The high-speed railway operation environment monitoring network system has a wide variety of sensors and inconsistent business requirements, which have certain requirements for data transmission delay and network life. Most of the previous research focuses only on prolonging network lifetime or reducing data transmission delays when designing or optimizing routing protocols, without co-designing the two. In addition, due to the harsh operating environment of high-speed railways, when the network changes dynamically, the traditional routing algorithm will generate unnecessary redesigns and lead to high overhead. Based on the actual needs of high-speed railway operation environment monitoring, this paper proposes a novel Double Q-values adaptive model combined with the existing reinforcement learning method, which considers the energy balance of the network and real-time data transmission, and constructs energy saving and delay. The two-dimensional reward avoids the extra overhead of maintaining a global routing table while capturing network dynamics. In addition, the adaptive weight coefficient is used to ensure the adaptability of the model to each business of the high-speed railway operation environment monitoring system. Finally, simulations and performance evaluations are carried out and compared with previous studies.Finally, simulations and performance evaluations are carried out and compared with previous studies. The results show that the proposed routing algorithm successfully extends the network’s life cycle and gets good real-time data performance. It also saves energy and has fewer delays than the other three routing protocols in different situations.

In a global context, the story of the Jesuit compound in Shanghai, since its establishment by French Jesuits in 1847, reflected not only conflicts between rival powers in Europe but also the fight for their interests in the Eastern world. The Pope, who was stuck without legal status in the Vatican after 1861, was also seeking the chance to save the authority of the Church in the face of questions regarding the extent of his temporal power and the status of Rome in the context of Italian unification. As in the Reformation, a break-through in the east seemed to offer a solution for losses in Europe. However, the Jesuits to the East in the late 19th century were not only troops working and fighting on behalf of the Pope; their identities under the French Protectorate added complexity to an already complicated story involving not just the Church, but the course of world history.The female Catholic orders at the east bank of Zi-ka-wei compound became a unique window to approach the complexity.

Mechanism of traffic congestion generation is more than complicated, due to complex geometric road design and complicated driving behavior at urban expressway in China. We employ Cell transmission model (CTM) to simulate traffic flow spatiotemporal evolution process along the expressway, and reveal the characteristics of traffic congestion occurrence and propagation. Here we apply the variable-length-cell CTM to adapt the complicated road geometry and configuration, and propose the merge section CTM considering drivers' mandatory lane-changing and other unreasonable behavior at on-ramp merge section, and propose the diverge section CTM considering queue length end extending expressway mainline to generate dynamic bottleneck at diverge section. In the new improved CTM model, we introduce merge ratio and diverge ratio to describe the effect of driver behavior at merge and diverge section. We conduct simulation on the real urban expressway in China, results show that merge section and diverge section are the original location of expressway traffic congestion generation, on/off-ramp traffic flow has great effect on expressway mainline operation. When on-ramp traffic volume increases by 40%, merge section delay increases by 35%. And when off-ramp capacity increases by 100 veh/hr, diverge section delay decreases about by 10%, which proves the strong interaction between expressway and adjacent road networks . Our results provide the underlying insights of traffic congestion mechanism in urban expressway in China, which can be used to better understand and manage this issue.

Gliomas, the most prevalent and lethal form of brain cancer, are known to exhibit metabolic alterations that facilitate tumor growth, invasion, and resistance to therapies. Peroxisomes, essential organelles responsible for fatty acid oxidation and reactive oxygen species (ROS) homeostasis, rely on the receptor PEX5 for the import of metabolic enzymes into their matrix. However, the prognostic significance of PEX5 for glioma patients remains unclear. We developed a robust prognosis model based on PEX5-dependent signature. This signature not only serves as a robust prognosis model capable of accurately predicting outcomes for glioma patients but also effectively distinguishes several clinicopathological features, including the grade, isocitrate dehydrogenase (IDH) mutation, and 1p19q codeletion status. Furthermore, we developed a nomogram that integrates the prognostic model with other clinicopathological factors, demonstrating highly accurate performance in estimating patient survival. Patients classified into the high-risk group based on our prognostic model exhibit an immunosuppressive microenvironment. Finally, we validated that the peroxisomal localization of the signature genes depends on PEX5 and demonstrated that PEX5 is required for cell growth, migration and invasion of glioma cells. These findings identify the PEX5-dependent signature as a promising prognostic tool for gliomas.

Reactive NO_x is one of the major air pollutants, which also plays a key role as greenhouse gas. Many research efforts have been devoted to not only detection of NO_x in air but also abatement of NO_x emission. The aim of this mini review is to provide a panoramic snapshot of the electrochemical analysis methods for the emission and detection of NO_x in atmosphere, with special emphasis on NO_x sensor. The electrochemical detecting mechanism and materials for fabricating electrochemical gas sensors are discussed and the prospects and challenges in this area are also evaluated. This work will serve as a useful source to inform the interested audience of the latest developments and applications in the field of NO_x emission and electrochemical detection.

Adding a submerged zone (SZ) is deemed to promote denitrification during dry periods and thus improve NO3--N removal efficiency of a bioretention system. However, few studies had investigated the variation of nitrogen concentration in the SZ during dry periods and evaluated the effect of the variation on nitrogen removal of the bioretention system. Based on the experiment in a mesocosm bioretetion system with SZ, this study investigated the variation of nitrogen concentration of the system under 17 consecutive cycles of wet and dry alternation with varied rainfall amount, influent nitrogen concentration and antecedent dry periods (ADP). The results indicated that (1) during the dry periods, NH4+-N concentrations in SZ showed an exponential decline trend, decreasing by 50% in 12.9 ± 7.3 hours; while NO3--N concentrations showed an inverse S-shape decline trend, decreasing by 50% in 18.8 ± 6.4 hours; (2) during the wet periods, NO3--N concentration in the effluent showed an S-shape upward trend; and at the early stage of the wet periods, the concentration was relatively low and significantly correlated with ADP, while the corresponding volume of the effluent was significantly correlated with the SZ depth; (3) in the whole experiment, the contribution of nitrogen decrease in SZ during dry periods to NH4+-N and NO3--N removal accounted for 12% and 92%, respectively; and the decrease of NO3--N in SZ during the dry period was correlated with the influent concentration in the wet period and the length of the dry period.

Human intestinal flora refers to a large and diverse microbial population present in the digestive tract of the human body, which plays a significant role in the establishment of human immune homeostasis and the normal function of the immune system. Myasthenia Gravis is an autoimmune disease of the neuromuscular junction, mainly involved in the anti-acetylcholine receptor antibody, cellular immune dependence, and complement¹. At present, studies have found that the intestinal flora of Myasthenia Gravis is different from that of healthy people. Probiotic therapy has been shown effective in the experimental autoimmune Myasthenia Gravis animal models. This article reviews the relationship between intestinal flora and Myasthenia Gravis, to provide new ideas for further study of the pathogenesis and clinical treatment of Myasthenia Gravis.

Distributed electric propulsion technology has great potential and advantage in the development of drones. In this paper, to study the slipstream effect of distributed propeller, the actuator disk method was used to verify a single propeller, and the calculated thrust was in good agreement with the test results. Then, based on the actuator disk method, the influence of different installation positions on the slipstream effect was studied, and the distributed propeller layout was optimized by genetic algorithm. The analysis results showed that lift of the wing will be larger when the propellers are higher than the wing. When the relative height between the propeller and the wing is zero, the drag is the lowest. The influence of disk diameter on the slipstream is that the larger the diameter is, the higher the lift force and the drag force are. The slipstream effect of the optimized propeller distribution improves the lift-drag ratio of the wing, by 108.5% in the initial lift-drag ratio.

With the rapid development of satellite remote sensing technology, the volume of image datasets in many application areas is growing exponentially and the demand for Land-Cover and Land-Use change remote sensing data is growing rapidly. It is thus becoming hard to efficiently and intelligently retrieve the change information that users need from massive image databases. In this paper, content-based image retrieval is successfully applied to change detection and a content-based remote sensing image change information retrieval model is introduced. First, the construction of a new model framework for change information retrieval in a remote sensing database is described. Then, as the target content cannot be expressed by one kind of feature alone, a multiple-feature integrated retrieval model is proposed. Thirdly, an experimental prototype system that was set up to demonstrate the validity and practicability of the model is described. The proposed model is a new method of acquiring change detection information from remote sensing imagery and so can reduce the need for image pre-processing, deal with problems related toseasonal changes as well as other problems encountered in the field of change detection. Meanwhile, the new model has important implications for improving remote sensing image management and autonomous information retrieval.

Instrumental activities of daily living (IADL) training is critical in clinical practice of occupational therapy (OT) for stroke patients. In the conventional approaches, the therapists simulate various occupational tasks in their healthcare settings or reach their nearby real circumstances for the training. As an alternative technology, immersive virtual reality (IVR) has been used widely in stroke rehabilitation for years; however, limited research has compared occupational performances between virtual and real environments. Our team has established a novel IVR shopping training system for stroke rehabilitation. We recruited 10 stroke patients from our department to test the system. All patients attempted to implement shopping tasks in the virtual and real environments respectively. The Wilcoxon test showed no significant differences between virtual and real environments in memory capacity and time-consuming for implementing tasks, and memory capacities in virtual and real environments presented excellent correlations with the IADL assessment. This study suggests that IVR shopping tasks can be used as an alternative approach in rehabilitation when there is limited resource for implementing shopping training in a real environment, while the psychometric property, clinical effect and the effect transferred to the real environment induced by virtual training require further study.

This paper first explains the theory of the origin of force from a new perspective, explaining that the origin of all forces is caused by the "missing of energy in the time dimension" (non-conservation in a certain period of time), and constructs a unified theory of force on this basis. Then, through the unified theory of force, the following phenomena are reinterpreted: (1) The common origin of the inverse square law of gravitation and electromagnetic force; (2) The origin of the repulsive force of electrons and protons at small distances; (3) The mystery of the rotation curve of galaxies and the new explanation of "dark matter"; (4) explain the origin of the magnetic field; (5) Predict that moving magnets have the same radiation effect as charged particles (electron magnetic moments also have radiation effects); (6) Reinterpret Maxwell's displacement current; (7) Reinterpret synchrotron radiation and bremsstrahlung; (8) Explain that the strong and weak forces are short-range forces; (9) Predict the true structure of black holes and the origin of gravitational waves;(10) Possible explanation for the origin of the speed of light.

Existing evidence suggest that lactoferrin might be beneficial for Alzheimer’s disease. We aimed to determine the effects of lactoferrin intervention on cognitive function from APP/PS1 mice, and possible mechanisms involved in. Both young and middle-aged male APP/PS1 mice were divided into control and lactoferrin group with 16 weeks’ intervention. Lactoferrin intervention had no effects on cognitive function from both young and middle-aged mice, and no key markers involved in Aβ, tau pathology, neuro-inflammation and synaptic plasticity were altered post lactoferrin intervention. In regards to gut microbiota profiles, in the young mice, lactoferrin elevated α diversity index including ACE and Chao 1, and reduced the relative abundance of the genera Bacteroides and Alistipes and elevated Oscillibacter, in addition, Oscillibacter, Anaerotruncus, EF096579_g, EU454405_g, Mollicutes_RF39, EU474361_g, EU774448_g, and EF096976_g were specifically abundant post Lf intervention via LEfSe analysis. In the middle-aged mice, the relative abundance of the phylum Proteobacteria, as well as the genera Oscillospira, Coprococcus and Ruminococcus was significantly reduced post Lf intervention, additionally, S24_7, Bacteroidia, Bacteroidetes and Methylobacterium were specific via LEfSe analysis post lactoferrin intervention. In conclusion, dietary lactoferrin might be beneficial for gut microbiota homeostasis although might have no effects on cognition.

Suitable soil structure and nutrient security are important for plant growth and development, characteristics of soil fractal dimension and distribution of physical and chemical properties and their interactions play an important role in studying the stability of soil structure and water and fertilizer cycles. As a sustainable management model, intercropping has positive benefits for erosion control, spatial optimization of resources, as well as improving system productivity. The effects of four intercropping methods on soil fractal dimension and physicochemical properties were investigated by intercropping Salvia miltiorrhiza with forage and S. miltiorrhiza with forest under typical karst rock desertification habitats in Guizhou. The results showed that soil nutrient content of intercropping was significantly higher than that of monoculture, the organic carbon content of soil grown under forest is higher than other treatments, and there was a non-significant change in soil water content of intercropping compared with monoculture. The soil fine-grained matter of intercropping was significantly higher than that of monoculture, while the soil fractal dimension showed a tendency to become larger with the increase of fine-grained matter. The intercropping planting, due to its component types and spatial and temporal configurations, leads to differences in soil water and fertilizer interactions, which can be combined with other ecological restoration measures to optimize the composite model and jointly promote the restoration and development of ecologically fragile areas.

This paper is another applied article based on the author's "Unified Theory of Force". The main work of this paper is as follows: (1) Reinterpretation of the Lorentz contraction effect and rigorous proof that the Lorentz contraction is a physical phenomenon based on the conservation of energy and momentum under non-completely symmetrical relative motion effects. This paper proves that the Lorentz contraction effect not only occurs in the direction of motion but also simultaneously in any direction. (2) For the first time, we attempted to explain the physical meaning of the Planck energy formula in theory and associate the Planck energy formula with the Lorentz contraction effect, which can help us to have a deeper understanding of the true physical meaning behind the Planck energy formula. At the same time, we also made reasonable theoretical predictions about the basic structure of photons.

There is currently no unified explanation for the origin of Earth's magnetic field, planetary magnetic fields, stellar magnetic fields, and neutron star magnetic fields, and most importantly, none of these theories have been experimentally verified. This paper is based on a new unified theory of mechanics and its derived applications, which may provide a better explanation for the origin of magnetic fields in celestial bodies and can be experimentally tested to better answer the observed phenomena: (1) the greater the mass of the celestial body, the stronger the magnetic field; (2) the faster the rotation speed of the celestial body, the stronger the magnetic field; (3) the higher the density of the celestial body, the stronger the magnetic field produced.

This paper is mainly based on a stricter premise of the twin paradox and the assumption of inertial frame, discusses the properties of time and space under the premise of complete symmetry, and draws an interesting conclusion: the simultaneity of different reference frames is possible realized, and the space is relatively independent. And based on this, the twin paradox, cosmic inflation, ultra-distance action of quantum entanglement, microscopic space motion of particles, measurement problems and other phenomena are tentatively explained from a new angle. This interpretation is exploratory and new. At the same time, the author also proposes an experimental way to test the relative independence of space.At the same time, this paper attempts to strictly prove that Einstein's definition of simultaneity and spatial absoluteness in special relativity may be problematic.

This paper mainly explores the feasibility of using desert sand (DS) and recycled aggregate in cement stabilized base. Recycled coarse aggregate (RCA) and DS serve as the substitutes of natural coarse and fine aggregates, respectively, in cement stabilized base. A four-factor and four-level orthogonal test is designed to analyze the unconfined compressive strength, splitting tensile strength, and compressive resilient modulus. Furthermore, this paper investigates the effects of cement content, fly ash (FA) replacement rate, RCA replacement rate, and DS replacement rate on the road performance of cement stabilized base composing of RCA and DS. The test results reveal that the performance of cement stabilized base with partial RCA instead of natural coarse aggregate (NCA) and partial DS instead of natural fine aggregate satisfy the road use. Meanwhile, DS is beneficial to improve the strength of cement stabilized base. The correlation and microscopic analyses of the test results imply the feasibility of applying DS and recycled aggregate to cement stabilized base. It is hoped that this paper can offer a solid theoretical foundation for promoting the application of DS and recycled aggregate in road engineering.

The hump feature is one of the major instabilities in pump-turbines. When pump-turbines operate in the hump region, strong noise and serious fluctuations can be observed, which are harmful to their safe and stable operation and can even destroy the whole unit as well as water conveyance system. In this paper, a low specific speed (n_q = 36.1 min⁻¹) pump-turbine model was experimentally investigated. Firstly, the hump characteristic was obtained under 19 mm guide vane opening conditions. More interestingly, when the hump characteristic was measured in two directions (increasing and decreasing the discharge), characteristic hysteresis was found in the hump region. The analysis of performance characteristics reveals that the hump instability is the result of Euler momentum and hydraulic losses, and different Euler momentum and hydraulic losses in the two development processes lead to the hysteresis phenomenon. Then, 12 pressure sensors were mounted in the different parts of the pump-turbine model to obtain the time and frequency characteristics. The analysis of the corresponding fast Fourier transform confirms that the hump characteristic is related to low-frequency (0.04–0.15 times rotational frequency) vortices. The occurrence and cessation of vortices depend on the operating condition and measurement direction, which contribute to the hysteresis feature. Finally, the type of the low-frequency vortices was analyzed through the cross power spectrum.

The AREB/ABF (ABA response element binding) proteins in plants are vital for plant stress responses, but the understanding of AREB/ABFs in orchid species, an important traditional medicinal and ornamental plants, is limited. Here, twelve AREB/ABF genes were identified within three orchids’ complete genome and classified into three groups (groups I, II, and III) via a phylogenetic analysis, which was further supported by the analysis of their conserved motifs and gene structures. The cis-elements analysis showed that hormone response elements followed by light and stress responses were widely rich in AREB/ABFs. A prediction analysis of orchid ABRE/ABF-mediated regulatory network was further constructed through cis-regulatory elements (CREs) analysis of their promoter regions and revealed that several transcriptional factor (TF) gene family were abundant as the potential regulators for orchid AREB/ABFs. Expression profile analysis based on public transcriptomic data showed that most AREB/ABF genes have distinct tissue-specific expression patterns in orchid plants. Additionally, DcaABI5 as the homolog of ABA INSENSITIVE 5 (ABI5) from Arabidopsis was selected for further analysis. The results showed that Arabidopsis transgenic overexpressing DcaABI5 could rescue the ABA insensitive phenotype in the mutant abi5. Collectively, these findings will provide valuable information on AREB/ABF genes in orchids.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

Mangrove plant seedling cultivation is crucial for the protection, management and restoration of mangrove ecosystem. In this study, we focused on Kandelia obovata, a typical mangrove, and evaluated nursery cultivation with different combinations of three salinity levels (S1: 0 ppt, S2: 10 ppt, and S3: 20 ppt), three genealogies (EZD, JX, and YZ), and five growth media (M1: 100% loess, M2: 100% sandy, M3: 50% loess + 50% sandy, M4: 40% loess + 40% sandy + 20% peat, and M5: 40% loess + 40% sandy + 20% coir), by measuring the growth parameters such as mortality rate, seedling height, diameter, and biomass partition. These growth indexes were significantly affected by salinity and medium, and genealogies also had significant effects on mortality rate and biomass accumulation. S2 or S3 both had lower mortality and higher growth indexes than S1. M1 was the medium that increased seedlings height, diameter and biomass the most and had the lowest death rate. EZD and JX were also higher levels than YZ in these indicators, but the difference between them was not obvious. S3, M1, and EZD consistently performed well in fuzzy evaluation and quality assessment. Furthermore, combinations involving these treatments also produced highly favorable results. These results furnish both a theoretical and practical foundation for advancing nursery cultivation techniques and germplasm breeding of K. obovata in mangroves.

For a long time, physicists always directly use mathematical tools to deal with physical problems, and few people pay attention to the difference between mathematical theory and physical theory. Just like the dilemma that physicists once faced when dealing with the problem of blackbody radiation function.By analyzing the difference between the theoretical basis of mathematics and the theoretical basis of physics, this paper draws the following conclusions: (1) The theoretical basis of mathematics and the theoretical basis of physics are different, so when we use mathematical tools for physics research, we need to be very careful. (2) Finiteness and discreteness should be the basis of the whole physical theory; This paper points out that it is not advisable to use infinite " " and infinitesimal "0" without restriction and demonstration in physics, as well as the continuity of functions, which will bring a lot of trouble to physical theory.At the same time, through the analysis of Banach-Tarski paradox and Bertrand paradox, this paper proposes that if we revise the basic assumptions of probability theory: assuming that "points" have quantized sizes, and "lines" also have quantized widths. After the correction, we can not only avoid the troubles caused by Bertrand paradox, but also make probability theory better for practical application.

G protein-coupled receptor 15 (GPR15, also known as BOB) is an extensively studied orphan GPCR involving HIV infection, colonic inflammation and smoking-related diseases. Recently, GPR15 was deorphanized and its corresponding natural ligand demonstrated an ability of inhibiting cancer cell growth. However, no study reported the potential role of GPR15 in a pan-cancer manner. Using large-scale publicly available data from the Cancer Genome Atlas (TCGA) and the Genotype-Tissue Expression (GTEx) databases, we found that GPR15 expression is significantly lower in colon adenocarcinoma (COAD) than in normal tissues. And among 33 cancer types, GPR15 expression is significantly correlated with the prognoses of COAD, neck squamous carcinoma (HNSC), lung adenocarcinoma (LUAD) positively and stomach adenocarcinoma (STAD) negatively. This study also revealed that commonly upregulated gene set in the high GPR15 expression group (stratified via median) of COAD, HNSC, LUAD and STAD are enriched in immune systems, indicating that GPR15 might be considered as a potential target for cancer immunotherapy. Furthermore, we modelled the 3D structure of GPR15 and conducted the structure-based virtual screening. The top 8 hits compounds were screened and then subjected to molecular dynamics (MD) simulation for stability analysis. Our study provided novel insights into the role of GPR15 in a pan-cancer manner and discovered a potential hit compound for GPR15 antagonists.

In recent decades, with the ever-growing scale of video data, near-duplicate videos continue to emerge. Data quality issue caused by near-duplicate videos is becoming more and more prominent, which has affected the application of normal videos. Although current studies on near-duplicate video detection can be helpful to uncover data quality issues for videos, they still lack a process of automatic merging for the video data represented by high-dimensional features, which are difficult to automatically clean the near-duplicate videos to improve data quality for video datasets. At present, there are few studies on near-duplicate video data cleaning. The existing studies have the sensitive problems of video data orderliness and clustering initial center under a condition that prior distribution is unknown, which seriously affect the accuracy of near-duplicate video data cleaning. To address the above issues, an automatic near-duplicate video data cleaning method based on a consistent feature hash ring is proposed in this paper. First, a residual network with convolutional block attention modules, a long short-term memory deep network, and an attention model are integrated to construct an RCLA deep network with the multi-headed attention mechanism to extract spatiotemporal features of video data. Then, a consistent feature hash ring is constructed, which can effectively alleviate the sensitivity of video data orderliness while providing a condition of near-duplicate video merging. To reduce the sensitivity of the initial cluster centers to results of near-duplicate video cleansing, an optimized feature distance-means clustering algorithm is constructed by utilizing a mountain peak function on a consistent feature hash ring, which can implement automatic cleaning of near-duplicate video data. Finally, experiments are conducted based on a commonly used dataset named CC_WEB_VIDEO and a coal mining video dataset. Compared with some existing works, simulation results demonstrate that the performance of the proposed method.

Lucky bamboo (Dracaena sanderiana hort. ex Mast. = Dracaena braunii) is a domestic species widely cultivated for ornamental purposes in China. In March 2022, a severe occurrence of anthracnose disease was observed on the stems of lucky bamboo plants in a greenery retail store located in Nanjing, Jiangsu Province, China. The morphological characteristics of isolates obtained from diseased stem tissues were identical with those described for Colletotrichum species. Based on multilocus phylogenetic analysis with the internal transcribed spacer (ITS), actin (ACT) gene, and glyceraldehyde-3-phosphate dehydrogenase (GAPDH) gene, the pathogen was identified as Colleto-trichum gloeosporioides (Penz.) Penz. & Sacc. Pathogenicity was verified by mycelial plug-inoculating stem cuttings of one-year-old lucky bamboo plants and spray-inoculating whole one-year-old lucky bamboo plants, respectively. Koch’s postulates were fulfilled by the re-isolation of C. gloeosporioides from symptomatic tissues. To the best of our knowledge, this report describes the first time that C. gloeosporioides was observed to cause anthracnose on lucky bamboo in China.

Xinjiang, as a climate-sensitive region in northwest China, holds significant importance in studying extreme weather events for agricultural production and socioeconomic development. Based on data from 52 meteorological stations and 23 extreme climate indicators in Xinjiang from 1960 to 2021, the 5a moving average, linear trend estimation, climate tendency rate, and GIS spatial analysis methods are used to analyze the distribution and change characteristics of extreme climate. The results revealed that from 1960 to 2021, TXx, TNx, TXn, TNn, FD, ID, TN10p, TX10p, and WSDI showed a significant upward trend, while SU, TR, TN90p, TX90p, and CSDI showed a significant downward trend. What is more, the range of changes in the extreme temperature indexes from 1990 to 2021 is higher than that of 1960 to 1989. The high-value areas of extreme indexes are primarily concentrated in the northern part, while the high-value areas of cold event indexes are mainly distributed in the southern part. The upward/downward trends all accounting for over 80.00% of the entire region. The Rx1day, Rx5day, PRCPTOT, R95p, R99p, R10, R20, and R25 showed a significant growth trend from 1960 to 2021, and the range of change in the extreme precipitation indexes from 1990 to 2021 was lower than that from 1960 to 1989. Moreover, their high-value areas and high climate tendency areas are mainly concentrated in the northern and western parts of Xinjiang, with upward trends all accounting for over 71.00% of the entire region. The research results provide theoretical foundations for formulating climate risk strategies in the northwest region of China.

: During the period of COVID-19, the Chinese government implemented a series of actions to prevent the spread of the virus. It is noticed that these preventive actions have generated positive effects on air pollution in Wuhan and Beijing. And, due to the differences in city functions, geographic locations, meteorological conditions, and preventive action details between the two cities, noticeable difference is observed on how they reduced air pollution. This unfortunate incident has become a social sample for studying the industrial and livelihood activities impact on air pollution, otherwise would be highly impossible. This paper starts from observing data from NASA's real-time fine particulate matter (PM2.5) and NO2, and comparing the air pollution in this special time domain with previous years. It is discovered that both PM2.5 and NO2 have been reduced in Wuhan, while only NO2 has significant reduction in Beijing, during the COVID-19 responses. This suggests that the human activity suppression by the COVID-19 control yields different effects on different pollutants and in different cities. Possible reasons for such effects are analysed by considering the public health control levels as well as the pollutant migration, industrial activities, and the weather conditions.

Echinococcus granulosus is a harmful cestode parasite which could cause Cystic Echinococcosis in humans, various livestock species and wild animals. Calmodulin (CaM), a Ca²⁺ sensor protein, is widely expressed in eukaryotes and mediates a variety of cellular signaling activities. In our study, the CaM in Echinococcus granulosus (rEgCaM) was successfully cloned and the molecular and biochemical characterizations of rEgCaM were identified. The results showed that rEgCaM was a highly conserved calcium-binding protein, consisting of 149 amino acids. Immunoblot analysis revealed that rEgCaM could be identified using E. granulosus infected sheep serum. The usage of rEgCaM as antigen was evaluated by indirect ELISA which exhibited a high sensitivity of 90.3% but low specificity (47.1%). rEgCaM was mainly located in the tegument tissues and parenchymal region of protoscoleces, the tegument and inner body of adult worm and predominantly expressed in the germinal layer. The mRNA expression of rEgCaM in PSCs were gradually decreased with the increase death of PSCs. In electrophoretic mobility tests and ANS assays, rEgCaM showed a typical calcium-binding protein characteristics. This is the first report on CaM from E. granulosus and rEgCaM is considered to be involved in some important biological function of E. granulosus as a calcium-binding protein.

A bridged 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO) derivative (PN-DOPO) in combination with aluminum phosphates coated sepiolite (Sep@AlPO4) was used to improve the flame retardancy, thermal stability and mechanical properties of poly (ethylene oxide) (PEO)/poly (butylene adipate-co-terephthalate) (PBAT) blends. The synergistic effects of PN-DOPO and Sep@AlPO4 on the fire resistance, thermal decomposition behavior and mechanical properties of PEO/PBAT composites were investigated systematically. The results indicated that 5 wt % Sep@AlPO4 combined with 10 wt% PN-DOPO into PEO/PBAT achieved a V-1 rating in UL-94 test and the LOI value increased to 23.7%, meanwhile, the peak-heat release rate (p-HRR), av-HRR and total heat release (THR) values of PEO/PBAT/PN10%/Sep5% composites decreased by 35.6%, 11.0% and 23.0% compared with those of PEO/PBAT, respectively. The thermogravimetric analysis (TGA) results confirmed that PN-DOPO/Sep@AlPO4 could enhance the initial thermal stability and char yield of PEO/PBAT matrix, and TGA/Fourier transform infrared spectrometry (TGA-FTIR) results revealed that the composites exhibited the absorption peaks of phosphorous-containing groups and an increase in gas-phase volatiles during the thermal decomposition process. The digital photographs and morphological structures of char residues demonstrated that PN-DOPO and Sep@AlPO4 mixtures benefited to the formation of a more continuous and dense carbon layer on the composites surface during combustion. Rheological behavior revealed that a higher storage modulus, loss modulus and complex viscosity of PEO/PBAT/PN-DOPO/Sep@AlPO4 composites could also promote the cross-linking structure during burning. Furthermore, the PEO/PBAT/PN-DOPO/Sep@AlPO4 composites exhibited excellent mechanical properties in terms of elongation at break and flexural performance than the PEO/PBAT system. All the results demonstrated that PEO/PBAT system modified by the combination of PN-DOPO and Sep@AlPO4 not only exhibited excellent synergistic effect on the flame retardance, but also had good improvement on thermal stability and mechanical properties, indicating the potential application in areas requiring fire safety.

Objectives: The purpose of this study is to determine the association between umbilical venous blood flow (UVBF) to placental pulsatility index (PPI) ratio and gestational age (GA) in women undergoing prenatal assessments and adverse pregnancy outcome (APO) screening Methods: Between January and December 2022, sonographic examinations were conducted to assess the fetal umbilical cord insertion site in singleton fetuses, and hemodynamic indices of the umbilical artery, umbilical vein, and uterine artery were computed. Through regression analysis, we derived the optimal regression equation to elucidate the UVBF/PPI ratio parameters based on GA. Results: Among 492 singleton fetuses between 21+0 and 40+6 weeks of gestation in the final study. The average fetal UVBF/PPI ratio was 180.45±119.32. Correlation analysis revealed a positive relationship between the UVBF/PPI ratio and GA(p = .000). Using regression analysis, the best-fit regression equation was the linear function model, which explains the value of UVBF/PPI ratio parameters based on GA. Lower UVBF/PPI ratio revealed a positive relationship in the low birth weight fetuses (p=0.021) and higher preterm delivery rate (p=0.034). Cerebroplacental ratio (CPR) showed a high correlation with the UVBF/PPI ratio (r=0.471, p=0.000). Conclusions: The findings of our analyses revealed that contribute to our understanding of fetal hemodynamics and highlight the potential of UVBF/PPI ratio as a predictive marker for adverse pregnancy outcomes, such as preterm birth, low birth weight, or potential fetal hypoxemia. It might be useful for prenatal counseling and clinical purposes.

With the development of organizational biology and forced from the EU Cosmetic Regulation (EU/1223/2009) with the complete ban of animal testing for cosmetic purposes, 3D skin models have been widely developed due to their similar physiological structure and metabolic function to native human tissue. 3D skin models for in vitro cosmetic evaluation are still promising alternative methods for evaluating phototoxicity, corrosivity and irritation. These models have been used for early screening and later validation of toxicity and efficacy evaluation by many well-known cosmetic companies. 3D skin models have become an important tool in cosmetic evaluation research. This article reviews the development of 3D skin models and their application in cosmetic evaluation. An outlook on the current application and future technological development directions in the cosmetic field is also presented.

Balanced and coordinated economic development across regions is a critical goal of regional economic development and new-type urbanization in China. However, few studies have examined economic growth convergence clubs at the county level. To extend the research on convergence clubs, this research applies a log t convergence test and a dynamic spatial ordered Probit model (DSOP) to endogenously identify economic growth convergence clubs in counties and to examine the influence of initial states and structures on club convergence probability. The study sample covers 2286 counties of China from 1992 to 2010. The results show significant convergence club patterns at the county levels, resulting in the gradual formation of six convergence clubs. The DSOP estimation results show that per capita fixed assets, population density and industrialization have promoted convergence club formation to varying degrees.

This paper presents a theory on graph topological structure and graph coloring, proving that for any N-order graph structure (with a topological structure similar to ), the maximum number of colors required for coloring is less than or equal to . The Four Color Theorem is just one special case of this theory, with the maximum structure size for a four-color graph being a 4-order structure graph, hence requiring only a maximum of 4 colors for coloring.

This paper is the third application-oriented paper based on the "unified theory of forces" and also addresses the shortcomings of previous research in fully explaining the origin and nature of the weak force. The main conclusions of this paper are as follows: (1) It is argued that neutrinos are generated by the gravitational field, and their generation mechanism is similar to the radiation of photons from electron orbital transitions. Particles undergoing orbital transitions in a gravitational field will emit neutrinos. (2) We rigorously derive the energy formula for neutrinos and demonstrate that the energy formula for neutrinos does not comply with the Planck energy formula. Neutrinos with higher energy have longer wavelengths and are more easily observed in experiments.

In response to the structural optimization problem of PCB stator coreless disc motors, the orthogonal response surface method was used to optimize the motor structure, determine the basic parameters of the motor preliminarily, and conduct orthogonal experiments on the motor parameters based on the optimization design objectives, The optimization factors were the quantity of magnetic pole of the motor rotor, the ratio of main/auxiliary pole size, the thicknessof the permanent magnet, and the air gap length.The motor torque，the amplitude of magnetic density of the air gap and waveform distortion rateare used as optimization objectives. The motor parameters that make the motor torque reach the maximum, the air gap magnetic density maximum, and the waveform distortion rate minimum. Due to the use of PCB plates instead of motor stator cores in PCB coreless disc motors,The service life of the PCB board during motor operation will be reduced with the temperature rise generated by the stator winding To solve this problem, the response surface analysis of the motor is carried out to reduce the temperature rise of the stator windings during the operation of the motor. PCB board and stator winding are the main factors affecting the temperature rise of the motor.Taking the thickness of the PCB board, the hole diameter on the board, and the uneven width of the stator winding as optimization factors, the motor parameters with the lowest temperature rise of the motor winding are obtained. Simulation analysis is conducted using Ansys/Maxwell software, and the results prove the feasibility of optimization.

The mesoporous heteroatom molecular sieve MCM-41 bulk crystals with the crystalline phase were synthesized via a one-step hydrothermal method using an ionic complex as template. The ionic complex template was formed by interaction between cetyltrimethylammonium ions and metal complex ion [M (EDTA)]2- (M=Co or Ni ). The materials were characterized by X-ray diffraction, scanning electron microscopy, high-resolution transmission electron microscopy, N2 adsorption–desorption isotherms, and X-ray absorption fine structure spectroscopy. The results showed that the materials possess a highly ordered mesoporous structure with the crystalline phase and possess high uniform ordered arrangement channels. The structure is in the vertical cross directions with a crystalline size of about 12 µm and high specific surface areas. The metal atoms were incorporated into the zeolite frameworks in the form of octahedral coordinate and have a uniform distribution in the materials. The amount of metal complexes formed by metal ion and EDTA is an essential factor for the formation of the vertical cross structure. Comparing to Si-MCM-41, the samples exhibited better conversion, higher selectivity for cumene cracking.

At the end of 2019, while the world was being hit by the COVID-19 virus and, consequently, was living a global health crisis, many other pandemics were putting humankind in danger. The role of social media is of paramount importance in these kinds of contexts since they help health systems to cope with emergencies by contributing to conducting some activities such as the identification of public concerns, the detection of infections’ symptoms, and the traceability of the virus diffusion. In this paper, we have analyzed comments on events related to cholera, ebola, HIV/AIDS, influenza, malaria, Spanish influenza, swine flu, tuberculosis, typhus, yellow fever, and zika, collecting 369,472 tweets from the 3rd of March to the 15th of September, 2022. Our analysis has started with the collection of comments composed of unstructured texts on which we have applied natural language processing solutions. Afterward, we have employed topic modelling and sentiment analysis techniques to obtain a collection of people’s concerns and attitudes toward these pandemics. According to our findings, people's discussions were mostly about malaria, influenza, and tuberculosis and the focus was on the diseases themselves. As regards emotions, the most popular were fear, trust, and disgust where trust is mainly regarding HIV/AIDS tweets.

Ti and its alloys are the most commonly used materials for biomedical applications. However, bacterial infection after implant placement is still one of the significant rising complications. Therefore, the application of the antimicrobial agents into implant surfaces to prevent implant-associated infection has attracted lots of attention. Scientific papers have shown that inorganic antibacterial metal element (e.g. Ag, Cu, Zn) can be introduced to implant surfaces with the addition of metal nanoparticles or metallic compounds into electrolyte via micro-arc oxidation (MAO) technology. In this review, the effects of the composition and concentration of electrolyte and process parameters (e.g. voltage, current density, oxidation time) on morphological characteristics (e.g. surface morphology, bonding strength), antibacterial ability and biocompatibility of MAO antimicrobial coating were discussed in detail. Anti-infection and osseo-integration can be simultaneously accomplished with the selection of the proper antibacterial elements and operating parameters. Besides, MAO assisted by magnetron sputtering (MS) to endow Ti-based implant materials with superior antibacterial ability and biocompatibility was also discussed. Finally, the development trend of MAO technology in the future was forecasted.

This study presented a novel and sustainable method for producing chitin nanocrystals (PA-ChNCs) using phosphoric acid hydrolysis. The produced PA-ChNCs were used as stabilizers for Pickering emulsions and their physicochemical properties as well as stabilization mechanisms were systematically investigated. The PA-ChNCs exhibited small particle sizes and high surface areas, enabling an effective adsorption at the oil/water interface, which prevented coalescence in Pickering emulsions. The particle size and surface charge PA-ChNCs were strongly pH-dependent, which were critical factors for stabilizing Pickering emulsions. The study showed that emulsions with higher O:W ratios (50%) exhibited larger droplets but greater viscosity, forming a stable gel-like matrix that was more stable than emulsions with other O:W ratios after storage for 30 days. Emulsions with higher PA-ChNCs concentrations (2.0 wt%) and higher pH values (pH 10) showed small droplets and high viscosity, leading to stable emulsions. This research contributes to the development of sustainable and effective emulsifiers for use in the food industry, making utilization of seafood waste in an eco-friendly manner possible. Overall, this study highlights the potential of using newly developed PA-ChNCs as stabilizers for Pickering emulsions in food products.

The electroencephalogram (EEG) is a record of brain activity. Brain Computer Interface (BCI) technology formed by the EEG signal has become one of the hotspots at present. How to extract the feature signal of EEG is the most basic research of BCI technology. In this paper, A new method of recognizing fatigue, conscious, concentrated state of human brain is proposed by the combination of discrete wavelet transform and the neural network based on EEG signal. First of all, the law signal is preprocessed by the wavelet denoising method because the law EEG signal contains a large number of high frequency noise, which is decomposed into multi-layer high frequency signal and low frequency signal. thus, δ wave, θ wave, α wave, β wave are obtained by the wavelet transform. And then, frequency band energy of the different wave is regards as the feature signal of EEG. In the experiment, the feature signal is classified by radial basic function (RBF) and annealed chaotic competitive learning network (ACCLN). RBF and ACCLN networks are trained with 500 sets of sample data and are tested by 100 sets of samples in different mental states. The experimental results show that the average accuracy of RBF network under three conditions are 88.75%, 88.25%, 88.5%, respectively, and the correct rate of ACCLN network is 97%, 98%, 98%, respectively.

This literature review paper delves into the synergies between Climate-Smart Agriculture (CSA) and the effective management of food losses. With the escalating challenges posed by climate change and the pressing need to address food security concerns, the intersection of these two critical domains becomes paramount for sustainable agricultural practices. The review explores existing research on the implementation of climate-smart agricultural techniques and their impact on mitigating food losses throughout the agricultural value chain. The paper synthesizes findings related to climate-resilient crop varieties, precision farming, water-use efficiency, and sustainable soil management, highlighting their contributions to reducing post-harvest losses and enhancing overall food security. In addition to summarizing current knowledge, this paper identifies gaps in the literature and proposes avenues for future research. This review serves as a foundation for researchers, policymakers, and practitioners seeking to contribute to the advancement of climate-smart agriculture and the reduction of food losses, paving the way for a more sustainable and resilient global food system.

The pathogenicity of grapevine geminivirus A (GGVA), a recently identified DNA virus, to grapevine plants remains largely unclear. Here, we report a new GGVA isolate (named GGVAQN) obtained from grapevine ‘Queen Nina’ plants with severe disease symptoms; the infectious clone of GGVAQN (pXT-GGVAQN) was also constructed. Infection assays indicated that Nicotiana benthamiana plants inoculated with GGVAQN display upward leaf curling and chlorotic mottling symptoms. Direct injection of Agrobacterium tumefaciens cells carrying pXT-GGVAQN into roots of in vitro-grown ‘Red Globe’ grape plantlets by syringe led to systemic infection with GGVAQN, and the plants exhibited chlorotic mottling symptoms on their upper leaves, and downward curling, interveinal yellowing, and leaf-margin necrosis symptoms on their lower leaves. Our results provide insights into the pathogenicity of GGVA, and a simple and efficient inoculation method to deliver infectious viral clones to woody perennial plants.

In order to study the performance of a new type of cement-based grouting material under the coupling effect of freezing-thawing cycle and sulfate attack, experiments were designed and carried out. The damage mechanism of the material under the coupling effect of freezing-thawing and Na2SO4 solution was analyzed by measuring the mass change, relative dynamic elastic modulus, compressive strength loss and microstructure of the new grouting material. With increasing freeze-thaw cycles, mass loss and compres-sive strength loss of the sample in 15% Na2SO4 solution gradually increase, and the relative dynamic elastic modulus gradually decreases. During a 30-cycle freeze-thaw cycle, the mass loss rate, compressive strength loss rate, and relative dynamic elastic modulus of the sample are 4.17%, 24.59%, and 84.3%, respectively, showing good corrosion resistance and frost resistance durability. Microscopic analysis showed that SO42- caused the decomposition of C-S-H gel in the sample and the formation of Gypsum, and the widening of crack width aggravated the internal deterioration, indicating that the material deterioration rate increased under the dual-factor coupling effect.

Halide perovskite materials gain enormous attention for their semiconducting properties, higher power conversion efficiency and potential applications in a wide range field of studies along with their two key limitations: stability and toxicity. In spite of great progress made on the halide perovskites and many promising research developments, overcoming these limitations is not realized yet. Therefore, coordination engineering of new framework for obtaining alternative new halide perovskite materials and fundamental understanding of the coordination chemistry and electronic interactions forming the structure of these newly engineered halide perovskite materials might be one way in order to overcome the issues related to both stability and toxicity. In this review, the current development of halide perovskite families, both lead halide perovskites and lead free halide perovskites followed by coordination engineering of the new frameworks to engineer new halide perovskite materials will be reviewed comprehensively. Moreover, all the concerns of the fundamental ideas of coordination chemistry and electronic interactions that are keys in forming the halide perovskite structures are discussed in detail and form the main aim of this review. Interestingly, we also discuss recent potential energy applications beyond photovoltaic and this review has completed with an essential and open question: ‘what could happen in the future of halide perovskites?’ in order to excite commercial enterprises and research institutions again as well as to get motivating new predictions on the future continuity of this field.

This study takes a two-echelon agricultural products supply chain (APSC) composed of an agricultural product processor (processor) and an agricultural product supermarket (supermarket) as the research object. In order to ensure the stable supply of high-quality agricultural products, this paper considers both fairness concern and corporate social responsibility (CSR), and establishes four Stackelberg game models with or without considering fairness concern and CSR, and obtains the influence mechanism of fairness concern and CSR on bilateral quality efforts in APSC through comparative analysis and numerical analysis. Research shows that the supermarket’s fairness concern can take the role of "profit distribution mechanism", but it is not conducive to improving bilateral quality efforts resulting in the inability to improve market demand, and it is not conducive to improving the utility of the supply chain system and consumer surplus; both members of APSC sharing CSR can not only improve the quality of agricultural products and promote the expansion of market demand, but also can achieve Pareto improvement of both profit of all members and supply chain system. Besides, The CSR shared by both members has a greater impact on bilateral quality efforts decision than the supermarket’s fairness concern, and thus the positive effect of CSR can overcome the negative effect of supermarket’s fairness concern.

In the future, the pursuit of high-quality economic development and a focus on ecological environmental protection in China will inevitably result in significant conflicts between land use and ecological land use. The challenge lies in achieving sustainable high-quality development while simultaneously protecting the ecological environment, optimizing the land use structure, and promoting a harmonious relationship between humans and the land. These challenges are faced by all regions. Land use conflicts primarily occur in peri-urban areas characterized by prominent economic development and urban agglomeration. Previous studies have mainly focused on analyzing the effects of land use on habitat quality during intense urbanization. However, it is important to recognize that land pressure encompasses economic, ecological, and social aspects. To gain a comprehensive understanding of the spatial conflict of land use and the impact on habitat quality in Ankang, a city that has been advocating ecological protection for the past two decades, this study aims to objectively analyze the spatial trends in land use changes in such cities. Additionally, it aims to provide insights for the harmonious development of land use in eco-region-oriented cities. Using the SSP-RCP scenarios provided by CMIP6, this paper employs a system analysis method, PLUS model, InVEST model, and land use conflict measurement model to dynamically simulate the future habitat quality and spatial conflict patterns of land use in Ankang City. The study explores the spatial coupling effect of both factors under different scenarios. The results indicate the following:(1) Under different future shared socio-economic path scenarios, land use intensity and land conflict levels follow the order of SSP585 (high forcing scenario), SSP370 (medium to high forcing scenario), SSP245 (medium forcing scenario), and SSP126 (low forcing scenario), with intensity and conflict decreasing accordingly. (2) The overall development trend in Ankang City reveals an intensification of land use conflicts and a decrease in habitat quality. The expansion rate of construction land is increasing and exhibiting aggregation, while agricultural land area is expanding and forest land area is continuously decreasing. (3) Land use intensity exhibits a significant positive correlation with land conflict levels, while land conflict levels demonstrate a significant negative correlation with habitat quality. These findings suggest that land use has had some impact on the ecological environment, with indications of habitat degradation. Even in Ankang, where ecological development is highly valued, the city will gradually face conflicts between ecological protection and economic development in future scenarios. The study highlights that Ankang's future development space will be constrained within the context of environmental protection, leading to greater land use conflicts in urban and surrounding areas. Consequently, the quality of habitats will inevitably decline. Therefore, it is crucial to allocate sufficient space for economic development while simultaneously prioritizing ecological protection. This approach will ensure a healthy economic development trajectory and foster a harmonious relationship between humans and the land.

In order to overcome the limitation of the traditional adaptive Unscented Kalman Filtering (UKF) algorithm in noise covariance estimation for statement and measurement, we propose a hybrid adaptive UKF algorithm based on combining Maximum a posteriori (MAP) criterion and Maximum likelihood (ML) criterion, in this paper. First, to prevent the actual noise covariance deviating from the true value which can lead to the state estimation error and arouse the filtering divergence, a real-time covariance matrices estimation algorithm based on hybrid MAP and ML is proposed for obtaining the statement and measurement noises covariance, respectively; and then, a balance equation the two kinds of covariance matrix is structured in this proposed to minimize the statement estimation error. Compared with the UFK based MAP and based ML, the proposed algorithm provides better convergence and stability.

Cytosine (C) to uracil (U) RNA editing is one of the most important post-transcriptional processes, however exploring C-to-U editing events efficiently within the crop mitochondrial genome remains a challenge. An improving predictive RNA editor for crop mitochondrial genomes, iPReditor-CMG, was proposed, which was based on SVM, three common crop mitochondrial genomes and self-sequenced tobacco mitochondrial ATPase. After multi-combination feature extracting, high-dimension feature screening and multi-test independent predicting, the results showed that the average accuracy of intraspecific prediction was 0.85, and the highest value even up to 0.91, which outperformed the previous reference models. While the prediction accuracies were 0.78 between dicotyledons and no more than 0.56 between dicotyledons and monocotyledons, implying a possible similarity in C-to-U editing mechanisms among close relatives. The best model was finally identified with an independent test accuracy of 0.91 and an area under the curve of 0.88, and further suggested that five unreported feature sequences TGACA, ACAAC, GTAGA, CCGTT and TAACA were closely associated with the editing phenomenon. Multiple evaluation findings supported that the iPReditor-CMG could be effectively applied to predict crop mitochondrial editing sites, which may contribute to insight into their recognition mechanisms and even other post-transcriptional events in crop mitochondria.

Buckling defect will appear on the outer surface of the deformed ring during constrained ring rolling (CRR) of aluminum alloy thin wall conical ring with inner high ribs (AATWCRIHR), if the geometrical dimension of the ribs doesn't match the wall thickness. To avoid the buckling defect, a quantitative method for characterizing the degree of the buckling defect is proposed using the area of buckling profile. Then an orthogonal experimental scheme was designed taking the width of the middle rib, thickness of wall, and height of the middle rib as design variables and defining the area of buckling profile as optimization objective. Subsequently, a quadratic polynomial response surface model was established by combining the optimization algorithm with the finite element method (FEM), and the geometrical dimension of the middle ribs of the deformed AATWCRIHR is optimized. Also the optimal parameter combination to minimize the area of buckling profile is obtained and verified using FE simulation. Results show that the AATWCRIHR after optimization doesn’t generate the buckling defect during constrained ring rolling, and it is proved that the quantitative buckling defect representation method and the optimization design method based on the response surface model and the finite element simulation results are feasible for the constrained ring rolling process of the AATWCRIHR.

To estimate the progressive collapse resistance capacity of a multi-column frame tube structure with the assembled truss beam composite floor (ATBCF), the pushdown analysis, and the nonlinear dynamic analysis as well, are conducted for such a structure by using the alternate load path (ALP) method. The bearing capacities of the remaining structures at three different work conditions, which are the side middle column failure, the edge middle column failure, and the corner column failure, are individually studied, and the collapse mechanism for the remaining structures is analyzed from the aspects of the internal force redistribution and the failure mode of the second defense line. Simultaneously, the influence of the column failure time on the dynamic response of the remaining structure and the dynamic amplification coefficient are discussed. The results show that the residual bearing capacity of the remaining structure with the bottom corner column failure is higher than that of the one with the side or edge middle column failure, while the latter has a stronger plastic deformation capacity. When the ALP method is adopted to operate the progressive collapse analysis, it is reasonable to take the column failure time as 0.1 times of the first-order vertical vibration period of the remaining structure, and it is suitable to set the dynamic amplification coefficient as of 2.0, which is the ratio of the maximum dynamic displacement to the static displacement of the remaining structure under the transient loading condition.

The article delves into the intricate phase transitions of 1-Octadecanol and n-Nonadecane within a binary system, unveiling dynamic structural changes under varying conditions. Through Fouri-er-transform infrared (FTIR) analysis, specific molecular vibrations were identified, shedding light on the molecular composition and interactions. The study highlights the challenges in detecting subtle phase transitions and emphasizes the individuality of molecular behaviours in closely related compounds. The findings underscore the complexity of phase transitions in binary systems and advocate for a nuanced approach to studying molecular structures and behaviours. Addi-tionally, the research contributes valuable insights into the molecular dynamics of Organic Polymer Functional Adsorption Materials, offering implications for synthetic waxy layers in plant epidermis.

Structural health monitoring has been studied by a number of researchers as well as various industries to keep up with the increasing demand for preventive maintenance routines. This work presents a novel method for reconstruct prompt, informed strain/stress responses at the hot spots of the structures based on strain measurements at remote locations. The structural responses measured from usage monitoring system at available locations are decomposed into modal responses using empirical mode decomposition. Transformation equations based on finite element modeling are derived to extrapolate the modal responses from the measured locations to critical locations where direct sensor measurements are not available. Then, two numerical examples (a two-span beam and a 19956-degree of freedom simplified airfoil) are used to demonstrate the overall reconstruction method. Finally, the present work investigates the effectiveness and accuracy of the method through a set of experiments conducted on an aluminium alloy cantilever beam commonly used in air vehicle and spacecraft. The experiments collect the vibration strain signals of the beam via optical fiber sensors. Reconstruction results are compared with theoretical solutions and a detailed error analysis is also provided.

Microcystis aeruginosa is a common cyanobacteria found in water blooms and often causes ecological harm. Antibiotics are also increasingly used for the prevention and treatment of bacterial infections in aquaculture. However, since most antibiotics cannot be fully metabolized, they enter the water environment and cause ecological impacts. In this paper, the effects of the two quinolone antibiotics (enrofloxacin and ciprofloxacin) on the population density and microcystins (MCs) production of Microcystis aeruginosa were studied. It is of great significance for the ecological risk assessment of antibiotics to the water environment. The results showed that the 96h EC50 values of enrofloxacin and ciprofloxacin to Microcystis aeruginosa were 56.10mg/L and 49.80mg/L respectively, and the toxicity of ciprofloxacin to Microcystis aeruginosa was slightly stronger than that of enrofloxacin. With the increase of the two quinolone antibiotic concentration, the growth inhibition rate (IR) increased, but when the concentration reached a certain height, the IR would reach its threshold. Long-term exposure to low concentrations of these two quinolone antibiotics is not only more likely to lead to the outbreak of Microcystis aeruginosa, but also increase its toxin production capacity. The highest contents of MCs in enrofloxacin and ciprofloxacin groups were 95.539 μg/g and 93.720 μg/g, respectively. The MCs value of these three enrofloxacin treatment groups was more than above 51.8 times that of control group (CK) on the 4th day; from 8th day to 14th day, the MCs value of these three enrofloxacin treatment groups was more than above 3.2 times that of CK group. For another ciprofloxacin, the MCs value of the treatment group was more than 64.98 times that of the CK group on the 4th day, and from 8th day to 14th day, the MCs value of the treatment group was more than 2.7 times that of the CK group. These findings provide crucial management rationale.

Polysaccharide from Ficus carica L. (FCP) exert multiple biological activities, as a biological macromolecule, the available knowledge about the specific structures and mechanisms of biological activity of purified 'Brunswick' fig polysaccharide is currently limited. In the present study, by chemical purification and characteristics identified via specific instruments, and then the impact of FCP on the immunomodulation activity in vitro and in vivo was examined. Structural char-acteristics showed that the molecular weight of the FCP was determined to be 127.5 kDa, the primary monosaccharides present in the FCP were galacturonic acid (GalA), arabinose (Ara), galactose (Gal), rhamnose (Rha), glucose (Glc), and xylose (Xyl) at a ratio of 0.321:0.287:0.269:0.091:0.013:0.011. Based on the investigation of in vitro immunomodulatory ac-tivity, FCP was found to stimulate the production of NO, TNF-α, and IL-6 and increased the pi-nocytic activity of macrophages. Further analysis revealed that FCP activated macrophages by interacting with toll-like receptor 4 (TLR4). Moreover, the in vivo test results indicate that FCP showed significant increase serum pro-inflammatory factors in immunosuppressed mice. Overall, this study suggests that FCP has the potential to be utilized as a novel immunomodulator in the pharmaceutical and functional food industries.

Day-ahead forecasting of electricity prices is important in deregulated electricity markets for all the stakeholders: energy wholesalers, traders, retailers, and consumers. Electricity price forecasting is an inherently difficult problem due to its special characteristic of dynamicity and non-stationarity. In this paper, we present a robust price forecasting mechanism that shows resilience towards aggregate demand response effect and provides highly accurate forecasted electricity prices to the stakeholders in a dynamic environment. We employ an ensemble prediction model in which a group of different algorithms participate in predicting the price for each hour of a day. We propose two different strategies, namely, Fixed Weight Method (FWM) and Varying Weight Method (VWM), for selecting each hour's expert algorithm from the set of participating algorithms. In addition, we utilize a carefully engineered set of features selected from a pool of features derived from information such as past electricity price data, weather data, and calendar data. The proposed ensemble model offers better results than both the Pattern Sequence-based Forecasting (PSF) method and our own previous work using Artificial Neural Networks (ANN) alone do on the datasets for New York, Australian, and Spanish electricity markets.

Multimodal remote sensing data classification can enhance the model’s ability to distinguish land features through multimodal data fusion. In this context, how to help models understand the relationship between multimodal data and target tasks is the focus of researchers. Inspired by human feedback learning mechanisms, causal reasoning mechanisms, and knowledge induction mechanisms, this paper integrates causal learning, reinforcement learning, and meta learning into a unified remote sensing data classification framework and proposed the causal meta-reinforcement learning (CMRL). First, based on feedback learning mechanisms, we have overcome the limitations of traditional implicit optimization of fusion features and customized a reinforcement learning environment for multimodal remote sensing data classification tasks. Through feedback interactive learning between agents and the environment, we help them understand the complex relationships between multimodal data and labels, thereby achieving full mining of multimodal complementary information. Second, based on the causal inference mechanism we designed causal distribution prediction action, classification reward, and causal intervention reward, capturing pure causal factors in multimodal data and cutting off false statistical associations between non-causal factors and class labels. Finally, based on the knowledge induction mechanism, we designed a bi-layer optimization mechanism based on meta-learning. By constructing a meta training task and meta validation task simulation model in the generalization scenario of unseen data, we helped the model induce cross-task shared knowledge, thereby improving its generalization ability for unseen multimodal data. The experimental results on multiple sets of multimodal datasets show that the proposed method achieved state-of-the-art performance in multimodal remote sensing data classification tasks.

Cancer is a common illness with a high mortality. Compared to traditional technologies, biomarkers detection, with low cost and simple operation, has higher sensitivity and faster speed in early screening and prognosis of cancer. Therefore, extensive research has been focused on the development of biosensors and the construction of sensing interfaces. Molybdenum disulfide (MoS2) is a promising two-dimensional (2D) nanomaterial, whose unique adjustable bandgap shows excellent electronic and optical properties in the construction of biosensor interfaces. It not only has the advantages of high catalytic activity and low manufacturing costs, but also can further expand the application of hybrid structures by different functionalization, and is widely used in various biosensors fields. Herein, the application of electrochemical and optical sensing platforms based on MoS2 in the detection of cancer biomarkers was comprehensively reviewed. Firstly, the structure and preparation method of MoS2 were introduced, and its applicable characteristics in the field of biosensors were explored. Secondly, we comprehensively reviewed the recent construction and application of sensing platform based on MoS2 in the field of cancer biomarkers detection in both electrochemical and optical aspects. The prime characteristics and application performances of MoS2 and its composites were emphasized. Additionally, we also involved some other types of biosensors based on MoS2. Finally, we summarized the challenges and development prospects of MoS2 in the application of cancer biomarkers detection, and provided some insights for the application potential of this kind of emerging nano-materials in a broader field.

We consider the financial planning problem of a retiree wishing to enter a retirement village at a future uncertain date. The date of entry is determined by the retiree's utility and bequest maximisation problem within the context of uncertain future health states. In addition, the retiree must choose optimal consumption, investment, bequest and purchase of insurance products prior to her full annuitisation on entry to the retirement village. A hyperbolic absolute risk-aversion (HARA) utility function is used to allow necessary consumption for basic living and medical costs. The retirement village will typically require an initial deposit upon entry. This threshold wealth requirement leads to exercising the replication of an American put option at the uncertain stopping time. From our numerical results, active insurance and annuity markets are shown to be a critical aspect in retirement planning.

In typical Cobalt-chromium (CoCr) alloys powders, aluminum oxide (Al₂O₃) powder can be added. In the present study, we successfully prepared alloyed samples of various powder ratios by laser cladding, and analyzed their microstructure and carbide structural characteristics, including microhardness, biological properties, morphology (using scanning electron microscopy), and crystal structure (using X-ray powder diffraction). Elemental distribution was also determined by energy-dispersive X-ray spectral analysis. The results showed that Al₂O₃ addition caused the alloy to change from slender columnar crystals to columnar grains similar, to equiaxed grains. In addition, Al₂O₃ agglomeration zones appeared, and carbide structures were altered. The mechanism of the observed performance changes was also analyzed.

Concrete cracks and local damage can affect the bond performance between concrete and steel bars, thereby reducing the durability of reinforced concrete structures. Compared with general concrete crack repair methods, biomineralization repair not only has effective bonding capabilities but is also particularly environmentally friendly. In view of this, this study aimed to apply biomineralization technology to repair damaged fiber-reinforced lightweight aggregate concrete (LWAC). Two groups of LWAC specimens were prepared. The control group used lightweight aggregates (LWAs) without bacterial spores and nutrient sources, and the experimental group used LWAs containing bacterial spores and nutrient sources. These specimens were first subjected to compression tests and pull-out tests, respectively, and thus were damaged. After the damaged specimen healed itself in different ways for 28 days, secondary compression and pull-out tests were conducted. The self-healing method of the control group involved placing the specimens in an incubator. The experimental group was further divided into experimental group I and experimental group II. The self-healing method of experimental group I was the same as that of the control group. The self-healing method of experimental group II involved soaking the specimen in a mixed solution of urea and calcium acetate for two days, and then taking it out and placing it in an incubator for two days, with a cycle of four days. The test results showed that, compared with the control group specimens, the relative bond strength ratio of the experimental group II specimens increased by 17.9%. Moreover, the EDS and XRD analysis results confirmed that the precipitate formed at the crack was calcium carbonate, which improved the compressive strength and bond strength after self-healing. This indicates that the biomineralization maintenance method used in experimental group II is more effective.

In high-risk railway construction, personal protective equipment monitoring is critical but challenging due to small and frequently obstructed targets. We propose YOLO-EA, an innovative model that enhances safety measure detection by integrating ECA into its backbone's convolutional layers, improving discernment of minuscule objects like hardhats. YOLO-EA further refines target recognition under occlusion by replacing GIoU with EIoU loss. YOLO-EA's effectiveness was empirically substantiated using a dataset derived from real-world railway construction site surveillance footage. It outperforms YOLOv5, achieving 98.9% precision and 94.7% recall, up 2.5% and 0.5% respectively, while maintaining real-time performance at 70.774 fps. This highly efficient and precise YOLO-EA holds great promise for practical application in intricate construction scenarios, enforcing stringent safety compliance during complex railway construction projects.

This paper studies an effective finite difference scheme for solving two-dimensional Heston stochastic volatility option pricing model problems. A dynamically balanced up-downwind strategy for approximating the cross-derivative is implemented and analyzed. Semi-discretized and spatially nonuniform platforms are utilized. The numerical method comprised is simple, straightforward with reliable first order overall approximations. The spectral norm is used throughout the investigation and numerical stability is proven. Simulation experiments are given to illustrate our results.

With the rapid development of society and the deteriorating natural environment, there has been an increase in public events. This study aimed to explore how sadness and fear in the context of public emergency influence moral judgments. This research first induced feelings of sadness and fear by videos about public events and music, and then used moral scenarios from the CNI model to assess participants’ moral thinking. In Study 1, participants were divided into sadness group and neutral group, while in Study 2, participants were divided into fear group and neutral group. During the experiment, participants were exposed to different videos related to public events to induce the corresponding emotions, and emotional music was continuously played throughout the entire experiment. Participants were then asked to answer questions regarding moral judgments. The results showed that based on CNI model, sadness induced in the context of public events significantly increased C parameter, without affecting N or I parameter. Fear increased I parameter, without affecting C or I parameter. That is, sadness and fear induced in the context of public events can influence moral judgments. Specifically, sadness increases individuals’ sensitivity to consequence, and fear increases the general preference for inaction in moral judgments.

For personalized recommender systems,matrix factorization and its variants have become mainstream in collaborative filtering.However,the dot product in matrix factorization does not satisfy the triangle inequality and therefore fails to capture fine-grained information. Metric learning-based models have been shown to be better at capturing fine-grained information than matrix factorization. Nevertheless,most of these models only focus on rating data and social information, which are not sufficient for dealing with the challenges of data sparsity. In this paper,we propose a metric learning-based social recommendation model called SRMC.SRMC exploits users' co-occurrence pattern to discover their potentially similar or dissimilar users with symmetric relationships and change their relative positions to achieve better recommendations.Experiments on three public datasets show that our model is more effective than the compared models.

The branch prediction units (BPUs) generally have security vulnerabilities, which can be used by attackers to obtain the execution status, jump directions, and jump address of conditional branches, and the existing protection methods cannot defend against these attacks. Therefore, this article proposes a hardware security protection method for conditional branches of embedded systems. This method calculates the number of updates to the branch target buffer (BTB). When it exceeds the threshold, BTB is locked to prevent attackers from analyzing the execution status of branches based on the time difference of whether BTB is updated. Moreover, the hybrid physical unclonable function (PUF) circuit is designed to provide confidentiality protection for the jump directions, jump addresses, and their indexes, preventing attackers from stealing these critical data. If these mechanism fails and attackers successfully tamper with conditional branches, this paper proposes a control flow integrity (CFI) protection mechanism based on branch labels to timely detect tampering with instruction codes, jump addresses, and jump directions. The proposed method is implemented and tested on FPGA. The experimental results show that this method can achieve fine-grained security protection for conditional branches, with about 5.4% resource overhead and less than 5.5% performance overhead.

The wellness economy has developed rapidly recently, particularly in wellness tourism. Wellness tourism transforms sustainable strategy through the availability of extended multi-actor engagement in service innovation to further the tourism experience. Therefore, when operating a wellness tourism destination, it is necessary to encourage multi-actor engagement in service innovation to achieve sustainable development. This paper introduces a mixed research method with the SWOT-AHP-QSPM, as it qualitatively analyzes the advantages, disadvantages, opportunities, and threats, constructs an evaluation index system, conducts quantitative analysis using the analytic hierarchy process, determines the index weight and weighted score, and calculate the sustainable development strategy, which is appropriate for wellness development of Chongqing Tea Mountain and Bamboo Forest National Forest Park. Purposive field surveys and personal interviews were conducted in Chongqing forest tourism destinations, involving 356 effective respondents. The research reveals that multi-actor engagement significantly enhances sustainable development. These findings bridge service innovation knowledge gaps and provide valuable insights for forest tourism destination management and sustainable policy strategies to elevate multi-actor engagement in forest sites.

The COVID-19 pandemic resulted in government restrictions that altered the lifestyle of people worldwide. Studying the impact of these restrictions on exercise behaviors will improve our understanding of environmental factors that influence individuals’ PA. We conducted a retrospective analysis using an index of government pandemic stringency developed by Oxford and a wearable device for runners to compare strictness of lockdowns and exercise habits, using digitally-logged PA data from more than 7,000 runners on a global scale. Additionally, time-of-day of PA globally and levels of PA in 14 countries are compared between the pre-pandemic year of 2019 and the first pandemic year of 2020. We found that during the pandemic the time-of-day that people exercised experienced a major shift, with significantly more activities logged during standard working hours on workdays (p<0.001) and fewer during the same time frame on weekends (p<0.001). Of the countries examined, Italy and Spain had among the most strict lockdowns and suffered the largest decreases in activity counts, whereas France experienced a minimal decrease in activity counts despite enacting a similarly strict lockdown. This study suggests that there are several factors affecting PA, including government policy, workplace policy, and cultural norms.

Chrysoeriol (CHE) is a flavonoid substance that exists in many plants and has various physiological and pharmacological effects, including anti-inflammatory, antioxidant, anti-tumor, and protective activity, especially for the cardiovascular system and liver. This study aimed to analyze the results and possible mechanisms of CHE on early porcine embryo development. Adding CHE to the culture media can improve the development quality of early porcine embryos. CHE significantly increased the blastocyst rate and total cell number of embryos in vitro. The apoptosis of blastocyst in CHE-treated culture also decreased significantly compared with untreated culture. Furthermore, CHE downregulated intracellular reactive oxygen species (ROS) and increased glutathione (GSH) in embryos. CHE was also shown to improve the activity of mitochondria and inhibit the occurrence of autophagy. In addition, antioxidant-related genes (SOD1, SOD2, and CAT) and cell pluripotency-related genes (SOX2, OCT4, and NANOG) were upregulated, while those related to apoptosis (Caspase 3) and autophagy (LC3B) showed a downward trend after supplementation with CHE. These results indicated that CHE improved the development of porcine embryos in vitro by reducing oxidative stress and autophagy levels.

Novel coronavirus infection is a recent infective agent that causes severe potentially fatal pneumonia. The clinical presentation includes asymptomatic infection, severe pneumonia, and acute respiratory failure. Data pertaining to the clinical presentation of solid organ transplant recipients are scarce. Two cases of novel coronavirus infection in two recipients of renal transplant with variable clinical presentations and outcomes are reported. The first patient presented with progressive respiratory symptoms, acute renal failure, and passed away, whereas the second one, although presented with respiratory tract symptoms and hypoxemia remained stable and exhibited an excellent clinical recovery despite recent reception of thymoglobulin induction. This paper reports rare cases of novel coronavirus infection in renal transplant recipients. For an enhanced insight of the novel coronavirus infection and acute kidney injury on the clinical presentation, severity, and outcome in solid organ transplant recipients, further investigations are required.

In the paper, by the Faά di Bruno formula, several identities for the Bell polynomials of the second kind, and an inversion theorem, the authors simplify coefficients of two families of nonlinear ordinary differential equations for the generating function of the Catalan numbers and discover inverses of fifteen closely related lower triangular integer matrices.

Evidence indicates that the long noncoding RNAs are involved in the metformin-mediated anti-cancer processes. However, the potential effects of the long noncoding RNAs in metformin-mediated anti-tumor processes in esophageal squamous cell carcinomas (ESCC) are still elusive. This study uncovered that metformin decreases the level of long noncoding RNAs CCAT1 and SPRY4-IT1 thereby contributing to the down-regulation of c-Myc and vimentin. Also, the RNA level test of human ESCC tissue confirmed the positive correlation between CCAT1 and c-Myc. These findings demonstrated that metformin facilitated anti-cancer effects by targeting the 2 long noncoding RNAs (CCAT1 and SPRY4-IT1) and their consequential targets c-Myc and vimentin. Therefore, the CCAT1 and SPRY4-IT1 might act as novel molecular targets that mediate the anti-tumor effects in esophageal squamous cell carcinoma. This helps in predicting the treatment response of metformin in patients diagnosed with esophageal squamous cell carcinoma.

This study extends the CGAN-based MODIS cloud vertical-profile (64×64-scene, about 70km width×15km height) retrieval technique developed by Leinonen et al. (2019) [1] to construct seamless 3D cloud fields for the MODIS granules [2]. Firstly, the accuracy and spatial continuity of the Leinonen et al. [1] retrievals are statistically evaluated. Then, according to the characteristics of the retrieval error, a spatially overlapping-scene ensemble generation method and a bi-directional Ensemble Binning Probability Fusion (CGAN-BEBPF) technique are developed, which improves the CGAN retrieval accuracy and support to construct seamless 3D clouds. The CGAN-BEBPF technique involves three steps: cloud masking, intensity scaling, and optimal value selection. It ensures adequate coverage of the low reflectivity areas while preserving the high reflectivity cloud cores. The technique is applied to retrieve the 3D cloud fields of Typhoon Chaba and a multi-cell convective system. The cloud structures of the CGAN-BEBPF results are highly consistent with the ground-based radar observations. It can retrieve weak clouds at the top levels of convective storms and hurricanes that were missed by ground-based radars and fill the gaps of the ground-based radar lower-level PPI scan. Overall, CGAN-BEBPF can be automated to retrieve the rich informative 3D structures of typhoons and severe convective systems over the oceans along the MODIS swath, which certainly presents great value for improving maritime and near-shore typhoons and convection prediction and other cloud-sensitive applications.

A typhoon-induced storm surge is considered one of the most severe coastal disasters in Taiwan. However, the combination of the storm surge and the astronomical tide called the storm tide can actually cause extreme flooding in coastal areas. This study implemented a two-dimensional hydrodynamic model to account for the interaction between tides and storm surges on the coast of Taiwan. The model was validated with observed water levels at Sauo Fish Port, Hualien Port, and Chenggong Fish Port under different historical typhoon events. The model results are in reasonable agreement with the measured data. The validated model was then used to evaluate the effects of the typhoon's intensity, bathymetric change, and the combination of the typhoon’s intensity and bathymetric change on the maximum storm tide and its distribution along the east coast of Taiwan. The results indicated that the maximum storm tide rises to 1.92 m under a typhoon with an intensity of a 100-year return period. The maximum storm tide increased from a baseline of 1.26 m to 2.63 m for a 90% bathymetric rise at Sauo Fish Port under the conditions of Typhoon Jangmi (2008). The combination of the intensity of a typhoon with a 100-year return period and a 90% bathymetric rise will result in a maximum storm tide exceeding 4 m, 2 m, and 3 m at Sauo Fish Port, Hualien Port, and Chenggong Fish Port, respectively. We also found that the distribution of the maximum storm tide on the east coast of Taiwan can expand significantly subject to the bathymetric rise.

Food waste is a common issue arising from grinding of food by experimental animals, leading to excessive food scraps falling into cages. In the wild, animals grind food by gnawing vegetation and seeds, potentially damaging the ecological environment. However, limited ecology studies have focused on food grinding behavior since the last century, with even fewer on rodent food grinding, particularly recently. Although food grinding function is partially understood, biological purposes remain under-investigated and driving factors unclear. This review aims to explain potential causes of animal food grinding, identify influencing factors, and discuss contexts and limitations. Specifically, we emphasize recent progress on gut microbiota significance for food grinding. Moreover, we show abnormal food grinding is determined by degree of excess normal behavior, emphasizing food grinding is not meaningless. Findings from this review promote comprehensive research on the myriad factors, multifaceted roles, and intricate evolution underlying food grinding behavior, benefiting laboratory animal husbandry and ecological environment protection, and identifying potential physiological benefits yet undiscovered.

Our skin is constantly exposed to blue light (BL), which is abundant in sunlight and emitted by digital devices. Prolonged exposure to BL can lead to oxidative stress-induced damages and skin hyperpigmentation. In this study, we investigated the protective effects of tocotrienol-rich fraction (TRF) on BL-induced oxidative stress and hyperpigmentation in B16-F1 melanocytes. Alpha-tocopherol (αTP) was used as a comparator. Our results showed that TRF effectively suppressed the formation of reactive oxygen species, and preserved the mitochondrial membrane potential. Additionally, TRF exhibited anti-apoptotic properties by reducing the activation of p38 mitogen-activated protein kinase molecule and downregulating the expression of cleaved caspase-3. Moreover, TRF modulated tyrosinase activity, resulting in a lowered rate of melanogenesis and reduced melanin production. In contrast, αTP did not exhibit the significant protective effects against skin damages and pigmentation in BL-induced B16-F1 cells. Therefore, this study indicates that TRF may offer superior protective effects over αTP against the effects of BL on melanocytes. These findings demonstrate the potential of TRF as a protective natural active against BL-induced skin damages and hyperpigmentation via its antioxidative and anti-melanogenic properties.

The time’s arrow of macroscopic physical phenomenon is reflected by irreversible physical process, which essentially occurs from small probability state to high probability state. In this paper, simplified models are proposed to understand the macroscopic physical process. In order to describe the information of a physical system, we defined the full self-information as "information height" to describe the complexity or difficulty of a macrostate of physical system. In this way, the direction of macroscopic physical process is from high information height to low information height. We can judge the direction of physical process by the information height. If we want the macroscopic physical process to evolve from the low information height state to the high information height state, the system need to add extra information and corresponding energy to increase the information height.

The fluorine-less noble-gas containing anions OBONgO- and OCNNgO-have been studied by correlated electronic structure calculation and density functional theory. The obtained energetics indicates that for Ng = Kr and Xe, these anions should be kinetically stable at low temperature. The molecular structures and electron density distribution suggests that these anions are stabilized by ion-induced dipole interactions with charges concentrated on the electronegative OBO and OCN groups. The current study shows that in additional to the fluoride ion, polyatomic groups with strong electronic affinities can also form stable noble-gas containing anions of the type X-...NgO.

Establishment of diagnostic methods with low detection limits plays a critical role in the maintenance of early diagnosis, prevention of serious neurological complications, and control of the spread of ZIKA. In this study, we established the micro-droplet digital polymerase chain reaction (ddPCR) and real-time fluorescent quantification PCR (qPCR) protocols for the detection of Zika virus based on the NS5 gene. For the Zika standard plasmid, the standard curve of R² was 0.999, and the amplification efficiency was 92.203%, as determined by qPCR. Both ddPCR and qPCR were positive for cell culture of Zika nucleic acid.The minimum detection limit of ddPCR is 1–2 times lower than qPCR. Moreover, all tests of Dengue virus (1–4 serotypes) were negative in cell culture. Overall, these results suggested than ddPCR may have a lower limit of detection than qPCR.

Food insecurity has adverse consequences on women and child health in a developing country. This study aims to fill the existing research gap by examining the dynamic impacts of food insecurity on women and child health outcomes, this study adds fresh large scale panel data; and unlike the existing studies, this study estimates the short-run dynamics on food insecurity on women as child health of developing countries. We found that there was a positive association between health expenditure, women's fertility rate, women, and child health outcomes. There was a negative and statistically significant impact of food insecurity on women anemia in developing countries of Asia. Overall, the empirical analysis found that there was a strong strength to be a negative correlation between food insecurity and women and child health outcome, particularly in relation to women’s participation as a productive labor force. The study suggests that there is need to multidimensional approaches such as women and child health outcome, is needed to advance this type of research areas and should be followed broad-spectrum policy interventions to improve the women and child health status as part of sustainable development goals.

Composite fiber materials are superior materials due to their high strength and light weight. Composites reflect the properties of their constituents, which is proportional to the volume fraction of each phase. There are different fiber reinforcement types and each affects it’s flexural, tensile and compression strength. When selecting a composite for a specific application, the forces excreted on the composite must be known in order to determine the reinforcement type. Unidirectional fiber reinforcement will allow very strong load resistance but only in one direction where as a random orientated fiber reinforcement can resist less load but can maintain this quota in all directions. These materials are said to be anisotropic. Certain composite fibers, taking into consideration there weights, are physically stronger than conventional metals. This research deals with the analysis of three composite materials with different reinforcement types, volume fraction and phase content. It was found that material A (glass epoxy) was the strongest in the longitudinal direction with a flexural strength of 534 MPa in the longitudinal and 420 MPa in the transverse direction. The flexural stresses of material B (glass silicone) and material C (glass polyester) where both found in the 120 to 135 MPa range. Differences were due to their differences in matrix composition and reinforcement type.

Proton exchange membrane water electrolyzers (PEMWEs) for water electrolysis have received tremendous attention due to their immediate response, high proton conductivity, low ohmic losses and gas crossover rate. However, design high activity, economical and long-term durable electrocatalysts in an acidic environment is still the bottleneck to realize the large-scale commercialization of PEMWEs. Iridium-based materials represent one of the most promising classes of oxygen evolution reaction (OER) catalysts due to their intrinsic stability in acid media over ruthenium-based counterparts. However, only a few innovative approaches have been developed to synthesizing iridium-based catalysts (IBCs) in the past decade, mainly due to achieving high activity may deteriorate the stability of IBCs. Accordingly, various engineering strategies of optimizing IBCs have been proposed to address this issue, including doping engineering, morphology engineering, crystal phase engineering and support engineering. Herein, a critical overview focusing on various synthesis and modulation strategies of IBCs is presented, based on an in-depth understanding of the relationship between electronic structures, charge redistribution and activity as well as stability of the electrocatalysts. In addition, the unprecedented achievements in PEMWEs are summarized. The reaction mechanisms and future perspectives are critically discussed to inspire more rational design of IBCs toward practical applications.

In mesoscale eddies, chemical properties and biological composition are different from those in surrounding water, due to their unique physical processes. It is unclear how physical-biological coupling occurs in warm-core eddies, particularly since no study has examined the relationship between bacteria and viruses. The purpose of the present study was to examine the influence of anticyclonic warm eddy on the relationship between bacterial and viral abundances as well as viral activity (viral production) in different depths. In the core of warm eddy, bacterial abundance (0.48 to 2.82 ×105 cells mL−1) fluctuated less than that of the outside eddy (1.12 to 7.03×105 cells mL−1). In particular, there was four-folds higher of viral-bacterial abundance ratio (VBR) estimated within the eddy below DCM than the outside eddy. We suggest that prevailing physical forces with downwelling at the center of the anticyclonic warm eddy, viruses can also be transmitted into the deep ocean directly through adsorption on particulate organic matter during sinking. Overall, our findings provide valuable insights into the interaction between bacterial and viral communities and their ecological mechanism within the warm eddy.

The continental shale layers are more complex in matrix pore-microfracture interactions and connectivity characteristics under the influence of tuff devitrification, which limits the explicit understanding of the coupling relationship between wettability and pore structure, as well as hydrocarbon flow behavior. Therefore, the influence of tuffaceous components on the reservoir formation mechanism and oil-rich effect of the continental shale formation system is a critical issue to be solved. The Upper Triassic Yanchang Formation tuffaceous shale in Ordos Basin and the Middle Permian Jingjingzigou Formation tuffaceous shale in the southern margin of Junggar Basin is taken as the research objects, using whole-rock mineral composition analysis, FE-SEM observation and digital image processing and extraction, as well as wettability angle determination and spontaneous imbibition experiments to illustrate the influence of the difference of devitrification extent on reservoir pore connectivity and interfacial wettability in two different environments of freshwater and saline lacustrine basins, and summarize the reservoir formation differential pattern under the influence of devitrification. The results show that the saline lacustrine is significantly modified by devitrification. The pore plane porosity of the devitrified tuffaceous shales in the saline lacustrine is higher than that of the tuffaceous shales in the freshwater; the oleophilic of the saline lacustrine tuffaceous shales is better than that of the tuffaceous shales in the freshwater, moreover, the pore connectivity of the saline lacustrine tuffaceous shales is better than that of the tuffaceous shales in the freshwater. Wettability and connectivity control the storage performance of shale oil in the tuffaceous shales formation system. The more oleophilic the reservoir wettability is, the better the pore connectivity is, and the better the reservoir of tuffaceous shale formation system is. According to the different extents of devitrification, two different reservoir formation models of freshwater and saline lacustrine are established, which are of great theoretical and practical significance to enrich the theory of shale oil enrichment and reservoir formation in the continental shale formation system and to guide the exploration of continental shale oil benefits.

Multi-rotor drones, a kind of unmanned equipment which is widely used in military, commercial consumption and other fields, has been developed very rapidly in recent years. However, their short flight time has hindered the expansion of their application range. This can be addressed by utilizing hydrogen fuel cells, which exhibit high energy density, strong adaptability to ambient temperature, and no pollution emissions, as the power source. Accordingly, the application of hydrogen fuel cells as the power source in multi-rotor drones is a promising technology that has attracted significant research attention. This paper summarizes the development process of hydrogen fuel cell mul-ti-rotor drones and analyzes the key obstacles that need to be addressed for the further development of hydrogen fuel cell multi-rotor drones, including structural lightweight, hydrogen storage methods, energy management strategies. Additionally, prospects for the future development of hydrogen fuel cell multi-rotor drones are presented.

To promote low-carbon and green travel, this study proposes a tripartite evolutionary game model among new energy vehicle manufacturers, consumers, and government agencies. The game strategy combinations of each party and the stability conditions of the equilibrium point in the evolutionary game system are analyzed, and the validity of the conclusions is verified through simulation results. The study shows a strong correlation between the three parties in the evolutionary game system. From the perspective of car manufacturers, the probability of producing new energy vehicles is positively proportional to the subsidy received from new energy policy, the additional revenue gained from the management of the carbon trading scheme, and the fine received for producing conventional fuel vehicles. However, from the consumer perspective, the likelihood that consumers purchase new energy vehicles is positively related to the utility value to consumers and the coverage of public charging points in the city, and inversely related to the sales price of new energy vehicles. From the government perspective, a combination of direct subsidy policies and indirect support strategies should be considered to stimulate the rapid development of the new energy vehicle industry.

This study aimed to present a systematic meta-analysis examining the association between Helicobacter pylori (H. pylori) infection, hemoglobin A1c levels, and the development of type 1 diabetes mellitus. The initial search identified 451 articles related to the association between H. pylori infection and T1DM. Among them, 14 articles had 2,971 participants meeting the inclusion criteria for advanced meta-analysis. A significant association was observed between H. pylori infection and T1DM, with an odds ratio (OR) of 1.87 (95% confidence interval [CI]: 1.27–2.78, p = 0.002). A subgroup analysis on H. pylori status showed that a longer duration of diabetes diagnosis and higher hemoglobin A1c levels were significantly associated with H. pylori infection (p < 0.001 for both). However, there was no significant association between H. pylori infection and the diagnostic age of diabetes (p = 0.306). These findings contribute to the understanding of the association between H. pylori infection and T1DM, thereby highlighting the potential role of H. pylori in influencing the duration and glycemic control of diabetes.

Amylin, also known as islet amyloid polypeptide (IAPP), is a metabolic homeostasis-related hormone that is produced and released by the β cells of the pancreas, the same cells that produce insulin. Insulin-degrading enzyme (IDE) is a protease enzyme that plays an essential role in the breakdown and degradation of various peptides, including insulin and amylin. Direct binding & interaction between amylin and IDE is inextricably linked to the degradation of amylin, and research and development effort in this area is crucial to understand the potential therapeutic implications of disrupting the IDE-amylin interaction in the context of conditions where metabolic homeostasis needs to be regulated, such as diabetes and obesity. Here, this article incorporates currently available experimental complex structure of amylin and IDE, and delves deep into the interstructural biophysics underlying the binding interface of the two interacting partners. With a set of comprehensive structural biophysical analysis, this article identified an intriguing region of high electrostatic potential indicative of strong binding sites between the first N-terminal lysine (Lys1, K1) residue of amylin and Glu341 (E341) of IDE. This unique electrostatic hotspot presented herein paves the way for the rational design of drug-like small molecules that can selectively disrupt this interaction, offering a targeted therapeutic strategy for improved metabolic homeostasis, particularly for patients with diabetes and obesity.

Parallax processing and structure preservation has long been important and challenging tasks in image stitching. In this paper, an image stitching method based on sliding camera to eliminate perspective deformation and asymmetric optical flow to solve parallax is proposed. By maintaining the viewpoint of two input images in the mosaic non-overlapping area and creating a virtual camera by interpolation in the overlapping area, the viewpoint is gradually transformed from one to another image view-point so as to complete the smooth transition of the two image viewpoints and reduce perspective deformation. Two coarsely aligned warped images are generated with the help of a global projection plane. After that, the optical flow propagation and gradient descent method are used to quickly calculate the bidirectional asymmetric optical flow between the two warped images, and the optical flow-based method is used to further align the two warped images to reduce parallax. In the image blending, the softmax function and registration error are used to adjust the width of the blending area, further eliminating ghosting and reduce parallax. Finally, the comparative experiments show that our method can effectively eliminate perspective deformation, reduce misalignment, and save running time.

The International Roughness Index (IRI) is the standard scale for evaluating road roughness in many countries in the world. The Taipei City government actively promotes a Road Smoothing Project and plans to complete the rehabilitation of the main and minor roads within its jurisdiction. This study aims to detect the road surface roughness in Taipei City and recommend appropriate IRI thresholds for road rehabilitation. A total of 171 asphalt concrete pavement sections in Taipei City with a total length of 803.49 km were analyzed and compared by IRI. The longitudinal profile of the detected road sections was measured using an inertial profiler. The statistical analysis showed that the IRI value prior to road leveling was mainly distributed between 5 and 8 m/km, while the IRI value after road leveling was mainly distributed between 3 and 4.5 m/km. This confirms that the implementation of the Road Smoothing Project has a significant effect on improving road smoothness. Moreover, based on the analysis results, it is recommended that the IRI threshold value for road rehabilitation in Taipei City be set at 4.50 m/km.

In the domain of drug discovery and design, the acquisition of precise structural and intermolecular Kd data for biological molecules is paramount. However, conventional methods for obtaining such data are often beset by challenges including high costs, time intensiveness, and inherent limitations in scalability and diversity. This article puts forward a high-throughput approach for in silico generation of structural and intermolecular binding affinity (Kd) data, which keeps exploring the uncharted territories of drug discovery & design by harnessing computational methodologies to synthetically generate diverse datasets. Through a meticulously designed workflow encompassing molecular structural modeling, structural biophysics-based calculations of intermolecular binding affinity (Kd), this innovative methodology transcends the constraints of traditional experimentation, offering a cost-effective, scalable, and efficient alternative. By simulating molecular interactions and binding interfaces and predicting binding affinities with reasonable accuracy, this approach not only expedites the drug development process but also enables the exploration of vast molecular space, thereby facilitating the discovery of novel therapeutics beyond conventional drug modality as a form factor. Moreover, the versatility of synthetic data extends beyond virtual screening and lead optimization, encompassing applications such as dataset augmentation, model validation, and benchmarking against experimental data. This article elucidates the conceptual underpinnings, methodological intricacies, validation strategies, and potential ramifications of in silico generated data, heralding a paradigm shift in drug discovery paradigms. By fostering synergy between computational and experimental research domains, this innovative approach promises to accelerate the pace of drug discovery, enhance the robustness of predictive models, and pave the way for transformative advancements in the entire pharmaceutical industry.

Sulfate attack is one of the main factors affecting the durability of concrete structures. In recent years, multi-walled carbon nanotubes (MWCNTs) have attracted the attention of scholars for their excellent mechanical properties and durability performance. In this paper, the influence of sulfate attack and dry-wet cycles on the performance of multi-walled carbon nanotube-lithium slag concrete (MWCNTs-LSC) with varied MWCNTs content (0wt%, 0.05wt%, 0.10wt% and 0.15wt%) and varied water-cement ratios (0.35, 0.40 and 0.45) were investigated. Besides, scanning electron microscopy (SEM) and X-ray computed tomography (CT) tests were conducted to analyze the microstructure and pore structure of the concrete. The results show that concrete incorporated with MWCNTs could effectively mitigate sulfate attack The resistance to sulfate attack of concrete is negatively related to the water-cement ratio when the dry-wet cycle is fixed. The MWCNTs-LSC showed the best compressive strength at the water-cement ratio of 0.35 and 0.10 wt% MWCNTs. The SEM test results showed that the MWCNTs both filled the pores and cracks within the specimen and formed bridges between the cracks, enhancing the resistance to sulfate attack. The CT test results also showed that the addition of MWCNTs could reduce the porosity of concrete, refine the pore size and inhibit the generation and development of cracks, thus optimizing the internal structure of concrete and improving its resistance to sulfate attack.

Pathogens, especially invasive species, have caused significant global ecological, economic, and social losses in forests. Plant disease research has traditionally focused on direct interactions between plants and pathogens in an appropriate environment. However, recent research indicates that the microbiome can interact with the plant host and pathogens to modulate plant resistance or pathogen pathogenicity, thereby altering the outcome of plant–pathogen interactions. Thus, this presents new opportunities for studying the microbial management of forest diseases. Compared to parallel studies on human and crop microbiomes, research into the forest tree microbiome and its critical role in forest disease progression has lagged. The rapid development of microbiome sequencing and analysis technologies has resulted in the rapid accumulation of a large body of evidence regarding the association between forest microbiomes and diseases. These data will aid the development of innovative, effective, and environmentally sustainable methods for the microbial management of forest diseases. Herein, we summarize the most recent findings on the dynamic structure and composition of forest tree microbiomes in belowground and aboveground plant tissues (i.e., rhizosphere, endosphere, and phyllosphere), as well as their pleiotropic impact on plant immunity and pathogen pathogenicity, highlighting representative examples of biological control agents used to modulate relevant tree microbiomes. Lastly, we discuss the potential application of forest tree microbiomes in disease control as well as their future prospects and challenges.

An eight-sided prism sample, obtained from a hot-rolled AZ31 magnesium alloy sheet, was compressed at room temperature along the transverse direction to investigate the influence of local strain on twinning behavior using electron backscatter diffraction (EBSD) measurements. The octagonal surface of the sample was divided into distinct regions based on hardness distribution and metallographic observations. The EBSD maps of different areas show significant variations, suggesting that these areas experienced different local strain conditions. The EBSD measurements provided detailed data from three distinct regions, with the strain state known in two regions and uncertain in the third. The combined analysis of the Schmid factor (SF) and the strain compatibility factor (m') was employed to study twin variant selection. The comparison of twinning behavior in different regions showed that the strain compatibility factor offered a more comprehensive explanation for the observed twinning pattern in the region with local shear strain.

A delayed crosslinked polymer gel was developed for indepth water control in mature oilfields. The thermal gelation behavior of nonionic polyacrylamide (NPAM) and PEI was investigated, and sodium citrate (NaCit) was selected as a new retarder to prolong the gelation time. The gelation performance of NPAM/PEI gel system can be adjusted by the variation of NPAM or PEI concentration, and a quadratic model was developed by statistical analysis, which predict the gelation time of NPAM/PEI gel system. The obtained model showed high significance and good reliability as suggested by the F-ratio of 175.16 and high adjusted R-square value (0.9732). The decrease of the initial pH value of gelling solution leads to the weaker gel viscosity and longer gelation time due to the protonation of amine groups on the PEI chains. Increasing temperature resulted in higher gel viscosity but shorter gelation time. The addition of NaCit showed a good delayed gelation effect on the NPAM/PEI gel system, and the gel system in the presence of NaCit exhibited a good compatibility with injected and formation water. A dense three-dimensional structure was observed in matured NPAM/PEI/NaCit gel, and it could keep stable below 150℃. The gel system could effectively reduce the permeability (>95%) and restricted the flow of water after matured in natural cores.

Since the launch of Protein Data Bank (PDB) in 1971, Cartesian coordinate system (CCS) has been the default approach to specify atomic positions in biomolecular experimental structures with X, Y and Z. In 2020, a local spherical coordinate system (LSCS) approach was proposed as an alternative to CCS, i.e., ρ, θ and φ. Recently, the continued application of deep learning technology in protein structure prediction (PSP) saw a leap forward in the accuracy of PSP, as evidenced by AlphaFold of Google’s DeepMind. However, there still is room for the improvement of the performances of PSP algorithms to date. Given that geometrically, CCS and LSCS are like the two sides of a coin, this short article puts forward a hypothesis that the time is now ripe to end the half-a-century burial of ρ, θ and φ in PDB, and use them as LSCS features for the design of novel PSP algorithms in future.

In agriculture, soil-borne fungal pathogens, especially Fusarium oxysporum strains, are posing a serious threat to efforts to achieve global food security. In the search for safer agrochemicals, silica nanoparticles (SiO2NPs) have recently been proposed as a new tool to alleviate pathogen damage including Fusarium wilt. Hollow mesoporous silica nanoparticles (HMSNs), a unique class of SiO2NPs, have been widely accepted as a desired pesticide carrier. However, their role in enhancing the disease resistance and the specific mechanism remain unknown. In this study, three sizes of HMSNs (19, 96 and 406 nm as HMSNs–19, HMSNs–96 and HMSNs–406, respectively) were synthesized and characterized to determine their effects on seed germination, seedling growth, and Fusarium oxysporum f. sp. phaseolus (FOP) suppression in cowpea roots by foliar spray using phenotypes, fresh biomass and disease progression as indicators. The results revealed that three HMSNs exhibited no adverse impacts on seed germination and tended to improve plant growth. Also, they exert their FOP suppression with a size- and concentration-dependent manner. HMSNs–406 possessed the best control effect at a concentration of 1000 mg/L showing an upto 40.00% decline in the disease severity. The Si(OH)4 control was also effective on FOP suppression at a lower concentration of 100 mg/L, whereas its higher concentrations exhibited obviously adverse impacts on FOP control, seed germination and plant growth. Moreover, we conformed that HMSNs posed their Fusarium wilt suppression in cowpea plant by activating SA (salicylic acid)-dependent SAR (systemic acquired resistance) responses rather than directly suppressing FOP. A higher level of SA content and elevated expression of its maker genes of PR-1 and PR-5 in HMSNs–406 treated cowpea roots provided substantial evidences of this mode of action. Other resistance-related genes, as well as defense-responsive enzymes, were also involved in the HMSNs-activated SAR pathway. Overall, for the first time, our results extended a new role of HMSNs as a potent elicitor to serve as a versatile alternative for plant disease protection of low cost, highly efficiency and sustainability.

A mild, efficient, and photocatalytic synthesis of 6-phosphorylated phenanthridines via tandem radical addition/cyclization/aromatization of 2-isocyanobiphenyls with diarylphosphine oxides is reported. The method features operational simplicity, metal-free conditions, using low-cost rose Bengal as catalyst and sustainable air as terminal oxidant at room temperature, and providing the desired products in moderate to good yields.

The Doppler band compensated by the keystone transform (KT) is limited. Therefore, it needs to be used in conjunction with the Doppler ambiguity compensation function to correct the range migration (RM) caused by maneuvering targets with Doppler ambiguity. However, the KT implemented by sinc interpolation suffers from significant performance loss at boundaries of compensation Doppler bands. Additionally, in a multi-target scenario, KT implementation methods occupy high complexity when the Doppler range of targets spans over two compensation Doppler bands. To address aforementioned issues, this study presents a variable Doppler starting point keystone transform (VDSPKT) method, where a new form of ambiguity compensation function is constructed, turning the Doppler starting point of the compensation band in KT variable. Firstly, the position of the compensation Doppler band is changed from fixed to adjustable as needed, enhancing the flexibility of KT. Crucially, the connection points of the compensation Doppler bands in sinc interpolation are reset, avoiding the performance loss at their boundaries. Also, the compensation band is adjusted to cover the narrow Doppler frequency range caused by targets, significantly improving the computational efficiency. Finally, the simulation results demonstrate that the proposed approach effectively addresses the performance degradation and high computational complexity of KT in the aforementioned scenarios, resulting in a computational load reduced by approximately 50% compared to traditional methods.

Aluminum wire is a common material for wire bonding due to its resistance to oxidation and low price. It does not melt when becoming a free air ball (FAB) during the electronic flame-off (EFO) process with wettability, and is applied by wedge bonding. This study used 20μm Zn-Coated Al-0.5wt.%Si (ZAS) wires to improve the FAB shape after the EFO process, while maintaining stability of the mechanical properties, including the interface bonding strength and hardness. In order to test circuit stability after ball bonding, the current-tensile test was performed. During the experiment, it was found that 80nm ZAS with wire bonding has lower resistance and higher fusing current. For the bias tensile test, the thicker Zn film diffused into the Al-Si matrix easily, after which the strength was reduced. The ball-bond interfaces had no change in their condition before and after the bias. Accordingly, ZAS could be a promising candidate for ball bonding in the future.

Infectious disease like COVID-19 will have a great impact on human society. An effective prevention and control measure is to quickly isolate the source and reduce the population’s exposure to the infection. Therefore, it is very important to quickly trace and identify the virus carrier and its close contacts in order to effectively suppressing transmission. This article provides a method, system and storage medium for locating the source of infection based on big data. We adopt the method of combining Bluetooth and GPS positioning to track the action trajectory of each individual. The method stores the close contact and location information locally and update on the cloud platform for an appropriate period of time. The method and system can provide personal risk levels and regional risk levels through related algorithms. When entering a high-risk area or if the personal risk level within the Bluetooth interconnection range is greater than the set threshold, an alarm function is provided. We can also generate reports on the spread of the epidemic over a period of time. As a result, the system can quickly locate the source of infection and close contacts, providing a reference for quick and highly efficient epidemic prevention and control.