval error, a spatially overlapping-scene ensemble generation method and a bi-directional Ensemble Binning Probability Fusion (CGAN-BEBPF) technique are developed, which improves the CGAN retrieval accuracy and support to construct seamless 3D clouds. The CGAN-BEBPF technique involves three steps: cloud masking, intensity scaling, and optimal value selection. It ensures adequate coverage of the low reflectivity areas while preserving the high reflectivity cloud cores. The technique is applied to retrieve the 3D cloud fields of Typhoon Chaba and a multi-cell convective system. The cloud structures of the CGAN-BEBPF results are highly consistent with the ground-based radar observations. It can retrieve weak clouds at the top levels of convective storms and hurricanes that were missed by ground-based radars and fill the gaps of the ground-based radar lower-level PPI scan. Overall, CGAN-BEBPF can be automated to retrieve the rich informative 3D structures of typhoons and severe convective systems over the oceans along the MODIS swath, which certainly presents great value for improving maritime and near-shore typhoons and convection prediction and other cloud-sensitive applications.

The monitoring of lake waterbody area in the Qinghai Tibet Plateau (QTP) is of great significance to deal with global climate change. As the latest generation of Landsat series satellites, Landsat-9 data not only have higher radiometric resolution, but also cooperate with other Landsat satellites to greatly improve the temporal resolution. It has great application potential in lake waterbody area monitoring. In order to explore the performance of different algorithms for extracting waterbody and lake waterbody area in Landsat-9 data under large-scale QTP regions, this study relies on Google Earth Engine (GEE) platform and selects 10 waterbody extraction algorithms as the basis to realize the quantitative evaluation of QTP lake waterbody area extraction results. The results show that the Random Forest (RF) algorithm performs best in all models. The overall accuracy of waterbody extraction is 95.84%, and the average error of lake waterbody area extraction is 1.505%. Among the traditional threshold segmentation waterbody extraction algorithms, the overall accuracy of the NDWI waterbody extraction method is 89.89%, and the average error of lake waterbody area extraction is 3.501%, which is the highest performance model in this kind of algorithms. This study proves that Landsat-9 data can effectively classify QTP waterbodies. With the development of cloud computing technologies such as Gee, more complex models such as RF can be selected to improve the extraction accuracy of water body and Lake area in large-scale research.

In order to achieve better knowledge of the thermal barrier coatings (TBCs) by supersonic atmospheric plasma spraying (SAPS) process, an experimental study was carried out to elaborate physicochemical properties of particles in-flight during the SAPS process. One type of commercially available agglomerated and sintered yttria-stabilized-zirconia (YSZ) powders were injected into the SAPS plasma jet and collected by shock chilling method. The YSZ particles in-flight physicochemical properties of the melting state, morphology, microstructure, particle size distribution, element composition changes and phase transformation during the SAPS process have been systematically analyzed. The melting state, morphology and microstructure of the collected particles were determined by scanning electron microscopy (SEM). The particle size distribution was measured by a laser particle size analyzer (LPSA). Element compositions were quantitatively analysed by an electron probe X-ray microanalyzer (EPMA). Additionally, the X-ray diffraction (XRD) method was used to analyse the phase transformation. The results showed that the original YSZ powders injected into the SAPS plasma jet were quickly heated and melted from the outer layer companied with breakup and collision-coalescence. The outer layer of the collected particles containing roughly hexagonal shaped grains exhibited a surface texture with high sphericity and the inside was dense with hollow structure. The median particle size was decreased from 45.65 μm to 42.04 μm. Besides, phase transformation took place and the content of zirconium (Zr) and yttrium (Y) element was decreased with the evaporation of ZrO2 and Y2O3.

Clustered regularly interspaced short palindromic repeats/associated protein 9 nuclease (CRISPR/Cas9) technology guided by a single-guide RNA (sgRNA) has recently opened a new avenue for antiviral therapy. A unique capability of the CRISPR/Cas9 system is multiple genome engineering. However, there are few applications in insect viruses by a single Cas9 enzyme targeting two or more sgRNA at different genomic sites for simultaneous production of multiple DNA breaks. To address the need for multi-gene editing and sustained delivery of multiplex CRISPR/Cas9-based genome engineering tools, we developed a one-vector (pSL1180-Cas9-U6-sgRNA) system to express multiple sgRNA and Cas9 protein to excise Bombyx mori nucleopolyhedrovirus (BmNPV) in insect cells. Here, ie-1, gp64, lef-11, and dnapol genes were screened and identified as multiple sgRNA editing sites according to the BmNPV system infection and DNA replication mechanism. Furthermore, we constructed a multiplex editing vector sgMultiple to efficiently regulate multiplex gene editing steps and inhibit BmNPV replication after viral infection. This is the first report that describes the application of multiplex CRISPR/Cas9 system inhibiting insect virus replication. This multiplex system can significant enable the potential of CRISPR/Cas9-based multiplex genome engineering in transgenic silkworms.

Anti-interferon (IFN)-γ autoantibodies are linked to varicella-zoster virus (VZV) infection. Given the elevated risks of herpes zoster (HZ) in rheumatoid arthritis (RA) patients treated with Janus kinase inhibitors (JAKi), we aimed to examine the relationship between anti-IFN-γ autoantibodies with HZ development in JAKi-treated patients. In twenty-four RA patients with new-onset HZ and forty-two without HZ, serum titers of anti-IFN-γ autoantibodies, plasma levels of IFN-γ, monocyte chemoattractant protein-1 (MCP-1), and IFN-γ inducible protein-10 (IP-10) were measured by ELISA. Significantly lower MCP-1 levels were observed in patients with HZ compared to those without (median, 98.21pg/ml, interquartile range (IQR) 77.63-150.30pg/ml versus 142.3pg/ml, IQR 106.7-175.6pg/ml, p&lt;0.05). There was no significant difference in anti-IFN-γ titers, IFN-γ levels, or IP-10 levels between patients with and without HZ. Three of 24 patients with HZ had severe HZ with multi-dermatomal involvement. Anti-IFN-γ titers were significantly higher in patients with severe HZ than in those with non-severe HZ (median 24.8ng/ml, IQR 21.0-38.2ng/ml versus 10.5ng/ml, IQR 9.9-15.0ng/ml, p&lt;0.005). In conclusion, patients with HZ had significantly lower MCP-1 levels than those without HZ, and patients with severe HZ had significantly higher titers of anti-IFN-γ than those with non-severe HZ. Given small sample size, our results need further validation in future studies.

Reactive NO_x is one of the major air pollutants, which also plays a key role as greenhouse gas. Many research efforts have been devoted to not only detection of NO_x in air but also abatement of NO_x emission. The aim of this mini review is to provide a panoramic snapshot of the electrochemical analysis methods for the emission and detection of NO_x in atmosphere, with special emphasis on NO_x sensor. The electrochemical detecting mechanism and materials for fabricating electrochemical gas sensors are discussed and the prospects and challenges in this area are also evaluated. This work will serve as a useful source to inform the interested audience of the latest developments and applications in the field of NO_x emission and electrochemical detection.

The time’s arrow of macroscopic physical phenomenon is reflected by irreversible physical process, which essentially occurs from small probability state to high probability state. In this paper, simplified models are proposed to understand the macroscopic physical process. In order to describe the information of a physical system, we defined the full self-information as "information height" to describe the complexity or difficulty of a macrostate of physical system. In this way, the direction of macroscopic physical process is from high information height to low information height. We can judge the direction of physical process by the information height. If we want the macroscopic physical process to evolve from the low information height state to the high information height state, the system need to add extra information and corresponding energy to increase the information height.

Proton exchange membrane water electrolyzers (PEMWEs) for water electrolysis have received tremendous attention due to their immediate response, high proton conductivity, low ohmic losses and gas crossover rate. However, design high activity, economical and long-term durable electrocatalysts in an acidic environment is still the bottleneck to realize the large-scale commercialization of PEMWEs. Iridium-based materials represent one of the most promising classes of oxygen evolution reaction (OER) catalysts due to their intrinsic stability in acid media over ruthenium-based counterparts. However, only a few innovative approaches have been developed to synthesizing iridium-based catalysts (IBCs) in the past decade, mainly due to achieving high activity may deteriorate the stability of IBCs. Accordingly, various engineering strategies of optimizing IBCs have been proposed to address this issue, including doping engineering, morphology engineering, crystal phase engineering and support engineering. Herein, a critical overview focusing on various synthesis and modulation strategies of IBCs is presented, based on an in-depth understanding of the relationship between electronic structures, charge redistribution and activity as well as stability of the electrocatalysts. In addition, the unprecedented achievements in PEMWEs are summarized. The reaction mechanisms and future perspectives are critically discussed to inspire more rational design of IBCs toward practical applications.

Mangrove plant seedling cultivation is crucial for the protection, management and restoration of mangrove ecosystem. In this study, we focused on Kandelia obovata, a typical mangrove, and evaluated nursery cultivation with different combinations of three salinity levels (S1: 0 ppt, S2: 10 ppt, and S3: 20 ppt), three genealogies (EZD, JX, and YZ), and five growth media (M1: 100% loess, M2: 100% sandy, M3: 50% loess + 50% sandy, M4: 40% loess + 40% sandy + 20% peat, and M5: 40% loess + 40% sandy + 20% coir), by measuring the growth parameters such as mortality rate, seedling height, diameter, and biomass partition. These growth indexes were significantly affected by salinity and medium, and genealogies also had significant effects on mortality rate and biomass accumulation. S2 or S3 both had lower mortality and higher growth indexes than S1. M1 was the medium that increased seedlings height, diameter and biomass the most and had the lowest death rate. EZD and JX were also higher levels than YZ in these indicators, but the difference between them was not obvious. S3, M1, and EZD consistently performed well in fuzzy evaluation and quality assessment. Furthermore, combinations involving these treatments also produced highly favorable results. These results furnish both a theoretical and practical foundation for advancing nursery cultivation techniques and germplasm breeding of K. obovata in mangroves.

To promote low-carbon and green travel, this study proposes a tripartite evolutionary game model among new energy vehicle manufacturers, consumers, and government agencies. The game strategy combinations of each party and the stability conditions of the equilibrium point in the evolutionary game system are analyzed, and the validity of the conclusions is verified through simulation results. The study shows a strong correlation between the three parties in the evolutionary game system. From the perspective of car manufacturers, the probability of producing new energy vehicles is positively proportional to the subsidy received from new energy policy, the additional revenue gained from the management of the carbon trading scheme, and the fine received for producing conventional fuel vehicles. However, from the consumer perspective, the likelihood that consumers purchase new energy vehicles is positively related to the utility value to consumers and the coverage of public charging points in the city, and inversely related to the sales price of new energy vehicles. From the government perspective, a combination of direct subsidy policies and indirect support strategies should be considered to stimulate the rapid development of the new energy vehicle industry.

Road cracks significantly affect the serviceability and safety of roadways, especially in mountainous terrain. Traditional inspection methods, such as manual detection, are excessively time-consuming, labor-intensive, and inefficient. Additionally, multi-function detection vehicles equipped with various sensors are expensive and not suitable for mountainous roads due to poor conditions. To address these challenges, this study proposes a customized Unmanned Aerial Vehicles (UAV) inspection system designed for automatic crack detection. The system focuses on enhancing autonomous capabilities in mountainous terrains by incorporating embedded algorithms for route planning, autonomous navigation, and automatic crack detection. The slide window method is proposed to enhance the autonomous navigation of UAV flights by generating path planning in mountainous roads. This method compensates for GPS/IMU positioning errors, particularly in GPS-denied or GPS-drift scenarios. Moreover, the YOLOv8 algorithm is introduced to conduct autonomous crack detection from UAV imagery in the offboard module. To validate our UAV inspection system's performance, we conducted several experiments to assess its accuracy, robustness, and efficiency. The experimental results demonstrate that our UAS inspection system accurately estimates the flight trajectory along the mountainous road for autonomous navigation. Furthermore, the experimental detection results also demonstrate that the YOLOv8 algorithm achieves higher recognition accuracy compared to the YOLOv5, and YOLOv7-tiny algorithms, exceeding 3.1%,and 6.8% of mAP, respectively. In summary, the UAV inspection system proposed in this study can provide a useful tool and technological guidance for the regular inspection of mountainous roads.

Parallax processing and structure preservation has long been important and challenging tasks in image stitching. In this paper, an image stitching method based on sliding camera to eliminate perspective deformation and asymmetric optical flow to solve parallax is proposed. By maintaining the viewpoint of two input images in the mosaic non-overlapping area and creating a virtual camera by interpolation in the overlapping area, the viewpoint is gradually transformed from one to another image view-point so as to complete the smooth transition of the two image viewpoints and reduce perspective deformation. Two coarsely aligned warped images are generated with the help of a global projection plane. After that, the optical flow propagation and gradient descent method are used to quickly calculate the bidirectional asymmetric optical flow between the two warped images, and the optical flow-based method is used to further align the two warped images to reduce parallax. In the image blending, the softmax function and registration error are used to adjust the width of the blending area, further eliminating ghosting and reduce parallax. Finally, the comparative experiments show that our method can effectively eliminate perspective deformation, reduce misalignment, and save running time.

To estimate the progressive collapse resistance capacity of a multi-column frame tube structure with the assembled truss beam composite floor (ATBCF), the pushdown analysis, and the nonlinear dynamic analysis as well, are conducted for such a structure by using the alternate load path (ALP) method. The bearing capacities of the remaining structures at three different work conditions, which are the side middle column failure, the edge middle column failure, and the corner column failure, are individually studied, and the collapse mechanism for the remaining structures is analyzed from the aspects of the internal force redistribution and the failure mode of the second defense line. Simultaneously, the influence of the column failure time on the dynamic response of the remaining structure and the dynamic amplification coefficient are discussed. The results show that the residual bearing capacity of the remaining structure with the bottom corner column failure is higher than that of the one with the side or edge middle column failure, while the latter has a stronger plastic deformation capacity. When the ALP method is adopted to operate the progressive collapse analysis, it is reasonable to take the column failure time as 0.1 times of the first-order vertical vibration period of the remaining structure, and it is suitable to set the dynamic amplification coefficient as of 2.0, which is the ratio of the maximum dynamic displacement to the static displacement of the remaining structure under the transient loading condition.

Sulfate attack is one of the main factors affecting the durability of concrete structures. In recent years, multi-walled carbon nanotubes (MWCNTs) have attracted the attention of scholars for their excellent mechanical properties and durability performance. In this paper, the influence of sulfate attack and dry-wet cycles on the performance of multi-walled carbon nanotube-lithium slag concrete (MWCNTs-LSC) with varied MWCNTs content (0wt%, 0.05wt%, 0.10wt% and 0.15wt%) and varied water-cement ratios (0.35, 0.40 and 0.45) were investigated. Besides, scanning electron microscopy (SEM) and X-ray computed tomography (CT) tests were conducted to analyze the microstructure and pore structure of the concrete. The results show that concrete incorporated with MWCNTs could effectively mitigate sulfate attack The resistance to sulfate attack of concrete is negatively related to the water-cement ratio when the dry-wet cycle is fixed. The MWCNTs-LSC showed the best compressive strength at the water-cement ratio of 0.35 and 0.10 wt% MWCNTs. The SEM test results showed that the MWCNTs both filled the pores and cracks within the specimen and formed bridges between the cracks, enhancing the resistance to sulfate attack. The CT test results also showed that the addition of MWCNTs could reduce the porosity of concrete, refine the pore size and inhibit the generation and development of cracks, thus optimizing the internal structure of concrete and improving its resistance to sulfate attack.

The rock joint fissure slope in cold regions is prone to deformation and failure problems such as relaxation, tension and collapse under freeze-thaw (F-T) cycles. Based on the ideology of clean production and promoting the structural integrity of geotechnical projects in cold areas, this study designed and prepared aeolian-sand (AS) to replace part of river sand as a filling mortar material by taking advantage of the low cost and easy availability of AS. Investigations were carried out to determine the impact of varying proportions of AS in mortar on the microstructure and shear properties of the mortar-rock interface under F-T cycles. Therefore, F-T cycle testing, nuclear magnetic resonance (NMR) testing and shear testing were carried out on grout with different proportions of AS. The results show that the right proportion of AS replacement could enhance the shear deformation resistance and F-T resistance of the mortar-rock interface, and 30% proportion is the optimal proportion. By increasing of F-T cycles, the three types of specimens showed different degrees of particle spalling, shedding and cracking. The slurry-rock interface layer in the A (0%) group exhibited the most severe F-T deterioration, while the B (15%) group showed a lesser degree, and the C (30%) group performed the best. T2 spectrum curve and total spectrum area change law from the microscopic point of view to verify the 30% AS proportion mortar-rock interface F-T resistance is the strongest, followed by 15% AS proportion mortar, the weakest is ordinary mortar. The degradation of the mortar-rock bond is primarily due to the conversion of solid to liquid phases and the movement of internal water caused by fluctuating temperatures. The extent of F-T deterioration in the slurry-rock interface layer is greatly affected by the varying proportions of AS. The shear strength and shear stiffness of specific proportion of AS decreased with the increase of F-T cycles. For same F-T cycles, the shear strength and shear stiffness of group C (30%) were the highest, followed by group B (15%) and group A (0%). The grout material not only reinforces the F-T joint fissure slope, but also reduces the cost of grout reinforcement and promotes the clean production of geotechnical structures.

Pathogens, especially invasive species, have caused significant global ecological, economic, and social losses in forests. Plant disease research has traditionally focused on direct interactions between plants and pathogens in an appropriate environment. However, recent research indicates that the microbiome can interact with the plant host and pathogens to modulate plant resistance or pathogen pathogenicity, thereby altering the outcome of plant–pathogen interactions. Thus, this presents new opportunities for studying the microbial management of forest diseases. Compared to parallel studies on human and crop microbiomes, research into the forest tree microbiome and its critical role in forest disease progression has lagged. The rapid development of microbiome sequencing and analysis technologies has resulted in the rapid accumulation of a large body of evidence regarding the association between forest microbiomes and diseases. These data will aid the development of innovative, effective, and environmentally sustainable methods for the microbial management of forest diseases. Herein, we summarize the most recent findings on the dynamic structure and composition of forest tree microbiomes in belowground and aboveground plant tissues (i.e., rhizosphere, endosphere, and phyllosphere), as well as their pleiotropic impact on plant immunity and pathogen pathogenicity, highlighting representative examples of biological control agents used to modulate relevant tree microbiomes. Lastly, we discuss the potential application of forest tree microbiomes in disease control as well as their future prospects and challenges.

The high-speed railway operation environment monitoring network system has a wide variety of sensors and inconsistent business requirements, which have certain requirements for data transmission delay and network life. Most of the previous research focuses only on prolonging network lifetime or reducing data transmission delays when designing or optimizing routing protocols, without co-designing the two. In addition, due to the harsh operating environment of high-speed railways, when the network changes dynamically, the traditional routing algorithm will generate unnecessary redesigns and lead to high overhead. Based on the actual needs of high-speed railway operation environment monitoring, this paper proposes a novel Double Q-values adaptive model combined with the existing reinforcement learning method, which considers the energy balance of the network and real-time data transmission, and constructs energy saving and delay. The two-dimensional reward avoids the extra overhead of maintaining a global routing table while capturing network dynamics. In addition, the adaptive weight coefficient is used to ensure the adaptability of the model to each business of the high-speed railway operation environment monitoring system. Finally, simulations and performance evaluations are carried out and compared with previous studies.Finally, simulations and performance evaluations are carried out and compared with previous studies. The results show that the proposed routing algorithm successfully extends the network’s life cycle and gets good real-time data performance. It also saves energy and has fewer delays than the other three routing protocols in different situations.

In wireless sensor networks (WSNs), each sensor node can estimate the global parameter from the local data in distributed manner. This paper proposed a robust diffusion estimation algorithm based on minimum error entropy criterion with self-adjusting step-size, which are referred to as diffusion MEE-SAS (DMEE-SAS) algorithm. The DMEE-SAS algorithm has fast speed of convergence and is robust against non-Gaussian noise in the measurements. The detailed performance analysis of the DMEE-SAS algorithm is performed. By combining the DMEE-SAS with diffusion minimum error entropy (DMEE) algorithms, an Improving DMEE-SAS algorithm is proposed, in non-stationary environment where tracking is very important. The Improving DMEE-SAS algorithm can avoid insensitivity of the DMEE-SAS algorithm due to the small effective step-size near the optimal estimator, and obtain a fast convergence speed. Numerical simulations are given to verify the effectiveness and advantages of these proposed algorithms.

A delayed crosslinked polymer gel was developed for indepth water control in mature oilfields. The thermal gelation behavior of nonionic polyacrylamide (NPAM) and PEI was investigated, and sodium citrate (NaCit) was selected as a new retarder to prolong the gelation time. The gelation performance of NPAM/PEI gel system can be adjusted by the variation of NPAM or PEI concentration, and a quadratic model was developed by statistical analysis, which predict the gelation time of NPAM/PEI gel system. The obtained model showed high significance and good reliability as suggested by the F-ratio of 175.16 and high adjusted R-square value (0.9732). The decrease of the initial pH value of gelling solution leads to the weaker gel viscosity and longer gelation time due to the protonation of amine groups on the PEI chains. Increasing temperature resulted in higher gel viscosity but shorter gelation time. The addition of NaCit showed a good delayed gelation effect on the NPAM/PEI gel system, and the gel system in the presence of NaCit exhibited a good compatibility with injected and formation water. A dense three-dimensional structure was observed in matured NPAM/PEI/NaCit gel, and it could keep stable below 150℃. The gel system could effectively reduce the permeability (>95%) and restricted the flow of water after matured in natural cores.