Emergency control load-shedding is a key solution to prevent blackouts in the power system. This paper proposed a new model of emergency controls load shedding based on the fast identification of the unstable state of the power system. K-means clustering algorithm divided the instability mode into the clusters. The results of analysis of this cluster were used as the basis for classification control. Building load shedding strategies is consisted of the pre-designed rules based on AHP algorithm. When the recognition of the power system “instability” is detected, the signal of load shedding control is triggered immediately, therefore the decision time is greatly shortened comparing to the traditional methods. The effectiveness of the proposed method was tested on the IEEE 39-bus to overcome the limitations of the last traditional methods.

Objective: This study aimed to demonstrate the availability of portable devices for nasal FeNO measurement, which could replace exhaled NO measurement based on the continuous aspiration of multiple flow measurement systems. Methods: A descriptive cross-sectional study. The healthy subjects without rhinosinusis disorders (control group) and those with diagnosed allergic rhinitis (AR group) were enrolled in the study. They underwent nasal and bronchial FeNO measurements by both fixed flow NObreath® connected to nasal mask and multiple flows HypAir FeNO®. Results: A total of 153 people were recruited including 63 healthy subjects and 90 subjects with AR. There were no statistically significant differences in anthropometric characteristics between the two groups (P > 0.05). There were a significant increase in FeNO values in the AR group compared to the control group; concentrations of nasal and bronchial FeNO mearsured by NObreath® were 76.0 ± 50.7 ppb (vs 36.0 ± 28.1 ppb, P < 0.01) and 32.3 ± 15.4 ppb (vs 9.2 ± 5.6 ppb, P < 0.001), and those mearsured by NObreath® Hypair FeNO® were 1796.9 ± 523.3 ppb (vs 400.2 ± 123.1 ppb, P < 0.001) and 37.3 ± 23.0 ppb (vs 17.4 ± 18.3 ppb, P < 0.01). A weak correlation between the values measured by NObreath® and Hypair FeNO® devices was observed (r = 0.023 and r = 0.089, respectively; p < 0.05). Conclusions: The handheld NObreath® device is effective in measuring FeNO concentrations in both normal subjects and AR patients. The advantages in price and size, creating a compact, low-cost device that is convenient for use and research.

Logistics industry has been found to be among the key sources of carbon emission. In Vietnam logistics industry, there is a considerable difference between the number of foreign and Vietnamese firms as well as the proportion of markets that they are taking. This study is to research the low-carbon emission measures conducted by domestic and foreign invested logistics service providers (LSPs) and compare the results of the two groups. Both qualitative and quantitative approaches are applied. Literatures in relevant fields are reviewed and expert opinions are taken for structuring a questionnaire which was later distributed to 279 LSPs, with 166 returned and 159 being valid for data calculation. The results imply that there are differences in extension of applications of low-carbon practices between foreign and domestic firms. Except for transport mode switch and energy-saving lighting, the other practices witness that adoption levels of foreign LSPs are higher than their counterparts, which is possibly thanks to their global operation, more comfortable capital resources and awareness level of green initiative necessity. In conclusion, a comparison between the application conducted by foreign-invested firms and domestic ones, which has not been investigated before, was made.

Designing motion representations for the problem of 3D human action recognition from skeleton sequences is an important yet challenging task. An effective representation should be robust to noise, invariant to viewpoint changes and result in a good performance with low-computational demand. Two main challenges in this task include how to efficiently represent spatio-temporal patterns of skeletal movements and how to learn their discriminative features for classification task. This paper presents a novel skeleton-based representation and a deep learning framework for 3D action recognition using RGB-D sensors. We propose to build an action map called SPMF (Skeleton Posture-Motion Feature), which is a compact image representation built from skeleton poses and their motions. An Adaptive Histogram Equalization (AHE) algorithm is then applied on the SPMF to enhance their local patterns and form an enhanced action map, namely Enhanced-SPMF. For learning and classification tasks, we exploit Deep Convolutional Neural Networks based on the DenseNet architecture to learn directly an end-to-end mapping between input skeleton sequences and their action labels via the Enhanced-SPMFs. The proposed method is evaluated on four challenging benchmark datasets, including both individual actions, interactions, multiview and large-scale datasets. The experimental results demonstrate that the proposed method outperforms previous state-of-the-art approaches on all benchmark tasks, whilst requiring low computational time for training and inference.

Shales are well known for their strong anisotrophic properties. The classical Athy’s model on the exponential porosity reduction with the depth commonly uses based on localities only. Shale compaction curve affects the results of the basin modeling as it is important input data, thus the standard compaction curve of shales needs to be established. This study provided a new data and complies available data of Thailand shales to propose the new empirical relationship among porosity, burial depth, and geological age. The numerical data of the geological time were estimated by the application from the relationship of velocity and depth in each geological ages. The variation of the Thailand shale data due to the different geological ages was found in this study. Finally, the standard curve of shale compaction proposed by Puttiwongrak et al. [9] was examined and confirmed by this research findings.

Introduction: Hemostatic dysfunction during extracorporeal membrane oxygenation (ECMO) due to blood-circuit interaction and the consequences of shear stress by flow rates lead to rapid activation of the coagulation cascade and thrombus formation in the ECMO system and blood vessels. In this study, we aimed to identify the incidence and risk factors for cannula-associated arterial thrombosis (CaAT) post-decannulation. Methods: A retrospective study of patients undergoing arterial cannula removal following ECMO. We evaluated the incidence of CaAT and compared clinical characteristics, pre-ECMO severity, and daily hemostasis parameters in patients with and without CaAT. Multivariate analysis revealed the risk factors for CaAT. Results: Forty-seven patients requiring venoarterial ECMO or hybrid methods were recruited to be screened for thrombosis. The median SOFA score was 11 (8-13). CaAT occurred in 29 patients (61.7%), with thrombosis in the superficial femoral artery accounting for 51.7%. Limb ischemia complications in the group with CaAT was 17.2%. In multivariate analysis, an ECMO flow rate of 100 mL/min was determined to be the independent factor for CaAT with an OR of 0.84 (95% CI, 0.73–0.95, p=0.008). Conclusion: In patients successfully weaned from ECMO, the incidence of CaAT was 61.7%. Our study found that a low-flow rate of ECMO was an independent risk factor for CaAT.

Allanite minerals are the principal host of REEs in the Sin Quyen, Iron Oxide Copper Gold (IOCG) type deposit. The studied allanites have concentrations of: REE (14-27 wt%), Ca (9-16 wt%), Al (8-19 wt%), Si (26-34 wt%) and Fe (12-21 wt%). Two populations of allanite are documented, the first is texturally older probably related to the Ca-K alteration (second stage of crystallization). This population has higher REE concentrations ranging from 20 to 27 wt%, and the second population texturally younger has lower total REE concentration ranging from 14 to 19.9 wt%, which occur as a rim surrounding the older and likely arose during the K alteration with Cu-Au mineralization (third crystallization). Differences between the two allanite populations are documented by both optical properties and analysis of their chemical composition. The last parameter indicate that the studied allanites belong to the Ce-La-ferriallanite family, with low HREE with an average of 0.21 wt.%. Temperature 355ºC which was calculated using value of δ34S isotopes is interpreted as a temperature of the second crystallization stage of allanite. The pressure of crystallization solution was calculated and is ranging from 0.98 to 5.88 MPa.

IntroductionThe aim of this study is to describe the epidemiology of all COVID-19 patients in Vietnam and to describe the measures of disease control and prevention implemented. MethodsData were recovered from Wikipedia regarding the 2020 coronavirus pandemic in Vietnam. The period covered was from 23 January to 20 April 2020. Descriptive analysis was stratified by gender, age, country of origin, travel history, clinical symptoms and outcome. A survey of disease control and prevention measures was conducted at the Centre for Disease Control in the Thai Binh province, which is responsible for screening and isolating individuals at high risk of COVID-19. ResultsAs of 20 April 2020, Vietnam had recorded 268 confirmed COVID-19 patients. 55.2% were female. 67.9% were aged 20-49 years and 82.5% were Vietnamese. 60.4% of cases were imported from outside Vietnam. Other cases were acquired in Vietnam by individuals in close contact with imported cases. Only one patient who had not travelled had had no known contact with a confirmed case. 63.1% of patients were asymptomatic. 75.7% of patients were discharged. No deaths were recorded. The Thai Binh CDC surveyed a total of 2,203 persons at risk of COVID-19. 336 persons (15.2%) were isolated at hospitals and 1,411 (64.0%) in dedicated isolation facilities. 16.4% reported at least one respiratory symptom. No positive cases confirmed by RT-PCR have been reported in the Thai Binh province to date. ConclusionThe effect of the systematic screening and isolation strategy made it possible to limit local transmission in Vietnam. Vietnam needs to reinforce diagnostic capacities, prevention measures and provide the necessary epidemiological data on which to base interventions. The wider use of rapid serological tests is also advisable in order to be able to conduct extensive screening in the community.

The science‐policy interface in climate change adaptation became better managed over the past decades. However, the scientists and other knowledge producers, as well as policy makers still need to take bolder steps to more effectively engage with others to apply science and shape up policies. This paper aims to provide practical recommendations, intended to promote conversations between science and policy sectors to address climate change issues. Here, I used two different approaches to synthesize experiences and identify recommendations: a literature review and a case study. The paper stress main findings: (1) The linear communication model is still commonly involved in the science - policy dialogue and proved to be useful to increase the relevance of science and data products to decision makers. (2) When a gap between knowledge producer and knowledge user or decision maker exists, the need for a third party to specialize in bridging the gap become essential. (3) Indigenous people and knowledge must be involved in adaptation policy making based on legitimation local and traditional knowledge, designing the consultation process to broadly engage local and indigenous people, facilitating meaningful dialogues between traditional knowledge and science, and developing initiatives to strengthen skills and capacity of indigenous communities.

2-Methylquinazolin-4(3H)-one was prepared by reaction of anthranilic acid, acetic anhydride and ammonium acetate. The reaction of 2-methylquinazolin-4(3H)-one with N-aryl-2-chloroacetamides in acetone in the presence of potassium carbonate gave nine N-aryl-2-(2-methyl-4-oxoquinazolin-3(4H)-yl)acetamide compounds. The structures of these compounds were elucidated on the basis of their IR, 1H-NMR, 13C-NMR and HR-MS spectral data. These synthesized compounds containing the 2-methyl-3,4-dihydroquinazolin-4-one moiety exhibited excellent activity against Aedes aegypti mosquito larvae with LC50 values in the range of 2.085-4.201 μg/mL after 72 h exposure. Interestingly, these compounds did not exhibit toxicity to the non-target organism Diplonychus rusticus. In silico molecular docking revealed acetylcholine binding protein (AChBP) and acetylcholinesterase (AChE) to be potential molecular targets. These data indicated the larvicidal potential and environmental friendliness of these N-aryl-2-(2-methyl-4-oxoquinazolin-3(4H)-yl)acetamide derivatives.

News on the stock market contains positive or negative sentiments depending on whether the information provided is favorable or unfavorable to the stock market. This study aims to discover the news sentiment and classify news according to its sentiments with the application of PhoBERT, a Natural Language Processing model designed for the Vietnamese language. A collection of nearly 40,000 articles on financial and economic websites is used to train the model. After training, the model succeeds in assigning news to different classes of sentiments with an accuracy level of over 81%. The research also aims to investigate how investors concern about the daily news by testing the movements of the market before and after the news is released. The analysis results show that there is an insignificant difference in the stock price as a response to the news. However, investors tend to overreact to negative and positive news in the Vietnam stock market.

VNREDSat-1 is the first Vietnamese satellite allowing the survey of environmental parameters such as vegetation and water coverages, or surface water quality at medium spatial resolution (from 2.5 to 10 meters depending on the considered channel). The NAOMI sensor on board VNREDSat-1 has the required spectral bands to assess the suspended particulate matter concentration, SPM. Because recent studies have shown that the remote sensing reflectance, Rrs(), at the blue (450 – 520 nm), green (530 – 600 nm), and red (620 – 690 nm) spectral bands can be assessed from NAOMI with a good accuracy, the present study is dedicated to the development and validation of an algorithm (hereafter referred to as V1SPM) to assess SPM from Rrs() over inland and coastal waters of Vietnam. For that purpose, an in situ data set of hyper-spectral Rrs() and SPM (from 0.47 to 240.14 g.m-3) measurements collected at 205 coastal and inland stations has been gathered. Among the different approaches, including 4 historical algorithms, the polynomial algorithms involving the red-to-green reflectance ratio presents the best performance on the validation data set (MAPD of 18,7%). Compared to the use of a single spectral band, the band ratio allows to reduce the scatter around the polynomial fit as well as the impact of imperfect atmospheric corrections. Due to the lack of matchup data points with VNREDSat-1, the full VNREDSat-1 processing chain (RED-NIR and V1SPM) aiming at estimate SPM from the top-of-atmosphere signal has been applied to the Landsat-8/OLI match-up data points with relatively low to moderate SPM concentration (3.33-15.25 g.m-3) showing a MAPD of 15,8%. An illustration of the use of this VNREDSat-1 processing chain during a flooding event occurring in Vietnam is provided.

Motivation: there is a paradox at the heart of informatics where practical implementation generally fails to understand the socio-technical impact of novel technologies and disruptive innovation when adopted in `real-world’ systems. This phenomenon, termed technological determinism, is manifested in a time-lag between the adoption of novel technologies and an understanding of the underlying theory which develops following research into their adoption. Methods: we consider informatics theory as it relates to: social informatics and how humans’ function in society, the relationship between society and technology, information systems, information systems design, and human-computer interactions. The challenges posed by novel technologies and disruptive innovation are considered as they relate to information systems and information systems design. Open research questions with directions for future research are discussed with an introduction to and our proposed approach to socio-technical information system design. Significance: we conclude that the adoption of disruptive innovation presents both opportunities and threats for all stakeholders in computerised systems. However, determinism is a topic requiring research to generate a suitable level of understanding and technological determinism remains a significant challenge.

Extracts of Cordyceps militaris which possess the bioactive capacity such as antimicrobial activity and DPPH-free radical scavenging capacity, are applied to the serum product. This finished serum product has been evaluated the in vitro bioactivity and the stability with expect to find out a good extract with a suitable percentage used for serum product as natural materials on preservatives and antioxidation.

Floods are a common natural disaster whose severity in terms of duration, water resource volume, peak and accumulated rainfall-based damage are likely to differ significantly for different geographical regions. In this paper, we first propose a novel hourly flood index (SWRI24−hr−S), derived from normalising the existing 24-hourly water resources index (WRI24−hr−S) in literature, to monitor flash flood risks on an hourly scale. The proposed SWRI24−hr−S is adopted to identify a flood situation and derive its characteristics, such as the duration (D), volume (V) and peak (Q). The comprehensive result analysis establishes the practical utility of SWRI24−hr−S in identifying flood situations at seven study sites in Fiji between 2014 and 2018 and deriving their characteristics (i.e., D, V, and Q). Secondly, this study develops a vine copula-probabilistic risk analysis system that models the joint distribution of flood characteristics (i.e., D, V, and Q) to extract their joint exceedance probability for the seven study sites in Fiji, enabling probabilistic flood risk assessment. The vine copula approach, particularly suited to Fiji’s study sites, introduces a novel probabilistic framework for flood risk assessment. The results show moderate differences in the spatial patterns of joint exceedance probability of flood characteristics in different combination scenarios generated by the proposed vine copula approach. In the worst-case scenario, the probability of any flood event occurring where the flood volume, peak and duration are likely to exceed the 95th-quantile value (representing an extreme flood event) is found to be less than 5% for all study sites. The proposed hourly flood index and the vine copula approach can be feasible and cost-effective tools for flood risk monitoring and assessment. The methodologies proposed in this study can be applied to other data-scarce regions where only rainfall data is available, offering crucial information for flood risk monitoring, assessment, and the development of effective mitigation strategies.

Gas bubbles present in liquids underpin many natural phenomena and human-developed technologies that improve the quality of life. Since all living organisms are predominantly made of water, they may also contain gas bubbles—introduced both naturally and artificially—that can serve as biomechanical sensors operating in hard-to-reach places inside a living body and emitting signals that can be detected by common equipment used in ultrasound and photoacoustic imaging procedures. This kind of biosensors is the focus of the present article, where we critically review the emergent sensing technologies based on acoustically driven oscillations of gas bubbles in liquids and bodily fluids. This review is intended for a broad biosensing community and transdisciplinary researchers translating novel ideas from theory to experiment and then to practice. To this end, all discussions in this review are written in a language that is accessible to non-experts in specific fields of acoustics, fluid dynamics and acousto-optics.

The recent market and pandemic, with their complex nature and unpredictable developments, have had a great impact on coffee chains. The recovery factor in today's fiercely competitive coffee market is also derived from customer satisfaction, and the product's perceived value and ever with businesses' capabilities and recovery strategies. The research is based on the Customer and Service Recovery Performance model. Therefore, this study aims to investigate the impact of the Customer Satisfaction premise on the service recovery of the coffee chain and some other effects. After collecting surveys from 300 customers who have used beverages at famous coffee chains in Vietnam and performing data analysis via SEM-PLS, the results show that customer satisfaction positively influences customer loyalty. Customer loyalty mediates between customer satisfaction, and price fairness affects the resilience of the coffee chain. In addition, the two factors, Flexibility, and Adoption, also positively affect service recovery performance. Therefore, for coffee chains, customers are an important factor, and they need to maintain customer loyalty. In addition, seek ways to increase flexibility and apply technology at stores so that the company has enough experience and capacity to respond promptly to difficult market conditions, natural disasters and epidemics. This study presents insights into how coffee chains can adapt to the dynamic business environment during the current difficult business environment.

The principal minimum horizontal stress plays an important role in the study of reservoir characteristics, modeling of oil and gas reservoir, drilling, production and stimulating wells. However, it is currently not possible to measure the minimum horizontal stress along the wellbore as a geophysical parameter logging. Minimum horizontal stress is measured by leak-off test (LOT) at only several points in a well. In order to have the values all along the wellbore, experimental formulas were established to determine the minimum horizontal stresses for different fields. Then these formulas must be calibrated with LOT data whose number is usually limited, even sometimes unavailable. On the other hand, the empirical formulas of one field might not be accurate for another. This study presents a new approach to solve the problem of minimum horizontal stress estimation by a combination of artificial intelligence and geostatistics. The method consists of using artificial neural network (ANN) to build a model of minimum horizontal stress estimation from relevant parameters such as true vertical depth, pore pressure and vertical stress, then combined with Kriging interpolation to obtain the distribution in space of the minimum horizontal stress. Hence, this method can estimate the minimum horizontal stress with a limited amount of available data and therefore we do not need to drill new wells or to find empirical formulas for each survey area. The method was then applied in a case study involved real geomechanical dataset of Hai Thach - Moc Tinh field in Nam Con Son basin, Vietnam.

In recent years, there have been many new global companies investing and operating in Vietnam as a form of sharing economy (Uber, Grab, Foody, Agoda, Facebook, Google, etc). These kinds of economic models are popular in the world but very new in Vietnam. Sharing economy enterprises bring both benefit and challenges for Vietnam. Before time, there is no policy and law to govern the activities of these companies. So they make the challenges for the authority of Vietnam to manage. This paper will analyze the nature, characters, and impacts of the sharing economy in Vietnam. It also mentions the problems and recommends some solutions to manage the activities of sharing - economy companies.

E-learning with many outstanding advantages in training has drastically changed the self-study process due to the ability to personalize and effectively meet the learning activities of learners. E-learning and building an e-learning environment are currently paying attention and being deployed in many universities in Vietnam with different scope and levels. Especially in the current period, when science and technology are developing, many applications of technology and technology products have been applied in the field of education, changing the way of teaching and learning activities, the practice of both lecturers and students. Big Data and Artificial Intelligence (AI) technologies have replaced people not only for manual labor but also for intellectual labor, including the teaching of teachers. Many software applications have been used to replace people in the transmission of knowledge, testing, and evaluation of training quality, especially E-learning online training programs. However, in Vietnam today, the output quality of these online training programs has not been highly appreciated compared to similar programs in the world. The cause of this situation is that the training, teaching, and learning are not effective. Therefore, in this article, I will give some analysis, evaluate the current teaching and learning methods and propose solutions to enhance the interaction and initiative in the teaching and learning process of lecturers and students to improve the quality of online training in the future.

Non-standard Lagrangians do not display any discernible energy-like terms, yet they give the same equations of motion as standard Lagrangians, which have easily identifiable energy-like terms. A new method to derive non-standard Lagrangians for second-order nonlinear differential equations with damping is developed and the limitations of this method are explored. It is shown that the limitations do not exist only for those nonlinear dynamical systems that can be converted into linear ones. The obtained results are applied to selected population dynamics models for which non-standard Lagrangians and their corresponding null Lagrangians and gauge functions are derived, and their roles in the population dynamics are discussed.

Severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) is pandemic. Prevention and control strategies require an improved understanding of SARS-CoV-2 dynamics. We did a rapid review of the literature on SARS-CoV-2 viral dynamics with a focus on infective dose. We sought comparisons of SARS-CoV-2 with other respiratory viruses including SARS-CoV-1 and MERS-CoV. We examined laboratory animal, and human studies. The literature on infective dose, transmission, and routes of exposure was limited specially in humans, and varying endpoints were used for measurement of infection. We propose the minimum infective dose of COVID-19 in humans, is higher than 100 particles, possibly slightly lower than the 700 particles estimated for H1N1 influenza. Despite variability in animal studies, there was some evidence that increased dose at exposure correlated with higher viral load clinically, and severer symptoms. Higher viral load measures did not reflect COVID-19 severity. Aerosol transmission seemed to raise the risk of more severe respiratory complications in animals. An accurate quantitative estimate of the infective dose of SARS-CoV-2 in humans is not currently feasible and needs further research. Further work is also required on the relationship between routes of transmission, infective dose, co-infection, and outcomes.

The genetic diversity of foot-and-mouth disease virus (FMDV) poses a challenge to the successful control of the disease, and it is important to identify the emergence of different strains in endemic settings. The objective of this study was to evaluate sampling of clinically healthy livestock at slaughterhouses as a strategy for genomic FMDV surveillance. Serum samples (n = 11875) and oropharyngeal fluid (OPF) samples (n = 5045) were collected from asymptomatic cattle and buffalo on farms in eight provinces in southern and northern Vietnam (2015 to 2019) to characterize viral diversity. Outbreak sequences were collected between 2009 and 2019. In two slaughterhouses in southern Vietnam, 1200 serum and OPF samples were collected from asymptomatic cattle and buffalo (2017 to 2019) as a pilot study on the use of slaughterhouses as sentinel points of surveil-lance. VP1 sequences were analyzed using discriminant principal component analysis and time-scaled phylodynamic trees. Six of seven serotype O and A clusters circulating in southern Vietnam from 2017-19 were detected at least once in slaughterhouses, sometimes pre-dating outbreak sequences associated with the same cluster by 4-6 months. Routine sampling at slaughterhouses may provide timely and cost-effective strategy for genomic surveillance to identify circulating and emerging FMDV strains.

This paper examines the relationship between the ratio of independent board member to the financial performance of the company under the mediation of the three pillars of environment, society, and governance (ESG) in Taiwan. The study addresses a research gap between independent directors and corporate financial performance, an issue that is rarely discussed today. The author develops the hypotheses and tests them by applying panel data regression to the data tables taken from the Thomson Reuters Eikon database to analyze data on 173 Taiwanese companies that reported ESG from 2009 to 2021. The results show that the relationship between the ratio of independent directors and financial performance has a positive relationship. At the same time, the 3 pillars of ESG also clearly show the intermediary role in this relationship. Finally, this study provides additional insights into the relationship between the ratio of independent directors and financial performance in the Taiwan context.

The Lagrangian formalism is developed for the population dynamics of interacting species that are described by several well-known models. The formalism is based on standard Lagrangians, which represent differences between the physical kinetic and potential energy-like terms. A method to derive these Lagrangians is presented and applied to selected theoretical models of the population dynamics. The role of the derived Lagrangians and the energy-like terms in the population dynamics is investigated, and it is shown that the obtained standard Lagrangians can be used to study oscillatory behavior of the models and the period of their oscillations, which may have ecological and environmental implications. These and other physical and biological insights gained from the derived standard Lagrangians are discussed.

In this study, effects of molecular structure transformation of canna starch (CS) in oxidation condition on physicochemical characteristics of thermoplastic starch were examined. Thermoplastic starch (TPS) samples of CS and respective oxidized starch (in 1, 3 and 5% of sodium hypochlorite, w/w) were prepared by using an internal mixer with the presence of 30 wt% of glycerol as plasticizer. The physicochemical, morphological, thermal, and mechanical properties of native starch-based TPS (NTPS) and oxidized starch-based TPS (OTPS) samples were evaluated. The content of carboxyl and carbonyl groups in oxidized canna starch (OCS) increased with the increase in the content of oxidant, leading to an improvement in the plasticization of CS. FTIR spectra of OTPS samples showed the stronger interaction between oxidized starch and plasticizer. SEM images of fracture surface indicated that the morphology of OTPS samples were smoother than that of NTPS samples. XRD patterns confirmed that the crystallite type of starches was also clearly changed after extrusion process and the decrease in crystallinity of OTPS samples is attributed to effects of both oxidation and plasticization. DSC results indicated that Tg of OTPS was greatly influenced by the carbonyl and carboxyl content and the higher content of these groups in oxidized starched could help the plasticization becomes easier. The better plasticization in OTPS samples resulted in the better mechanical properties and thermal stability of OTPS. The outcome suggested that the use of oxidized starch is an effective method to improve the plasticization in preparing thermoplastic starch.

Innovation in general education governance is one of the development trends not only in Vietnam but also in the world. This is also an important measure to change and improve the quality of education, especially expand autonomy of high schools and universities. The paper focuses on some main contents: overview of general education; the experiences of some countries in the implementation of the school administration model towards the school autonomy model so that give lessons for Vietnam’s education can be learned in the context of development conditions nowadays. The results in this work would be used to classify the schools into the various groups. The data also analysts on decision-making capability, on what we called an “index of school autonomy”, expressed the possible level of school-level decision-making.

The risks for complications of severe acute respiratory syndrome coronavirus 2 (SARS-CoV2) infection are higher in obese individuals. Obesity is a state of chronic low-grade inflammation, with high leptin levels due to leptin resistance, high basal levels of other pro-inflammatory cytokines such as TNF-alpha, MCP-I and IL-6, and low adiponectin levels, thus contributing to a state of defective innate immunity as well as impaired B and T cell responses. Obesity is a risk factor for metabolic syndrome, diabetes, cardiovascular disease and hypertension. It has been observed that pre-existence of these diseases confers a higher risk of severe SARS CoV2 infection as well as the need for intensive care; even below the age of 60 years if their body mass index (BMI) is greater than 30 kg/m2, and even more so if it is > 35 kg/m2. The metabolic factors contributing to the changes in altering the immune mechanisms in obese individuals and how this enhances the susceptibility to infection and development of serious SARS-CoV2 infection have been the subject of many debates. Future development of targeted therapy and guidelines will be benefited by greater understanding into these metabolic pathways.

Frequency combs (FCs)—spectra containing equidistant coherent peaks—have enabled researchers and engineers to measure the frequencies of complex signals with high precision thereby revolutionising the areas of sensing, metrology and communications and also benefiting the fundamental science. Although mostly optical FCs have found widespread applications thus far, in general FCs can be generated using waves other than light. Here, we review and summarise recent achievements in the emergent field of acoustic frequency combs (AFCs) including phononic FCs and relevant acousto-optical, Brillouin light scattering and Faraday wave-based techniques that have enabled the development of phonon lasers, quantum computers and advanced vibration sensors. In particular, our discussion is centred around potential applications of AFCs in precision measurements in various physical, chemical and biological systems in conditions, where using light, and hence optical FCs, faces technical and fundamental limitations, which is, for example, the case in underwater distance measurements and biomedical imaging applications. This review article will also be of interest to readers seeking a discussion of specific theoretical aspects of different classes of AFCs. To that end, we support the mainstream discussion by the results of our original analysis and numerical simulations that can be used to design the spectra of AFCs generated using oscillations of gas bubbles in liquids, vibrations of liquid drops and plasmonic enhancement of Brillouin light scattering in metal nanostructures. We also discuss the application of non-toxic room-temperature liquid-metal alloys in the field of AFC generation.

(1) Background: This study aimed to evaluate the role of cervical pessary for preventing preterm birth in singleton pregnant women with a cervical length (CL) ≤25 mm and a uterocervical angle (UCA) ≥95o and ≥105o. (2) Methods: A quasi-experimental study was conducted on 225 singleton pregnant women with a gestational age of 16+o-23+6 weeks and transvaginal ultrasound CL measurements ≤25 mm, whose pregnancy was man-aged at the Haiphong Hospital of Obstetrics and Gynecology, Vietnam, from September 2020 to September 2022. Participants were allocated into two groups: prophylactic treatment with progesterone (123 pregnant women) and combined with a cervical pessary (102 pregnant women). The UCAs measured via transvaginal ultrasound by a single sonographer were divided into groups with UCA measurements ≥95o and ≥105o. The gestational age at birth was classified into full-term and preterm <37 weeks and <34 weeks. A binary regression model assessed the association between CL, UCA, and pre-term birth outcomes. The difference was statistically significant, with p<0.05. (3) Results: There was no statistically significant difference in the rate of preterm birth <37 weeks and <34 weeks between the two groups (16.3% vs. 11.8% and 6.5% vs. 4.9%, p>0.05). The probability of preterm birth <37 weeks in the group of pregnant women with a UCA ≥95o treated via cervical pessary plus progesterone decreased by 60.6%, OR (95% CI) of 0.394 (0.165-0.941), p<0.05. In the group of pregnant women with a UCA ≥105o, there was a significant association in the group of progesterone treatment combined with a cervical pessary, with the lower rate of PTB <37 weeks and <34 weeks, with OR (95% CI) of 0.028 (0.005-0.146), p<0.001, and 0.141 (0.030-0.664), p<0.05, respectively. (4) Conclusion: The results of this study suggest that cervical pessary is beneficial to the prevention of preterm birth in singleton pregnant women with an obtuse uterocervical angle. Further randomized studies among pregnant women with obtuse uterocervical angles will be needed to clarify the role of a cervical pessary in preventing preterm birth.

The construction industry plays a crucial role in shaping the built environment and contributes to the global economy. However, the construction process is associated with negative impacts on the environment and communities. This paper examines the environmental impacts of construction and presents strategies for mitigating them, focusing on sustainable construction practices. The research draws on a comprehensive literature review, case studies, and expert interviews to fully understand the construction industry and its environmental effects. The findings indicate that the implementation of greater supervision of every construction project phase, using alternative design practices, and the use of sustainable construction practices can reduce the negative impacts of construction on the environment and society. The study concludes that sustainable construction practices can contribute to a better environment for a better quality of life and should be embraced by the construction industry. The recommendations for future work include the adoption of green building standards, the use of renewable energy sources, the reduction of waste, and the promotion of stakeholder engagement. Future research should focus on the evaluation of the effectiveness of these strategies and their scalability.

Optical wireless communication is a promising emerging technology that addresses the limitations of radio-frequency-based wireless technologies. This study presents a novel hybrid modulation for optical camera communication (OCC); it integrates two waveforms transmitted from a single transmitter light-emitting diode (LED) and received by two rolling-shutter camera devices. Then, a smart camera with a high-resolution image sensor captures the high-frequency signal, and a low-resolution image sensor from a smartphone camera captures the low-frequency signal. Through this hybrid scheme, two data streams are transmitted from a single LED lamp; this reduces the cost of the indoor OCC device compared to one that transmits two signals from two different LEDs. In proposed scheme, rolling-shutter orthogonal frequency-division multiplexing is used for the high-frequency signals, and M-ary frequency-shift keying is used for the low-frequency signals in the time domain. This proposed scheme is compatible with smart phone camera and USB camera. By controlling the OCC parameters, the hybrid scheme can be implemented with high performance for a communication distance of 10 m.

This article aims to identify the current development of cross-border tourism between Vietnam and China. The paper analyzes the perception and strategy of cross-border tourism development in the two countries, especially in the context of China’s implementation of the “Belt and Road Initiative” (BRI). The article emphasizes that Vietnam and China have recently made efforts to promote cross-border tourism development. At the same time, Vietnam and China see cross-border tourism development as a significant part of comprehensive border cooperation between the two countries. However, the development plans for cross-border tourism between the two countries are still mainly on the desk, not yet implemented effectively. Thus, its achievements are relatively modest. Besides, the article emphasizes that the interests of the people living in the border area, especially the Vietnam side, are almost “forgotten” in the development of cross-border travel between the two countries. Besides, the article also analyzes the challenges that the two sides are facing, especially the Vietnam side, in promoting the development of cross-border tourism between the two countries.

Extravasation, the unintended leakage of intravenously administered substances, poses significant challenges in cancer treatment, particularly during chemotherapy and radiotherapy. This comprehensive review explores the pathophysiology, incidence, risk factors, clinical presentation, diagnosis, prevention strategies, management approaches, complications, and long-term effects of extravasation in cancer patients. It also outlines future directions and research opportunities, including identifying gaps in current knowledge and proposing areas for further investigation in extravasation prevention and management. Emerging technologies and therapies with the potential to improve extravasation prevention and management in both chemotherapy and radiotherapy are highlighted. Such innovations include advanced vein visualization technologies, smart catheters, targeted drug delivery systems, novel topical treatments, and artificial intelligence-based image analysis. By addressing these aspects, this review not only provides healthcare professionals with insights to enhance patient safety and optimize clinical practice but also underscores the importance of ongoing research and innovation in improving outcomes for cancer patients experiencing extravasation events.

In emergency scenarios service vehicles must identify potential route(s) and use the best available route. However, route identification requires intelligent decision-support systems which generally use non-traditional approaches with tools characterised by flexible non-hierarchical structures. Conventional models using group decision-support systems have been applied; however, when used in smart urban environments, emergency response services have limitations in their ability to identify unobstructed paths (routes) in dynamic operating environments. In this paper we introduce a novel path planning method for autonomous vehicle control in emergency situations. The proposed model uses self-organizing maps in an integrated Spiral STC algorithm termed the: Hybrid SOM-Spiral STC model which uses hedge algebras and \emph{Kansei} evaluation in group decision-support. The proposed model has been designed to quantify qualitative factors using sensor derived data processed with human sensibilities and preferences in emergency decision support. The experimental results show that the proposed model achieves significant improvements in group decision-support under dynamic uncertainty. We posit that our novel approach holds the prospect of improvements in the provision of emergency services.

Robotic decision-support systems must facilitate a robots interactions with their environment, this demands adaptability. Adaptability relates to awareness of the environment and `self-awareness', human behaviour exemplifies the concept of awareness to arrive at an optimal choice of action or decision based on reasoning and inference with learned preferences. A similar conceptual approach is required to implement awareness in autonomous robotic systems which must adapt to the current dynamic environment (the context of use). By incorporating `self-awareness' with knowledge of a Robot's preferences (in decision making) the decision maker interface should adapt to the current context of use. This paper proposes a novel approach to enable an autonomous robotics which implements path planning combining adaptation with knowledge reasoning techniques and hedge algebra to enable an autonomous robot to realise optimal coverage path planning under dynamic uncertainty. The results for a cleaning robot show that using our proposed approach demonstrated the capability to avoid both static and dynamic obstacles while achieving optimal path planning with increased efficiency. The proposed approach achieves the multiple decision-making objectives (path planning) with a high-coverage and low repetition rates. Compared to other current approaches, the proposed approach has demonstrated improved performance over the conventional robot control algorithms.

In this paper, the seven traditional models of PV modules are reviewed comprehensively to find out the appropriate model to be reliable. All the models are validated using the Matlab code and make a graphical comparison. The accuracy and convergence of each model are evaluated using data of manufactured PV panels. Then, a novel model is proposed showing its consistent performance. The most three key parameters of single-diode model are self revised to adapt to various type of PV modules. This new method is verified in three types of PV panels' data measured by National Renewable Energy Laboratory (NREL), US. The validated data show promising results when the error RMSEs' range of the proposed model is under 0.36.

In the era of the post-quantum Internet of Things (IoT), the implementation of anti-quantum cryptographic algorithms in numerous terminals can successfully defend against prospective quantum computing assaults. Lattice-based cryptography can withstand quantum computing attacks, making it a viable substitute for the currently prevalent classical public-key cryptographic technique. Nevertheless, the algorithm’s significant time complexity will result in a substantial computational burden on the edge computing chip in the IoT terminal. The computation of polynomial multiplication is the most demanding task in lattice-based cryptographic algorithms. Therefore, the investigation into efficient methods for calculating polynomial multiplication is highly important. Quick number theory transformations (NTT) are a widely employed technique to accelerate polynomial multiplication. This study presents a hardware implementation of an efficient number theory transformation. We utilize a multi-level pipeline architecture in the design to accomplish parallel calculations and execute it on a low-profile Artix7-XC7A100T FPGA device. The performance evaluation results demonstrate that our implementation significantly enhances performance and reduces resource usage compared to other existing proposals on the same platform. We suggested NTT core can be implemented in edge computing chips to enhance computational speed due to its small and low-latency design. The experimental results show that the proposed design, which supports both NTT and inverse NTT, achieves 417-Megahertz and consumes only 541-LUTs on Artix-7 XC7A100T.

A feeding study was conducted to evaluate the different diets supplemented with vitamin solution effect on broodstock reproduction, growth performances, and the survival rates of larvae and fry of Pangasius catfish during over-spawning season. The experiment of broodstock cultivation was set up as a diet supplement design with six different diets consisting of vitamin solution, each diet fed to triplicate groups of fish, the stocking density of 10 broodstock fish (07 females and 03 males) per hapa net. Fish larvae and fry were reared in the hatchery for 45 days after hatching to evaluate growth performances and survival rates of fish fingerling. The growth and reproductive performances of breeders fed with different test diets showed that there were differences among the six tested diets (P < 0.05). The highest final body weight (FBW), weight gain (WG), daily weight gain (DWG), specific growth rate (SGR) of broodstock and survival rate of Pangasius fingerlings were found in Treatment 5, which contained 0.6% H-OVN for Pangasius Broodstock mixed with 12.6% algal oil and Treatment 3, which contained 0.6% vitamin premix H-OVN for Pangasius Broodstock compared to other Treatments. With these test diets, the Gonadosomatic index (GSI), relative fecundity index (RFI), fertilized egg, hatching rates of eggs, and survival rate of fingerling ranged between a 6.7–12.8%, 104,267–199,512 eggs/kg, 62.2–93.6%, 43.5–76.2%, and 45.3–66.3%, respectively (P < 0.05). The findings of this study showed that the diet containing 35% CP contents supplemented with 0.6% vitamin premix H-OVN mixed with algal oils showed the highest results in terms of growth, reproductive performance indices, and survival rates of Pangasius catfish fingerling.

This article presents a wide-band antenna designed for the Cube Satellite (CubeSat). Based on a quadrifilar structure, the antenna provides circular polarization radiation, which is suitable for satellite communication. Moreover, the antenna is designed and fabricated using two 1.6 mm thickness FR4-Epoxy boards that connect together by the metal pins. In order to improve the robustness, a ceramic spacer is placed in the centerboard, and four screws at the corners are added to fix the antenna with the CubeSat structure. These additional parts reduce antenna damage caused by vibrations in the launch vehicle lift-off stage. The proposal has a dimension of 77mm x 77mm x 10mm and covers the LoRa frequency bands of 868 MHz, 915 MHz, and 923 MHz. According to the measurements in an anechoic chamber, antenna gains are obtained with the values of 2.3 dBiC and 1.1 dBiC for the 870 MHz and 920 MHz, respectively. Finally, the antenna is integrated into a 3U CubeSat that was launched by a Soyuz launch vehicle. The terrestrial-to-space communication link was measured, and the antenna performance was confirmed in the real-life scenario.

In Vietnam, general education includes primary education, lower secondary education (the period of basic education) and upper secondary education (the period of vocational orientation education). In particular, primary education is compulsory for all children from 6 to 14 years old, is implemented in 5 school years, from first grade to fifth grade. The age of students entering first grade is six years old. Primary education aims to help students form the initial foundations for proper and long-term development of morality, intelligence, physicality, aesthetics and basic skills for students to continue high school. Secondary education is conducted in four school years, from grade six to grade nine. Students entering sixth grade must have an elementary school diploma. Secondary education aims to help students consolidate and develop the results of primary education; have basic secondary education and initial knowledge about technology and career to continue high school, vocational high school, vocational training or enter a working life. High school education is conducted in 3 school years, from grade ten to grade twelve. Students entering tenth grade must have a junior high school diploma. High school education is aimed at helping students consolidate and develop the outcomes of lower secondary education, complete high school education and common knowledge about technology and career guidance for further college education, college, professional secondary school, apprenticeship or enter the working life. Thus, the term general education is a term with broad connotation including primary education, lower secondary education (basic education period) and upper secondary education (education period) career orientation. Within the scope of this research, we use the term school governance used to mean a mode of action, which is directed toward the goal of being accomplished effectively, by and through others. Governance activities are indispensable activities that arise when people work together to accomplish goals.

Enhancing the effectiveness of search and rescue operation at sea is always a duty of utmost importance of the coastal states. The search area for distressed objects can be determined by using Monte Carlo simulation, combined with the Median-Filter. Once the search area has been identified, the success of search and rescue operations depends on the sweeping ability of search and rescue vessel at the probability area of the distress object with the minimum time. This is the important element to the success of the search and rescue operation as it minimizes the risk and cost for Search and rescue team. In this article, the authors study and propose the use of Bacterial Foraging Optimization Algorithm (BFOA) to calculate the optimal search and co-ordination route for many search and rescue vessels in Vietnam sea. The simulation results show that it is quite consistent with reality and BFOA can be effectively applied to determine a quick search.

Intrinsic and extrinsic sensory elements influence our food experiences. However, most research in extrinsic multisensory aspects of food has centered on WEIRD (White, Educated, Industrialized, Rich, and Democratic) urban participants. This study breaks from this by investigating multisensory eating experiences in the context of Northern Norway, a region characterized by distinct seasonal shifts, harsh arctic weather, unique atmospheric phenomena (e.g., the midnight sun and northern lights), limited food growth opportunities, and a rich Sámi cultural heritage. Our exploratory research used participant observation and interviews, involving four researchers from diverse backgrounds who closely examined multisensory food experiences within four Northern Norwegian food-related tourism businesses, all infused with Sámi cultural elements. Four themes emerged: 1) Experience elements, involving elements associated with plants, animals, and non-animate objects. 2) Bipolar concepts, which refer to contradicting dimensions where experience elements varied, notably in the interplay between Sámi and Norwegian traditions. 3) Sensory stories, which highlight the narratives, enriching the eating experience with context, such as tales of dining under the captivating northern lights. 4) Values which indicate guiding principles shaping these experiences on a broader scale, emphasizing support for local traditions and culture. Our main contribution is the presentation of a new contextual framework of multisensory eating experiences which can be applicable to studying eating experiences in other contexts.

In today’s fast paced, attention-demanding society, executive functions and attentional resources are often taxed. Individuals need ways to sustain and restore these resources. We first review the concepts of attention and restoration, as instantiated in Attention Restoration Theory (ART). ART emphasizes the role of nature in restoring attention. We then discuss essentials of experiments on the causal influences of nature. Next, we expand the concept of ART to include modern, designed environments. We propose a wider perspective termed attentional ecology, in which attention behavior is viewed within a larger system involving the human and their interactions over time with environmental demands. When the ecology is optimal, mental functioning can be a positive “flow” that is productive, sustainable for the individual, and sometimes creative.

Regulatory macrophages (Mregs) are unique in that they have anti-inflammatory and immunosuppressive properties. Thus, treating inflammatory diseases using Mregs is an area of active research. Human Mregs are usually generated by culturing peripheral blood monocytes stimulated by macrophage colony-stimulating factor with interferon (IFN)-. Here, we generated Mregs with an elongated cell morphology from THP-1 cells stimulated with phorbol 12-myristate 13-acetate and cultured with arginylglycylaspartic acid and vitamin D3. These Mregs regulated macrophage function, and respectively downregulated and upregulated the expression of pro-inflammatory and immunosuppressive mediators. They also expressed Mregs-specific marker, such as dehydrogenase/reductase 9, even when exposed to inflammatory stimulants such as IFN-, lipopolysaccharide, purified xenogeneic antigen, and xenogeneic cells. The Mregs also exerted anti- inflammatory and anticoagulatory actions in response to xenogeneic cells and immunosuppressive effects on mitogen-induced Jurkat T-cell proliferation. Our method of generating functional Mregs in vitro without cytokines is simple and cost-effective.

The study examines the behavior of the Mechanically Stabilized Earth (MSE) wall using available reinforcement materials in Danang, Vietnam. The MSE was reinforced by the self-fabricated galvanized steel grids using CB300V steel with 3 cm ribs. The backfill soil is a sandy clay soil from the local area with a low cohesion. A full-scale model with full instrumentation was installed to investigate the distribution of tensile forces along the reinforcement layers. The highest load that caused the wall to collapse due to internal instability (reinforcement rupture) was 302 kN/m2, which is 15 times the design load of 20 kN/m2. The failure surface within the reinforced soil had a parabolic sliding shape which is similar to the theoretical studies. At the failure load level, the maximum lateral displacement at the top of the wall facing was small (3.9 mm) which is significantly lower than the allowable displacements for the retaining wall. Furthermore, a numerical model using FLAC software was applied to simulate the performance of the MSE wall. The modeling results are in good agreement with the physical model. Thus, the self-fabricated galvanized steel grids could be confidentially used in combination with the local backfill soil for the MSE walls.

The study aimed to compare the cardiovascular benefits of Omega-3 Polyunsaturated Fatty Acids from fish oil versus krill oil in different forms and dosages. Following PRISMA 2015, data analysis with R software, and databases were searched from 1993 to 2023, (ID PROSPERO: CRD42024502338). Sixty high-quality studies were analyzed, covering various forms of fish oil and krill oil at different dosages (fish oil (ethyl ester-EE, triglyceride-TG, re-esterified triglycerides-rTG, capsules, emulsion-EM); krill oil (phospholipid/free fatty acid-PL/FFA, high concentration phospholipid-HPL, low concentration phospholipid-LPL)). Meta-analysis revealed that krill oil with phospholipid/free fatty acid at doses 2000-2900 mg effectively lowered triglycerides, while fish oil in ethyl ester form at doses above 3000 mg significantly reduced total cholesterol. Fish oil in triglyceride form at doses 2000-2900 mg and other variations positively impacted HDL-C levels. Fish oil in EE form above 3000 mg and triglyceride form below 2000 mg notably reduced LDL-C. However, there was limited effectiveness observed for other interventions. Analysis for LDL-C exhibited publication bias, while other parameters demonstrated reliability (Egger's test). In conclusion, krill oil - PL/FFA, Fish oil - EE above 3000 mg, Fish oil - TG 2000-3000 mg, and fish oil - rTAG 300-1900 mg effectively in reducing heart risk patients.

We discuss what we believe could be an improvement in future discussions of the ever-changing brain. We do so by distinguishing different types of brain variability and outlining methods suitable to analyse them. We argue that, when studying brain and behaviour data, classical methods such as regression analysis and more advanced approaches both aim to decompose the total variance into sensible variance components. In parallel, we argue that a distinction needs to be made between innate and acquired brain variability. For varying high-dimensional brain data, we present methods useful to extract their low-dimensional representations. Finally, to trace potential causes and predict plausible consequences of brain variability, we discuss how to combine statistical principles and neurobiological insights to make associative, explanatory, predictive, and causal enquires; but cautions are needed to raise association- or prediction-based neurobiological findings to causal claims.

While the container crane is an important part of daily port operations, it has received little attention compared with other infrastructures, such as buildings and bridges. Crane collapse due to earthquake affects the operation of the port, and indirectly impacts the economy. This study proposes fragility analyses for various damage levels of the container crane that allow the port owner and partners to better understand the seismic vulnerability presented by container cranes. A large quantity of nonlinear time history analyses was applied for a three-dimensional (3D) finite element model to quantify the vulnerability of the container crane in considering the uplift and derailment behavior. The uncertainty of demand and capacity of the crane structures were also considered through random variables, i.e. elastic modulus of members, ground motion profile, and intensity. The results analyzed in the case of a Korean container crane showed that the probability of exceeding the first uplift with or without derailment is shown before the crane reaches the structure’s limit states. This means that under low seismic excitation, the crane might be derailed without any structural damage. But when the crane reaches the minor damage state, it is always coupled with a certain probability of uplift with or without derailment. This study also proposes the fragility curves developed for different structural periods to enable port stakeholders to assess the risk of their container crane.

Microstructured surfaces are renowned for their unique properties, such as waterproofing and low adhesion, making them highly applicable in the biomedical field. These surfaces play a crucial role in influencing cell response by mimicking the native microenvironment of biological tissues. In this study, we engineered a series of biomimetic micropatterned surfaces using polydimethylsiloxane (PDMS) to explore their effects on primary breast cancer cell lines, contrasting these effects with those observed on conventional flat surfaces. The surface topography was varied to direct cells’ attachment, growth, and morphology. Our findings elucidate that surface-free energy is not merely a background factor but plays a decisive role in cell dynamics, strongly correlating with the spreading behaviour of breast cancer cells. Notably, on micropillar surfaces with high surface-free energy, an increase in the population of cancer cells was observed. Conversely, surfaces characterised by lower surface-free energies noted a reduction in cell viability. Moreover, the structural parameters, such as the gaps and diameters of the pillars, were found to critically influence cellular dispersion and adherence, underscoring the importance of the microstructures’ topography in biomedical applications. These insights pave the way for designing advanced microstructured surfaces tailored to specific cellular responses, opening new avenues for targeted cancer therapies and tissue engineering.

Carbon nanotube (CNT) yarns are fiber-like materials that exhibit excellent mechanical, electrical and thermal properties. More importantly, they exhibit a piezoresistive response that can be tapped for sensing purposes. The objective of this study is to determine experimentally the piezoresistive response of CNT yarns that are embedded in a polymeric medium while subjected to either compression or tension, and compare it with that of the free or unconstrained CNT yarns. The rationale for this study is the need to know the response of the CNT yarn while in a medium, which provides a lateral constraint to the CNT yarn thus mimicking the response of integrated CNT yarn sensors. The experimental program will include the fabrication of samples and their electromechanical characterization. The CNT yarns are integrated in polymeric beams and subjected to four-point bending, allowing the determination of their response under tension and compression. The electrical resistance data from an Inductance-Capacitance-Resistance (LCR) device is used with the data acquired from the mechanical testing system to determine the piezoresistive response of the CNT yarns. This data and information will be used for future modeling efforts and to study the phenomena that occur when CNT yarns are integrated in polymeric and composite materials and structures.

Retiring coal power plants can reduce air pollution and health damages. However, the spatial distribution of those impacts remains unclear due to complex power system adjustments and pollution chemistry and transport. Focusing on coal retirements in Pennsylvania (PA), we analyze six counterfactual scenarios for 2019 that differ in retirement targets (e.g., reducing 50% of coal-based installed capacity vs. generation) and priorities (e.g., closing plants with higher cost, closer to Environmental Justice Areas, or with higher CO₂ emissions). Using a power system model of the PJM Interconnection, we find that coal retirements in PA shift power generation across PA and the Rest of PJM region leading to scenario-varying changes in the plant-level release of several air pollutants. Due to air pollution chemistry and transport and socio-demographics, these changes in turn give rise to a reduction of 10 to 182 PM_2.5-attributable deaths in PJM across the six scenarios, with most reductions occurring in PA. Scenarios that reduce more coal power generation yield greater aggregate health benefits due to air quality improvements in PA and adjacent downwind regions. In addition, vulnerable populations—in both PA and Rest of PJM—benefit most in scenarios that prioritize plant closures in PA near Environmental Justice Areas. These results demonstrate the importance of considering cross-regional linkages and socio-demographics in designing equitable retirement strategies.

There is an accelerating requirement for ocean sensing where autonomous vehicles can play an essential role in assisting engineers, researchers, and scientists with environmental monitoring and collecting oceanographic data. This paper is performed to develop a rigid sail for the autonomous sailing drone. Our study aims to numerically analyze the aerodynamic characteristics of curvy twin sail and compare it with wing sail. Because racing regulations limit the sail shape, only the two-dimensional geometry was open for an optimization. Therefore, this study’s first objective was to identify the aerodynamic performance of such curvy twin sails. Simultaneously, a secondary objective was to estimate the effect of the sail’s spacing and shapes. A viscous Navier-Stokes flow solver is used for the numerical aerodynamic analysis. The 2D aerodynamic investigation is a preliminary evaluation. The results have shown that the curvy twin sail designs have improved lift, drag, and driving force coefficient compared to the wing sails. The spacing between the port and starboard sails of curvy twin sail is an important parameter. The spacing is 0.035L, 0.07L, and 0.14L shows the lift coefficient reduction because of dramatically stall effect, while flow separation is improved with spacing is 0.21L, 0.28L, and 0.35L. Significantly, the spacing 0.28L shows the maximum high pressure at the lower area and the small low pressure area at leading edges, so the highest lift is generated.

The use of heart rate variability (HRV) in research has been greatly popularized over the past decades due to the ease and affordability of HRV collection, coupled with its clinical relevance and significant relationships with psychophysiological constructs and psychopathological disorders. Despite the wide use of electrocardiogram (ECG) in research and advancement in sensors technology, the analytical approach and steps applied to obtain HRV measures can be seen as complex. Thus, posing a challenge to users who may not have the adequate background knowledge to obtain the HRV indices reliably. To maximize the impact of HRV-related research and its reproducibility, parallel advances in users’ understanding of the indices and the standardization of analysis pipelines in its utility will be crucial. This paper addresses this gap and aims to provide an overview of the most up-to-date and commonly used HRV indices, as well as common research areas that these indices have shown to be very useful, particularly in psychology. In addition, we also provide a step-by-step guide on how to perform HRV analysis using an integrative neurophysiological toolkit, NeuroKit2.

The performance in terms of minimal Bayes’ error probability for detection of a high-dimensional random tensor is a fundamental under-studied difficult problem. In this work, we consider two Signal to Noise Ratio (SNR)-based detection problems of interest. Under the alternative hypothesis, i.e., for a non-zero SNR, the observed signals are either a noisy rank-R tensor admitting a Q-order Canonical Polyadic Decomposition (CPD) with large factors of size Nq  R, i.e, for 1  q  Q, where R, Nq ! ¥ with R1/q/Nq converge towards a finite constant or a noisy tensor admitting TucKer Decomposition (TKD) of multilinear (M1, . . . ,MQ)-rank with large factors of size Nq  Mq, i.e, for 1  q  Q, where Nq,Mq ! ¥ with Mq/Nq converge towards a finite constant. The detection of the random entries (coefficients) of the core tensor in the CPD/TKD is hard to study since the exact derivation of the error probability is mathematically intractable. To circumvent this technical difficulty, the Chernoff Upper Bound (CUB) for larger SNR and the Fisher information at low SNR are derived and studied, based on information geometry theory. The tightest CUB is reached for the value minimizing the error exponent, denoted by s?. In general, due to the asymmetry of the s-divergence, the Bhattacharyya Upper Bound (BUB) (that is, the Chernoff Information calculated at s? = 1/2) can not solve this problem effectively. As a consequence, we rely on a costly numerical optimization strategy to find s?. However, thanks to powerful random matrix theory tools, a simple analytical expression of s? is provided with respect to the Signal to Noise Ratio (SNR) in the two schemes considered. A main conclusion of this work is that the BUB is the tightest bound at low SNRs. This property is, however, no longer true for higher SNRs.

Nowadays, wearable devices for human health monitoring are increasingly become popular and widely used. Typically, the wearable device is small size and operates with batteries. Therefore, the wearable device acquires bio-signals and transfers to smartphones or personal computers (PC) via WiFi/ Bluetooth for processing data. To reduce power consumption is one of the most important challenges of designing wearable devices. To solve this problem, the proposed signal quality valuation (SQV) method can be select the high-quality signal and reduce the transfer time to other devices. In this paper, the proposed SQV and data compression method rely on real-time PPG signals analysis to retain important information of PPG signal, improve performance and power consumption of PPG devices. Besides, we also proposed Heuristic rules for heart rate (HR) estimation with compression data. The experimental results show that the highest compression ratio (CR) is 387.8 with BIDMC Physionet database (sampling frequencies of 125 Hz) and HR error as 1.43 bpm for averaging absolute error (avAE), the standard deviation absolute error (sdAE as 0.4) and relative error mean (avRE as 0.019). The proposed real-time PPG measurement system (sampling frequency as 100/ 200/ 400 Hz) reduce power consumption and open the new structure for healthcare application systems

Curcuma longa is only a rich source of curcumin (1) and its major analogues demethoxycurcumin (2) and bisdemethoxycurcumin (3) among the Curcuma species. The content ratio of these three curcumins in turmeric is depended on the varieties and growing environment. Recently, curcumin (1) has been reported as potential inhibitor of hepatic and enzymatic protein tyrosine phosphatase 1B (PTP1B) and its related disorders such as hypertriglyceridemia, hyperlipidemia and liver steatosis. Thus, we further purified curcumins (1–3) from C. longa and investigated their inhibitory effects against PTP1B and α-glucosidase enzymes. As the result, curcumins (1–3) exhibited potential PTP1B inhibition with IC50 values of 37.8 ± 1.4, 45.3 ± 0.7, and 72.6 ± 1.1 μM, respectively, and α-glucosidase inhibition with similar manner (IC50 values of 78.2 ± 0.2, 82.4 ± 0.6, and 90.6 ± 1.0 μM, respectively). These results reveal a key role of methoxylation in the variation of PTP1B and α-glucosidase inhibitory activity for these curcumins. In addition, density functional theory (DFT) was used accompanying with molecular docking (MD) to analyze the ligand stability and the interaction of curcumins (1–3) with PTP1B and glucoside hydrolase proteins. Assay-based results and the MD data obtained are highly correlation suggesting that the deterioration of the enzyme activity caused by the distortion of structural conformation of PTP1B and glucoside hydrolase may be related to the arrangement of amino acids in protein structure. This reported for the first time that inhibitory effects of curcumins (1–3) against PTP1B and glucoside hydrolase have been examined in vitro and in silico as well.

In considering knowledge graphs in a diverse range of domains of interest, graph neural networks have demonstrated significant improvements in node classification and prediction when applied to graph representation with learning node embedding to effectively represent hierarchical properties of graphs. DiffPool is a deep-learning approach using a differentiable graph pooling technique that generates hierarchical representations of graphs. In operation DiffPool is a differentiable graph pooling technique that generates hierarchical representations of graphs. DiffPool learns a differentiable soft cluster assignment for nodes at each layer of a deep graph neural network with nodes mapped sets of clusters. However, control of the learning process is difficult given the complexity and large number of parameters on an `end-to-end’ model. To address this difficulty we propose an novel approach termed FPool which is predicated on the basic approach adopted in DiffPool (where pooling is applied directly to node representations). Methods designed to enhance data classification have been developed and evaluated using a number popular and publicly available sensor data sets. Experimental results for FPool demonstrate improved classification and prediction performance when compared to alternative methods. Moreover, FPool shows an important reduction in the training time over the basic DiffPool framework.

Robotic path planning is a field of research which is gaining traction given the broad domains of interest to which path planning is an important systemic requirement; the aim being to optimise the efficacy of robotic movements in a defined operational environment. For example, robots have been employed in many domains including: cleaning robots (such as vacuum cleaners), automated paint spraying robots, window cleaning robots, forest monitoring robots, agricultural robots (often driven using satellite and geostationary positional satellite data). Additionally, mobile robotic systems have been utilised in disaster areas and locations hazardous to humans (such as war zones in mine clearance). The coverage path planning problem describes an approach which is designed to determine the path that traverses all points in a defined operational environment while avoiding static and dynamic (moving) obstacles. In this paper we present our proposed Smooth-STC model, the aim of the model being to identify an optimal path, avoid all obstacles, prevent (or at least minimise) backtracking, and maximise the coverage in any defined operational environment. The experimental results in a simulation show that, in uncertain environments, our proposed smooth STC method achieves an almost absolute coverage rate and demonstrates improvement when measured against alternative conventional algorithms.

The main focus when developing software is to improve the reliability and stability of a software system. When software systems are introduced, these systems are used in field environments that are the same as or close to those used in the development-testing environment; however, they may also be used in many different locations that may differ from the environment in which they were developed and tested. In this paper, we propose a new software reliability model that takes into account the uncertainty of operating environments. The explicit mean value function solution for the proposed model is presented. Examples are presented to illustrate the goodness-of-fit of the proposed model and several existing non-homogeneous Poisson process (NHPP) models and confidence intervals of all models based on two sets of failure data collected from software applications. The results show that the proposed model fits the data more closely than other existing NHPP models to a significant extent.

Marketing is one of the important stages, the decisive factor affecting the success of production and business activities of every business. Therefore, marketing is considered to be the first and most important stage in the process of introducing, bringing products to market and branding of businesses, especially in the period when the disease situation is taking place very complicated worldwide. This study provides both qualitative and quantitative results for the following research objectives. Firstly, the study will assess the situation and analyze the appropriateness of marketing models in the current market situation trend. Secondly, the study proposes an approach in building a new type of marketing model, which is 3D web-based marketing applied in e-commerce to support the modeling of enterprise products in the form of Interactive 3D products are similar to real products. Thirdly, testing and evaluating 3D e-commerce web marketing model at Truong Hai Auto Showroom, Thai Nguyen City branch. This study also proposes a number of solutions for the research and deployment of 3D web marketing model application for businesses in the current market situation.

Land-use planning plays an important role in agricultural development, however it lacks tools to support planner in proposing land-use planning solutions especially, under saltwater intrusion condition in the coastal regions. This study aims to apply optimization in analyzing land-use solutions for agricultural land-use planning. In which a multi-objective optimization model is developed to optimize land-use area including land-use allocation taking into account socio-economic and environmental factors. The model has been applied in three districts of Soc Trang province, Vietnam (Long Phu, My Xuyen and Tran De) representing three ecological regions including salt water, brackish water and freshwater in the Mekong Delta of Vietnam. The results showed that two multi-objective optimization scenarios (in terms of profit, labor, environment benefits and risk reduction) have been implemented: (i) Multi-objective optimization of agricultural land-use until 2030 under normal conditions; (ii) Optimizing agricultural land-use until 2030 under climate change conditions similar to the 2016 drought and saltwater intrusion phenomenon in the Mekong Delta. The results showed that the second scenario is the option considered for implementing land-use plan thanks to the balance between good profits and minimizing economic and environmental risk. The land allocation was carried out taking into account household economic, the influence of adjacent production types, local traffic and canal systems factors to allocate optimal land-use areas. The combination of land-use optimization and spatial allocation process can help planners improve the quality of agricultural land-use planning.

Burn injuries have profound implications for aesthetics, functionality, and patient survival. Umbilical cord lining mesenchymal stem cells (SCL-MSCs) have emerged as a potential therapeutic approach for burn wounds due to their easy isolation, favorable differentiation capabilities, and low immunogenicity. This study aimed to evaluate the growth characteristics of SCL-MSCs and their effectiveness in treating burn wounds. Mechanical isolation was employed to extract mesenchymal stem cells from the umbilical cord lining membrane. The isolated cells underwent characterization, including analysis of HLA-E, G, and DR expression, and assessment of immunogenicity against rabbit antigens using ELISA. A rabbit model was utilized to administer burn treatment. SCL-MSCs exhibited typical morphology of mesenchymal stem cells and demonstrated robust proliferation. These cells expressed CD90, HLA-E, and HLA-G markers while lacking HLA-DR expression. Intact cells and supercrushed cell fluid displayed minimal and unstable immunogenicity. SCL-MSCs exhibited remarkable differentiation potential toward fibroblast lineages, with differentiated fibroblasts showing elevated collagen production and efficient sheet formation. In the experimental rabbit model, burn wounds covered with SCL-MSC tegaderm material plates exhibited superior healing compared to controls. The stem cell material plate area demonstrated reduced inflammatory cell counts (P &lt; 0.01) and increased fibroblast count, neovascularization, and mitotic index (P &lt; 0.01). These findings highlight the potential of SCL-MSCs as a valuable resource for burn wound research and treatment.

Background. There is limited evidence on the relationship between chronic kidney disease (CKD) and frailty in older people in Vietnam. This study aimed to examine the prevalence of frailty and its impact on mortality in older patients with end-stage renal disease. Method. This is a prospective, observational study at two large Dialysis Centres in Vietnam from November 2020 to June 2021. Consecutive older patients diagnosed with end-stage renal disease and on dialysis were recruited. Participants’ frailty status was defined by the Clinical Frailty Scale (CFS). The study outcome was all-cause mortality at 6th month. Results. A total of 175 participants were recruited (mean age 72.4 years, 58.9% female). Using the cut-point of CFS ≥4, 87.4% of the participants were frail. Mortality at 6th month was 14.9%, 31.9% in participants with CFS ≥7, 12.8% in participants with CFS=6, 7.5% in participants with CFS from 4 to 5, and 4.5% in participants with CFS ≤3 (p=0.001). Cox regression analysis showed that compared to the non-frail participants, the probability of death over 6 months was nearly 2-fold higher in the mildly frail, 3-fold higher in the moderately frail, and 9-fold higher in the severely frail participants. Conclusion. This study demonstrated a very high prevalence of frailty in older patients with end-stage renal disease and dialysis and the significant impact of frailty severity on mortality. Healthcare providers should consider incorporating frailty screening into routine care for older patients with end-stage renal disease and dialysis.

The study aims to evaluate the impact of organizational culture on labor efficiency at foreign-invested logistics service enterprises that are on its ways towards business sustainability. The authors develop theoretical basis on organizational culture and explore factors that contribute to organizational culture and labor efficiency; from which 03 research hypotheses are proposed. Primary data are collected from logistics businesses through questionnaires; multiple linear regresion model is used to analyze the influence of organiational culture on labor effeciency at foreign-invested logistics enterprises. Research results indicate 05 factors of organizational culture contribute positive impact on employee productivity, including employees’ trust, company ideals, leadership styles and authority division, business philosophy and mission, people’s relationship with naturual environment. Based on the research results, proposed recommendations are suggested for improving labor efficiency at foreign-invested logistics service enterprises in a sustainable way.

Damage assessment is one of the most crucial issues for bridge engineers, especially for existing steel bridges. Among several methodologies, the vibration measurement test is a typical approach in which the natural frequency variation of the structure is monitored to detect the existence of damage. However, locating and quantifying the damage is still a big challenge. In this regard, the artificial intelligence (AI)-based approach seems a potential way to accomplish those obstacles. This study deploys a comprehensive campaign to determine all dynamic parameters of a pre-damage steel truss bridge structure. Based on the results of mode shape, natural frequency, and damping ratio, a finite element model (FEM) is created and keeps updating. The artificial intelligence network's input data will be analyzed and evaluation from damage cases. The trained artificial neural network model will be curated and evaluated to confirm the approach's feasibility. During the actual operational stage of the steel truss bridge, this damage assessment system is showing good performance in terms of monitoring the structural behavior of the bridge under some unexpected accidents.

Changing climate conditions and rapidly increasing carbon dioxide emissions have severely affected the global ecosystem and world economy. Governments around the world have paid attention to these resulting challenges and enacted many policies to reduce environmental pollution and carbon dioxide (CO2) emissions. This study aimed to determine and understand the relationship between innovation, foreign direct investment, economic growth, renewable consumption and CO2 emission in Vietnam. Information was collected annually based on the annual data of the General Statistics Office of Vietnam and World Bank from 2000 to 2022. Data processing was conducted using the STATA 17.0 software. The innovation affects Vietnam’s environmental pollution. Innovation positively affect environmental pollution in Vietnam; if Vietnam’s innovation were to increase by 1%, CO2 emissions would increase by 0.68%. The empirical research results of this study also show that renewable energy consumption has a negative effect on environmental pollution in Vietnam; if renewable energy were consumed at a 1% increase, CO2 emission would decrease by 0.51%. In addition, FDI inflows and economic growth have strongly positive affecting to environmental pollution; if Vietnam’s FDI inflows were to increase 1%, CO2 emissions would increase 1.39%; if Vietnam’s GDP increase 1% then CO2 emission would increase 1.26%. This paper also provides some recommendations that can assist Vietnam in developing a green and sustainable economy in the technology revolution 4.0 to achieve the United Nations Sustainable Development Goals (SDGs) over a long-term period.

Rapid advancements in the fifth generation (5G) communication technology and mobile edge computing (MEC) paradigm lead to the proliferation of unmanned aerial vehicles (UAV) in urban air mobility (UAM) networks, which provide intelligent services for diversified smart city scenarios. Meanwhile, the widely deployed internet of drones (IoD) in smart cities also brings up new concerns on performance, security, and privacy. The centralized framework adopted by conventional UAM networks is not adequate to handle high mobility and dynamicity. Moreover, it is necessary to ensure device authentication, data integrity, and privacy preservation in UAM networks. Thanks to characteristics of decentralization, traceability, and unalterability, Blockchain is recognized as a promising technology to enhance security and privacy for UAM networks. In this paper, we introduce LightMAN, a lightweight microchained fabric for data assurance and resilience-oriented UAM networks. LightMAN is tailored for small-scale permissioned UAV networks, in which a microchain acts as a lightweight distributed ledger for security guarantees. Thus, participants are enabled to authenticate drones and verify the genuineness of data that is sent to/from drones without relying on a third-party agency. In addition, a hybrid on-chain and off-chain storage strategy is adopted that not only improves performance (e.g,.latency and throughput) but also ensures privacy preservation for sensitive information in UAM networks. A proof-of-concept prototype is implemented and tested on a Micro Air Vehicle Link (MAVLink) simulator. The experimental evaluation validates the feasibility and effectiveness of the proposed LightMAN solution.

High rates of phosphorus (P) currently being applied to soils for the production of vegetables in the Mekong Delta, Vietnam has led to the concern of its negative effect on the economics and the environment. This research presents a comprehensive study on the determination of P supplying capacity in this region of Vietnam to examine the possibility of reducing P fertilizer input. One hundred twenty (120) soil samples were collected to evaluate total P and Bray 1 available P in the soils. Phosphorus maximum sorption, degree of P saturation, P release, and the effect of P fertilizer on corn (Zea mays L.) yield in greenhouse and fields were also determined. Total P concentrations of 56.7% soil samples evaluated yielded high P concentrations (>560 mg P/kg), while 74.2% of the samples had high Bray 1 available P concentrations (>20 mg P/kg soil). Maximum P sorption ranged from 149 to 555 mg P/kg soil, respectively and has negative correlation to available P (r = - 0.63*), degrees of P saturation ranged from 0.63 to 5.46% correlated to available P (r = 0.98**) and maximum P release ranged from 1.2 to 61.9 mg P/kg soil, respectively correlated to available P (r = 0.96**). Corn grown in soils with available P concentrations >15 mg P/kg did not respond to P fertilizer in greenhouse or field experiments. We conclude that many farmers in this region can reduce P fertilizer input, thus increasing their profits and reducing negative environmental impacts associated with excess soil P for sustainable agriculture.

The advent of the era of big data will bring more convenience to people and greater development to society. But at the same time, it will also bring people the problem of 'information overload', i.e., when people are faced with huge information data, there are many redundant and worthless data. The redundant and worthless data information seriously interferes with the accurate selection of information data. Even though people can use Internet search engines to access information data, they cannot meet the individual needs of specific users in specific contexts. The personalized needs of a particular user in a particular context. Therefore, how to find useful and valuable information quickly has become one of the key issues in the development of big data. With the advent of the era of big data, recommendation systems, as an important technology to alleviate information overload, have been widely used in the field of e-commerce. Recommender systems suffer from a key problem: data sparsity. The sparsity of user history rating data causes insufficient training of collaborative filtering recommendation models, which leads to a significant decrease in the accuracy of recommendations. In fact, traditional recommendation systems tend to focus on scoring information and ignore the contextual context in which users interact. There are various contextual modal information in people's real life, which also plays an important role in the recommendation process. In this paper we achieve data degradation and feature extraction, solving the problem of sparse data in the recommendation process. An interaction context-aware sub-model is constructed based on a tensor decomposition model with interaction context information to model the specific influence of interaction context in the recommendation process. Then an attribute context-aware sub-model is constructed based on the matrix decomposition model and using attribute context information to model the influence of user attribute contexts and item attribute contexts on recommendations. In the process of building the model, the method not only utilizes the explicit feedback rating information of users in the original dataset, but also utilizes the interaction context and attribute context information of the implicit feedback and the unlabeled rating data. We evaluate our model by extensive experiments. The results illustrate the effectiveness of our recommender model.

Facial expression recognition is crucial for understanding human emotions and nonverbal communication. With the growing prevalence of facial recognition technology and its various applications, accurate and efficient facial expression recognition has become a significant research area. However, most previous methods have focused on designing unique deep-learning architectures while overlooking the loss function. This study presents a new loss function that allows simultaneous consideration of inter- and intra-class variations to be applied to CNN architecture for facial expression recognition. More concretely, this loss function reduces the intra-class variations by minimizing the distances between the deep features and their corresponding class centers. It also increases the inter-class variations by maximizing the distances between deep features and their non-corresponding class centers, and the distances between different class centers. Numerical results from several benchmark facial expression databases, such as Cohn-Kanade Plus, Oulu-Casia, MMI, and FER2013, are provided to prove the capability of the proposed loss function compared with existing ones.

The very first infected novel coronavirus case (COVID-19) was found in Hubei, China in Dec. 2019. The COVID-19 pandemic has spread over 215 countries and areas in the world, and has significantly affected every aspect of our daily lives. At the time of writing this article, the numbers of infected cases and deaths still increase significantly and have no sign of a well-controlled situation, e.g., as of 14 April 2020, a cumulative total of 1,853,265 (118,854) infected (dead) COVID-19 cases were reported in the world. Motivated by recent advances and applications of artificial intelligence (AI) and big data in various areas, this paper aims at emphasizing their importance in responding to the COVID-19 outbreak and preventing the severe effects of the COVID-19 pandemic. We firstly present an overview of AI and big data, then identify their applications in fighting against COVID-19, next highlight challenges and issues associated with state-of-the-art solutions, and finally come up with recommendations for the communications to effectively control the COVID-19 situation. It is expected that this paper provides researchers and communities with new insights into the ways AI and big data improve the COVID-19 situation, and drives further studies in stopping the COVID-19 outbreak.

Polysaccharides from marine algae exhibit beneficial biological activities. In this study, we examined the effect of polysaccharides from Codium fragile (PCF) on prebiotic and anti-obesity activity. PCF increases the growth of specific beneficial microbial populations with concomitant decrease in pathogenic microbes. Further, total phenolic content (TPC), total flavonoid content (TFC), and DPPH radical scavenging activity (DPPH activity) after fermentation with PCF as carbon source were higher than for the glucose as control. Moreover, PCF inhibited adipocyte differentiation by inducing differentiation-related factors when the induction of 3T3-L1 preadipocytes into adipocytes was induced. Therefore, we suggest that PCF can be used as prebiotic material with anti-obesity for human health.

Deep learning has been introduced to single-image super-resolution (SISR) in the last decade. These techniques have taken over the benchmarks of SISR tasks. Nevertheless, most architectural designs necessitate substantial computational resources, leading to a prolonged inference time on embedded systems or rendering them infeasible for deployment. This paper presents a comprehensive survey of plausible solutions and optimization methods to address this problem. Then, we propose a pipeline that aggregates the latter in order to enhance the inference time without significantly compromising the perceptual quality. We investigate the effectiveness of the proposed method on a lightweight GAN-based perceptual-oriented model as a case study. The experimental results show that our proposed method leads to significant improvement in the inference time on both Desktop and Jetson Xavier NX, especially for higher resolution input sizes on the latter, thereby making it deployable in practice.

In industry 4.0 era, video applications such as surveillance visual systems, video conferencing, or video broadcasting have been playing a vital role. In these applications, for manipulating and tracking objects in decoded video, the quality of decoded video should be consistent because it largely affects to the performance of the machine analysis. To cope with this problem, we propose a novel perceptual video coding (PVC) solution in which a full reference quality metric named Video Multimethod Assessment Fusion (VMAF) is employed together with a deep convolutional neural network (CNN) to obtain the consistent quality while still achieving the high compression performance. First of all, to achieve the consistent quality requirement, we propose a CNN model with an expected VMAF as input to adaptively adjust the quantization parameters (QP) for each coding block. Afterwards, to increase the compression performance, a Lagrange coefficient of Rate-Distortion optimization (RDO) mechanism is adaptively computed under Rate-QP and Quality-QP models. Experimental results show that the proposed PVC has achieved two targets simultaneously: the quality of video sequence is kept consistently with an expected quality level and the bit rate saving of the proposed method is higher than traditional video coding standards and relevant benchmark, notably with around 10% bitrate saving in average.

Non-timber forest products (NTFP) have contributed in various ways to the living, livelihoods, and trading of households and communities who live in rural and urban areas all over the world. This paper analyses the value chain of Jiaogulan (Gynostemma pentaphyllum) in the Cao Bang Geopark, Vietnam. 106 actors were surveyed using a semi-structured questionnaire: experts (agricultural extension officers, farmers' associations), harvesters, traders, primary processors, processors, distributors, and consumers. The results show that a map of Jiaogulan value chain, value added of households in main market channels, and impact of value added and distribution of Jiaogulan products on household income.

This paper discusses the computer-aided (CAD) classification between Hepatocellular Carcinoma (HCC), i.e., the most common type of liver cancer, and Liver Abscess, based on ultrasound image texture features and Support Vector Machine (SVM) classifier. Among 79 cases of liver diseases, with 44 cases of HCC and 35 cases of liver abscess, this research extracts 96 features of Gray-Level Co-occurrence Matrix (GLCM) and Gray-Level Run-Length Matrix (GLRLM) from the region of interests (ROIs) in ultrasound images. Three feature selection models, i) Sequential Forward Selection, ii) Sequential Backward Selection, and iii) F-score, are adopted to determine the identification of these liver diseases. Finally, the developed system can classify HCC and liver abscess by SVM with the accuracy of 88.875%. The proposed methods can provide diagnostic assistance while distinguishing two kinds of liver diseases by using a CAD system.

PM2.5 and PM>2.5 were separately collected in Kanazawa, Japan in every season from the spring of 2017 to the winter of 2018, and nine polycyclic aromatic hydrocarbons (PAHs) and six nitropolycyclic aromatic hydrocarbons (NPAHs) were determined by HPLC with fluorescence and chemiluminescence detections, respectively. Atmospheric concentrations of both PAHs and NPAHs showed seasonal changes (highest in the winter and lowest in the summer), which were different from the variations of TSP and PM2.5 (highest in the spring). Contributions of major sources to combustion-derived particulate (Pc) in PM2.5 were calculated by the NP-method using pyrene and 1-nitropyrene as representative markers of PAHs and NPAHs, respectively. The annual average concentration of Pc accounted for only 2.1% of PM2.5, but showed the same seasonal variation as PAHs. The sources of Pc were automobiles (31%) and coal heating facilities/industries (69%). The source of Pyr was almost entirely coal heating facilities/industries (98%). A backward trajectory analysis showed that automobile-derived Pc was mainly from Kanazawa and its surroundings and that coal heating facilities-derived Pc was transported from city areas in central and northern China in the winter and during the Asian dust event in the spring. These results show that large amounts of PAHs were long-range transported from China in the winter. Even in spring when the coal heating season was over in China, PAHs came over to Japan after Asian dust storms passed through Chinese city areas. The main contributor of NPAHs was automobiles in Kanazawa and its surroundings. The recent Pc concentrations were much lower than those in 1999. This decrease was mostly attributed to the decrease in the contribution of automobiles. Thus, changes of atmospheric concentrations of Pc, PAHs and NPAHs in Kanazawa were strongly affected not only by the local emissions but also long-range transport from China.

During the Covid-19 pandemic in Taiwan, analytical tools of PEST (political, economic, social-cultural, and technological), SWOT (strength, weakness, opportunity, threat), nine building blocks of a business model canvas, and knowledge management were combined to develop a theoretical framework, and used to assess business, smart and sustainable management of two case companies: Tung Sheng Company Limited and its subsidiary, Strong Basic Enterprise Limited. A heuristic inquiry research design was adopted. In addition to secondary data from the two case companies, major top managers were interviewed to reveal constructive questions about the existing business models and to re-interpret strategy. The results showed that case companies own capabilities of R &amp; D (research and development) as a foundation to further apply new smart ICT (information and communication technology) and execute green manufacturing. Additionally, strong key partnerships are used to diversify business investment for leveraging on limited resources given current insufficient qualified employees. Resilient practices adopted new and green technology to help mitigate the negative impacts of the Covid-19 pandemic. This study provides a useful framework and practical information about how to examine business models, smart and sustainable management processes of the two case companies and to make adjustments in strategies for the future.

We report the effects of surface passivation by depositing a hydrogenated amorphous silicon (a-Si:H) layer on the electrical characteristics of low temperature polycrystalline silicon thin film transistors (LTPS TFTs). The a-Si:H layer was optimized by hydrogen dilution and its structural and electrical characteristics were investigated. The a-Si:H layer in the transition region between a-Si:H and µc-Si:H resulted in superior device characteristics. Using an a-Si:H passivation layer, the field-effect mobility of the LTPS TFT was increased by 78.4% compared with a conventional LTPS TFT. Moreover, the leakage current measured at a V_GS of 5 V was suppressed because the defect sites at the poly-Si grain boundaries were well passivated. Our passivation layer, which allows thorough control of the crystallinity and passivation-quality, should be considered a candidate for high performance LTPS TFTs.

Betadine (Providone-Iodine) solution is a topically applied antiseptic, which has been used for wound care and surgery for decades for the prevention and treatment of skin and wound infections. However, several studies have documented the ineffectiveness of Betadine solution. Other topical antimicrobial dressings, including those that contain silver, have been used in the management of infected wounds. The present study was undertaken to determine if the combination of 5% Betadine solutions and silver colloidal gel (Ag-gel), is more effective than the individual materials in inhibiting the growth of both Gram negative and Gram positive bacteria. These determinations were carried out by both the colony forming unit (CFU) assay, and confocal laser scanning microscopy (CLSM). Ag-gel showed complete inhibition on all the bacteria, except Klebsiella pneumoniae CI strain while 5% Betadine concentrations did not completely kill any of the tested bacteria. However, K. pneumoniae was completely eliminated in the presence of the combination of 5% Betadine solution plus Ag-gel. Confocal laser microscopy confirmed the CFU results. Thus this study demonstrated that while the individual treatments are not effective in killing all the bacteria tested, the combination of 5% Betadine solution and Ag-gel completely kill all bacteria tested, including K. penumoniae CI.

In this paper, we propose a method for assessing the effectiveness of entropy features using several chaotic mappings. We anlyze fuzzy entropy (FuzzyEn) and neural network entropy (NNetEn) on four discrete mappings: the logistic map, the sine map, the Planck map, and the two-memristor-based map, with a base length time series of 300 elements. FuzzyEn is shown to have improved global efficiency (GEFMCC) in the classification task compared to NNetEn. At the same time, there are local areas of the time series dynamics in which the classification efficiency NNetEn is higher than FuzzyEn. The results of using horizontal visibility graphs (HVG) instead of the raw time series are also shown. GEFMCC decreases after HVG time series transformation, but there are local areas of the time series dynamics in which the classification efficiency increases after including the HVG. The scientific community can use the results to explore the efficiency of entropy-based classification of time series.

Intra-articular fractures are a major cause of post-traumatic osteoarthritis (PTOA). Despite adequate surgical treatment, the long-term risk for PTOA is high. Previous studies reported that joint injuries initiate an inflammatory cascade characterized by elevation of synovial pro-inflammatory cytokines, which can lead to cartilage degradation and PTOA development. This review summarizes the literature on the post-injury regulation of pro-inflammatory cytokines and the markers of cartilage destruction in patients suffering from intra-articular fractures. METHODS We searched Medline, Embase, and Cochrane databases (1960–February 2020) and included studies that were performed on human participants and included control groups. Two investigators assessed the quality of the included studies using Covidence and the Newcastle-Ottawa Scale. RESULTS Based on the surveyed literature, several synovial pro-inflammatory cytokines, including interleukin (IL)-1β, IL-2, IL-6, IL-8, IL-12p70, interferon-y, and tumor necrosis factor-α, were significantly elevated in patients suffering from intra-articular fractures compared to control. A simultaneous elevation of anti-inflammatory cytokines such as IL-10 and IL-1RA was also observed. In contrast, IL-13, CTX-II, and aggrecan concentrations did not differ significantly between the compared cohorts. CONCLUSIONS Overall, intra-articular fractures are associated with an increase in inflammation-related synovial cytokines. However, more standardized studies which focus on the ratio of pro- and anti-inflammatory cytokines at different time points are needed.

Chromophobe renal cell carcinoma (chRCC) and oncocytoma (RO) are renal tumor types originating from alpha intercalated cells of the collecting ducts of the kidney. Both tumor types have similar gross histological morphology and increased mitochondria, which leads to difficulties differentiating between these tumors, especially with core biopsy samples. This study aims to apply a machine learning approach to develop a molecular classifier based on transcriptomics data. Here we generated a meta-data set containing 62 chRCC and 45 RO gene expression arrays. Arrays were subjected to quality control steps, and genes were selected based on differential expression and ROC analysis. The final gene list was evaluated with UMAP based dimension reduction followed by density-based clustering with 95.5% accuracy. Molecular profiling by KEGG pathway analysis identified enrichment of fatty acid oxidation pathway in RO. We finally identified and validated the 30-gene signature, with an accuracy of 94.4% to distinguish chRCC from RO on UMAP analysis. Our results show that chRCC and RO have a distinct gene signature that can differentiate these tumors and complement histology for routine diagnosis of these two tumors.

Edge computing has emerged as a significant computing trend alongside the rapid expansion of the Internet of Things (IoT). Computing operations at the network’s edge offer a solution to the high latency and service overload challenges often associated with cloud computing. Additionally, the Secure Hash Algorithm-3 (SHA-3) plays a crucial role in ensuring data integrity and is implemented for numerous applications in the IoT field. Therefore, integrating the SHA-3 accelerator into edge computing is essential. Moreover, recent studies about SHA-3 have primarily focused on achieving high performance and optimizing resource utilization for SHA-3. However, these studies have overlooked the crucial aspect of data transfer between the external memory and the hash function block, as transfer time plays a significant role. This paper proposes an efficient SHA-3 architecture designed for System-on-Chip (SoC) Field Programmable Gate Array (FPGA) to address the aforementioned challenges and be suitable for real edge computing. The architecture contains three key techniques. First, the harmony of padding and Direct Memory Access (DMA) for managing the data transfer process and enhancing performance efficiency based on Serial Input to Parallel Output (SIPO) and a barrel shifter. Secondly, implementing internal pipelining within the Round Function (RF) to reduce critical path delays and optimize resource utilization. Finally, designing four modes (SHA3-224, SHA3-256, SHA3-384, and SHA3-512) to cater to various applications. Our architecture is implemented and tested on the DE10-Standard Development Kit (Cyclone V SX SoC-5CSXFC6D6F31C6N), which is integrated into the FPGA and is controlled by a Dual-Core ARM Cortex-A9 processor. The result is up to 38.34 Gbps in throughput and 5.61 Mbps/ALM in efficiency for the RF computation, 28.02 Gbps in throughput, and 3.63 Mbps/ALM for the full proposed architecture.

Abstract. This paper proposes a Second Order Terminal Sliding Mode (2TSM) approach to the trajectory tracking of Differential Drive Mobile Robot (DDMR). Within this cascaded control scheme, the 2TSM dynamic controller, at the inner most loop, tracks the robot’s velocity quantities; while a kinematic controller, at the outer most loop, regulates the robot’s positions. In this manner, chattering is greatly attenuated and finite time convergence is guaranteed by the second order TSM manifold which involves higher order derivatives of the state variables, resulting in inherently robust as well as fast and better tracking precision. The simulation results demonstrate the merit of the proposed control methods.

Recent prolonged dry periods and lack of irrigation water have severely affected the productivity of coffee farms’ in the Central Highlands of Vietnam. This paper analyzes the efficiency of irrigation water use for Robusta coffee (Coffea canephora) in Lam Dong province, Highlands, Vietnam. A Cobb-Douglas production function was used to determine coffee productivity’s response to the application of irrigation water and other production factors using data collected from 194 farmers while the Technical Efficiency (TE) and Irrigation Water Use Efficiency (IWUE) were analyzed using a Data Envelopment Analysis (DEA) model. The correlation of different factors to IWUE was determined using the Tobit model. The production function analysis using Cobb-Douglas shows that the volume of irrigation water, amount of working capital, labor and farm size significantly influence coffee productivity. It also shows that indigenous farmers are more efficient in utilizing irrigation water than the (mostly Kinh) migrant farmers. The Tobit result, on the other hand. indicates that farmers’ experience, education level, distance of farm to water source, security of access to water source, extension contact and credit access significantly affect IWUE. The study findings further suggest that mitigating water shortages in coffee farms require sub-regional and national policy support such as better access to credit and extension services, training, land management and household-level effort to improve farming practices, through the application of appropriate technologies and traditional knowledge.

Ixodes scapularis is the major vector of Lyme disease in the eastern United States. Each active life stage (larva, nymph, and adult) takes a blood meal either for developing and molting to the next stage (larvae and nymphs) or for oviposition (adult females). This protein-rich blood meal is the only food taken by Ixodes ticks and therefore blood digestion is very important for tick survival. Most studies on blood digestion in ticks have shown that the initial stages of digestion are carried out by cathepsin proteases within acidic digestive cells. However, most of these studies have focused on partially engorged ticks. In other hematophagous arthropods, the serine proteases play an important role in blood protein degradation. In this study, we determined transcript expression of four I. scapularis serine proteases with previously characterized roles in blood digestion. RNA interference was used for functional analysis and a trypsin-benzoyl-D, L-arginine 4-nitoanilide assay was used to measure active trypsin levels. An in vitro hemoglobinolytic assay was performed with or without serine protease inhibitor. Our data suggest that trypsin levels increase significantly after blood feeding and peaked in larvae, nymphs, and adults at 3, 1, and 1 day post host detachment, respectively. The knockdown of three previously identified serine proteases by RNAi negatively impacted blood intake, survival, fecundity, levels of active trypsin in the gut and resulted in lower hemoglobin degradation in vitro. A trypsin inhibitor, PMSF, blocked the action of trypsin in the gut extract resulting in 65% lower hemoglobin degradation. We provide evidence of the serine proteases as digestive enzymes in fully engorged, replete females. Our data also demonstrated that in addition to blood digestion, these serine proteases might have a role in blood feeding success in I. scapularis.

Catalase, an antioxidant enzyme widely produced in mammalian cells and bacteria, is crucial in mitigating oxidative stress in a hostile environment. This function enhances the intracellular survivability of various intracellular growth pathogens, including Brucella abortus. In this study, to determine whether the inhibition of catalase can inhibit the intracellular growth of Brucella (B.) abortus, we employed 3-amino-1,2,4-triazole (3-AT), a catalase inhibitor, in both RAW 264.7 macrophage cells and an ICR mouse model during Brucella infection. The intracellular growth assay indicated that 3-AT exerts growth-inhibitory effects on B. abortus within macrophages. Aside from that, it contributes to the accumulation of reactive oxygen species and the formation of nitric oxide. Notably, 3-AT diminishes the activation of the nucleus transcription factor (NF-κB) and modulates cytokine secretion within infected cells. In our mouse model, the administration of 3-AT reduced B. abortus proliferation within the spleen and liver of infected mice. This reduction was accompanied by a diminished immune response to infection, as indicated by lowered levels of TNF-α, IL-6, IL-10, and altered CD4+/CD8+ T-cell ratio. These results suggest the protective and immunomodulatory effects of 3-AT treatment against Brucella infection.

Machine learning applications often need large amounts of training data to perform well. Whereas unlabeled data can be easily gathered, the labeling process is difficult, time-consuming, or expensive in most applications. Active learning can help solve this problem by querying labels for those data points that will improve the performance the most. Thereby, the goal is that the learning algorithm performs sufficiently well with fewer labels. We provide a library called scikit-activeml that covers the most relevant query strategies and implements tools to work with partially labeled data. It is programmed in Python and builds on top of scikit-learn.

Mushrooms have long rich history in folk medicine, traditional and functional foods due to high content of dietary myco-nutrients. Currently, there is increased interest in finding appropriate food-grade green ex-traction systems capable of extracting these bioactive compounds from dietary mushrooms for applica-tions in various food, pharmacological or nutraceutical formulations. Herein, we evaluated a modified Swiss water process (SWP) method using alkaline and acidic pH at low and high temperature under pressurized conditions as a suitable green food grade solvent to obtained extracts enriched with my-co-nutrients (dietary phenolics, total antioxidants (TAA), vitamins, and minerals) from Chaga. Ultra-high performance liquid chromatography coupled to high resolution accurate mass tandem mass spectrometry (UHPLC-HRAMS-MS/MS) was used to assess the phenolic compounds and vitamin levels in the extracts, while inductively coupled plasma mass spectrometry (ICP-MS) was used to determine the mineral con-tents. Over twenty phenolic compounds were quantitatively evaluated in the extracts and the highest total phenolic content and antioxidant activity was observed at pH11.5 at 100°C. The most abundant phenolic compounds present in Chaga extracts included phenolic acids such as protocatechuic acid 4-glucoside (0.7-1.08µg/mL), syringic acid (0.62-1.18µg/mL), and myricetin (0.68-1.3µg/mL). Vitamins are being reported for the first time in Chaga. pH 2.5 at 100°C treatment shows superior effects in extracting the B vitamins whereas pH 2.5 at 60 and 100°C treatments were outstanding for extraction of total fat-soluble vitamins. Vitamin E content was the highest for the fat-soluble vitamins in the Chaga extract under acidic pH (2.5) and high temp. (100°C) and ranges between 50 to 175 µg/100g Chaga. Antioxidant minerals ranged from 85.94 µg/g (pH7 at 100°C) to 113.86 µg/g DW (pH2.5 at 100°C). High temperature 100°C and a pH of 2.5 or 9.5. The treatment of pH11.5 at 100°C was the most useful for recovering phenolics and antioxidants from Chaga including several phenolic compounds reported for the first time in Chaga. SWP is being proposed herein for the first time as a novel, green food-grade solvent system for the extraction of myco-nutrients from Chaga and have potential applications as a suitable approach to extract nutrients from other matrices. Chaga extracts enriched with bioactive myconutrients and antioxidants may be suitable for further use or applications in the food and nutraceutical industries.

Agricultural land fires have been linked to various and adverse impacts on ecosystems, food security and the agriculture sector. Understanding the patterns and drivers of agricultural land fires is essential for effective agricultural land fire management. The key objectives of this study were to (1) analyze the temporal and spatial patterns of agricultural land fires using satellite remote sensed data, (2) assess a range of environmental conditions that could drive the occurrence of agricultural land fires, (3) determine the best model for predicting agricultural land fires and (4) determine the relative contribution of each environmental condition variable on the best predictive model. We used both univariate and multivariate regressions for the fire prediction capability of four independent environmental conditions (fuel, weather, topographic and anthropogenic). Analysis of historical satellite data revealed that agricultural land fires were more frequent than forested land fires. Our analyses also revealed that fuel condition was the most important variable for predicting agricultural land fires followed by weather, topographic and anthropogenic conditions. This study provides a novel multivariate model for predicting agricultural land fires that harbors the potential to improve agricultural land fire management and reduce fire risk within the agricultural sector.

Background: The robustness of sero-surveillence has delineated the high burden of SARS-CoV-2 infection in children; however, these existing data showed wide variation. This study aimed to identify the serostatus of antibodies against SARS-CoV-2 and associated factors among children following the fourth pandemic wave in Vietnam. Methods: A cross-sectional study was conducted at Vietnam National Children’s Hospital (VNCH) between March 13 and April 3, 2022. 4,032 eligible children seeking medical care for any medical condition not related to acute Covid-19 infections was tested for IgG SARS-CoV-2 Antibodies by ADVIA Centaur® SARS-CoV-2 IgG (sCOVG) assay using the residuals of routine blood samples. Results: The median age of enrolled children was 39 (IQR=14-82) months. The overall seropositive prevalence was 59.2%, and the median antibody titer was 4.78 [IQR 2.38-9.57] UI/mL. The risk of seropositivity and the median antibody titer was not related to gender (58.6% versus 60.1%, 4.9 versus 4.6 UI/mL, all p&gt;0.05). Among age groups, the highest seroprevalence was reported in the children aged 13 to &lt;36 months old. Children aged ≤12 months were likely to be seropositive compared to children aged 36 to &lt;60 months (59.2% versus 57.5%, p=0.49) and those aged ≥144 months (59.2% versus 65.5%, p=0.16). Children aged ≥144 months exhibited a significantly higher titer of protective COVID-19 antibodies than other age groups (p &lt;0.001). In multivariate logistic regression, we observed independent factors associated with SARS-CoV-2 seropositivity, including the age 13 to &lt;36 months (OR=1.29, 95%CI=1.06-1.56, p=0.01), 60 to &lt;144 months (OR=79, 95%CI=0.67-0.95, p=0.01), ≥144 months (OR=1.84, 95%CI=1.21-2.8, p=0.005), the presence of infected household members (OR=2.36, 95%CI=2.06–2.70, p&lt;0.001), participants from Hanoi (OR=1.54, 95%CI=1.34-1.77, p&lt;0.001), underlying conditions (OR=0.71, 95%CI=0.60-0.85, p&lt;=0.001), and using corticosteroids or immunosuppressants (OR=0.64, 95%CI=0.48-0.86, p=0.003). Conclusions: This study highlights a high seroprevalence of antibodies against SARS-CoV-2 among children seeking medical care for non-COVID-19-related conditions in a tertiary children’s hospital in Hanoi, Vietnam. In the context of reopening in-person schools and future emerged COVID-19 variants, this point will also be a key message about the necessity of “rush-out” immunization coverage for children, especially those under the age of three years.

Knee osteoarthritis is the most popular type of osteoarthritis that causes extreme pain in elderly. Currently there is no cure for osteoarthritis. To lessen clinical symptoms, glucosamine was suggested. The primary goal of our study is to evaluate the efficacy and safety of glucosamine from recent studies. Electronic databases such as PubMed, Scopus, Cochrane were used to assess RCT. From the beginning through March 2023, the papers were checked, and if they fulfilled the inclusion criteria, they were then examined. WOMAC and VAS scales were considered as main outcome measure. A total of 15 studies were selected. Global pain was significantly decreased in comparison to placebo, as measured by the VAS index, with an overall effect size SMD of -7.41 ([95% CI] 14.31, 0.51). The WOMAC scale confirmed that pain, stiffness, and physical function had improved, however the effects were insufficient. A statistical update also revealed that there were no reports of serious medication interactions or significant adverse events. To summarize, glucosamine is more effective than a placebo at reducing pain in knee osteoarthritis patients. In long-term treatment, oral glucosamine sulfate 1500 mg/day is believed to be well tolerated.

Rice prolamins are categorized into three groups by molecular size (10, 13, or 16 kDa), while the 13 kDa prolamins are assigned to four subgroups (Pro13a-I, Pro13a-II, Pro13b-I, and Pro13b-II) based on cysteine residue content. Here, we generated four knockout strains of rice using CRISPR-Cas9, each of which demonstrated selectively reduced expression of specific subgroups of the 13 kDa prolamins. These four mutant rice lines also demonstrated compensatory expression of glutelins and non-targeted prolamins, which resulted in low grain weight, altered starch content and atypically-shaped starch granules and protein bodies. Transcriptome analysis identified 746 transcripts that were differentially expressed in the mutant rice lines during development. These transcripts played roles primarily in RNA processing, protein synthesis, stress response, and transport. After selective suppression/knockout of genes in the Pro13a-I subgroup, compensatory upregulation of genes in the Pro13a-II and Pro13b-I/II subgroups was observed. Compensatory expression of 9 ER stress and 17 transcription factor genes was also observed in mutant rice in which expression of 13 kDa prolamin genes was suppressed. Our results provide valuable insight into the regulatory mechanisms underlying rice seed development and the specific roles played by 13 kDa rice prolamins and their target genes.

The coastline in the Ca Mau and the Kien Giang provinces of the Vietnamese Mekong Delta has been severely eroded in recent decades. Pile-Rock Breakwaters (PRBW) are one of the most widely adopted structures for controlling shoreline erosion in this region. These structures are effective for wave energy dissipation, stimulating sediment accumulation, and facilitating the restoration of mangrove forests. These breakwaters are generally considered to be best-engineering practice however there is currently insufficient scientific evidence with regard to specific structural design aspects. This can lead to PRBW structures being compromised when deployed in the field. This study uses a physical model of a PRBW in a laboratory to investigate several design parameters, including crest width and working states (i.e. submerged, transition, and emerged), and investigates their relationship with the wave transmission coefficient, wave reflection coefficient, and wave energy dissipation. To investigate these relationships further, empirical formulas were derived for PRBWs under different sea states and crest widths to aid the design process. The results showed that PRBW width had a significant influence on the wave energy coefficients. The findings revealed that the crest width of the breakwater is inversely proportional to the wave transmission coefficient (K_t) under the emerged state. The crest width is also proportional to the wave reduction efficiency and wave energy dissipation in both working states (i.e., submerged and emerged states). The front wave disturbance coefficient (K_f) was found to be proportional to the wave reflection coefficient, and the wave height in front of the structure was found to increase by up to 1.4 times in the emerged state. The wave reflection coefficient requires special consideration to reduce the toe erosion in the structure. Lastly, empirical equations including linear and non-linear formulas were compared with previous studies for different classes of breakwaters. These empirical equations will be useful for understanding the wave transmission efficiency of PRBWs. The findings of this study provide important guidance for PRBW design in the coastal area of the Mekong Delta.

Layered halide perovskites have emerged as a promising contender in solid-state lighting thanks to their tunable bandgap, high luminescence quantum yield, and high color purity. However, the fabrication of perovskite light-emitting devices in laboratories usually experiences low de-vice-to-device reproducibility since perovskite crystallization is highly sensitive to ambient condi-tions, such as humidity and temperature. Although device processing inside gloveboxes is primarily used to reduce the influence of oxygen and moisture, several extraneous variables, including gas-eous pollution traces and thermal fluctuations in the inert atmosphere or contaminations from re-sidual solvents confined in the enclosed environment, can destabilize the crystallization process and alter the properties of the emissive layers. Here, we examine different experimental set-ups for spin-coating deposition of layered perovskites in inert atmospheres and their influences on the formation of polycrystalline thin films. Our results demonstrate that fluctuations in the glovebox properties (concentrations of residual O2 and H2O or solvent traces), even in very short timescales, can negatively impact the consistency of the perovskite film formation, while thermal variation plays a relatively minor role in this phenomenon. Furthermore, careful storage of chemical species inside the workstation is critical for reproducing high-quality perovskite layers. Consequently, when applying our most controlled environment for perovskite deposition, the photoluminescence life-time of perovskite thin films shows a standard deviation of only 3%, whereas the reference set-up yields a 15% standard deviation. Regarding complete perovskite light-emitting diodes, the uncer-tainties in statistical luminance and EQE data are significantly reduced from 230% and 140% to 38% and 42%, respectively.

Our primary objectives were a) to determine the need for, and the availability of point-of-care testing (POCT) for infectious diseases and b) to recommend point-of-care testing strategies and spatial care paths (SCPs) that enhance public health preparedness in regional districts of Thua Thien Hue Province (TTHP), Central Vietnam, where we conducted field surveys. Medical professionals in 7 community health centers (CHCs), 7 district hospitals (DHs) and 1 provincial hospital (PH) participated. Survey questions (English and Vietnamese) determined the status of diagnostic testing capabilities for infectious diseases and other acute medical challenges in TTHP. Infectious disease testing was limited: 6 of 7 CHCs (86%) lacked infectious disease tests. One CHC (14%, 1/7) had two forms of diagnostic tests available for the detection of Malaria. All CHCs lacked adequate microbiology laboratories. District hospitals had few diagnostic tests for infectious diseases (Tuberculosis, Syphilis), blood culture (29%, 2/7), and pathogen culture (57%, 4/7) available. The PH had broader diagnostic testing capabilities but lacked preparedness for highly infectious disease threats (e.g., Ebola, MERS-CoV, SARS, Zika, and Monkeypox). All sites reported having COVID-19 rapid antigen tests; COVID-19 RT-PCR tests were limited to higher tier hospitals. We conclude that infectious disease diagnostic testing should be improved and POC tests must be supplied near patients’ homes and in primary care settings for the early detection of infected individuals and mitigation of the spread of new COVID-19 variants and other highly infectious diseases.

Coronavirus disease-2019 (COVID-19) was seen as a respiratory disease, however, an increasing number of reports indicated that the spike protein could also be the cause of the long-term post-infectious conditions known as Long-COVID characterized by a group of unresponsive idiopathic severe neuro, cardio-vascular disorders, including strokes, cardiopathies, neuralgias, fibromyalgia, and Parkinson's like-disease. Different lines of pieces of evidence confirmed that the spike protein that can be found on the surface of the SARS-CoV-2 virus latches onto angiotensin-converting enzyme 2 (ACE2) receptors located on target cells. The RNA genome of coronaviruses, which, has a median length of 29 kb and is the longest among all RNA viruses, is comprised of six to ten open reading frames (ORFs) that are responsible for encoding both the replicase and structural proteins for the virus. Each of the components of the viral genome is packaged into a helical nucleocapsid that is surrounded by a lipid bilayer. The viral envelope of coronaviruses is typically made up of three proteins that include the membrane protein (M), the envelope protein (E), and the spike protein (S). The spike protein not only facilitates the virus entry into healthy cells, which is the first step in infection but also promote profound damage to different organs and tissues leading to severe impairments and long-term disabilities. Here, we discussed the pervasive mechanism that spikes mRNA adopted to alter multipotent and pluripotent stem cell (SCs) genomes and the acquired disability of generating an infinite number of affected clonal cells. This stance is based on the molecular and evolutionary aspects obtained from retrotransposons-retrotransposition in mammalians and humans that documented the frequent integration of mRNA molecules into genomes and thus into DNA. Retrotransposition is the molecular process in which transcribed and spliced mRNAs are accidentally reverse-transcribed and inserted into new genomic positions to form a retrogene. Sequence-specific traits of mRNA clearly showed long interspersed element-1 (LINE-1 or L1) to confirm the retrotransposition, considered the most abundant autonomously active retrotransposons in the human genome. In mammals, L1 retrotransposons drive retrotransposition and are composed of long terminal repeats (LTRs) and non-LTR retrotransposons (mainly long interspersed nuclear elements or LINEs); specifically, the LTR-mediated retrocopies are immediately cotranscribed with their flanking LTR retrotransposons. In response to retrotransposons transposition, stem cells (SCs) employ a number of silencing mechanisms, such as DNA methylation and histone modification. This manuscript theorizes the expression patterns, functions, and regulation of mRNA Spike protein imprinted by SCs retrotransposons which generate unlimited lines of affected cell progenies and tissues as the main condition of untreatable Spike-related inflammatory conditions.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.