Different inlet structures have a significant impact on the internal flow characteristics of a solid-magnesium powder water ramjet engine. Based on the magnesium-water reaction model, a computational fluid dynamics (CFD) method is applied to establish a numerical simulation method for the internal flow field of the engine, and the internal flow characteristics of the engine under different inlet structure conditions are studied. The simulation results show that high-temperature gas can effectively promote the ignition of magnesium powder at the top of the combustion chamber, while accelerating the evaporation of the first inlet water and increasing the combustion rate of magnesium powder. The secondary inlet has the most significant effect on the temperature inside the combustion chamber. When the secondary inlet flow rate increases towards the top of the combustion chamber, it increases the amount of heat absorbed by the evaporating water at the top of the chamber, thereby reducing the temperature at the top of the combustion chamber. However, when the flow rate is low, it results in insufficient oxidizer at the top of the combustion chamber, which is unfavorable for the combustion of magnesium powder.

Endoscopic retrograde cholangiopancreatography (ERCP) is a routinely used therapeutic procedure for the biliary and pancreatic diseases. Population aging may increase the typical indications of ERCP and come with more complexity and difficulties, especially in cannulation. This study aimed to evaluate the incidence, causes, and management of difficult biliary cannulation during ERCP in super-aged patients and the role of difficult cannulation as a risk factor for adverse events. A total of 614 patients, underwent ERCP, were prospectively studied as a cohort and divided into two groups based on their age. There were 146 patients aged 80 years or older in group A and 468 patients aged less than 80 years in group B. The primary outcome measures were the difficulty grade of papilla cannulation, clinical outcomes, and ERCP-related complications in the two groups. The adverse events were analyzed using logistic regression for patient age, co-morbidities, indications, and cannulation difficulty grade variables. There was no difference in the incidence of difficult cannulation between the two groups (32.9% vs. 34.4%, p=0.765) though, as expected, super-aged Group A had a higher prevalence of periampullary diverticulum (29.5% vs. 16.7%, p=0.001). The technical cannulation success rate was (96.6% vs. 96.8%, p= 0.54). All used cannulation techniques in the elderly group were efficient and safe. Logistic regression showed that age ≥80 was not associated with increased adverse events; however, difficult cannulation (adjusted odds ratio [AOR]=3.478; 95% confidence interval [CI]=1.877, 6.442; p<0.001) and CCI ≥2 (AOR=1.824; 95% CI=0.993, 3.349; p=0.045) were more likely to have adverse events. Age ≤65 (AOR=3.460; 95% CI=1.511, 7.922; p=0.003), female gender (AOR=2.362; 95% CI=1.089, 5.124; p=0.030), difficult cannulation (AOR=4.527; 95% CI=2.078, 9.860; p<0.001), and patients with cholangitis (AOR=3.261; 95% CI=1.204, 8.832; p=0.020) were strongly associated with increasing Post-ERCP Pancreatitis (PEP). Advanced age has not proved to be a risk factor of difficult cannulation, and secondary cannulation techniques can be safely and efficaciously utilized for this group. CCI ≥2 and difficult cannulation are associated with increased overall adverse events rate while age ≥80 factor is not.

In the overall context of national eco-conservation civilization development and considering the hills in the Beijing-Tianjin-Hebei-Shanxi region, the local forest coverage rate is gradually on the rise, and so is the risk of forest fire. Every year, satellites can monitor and detect hundreds of fire spots on average. In recent years, serious fire took place for several times, leading to loss of life and personal injury. Then the fire-fighting work consumed huge amount of labor and material resources, exerting negative social impacts in many ways. Thus, the analysis of fire climate background in this region and the forecast based on fire weather indexes constitute an important part in the forest fire risk management. Located in the tropical monsoon climate zone, four provinces and municipalities of Beijing, Tianjin, Hebei and Shanxi are similar in terms of climate characteristics. This study tries to analyze the characteristics about fire spots under satellite monitoring, fire climate and fire weather index. The probability distribution analysis of weather index about fire spots in history and key meteorological observation stations as well as the weather index analysis in the early stage of typical fire indicate that the Fine Fuel Moisture Content (FFMC) and the Initial Spread Index (ISI) in the Fire Weather Index (FWI) system is applicable to the fire risk analysis in the Beijing-Tianjin-Hebei-Shanxi region, which can also effectively indicate the fuel moisture and spread conditions. As regards to the average level in Beijing-Tianjin-Hebei-Shanxi, when the FFMC is smaller than 93.5 and the ISI is also smaller than 5.0, there is a low risk of fire; when the FFMC is above 94 and the ISI is larger than 10.0, there is a high risk of fire; and the fire risk will be extremely high if the FFMC is over 96 and the ISI is above 13.0. In the practical fire-fighting management, the fire danger class can be released in reference to the ISI classes and threshold values of key meteorological observation stations under analysis provided by this study.

The biomimetic design of engineering structures is based on biological structures with excellent mechanical properties, which are the result of billions of years of evolution. However, current biomimetic structures, such as ordered lattice materials, are still inferior to many biological materials in terms of structural complexity and mechanical properties. For example, the structure of \textit{Euplectella aspergillum}, a type of deep-sea glass sponge, is an eye-catching source of inspiration for biomimetic design; however, guided by scientific theory, how to engineer structures surpassing the mechanical properties of \textit{E. aspergillum} remains an unsolved problem. The lattice structure of the skeleton of \textit{E. aspergillum} consists of vertically, horizontally, and diagonally oriented struts, which provide superior strength and flexural resistance compared with the conventional square lattice structure. Herein, the structure of \textit{E. aspergillum} was investigated in detail, and by using the theory of elasticity, a lattice structure inspired by the bionic structure was proposed. The mechanical properties of the sponge-inspired lattice structure surpassed the sponge structure under a variety of loading conditions, and the excellent performance of this configuration was verified experimentally. The proposed lattice structure can greatly improve the mechanical properties of engineering structures, and it improves strength without much redundancy of material. This study achieved the first surpassing of the mechanical properties of an existing sponge-mimicking design. This design can be applied to lattice structures, truss systems, and metamaterial cells.

The process of shock wave focusing can make the strength of shock waves be continuously accumulated and turned into detonation wave in Pulse Detonation Engine (PDE). However, its effective application needs the inlet jets be in high temperature and velocity, which is difficult to be satisfied under certain conditions. Therefore, in this paper, metal magnesium assisted detonation initiation is proposed and the effect of magnesium particle addition on the shock wave focusing process in a kerosene-fueled PDE with cavity configuration is investigated through numerical simulation. The result showed that when the temperature of the premixed fuel/air jets injected in opposite direction was set as 650 K, the collision of leading shock waves on the central axis was the main source of energy deposition and the shock wave focusing could make the detonation be initiated in the cavity. When the temperature of jets is reduced to 550 K, fuel ignition and detonation could not be achieved through shock wave focusing. Then adding metal magnesium particles into the combustor made the energy deposition be enhanced and the detonation be induced. The diffusion of metal particles can significantly change the structure, motion, merging and dissipation of vortices in the flow field. Generally, the shock wave focusing process is basically not affected with metal particles injection. Therefore, this method can be successfully employed for detonation initiation in the cavity when the fuel/air premixed jet temperature is not high for PDE.

The paper discusses the classification of fuzzy metrics based on their continuity conditions, dividing them into Erceg, Deng, Yang-Shi, and Chen metrics. It explores the relationships between these types of fuzzy metrics, concluding that a Deng metric in [0,1]-topology must also be Erceg, Chen, and Yang-Shi metrics. The paper also proves that the product of countably many Deng pseudo-metric spaces remains a Deng pseudo-metric space, and demonstrates some σ-locally finite properties of Deng metric space. Additionally, the paper constructs two interrelated mappings based on normal space and concludes that if a [0,1]-topological space is T1 and regular, and its topology has a σ-locally finite base, then it is Deng metrizable, and thus Erceg, Yang-Shi, and Chen metrizable as well.

In the field of computer vision, large-scale image classification tasks are both important and highly challenging. With the ongoing advances in deep learning and optical character recognition (OCR) technologies, neural networks designed to perform large-scale classification play an essential role in facilitating OCR systems. In this study, we developed an automatic OCR system designed to identify up to 13,070 large-scale printed Chinese characters by using deep learning neural networks and fine-tuning techniques. The proposed framework comprises four components, including training dataset synthesis and background simulation, image preprocessing and data augmentation, the process of training the model, and transfer learning. The training data synthesis procedure is composed of a character font generation step and a background simulation process. Three background models are proposed to simulate the factors of the background noise and anti-counterfeiting patterns on ID cards. To expand the diversity of the synthesized training dataset, rotation and zooming data augmentation are applied. A massive dataset comprising more than 19.6 million images was thus created to accommodate the variations in the input images and improve the learning capacity of the CNN model. Subsequently, we modified the GoogLeNet neural architecture by replacing the FC layer with a global average pooling layer to avoid overfitting caused by a massive amount of training data. Consequently, the number of model parameters was reduced. Finally, we employed the transfer learning technique to further refine the CNN model using a small number of real data samples. Experimental results show that the overall recognition performance of the proposed approach is significantly better than that of prior methods and thus demonstrate the effectiveness of proposed framework, which exhibited a recognition accuracy as high as 99.39% on the constructed real ID card dataset.

This study utilises NaOH to treat composite cementitious materials containing aeolian sand and zeolite powders, which were used to replace 50% of the cement in aeolian-sand concrete (ASC). The mechanical properties of treated ASC considerably improved, especially when the NaOH dosage was 4% by mass. After curing this sample (denoted as AAZC-4) for 28 d, its compressive strength improved by 17.2% and its split tensile was increased by 16.3%. Potassium feldspar and montmorillonite in zeolite powder and SiO2 in the sand were decomposed by OH− and combined with other elements to generate various silicate gels and A-type potassium zeolite crystals inside the concrete. Microscopic examination showed that the gels and crystals intertwined to fill the pores, decreasing (increasing) the percentage of large (small) pores, thus optimising the pore structure. This substantially improved the mechanical properties of ASC. Freeze–thaw salt-intrusion tests showed that the extent of mass loss, degree of damage and loss of compressive strength of AAZC-4 were similar to those of ordinary concrete but were reduced by 36.8%, 19% and 52.1%, respectively, compared with those of ASC. Therefore, AAZC-4 has sustainable working performance in the chloride ion permeable environment in cold and arid areas.

This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

Information encryption and anti-counterfeiting play an important role in many aspects of daily life, such as in minimizing economic losses, protecting secure communication and public security, and so on. Owing to the high information capacity and ease of operation, luminescent materials for advanced information encryption and anti-counterfeiting are essential to meet the increasing demand on encryption security. Herein, we summarize two emerging luminescent materials for information encryption and anti-counterfeiting, the AIE materials and room-temperature phosphorescent materials. At last, we discuss the opportunities and anticipations of these two information encryption and anti-counterfeiting materials.

Vip3 proteins are increasingly used in insect control in transgenic crops. To shed light on the structure of these proteins, we used the approach of trypsin fragmentation of mutants altering the conformation of the Vip3Af protein. From an alanine scanning on Vip3Af, we selected mutants with an altered proteolytic pattern. Based on the protease digestion patterns, their effect on oligomer formation, and theoretical cleavage sites, we generated a map of the Vip3Af protein with five domains, which match some of the domains proposed independently by two in silico models. Domain I ranges from aa12-198, domain II from aa199-313, domain III from aa314-526, domain IV from aa527-668 and domain V from aa669-788. The effect of some of the mutations on the ability to form a tetrameric molecule revealed that domains I-III are required for tetramerization, while domain V is not. The involvement of domain IV in the tetramer formation is not clear. Some mutations distributed from near the end of domain I up to the end of domain II affect the stability of the first three domains of the protein and negatively impact oligomerization upon trypsin treatment. Because of the high sequence similarity among Vip3 proteins, we propose that our domain map can be extended to many other members of the Vip3 family of proteins.

Aberrant neutrophil extracellular trap (NET) formation and the loss of barrier integrity in inflamed intestinal tissues have long been associated with inflammatory bowel disease (IBD). However, whether NETs alter intestinal epithelium permeability during colitis remains elusive. Here, we demonstrated that NETs promote the breakdown in intestinal barrier function for the pathogenesis of intestinal inflammation in mouse models of colitis. NETs were abundant in the colon of mice with colitis experimentally induced by dextran sulfate sodium (DSS) or 2,4,6-trinitrobenzene sulfonic acid (TNBS). Analysis of the intestinal barrier integrity revealed that NETs impaired gut permeability, enabling the initiation of luminal bacterial translocation and inflammation. Furthermore, NETs induced the apoptosis of epithelial cells and disrupted the integrity of tight junctions and adherens junctions. Intravenous administration of DNase I, an enzyme that dissolves the web-like DNA filaments of NETs, during colitis restored the mucosal barrier integrity which reduced the dissemination of luminal bacteria, and attenuated intestinal inflammation in both DSS and TNBS models. We conclude that NETs serve a detrimental factor in the gut epithelial barrier function leading to the pathogenesis of mucosal inflammation during acute colitis.

The estimation of ecological service system value of water resources in Tarim river basin is of great significance for resource allocation management and ecological protection. However, there is still no unified and complete evaluation method for ecological service system value of inland river in China. Based on the perspective of the whole value chain, the study classifies its ecological service functions, and divides 11 sub-categories into 4 categories (supply, regulation, culture and support) as evaluation indicators to carry out quantitative evaluation. The results showed that the total value of ecological service system in Tarim river basin in 2018 was 4156.5247×108 Yuan, and the value of regulating function, cultural function, supporting function and supply function were successively from high to low, which were as follows: 2565.6825×108 Yuan, 1009.5471×108 Yuan, 884.0770×108 Yuan, 20.3350×108 Yuan, among which the value of regulation function is dominant.

Viruses can infect a cell via one or both routes viz. cell-to-cell (c-c) or cell-free (c-f) . Pathogenesis studies of various viruses, including HIV, have shown that c-c transmission yields a significantly higher infection magnitude than the c-f route. Expectedly, potent antibodies inhibited c-f infection more efficiently than with c-cell transmission. To achieve a one-step, synchronous infection cycle that provides amplified infection, we have studied a consistent and efficient c-c HIV infection model since 1992. H9 cells persistently infected with HTLV-IIIB (H3B cells) and uninfected target CD4+ lymphocyte line (HuT78) were mixed in a ratio of 1:4 respectively. We have recently used this model to produce HIV designer antigens that have been shown to elicit monoclonal as well as polyclonal specific antibodies against novel epitopes that are formed post virus-cell engagement, but prior to fusion. The model can be extended for HIV neutralizing antibody assays or drug inhibitors against high multiplicity of infection.

：An effective technology for predicting the end-point phosphorous content of basic oxygen furnace (BOF) can provide theoretical instruction to improve the quality of steel via controlling the hardness and toughness. Given the slightly inadequate prediction accuracy in the existing prediction model, a novel hybrid method was suggested to more accurately predict the end-point phosphorus content by integrating an enhanced sparrow search algorithm (ESSA) and a multi-strategy with a deep extreme learning machine (DELM) as ESSA-DELM in this study. To begin with, the input weights and hidden biases of DELM were randomly selected, resulting in that DELM inevitably had a set of non-optimal or unnecessary weights and biases. Therefore, the ESSA was used to optimize the DELM in this work. For the ESSA, the Trigonometric substitution mechanism and Cauchy mutation were introduced to avoid trapping in local optima and improve the global exploration capacity in SSA. Finally, to evaluate the prediction efficiency of ESSSA-DELM, the proposed model was tested on process data of the converter from the Baogang steel plant. The efficacy of ESSA-DELM was more superior to that of other DELM-based hybrid prediction models and conventional models. The result demonstrated that the hit rate of end-point phosphorus content within ±0.003%, ±0.002%, and ±0.001% was 91.67%, 83.33%, and 63.55%, respectively. The proposed ESSA-DELM model could possess better prediction accuracy compared with other models, which could guide field operations.

Although crop conversion from annual to perennial crops has been considered as one path towards climate-smart and resource-efficient agriculture, the effects of this conversion on soil multifunctionality and biomass yields remain unclear. Here, we investigated the effects of one annual and three perennial crops (a grass (Lolium perenne), a legume (Medicago sativa), and their mixture) on soil multifunctionality and biomass yield on the Yellow River floodplain. Soil multifunctionality was assessed by the capacity of water regulation and the multifunctionality of carbon (C), nitrogen (N), and phosphorus (P) cycles. Results showed that perennial crops enhanced soil multifunctionality by 207% for L. perenne, 311% for M. sativa, and 438% for L. perenne + M. sativa, compared with annual winter wheat (Triticum aestivum). The effect of perennial crops on soil multifunctionality increased with infiltration rate, dissolved organic C, microbial biomass C, and extracellular enzymatic activities for both C and N acquisition. However, we observed that perennial crops had lower biomass yield than annual crop. Therefore, the transition of agricultural landscapes to perennials needs to take into account the balance between environmental protection and food security, as well as environmental heterogeneity, to promote sustainable agricultural development.

In recent years, there has been significant growth in the ubiquity and popularity of three dimensional(3D) point clouds, with an increasing focus on the classification of 3D point clouds. To extract richer features from point clouds, many researchers have turned their attention to various point set regions and channels within irregular point clouds. However, this approach has limited capability in attending to crucial regions of interest in 3D point clouds and may overlook valuable information from neighboring features during feature aggregation. Therefore, this paper proposes a novel 3D point cloud classification method based on global attention and adaptive graph convolution. The method consists of two main branches: the first branch com-putes attention masks for each point, while the second branch employs adaptive graph convolu-tion to extract global features from the point set. It dynamically learns features based on point interactions, generating adaptive kernels to effectively and precisely capture diverse relationships among points from different semantic parts. Experimental results demonstrate that the proposed model achieves 93.8% in overall accuracy and 90.8% in average accuracy on the ModeNet40 dataset.

One new cassane diterpene possessing an unusual N bridge between C-19 and C-20 named caesalsappanin R (1), as well as another new diterpene caesalsappanin S (2), were isolated from the seeds of Caesalpinia sappan with methanol extract. Their structures were determined by spectroscopic analysis and examined alongside existing data from prior studies. Their biological activities were profiled by their antiplasmodial activity.

Research on the development of new lightweight Al-Li alloys using selective laser melting pro-cess has great potential for industrial applications. This paper reports on the development of novel aluminum-lithium alloys using selective laser melting technology. Al-Cu-Li-Mg-Ag-Sc-Zr pre-alloyed powders with lithium contents of 1 wt.%, 2 wt.% and 3 wt.%, respectively, were prepared by inert gas atomization. After SLM process optimization, the microstructure and me-chanical properties of the as-formed specimens were investigated. The densification of the three newly developed alloys are 99.51 %, 98.96 % and 92.01 %, respectively. They all have good form-ability, with the lithium loss rate about 15 %. The as-formed alloy with 1% Li content presents good comprehensive properties with a yield strength of 412.6 ± 16.0 MPa, an ultimate tensile strength of 461.1 ± 11.7 MPa, and an elongation of 13.6 ± 1.1%. The three alloys exhibit a layered molten pool stacking morphology and have a typical heterostructure. The columnar crystals and equiaxed fine grains are alternately arranged, and most of the precipitated phases are enriched at the grain boundaries. The change of Li content mainly affects the precipitation of Cu-containing phase. When the Li content is 1 wt.%, there are θ phase, T1 phase and TB phase. When Li increased to 2 wt.%, T1 and T2 phases precipitated together. When Li reaches 3 wt.%, δ' phase precipitates with T2 phase. This study provides useful guidance for the future SLM form-ing of new crack-free and high-strength Al-Li alloys.

Star image registration is the most important step in the application of astronomical image differencing, stacking and mosaicking, which requires high robustness, accuracy and real--time of the algorithm, but there is no high--performance registration algorithm in this field. In this paper, we propose a star image registration algorithm that relies only on radial module features (RMF) and rotation angle features (RAF), which has excellent robustness, high accuracy, and good real--time performance. The test results on a large amount of simulated and real data show that the comprehensive performance of the proposed algorithm is significantly better than the four classical baseline algorithms in the presence of rotation, insufficient overlapping area, false stars, position deviation, magnitude deviation and complex sky background, which is a more ideal star image registration algorithm.

Reasonable allocation of production plans and saving the overall electricity cost are crucial for large manufacturing conglomerates, which is an effective way for conglomerates to realize open-source and cost-saving. This paper develops an optimization model of off-site industrial production scheduling for enterprises in response to the problems of high electricity costs due to the irrational allocation of production schedules on the demand side of China's electric power and the difficulty of promoting industrial and commercial distributed photovoltaic (PV) projects in China. The model makes full use of the conditions of different PV resources and different electricity prices in different places to optimize the scheduling of industrial production in different places. The model is embedded with two sub-models of the electricity price prediction model and distributed photovoltaic kWh cost model to complete the model parameters, in which the electricity price prediction model utilizes the LSTM neural network. The integrated model is then solved by the particle swarm algorithm. To verify the effectiveness of the model in solving the problem of off-site production scheduling on the demand side of electricity, the research team researched two off-site pharmaceutical factories belonging to the same large pharmaceutical company. Finally, the research data were substituted into the model for solving, and it was concluded that the optimization model could significantly reduce the cost of electricity consumption of the enterprise by about 7.9 %.

Transcription factors (TFs) in the homeodomain-leucine zipper (HD-ZIP) family serve as essential regulators of plant development and control responses to environmental stimuli. To date, however, the HD-ZIP gene family in Prunus nana remains to be fully characterized. Accordingly, a genome-wide analysis of P. nana HD-ZIP family genes was performed using the most recent genomic data available, leading to the classification of 30 HD-ZIP TFs. These genes were annotated and subjected to systematic analyses of phylogenetic relationships, protein physicochemical properties, sequence-based structural characteristics, chromosomal distributions, and associated cis-acting regulatory elements. High levels of diversity were observed with respect to the gene structures for these PnaHD-Zip genes and the cis-regulatory elements found in the promoter regions upstream of these genes, suggesting that they play diverse roles in a range of biological contexts. These 30 PnaHD-Zip genes were further classified into four subgroups based on the results of phylogenetic, gene structure, and conserved motif analyses. Subsequent qPCR analyses indicated that PnaHD-Zip1 and PnaHD-Zip7 expression levels tended to increase was continuously inhibited in response to cold stress, suggesting that proteins in this HD-ZIP gene family may exhibit distinct responses to low-temperature stress exposure. Overall, these results offer a robust foundation for future studies seeking to explore the functional roles that HD-ZIP TFs play as regulators of cold stress tolerance in P. nana, in addition to offering more general insight regarding the regulatory functions and characteristics of these different HD-ZIP genes in P. nana.

China promotes nature-based solutions (NbS) as key approaches to addressing climate change, ecosystem damage, and biodiversity loss. However, indigenous and local knowledge (ILK), which is recognized by international scholars as an essential element of successful NbS, has not been thoroughly studied in the Chinese context. By conducting a comprehensive review of Chinese central governmental policies and semi-structured interviews with typical cases, this study finds out diversified sources of ILK and five pathways of ILK integration, including education, supervision, participation, knowledge preservation, and knowledge adoption. An increasing emphasis on community engagement has been driven by central policies such as the ecological civilization, carbon peaking and carbon neutrality goals. From a practical perspective, consistent core ideas of ILK exist in selected typical Chinese cases and studies in other countries, namely co-existence and reciprocity with nature. While supportive central policies can set the scene, ILK integration could not be realized without local governmental endorsement, context-based implementation, and long-term multi-stakeholder participation. Furthermore, this study also figures out a potential deficiency in terms of realizing effective ILK integration in mainstream and conventional practices, which can be further investigated by future studies.

In an effort to enhance the efficiency and safety of open-pit mines, this study explores the optimization of end slope road parameters and slope structures, specifically focusing on unmanned driving lanes.A significant aspect of the study is the development of a truck trajectory offset model, which considers the different reaction times between automated sensors and human drivers in adapting to environmental changes. To test these concepts, the study uses numerical simulations to confirm the stability of the proposed end slope designs. Using Victory West Mine No. 1 as a case study, the research determines the optimized width for unmanned driving lanes and the maximum angle for safe steepening of end slopes. The findings indicate that the optimized unmanned lane width for NTE240 mining dump trucks is 1743 mm, allowing for a 2-degree increase in the slope angle at the south end slope. This optimization leads to a steep mining stripping volume of 3.2735 million m³ and a coal output of 2.49628 million tons, maintaining a stripping ratio of 1.31m³/t. These results demonstrate that the unmanned driving road width optimization not only ensures slope safety but also significantly boosts the economic benefits of steep mining in open-pit mines.

Flux-switching permanent magnet (FSPM) motors have gained increasing attention in the electric vehicles (EVs) applications due to the advantages of high power density, high efficiency. However, the heat sources of both permanent magnet (PM) and armature winding are located on the limited stator space in the FSPM motors, which may result in the PM overheated and irreversible demagnetization caused by temperature rise and it is often ignored in the conventional thermal analysis. In this paper, a new electrical-thermal two-way coupling design method is proposed to analyze the electromagnetic performances, where the change of PM material characteristics under different temperatures is taken into consideration. Firstly, the motor topology and design equations are introduced. Secondly, the demagnetization curves of PM materials under different temperatures are modeled due to PM materials are sensitive to the temperature. And based on the electrical-thermal two-way coupling method, the motor performances are evaluated in details, such as the load PM flux linkage and output torque. Then, the motor is optimized, and the electromagnetic performances between initial and improved motors are compared. Finally, a prototype motor is manufactured, and the results are validated by experimental measurements.

Lithium rich layered oxides (LRLO) are a wide class of innovative active materials for positive electrodes in lithium-ion (LIB) and lithium-metal secondary batteries (LMB). LRLOs are over-stoichiometric layered oxides rich in lithium and manganese, with general formula Li1+xTM1-xO2, where TM is a blend of transition metals comprising Mn (main constituent), Ni, Co, Fe and others. Due to the very variable composition and the extended defectivity their structural identity is still debated among researchers being likely an unresolved hybrid between a monoclinic (mC24) and a hexagonal lattice (hR12). Once casted in composite positive electrode films and assembled in LIBs or LMBs, LRLOs can delivery reversible specific capacities above 220-240 mAhg-1, thus beyond any other available intercalation cathode material for LIBs, with mean working potential above 3.3-3.4 V vs Li for hundreds of cycles in liquid aprotic commercial electrodes. In this review we critically outline the recent advancements in the fundamental understanding of the physico-chemical properties of LRLO as well as the most exciting innovations in their battery performance. We focus in particular on the elusive structural identity of these phases, on the complexity of the reaction mechanism in batteries as well as on practical strategies to minimize or remove cobalt from the lattice while preserving the outstanding performance upon cycling.

This study was conducted to determine the dynamic effects of dietary crude protein (CP) intake on nitrogen (N) balance, ileal amino acid digestibility, and gene expression levels of digestive enzymes at three stages in pigs. In Experiment 1, 18 growing pigs (average body weight (BW) = 9.5 kg) were randomly assigned to one of three treatments (n = 6/treatment group), including normal (20% CP), low (17% CP), and very low (14% CP) protein intake. In Experiment 2, 18 growing pigs (average BW = 30 kg) were allotted randomly to one of three treatments (n = 6/treatment group), including normal (18% CP), low (15% CP), and very low (12% CP) protein intake. In Experiment 3, 18 growing pigs (average BW = 45 kg) were assigned randomly to one of three treatments (n = 6/treatment group), including normal (16% CP), low (13% CP), and very low (10% CP) protein intake. Growing pigs fed the 14% CP and 17% CP diets had lower final BW (P < 0.05) and average daily gain (ADG) (P < 0.05) compared to pigs fed the 20% CP diet. Reducing the dietary CP level from 20 to 14% decreased urinary N excretion by 52.8% (P < 0.001) in Experiment 1. Reducing the dietary CP level from 18 to 12% decreased urinary N excretion by 55.3% (P < 0.001) and reduced fecal N excretion by 34% (P < 0.05) in Experiment 2. Reducing the dietary CP level from 16 to 10% decreased urinary N excretion by 56.4% (P < 0.001) and fecal N excretion by 47.1% (P < 0.001) in Experiment 3. Pigs fed the very low (14%, 12%, and 10% CP) diets showed higher digestibility for CP (P < 0.05), His (P < 0.05), Ile (P < 0.05), Phe (P < 0.05), Thr (P < 0.05), Trp (P < 0.05), Glu (P < 0.05), and Ser (P < 0.05) compared to pigs fed the normal (20%, 18%, and 16% CP) diets among the three experiments. Pigs fed the very low (14%, 12%, and 10% CP) diets showed higher mRNA levels for chymotrypsin C (P < 0.01 in Experiment 1 and 2; P < 0.05 in Experiment 3) compared to pigs fed the normal (20%, 18%, and 16% CP) diets among the three experiments. These results indicated that a reduction in dietary CP by 6% limited the growth performance of growing pigs, and a reduction of dietary CP by 3% supplemented with essential amino acids could reduce the excretion of N into the environment without affecting weight gain.

Examining the soil microbiome structure has a great significance in exploring the mechanism behind plant growth changes due to maize (Zea mays L.) and soybean (Glycine max Merr.) crop rotation. This study explored the effects of soil microbial community structure after soybean and maize crop rotation by designing nine treatments combining three crop rotations (continuous cropping maize or soybean; and maize after soybean) with three fertility treatments (organic compound fertilizer, chemical fertilizer, or without fertilizer). Soil was sampled to 30 cm depth the second year at approximately the middle of the growing season, and was analyzed for physical, chemical, and phospholipid fatty acid (PLFA) profiles. Bacteria was found to be the predominant component of soil microorganisms, which mainly contain the PLFAs i15:0, 16:1 ω 7c, 16:0, 10Me16:0, and 18:1 ω 7c. The concentration of soil gram-negative bacteria from the soybean and maize rotation was less than in soybean continuous cropping when organic fertilizer was applied to both. Crop rotation reduced the percentage of fungi in the soil, among which the effect of organic compound fertilizer application was significantly reduced 24%. The combined crop rotation with organic fertilizer can reduce maximum the percentage of fungi/bacteria. In addition, the content of soil aggregate and organic matter had great influence on gram-positive bacteria and actinomyces, and soil pH had a greater impact on other fungi.

With the development of electricity spot markets, accurate electricity load forecasting enables power generation companies to supply the right amount of electricity, Significantly avoid power waste. As a result, time series forecasting in the field of power can bring significant benefits. Previously, the Informer model successfully introduced the Transformer into long time series forecasting(LTSF) by proposing the ProbSparse self-attention mechanism, which solved the inherent problem of high memory complexity in self-attention. Recent research has further demonstrated the potential of the self-attention for mining complex dependencies. However, the limited amount of historical data has become one of the main challenges in applying deep learning techniques to power LSTF tasks. Previous reserches often add a large number of time covariates to provide more information. In this paper, to address this issue, (i) we design a simple but effective Season-aware Block to enhance the model’s ability to mine artificial prior information in temporal covariates; (ii) we conduct experiments using the provincial power data of Zhejiang Province, China, from 2019 to 2022, and our model outperforms other models, achieving a 19 percent MSE relative improvement; (iii) we conduct ablation experiments to assess the efficacy of the Season-aware Block in extracting temporal periodic features. Furthermore, we elucidate the underlying reasons for the effectiveness of both the self-attention mechanism and the Season-aware Block through visualization experiments.

The construction safety risks (such as landslides or slumps) of the high-fill subgrade are characterized by uncertainty and variability. In order to ensure the construction safety of the high-fill subgrade of the expressway, a comprehensive risk assessment model of high-fill subgrade construction according to the combination weighting method based on game theory was established. Firstly, settlement rate, lateral differential settlement, horizontal displacement at the foot of the slope, deep horizontal displacement, and excess pore pressure were selected as evaluation indicators, and an evaluation index system of high-fill subgrade was constructed. Secondly, the subjective and objective weights were obtained via the analytic hierarchy process and entropy method. Furthermore, the optimized weights were obtained by introducing game theory, and the construction risk of the high-fill subgrade was evaluated and analyzed using the fuzzy comprehensive evaluation method. Finally, based on the high-fill section of the Zhijiang-Tongren Expressway in Hunan Province (China), the evaluation model was validated through field measurement data. The results show that the safety scores obtained using the three methods of analytic hierarchy process, entropy method, and combination weighting method based on game theory are similar. The combination weighting evaluation model can correct the evaluation result error caused by a single weight and avoid information delay caused by the manual processing and analysis of monitoring data. The high-fill subgrade safety evaluation grade based on the combination weighting method and game theory is consistent with the engineering situation, and its fault tolerance range is within 20%. The evaluation model proposed in this study can scientifically and effectively evaluate the safety risks of high-fill subgrade construction, significantly improving the safety and reliability during the construction process.

As a representative of Exponential Organizations, MI went from obscurity to the Fortune 500 in just ten years. Mi's success is inextricably linked to its outstanding business model. This paper summarizes the elements of MI's business model from four perspectives: value proposition, value creation, value delivery, and value capture, as well as its measures for developing into an exponential organization. Expecting to provide theoretical references for the transformation and upgrading of manufacturing organizations.

Ship detection in large-scene offshore synthetic aperture radar (SAR) images is crucial in civil and military fields, such as maritime management and wartime reconnaissance. However, the problems of low detection rates, high false alarm rates, and high missed detection rates of offshore ship targets in large-scene SAR images are due to the occlusion of objects or mutual occlusion among targets, especially for small ship targets. To solve this problem, this study proposes a target detection model (TAC_CSAC_Net) that incorporates a multi-attention mechanism for detecting marine vessels in large-scene SAR images. Experiments were conducted on two public datasets, the SAR-Ship-Dataset and high-resolution SAR image dataset (HRSID), with multi-scene and multi-size, and the results showed that the proposed TAC_CSAC_Net model achieves good performance for both small and occluded target detection. Experiments were conducted on a real large-scene dataset, LS-SSDD, to obtain the detection results of subgraphs of the same scene. Quantitative comparisons were made with classical and recently developed deep learning models, and the experiments demonstrated that the proposed model outperformed other models for large-scene SAR image target detection.

A complete MAPLE procedure is designed to implement effectively an algorithm for approximating the trigonometric functions. The algorithm gives a piecewise polynomial approximation on an arbitrary interval, presenting a special partition that we can get its parts, subintervals with ending points of finite rational numbers, together with corresponding approximate polynomials. The procedure takes a sequence of pairs of interval-polynomial as its output that we can easily explore in some useful ways. Examples on calculating approximate values of the sine function with arbitrary accuracy for both of rational and irrational arguments as well as drawing the graph of the piecewise approximate functions will be presented. Moreover, from the approximate integration of integrands of the form $x^m\sin x$ on $[a,b]$, another MAPLE procedure is proposed to find the desired polynomial estimates in norm for the best $L^2$-approximation of the sine function in the vector space $\mathcal{P}_{\ell}$ of polynomials of degree at most $\ell$, a subspace of $L^2(a,b)$.

With an increase in energy consumption globally, Fischer-Tropsch (FT) synthesis is a good alternative for producing fuels and chemicals from coal, natural gas or biomass. Among them, coal to liquids has been put into production in countries that have large coal reserves. In this process, Fe-based catalysts are commonly used due to their earth abundance, comparatively wide operation range and ready availability to handle low H2/CO ratio from coal. Despite their extensive applications, the kinetic and mechanistic understandings of Fe carburization and FT reaction on Fe-carbides are relatively limited due to the complexity of phase composition of the applied catalysts. This review summarizes the current state of knowledge of FT synthesis on Fe-carbide with an emphasis on underlying mechanism. Specifically, the employment of model catalyst, such as Raney-Fe, could provide a convenient way to furnish kinetic information regarding Fe carburization and subsequent FT reaction. A major challenge for further understanding catalytic reactions occurring at the Fe-carbide surface is correlating FT activity and selectivity to specific active site. To address this issue, the advancements of both DFT calculations and surface science techniques are highly demanded.

The application of movement-detection sensors is crucial for understanding surface movement and tectonic activities. The development of modern sensors has been instrumental in earthquake monitoring, prediction, early warning, emergency commanding and communication, search and rescue, and life detection. There are numerous sensors currently being utilized in earthquake engineering and science. It is essential to review their mechanisms and working principles thoroughly. Hence, we have attempted to review the development and application of these sensors by classifying them based on the timeline of earthquakes, physical or chemical mechanisms of sensors, and location of sensor platforms. In this study, we analyzed all available sensor platforms that have been widely used in recent years, with satellites and UAVs being among the most used. The findings of our study will be useful for future earthquake response and relief efforts, as well as research aimed at reducing earthquake disaster risks.

This paper studies the integrated design problems of control and guidance with parameter uncertainties, target disturbances, input constraints and actuator faults. Firstly, based on the integrated design idea of the missile guidance and control, the auxiliary variable is used to establish and transform it into a cascade system with input constraints, actuator faults and disturbances of unknown upper bounds. Secondly, the adaptive anti-saturation dynamic surface fault-tolerant controller is designed by using the back-stepping method, adaptive control, auxiliary system and tracking differentiator. By introducing the tracking differentiator and tangent barrier Lyapunov function, the computational explosion problem in the traditional back-stepping method is avoided and the angle of attack can be guaranteed in prospective range, respectively. Finally, the theoretical proof of the designed control strategy is given to ensure that the states of the closed-loop system are bounded. At the same time, the digital simulation of the maneuvering target of different maneuvering forms is carried out, which further illustrate the effectiveness and robustness of the designed control schemes.

Barnyardgrass (Echinochloa spp.) is a prevalent type of weed in rice fields worldwide. Despite the growing knowledge concerning allelopathic interference with barnyardgrass, little is understood regarding the competitive mechanisms between allelopathic rice and herbicide-resistant barnyardgrass at the plant physiological level. In this context, a hydroponic system was employed to investigate the root morphological traits and different phytohormones levels of two rice cultivars, i.e., the allelopathic rice cultivar “PI312777” (PI) and the non-allelopathic rice cultivar “Lemont” (LE), when co-planted with quinclorac-resistant and -susceptible barnyardgrass, respectively. The results showed that the shoot and root biomass were greater in the allelopathic rice cultivar. Moreover, the treatments at the two time points induced an increase in shoot and root biomass of PI when subjected to barnyardgrass stress. In terms of root morphology, PI exhibited significantly higher fine-root length in diameters &lt;0.5 mm, a greater number of root tips, and longer root tips compared to LE. In addition, the levels of different plant hormones, including auxin (IAA), abscisic acid (ABA), jasmonic acid (JA), and salicylic acid (SA), known for their diverse adaptation strategies to biotic stress, were analysed. The response to quinclorac-resistant barnyardgrass stress was consistent in terms of the content of well-known stress-related hormones, namely SA and JA. The accumulation of SA and JA was observed in both rice cultivars under the stress of quinclorac-resistant barnyardgrass, with higher contents of these hormones in PI than that in LE. The most significant change was observed in IAA and ABA contents in rice, which decreased significantly from 7 days to 14 days under co-culture stress. Additionally, PI contained higher levels of IAA and ABA than LE in the presence of barnyardgrass stress. This research may aid in the development of strategies for reducing the environmental impact of herbicides through the prudent selection of non-chemical herbicide control tactics.

The flowering of Amorphophallus bulbifer plays an important role in its reproduction. The flowers and leaves of A. bulbifer cannot grow at the same time. However, the physiological and molecular mechanisms involved in flower bud and leaf bud formation are still unclear. In this study, the flower buds and leaf buds of A. bulbifer in the early stage of growth were used as research materials, transcriptome and metabolome analyses were carried out, and the soluble sugar and starch contents of A. bulbifer corms were determined. Transcriptome analysis revealed 5 542 differentially expressed genes (DEG) between flower buds and leaf buds, 3 107 of which were upregulated and 2 435 of which were downregulated. Enrichment analysis of the KEGG pathway showed that these differential genes were enriched mainly in the plant hormone signal transduction, DNA replication and fatty acid elongation pathways. Plant hormone signal transduction, DNA replication and fatty acid elongation pathways. A total of 5 296 significant differentially abundant metabolites were screened out by nontargeted metabolomics analysis. The differentially abundant metabolites were functionally classified in the HMDB, and 118 were successfully matched, including 17 that were highly expressed in flower buds. The differentially abundant metabolites in the flower buds were mainly enriched in pathways such as amino acid metabolism, isoquinoline alkaloid biosynthesis and pyrimidine metabolism. Targeted metabolomics analysis revealed that the contents of ABA, ZT and iPA in flower buds were significantly greater than those in leaf buds, while the opposite trend was observed for IAA. The analysis of soluble sugar and starch contents showed that the starch and soluble sugar contents in flower buds were significantly greater than those in leaf buds. The results of this study showed that flower bud development in A. bulbifer was regulated by amino acids, starch, ABA, ZT, iPA, IAA and other hormones. These findings could lead to valuable genetic resources for further study of A. bulbifer flowering and provide a deeper understanding of the molecular basis of A. bulbifer flowering.

In order to solve the problem of the poor oil displacement effect of high molecular weight alkali/surfactant/polymer (ASP) solution in low permeability reservoirs, Daqing Oilfield uses a partial quality tool to improve the oil displacement effect in low permeability reservoirs. Without changing the oil displacement capability of high molecular weight ASP solution in high permeability oil layers, the ASP solution is actively sheared in low permeability oil layers by using a partial quality tool to increase the injection capability of the solution and improve the overall oil recovery. In order to study the ability of the partial quality tool to improve the oil displacement effect, firstly, the matching degree of high molecular weight ASP solution to low permeability cores is studied, and the ability of quality control tools to change the molecular weight is studied. Then, experimental research on the pressure and oil displacement effect of high molecular weight ASP solution before and after the actions of the partial quality tool is carried out. The results show that ASP solutions with molecular weights of 1900 × 104 and 2500 × 104 have a poor oil displacement effect in low permeability reservoirs. After the action of the partial quality tool, the injection pressure is reduced by 5.22 MPa, and the oil recovery is increased by 7.79%. The injection pressure of the ASP solution after shearing by the partial quality tool is lower than that of the ASP solution with the same molecular weight and concentration without shearing, but the oil recovery is lower. On the whole, the use of the partial quality tool can obviously improve the oil displacement effect in low permeability reservoirs.

Four angucycline glycosides including three new compounds landomycin N (1), galtamycin C (2) and vineomycin D (3), and a known homologue saquayamycin B (4), along with two alkaloids 1-acetyl-β-carboline (5) and indole-3-acetic acid (6), were identified from the fermentation broth of an intertidal sediments derived Streptomyces sp. Their structures were mainly established by IR, HR-ESI-MS, 1D and 2D NMR techniques. Among the isolated angucyclines, saquayamycin B displayed potent cytotoxic activity against hepatoma carcinoma cells HepG-2, SMMC-7721 and plc-prf-5, with IC50 values 0.135, 0.033 and 0.244 μM respectively, superior to positive drug doxorubicin. Saquayamycin B treatment to SMMC-7721 cells led to the typical morphological signs of apoptosis in 4',6-diamidino-2-phenylindole (DAPI) staining experiment.

We investigated the response of leaf photosynthetic capacity to climate warming and its variation among provenances of Larix gmelinii (Dahurian larch). Seedlings of 11 L. gmelinii provenances were transplanted into two common gardens with different climate conditions (control and warming climate). We measured the leaf photosynthetic capacity and explored its influencing factors. The warming treatment significantly increased the maximum net photosynthetic rate (Pmax-a), photosynthetic nitrogen use efficiency (PNUE), maximum carboxylation rate (Vcmax), maximum electron transport rate (Jmax), triose phosphate utilization rate (TPU), mesophyll conductance (gm), leaf nitrogen content (Narea), and chlorophyll content (Chlm). The Pmax-a was significantly positively associated with Vcmax, Jmax, TPU, gm, and Narea, and the slope of the correlations between Pmax-a and Vcmax, Jmax, and TPU was steeper in the warming treatment. The responses of Pmax-a, PNUE, Vcmax, Jmax, TPU, Narea, and Chlm to warming differed among provenances. The effects of warming on Pmax-a, Vcmax, Jmax, and TPU increased and then decreased as the aridity index of the original site increased. Overall, the warming treatment improved the photosynthetic capacity of L. gmelinii, but the extent of the improvement varied among provenances. These findings provide insights into the mechanisms underlying the responses of L. gmelinii to climate warming.

The genus Amomum encompasses six medicinal species that are extensively utilized and have a significant historical background. Due to their morphological similarities, however, the presence of counterfeit and substandard products remains a challenge. Accurate plant identification is therefore essential to address these issues. This study utilized 11 newly sequenced samples along with extensive data from NCBI to perform molecular identification of these six species. The plastomes of Amomum displayed a typical quadripartite structure with conserved gene content, yet showed independent variations in the SC/IR boundary shifts at both inter- and intra-specific levels. Our approach incorporated ITS, ITS1, ITS2, complete plastomes, matK, rbcL, and psbA-trnH sequences for molecular identification, which effectively differentiated the six medicinal species within the genus Amomum, as confirmed by distance-based and phylogenetic tree analyses. Among these, the ITS, ITS1, and complete plastomes sequences demonstrated the highest identification success rate (3/6), followed by ITS2, matK, and psbA-trnH (1/6). In contrast, rbcL failed to identify any species. This research successfully established a reliable molecular identification method for Amomum plants, to protect wild plant resources and promote the sustainable use of medicinal plants and restrict the exploitation of these resources.

In March 2013, a novel avian influenza A H7N9 virus was emerged in China, which cause rapidly progressive pneumonia and with a high fatality rate. Serologic studies to evaluate neutralizing antibodies of infected patients and birds are invaluable tools for immunogenicity research of H7N9 and epidemiological investigation. Conventional neutralization assays are laborious and time-consuming which also hampered by biosafety requirement. In this study, We construct and produce pseudovirus bearing the full-length hemagglutinin (HA) of H7N9 virus in the Env-defective, luciferase-expressing HIV-1 backbone. The production of lentiviral pseudovirus was analysed by HA gene specific real-time reverse-transcription PCR, transmission electron microscopy (TEM), and Western Blot assay to prove the nucleic acid replication, the morphology of virus, and the expression of HA protein in pseudovirus. After that pseudovirus based inhibition assay was established to detect neutralizing antibodies of a panel of serum samples. Our results demonstrated that H7N9 pseudovirus which had single-cycle infection was generated. By comparing the neutralization antibody titers, pseudovirus based neutralization test could be recognized as an alternative of conventional microneutralization (MN). Hence, we conclude that it is possible to use pseudovirus inhibition assay to screen sera samples, as well as evaluate vaccine-induced neutralizing antibodies against H7N9 virus.

By reviewing the research of development economics in recent years, five key terms of ‘innovation, coordination, green, openness and sharing’ are extracted, corresponding to the five dimensions of the New Development Concept advocated by China. Based on this, an evaluation index system of the development quality of China's fishery industry is constructed. The spatio-temporal characteristics of China's fishery industry development quality were analyzed by using the provincial panel data from 2007 to 2017. The results show that: i) China's fishery industry overall development quality continues to grow, while the variation of provincial quality is also increasing, and the contribution of innovation quality and sharing quality is increasing, becoming an important sub-dimension leading the overall development quality.ii) there is a significant spatial dependence among provincial quality, and the significance is further strengthening. The Hangzhou Bay area and Bohai Bay area have gradually become a dual-core area where the high-quality development of China's fishery industry agglomeration, and the radiation from the dual-core area to the peripheral areas may still be in the process of enhancement. The spatial and temporal distribution of China’s fishery industry development quality keeps the trend of ‘from northeast to southwest’, which is almost parallel to Hu Huanyong line. The gravity center of its distribution is close to the gravity center of Chinese population and economy, and the development quality experienced a process from relatively concentrated to dispersed and then returned to concentrated, and the development speed in the later period was higher than that in the earlier period. iii) Capital accumulation level is the dominant positive influencing factors, while government support level is the dominant negative influencing factors respectively, and both have significant spatial differentiation among provinces.

Background: Educating college students about the importance of good sleep habits could lead to the adoption of healthier sleep routines, including sufficient sleep duration and sleep quality. The current pre-post study examines the impact of completing a sleep education program called “Sleep 101” on (1) sleep hygiene practices, (2) sleep quality, and (3) weekday and weekend sleep behaviors among college students. “Sleep 101” is an interactive online course developed to educate college students about the importance of sleep by addressing basic sleep physiology, the impact of sleep on mood, academic and physical performance, the interactions between sleep and various substances, and common sleep disorders. Methods: 338 college students were recruited from a midsized public university in the US and invited to participate in “Sleep 101”, of which 25 participants completed the baseline and post-intervention questionnaire. The Sleep Hygiene Index (SHI) was utilized to evaluate sleep hygiene practices, while standard questions were employed to assess weekday and weekend sleep behaviors and overall sleep quality. Results: Those who completed the study demonstrated a significant increase in weekday sleep duration and were less likely to engage in negative prior bedtime activities. In addition, 40% of those who completed baseline and post-intervention assessments noticed improvements in their sleep quality. Conclusion: These findings suggest that a brief online program is beneficial in improving sleep behaviors among college and could be a scalable approach to addressing current sleep issues and preventing future sleep problems in college students.

In order to correct attenuated millimeter-wavelength (Ka-band) radar data and address the problem of instability, an attenuation correction methodology (attenuation correction with variation trend constraint; VTC) was developed. Using synchronous observation conditions and multi-band radars, the VTC method adopts the variation trends of reflectivity in X-band radar data captured with wavelet transform as a constraint to adjust reflectivity factors of millimeter-wavelength radar. The correction was evaluated by comparing reflectivities obtained by millimeter-wavelength cloud radar and X-band weather radar. Experiments showed that attenuation was a major contributory factor in the different reflectivities of the two radars when relatively intense echoes exist, and the attenuation correction developed in this study significantly improved data quality for millimeter-wavelength radar. Reflectivity differences between the two radars were reduced and reflectivity correlations were enhanced. Errors caused by attenuation were eliminated, while variation details in the reflectivity factors were retained. The VTC method is superior to the bin-by-bin method in terms of correction amplitude and can be used for attenuation correction of shorter wavelength radar assisted by longer wavelength radar data.

During HVDC earth return operation systems, a high magnitude current will be injected into soil through earth electrode, the potential on the surface would change widely and produce unfavorable effects on the AC systems around. This paper presents an effective finite element method (FEM) coupling electric field with thermal field to evaluate the electrical field induced by the injected DC current. Firstly, owe to the characteristic of FEM, this method can consider arbitrary soil and earth electrode structure. Secondly, by setting the electrical and thermal parameters of soil as a function of temperature at the same time, the dynamic coupling process of electric field and thermal field is simulated accurately. Thirdly, to deal with the singular point in FEM subdivision and the huge computation in traditional three-dimensional FEM, the FEM coupling 2-D earth electrode with 3-D soil based on "shell" theory is introduced. Finally, based on the suggested method, the effect of abnormal resistance region (ARR) near DC earth electrode on electric field distribution is analyzed.

As the lifespan of porous asphalt pavement extends, it invariably experiences performance degradation and an increase in tire/pavement noise compared with the original surface when it is newly built. To understand the medium-term performance of porous asphalt pavement during service and reveal the influence of different pavement performance indicators on tire/pavement noise generation, a seven-year continuous observation and data analysis study was conducted. Porous asphalt with different designed material parameters was taken into account, including thin-layer porous asphalt overlay with a maximum nominal aggregate size of 10mm (PUC-10), porous asphalt with a maximum nominal aggregate size of 13mm (PAC-13), and a two-layer porous asphalt incorporating both PUC-10 and PAC-13 (PUC-10+PAC-13). Using automated pavement technology testing equipment, key performance indexes, including damage rate (DR), rut depth (RD), international roughness index (IRI), and sideway force coefficient (SFC), were measured and calculated. The on-board sound intensity (OBSI) method was used to test noise levels in three types of porous asphalt pavement structures and on a dense graded easy compact asphalt concrete (ECA) for comparison. The progressions of the medium-term performances were analyzed according to the measured results. The correlations between tire/pavement noise levels and testing speed, testing lane, pavement structure, and road condition indicators were investigated by regression. The research results revealed that the DR and SFC of the three types of porous asphalt pavement displayed more significant attenuation in the service period, while the IRI and RD showed small changes. Among them, the SFC demonstrated significant attenuation over the first 4 years, decreasing between 13.8% and 17.0%. From the 3-7 years of operation, the transverse crack disease in porous asphalt pavement progressed rapidly. The three porous asphalt pavement structures tested exhibited commendable noise reduction capabilities. Compared to ECA, the OBSI noise levels of these structures were lower by 2.09 dB, 1.53 dB, and 2.88 dB, respectively. Compared to other pavement condition indicators, RD had a more significant impact on the OBSI value of the PUC-10 porous asphalt pavement. For the PUC-10+PAC-13 porous asphalt pavement, there was a significant linear relationship between the OBSI value and SFC, mainly due to polishing of the coarse aggregate surface. It leads to a decrease of the micro-texture, which lies in increasing tire/pavement noise at high-frequency ranges and decreasing SFC. This study will have guiding significance for the research of the attenuated law and durability improvement of porous asphalt tire/pavement noise.

Leaf color mutants (LCMs) are important resources for studying diverse metabolic processes such as chloroplast biogenesis and differentiation, pigments’ biosynthesis and accumulation, and photosynthesis. However, in Dendrobium officinale, LCMs are yet to be fully studied and exploited due to the unavailability of reliable RGs (reference genes) for qRT-PCR (quantitative real-time reverse transcription PCR) normalization. Hence, this study took advantage of previously released transcriptome data to select and evaluate the suitability of ten candidate RGs, including Actin (Actin), polyubiquitin (UBQ), glyceraldehyde-3-phosphate dehydrogenase (GAPDH), elongation factor 1-α (EF1α), β-tubulin (β-TUB), α-tubulin (α-TUB), 60S ribosomal protein L13-1 (RPL13AD), aquaporin PIP1-2 (PIP1-2), Intima protein (ALB3) and Cyclin (CYCB1-2) for normalizing leaf color-related genes’ expression levels via qRT-PCR. Stability rankings analysis via common software Best-Keeper, GeNorm, and NormFinder disclosed that both ten genes met the requirements of RGs. Of them, EF1α exhibited the highest stability and was selected as the most reliable. The reliability and accuracy of EF1α were confirmed through qRT-PCR analysis of fifteen chlorophyll pathway-related genes. The expression patterns of these genes via EF1α normalization were consistent with the results by RNA-Seq. Our results will pave the way for molecular dissection of leaf color mutations in D. officinale.

Microfluidics is facing critical challenges in the quest of miniaturizing, integrating, and automating in vitro diagnostics, including the increasing complexity of assays, the gap between the macroscale world and the microscale devices, and the diverse throughput demands in various clinical settings. Here a “3D extensible” microfluidic design paradigm that consists of a set of basic structures and unit operations was developed for constructing any application-specific assay. Four basic structures- check valve (in), check valve (out), double-check valve (in and out), and on-off valve, were designed to mimic basic acts in biochemical assays. By combining these structures linearly, a series of unit operations can be readily formed. We then proposed a “3D extensible” architecture to fulfill the needs of the function integration, the adaptive “world-to-chip” interface, and the adjustable throughput in the X, Y, and Z directions, respectively. To verify this design paradigm, we developed a fully integrated loop-mediated isothermal amplification microsystem that can directly accept swab samples and detect Chlamydia trachomatis automatically with a sensitivity one order higher than that of the conventional kit. This demonstration validated the feasibility of using this paradigm to develop integrated and automated microsystems in a less risky and more consistent manner.

Polymeric composites such as Poly-ether-ether-ketone (PEEK)/carbon fiber (CF) have been widely utilized due to outstanding performances such as high specific strength and specific modulus. The PEEK/CF components via powder-bed fusion additive manufacturing usually show brittle fracture behaviors induced by their poor interfacial affinity and inner voids. These defects are strongly associated with powder packing quality upon deposition. The particle dynamic model has been widely employed to study the interactions of particle motions. Powder property, bulk material property, and interfacial features of composite powders are key factors in the particle dynamic model. In this work, an efficient and systematic material evaluation is developed for composite powders to investigate their deposition mechanism. The discrete element method is utilized to simulate the dynamic behaviors of PEEK/CF composite powders. The powder properties, bulk material properties, and interfacial features of powders are calibrated and justified by experimental measurement, numerical simulation, and design of experiments. The particle dynamic model can well explain the powder flow behaviors and interactions. It reveals that the addition of short CF particles can assist the flow of PEEK powders and improve the packing quality of the composite powders.

Codon use bias is an important characteristic in the process of genetic information transmission of species. With the publication of the genome of C. panzhihuaensis, it is of great significance to investigate the codon use bias for understanding the genetic evolution of this species and for molecular breeding. In this study, Perl language and CodonW 1.4.2 software was used to systematically analyze the coding gene sequences of the C. panzhihuaensis genome, obtain the characteristics of codon use, and identify the sources of variation affecting codon use. The results showed that GC3s content, GCall content, and ENC value were 46.75%, 47.67%, and 52.8 respectively. As the first seed plant, the GC3 content of Cycas is similar to that of most gymnosperms and most dicotyledons, but considerably different from that of monocotyledons.RSCU value was greater than 1, among which 21 codons ended in U or A. Enc-plot analysis, PR2-plot neutral plot analysis, and correlation coefficient analysis of Axis1 with GC3s and CAI revealed that the codon bias was mainly affected by natural selection, but also by mutation pressure and other factors. Thirty-one optimal codons of Cycas genes were screened. This research can provide a reference for the phylogeny and genome codon evolution of Cycas.

Infrared small target detection (ISTD) plays a crucial role in both civilian and military applications. The detection of small targets against dense cluttered backgrounds remains a challenging task, requiring the collaboration of false alarm source elimination and target detection. Existing approaches primarily focus on modeling targets while often neglecting false alarm sources. To address this limitation, we propose a Target and False Alarm Collaborative Detection Network to leverage the information provided by false alarm sources and the background. Firstly, we introduce a False Alarm Source Estimation Block (FEB) that estimates potential interferences present in the background by extracting features on multiple scales and employing stepwise upsampling for feature fusion. Subsequently, we propose a framework that employs multiple FEBs to eliminate false alarm sources across multiple scales. Finally, a Target Segmentation Block (TSB) is introduced to accurately segment the targets to produce the final detection result. Experiments on public datasets demonstrate that, compared to other methods, our model achieves high accuracy in segmenting targets while being able to extract false alarm sources which can be used for further studies.

As the most important city in China, Beijing has experienced an economic soar, large-scale population growth and eco-environment changes in recent 20 years.Evaluating climate and human-induced vegetation changes could reveal the relationship of vegetation-climate-human activities and provide important insights for the coordination of economic growth and environmental protection. Based on a long-term MODIS vegetation index dataset, meteorological data (temperature, precipitation) and impervious surface data, the Theil-Sen regression and the Mann-Kendall method are used to estimate vegetation change trend in this study and the residual analysis is utilized to distinguish the impacts of climate factors and human activities on vegetation restoration and degradation from 2000 to 2019 in Beijing. Our results show that the increasing vegetation areas account for 80.2\% of Beijing. The restoration of vegetation is concentrated in the urban core area and mountainous area, while the degradation of vegetation is mainly concentrated in the suburbs. In recent years, the vegetation in most mountainous areas has changed from restoration to significant restoration, indicating that the growth of mountain vegetation has continued to restore. We also found that in the process of urban expansion, vegetation browning occurred in 53.1\% of the urban built-up area, while vegetation greening occurred in the rest part. We concluded that precipitation is the main climatic factor affecting the growth of vegetation in Beijing mountain areas through correlation analysis. Human activities have significantly promoted the vegetation growing in the northern mountainous area thanks to the establishment of environmental protection areas. The negative correlation between vegetation and the impervious surface tends to gradually expand outwards, which is consistent with the trend of urban expansion. The positive correlation region remains stable, but the positive correlation is gradually enhanced. The response of vegetation to urbanization demonstrated a high degree of spatial heterogeneity. These findings indicated that human activities played an increasingly important role in influencing vegetation changes in Beijing.

Solar assisted hybrid cooling systems are promising for the energy saving of refrigeration systems. In most cases, the solar thermal gain is only able to power the heat-driven process of facilities in part of the working period. Therefore, the reduction of compressor power strongly depends upon the duration of heat-driven processes, which has not been addressed properly. Motivated by such knowledge gap, the thermodynamic understanding of solar assisted hybrid cooling systems is deepened through considering the duration in heat-driven processes. Three absorption-compression integrated cooling cycles were taken as examples. It is found that optimal parameters, e.g., inter-stage pressure and temperature, corresponding to various performance indicators trend to be identical, as the duration of heat-driven processes is taken into account. Furthermore, the optimal parameter for different working conditions was obtained. It is displayed that the dimensionless optimal intermediate temperature of layout with the cascade condensation process varies slightly, e.g., 4%, for different conditions. Moreover, the fall of compressor power in entire working periods is nearly independent upon the intermediate temperature. The paper is favorable for the efficient design and operation of solar assisted hybrid cooling systems.

Recently, the outbreak of coronavirus disease 2019 (COVID-19) is threatening human health globally. There is a dire need to find potential therapeutic agents. Angiotensin converting enzyme 2 (ACE2), as an entry receptor of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2), is considered as potential therapeutic target in COVID-19 pandemic. Here, our bioinformatics analysis revealed that the biological function of ACE2 was correlated with regulation of blood pressure and mediation of SARS-CoV-2 entry into host cells. Ten ACE2 cooperative proteins were identified by using STRING with a high score. ACE2 expressed highly in the small intestine, testis, and kidney. The level of ACE2 expression in tumor tissues varies in different types of cancers compared with that in normal tissues. It was worth noting that the expression level of ACE2 in the tumor has no effect on patient survival. MiRNA hsa-miR-942-5p, and three transcription factors (TFs) including Signal transducer and activator of transcription 4 (STAT4), Estrogen related receptor α (ESRRA), and Signal transducer and activator of transcription 3 (STAT3) were selected as novel ACE2 regulators. Moreover, nine potential therapeutic drugs were predicted by two online databases. Thus, our research may expand the overall view of ACE2 in COVID-19 treatment.

In the study, a new correction method was applied to reduce error during detection on mixed pesticide residue in apples by using Raman spectra. Combined with self-built pesticide residues detection system by Raman spectroscopy and the application of surface enhancement technology, rapid real-time qualitative and quantitative analysis of deltamethrin and acetamiprid residues in apples can be applied effectively. In quantitative analysis, compared with the intensity value of characteristic peaks of single pesticide with same concentration, the intensity value of characteristic peaks of the two pesticides decreased after mixing the pesticides, which interferes the results severely. By comparing the difference in the intensity of characteristic peaks of single and mixed pesticides, a correction method is proposed to eliminate the influence of pesticides mixture. Characteristic peak intensity values of gradient concentration pesticide from 10-1 g•kg-1 to 10-6 g•kg-1 and Lagrangian interpolation are applied in the correction method. And a smooth surface is applied to describe the correction ratio of characteristic peak intensity. Through detecting the characteristic peak intensity values of the mixed pesticide, correction ratio will be obtained. Then real values of the peak intensity of pesticides and the content of each component of the mixed pesticide will be acquired by the correction method. Correlation coefficient of model validation exceeds 0.88 generally and Root Mean Square Error also decreases obviously after correction, which proved the reliability of the method.

In bioinformatics research, traditional machine learning methods have demonstrated efficacy in addressing Euclidean data. However, real-world data often encompasses non-Euclidean forms, such as graph data, which contain intricate structural patterns or high-order relationships that elude conventional machine-learning approaches. Representation learning seeks to derive valuable data representations from enhancing predictive or analytic tasks, capturing vital patterns and structures. This method has proven particularly beneficial in bioinformatics and biomedicine, as it effectively handles high-dimensional, sparse data, detects complex biological patterns, and optimizes predictive performance. In recent years, graph representation learning has become a popular research direction. It embeds graphs into a low-dimensional space while preserving the structural and attribute information of the graph, enabling better feature extraction for downstream tasks. This study extensively reviews representation learning advancements, particularly in the research of representation methods since the emergence of COVID-19. We begin with an analysis and classification of neural network-based language model representation learning techniques as well as graph representation learning methods. Subsequently, we explore their methodological innovations in the context of COVID-19, with a focus on the domains of drugs, public health, and healthcare. Furthermore, we discuss the challenges and opportunities associated with graph representation learning. This comprehensive review presents invaluable insights for researchers as it documents the development of COVID-19 and offers experiential lessons to preempt future infectious diseases. Moreover, this study guides future bioinformatics and biomedicine research methodologies.

Co-free Li-rich oxide is a promising cathode for low cost high energy density Li-ion battery but presents poor cyclic stability. To address this issue, CeO2 is coated on Co-free Li-rich oxide through a low-temperature aged process, resulting in a novel CeO2-coated Li-rich oxide compo-site. Due to the low-temperature aged process, a uniform CeO2 coating layer of 6 nm in thickness is successfully coated on Co-free Li-rich oxide. With this uniform coating, the resulting CeO2-coated Li-rich oxide composite presents improved cyclic stability as well as rate capability as the cathode of Li-ion battery. The capacity retention of the resulting CeO2-coated Li-rich oxide is enhanced from 67% to 85% after 100 cycles and its capacity retention of 5C/0.05C is enhanced from 10% to 23%, compared with the uncoated sample. Such significant improvements enable this low-temperature aged process to be helpful for the practical application of Li-rich oxide materials, not limited to Co-free Li-rich oxide.

The uncertainty in the secondary path of an Active Noise Control (ANC) headphone affects the waterbed effect and stability of the feedback system. This study focuses on the uncertainty of the secondary path when real users wear headphones, and proposes a new uncertainty constraint based on the measured results of the secondary path transfer function under different wearing conditions of dummy head and limited subjects. This constraint and a cascaded second-order infinite impulse response filter with fixed coefficients are used to formulate a control strategic function, which is optimized by the Improved Grey Wolf Optimizer (IGWO) algorithm to obtain the optimal controller with better noise reduction performance. The proposed method and simulation model are validated based on the experimental test results. The results demonstrate that the safety factor and waterbed suppressing factor contained in the proposed uncertainty constraint ensures more stable noise reduction and effective suppression of the waterbed effect for new subjects without a priori data.

The limitations of conventional sensors have made phased array antennas increasingly crucial for gathering information and communication applications in intelligent transportation systems. Compact cylindrical arrays, in particular, are favored for their ability to achieve azimuth angle scan. However, the substantial mutual coupling effect between elements on curved surfaces and its implication in these arrays remains unclear, which is a crucial factor to consider when such arrays are used for multibeam applications. This study investigated the effect of mutual coupling in a dual-slant-polarized cylindrical array. The results showed that mutual coupling is essential for achieving an ultra-wide bandwidth. Mutual coupling is predominantly observed among elements that are closely positioned. The study also analyzes the impact of mutual coupling on scan impedance and radiation characteristics for multibeam applications and reveals that these arrays exhibit robust multibeam capability, hence having great potential for use in intelligent transportation systems.

Trailing oil is the tail section of contamination. There are two main reasons for the formation of trailing oil, one is the effect of laminar flow boundary layer, the other is the outflow of the preceding batch remained in the dead-legs. In the batch transportation of refined oil, under the action of viscous force, the preceding batch forms laminar boundary layer near the pipe wall and stays on the pipe wall, resulting in the phenomenon of contamination trailing and formation of trailing oil. When oil passes through the valve chamber of the oil transportation station, dead-leg will be formed. Due to gravity and convection diffusion, preceding batch flowing from dead-legs will form trailing oil in the pipeline. The phenomenon of trailing oil exists in the process of batch transportation, which will have an effect on the quality of oil. In this paper, Reynolds time-averaged method is used to simulate turbulence.Computational Fluid Dynamics(CFD) software is used to simulate different flow rates and bypass lengths to obtain contamination-related experimental data.Matlab software is used to perform multi-nonlinear regression for the oil substitution time, the length of the bypass and the flow rate. The formula for calculating the length of the trailing oil produced by the dead-leg is obtained. The modified formula for calculating the length of the contamination is obtained by combining the existing formula for calculating the length of the contamination.

SLEUTH Model (slope, landuse, exclusion, urban extent, transportation and hillshade) is an important tool for landuse planning and land policy. To evaluate the performance of SLEUTH model, implementation of Sensitivity Analysis (SA) is essential. The main limitation of SA in SLEUTH application is a lack of insight into model input self-modification parameters (SMPs) variation, namely, uncertainty involved in the model transfer metrics and model presumptions, which often misled the decision makers and model users. To address this issue, this study divided the forward process into two stages. Firstly, during the transfer process ①, the contribution scores of five SMPs were drawn, and parameters highly sensitive to model output were given. Apart from that, the recommended initial value for SMPs of 0.11, 0.2, 0.87, 1.13, 15, 1.01, 0.49 were found to be subordinated to such a heterogeneous urban area simulation. Secondly, during the transfer process ②, SMP caused imagery metrics indicated the disparity between parameters with Fixed Reference and with Successive Reference. Reversely, it derives reasonable threshold for the best fit values of five prediction coefficients’ initialization by comparing the real image with the predicted one. The framework of SLEUTH model transfer mechanism not only could distinguish highly sensitive SMPs with higher contribution scores, but also could give parametric analysis for simulation imagery based on metrics. The study was found to be a practical tool for quantization response of model input variables for modelling complex urban systems. So, this insight can help geographic information scientists decide how to find out the inner forward transfer mechanism of SLEUTH model for further make good use of it and improve the model.

Melon pest management relies on the excessive application of pesticides. Reducing pesticide spraying has become a global issue for environmental sustainability and human health. Therefore, developing a new cropping system that is sustainable and eco-friendly is important. This study found that melon seedlings irrigated with ultrafine water containing H2 and O2 (UFW) produced more root hairs, increased shoot height, and produced more flowers than the control irrigated with reverse osmosis (RO) water. Surprisingly, we also discovered that UFW irrigation significantly reduced aphid infestation in melon. Based on cryo-scanning electron microscope (cryo-SEM) observations, UFW treatment enhanced trichome development and prevented aphid infestation. To investigate whether it was H2 or O2 that helped to deter insect infestation, we prepared UF water enrichment of H2 (UF+H2) and O2 (UF+O2) separately and irrigated melons. Cryo-SEM results indicated that both UF+H2 and UF+O2 can increase the density of trichomes in melon leaves and petioles. RT-qPCR showed that UF+H2 significantly increased the gene expression level of the trichome-related gene GLABRA2 (GL2). We planted melons in a plastic greenhouse and irrigated them with ultrafine water enrichment of hydrogen (UF+H2) and oxygen (UF+O2). The SPAD value, photosynthetic parameters, root weight, fruit weight, and fruit sweetness were all better than the control without ultrafine water irrigation. UFW significantly increased trichome development, enhanced insect resistance, and improved fruit traits. This system thus provides useful water management for pest control and sustainable agricultural production.

Study Objectives: To (1) investigate the prevalence of sleep disorder symptoms in caregivers of children with autism spectrum disorder (ASD) and (2) the relationships between caregiver sleep problems and their health-related quality of life and family quality of life. Methods: Descriptive cross-sectional study of caregivers (N=62) of children ages 6 to 11 years old diagnosed with ASD receiving care at a regional autism research and resource center. Measurements and Results: Participants completed the Sleep Habits Questionnaire (SHQ), the Medical Outcomes Study (MOS) SF-12, and the Beach Center Family Quality of Life Scale (FQOL). Caregivers with longer sleep duration reported better mental health and better family quality of life. Caregivers who reported insomnia symptoms, non-restorative sleep, and insufficient sleep were more likely to report poorer mental health than caregivers who did not report these sleep disorder symptoms. Caregivers with obstructive sleep apnea and restless legs syndrome experienced worse physical quality of life. Conclusions: The physical and mental health of the primary caregiver is essential to the support of the child with ASD and to the functioning of the family. The study findings point to the importance of future research and interventions to enhance sleep health in order to improve quality of life for caregivers of children with ASD.

Temporal downscaling of gridded geophysical data is essential for improving climate models, weather forecasting, and environmental assessments. However, existing methods often could not accurately capture multi-scale temporal features, affecting their accuracy and reliability. To address this issue, we introduce an Enhanced Residual U-Net architecture for temporal downscaling. The architecture, which incorporates residual blocks, allows for deeper network structures without the risk of overfitting or vanishing gradients, thus capturing more complex temporal dependencies. The U-Net design inherently could capture multi-scale features, making it ideal for simulating various temporal dynamics. Moreover, we implement a flow regularization technique with advection loss to ensure that the model adheres to physical laws governing geophysical fields. Our experimental results across various variables within the ERA5 dataset demonstrate an improvement in downscaling accuracy, outperforming other methods.

Ethylene is an ideal CO2 product in an electrocatalytic CO2 reduction reaction (CO2RR), which has high economic value. In this paper, Al–doped octahedral Cu2O (Al–Cu2O) catalyst was synthesized by a simple wet chemical method. The selectivity of CO2RR products was improved by doping Al onto the surface of octahedral Cu2O by regulating the Al content. The Al–Cu2O was used as an efficient electrocatalyst for CO2RR with selective ethylene production. The Al–Cu2O exhibited a high Faradic efficiency (FEC2H4) of 44.9% at -1.23 V (vs. RHE) in CO2 saturated 0.1 M KHCO3 electrolyte. Charge transferring from Al atom to Cu atom take place after Al doping in Cu2O, thereby optimizing the electronic structure, which facilitates CO2RR to ethylene production. The DFT calculation showed that the Al–Cu2O catalyst can effectively reduce the adsorption energy of the *CHCOH intermediate and promote the mass transfer of charges, thus improving the FEC2H4. After Al doping into Cu2O, the center of d orbitals shift positively, which makes the d–band closer to the Fermi level. Furthermore, the density of electronic states increases, which was conducted to the interaction between Cu atoms and intermediates, thus accelerating the electrochemical CO2 reduction process. This work proved that the metal doping strategy can effectively improve the catalytic properties of Cu2O, thus providing a useful way for CO2 cycling and green production of C2H4.

As a member of smart materials, electrorheological elastomers (EREs) formed by pre-treating active electrorheological particles are attracting more and more attention. In this work, four Mg-doped strontium titanate particles with spherical, dendritic, flake-like and pinecone-like morphorlogies were obtained by hydrothermal and low-temperature co-precipitation. XRD, SEM, Raman and FT-IR were used to characterize the obtained products. The results showed that the sizes of Mg-doped strontium titanates are about 1.5‒2.0 μm, and the phase structure are dominated by cubic crystal. These Mg-doped strontium titanates were dispersed in a hydrogel composite elastic medium. Then, Mg-doped strontium titanate/glycerol/gelatin electrorheological composite hydrophilic elastomers were obtained with or without electric field. The electric field response properties of Mg-doped strontium titanate composite elastomers were investigated. It concluded that dendritic Mg-doped strontium titanate composite elastomers is high-performance EREs. And the maximum value of energy storage modulus of Mg-doped strontium titanate composite elastomers has achieved 8.70 MPa. This high electrorheological performance of the products is helpful for their applications in vibration control, force transducers, smart structures, dampers, and other fields.

Building energy consumption is the main urban energy consumption component, which mainly serves people-centered work and living energy demands. Based on the physical requirements of humans in urban buildings and to determine the comfortable body temperature in each season, this paper establishes a sizing optimization model of building-type integrated energy systems (IES), where the cooling and heating loads required to maintain indoor somatosensory body comfortable temperature are calculated. Depending on the external energy price, internal power balance and other constraints, the model develops an optimal sizing and capacity panning method of energy conversion and storage unit in a building-type IES with PV generation. The operating principle is described as follows: the PV generation is fully consumed, a gas engine satisfies the electric and thermal base load requirements, while the power system and a heat pump supply the remaining loads. The gas price, peak-valley electricity price gap and heat-topower ratio of gas engines are considered as important factors for the overall techno-economic analysis. The developed method is applied to optimize the economic performance of building-type IES and verified by practical examples. The results show that using the complementary characteristics of different energy conversion units is important to the overall IES cost.

In order to study the crystallinity of different density polyethylenes, the experimental study on the transformation of the conductance mechanism under high electric field was carried out. The X-ray Diffraction(XRD), Different Scanning Calorimeter(DSC), Direct Current(DC) breakdown of Low-density polyethylene(LDPE), Linear low density polyethylene(LLDPE), Medium density polyethylene(MDPE) and High-density polyethylene(HDPE) and the electric field of 5-200kV/mm were tested. Conductivity characteristics experiments, in addition, using the mathematical formula of a variety of conductance mechanisms, the electric field-current density curves of the four kinds of polyethylene were fitted to analyze the conductance transition of the above four kinds of polyethylene in non-ohmic regions under different high field strengths. mechanism. The experimental results show that as the density of polyethylene increases, the crystallinity increases continuously, and the continuous increase of crystallinity causes the electric conduction flow under the same field strength to decrease significantly. The field strength corresponding to the two turning points in the conductance characteristic curve increases simultaneously. Large, the breakdown field strength increases; through analysis, it is found that in the high field, as the electric field increases, the conductance mechanism develops from the ohmic conductance of the low field strength region to the bulk effect of the high field strength region (Poole-Frenkel). Then the electrode effect to the high field strength (Schottky), and the threshold field strength of this conductance mechanism transition increases with the increase of crystallinity.

In-situ grown C_0.3N_0.7Ti and SiC, which derived from non-oxide additives Ti₃SiC₂, are proposed to densify silicon nitride (Si₃N₄) ceramics with enhanced mechanical performance. Remarkable increase of density from 79.20% to 95.48% could be achieved for Si₃N₄ ceramics with 5vol% Ti₃SiC₂. The capillarity of decomposed Si from Ti₃SiC₂, and in-situ reaction between nonstoichiometric TiC_x and Si₃N₄ were believed to be responsible for densification of Si₃N₄ ceramics. An obvious enhancement of flexural strength and fracture toughness for Ti₃SiC₂ doped Si₃N₄ ceramics was observed. The maximum flexural strength of 795 MPa for Si₃N₄ composites with 5vol% Ti₃SiC₂ and maximum fracture toughness of 6.97 MPa^.m^1/2 for Si₃N₄ composites with 20vol% Ti₃SiC₂ are achieved when mixed powders are hot-press sintered at 1700℃. Pull out of elongated Si₃N₄ grains, crack bridging, crack branching and crack deflection were demonstrated to dominate enhance fracture toughness of Si₃N₄ composites.

JIS SUJ2 is most widely used in bearing steels. The advantages are good hardenability, excellent fatigue, wear resistance and comprehensive mechanical properties. For wear resistance and fatigue resistance of the steel are getting more and more attention, the residual stress state and its distribution on the surface of the heat affect zone are critical factors affecting the fatigue life and wear resistance of the parts. In this study, using the SUJ2 as the material to talk about the surface residual stress and retained austenite distribution. Doing the quenching and tempering treatment to obtain different microstructures, using the induction method to re-quench the case region. After the heat treatment, measuring the residual stress and retained austenite volume on the surface by X-ray diffraction, observing the microstructure and comparing the hardness. The results show that the microstructure after heat treatment contains unsolidified carbides, tempered martensite and retained austenite. The residual stress on the surface is the tensile state. In the re-hardened area after induction quenching, the residual stress is all compressive, and the values are more than -800 MPa. In conclusion, in the same output power condition can be observed that the microstructure of the specimens before induction hardening has a significant impact on the effective case depth. The surface residual stress has changed from a tensile to a compressive state. In the re-hardened area, the maximum of the residual compressive stress increased with the austenitized temperature increase.

MCrAlX (M: Ni or Co or both, X: minor elements) coatings have been widely used to protect hot components in gas turbines against oxidation and hot corrosion at high temperatures. Understanding the influence of the X-elements on oxidation behaviour is important in the design of durable MCrAlX coatings. In this study, NiCoCrAlX coatings doped with Y+Ru and Ce, respectively, were deposited on Inconel-792 substrate by HVOF. The samples were subjected to isothermal oxidation test in laboratory air at 9000, 1000, 1100 ºC and cyclic oxidation test between 100 ºC and 1100 ºC with 1 hour dwell time at 1100 ºC. It was observed that the coating with Ce shows a much higher oxidation rate than the coating with Y+Ru under both isothermal and cyclic oxidation tests. Besides, β-depletion due to interdiffusion between coating and substrate was significantly lower with Ru addition. Simulations results using both a moving phase boundary model and an established oxidation-diffusion model show that Ru stabilize β grains which reduces β-depletion of coating due to substrate interdiffusion. This paper presents a comprehensive study of the influence of Ce and Ru on oxidation behaviour including investigation of the microstructure evolution influenced by oxidation time at coating surface and coating-substrate interface combining experiment and simulation results.

In the present study, an attempt was made to induce rooting from single-node cuttings of hybrid aspen (Populus tremula L. ×P. tremuloides Michx.) with different concentrations of IAA, IBA and NAA during rooting. Among the three auxins used, NAA showed more effective induction on rooting as compared to IAA and IBA at the whole level. Thereafter, NAA was used further in experiments for anatomical and biochemical investigation. The results showed that it took 12 days from the differentiation of primordium to the appearance of young adventitious roots with NAA application. It was found that endogenous IAA, ZR and GA3 levels increased, but ABA decreased in cuttings with 0.54 mM NAA treatment. In contrast to the endogenous IAA level, NAA had negative effect on IAA-oxidase (IAAO) activity. Similarly, the decreased peroxidase (POD) activity, consistent with down-regulation of expressed levels of POD1 and POD2, was observed in NAA-treated cuttings. Whereas, NAA resulted in a higher activity in polyphenol oxidase (PPO) compared to the control cuttings. Collectively, the study highlighted that 0.54 mM NAA is efficient on rooting in hybrid aspen, and its effect on metabolic changes during rooting is discussed, which provide valuable information for propagating hybrid aspen.

Buckling defect will appear on the outer surface of the deformed ring during constrained ring rolling (CRR) of aluminum alloy thin wall conical ring with inner high ribs (AATWCRIHR), if the geometrical dimension of the ribs doesn't match the wall thickness. To avoid the buckling defect, a quantitative method for characterizing the degree of the buckling defect is proposed using the area of buckling profile. Then an orthogonal experimental scheme was designed taking the width of the middle rib, thickness of wall, and height of the middle rib as design variables and defining the area of buckling profile as optimization objective. Subsequently, a quadratic polynomial response surface model was established by combining the optimization algorithm with the finite element method (FEM), and the geometrical dimension of the middle ribs of the deformed AATWCRIHR is optimized. Also the optimal parameter combination to minimize the area of buckling profile is obtained and verified using FE simulation. Results show that the AATWCRIHR after optimization doesn’t generate the buckling defect during constrained ring rolling, and it is proved that the quantitative buckling defect representation method and the optimization design method based on the response surface model and the finite element simulation results are feasible for the constrained ring rolling process of the AATWCRIHR.

The Loess Plateau is an important region for vegetation restoration in China, however, changes in soil organic carbon (SOC), soil nutrients, and stoichiometry after restoration in this vulnerable ecoregion are not well understood. Typical restoration types, including orchardland (OL), grassland (GL), shrubland (SL), and forestland (FL) were chosen to examine changes in the stocks and stoichiometry of SOC, soil total nitrogen (TN), and soil total phosphorus (TP) at different soil depths and recovery times. Results showed that SOC stocks first increased and then stabilized in OL, GL, and SL at 0–30 cm depth, while in FL, stocks gradually increased. Soil TN stocks first increased and then decreased in OL, SL, and FL with vegetation age at 0–30 cm depth, while soil TP stocks showed little variation between restoration types. In the later stages of restoration, the stocks of SOC and soil TN at 0–30 cm soil depth were still lower than those in natural grassland (NG) and natural forest (NF). The overall C:N, C:P, and N:P ratios increased with vegetation age. Additionally, the SOC, soil TN and soil TP stocks, and C:N, C:P, and N:P ratios decreased with soil depth. The FL had the highest rate of change in SOC and soil TN stocks, at 0-10 cm soil depth. These results indicate a complex response of SOC, soil TN, and soil TP stocks and stoichiometry to vegetation restoration, which could have important implications for understanding C, N, and P changes and nutrient limitations after vegetation restoration.

The effects of exogenous inorganic [i.e., nitrate (NO3-)/ammonium (NH4+)] and organic [i.e., glutamate (Glu)/argine (Arg)] N alone and in combination on the accumulation of proline (Pro) in rice plant under trivalent chromium [Cr(III)] stress were studied through the mass balance matrix model (MBMM). ‘NH4+’ application showed the largest contribution to the Pro content in rice shoots under different concentrations of Cr(III), followed by ‘NO3-’, ‘Arg’, and ‘Glu’ application respectively. While, ‘Arg’ application displayed the largest contribution to the Pro content in roots under Cr(III) stress, followed by ‘NH4+’, ‘Glu’, and ‘NO3-’ application. Among the combination cases of N sources used, the application of ‘NH4++Arg’ showed the greatest contribution to the Pro content in both roots and shoots of Cr(III)-treated rice seedlings, while the application of ‘NO3-+Glu’ showed the least contribution to the Pro content in rice seedlings under Cr(III) stress. Results from this study indicated that the level of indigenous Pro in rice seedlings is quite sensitive to Cr(III) stress under different N sources, and mathematical modeling showed a reliable result to estimate the relationship between Pro content and N source application in rice plants in response to Cr(III) exposure .

The physical and mechanical properties of rocks will change significantly after being subjected to high temperatures, which poses safety hazards to underground projects such as coal underground gasification. In order to investigate the effect of temperature on the macroscopic and microscopic properties of rocks, this paper has taken sandstone as the research object and conducted uniaxial compression tests on sandstone specimens at different temperatures (20-1000 ℃) and different heating rates (5-30 ℃/min) at 1200 ℃. At the same time, the acoustic emission (AE) test system was used to observe the acoustic emission characteristics of the rock damage process, and the microstructural changes after high temperature were analyzed with the help of a scanning electron microscope (SEM). The test results show that the effect of temperature on sandstone is mainly divided into three stages: Ⅰ (20-500 ℃) stage is the strengthening zone, the evaporation of water and the contraction of primary fissures, sandstone densification is enhanced. Specifically, the compressive strength and elastic modulus increase, the macroscopic damage mode is dominated by shear damage, and the fracture micro-morphology is mainly brittle fracture. Stage II (500-600°C) is the transition zone, 500°C is the threshold temperature for compressive strength and modulus of elasticity, and the damage mode changes from shear to cleavage damage, and the sandstone undergoes brittle-ductile transition in this temperature interval. Stage III is the physicochemical deterioration stage. The changes in physical and chemical properties make the sandstone compressive strength and modulus of elasticity continue to decline, the macroscopic damage mode is mainly dominated by cleavage damage, and the fracture microscopic morphology is more toughness fracture. The effect of different heating rates on the mechanical properties of sandstone was further studied, and it was found that the mechanical properties of the rock were more deteriorated under higher heating rates.

To understand the molecular mechanism underlying yellowing in pineapples during ripening, coupled with alterations in fruit quality, comprehensive metabolome and transcriptome investigations were carried out. These investigations were conducted using the pulp samples collected at three distinct stages of maturity: young fruit (YF), mature fruit (MF), and fully mature fruit (FMF). This study revealed a noteworthy increase in the levels of total phenols and flavones, coupled with a concurrent decline in lignin and total acid content, as the fruit transitioned from YF to FMF. Furthermore, the analysis yielded 167 differentially accumulated metabolites (DAMs) and 2194 differentially expressed genes (DEGs). Kyoto Encyclopedia of Genes and Genomes enrichment analysis based on DAMs and DEGs revealed that the biosynthesis of plant secondary metabolites, particularly the flavonol, flavonoid, and phenypropanoid pathways, plays a pivotal role in fruit yellowing. Additionally, a comprehensive regulatory network encompassing genes that contribute to metabolisms of flavones, flavonols, lignin, and organic acids was proposed. This network sheds light on the intricate processes that underlies fruit yellowing and quality alterations. These findings enhance our understanding of the regulatory pathways governing pineapple ripening and offer valuable scientific insight into the molecular breeding of pineapples.

Intercropping systems can flexibly use resources such as sunlight, heat, water, and nutrients in time and space, improve crop yield and land utilization rates, effectively reduce continuous cropping obstacles and the occurrence of diseases and insect pests, and control the growth of weeds. Thus, intercropping is a safe and efficient ecological planting mode. The legume–cereal intercropping system is the most common planting combination. Legume crops fix nitrogen from the atmosphere through their symbiotic nitrogen fixation abilities, and the fixed nitrogen can be transferred to and utilized by cereal crops in various ways. The symbiotic nitrogen fixation efficiency of legume crops was improved by reducing the inhibition of soil nitrogen on nitrogenase activity through competitive absorption of soil nitrogen. However, the effects of nitrogen transformation and distribution in intercropping systems, and microbial community structure characteristics on nitrogen transfer need to be further explored. In this review, ⅰ) we present the transformation and distribution of nitrogen in the legume–cereal intercropping system; ⅱ) we describe the soil microbial community characteristics in intercropping systems; and ⅲ) we discuss the advantages of using modern biological molecular techniques to study soil microorganisms. We conclude that intercropping can increase the diversity of soil microorganisms, and the interaction between different plants has an important impact on the diversity and composition of the bacterial and fungal communities. The extensive application of modern biological molecular techniques in soil microbial research and the great contribution of intercropping systems to sustainable agriculture are particularly emphasized in this review.

Introduction The Pericapsular Nerve Group (PENG) block is a novel technique that allows for analgesia of the anterior hip capsule via the articular branches of the accessory obturator nerve and femoral nerve, which have a significant role in the innervation of the hip capsule. PENG blockade is effective in both adult and pediatric patients. However, there are no studies in the available literature on patients under five years of age. Herein, we describe our experience with two pediatric patients with hip dysplasia. Purpose This study aimed to evaluate the analgesic effect of the pericapsular nerves group (PENG) in small children undergoing hip surgery. Patients and methods This study included two patients, aged 2 and 4 years old, who qualified for hip surgery. General or spinal anesthesia with the addition of a PENG block was performed. During the procedure, the basic hemodynamic parameters were monitored. After the surgery, the patients received 15mg/kg-1 iv paracetamol every 6 hours to prevent rebound pain. The pain was assessed using the FALCC score. The 15mg/kg-1 metamizole was administered if the FLACC score was 3. In the FLACC score 4, the application of 0,2mg/kg-1 Nalpain was ordered. Results The patient's hemodynamic parameters were stable and within normal range. FLACC scores from all patients ranged from 0 and 3 in the first 24 h period. One patient required metamizole 12 hours after surgery. No evidence of block complications was observed. Conclusions This case series showed that PENG block provided adequate postoperative analgesia and assured opioid-free pain management. However, we are convinced that future randomized, controlled trials are needed in this field.

Variety of harmful gases are produced in asphalt mixture after mixing, paving and rolling process. Effective measures must be tak-en to suppress the asphalt pavement in the tunnel due to fire accidents and other toxic gases and fumes, reducing the human health during the construction process. In this study, a flame retardant and smoke suppressant (compound) with Mg(OH)2 as the main component was developed, the flame retardant asphalt mixture and asphalt mastics were prepared to evaluate the flame retard-ant-smoke suppressant properties and performance effects. Firstly, its low and high temperature performances were investigated with the bending beam rheometer (BBR) and dynamic shear rheological (DSR), respectively. Then, the indoor combustion test and the cone calorimeter test were used to evaluate the fire retardant smoke suppression effect of the asphalt mastic. Thirdly, the flame retardant effect of asphalt mastic mixed with the compound was further analyzed by thermogravimetric (TG) test and scanning electron microscopy (SEM). The pyrolysis temperature, mass loss and microscopic state of asphalt surface were used to verify and explain the flame retardant reaction effect and process of the compound. Finally, the asphalt mixture performance was evaluated, as well as the flame retardant smoke suppression effect was verified by asphalt mixture combustion tests. The results showed that the flame retardant smoke suppression time of the flame retardant asphalt mixture was reduced by 66% and the smoke emission area was reduced by 20%. The flame retardant smoke suppression effect of the asphalt mixture was improved by 44%. The flame-retardant and smoke-suppressing compound and the asphalt mixture with the compound prepared in this study meet the asphalt mixture performance and flame retardant smoke suppression function, providing an option for application of fire retardant and smoke-suppressing asphalt pavement materials in tunnels.

To accurately and non-destructively monitor the growth of spring wheat in the Hetao Irrigation Area, UAV remote sensing was employed during various fertility stages. Digital image indices from diverse fertilization treatments were calculated and compared with physiological indices to identify the most sensitive digital image indices corresponding to these indices. The study underscored the critical importance of the flowering stage in the growth of spring wheat, thus highlighting the necessity of focusing on this stage. This finding reiterated that the flowering stage was pivotal for spring wheat development in the Hetao Irrigation Area. Several digital image indices, such as GLA, R, G, INT, g, GRVI, MGRVI, RGBVI, EXG, and GRRI, exhibited a high frequency of significant correlations with physiological indices during the four primary reproductive stages of wheat. Consequently, these sensitive digital image indices during the flowering stage can more effectively characterize the physiological indices of spring wheat.

To conduct a precise impact assessment of marine diesel engines, a 200t floating impact platform was utilized to simulate realistic testing conditions. The testing generated the acceleration time curve and the impact response spectrum for the diesel engine. According to the applicable standards, the spectral velocity was chosen as the evaluation index, and an evaluation of the longitudinal, transverse, and vertical impact environment of the diesel engine was conducted. The shock factor interpolation method was corrected using the confidence interval based on normal distribution, and the interpolated confidence interval of the shock factor was determined. The findings reveal that: The 200t-class floating shock platform is capable of providing a reliable shock environment for diesel engine tests. The shock wave serves as the primary external force during the experiment, and the impact of bubble pulsation can be disregarded when assessing using the floating shock platform. To more accurately describe the experimental shock intensity when presented with dispersed data, the confidence interval can be utilized, and the resulting prediction formula provides a higher level of impact safety. The obtained conclusions can serve as a reference for predicting the shock environment of large shipboard equipment using the shock platform.

In this study, the effects of various beryllium (Be) addition (Be-free, 0.1, 0.25, 0.50 wt.%) on the microstructure, mechanical properties, and corrosion corrosion of the Al-Mg-Li alloys were systematically investigated. The best performance was obtained in alloy with 0.1 wt.% Be addition. Trace Be addition promotes the grain refinement of the as-cast alloy ingot and contributes positive effects to the recrystallization, bringing improvement of tensile property. Meanwhile, the best anti-corrosion behavior is also presented at 0.1 wt.% Be addition, due to its potential to reduce the width of precipitates free zone (PFZ). As the Be content increase to an excessive level, the comprehensive performance decreases. Therefore, it is strongly recommended that adding trace Be element into Al-Mg-Li alloys has a positive effect on the comprehensive service performance.

Accurate lithium battery diagnosis and prognosis is critical to increase penetration of electric vehicles and grid-tied storage systems. They are both complex due to the intricate, nonlinear, and path-dependent nature of battery degradation. Data-driven models are anticipated to play a significant role in the behavioral prediction of dynamical systems such as batteries. However, they are often limited by the amount of training data available. In this work, we generated the first big data comprehensive synthetic datasets to train diagnosis and prognosis algorithms. The proof-of-concept datasets are over three orders of magnitude larger than what is currently available in the literature. With benchmark datasets, results from different studies could be easily equated, and the performance of different algorithms can be compared, enhanced, and analyzed extensively. This will expend critical capabilities of current AI algorithms, tools, and techniques to predict scientific data.

Li₂MnO₃ is critical component in the well-studied Li-excess cathode materials xLi₂MnO₃•(1- x)LiMO₂ for achieving high lithium storage capacity. In this article, the diffusion of Li ions in Li₂MnO₃ is studied using molecular dynamics (MD) simulation with well-behaved empirical force fields obtained by fitting against the crystal structure from experiment and phonons calculated using Density Function Theory (DFT). We have found two possible tetrahedral hopping channels, 0-TM and 1-TM(Mn⁴⁺) channel, which are differentiated by the face sharing octahedral cations. Simulation results show that the 0-TM channel is active for Li hopping, while 1-TM(Mn4+) channel is inactive. During the delithiation process, the Li ions in the TM layered are firstly removed, then those in the Li layer. However, the Li ions will be trapped in the tetrahedral 0-TM channels as long as the four face sharing octahedral sites are cleared. Up to x=1.0 for Li₂-xMnO₃, almost all the Li ions are located at the tetrahedral sites, forming a regular array along a axis. The de-intercalation of tetrahedral Li ions requires a high voltage (>5.2 V vs. Li/Li+), limiting the practical capacities measured in lab. The diffusion of Mn ions into the Li layers is observed in a deeper delithiated structure (x=1.2 for Li₂-xMnO₃), indicating an initial phase transformation to a spinel-like structure. However, the Mn ions are mainly trapped in the tetrahedral sites in the Li layer, instead of the octahedral sites fin spinel-like structure. A few of Mn ions diffusing into the octahedral sites in Li layers have no face sharing tetrahedral Li ions, revealing a further Li de-intercalation is imperative for the complete phase transformation. Our model is not stable for x≥1.4 in Li₂-xMnO₃. Other charge compensation mechanism should be considered in this high delithiation stage, eg. oxygen release.

Over the past couple of decades, Global positioning system (GPS) technology has been utilized to collect large-scale data from travel surveys. As the precise spatiotemporal characteristics of travel could be provided by GPS devices, the issues of traditional travel survey, such as misreporting and non-response, could be addressed. Considering the defects of dedicated GPS devices (e.g., need much money to buy devices, forget to take devices to collect data, limit the simple size because of the number of devices, etc.), and the phenomenon that the smartphone is becoming one of necessities of life, there is a great chance for the smartphone to replace dedicated GPS devices. Although, several general reviews have been done about smartphone-based GPS travel survey in the literature review section in some articles, a systematic review from smartphone-based GPS data collection to travel mode detection has none. The included studies were searched from six databases. The purpose of this review is to critically assess the current literature on the existing methodologies of travel mode detection based on GPS raw data collected by smartphones. Meanwhile, according to the systematic comparison among different methods from data-preprocessing to travel mode detection, this paper could carefully provide the Strengths and Weaknesses of existing methods. Furthermore, it is the crucial step to develop the methodologies and applications of GPS raw data collected by smartphones.

We investigate and discuss in detail the structure of the restricted singular value decomposition for a tensor triplet under t-product (T-RSVD). The algorithm is provided with a numerical example illustrating the main result. For applications, we consider color image watermarking processing with T-RSVD.

The layer-by-layer (LBL) fabrication method allows for controlled microstructure morphology and vertical component distribution, and also offers a reproducible and efficient technique for fabricating large-scale organic solar cells (OSCs). In this study, polymer D18 and PYIT-OD are employed to fabricate all-polymer solar cells (all-PSCs) using the LBL method. Morphological studies reveal that the use of additives optimizes the microstructure of the active layer, enhancing the crystallinity and charge transport capability. The optimized device with 2% CN additive significantly reduces bimolecular recombination and trap-assisted recombination. All-PSCs fabricated by the LBL method based on D18/PYIT-OD deliver a power conversion efficiency (PCE) of 15.07%. Our study demonstrates the great potential of additive engineering via LBL fabrication method in regulating microstructure of active layers, suppressing charge recombination, and enhancing the photovoltaic performance of devices.

In this paper, a swarm trajectory planning method is proposed for multiple autonomous surface vehicles (ASVs) in an unknown and obstacle-rich environment. Specifically, based on the point cloud information of the surrounding environment obtained from local sensors, a kinodynamic path searching method is used to generate a series of waypoints in the discretized control space at first. Next, after fitting B-spline curves to the obtained waypoints, a nonlinear optimization problem is formulated to optimize the B-spline curves based on gradient-based local planning. Finally, a numerical optimization method is used to solve the optimization problems in real-time to obtain collision-free, smooth and dynamically feasible trajectories relying on a shared network. Simulation results demonstrate the effectiveness and efficiency of the proposed swarm trajectory planning method for a network of ASVs.

Here, a process for leaching vanadium from calcified roasting pellets (CPVC) of vanadium-titanium iron concentrate by a two-stage sulfuric acid cycle was proposed. When the silicon removal acid concentration of the pellet in the first stage was 1.5 mol/L, the solid-liquid ratio was 6: 1, the silicon removal acid concentration of the leaching solution was 3.0 mol/L, and the standing time was 48 h, the silica gel formation time was 23 h, the filtration time was 70 s, and the loss rates of vanadium and iron were 1.52% and 0.17%, respectively. When the acid concentration was 2 mol/L, at room temperature, using a leaching time of 28 days, and a solid-liquid ratio of 5: 1 in the second stage, the total leaching rates of vanadium and iron were 75.52% and 0.71%, respectively. The concentration of vanadium in the leaching solution reached 6.80 g/L, and vanadium was directly precipitated without extraction. After secondary roasting, the crushing strength of the pellets reached 2250 N, which met the requirement for blast furnace iron making. The Eh-pH diagrams of the V-Fe-H2O system at different temperatures were plotted. Thermodynamically, it was difficult to selectively leach vanadium and iron by changing the conventional acid leaching conditions. In addition, the pellets before and after leaching were analyzed. The grade of iron in the pellets increased slightly after leaching, and the main phases in the pellets remained as Fe2O3 and Fe9TiO15. The S in the sulfuric acid solution entered the leached pellets during the acid leaching reaction and was removed by the secondary roasting of the leached pellets.

Ultrasound based haptic feedback is a potential technology for human-computer interaction (HCI) with the advantages of low cost, low power consumption and controlled force. In this paper, the phase optimization for multipoint haptic feedback based on ultrasound array is investigated and the corresponding experimental verification is provided. A mathematical model of acoustic pressure is established for the ultrasound array and then a phase optimization model for an ultrasound transducer is constructed. We propose a pseudo-inverse (PINV) algorithm to accurately determine the phase contribution of each transducer in the ultrasound array. By controlling the phase difference of the ultrasound array, the multipoint focusing forces are formed leading to various shapes such as geometries and letters that can be visualized. Because the unconstrained PINV solution results in unequal amplitudes for each transducer, a weighted amplitude iterative optimization is deployed to further optimize the phase solution, by which the uniform amplitude distributions of each transducer are obtained. For the purpose of experimental verifications, a platform of ultrasound haptic feedback consisting of a Field Programmable Gate Array (FPGA), an electrical circuit and an ultrasound transducer array is prototyped. The haptic performances of single point, multiple points and dynamic trajectory were verified by controlling the ultrasound force exerted on the liquid surface. The experimental results demonstrate that the proposed phase optimization model and theoretical results are effective and feasible, and the acoustic pressure distribution is consistent with the simulation results.

Directional modulation (DM), as an emerging promising physical layer security (PLS) technique at the transmitter side with the help of an antenna array, has developed rapidly over decades. In this study, a DM technique using a polarization sensitive array (PSA) to produce the modulation with different polarization states (PSs) at different directions is investigated. A PSA, as a vector sensor, can be employed for more effective DM for an additional degree of freedom (DOF) provided in the polarization domain. The polarization information can be exploited to transmit different data streams simultaneously at the same directions, same frequency, but with different PSs in the desired directions to increase the channel capacity, and with random PSs off the desired directions to enhance PLS. The proposed method has the capability of concurrently projecting independent signals into different specified spatial directions while simultaneously distorting signal constellation in all other directions. The symbol error rate (SER), secrecy rate, and the robustness of the proposed DM scheme are analyzed. Design examples for single- and multi-beam DM systems are also presented. Simulations corroborate that 1) the proposed method is more effective for PLS; 2) the proposed DM scheme is more power-efficient than the traditional artificial noise aided DM schemes; and 3) the channel capacity is significantly improved compared with conventional scalar antenna arrays.

A phenomenological constitutive model is developed to describe the uniaxial transformation ratcheting behaviors of super–elastic shape memory alloy (SMA) by employing a cosine–type phase transformation equation with the initial martensite evolution coefficient that can capture the feature of the predictive residual martensite accumulation evolution and the nonlinear hysteresis loop on a finite element (FE) analysis framework. The effect of the applied loading level on transformation ratcheting are considered in the proposed model. The evolutions of transformation ratcheting and transformation stresses are constructed as the function of the accumulated residual martensite volume fraction. The FE implementation of the proposed model is carried out for the numerical analysis of transformation ratcheting of the SMA bar element. The integration algorithm and the expression of consistent tangent modulus are deduced in a new form for the forward and reverse transformation. The numerical results are compared with those of existing model and the experimental results to show the validity of the proposed model and its FE implementation in transformation ratcheting. Finally, a FE modeling is established for a repeated preload analysis of SMA bolted joint

Industrial process control systems commonly exhibit features of time-varying, strong coupling, and strong nonlinearity. Obtaining accurate mathematical models of these nonlinear systems and achieving satisfactory control performance is still a challenging task. In this paper, data-driven modeling techniques and deep learning methods are used to accurately capture a category of smooth nonlinear system’s spatiotemporal features. The operating point of these systems may change over time, and their nonlinear characteristics can be locally linearized. We established the LSTM-CNN-ARX model by utilizing a fusion of long short-term memory (LSTM) network and convolutional neural network (CNN) to fit the coefficients of the state-dependent exogenous variable autoregressive (SD-ARX) model. Compared to other models, the hybrid LSTM-CNN-ARX model is more effective in capturing the nonlinear system’s spatiotemporal characteristics due to its incorporating the strengths of LSTM for learning temporal characteristics and CNN for capturing spatial characteristics. The model-based predictive control (MPC) strategy, namely LSTM-CNN-ARX-MPC, is developed by utilizing the model's local linear and global nonlinear features. The control comparison experiments conducted on a water tank system (WTS) show the effectiveness of the developed models and MPC methods.

This paper concentrates on the general birth-death processes with two different types of catastrophes. The Laplace transform of transition probability function for birth-death processes with two-type catastrophes are is successfully expressed with the Laplace transform of transition probability function of the birth-death processes without catastrophe. The first effective catastrophe occurrence time is considered. The Laplace transform of its probability density function, expectation and variance are obtained.

The time’s arrow of macroscopic physical phenomenon is reflected by irreversible physical process, which essentially occurs from small probability state to high probability state. In this paper, simplified models are proposed to understand the macroscopic physical process. In order to describe the information of a physical system, we defined the full self-information as "information height" to describe the complexity or difficulty of a macrostate of physical system. In this way, the direction of macroscopic physical process is from high information height to low information height. We can judge the direction of physical process by the information height. If we want the macroscopic physical process to evolve from the low information height state to the high information height state, the system need to add extra information and corresponding energy to increase the information height.

The B169L protein (pB169L) of African swine fever virus (ASFV) is a structural protein with an unidentified function during the virus replication. The sequences of the B169L gene and the downstream B438L gene are separated by short intergenic regions. However, the regulatory mode of the gene transcription remains unknown. Here, we identified two distinct promoter regions and two transcription start sites (TSS) located upstream of the open reading frame (ORF) of B438L. Using the promoter reporter system, we demonstrated that the cis activity of the ORF proximal promoter exhibited significantly higher levels compared with that of the distal promoter located in the B169L gene. Furthermore, transfection with the plasmids with two different promoters for B438L could initiate the transcription and expression of the B438L gene in HEK293T cells, and the cis activity of the ORF proximal promoter also displayed the higher activities compared with the distal promoter. Interestingly, the B438L distal promoter also initiated the transcription of the alternatively spliced B169L mRNA (B169L mRNA2) encoding a truncated pB169L (tpB169L) (amino acids 92–169), and the gene transcription efficiency was increased upon mutation of the initiation codon located upstream of the alternatively spliced B169L gene. Taken together, we demonstrated that the distal promoter of B438L gene initiates the transcription of both the B438L mRNA and B169L mRNA2. Comprehensive analysis of the transcriptional regulatory mode of the B438L gene is beneficial for the understanding of the association of B438L protein and pB169L and the construction of the gene-deleted ASFV.