This study compares the action of different handpieces (turbine, high-speed electric handpiece and piezoelectric device) on surface roughness of enamel and dentin when using diamond-coated working tips and burs of the same grit size. Experiment was conducted on 15 extracted first molars from patients aged 45 to 60 years. The occlusal portion was removed using a diamond-coated water wheel and then refined with a 120-130 μm grit bur in order to obtain a flat surface with an adequate exposition of the dentin core. Each surface was divided into three portions and every portion was finished with one of the three tested instruments. Rotary burs and piezoelectric tips had the same grit size (60 μm) and load on handpiece during preparation never exceeded 150 g. Surface roughness parameters (Ra, Rsk, Rku) were recorded with an optical profilometer and SEM analysis of treated surfaces and working tips was conducted. Ra and Rsk differed significantly between enamel and dentin only after using turbine (p=0.004 and p=0.007, respectively). No significant differences were observed in Ra, Rsk, and Rku between enamel and dentin when using high-speed electric handpiece or piezoelectric device. Turbine produced higher Ra and Rsk values on dentin than the other devices, while no significant differences were found between piezoelectric handpiece and high-speed electric contra-angle on both substrates. Summarizing, the findings of the present study demonstrated that turbine generated rougher surfaces on dentin compared to the other handpieces. Moreover, the turbine produced more asymmetrical surface profiles on both enamel and dentin. However, it should be considered that these differences in roughness (Ra) were within the range of 0.25-0.30 μm: it is still unclear if these variations, although statistically significant, will influence final clinical outcomes.

In the context of energy conversion from renewable sources to distribution grids (insulated or not), a converter is often required to transfer energy from a low voltage source, towards three-phase grids. This paper presents the HW design, the simulation results and the conversion performance of a CSI converter intended to interface low voltages renevable sources to three-phase grids. The main focus of this paper is to obtain the best performance in terms of voltage increase towards the output stage while maximizing the conversion efficiency. In comparison with the currently used energy conversion systems for small photovoltaic systems, hereafter some solutions were adopted to level and maximize the energy flow from the source to the DC-link and improve the quality of current supplied in terms of harmonic distortion. The proposed system is composed of two conversion stages: the first, voltage-to-current, the second current-to-current via a three-phase CSI bridge modulated with SVM technique. The stages are not completely decoupled from an electrical point of view, therefore, in order to mitigate the effects of these interactions, synchronization strategies have been adopted.

The relationship between religion and politics is a constant in the history of humanity. In the specific case of Western culture, it is possible to trace an archeology of the political as an effect of theological-political devices (essentially Christian-inspired). If we add to this the evolution of politics, in modern times, towards biopolitics, then the relationship focuses on very concrete topics. This is the case of the immunological process – from a personal, social, and philosophical perspective – thoroughly analyzed by Italian philosopher Roberto Esposito. In the context of his philosophical immunology, the place of religion is mainly archaeological and is interpreted critically. This article also aims to critically analyze his position, proposing a reading close to his thought but which is, at the same time, somewhat different.

A two-qubit Hamiltonian model exhibiting an SU(2) symmetry is considered. The related dynamical problem results to be then exactly solvable both in the time-independent and in the time-dependent case. Basing on the formal, general form of the related time evolution operator, the time-dependence of the level of entanglement of some initial conditions is studied within both the Rabi and the Landau-Majorana-Stückelber-Zener scenarios.

Background. This study compares the short- and long-term effectiveness and safety of pramipexole augmentation (PA) and aripiprazole augmentation (AA) for unipolar treatment-resistant depression (TRD). Methods. Patients were recruited in a private out-patients clinic specialized in mood disorders. At intake and at each visit depressive and (hypo)manic symptoms, clinical status, and level of functioning were evaluated with appropriate scales. The trend of outcomes was analyzed using mixed-effect linear regression models. Results. The study includes 81 unipolar TRD patients treated with PA and 51 with AA. After 12 and 24 weeks of treatment with PA, the predicted response (64.1% and 76.2%) and remission rates (49.7% and 72.7%) were significantly higher than the predicted response (32.2% and 38.0%) and remission rates (18.9% and 28.1%) for AA. The improvement in psychosocial functioning was significantly greater and faster in PA than in AA. PA showed significant superiority over AA as a maintenance strategy (time spent ill and psychosocial functioning) up to 12 months. No difference in safety was found at each time point. Conclusions. PA could be an alternative option for short and long-term treatment of unipolar TRD, more effective and similar in safety with AA. These preliminary results need confirmation from randomized clinical trials.

The growing interest in environmental sustainability issues and, at the same time, the advantages offered by blockchain technology have strong connections between these two topics. This study explores the application of blockchain technology across various environmental domains, such as air quality, climate change impacts, and resource management. The research utilised a dual approach, combining a bibliometric analysis with VOSviewer and a topic analysis using BERT models to assess the discourse within both scientific literature extracted from Scopus and practical blockchain projects obtained from GitHub. The findings reveal that food security, energy, and sustainable agriculture are predominant topics in academic discussions, with a noticeable increase in focus from 2017 onwards. Practical projects are focused on transparent tracking and decentralised management. The overlap between academic and practical spheres is evident in the shared focus on energy and environmental management, demonstrating blockchain’s growing role in addressing global environmental challenges. The study underscores the importance of integrating theoretical research with practical implementations to harness blockchain’s full potential in promoting sustainable environmental practices.

The Reactive Spark Plasma Sintering (R-SPS) method is compared in this work with the two-steps SHS-SPS route, based on combination of the Self-propagating High-temperature Synthesis (SHS) with the SPS process, for the fabrication of dense (Hf0.2Mo0.2Ti0.2Ta0.2Nb0.2)B2-SiC and (Hf0.2Mo0.2Ti0.2Ta0.2Zr0.2)B2-SiC ceramics. A multiphasic and inhomogeneous product, containing various borides, is obtained at 2000°C/20min by R-SPS, from transition metals, B4C and Si. In contrast, if the same precursors are first reacted by SHS, and then processed by SPS under the optimized condition of 1800°C/20min, the desired ceramics are successfully attained. Both High-Entropy-Boride/SiC products display densities > 97%, uniform microstructures and contained only small amounts of residual oxides (<2.4 wt.%). The presence of SiC makes the sintering temperature milder, i.e. 150°C below to that needed by the corresponding additive-free system. Fracture toughness is also markedly improved, particularly when considering the Nb-containing system processed at 1800°C/20min, whereas KIC progressively decreases (from 7.35 to 5.36 MPa m1/2) as the SPS conditions become more severe. SiC addition is found to inhibit the volatilization of metal oxides like MoO3 formed during oxidation experiments, thus avoiding mass loss in the ceramics. The benefits above also likely take advantage of the fact that the two composite constituents are synthesized in parallel, according to the SHS-SPS approach, rather than being produced separately and combined subsequently, so that strong interfaces between them are formed.

Capturing atmospheric CO2 and storing it in natural rock systems (i.e., alkaline earth silicate and hydroxide minerals) through carbonation reactions is a promising greenhouse gas mitigation research, and largely depends on the use of hydrated ultramafic rocks (serpentinites), which are widespread in orogenic belts around the globe. The Jurassic ophiolites in the Southern Apennines represent a natural analogue and a great opportunity for the mineralogical sequestration of CO2. Serpentinites of the Pollino ophiolite Massif have been widely studied for their mineralogical, petrographic, and chemical characteristics, providing major findings on their impact on environmental and human health issues. Serpentinites here have been divided into cataclastic and massive types based on their structures and are characterized by pseudomorphic and vein textures. The mineralogy of the studied serpentinites consists of lizardite, antigorite, clino-crysotile, Cr-chlorite, magnetite, tremolite, actinolite, pyroxene and calcite, and the most commonly occurring serpentine minerals are polymorphs of serpentine including lizardite, clino-crysotile and antigorite. Systematic petrographic and mineralogical studies of serpentinites in ophiolites, such as those outcropping in the Southern Apennines can represent a starting point for the study of natural materials, which can be used for CO2 storage and sequestration. A particular attention must be given to those carbonate phases, produced by carbonation processes to check whether the serpentinites of the Pollino Massif can be used for the induced mineral Carbon Capture Storage (CCS). If successful, this technique and the Pollino Massif serpentinites can become highly significant in safeguarding the health of our planet's climate.

The versatility of metal complexes of corroles raised the interest in the use of these molecules as element of chemical sensors. The tuning of the macrocycle properties by synthetic modification of the different components of the corrole ring, such as functional groups, molecular skeleton, and coordinated metal, allows the creation of a vast library of corrole-based sensors. However, the scarce conductivity of most of aggregates of corroles limits the development of simple conductometric sensors and requires the use of optical or mass transducers that are rather more cumbersome and less prone to be integrated in microelectronics systems. To compensate the scarce conductivity, corroles are often used to functionalize the surface of conductive materials such as graphene oxide, carbon nanotubes, or conductive polymers. Alternatively, they can be incorporated in heterojunction devices where they are interfaced with a conductive material such as a phthalocyanine. Herewith, we introduce two heterojunction sensors made of junctions of lutetium bisphthalocyanine (LuPc2) with either 5,10,15-tris(pentafluorophenyl) corrolato Cu (1) or 5,10,15-tris(4-methoxyphenyl)corrolato Cu (2). Optical spectra show that after forming the heterojunction, corroles maintain their original structure. The conductivity of the devices reveals an energy barrier for interfacial charge transport, which is larger in the 1/LuPc2 device. The different interfacial barriers is also manifested by the opposite response respect to ammonia: with a 1/LuPc2 behaving as a n-type conductor and 2/LuPC2 as a p-type conductor. Furthermore, the sensors show a high sensitivity respect to relative humidity with a reversible and fast response in the range 30-60%.

Recent studies have shown correlations between the microbiota's composition and various health conditions. Machine learning (ML) techniques are essential for analyzing complex biological data, particularly in microbiome research. ML methods help analyze large datasets to uncover microbiota patterns and understand how these patterns affect human health. This study introduces a novel approach combining statistical physics with the Monte Carlo (MC) methods to characterize bacterial species in the human microbiota. We assess the significance of bacterial species in different age groups by using notions of statistical distances to evaluate species prevalence and abundance across age groups and employing MC simulations based on statistical mechanics principles. Our findings show that the microbiota composition experiences a significant transition from early childhood to adulthood. Species such as Bifidobacterium breve and Veillonella parvula decrease with age, while others like Agathobaculum butyriciproducens and Eubacterium rectale increase. Additionally, low-prevalence species may hold significant importance in characterizing age groups. Finally, we propose an overall species ranking by integrating the methods proposed here in a multicriteria classification strategy. Our research provides a comprehensive tool for microbiota analysis using statistical notions, ML techniques, and MC simulations.

Objective: Interstitial fibrosis / tubular atrophy (IFTA) is a common, irreversible, and progressive form of chronic kidney allograft injury, and it is considered a critical predictor of kidney allograft outcomes. The extent of IFTA is estimated through a graft biopsy, while a non-invasive test is lacking. The aim of this study was to evaluate the feasibility and accuracy of an MRI radiomic-based machine learning (ML) algorithm in estimating the degree of IFTA in a cohort of transplanted patients. Approach: Patients who underwent MRI and renal biopsy within a 6-month interval from 1/1/2012 to 1/3/2021 were included. Stable MRI sequences were selected, and renal parenchyma, renal cortex and medulla were segmented. After image filtering and pre-processing, we computed radiomic features which were subsequently selected through a LASSO algorithm for their highest correlation with the outcome and lowest intercorrelation. Selected features and relevant patients’ clinical data were used to produce ML-algorithms using 70% of the study cases for feature selection, model training and validation with a 10-fold cross-validation, and 30% for model testing. Performances were evaluated using AUC with 95% confidence interval. Main results: 70 coupled tests (63 patients, 35.4% females, mean age 52.2 years) have been included and subdivided into a wider cohort of 50 for training and a smaller cohort of 20 for testing. For IFTA ≥ 25%, AUCs in test cohort were 0.60, 0.59, and 0.54 for radiomic features only, clinical variables only, and combined radiomic-clinical model, respectively. For IFTA ≥ 50%, AUCs in training cohort were 0.89, 0.84, 0.96, and in test cohort were 0.82, 0.83, and 0.86, for radiomic features only, clinical variables only, and combined radiomic-clinical model, respectively. Significance: An ML-based MRI radiomic algorithm showed promising discrimination capacity for IFTA>50%, especially when combined with clinical variables. These results need to be confirmed in larger cohorts.

In the conservation of monumental heritage, the collection and utilization of information are of primary importance. The Heritage Building Information Modeling (HBIM) procedure harnesses the potential of three-dimensional models, offering significant advantages in accessing documentation, interoperability, multidimensionality of intervention design, cost evaluation and maintenance management. Attention here is focused on the Certosa di Pisa, a large historical complex built in the 14th century as a monastery of the Carthusian order, currently in a state of deterioration and in need of restoration and re-functionalization. The multifaceted nature of this monumental complex, with its intricate interplay of architectural elements spanning different historical periods and featuring diverse techniques, poses a significant challenge for structural safety assessment. This case study presents an opportunity to explore an HBIM approach to streamline the diagnostic process and facilitate the intervention design phase. The goal is achieved by utilizing an accurate 3D model enriched with data from multiple sources and automating certain operations for structural assessment. The usefulness of the HBIM methodology is highlighted as a valuable tool in the realm of Cultural Heritage structures for both technicians and scholars alike.

This work deals with the performance evaluation of novel flat photovoltaic-thermal (PV-T) modules under vacuum. Through a 1D (dimensional) steady-state-energy-balance numerical model developed in MATLAB, two different layouts are studied: the first consisting of a photovoltaic (PV) cell installed just below the glass encapsulating the flat panel, and the second where the PV cell is placed on the selective solar absorber (SSA). In both cases the thermal and electrical efficiencies have been evaluated at different SSA operating temperatures, in the range of 323 K to 423 K. The analysis has been conducted at different energy bandgap (E_bg) of the PV cell and assuming a variable transmittance or emittance of the PV cell, depending on the design. The two systems efficiency comparison has been carried out at the same operating temperature. Overall, this work highlights the importance of high vacuum insulation, which guarantees the reduction of convective thermal losses, and shows that the maximum energy is produced for PV cells with E_bg ≈1.5-1.7 eV, depending on layout and operating temperature, by including the thermal output in the PV-T optimization. The energy and exergy efficiencies obtainable using the proposed PV-T systems are considerably improved compared to the results previously reported in the literature.

A number of studies suggested that influenza vaccination can provide protection against COVID-19 but the underlying mechanisms that could explain this association is still unclear. In this study, the effect of the 2021/2022 seasonal influenza vaccination on the immune response to the booster dose of anti-SARS-CoV-2 vaccination was evaluated in a cohort of healthy individuals. One hundred and thirteen participants were enrolled, and 74 of them with no prior COVID-19 diagnosis or significant co-morbidities were considered for the analysis. Participants received the anti-influenza tetravalent vaccine and the booster dose of the anti-SARS-CoV-2 vaccine or the anti-SARS-CoV-2 vaccine alone. Blood was collected before and 4 weeks after each vaccination and 12 weeks after SARSCoV2 vaccination and analyzed for anti-flu and anti-spike-specific antibody titers and for in vitro influenza and SARS-CoV-2 neutralization capacity. Results indicated an increased reactivity in subjects who received both influenza and SARSCoV2 vaccinations, as compared to those who received only the SARS-CoV-2 vaccine, with sustained anti-spike antibody titers up to 12 weeks post-vaccination. Immune response to influenza vaccine was evaluated and individuals were stratified as high or low responders. High responders showed increased antibody titers against SARSCoV2 vaccine both after 4- and 12-weeks post-vaccination. On the contrary, the individuals classified as low responders were less responsive to the SARS-CoV-2 vaccine. These data indicate that both external stimuli, such as influenza vaccination, and the host's intrinsic ability to respond to stimuli play a role in the response to vaccine.

The present review compared the efficacy of soft tissue substitutes (STS) and autogenous free gingival graft (FGG) or connective tissue graft (CTG) in mucogingival procedures to increase keratinized tissue (KT) width around teeth and implants. Two independent examiners performed the electronic search on Medline and Cochrane Library based on the following PICO’s format: (P) adult patients; (I) soft tissue substitutes and FGG/CTG; (C) STS vs CTG; STS vs FGG; STS vs CTR; (O) KT width gain; (S) Systematic Reviews, Randomized Controlled Trials. Results showed that around teeth, all biomaterials showed superior performance compared to CAF alone for treating gingival recessions. However, when compared to CTG, ADM yields the most similar outcomes to the gold standard (CTG), even though in multiple recessions CTG still continue to be considered the most favorable approach. Use of STSs (acellular matrix or tissue engineered) in combination with an apically positioned flap resulted in a significantly less gain of KTW compared to what achieved with FGG and APF. Around dental implants, free gingival grafts were deemed more effective than soft tissue substitutes in enhancing keratinized mucosa width.

Inertial focusing based Lab-on-Chips represent nowadays a promising technology for cell sorting in various applications, thanks to their coherence with the ASSURED criteria recommended by the World Health Organization, being: Affordable, Sensitive, Specific, User-friendly, Rapid and Ro-bust, Equipment-free and Delivered. Inertial focusing in spiral microchannel can offer a rapid, portable and ease of prototyping solution for cell-sorting. In literature, different geometries of microfluidic channel have been investigated to understand how hydrodynamic forces, due to primary and secondary flow, influence particle focusing. The balancing of these forces in spiral microchannels allows for high throughput and filtration efficiency across different particle and sizes. The understanding of such mechanism represents a key aspect to address the prototyping of spiral devices for the target application. A clear, complete and orderly overview in the current literature is lacking. For this reason, we aim to compare the main features of inertial focusing depending on various cross-section (rectangular, trapezoidal, triangular, hybrid) in spiral devices. Additionally, details about materials and prototyping techniques will be provided. This review study will provide readers a comprehensive overview of current research, guiding future ex-perimentation by expediting the selection of spiral geometries and materials based on the type of particle to be separated.

Weight thresholding (WT) is a method intended to decrease the number of links within weighted networks that may otherwise be excessively dense for network science applications. WT aims to remove links to simplify the networks by holding most of the features of the original network. Here, we test the robustness and the efficacy of the node attack strategies on real-world networks subjected to WT that remove links of higher weight (strong links). We measure the network robustness along node removal with the largest connected component (LCC). We find that the real-world networks under study are generally stable in terms of robustness when subjected to WT. Nonetheless, WT by strong link removal changes the efficacy of the attack strategies and the rank of node centralities. Also, WT by strong link removal may trigger a greater change in node centrality rank than WT by removing weak links. Network science research finding important/influential nodes in the network has to consider that simplifying the network with WT methodologies may change the node centrality.

Ultrasound (US) scans of the inferior vena cava (IVC) provide useful information on the volume status of a patient. However, their investigation is user-dependent and prone to measurement errors. An important technical problem is the objective difficulty in studying a very compliant blood vessel like IVC, which makes large respirophasic movements and shows a complicated three dimensional geometry. Using bi-dimensional (2D) B-mode views either in long or short axis has improved the characterization of IVC dynamics compared to a measurement along a single direction (M-mode). However, specific movements of the IVC can challenge also the information provided by these 2D sections. Thus, these two orthogonal views, provided by an US system in X-plane, are here integrated by an innovative method. It is tested on simulated videos of the IVC performing complicated movements, that are compensated by the new method, overcoming the biased measurements provided by 2D scans. The method is then applied on example experimental data.

Hematological malignancies refer to a heterogeneous group of neoplastic conditions of lymphoid and hematopoietic tissues classified in leukemias, Hodgkin and non-Hodgkin lymphomas and multiple myeloma, according to their presumed cell of origin, genetic abnormalities, and clinical features. Metabolic adaptation and immune escape, which influence various cellular functions including proliferation and survival of hematological malignant tumor cells, are major aspects of these malignancies that lead to therapeutic drug resistance. Targeting specific metabolic pathways is emerging as novel therapeutic strategy in hematopoietic neoplasms, particularly in acute myeloid leukemia and multiple myeloma. In this context, CD147, also known as Extracellular Matrix Metalloproteinase Inducer (EMMPRIN) or Basigin, is one target-candidate involved in reprogramming metabolism in different cancer cells, including hematological malignant tumor cells. CD147 overexpression significantly contributes to the metabolic transformation of these cancer cells, by mediating signaling pathway, growth, metastasis and metabolic reprogramming, through its interaction, direct or not, with various membrane proteins related to metabolic, regulation including monocarboxylated transporters, integrins, P-glycoprotein and Glucose Transporter 1. This review explores the metabolic functions of CD147 and its impact on the tumor microenvironment, influencing the progression and neoplastic transformation in leukemias, myeloma and lymphomas. Furthermore, we highlight new opportunities for the development of targeted therapies against CD147, potentially improving the treatment of hematologic malignancies.

Keywords: Rhinoplasty - Augmentation rhinoplasty - Open rhinoplasty - Facial rejuvenation – Centrofacial lipofilling.

The object of this research project is the investigation of the forgotten landscape of transhumance in mainland Greece, focusing on areas abandoned by modern society and their historical passage. The objective is to revive these lands by restoring their cultural heritage and creating a sustainable community that balances the needs of people, livestock, and the environment. The investigation employs a dual approach: studying transhumance as a cultural and natural practice and analyzing anonymous architecture to preserve collective memory. This involves extensive historical research and a simultaneous analysis of spatial, social, symbolic, and architectural elements. The study identifies convergence points between cultural practices and architectural heritage, applying these insights to modern redevelopment scenarios. Findings reveal a significant interplay between transhumance practices and the region’s anonymous architecture. Key characteristics of the landscape and its spatial identity are documented, providing insights into effective preservation and redevelopment strategies. Specific case studies validate these strategies, demonstrating their relevance to current and future efforts. The study concludes that understanding the historical context and spatial identity of transhumance landscapes is crucial for sustainable redevelopment. By preserving cultural practices and architectural heritage, this project offers a framework for revitalizing these forgotten landscapes, ensuring balanced coexistence of people, livestock, and the environment.

At present European buildings typically consume two to five times more energy than predicted at the design stage. An important cause of this performance gap is the discrepancies between the design specification and the As-Built condition. Such discrepancies are mainly due to the gaps in knowhow between design, production and construction professionals. Design is more and more contained into a virtual environment and loses touch with the physical production and construction sites. As the construction sector enters the Industry 4.0 era, Building Information Modelling (BIM) based Mixed Reality can intertwine virtual and real worlds to bridge the knowhow gaps.

Segregating one space from another is a rudimentary act of architecture and the basic principle of this act is creating differentiation between outside and inside. Thresholds, in their expanded or summed form, also produce spaces. They establish the staging for threshold areas in conjunction with space-defining elements. Threshold spaces are typically complicated spatial formations that serve as transition points. They pose a challenge to the interacting human senses in terms of perception. In this research threshold areas have been studied under a specific typology of architecture i.e the traditional housing in historic cities of India. The traditional dwelling settlements have evolved and grown over multiple layers of history, influenced by the culture, society, economy, climate and topography. The purpose of this research is to examine the characteristics of these transition spaces of the traditional dwelling units in relation to the symbolic reference and social meanings assigned to them that influence the architectural and urban spaces attached to them. It seeks to describe transition space in terms of its nature, character, morphology, and social significance. Transparency and material articulation, as well as hierarchy and enclosure, will be investigated. The importance and quality of the nature of "transition" will be examined from the inside to the outside. The research reveals that the space has great functional and socio-cultural importance. It allows multiple activities, provides protection from sun and rain, defines boundaries, connects people within the neighborhood, enhances security and gives an identity to the owner. The contributions made by this research have the potential to improve design considerations for transition areas between the dwelling units and the street.

This paper describes the first results of an Image Recognition Based Location (IRBL) for mobile application focusing on the procedure to generate a Database of range images (RGB-D). In an indoor environment, to estimate the camera position and orientation, a prior spatial knowledge of the surrounding is needed. In order to achieve this objective a complete 3D survey of two different environment (Bangbae metro station of Seoul and E.T.R.I. building in Daejeon – Republic of Korea) was performed using LiDAR (Light Detection And Ranging) instrument and the obtained scans were processed in order to obtain a spatial model of the environments. From this, two databases of reference images were generated using a specific software realized by the Geomatics group of Politecnico di Torino (ScanToRGBDImage). This tool allow to generate synthetically different RGB-D images) centered in the each scan position in the environment. Later, the external parameters (X, Y, Z, ω, φ, κ) and the range information extracted from the DB images retrieved, are used as reference information for pose estimation of a set of acquired mobile pictures in the IRBL procedure. In this paper the survey operations, the approach for generating the RGB-D images and the IRB strategy are reported. Finally the analysis of the results and the validation test are described.

Treatment of HIV-associated lymphoma (HIV-Ly) with autologous stem cell transplantation (ASCT) has shown a surprisingly low relapse rate in several series. The aim of this study was to compare the clinical outcomes of HIV-Ly and lymphomas of the general population receiving ASCT. We compared two series of consecutive HIV-positive and HIV-negative patients, based on a 1:1 propensity score analysis, matching for age, sex, histology, disease status and prior therapies. We identified 44 patients in both groups. All HIV-positive patients received combination antiretroviral therapy (cART). With a median follow-up of 51 months, PFS was significantly higher in HIV-positive patients (4-years PFS 81% and 51%, in HIV-positive and HIV-negative patients, respectively, p=0.027). Four-year OS was 81% for HIV-positive and 67% in HIV-negative patients (p=0.15). The relapse rate was significantly higher in HIV-negative patients (36% vs 23%) (p=0.04). Our results clearly show that ASCT is an effective curative option for HIV-Ly, with better PFS and lower relapse rate compared to uninfected patients. A favourable effect of ASCT on HIV infection and immune system recovery, potential off-target effects of cART or other yet unknown factors may account for this observation.

Sleep timing is one of the dimensions of sleep that refers to the time of day when sleep occurs. It was included in sleep-related research because of the potential associations between overweight and consumption of meals and snacks. This cross-sectional study aimed to investigate associations between sleep timing, meal and snack consumption, and weight status in 1333 schoolchildren aged 7-14 years. The midpoint of sleep was used as a sleep timing measure obtained by the midpoint between bedtime and wake-up time and classify as Early, intermediate, and Late. Schoolchildren in the Early group were less likely to be overweight (OR: 0.83, 95% CI 0.69; 0.99), had higher odds of mid-morning snack consumption (OR: 1.95, 95%CI 1.56; 2.44) and lower probability to consume the evening snack (OR: 0.75, 95%CI 0.59; 0.94) compared with the Intermediate group. The Late group had lower odds of mid-morning snack consumption (OR: 0.67, 95%CI 0.55, 0.80) than the Intermediate group. The consumption of mid-morning and evening snacks was associated with the Early and the Late midpoint of sleep. These results suggest that bedtime and wake-up time are relevant to consuming meals and snacks and may also be related to a greater probability of being overweight in children and adolescents.

Several studies have shown that combining TiO2 and Cu2O enhances the photocatalytic activity of the material by generating a heterojunction capable of extending the light absorption in the visible and reducing the electron-hole recombination rate. Ball milling has been chosen as an alternative methodology for photocatalyst preparation, among the several techniques documented in the literature review. The results of a previously reported investigation enabled the identification of the most effective photocatalyst that can be prepared for hydrogen generation by combining Cu2O and TiO2 (i.e., 1%wt Cu2O in TiO2 photocatalyst prepared by ball-milling method at 200 rpm and 1 min milling time). To optimize photocatalytic hydrogen generation in the presence of the greatest photocatalyst, the effects of (i) sacrificial species and their concentration, (ii) temperature, and (iii) pH of the system are taken into account, resulting in a light-to-chemical energy efficiency of 8% under the best-tested conditions. Last but not least, the possibility of using the present photocatalytic system under direct solar light irradiation is evaluated: the results indicate that nearly 60% of the hydrogen production recorded under sunlight can be attributed to the visible component of the solar spectrum, while the remaining 40% can be attributed to the UV component.

This study refers to the optimization of a Selective Solar Absorber to improve the Sun-to-thermal conversion efficiency at mid temperatures in high vacuum flat thermal collectors. Efficiency has been evaluated by using analytical formula and a numerical thermal model. Both results have been experimentally validated using a commercial absorber in a custom experimental set-up. The optimization procedure aimed at obtaining Selective Solar Absorber is presented and discussed in the case of a metal dielectric multilayer based on Cr2O3 and Ti. The importance of adopting a real spectral emissivity curve to estimate high thermal efficiency at high temperatures in selective solar absorber is outlined. Optimized absorber multilayers can be 8% more efficient than the commercial alternative at 250 °C operating temperatures and up to 27% more efficient at 300 °C. Once the multilayer has been optimized the choice of a very low emissivity substrate such as copper allows to further improve efficiency and to reach stagnation temperature higher than 400 °C without Sun concentration.

The aim of the present study was to investigate the incidence of breast (females), prostate, testicular and thyroid cancer in the Italian National Priority Contaminated Sites (NPCSs), served by cancer registries, where the presence of endocrine disruptors (EDs), reported to be linked to these tumors, was documented. Evidence of carcinogenicity of EDs present in NPCs was assessed based on evaluation by international scientific institutions/committees. Standardized Incidence Ratios (SIRs) were computed for each NPCS and cancer site with reference to the time window 1996-2005. Excess incidence of one or more cancer site at study was found in twelve out of fourteen NPCSs. Significantly increased SIRs were found for breast cancer in eight NPCSs, for prostate cancer in six, for thyroid cancer (both gender) in four and for testicular cancer in two. Non significantly increased SIRs were found in five NPCSs for testicular cancer and in two for thyroid cancer (males). Even if increased incidence of one or more cancer sites at study were found in several NPCSs, the ecological study design and the multifactorial etiology of the considered tumors do not allow reaching conclusions in terms of causal links with environmental contamination. In light of the observation of some excesses in SIRs, continuing epidemiological surveillance is warranted.

Background: Current management of COPD is predominantly focused on respiratory aspects. A multidimensional assessment including nutritional assessment, quality of life and disability provides a more reliable perspective of the true complexity of COPD patients. Methods: Prospective observational study of 120 elderly COPD patients at high risk of acute exacerbations. The Mini-Nutritional Assessment (MNA) was administered in addition to the usual respiratory assessment. The primary outcome was a composite of moderate or severe acute exacerbations during 52 weeks of follow-up. Results: The median MNA Short Form (SF) score was 11 (8-12), 39 participants (32.50%) had normal nutritional status, 57 (47.5%) were at risk of malnutrition and 24 (20%) were malnourished. Our multivariate linear logistic models showed that the MNA score was associated with dyspnea and respiratory symptoms severity assessed by the Modified British Medical Research Council (mMRC) and the COPD Assessment Test (CAT) score, with spirometric variables, in particular with the severity of airflow limitation based on the value of FEV1 and with poorer QoL as assessed by the EQ-5D-3 questionnaire. Cox regression analysis according to nutritional status based on the MNA score showed that COPD participants "at risk of malnutrition" and "malnourished" had a higher risk of moderate to severe acute exacerbations with a hazard ratio (HR) of 3.54 (p=0.002) and 8.20 (p=0.0001), respectively. Conclusion: Our study confirms the importance of assessing nutritional status in elderly COPD patients and its prognostic value.

This paper presents the design and analysis of a novel 3-degree-of-freedom (3-DOF) parallel ma-nipulator equipped with self-sensing Ni-Ti (Nitinol) actuators. The manipulator's architecture and mechanical design are elucidated, emphasizing the integration of Nitinol actuators. The self-sensing technique implemented in a previous work was extended to a 20 mm actuator length, and the actuator was used to design the 3 DOF manipulator. Kinematic analyses were conducted to eval-uate the manipulator's performance under various operating conditions. A dynamic model was implemented for the dynamic dimensioning of the actuators, which work synergistically with a bias spring. The manipulator was realized, and a control strategy was implemented. Experimental tests, although documenting some positioning accuracy issues, show the efficacy and potential applica-tions of the proposed manipulator in robotics and automation systems, highlighting the advantages of self-sensing Nitinol actuators in small parallel manipulator designs.

Amyotrophic lateral sclerosis (ALS) is a fatal neuromuscular disease, characterized by progressive degeneration of upper and lower motor neurons in the cortex and spinal cord. Although the pathogenesis of ALS remains unclear, evidence on the role of the clonotypic immune system is growing. Adaptive immunity cells often appear changed in number or activation profile peripherally and centrally. However, their role in ALS appears conflicting. Data, from human and animal model studies, currently reported in literature show that each subset of lymphocytes and their mediators may mediate a protective or toxic mechanism in ALS, affecting both its progression and risk of death. In the present review article and attempt is made to shed light on the actual role of the cellular clonotypic immunity in ALS by integrating recent clinical studies and experimental observations.

The application of space robotic manipulators and heightened autonomy for ios represents a paramount pursuit for leading space agencies, given the substantial threat posed by space debris to operational satellites and forthcoming space endeavors. This work presents a guidance algorithm based on drl to solve for the space manipulator path-planning during the motion synchronization phase with the mission target. The goal is the trajectory generation and control of a spacecraft equipped with a 7-dof robotic manipulator, such that its end effector remains stationary with respect to the target point of capture. The ppo drl algorithm is used to optimize the manipulator’s guidance law, and the autonomous agent generates the desired joints rates of the robotic arm, which are then integrated and passed to a model-based feedback linearization controller. The agent is first trained to optimize its guidance policy and then tested extensively to validate the results against a simulated environment representing the motion synchronization scenario of an ios mission.

Background: Bioaerosol can represent a danger to the health. During SARS-CoV-2 pandemic, portable devices were used in different environments and considered a valuable prevention tool. This study has evaluated the effectiveness of the air treatment device “AEROK 1.0” in reducing microbial, particulate and pollen airborne contamination indoors, during normal activity. Methods: In an administrative room, airborne microbial contamination was measured using active (DUOSAS 360 and MD8) and passive sampling; a particle counter was used to evaluate particle concentrations; a Hirst-type pollen trap was used to assess airborne pollen and Alternaria spores. Statistical analysis was performed using SPSS 26.0; p values <0.05 were considered statistically significant. Results: The airborne bacterial contamination assessed by the two different samplers decreased by 55.54% and 69.13%, respectively. The airborne bacterial contamination assessed by passive sampling decreased by 44.16%. For fungi, the reduction was 38.7% by active sampling. Airborne particles (diameters ≥ 1.0, 2.0 μm) and the ratio of indoor/outdoor concentrations of total pollen and Alternaria spp spores significantly decreased. Conclusions: The results highlight the effectiveness of AEROK 1.0 in reducing airborne contamination. The approach carried out represents a contribution to the definition of a standardized model for evaluating the effectiveness of this type of devices.

Monitoring the integrity of aeronautical structures is fundamental for safety. Structural Health Monitoring Systems (SHMS) perform real-time monitoring functions, but their performances must be carefully assessed. In this work the damage detection performances of a strain-based SHMS, were evaluated on a composite helicopter rotor blade root. The SHMS monitored the bonding between the central core and the surrounding antitorsional layer. A damage detection algorithm was trained through Finite Element analyses performed on the component. The effects of the loads variability and of damages were decoupled by including a load recognition step in the algorithm. Load recognition was accomplished in different ways: version#1 adopted an Artificial Neural Network (ANN) trained on blades in pristine condition; version#2 was trained also on damaged blades; version#3 adopted a calibration matrix method. Anomaly detection, damage assessment, and localization were performed by using an ANN. Results showed a higher load identification and anomaly detection accuracy for version#1 and version#2 compared to version#3. Gaussian noise reduced anomaly detection and damage assessment performances, and reduced damage localization accuracy for bigger damages. The damage detection performance were obtained for a fibre optic based-SHMS, including the trade-off between probability of detection and false alarm rate for different damage sizes.

Several rheumatologic diseases are primarily distinguished by their involvement of bone tissue, where it not only serves as a mere target of the condition but often plays a pivotal role in its pathogenesis. This scenario is particularly prominent in chronic inflammatory arthritis such as rheumatoid arthritis (RA) and spondyloarthritis (SpA). Given the immunological and systemic nature of these diseases, in this review, we report an overview of the pathogenic mechanisms underlying the specific bone involvement, focusing on the complex interactions that occur between bone tissue's own cells and the molecular and cellular actors of the immune system, a recent and fascinating field of interest defined osteoimmunology. Specifically, we have comprehensively elaborated on the distinct pathogenic mechanisms of bone erosion seen in both rheumatoid arthritis and spondyloarthritis, as well as the characteristic process of aberrant bone formation observed in spondyloarthritis. Lastly, chronic inflammatory arthritis lead to systemic bone involvement, resulting in systemic bone loss and consequent osteoporosis, along with increased skeletal fragility.

Dealing with and maintaining high-quality standards in the design and construction phases is challenging, especially for on-site construction. Issues like improper implementation of building components and poor communication can widen the gap between design specifications and actual conditions. To prevent this, particularly for energy-efficient buildings, it's vital to develop resilient, sustainable strategies. These should optimize resource use, minimize environmental impact, and enhance livability, contributing to carbon neutrality by 2050 and climate change mitigation. Traditional post-occupancy evaluations, which identify defects after construction, are impractical for addressing energy performance gaps. A new, real-time inspection approach is necessary throughout the construction process. This paper suggests an innovative guideline for prefabricated buildings, emphasizing digital 'self-instruction' and 'self-inspection'. These procedures ensure activities impacting quality adhere to specific instructions, drawings, and 3D models, incorporating relevant acceptance criteria to verify completion. This methodology, promoting alignment with planned energy-efficient features, is supported by BIM-based software and Augmented Reality (AR) tools, embodying Industry 4.0 principles. BIM and AR bridge the gap between virtual design and actual construction, improving stakeholder communication and enabling real-time monitoring and adjustments. This integration fosters accuracy and efficiency, key for energy-efficient and Nearly Zero-Energy Buildings, marking a shift towards a more precise, collaborative, and environmentally sensible construction industry.

The ability of recombinant, SARS-CoV-2 Spike (S) protein to modulate the production of two COVID-19 relevant, pro-inflammatory cytokines (IL-6 and IFN-γ) in PBMC cultures of healthy, pre-Covid-19 subjects was investigated. We observed that cytokine production was largely and diversely modulated by the S protein depending on antigen or mitogen stimulation, as well as on the protein source, insect (S-in) or human (S-hu) cells. While both proteins co-stimulated cytokine production by polyclonally CD3-activated T cells, PBMC activation by the mitogenic lectin Concanavalin A (Con A) was up modulated by S-hu protein and down-modulated by S-in protein. These modulatory effects were likely mediated by the S glycans as demonstrated by direct Con A-S binding experiments and use of yeast mannan as Con A binder. While being ineffective in modulating memory antigenic T cell responses, the S proteins and mannan were able to induce IL-6 production in unstimulated PBMC cultures and upregulate the expression of Mannose Receptor (CD206), a marker of anti-inflammatory M2 macrophage. Our data point to a relevant role of N-glycans, particularly N-mannosidic chains, decorating the S protein in the immunomodulatory effects here reported. These novel biological activities of the S glycan ectodomain may add to the comprehension of Covid-19 pathology and immunity to SARS-CoV-2.

Art therapy has a long history of applications in cognitive and motor rehabilitation. More recently, a growing body of scientific literature has highlighted the potential of virtual reality in neurorehabilitation, though it has focused more on the technology itself than on the principles adopted in digital scenarios. This study is a randomized controlled trial conducted on 40 patients with stroke, comparing a protocol of art therapy administered in virtual reality, which exploits the so-called Michelangelo effect, to conventional therapy. After 12 sessions, patients in the virtual art therapy group showed a significantly greater improvement in independence in activities of daily living, as assessed by the Barthel Index (interaction of time and group: p<0.01). Significant differences were also found in terms of upper limb muscle strength (Manual Muscle Test, p<0.01) and reduction in spasticity (Ashworth scale, p<0.01) in favor of the experimental group. In the virtual art therapy group, the effectiveness of the intervention was significantly correlated with patient participation (Pittsburgh Rehabilitation Participation Scale: R=0.45), patient satisfaction (R=0.50), and the perceived utility of the intervention by the therapist (R=0.47). These findings support the efficacy of virtual art therapy leveraging the Michelangelo effect. Further studies should also focus on cognitive domains that could benefit from this type of approach.

Although the field of geomatics has seen multiple technological advances in the recent years which enabled new applications and simplified the consolidated ones, some tasks remain challenging, inefficient, and time- and cost-consuming. This is the case of accurate tridimensional surveys of narrow spaces. Static laser scanning is an accurate and reliable approach but impractical for extensive tunnel environments; portable laser scanning is on the other hand time-effective and efficient but not very reliable without ground control constraints. This paper describes the development process of a novel image-based multi-camera system meant to solve this specific problem: delivering accurate, reliable, and efficient results. The development is illustrated from the system conceptualization and initial investigations to the design choices and requirements for accuracy. The resulted working prototype has been put to the test to verify effectiveness of the proposed approach.

In this paper we explore extending the concept of common cross-study Common Data Element concepts beyond simple demographics to cover disease-specific concepts relevant to imaging. We test interactively linking the resulting database to the associated images in a federated manner. We examine the use of existing standards, not only for terminology, but for interchange of serialized data in forms familiar to imaging and clinical trials specialists and their dedicated systems. Our intent is to perform preliminary work to inform both the upcoming Imaging Data Commons specifically, as well as more general integration projects beyond imaging.

Optical characterization and thermal aging tests are performed on a sputter-deposited coating, consisting of SiO₂/Cr₂O₃/Cr/Cr₂O₃ layers, designed and developed as a selective solar absorber to be used for unconcentrated solar thermal applications. Both measurements are performed by using a home-made apparatus, which mimics a flat plate collector under high vacuum. A Performance Criterion (PC_η(T)), based on absorber efficiency is proposed, and a forecast of service lifetime is obtained. As a result of the thermal aging tests, the selective solar absorber under study appears to be highly efficient at mid temperatures (up to 573 K) and thermally stable at temperatures (up to 690 K).

It has long been known that phytohormone auxin plays a promoting role in tuber formation and stress tolerance in potatoes. Our study aimed to identify and characterize the complete sets of auxin-related genes that presumably constitute the entire auxin signaling system in potato (Solanum tuberosum L.). The corresponding genes were retrieved from sequenced genomes of the doubled monoploid S. tuberosum DM1-3-516-R44 (DM) of the Phureja group, the heterozygous diploid line RH89-039-16 (RH), and the autotetraploid cultivar Otava. Both canonical and noncanonical auxin signaling pathways were considered. Phylogenetic and domain analyzes of deduced proteins were supplemented by their expression profiling and 3D molecular modeling. The canonical and ABP1-mediated pathways of auxin signaling appeared to be well conserved. Total number of potato genes/proteins presumably involved in canonical auxin signaling is 46 and 108 in monoploid DM and tetraploid Otava, respectively. Among studied potatoes, spectra of expressed genes obviously associated with auxin signaling were partly cultivar-specific and quite different from analogous spectrum in Arabidopsis. Most of the noncanonical pathways found in Arabidopsis appeared to be low probable in potato. This was equally applied to all cultivars used irrespective of their ploidy. Thus, some important features of the (noncanonical) auxin signaling pathways may be variable and species-specific.

Among solar thermal collectors, the evacuated flat panel is emerging as a reference technology for operation at higher temperatures of up to 200 °C with an increased annual energy production owing to both direct and diffuse light capture. Accurate measurements of the optical properties of the selective absorbers used in such devices are key for a reliable estimation of the overall performance. These optical properties must be measured under high vacuum at high temperatures, conditions under which the panels are meant to operate. In this study, we accurately measured these properties using a calorimetric technique. The measurement procedure is based on a power balance equation for a flat sample suspended in a high-vacuum chamber with minimal thermal losses and is well adapted for this class of devices. Calorimetric measurements obtained under Sun and LED light revealed excellent reproducibility and good agreement with those obtained using traditional optical analysis at low temperatures in air. When extended up to the absorber stagnation temperature, which often exceeds 300 °C, the calorimetric measurements started to deviate from the optical measurements, indicating the importance of measuring under the operating conditions.

The commercial aviation industry is constantly evolving, driven by technological innovation and the growing demand for more efficient and environmental friendly transportation solutions. In this context, the design and development of next-generation aircraft is a crucial task, with the goal of reducing environmental impact and improving flight efficiency while continuing to ensure passenger comfort and safety. This paper aims at evaluating the technical feasibility as well as economic and environmental viability of a narrow body aircraft powered by hydrogen for direct combustion. Notably, the paper offers innovative insights regarding the update of literature models for conceptual design, in order to consider the impact of hydrogen fuel on the sizing loop at aircraft level. Moreover, it also focuses on the evaluation of operating costs for the aforementioned aircraft class, highlighting the required model updates and considerations to properly match the effect on costs of the introduction of the innovative fuel. Ultimately, a preliminary analysis of upstream sustainability of the concept, considering fuel life cycle, is provided, in order to understand the overall competitiveness, not only in terms of monetary resources but also of environmental impact, beyond the pure operating life of the airplane.

Chitosan is a biodegradable polymer derived from chitin, that is a versatile material for various biological applications for its attractive properties such as biocompatibility, biodegradability, and non-toxicity. Furthermore, chitosan possesses Second Harmonic Generation properties, that are useful for bio-sensing applications. In this work we explored the possibility to exploit chitosan-based nanospheres as SHG-based bio-sensors, and also as carriers of 89Sr radionuclide, an Active Pharmaceutical Ingredient for radiopharmaceutical treatments in cancer therapy. To load opportunely the Sr ion on the nanospheres, we used a fructose-based Metal Organic Framework, of formula [Sr(C6H12O6)2(H2O)2]Cl2·H2O, because the sugar was able to drive the Sr ions on the chitosan matrix. The Sr-loaded chitosan nanospheres were synthetized, characterized, and their SHG response was measured. The results encouraged us to propose the nanospheres for theranostic purposes, i.e. at the same time valuable for both therapy and diagnostic applications.

Modern organic synthesis is majorly focused on developing environmentally benign synthetic protocols by employing green chemistry principles. Accordingly, in our recent research work, we herein report the use of modified supramolecular host cyclodextrin as an effective solid based green catalyst for accessing structurally diverse and medicinally relevant pyrimidone architectures. The catalyst and the synthesized compounds 4 (a-r) were characterized using FT-IR, NMR and GC-Mass spectroscopy. Major highlights of the reported work include: atom economical process, extremely milder reaction conditions, operational simplicity, high isolated yields, and excellent catalyst turnover number. The molecular docking studies suggest that the compound 4n has the hydrogen bonding, hydrophobic and π-pair interactions with the active site of active sites of CXT M 15 receptor.

Laser-Powder Directed Energy Deposition (DED-LB/Powder) is an additive manufacturing process that is gaining popularity in the manufacturing industry due to its numerous advantages, particularly in repairing operations. However, its application is often limited to case studies due to some critical issues that need to be addressed, such as the degree of internal porosity. This paper investigates the effect of the most relevant process parameters of the DED-LB/Powder process on the level and distribution of porosity. Results indicate that, among the process parameters examined, porosity is less affected by travel speed and more influenced by powder mass flow rate and laser power. Additionally, a three-dimensional finite element transient model was introduced, which was able to predict the development and location of lack-of-fusion pores along the building direction.

This study assessed the associations between host genetic variants and subgingival microbiota in patients with metabolic syndrome (MetS); 103 patients with MetS underwent medical and periodontal examinations and had blood and subgingival plaque samples taken. DNA was extracted and processed (assessing a panel of selected single nucleotide polymorphisms (SNPs) first (hypothesis-testing), and then expanding to a discovery phase. The subgingival plaque microbiome from these patients was profiled. Analysis of associations between host genetic and microbial factors was performed, stratified for periodontal diagnosis. Specific SNPs within RUNX2, CAMTA1 and VDR genes were associated with diversity metrics, with no genome-wide associations detected for periodontitis severity or Mets components at p&lt;10-7. Severe periodontitis was associated with pathogenetic genera and species. Some SNPs correlated with specific bacterial genera, as well as with microbial taxa, notably VDR (rs12717991) with Streptococcus mutans and RUNX2 (rs3749863) with Porphyromonas gingivalis. This is the first study exploring the role of host genotype variation in subgingival microbial dysbiosis in patients with MetS and periodontitis. In conclusion, variation in host genotypes may play a role in the dysregulated immune responses characterizing periodontitis and thus the oral microbiome, suggesting that systemic health-associated host traits further interact with oral health and microbiome.

Chronic wounds remain a significant clinical challenge, necessitating the exploration of novel therapeutic agents. Sedum telephium L. (syn. Hylotelephium telephium (L.) H. Ohba) leaf juice, known for its traditional medicinal uses, was evaluated for its wound healing properties. This study aimed to chemically characterize the leaf juice and assess its efficacy in promoting wound healing in vitro. Fresh leaves were collected and processed to obtain the juice, which was analyzed for polyphenols, flavonoids, polysaccharides, and proteins. Key bioactive compounds, including flavonols such as kaempferol glycosides and quercetin glycosides, were identified. The juice and its polysaccharidic fraction were tested on human keratinocytes (HaCaT) and fibroblasts (HFF-1) to assess cell viability, wound closure, and the production of growth factors and pro-collagen I. Our results indicated that the whole juice significantly enhanced wound closure in both cell types, with a marked increase in fibroblast growth factor (FGF) and LAP(TGF-β1) production in keratinocytes, highlighting its potential mechanisms of action. The polysaccharidic fraction alone showed limited efficacy, emphasizing the importance of the complete phytocomplex. These findings suggest that Sedum telephium L. represents a promising candidate in the setting of skin regeneration and repair.

Background: Malnutrition commonly affects patients with oral squamous cell carcinoma (OSCC), which contributes to worsening prognosis. Moreover, specific strategies for diagnosing and managing malnutrition in OSCC are lacking. Methods: This retrospective study included 52 consecutive patients with OSCC who underwent surgery at the University Hospital of Palermo (I) from Jan 2020 to May 2023. In-hospital nutritional support was provided by a dedicated team. The patients were compared with a historical control group of 11 patients. The nutritional treatment consisted of standard oral (ON) or artificial nutrition (AN). Traditional measurements, including bioimpedance-derived body composition and volumetric reconstruction of the posterior paraspinal muscles at the C3 level based on magnetic resonance imaging (MRI-C3), were obtained in 16 patients to investigate sarcopenia. Results: The patients were categorized according to TNM stage: groups A (TNM stages I-III) and B (IVa-IVc). The prevalence of group A patients was 59.6% in the case group and 90.9% in the control group (P

Infrared thermography is a contactless imaging technique, useful to measure surface temperature at distance which has been widely applied in animal production. The possible applications within the pig husbandry include sow heat detection, reduction of the incidence of neonatal mortality, recognition of febrile state caused by pathogens, study of metabolic efficiency, evaluation of stress caused by heat, by constraints, or by aggressive interaction and meat quality prediction. Even if this technique could be easily influenced by environmental factors, the continuous improvement in the procedures and the decrease in the cost of the equipment will allow in the next future new and more applications in swine farming.

We investigate the performance of a novel flat photovoltaic-thermal (PV-T) module under high-vacuum through a 1D numerical model based on steady-state energy balance, with the aims of optimizing the simultaneous production of thermal and electrical energy. In the proposed design, the photovoltaic (PV) cell is positioned directly above the selective solar absorber (SSA), in a multilayer or fully integrated PV-SSA structure, which allows full exploitation of spectral solar radiation. In fact, in this configuration the losses related to non-absorption of low-energy photons and thermalization, typical of a classical single-junction PV cell, are reduced. The present study is conducted as the emittance and energy bandgap of the PV layer varied, thus admitting a wide variety of materials into the analysis. The dependence of the temperature coefficient, β(%/K), on the energy bandgap of the PV cell is also included. In the last part of the work, we discuss the performance of the proposed evacuated PV-T equipped with a SSA layer and thin film solar cells, namely those made of CdTe, CdS and GaAs. Overall, the paper highlights the great advantage of using high vacuum insulation, which suppresses conductive losses, and the versatility of the proposed system, which could be adapted to the user's needs simply by choosing the appropriate material for the photovoltaic layer.

Hazelnut is a widespread nut species, especially in Europe, that can be consumed raw or roasted, due to its pleasant taste and nutritional properties. Despite the renowned beneficial properties, hazelnuts contain several proteins capable of inducing food allergy in sensitized individuals such as Cor a 2 (profilin), Cor a 8 (lipid transfer protein), Cor a 9 (11S seed storage globulin, legumin-like) and Cor a 11 (7S seed storage globulin, vicilin-like). In the present paper we investigated the effectiveness of autoclave based treatments in decreasing the allergic potential of hazelnut as also assessed by submitting the treated material to in vivo skin prick test and to in vitro immunoblot analysis with sera of allergic individuals exposed to the treated food material. This preliminary analysis shows that autoclave treatment, preceded by hydration and/or followed by drying, seems to be a promising approach and appears to be effective in reducing the allergenicity of hazelnut in most patients, probably due to the denaturation of most major and minor allergenic proteins. This work will open to the opportunity to produce, in perspective, hypoallergenic hazelnut derivatives tolerated by the allergic subjects.

Despite soccer popularity, comparatively little scientific information is available concerning the assessment of youth players’ physiological characteristics. The use of medical software integrating wearable sensors to provide accurate and objective data is necessary. In the present study, the objective assessment of physical performance of 128 adolescent soccer players at two timepoints (pre-season and end-season) has been performed. Participants completed a comprehensive test battery including stability, countermovement jumps (CMJ), plyometric jumps (PJ), agility, and quick feet tests. A single Inertial Measurement Unit (IMU) sensor provided quantitative data on various performance metrics. Principal Component Analysis (PCA) reduced the dataset to four principal components (PCs) explaining over 80% of the variance: power (PC1), balance (PC2), speed/agility (PC3), and stiffness (PC4). Paired samples t-test between the two timepoints showed no significant differences in the PCs between the two timepoints, indicating that the training program did not significantly alter the assessed physical attributes. However, subtle individual changes may still inform personalized training adjustments. The study highlights the importance of continuous monitoring and individualized training strategies to optimize athlete performance and reduce injury risk.

The decarbonization of the built environment, both in new construction and renovation, is crucial to mitigate its relevant impact on climate change and achieve the Paris agreement goals. This study presents a systematic LCA-based methodology to assess the whole life carbon emissions of buildings, applied to a proposal for the regeneration of one of Milan’s disused railway yards. As an entry for the 2020 Reinventing Cities competition, Scalo Lambrate is a project for a mainly residential neighborhood with a public park. Strategies to reduce carbon emissions deriving both from the operational energy and construction and maintenance were evaluated and their effects compared to a reference scenario over a time horizon of 100 years. The results show that, while the opportunities to reduce carbon emissions during the use phase are somehow limited due to the already stringent performance requirements for new builds, the use of fast-growing biogenic materials for construction materials, even if mixed with more traditional ones, can provide a significant reduction of the global warming potential over the whole life cycle, with a reduction of 70% over the baseline. The remaining emissions can be offset with afforestation initiatives that, however, must be assessed against land use issues.

The fabrication of thin-film multilayer structures by sputtering technique usually requires multi-cathode deposition machine. This study proposes a simpler approach based on the RF power modulation: silicon nitride (SiN$_x$) thin films were prepared by RF reactive sputtering in (Ar + N$_2$) atmosphere at room temperature. The samples were analyzed to highlight the effects of different deposition conditions on the morphological and optical properties of the films in the visible and near/mid-IR regions. The refractive index of the films was changed in the range of 1.5 - 2.5 (at $\lambda$=800 nm) by tuning the sputtering power. IR reflectance measurements revealed the absence of spurious (oxygen- or hydrogen-based) phases, while atomic force and scanning electron microscopies confirmed the presence of flat and defect-free samples surfaces.

Introduction: maxillary hypoplasia and mandibular asymmetry may be corrected with orthognathic surgery at the completion of growth. Many patients require segmental Le Fort I osteotomies to obtain the most stable results. Unfortunately, if Invisalign is chosen for pre-surgical preparation, ClinCheck © software does not allow for prediction when these complex surgeries are planned. The objective of this paper was to show the potential of aligners beyond its software in most complex cases like multiple-piece maxillary osteotomies in cleft and non-cleft patients. Method: Thirteen patients who underwent pre-surgical treatment with clear aligners-Invisalign (study group) were matched in terms of diagnosis, surgical procedure, and orthodontic complexity with thirteen patients treated using fixed appliances (control group). A technique based on simple superimposition was devised to enhance the software for creating a suitable occlusion for segmental pre-surgical treatments. Virtual curves following the lower arch were employed to guide the correct pre-surgical positions of the upper teeth. The amount of impressions required in both groups to achieve satisfactory pre-surgical alignment of the segmented arches was compared. Results: one or no refinement phase were needed in the Invisalign group to reach an acceptable pre-surgical occlusion while the amount of pre-surgical impressions taken in order to reach adequate coordination with fixed appliance treatment was slightly higher. The average overall treatment duration did not show a statistically significant variation between the groups. Conclusions: it appears that clear aligner could serve as an effective treatment for individuals with skeletal discrepancies, including cleft and craniofacial anomalies, necessitating segmental Le Fort I osteotomies when aided by the suggested superimposition approach during digital pre-surgical movement simulations. More sophisticated softwares will certainly be implemented in the future.

DR2B and DR2C extracts, from peel of commercially and physiologically ripe eggplants, were studied for the antioxidative cytoprotective properties and anti-HSV-1 activity, in line with the evidence that several antioxidants can impair viral replication by maintaining reducing conditions into the host cells. The antioxidative cytoprotective effects against tBOOH-induced damage was assessed in Caco2 cells, while the antiviral activity was studied in Vero cells; phenolic and anthocyanin fingerprint was characterized by integrated phytochemical methods. Results highlighted different compositions of the extracts, with chlorogenic acid and delphinidin-3-rutinoside as the major constituents; other peculiar phytochemicals were also identified. DR2C resulted able to partly counteract the tBOOH-induced cytotoxicity, with a remarkable lowering of lactate metabolism under both normoxia and hypoxia. DR2B and DR2C reduced ROS production, possessed scavenging and chelating properties. Interestingly, DR2C increased intracellular GSH levels. Furthermore, DR2C inhibited the HSV-1 replication when added for 24 h after viral adsorption, as also confirmed by the reduction of many viral proteins expression. Since DR2C was able to reduce NOX4 expression during HSV-1 infection, its antiviral activity may be correlated to its antioxidant properties. Although further studies are needed to better characterize DR2C activity, the results suggest this extract as a promising new anti-HSV-1 agent.

We present the use of interconnected optical mesh networks for early earthquake detection and localization, exploiting existing terrestrial fiber infrastructure. Employing a Waveplate model, we integrate real ground displacement data from seven earthquakes, magnitudes ranging from four to six, to simulate the strains within fiber cables and collect large set of light’s polarization evolution data. These simulations help to enhance a Machine-Learning model that is trained and validated to detect Primary waves arrivals that precede earthquakes’ destructive Surface waves. The validation results show that the model achieves over 95% accuracy. The Machine-Learning model is then tested against an M4.3 earthquake, exploiting three interconnected mesh networks as a smart sensing grid. Each network is equipped with a sensing fiber placed to correspond with three distinct seismic stations. The objective is to confirm earthquake detection across the interconnected networks, localize the epicenter coordinates by a triangulation method and calculate fibers to epicenter distance. This setup allows early warning generation to municipalities close to epicenter location, and progressing to those further away. The model testing shows 98% of accuracy in detecting primary wave and one-second of detection time, affording nearby areas 21-seconds to take countermeasures, and an extended 57-seconds in more distant areas.

This work aims to shed light on the differential diagnosis of Complex Post-Traumatic Stress Disorder (cPTSD), Post-Traumatic Stress Disorder (PTSD), and Borderline Personality Disorder (BPD) within the context of Intimate Partner Violence (IPV), which represents an extremely inno-vative field of clinical research. To this end, a critical review of the literature was conducted to identify and compare the clinical patterns and symptomatic overlaps among cPTSD, PTSD, and BPD, with an emphasis on their manifestation in both victims and offenders. The results show that despite some symptomatic similarities, cPTSD, PTSD and BPD have distinct clinical patterns in IPV. Disturbances in Self-Organization (DSO), are more commonly in offenders, while the di-agnosis of cPTSD is more aligned with the victims. In addition, cPTSD and characteristics of BPD, such as fear of rejection and instability of identity, constitute risk factors for IPV victimiza-tion. cPTSD is a predisposing factor not only for victims but also for offenders, while PTSD emerges as a consequential factor. The specific pathways linking PTSD, cPTSD, and BPD with IPV have significant implications for clinical practice. Further research is needed to understand these profiles and the mechanisms linking trauma-related features to IPV, which is crucial for imple-menting effective violence prevention programs.

The comparison of three types of ionosonde data from Europe during an Interplanetary Coronal Mass Ejection (ICME) and a Stream Interaction Regions (SIRs) / Corotating Interaction Regions (CIRs) -driven geomagnetic storm event is detailed in this study. The selected events are 16-20 March 2015 for the ICME-driven and 30 May to 04 June 2013 for the SIR/CIR-driven one. Ionospheric data from three European ionosonde stations, namely Pruhonice (PQ), Sopron (SO) and Rome (RO), are investigated. The ionospheric F2-layer responses to these geomagnetic events are analyzed with the ionospheric foF2 and h’F2 parameter, the calculated deltafoF2 and deltahF2 values, ratio of Total Electron Content (rTEC) and Thermosphere, Ionosphere, Mesosphere, Energetics and Dynamics (TIMED) satellite Global Ultraviolet Imager (GUVI) thermospheric [O]/[N2] measurement data. The storm-time and the quiet day mean values are also compared, and it can be concluded that the quiet day curves are similar at all stations while the storm-time ones showed the latitudinal dependence during the development of the storm. As a result of the electron density comparison, during the two events it can be concluded that SSC that characterized the ICME induced a Travelling Atmospheric Disturbance (TAD) seen in the European stations, while this is not in the SIR/CIR-driven ionospheric storm, which showed a stronger and more prolonged negative effect in all stations probably due to the season.

Electronic waste generation has been following a continuously rising trend. With electronics containing a myriad of materials some of which are hazardous, toxic, extremely rare or precious combined with more stringent legislative laws which encourage the reuse and optimised recycling of the materials included in e-waste, the need for a holistic approach is inevitable. Such an approach should not only identify the materials found in the various types of e-waste and their respective quantities but also needs to highlight the possible handling techniques and their respective impacts and associated hazards whether to the environment or human health. Performing such a task manually would be exasperating and costly while requiring extensive resources which might not be met with a justifiable economic gain; thus, the use of the advancement in computational sustainability to draw a complete picture and aid in an informed decision-making process is crucial. The e-waste ontology developed in this paper is one way of addressing the problem since it covers the treatment domain, the hazard and the materials contained within the different types of e-waste. The ontology developed can be used directly from the protégé software or by embedding it into a developed Decision Support System.

A new frontier in solar thermal panel technology can be a high vacuum collector, thick enough to be equipped with solar concentrators based on non-imaging optics, such as the Compound Parabolic Concentrators (CPC). The high vacuum technology guarantees higher operating temperatures thanks to the enhanced thermal insulation, which leads to pay particular attention to the absorber radiative emission. In this paper by means of numerical simulations we compare the efficiency of a flat selective solar absorber under high vacuum to the efficiency of a CPC under high-vacuum collector.

Previous studies show that women with a history of high-grade CIN have a greater risk of subsequent high-grade anogenital intraepithelial neoplasia or cancer, and the risk is greater for vaginal cancer than for anal and vulvar cancers. It is hypothesized that the laparoscopic hysterectomy procedure may cause a higher incidence of VaIN in hysterectomized women. There are few studies addressing this issue and they show mixed results. This study aimed to investigate the incidence of high-grade or worse VaIN in the population of women undergoing hysterectomy for CIN3 or benign uterine disease, illustrate treatment options and follow-up. Methods: This retrospective study was conducted on 170 women who underwent laparoscopic hysterectomy for high-grade cervical intraepithelial neoplasia (CIN3) or benign gynecological disease. The follow-up strategy included performing a cotest and colposcopy with biopsy if necessary. The median time between primary treatment and diagnosis of high-grade VaIN was 18 months. Results: High grade or worse VaIN was found in 8 patients after hysterectomy (4.7%). All cases of high-grade VaIN occurred in women with persistent HPV infection. The most frequent genotype was 16. Women hysterectomized for CIN3 showed an 8-fold greater risk than women hysterectomized for benign disease of developing high-grade VaIN. The risk of VaIN is low in women hysterectomized for benign disease. The risk of developing VaIN is greater in women with viral persistence Conclusion. All these elements suggest that it is the history of HPV-related disease of the lower genital tract and viral persistence, rather than hysterectomy itself, that should be considered a risk factor for the development of high-grade VaIN. After hysterectomy, patients with a history of CIN should undergo annual screening with vaginal dome cytology and HPV testing.

Knowledge is not merely the characteristic of certain pieces of information being deemed true, believed and justifiable, but rather a process. The sentences that reaches the status of knowledge forms a universe that provides an interpretation of the reality one aims to describe. Language exchanges information through communication and the justification, if concludes successfully with respect to a sentence, it elevates the information to the status of knowledge. We provide a model where we define the fundamental elements of communication and grammar. As a result, knowledge must be \open\ (everyone must be able to acquire it), \free\ (everyone must be able to justifiy) and \tidy\ (everyone must be able to retrace the justification process in all its parts recursively). Ultimately, the development of knowledge processing, referred to as \emph{knowmatic}, represents the evolution of the information technologies (\it).

Abstract Thyroid diseases have a complex and multifactorial aetiology. Despite the numerous studies on the signals referable to the malignant transition, still remain elusive the molecular mechanisms concerning the role of oxidative stress. Based on its strong oxidative power, H2O2 could be responsible for the high level of oxidative DNA damage observed in cancerous thyroid tissue and hyper-activation of mitogen-activated protein kinase (MAPK), and PI3K/Akt, that mediate ErbB signaling. Increased levels of 8-oxoG DNA adducts have been detected in the early stages of thyroid cancer. These DNA lesions are efficiently recognized and removed by the base excision repair (BER) pathway initiated by 8-oxoG glycosylase1 (OGG1). This study investigated the relationship between the EGFR and OGG1-BER pathways and their mutual regulation following oxidative stress stimulus by H2O2 in human thyrocytes. We clarified the modulation of ErbB receptors and their downstream pathways (PI3K / Akt and MAPK / ERK) under oxidative stress (from H2O2) at the level of gene and protein expression, according to the mechanism defined in a non-pathological cell system, Nthy-ori 3-1. Later, on the basis of the obtained results of gene expression cluster analysis in normal cells, we assessed the dysregulation of the relationships in a model of papillary thyroid cancer with RET/TPC rearrangement (TPC-1). Our observations demonstrated that a H2O2 stress may induce a physiological cross-regulation between ErbB and OGG1-BER pathways in normal thyroid cells (while this is dysregulated in the TPC-1 cells. Gene expression data also delineated that MUTYH gene could play a physiological role in cross-talk between ErbB and BER pathways and this function is instead lost in cancer cells. Overall our data about OGG1 protein expression suggest that the alternative splicing mechanisms may lead to different protein isoforms, physiologically regulated in response to ErbB modulation, and that these could be dysregulated in the progression of thyroid malignancies with RET/TPC rearrangement.

In recent years, bacterial resistance to conventional antibiotics has become a major concern in the medical field. The global misuse of antibiotics in clinics, personal use, and agriculture has accelerated this resistance, making infections increasingly difficult to treat and rendering new antibiotics ineffective more quickly. Finding new antibiotics is challenging due to the complexity of bacterial mechanisms, high costs and low financial incentives for the development of new molecular scaffolds, and stringent regulatory requirements. Additionally, innovation has slowed, with many new antibiotics being modifications of existing drugs rather than entirely new classes. Antimicrobial peptides (AMPs) are a valid alternative to small molecule antibiotics offering several advantages, including broad-spectrum activity and a lower likelihood of inducing resistance due to their multifaceted mechanisms of action. However, AMPs face challenges such as stability issues in physiological conditions, potential toxicity to human cells, high production costs, and difficulties in large-scale manufacturing. A reliable strategy to overcome the drawbacks associate with the use of small molecule antibiotics and AMPs is the combination therapy, namely the simultaneous co-administration of two or more antibiotics or the synthesis of covalently linked conjugates. This review is intended to cover and critically analyze the design, synthetic strategies, antibacterial activity and, when possible, the cytotoxicity of antibiotic-AMPs conjugates.

Bistatic radar experiments have been used to study surface characteristics of extra-terrestrial bodies in the Solar System, including the Moon, Venus, Mars, and Titan. This paper proposes a 3D model to characterize the scattered field of a Gaussian rough surface on an extra-terrestrial body for an orbital bistatic radar configuration. Specifically, this model will investigate how the variability of surface roughness impacts the spectral broadening of the received signal using physical optics approximations and ray tracing on a surface model using a facet approach with Gaussian properties. A linear relationship between spectral broadening of the signal and surface roughness was found. This relationship is in line with results obtained by commonly used analytical models for bistatic radar on planetary surfaces.

The reactivity of 3,5-di-(pyridin-4-yl)-1,2,4-thiadiazole (L1) with 1,4-diiodotetrafluorobenzene (1,4-DITFB) was explored and the halogen-bonded 1:1 co-crystal (1) was successfully isolated and structurally characterized.

Precipitation patterns are critical for understanding the hydrological and climatological dynamics of any region. Sicily, the largest island of the Mediterranean sea, with its diverse topography and climatic conditions, serves as an ideal case study for analyzing precipitation data to gain insights into regional water resources, agricultural productivity, and climate change impacts. This paper employs advanced statistical physics methods, particularly Tsallis q-statistics, to analyze sub-hourly precipitation data from 2002 to 2023, provided by the Sicilian Agrometeorological Informative System (SIAS). We investigate several critical variables related to rainfall events, including duration, depth, maximum record, and inter-event time. The study spans two decades (2002-2012 and 2013-2023), analyzing the distributions of relevant variables. Additionally, we examine the simple returns of these variables to identify significant temporal changes, fitting these returns with q-Gaussian distributions. Our findings reveal the scale-invariant nature of precipitation events, the presence of long-range interactions and memory effects, characteristic of complex environmental processes.

Uniform illumination is a key requirement in different research fields. However, this requirement is often difficult to achieve when high intensity is required at the same time. Recent advancements in LED lamps allow nowadays for compact and economical solutions. In this work we present a suitable solution for various laboratory purposes requiring stable, uniform and high intensity illumination. The system is composed of four identical high power white LED arrays of 30 mm diameter each, placed on a supporting and cooling structure having a minimum volume of 26 cm x 26 cm x 8 cm. A numerical model has been developed, based on a ray tracing software, in order to simulate the performances. These have then been experimentally validated with measurements of the power density map, carried out with a 1% uncertainty pyranometer. Data show that the built system is very stable over time and provides an illumination uniformity higher than 98%, on a surface of 50 mm radius, which reduces to 95% on a surface of 75 mm radius. The power density can be adjusted in the 390-1360 W m-2 range, not affecting uniformity.

The abilities of quantitative description of noise are restricted due to its origin and only the statistical and spectral analysis methods can be applied while an exact time evolution cannot be defined or predicted. It emphasizes the challenges faced in many applications including communication systems where noise can play, on one hand, a vital role impacting signal-to-noise ratio but possessing, on the other hand, unique properties such as infinite entropy (infinite information capacity), exponentially decaying correlation function and so on. Despite the deterministic nature of chaotic systems, the predictability of chaotic signals is limited for a short time window putting them close to random noise. In this article, we propose and experimentally verify an approach to achieve Gaussian-distributed chaotic signals by processing the outputs of chaotic systems. The mathematical criteria, on which the main idea of the study is based on, is the Central Limit Theorem which states that the sum of a large number of independent random variables with similar variances approaches a Gaussian distribution. The study involves more than 40 mostly three-dimensional continuous-time chaotic systems (Chua’s, Lorenz’s, Sprott’s, memristor-based, etc.) whose output signals are analyzed according to criteria that encompass the probability density functions of a chaotic signal itself and its envelope and phase, statistical and entropy-based metrics such as skewness, kurtosis, and entropy power. We found that two chaotic signals of Chua’s and Lorenz’s systems exhibited superior performance across the chosen metrics. Furthermore, our focus extended to determining the minimum number of independent chaotic signals necessary to yield a Gaussian-distributed combined signal. The analytic and experimental results indicate that the sum of at least three non-Gaussian chaotic signals closely approximates Gaussian distribution. It allows generation of reproducible Gaussian-distributed deterministic chaos by modeling simple chaotic systems.

Prolonged fatigue is associated with non-pathological causes, and lacks an established therapeutic approach. The current study is aimed at assessing the efficacy of a new food supplement (Improve® Response) based on a chemically characterized pomegranate extract and hydro-soluble vitamins (B complex and C). UHPLC-HRMS analysis of pomegranate extract showed the presence of 59 compounds, with gallotannins and ellagitannins being the most abundant phytochemicals. For the clinical study, 58 subjects were randomized into two groups, 1 and 2 (n = 29, each), which received either the food supplement or placebo. The effects of the food supplement against fatigue were assessed via validated questionnaires, recorded at time intervals t0 (at baseline), t1 (after 28 days), t2 (56 days), and t3 (after follow-up) in combination with the analysis of biochemical markers at t0 and t2. Fatigue Severity Scale (FSS) questionnaire scores were significantly decreased at the t2 and t3 time intervals in subjects treated with the food supplements, while the effect of the food supplement on a 12-Item Short Form Survey (SF-12) was not considerable. Moreover, the food supplement did not significantly affect biochemical parameters associated with fatigue and stressed conditions. This study shows that the food supplement tested reduces prolonged fatigue following two months supplementation in healthy subjects with mild prolonged fatigue.

Digital solutions in the field of restorative neurology offer significant assistance, enabling patients to engage in rehabilitation activities remotely. This research introduces ReMoVES, an Internet of Medical Things (IoMT) system delivering telemedicine services specifically tailored for Multiple Sclerosis rehabilitation, within the overarching framework of the STORMS project. The ReMoVES platform facilitates the provision of a rehabilitative exercise protocol, seamlessly integrated into the Individual Rehabilitation Project, curated by a multidimensional medical team operating remotely. This manuscript delves into the second phase of the study, elucidating the technology employed, the outcomes achieved, and the practical, professional, and academic implications. The STORMS initiative, as the genesis of digital telerehabilitation solutions, aims to enhance the quality of life for Multiple Sclerosis patients.

It is at the chemistry-biology interface that this work that we have carried out takes place. Indeed, the expected goal is to develop simple molecules, capable of activating the catalytic action of certain metalloenzymes such as tyrosinase. The official name of an enzyme includes the type of reaction catalyzed, the name of the substrates involved. In this work, we carried out the study of the catalytic activity of the complexes of organotin carboxylates synthesized vis-à-vis the oxidation of 3,5-di-tert-butylcatecchol. The results obtained show that the various complexes exhibit good catalytic activity for the oxidation of 3,5-di-tert-butylcatecchol under mild conditions. The complexes that showed good catalytic activity are the compounds C1 and C2.

Major depressive disorder (MDD) is a prevalent mental health condition with substantial social and economic consequences. This study focuses on the interplay between genetic and environmen-tal factors in MDD, with particular emphasis on epigenetic mechanisms such as stochastic epige-netic mutations (SEMs), epigenetic age acceleration, and epigenetic drift. We conducted a meta-analysis of DNA methylation patterns across six datasets (n=1125 MDD cases, 398 controls in whole blood; n=95 MDD cases, 96 controls in brain tissues) from the Gene Expression Omnibus. The analysis did not reveal significant global methylation differences between MDD cases and controls. However, a brain-specific probe (cg25801113) near the SHF gene consistently exhibited hypomethylation, suggesting its potential relevance to MDD. SEMs were assessed, revealing a dis-tinct burden at the gene level in MDD cases, though no significant findings emerged for epigenetic age acceleration, indicating it may not play a central role in MDD. The study also identified rare epivariations in specific genes unique to MDD cases. In blood tissue, 51 genes were associated with these unique epivariations, while 1 gene was highlighted in the brain tissue. These results un-derscore the importance of exploring rare epivariations in understanding the molecular mecha-nisms underlying MDD and offer potential targets for further investigation.

A Brewer Spent Grain (BSG), the most abundant by-product of the brewing process, is mainly used in animal feed and biogas production. The aim of the present work is BSG valorization by yeast fermentation to produce carotenoids. R. mucilaginosa CBS316 was cultured on BSG syrups, supplemented or not with YE and PEP (s-Fsa and Fsa). The biomass and carotenoid production were optimized in flasks and then scaled-up in bioreactor. In flask tests, the maximum biomass concentration was 5.3 and 6.2 g/L for Fsa and s-Fsa cultures, respectively. The maximum carotenoid production was 833 μg/L in Fsa and 1159 μg/L in s-FSA. Considering that the highest specific productivity value (P 7.16 μg/g*h) was obtained with Fsa syrup, this medium was selected for the process scale-up. In bioreactor tests, the maximum concentrations of biomass (4.29 g/L) and carotenoid (396 ug/L) was reached at 72 hours of fer-mentation, 24 h later than in flask. The total carotenoid produced was 524 and 150 ug in bioreactor and flask cultures, respectively. The carotenoids production by R. mucilaginosa was obtained both in Fsa and s-Fsa syrups. The results confirm the possibility to use the syrup as it is, Fsa, thus limiting the process costs.

CPPU (Forchlorfenuron (1-(2-chloropyridin-4-yl)-3-phenylurea), a synthetic cytokinin, is extensively used to enhance fruit size and quality size in several crops, including kiwifruit. This study examines the effects of three different CPPU application strategies on two different crop loads on the main fruit quality parameters. Our results show that a two application of CPPU significantly increased fruit weight, especially under standard crop load conditions, due to better resource allocation. Fruit firmness improved with 2 and 3-times CPPU applications, likely due to enhanced cell wall development, and was consistently affected by crop load, with higher loads resulting in softer fruits. CPPU applied twice did not significantly influence soluble solids content. This parameter was instead significantly influenced by the crop load, with standard load fruit showing higher sugar accumulation. Fruit dry weight showed similar trends, with CPPU having a more pronounced effect under standard crop loads. Overall, CPPU proved to be a cost-effective strategy to enhance fruit quality, particularly in orchards with standard crop loads, by balancing yield and sugar content.

In recent years, the global energy sector has seen significant transformation, particularly in Europe, with a notable increase in intermittent renewable energy integration. Italy and the European Union (EU) have been among the leaders in this transition, with renewables playing a substantial role in electricity generation as of mid-2020s. The adoption of Battery Energy Storage Systems (BESS) has become crucial for enhancing grid efficiency, sustainability, and reliability by addressing the intermittent renewable sources. This paper investigates the feasibility and economic viability of batteries into wholesale electricity markets as per EU regulation, focusing on the dynamics of very different markets, namely the Day-Ahead Market (DAM) based on system marginal price and the Cross-Border Intra-day Market (XBID) based on continuous trading. A novel model is proposed to enhance BESS operations, leveraging price arbitrage strategies based on zonal price predictions, levelized cost of storage (LCOS), and uncertain bid acceptance in continuous trading. Machine learning and deep learning techniques are applied for price forecasting and bid acceptance prediction, respectively. The study finds that data-driven techniques outperform reference models in price forecasting and bid acceptance prediction (+7-14% accuracy). Regarding market dynamics, the study reveals a higher competitiveness of the continuous market compared to the DAM, particularly with increased risk factor in bids leading to higher profits. This research provides insights into compatibility between continuous markets and BESS, showing substantial improvements in economic profitability and the correlation between risk and profits in the bidding strategy (+9 M€ yearly revenues are obtained with a strategic behavior that reduces by 60% awarded energy).

Stroke represents one of the neurological diseases most responsible for death and permanent disability in the world. Different factors, such as thrombus, emboli and atherosclerosis, take part in the intricate pathophysiology of stroke. Comprehending the molecular processes involved in this mechanism is crucial to developing new, specific and efficient treatments. Some common mechanisms are excitotoxicity and calcium overload, oxidative stress, and neuroinflammation. Furthermore, non-coding RNAs (ncRNAs) are critical in pathophysiology and recovery after cerebral ischaemia. ncRNAs, particularly microRNAs, and the long non-coding RNAs (lncRNAs) are essential for angiogenesis and neuroprotection, and they have been suggested to be therapeutic, diagnostic and prognostic tools in cerebrovascular diseases, including stroke. This review summarizes the intricate molecular mechanisms underlying ischemic and hemorrhagic stroke and delves into the function of miRNAs in the development of brain damage. Furthermore, we will analyze new perspectives on treatment based on molecular mechanisms in addition to traditional stroke therapies.

The persistence of symptoms following COVID-19 infection represents a significant challenge in healthcare management. During the outbreak, tele-rehabilitation emerged as a new tool to support healthcare structures in providing rehabilitation services. This study assessed the effectiveness and the feasibility of a 3-week home-based motor and respiratory rehabilitation program for long COVID-19 individuals after traditional rehabilitation. Twenty-three patients completed the program and underwent functional tests at different time points (i.e. baseline, after hospital discharge, and after tele-rehabilitation). Motor function was evaluated using the instrumented Six-Minutes Walking Test (i6MWT), with monitored heart rate and oxygen saturation. Conversely, respiratory function was measured via forced vital capacity (FVC) and maximal voluntary ventilation (MVV) tests. Significant improvements (p &lt; 0.05) in motor and respiratory function were observed throughout the intervention, including an 18.3% increase in walked distance from the baseline. The findings suggest that a home-based tele-rehabilitation can enhance motor and respiratory function in post-COVID patients. Despite limitations such as sample size and lack of control group, the positive outcomes seem to support the feasibility of the proposed tele-rehabilitation program in managing long COVID symptoms and promoting functional recovery. Further research is needed to validate these findings and explore tele-rehabilitation’s potential in broader patient populations.

After the ban on tributyltin-based antifouling paints, DCOIT (4,5-Dichloro-2-octylisothiazol-3(2H)-one) became one of the most used antifouling biocides. DCOIT is a pseudo-persistent contaminant in port areas and is toxic to non-target species, but its ability to bioaccumulate and be transferred along the trophic chain remains unknown. This study aimed to preliminarily investigate the bioaccumulation, trophic transfer, and biomagnification of DCOIT and SiNC-DCOIT (DCOIT immobilized in silica mesoporous nanocapsules) from the microalga Tetraselmis chuii to the mussel Mytilus galloprovincialis during exposure experiments considering 24 h of uptake followed by 72 h depuration. Mussels rapidly internalized and metabolized both DCOIT and SiNC-DCOIT. The predator-prey biomagnification factors (BMFTL) suggested that both forms of the biocide can be trophically transferred, with higher concentrations of DCOIT and SiNC-DCOIT in mussels than in microalgae (BMFTL &gt; 1). However, the bioaccumulation and bioconcentration factors indicated a low bioaccumulation capability in the short term, suggesting that the depuration rate overcomes the uptake. Our findings contribute to the development of environmental risk assessments for DCOIT and SiNC-DCOIT, but do not exclude the possibility of DCOIT bioaccumulation in the long-term in areas with constant input of DCOIT. Further studies are needed to understand these processes under continuous exposure scenarios to DCOIT.

Extracellular vesicles represent a large heterogeneous class of near and long-distance intercellular communication mediators, released by both prokaryotic and eukaryotic cells. Specifically, the scientific community has shown a growing interest in exosomes, which are nano-sized vesicles with an endosomal origin. Not so long ago, the physiological goal of exosome generation was largely unknown and required more investigation; at first, it was hypothesized that exosomes are able to remove excess, rejects and unnecessary constituents from cells to preserve cellular homeostasis. However, thanks to recent studies, the central role of exosomes in regulating cellular dialogue has emerged. Exosomes act as vectors on cell-cell signaling by their cargo, proteins, lipids, and nucleic acids, and influence physiological and pathological processes. The findings on exosomes are widespread in a large spectrum of biomedical applications from diagnosis and prognosis to thera-pies. In this review, we describe exosome biogenesis and the current methods for their isolation and characterization, emphasizing the role of their cargo in female reproductive processes, from gametogenesis to implantation, and the potential involvement in human female disorders.

The vascular endothelium is key target for immune, and thrombotic responses that has to be controlled in successful xenotransplantation. Several genes were identified that if induced or overexpressed help to regulate the inflammatory response and preserve the transplanted organ function and metabolism. However, few studies addressed combined expression of such genes. The aim of this work was to evaluate in vivo the effects of the simultaneous expression of a three human genes in a mouse generated using the multi-cistronic F2A technology. Male 3-month-old mice that express human heme oxygenase 1 (hHO-1), ecto-5’-nucleotidase (hE5NT), and ecto-nucleoside triphosphate diphosphohydrolase 1 (hENTPD1) (Transgenic) were compared to wild-type FVB mice (Control). Background analysis include extracellular nucleotide catabolism enzymes profile on the aortic surface, blood nucleotide concentration and serum L-arginine metabolites. Furthermore, inflammatory stress induced by LPS in transgenic and control mice was used to characterize interleukin 6 (IL-6) and adhesion molecules endothelium permeabil-ity responses. Transgenic mice had significantly higher rates of extracellular adenosine triphosphate and adenosine monophosphate hydrolysis on the aortic surface in comparison to control. Increased levels of blood AMP and adenosine were also noticed in transgenics. Moreover, transgenic ani-mals demonstrated the decrease in serum monomethyl-L-arginine level and a higher L-arginine/ monomethyl-L-arginine ratio. Importantly, significantly decreased serum IL-6, and adhesion mol-ecule levels were observed in transgenic mice in comparison to control after LPS treatment. Fur-thermore, reduced endothelial permeability in the LPS-treated transgenic mice was noted as com-pared to LPS-treated control. The human enzymes (hHO-1, hE5NT, hENTPD1) simultaneously encoded in transgenic mice demonstrated benefits in sev-eral biochemical and functional aspects of endothelium. This is consistent in use of this approach in the context of xenotransplantation.

The natural history of COVID-19 caused by SARS-CoV-2 is extremely variable, ranging from asymptomatic infection, to pneumonia, and to complications eventually fatal. We propose here the first model, explaining how the outcome of first, crucial 10-15 days after infection, hangs on the balance between the cumulative dose of viral exposure and the efficacy of the local innate immune response (natural IgA and IgM antibodies, MBL). If SARS-CoV-2 runs the blockade of this innate immunity and spreads from the upper airways to the alveoli in the early phases of the infections, it can replicate with no local resistance, causing pneumonia and releasing high amounts of antigens. The delayed and strong adaptive immune response (high affinity IgM and IgG antibodies) that follows, causes severe inflammation and triggers mediator cascades (complement, coagulation, and cytokine storm) leading to complications often requiring intensive therapy and being, in some patients, fatal. Strenuous exercise and high flow air in the incubation days and early stages of COVID-19, facilitates direct penetration of the virus to the lower airways and the alveoli, without impacting on the airway’s mucosae covered by neutralizing antibodies. This allows the virus to bypass the efficient immune barrier of the upper airways mucosa in young and healthy athletes. In conclusion, whether the virus or the adaptative immune response reach the lungs first, is a crucial factor deciding the fate of the patient. This “quantitative and time-sequence dependent” model has several implications for prevention, diagnosis, and therapy of COVID-19.

Taking due account of users' perspectives is crucial for improving the quality of healthcare services. This study aimed to analyse the representations and evaluation criteria that users of a public health agency express towards care and treatment services and to explore whether and how the content and meaning of their communications varied according to pre-pandemic, pandemic or post-pandemic periods. 501 communications (73.4% complaints, 16% appreciations, 10.6% enquiries) sent to the public relations office of an Italian health agency were collected. An automatic content analysis procedure (ACASM) was applied to the textual corpus. Four main thematic cores were identified concerning the request for care and respect, the value of the doctor-patient relationship and the difficulties in contacting services and accessing care. Two main latent dimensions of meaning were identified, which capture the dialectic between the demand for relationships and the demand for access to care, and between attention to the relational competence of health workers and attention to the needs and rights of users. Communications collected during the pre-pandemic and post-pandemic periods mainly concern the difficulty of access to care; those collected during the pandemic period mainly concern the doctor-patient relationship. Interpersonal aspects and timely access to care appear to be crucial in users' assessment of the quality of care.

Small bowel carcinomas (SBC) are uncommon neoplasms, whose predisposing conditions include hereditary syndromes and immune-mediated intestinal disorders, including coeliac disease (CD) and Crohn’s disease (CrD). Although both CD-associated SBC (CD-SBC) and CrD-associated SBC (CrD-SBC) arise from an inflammatory background, they differ substantially in tumour cell phenotype, frequency of microsatellite instability and nuclear β-catenin expression, as well as in prognosis. For these patients, high tumor-infiltrating lymphocyte density and glandular/medullary histotype represent independent positive prognostic factors. Dysplasia adjacent to SBC is rare and characterized by intestinal phenotype and nuclear β-catenin in CD, while it is frequent and typified by gastro-pancreatobiliary marker expression and preserved membranous β-catenin in CrD. Recent evidence suggests that Epstein-Barr virus-positive dysplasia and SBC, albeit exceptional, do exist and are associated with CrD. In this review we summarize the novel pathological and molecular insights of clinical and therapeutic interest to guide the care of CD-SBC and CrD-SBC.

Cardiovascular disease (CVD) is the leading cause of death worldwide. Cardiac rehabilitation (CR) has proven to be effective in reducing the rate of recurrence and disease as secondary prevention (evidence-based intervention) in patients who have suffered from myocardial infarction (MI). CR is a multidisciplinary path in which the patient is followed pharmacologically, from a psychological, nutritional, nursing and physiotherapy point of view. Post-MI patients present a reduction in the performance of the diaphragm muscle, the main inspiratory muscle, and this condition can become a risk factor for further relapses or for the onset of heart failure. Despite the solidity of the international guidelines for CR, the latter are lacking in specifically indicating an evaluation and training path regarding the inspiratory muscles in post-MI patients who have not undergone cardiac surgery. The article reviews the information on the adaptation of the diaphragm post-MI and highlights the need for clearer indications for a rehabilitation process that gives importance to the diaphragm.

Food-borne transmission is a recognized route for many viruses associated with gastrointestinal, hepatic or neurological diseases. Therefore, it is essential to identify new bioactive compounds with broad-spectrum antiviral activity is needed to exploit innovative solutions against these hazards. Lately, antimicrobial peptides (AMPs) have been recognized as promising antiviral agents. Indeed, while the antibacterial and antifungal effects of these molecules have been widely reported, their use as potential antiviral agents has not yet been fully investigated. Herein, the antiviral activity of previously identified or newly designed AMPs, was evaluated against the non-enveloped RNA viruses, Hepatitis A virus (HAV), and Murine Norovirus (MNV), a surrogate for human Norovirus. Moreover, specific assays were performed to recognize at which stage of the viral infection cycle the peptides could function. Results showed that almost all peptides displayed virucidal effects with about 90% of infectivity reduction on HAV or MNV. However, the decapeptide RiLK1 demonstrated, together with its antibacterial and antifungal properties, a notable reduction in viral infection for both HAV and MNV, possibly through direct interaction with viral particles or inhibition of the viral bonding to the cell receptors. Hence, RiLK1 could represent a versatile ‘antimicrobial agent effective against various foodborne pathogens including viruses, bacteria, and fungi.

This study explores advanced feature engineering and semantic enrichment methods to enhance text classification, focusing on detecting figurative language in tweets. The novel features introduced, Syno\_Lower\_Mean and Syn\_Mean, measure the use of uncommon synonyms and the mean frequency of synonyms, capturing semantic richness crucial for detecting figurative expressions. Using resources like SenticNet and Framester, we enrich our feature set with sentiment and frame semantic information. Our approach includes extensive data preprocessing, sophisticated feature selection, and implementing various classification models, such as SVM, KNN, Logistic Regression, Decision Trees, Random Forest, BERT, and LSTM networks. We rigorously evaluate each model's performance to assess the effectiveness of our features and enrichment methods. Putting emphasis on model explainability, we use decision tree analysis, feature importance analysis, and the TREPAN algorithm to approximate SVM decisions. Although we focus on figurative language detection, our methods have broader implications for various NLP text classification tasks. Our findings demonstrate significant improvements in classification accuracy and interpretability through innovative feature design and dataset enrichment.

The ovary is the major determinant of female reproductive health. Ovarian functions are mainly related to the primordial follicle pool, which is gradually loss with aging. Ovarian aging and reproductive dysfunctions share oxidative stress as common underlying mechanism. ROS signaling is essential for normal ovarian processes yet can contribute to various ovarian disorders when disrupted. Therefore, balance in the redox system is crucial for proper ovarian functions. In the present study, by focusing on mRNAs and ncRNAs described in the ovary and taking into account only validated ncRNA interactions, we built up an ovarian antioxidant ceRNA network, namely OvAnOx ceRNA, composed of 5 mRNAs (SOD1, SOD2, CAT, PRDX3, GR), 10 miRNAs and 5 lncRNAs (XIST, FGD5-AS1, MALAT1, NEAT1, SNHG1). Our bioinformatic analysis indicated that the components of the OvAnOx ceRNA not only contribute to antioxidant defence, but are also involved in other ovarian functions. Indeed, antioxidant enzymes encoded by mRNA of OvAnOx ceRNA operate within a regulatory network that impacts ovarian reserve, follicle dynamics, and oocyte maturation in normal and pathological conditions. The OvAnOx ceRNA represents a promising tool to unravel the complex dialogue between redox potential and ovarian signalling pathways involved in reproductive health, aging and diseases.

Inclusive education in Indonesia has evolved in recent years, in line with the government's commitment to provide equal education for all children, including those with special needs. This article reviews the philosophy of inclusive education and its implementation in Indonesian education. Through literature and policy analysis, it is found that although there is increasing awareness and support for inclusive education, there are still barriers that need to be overcome. These include the lack of accessibility and adequate facilities, limited teaching staff for children with special needs, and social stigma towards children with special needs. This review also identifies the characteristics of inclusive education and its implementation. In conclusion, inclusive education in Indonesia requires a holistic and collaborative approach between the government, communities, and educational institutions to create a truly inclusive and equal learning environment for all learners

Fungal-bacterial co-colonization and co-infections are emerging among TB-suspected patients, yet the underlying mechanisms that enable and arise from their interactions are poorly understood. Understanding how environmental microbes such as fungi and bacteria co-evolve and develop traits to evade host immune responses and resist treatment is critical to controlling opportunistic co-infections. Our previous work has demonstrated that fungal-bacterial interactions can have dramatic impacts on fungal pathogenesis and drug resistance. Here, we, therefore, hypothesize that cross-kingdom synergistic interactions between environmental fungi and bacteria may influence both fungal and bacterial virulence, antimicrobial resistance patterns and aetiology. Through this, we aimed to establish the prevalence of fungal–bacterial microbial communities associated with chronic primary or opportunistic pulmonary infections. Concordantly, through surveilling 302 clinical samples from 151 patients, we established the prevalence of TB (0.7%) to be lower than that of fungi (1.3%) and non-TB bacterial (4.6%) mono-aetiologies Figure 2. However, our main observation was the unexpected taxonomic diversity with a striking twist of fungal-bacterial di-kingdom aetiological conformities. Interestingly, the majority of the patients presented with at least a di or mono-kingdom aetiological pairings. Importantly, fungi and non-TB bacteria formerly regarded as atypical opportunists are now frequently isolated as possible aetiology for chronic pulmonary infection. Hence, we revealed many di-kingdom aetiological pairings here but their significance remains a question of further examination. Among which Acremonium spp + K. pneumoniae (n=5), Acremonium spp +Streptococcus pneumoniae (n=4), Acremonium spp + C. albicans + K. pneumoniae (n=3) were among the most dominant aetiological pairings observed. Interestingly, Acremonium spp + K. pneumoniae pairings were also seen to be the most commonly associated with pulmonary TB both during and after treatment. Isolation from the same infection niche as seen here calls for further investigations into any interaction signatures that may exist between these organisms. Taken together, our data suggest that fungal-bacterial co-existence may influence their virulence attributes and antimicrobial resistance patterns, with relevance to patient outcomes. Therefore, our data reveals an array of fungal-bacterial pairings that may influence the prognosis of chronic pulmonary disease. Importantly, suggesting that the diversity of pulmonary infective fungi and bacteria, and their complex population structures may pose challenges to the analysis and interpretation of conventional data. Thus, there is a need to redirect our diagnostic approaches to encompass polymicrobial aetiology in order to enhance our suspicion index for better management of opportunistic fungal-bacterial co-infections.

Despite available global efforts and funding, Tuberculosis (TB) continues to affect a considerable number of patients worldwide. Policy makers and stakeholders set clear goals to reduce TB incidence and mortality, but the emergence of multidrug-resistant TB (MDR-TB) and extensively drug-resistant TB (XDR-TB) complicate the reach of these goals. Drug-resistance TB needs to be diagnosed rapidly and accurately to effectively treat patients, prevent the transmission of MDR-TB, minimise mortality, reduce treatment costs and avoid unnecessary hospitalisations. In this narrative review, we provide a comprehensive overview of laboratory methods for detecting drug resistance in MTB, focusing on phenotypic, molecular and other drug susceptibility testing (DST) techniques. We found a large variety of methods used, with the BACTEC MGIT 960 being the most common phenotypic DST and the Xpert MTB/RIF being the most common molecular DST. We emphasise the importance of integrating phenotypic and molecular DST to address issues like resistance to new drugs, heteroresistance, mixed infections and low-level resistance mutations. Notably, most of the analysed studies adhered to the outdated definition of XDR-TB and did not consider the pre-XDR definition, thus posing challenges in aligning diagnostic methods with the current landscape of TB resistance.

The rationalization of single molecule magnets’ (SMMs) magnetic properties by quantum mechanical approaches represents a major task in the field of the Molecular Magnetism. The fundamental interpretative key of molecular magnetism is the phenomenological Spin Hamiltonian and the understanding of the role of its different terms by electronic structure calculations is expected to steer the rational design of new and more performing SMMs. This paper deals with the ab initio calculation of isotropic and anisotropic exchange contributions in the Fe(III) dimer [Fe₂(OCH₃)₂(dbm)₄]. This system represents the building block of one of the most studied Single Molecule Magnets ([Fe₄RC(CH₂O)₃)₂(dpm)₆] where R can be an aliphatic chain or a phenyl group just to name the most common functionalization groups) and its relatively reduced size allows the use of a high computational level of theory. Calculations were performed using CASSCF and NEVPT2 approaches on the X-ray geometry as assessment of the computational protocol, which has then be used to evinced the importance of the outer coordination shell nature through organic ligand modelization. Magneto-structural correlations as function of internal degrees of freedom for isotropic and anisotropic exchange contributions are also presented, outlining for the first time the extremely rapidly changing nature of the anisotropic exchange coupling.

Environmental contamination has exposed humans to various metal agents, including mercury. It has been determined that mercury is not only harmful to the health of vulnerable populations such as pregnant women and children, but is also toxic to ordinary adults in various ways. For many years, mercury was used in a wide variety of human activities. Nowadays, the exposure to this metal from both natural and artificial sources is significantly increasing. Recent studies suggest that chronic exposure, even to low concentration levels of mercury, can cause cardiovascular, reproductive and developmental toxicity, neurotoxicity, nephrotoxicity, immunotoxicity, and carcinogenicity. Possible biological effects of mercury, including the relationship between mercury toxicity and diseases of the cardiovascular system, such as hypertension, coronary heart disease and myocardial infarction, are being studied. As heart rhythm and function are under autonomic nervous system control, it has been hypothesized that the neurotoxic effects of mercury might also impact cardiac autonomic function. Mercury exposure could have a long-lasting effect on cardiac parasympathetic activity and some evidence show that mercury exposure might affect heart rate variability, particularly early exposures in children. The mechanism by which mercury produces toxic effects on the cardiovascular system is not fully elucidated, but this mechanism is believed to involve an increase in oxidative stress. The exposure to mercury increases the production of free radicals, potentially because of the role of mercury in the Fenton reaction and a reduction in the activity of antioxidant enzymes, such as glutathione peroxidase. In this review we report an overview on the toxicity of mercury and focus our attention on the toxic effects on the cardiovascular system.

Several cities are experiencing an increase in flood hazard and exposure, and consequentially in flood risk, attributable to the coupled effect of climate change and urbanization. Non-structural protection strategies demonstrate significant potential in the short term for mitigating hydraulic risk in urban areas, particularly where the implementation of structural measures is impeded by a complex urban environment. This work proposes an Early Warning System (EWS) for fluvial floods developed for the city of Palermo (Italy). It is based on the preliminary definition of po-tential Flood Event Scenarios (FESs) as a function of typical potential precursors. Each FES pre-dicts first points of flooding, flood areas and water depths, also providing specific hazard maps for people, vehicles, and buildings. The EWS uses rainfall depth-duration thresholds to assess the expected hydrograph as a function of rainfall forecasts and the water stage observed in real time at an upstream section of the river crossing the city. This last also allows for estimating the ante-cedent wetness conditions. Based on this information, the EWS retrieves an expected FES from a pre-built library with a preannouncement time up to 36 h. The EWS is here successfully tested on a historical flood event.

The study of rare diseases is important not only for the individuals affected but also for the advancement of medical knowledge and a deeper understanding of human biology and genetics. The wide repertoire of structural information now available from reliable and accurate prediction methods provides the opportunity to investigate the molecular origins of most of the rare diseases reviewed in the Orpha.net database. Thus, it has been possible to analyze the topology of the missense mutations found in the 2,535 proteins involved in Mendelian rare diseases (MRD), which form the database for our structural bioinformatics study. The amino acid substitutions responsible for MRD show different mutation site distributions at different three-dimensional protein depths. We then predicted the depth-dependent effects of mutations for the 20,248 pathogenic variants that are present in our database. The results of this structural bioinformatics investigation are relevant, as they provide additional clues to mitigate the damage caused by MRD.

Coronavirus disease 2019 (COVID-19) displays clinical heterogeneity, but little information is available for patients with mild or very early disease. We aimed to characterize biomarkers that are useful in discriminating the hospitalization risk in a COVID-19 cohort from Northern Italy during the first pandemic wave. We enrolled and followed for four weeks 76 symptomatic SARS-CoV-2 positive patients and age/sex-matched healthy controls. Patients with mild disease were discharged (n.42), and the remaining were hospitalized (n.34). Blood was collected before any anti-inflammatory/immunosuppressive therapy and assessed for soluble C5b-9/C5a, H3-neutrophil extracellular traps (NET), calprotectin, DNase plasma levels by ELISA, and a panel of pro-inflammatory cytokines by ELLA. Calprotectin and NET levels discriminate between hospitalized and non-hospitalized patients, while DNase negatively correlates with NET levels; there are positive correlations between calprotectin and both NET and neopterin levels. Neopterin levels increase in patients at the beginning of the disease and more in hospitalized than non-hospitalized ones. C5a and sC5b-9, and other acute phase proteins correlate with neopterin, calprotectin, and DNase. Both NET and neopterin levels negatively correlate with platelet count. We show that calprotectin, NET, and neopterin are important proinflammatory parameters potentially useful in discriminating between COVID-19 patients at risk for hospitalization.