This work is related to the environmental toxicology risk assessment and evaluation of possible transformation of carbon-based nanomaterials (CNMs) after the contact with marine microalgae. The materials used in the study represent common and widely applied multiwalled carbon nanotubes (CNTs), fullerene (C60), graphene (Gr), and graphene oxide (GrO). The toxicity was evaluated as growth rate inhibition, esterase activity, membrane potential, and reactive oxygen species generation changes. The measurement was performed with flow cytometry after 3, 24, 96 h, and 7 days. Biotransformation of nanomaterials were evaluated after 7 days of microalgae cultivation with CNMs by FTIR and Raman spectroscopy. The calculated toxic level (EC50 in mg/L, 96 h) of ued CNMs reduced in the following order: CNTs (18.98) > GrO (76.77) > Gr (159.40) > C60 (414.0). Oxidative stress and membrane depolarization was the main toxic action of CNTs and GrO. At the same time, Gr and C60 decreased the toxic action with time and had no negative impact on microalgae even at concentration of 125 mg/L. Moreover, C60 and Gr after seven days of the contact with microalgae cells obtained structural deformations.

The growing production and application of carbon-based nanomaterials (CNMs) represent possible risks for aquatic systems. However, the variety of CNMs with different physical and chemical properties, and different morphology complicated the understanding of their potential toxicity. This paper aims to evaluate and compare the toxic impact of four most common CNMs, namely multiwalled carbon nanotubes (CNTs), fullerene (C60), graphene (Gr), and graphene oxide (GrO) in marine microalgae Porphyridium purpureum. The microalgae cells were exposed to the CNMs for 96 h and measured by flow cytometry. Based on the obtained results, we determined no observed effect level (NOEL), calculated EC10 and EC50 concentrations for growth rate inhibition, esterase activity, membrane potential, and reactive oxygen species (ROS) generation changes for each tested CNMs. According to the sensitivity (growth rate inhibition) of P. purpureum, the used CNMs can be listed in following order: CNTs > GrO > Gr > C60. The toxicity of CNTs was significantly higher than the toxic effect of the other used CNMs and only this sample caused increase of ROS generation in microalgae cells. This effect caused by trace metal residuals in CNTs and high affinity between particles and microalgae associated with the presence of exopolysaccharide coverage on P. purpureum cells.

The structure of wound dressing materials presents one of the most relevant characteristics for effective skin tissue repair. Electrospinning is a common technique used to produce polymeric fibres that can mimic fibrillar disposition of skin extracellular matrix, favouring cell migration, and thus regeneration of the damaged tissue. Moreover, beads, also known as by-products of electrospinning, have potential as reservoirs for sustained drug release. Processing parameters, such as molecular weight and viscosity of the polymer solution, can affect the desirable morphologies of electrospun films. Thereby, this work had the purpose of producing and characterized electrospun polycaprolactone (PCL) mats loaded with propolis, a popular extract in traditional medicine with potential for skin repair aid. Films with different morphologies were obtained depending on the storage period of the solution prior to the lectrospinning, probably due to the PCL hydrolysis. FTIR analyses of the extract confirmed propolis composition. GPC and viscosity analyses demonstrated that the decrease in molar mass over the storage period was responsible for nanostructure diversity. Propolis acts as a lubricant agent, affecting the spun solutions' viscosity and the thermal properties and hydrophilicity of the films. All films are within the value range of the water vapour transpiration rate of the commercial products. The presence of beads did not affect the propolis release pattern. However, "in vitro" wound healing assay showed that propolis-loaded films composed by beaded fibres increased the cell migration process. Thus, it can be inferred that these films presented the potential for wound dressing application.

The present work analyzes the behavior in terms of corrosion resistance of three reinforced concrete formulations over a period of 1 year. The samples were accompanied by creating a monitoring methodology using the Electrochemical Impedance Spectroscopy (EIE) technique, working only with the real component over time. Three mixtures were used, one conventional without pozzolanic addition (REF) and two others with pozzolanic additions, rice husk ash (RCA) and metakaolin (MK). Prototypes were created and exposed to the action of a 165g/l NaCl sodium chloride solution. The characterization of the materials was carried out by determining the chloride diffusion profile (ASTM 1556), analyzing images using tomography and with the support of analytical techniques such as x-ray fluorescence and x-ray diffraction. The monitoring methodology using the EIE demonstrated the positive effect of the insertion of pozzolans, rice husk ash (RCA) and metakaolin (MK), by delaying the process of chloride diffusion in the concrete, resulting in greater resistance to corrosion. The EIE also showed that the active mineral addition in concrete, of aluminum-silicic composition (MK), had a predominant protective effect on the steel//concrete interface against the attack of chloride ions.

Cryptococcus neoformans is a human multidrug-resistant yeast with high mortality rates in immunocompromised patients. Recently, the synthetic peptide Mo-CBP3-PepII emerged as a potent anticryptococcal molecule with an MIC50 at low concentration. Here, the mechanisms of action of Mo-CBP3-PepII were deeply analyzed to provide new information about how it led C. neoformans cells to death. Light and fluorescence microscopies, analysis of enzymatic activities, and proteomic analysis were employed to understand the effect of Mo-CBP3-PepII on C. neoformans cells. Light and fluorescence microscopies revealed Mo-CBP3-PepII induced the accumulation of anion superoxide and hydrogen peroxide in C. neoformans cells. In addition to a reduction in the activity of superoxide dismutase (SOD), ascorbate peroxidase (APX), and catalase (CAT) in the cells treated with Mo-CBP3-PepII. In the presence of Ascorbic acid (AsA), no ROS were detected and Mo-CBP3-PepII lost the inhibitory activity against C. neoformans. Yet, Mo-CBP3-PepII inhibited the activity of lactate dehydrogenase (LDH), ergosterol biosynthesis, and induced the decoupling of cytochrome c from the mitochondrial membrane. Proteomic analysis revealed a reduction in the abundance of proteins related to energetic metabolism, DNA and RNA metabolism, pathogenicity, protein metabolism, cytoskeleton, and cell wall organization and division. Our findings indicated that Mo-CBP3-PepII might have multiple mechanisms of action against C. neoformans cells, mitigating the development of resistance and thus being a potent molecule to be employed in the production of new drugs against C. neoformans infections.

Cryptococcus neoformans threaten the health, causing cryptococcal meningitis and pneumonia, especially in immunosuppressed patients, which can be fatal. Recently, our research group evaluated and studied the mechanisms of action of four synthetic peptides (SP) against C. neoformans. Here, in silico and in vitro analyses help deepen understanding of peptides' mechanisms of action. The interaction of the peptides with a membrane receptor was analyzed by docking analysis, in addition to ROS overproduction and the modulation of redox metabolism, inhibition of ergosterol biosynthesis, and release of cytochrome c. Out of four, three peptides interacted with membrane receptor PHO36 altering its structure and function and leading to a higher accumulation of O₂- and H2O2. C. neoformans cells treated with SP presented a reduction in the activity of antioxidant enzymes, corroborating ROS accumulation. However, in the presence of the antioxidant ascorbic acid, some peptides could not induce this oxidative stress and have the activity against C. neoformans affected. Curiously, two of these SPs still maintained the activity against C. neoformans and even induced the membrane pore formation as revealed by propidium iodide uptake assay, revealing their mechanism of action is ROS-independent. Additionally, SPs inhibited the biosynthesis of ergosterol, which corroborates the pore formation on the membrane of C. neoformans cells, inhibited the lactate dehydrogenase activity affecting the cell metabolism, and induced the release of Cyt c from the mitochondria inducing death by apoptosis in the cryptococcal cells. Our findings strongly suggest that SPs act by multiple mechanisms, making it difficult for C. neoformans to acquire resistance highlighting the potential of SPs as alternative molecules in treating infections caused by C. neoformans.

Carbonate reservoirs, influenced by depositional and diagenetic processes and characterized by features like faults and vugs that impact storage capacity, require more than traditional Borehole Imaging logs (BHI) for accurate porosity data. This data is essential for geological assessments, production forecasting, and reservoir simulations. This work aims to address this limitation by developing methods to measure and monitor the sustainability of carbonate reservoirs and exploring the application of sustainability principles to their management. The study integrates BHI and conventional logs from two wells to classify porosity-based facies within the Barra Velha Formation (BVF) in the Santos Basin. The methodology involves four steps: (i) analyzing conventional logs; (ii) segmenting BHI logs; (iii) integrating conventional and segmented BHI logs using Self-Organizing Maps (SOM); and (iv) interpreting the resulting classes. Matrix porosity values and non-matrix pore sizes categorize the porosity into four facies (A to D). Facies A has high non-matrix porosity with 14,560 small megapores, 5,419 large megapores, and 271 gigapores (71.9%, 26.76%, and 1.34% of the 20,250 pores, respectively). Facies B shows moderate non-matrix porosity with 8,669 small megapores, 2,642 large megapores, and 33 gigapores (76.42%, 23.29%, and 0.29% of the 11,344 pores, respectively) and medium matrix porosity. Facies C exhibits low non-matrix porosity with 7,749 small megapores, 2,132 large megapores, and 20 gigapores (78.27%, 21.53%, and 0.20% of the 9,901 pores, respectively) and medium matrix porosity. Facies D has low non-matrix porosity with 9,355 small megapores, 2,346 large megapores, and 19 gigapores (79.82%, 20.02%, and 0.16% of the 11,720 pores, respectively) and low matrix porosity. The novelty of this work lies in integrating data from two sources to classify porosity across the Pre-Salt reservoir interval, serving as a proxy for preliminary litho-facies identification without core data. This study advances our understanding of carbonate reservoir sustainability and heterogeneity, offering valuable insights for robust, sustainable reservoir characterization and management in the context of global environmental and geological changes.

This review paper focuses on the joint toxicity and interaction of carbon-based nanomaterials (CNMs) with co-existing pollutants in aquatic environments. It explores the potential harmful effects of chemical mixtures on living organisms, emphasizing the importance of scientific mod-eling to predict mixed toxic effects. The study involved a systematic literature review to gather information on the joint toxicity and interaction between CNMs and various co-contaminants in aquatic settings. A total of 53 publications were chosen and analyzed, categorizing the studies based on the tested CNMs, types of co-contaminants, and the used species. Common test models included fish and microalgae, with zebrafish being the most studied species. The review under-scores the necessity of conducting mixture toxicity testing to assess whether the combined effects of CNMs and co-existing pollutants are additive, synergistic, or antagonistic. The development of in silico models based on the solid foundation of research data represents the best opportunity for joint toxicity prediction, eliminating the need in a great quantity of experimental studies.

Fiber-cement composites were prepared from cellulosic cotton residue (CCR) arise from sanding process (emerizing). The effect of different concentrations: 0.5% and 1%, and granulometry: thick (retained in a14 mesh sieve) and thin (retained in a 48 mesh sieve) of this residue were evaluated on tensile strength of cement slurries with seven (07) curing days. To characterize the CCR, TGA, FT-IR, SEM and XRD analysis were performed and the residue resistance in an alkaline environment was also evaluated. Splitting tensile strength test, known as Brazilian Test, was used to assess effects of the fibers on the mechanical behavior of cement matrix. Analyzing the results, the CCR proved to be resistant in an alkaline environment, meaning that it can withstand the alkaline environment of cement matrix. The results showed an improvement superior to 17% in tensile strength for 1% of CCR. Therefore, the CCR presents a great application potential in cement pastes used for oil well cementing that requires to increase its tensile strength, once a significant improvement was achieved with a low-residue employee.

Background and Objectives: Blood flow restriction (BFR) has been investigated as an alternative method combined with resistance training or AT to promote different health benefits for older people. Nevertheless, no study analyzed chronic effects of BFR on muscle activation in this population, and in some investigations, the application of BFR has been employed arbitrary pressures, which can be a serious methodological error, both from the results and of the risk to the health of the older. Thus, this study analyzed the effect of 24 weeks of walking with BFR on activation and muscle strength in elderly women with osteoporosis. Materials and Methods: Thirty older women (66.0±4.6 years) performed randomly to one of three training groups: WALK (moderate-intensity walking), WALK+BFR (low-intensity walking with BFR), or BFR (BFR alone). Muscle activation (sEMG) and strength of knee flexors and extensors were measured pre-intervention and after 12 and 24 weeks. Results: Only a trivial effect size (ES) for the WALK+BFR (ES= 0.16) was observed in sEMG of the knee flexors compared to WALK. A moderate effect was observed in sEMG of the knee extensors (ES= 0.65) for the WALK+BFR compared to the WALK. However, adverse effects were found in the strength of the knee flexors for the BFR (ES= −0.86) and WALK+BFR (ES= −0.69) compared to WALK. Adverse and null effects, respectively for the BFR (ES= −0.16) and WALK+BFR (ES= 0.06) groups, were also observed on the strength gain of the knee extensors. Conclusions: Low-intensity walk combined with BFR does not provide relevant chronic effects on strength gain or even limit muscle strength gain, however, due to greater activation of knee extensors over 24 weeks, it is possible to benefit from the use of similar strategies to obtain neuromuscular gains in the long‐term for elderly women with osteopenia and osteoporosis.

Fusarium wilt caused by Fusarium oxysporum f. sp. cubense (Foc) is one of the most destructive diseases in banana farming worldwide. Knowledge of the factors of genetic diversity and virulence of the pathogen contributes to the development of resistant cultivars and in management strategies based on exclusion. In this study, phenotypic traits such as virulence and aggressiveness in a sample of 52 Foc isolates, were analyzed and their relationship to the presence of putative effectors of gene SIX (Secreted in Xylem) pathogenicity homologues, verified. According to the dissimilarity matrix, there were three isolates closest to the standard Foc race 1 strain. Isolates 229A and 218A, were selected according to their aggressiveness profile in 'Grand Naine' and 'Prata-Anã', respectively, I order to replace the standard isolate of race 1 in the resistance screening process carried out by the breeding program. Two homologues of the SIX8 gene, SIX8a and SIX8b, are present in isolates of Foc from Brazil and the SIX8b gene correlates with avirulence in the cultivar ‘Grand Naine’ (Cavendish). These results are important to support the banana genetic breeding program by identification of sources of resistance to Foc and contribute in the establishment of the function of SIX effector proteins.

Financial time series and other human-driven, non-natural processes are known to exhibit fat-tailed outcome distributions. That is, such processes demonstrate a greater tendency for extreme outcomes than the normal distribution or other natural distributional processes would predict. We examine the mathematical expectation, or simply "expectation," traditionally the probability-weighted outcome, regarded since the seventeenth century as the mathematical definition of "expectation." However, when considering the "expectation" of an individual confronted with a finite sequence of outcomes, particularly existential outcomes (e.g., a trader with a limited time to perform or lose his position in a trading operation), we find this individual "expects" the median terminal outcome over those finite trials, with the classical seventeenth-century definition being the asymptotic limit as trials increase to this. Since such finite-sequence "expectations" often differ in values from the classic one, so do the optimal allocations (e.g., growth-optimal). We examine these for fat-tailed distributions. The focus is on implementation, and the techniques described can be applied to all distributional forms.

This study explores the impact of regular physical exercise on the quality of life and body image among Para-athletes, emphasizing the necessity of such activities for physical, social, and psychological health. This qualitative study employs content analysis and ethnomethodology to evaluate seven Para-athletes from the Navy's Paralympic Project, using focus group interviews to assess their perceptions. The findings reveal that participation in structured sports programs positively influences body image and quality of life, leading to improved performance in training, social interactions, and competitive events. The analysis suggests that motivation and self-esteem are fundamental to the sporting success of Paralympic athletes. Both external and internal motivations are crucial for sustaining athletic careers and overcoming challenges. Self-esteem enables athletes to remain confident in their abilities, even after setbacks.

Effective water resources management requires assessments of water availability within a framework of complex institutions and infrastructure employed to manage extremely variable stream flow shared by numerous often competing water users and diverse types of use. The Water Rights Analysis Package (WRAP) modeling system is fundamental to water allocation and planning in the state of Texas in the United States. Integration of environmental flow standards into both the modeling system and comprehensive statewide water management is a high priority for continuing research and development. The public domain WRAP software and documentation are generalized for application any place in the world. Lessons learned in developing and implementing the modeling system in Texas are relevant worldwide. The modeling system combines: (1) detailed simulation of water right systems, interstate compacts, international treaties, federal/state/local agreements, and operations of storage and conveyance facilities; (2) simulation of river system hydrology; and (3) statistical frequency and reliability analyses. The continually evolving modeling system has been implemented in Texas by a water management community that includes the state legislature, planning and regulatory agencies, river authorities, water districts, cities, industries, engineering consulting firms, and university researchers. The shared modeling system contributes significantly to integration of water allocation, planning, system operations, and research.

(1) Background: The severity of malaria is associated with low bioavailability of antioxidants and high concentration of free radicals that induce oxidative damage in cerebral and pulmonary microcirculation. This can be prevented by the action of consumable antioxidants present in foods. Therefore, we investigated the protective role of lycopene (LYC) on the oxidative changes induced by Plasmodium berghei (Pb); (2) Methods: Mice were infected by intraperitoneal injection of 106 parasitized red blood cells and treated via gavage with LYC (3.11 mg/kg bw/day) or NAC (62 mg/kg bw/day). They were then evaluated for 1, 4, 8 or 12 days after infection. Levels of thiobarbituric acid reactive substances (TBARS), antioxidant capacity by inhibition of ABTS radicals (AC-ABTS) and DPPH (AC-DPPH), uric acid (UA), and nitric oxide (NO) were measured in brain and lung tissues; (3) Results: The infection caused oxidative stress confirmed by increased levels of TBARS, AC-ABTS, AC-DPPH, UA, and NO in the tissues leading to the death of the animals. LYC prevented the increase in TBARS, AU, and NO levels compared to Pb (p< 0.0001) and NAC+Pb groups (p<0.0001), reaching values similar to those of Sham animals; (4) Conclusions: These results are striking evidence of the beneficial effect of lycopene supplementation on oxidative stress in experimental malaria in vivo and emphasize the importance of antioxidant supplementation in the treatment of the disease.

An important indicator of human-related pollution in watersheds is dissolved oxygen (DO). The DO is highly dependent on both space and time characteristics of the watershed and is directly linked to eutrophication, which impairs the development of both the aquatic fauna and flora, also negatively impacting the water quality. Aspiring to reach a more accurate and precise forecasting approach to predict levels of DO, the present work proposes new graph-based and transformer-based deep learning models. The models were trained and validated for the Credit River Watershed, and the results were compared with both benchmarking and literature-found approaches. The proposed Graph Neural Network Sample and Aggregate (GNN-SAGE) model was the best-performing approach, reaching coefficient of determination (R2) and Root Mean Squared Error (RMSE) values of 97% and 0.34 ppm, respectively. The findings from the Shapley additive explanations (SHAP) indicated that the GNN-SAGE benefited from spatiotemporal information from the surrounding stations, improving the model’s results, and that temperature is a major input attribute for determining future DO levels. The results established that the proposed GNN-SAGE model stands as a state-of-the-art solution for DO forecasting, with potential for real-time water quality applications.

Diabetes Mellitus is one of the most prevalent chronic diseases in the world and one of its main features is chronic hyperglycemia. Among the therapeutic forms used to control the pathology are pharmacotherapy and the use of other alternatives such as regular exercise, which participates in glycemic control and the ingestion of plant extracts with antioxidant effects in the body. Among the different plants used, curcumin is a possible plant to be used to attenuate the hyperglycemic picture triggered by Diabetes Mellitus. Some studies suggest that this plant is antioxidant and hypoglycemic. The review aimed to know the antioxidant and hypoglycemic potential of curcumin supplementation in DM. The search was performed considering articles published between 2010 to 2019, in English and Portuguese, and a theoretical survey of relevant information was conducted in the main databases of scientific publications: Virtual Health Library and its indexed databases as Pubmed, LILACS, Scielo and Scientific Electronic Library Online. The associated use Turmeric and Physical Exercise demonstrated antioxidant, anti-inflammatory and hypoglycemic activity caused by Diabetes Mellitus. We may suggest that these are potential therapeutic ways to improve the quality and survival of diabetic patients.

The pandemic of Covid-19 has contributed to the increase of the number of cases of anxiety, depression, and stress, especially in vulnerable workers. The objective of this study was to analyze factors associated with mental health of waste pickers and street sweepers in Brasília, Brazil, during the Covid-19 pandemic. It was a cross-sectional cohort study with a quantitative approach. SRQ-20 test was used to assess mental health. The study sample included 886 workers: 601 street sweepers and 285 waste pickers. Of the total, 71 workers (8.0%) had SRQ-20 ≥ 7, which is equivalent to adverse mental health. The characteristics associated with adverse mental health were women (PR: 3.36; 95%CI:1.86;6.08), worker between 18-39 years old (PR: 2.19; 95% CI 1.32;3.65), waste pickers (PR: 1.65; 95%CI:1.01;2.70), worker who reported two (PR: 3.24; 95%CI:1.72; 6.12), three or more (PR: 4.73; 95%CI:2.40;9.32) health problems. For the symptoms, 17.05% of the people interviewed said they felt sad and 18.25% nervous, tense, and worried. Female waste pickers, young adults, with many health problems were more susceptible to adverse mental health and it doesn't just affect them, but also their families. Public policies are needed to protect these professionals so that they can work safely and establish early interventions to maintain these workers' mental integrity.

The Brazilian economy, the rural in particular, was until the end of the 19th century based on slave labour. In this research, it was intended to obtain, through a review of historical descriptive studies, a detailed picture of the occupational hygiene conditions related to the slaves’ work and their interactions with climatic and environmental conditions. The search was done in the following databases: Science Direct, Scopus, Web of Science, Criminal Justice, Ebsco, Business Source Supplement, as well as original historical documents. Descriptive studies, without the restriction of language, were selected that involved the rural work of slaves in colonial and imperial Brazil. Working environmental conditions have been evaluated: environmental and occupational hygiene conditions to which the captive workers were exposed, as well as their accommodation and clothing. The analysed studies registered the existence of accommodation and similar dresses all over Brazil, regardless of the region's climate. In addition to these accommodation conditions, slaves were still exposed in a similar way to physical, chemical and biological agents throughout the country. Finally, it was also possible to identify a clear similarity with the occupational exposure conditions of the modern slaves in the 21^st century.

Background: Post-operative pain and swelling are frequently observed after sinus lift procedures. The aim of the present study was a clinical evaluation of swelling and pain of two sinus lift different flaps technique measured through visual analogue scale (VAS), verbal rating scale (VRS) and infrared thermal imaging (i.e., thermography). Methods: A randomized controlled trial was conducted in fifteen patients treated for a total of 30 sinus randomly allotted into two groups. In patients of Group I, a triangular flap was performed, while in Group II modified triangular flap without anterior release was performed. Postoperative pain was scored by VAS and inflammation was recorded by VRS at 2, 4, 6 and 14 days. The facial temperature was recorded before and after sinus augmentation, at 2, 4, 6 day intervals for the first week and at 14 day, to check the course of healing. Results: In group I the pain intensity was recorded at 2 days after the surgery with a score of 38.67 ± 6.4 mm. Swelling was higher at 2 and 4 day, and it was absent at day 6. Facial temperature difference before and after the procedure was 3 (4.737 °C ± 0.37). In Group II the pain was lower than in Group I (p < 0,05). Swelling scored 2 on the first and second day, and it was reduced at day 4. After the second day the difference of temperature reduced significantly compared to day of surgery (0.77 °C), at 2 and 4 days no difference was registered. Conclusion: In conclusion based on the outcome of the present study, modified triangular flap can be used with success in sinus augmentation procedures and is to be preferred to trapezoidal flap.

Signaling modules that integrate the diverse extra- and intracellular inputs to control cell proliferation are essential during both development and adult stages to guarantee organism homeostasis. Mobs are small adaptor proteins that participate in several of these signalling pathways. Here we review recent advances unraveling Mob4 cellular functions, a highly conserved non-catalytic protein, that plays a diversity of roles in cell proliferation, sperm cell differentiation and simultaneously is involved in synapse formation and neural development. In addition, the gene is often overexpressed in a wide range of tumors and is linked to poor clinical outcomes. Nevertheless, Mob4 molecular functions remain poorly defined, although it integrates the core structure of STRIPAK, a kinase/phosphatase protein complex, that can act upstream of the Hippo pathway. In this review we focus on the recent findings of Mob4 functions, that have begun to clarify its critical role on cell proliferation and development of tissues and individuals.

Considering the health benefits of the kombucha, already widely studied, the objective of the study was to development of the beverage with the addition of infusion of special arabica coffee from the first fermentation varying the proportion of special coffee (2% a 13%) and evaluate the pH, volatile acidity, degree of alcohol, centesimal composition, sodium contents, colour parameters as like acceptability of the beverages. With respect to the pH, all the formulations conformed with the kombucha identity standard, but K3 and K4 were below the established minimum for volatile acidity. Except for K4, all the other formulations were classified as alcoholic kombuchas, although the values were very close to the limit for non-alcoholic. The formulations presented low sugar and sodium content, which corroborated the low caloric value. Therefore, coffee-flavored kombucha fermented for 18 days becomes an option for consumers looking for low-calorie, refreshing and healthy drinks. The luminosity of the beverages decreased as the proportion of coffee increased, and consequently the values for a* and b* increased, indicating a strong tendency for a yellowish red colour. Sensorially, the formulations K4 and K3 were the most well accepted in all respects and can therefore be considered formulations with high commercialization potential.

As a result of the cancer immunotherapy revolution hundreds of clinical trials of the newly approved immunotherapies are now under way to improve responses. Not unexpectedly, the 2018 Nobel Prize in Physiology or Medicine was awarded to James P. Allison and Tasuku Honjo for their development of cancer therapy by blockade of co-inhibitory signals. While success stories of terminal cancer patients achieving complete remissions are accumulating, not enough research has been done into the risks of the new therapies. Since the use of immunotherapy is becoming more common, and is expected to develop into first- and second-line treatments, immunotoxicity and autoimmunity are emerging as the nemesis of immunotherapy. Immune-related adverse events (IrAEs) could affect any tissue, their incidence may reach up to 90% of patients and toxicity is dose-dependent. While the combination of two immune checkpoint inhibitors (ICIs) increased efficacy, the incidence of severe adverse events was also increased. Apparently, ICIs cannot be restricted to the targeted anti-tumor T cell population. The long lasting objective of cancer regression can only be achieved by paying a price: tolerance to healthy self tissues is compromised. In the face of an ipilimumab induced pan-lymphocytic activation, a therapeutic paradigm shift is required. The task is not desperately trying to put the genie back in the bottle by immune suppressive treatments, but instead harnessing the autoimmune forces by an off label low-dose combined anti-CTLA-4 and anti-PD1 antibody blockade, which is supplemented with conventional interleukin-2 stimulation and hyperthermia. The proof-of-principle of the low-dose-combination therapy was demonstrated in a heavily pre-treated triple negative breast cancer (TNBC) patient with far advanced pulmonary metastases and severe shortness of breath, who had exhausted all conventional treatment. Her pulmonary metastases went into complete remission with transient WHO I-II diarrhea and skin rash. She lived for 27 months after starting the low-dose-combination therapy. She had recurrence as a sternal mass and pleural metastases up to 3 cm. Since the low-dose-combination protocol consists only of approved drugs and treatments, this exceptional response should instigate further research efforts.

The Brazilian livestock is predominantly extensive, with approximately 90% of the production being sustained on pasture, which occupies around 20% of the territory. In the current climate change scenario and where cropland is becoming a limited resource, there is a growing need for a more efficient land use and occupation. It is estimated that more than half of the Brazilian pastures have some level of degradation; however there is still no mapping of the quality of pastures on a national scale. In this study, we mapped and evaluated the spatio-temporal dynamics of pasture quality in Brazil, between 2010 and 2018, considering three classes of degradation: Absent (D0), Intermediate (D1), and Severe (D2). There was no variation in the total area occupied by pastures in the evaluated period, in spite of the accentuated spatial dynamics, with a retraction in the center-south and expansion to the north, over areas of ​​native vegetation. The percentage of non-degraded pastures increased ~12%, due to the recovery of degraded areas and the emergence of new pasture areas as a result of the prevailing spatial dynamics. However, about 44 Mha of the pasture area is currently severely degraded. The dynamics in pasture quality were not homogeneous in property size classes. We observed that in the approximately 2.68 million properties with livestock activity, the proportion with quality gains was twice as low in small properties compared to large ones, and the proportion with losses was three times greater, showing an increase in inequality between properties with more and less resources (large and small, respectively). The areas occupied by pastures in Brazil present an unique opportunity to increase livestock production and make available areas for agriculture, without the need for new deforestation in the coming decades.

In cold-climate regions, road salt is used as a de-icer for winter road maintenance. The applied road salt melts ice and snow on roads, being washed off through storm sewer systems into nearby urban streams, harming the freshwater ecosystem. Addressing the gap in the knowledge regarding the use of deep learning approaches for urban stream water quality forecasting, the present work discusses our implementation of a “Graph Neural Network” - “Sample and Aggregate” (GNN-SAGE) model for forecasting chloride concentrations in the Credit River in Ontario, Canada. The proposed GNN-SAGE is compared to other models, including a Deep Neural Network based transformer (DNN-Transformer) and a benchmarking persistence model for 6 hours forecasting horizon. Ac-cording to the results, the GNN-SAGE model surpasses other models in providing accurate predic-tions of chloride concentrations within the assessed prediction window. Also, a SHAP analysis provides insight into the variables that influence the model’s forecasting, showing the impact of the spatiotemporal neighbouring data from the network and the seasonality variables on the model’s result. The GNN-SAGE model shows potential for use in real-time forecasting of water quality in urban streams, aiding in the development of regulatory policies to protect the vulnerable freshwater ecosystems in urban areas.

Sugarcane plays a crucial role in global sugar and ethanol production. Conventionally, sugar-cane propagation involves planting billets. However, Brazilian researchers have introduced the innovative pre-sprouted seedlings (PSS) method, widely used in the MEIOSI (Simultaneously Occurring Interrotational Method) system. Although MPB has several advantages over the con-ventional method, its sensitivity to water scarcity is a challenge. The study aimed to evaluate the survival and growth of PSS inoculated with Bacillus licheniformis and Bacillus subtilis under differ-ent water regimes. The experiment was conducted in the field in a randomized block in strips (split-block) using a 2×4 factorial scheme consisting of two inoculation conditions (with and without bacteria) and four water regimes (0%, 33%, 66%, and 100% of the ideal irrigation). The bacteria increased the PSS's survival and water use efficiency in the field. In addition, inocula-tion increased root and shoot growth, as well as the nutrient uptake such as N, P, Mn, Zn, and Cu, which resulted in a higher number of stalks per meter and, therefore, a higher multiplica-tion rate in the MEIOSI system. Inoculation proved to be a promising alternative for establishing PSS under water restriction.

Purpose: The goal of this article was to introduce a new technique for root coverage (RC), the Mixed-Thickness Tunnel access (MiTT), approaching a full-split design, showing the results obtained in a case series and demonstrating it step-by-step. Methods: Healthy individuals, non-smokers, and non-diabetics, who were diagnosed with gingival recession (GR) type 1 or 2 (RT1 or RT2). After all necessary evaluations, prophylaxis was performed 14 days before the surgical procedure. Then, after the basics clinical conduct and anesthesia, one or two vertical incision(s) on the mucosa (around 1-2 mm apical to the MGJ), lateral to the papilla base, were done. Initial detachment of the mucosa from the muscles (split design); it was permitted (but not mandatory) to do intrasulcular incisions; from the MGJ to coronal, subperiosteal access was done to raise the full-thickness tunnel. It must communicate up to the gingival sulcus area and the papilla’s base, keeping the papilla’s tip intact. A connective tissue graft was harvested, which was inserted through the linear incision or intrasulcularly. Interrupted sutures were done and may be used as adjunctive material. Results: Nine healthy individuals (7 females and 2 males) aged 19 and 43 years were enrolled. They were treated following the MiTT steps. There were four cases with a single GR, 2 patients with 2 teeth involved, and three with 3 or 4 GR. Seven cases were RT1 and two RT2. All RT1 cases achieved 100% RC, while the mean RC obtained for RT2 was around 80%. Conclusion: MiTT can be considered a more straightforward approach for minimally invasive surgical technique, which is a feasible option to treat RC with a high success rate, predictability, and esthetic preservation. There is a technical sensitivity to performing the full-split design procedure.

Dementia is a rising public health concern. Feeding and nutritional problems increase as the disease progresses, affecting clinical course and caregiver burden. While some guidelines advise against percutaneous endoscopic gastrostomy (PEG) and tube feeding in advanced dementia, conflicting evidence exists. This study aims evaluating nutritional status and the influence of PEG-feeding on outcome and evolution of nutritional/progonosis markers of patients with severe dementia (PWSD) who underwent gastrostomy for nutritional support. We conducted a 16-year rectrospective study on 100 PEG-fed PWSD with strong familiar support. We evaluated survival PEG-feeding period, safety, and objective nutritional/progonosis data at the gastrostomy day and after 3 months: Body Mass Index (BMI), Mid Upper Arm Circumference, Tricipital Skinfold, Mid-Arm Muscle Circumference, albumin, transferrin, total cholesterol and hemoglobin. Most patients presented low values in these nutritional/progonosis parameters. No major life-threatening PEG complications were reported. The mean survival time after gastrostomy was 27.9 months (median of 17 months). Female sex, BMI recovery at 3 months, and higher baseline hemoglobin levels were associated with a reduced risk of death and increased survival time. The study concluded that, in carefully selected PWSD with strong familiar support, PEG feeding can improve nutritional status and have a positive impact on survival.

Zircon xenocrysts from alkali basalts in Ratanakiri Province, Cambodia, represent a unique low-Hf zircon, within a 12,000 km long Indo-Pacific megacryst zone. Colourless, yellow, brown and red crystals ({100}, {101}, subordinate {211}, {1103}), with hopper growth and corrosion features, range up to 20 cm in size. Zircon chemistry implicates juvenile, Zr-saturated, mantle-derived alkaline melt (Hf 0.6–0.7 wt%, Y <0.2 wt%, U+Th+REE <600 ppm, Zr/Hf 66–92, Eu/Eu*_N ~ 1, positive Ce/Ce*_N, HREE enrichment). Incompatible element depletion with increasing Yb/Sm_N from core to rim at ~ constant Hf suggests single stage growth. Ti-in-zircon temperatures (~570–740 °C) are lower than predicted by crystal morphology (800–900 °C) and decrease from core to rim (D_T = 10–50 °C). The d¹⁸O values (4.88 to 5.01‰ VSMOW) are relatively low for xenocrysts from the zircon Indo-Pacific zone (ZIP). The ¹⁷⁶Hf/¹⁷⁷Hf values (+ εHf 4.5–10.2) give T_{Depleted Mantle} model source ages of 260–462 Ma and T_Crustal ages of 391–754 Ma. The source magmas reflect variably depleted lithospheric mantle with little supracrustal input. Zircon U-Pb (0.88–1.56 Ma) and (U-Th)/He (0.86–1.02 Ma) ages are older than host basalt ages (~0.7 Ma), suggesting limited residence before transport. Zircon genesis suggests Zr-saturated, Al-undersaturated, carbonatitic-influenced, low-degree partial melting (<1%) of peridotitic mantle at ~60 km beneath the Indochina terrane.

Anti-inflammatory agents are widely used for the treatment of inflammatory diseases. Nevertheless, the associated side effects of available drugs make necessary the search for new anti-inflammatory conditions. Here, we investigated the anti-inflammatory activity of solidagenone. Initially, we observed that a single dose of 30, 60 or 90 mg/Kg of solidagenone did not result in mortality or elicit any discernible signs of toxicity in the animals. At the same doses, solidagenone promoted a significative reduction in the migration of neutrophils in an acute peritonitis model and decreased mortality in a lipopolysaccharide-induced endotoxic shock model. Interestingly, treatment with solidagenone conferred a protective effect against leukopenia and thrombocytopenia, hematological disorders commonly observed in sepsis conditions. In addition, treatment with all the doses of solidagenone promoted a significative reduction in nitric oxide, TNF-α, and IL-1β relative to the LPS-stimulated vehicle-treated cultures. Furthermore, gene expression and in silico analyses also supported the modulation of NF-κB pathway by solidagenone. Finally, in silico pharmacokinetics prediction indicated a favorable drugability profile for solidagenone. Taken together, the findings of the present investigation show that solidagenone exhibits significant anti-inflammatory properties in acute experimental models, potentially through the modulation of NF-κB signaling pathway.

This study aims to provide a comprehensive analysis of the More Light for Amazon (MLA) program, examining the roles played by each stakeholder involved in the concession process and identifying the limitations faced for program success. The research employs a content analysis methodology, analyzing a variety of documents, including the Program Operational Manual, Commitment Terms, news articles, and concessionaires' notes. The findings reveal the crucial role of the government as an inducer of actions, establishing objectives and guiding norms for the private sector. Conversely, concessionaires assume the role of program implementers but encounter specific limitations in remote locations, challenging the provision and maintenance of the electrical system in beneficiary communities. The implementation of microgrid systems through concessions enhances coordination and integration between generation and distribution services, allowing for increased government control and ensuring transparency, efficiency, and program effectiveness. These identified elements represent significant challenges for the implementation of public policies in remote regions of the Amazon. Overcoming these challenges take coordinated and strategic actions involving both the government and concessionaires to ensure the complete fulfillment of energy needs in MLA program beneficiary communities.

Background and objectives: due to the neurotoxic effect caused by high levels of cortisol, studies suggest that stress and certain psychiatric disorders, such as mood disorders, have influences under the hippocampus, causing a decrease in volume and consequent memory changes. This study aims to evaluate the relationship between hippocampal volume in patients with mood disorders under therapy. Materials and Methods: the PRISMA protocol for systematic reviews was followed. Pubmed, Cochraine and Scielo databases were searched by terms “Hippocampus”, “Mood Disorders” and “MRI”, and variants in other languages, in human, from January 2011 to September 2016. The individual quality of the articles was analyzed using the Cochraine modified scale for clinical trials and the Agency for Healthcare Research and Quality scale for observational studies. Results: all studies showed reduction of hippocampal volume in depressive patients. Change in hippocampal volume is not related to the use of antidepressant. Particularly the sub-region of the subculum is more reduced, without lateralizations. Significant relationship between stress and right hippocampal reduction. The findings seem to point out: a common pathway of hippocampus reduction, mediated by stress, explaining memory deficits due to depression, where the cortisol pathway seems to act; alteration in the prefrontal cortex; reduction in the subiculum related to inhibition of the hypothalamic-pituitary-adrenal axis, corroborating the hypothesis of cortisol. Conclusions: the papers suggest: association between global hippocampal atrophy with mood disorders; reduction of hippocampal subiculum; refractoriness to clinical treatment among patients with lower hippocampal volume.

The civil construction industry is one of the sectors that most consume natural resources in the world and, consequently, one of that generate more waste. Thinking about constructive techniques that generate less impact on the environment is vital to ensure sustainable development. In this scenario, the Life Cycle Assessment (LCA) has been presented as an internationally recognized approach, that assesses the potential impact of products and services on human health and the environment, throughout its entire life cycle. Aimed to identify construction techniques and vertical closing systems that generate less impact and consumption of natural resources, the impacts generated by the life cycle of the three vertical closing systems most applied in construction sites in Brazil were compared: ceramic brick masonry system (CBr); concrete block masonry system (CBk); and structural blocks masonry system (SBk). The SBk proved to be the least impacting to the “Resource Scarcity”, “Damage to Human Health”, and “Damage to the diversity of Ecosystems” interesting areas. This performance is directly related to the use of cement CPIII type and also by the fact that the SBk consumes less concrete and mortar than the others. Already the "Water Consumption" area, the CBk was the least impacting due to the lower consumption of electricity during its life cycle. The reliability of the results was proven through a sensitivity analysis of the normalization and characterization factors, which consisted of comparing the results obtained by applying two different methodologies. It is believed that the LCA study carried out can assist in the decision-making process regarding the choice of the most sustainable construction method.

The atherosclerosis, a chronic and inflammatory disease that occurs when there are high levels of low-density lipoprotein (LDL) on plasma. This important risk factor for development of cardiovascular disease (CVD) is the main cause of death worldwide. MicroRNAs have recently emerged as potential biomarkers and therapeutic target for lipid metabolism disorders. In this review, we will provide profile of surrounding miRNAs that have demonstrated being regulators of PCSK9, LDLR and APOB100 genes. Recent work has identified the mir-148, mir-128, mir-27a/b, mir-185, mir-301, mir-130 as important regulators of this pathway because they decrease supply of LDL receptors through interaction with PCSK9. Inhibition of LDLR expression cause elevation of plasma LDL levels which induces atherosclerosis. While mir-30c, mir-122, mir-34 decrease MTTP, which promotes degradation of APOB100 preventing assembly and secretion of VLDL. We conclude that, when overexpressed, mir-148a, mir128 and mir-27a/b, mir-122 and mir-34 are related to decrease in LDLR, facilitating occurrence of atherosclerosis. While mir-30 has been linked to decreased atherosclerosis. Detection of miRNAs profile could be used in the future as a biomarker for disturbs linked to c-LDL uptake and in future anti-miRNAs therapies may be used in the treatment of atherosclerosis.

Abstract: Rotavirus (RV) it’s the agent of one of the main causes of severe viral gastroenteritis in the pediatric population, being responsible for a significant portion of deaths related to diarrhea among children under five years. RV are identified as a potential reference pathogen and it is known that the persistence and infectivity of the viral particles can be related to environmental factors. The aim of the study was to identify and correlate the presence of Rotavirus in collective and individual water sources (deep tubular wells, shallow tubular wells, shallow dug wells, springs, surface water, rainwater stored in cisterns and water trucks that were collected from surface water) of rural communities in the state of Goiás, with the seasons in which the collections were made (rainy and dry season). For this, 86 water samples in the dry period and 160 samples in the rainy period were collected. Concentration of water samples, extraction of viral genetic material, cDNA synthesis and molecular tests (qPCR) were performed. When analyzing the presence of RV in the samples in relation to the period studied, RV was found to be more prevalent in the dry season (54.7%) than in the rainy season (20%), showing a strong statistical association with the dry season (p-value < 0.001). The proportion of positive samples in the dry period, considering the type of source, resulted in higher in Shallow dug wells (p-value <0.001), higher in surface waters (p = 0.001) and higher in spring water (p-value = 0.02). The presence of pathogenic microorganisms in water is a public risk problem, enabling the emergence of outbreaks, endemics and epidemics. In the present research, there was an association among the presence of Rotavirus and the dry period of the year, when compared to the rainy period. Describing or identifying the seasonal behavior of pathogens is important for prevention and attention to water treatment and help in the monitoring of the virus in the water sources.

The Eucalyptus genus is the most planted forest crop in the world, with Brazil being one of the countries with the greatest productive potential. However, the occurrence of weeds can cause losses in productivity. Chemical control is widely used, but the efficiency of herbicides depends on factors such as the presence of straw in the soil and the occurrence of rainfall. Due to the scarcity of results regarding the interaction between herbicide, straw, and water depth in the forest sector, the objective of this study is to evaluate the efficiency of S-metolachlor + glyphosate in the control of grasses in different densities of eucalyptus straw and with simulated rain after the application of the product. The experiment was conducted in DBC, factorial 3×3×2, with four replications. The first factor represented 0, 50 and 100% of the commercial dose of S-metolachlor + glyphosate, the second 0, 5, and 10 ton ha-2 of straw, and the third 25 and 50mm of water depth applied in soil with a mix of grasses previously sowed. The rainfall simulation was performed 24 hours after herbicide application on each straw volume. The fresh mass of the aerial part of the grasses was collected 43 days after sowing and dried in an oven to determine the dry mass. Visual analyzes of the percentage of control were performed with scales ranging from 0 to 100, where 0 represents no control and 100 efficient control. The fresh and dry mass and the grasses' dry mass/water ratio decreased with increasing herbicide dosage and straw density. The dosage of 2.12 + 1.59 kg i.a. ha-1 of S-metolachlor + glyphosate resulted in greater control of grasses, and the treatments without straw and with the application of the herbicide had the highest percentages of control. Applying different water depths (25 mm or 50 mm) did not influence the control. Despite the control of grasses, the efficiency of the herbicide mixture was affected by the presence of vegetation cover.

The use of optical fibers is increasing in modern aircraft because it helps solve challenges of size, weight, communication, and reliability in new aircraft generation. This work describes a video and power transmission system using optical fibers (PoF) for in-flight entertainment (IFE) system application. We present the benefits and the limitations of this application, and we perform two practical experiments to demonstrate their performance. It used off-the-shelf devices in the experiments, such as one 15-W semiconductor laser operating at 808 nm, GaAs photovoltaic converters, optical transmitters and receivers, and video monitors. The power and video signals were transmitted using two 50-m multimode fibers. In addition, we proposed and tested two types of energy transformation units (ETU), which are responsible for supplying electrical energy to the IFE video monitor and the optical fiber receiver.

Turbidity is an important indicator of water quality in hydrology. More traditional ways to monitor turbidity can provide reliable results. However, they are prone to human error, have elevated costs, and lack real-time monitoring capacity. Addressing these hindrances, in this work we combine spectral bands and indices from Sentinel-2 with several machine learning paradigms, namely XGBoost, Random Forests, GMDH, Support Vector Regression, k-Nearest Neighbors and Least Absolute Shrinkage and Selection Operator to model turbidity, using data from twelve monitoring stations encompassing the Mississippi River, USA. Results show that considering the individual monitoring stations, the ML paradigms for turbidity modeling were satisfactory at locations with a larger range and standard deviation values, achieving a mean R2 value of 59.5%. Tree-based models were the best overall approach, often ranking as the best or second-best performing model. When all the samples from the monitoring stations were used, the XGBoost provided superior output for turbidity modeling, reaching an R2 equal to 75.7%. A comprehensive comparison with the literature found values showed that the models implemented using this study’s methodology could provide competitive results, deeming it as an alternative for turbidity modeling from remote sensing data.

Titica vine fibers (TVFs) extracted from aerial roots of Heteropsis flexuosa, from the Amazon region, were 10, 20, 30 and 40 vol% incorporated into an epoxy matrix for applications in ballistic multilayered armor systems (MASs) and stand-alone tests for personal protection against high-velocity 7.62 mm ammunition. The back-face signature (BFS) depth measured for composites with 20 and 40 vol% TVFs used as an intermediate layer in MASs was 25.6 and 32.5 mm, respectively, below the maximum limit set by the international standard. Fracture mechanisms found by scanning electron microscopy (SEM) attested the relevance of increasing the fiber fraction for applications in MASs. The results of stand-alone tests showed that the control (0 vol%) and samples with 20 vol% TVFs absorbed the highest impact energy (Eabs) (212 – 176 J), and consequently limit velocity (VL) values (213 – 194 m/s), when compared with 40 vol% fiber fractions. However, the macroscopic evaluation found that the plain epoxy, referring to control samples, shattered completely. In addition, for 10 and 20 vol% TVFs, the composites were fragmented or exhibited delamination fracture, which contributed to their physical integrity. On the other hand, the composite with 30 and 40 vol% TVFs, whose Eabs and VL varied between 166 – 130 J and 189 – 167 m/s, respectively, showed the best dimensional stability. The SEM images indicated that for composites with 10 and 20 vol% TVFs the fracture mode was predominantly brittle, due to the greater performance of the epoxy resin and the discrete action of the fibers. While for composites with 30 and 40 vol% TVFs, there was the activation of more complex mechanisms such as pullout, shearing and fiber rupture.

Baía de Todos os Santos is the second largest bay in Brazil and is home to important ecosystems, including estuarine systems and mangroves. However, studies on the seasonal variability of its soil properties and composition are still scarce. For this study, soil and leaf samples were seasonally collected from mangrove forests at four sites (Cacha Prego, Ponta Grossa, Ilha de Maré, and Pitinga), which are representative of different environmental conditions within the BTS. Soil physicochemical properties, soil composition and partition of Fe forms were determined, and analysis of minerals by Scanning Electron Microscope, was performed on soil samples. Isotopic ratios (δ13C, δ15N) were also determined on soil and leaf samples. Soils showed significant spatial and temporal changes affecting both their properties (pH, Eh) and their composition (TOC, pyrite and Fe oxyhydroxide contents). Clear spatial changes were observed in redox potential, significantly affecting the concentrations of the different geochemical forms of Fe, particularly the concentrations of crystalline oxyhydroxydes and pyrite in one of the studied sites. In three of the study sites, pyrite crystals showed clear evidence of degradation associated with sandy soils. Finally, δ13C and N/C ratios in soils seem to suggest a mixed origin of organic matter.

In order to monitor the diversity of terrestrial biomes, the Earth Exploration Satellite Services demand a high data rate for downlink transmissions while sharing their frequency spectrum with, and suffering interferences from, cellular Base Stations. Both highlight the dilemmas of spectral efficiency (bps/Hz) and spectral coexistence. Our research aims to mitigate interference on low orbit satellite downlinks using Cognitive Radio (CR) and Adaptive MODulation and CODing (MODCOD) techniques. To fulfill this: 1) we present CR approaches to enhance spectrum exploitation. Next, 2) we detail Adaptive MODCOD (ACM) technique to increase RF power and spectral efficiencies. Then, 3) we suggest the solution by combining 1) and 2). Afterwards, 4) we analyze it by monitoring the signal to interference plus noise ratio and the CR/MODCOD strategy. Finally, 5) we provide case studies to demonstrate the strategy’s effectiveness through the practical operation of satellite services, and 6) we conduct a bench test of the communication system.

Malassezia species are part of human commensal microbiota and is also related to diseases. Little is known about the interaction of these microorganisms with their host. Here we established two standard culture conditions for Malassezia spp. to perform infection assays using C. elegans and T. molitor. Invertebrate hosts infected by Malassezia spp. cultured in M9M resulted in higher death rate on survival assays when compared to yeasts cultured in standard Dixon medium indicating that M9M cultured Malassezia species have increased virulence. The culture and infection conditions established in this work, using invertebrate alternative models, are valuable tools to understand Malassezia-host interaction.

In this paper, solar irradiance and wind speed forecasts were performed considering time horizons ranging from 10 min to 60 min, under a 10 min time-step. Global horizontal irradiance (GHI) and wind speed were computed using four forecasting models (Random Forest, k-Nearest Neighbours, Support Vector Regression, and Elastic Net) to compare their performance against two alternative dynamic ensemble methods (windowing and arbitrating). Forecasting models and dynamic forecasting ensembles were implemented in Python for performance evaluation. The performance comparison between the prediction models and the dynamic ensemble methods was carried out by evaluating the RMSE, MAE, R² and MAPE, to evaluate whether the dynamic ensemble forecasting method obtained greater. According to the results obtained windowing dynamic ensemble method was the most efficient among the tested. For the wind speed data, by varying its parameter λ (from 1 to 100), a variable performance profile was obtained, where from λ =1 to λ = 74, windowing proved to be the most efficient, reaching maximum efficiency for λ = 19. Windowing was the best method for the GHI analysis, reaching its best performance for λ = 1. The efficiency gain using windowing was 0.56% when using the wind speed model and 1.96% for GHI.

Background: Clinical cases reports with snake accidents show that venom bite induces increased oxidative stress including several markers of lipid peroxidation and other oxidative stress marker in plasma. Methods: The main findings of this work were performed with BthTx-II on paw edema of animals treated with the toxin and biochemical measurement of COX-2, PGE2, MDA and the effects of peroxiredoxin inhibitors on edema and myotoxicity were also evaluated. Results: The results show that edema and myotoxocity induced by PLA2 (BthTx-II) induces a strong mobilization of arachidonic acid and an increase in cellular oxidative stress as measured by increased malondialdehydo (MDA) concentration and protein carbonylation. Thus, these findings establish the strong link between oxidative stress, arachidonic acid mobilization and that these events may explain the presence of oxidative stress markers in snake-bitten patients. Experiments performed with animals previously treated with commercially purchased inhibitors showed enzymes such as thioredoxin (TXN), thioredoxin reductase (TXNRD) and other glutathione (GSH)-related antioxidant defenses could play an essential role controlling and defining the end of edema on the late phase of PLA2 BthTx-II-induced process. Conclusion. This study showed that thioate-dependent antioxidant enzymes play an important role in resolving the edema induced by BthTx-II.

In view of the diminishing contribution of natural products from plants to the discovery of new chemical structures, the aim of this study was to compile the articles from 2021 to 2022, assessing: (1) which classes of compounds these new structures belong to; (2) which plants and families these compounds belong to and (3) assessing the degree of novelty of the compound with an already known structure. The review was elaborate following the Preferred Reporting Items for System-atics Reviews and Meta-analyses (PRISMA) statement checklist for guide reporting of systematic reviews. A total of 464 articles were selected for the new compounds of natural origin survey. We included 117 complete articles in this review and reported approximately 109 new structures elucidated during the years 2021 and 2022. Many of the compounds showed small structural var-iations in relation to already known molecules. For some, however, this small modification was decisive for the biological activity reported, demonstrating the importance of descriptive phytochemical studies.

Aims: This systematic review aims to evaluate the influence of Environmental Enrichment (EE) on oncological factors in experimental studies involving various types of cancer models. Methods: A comprehensive search was conducted in three databases: PubMed (161 articles), Embase (335 articles), and Scopus (274 articles). Eligibility criteria were applied based on the PICOS strategy to minimize bias. Two independent researchers performed the searches, with a third participant resolving any discrepancies. The selected articles were analyzed, and data regarding sample characteristics and EE protocols were extracted. The outcomes focused solely on cancer and tumor-related parameters, including cancer type, description of the cancer model, angiogenesis, tumor occurrence, volume, weight, mice with tumors, and tumor inhibition rate. Key-findings: A total of 770 articles were identified across the three databases, with 12 studies meeting the inclusion criteria for this systematic review. The findings demonstrated that different EE protocols were effective in significantly reducing various aspects of tumor growth and development, such as angiogenesis, volume, weight, and the number of mice with tumors. Furthermore, EE enhanced the rate of tumor inhibition in mouse cancer models. Findings: This systematic review highlights the significant impact of EE protocols on multiple parameters associated with tumor growth and development, including angiogenesis, occurrence, volume, weight, and tumor incidence. Moreover, EE demonstrated the potential to increase the rate of tumor inhibition. These findings underscore the importance of EE as a valuable tool in the management of cancer.

Breast cancer represents the most common neoplasm worldwide. Viral infections are involved with carcinogenesis, especially those caused by oncogenic Human Papillomavirus (HPV) genotypes. The relationship between HPV and various types of cancer, such as breast and lung, still requires further studies. After infection with HPV, there is a remodeling of the tumor microenvironment, providing a post-infection alteration with immunosuppressive characteristics. This study evaluated the role of HPV in breast adenocarcinoma cell lineage (MDA-MB-231), transfected with the HPV16 E5, E6, and E7 oncogenes and co-cultured with PBMCs. Immunophenotyping was performed. There was an increase in CD4+ T cells number when compared with non-transfected and transfected MDA-MB-231, especially the Treg profile. Moreover, proinflammatory intracellular cytokines, such as IFN-γ, TNF-α, and IL-17 were impaired by transfected cells and a decrease in the cytolytic ac-tivity of the CD8+ and CD56+ lymphocytes was also observed in the presence of HPV oncogenes, mainly with E6 and E7 in NK and TCD8+ cells. In conclusion, MDA-MB-231 breast cell lineage transfected with HPV oncogenes can downregulate the number and function of lymphocytes and monocytes.

Background: School meals represent a significant supply of nutrients for children in Brazil, especially those in conditions of social vulnerability. Objectives: This study aimed to assess the levels of arsenic (As), cadmium (Cd), and lead (Pb) in meals served in public elementary schools in four municipalities in the state of Bahia, Brazil, and assess the risk posed to children's health. Methods: Ninety-six samples were collected from 16 schools, freeze-dried, and subjected to microwave-assisted digestion. The As, Cd, and Pb levels were determined by graphite furnace atomic absorption spectrometry. The risk assessment was based on calculating each element's hazard quotient (HQ). Results: None of the samples reached or exceeded the tolerable levels for the elements analyzed. Pb was the metal that obtained the most significant result, reaching maximum levels of 39-157 µg.kg-¹. Conclusions: No element exceeded the PTWI proposed by JECFA; thus, the toxic metal content in school meals poses a negligible risk to children´s health.

Wood and plants are made of fibers which contain, in addition to cellulose, lignin and hemicelluloses. Xylan and galactoglucomannan are the dominant secondary cell wall hemicelluloses. Besides fibers’ traditional use in textile and paper industries, the fibers are important materials for the biorefinery industry and for developing biocomposites. In the former context, renewable lignocellulosic biomass is used as feedstock to sustainably produce fuels, chemicals, and polymers. On the other hand, in relation to composites, cellulose fibers which are anisotropic play an important reinforcing role in fiber-matrix interactions. However, for these and other applications, structural analysis of the fibers is important and among many analytical techniques used, Raman spectroscopy is one of the methods. However, given the structural similarity between hemicelluloses and cellulose, many of their Raman contributions overlap. While the wavenumber positions corresponding to the Raman contributions of cellulose, hemicelluloses, and lignin are known, extent to which overlapping features of hemicellulose modify the spectrum of cellulose is not yet fully understood. The present investigation focuses on this aspect by using xylan as one of the hemicelluloses. As a model system, samples with various mass ratios of microcrystalline cellulose (cotton) and xylan (birch wood) were prepared and analyzed by FT-Raman spectroscopy. The findings were then applied to interpret Raman spectra of selected xylan containing delignified plant fibers. It is hoped that insights gained would lead to better interpretation of the spectra of natural and treated plant materials.

Background: Idiopathic Toe Walking (ITW) is the persistence of a forefoot strike pattern at initial contact while walking beyond the age of three years, in the absence of other justifiable causes. This review aims to consolidate the current knowledge on the subject and to highlight recent advancements in literature. Methods: We conducted an electronic search in the following databases up to June 2023: Ovid MEDLINE, EBSCO, Embase, CINAHL Plus, and PubMed. The PICO framework was employed to define search terms. Results: Despite considerable methodological heterogeneity among studies, we found a stronger inclination toward investigating etiological and prognostic factors. There is a trend for a higher prevalence in boys with a positive family history. Novel classifications have been proposed to improve differential diagnosis. Among conservative treatment options, there is stronger evidence for gait improvement with the use of serial casting followed by orthoses. Severe cases may benefit from surgical Zone III gastrocsoleus lengthening. Conclusion: Further studies with standardized methodologies are required to clarify questions about the etiology, classification, and treatment of this condition. Nonetheless, there is a higher level of evidence supporting conservative treatments with serial casting and orthoses, as well as gastrocsoleus Zone III surgical lengthening for severe cases in the second decade of life.

Manufacturing systems need to meet I4.0 guidelines to deal with uncertainty in scenarios of turbulent demand for products. The engineering concepts to define the service’s resources to manufacture the products will be more flexible, ensuring the possibility of re-planning in operation. These can follow the engineering paradigm based on capabilities. The virtualization of industry components and assets achieves the RAMI 4.0 guidelines and (I4.0C), which describes the Asset Administration Shell (AAS). However, AAS are passive components that provide information about I4.0 assets. The proposal of specific paradigms is exposed for managing these components, as is the case of multi-agent systems (MAS) that attribute intelligence to objects. The implementation of resource coalitions with evolutionary architectures (EAS) applies cooperation and capabilities’ association. Therefore, this work focuses on designing a method for modeling the asset administration shell (AAS) as virtual elements orchestrating intelligent agents (MAS) that attribute cooperation and negotiation through contracts to coalitions based on the engineering capabilities concept. The systematic method suggested in this work is partitioned for the composition of objects, AAS elements, and activities that guarantee the relationship between entities. Finally, Production Flow Schema (PFS) refinements are applied to generate the final Petri net models (PN) and validate them with Snoopy simulations. The results achieved demonstrate the validation of the procedure, eliminating interlocking and enabling liveliness to integrate elements behavior.

Dyslipidemia presents high levels of serum cholesterol, being characterized as a risk factor for cardiovascular diseases, especially for the development of atherosclerosis. E. oleracea (OFEO), A. esculentus (OFAE), B. orellana (OFBO) and granulated (CHR) oils are rich in bioactive compounds with potential to treat changes in lipid metabolism. This study investigated the effects of treatments with oils from A. esculentus, E. oleracea, B. orellana and granules (Chronic SM®) on saturated fat-induced dyslipidemia Cocos nucifera L. The chromatographic profile showed the majority of unsaturated fatty acids in the tested oils. The quantification of tocotrienols and geranylgeraniol was obtained in OFBO and CHR. Treatments with OFEO, OFAE, OFBO and CHR were able to significantly reduce glycemia with p&gt;0.001, as well as hypertriglyceridemia, total cholesterol and LDL-cholesterol, in addition to increasing HDL-cholesterol. The treatments inhibited the formation of atheromatous plaques in the vascular endothelium of the treated rats. The obtained results suggest that the OFEO, OFAE, OFBO and CHR groups have antidyslipidemic effects and antiatherogenic activity.

The convergence of digital twin technology with additive manufacturing (AM) represents a transformative advancement in the fields of design, simulation, and production. Digital twins—virtual replicas of physical assets—enable real-time monitoring, simulation, and optimization of manufacturing processes by mirroring their physical counterparts. When integrated with additive manufacturing, which allows for the creation of complex geometries and rapid prototyping, digital twins enhance the ability to design, test, and refine products with unprecedented precision and efficiency. This integration facilitates iterative design improvements, predictive maintenance, and real-time process adjustments, leading to more accurate simulations and optimized production workflows. By leveraging data from digital twins, manufacturers can anticipate issues, reduce material waste, and shorten development cycles. This abstract explores how the fusion of digital twin technology with AM not only refines traditional manufacturing paradigms but also paves the way for more innovative and adaptive manufacturing practices.

This study focuses on the development and characterization of a series of six new dansyl derivatives (L1 to L6) and their integration into PMMA polymers for application in environmental sensing. The photophysical properties of these derivatives were extensively studied in various solvents and in solid state. A remarkable positive solvatochromic effect was observed, indicating their potential in microenvironmental polarity assessment. The dansyl derivatives demonstrated selective sensing capabilities for Cu2+ and Hg2+ metal ions, with the formation of mononuclear species. Additionally, their acid-base responsive nature was explored, revealing potential for pH-sensitive applications. The incorporation of these derivatives into PMMA polymers resulted in acid-base sensitive materials suitable for environmental monitoring, particularly in detecting hazardous gases and changes in pH levels. This integration overcomes the solubility limitations of dansyl compounds and extends their applicability in diverse sensing scenarios.

4D printing represents an innovative evolution of 3D printing technologies, incorporating time as a fourth dimension to create objects that can transform and adapt over time in response to environmental stimuli. This emerging field has shown significant advancements in materials science, design principles, and applications. Recent research focuses on developing responsive materials such as shape-memory polymers, hydrogels, and composites that can undergo controlled transformations in reaction to changes in temperature, humidity, or other external factors. The advancements in 4D printing have led to a wide array of applications, including self-healing structures, adaptive medical devices, and dynamic architectural components. This abstract examines the latest progress in 4D printing technologies, highlighting key advancements in material development and design strategies. It explores various case studies that demonstrate the practical implementation of 4D-printed objects across different sectors. Furthermore, the abstract discusses the challenges faced by researchers, including material limitations, scalability issues, and the need for standardized testing methods. The potential future directions of 4D printing are also considered, emphasizing the need for interdisciplinary collaboration to overcome current limitations and expand the range of applications. This research underscores the transformative potential of 4D printing in creating intelligent and adaptable systems, offering significant benefits across industries from healthcare to construction.

Purpose: To evaluate nursing leaders' perception towards communication and relationship management competencies while using digital platforms during the COVID-19 pandemic. Background: Communication and relationship management competencies among nursing leaders will ensure healthcare models are successfully implemented. Nursing leaders can achieve effective leadership by mastering these competencies leading to an overall improvement in the quality of nursing care. However, digital platforms have been rapidly evolving in the healthcare ecosystem and have been significant during the battle with COVID-19. It is crucial to ensure that nursing leaders can use digital platforms to communicate and practice efficient management in their op-erations, especially during a crisis when their services are vital. Design: Descriptive, comparative study. Methods: The study was conducted between February to March 2021. A 5-item Linkert-type questionnaire was adopted from the American Organization for Nursing Executives (2005) and was sent to identified nursing leaders in Hamad Medical Corporation through the official email. Results: Two hundred fifty nurse leaders were invited to participate, but only 116 responded positively, translating to a response rate of 46.4%. The male participants represented a larger proportion of 64.10%, while the female was 35.90%. Regarding the questionnaire, the Cronbach alpha was α ˃ 0.987, indicating that all items revealed a sufficient level of internal consistency. The respondents had a minimum of 0 and a maximum of 52.6n in the communication and relationship management items. Influencing behavior, relationship management, and effective communica-tion had the lowest scores, which indicate low competency. The F value in ANOVA analysis was close to 1.0, implying that the null hypothesis is true. The significance value is <0.5 implying that there is a difference in response on effective communication proficiency of nurse leaders. Conclusions: Digital platforms are communication tools that are widely adopted to engage and reach nurses on numerous topics. Nurse leaders should capitalize on their benefits and generate critical discussions. The continued need to research nursing leadership competencies is critical as healthcare continues to change and evolve. Educational institutions and healthcare organizations must understand that nursing leaders should strive for professional development and knowledge acquisition to improve their communication and management.

Here we investigate how the local properties of particles in a thermal bath may influence the thermodynamics of the bath, and consequently alter the statistical mechanics of subsystems that comprise the bath. We are guided by the theory of small-system thermodynamics, which is based on two primary postulates: that small systems can be treated self-consistently by coupling them to an ensemble of similarly small systems, and that a large ensemble of small systems forms its own thermodynamic bath. We adapt this “nanothermodynamics” to investigate how a large system may subdivide into an ensemble of smaller subsystems, causing internal heterogeneity across multiple size scales. For the semi-classical ideal gas, maximum entropy favors subdividing a large system of “atoms” into an ensemble of “regions” of variable size. The mechanism of region formation could come from quantum exchange symmetry that makes atoms in each region indistinguishable, while decoherence between regions allows atoms in separate regions to be distinguishable by their distinct locations. Combining regions reduces the total entropy, as expected when distinguishable particles become indistinguishable, and as required by a theorem in quantum mechanics for sub-additive entropy. Combining large volumes of small regions gives the usual entropy of mixing for a semi-classical ideal gas, resolving Gibbs paradox without invoking quantum symmetry for atoms that may be meters apart. Other models presented here are based on Ising-like spins, which are solved analytically in one dimension. Focusing on the bonds between the Ising-like spins we find similarity in the equilibrium properties of a two-state model in the nanocanonical ensemble and a three-state model in the canonical ensemble. Thus, emergent phenomena may alter the thermal behavior of microscopic models, and the correct ensemble is necessary for fully-accurate predictions. Another result using Ising-like spins involves simulations that include a nonlinear correction to Boltzmann’s factor, which mimics the statistics of indistinguishable states by imitating the dynamics of spin exchange on intermediate lengths. These simulations exhibit 1/f-like noise at low frequencies (f), and white noise at higher f, similar to equilibrium thermal fluctuations found in many materials.

Exacerbated inflammatory responses are a hallmark of severe coronavirus disease 2019 (COVID-19). Zileuton (Zi) is a selective inhibitor of 5-lipoxygenase, an enzyme involved in the production of several inflammatory/pro-resolving lipid mediators. Herein, we investigated the effect of Zi treatment in a severe acute respiratory syndrome (SARS) model. Mouse hepatitis virus (MHV)3-infected mice treated with Zi significantly improved the clinical score, weight loss, cardiopulmonary function, and survival rates compared with infected untreated animals. The protection observed in Zi-treated mice was associated with a lower inflammatory score, reduced dendritic cell-producing tumor necrosis factor (TNF), and increased neutrophil-producing interleukin (IL)-10 in the lungs 3 days after infection (dpi). At 5 dpi, the lungs of treated mice showed an increase in Th2-, Treg CD4+-, and Treg CD8+-producing IL-10 and reduced Th1 infiltrating cells. Furthermore, similar results were found upon Zi treatment after SARS-CoV2 infection in transgenic mice expressing the human angiotensin I-converting enzyme 2 (ACE2) receptor driven by the cytokeratin-18 (K18) gene promoter (K18-hACE2), significantly improving the clinical score, weight loss, and lung inflammatory score compared with untreated animals. Our data suggest that Zi protects against developing severe lung disease during SARS induced by betacoronavirus without affecting the host’s capacity to deal with infection.

Metal additive manufacturing (AM), commonly referred to as 3D printing with metals, is an innovative technology with significant potential to transform industries such as aerospace, automotive, and healthcare. Despite its promise, the field faces several challenges that impact both its technical feasibility and economic viability. This paper explores the primary technical challenges, including material properties and processing complexities, such as the need for precise control of thermal gradients and the mitigation of defects like porosity and residual stresses. Additionally, it addresses the economic barriers, including high initial equipment costs, the need for specialized knowledge, and the relatively slow build speeds compared to traditional manufacturing methods. By examining these challenges, this paper aims to provide a comprehensive overview of the current state of metal additive manufacturing and suggest potential pathways for overcoming these obstacles to facilitate wider adoption and technological advancement in the field.

This paper proposes a model to evaluate business projects to get into an incubator, allowing to rank them in order of selection priority. The model combines the Momentum method to build prospective scenarios and the Multiple Criteria Decision Making (MCDM) method TOPSIS-2N to rank the alternatives. Six business projects were evaluated to be incubated. The Momentum method made it possible for us to create an initial core of criteria for the evaluation of incubation projects. The TOPSIS-2N method supported the decision to choose the company to be incubated by ranking the alternatives in order of relevance. Our evaluation model has improved the existing models used by incubators. This model can be used and / or adapted by any incubator to evaluate the business projects to be incubated. The set of criteria for the evaluation of incubation projects is original and the use of prospective scenarios with a MCDM method to evaluate companies to be incubated does not exist in the literature.

Textile and clothing is one of the most important industrial sectors, not only due to the significant number of jobs generated, but also because it addresses one of the people’s fundamental needs (clothing). It is, however, a sector with a huge environmental impact, all over the world, and also an important social impact, especially in developing countries. Sustainability in the Textile &amp; Clothing value chain is a known issue, concerning both environmental, and economical-social facets of sustainability. One way to improve sustainability in this sector is by measuring the environmental, economic and social impacts of value chain activities and, ultimately, computing an Environmental and Circular score for each batch of textile and clothing product, and an Economical and Social score for each involved firm, reflected in their products. The consumer will then have the opportunity and responsibility for selecting products with the least negative environmental, economical and social impact. This article presents the results of STVgoDigital project - PPS1, developed in Portugal with the aim of implementing the traceability of textile and clothing products, boosting sustainability in this sector, and preparing the ground for the implementation of the circular economy. More exactly, a blockchain-based textile and clothing value-chain traceability platform is presented, for tracing textile product lots and activities, along the value chain, classifying them with a score, which measures their environmental and social impact. The environmental, economic and social impact scores are based on a set of proposed indicators. The results are assessed through the presentation of a case study of a face towel (home textile) and a case study of a T-shirt (clothing).

Passive microwave measurements have been available on satellites dating back to the 1970s on research satellites flown by the National Aeronautics and Space Administration (NASA). Since then, several other sensors have been flown to retrieve hydrological products for both operational weather applications (e.g., the Special Sensor Microwave/Imager–SSM/I; the Advanced Microwave Sounding Unit–AMSU) and climate applications (e.g., the Advanced Microwave Scanning Radiometer–AMSR; the Tropical Rainfall Measurement Mission Microwave Imager–TMI; the Global Precipitation Mission Microwave Imager–GMI). Here the focus is on measurements from the AMSU-A, AMSU-B and Microwave Humidity Sounder (MHS). These sensors have been in operation since 1998 with the launch of NOAA-15, and are also on board NOAA-16, -17, -18, -19 and the MetOp-A and -B satellites. A data set called the “Hydrological Bundle” is a Climate Data Record (CDR) that utilizes brightness temperatures from Fundamental CDRs to generate Thematic CDRs (TCDR). The TCDR’s include: Total Precipitable Water (TPW), Cloud Liquid Water (CLW), Sea-Ice concentration (SIC), Land surface temperature (LST), Land surface emissivity (LSE) for 23, 31, 50 GHz, rain rate (RR), snow cover (SC), ice water path (IWP), and snow water equivalent (SWE). The TCDR’s are shown to be in general good agreement with similar products from other sources such as the Global Precipitation Climatology Project (GPCP) and the Modern-Era Retrospective Analysis for Research and Applications (MERRA-2). Because of the careful intercalibration of the FCDR’s, little bias is found among the different TCDR’s produced from individual NOAA and MetOp satellites, except for normal diurnal cycle differences.

Recently, the properties of bouncing oil droplets, also known as `walkers', have attracted much attention because they are thought to offer a gateway to a better understanding of quantum behaviour. They indeed constitute a macroscopic realization of wave-particle duality, in the sense that their trajectories are guided by a self-generated surrounding wave. The aim of this paper is to try to describe walker phenomenology in terms of de Broglie-Bohm dynamics and of a stochastic version thereof. In particular, we first study how a stochastic modification of the de Broglie pilot-wave theory, à la Nelson, affects the process of relaxation to quantum equilibrium, and we prove an H-theorem for the relaxation to quantum equilibrium under Nelson-type dynamics. We then compare the onset of equilibrium in the stochastic and the de Broglie-Bohm approaches and we propose some simple experiments by which one can test the applicability of our theory to the context of bouncing oil droplets. Finally, we compare our theory to actual observations of walker behavior in a 2D harmonic potential well.

This paper reviews the ethical issues involved and argues that each of the usual policies for handling conscientious refusals faces serious challenges. Healthcare providers who refuse to provide medical services should be expected to explain their reasons, make prompt referrals, and bear some of the resulting costs or burdens.

Stagnation is the transient state of a solar thermal system under high solar irradiation where the useful solar gain is zero. Both flat-plate collectors with selective absorber coatings and vacuum-tube collectors exhibit stagnation temperatures far above the saturation temperature of the glycol-based heat carriers within the range of typical system pressures. Therefore, stagnation is always associated with vaporization and propagation of vapor into the pipes of the solar circuit. It is therefore essential to design the system in such a way that vapor never reaches components that cannot withstand high temperatures. In this article, a thermal-hydraulic model based on the integral form of a two-phase mixture model and a drift-flux correlation is presented. The model is applicable to solar thermal flat-plate collectors with meander-shaped absorber tubes and selective absorber coatings. Experimental data from stagnation experiments on two systems, which are identical except for the optical properties of the absorber coating, allowed comparison with simulations carried out under the same boundary conditions. The absorber of one system features a conventional highly selective coating, while the absorber of the other system features a thermochromic coating, which exhibits a significantly lower stagnation temperature. Comparison of simulation results and experimental data show good conformity. This model is implemented into an open-source software tool called “THD” for the thermal-hydraulic dimensioning of solar systems. The latest version of THD, updated by the results of this article, enables planners to achieve cost-optimal design of solar thermal systems and to ensure failsafe operation by predicting the steam range under the initial and boundary conditions of worst-case scenarios.

Blockchain is a data management innovation that allows the linkage of successive records regarding a digital entity, and to store them into a shared, decentralized, distributed and retroactively unchangeable data structure. Each bit of information related to the recorded events contains the public key of the owner, therefore, the whole record is formed by a chain of transactions with blocks of information identifying where the transaction was generated from and its current destination (Nakamoto, 2008). Blockchain is the technology behind Bitcoin, an online currency that was first introduced in 2009. The technology makes it possible to conduct business between members within the network without relying on third parties as guarantors to prove transaction integrity, thus increasing speed and reducing cost of transaction. Moreover, the transparency posed by the technology makes it possible to trace goods and services through all stages, making the technology a unique tool that can be assimilated by, for example, the Agro-food supply chain systems. Specifically, Blockchain is being tested in a pilot project in the UK meat (Beef) industry by the FSA (Food Standards Agency) and the slaughterhouses, with IBM Blockchain platform to ensure full transparency and compliance with regulations, (Evenstad, 2018). However, the uptake of Blockchain in the fresh produce (fresh and fresh, short-life processed fruit, vegetables, salads) supply chain is lagging, in the United Kingdom, and remains untested and limited to literature, models and specific case studies in the United States of America and France. The study aims at understanding how prepared stakeholders are in adopting Blockchain for their operations. An inductive qualitative method was employed through non-structured interviews with three companies and one consumer focus group. The interviews were guided by seven (7) open-ended questions, which were unstructured. The collected data was analyzed with axial coding through constant comparative methods. Seven (7) themes were identified as factors influencing the adoption of Blockchain in the fresh produce supply chain in the UK. These are, novelty of the technology, complexity of the fresh produce supply chain in UK, level of product transformation, technological compatibility with operations, cost and value, Customer (retailer) push for adoption, and public/consumers opinion. The adaptation of Blockchain by the current fresh produce supply chain in the UK and the EU at large will come about when concerns on Novelty, and complexity of supply chain systems are fully addressed.

Alzheimer's disease is characterized by a progressive decline of cognitive functions. The class of drugs used for the treatment are acetylcholinesterase inhibitors. Essential oils have contributed to folk medicine and discovery of new drugs for a long time. The purpose of the study was to investigate the in vitro and in silico the anti-acetylcholinesterase activity, as well as acute toxicity of the essential oil of Lippia origanoides. EOLO was obtained by hydrostelting and analyzed by gas chromatography-mass spectrometry. The inhibition assay of acetylcholinesterase enzyme activity was evaluated in vitro, as well as in silico by docking. The effects of EOLO on hematological, biochemical and behavioral parameters were analyzed in mices. We expose that EOLO shows good anti-acetylcholinesterase activity and low toxicity, possibly resulting from the action of the majority compounds thymol, carvacrol and p-cymene. The anti-acetylcholinesterase potential in vitro demonstrating a 70% inhibition. The docking results elucidated the participation of the major phenolics in AChE inhibition by interacting with the catalytic cavity of AchE. The acute oral toxicity test classified as low toxicity. These results contribute to expand the knowledge about essential oil of Lippia origanoides. Therefore, appears to be promising for herbal medicine production with anti-acetylcholinesterase and antioxidant activity.

This research presents a comprehensive bibliometric and sentiment analysis of nanocomposite literature from 1990 to 2024. Employing cutting-edge computational methods, the study delves deep into the progression of microstructural characterization, electrical properties, and mechanical behaviors of nanocomposites. The analysis utilizes advanced Boolean search strategies from the Scopus database, ensuring a thorough extraction of thematic content. The results explore various themes and insights, shedding light on trends evident in the Scopus database, particularly the prominence of research on nanocomposite microstructure, electrical attributes, and mechanical performance. The paper also offers textual analytics and bibliometric data, showcasing critical collaborative efforts and influential studies. Significant discoveries encompass the evolution of research language, shifts in thematic focus, and global contributions, providing a comprehensive perspective on the current landscape of nanocomposite research and its dynamic evolution. Moving forward, the "State-of-the-Art and Gaps Extracted from Results and Discussions" section of the paper delves into the most recent advancements in nanocomposite research. It delves into various types of nanocomposites, with a particular emphasis on their microstructural characteristics, electrical properties, mechanical dynamics, and the application of nanocomposite films. This section identifies key research themes, traces historical progress, and highlights emerging trends while underscoring the significance of collaboration and the influence of pivotal studies that have shaped the field. Lastly, in the "Literature Review Guided by Artificial Intelligence" section, the paper introduces a revised approach for researching nanocomposites through AI-guided techniques. This approach prioritizes articles published in 2023 based on citation frequency. Here, the focus is on exploring the relationship between nanocomposites and their electrical properties, emphasizing their fundamental interactions and impact on electrical characteristics. Various nanocomposite systems are covered, highlighting their composition, structure, and functionality. Findings from recent studies are integrated to provide a comprehensive overview of the current state of knowledge in this area. Notably, the sentiment analysis, anchored by an average sentiment score of 0.638771, underscores a positive trajectory in academic discourse, emphasizing the growing recognition of the potential of nanocomposites. The bibliometric exploration maps the intellectual domain, emphasizing pivotal research themes and the influence of crosslinking time on nanocomposite attributes. While this study is thorough, it acknowledges its limitations and advocates for broader database inclusion in future research endeavors. This work elucidates the prevailing trends in nanocomposite research, emphasizing the indispensable role of computational tools in comprehending this vast wealth of information.

Feline sporotrichosis is an endemic disease with high occurrence in Brazil. Itraconazole (ITZ), remains the drug of choice for treating this disease in cats, despite the increasing reports of therapeutic failure. A controlled, randomized clinical trial was performed on 166 naive cats with sporotrichosis to assess the effectiveness and safety of the combination therapy (ITZ+KI) com-pared with ITZ monotherapy. Cats were randomly allocated in two treatment groups: G1 - ITZ 100 mg/cat/day and G2 - ITZ 100mg/cat/day + KI 2.5-20 mg/kg/day. Cats treated in G2 presented 77% more risk of reaching clinical cure (a positive effect) than those treated in G1, even when controlled by negative predictors. The survival curves of the two treatment protocols indicates that clinical cure was achieved faster in G2. An increase in the KI dose was necessary in 28 cats due to persistence of clinical signs. Adverse reactions were equally frequent in both groups and manageable with a temporary drug suspension and/or a hepatoprotective therapy. The combination therapy was associated with a higher cure rate and a shorter treatment time, suggesting that ITZ+KI arises as a better option for treating feline sporotrichosis and should be considered as the first-line treatment in the presence of negative predictors.

Eutrophication, a global concern, impacts water quality, ecosystems, and human health. It’s crucial to monitor algal blooms in freshwater reservoirs, as they indicate the trophic condition of a waterbody through Chlorophyll-a (Chla) concentration. Traditional monitoring methods, however, are expen-sive and time-consuming. Addressing this hindrance, we developed models using remotely sensed data from the Sentinel-2 satellite for large-scale coverage, including its bands and spectral indexes, to estimate the Chla concentration on 149 freshwater reservoirs in Ceará, Brazil. Several machine learning models were trained and tested, including k-nearest neighbours, random forests, extreme gradient boosting, the least absolute shrinkage, group method of data handling (GMDH), and sup-port vector machine models. A stepwise approach determined the best subset of input parameters. Using a 70/30 split for the training and testing datasets, the best-performing model was the GMDH, achieving an R2 of 0.91, MAPE of 102.34%, and RMSE of 20.38 g/L, which are values consistent with the ones found in the literature. Nevertheless, the predicted Chla concentration values were most sensitive to the red, green, and near infra-red bands.

The objective of this work was to evaluate the blending and grinding influence over the nutritional, sensorial and sustainable aspects of coffee. To do so, a systematic review of the literature was accomplished. The database for the selection of relevant papers was the Portal de Periódicos da Capes, with remote access via CAFe. For the elaboration of the research, a chronological criterion with period restriction was used, considering the period between 2008-2022, to access all possible works related to the theme of this work. The following terms were used: blending; grinding; coffee; nutrition-al; sensorial; sustainability. To filter the searches, the association of these terms was also used by means of links and word associations. In the terminology, the Boolean operator AND was used to interconnect the terms used. Roasting degree, grinding, and amount of each coffee species impacts the nutritional and sensorial aspects of coffee. And the determination of each blending influences the sustainability of the environment, economic and social aspects of the coffee chain.

O26 enteropathogenic Escherichia coli (EPEC), possesses a unique pseudocapsule composed of polysaccharides identical to the O antigen in their lipopolysaccharide (LPS) membrane. Therefore, the impact of O26 polysaccharides on the immune evasion mechanisms of capsulated O26 EPEC was investigated. Our findings reveal that the concentration of GlcNAc, an immunodominant unit of O26 polysaccharides capable of activating the MBL (Mannose Biding Lecting) pathway of the complement system, was found to be lower in capsulated EPEC O26 compared to naked shiga toxin-producing E. coli (STEC) O26 strain. It was noted that, unlike the naked STEC strain, the capsulated EPEC O26 strain was protected against lysis by the alternative pathway of the com-plement system by inhibiting C3b adhesion to its bacterial surface. Capsulated EPEC O26 strains were also able to avoid phagocytosis by macrophages. However, the immune evasion provided by the capsule was overcome in the presence of anti-O26 polysaccharide antibodies. Additionally, these antibodies were able to recognize O26 EPEC in the presence of biofilm and inhibit their adhesion to human epithelial cells. Overall, the results indicate that the O26 polysaccharides can generate an effective humoral immune response, making them promising antigens for the de-velopment of a vaccine against capsulated O26 E. coli

The COVID-19 pandemic initiated a race to determine the best measures to control the disease and to save as many people as possible. Efforts to implement social distancing, the use of masks, and massive vaccination programs turned out to be essential in reducing the devastating effects of the pandemic. Nevertheless, the high mutation rates of SARS-CoV-2 challenge the vaccination strategy and maintain the threat of new outbreaks due to the risk of infection surges and even lethal variations able to resist the effects of vaccines and upset the balance. Most of the new therapies tested against SARS-CoV-2 came from already available formulations developed to treat other diseases, so they were not specifically developed for SARS-CoV-2. In parallel, the knowledge produced regarding the molecular mechanisms involved in this disease was vast due to massive efforts worldwide. Taking advantage of such a vast molecular understanding of virus genomes and disease mechanisms, a targeted molecular therapy based on siRNA specifically developed to reach exclusive SARS-CoV-2 genomic sequences was tested in a non-transformed human cell model. Since coronavirus can escape from siRNA by producing siRNA inhibitors, a complex strategy to simultaneously strike both the viral infectious mechanism and the capability of evading siRNA therapy was developed. The combined administration of the chosen produced siRNA proved to be highly effective in successfully reducing viral load and keeping virus replication under control, even after many days of treatment, unlike the combinations of siRNAs lacking this anti-anti-siRNA capability. Additionally, the developed therapy did not harm the normal cells, which was demonstrated because, instead of testing the siRNA in nonhuman cells or in transformed human cells, a non-transformed human thyroid cell was specifically chosen for the experiment. The proposed siRNA combination deeply reduced the viral load throughout the experiment and allowed cellular recovery, thus representing a potential innovation, to be considered as an additional weapon for therapy of COVID-19 and even other infectious diseases.

Umbu is a tropical fruit with high content of bioactive compounds. However, maturation causes significant losses on nutrient density reducing the nutritional value of this highly appreciated fruit. Thus, the objective of the present work was to encapsulate the Umbu fruit bioactive compounds using spray drying and identify the variables affecting the biomolecules preservation. A Box-Behnken experimental design with 3 factors was set varying inlet temperature, atomization flow rate, and maltodextrin concentration for process otimization. Then the powder physicochemical and chemical properties were characterized, and results were modeled using a polynomial equation. Results revealed that the droplet size and maltodextrin concentration had a significant influence on the conservation of the biomolecules. Drying kinetics favoring fast formation of a particle crust increases encapsulation efficiency. Bioactive compounds retention was achieved by increasing maltodextrin even at high temperatures, where a matrix is formed hindering chemical degradation. Process optimization was validated and revealed low inlet temperatures (122ºC), high atomization flow rate (5kg/h) and high maltodextrin concentration (20%) to be the most desirable conditions for bioactive compounds retention.

New advances in creating effective and affordable copper-based catalysts for water splitting represent a promising strategy for driving sustainable energy technologies. However, ma- terials containing copper are susceptible to corrosion and agglomeration. In this study, we describe a synthesis route to produce olamine-functionalized CuO nanoparticles using the Hot Injection method. Nanoparticles were obtained and subsequently deposited on FTO substrates, undergoing thermal treatment at 500°C and 600°C in atmospheres containing O2 and N2, aiming to enhance the adhesion of the active material to the substrate and modify its oxidation state. Microstructural properties were analyzed using XRD, SEM, and TEM, while electrochemical properties were studied using CV, LSV, and EIS. Electrodes treated thermally in an N2 atmosphere at 600°C exhibited higher ESCA, indicating a greater area of active sites exposed to surface reactions and, therefore, superior catalytic activity in Hy- drogen Evolution Reaction (HER). These findings show an interesting strategy for avoiding rapid electron-hole recombination and, consequently, CuO corrosion. For Oxygen Evolution Reaction (OER), samples treated thermally in O2 atmosphere at 500°C and 600°C appear to be more effective.

Background: Histoplasmosis is a systemic mycosis, present globally. We aimed to describe cases of histoplasmosis (Hc) and to establish a risk profile associated to Hc in HIV-infected patients (HIV+). Methods: This was a retrospective study of patients with a clinical-. laboratorial diagnosis of Hc. Data was fed into REDCap and statistical analysis was done with R . Results: We included 99 records, 65 HIV+ and 34 HIV-. Average age was 39 years. Median time from onset to diagnosis was 8 weeks in HIV- and 22 weeks in HIV+. Disseminated histoplasmosis occurred in 79.4% HIV+, vs 36.4% HIV-. Median CD4 count was 70. Co-infection with tuberculosis was present in 20% of HIV+. Blood cultures were positive in 32.3% of HIV+ vs 11.8% of HIV- (p=0.025); bone marrow culture was positive in 36.9% vs 8.8%(p=0.003). Most HIV+ patients (71.4%) were hospitalized. On univariate analysis, anemia, leukopenia, intensive care, use of vasopressors and mechanical ventilation were associated with death in HIV+. Conclusions: Most of our patients with histoplasmosis were HIV+, presenting advanced AIDS. Diagnosis was late in HIV+ patients, and they frequently presented disseminated Hc, required hospitalization, and died. Early screening for Hc in HIV+ and drug induced immunosuppressed patients is crucial.

Agroforestry homegardens are integrated arrangements of common vegetable plants in areas close to residences, which follow a structure similar to that of tropical forests, with the cultivation of multiple species to meet the basic needs of families, such as the provision of food and medicine, as well as ensuring an environment for other family activities. Considering the importance of these environments, this work aimed to address the composition and use of plant species in agroforestry homegardens, in order to support society initiatives and government policies to strengthen the management of natural resources and individual and collective well-being in the region. For this, 119 homegardens were studied in the municipalities of Belterra, Mojuí dos Campos and Santarém, in the state of Pará, in the Brazilian Amazonia, comprising five different zones (peri-urban, urban, floodplain, indigenous land and tourist land), obtaining the data via questionnaires and guided visitation by the residents. A total of 5,323 vegetal individual plants were surveyed, distributed in 188 species and 62 botanical families. The data showed that 80.5% of the individual plants are concentrated in 18.6% of the species, with no significant difference in the average of species per homegarden in the five zones. The predominance of species for food use, primarily fruit-bearing, stands out, showing a possible direction for incentive actions and/or for the ordering of public policies and programs aimed at these spaces. Most homegardens have up to 17 plant species; less than half of homegardens have species intended for medicinal use; and there is percentage parity between native plant species and those of exotic origin, where native plants stand out for shading. Agroforestry homegardens play a crucial role in the conservation and cultivation of species for food purposes, with the cultivation or maintenance of plants based on their various purposes, showing distinct profiles of distribution and choice of species, evidencing their socioeconomic and environmental importance. Thus, it is important that these land use systems are valued, investing financial resources in actions and projects aimed at maintaining and enhancing their benefits for the region.

New proposals for the equation of state of four- and five-dimensional hard-hypersphere mixtures in terms of the equation of state of the corresponding monocomponent hard-hypersphere fluid are introduced. Such proposals (which are constructed in such a way so as to yield the exact third virial coefficient) extend, on the one hand, recent similar formulations for hard-disk and (three-dimensional) hard-sphere mixtures and, on the other hand, two of our previous proposals also linking the mixture equation of state and the one of the monocomponent fluid but unable to reproduce the exact third virial coefficient. The old and new proposals are tested by comparison with published molecular dynamics and Monte Carlo simulation results and their relative merit is evaluated.

Sustainability in Additive Manufacturing (AM) is an emerging area of research that examines the environmental impacts and potential benefits of AM processes compared to traditional manufacturing methods. This paper analyzes the environmental footprint of additive manufacturing technologies, including material usage, energy consumption, and waste production. AM techniques, such as fused deposition modeling (FDM), stereolithography (SLA), and selective laser sintering (SLS), are evaluated for their efficiency and sustainability. Key factors such as resource utilization, lifecycle emissions, and recyclability are assessed to determine how AM can contribute to a more sustainable manufacturing paradigm. The study highlights that while AM offers advantages such as reduced material waste and the potential for localized production, it also poses challenges, including high energy consumption and limited material options. The paper concludes with recommendations for improving the environmental performance of AM, including advancements in material science, energy-efficient technologies, and the integration of circular economy principles. By addressing these aspects, AM can play a significant role in achieving sustainability goals in manufacturing.

This review aimed to analyze the effects of additives in the process of producing silage from re-hydrated corn grains for ruminants. Control treatment studies used in this analysis was corn grain rehydrated with water only. To be included in the review, the studies needed to follow stand-ardized criteria, including the absence of additives in the control treatment and the evaluation of the silage in beef animals, such as cattle, goats, and sheep. A total of seven publications, published between 2014 and 2022, were included in the final dataset. To compare the results, the PROC ANOVA of SAS was used, which included a random effect of comparison within the study, per-forming a paired comparison. It was observed that the use of additives did not influence the chemical composition, pH, organic acid and ethanol content, microbial population, fermentative losses, aerobic stability, and dry matter in vitro digestibility of rehydrated corn grain silage (p >0.05). Based on this information, it is concluded that the use of additives in rehydrated corn grain silage did not show major differences on silage quality. It is important, however, to evaluate the effects of additives in silages on animal performance.

Human bocavirus (HBoV) is an emerging virus that has been detected worldwide that could be associated with cases of acute gastroenteritis (AGE). However, its contribution to AGE has not been elucidated. This study aimed to describe the frequency, clinical features, and HBoV genotypes circulation in children up to 5 years with or without AGE symptoms in Acre, Northern Brazil. A total of 480 stool samples were collected between January and December 2012. Fecal samples were used for extraction, nested PCR amplification, and sequencing for genotyping. Statistical analysis was applied to verify the association between epidemiological and clinical characteristics. Overall HBoV-positivity was 10% (48/480), being HBoV-positivity rates of 8.4% (19/226) and 11.4% (29/254) recorded among diarrheic and non-diarrheic children, respectively. The most affected age group was between 7 and 24 months (50%). HBoV infection was more frequent in children living in urban areas (85.4%), using water from the public network (56.2%), and living with adequate sewage facilities (50%). Co-infection with other enteric viruses was 16.7% (8/48) and the most prevalent coinfection was RVA+ HBoV (50%, 4/8). HBoV‐1 was the most frequent species detected, responsible for 43.8% (21/48) of cases, followed by HBoV-3 (29.2%, 14/48) and HBoV-2 (25%, 12/48). In the present study, HBoV infections are not associated with AGE, as most HBoV cases belonged to the non-diarrheal group without AGE symptoms. Future studies are warranted to determine the role of HBoV in causing acute diarrhea disease.

Additive manufacturing (AM), commonly known as 3D printing, has revolutionized the production of complex geometries that were once challenging or impossible to achieve through traditional manufacturing techniques. This paper investigates the capabilities of additive manufacturing in producing intricate designs, focusing on the unique advantages and potential applications across various industries. Additive manufacturing enables the creation of complex geometries by adding material layer by layer, allowing for greater design freedom and the ability to produce structures with intricate internal features, complex curves, and lightweight lattice structures. This capability is particularly advantageous in fields such as aerospace, biomedical, and automotive, where weight reduction, customization, and the integration of complex internal channels are critical. The study explores various additive manufacturing technologies, including stereolithography (SLA), selective laser sintering (SLS), and fused deposition modeling (FDM), highlighting their specific strengths and limitations in producing complex geometries. Factors such as material properties, resolution, surface finish, and build size are analyzed to determine the suitability of different AM processes for specific applications. Additionally, the research delves into the design considerations and software tools that facilitate the creation of complex geometries in AM, including generative design and topology optimization. These tools leverage the design freedom offered by AM to optimize structures for weight, strength, and functionality, pushing the boundaries of what is possible in product design. The paper concludes with an examination of the challenges and future directions in the field, such as improving material properties, reducing production costs, and enhancing the accuracy and reliability of AM processes. The potential of additive manufacturing to revolutionize the production of complex geometries is underscored, emphasizing its growing importance in modern manufacturing and its role in enabling innovative solutions across various industries. This abstract provides an overview of the potential and challenges of additive manufacturing for producing complex geometries, suitable for an academic paper or report. If you need more specific information or have a different focus, feel free to ask!

Additive Manufacturing (AM), commonly known as 3D printing, has revolutionized various industries, including the medical field. This technology enables the creation of complex structures layer by layer, offering unprecedented customization and precision. In medical applications, AM has proven transformative in producing patient-specific implants, prosthetics, and anatomical models, facilitating better surgical planning and outcomes. Additionally, it has shown promise in bioprinting, where cells and biomaterials are used to create tissue-like structures for regenerative medicine. The ability to rapidly prototype and manufacture medical devices reduces time and costs, and enhances personalized patient care. This abstract explores the diverse applications, benefits, and challenges of AM in the medical sector, highlighting its potential to revolutionize healthcare and improve patient outcomes.

The field of polymer additive manufacturing (AM) has experienced rapid evolution, marked by significant advancements in materials science and technology. This paper reviews recent innovations in polymer materials tailored for additive manufacturing processes, focusing on enhancements in mechanical properties, functionalization, and processability. Key developments include the introduction of high-performance thermoplastics, composite materials incorporating fibers or nanoparticles, and novel photocurable resins. These materials offer improved strength, durability, and versatility compared to traditional polymers. Furthermore, research into bio-based and recyclable polymers highlights a growing trend towards sustainable manufacturing practices. Advances in material formulations, including self-healing and shape-memory polymers, are also examined for their potential to transform applications across various industries. This review synthesizes current research trends and provides a comprehensive overview of the state-of-the-art in polymer AM materials, emphasizing the impact of these innovations on the future of manufacturing technologies.

Additive manufacturing (AM), commonly known as 3D printing, has emerged as a transformative technology in supply chain management (SCM). This abstract explores how AM influences various aspects of SCM, including inventory management, production processes, and logistics. By enabling on-demand production and reducing reliance on traditional manufacturing methods, AM minimizes inventory costs and enhances customization capabilities. It also facilitates localized production, which can reduce lead times and transportation costs. The integration of AM into SCM fosters greater flexibility and resilience, allowing businesses to respond more swiftly to market changes and disruptions. This study highlights both the opportunities and challenges associated with adopting AM, emphasizing the need for strategic adjustments to fully leverage its potential in modern supply chains.

The integration of additive manufacturing (AM), commonly known as 3D printing, has revolutionized aerospace engineering by enabling the creation of complex, lightweight, and high-performance components. This paper explores the transformative impact of AM technologies on the design, production, and maintenance of aerospace systems. The aerospace industry demands high precision, reduced weight, and enhanced performance, all of which are facilitated by AM's ability to produce intricate geometries and optimize material usage. Key applications of AM in aerospace include the fabrication of engine components, structural parts, and customized tooling. The technology's capability to produce parts with complex internal structures, such as lattice designs, leads to significant weight reductions without compromising strength and durability. Furthermore, AM allows for rapid prototyping, enabling faster iteration and development cycles, which is crucial in the highly competitive aerospace sector.

The advancement of high-temperature structural materials is crucial for the efficiency and performance of modern gas turbines, which are widely used in aviation and power generation. This paper explores the development and optimization of materials capable of withstanding extreme temperatures, mechanical stresses, and corrosive environments within turbine engines. The focus is on nickel-based superalloys, ceramic matrix composites (CMCs), and emerging materials such as high entropy alloys (HEAs) and refractory metals. Nickel-based superalloys are the current standard due to their excellent high-temperature strength and creep resistance, while CMCs offer potential for weight reduction and improved thermal efficiency. High entropy alloys, characterized by their unique multi-component systems, present promising properties including high strength and oxidation resistance at elevated temperatures. Additionally, advances in coating technologies and additive manufacturing are enhancing the durability and performance of these materials. The paper also discusses the challenges associated with material development, including the trade-off between strength and ductility, manufacturing complexities, and the need for long-term performance data. Future research directions are identified, focusing on the integration of computational materials science and advanced characterization techniques to accelerate the discovery and implementation of next-generation high-temperature materials. The successful development of these materials is essential for improving the efficiency and reducing the environmental impact of gas turbines.

Obesity is a troubling public health problem worldwide as it increases risks of respiratory complications, systemic arterial hypertension, type 2 diabetes mellitus, sleep disorders, cardiovascular diseases, and metabolic syndrome (MetS). As a measure to counteract comorbidities associated with severe obesity, bariatric surgery stands out. This study aimed to investigate the adiponectin/leptin ratio in women with severe obesity with and without MetS undergone Roux-en-Y Gastric Bypass (RYGB) and to characterize the biochemical, glucose, and inflammatory parameters of blood in women with severe obesity before and after RYGB. Were enrolled female with severe obesity undergoing RYGP with MetS (n=11) and without (n=39). Anthropometric data and blood samples were obtained before and 6 months after RYGB to analyze total cholesterol, low-density lipoprotein (LDL), high- density lipoprotein (HDL), non-HDL total cholesterol, and glucose; and circulating levels of adiponectin and leptin. Significant reductions in weight, body mass index, and glucose, total cholesterol, LDL, and leptin were observed after surgery, with higher levels of HDL, adiponectin, and adiponectin/leptin ratio observed after surgery compared to preoperative values. This study demonstrated that weight loss induced by RYGB in patients with severe obesity with or without MetS improved biochemical and systemic inflammatory parameters, particularly the adiponectin/leptin ratio.

The complete regression of clear cell renal cell carcinoma (ccRCC) obtained pre-clinically with anti-carbonic anhydrase IX (CAIX) G36 chimeric antigen receptor (CAR) T cells in doses equivalent to 10e8 CAR T cells/ Kg renewed the potential of this target to treat ccRCC and other tumors in hypoxia. The immune checkpoint blockade (ICB) brought durable clinical responses in advanced ccRCC and other tumors. Here we tested CD8/4-1BB compared to CD28-based anti-CAIX CAR PBMCs cells-releasing anti-programmed cell death ligand-1 (PD-L1) IgG4 for human ccRCC treatment in vitro and in an orthotopic NSG mice model in vivo. Using a 10e7 CAR PBMCs cells/ Kg dose, anti-CAIX CD28 CAR T cells releasing anti-PD-L1 IgG highly decrease both tumor volume and weight in vivo, avoiding the occurrence of metastasis. This antitumoral superiority of CD28-based CAR PBMCs cells compared to 4-1BB occurred under ICB via PD-L1. Furthermore, T cell exhaustion status in peripheral CD4 T cells, additionally to CD8 was critical for CAR T cells efficiency. The lack of hepatotoxicity and nephrotoxicity upon administration of 10e7 CAR PMBCs cells/Kg dose is the basis for carrying out clinical trials using anti-CAIX CD28 CAR PBMCs cells releasing anti-PD-L1 antibodies or anti-CAIX 4-1BB CAR T cells, offering exciting new prospects for the treatment of refractory ccRCC and hypoxic tumors.

Angiotensin II (Ang II) plays a role in several inflammatory diseases and is capable of inducing the release of inflammatory mediators in several cell types. The objective was to investigate the potential of Ang II to induce mRNA expression of inflammatory mediators by cultured primary human periodontal cells. A synergistic effect of a co-treatment with Ang II and IL1β on mRNA expression of inflammatory mediators was also explored. Primary cultures of human fibroblast-like cells isolated from gingival and periodontal ligament tissues from 3 subjects were established using explant techniques. Immunophenotyping of STRO-1, Ang II type 1 receptor (AT1R) and Ang II type 2 receptor (AT2R) was performed by flow cytometry analysis. Cell cultures were challenged with Ang II (1M) for 3, 6 and 24h with or without a co-treatment with IL1β (0.1ng/mL) for 24h. mRNA expression of inflammatory mediators was performed by real time quantitative polymerase chain reaction (RT-qPCR). We present, for the first time, a precise quantification for AT1R and AT2R on human gingival and periodontal fibroblast-like cell types; the percentage of positive immunostaining compared to the total population of cells varied from 3.35% through 5.29% for AT1R and 2.97% through 4.57% for AT2R. Ang II slightly upregulated mRNA expression of IL6 and CCL2/MCP1 in gingival cells and IL8 and PTGS2/COX2 in periodontal ligament cells. IL1β induced upregulation of IL8, IL6 CCL2/MCP1, PTGS2/COX2 and IL1β mRNA in both cell types. Co-treatment with Ang II and IL1β did not show a synergistic effect under these experimental conditions. Ang II shows a low potential to induce mRNA upregulation of inflammatory mediators in cultured primary human gingival and periodontal ligament cells, most likely due to the low percentage of Ang II receptors in such cells, and no synergistic effect with the co-treatment with IL1β.

Angiotensin II (Ang II) plays a role in several inflammatory diseases and is capable of inducing the release of inflammatory mediators in several cell types. The objective was to investigate the potential of Ang II to induce mRNA expression of inflammatory mediators by cultured primary human periodontal cells. A synergistic effect of a co-treatment with Ang II and IL1β on mRNA expression of inflammatory mediators was also explored. Primary cultures of human fibroblast-like cells isolated from gingival and periodontal ligament tissues from 3 subjects were established using explant techniques. Immunophenotyping of STRO-1, AT1 and AT2 receptors was performed by flow cytometry analysis. Cell cultures were challenged with Ang II (1M) for 3, 6 and 24h with or without a co-treatment with IL1β (0.1ng/mL) for 24h. mRNA expression of inflammatory mediators was performed by real time quantitative polymerase chain reaction (RT-qPCR). We present, for the first time, a precise quantification for AT1 and AT2 receptors on human gingival and periodontal fibroblast-like cell types; the percentage of positive immunostaining compared to the total population of cells varied from 3.35% through 5.29% for AT1 and 2.97% through 4.57% for AT2. Ang II slightly upregulated mRNA expression of IL6 and CCL2/MCP1 in gingival cells and IL8 and PTGS2/COX2 in periodontal ligament cells. IL1β induced upregulation of IL8, IL6 CCL2/MCP1, PTGS2/COX2 and IL1β mRNA in both cell types. Co-treatment with Ang II and IL1β did not show a synergistic effect under these experimental conditions. Ang II shows a low potential to induce mRNA upregulation of inflammatory mediators in cultured primary human gingival and periodontal ligament cells, most likely due to the low percentage of Ang II receptors in such cells, and no synergistic effect with the co-treatment with IL1β.

CETP activity reduces plasma HDL-cholesterol concentrations, a correlate of increased risk of atherosclerotic events. However, our recent findings suggest that CETP expression in macrophages promotes an intracellular antioxidant state, reduces free cholesterol accumulation and phagocytosis, and attenuates pro-inflammatory gene expression. To determine whether CETP expression in macrophages affects atherosclerosis development, we transplanted bone marrow from transgenic mice expressing simian CETP or non-expressing littermates into hypercholesterolemic LDL receptor deficient mice. CETP expression did not change lipid-stained lesion areas but decreased macrophage content (CD68), neutrophil accumulation (LY6G) and aorta content of young male transplanted mice and decreased LY6G, TNF-α, iNOS and nitrotyrosine (3-NT) in aged female transplanted mice. These findings suggest that CETP expression in bone marrow-derived cells reduces inflammatory features of atherosclerosis. These novel mechanistic observations may help explain the failure of CETP inhibitors to reduce atherosclerotic events in humans.

The Zika virus (ZIKV) epidemic brought new discoveries regarding arboviruses, especially flaviviruses, as ZIKV was described as sexually and vertically transmitted. The latter shows severe consequences for the embryo/fetus, such as congenital microcephaly and deficiency of the neural system, currently known as Congenital ZIKV Syndrome (CZS). To better understand ZIKV dynamics in trophoblastic cells present in the first trimester of pregnancy (BeWo, HTR-8, and control cell HuH-7), an experiment of viral kinetics was performed for African MR766 low passage and Asian-Brazilian IEC ZIKV lineages. The results were described independently, and demonstrated that the three placental cells lines are permissive and susceptible to ZIKV. We noticed cytopathic effects that are typical in vitro viral infection in BeWo and HTR-8. Regarding kinetics, MR766lp showed peaks of viral loads in 24 and 48 hpi for all cell types tested, as well as marked cells death after peak production. On the other hand, HTR-8 lineage inoculated with ZIKV-IEC exhibited increased viral production in 144 hpi, with a peak between 24 and 96 hpi. Furthermore, IEC had peak variations of viral production for BeWo in 144 hpi. Both cells types continued alive during the process of viral replication. Considering such in vitro results, the hypothesis that maternal-fetal transmission is probably a way of virus transmission between the mother and the embryo/fetus is maintained.

A new method for wide-area urban roof assessment of suitability for solar photovoltaics is introduced and validated. Knowledge of roof geometry and physical features is essential for evaluation of the impact of multiple rooftop solar photovoltaic (PV) system installations on local electricity networks. This paper begins by reviewing and testing a range of existing techniques for identifying roof characteristics. It was found that no current method is capable of delivering accurate results with publicly available input data. Hence a different approach is developed, based on slope and aspect using LIDAR data, building footprint data, GIS tools and aerial photographs. It assesses each roof’s suitability for PV installation. That is, its properties should allow the installation of at least a minimum size photovoltaic system. In this way the minimum potential solar yield for region or city may be obtained. The accuracy of the new method is then established, by ground-truthing against a database of 886 household systems. This is the largest validation of a rooftop assessment method to date. The method is flexible with few prior assumptions. It is based on separate consideration of buildings and can therefore generate data for various PV scenarios and future analyses.

Genomic surveillance represents an important strategy for understanding evolutionary mechanisms, transmission profile, and infectivity of different SARS-CoV-2 variants. We assessed the epidemiological profile of 366 individuals who tested positive for SARS-CoV-2 from 29 municipalities in Rondônia between December 2021 to March 2022. Samples were collected, RNA was ex-tracted and screened using RT-qPCR for Alpha, Beta, Gamma, Delta and Omicron VOCs and viral quantification was performed. Sequences were analyzed for phylogeny, mutations and lineages. Of the samples analyzed, 93.71% were positive for the Omicron variant and 6.28% were positive for the Delta variant. The symptoms observed were cough, sore throat, and fever, with a mean duration of 5 days; no hospitalizations or deaths were reported. We noted that among the positive individuals, 51% had been immunized with two doses, 22% received three doses, 13% received one dose, and 13% were not immunized. Just 242 samples were amenable to analysis for alignment and phylogenetic characterization; corresponding to variants BA.1 and BA.1.1; a total of 120 mutations were identified, 36% of which were found in the S gene. In conclusion, there was a high frequency of mutations in the SARS-CoV-2 genome, but no record of clinical severity, demonstrating the positive effect of vaccination.

Hybrid biomaterials were engineered using the electrospinning technique, incorporating the dipeptide Boc-L-phenylalanyl-L-Isoleucine into microfibers composed of biocompatible polymers. The examination by scanning electron microscopy affirmed the morphology of the microfibers, exhibiting diameters ranging between 0.9 to 1.8 µm. The dipeptide self-assemblies into spheres with a hydrodynamic size between 0.18 to 1.26 µm. The dielectric properties of these microfibers were characterized through impedance spectroscopy, where variations in both temperature and frequency were systematically studied. The investigation revealed a noteworthy rise in the dielectric constant and AC electric conductivity with increasing temperature, attributable to augmented charge mobility within the material. The successful integration of the dipeptide was substantiated through the observation of Maxwell-Wagner interfacial polarization, affirming the uniform dispersion within the microfibers. In-depth insights into electric permittivity and activation energies were garnered using the Havriliak-Negami model and the AC conductivity behavior. Very importantly, these engineered fibers exhibited pronounced pyroelectric and piezoelectric responses, with Boc-Phe-Ile@PLLA microfibers standing out with the highest piezoelectric coefficient, calculated to be 56 pC/N. These discoveries help us understand how dipeptide nanostructures embedded into electrospun nano/microfibers can greatly affect their pyroelectric and piezoelectric properties. They also point out that polymer fibers could be used as highly efficient piezoelectric energy harvesters, with promising applications in portable and wearable devices.

Staphylococcus aureus is a gram-negative bacterium that causes superficial and deep infections that can be mild or potentially fatal. Recently, the bacterium has gained significant attention due to the increased incidence of multidrug-resistant (MDR) strains that make treatment with antibiotics dif-ficult. Owing to the MDR strains, alternative therapies such as antimicrobial photodynamic therapy (PDT) have emerged as good options to treat non-systemic infections. PDT combines a photosensi-tiser (PS) with light and oxygen to generate free radicals that destroy bacterial structures such as the plasma membrane, matrix, and genetic material. This systematic review aimed to identify the ef-fectiveness of PDT delivered using different types of hydrogels for treating wounds, burns, and contamination by S. aureus. This systematic review followed the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) 2020 guidelines. Bibliographic research was conducted using the PubMed, Web of Science, and Scopus databases. Only full articles published in English between 2013 and 2024 from any country of origin (without restrictions) were included. The research was carried out from 15 June 2023 to 15 June 2024 and did not use any automatic biblio-graphic search tool. The articles collected were identified using keywords and selected using in-clusion and exclusion criteria in accordance with the PRISMA protocol. Seven articles were in-cluded that presented a good set of evidence associated with the use of PDT against S. aureus in in vitro and in vivo studies. To conclude, PDT can effectively complement antimicrobial therapy against S. aureus, in the healing of wounds and burns. The effectiveness of this technique depends on the PS used, hydrogel type, and lesion location. Some studies have already demonstrated the ef-fectiveness of PDT but most were in vitro and a few in vivo. Further studies are required to demonstrate the safety and efficacy of PDT delivered via hydrogels in in vivo models of bacterial infection.

This study aimed to identify the most relevant factors of absenteeism in the perception of nursing technicians from a regional reference hospital in Brazil. A cross-sectional study, based on a case study, was conducted from August 2018 to July 2021, with 324 nursing technicians from a Brazilian macroregional reference hospital in Northwestern Ceará. Data were collected through Google Forms® via the Scale of Factors of Work Absenteeism (EFAL). For data analysis, the overall mean and means of the four EFAL factors were calculated. The individuals were grouped by rating level and data were presented descriptively. The results showed that fatigue, low pay, work overload, need to resolve unpostponable personal/family bureaucratic matters, and need for time to continue/post-graduate education were the main causes of absenteeism. In general, nursing technicians' perceptions varied between low and medium relevance to the factors that contributed to work absenteeism. We can associate these results to the low frequency of absen-teeism among the professionals of the institution.

Purpose: This integrated review aims to identify and analyze the multifactorial contributors to the longevity of direct restorations, focusing on tooth-, patient-, and dentist-related factors. Materials and Methods: A literature search was performed using an electronic database, PubMed/Medline, Web of Science, and Scopus, between 1980 and 2024. Titles and abstracts of papers that evaluated aspects categorized into tooth-related, patient-related, and dentist-related factors influencing restoration failure were selected and screened. Full-text assessments were conducted, and the extracted data were compiled, summarized, and synthesized. The reference lists of the collected papers were also screened, and relevant citations were included in this review. Data were gathered from clinical and laboratorial studies, systematic reviews, and meta-analyses to provide a comprehensive understanding of restoration longevity. Results: Among the tooth-related factors, multiple-surface restorations, deep margins, tooth location, and tooth vitality significantly impact restoration survival. Patient-related factors such as medical conditions, risk predictors of caries, age, sex, parafunctional habits, smoking, periodontal health, number of restorations, and socioeconomic status all play crucial roles. Regarding dentist-related factors, the decision-making process, age, experience, and dentist manual dexterity are vital aspects. Furthermore, the technique used, including isolation methods for moisture control, as well as the type of dental practice (large group vs. small practice), notably influenced the restoration survival. Conclusions: The longevity of dental restorations is influenced by a complex interplay of tooth-related, patient-related, and dentist-related factors. Strategies to improve restoration outcomes should consider all these multifactorial contributors. Continuing professional education, diligent patient guidance on the factors that influence restoration survival, careful material selection and restorative technique, and tailored individual treatment are crucial factors to reduce failure rates and improve the lifespan of restorations.

Tomato (Solanum lycopersicum L.) is a valuable horticultural crop grown and consumed worldwide. Optimum production is hindered by several factors of which Verticillium dahliae, the cause of Verticillium wilt, is one of the major biological constraints in temperate production regions. V. dahliae is difficult to manage because it is a vascular pathogen, has a broad host range and worldwide distribution, and can persist in soil for years. Understanding the pathogen virulence and genetic diversity, host resistance, and plant-pathogen interactions can ultimately inform the development of integrated strategies to manage the disease. In recent years, considerable research has focused on providing new insight into these processes as well as the development and integration of environment-friendly management approaches. In this review, we discuss and summarize the recent findings on the race and population structure of V. dahliae; pathogenicity factors; host genes, proteins, and enzymes involved in defense; the emergent management strategies, and recent approaches to managing Verticillium wilt in tomatoes.