To solve the problem of smooth switching between car-following model and lane-changing model, the Intelligent Driver Model (IDM) for a single lane was used to study the driver's behavior switching mechanism of normally following, generating intentions to change lanes, creating space and speed gains, and performing lane change. In the case of sufficient lane-changing space and speed gains, the ego vehicle's intention to change lane was considered to solve the switching boundary between car-following behavior and lane-changing behavior, which is also the IDM failure point. In the event that there is no lane-changing gains, the IDM was optimized by incorporating the constraint components of the target lane vehicles in conjunction with the actual motion state of the ego vehicle, and the Stepless Switching Intelligent Driver Model (SSIDM) was constructed. Drivers' natural driving information was collected and scenario mining was performed on structured roads. On the basis of the collected data, an elliptic equation was used to fit the behavior switching boundary, and the two component balance coefficients of the front and rear vehicles on the target lane were identified. According to the test set verification results, the Mean Square Error (MSE) of the SSIDM is 2.172, which is 57.98% less than that of the conventional single-lane IDM. The SSIDM can accomplish stepless switching comparable to driver's behavior between the car-following behavior and the lane-changing behavior, with greater precision than IDM.

A macro network loading Model for multi-flow lines, time-varying and pedestrian congestion is proposed. The station hub is abstracted as a network of different types of nodes, and the flow of passengers at each node is calculated in real time for the purpose of simulating the hub's collection and distribution process. For correct transmission of passenger flow on heterogeneous networks, three types of indexes are proposed to distinguish the nodes, and then match the corresponding fundamental diagrams. This paper divides the update process of the dynamic network loading model into multiple processes by flow lines, and improves computational speed of DNL model. The proposed model is applied to the simulation of passenger flow collection and distribution in an actual hub station with multi-flow lines. The analysis results illustrate that the model can accurately reflect the realistic congestion facilities and explain the formation process of high-density areas. A rolling passenger flow control model based on optimal control theory is proposed. The effectiveness of the control model is verified based on simulation data.

Objective: To use the ancient and modern medical record cloud platform (V2.3.5) to organize and explore the medication patterns of the "Three Causes, Extremity, and One Disease Syndrome Formula" by Chen Wuxuan, and to summarize its therapeutic ideas. Method: Collect and organize the "San Yin Si Tian Fang" in the "San Yin Ji Yi Zheng Fang Lun", and use the modern medical record cloud platform (V2.3.5) to conduct medication frequency statistical analysis, cluster analysis, and complex network analysis. As a result, a total of 16 Chinese herbal medicines were collected in the "Three Causes, Extreme and One Disease Syndrome Formula", involving 75 traditional Chinese medicines. Statistical analysis showed that roasted licorice was the most commonly used, followed by Pinellia ternata, papaya, ginger, and Poria cocos; Medications mainly include warm drugs, sweet and pungent flavors, as well as drugs that promote lung and spleen meridians. Cluster analysis can divide the above-mentioned traditional Chinese medicine into two groups, with specific grouping as follows. Group 1: ginger, white peony, aconite, papaya, and achyranthes bidentata; Group 2: roasted licorice, poria cocos, dried ginger, pinellia ternata, and green peel. Conclusion: The characteristics of the 16 prescriptions are biased towards Xin Gan Wen, emphasizing the regulation of the spleen and stomach, which may be related to the common use of prescription by doctors in the Song Dynasty and the tendency towards warm and dry medication.

In the present study, an attempt was made to induce rooting from single-node cuttings of hybrid aspen (Populus tremula L. ×P. tremuloides Michx.) with different concentrations of IAA, IBA and NAA during rooting. Among the three auxins used, NAA showed more effective induction on rooting as compared to IAA and IBA at the whole level. Thereafter, NAA was used further in experiments for anatomical and biochemical investigation. The results showed that it took 12 days from the differentiation of primordium to the appearance of young adventitious roots with NAA application. It was found that endogenous IAA, ZR and GA3 levels increased, but ABA decreased in cuttings with 0.54 mM NAA treatment. In contrast to the endogenous IAA level, NAA had negative effect on IAA-oxidase (IAAO) activity. Similarly, the decreased peroxidase (POD) activity, consistent with down-regulation of expressed levels of POD1 and POD2, was observed in NAA-treated cuttings. Whereas, NAA resulted in a higher activity in polyphenol oxidase (PPO) compared to the control cuttings. Collectively, the study highlighted that 0.54 mM NAA is efficient on rooting in hybrid aspen, and its effect on metabolic changes during rooting is discussed, which provide valuable information for propagating hybrid aspen.

Glioblastoma (GBM) is the most common malignant brain tumor in adults. Despite advancements in treatment, the prognosis for patients with GBM remains poor due to its aggressive nature and resistance to therapy. CRISPR-based genetic screening has emerged as a powerful tool for identifying genes crucial for tumor progression and treatment resistance, offering promising targets for tumor therapy. In this review, we provide an overview of the recent advancements in CRISPR-based genetic screening approaches and their applications in GBM. We highlight how these approaches have been used to uncover genetic determinants of GBM progression and susceptibility to various therapies. Furthermore, we discuss ongoing challenges and future directions of CRISPR-based screening methods in advancing GBM research.

Infrared thermography has already been proven to be a significant method in non-destructive evaluation since it gives information with immediacy, rapidity and low cost. However, the thorniest issue for wider application of IRT is the quantification. In this work, we proposed a specific depth quantifying technique by employing the Gated Recurrent Units (GRU) in composite material samples via pulsed thermography (PT). Carbon Fiber Reinforced Polymer(CFRP) embedded with flat bottom holes were designed via Finite Element Method (FEM) modeling in order to precisely control the depth and geometrics of the defects. The GRU model automatically quantified the depth of defects presented in the CFRP material. The proposed method evaluated the accuracy and performance of synthetic CFRP data from FEM for defect depth predictions.

We consider partition functions, in the form of state sums, and associated probabilistic measures for aperiodic substrates described by model sets and their associated tiling spaces. We propose model set tiling spaces as microscopic models for small scales in the context of quantum gravity. Model sets possess special self-similarity properties that allow us to consider implications on large and observable scales from the underlying (non-ergodic) dynamics. In particular we consider the implication of the underlying aperiodic substrate for the well known problem of time in quantum gravity, and propose a correspondence between small and large scales, the so-called ergodic correspondence, that addresses the emergence of matter properties and spacetime structure. In the process we find a possible bound in the mass spectrum of fundamental particles.

Since the implementation of the Materials Genome Project by the Obama administration in the United States, the development of various computational materials databases has fundamentally expanded the choices of industries such as materials and energy. In the field of thermoelectric materials, the thermoelectric figure of merit ZT quantifies the performance of the material. From the viewpoint of calculations for vast materials, the ZT values are not easily obtained due to their computational complexity. Here, we show how to build a database of thermoelectric materials based on first-principles calculations for the electronic and heat transport of materials. Firstly, the initial structures are classified according to the values of bandgap and other basic properties using the clustering algorithm K-means in machine learning, and high-throughput first principles calculations are carried out for narrow-bandgap semiconductors which exhibiting potential thermoelectric application. The present framework of calculations mainly includes deformation potential module, electrical transport performance module, mechanical and thermodynamic properties module. We have also set up a search webpage for the calculated database of thermoelectric materials, providing searching and viewing the related physical properties of materials. Our work may inspire the construction of more computational databases of first-principle thermoelectric materials and accelerate research progress in the field of thermoelectrics.

This paper presents a review on numerical and experimental methods to predict fracture of ad-vanced high strength steels (AHSS). AHSS are widely processed through sheet metal forming processes. Although being an excellent choice when lightweight, high strength and ductility are critical factors, their multi-phase microstructure accentuates forming challenges. To accurately model forming behavior, necking based failure criteria as well as direct fracture models require improvements. As a necking based failure model, the conventional forming limit diagram/curve (FLD/FLC) presents limitations such as in estimating direct fracture (surface cracks, edge cracks, shear cracks), as well as deformation histories under nonlinear strain paths. Thus, significant re-search efforts are being made towards the needs of advanced fracture constitutive models capa-ble of predicting fracture scenarios without necking, more frequently observed in the realm of AHSS. Scientific community research is divided into several directions aiming at improving the forming and fracture behavior accuracy of parts subjected to sheet metal forming operations. In this review paper, a comprehensive overview on ductile fracture modeling is presented. Firstly, the FLD/FLC limitations modeling fracture behavior in sheet metal forming operations are stud-ied. Followed by the recent trends in constitutive material modeling. Afterwards, material char-acterization methods advancements to cover a broad range of stress states are comprised. Final-ly, damage and fracture models predicting failure in AHSS are investigated. This review paper supplies relevant information on the current issues the sheet metal forming community is chal-lenged with due to the trend towards AHSS employment in the automotive industry.

The current management of colorectal cancer liver metastasis (CRCLM) patients involves a multidisciplinary approach with surgical resection remaining the primary curative option. The advances in liver surgery have improved outcomes, enabling more patients to undergo surgery successfully. In addition, the development of imaging software has improved the preoperative planning and patient selection for surgery and other interventions. Systemic therapies, such as targeted therapies and immunotherapies have enhanced the chances of complete resection. Targeted agents in combination with chemotherapy, have shown efficacy in downstaging tumors and increasing resectability.

It is shown how the secondary structure of proteins, musical forms and verses of poems are approximately ruled by universal laws relying on graph coverings. In this direction, one explores the group structure of a variant of the SARS-Cov-2 spike protein and the group structure of apolipoprotein-H, passing from the primary code with amino acids to the secondary structures organizing the foldings. Then one look at the musical forms employed in the classical and contemporary periods. Finally, one investigates in much detail the group structure of a small poem in prose by Charles Baudelaire and that of the Bateau Ivre by Arthur Rimbaud.

Every protein consists of a linear sequence over an alphabet of $20$ letters/amino acids. The sequence unfolds in the $3$-dimensional space through secondary (local foldings), tertiary (bonds) and quaternary (disjoint multiple) structures. The mere existence of the genetic code for the $20$ letters of the linear chain could be predicted with the (informationally complete) irreducible characters of the finite group $G_n:=\mathbb{Z}_n \rtimes 2O$ (with $n=5$ or $7$ and $2O$ the binary octahedral group) in our previous two papers. It turns out that some quaternary structures of protein complexes display $n$-fold symmetries. We propose an approach of secondary structures based on free group theory. Our results are compared to other approaches of predicting secondary structures of proteins in terms of $\alpha$ helices, $\beta$ sheets and coils, or more refined techniques. It is shown that the secondary structure of proteins shows similarities to the structure of some hyperbolic $3$-manifolds. The hyperbolic $3$-manifold of smallest volume --Gieseking manifold--, some other $3$ manifolds and the oriented hypercartographic group are singled out as tentative models of such secondary structures. For the quaternary structure, there are links to the Kummer surface.

Taking a DNA-sequence, a word with letters/bases A, T, G and C, as the relation between the generators of an infinite group $\pi$, one can discriminate two important families: (i) the cardinality structure for conjugacy classes of subgroups of $\pi$ is that of a free group on $1$ to $4$ bases and the DNA word, viewed as a substitution sequence, is aperiodic. (ii) The cardinality structure for conjugacy classes of subgroups of $\pi$ is not that of a free group, the sequence is generally not aperiodic and topological properties of $\pi$ have to be determined differently. The two cases rely on DNA conformations such as A-DNA, B-DNA, Z-DNA, G-quadruplexes, etc. We found a few salient results: Z-DNA, when involved in transcription, replication and regulation in a healthy situation implies (i). The sequence of telomeric repeats comprising $3$ distinct bases, most of the time, satisfies (i). For $2$-base sequences in the free case (i) or non free case (ii), the topology of $\pi$ may be found in terms of the $SL(2,\mathbb{C})$ character variety of $\pi$ and the attached algebraic surfaces. The linking of two unknotted curves --the Hopf link-- may occur in the topology of $\pi$ in cases of biological importance, in telomeres, G-quadruplexes, hairpins and junctions, a feature we already found in the context of models of topological quantum computing. For $3$- and $4$ base sequences, other knotting configurations are noticed and a building block of the topology is the $4$-punctured sphere. Our methods have the potential to discriminate potential diseases associated to the sequences.

This work continues the review and illustrative application to energy systems of the “Fourth-Order Best-Estimate Results with Reduced Uncertainties Predictive Modeling” (4th-BERRU-PM) methodology. The 4th-BERRU-PM methodology uses the Maximum Entropy (MaxEnt) principle to incorporate fourth-order experimental and computational information, in-cluding fourth (and higher) order sensitivities of computed model responses with respect to model parameters. The 4th-BERRU-PM methodology yields the fourth-order MaxEnt posterior distribution of experimentally measured and computed model responses and parameters, in the combined phase-space of model responses and parameters. The 4th-BERRU-PM methodology encompasses fourth-order sensitivity analysis (SA) and uncertainty quantification (UQ), which were reviewed in the accompanying work (Part 1), as well as fourth-order data assimilation (DA) and model calibration (MC) capabilities, which will be reviewed and illustrated in this work (Part 2). The applicability of the 4th-BERRU-PM methodology to energy systems is illustrated by using the Polyethylene-Reflected Plutonium (acronym: PERP) OECD/NEA reactor physics benchmark, which is modeled using the linear neutron transport Boltzmann equation, involving 21976 im-precisely known parameters. This benchmark is representative of “large-scale computations” such as those involved in the modeling of energy systems. The result (“response”) of interest for the PERP benchmark is the leakage of neutrons through the outer surface of this spherical benchmark, which can be computed numerically and measured experimentally. The impact of the high-order sensitivities of the response with respect to the PERP model parameters is quantified for “high-precision” parameters (2% standard deviations) and “medium-precision” parameters (5% standard deviations). Analyzing the best-estimate results with reduced uncertainties for the 1st- through 4th-order moments (mean values, covariance, skewness, and kurtosis) produced by the 4th-BERRU-PM methodology for the PERP benchmark indicates that, even for systems mod-eled by linear equations (e.g., the PERP benchmark), retaining only first-order sensitivities is insufficient for reliable predictive modeling (including SA, UQ, DA, MC). At least second-order sensitivities should be retained in order to obtain reliable predictions.

Our recent work has focused on the application of infinite group theory and related algebraic geometric tools in the context of transcription factors and microRNAs. We were able to differentiate between “healthy" nucleotide sequences and disrupted sequences that may be associated with various diseases. In this paper, we extend our efforts to the study of messenger RNA metabolism, showcasing the power of our approach. We investigate (i) mRNA translation in prokaryotes and eukaryotes, (ii) polyadenylation in eukaryotes, which is crucial for nuclear export, translation, stability, and splicing of mRNA, (iii) miRNAs involved in RNA silencing and post-transcriptional regulation of gene expression, and (iv) the identification of disrupted sequences that could lead to potential illnesses. To achieve this, we employ (a) infinite (finitely generated) groups fp, with generators representing the r+1 distinct nucleotides and a relation between them [e.g., the consensus sequence in the mRNA translation (i), the poly(A) tail in item (ii), and the miRNA seed in item (iii)], (b) aperiodicity theory, which connects “healthy groups" fp to free groups Fr of rank r and their profinite completion F^r, and (c) the representation theory of groups fp over the space-time-spin group SL2(C), highlighting the role of surfaces with isolated singularities in the character variety. Our approach could potentially contribute to the understanding of the molecular mechanisms underlying various diseases and help develop new diagnostic or therapeutic strategies.

Broadband reverse saturable absorption is systematically investigated via Z-scan, transient absorption spectrum (TAS). The excited state absorption and negative refraction of Orange IV are observed in the Z-scan experiment at 532 nm. Meanwhile, two-photon induced excited-state absorption and pure two-photon absorption are observed at 600 nm and 700 nm with the pulse width of 190 fs, respectively. An ultrafast broadband absorption in visible wavelength region is observed via TAS. The different nonlinear absorption mechanism at multiple wavelengths is discussed and interpreted from the results of TAS. In addition, the ultrafast dynamics of negative refraction in the excited state of Orange IV is investigated via degenerate phase object pump probe, from which the weak long-lived excited state is extracted. All studies indicate that Orange IV has the potential to be further optimized into a superior broadband reverse saturable absorption material and also has certain reference significance for the study of optical nonlinearity in organic molecules containing azobenzene groups.

The major histocompatibility complex (MHC) genes are the most polymorphic genes in vertebrates, and their proteins play a critical role in adaptive immunity for defense against a variety of pathogens. MHC diversity was lost in many species after experiencing a decline in size. To understand the variation and evolution of MHC genes in the Siberian ibex, Capra sibirica, which has undergone a population decline, we analyzed the variation of the second exon of MHC class II DRB genes in samples collected from five geographic localities in Xinjiang, China, that belong to three diverged mitochondrial clades. Consequently, we identified a total of 26 putative functional alleles (PFAs) with 260 bp in length from 43 individuals, and found one (for 27 individuals) to three (for 5 individuals) PFAs per individual, indicating the presence of one or two DRB loci per haploid genome. The Casi-DRB1*16 was the most frequently occurring PFA, Casi-DRB1*22 came after found in only seven individuals, 14 PFAs occurred once (7 PFAs twice), implying high frequency of rare PFAs. Interestingly, more than half of the (15) PFAs were specific to clade I, only one and three PFAs were specific to clades II and III, respectively. So, we assume that the polygamy and sextual segregation nature of this species likely contributed to the allelic diversity of DRB genes. Genetic diversity indices showed that PFAs of clade II were lower in nucleotide, amino acid, and supertype diversity compared to those of the other two clades. The way of allele sharing and FST values between three clades were to some extent in agreement with pattern observed in mitochondrial DNA divergence. In addition, recombination analyses revealed no evidence for significant signatures of recombination events. Alleles shared by clades III and the other two clades diverged 6 million years ago, and systematic neighbor grids showed cross-species polymorphisms. Together with the PAML and MEME analyses, the results indicated that the DRB gene in C. sibirica evolved under balancing and positive selection. However, by comparison, it can be clearly seen that different populations were under different selective pressures. Our results are valuable in understanding the diversity and evolution of the DRB gene in a mountain living C. sibirica and in making decisions on future long-term protection strategies.

Transcription factors (TFs) are proteins that recognize specific DNA fragments in order to decode the genome and ensure its optimal functioning. TFs work at the local and global scales by specifying cell type, cell growth and death, cell migration, organization and timely tasks. We investigate the structure of DNA-binding motifs with the theory of finitely generated groups. The DNA ‘word’ in the binding domain -the motif- may be seen as the generator of a finitely generated group Fdna on four letters, the bases A, T, G and C. It is shown that, most of the time, the DNA-binding motifs have subgroup structure close to free groups of rank three or less, a property that we call ‘syntactical freedom’. Such a property is associated to the aperiodicity of the motif when it is seen as a substitution sequence. Examples are provided for the major families of TFs such as leucine zipper factors, zinc finger factors, homeo-domain factors, etc. We also discuss the exceptions to the existence of such a DNA syntactical rule and their functional role. This includes the TATA box in the promoter region of some genes, the single nucleotide markers (SNP) and the motifs of some genes of ubiquitous role in transcription and regulation.

Nowadays, unmanned vehicles are widely used in various fields. However, the safety of unmanned vehicles is directly determined by the autopilot systems, and sensor faults are a very critical factor that affects the normal operation of the autopilot systems. To efficiently and comprehensively test unmanned systems for sensor faults, this paper proposes a chip-level testing platform for unmanned vehicle autopilot systems based on FPGA hardware-in-the-loop simulation. Unlike existing testing platforms, the introduction of FPGA technology allows us to achieve nanosecond real-time simulation frequency, thus realizing chip-level simulation of sensors and black-box automated testing. Firstly, we propose a set of general platform and modeling methods, and the paper presents a detailed application of the four most common necessary sensors in autopilot systems as examples. Secondly, we propose for the first time a chip-level fault testing method for unmanned systems, and build a test platform with a quadrotor vehicle, the PX4 software platform, and the Pixhawk4 hardware platform as examples. Finally, the experimental results verify that the testing platform proposed in this paper can adapt to various autopilot systems and has high simulation test reliability.

It is shown that the representation theory of some finitely presented groups thanks to their $SL_2(\mathbb{C})$ character variety is related to algebraic surfaces. We make use of the Enriques-Kodaira classification of algebraic surfaces and the related topological tools to make such surfaces explicit. We study the connection of $SL_2(\mathbb{C})$ character varieties to topological quantum computing (TQC) as an alternative to the concept of anyons. The Hopf link $H$, whose character variety is a Del Pezzo surface $f_H$ (the trace of the commutator), is the kernel of our view of TQC. Qutrit and two-qubit magic state computing, derived from the trefoil knot in our previous work, may be seen as TQC from the Hopf link. The character variety of some two-generator Bianchi groups as well as that of the fundamental group for the singular fibers $\tilde{E}_6$ and $\tilde{D}_4$ contain $f_H$. A surface birationally equivalent to a $K_3$ surface is another compound of their character varieties.

The Kummer surface was constructed in 1864. It corresponds to the desingularisation of the quotient of a 4-torus by 16 complex double points. Kummer surface is kwown to play a role in some models of quantum gravity. Following our recent model of the DNA genetic code based on the irreducible characters of the finite group G5:=(240,105)≅Z5⋊2O (with 2O the binary octahedral group), we now find that groups G6:=(288,69)≅Z6⋊2O and G7:=(336,118)≅Z7⋊2O can be used as models of the symmetries in hexamer and heptamer proteins playing a vital role for some biological functions. Groups G6 and G7 are found to involve the Kummer surface in the structure of their character table. An analogy between quantum gravity and DNA/RNA packings is suggested.

In light of the self-simulation hypothesis, a simple form implementation of the principle of efficient language is discussed in a self-referential geometric quasicrystalline state sum model in three dimensions. Emergence is discussed in context of geometric state sum models.

Cultivated land plays an important role in water and soil loss in the earth-rocky mountainous region, northern China, however, its responses to soil control measures and rainfall characteristics are still not fully understood. In this study, 85 erosive rainfall events in 2011-2019 were grouped into three types, and the responses of runoff and soil loss on five cultivated plots with different slopes in the upstream catchment of the Miyun Reservoir to soil conservation measures and rainfall regimes were evaluated. Results found that event-averaged runoff depths and soil loss rates on the five plots ranged from 7.05 mm to 0.03 mm and from 300.51 t km-2 to 0.37 t km-2 respectively, depending on rainfall regimes, soil conservation measures, and slope gradients. The high occurring frequency (i.e., 72.94%) rainfall regime A with short rainfall duration (RD), low rainfall amount (P), and high mean rainfall intensity (Im) yielded lower runoff depth and higher soil loss rate. Rainfall regime B with longer RD, and higher P and Im, however, produced higher rainfall depth and lower soil loss rate. Terraced plot had the highest runoff and soil loss reduction efficiencies of over 96.03%. Contour tillage had comparable sediment reduction efficiency to that of the terraced plot on gentle slopes (gradient less than 11.0%), while its runoff reduction efficiency was less than 13.11%. This study implies that in the Miyun Reservoir catchment and similar regions in the world, contour tillage should be promoted on gentle slopes, and terrace construction should be given enough attention since it can greatly reduce water quantity and cause water shortage in downstream catchments.

As Artificial Intelligence (AI) technology, particularly Machine Learning algorithms, becomes increasingly ubiquitous, our abilities to understand and interpret AI and machine learning algorithms are becoming increasingly desirable. Visualization has been used as a common tool to view and understand complex machine learning processes. In this paper, we will focus on developing a general framework for the visualization of machine learning models as a scalar valued multi-dimensional function to help users understand how the models behave over different viewing spaces. We first give a formal definition of the visualization problem. Interpolation-based morphing and subspace sampling techniques are applied to generate various renderings through projections and cross-sections of the model space as 3D surfaces or heatmap images. This method will be applied to two real-world datasets and applications: the diagnosis of Alzheimer's Disease (AD) using a human brain networks dataset and a real-world benchmark dataset for predicting home credit default risks. The visualizations show that different machine learning algorithms can behave quite differently under different conditions.

In this paper, a new axial-type magnetic gear with auxiliary flux-enhancing structure (AFS-AMG) is proposed. Compared to conventional AFS-AMG, it has the higher torque density and higher permanent magnet (PM) utilization factor. Firstly, the design rules and operating principles of proposed AFS-AMG are elaborated. Then, the mapping relation between the radial-type magnetic gears (RMGs) and AMGs are elucidated. Compared to its counterpart in RMGs, AFS-AMGs achieve small size. Then, the geometrical parameters of AFS-AMGs are optimized to obtain the better electromagnetic performances, where the torque density per volume and per PM volume is adopted as the evaluation standard. Finally, three different AMG topologies are constructed in finite element analysis (FEA) software for comparison. It is proven that the AFS-AMG has the largest torque density per volume and per PM volume.

Open-vocabulary learning has recently gained prominence as a means to enable image segmentation for arbitrary categories based on textual descriptions. This advancement has extended the applicability of segmentation systems to a broader range of generally purpose scenarios. However, current methods often revolve around specialized architectures and parameters tailored to specific segmentation tasks, resulting in a fragmented landscape of segmentation models. In response to these challenges, we introduce OVAMTSeg, a versatile framework designed for Open-Vocabulary and Multitask Image Segmentation. OVAMTSeg harnesses adaptive prompt learning to empower the model to capture category-sensitive concepts, enhancing its robustness across diverse multi-task and scenario contexts. Text prompts are employed to effectively capture semantic and contextual features of the text, while cross-attention and cross-modal interactions enable the fusion of image and text features. Furthermore, a transformer-based decoder is incorporated for dense prediction. Extensive experimental results underscore the effectiveness of OVAMTSeg, showcasing its state-of-the-art performance and superior generalization capabilities across three segmentation tasks. Notable achievements include a 47.5 mIoU in referring expression segmentation, 51.6 mIoU on Pascal-VOC with four unseen classes, 46.6 mIoU on Pascal-Context in zero-shot segmentation, 65.9 mIoU on Pascal-5i, and 35.7 mIoU on COCO-20i datasets for one-shot segmentation.

In recent years, nocturnal ozone enhancement(NOE) events have become a hot research topic in the field of atmospheric environment. By using statistically-based data analysis, we made a comparative investigation about nocturnal ozone concentrations and NOE events in 2022 and 2023, and further explored the effects of NOE events on O3 and PM2.5 at the night of the same day and the next day. The results showed that from 2022 to 2023 in Dongying, the annual average nocturnal ozone concentrations increased from 51 μg/m3 to 59 μg/m3, and the frequency of NOE events was higher in spring, summer and autumn, and lower in winter. NOE events not only had an obvious promoting effect on nocturnal O3 and Ox, and the daily maximum 8 h average concentration of O3 (MDA8-O3) of the same day (more apparent in summer and autumn), and nocturnal PM2.5 and PM2.5-bounded NO3- and SO42- (more apparent in winter), but also had a distinct influence on O3, Ox and MDA8-O3 of the next day (more apparent in summer). The results could strengthen the understanding of the phenomena of NOE events, and provide a scientific basis for the collaborative control of PM2.5 and ozone in urban areas in the Yellow River Delta, China.

We constrain two dynamical dark energy models that are parametrized by the logarithm form of $w(z)=w_{0}+w_{1}\left(\frac{\ln (2+z)}{1+z}-\ln 2\right)$ and the oscillating form of $w(z)=w_{0}+w_{1}\left(\frac{\sin(1+z)}{1+z}-\sin(1)\right)$. Comparing with the Chevallier-Polarski-Linder (CPL) model, the two parametrizations for dark energy can explore the whole evolution history of the universe properly. Using the current mainstream observational data including the cosmic microwave background data and the baryon acoustic oscillation data as well as the type Ia supernovae data, we perform the $\chi^2$ statistic analysis to global fit these models, finding that the logarithm parametrization and the oscillating parametrization are almost as well as the CPL scenario in fitting these data. We make a comparison for the impacts of the dynamical dark energy on the cosmological constraints on the total mass of active neutrinos. We find that the dark energy properties could significantly change the fitting results of neutrino mass. Looser constraints on $\sum m_{\nu}$ are obtained in the logarithm and oscillating models than those derived in the CPL model. Consideration of the possible mass ordering of neutrinos reveals that the most stringent constraint on $\sum m_{\nu}$ appears in the degenerate hierarchy case.

As the most active plateau on the Earth, the Qinghai-Tibet Plateau has a complex crust-mantle structure. Knowledge of the distribution of such a structure provides information for understanding the underlying geodynamic processes. We obtains a three-dimensional density model of crustal and upper mantle beneath Qinghai-Tibet plateau and its surrounding areas from the residual geoid anomalies using the Earth Gravitational Model (EGM) 2008. We estimate a refined density model by iterations, using an initial density contrast model. We confirm that the EGM2008 mission products can be used to constrain the crust-mantle density structures. Our major findings are: (1). At 300-400 km depth, high-D anomalies terminate around Jinsha River Suture (JRS) in the central TP, suggesting that the Indian plate has been reached over the Bangong Nujiang Suture (BNS) and almost reach to the JRS. (2). On the eastern TP, low-D anomalies at the depth of 0-300 km together with high-D anomalies at 400-670 km further verified the current eastward subduction of Indian plate. The ongoing subduction provides forces to the occurrences of frequent earthquakes and volcano. (3). At 600 km depth, low-D anomalies inside the TP illustrate the existence of hot weak material beneath there, contributing to the external material inward-thrusting.

This work (in two parts) will review the recently developed predictive modeling methodology called “4th-BERRU-PM” and its applicability to energy systems as exemplified by an illustrative application to the Polyethylene-Reflected Plutonium (acronym: PERP) OECD/NEA reactor physics benchmark. The acronym 4th-BERRU-PM designates the “Fourth-Order Best-Estimate Results with Reduced Uncertainties Predictive Modeling” methodology, which yields best-estimate results with reduced uncertainties for the first fourth-order moments (mean values, covariance, skewness, and kurtosis) of the optimally predicted posterior distribution of model results and calibrated model parameters. The 4th-BERRU-PM uses the Maximum Entropy (MaxEnt) principle to incorporate fourth-order experimental and computational information, including fourth (and higher) order sensitivities of computed model responses to model parameters, thus incorporating, as particular cases, the results previously predicted by the second-order predictive modeling methodology 2nd-BERRU-PM, and vastly generalizing the results produced by extant data assimilation and data adjustment procedures. The 4th-BERRU-PM methodology encompasses the scopes of high-order sensitivity analysis (SA), uncertainty quantification (UQ), data assimilation (DA) and model calibration (MC). The application of the 4th-BERRU-PM methodology to energy systems is illustrated by means of the above-mentioned OECD/NEA reactor physics benchmark, which is modeled using the neutron transport Boltzmann equation involving 21976 imprecisely known parameters, the solution of which is representative of “large-scale computations.” The model result (“response”) of interest is the leakage of neutrons through the outer surface of this spherical benchmark, which can be computed numerically and measured experimentally. Part 1 of this work illustrates the impact of high-order sensitivities, in conjunction with parameter standard deviations of various magnitudes, on the determination of the expected value and variance of the computed response in terms of the first four moments of the distribution of the uncertain model parameters. Part 2 of this work will illustrate the capabilities of the 4th-BERRU-PM methodology for combining computational and experimental information, up to and including forth-order sensitivities and distributional moments, for producing best-estimate values for the predicted responses and model parameters while reducing their accompanying uncertainties.

Soil amendments with composted organic materials are recommended to increase soil organic matter (SOM), promote soil fertility, and the Circular Economy. Growing areas of hedged olive groves in southern Iberia peninsula generate huge amounts of olive leaves whose potential as soil organic amendment is not fully studied. An experimental field trial in a hedged olive grove (cv. “Cobrançosa”) was set up near Portalegre, Portugal, to test a compost of olive leaves plus sheep manure (2:1) applied in the row, at soil surface. Three nominal rates (0 or control, 2.5 and 5.0 kg m-2) were used, in a complete randomized block setup (3 treatments, 3 replicas, 9 plots) and soil chemical properties of layers 0-5, 5-15, and 15-30 cm deep were annually monitored. Results (mainly in layer 0-5 cm) showed increases in total N, carbon of the particulate organic matter (POM-C), permanganate oxidizable carbon (POX-C), extractable phosphorus, and zinc, after one year, and increases in soil organic carbon (SOC), C-stock, pHKCl, extractable phosphorus, and zinc, after two years. POX-C was the most sensitive SOM-related indicator, showing increases up to 30 cm deep after one year. This compost improved soil fertility, but should be monitored over longer periods of time, namely for SOC and extractable zinc content.

Global warming and climate change have led to extreme changes in climatic conditions in recent years. The Taiwan government designates the construction of the Kinmen County as low carbon islands, to promote the operation of 100 electric motorcycles and battery demonstration. This study combined with island tourism, after boarding the island, visitors can rent electric motorcycles from the passenger service center and coordinate with the island tour map to show the location of the battery exchange points, so as to facilitate the search. During the operation, the amount of electric motorcycle lease is 15,551 times, the total mileage of motor vehicle is 284,404 km, the number of battery exchange is 622 times, the lease income is about NT$900,000. To reduce carbon and economic benefits of the assessment, compared to the motorcycles (50 c.c), electric motorcycles (EM 100) can reduce the carbon emissions by 8,726 kg, reducing energy costs of NT$422,594.

We find that the degeneracies and many peculiarities of the DNA genetic code may be described thanks to two closely related (fivefold symmetric) finite groups. The first group has signature $G=\mathbb{Z}_5 \rtimes H$ where $H=\mathbb{Z}_2 . S_4\cong 2O$ is isomorphic to the binary octahedral group $2O$ and $S_4$ is the symmetric group on four letters/bases. The second group has signature $G=\mathbb{Z}_5 \rtimes GL(2,3)$ and points out a threefold symmetry of base pairings. For those groups, the representations for the $22$ conjugacy classes of $G$ are in one-to-one correspondence with the multiplets encoding the proteinogenic amino acids. Additionally, most of the $22$ characters of $G$ attached to those representations are informationally complete. The biological meaning of these coincidences is discussed.

In China, environmental pollution generated via industrialization as well as the profound changes in the social structure and gradual maturation of the social hierarchy have jointly contributed to the Chinese people's increased environmental consciousness and appeals for environmental justice (EJ). Because of the absence of an EJ theory and a lack of empirical research focused on China, this paper proposes a ‘Pyramid Model’ for China’s EJ research that involves the following three factors: basic demographic and socioeconomic factors, U.S.-based EJ principles, and Chinese characteristics. A nationwide pilot analysis of environmental inequity at the prefecture level is conducted by empirically studying the association of demographics and socioeconomic status with sources of industrial pollution in China. The prefecture-based results are shown to be robust and indicate that areas inhabited by ethnic minorities and western regions in China carry disproportionate environmental burdens. However, a different picture for migrants is presented, revealing that Chinese migrants are not currently exposed to greater levels of industrial pollution, and relevant interpretations of these findings are provided. The results also show that environmental inequality associated with income level, which is observed in the U.S., does not occur in China.

Cotton fiber, a crucial and sustainable resource for global textile production, undergoes a complex five-stage developmental process, encompassing initiation, elongation, transition, secondary cell wall biosynthesis, and maturation. These elongated single-cell fibers originate from the outer ovule epidermis. The development of cotton fibers involves intricate changes in gene expression and physiological processes, resulting in a nearly pure cellulose product vital for the global cotton industry. Decoding genes associated with fiber development enhances our understanding of cotton fiber mechanisms and facilitates the cultivation of varieties with enhanced quality. In recent decades, advanced omics approaches, including genomics, transcriptomics, and proteomics, have played a pivotal role in identifying genes and gene products linked to cotton fiber development, including the MYB transcription factor family which coordinates cotton fiber development. Molecular studies have revealed transcription factors like MYB, WRKY, Homeodomain Leucine Zipper (HD-ZIP) and basic Helix-Loop-Helix (bHLH) influencing fiber initiation and elongation. The intricate interplay of phytohormones like auxin, gibberellic acid (GA), brassinosteroid (BR), jasmonic acid (JA), ethylene, abscisic acid (ABA), and cytokinin is explored, providing a comprehensive perspective on shaping cotton fibers. Numerous candidate genes and cellular processes affecting various aspects of fiber development hold promise for genetic engineering or marker-assisted breeding to improve fiber quality. This review presents a comprehensive overview of key achievements in cotton molecular biology, with a specific emphasis on recent advancements in understanding transcription factors and phytohormones involved in cotton fiber initiation and elongation.

In recent years, video anomaly detection technology , which can intelligently analyze massive video and quickly find abnormal phenomena, has attracted extensive attention with the wide application of video surveillance technology . To address the complex and diverse problem of abnormal human behavior detection in surveillance videos, a surveillance video abnormal behavior detection and localization supervised method based on the deep network model and the traditional method is proposed. Specifically, we combined AGMM and YOLACT methods to obtain more accurate foreground information by fusing the foreground maps extracted by each technique. To further improve the accuracy , we use the PWC-Net technique to extract features of the foreground images and input them into an anomaly classification model for classification. The proposed method effectively detects and locates the abnormal behavior in the monitoring scene. In addition to the aforementioned methods, this paper also employs YOLOV5 and DeepSORT networks for object detection and tracking in the video, which allows us to track the detected objects for better understanding of the scene in the video. Experiments on the UCSD benchmark dataset and the comparison with state-of-the-art schemes prove the advantages of our method.

By using the particle swarm optimization algorithm for crystal structure prediction, we reveal a newly orthorhombic Cmcm structure of HfB4, which is more energetically superior to the previously proposed YB4-, ReP4-, FeB4-, CrB4-, and MnB4-type structures in the considered pressure range. The phonon dispersion and elastic constants calculations confirm that the new phase is dynamically and mechanically stable. The calculated large shear modulus (240 GPa) and high hardness (45.7 GPa) imply that the predicted Cmcm-HfB4 is a potential superhard material. Meanwhile, the directional dependences of the Young's modulus, bulk modulus, and shear modulus for HfB4 are systematically investigated. Further analyses of the density of states and electronic localization function indicate that the strong B-B and B-Hf covalent bonds greatly contribute to its high hardness and stability.

In recent years, researchers have paid increasing attention on hyperspectral image (HSI) classification using deep learning methods. To improve the accuracy and reduce the training samples, we propose a double-branch dual-attention mechanism network (DBDA) for HSI classification in this paper. Two branches are designed in DBDA to capture plenty of spectral and spatial features contained in HSI. Furthermore, a channel attention block and a spatial attention block are applied to these two branches respectively, which enables DBDA to refine and optimize the extracted feature maps. A series of experiments on four hyperspectral datasets show that the proposed framework has superior performance to the state-of-the-art algorithm, especially when the training samples are signally lacking.

Elevated circulating triglyceride levels have been linked to an increased risk of diabetes, although the precise mechanisms remain unclear. This study aimed to investigate whether low-density lipoprotein (LDL) cholesterol, homeostatic model assessment (HOMA) for insulin resistance, and C-reactive protein served as mediators in this association across a sample of 18,435 US adults. Mediation analysis was conducted using the PROCESS Version 4.3 Macro for SPSS. Simple medi-ation analysis revealed that all three potential mediators played a role in mediating the associa-tion. However, in the parallel mediation analysis, where all three mediators were simultaneously included, HOMA for insulin resistance remained a significant mediator (indirect effect coefficient, 0.47; 95% confidence interval [CI], 0.43—0.52; p < 0.05) after adjusting for all tested confounding factors. Conversely, LDL cholesterol (indirect effect coefficient, -0.13; 95% CI, -0.31—0.05; p > 0.05) and C-reactive protein (indirect effect coefficient, 0.01; 95% CI, -0.003—0.02; p > 0.05) ceased to be significant mediators. HOMA for insulin resistance accounted for 49% of the association between triglycerides and diabetes. In conclusion, HOMA for insulin resistance was the dominant mediator underlying the association between triglycerides and diabetes. Therefore, reducing triglyceride levels may hold promise for improving insulin sensitivity in diabetic patients.

This study investigated the adaptability of Dunaliella salina to different salinity levels, with emphasis on growth, pigment concentration, and desalination potential. It was found that among the 21 salinity levels, salinity 75 produced consistently favorable results in cell count (13.08 x 10³ ± 1.41 x 10³ cells/mL), dry biomass (2.46 ± 0.06 g/L), pigment content (chlorophyll a = 97.5 ± 0.1 µg/L, chlorophyll b = 123.6 ± 0.3 µg/L), and desalination (9.32 ± 0.47 reduction). Therefore, salinity 75 was selected for the final trial (scale-up), which revealed unanticipatedly high cell counts (58.96 x 10³ ± 535.22 cells/mL), with dry biomass weight being statistically different (higher) than the expected (4.21 ± 0.02 g/L) (p<0.0001), most likely due to high cell count and energy reserve storage for high salinity adaption in the form of bio-compounds. Pigment growth continued (chlorophyll a = 95.4 ± 2.2 µg/L, chlorophyll b = 128.1 ± 5.1 µg/L), indicating pigment production under salt stress. Notably, desalination did not occur in this stage, possibly due to the necessity for a bigger initial inoculate, prolonged exposure or bioaccumulation becoming the prevailing mechanism over desalination. Nevertheless, the trial highlights D. salina's strong adaptation to various salinity levels. This suggests a promising future in halophyte research, particularly in understanding the mechanisms that prevent salt accumulation in cells and how to overcome this barrier. Additionally, these results suggest that microalgae could be a viable resource in saline-rich environments unsuitable for conventional agriculture, promoting industrial adaptation to adverse conditions.

Purpose: The treatment of renal fibrosis caused by long-term obstructive nephropathy is limited. The purpose of this study was to establish a mouse model of renal fibrosis with unilateral ureteral obstruction (UUO) and to treat it with exosomes derived from SIRT6 transfected urine-derived stem cells (USCs), which will determine whether exosomes have the effect of anti-fibrosis Methods: The renal fibrosis model of UUO mice was established by ligating unilateral ureter. USCs were extracted from human urine and transfected with SIRT6 lentivirus plasmid. The SIRT6-USCs-exosomes(SIRT6-USCs-exos) were collected and identified by transmission electron microscope, nanoparticle tracking analysis and western blot. SIRT6-USCs-exos were injected into the tail vein of mice and the renal tissue of mice was stained with HE. The relative gene expressions of α-SMA, E-cadherin and TGF-β1 were analyzed by RT-qPCR. Results: In this study, we successfully constructed the renal fibrosis model of UUO mice and hUSCs with overexpression of SIRT6. The SIRT6-USCs-exos significantly improved the renal fibrosis in UUO mice. The relative mRNA expressions of fibrosis-related genes α-SMA, E-cadherin and TGF-β1 in renal tissue were significantly down-regulated after SIRT6-USCs-exos treatment. Conclusion: Our results indicate that SIRT6-USCs-exos can effectively alleviate renal fibrosis caused by long-term obstructive nephropathy. The findings may be promising for dealing with renal fibrosis.

Management of chronic inflammation and wounds has always been a key issue in the pharmaceutical and healthcare sector. Curcumin (CCM) is an active ingredient extracted from turmeric rhizomes that has antioxidant, anti-inflammatory, and antibacterial activities, thus showing significant effectiveness toward wound healing. However, its shortcomings such as poor water solubility, poor chemical stability and fast metabolic rate limit its bioavailability and long-term use. In this context, hydrogels appear to be a versatile matrix for carrying and stabilizing drugs due to the biomimetic structure, soft porous microarchitecture, and pleasant biomechanical properties. The drug loading/releasing efficiencies can also be controlled by use of highly crystalline and porous metal organic frameworks (MOFs). Here, a flexible hydrogel composed of sodium alginate (SA) matrix and CCM-loaded MOFs was constructed for long-term drug release and antibacterial activity. The morphology and physicochemical properties of composite hydrogels were analyzed by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), ultraviolet visible spectroscopy (UV-Vis), Raman spectroscopy and mechanical property tests. The results showed that the composite hydrogel was highly twistable and bendable to mechanically comply with human skin. The as-prepared hydrogel could capture efficient CCM for slow drug release as well as effective killing of bacteria. Therefore, such composite hydrogel is expected to provide a new management system for chronic wound dressings.

This study aims to test a model linking destination image, perceived value, tourist satisfaction, and tourist loyalty. Based on a sample of 300 tourists travelling by car from the World Natural Heritage Site of Tianchi, China, a new model of destination image was explored and data were analysed using partial least squares structural equation modelling (PLS-SEM). The results show that perceived value and satisfaction are direct antecedents of destination loyalty. Above all, perceived value and tourist satisfaction mediate the relationship between destination image and loyalty. Finally, this study discusses the theoretical and management implications of the findings in order to boost the tourism industry in the context of car trips.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

With the increasing concern of environment, the energy-efficiency scheduling of manufacturing industry is becoming urgent and popular. In turning processes, both spindle speed and processing time can affect the final energy consumption and thus the spindle speed and scheduling scheme need to be optimized simultaneously. Since the turning workshop can be regarded as the flexible flow shop, this paper formulates a mixed integer linear programming model for energy-efficient scheduling of flexible flow shop. Accordingly, a new decoding method is developed by considering of the optimization of spindle speed and scheduling scheme simultaneously, and an estimation of distribution algorithm adopting the new decoding method is proposed to solve large-size problems. The parameters of this algorithm are determined by statistical technique with a simplified practical case. In order to validate the proposed method, a case from practical factories is studied, in which the makespan can be shortened by 25.22%, and the consumed energy can be saved by 5.48%. These results demonstrate the effectiveness of the proposed mathematical model and algorithm.

Ransomware attacks have rapidly proliferated, inflicting severe financial damages on businesses and individuals. Machine learning approaches to automate ransomware detection have shown promise but grapple with challenges like limited training data. This study introduces a novel deep learning model for few-shot ransomware classification. The model employs entropy features derived directly from malware binaries coupled with a twin neural network architecture utilizing transfer learning. Tests on over 1000 samples across 11 families demonstrate a weighted F1-score of 85.8\%, surpassing existing methods. The approach mitigates biases in limited training data and preserves intricacies lost in image-based features. It exhibits precise classification capabilities even with sparse samples of new ransomware variants. The research highlights the potential of entropy-driven deep learning to equip defenses against emerging zero-day ransomware strains.

Ransomware attacks have risen alarmingly, with encryption techniques becoming more complex. This paper introduces a novel detection model tailored for ransomware's distinctive characteristics. The Intel PIN tool extracts Windows API invocation sequences related to file operations. These sequences are used to construct n-grams, forming feature vectors enhanced by a new Class Feature Weighting (CFW) metric to improve malware detection. Preliminary results demonstrate elevated accuracy and precision versus existing methods. The major contributions are: (1) Introducing an innovative deep learning model for few-shot ransomware classification using entropy features and transfer learning. (2) Achieving high weighted F1-score in classifying ransomware variants into families with limited training data. (3) Demonstrating the potential of entropy-based features to capture intricacies lost in image-based approaches, improving detection of new strains.

This paper explores the application of Large Language Models (LLMs), such as GPT-3 and GPT-4, in generating cybersecurity policies and strategies to mitigate ransomware threats, including data theft ransomware. We discuss the strengths and limitations of LLMs for ransomware defense and provide recommendations for effectively leveraging LLMs while ensuring ethical compliance. The key contributions include a quantitative evaluation of LLM-generated policies, an examination of the legal and ethical implications, and an analysis of how LLMs can enhance ransomware resilience when applied judiciously.

Consciousness pervades our daily experiences, yet it remains largely unaccounted for in contemporary physics and chemistry theories. Several existing theories, such as the Integrated Information Theory (IIT), Global Workspace Theory (GWT), Electromagnetic Field Theory (EMF Theory of Consciousness), and Orchestrated Objective Reduction Theory (Orch-OR), attempt to clarify the essence of consciousness. Yet, they often encounter significant challenges. These challenges arise due to the intricate nature of our neural systems and the limitations of current measurement and computational technologies, which often prevent these theories from being rigorously mathematically described or quantitatively tested. Here we introduce a novel theory that hypothesizes consciousness as an inherent property of certain particle configurations. Specifically, when a group of particles align in a particular state, they exhibit consciousness. This relationship between particle states and conscious perceptions is governed by what we term the "universal consciousness code". And we propose a possible practical mathematical method to decipher the complex relationship between neural activities and consciousness and to test our theory using the latest artificial intelligence technologies.

The essence of cross-modal generation and retrieval modeling for image-text interactions lies in semantic consistency. Among these, cross-modal representation alignment serves as the foundational requirement for achieving cross-modal semantic consistency. The crux of our proposed method entails the collaborative training of an image captioning model(referred to as the ’captioner’) and a pair of contrastive encoders for image-text matching(referred to as the ’concoder’). This synergistic approach yields concurrent enhancements in concoder’s performance, captioner’s proficiency, and cross-modal semantic coherence. We coin the proposed method as ‘ReCap’. To begin, we initialize the concoder through knowledge distillation from a pre-trained model. During the training process, we use the output of the initialized concoder as input to a residual attention network, jointly training it with the captioner to achieve semantic consistency. Subsequently, we iteratively update the concoder during the image-text momentum encoding phase using the residual attention network, creating a closed-loop for semantic consistency resolution. Upon completion of training, the concoder and captioner modules can be used independently to perform tasks related to cross-modal retrieval and cross-modal generation of text and images. In order to substantiate the efficacy of our proposed method, we initially conducted empirical experiments encompassing image-text retrieval and image captioning tasks, employing a widely recognized benchmark dataset, MSCOCO. Subsequently, we assessed the fine-grained cross-modal alignment performance of the concoder through an image classification task on the iNaturalist 2018 dataset. The achieved performance metrics notably surpassed those achieved by several incumbent state-of-the-art models, thus validating the proficiency of our method. Finally, motivated by the practical requirements of handling the nature conservation image data, we performed caption annotation for the iNaturalist 2018 dataset. Subsequently, we trained the ReCap on this annotated data. Experimental results demonstrate that our proposed method can maintain semantic consistency between cross-modal retrieval and image caption generation for species with similar visual features but distinct semantics. This achievement signifies a meaningful exploration in the field of cross-modal semantic consistency representation, holding significant practical value in the domain of biological research.

In this paper, the preparation methods of porous silicon nitride materials with controllable dielectric constant and pore structure were systematically studied. By using microwave sintering technology, porous silicon nitride materials with high closed pore ratio were prepared by adjusting the content of sintering additives and sintering process parameters, and controlling the grain boundary phase and pore structure and size. The effects of sintering conditions on the total porosity, closed porosity, pore structure and dielectric properties of materials were systematically studied.

Under the development mode of deep blending of emerging technologies, major projects are important for enhancing China's comprehensive national strength and independent innovation capability. Based on the social benefits of major projects, and considering the influence of reputation factors, an evolutionary game model composed of a general contractor and subcontractor of major projects is established. This paper studies the influence of various factors including the income distribution coefficient of collaborative innovation, and MATLAB simulation software is analyzed the influence of factors on an evolutionary path. The results show that a reasonable income distribution coefficient can promote the game behavior of both parties to the direction of active collaborative innovation; The reduction of innovation cost and the improvement of spillover technology absorption capacity can make innovation subjects tend to choose active collaborative innovation strategies. In addition, reputation loss above a specific threshold can effectively inhibit free-riding behavior and encourage innovation subjects to choose active collaborative innovation strategies. The research results provide reference for promoting major projects' technology innovation.

Myocardial infarction (MI) is a serious cardiovascular disease that can lead to death. Cardiac troponin I (cTnI) is a biomarker of MI in the circulation system. For detection cTnI protein, many method suffer the same problem, time-consuming. Main drawbacks are time consuming, have tedious operation, require an expensive reader for translating signals, and require non-accessible reagents. Our goal is to create a kit for cTnI protein testing, that the result can easily be read by color difference. The main breakthrough is, the resolution between different concentration can be told by eyes. The result will be future used to create a commercial, potable, convenient, daily-used rapid-test kit. In this study, a cTnI biosensor is proposed that can be read by the naked eye, performs diagnosis based on the pattern color, does not require a reader machine, is easy to operate, and is portable. Our work proposed a device that shortens the diagnosis time, has a quantitative analysis range of 0.32 –200 ng/mL in the human serum matrix, has a 0.32 ng/mL limit of detection (LOD), and shows many advantages comparing to traditional cTnI ELISA plate.

In Taiwan, farmers often apply excess compost to ensure adequate crop yield in highly frequent tillage, highly weathered, and lower fertility soils. The potential of biochar (BC) for diminishing soil C mineralization, and improving soil nutrient availability in compost over-fertilized soil is promising, but the study is still under-examined. To test the hypothesis, 434 days in vitro C mineralization kinetics of incubation experiment were conducted. Woody BC 0%, 0.5%, 1.0% and 2.0% (w/w) made of lead tree (Leucaena leucocephala (Lam.) de. Wit) were added to an Oxisols, and two Inceptisols of Taiwan. In each treatment, 5% swine manure compost (2 times recommended amount) was added and served as the over-fertilized soil. The results indicated that soil type strongly influenced the impact of BC addition on soil carbon mineralization potential. Respiration per unit of total organic carbon (total mineralization coefficient, TMC) of three studied soils significantly decreased with BC addition increased. Principal component analysis (PCA) suggested that for retaining more plant nutrients in addition to the effects of carbon sequestration, it is recommended that farmer could use locally produced biochars and composts in highly weathered and highly frequent tillage soil. Adding 0.5%-1% woody BC in soil should be reasonable and appropriate.

In Taiwan, farmers often apply excess compost to ensure adequate crop yield in highly frequent tillage, highly weathered, and lower fertility soils. The potential of biochar (BC) for diminishing soil C mineralization, and improving soil nutrient availability in compost over-fertilized soil is promising, but the study is still under-examined. To test the hypothesis, 434 days in vitro C mineralization kinetics of incubation experiment were conducted. Woody BC 0%, 0.5%, 1.0% and 2.0% (w/w) made of lead tree (Leucaena leucocephala (Lam.) de. Wit) were added to an Oxisols, and two Inceptisols of Taiwan. In each treatment, 5% swine manure compost (2 times recommended amount) was added and served as the over-fertilized soil. The results indicated that soil type strongly influenced the impact of BC addition on soil carbon mineralization potential. Respiration per unit of total organic carbon (total mineralization coefficient, TMC) of three studied soils significantly decreased with BC addition increased. Principal component analysis (PCA) suggested that for retaining more plant nutrients in addition to the effects of carbon sequestration, it is recommended that farmer could use locally produced biochars and composts in highly weathered and highly frequent tillage soil. Adding 0.5%-1% woody BC in soil should be reasonable and appropriate.

This research used an experimental study design in which 60 subjects were randomly assigned to either an experimental (image e-book guidance) group or a control (text guidance) group after meeting the admission conditions and agreeing to participate in the study. It was proven that providing image e-book guidance before surgery significantly changed the behavior of patients and promoted relief of urinary catheter discomfort through self-efficacy to reduce urinary catheter pain after surgery. It was found that providing image e-book guidance can shorten the time for health education and provide patients with repeated medical education and familiarity with health guidance, which can help to address the important clinical service demand issue and the shortage of nursing staff.

Unpaid family caregivers might suffer losses in income as a result of care provision. Here we used data from the baseline survey of the China Health and Retirement Longitudinal Study to assess the relationship between hours of weekly caregiving provided to grandchildren/parents/parents-in-law and individual’s monthly employment income. Our study sample comprised 3,718 middle-aged Chinese adults who were of working age (45-60 years). For women and men separately, we used a likelihood-based method to determine a caregiving threshold in a two-stage Heckman selection procedure. Instrumental variables were used to rule out the endogeneity of caregiving hours. Our analysis revealed a negative association between caregiving and income for women that depended on a caregiving threshold of 63-hours per week. There was an absence of caregiving-income relationship among men. These results offer new insights into the opportunity costs of unpaid caregiving and support tailored policies to protect the financial well-being of female caregivers.

Robotic systems have been widely used in various industries, so the security of communication between robots and their components has become an issue that needs to be focused on. As a framework for developing robotic systems, the security of ROS2 can directly affect the security of the upper-level robotic systems. Therefore, it is a worthwhile research topic to detect and analyze the security of ROS2. In this paper, we adopt a formal approach to analyze the security of the communication mechanism of ROS2. First, we use a state transition system to model the potential vulnerabilities of ROS2 based on the ROS2 communication mechanism and the basic process of penetration testing. Secondly, we introduce the CIA model on the basis of the established vulnerability model and use LTL to define its security properties. Then, we design and implement a vulnerability detection tool for ROS2 applications based on the vulnerability model and security properties. Finally, we experimentally test some ROS2-based applications, and the results show that ROS2 has vulnerabilities without additional protection safeguards.

Efficiency serves as a crucial metric in assessing the advancement of scientific research for universities. Reasonable inputs of human resources, finances, materials, and other resources, along with high-quality research output, are important guarantees for the research efficiency of Chinese universities. This study delves into the patterns of changes of research efficiency among universities across the 31 provinces and municipalities of China from 2012 to 2022. By scrutinizing input-output perspectives and utilizing data sourced from the China Statistical Yearbook, the analysis unveils prevailing scenarios of input redundancy and output insufficiency in research efficiency across universities. The static and dynamic trends in research efficiency were further investigated by employing a static non-parametric Data Envelopment Analysis (DEA)-BCC model and a dynamic Malmquist index. Key findings from the analysis from 2012 to 2022 include: (1) notable growth in investments in teaching, research equipment assets, and research and development funds among nationwide universities; (2) a steady increase in the mean value of technical efficiency (TE) from 0.97 to 0.99, indicating continuous enhancement in overall efficiency in research input resource allocation across the provinces; (3) the mean Malmquist productivity index of 1.285, with an average annual increase of 28.5%, signifying a consistent improvement in university research efficiency throughout the study period; and (4) the provinces experiencing varying degrees of input redundancy or output insufficiency were selected to suggest the need for tailored strategies in resource allocation. The study underscores the importance of a holistic evaluation system involving stakeholders from government, universities, and society to optimize research efficiency and promote scientific innovation and social development.

Previous research has paid little attention to the relationship between corporate governance and brand equity in the tourism industry. This study aims to investigate the moderating effect of corporate governance (CG) on the relationship between brand equity (BE) and corporate profit-ability (CP) with ten control variables including five company characteristics and five macroeconomic variables. Financial data is retrieved from the Taiwan Economics Journal Database (TEJ), covering a total of 196 records from 32 listed companies for 16 years. Results indicate that BE has a significantly positive impact on CP in Taiwanese-listed tourism companies, and that CG moderates the relationship between BE and CP. These findings could help management executives enhance profitability by deepening BE and CG in the tourism industry. Managerial implications are also discussed.

Timely and accurate information on tree species is crucial for the sustainable management of natural resources, forest inventory, biodiversity detection, and carbon stock calculation. The advancement of remote sensing technology and artificial intelligence has facilitated the acquisition and analysis of remote sensing data, resulting in more precise and effective classification of tree species. Multimodal remote sensing data and deep learning seem to be the current tree species classification research mainstream, whether or not. The current review on the remote sensing data and deep learning tree species classification methods perspectives to analyze the unimodal and multimodal remote sensing data and classification methods in this realm is missing. To bridge the gap, we search for major trends in the remote sensing data and tree species classification methods, provide a detailed overview of classic deep learning-based methods for tree species classification, and discuss the limitations.

Keywords: mHealth; peritoneal dialysis; functionality; usability

China is experiencing rapid urbanization. The focus on health issues has shifted from the treatment of diseases to passive or active prevention. Diseases caused by the deterioration of the urban environment, such as cardiovascular disease, diabetes, obesity and other chronic diseases and mental illness, have gradually become the main threat to public health. Studies have confirmed that urban green spaces (UGS) can help residents relieve mental stress, improve mood, reduce mental fatigue and restore attention, which has a positive effect on people's physical and mental health. In this study, the relationship between the quantity and quality factors of UGS and the physical and mental health of urban residents in Xihu District of Hangzhou is examined, and on this basis, UGS design strategies are proposed to promote the physical and mental health of residents. This study is of great significance for the future construction of UGS that are beneficial to the health of residents and the promotion of a healthy China and healthy city construction.

At present, medical institutes generally use EMR to record patient's condition, including diagnostic information, procedures performed and treatment results. EMR has been recognized as a valuable resource for large scale analysis. However, EMR has the characteristics of diversity, incompleteness, redundancy and privacy, which make it difficult to carry out data mining and analysis directly. Therefore, it is necessary to preprocess the source data in order to improve data quality and improve the data mining results. Different types of data require different processing technologies. Most structured data commonly needs classic preprocessing technologies, including data cleansing, data integration, data transformation and data reduction. For semi-structured or unstructured data, such as medical text, containing more health information, it requires more complex and challenging processing methods. The task of information extraction for medical texts mainly includes NER (Named Entity Recognition) and RE (Relation Extraction). In this paper, we introduce the process of EMR processing, including data collection, data preprocessing, data mining, evaluation and knowledge application, analyze the current status of the key technologies, such as data preprocessing and data mining, and provide an overview of the application domains and prospects of EMR mining technologies. Finally, we summarize the existing problems in the research of EMR mining, and review the development trends.

A (2,6)-fullerene F is a 2-connected cubic planar graph whose faces are only 2-length and 6-length. Furthermore, it consists of exactly three 2-length faces by Euler's formula. The (2,6)-fullerene comes from Do\v{s}li\'{c}'s (k,6)-fullerene, a 2-connected 3-regular plane graph with only k-length faces and hexagons. Do\v{s}li\'{c} showed that the (k,6)-fullerenes only exist for k = 2, 3, 4 or 5, and some of the structural properties of (k,6)-fullerene for k = 3, 4 or 5 are studied. In this paper, we study the properties of (2,6)-fullerene. We obtain that the edge-connectivity of (2,6)-fullerenes is 2. Every (2,6)-fullerene is 1-extendable, but not 2-extendable. F is said to be k- resonant (k>0) if the deleting of any i (0=< i<= k) disjoint even faces of F results in a graph with at least one perfect matching. We have that every (2,6)-fullerene is 1-resonant. An edge set S of F is called an anti-Kekule set if F-S is connected and has no perfect matchings, where F-S denotes the subgraph obtained by deleting all edges in S from F. The anti-Kekule number of F, denoted by ak(F), is the cardinality of a smallest anti-Kekule set of F. We have that every (2,6)-fullerene F with |V(F)|>6 has anti-Kekule number 4. Further we mainly prove that there exists a (2,6)-fullerene F having f_{F} hexagonal faces, where f_{F} is related to the two parameters n, m.

Unpaid family caregivers must consider the economic trade-off between caregiving and paid employment. Prior literature has suggested labour force participation (LFP) to decline with caregiving intensity, but no study has evaluated this relationship by accounting for the presence of both kinks and discontinuities. Here we used respondents of the China Health and Retirement Longitudinal Study baseline survey who were non-farming, of working-age (aged 45-60) and had a young grandchild and/or a parent/parent-in-law. For women and men separately, a caregiving threshold-adjusted probit model was used to assess the association between LFP and weekly unpaid caregiving hours. Instrumental variables were used to rule out the endogeneity of caregiving hours. Of the 3,718 respondents in the analysis, for men, LFP was significantly and inversely associated with caregiving that involved neither discontinuities nor kinks. For women, a kink was identified at the caregiving threshold of 8 hours per week such that before 8 hours, each caregiving hour was associated with an increase of 0.0257 in the marginal probability of LFP, but each hour thereafter was associated with a reduction of 0.0014 in the marginal probability of LFP. These results have implications for interventions that simultaneously advance policies of health, social care and labour force.

Inside hippocampal circuits, neuroplasticity events that individual cells may undergo during synaptic transmissions occur in the form of Long Term Potentiation (LTP) and Long Term Depression (LTD). The high density of NMDA receptors expressed on the surface of the dendritic CA1 spines confers to hippocampal CA3-CA1 synapses, the ability to easily undergo NMDA-mediated LTP and LTD, that is essential for some forms of explicit learning in mammals. Providing a comprehensive kinetic model that can be used for running computer simulations of the synaptic transmission process is currently a major challenge. Here, we propose a compartmentalized kinetic model for CA3-CA1 synaptic transmission. Our major goal was to tune our model in order to predict the functional impact caused by disease associated variants of NMDA receptors related to severe cognitive impairment. Indeed, for variants Glu413Gly and Cys461Phe, our model predicts negative shifts in the glutamate affinity and changes in the kinetic behavior, consistent with experimental data. These results pinpoint to the predictive power of this multiscale viewpoint, which aims to integrate the quantitative kinetic description of large interaction networks typical of system biology approaches with a focus on the quality of few, key, molecular interactions typical of structural biology ones.

In recent years, the Chinese government pays more and more attention to agricultural development and ecological protection. While improving the cultivated land green use efficiency(CLGUE) is the key to promote the sustainable development of agriculture. This study aims to study the current situation and influencing factors of agricultural production from the perspective of green utilization efficiency of cultivated land. It takes 39 cities in the upper, middle and lower reaches of the Yangtze River basin in China as an example. The CLGUE values in those 39 cities from 2011 to 2020 were specifically measured, using the Super-SBM model, kernel density estimation and geographic detector method. Their temporal and spatial heterogeneity was described, and the influencing factors were detected at both single and interactive levels. The results showed that: （1）From 2011 to 2020, the green utilization efficiency value of cultivated land in the Yangtze River Basin showed an upward trend on the whole; （2）There is a clear spatial heterogeneity the CLGUE values in the Yangtze River Basin cities, as shown by: downstream region > midstream region > upstream region; (3) Cultivated land resource endowment, socioeconomic development, and agricultural production technology are important factors affecting the variability of CLGUE values. However, there are some differences in the degree and direction of influence of different influencing factors on different sample subgroups.

Network Embedding (NE) is an important method to learn the representations of network via a low-dimensional space. Conventional NE models focus on capturing the structure information and semantic information of vertices while neglecting such information for edges. In this work, we propose a novel NE model named BimoNet to capture both the structure and semantic information of edges. BimoNet is composed of two parts, i.e., the bi-mode embedding part and the deep neural network part. For bi-mode embedding part, the first mode named add-mode is used to express the entity-shared features of edges and the second mode named subtract-mode is employed to represent the entity-specific features of edges. These features actually reflect the semantic information. For deep neural network part, we firstly regard the edges in a network as nodes, and the vertices as links, which will not change the overall structure of the whole network. Then we take the nodes' adjacent matrix as the input of the deep neural network as it can obtain similar representations for nodes with similar structure. Afterwards, by jointly optimizing the objective function of these two parts, BimoNet could preserve both the semantic and structure information of edges. In experiments, we evaluate BimoNet on three real-world datasets and task of relation extraction, and BimoNet is demonstrated to outperform state-of-the-art baseline models consistently and significantly.

In this study, we discuss the thermospheric density response to the solar activity and QBO. By using the wavelet power spectrum method, the thermospheric density from 1967 to 2013 shows ~11-year period, semiannual and annual variations, while the seasonal variation is usually more significant under high solar activity conditions. Importantly, we investigate the possible link between the density and the QBO, with the aid of GAMDM model and different density residual method. As a result, the difference between the measured density and empirical model seemingly has QBO signal, but the ratio of them revels that the QBO signal does not exist in the thermospheric density. Comprehensively, we thought the stratospheric QBO cannot impact on the thermosphere, and more data and numerical modeling are needed for further validation.

This research provides a computationally efficient numerical tool for predicting 3-D turbulent flows over hydrofoils. It addresses a gap in existing numerical methods by extending the capabilities of the laminar VIScous Vorticity Equation (VISVE) solver to handle 3-D turbulent flow scenarios. The implementation integrates the k − ω SST model into the 3-D VISVE solver using the Finite Volume Method (FVM), extending its capability to handle turbulent flows. The turbulence model is also parallelized to improve computational efficiency. The application of the newly developed model to 3-D hydrofoil cases expands its scope and serves as preparatory work for future rotational propeller applications. Rigorous testing includes a convergence analysis concerning grid numbers and time step sizes, and validation against a Reynolds-Averaged Navier-Stokes (RANS) solver ensures the reliability and accuracy of the enhanced VISVE solver for turbulent flow simulations. The turbulent VISVE solver offers advantages such as reduced computational domain and costs through a vorticity-based approach. Turbulence concentration within boundary layers and free shear flows does not compromise the advantages of the small computational domain. The simplified meshing process, automatically generated by denoting the number of panels on the hydrofoil, makes the solver accessible for researchers and engineers.

The ZX Spectrum was a popular 8-bit home computer by Sinclair Research in the 80s. Even though some of these computers may still work, the audio tapes, the TV with an analog tuner and the micro-switch joystick, used with the original ZX Spectrum, nowadays are outdated and hard to find in good working order or replicate. Since many other old closed systems are also very difficult to update to support modern peripherals, there is a necessity to provide a methodology to adapt such systems to support new peripherals while being compatible with existing software. The work proposed in this paper is focused on recreating a ZX Spectrum+/48k computer and interface it with modern peripherals on an FPGA. This is accomplished by adding a co-processor to assist with the control of the new peripherals which would either require to complex architectural changes to the original system and in the end it would perform poorly due to the low performance of the Z80 CPU. This work distances from previous ones on emulating a ZX Spectrum since it focuses on the use of different upgraded peripherals and the use of a NIOS II soft-processor as a co-processor to manage the SD Card accesses. A demonstration of the proposed modernized architecture was made by successfully running a diagnostics ROM and playing original ZX Spectrum games from an SD card for game with a PS/2 keyboard and a pair of joysticks.

This article explores the relationship between green energy and cryptocurrencies in the sustainable energy finance sector. The research findings contribute to our understanding of the application of green economy practice, enabling investors in financial markets, policymakers, and stakeholders to make informed decisions and develop specific strategies. Adopting the green economy paradigm makes it possible to promote collaboration and innovation by integrating ethical and responsible principles that can improve the overall quality of processes and boost sustainable growth. Cryptocurrencies have been widely used as financial instruments over the last decade. Given the development of the cryptocurrency market and the growing awareness of greener and more energy-efficient tokens, the green economy has become a popular topic for understanding economic and political issues. However, the literature still lacks clear evidence on how cryptocurrencies interact with green energies. Therefore, this study examines the long- and short-term relationships between dirty cryptocurrencies such as Bitcoin (BTC), Ethereum (ETH), clean cryptocurrencies such as Cardano (ADA), Ripple (XRP), Stellar (XLM), and green energies such as ISE Clean Edge Global Wind Energy, S&amp;P Global Clean Energy, S&amp;P TSX Renewable Energy and Clean Technology, Solactive China Clean Energy, in the period from January 2020 to September 2023. The results show that diversification is key, with clean cryptocurrencies such as ADA, XLM and XRP offering diversification opportunities alongside "dirty" cryptocurrencies such as BTC and ETH. Although sustainable energy indices show mixed evidence in the long and short term, they remain relevant for those who focus on clean energy investments. It is also becoming increasingly relevant for investors in sustainable portfolios to assess their environmental impact, especially for energy-intensive cryptocurrencies, and it is advisable to explore sustainable blockchain technologies.

As a stimulus signal, coded electrical signals can control the motion behavior of animals, which has been widely used in the field of animal robots. In current research, most of the stimulus signals used by researchers are traditional waveform, such as square waves. To enrich the stimulus waveform, a wireless animal robot stimulation system based on neuronal electrical signal characteristics is presented in this paper. The stimulator uses the CC1101 wireless module to control animal behavior through brain stimulation. The LabVIEW-based graphical user interface(GUI) can manipulate brain stimulation remotely while the stimulator powered by battery. Additionally, the spikes of animals have been simulated by this system through Direct Digital Synthesizer(DDS) algorithm. The GUI enable users to customize the combination of these analog spike signals. The recombined signals are sent to the stimulator through CC1101 as stimulus signals. In vivo experiments conducted on five pigeons verified the efficacy of the stimulation mechanism. The analog spike signal with an amplitude of 3-5V successfully caused the pigeon’s turning behavior. The feasibility of the analog spike signals as stimulus signals was successfully verified. Increased the diversity of stimulus waveform in the field of animal robots.

The utilization of primary school buildings is multifaceted, primarily due to the high occupancy density, varying thermal preferences among occupants, diverse indoor activities (such as walking, sports, and conversation), and a constant flow of individuals entering and exiting the building. This results in frequent opening and closing of external windows and doors and fluctuations in internal heat gain. Consequently, frequent interactions between the indoor and outdoor microenvironments lead to energy losses. This study conducts a comprehensive literature review on building energy loss stemming from occupant behavior and the interactions between indoor and outdoor microenvironments. Furthermore, it proposes a dynamic real-time monitoring system based on a computer data capture and visualization platform foundation for building energy loss. The research methods include data crawling, data association rule mining, and data association analysis. The research findings yield a universally applicable and informative building energy-saving design theory based on extensive data analysis. Additionally, the system presents information on occupants' behavior and the microclimate data of indoor and outdoor environments on a computer screen, facilitating human-machine communication and enabling timely adjustments to design strategies for new buildings and operation and maintenance strategies for existing buildings.

This study explores the implementation of an interdisciplinary curriculum in product and media design education and its impact on knowledge innovation and competency development. The curriculum is based on scaffolding theory, incorporating design proposals, workshops, digital design, marketing tests, and marketing activities guided by teachers and mentors from a branded ceramic workshop. The research findings demonstrate that the interdisciplinary curriculum facilitates knowledge innovation and fosters the development of students' professional skills, creativity, and problem-solving skills. The study also highlights the importance of stable scaffolding, including artefact, peer, and teacher support, which significantly contributes to cultivating transformational competencies, as outlined in the 2030 OECD Learning Compass. Additionally, the collaboration with Shanshing Four Seasons Celadon Studio on a patented ceramic product, "Funny Monkey," is a tangible example of the journey towards a triple-helix knowledge economy. This research underscores the importance of interdisciplinary curricula in promoting knowledge innovation and integrating transformational competencies in education. Scaffolding theory provides practical guidance for student learning and teaching strategies, presenting a sustainable roadmap for developing interdisciplinary curricula and offering a concrete and transferable pedagogical prototype for educational innovation.

Arid- and semi-arid Central Asia is particularly sensitive to climate change. The changes in extreme precipitation in Central Asia stemming from climate warming are the subject of intense debate within the scientific community. This study employed a Morlet wavelet analysis to examine the annual occurrence number of extreme precipitation in Central Asia from May to September during the period of 1951–2005. Their modulating planetary-scale climate modes were identified by using a linear regression analysis. Two major scales of the temporal variability were derived: 2–3.9 yr and 4–6 yr. The dominant variability was 2–3.9-yr scale and was associated with the negative phase of the Polar/Eurasia (POL) pattern. The 4–6-yr scale provided a secondary contribution and was closely linked to the negative phase of the North Atlantic Oscillation (NAO). These planetary climate modes acted as precursors of extreme precipitation over Central Asia. The negative phase of POL directly contributed to a negative height anomaly over Central Asia, which was intimately related to extreme precipitation. In contrast, the negative NAO phase possibly manifested as a Rossby wave source, which was subsequently exported to Central Asia through a negative–positive–negative Rossby wave train.

Structural health monitoring has been studied by a number of researchers as well as various industries to keep up with the increasing demand for preventive maintenance routines. This work presents a novel method for reconstruct prompt, informed strain/stress responses at the hot spots of the structures based on strain measurements at remote locations. The structural responses measured from usage monitoring system at available locations are decomposed into modal responses using empirical mode decomposition. Transformation equations based on finite element modeling are derived to extrapolate the modal responses from the measured locations to critical locations where direct sensor measurements are not available. Then, two numerical examples (a two-span beam and a 19956-degree of freedom simplified airfoil) are used to demonstrate the overall reconstruction method. Finally, the present work investigates the effectiveness and accuracy of the method through a set of experiments conducted on an aluminium alloy cantilever beam commonly used in air vehicle and spacecraft. The experiments collect the vibration strain signals of the beam via optical fiber sensors. Reconstruction results are compared with theoretical solutions and a detailed error analysis is also provided.

Traditional lithium-ion batteries cannot meet the high flexibility and bendability requirements of modern flexible electronic devices due to the limitations of their electrode materials. Therefore, the development of high-performance flexible energy storage devices is of great significance for promoting flexible electronics. In recent years, one-dimensional flexible fiber lithium-ion batteries have been rapidly developed due to the advantages of high flexibility and bendability. However, it is still a big challenge to realize 1D flexible fiber lithium-ion batteries with excellent electro-chemical properties and good mechanical performance. In this work, a reduced graphene ox-ide-based printing ink is proposed to fabricate flexible Li4Ti5O12/graphene fiber electrodes through a 3D printing assembly strategy. It is noteworthy that the green reducing agent vitamin C was used to reduce graphene oxide in one step, which improved the conductivity of the fiber elec-trode. Furthermore, a 3D conductive network is constructed inside the fiber electrodes due to the high specific surface area of reduced graphene oxide, which enhances the electronic conductivity and ion mobility. The fiber electrode not only has good mechanical performance, but also has ex-cellent electrochemical properties. Equally important, the method is simple and efficient, and the working environment is flexible. It can precisely control the shape, size and structure of the one-dimensional fiber flexible electrode, which is of great significance for the development of fu-ture flexible electronic devices.

GaN ultraviolet photodetector with metal-semiconductor-metal structure is achieved by growing on a periodic trapezoid column-shape patterned sapphire substrate using metalorganic chemical vapor deposition. Under 5-V reverse bias, the photodetector fabricated on such patterned sapphire substrate exhibits a lower dark current, a higher photocurrent, and a 476 % enhancement in the maximum responsivity as compare with those of the photodetector fabricated on conventional flat sapphire substrate. It is also found that the much larger UV-to-visible rejection ratio and the fact that responsivity drops in a smaller cut-off region are observed from photodetector fabricated by using a periodic trapezoid column-shape patterned sapphire substrate. These phenomena may all be attributed to the reduction of threading dislocation density and the improved quality of GaN film, as well as the internal reflection and/or scattering effect on the interface between GaN film and the periodic trapezoid column-shape pattern of the substrate.

Brain-stimulation reward, also known as intracranial self-stimulation (ICSS), is a commonly used procedure for studying brain reward function and drug reward. In electrical ICSS, an electrode is surgically implanted into the medial forebrain bundle in the lateral hypothalamus or the ventral tegmental area in the midbrain. Operant lever responding leads to the delivery of electrical pulse stimulation. The alteration in the stimulation frequency-lever response curve is used to evaluate the impact of pharmacological agents on brain reward function. If a test drug induces a leftward or upward shift in the ICSS response curve, it implies a reward-enhancing or abuse-like effect. Conversely, if a drug causes a rightward or downward shift in the functional response curve, it suggests a reward-attenuating or aversive effect. A significant drawback of electrical ICSS is the lack of cellular selectivity in understanding the neural substrates underlying drug reward versus aversion. Excitingly, recent advancements in optical ICSS (oICSS) have facilitated the development of at least three cell type-specific oICSS models – dopamine-, glutamate-, and GABA-dependent oICSS. In these new models, a comparable frequency-rate response curve has been established and employed to study the substrate-specific mechanisms underlying brain reward function and a drug's rewarding versus aversive effects. In this review article, we summarize recent progress in this exciting research area. The findings in these new behavioral models have not only increased our understanding of the neural mechanisms underlying drug reward and addiction but have also introduced a novel experimental approach in preclinical medication development for treating substance use disorders.

Pea shoots is a popular vegetable in certain regions of the world due to their unique taste and abundance of health-promoting phytochemicals. The perishable nature and susceptibility of root rot of pea shoots necessitate a new soilless production system located close to the market. This study compared the growth of pea shoots using various cultivation methods in LED plant factory. The results showed that early topping (4 days after transplanting, ET) promoted early harvest compared to later topping (20 days after transplanting, LT) and increased the number of harvested shoots by extending the harvest time to 2.8 times, ultimately resulting in a substantial yield improvement. Moreover, the yield of ET with lower planting density (72 plants m-2, ET-LD) was 8.7% higher than ET with higher planting density (126 plants m-2, ET-HD). Particularly, the average fresh weight of individual pea shoots under ET-LD exceeded that of ET-HD by 48.9%. It is advisable to consider adopting ET-LD for the cultivation of pea shoots in LED plant factory. Based on ET-LD, the yield, nutritional quality, and light use efficiency of pea shoots were further explored at different stages under three levels of light intensity (50, 100, 150 μmol m-2 s-1). Contrasted against the light intensity of 50 μmol m-2 s-1, the average fresh weight per pea shoots, number of harvested, and total fresh yield under light intensity of 150 μmol m-2 s-1 treatment increased by 60.2%, 62.8%, and 165.1%, respectively. Meanwhile, the fresh weight per pea shoots, photosynthetic capacity, soluble sugar and vitamin C levels in leaves, as well as light use efficiency and photon yield, initially increased and then decreased with the extension of the planting period. Among these, soluble sugar, LUE, and PY started to decrease after reaching the maximum value at 60-70 days after transplanting. In conclusion, light intensity of 150 μmol m-2 s-1 with a photoperiod of 16 h d-1 using LEDs, combined with early topping within a planting period of 60-70 days, proves to be suitable for the hydroponic production of pea shoots in LED plant factory.

Base on building information modeling(BIM) plus with Robotic process automation (RPA) technology is rapid development in smart building operations and maintenance (O&M). RPA is a workflow-based automated execution tool that is particularly well suited for replacing manual execution of simple and repetitive tasks using computer systems. The use of RPA technology can saves man-hours and increases productivity, which is important for the automation of building operations and maintenance operations.. The BIM technology, as an advanced technology in the construction industry, it can provide new ideas and methods for building operation and maintenance based on its visualization characteristics. That’s integrating RPA with BIM technology which will enhance the digitalization and virtualization of smart building operation and management. In this article will first introduce the features of RPA and BIM technology and then discuss the technical roadmap for remote automated operation and maintenance of smart building equipment room to implemention a low-cost and high efficient building equipment room operation and maintenance solution.

Considering the significance of thermodynamic cycles in the global energy system, it is necessary to develop new general classes of thermodynamic cycles to relieve current energy and environmental problems. Inspired by the relationship between power cycles and refrigeration cycles, we realize that general classes of thermodynamic cycles should occur in pairs with opposite functions. Here we reverse class 1 heating cycles to obtain another new general class of thermodynamic cycles named class 2 heating cycles (HC-2s). HC-2s have two basic forms, and each contains six thermodynamic processes. HC-2s present the simplest and most general approach to utilizing the temperature difference between a medium-temperature heat source and a low-temperature heat sink to achieve efficient high-temperature heating. HC-2s fill the gaps that have existed since the origin of thermal science, and they will play significant roles in the global sustainable energy system.

Thermodynamic cycles are not only the core concepts of thermal science, but also key approaches to energy conversion and utilization. So far, power cycles and refrigeration cycles have been the only two general classes of thermodynamic cycles. While diverse types of systems have been developed to perform thermodynamic cycles, no new general classes of thermodynamic cycles have been proposed. Based on the basic principles of thermodynamics, here we propose and analyze a new general class of thermodynamic cycles named class 1 heating cycles (HC-1s). Two basic forms of HC-1s are obtained by connecting six essential thermodynamic processes in the proper order and forming a thermodynamic cycle. HC-1s present the simplest and most general approach to utilizing the temperature difference between a high-temperature heat source and a medium-temperature heat sink to achieve efficient medium-temperature heating and/or low-temperature cooling. HC-1s fill the gaps that have existed since the origin of thermal science, and they will play significant roles in energy conservation and emission reduction.

The growing shortage of human resources to manage landscape in the water environment has led to problems concerning preservation of the landscape in Japan. To cultivate people with awareness about preserving the landscape, it is important to understand the process of how a region’s residents develop an attachment toward the water environment in their area. This paper identified factors influencing the attachment of residents toward the Fukushima-gata lagoon, Niigata prefecture, Japan, as a case study while focusing on changes in the lifestyle of the regional residents. The findings are as follows: (1) The target households frequently used Fukushima-gata lagoon for “fishing and for picking edible wild plants” and “gathering reeds to make thatched roofs” before “the reclamation project was carried out by the government in Fukushima-gata lagoon.” They also frequented Fukushima-gata lagoon for “walking and cherry blossom viewing” after “the reclamation project” was implemented. (2) Even the fact that distance from the lagoon to their place of residence increased after the project did not lose their attachment to the lagoon. (3) It was suggested that the project contributed to increase the attachment of regional residents towards Fukushima-gata lagoon because of multiple factors such as “playing in the water,” “livelihood opportunity,” “recreational use,” and so on. (4) Changes in the attachment of regional residents toward Fukushima-gata lagoon before and after the reclamation project was carried out by the government corresponded to “changes in the lifestyle of the local residents” before and after the project.

Postprandial glucose levels between 4 and 7.9 hours (PPG4–7.9h) correlate with mortality from various diseases including hypertension, diabetes, cardiovascular disease, and cancer. This study aimed to assess if predicted PPG4–7.9h could diagnose diabetes. Two groups of participants were involved: Group 1 (4420 participants) had actual PPG4–7.9h, while Group 2 (8422 participants) lacked this measure but had all the diabetes diagnostic measures. Group 1 underwent multiple linear regression to predict PPG4–7.9h using 30 predictors, achieving accuracy within 11.1 mg/dL in 80% of the participants. Group 2 had PPG4–7.9h predicted using this model. Receiver operating characteristic curve analysis showed that predicted PPG4–7.9h could diagnose diabetes with an accuracy of 87.3% in Group 2, with a sensitivity of 75.1% and specificity of 84.1% at the optimal cutoff of 102.5 mg/dL. Simulation on 10,000 random samples from Group 2 revealed that 175 participants may be needed to investigate PPG4–7.9h as a diabetes diagnostic marker with a power of at least 80%. In conclusion, predicted PPG4–7.9h appears to be a promising diagnostic indicator for diabetes. Future studies seeking to ascertain its definitive diagnostic value might require a minimum sample size of 175 participants.

Impact of land use and land cover (LULC) change on soil erosion is still imperfectly understood, especially in northeastern China (NEC). Based on the Revised Universal Loss Equation (RUSLE), the variability of soil erosion at different spatial scales following land use changes in1980, 1990, 2000, 2010, and 2017 was analyzed. The regionally spatial patterns of soil loss coincided with the topography, rainfall erosivity, soil erodibility, and use patterns, and around 45% soil loss came from arable land. Regionally, soil erosion rates increased from 1980 to 2010 and decreased from 2010 to 2017, ranging from 3.91 to 4.45 t ha-1 yr-1 with an average of 4.22 t ha-1 yr-1 in 1980-2017. The rates of soil erosion less than 1.41 t ha-1 yr-1 decreased from 1980 to 2010, and increased from 2010 to 2017, and opposite changing patterns occurred in higher erosion classes (i.e., above 5 t ha-1 yr-1). At a provincial scale, Liaoning Province experienced the highest soil erosion rate of 9.43 t ha-1 yr-1, followed by Jilin Province, the east Inner Mongolia, and Heilongjing Province. Arable land continuously increased at the expense of forest in the high-elevation and steep-slope areas from 1980 to 2010, and decreased from 2010 to 2017, resulting in increased areas with erosion rates higher than 7.05 t ha-1 yr-1. At a county scale, around 75% of the countries had soil erosion rate higher than its tolerance level. The county numbers with higher erosion rate increased in 1980-2010 and decreased in 2010- 2017, resulting from the sprawl and withdrawal of arable land. The results indicate that appropriate policies can control soil loss through limiting arable land sprawl in areas of unfavorable regions in the NEC.

Energy resources are important sources of social and economic development, human survival and security. However, energy resources are objective and scarce, especially the fossil energy, such as coal, oil, natural gas, etc. Human survival environment is increasingly damaged, and the condition of energy is also gradually becoming deficient, so it is necessary to develop new energy resources to meet the increasing demand of material civilization. Solar energy can meet the needs of human development in the future as a kind of clean resource and it has been concerned by all countries in the world. We analyzed the effectiveness of subsidies to the PV industry of both the price and R&D by the spatial econometric model. In some region, the production capacity of photovoltaic industry has shown a significant spatial agglomeration situation in China since 2012. At the same time, benchmarking price and R&D subsidies played a positive incentive to the photovoltaic industry production capacity. It is a certain degree of inverse correlation between the scale of policy subsidies and the resource endowment of solar resources. Therefore, the countermeasures should be considered from the aspects of institutions, industry, technology and public financial policies.

Deep learning has achieved lots of successes in many fields, but when trainable sample are extremely limited, deep learning often under or overfitting to few samples. Meta-learning was proposed to solve difficulties in few-shot learning and fast adaptive areas. Meta-learner learns to remember some common knowledge by training on large scale tasks sampled from a certain data distribution to equip generalization when facing unseen new tasks. Due to the limitation of samples, most approaches only use shallow neural network to avoid overfitting and reduce the difficulty of training process, that causes the waste of many extra information when adapting to unseen tasks. Euclidean space-based gradient descent also make meta-learner's update inaccurate. These issues cause many meta-learning model hard to extract feature from samples and update network parameters. In this paper, we propose a novel method by using multi-stage joint training approach to post the bottleneck during adapting process. To accelerate adapt procedure, we also constraint network to Stiefel manifold, thus meta-learner could perform more stable gradient descent in limited steps. Experiment on mini-ImageNet shows that our method reaches better accuracy under 5-way 1-shot and 5-way 5-shot conditions.

High dimensional statistical analysis for the yield of large-scale circuits is quite difficult due to expensive simulations, especially for the memory circuits with high sigma requirement (e.g., SRAM). In this paper, we developed an efficient sparse additive model to substitute simulations. To fit high sigma region accurately, the modeling center is moved to near failure boundary searched by scaling the shape of sampling function. To solve the model efficiently, the process variables are grouped by standard cells so that the model can be solved by our developed blockwise greedy algorithm. The experiments on the 28nm memory circuits validate that our method achieves high accuracy and efficiency compared with other state-of-art works.

This study aimed to identify miRNA editing sites during adipose tissue development in Ningxiang pigs and analyze their characteristics and functions. Based on the small RNA-seq data from subcutaneous adipose tissue samples of Ningxiang pigs at four stages (30, 90, 150 and 210 days), we constructed a developmental atlas of the miRNA editome in adipose tissue of Ningxiang pigs. The characteristics and functions of this editome were further explored through bioinformatics analysis. The findings revealed that a total of 505 miRNA editing sites were identified with C-to-U editing types being the most prevalent, followed by U-to-C, A-to-G and G-to-U. Importantly, these four types of miRNA editing exhibited a base preference. The number of editing sites showed obvious differences among age groups, with the highest occurrence of miRNA editing events observed at 90 days of age and the lowest at 150 days of age. In the miRNA seed region, a total of 9 miRNA editing sites were identified with significant differences in editing levels (P &lt; 0.05), and located in ssc-miR-23a, ssc-miR-27a, ssc-miR-30b-5p, ssc-miR-15a, ssc-miR-497, ssc-miR-15b, and ssc-miR-425-5p, respectively. Target gene prediction and enrichment analysis revealed that the editing of miR-497 may potentially regulate fat deposition by inhibiting adipose synthesis via influencing target binding. These results provide new insights into the regulatory mechanism of pig fat deposition.

The advancement in science and technology has led to luffa sponge (LS) being widely used as a natural material in industrial application as its polyporous structure and light texture. In order to enhance the utility of LS fibers as the reinforcement of lightweight composite materials, this study investigate its water absorption, mechanical properties, anatomical characteristic and thermal performance. Hence, moisture regain, tensile properties of LS fiber bundles were measured in accordance with standards and the structural characteristics were investigated via microscopic observation. Scanning electron microscopy (SEM) was used to observe the surface morphology and fracture surface of fiber bundles. Test results shows that the special structure where the phloem tissues degenerate to cavities had a significant influence on the mechanical properties of LS fiber bundles. Additionally, the transverse sectional area occupied by fibers in a fiber bundle (SF), wall thickness and ratio of wall to lumen of fiber cell, and crystallinity of cellulose had an impact on the mechanical properties of LS fiber bundles. Furthermore, the fiber bundles density of LS varies range of 385.46-468.70 kg/m³, much less than that of jute (1360.40 kg/m³) and Arenga engleri (950.20 kg/m³) while LS fiber bundles has superior specific modulus.

To explore the relevant factors that affect the efficacy of consciousness-regaining therapy (CRT)for prolonged disorder of consciousness(pDOC),a retrospective analysis was conducted on the case data of 114 patients with pDOC admitted to department of functional neurosurgery of Tianjin Huanhu Hospital from January 2019 to January 2022. Basic information on the cases,data on pDOC disease assessment, consciousness-regaining therapy methods, and efficacy evaluation were collected. A total of 114 patients were grouped and compared based on the efficacy at the end of treatment. Among them, there were 61 cases in the ineffective group and 53 cases in the effective group. There was no statistically significant difference (P&gt;0.05) between the two groups in terms of gender, age, etiology, acute cerebral herniation, emergency craniotomy surgery, emergency decompressive craniectomy, time from onset to start of consciousness-regaining therapy , and duration of consciousness-regaining therapy(P&gt;0.05). However, there were statistically significant differences (P&lt;0.05) in terms of secondary hydrocephalus, , consciousness-regaining therapy methods, CRS-R grading before treatment, and GOSE score at 6 months after treatment. Binary logistic regression analysis showed that the type of therapy (OR=0.169, 95% CI: 0.057-0.508) was a related factor affecting the efficacy of consciousness-regaining therapy (P&lt;0.05).Compared with non-invasive therapy, personalized awakening therapy using various invasive consciousness-regaining therapy methods can help improve the efficacy of therapy for pDOC.

Commercial classification is essential to spatially describe commerce. Although most of the proposed classifications have been classic functional analyses, rooted on qualitative studies, some recent classifications efforts are found to rely heavily on more quantitative methods, due eventually to increasing data availability and technological advancements. In this paper, a classification is proposed, using k-means clustering and a minimal set of variables (density, diversity and clustering) to derive the commercial structure of Lisbon. The classification is implemented for 1995, 2002 and 2010, using a 150m-sided square grid. The cross-sectional analysis of the results shows the rise of shopping-malls against city centre decline and gentrification, along with changes in cluster composition considering 9 different commercial categories (6 categories of retail, and restaurants, cafes and bars). These findings are in line with literature, thus supporting the obtained classification. Since the classification can be used to accurately describe the commercial structure of the city in different time periods, it is implied that it may also be generalized to different cities. Furthermore, the potential use of cluster membership in retail location models, which is an advantage of the proposed classification, could help strengthen the relationship between location modelling and commercial classification, thus reinforcing the role of commercial studies in urban planning and policymaking.

Bacterial biofilms can cause widespread infection. In addition to causing urinary tract infections and pulmonary infections in patients with cystic fibrosis, biofilms can help microorganisms adhere to the surfaces of various medical devices, causing biofilm-associated infections on the surfaces of biomaterials such as venous ducts, joint prostheses, mechanical heart valves, and catheters. Biofilms provide a protective barrier for bacteria and provide resistance to antimicrobial agents, which increases the morbidity and mortality of patients. This review introduces the formation process and drug resistance mechanism of biofilms in detail, and further summarizes the main characteristics of clinical persistent infection caused by biofilms and the many methods of treating biomaterial-related biofilm. This provides ideas and directions for the development of new biofilm infection strategies related to therapeutic materials.

For solving the fractional differential equations in computational fluid dynamics (CFD), it’s complicated and difficult by the Laplace and Fourier transforms. Based on the Caputo fractional derivative, the analytical solutions for unsteady unidirectional flows of a generalized Oldroyd-B fluid are deduced by the separation of variables method. Results show that the analytical solutions are given easily, and have good university. For some specific parameter values, the well-known analytical solutions for the generalized second grade fluid, the generalized Upper-Convected Maxwell (UCM) fluid as well as the ordinary Oldroyd-B fluid can be obtained.

Infrared thermography has already been proven to be a significant method in non-destructive evaluation since it gives information with immediacy, rapidity, and low cost. However, the thorniest issue for the wider application of IRT is quantification. In this work, we proposed a specific depth quantifying technique by employing the Gated Recurrent Units (GRU) in composite material samples via pulsed thermography (PT). Finite Element Method (FEM) modeling provides the economic examination of the response pulsed thermography. In this work, Carbon Fiber Reinforced Polymer (CFRP) specimens embedded with flat bottom holes are stimulated by a FEM modeling (COMSOL) with precisely controlled depth and geometrics of the defects. The GRU model automatically quantified the depth of defects presented in the stimulated CFRP material. The proposed method evaluated the accuracy and performance of synthetic CFRP data from FEM for defect depth predictions.

Markov chain Monte Carlo sampling propagators, including numerical integrators for stochastic dynamics, are central to the calculation of thermodynamic quantities and determination of structure for molecular systems. Efficiency is paramount, and to a great extent, this is determined by the integrated autocorrelation time (IAcT). This quantity varies depending on the observable that is being estimated. It is suggested that it is the maximum of the IAcT over all observables that is the relevant metric. Reviewed here is a method for estimating this quantity. For reversible propagators (which are those that satisfy detailed balance), the maximum IAcT is determined by the spectral gap in the forward transfer operator, but for irreversible propagators, the maximum IAcT can be far less than or greater than what might be inferred from the spectral gap. This is consistent with recent theoretical results (not to mention past practical experience) suggesting that irreversible propagators generally perform better if not much better than reversible ones. Typical irreversible propagators involve a parameter controlling the mix of ballistic and diffusive movement. To gain insight into the effect of the damping parameter for Langevin dynamics, its optimal value is obtained here for a multidimensional quadratic potential energy function.

As a widely used plastic, the aging and degradation of polyethylene (PE) are inevitable problems, whether the goal is to prolong the life of PE products or address the issue of white pollution. Molecular simulation is a vital scientific tool in elucidating the mechanisms and processes of chemical reactions. To obtain the distribution and evolution process of PE's thermal oxidation products, this work employs the self-consistent charge density functional tight binding (SCC-DFTB) method to perform molecular simulations of the thermal oxidation of PE with different crystallinity and branched structures. We discovered that crystallinity does not affect the thermal oxidation mechanism of PE, but higher crystallinity makes PE more susceptible to cross-linking and carbon chain growth, reducing the degree of PE carbon chain breakage. The branched structure of PE results in differences in pore size between the carbon chains, with larger pores leading to a concentrated distribution of O2 and free radicals subsequently formed. The breakdown of PE is slowed down when free radicals are localized in low-density regions of the carbon chain. The specifics and mechanism of PE's thermal oxidation are clearly revealed in this paper, which is essential for understanding the process in-depth and for the development of anti-aging PE products.