Neuroendocrine prostate cancer (NEPC) is a highly aggressive subtype of prostate cancer (PC) that commonly emerges through a transdifferentiation process from prostate adenocarcinoma and evades conventional therapies. Extensive molecular research has revealed factors that drive lineage plasticity, uncovering novel therapeutic targets to be explored. A diverse array of targeting agents is currently under evaluation in pre-clinical and clinical studies with promising results in suppressing or reversing the neuroendocrine phenotype and inhibiting tumor growth and metastasis. This new knowledge has the potential to contribute to development of novel therapeutic approaches that may enhance clinical management and prognosis of this lethal disease.

Structural health monitoring (SHM) is critical for ensuring the safety of infrastructures like bridges. This article presents a digital twin solution for SHM of railway bridges using low-cost wireless accelerometers and Machine Learning (ML). The system architecture combines edge on-premises computing and cloud analytics to enable efficient real-time monitoring and complete storage of relevant time-history datasets. After train crossings, accelerometers stream raw vibration data, which is processed in the frequency domain and analyzed via machine learning to detect anomalies indicating potential structural issues. The digital twin approach is demonstrated on an in-service railway bridge, where vibration data was collected over two years under normal operating conditions. By learning allowable ranges for vibration patterns, the digital twin model identifies abnormal spectral peaks, suggesting changes in structural integrity. The long-term pilot proves that this affordable SHM system can provide automated and real-time warning of bridge damage and also supports the use of in-house designed sensors of lower-cost and edge computing capabilities than those used in the demonstration. The successful on-premises-cloud hybrid implementation provides a cost effective and scalable model for expanding monitoring to thousands of railway bridges, democratizing SHM to improve safety by avoiding catastrophic failures.

Introduction: Catecholaminergic polymorphic ventricular tachycardia (CPVT) is a rare cardiac ion channelopathy. This study examined the clinical characteristics, genetic basis, and arrhythmic outcomes of CPVT patients from China. Methods: PubMed and EMBASE were systematically searched for case reports or series reporting on CPVT patients from China until February 19th, 2022 using the keyword “Catecholaminergic Polymorphic Ventricular Tachycardia” OR “CPVT”, with the location limited to “China” OR “Hong Kong” or “Macau” in EMBASE, with no language or publication type restriction. Clinical characteristics, genetic findings, and primary outcome of spontaneous ventricular tachycardia/ventricular fibrillation (VT/VF) were analyzed. Results: A systematic search of the PubMed and Embase databases yielded 1049 and 47 articles, respectively. After the exclusion of overlapping cohorts, a total of 58 unique cases from 15 studies (median presentation age: 8 [5.0-11.8] years old) were included. All patients except for one presented at or before 19 years of age. 56 patients (96.6%) were initially symptomatic. Premature ventricular complexes (PVCs) were present in 44 of 51 patients (86.3%) and VT in 52 of 58 patients (89.7%). Genetic tests were performed on 54 patients (93.1%) with a yield of 87%. RyR2, CASQ2, TERCL, and SCN10A mutations were found in 35 (71.4%), 12 (24.5%), one (0.02%) patient, and one patient (0.02%) respectively. 54 patients were treated with beta-blockers, eight received flecainide, five received amiodarone, two received verapamil and one received propafenone. Sympathectomy (n=10) and implantable-cardioverter defibrillator implantation (n=8) were performed. On follow-up, 13 patients developed VT/VF. Conclusion: This is the first systematic review of CPVT patients from China. Most patients had symptoms on initial presentation, with syncope as the presenting complaint. RyR2 mutation accounts for more than half of the CPVT cases, followed by CASQ2, TERCL and SCN10A mutations.

Introduction: Catecholaminergic polymorphic ventricular tachycardia (CPVT) is a rare cardiac ion channelopathy. The aim of this study is to examine the genetic basis and identify predictive factors for arrhythmic outcomes of CPVT patients from China. Methods: PubMed and MedRxiv were systematically searched for case reports or case series reporting on CPVT patients from China. Clinical characteristics, genetic findings and primary outcome of spontaneous ventricular tachycardia/ventricular fibrillation (VT/VF) were analyzed. Results: A total of 56 (median presentation age=9 [6-13] years old) patients were included. All patients except for one presented at or before 19 years of age. Fifty-three patients (94.6%) were initially symptomatic. PVCs were present in 40 out of 45 patients (88.9%) and VT in 51 out of 56 patients (91.1%). Genetic tests were performed in 50 patients (89.3%). RyR2, CASQ2 and TERCL mutations were found in 32 (57.1%), 11 (19.6%) and one (0.02%) patients, respectively. Fifty patients were treated with beta-blockers, eight patients received flecainide, four patients received amiodarone, two received verapamil and one received propafenone. Sympathectomy (n=10) and implantable-cardioverter defibrillator implantation (n=7) were performed. On follow-up, 17 patients developed incident VT/VF. Conclusion: This is the first systemic review and meta-analysis of CPVT patients from China. Most patients had symptoms on initial presentation, and around a third had VT as the presenting complaint. RyR2 mutation accounts for more than half of the CPVT cases, followed by CASQ2 and TERCL mutations. Some of these mutations have not been hitherto reported outside of China. Most patients received β-blocker therapy. Around 18% had sympathectomy and 13% had ICDs implanted.

People living in areas of significant seismic risk seldom undertake sufficient preparations to safeguard their family. This is most problematic in remote communities such as those along the Dead Sea Fault, Israel, where self-reliance is a key factor in coping with disasters. To facilitate individual and familial involvement in earthquake preparedness in remote areas, we designed a tool for self-assessment of risk and preparedness. The personalized risk assessment is based on national hazard and building standards, and on personal input regarding structure characteristics. The risk and preparedness evaluations enhance awareness and provide immediate feedback to help users improve familial preparedness. Spatial analysis of the data collected is used to form high-resolution maps that expose specific challenges for emergency response. A study conducted in the town of Mitzpe Ramon exposed neighborhoods with relatively high risk of damage and low preparedness. Integrating these results with seasonal stress-factors such as peak tourism and extreme weather, provides new and important insights on the ability of the local community and emergency forces to cope with multi-hazard situations. Analysis of the heterogeneous distribution of expected hardship within a community should be implemented world-wide to improve risk mitigation.

Leishmaniasis in wild canids is a vector-borne disease caused in Europe by the protozoan parasite Leishmania infantum. To date, there is limited information on clinical signs and laboratory abnormalities in wolves due to leishmaniasis. The current clinical case report described a female Iberian wolf (Canis lupus signatus) housed in semi-captivity conditions at the Centro del Lobo Ibérico “Félix Rodríguez de la Fuente”, in Robledo de Sanabria, Zamora (Spain) with an interdigital ulcerous wound at the right forepaw, hyper-gammaglobulinemia, and abnormal liver blood parameters. Definitive serodiagnosis of leishmaniasis was established using antileishmanial serum antibodies and PCR analysis of different biological samples. A gold standard anti-L. infantum treatment protocol consisting in intramuscular meglumine antimoniate and oral allopurinol combination was installed. However, the presence of pain at the site of injection due to meglumine antimoniate administration forced its substitution by oral miltefosine. A progressive reduction of the levels of anti-L. infantum serum antibodies and the concentrations of gamma-globulin fraction was detected after antileishmanial treatment as well as a decline of liver GPT. To our knowledge, this is the first case of leishmaniasis diagnosed in a wolf housed in semi-captivity conditions treated and successfully cured.

The study was carried out in zone 7 of Ecuador, in ecosystems of the Southern Montane Evergreen Forest of the Eastern Cordillera of the Andes that goes from 2200 to 3000 masl. In the Evergreen Seasonal Lower Montane Forest of Catamayo-Alamor, which ranges from 1600-2000 meters above sea level and finally in the Semideciduous Foot Montane Forest of Catamayo-Alamor, which ranges from 400-1600 meters above sea level. The objective was to know the occurrence, structure and abundance of J. neotropica. The investigation consisted of collecting secondary information on the occurrence of the species, to later verify it in situ. Six sites with areas ≥ 0.5 hectares were identified, four in the province of Loja and two in the province of Zamora Chinchipe. Regarding the structure, it was determined that there are significant statistical differences as well as in the dasometric variables between one site and another, presenting better growths El Tundo with average values in DAP(cm)= 45.16; G(m2) = 1.41; HT(m)= 19.22; HC(m)= 13; VC(m3) = 3.55; VT(m3) = 5.22. Regarding the Morisita index, the species presents adistribution pattern >1. Regarding abundance, it was determined that Algeria presented a maximum of 297 (ind/ha), and La Victoria 46 (ind/ha) with a minimum.

Conditional heteroskedastic financial time series are commonly modelled by (G)ARCH processes. ARCH(1) and GARCH were recently established in C[0,1] and L^2[0,1]. This article provides sufficient conditions for the existence of strictly stationary solutions, weak dependence and finite moments of (G)ARCH processes for any order in C[0,1] and L^p[0,1]. It deduces explicit asymptotic upper bounds of estimation errors for the shift term, the complete (G)ARCH operators and the projections of ARCH operators on finite-dimensional subspaces. The operator estimaton is based on Yule-Walker equations, and estimating the GARCH operators also involves a result estimating operators in invertible linear processes being valid beyond the scope of (G)ARCH. Moreover, our results regarding (G)ARCH can be transferred to functional AR(MA).

The alcoholic fermentation process with agitation/static, followed by the acetic fermentation submerged in banana was evaluated. Kinetics parameters of alcoholic fermentation for the maximum ethanol/glycerol metabolites in agitated process was 29 and 27 h, and in static 47 and 45 h, respectively. For acetic fermentation, the kinetics parameters were medium time of 39.9 h, acetic acid yield of 53.1% and acetic acid productivity of 0.216 g/Lh. Wines from agitated/static process presented 5.73 and 6.81% (v/v) of alcohol content, respectively. Wine obtained by the static process presented higher concentrations of volatile compounds. The vinegar showed 49.2 g/L of acetic acid and the esters concentrations were higher than in wine. The wine and vinegar minerals were consistent with amount observed in the pulp, with an increase in sulphur concentration after alcoholic fermentation and decrease after acetic fermentation. Products showed chemical and composition of sensory and nutritional interest.

A major task in Functional Time Series Analysis is measuring the dependence within and between processes, for which lagged covariance and cross-covariance operators have proven to be a practical tool in well-established spaces. This article deduces estimators and asymptotic upper bounds of the estimation errors for lagged covariance and cross-covariance operators of processes in Cartesian products of abstract Hilbert spaces for fixed and increasing lag and Cartesian powers. We allow the processes to be non-centered, and to have values in different spaces when investigating the dependence between processes. Also, we discuss features of estimators for the principle components of our covariance operators.

Advanced derivatives of the CXCR4 antagonist EPI-X4 have shown therapeutic efficacy upon topical administration in animal models of asthma and dermatitis. Here, we studied plasma stability of the EPI-X4 lead compounds WSC02 and JM#21, using mass spectrometry to monitor the chemical integrity of the peptides and a functional fluorescence-based assay that determines peptide function in a CXCR4-antibody competition assay. Although mass spectrometry revealed a very rapid disappearance of both peptides in human plasma within seconds, the functional assay revealed a significantly higher half-life of 9 minutes for WSC02 and 6 minutes for JM#21, respectively. Further analyses demonstrated that WSC02 and JM#21 interact with low molecular weight plasma components and serum albumin. Albumin binding is mediated by the formation of a disulfide bridge between Cys10 in the EPI-X4 peptides and Cys34 in albumin. These covalently linked albumin-peptide complexes have a higher stability in plasma as compared to the non-bound peptides and retain the ability to bind and antagonize CXCR4. Remarkably, chemically synthesized albumin-EPI-X4 conjugates coupled by non-breakable bonds have a drastically increased plasma stability of over 2 hours. Thus, covalent coupling of EPI-X4 to albumin in vitro before administration or in vivo post administration may significantly increase the pharmacokinetic properties of the new class of CXCR4 antagonists.

Antibiotic resistance (ABR) is concerning issue due to its direct and indirect repercusions on public health, since decreased therapeutic effect of certain antibiotic to treatment complications that can cause death. There are several mechanism as to how ABR can be transferred from one microoorganisms to another, and many of them are dependant many environmental factors. The food supply chain is a environment in which ABR gene transfer can occur is multiple pathways, which generate concerns regarding food safety. Here, we summarize relevant mechanisms which are implied in ABR in food supply chain but also we are addressing routes of transmission and prevalence of ABR, implications on public health, and the application of new alternatives to antibiotics such as antimicrobial peptides, mainly bacteriocins, in order to countermeasure ABR.

The unstable international economic situation is reflected in the supply chain stress, lack or increased cost of some raw materials, fuel or semi-finished products is forcing organizations to perform new optimization initiatives in the utilization of their equipment and assets pointed to obtain the maximum value from them, while maintaining and even improving the quality of their products. The achievement of these objectives involves the reduction or minimization of equipment downtime to maintain the advantage over their competitors and ensure the organization's competitiveness. The intelligent maintenance system (IMS) provides adequate support for decision-making related to equipment maintenance, since poor maintenance results in unplanned stoppages, with the consequent additional cost and increased customer dissatisfaction, and an over-maintenance can result in an additional labor cost, time and the replacement of parts that are in good conditions. The utilization of new tools and technologies introduced by Industry 4.0 offers multiple opportunities for enhancement through communication and computerized data processing, aiming to improve the maintainability of a hydrogen compressor using neural networks based on attention mechanisms combined with linear regression.

Leaders are essential in encouraging and facilitating creative thinking among members of a group or organization. A leader must also monitor the group's initiatives to encourage innovation and fresh thinking. In this article, we take a look at the circumstances under which there is a link between leadership and original problem-solving. Thirty separate studies served as the basis for this sample. Many of these analyses see leadership independently from the concept of innovation. Both moderating and mediating factors were discussed, and two additional factors were identified for which no firm conclusions could be drawn. This investigation reveals three new potential mediators or moderators of the connection between leadership and inventiveness.

Raw material logistics reflects an important aspect of global trade. Raw materials form an essential basis for society, for daily life, and range from apples to zinc. This paper addresses the analysis and optimization of supply chains of raw materials in terms of their economic viability and their sustainability. Type representatives are chosen according to annual transported quantities. Hard coal represents bulk goods, aluminum primary raw materials with medium quantities, and rare earths primary raw materials with small quantities. Their respective supply chains are analyzed and subsequently possible strategies and methods and their application are discussed. The paper shows for the first time that the selection and application of optimization priorities (e.g. profitability or sustainability) depends on the primary raw material and its integration into global production chains.

In this paper we use the Mellin convolution theorem, which is related to Perron's formula. Also we introduce new explicit formulae for arithmetic function which generalize the explicit formulae of Weil for other arithmetic functions different from the Von-Mangoldt function.

In response to the growing challenges in drone security and airspace management, this study introduces an advanced drone classifier, capable of detecting and categorizing Unmanned Aerial Vehicles (UAVs) based on acoustic signatures. Utilizing a comprehensive database of drone sounds across EU-defined classes (C0 to C3), this research leverages machine learning (ML) techniques for effective UAV identification. The study primarily focuses on the impact of data augmentation methods—pitch shifting, time delays, harmonic distortion, and ambient noise integration—on classifier performance. These techniques aim to mimic real-world acoustic variations, thus enhancing the classifier's robustness and practical applicability. Results indicate that moderate levels of augmentation significantly improve classification accuracy. However, excessive application of these methods can negatively affect performance. The study concludes that sophisticated acoustic data augmentation can substantially enhance ML-driven drone detection, providing a versatile and efficient tool for managing drone-related security risks. This research contributes to UAV detection technology, presenting a model that not only identifies but also categorizes drones, underscoring its potential for diverse operational environments.

Nowadays Air-Source Heat Pumps (ASHP) in combination with a Photovoltaic (PV) installation are a very promising option for a necessary and urgent energy transformation in European Union (EU). It is extremely important to develop solutions that will help maximize the use of energy generated from renewable energy sources (RES). Such issues include the problem of insufficient use of generated electricity in PV on-grid microinstallations in residential buildings. This paper's aim is to analyze the results of one-year-round operation of a PV array grid-connected hybrid installation with ASHP for domestic hot water (DHW) preparation in a residential building in Cracow, Poland in the context of increasing self-consumption (SC) of PV energy. Models of systems are built and simulated in Transient System Simulation Tool 18 (TRNSYS) software. Simulations were carried out for different scenarios involving different building electricity consumption profiles, PV system capacity and specified runtime management of ASHP. The novelty of this study lies in the evaluation of the impact of a certain range of conditions on the energy performance of the system, in particular on SC. The results showed that the use of ASHP, with specified runtime management, results in an increase in monthly SC values from 7 to 18%, and annual SC values up to 13%. Also determining the appropriate size of the used PV system depending on whether it is present ASHP in the installation is crucial to increase the value of the SC parameter. Overall, this study provides valuable insights into the potential benefits of PV panels and ASHP operating together, in particular on SC values.

The international literature shows a polarised debate on the impacts of climate change on migration. Some studies find a positive linkage, whereas others find a negative one. It is, without a doubt, a complex process better considered case-specific. There is no available information on the relationship between climate change and migration in Colombia, despite past research exploring each of these subjects independently. This study intends explicitly to investigate this linkage gap. Consequently, this paper's essential contribution is that it builds a bridge between climate change scenarios and migratory science for the first time in Colombia. Despite their limitations, the theoretical and methodological framework suggested by IOM (2009b pp. 86, Section B, Chapter II) is demonstrated in this study to be very valid since it provides a methodology to predict where future flows will occur (based on past evidence). The methodological approaches of SLA and NELM explained in section A in the IV Chapter are also valuable for analysing and approaching this study's conclusions. The primary conclusions of this study indicate that the "Coffee Region," Valle, and Atlantic (or Caribbean Coast) provinces that mainly send emigrants to Spain and the US are the key internal regions responsible for most of the international migration from Colombians. The same areas are especially vulnerable to the impacts of upcoming climate change in the A1B scenario produced by the IDEAM (2010) for 2040 and 2100. Thus, future flows of migrants are expected from these regions (2040-2100). However, issues such as visa requirements or the costs associated with migration constitute international barriers to this flow. The sensitivity of these regions can also be associated with internal migration flows, more armed conflict, and forced displacement in a cyclical process. Theoretically, a resurgence of Colombia's armed conflict and displacement due to climate change can be expected. However, the need for empirical studies in Colombia to support this analysis is imperative and is the most crucial recommendation arising from this study.

Energy poverty is a severe electrification challenge in Nigeria that has affected the country's economic development. The gap between electricity demand and supply continues to increase, and a large percentage of the populace affected are rural dwellers. With the prevailing electricity inaccessibility in rural, renewable energy sources (RES) present viable option for addressing rural electrification challenge. However, RES like solar have intermittency challenges since they are weather dependent. Thus, a hybrid microgrid system (HMS) comprising solar, hydropower and battery storage was sized as a feasible solution for electrifying rural areas in Nigeria. For the HMS sizing, a site was selected, whose residential load demand was estimated. The renewable energy generation potential for the selected resources at the site as well as grid reliability were assessed. Hybrid Optimisation Model for Multiple Energy Resources (HOMER) was used to size the HMS. An economic analysis was performed to determine the levelised cost of energy (LCOE) and net present cost (NPC). For the sized HMS, two scenarios were considered: off-grid and grid-connected HMS configurations. The results showed that the LCOE of the off-grid and grid-connected configurations are $0.101/kWh and $0.046/kWh, respectively. The NPC of the off-grid and grid-connected configurations are $227,307 and $145,282, respectively.

In the 21st century, museums have come to realize that the human skeletons they display might have problematic origins. The older anthropological skeletal collections typically originate from anatomical dissection of the executed and the very poor, or from scavenged graves of indigenous people. Such collections are currently being re-evaluated in many countries, and reburying or repatriating museum skeletons have become viable options. A particularly difficult question is what to do with human remains of unknown origins. Here, we present and discuss one such case, where a human skeleton of unclear origin in the 1930’s was brought to a local museum in Bollnäs, Sweden, under likely unethical circumstances. Most of the bones have now been lost, except for the skull, the sacrum and one lumbar vertebra, which in 2007 were transferred to the Museum of Ethnography in Stockholm. The skull was there put on display as the “Bollnäs skull”, and was presented to the public to illustrate the dilemmas involved in handling human remains in the post-colonial era. The original gift letter from 1934 stated that the skeleton came from San Nicolas Island outside the California coast, but this letter contained numerous instances of incorrect information and was therefore deemed not trustworthy. However, our critical examination of the skull and its background information indicates that San Nicolas Island is a plausible origin, and we suggest that a bioarchaeological comparison should be made between the skull and living descendants of the San Nicolas Island population, and/or with archaeological human skeletons excavated from the island.

There is an international concern for reducing energy consumption and protecting the environment in the construction industry. The energy efficiency of a building depends on the thermal resistance of concrete, and utilizing concrete products with elevated thermal resistance can enhance this aspect. This study analyzes the impact of perlite, as an addition, on the physico-mechanical properties of concrete, with the aim of identifying perlite concrete products that will respond to the improvement of the heat transfer resistance of the building envelope. The study examines the effect of replacing different amounts of concrete aggregates with perlite in percentages of 10%, 20%, 30%, and 100%. The results show that substituting sand with perlite improves the thermal performance of concrete, but its mechanical properties are negatively affected. The research carried out highlighted that perlite can be successfully introduced in the production of concrete blocks used for external non-bearing wall panels, the outstanding feature being the reduction of energy consumption in buildings. Overall, the paper identifies an efficient and environmentally friendly way of using perlite in the construction industry, enhancing the energy efficiency of buildings while minimizing the environmental footprint caused by the construction industry.

Multiobjective optimization plays an increasingly important role in modern applications, where several criteria are often of equal importance. The task in multiobjective optimization and multiobjective optimal control is therefore to compute the set of optimal compromises (the Pareto set) between the conflicting objectives. The advances in algorithms and the increasing interest in Pareto optimal solutions have led to a wide range of new applications related to optimal and feedback control which results in new challenges such as expensive models or real-time applicability. Since the Pareto set generally consists of an infinite number of solutions, the computational effort can quickly become challenging which is particularly problematic when the objectives are costly to evaluate or when a solution has to be presented very quickly. This article gives an overview over recent developments in accelerating multiobjective optimal control for complex problems where either PDE constraints are present or where a feedback behavior has to be achieved. In the first case, surrogate models yield significant speed-ups. Besides classical meta-modeling techniques for multiobjective optimization, a promising alternative for control problems is to introduce a surrogate model for the system dynamics. In the case of real-time requirements, various promising model predictive control approaches have been proposed, using either fast online solvers or offline-online decomposition. We also briefly comment on dimension reduction in many-objective optimization problems as another technique for reducing the numerical effort.

In this work, an embroidered textile moisture sensor is presented. The sensor is based on a capacitive interdigitated structure embroidered on a cotton substrate with an embroidery conductor yarn composed by 99% pure silver plated nylon yarn 140/17 dtex. In order to evaluate the sensor sensitivity, the impedance of the sensor has been measured by means of a LCR meter from 20 Hz to 20 kHz on a climatic chamber with a sweep of the relative humidity from 25% to 65% at 20 ºC. The experimental results show a clear and controllable dependence of the sensor impedance with the relative humidity. Moreover, the reproducibility of the sensor performance subject to the manufacturing process variability and washing process is also evaluated. The results show that the manufacturing variability introduce a moisture measurement error up to 4%. The washing process impact on the sensor behavior after applying the first washing cycle implies a sensitivity reduction higher than 14%. Despite these effect, the textile sensor keeps its functionality and can be reused in standard conditions. Therefore, these properties point out the usefulness of the proposed sensor to develop wearable applications on health and fitness scope including the user needs to have a life cycle longer than one-time use

This paper outlines the ongoing development of a specialised mobile application to address the mental health needs of vulnerable populations in the European Union (EU). Conducted as a mixed-methods research within two EU Science and Technology Cooperation Actions, the study prioritises stakeholder feedback to identify features for initial testing and strategies to improve application uptake, using critical digital health analysis. With a focus on marginalised groups such as refugees, migrants and socio-economically disadvantaged individuals, the application aims to provide an accessible and culturally sensitive platform for mental health support, integrating evidence-based interventions such as cognitive behavioural techniques and mindfulness exercises. Key features include multilingual support, habit tracking, personalised recommendations for support and services, and real-time crisis intervention. Collaboration with stakeholders and ongoing rigorous usability testing are driving the refinement process to ensure usability, acceptability and effectiveness, underscoring the importance of user engagement in technology-based mental health interventions in the EU context and highlighting the importance of collaborative science and technology for societal benefit.

Recently Palle has investigated the chiral vorticity and Cartan torsion in neutrino asymmetries. In his case he addressed this problem in Goedel s like anisotropic Einstein-Catan cosmology. In this paper we discusse how these ideas applied to sheared Bianchi types I Einstein-Cartan (EC) neutrino amisotropic cosmology, affect the handness of neutrinos in the universe. Actually here a novel concept of the chiral metric is introduced where metric functions also possess two distinct signs as in neutrino flipping or helicity. The axial anomaly equation for neutrinos in the presence of torsion and metric chirality is shown to produce left-handed neutrinos from right-handed torsion. Metric chirality is shown to be able to define how the metric would behave far away of neutrino density. Chiral flipping of the chiral neutrinos in the presence of torsion is also investigated. It is shown that when the chiral torsion is left-handed the chemical chiral potential vanishes as the universe expands.

Urban transit planning is going through a transition to greater private investment in many parts of the world and is now on the agenda in Australia. After showing examples of private investment in transit globally the paper focuses on historical case studies of private rail investment in Western Australia. These case studies mirror the historical experience in rapidly growing railway cities in Europe, North America and Asia (particularly Japan), and also the land grant railways that facilitated settlement in North America. The Western Australian experience is noteworthy for the small but rapidly growing populations of the settlements involved, suggesting that growth, rather than size, is the key to successfully raising funding for railways through land development. The paper shows through the history of transport, with particular reference to Perth, that the practice of private infrastructure provision can provide lessons for how to enable this again. It suggests that new partnerships with private transport investment as set out in the Federal Government City Deal process, should create many more opportunities to improve the future of cities through once again integrating transit, land development and private finance.

Innovative teaching strategies are designing a new and promising landscape in education. They fill up the lessons with creativity and imagination either for the students and teachers. This article addresses an attempt to make easier the approach to science in a non-scientific environment: primary education at university level. Gamification methodologies were combined with flipped classroom in order to free up in-class time and engage the students with the taught courses. A qualitative study was merged with quantitative measures of emotional and motivational parameters. These results were improved with four semi-structured interviews. The results clearly showed a raise in the students' motivational level, an acknowledgment of good teaching practice and an evident enhancement of felt positive emotions toward science teaching and scientific issues.

This work addresses the challenge of EEG visual multiclass classification into 40 classes for Brain-Computer interface applications, by using deep learning architectures. The visual multiclass classification approach offers BCI applications a significant advantage, since it allows the supervision of more than one BCI interaction, considering that each class label supervises a BCI task. However, because of the nonlinearity and nonstationarity of EEG signals, performing multiclassifiers based on EEG features remains a significant challenge for BCI systems. In the present work, mutual information-based discriminant channel selection and Minimum-Norm Estimate algorithms are implemented to select discriminant channels and enhance EEG data. Hence, deep EEGNet and Convolutional-recurrent neural networks are implemented separately to classify EEG data of image visualization into 40 labels. By using the k-fold cross-validation approach, average classification accuracies of 94.8% and 89.8% were obtained by implementing the aforementioned network architectures, respectively. Satisfactory results obtained with this method offer a new implementation opportunity for multi-task BCI applications by utilizing a reduced number of channels (<50%), compared to those presented in the related literature where the whole set of channels is used.

The consumption of sweet beverages, including sugar-sweetened beverages (SSB), artificially sweetened beverages (ASB) and fruit juices (FJ) is associated with the risk of different cardiometabolic diseases and probably with some tumors as well. We carried out a systematic review and meta-analysis of observational studies aimed at evaluating the association between sweet beverage intake and different types of cancer risk. Suitable papers published up to June 2020 were searched through PubMed, Web of Science and SCOPUS databases, using relevant keywords. Overall, 64 studies were identified for the systematic review, of which 27 were selected for the meta-analysis. This was performed by analyzing the multivariable-adjusted OR, RR or HR of the highest compared with the lowest sweet beverage intake categories. Random effects showed significant positive association between SSBs intake and breast (RR: 1.14, 95% CI: 1.01 – 1.30) and prostate cancer risk (RR: 1.18, 95% CI: 1.10 – 1.27), also between FJs and prostate cancer risk (RR: 1.03, 95% CI: 1.01 – 1.05). Associations between SSBs and colorectal and pancreatic cancer risk, FJs and breast, colorectal and pancreatic cancer risk, ASBs and pancreatic cancer risk tended to be positive but did not reach the statistically significant threshold. This study supports the recommendation to limit the consumption of SSBs and FJs for cancer prevention and proposes to further investigate the potential harmful role of ASBs intake in cancer risk.

An accurate, economical, and reliable device for detecting falls in persons ambulating with the assistance of an orthopedic walker is crucially important for the elderly and patients with limited mobility. Existing wearable devices such as wristbands are not designed for walker users, and patients may not wear them at all times. This research proposes a novel idea of attaching an internet-of-things (IoT) device with an inertial measurement unit (IMU) sensor directly to an orthopedic walker to perform real-time fall detection as well as activity logging. A dataset is collected and labeled for walker users in four activities, including idle, motion, step, and fall. Classic machine learning algorithms are evaluated using the dataset by comparing their classification performance. Deep learning with convolutional neural network (CNN) is also explored. Furthermore, the hardware prototype is designed by integrating a low-power microcontroller for onboard machine learning, an IMU sensor, a rechargeable battery, and Bluetooth wireless connectivity. The research results show the promise of improved safety and well-being of walker users.

The sheer number of gene variants and the extent of the observed clinical and molecular heterogeneity recorded in neuropsychiatric disorders (NPDs), could be due to the magnified downstream effects initiated by a smaller group of genomic higher order alterations in response to endogenous or environmental stress. Chromosomal common fragile sites (CFS) are functionally linked with microRNA’s, gene copy number variants (CNVs), sub-microscopic deletions and duplications of DNA, rare single-nucleotide variants (SNVs/SNPs) and small insertions/deletions (indels), as well as chromosomal translocations, gene duplications, altered methylation, microRNA and L1 transposon activity and 3-D chromosomal topology characteristics. These genomic structural features have been linked with various NPDs in mostly isolated reports, and have usually only been viewed as areas harboring potential candidate genes of interest. The suggestion to use a higher level entry point, (the ‘fragilome’ and associated features), activated by a central mechanism (‘stress’) for studying NPD genetics, has the potential to unify the existing vast number of different observations in this field. This approach may explain the continuum of gene findings distributed between affected and unaffected individuals, the clustering of NPD phenotypes and overlapping comorbidities, the extensive clinical and molecular heterogeneity and the association with certain other medical disorders.

In this work, two embroidered textile moisture sensors are characterized with three different conductive yarns. The sensors are based on a capacitive interdigitated structure embroidered on a cotton substrate with an embroidered conductor yarn. The performance comparison of 3 different type of conductive yarns has been addressed. In order to evaluate the sensor sensitivity, the impedance of the sensor has been measured by means of a LCR meter from 20 Hz to 20 kHz on a climatic chamber with a sweep of the relative humidity from 30% to 65% at 20 ºC. The experimental results show a clear and controllable dependence of the sensor impedance with the relative humidity and the used conductor yarns. This dependence points out the optimum conductive yarn to be used to develop wearable applications for moisture measurement.

The Signal Transducer and Activator of Transcription (STAT)3 and 5 are activated by many cytokine receptors to regulate specific gene expression and mitochondrial functions. Their role in cancer is largely context dependent as they can both act as oncogenes and tumor suppressors. We review here the role of STAT3/5 activation in solid cancers and summarize their association to survival in cancer patients. The molecular mechanisms that underpins the oncogenic activity of STAT3/5 signaling includes the regulation of genes that control cell cycle, cell death, inflammation and stemness. In addition, STAT3 mitochondrial functions are required for transformation. On the other hand, several tumor suppressor pathways act on or are activated by STAT3/5 signaling including the p19ARF/p53 pathway, tyrosine phosphatases, suppressor of cytokine signaling 1 and 3, the sumo ligase PIAS3, the E3 ubiquitin ligase TMF/ARA160 and the miRNAs miR-124 and miR-1181. Cancer mutations and epigenetic alterations may alter the balance between pro-oncogenic and tumor suppressor activities associated to STAT3/5 signaling explaining their context dependent association to tumor progression both in human cancers and animal models.

The application of the sensors optical fiber in the areas of scientific instrumentation and industrial instrumentation is very attractive due to its numerous advantages. In the industry of civil engineering for example, quasi-distributed sensors made with optical fiber are used for reliable strain and temperature measurements. Here, a quasi-distributed sensor in the frequency domain is discussed. The sensor consists of a series of low-finesse Fabry-Perot interferometers where each Fabry-Perot interferometer acts as a local sensor. Fabry-Perot interferometers are formed by pairs of identical low reflective Bragg gratings imprinted in a single mode fiber. All interferometer sensors have different cavity length, provoking the frequency-domain multiplexing. The optical signal represents the superposition of all interference patterns which can be decomposed using the Fourier transform. The frequency spectrum is analyzed and sensor´s properties were defined. Following, a quasi-distributed sensor was numerically simulated. Our sensor simulation considers sensor properties, signal processing, noise system and instrumentation. The numerical results show the behavior of resolution vs. signal-to-noise ratio. From our results, the Fabry-Perot sensor has high resolution and low resolutions. Both resolutions are conceivable because the FDPA algorithm elaborates two evaluations of Bragg wavelength shift

Tomato brown rugose fruit virus (ToBRFV) is a causal agent of severe emergent diseases in Solanaceae hosts with agronomic relevance, such as tomato and pepper. Herein, we analyzed the seed transmission rate and efficacy of different seed disinfection treatments and performed a comparison of molecular biology techniques seeking rapid and sensitive detection in seed lots. We evaluated several total RNA extraction and RT-PCR protocols using a distinct combination of PCR primers to test for the presence of the ToBRFV Mexican strain in tobacco host. Our results showed that the percentage of seed and seedlings transmission was less than 1% and that a 3% sodium hypochlorite solution was effective as a seed disinfection treatment. Finally, the most sensitive molecular method identified for virus detection consisted of a CTAB-Trizol RNA extraction followed by nested PCR using primers reported by Dovas et al. (2004). Additionally, we tested potential natural hosts in selected Cucurbitaceae and Solanaceae species. Our results showed that the ToBRFV Mexican strain is capable of experimentally infecting eggplant (Solanum melongena), tomatillo (Physalis ixocarpa), and tobacco (Nicotiana rustica).

Millimeter wave antennas have significance for high-speed, high-capacity wireless communication, delivering substantial advantages and an array of applications. This literature review analyzes the historical development, assessment of performance, difficulties with design, and contemporary applications in telecommunications, radar systems, and imaging. It covers the development of technology, especially within the context of 5G and beyond, and focuses at several antenna designs that deal with technical issues including reduction and impedance matching. The review also studies the effect of design on efficiency and bandwidth, identifying research gaps and potential futures, notably in terms of 5G technology. The commitment to develop millimeter wave antenna technology for next-generation wireless networks is evident, underlining the need of continued research and development.

The Autopoiesis and Cognition Theory (ACT), by Maturana and Varela, based on the notions of Biological Closure and Structural Coupling, is a well-known theory on how to understand biological organization [1, 2, 3]. Although, for example, the Free Energy Principle framework evokes some entailments of autopoiesis in a more formal setting [4, 5]; and ACT has been used in many fields, its impact has been restricted because it lacks quantitative analysis. Here we present a theoretical framework grounded in accepted and well-developed ideas from Mathematics and Physics which advance the understanding of the Principles of Biological Organization under the guidance of Biological Closure and Structural Coupling. The disciplines of Differential Geometry/Topology, Mechanics and Complex Dynamical Systems provide a powerful, elegant, and well-established body of knowledge to support our Biological Organization Principles (BOP) framework. In particular, Stochastic Mechanics and KAM theory (from Kolmogorov, Arnold and Moser theorem) allow us to develop, using the notions of Biological Closure and Structural Coupling, a central core of BOP termed Dynamical Closure Mechanism. Under the proposed framework, a wide variety of bio- logical phenomena can be understood, shedding new light on biological explanations. However, an understanding of biological organization may require the re-evaluation of dogmas on how we think on biology as it seems inescapable that what is needed is an integration of analysis and notions derived from mathematics, physics, and biology to generate a new landscape of ideas.

Fractional calculus gained a lot of attention in the last couple of years. Researchers discovered that processes in various fields follow rather fractional dynamics than ordinary integer-ordered dynamics, meaning the corresponding differential equations feature non-integer valued derivatives. There are several arguments for why this is the case, one of them being that fractional derivatives’ inherit spatiotemporal memory and/or the ability to express complex naturally occurring phenomena. Another popular topic nowadays is machine learning, i.e., learning behavior and patterns from historical data. In our ever-changing world with ever-increasing amounts of data, machine learning is a powerful tool for data analysis, problem-solving, modeling, and prediction. It further provides many insights and discoveries in various scientific disciplines. As these two modern-day topics provide a lot of potential for combined approaches to describe complex dynamics, this article reviews combined approaches of fractional derivatives and machine learning from the past, puts them into context, and thus provides a list of possible combined approaches and the corresponding techniques. Note, however, that this article does not deal with neural networks, as there already is profound literature on neural networks and fractional calculus. We sorted past combined approaches from the literature into three categories, i.e., preprocessing, machine learning & fractional dynamics, and optimization. The contributions of fractional derivatives to machine learning are manifold as they provide powerful preprocessing and feature augmentation techniques, can improve physically informed machine learning, and are capable of improving hyperparameter optimization. Thus, this article serves to motivate researchers dealing with data-based problems, to be specific machine learning practitioners, to adopt new tools and enhance their existing approaches.

The search for new food products that promote consumers health has always been of great interest. The dairy industry is perhaps the best example regarding the emergence of new products with claimed health benefits. Cheese whey (CW), the by-product resulting from cheese production, and second cheese whey (SCW), which is the by-product of whey cheese manufacture, have proven to be potential ingredients for the development of food products with improved nutritional characteristics and other functionalities. Nowadays, due to their nutritional quality, whey products have gained a prominent position among healthy food products. However, for long, CW and SCW were usually treated as waste or as animal feed. Due to their high organic content, these by-products can cause serious environmental problems if discarded without appropriate treatment. Small and medium size dairy companies do not have equipment and structure to process whey and second cheese whey. In these cases, generally, they are used for animal feed or discarded without an appropriate treatment, being the cause of several constraints. There are several studies regarding CW valorization and there is a wide range of whey products in the market. However, in the case of SCW remains a lack of studies regarding its nutritional and functional properties, as well as ways to reuse this by-product in order to create economic value and reduce environmental impacts associated to its disposal.

Radical reactions in water or aqueous media are important for organic synthesis, realizing high yielding processes under non-toxic and environmentally friendly conditions. This overview includes (i) a general introduction to organic chemistry in water and aqueous media, (ii) synthetic approaches in-, on- and with-water as well as in heterogeneous phase, (iii) reaction of carbon-centered radicals with water (or deuterium oxide) activated through coordination with various Lewis acids, (iv) photocatalysis in water and aqueous media, and (v) synthetic applications bioinspired from naturally occurring processes. A wide range of chemical processes and synthetic strategies under different experimental conditions have been reviewed that lead to important functional group translocation and transformation reactions, leading to the preparation of complex molecules. These results reveal how water as a solvent/medium/reagent in radical chemistry has matured over the last two decades and how further discoveries are foreseen to come in the near future.

The protection of electronics against environmental influences and mechanical loads is important for integration of conventional electronics in textile conductive tapes. For this purpose, the sensors on the tapes are molded with plastic locally. This process step is recognized in the injection molding process. The molding compound is then later selected depending on: The field of application, the parameters of the manufacturing process and the textile tape properties. We have designed a mould for liquid silicone (LSR) as well as for the textile and electronic insertions. The cavities are sealed by a local compression of the textile and the two inserts are positioned with position pins representing the main aspect of the mould design. The sampling tool and the process parameter optimization are mainly based on the material properties of the silicone and the mechanical sensitivity of the inserts. To reduce the deformation of the circuit boards by the melt front and ensuring the functionality of the electronics a low-pressure process is used.

Electrical transmission between neurons is largely mediated by gap junctions. These junctions allow the direct flow of electric current between neurons, and in mammals are mostly composed of the protein connexin (Cx)36. Circuits of electrically coupled neurons are widespread in these animals, plus, experimental and theoretical evidence supports the notion that, beyond synchronicity, these circuits are able to perform sophisticated operations like lateral excitation and inhibition, noise reduction, as well as the ability to selectively respond upon coincident excitatory inputs. Although once considered stereotyped and unmodifiable, we now know that electrical synapses are subject to modulation and, by reconfiguring neural circuits, these modulations can alter relevant operations. The strength of electrical synapses depends on gap junction conductance, as well as on its functional interaction with the electrophysiological properties of coupled neurons. In particular, voltage dependent channels of the non-synaptic membrane critically determine the efficacy of transmission at these contacts. Consistently, modulatory actions on these channels have been shown to represent relevant mechanisms of plasticity of electrical synaptic transmission. Here we review recent evidence on the regulation of electrical synapses of mammals, the underlying molecular mechanisms, and the possible ways in which they affect circuit function.

Time recordings of impulse-type oscillation responses are short and highly transient. These characteristics may complicate the usage of classical spectral signal processing techniques for a) describing the dynamics and b) deriving discriminative features from the data. However, common model identification and validation techniques mostly rely on steady-state recordings, characteristic spectral properties and non-transient behavior. In this work, a recent method, which allows reconstructing differential equations from time series data, is extended for higher degrees of automation. With special focus on short and strongly damped oscillations, an optimization procedure is proposed that fine-tunes the reconstructed dynamical models with respect to model simplicity and error reduction. This framework is analyzed with particular focus on the amount of information available to the reconstruction, noise contamination and non-linearities contained in the time series input. Using the example of a mechanical oscillator, we illustrate how the optimized reconstruction method can be used to identify a suitable model and to extract features from uni-variate and multivariate time series recordings in an engineering-compliant environment. Moreover, the determined minimal models allow for identifying the qualitative nature of the underlying dynamical systems as well as testing for the degree and strength of non-linearity. The reconstructed differential equations would then be potentially available for classical numerical studies, such as bifurcation analysis. These results represent a physically interpretable enhancement of data-driven modeling approaches in structural dynamics.

Sword-duels are interesting, from a game-theoretical perspective, as they correspond to sudden-death interactions between players (i.e., defeat means removal from the game), and where victory/defeat depend on not just skill, but also luck. Analyzing probabilities of victory streaks, given a certain level of self and others' skill, is thus relevant for any application domain that can be modeled in the same way. This paper takes inspiration from Miyamoto Musashi, famously undefeated for 61 duels, and implements a Markov-chain Monte-Carlo simulation approach to evaluate this scenario. Results suggest that a 61 victory streak can be probabilistically observed when skill level is roughly 6.5 times that of the average duelist, and with 95\% confidence when skill level is roughly 1000 times that of the average duelist. More generally, this paper provides a method for determining chances of victory streaks in game-theoretical sudden-death encounters, when both "skill" and "luck" contribute to the outcome of the encounter. Specific scenarios can be modeled by modifying the utilized Markov chain and adjusting sampled distributions as required.

The present distribution examines the effects of nozzle diameter, inlet mass rate, and channel geometry on the fuel distribution in annular combustion chambers of micro gas turbines, taking into account the importance of more uniform fuel distribution in the nozzles connected to the fuel supply channels. A comparison has been made between the numerically calculated pressure drop between the inlet and outlet of the fuel supply nozzle and the experimental value obtained. All fuel supply nozzles with a diameter of 500 micrometers are considered for the micro gas turbine. A more uniform distribution results in better combustion and higher efficiency. A geometrical change in the design of the fuel supply nozzle improved the uniformity of the flow distribution without increasing the pressure drop.

An inducer is one of the most important components of centrifugal pumps, whose presence will result in a significant increase in hydraulic performance and pump efficiency. The primary function of the inducer, however, is to delay the destructive phenomenon of cavitation, which has presented a considerable design challenge. Nevertheless, the amount of improvement and increase in inducer performance in both cavitation and non-cavitation modes depends critically on the radial laxity of the blade tip. As part of this study, the performance of the inducer in the cavitation state has been simulated and compared with the experimental data, which are in good agreement. This paper examines the effect of blade tip lagging on cavitation, and the results indicate that this will improve cavitation ­and delay this destructive phenomenon ­but will negatively affect the non-cavitation performance. With the increase in clearance, the range of the return current will increase at the tip of the inducer blade as well.

Methods for cost calculation of Laser-based Additive Manufacturing (LAM) have evolved over the last two decades. Starting from a rapid prototyping manufacturing method, cost calculation over time included more than single part production for small series or mixed batches. New machine developments nowadays aim at large scale production and introduce modular machine designs that give LAM factory operators more decision freedom on machine configurations and expansibility. To leverage this new possibilities, LAM costing methods must be adapted to calculate and visualize the economic consequences of different module configurations.In this work a modelling architecture of L-PBF machines using virtual modules is presented. Using principles of the industry 4.0 communication standard OPC UA, a virtual machine is set up, parametrized and connected to the AM digital process chain. Two different views on the cost information are used, optimized for different use cases.First, the product view allows detailed analysis of cost allocation to parts in mixed batches and the layered geometry of the part. Second, the machine view tracks utilization of all machine modules, divided into the states idle, active, off and maintenance. The theoretical Overall Equipment Effectiveness (OEE) is calculated on a module basis, enabling economic analysis and optimization of module composition as well as module improvements and new modular machine constellations. This allows focusing research and development on most valuable improvements. By calculating different scenarios like spare part production, mass production or rapid prototyping, the part portfolio to be manufactured can be considered.

The need for Artificial Intelligence (AI) and Machine Learning (ML) technologies is increasingly being leveraged for optimizing Data centers’ (DCs’) operations as the volume of operations management data increase tremendously. These strategies can assist operators in better understanding their DC operations and making informed decisions up front to preserve service reliability and availability. Aiming at creating models that optimize energy efficiency, identify inefficient resource utilization and scheduling policies, and predict outages. Apart from model hyperparameter tuning, feature selection is a crucial step to identify relevant features with the objective of providing insight into the data, improving performance, and reducing computational expenses. Although several feature selection methods have been discussed in various domains, none have been discussed in the context of the data center. This paper introduces SHapley Additive exPlanation (SHAP), a class of additive feature attribution values-based feature selection that is rarely discussed in literature. We compared the effectiveness of SHAP method with several widely used methods. We used a real DC dataset obtained from the ENEA CRESCO6 cluster with 2,0832 cores to evaluate the methods. To demonstrate the comparison of the methods, we picked the top 10 most important features from each method, the predictions were retrained, and their performance was evaluated using MAE, RMSE, and MPAE. The results show that the SHAP-assisted feature selection performed best and align with human intuition.

Although CAD/CAM ceramics present a promising alternative to metal-ceramic fixed dental prostheses, little is known about their mid- and long-term clinical performance. This systematic review aims to estimate the survival and success rates and describes the underlying complication characteristics for CAD/CAM tooth-supported fixed dental prostheses (FDPs). We systematically searched MEDLINE and Web of Science to find relevant prospective studies with a follow-up of at least one year. We estimated pooled 1-, 5- and 10-year survival and success rates by combining the collected data in a Poisson regression model. Descriptive statistics were conducted to evaluate the distribution of failures and complications in the included studies. Risk of bias for the included studies was assessed with an adapted checklist for single-arm trials. Pooled estimated 1-, 5-, and 10-year survival rates ranged from 93.80% to 94.66%, 89.67% to 91.1%, and 79.33% to 82.20%, respectively. The corresponding success rates, excluding failures but including any other types of intervention, were 94.53% to 96.77%, 90.89% to 94.62%, and 81.78% to 89.25%. Secondary caries was the most frequent cause of failure, followed by chipping of the veneering. The most common cause of complication, excluding failures but requiring intervention, was chipping of the veneering. Risk of bias was generally acceptable for the included studies, with 7 studies associated with low risk of bias, 8 studies with a moderate risk of bias, and 3 studies with serious risk of bias. The current meta-analysis on CAD/CAM supported FDPs revealed satisfying survival and success rates for up to 10 years of exposure. More prospective studies focusing on long-term performance are needed to strengthen the evidence currently available in the literature.

The use of isolated supplements to enhance performance is widespread among athletes. The aim of this study was to increase knowledge about the combined effects of caffeine and New Zealand blackcurrant (NZBC) dietary supplements. In this study, two subjects each underwent four phases of four sessions in a double-blind and randomized alternating treatment single-case design. After a 3-week pre-test phase, the supplement combinations of placebo/placebo, caffeine/placebo (5 mg/kg), NZBC/placebo (600 mg), and caffeine/NZBC (5 mg/kg + 600 mg) were taken and weekly performance tests were conducted to examine their effects on relative power (W/kg) during a 20-minute time trial on a bicycle. Data were analyzed descriptively and using the Tau-U calculator from Single Case Research. The ergogenic effect of caffeine was confirmed in both subjects, with increases of 3.3% and 6.5%, while the positive effect of NZBC on performance was only seen in one subject (13.4%). The combination of caffeine and NZBC again increased performance in both subjects (2.2% and 19.2%), but the data only showed an additive effect of the supplements in one subject. Further studies are required to confirm or refute this evidence of the synergistic effects of these supplements.

The paper combines two new original concepts about eco-energetic systems. The first one is related to the M.E.N. (Mega-Eco-Nega-Watt) paradigm, which is based on three different but complementary ecological economic spaces: MEGAWATT, as needed energy, ECOWATT, as ecological energy, and NEGAWATT, as preserved energy, even the renewable energies and technologies, in the context of electrical energy production. The second concept presented in this paper is the eco-energetic efficiency, introduced in order to facilitate a correlation between the energetic efficiency of the system and a necessary, new defined ecological coefficient. The proposed formula for eco-energetic efficiency enables an interesting form of reporting to the different situations in which the input energy, output energy, lost energy and externalities, involved in an energetic process interact to produce energy in a specific energetic system, in connection with the circular economy model. Finally, is presented an original diagram of the energetic chains to produce electricity in a resilience regim, with high eco-energetic efficiency from originating in different primary energetic sources as external (gravitation & solar sources), fuels (classical & radioactive), internal sources and others. Even what kind of energetic sources are used to obtain electricity, as coals, gas, wood, hydropower, nuclear power, wind power, biomass, solar systems, and others, the entire process should be sustainable in what is the transdisciplinary integration of the different representative spheres as energy, socio-economy, ecology (environment), with the main core, sustainable education, inclueding the law and administrative aspects, as necessary fields of the knowledge based society/economy.

Probabilistic latent semantic analysis is a statistical technique developed for information retrieval and spanned many fields. It yields intuitive and solid results. However, the rigidity of the assumptions and the iterative nature derived from the Expectation-maximization algorithm generate several problems, dividing detractors and enthusiasts. In this manuscript, we first describe the Probabilistic latent semantic analysis. After, we discuss reformulations that attempt to solve these problems. We pay special attention to the works relating Probabilistic latent semantic analysis and the Singular value decomposition Theorem. Also, Probabilistic latent semantic analysis can be the basis for other techniques, such as kernelization or probabilistic transfer learning, and those that extend the descriptive character of the Principal component analysis to an inferential tool and open a window of opportunities.

The present state of the natural environment is significantly influenced by the construction sector. Due to the large amounts of consumed natural resources and materials as well as the high volume of emitted pollutants, the building industry is considered to have a key influence in achieving a global sustainable development. A considerable part of the ecological impact of the built environment is influenced by the energy consumed for creating appropriate indoor conditions as well as by the greenhouse gases that are emitted during the operation stage of a building’s life cycle. Therefore, the energy performances of existing buildings must be significantly improved in the near future. This paper analyzes the influence of the thermal insulation thickness of walls on the linear thermal transmittances and the heating demand of an existing building. The resulted values show that while increasing the insulation of the walls leads to a serious heat demand reduction, a deep renovation of the building cannot be achieved solely by using this solution.

Molecules sourced from marine environments hold immense promise for the development of novel therapeutic drugs, owing to their distinctive chemical compositions and valuable medicinal attributes. Notably, Talarolide A and Talaropeptides A-D have gained recent attention as potential candidates for pharmaceutical applications. This study aims to explore the chemical reactivity of Talarolide A and Talaropeptides A-D through the application of molecular modeling and computational chemistry techniques, specifically employing Conceptual Density Functional Theory (CDFT). By investigating their chemical behaviors, the study seeks to contribute to the understanding of the potential pharmacological uses of these marine-derived compounds. The investigation involves the utilization of molecular modeling and computational chemistry tools, with a specific focus on Conceptual DFT. These techniques are applied to examine the chemical reactivity of Talarolide A and Talaropeptides A-D, shedding light on their potential for interacting with various biological targets. The research reveals insights into the chemical reactivity of Talarolide A and Talaropeptides A-D, uncovering active reaction sites and potential biological targets. Talarolide A demonstrates robust anti-inflammatory properties and antitumor activity against diverse cancer cell lines, while Talaropeptide A displays antimicrobial efficacy against both bacteria and fungi. The study underscores the significance of comprehending the chemical reactivity of natural marine products for advancing pharmaceutical development. By employing computational tools such as Conceptual DFT, this research uncovers crucial information about the active sites and potential targets of Talarolide A and Talaropeptides A-D. The findings contribute to the broader understanding of marine-derived peptides and their prospects as pharmaceutical agents, though further investigations are necessary to fully elucidate their pharmacological attributes.

In the field of robotics education, introductory courses would ideally utilize heavy industrial arms for hands-on learning. This would provide students with valuable experience in joint programming, which involves direct control of each joint motor in the arm to accomplish desired path planning and differential movements. This practice requires consideration of the physical dynamics of the arm. However, the use of heavy industrial arms has several drawbacks. They are large and expensive, require specialized maintenance, can pose safety risks, and they typically do not allow for direct control of the joint motors. One solution is to use a small, lightweight, toy-like arm. While these are cost-effective and provide direct access to the joint motors without posing safety risks, their lightweight construction means they exhibit minimal dynamic behavior, which limits their educational value. Another solution involves a robotic arm simulator that uses a virtual arm. However, a virtual arm doesn't offer the same level of hands-on engagement and excitement as a physical arm. We propose a hybrid solution that combines a small physical arm with a virtual arm. This approach provides students with the experience of working with an industrial arm, but without the associated difficulties. We demonstrate how this approach successfully improved the completion rate of joint programming assignments, offering a promising solution for practical robotics education.

Proteins and DNA exhibit key physical chemical properties that make them advantageous for building nanostructures with outstanding features. Both DNA and protein nanotechnology have growth notably and proved to be fertile disciplines. The combination of both types of nanotechnologies is helpful to overcome the individual weaknesses and limitations of each one, paving the way for the continuing diversification of the structural nanotechnologies. Recent studies have implemented a synergistic combination of both biomolecules to assemble unique and sophisticate protein-DNA nanostructures. These hybrid nanostructures are highly programmable and display remarkable features that create new opportunities to build in the nanoscale. This review focuses on the strategies deployed to create hybrid protein-DNA nanostructures. Here, we will discuss strategies such as polymerization, spatial directing and organizing, coating, rigidizing or folding DNA into particular shapes or moving parts. The enrichment of structural DNA nanotechnology by incorporating protein nanotechnology has been clearly demonstrated and still shows a large potential to create useful and advanced materials with cell-like properties or dynamic systems. It can be expected that structural protein-DNA nanotechnology will open new avenues in the fabrication of nano-assemblies with unique functional applications and enrich the toolbox of bionanotechnology.

Over the past few decades, phototherapy, encompassing the utilization of both natural and artificial light, has emerged as a dependable and non-invasive strategy for addressing a diverse range of illnesses, diseases, and infections. This therapeutic approach, primarily known for its efficacy in treating skin infections such as herpes and acne lesions, involves the synergistic use of specific light wavelengths and photosensitizers like methylene blue. Photodynamic therapy, as it is termed, relies on the generation of antimicrobial reactive oxygen species (ROS) through the interaction between light and externally applied photosensitizers. Recent research, however, has highlighted the intrinsic antimicrobial properties of light itself, marking a paradigm shift in focus from exogenous agents to the inherent photosensitivity of molecules found naturally within pathogens. Chemical analyses have identified specific organic molecular structures and systems, including porphyrins and conjugated C=C bonds, as pivotal components in molecular photosensitivity. Given the prevalence of these systems in organic life forms, there is an urgent need to investigate the potential impact of phototherapy on individual molecules expressed within pathogens and discern their contributions to the antimicrobial effects of light. This review delves into the recently unveiled key molecular targets of phototherapy, offering insights into their potential downstream implications and therapeutic applications. By shedding light on these fundamental molecular mechanisms, we aim to advance our understanding of phototherapy's broader therapeutic potential and contribute to the development of innovative treatments for a wide array of microbial infections and diseases.

In this article, we investigate the applicability of quantum machine learning for classification tasks using two quantum classifiers from the Qiskit Python environment: the Variational Quantum Classifier (VQC) and the Quantum Kernel Estimator (QKE). We evaluate the performance of these classifiers on six widely known and publicly available benchmark datasets and analyze how their performance varies with the number of samples on two artificially generated test classification datasets. As quantum machine learning is based on unitary transformations, this paper explores data structures and application fields that could be particularly suitable for quantum advantages. Hereby, we developed a data set based on concepts from quantum mechanics using the exponential map of a Lie algebra. This dataset will be made publicly available and contributes a novel contribution to the empirical evaluation of quantum supremacy. We further compared the performance of VQC and QKE on six widely applicable datasets to contextualize our results.\\ Our results demonstrate that the VQC and QKE perform better than basic machine learning algorithms such as advanced linear regression models (Ridge and Lasso). They do not match the accuracy and runtime performance of sophisticated modern boosting classifiers like XGBoost, LightGBM, or CatBoost. Therefore, we conclude that while quantum machine learning algorithms have the potential to surpass classical machine learning methods in the future, especially when physical quantum infrastructure becomes widely available, they currently lag behind classical approaches. Our investigations also show that classical machine learning approaches have superior performance classifying datasets based on group structures, compared to quantum approaches that particularly use unitary processes.\\ Furthermore, our findings highlight the significant impact of different quantum simulators, feature maps, and quantum circuits on the performance of the employed quantum estimators. This observation emphasizes the need for researchers to provide detailed explanations of their hyperparameter choices for quantum machine learning algorithms, as this aspect is currently overlooked in many studies within the field.\\ To facilitate further research in this area and ensure the transparency of our study, we have made the complete code available in a linked GitHub repository.

Summer annual species are the most widely grown crops in the Upper Midwest, but reliance on a summer annual system has led to excessive soil and nutrient loss when crops are not present. Integrating winter rye (Secale cereale L.), known for its hardiness and environmental benefits, into the rotation can address these issues. However, there's limited understanding of the phenotypic diversity in winter rye during key growth stages that overlap with the typical planting dates for corn (Zea mays L.), soybean [Glycine max (L.) Merr], and late-planted crops like dry bean (Phaseolus vulgaris L.). Thus, the objectives of this study were to evaluate changes in biomass accumulation and quality of winter rye and triticale (x Triticosecale Wittmack) cultivars at three growth stages. Twenty cultivars were assessed over the 2014-2015 and 2015-2016 growing seasons across three environments in Minnesota. Winter rye and triticale were harvested for biomass at the tillering, booting, and soft dough growth stages and rye biomass yield and quality [i.e., crude protein, neutral detergent fiber (NDF), and 48-hour digestibility (NDFD)] were determined following harvest. Overall, there was little variation in each parameter among the cultivars within a location and growth stage. NDFD had some variation at the soft dough stage where digestibility ranged from 273 to 324 g kg-1 at the Crookston site and 332 to 406 g kg-1 at the St. Paul site. The lack of difference between cultivars indicates a wide range of choice when selecting a winter rye cultivar.

Traditional flood hazard analyses often rely on univariate probability distributions; however, in many coastal catchments, flooding is the result of complex hydrodynamic interactions between multiple drivers. For example, synoptic meteorological conditions can produce considerable rainfall-runoff, while also generating wind-driven elevated sea levels. When these drivers interact in space and time, they can exacerbate flood impacts; this phenomenon is known as compound flooding. In this paper, we build a Bayesian Network based on Gaussian copulas to generate the equivalent of 500 years of daily stochastic boundary conditions for a coastal watershed in Southeast Texas. In doing so, we overcome many of the limitations of conventional univariate approaches and are able to probabilistically represent compound floods caused by riverine and coastal interactions. We calculate the resulting water levels using a 1D steady-state hydraulic model and find that flood stages in the catchment are strongly affected by backwater effects from tributary inflows and downstream water levels. By comparing with a bathtub modeling approach, we show that simplifying the multivariate dependence between flood drivers can lead to an underestimation of flood impacts, highlighting that accounting for multivariate dependence is critical for the accurate representation of flood risk in coastal catchments prone to compound events.

In the rapidly evolving landscape of genetic engineering, the advent of CRISPR-Cas technologies has catalyzed a paradigm shift, empowering scientists to manipulate the genetic code with unprece-dented accuracy and efficiency. Despite the remarkable capabilities inherent to CRISPR-Cas sys-tems, recent advancements have witnessed the integration of small molecule to augment their functionality, introducing new dimensions to the precision and versatility of gene editing applica-tions. This review delves into the synergy between CRISPR-Cas technologies and small molecule drugs, elucidating the pivotal role of chemicals in optimizing target specificity and editing efficiency. By examining a diverse array of applications, ranging from therapeutic interventions to agricultural advancements, we explore how the judicious use of chemicals enhances the precision of CRISPR-Cas-mediated genetic modifications. In this review we emphasize the significance of small molecule drugs in fine-tuning the CRISPR-Cas machinery, which allows researchers to exert meticulous con-trol over the editing process. We delve into the mechanisms through which these chemicals bolster target specificity, mitigate off-target effects, and contribute to the overall refinement of gene edit-ing outcomes. Additionally, we discuss the potential of chemical integration in expanding the scope of CRISPR-Cas technologies, enabling tailored solutions for diverse genetic manipulation challenges. As CRISPR-Cas technologies continue to evolve, the integration of small molecule drugs emerges as a crucial avenue for advancing the precision and applicability of gene editing techniques. This re-view not only synthesizes current knowledge but also highlights future prospects, paving the way for a deeper understanding of the synergistic interplay between CRISPR-Cas systems and chemical modulators in the pursuit of more controlled and efficient genetic modifications.

Accurate prediction of crop production is essential in effectively managing agricultural countries' food security and economic resilience. This study evaluates the performance of statistical and machine learning-based methods for large-scale crop production forecasting. We predict the quarterly production of 325 crops (including fruits, vegetables, cereals, non-food, and industrial crops) across 83 provinces in the Philippines. Using a comprehensive dataset of 10,949 time series over 13 years, we demonstrate that a global forecasting approach using a state-of-the-art deep learning architecture, the transformer, significantly outperforms traditional local forecasting approaches built on statistical and baseline methods. By leveraging cross-series information, our proposed way is scalable and works well even with time series that are short, sparse, intermittent, or exhibit structural breaks/regime shifts. The results of this study further advance the field of applied forecasting in agricultural production and provide a practical and effective decision-support tool for policymakers that oversee the farm sector on a national scale.

Addressing the increasing nursing demand in the face of a limited nursing workforce, understanding job satisfaction and retention becomes critical. Our cross-sectional study, conducted among 2,572 nurses in Bavaria, Germany, uncovers a dichotomy where nurses have strong empathy for their profession yet yearn for significant improvements. The top areas identified for enhancement include (i) ensuring sufficient time for patient care, (ii) providing a reliable service organization with minimal unplanned shift changes, and (iii) streamlining nursing documentation. Moreover, the largest disparity between expectations and job satisfaction was measured in patient care time. Multivariable regression analysis further investigates factors influencing intentions to stay in the profession, including (i) demographic aspects (age, living conditions), (ii) working area, (iii) working hours, (iv) career choice satisfaction, (v) career opportunities, (vi) payment, (vii) working and rest times, and (viii) satisfaction derived from aiding individuals in challenging life situations. The findings uncover a need to change nursing conditions, and measures for younger nurses and elderly care nursing. Although there are limitations, and a potential bias due to convenience sampling, our study provides key insights into nursing conditions. Future research should broaden its scope to investigate nurse job satisfaction and retention, emphasizing potential relief tools such as digitization.

The strong couplings among ecological, economic, social and technological processes explains the complexification of human-made systems, and phenomena such as globalization, climate change, the increased urbanization and inequality of human societies, the power of information, and the COVID-19 syndemics. Among complexification’s essential features are non-decomposability, asynchronous behavior, components with many degrees of freedom, increased likelihood of catastrophic events, irreversibility, nonlinear phase spaces with immense combinatorial sizes, and the impossibility of long-term, detailed prediction. Sustainability for complex systems implies enough efficiency to explore and exploit their dynamic phase spaces and enough flexibility to coevolve with their environments. This in turn means solving intractable nonlinear semi-structured dynamic multi-objective optimization problems, with conflicting, incommensurable, non-cooperative objectives and purposes, under dynamic uncertainty, restricted access to materials, energy and information, and a given time horizon, aiming at enhancing the co-evolutionary power of the Biosphere and its human subsystems. Giving the high-stakes, the need for effective, efficient, diverse solutions, their local-global, present-future effects, and their unforeseen short, medium and long-term impacts, achieving sustainable complex systems implies the need for Sustainability-designed Universal Intelligent Agents, harnessing the strong functional coupling between human, artificial and nonhuman biological intelligence in a no-zero-sum game to achieve sustainability.

Purpose To analyse diagnostic and therapeutic impact of molecular imaging TNM (miTNM) stage obtained with 18F-DCFPyL versus 18F-Fluorocholine in head to head comparison in biochemical recurrence (BCR) prostate cancer (PCa). Material and methods Patients with BCR PCa after radical treatment with previous 18F-Fluorocholine-PET/CT (negative or oligometastatic disease) were derived to 18F-DCFPyL-PET/CT. Patients were classified attending to: grade group, EAU classification, PSA, PSA doubling time (PSAdt) and PSA velocity (PSAvel). The overall detection rate (DR) and miTNM stage according to PROMISE criteria were assessed for both radiotracers and also correlation (Kappa). The influence of PSA and kinetics on both PET/CT (DR and miTNM) and predictive value of unfavourable kinetics on miTNM were determined. Cut-off PSA, PSAdt and PSAvel values able to predict PET/CT results were determined. Change in miTNM and treatment derived of 18F-DCFPyL information with respect to 18F-Fluorocholine was also evaluated. Results We studied 138 patients. 18F-DCFPyL showed a higher DR than 18F-Fluorocholine (64.5% vs 33.3%). 18F-DCFPyL and 18F-Fluorocholine detected T in 33.3% versus 19.6%, N in 27.5% versus 13.8%, M in 30.4% versus 8.7%. Both tracers DR showed significant associations with PSA and PSAvel. Significant association was only found between miTNM and PSA on 18F-Fluorocholine-PET/CT (p=0.033). For 18F-Fluorocholine and 18F-DCFPyL PET/CT a PSAdt cut-off of 4.09 and 5.59 months, respectively, were able to predict M stage. 18F-DCFPyL changed therapeutic management in 40/138 patients. Conclusion 18F-DCFPyL provides a higher DR and superior miTNM staging than 18F-Fluorocholine in restaging BCR, especially with high PSA and unfavourable PSA kinetics, showing a fair agreement to 18F-Fluorocholine.

In recent years the yield of fruits and vegetables have been decreasing in Colombia, threatening national food security. Analysis of crop production data may lead to identifying cropping systems that have shown better adaptability to changes in climatic and non-climatic factors associated with agricultural production. The open database AGRONET keeps data of the agricultural activities conducted in Colombia, allowing to find the information organized by crops, regions and years; each row of the database registers farm information in Colombia. Aiming to identify resilient crops systems, agricultural data of fruits and vegetables were analyzed. First, trends in crop production were studied by year and locations, detecting the regions and crops with highest yields in the period from 2006 until 2020. Then, mixed linear regression and principal components analysis were applied to elucidate the relation between non-climatic factors and crop yield. In Colombia, vegetable production was more efficient than fruits, observing yields of 10.23 and 13.33 t ha^-1, respectively. On the other hand, the Colombian central region showed high yields for vegetables, while for fruits this was exhibited in northern and eastern locations. In the present study, yield variation responded to changes in the location of crop systems, while years had no effect on vegetable production. Furthermore, the price of the agricultural product and the cost of fertilizers were associated with the yield of the analyzed crops systems. In Colombia, carrot, cabbage, tomato papaya and pineapple are resilient crops whose yield increases especially by the regions where they are cultivated.

Background: Although persistent systemic inflammation is considered to be predictive for future cardiovascular events, it remains unclear whether or not C-reactive protein (CrP) plays an active role in coronary-plaque instability. Here, we report a case of a patient with failed and super-infected renal allograft as a source for systemic inflammation presenting with repeat acute coronary syndromes. Case presentation: A 52-years-old male type-2 diabetic with a failed kidney transplant who was hospitalized for acute urinary-tract infection. In the presence of other, classic cardiovascular risk factors, peak values of CrP coincided with episodes of unstable angina treated by percutaneous coronary interventions. Besides pyelonephritis, the histological examination of the kidney transplant revealed signs of chronic rejection and the presence of a renal cell carcinoma in situ. Once the renal allograft has been removed, systemic inflammation was attenuated, the patient was not re-hospitalized for acute-coronary syndrome within the next 12 months. Conclusion: In this case, systemic inflammation was paralleled by instability of coronary plaques as documented by repeat percutaneous coronary interventions.

A nanostructured electrochemical bi-sensor system for analysis of milks has been developed using the Layer by Layer technique. The non-enzymatic sensor [CHI+IL/CuPcS]2, is a layered material containing a negative film of the anionic sulfonated copper phthalocyanine (CuPcS) acting as electrocatalytic material, and a cationic layer containing a mixture of an ionic liquid (IL) (1-butyl-3-methylimidazolium tetrafluoroborate) that enhances the conductivity and chitosan (CHI) that facilitates the enzyme immobilization. The biosensor ([CHI+IL/CuPcS]2-GAO) results from the immobilization of galactose oxidase on the top of the LbL layers. FTIR, UV-vis and AFM have confirmed the proposed structure and cyclic voltammetry has demonstrated the amplification caused by the combination of materials in the film. Sensors have been combined to form an electronic tongue for milk analysis. Principal Component Analysis has revealed the ability of the sensor system to discriminate between milk samples with different lactose content. Using PLS-1 calibration models, correlations have been found between the voltammetric signals and chemical parameters measured by classical methods. PLS-1 models provide excellent correlations with lactose content. Additional information about other components such as fats, proteins and acidity can also be obtained. The method developed is simple and the short response time permits its use in assaying milk samples on-line.

The research deals with the particularities of the initiation in the sport of kin ball, of 94 students (54 boys and 40 girls), without a history of practicing the sport intensively, and the measure of the influence of some components of the motor capacity. Kin ball is a sport that appeared in Canada, in an academic setting and can become an alternative sport in the common university curricula in Romania. The research was carried out in 4 research groups in 2019 and 2022, two of boys and two of girls, similarly, before and after the declaration of the acute phase of the Covid-19 Pandemic, generating physical activity constraints. The originality of the research refers to the initiation, unprecedented in Romania, in the Kin ball sport, through 20 training sessions, carried out in 10-day stages and the evaluation of some motor skills on the subjects. During the experiment, the following components were tested pre- and post-intervention Kin-Ball: palmar muscle strength using the dynamometer, general resistance by running as long as possible for 2 min and general coordination function - body balance, by the Matorin test. The statistical calculation included the application of the Kolmogorov-Smirnov test, depending on which parametric or non-parametric statistical significance tests were applied and the estimation of the size of the intervention effect. The results highlighted particularities of initiation in Kin ball, but also significant differences (p<0.05) in all measurements performed in 2022. The tests in 2019 recorded both significant and statistically insignificant differences, also highlighted by the calculation of the d indicator of to Cohen. The lower initial level of all motor components measured in 2022 and their significant improvement represent aspects that can be understood as collateral effects of the lack of movement during the pandemic.

Currently, the use of sustainable chemistry as an ecological alternative for the generation of products or processes, free of polluting substance has assumed a preponderant role. The aim of this work is propose a bioinspired, facile, at low cost, non-toxic and environmentally friendly alternative to obtaining magnetic nanoparticles whit a majority phase of magnetite (Fe₃O₄). Is important to empathize that the synthesis was based on the chemical reduction through the Cnicus Benedictus extract, whose use as reducing agent has not been reported in the synthesis of iron oxides nanoparticles. In addition, the Cnicus Benedictus is abundant endemic plant in Mexico, with several medicinal properties and a large number of natural antioxidants. The obtained nanoparticles exhibited significant magnetic and antibacterial properties and an enhanced photocatalytic activity. The crystallite size of the Fe₃O₄ nanoparticles (Fe₃O₄ NP’s) was calculated by Williamson-Hall method. The photocatalytic properties of the Fe₃O₄ NP´s were studied by kinetics absorptions models in the Congo red (CR) degradation. Finally the antibacterial effect of the Fe3O4 NP´s were evaluated mediated the Kirby-Bauer method against E. coli and S. aureus bacteria. This route offers a green alternative to obtain Fe3O4 NP´s with remarkable magnetic, photocatalytic and antibacterial properties.

The relative paucity of donor livers suitable for transplantation has sparked innovations to preserve and recondition organs to expand the pool of transplantable organs. Currently, machine perfusion techniques have led to the improvement of the quality of marginal livers and to prolonged cold ischemia time and allowed for the prediction of graft function through analysis of the organ during perfusion, improving the rate of organ use. In the future, the implementation of organ modulation might expand the scope of machine perfusion beyond its current usage. The aim of this review was to provide an overview of the current clinical use of machine perfusion devices in liver transplantation and provide a perspective for future clinical use, including therapeutic interventions in perfused donor liver grafts.

In the age of social media your personal branding is critical to find a job. Information is highly available and handy for everyone looking for a job as well as for people trying to recruit employees at all levels. Currently, there is a first e-impression that encompasses employee education, qualifications, and relationships. This e-impression is given by your social media, specifically those websites that were built to facilitate interactions between employee and employer during the job-hunting process. There are different websites that enable you to establish a social network. For example, meet, Xing, Bark, Opportunity, Lunchmeet, and LinkedIn among others. This article is written by a group of young undergraduate and graduate researchers, who have noticed the importance of social networks to apply for graduate school and industry jobs. This manuscript offers ten simple rules that include resources to facilitate the journey on LinkedIn-like social networks, hoping that you have a successful career description in the most popular professional social networking site.

In the marine environment, fish parasites are present in most species of seafood. The most com-mon is Anisakis spp. a nematode that can parasitize human tissues causing anisakiasis and al-lergies, in some cases with a strong reaction such as anaphylactic shock in sensitive people. This happens when people ingest live or dead larvae present in the muscles or viscera of a wide range of seafood, fish and cephalopods. Consumer education has been positioned as one of the most ef-fective alternatives for its prevention. This study sought to identify the species that present the greatest risk of anisakiasis for consumers taking into account sex, age and their knowledge about this parasitosis. The objective was to offer recommendations for better consumer information to-wards the prevention of infections by worm larvae. The results revealed that the species most at risk were hake and cod and that young participants know more about the risks of anisakiasis from raw seafood. The gaps detected in the knowledge about the ability of thermal treatments to eliminate parasites, especially in allergic people, must be addressed for better prevention, sug-gesting campaigns adapted by sectors of the population.

This study examines whether information about the winners of the Sustainability Reporting Award (SRA) contributes to the usefulness of the information in the financial statements. This study used a sample consisting of 110 winners of SRA (SRA firms) and 110 companies that did not receive SRA (non-SRA firms) from 2008 to 2016. The study found that earnings per share (EPS), book value per share (BVPS), and earnings per share change (EPSC) are value relevant information. Results of comparison between SRA firms and non-SRA fimrs, this study found that EPS positive association with stock price and with returns for SRA firms is higher than that for non-SRA firms. Findings of this study also show that, value relevance of BVPS for non-SRA firms is higher than that for SRA firms. When mesures of Price and BVPS are transformed into natural logarithm, the value relevance of BVPS for SRA firms is higher than that for non-SRA firms. Thus, the results are sensitive to measures of the variables. The findings of this study indicate that information about the winners of SRA contributes to the usefulness of financial statements.

In this study, the physical properties of briquettes produced from two different biomass feedstocks (sawdust and date palm trunk) and different plastic wastes were investigated, without using any external binding agent. The biomass feedstocks were blended with different ratios of two WEEE plastics (halogen-free wire and print circuit boards (PCB)) and automotive shredder residues (ASR). The briquettes production is studied at different waste proportions (10-30%), pressures (22-67 MPa) and temperatures (room-130 ˚C). Physical properties as density and durability rating were measured, usually increasing with temperature. Palm trunk gave better results than sawdust in most cases, due to its moisture content and the extremely fine particles that are easily obtained.

A frequent problem in Geotechnics is the soils with inadequate physical-mechanical properties before the efforts to which they will be subjected by the constructions, incurring cost overruns caused by their engineering improvement. The need to improve the engineering properties of soils is not recent, currently observing that the most common alternatives are binders such as cement and lime. The climate change observed in recent decades and the uncontrolled emission of greenhouse gases have motivated Geotechnical and Geoenvironmental researchers to seek mechanisms for soil reinforcement from a more sustainable and environmentally friendly approach by proposing the use of recycled and waste materials. An alternative is natural fibers, which can be obtained as waste from many agro-industrial processes, implying their high availability and low cost. Sawdust as a by-product of wood processing has a rough texture that can generate high friction between the fiber and the matrix of the soils, leading to a significant increase in its shearing strength and bearing capacity. This concept of improving the properties of soils using natural fibers distributed randomly is inspired by the natural phenomenon of grass and/or plants that when growing on a slope can effectively stabilize a said slope.

Background: The university must take on the challenges that arise at all levels. Within this mechanism, university professors play an important role as facilitators of knowledge. Aim: To analyse the motivations that influence the professional performance of Spanish university professors. Methods: 102 university professors from 9 Spanish public universities participated in the study. [Male: 54 (52.9%); Female: 48 (47.1%)]. A questionnaire of 22 closed-ended Likert-type questions was designed, scoring from 0-10 (do not agree at all, strongly agree). Results: The questionnaire, finally composed of 17 items, showed good internal consistency. (Cronbach's alpha=0.858). The validity analysis showed a value of 0.822 (>0.5) ) in the sample adequacy measure KMO (Kaiser-Meyer-Olkin) and Bartlett's sphericity test (p<0.0001). The exploratory factor analysis showed a clustering in 4 factors (2 for internal goods and 2 for external goods), explaining 64.33% of the total variance. Comparisons between each factor scores by gender (male and female) showed differences statistically significant by gender for factor F1 (higher for females) and F2 (higher for males). Finally, Q1 and Q13 showed a statistically significant correlation (p≤0.05) with years of teaching experience. Conclusions: The motivations of Spanish university professors seem to be associated with the age and gender of the teacher.

Landslides are a global and frequent natural hazard, affecting many communities and infrastructure networks. Technological solutions are needed for long-term, large-scale condition monitoring of infrastructure earthworks, or natural slopes. However, current instruments for slope stability monitoring are often costly, require a complex installation process and/or data processing schemes, or have poor resolution. Wireless sensor networks comprising low-power, low-cost sensors have been shown to be a crucial part of landslide early warning systems. Here, we present the development of a novel sensing approach that uses linear arrays of three-axis accelerometers, used for monitoring soil deformation. By combining these deformation measurements with depth-resolved temperature measurements, we can link our data to subsurface thermal-hydrological regimes where relevant. In this research, we present a configuration of cascaded I2C sensors that (i) have ultra-low power consumption and (ii) enable an adjustable probe length. From an electromechanical perspective, we developed a novel board-to-board connection method that enables narrow, semi-flexible sensor arrays and a streamlined assembly process. The low-cost connection method relies on a specific FR4 printed circuit board design that allows board-to-board press-fitting without using electromechanical components or solder connections. The sensor assembly is placed in a thin, semi-flexible tube (inner diameter 6.35 mm) that is filled with an epoxy compound. The resulting sensor probe is connected to a AA battery powered data logger with wireless connectivity. We characterize the system's electromechanical properties and investigate the accuracy of deformation measurements. Our experiments performed with probes up to 1.8 m long demonstrate long-term connector stability, as well as probe mechanical flexibility. Furthermore, our accuracy analysis indicates that deformation measurements can be performed with a 0.390 mm resolution and a 95% confidence interval of ±0.73 mm per meter of probe length. This research shows the suitability of low-cost accelerometer arrays for distributed soil stability monitoring. In comparison to emerging low-cost measurements of surface displacement, our approach provides depth-resolved deformation, which can inform about shallow sliding surfaces.

MicroRNAs are small non-coding RNAs that are implicated in several physiological processes such as cell development, proliferation, differentiation, apoptosis, immune response and angiogenesis. In the last couple of decades, several studies on miRNA profiling in OSCC have tried to associate miRNAs with clinical characteristics such as relapse, metastasis, and survival, however, the results have been found to vary considerably, sometimes even being contradictory. The main objective of our study was to analyse and verify miRNA expression in oral squamous cell carcinoma in a Spanish population. Second, we attempted to associate the identified deregulated miRNAs with molecular pathways. 8 Oral Squamous Cell Carcinoma patients and 8 healthy control samples were analysed by a microarray Affymetrix® miRNA 4.1 array plate and validated with 8 more cases using RT-qPCR. Deregulated miRNAs were studied using Diana Tools miRPath 3.0 to associate miRNA targets with molecular pathways. Microarray analysis identified 80 deregulated miRNAs (35 over-expressed and 45 under-expressed). Only miR-497-5p and miR-4417 maintained its deregulated expression after validation with qPCR. Among the molecular pathways in which deregulated miRNAs could be implicated, the most statistically significant pathway was ‘proteoglycans in cancer’. No relationship was found between miR-497-5p or miR-4417 expression and clinical or pathological parameters except of nodular affectation (high miR-4417 expression in patients with nodular affectation, p = 0.035) and radiotherapy (diminished miR-497-5p expression in patients who needed radiotherapy, p = 0.05). We have verified the altered expression of miR-497-5p and miR-4417 in Oral Squamous Cell Carcinoma samples and related the deregulated miRNAs with the ‘proteoglycans in cancer’ pathway.

NSD3 is a member of the NSD histone methyltransferase family of proteins. In recent years, it has been identified as a potential oncogene in certain types of cancer. NSD3 gene encodes three isoforms, the full length, a short (NSD3S) and WHISTLE isoforms. Importantly, NSD3S isoform corresponds to the N-terminal of the full-length protein, lacking the methyltransferase domain. The chromosomal location of NSD3 is frequently amplified across cancer types, such as breast, lung, colon, among others. Recently, this amplification has been correlated to a chromothripsis event, that could explain the different NSD3 alterations found in cancer. Fusion proteins containing NSD3 have also been reported, such as leukemia NSD3-NUP98, and in NUT midline carcinoma (NMC), NSD3-NUT fusion. Its role as an oncogene has been described by modulating different cancer pathways through its methyltransferase activity, or the short isoform of the protein, through protein interactions. Specifically, in this review we will focus on stating the functions that have been characterized as methyltransferase dependent, and those that have been correlated with the expression of the NSD3S isoform. Altogether, there is evidence that both isoforms of NSD3 are relevant for cancer progression, establishing NSD3 as a therapeutic target. However, further functional studies are needed to differentiate NSD3 oncogenic activity as dependent or independent of the catalytic domain of the protein, as well as the contribution of each isoform and its clinical significance in cancer progression.

Plastid genomes are in general highly conserved given their slow evolutionary rate, thus large changes in their structure are unusual. However, when specific rearrangements are present, they are often phylogenetically informative. Asteraceae is a highly diverse family whose evolution is long driven by polyploidy (up to 48x) and hybridisation, both processes usually complicating systematic inferences. In this study, we have generated one of the most comprehensive plastome-based phylogenies of family Asteraceae, providing information about the structure, genetic diversity, and repeat composition of these sequences. By comparing the whole plastome sequences obtained, we confirmed the double inversion located in the long single copy region, for most of the species analysed (with the exception of basal tribes), a well-known feature for Asteraceae plastomes. We also show that genome size, gene order and gene content are highly conserved along the family. However, species representative of the basal subfamily Barnadesioideae -as well as in the sister family Calyceraceae - are lacking the pseudogene rps19 located in one inverted repeat. The phylogenomic analysis conducted here, based on 63 protein-coding genes, 30 transfer RNA genes and 21 ribosomal RNA genes from 36 species of Asteraceae, are overall consistent with the general consensus for the family’s phylogeny, while resolving the position of tribe Senecioneae and revealing some incongruences at tribe level between reconstructions based on nuclear and plastid DNA data.

Top-down models are defined by hardware architects to provide information on the utilization of the different hardware components. The target is to isolate the users from the complexity of the hardware architecture while giving them insight into how efficiently the code is using the resources. In this paper, we explore the applicability of 4 top-down models defined for different hardware architectures powering state-of-the-art HPC clusters (Intel Skylake, Fujitsu A64FX, IBM Power9, and Huawei Kunpeng 920) and propose a model for AMD Zen 2. We study a parallel CFD code used for scientific production to compare these 5 Top-Down models. We evaluate the level of insight achieved, the clarity of the information, the ease of use, and the conclusions that each one allows us to reach.

Researchers from around the world are looking for better and cheaper ozone production. One of the methods increasing the efficiency of ozone production is the use to a rotating electrode presented in this paper. Experiments were carried out which shows that the most important parameters are the materials used on the electrodes and the condition of its surface. The metallographic investigations of the electrodes after continuous monthly work was made, which show how the raids layers are formed. As a result of working in a highly oxidizing environment, the electrode is oxidized in the process of chemical corrosion. It is obvious that the layer of corrosion products created during the work of the plasma reactor isolates the surface of the electrode, which reduces the intensity of the electric field, causing a decrease in the amount of plasma generated, which is a direct cause of lowering the concentration of ozone during this process. The dynamics of plasma generation process and the type of electrode material working in changing process conditions are the decisive factors influencing the concentration of ozone produced. The influence of the medium, which is the electrode material, depends mainly on its resistance to corrosion in the environment of dynamically changing conditions, e.g. electrode rotation, oxygen flow through the rotating electric field and the long monthly working time of the plasma reactor.

The publication presents an innovative tower cultivation device designed to significantly increase vertical farming efficiency. The device divides the cultivation system into separate chambers. One division corresponds to the different growth phases of the plants, while another reflects the daily variation in conditions. Each chamber presents slightly different conditions and cultivation patterns from the others. For the early stages, crops are grown horizontally in trays once they mature, transplanted into mobile cultivation towers. The closed circulation of ventilation and irrigation reduces water consumption by up to 95%. A unique separate day-night division optimises light, temperature and humidity conditions, mimicking natural growth patterns. This approach not only saves water and energy but also optimises cultivation in a three-dimensional space. The presented solution focuses on the often overlooked aspects of cultivating in vertical farms and makes this method of growing much more cost-effective and feasible to implement on a large scale.

Users of meteorological forecasts are often faced with the question of whether to make a decision now based on the current forecast or whether to wait for the next and hopefully more accurate forecast before making the decision. One would imagine that the answer to this question should depend on the extent to which there is a benefit in making the decision now rather than later, combined with an understanding of how the skill of the forecast improves, and information about the possible size and nature of forecast changes. We extend the well-known cost-loss model for forecast-based decision making to capture an idealized version of this situation. We find that within this extended cost-loss model, the question of whether to decide now or wait depends on two specific aspects of the forecast, both of which involve probabilities of probabilities. For the special case of weather and climate forecasts in the form of normal distributions we derive a simulation algorithm, and equivalent analytical expressions, for calculating these two probabilities. We apply the algorithm to forecasts of temperature and find that the algorithm leads to better decisions relative to three simpler alternative decision-making schemes. Similar problems have been studied in many other fields, and we explore some of the connections.

There are different ways to analyse energy absorbance (EA) in the human auditory system. In previous research, we developed a complete finite element model (FEM) of the human auditory system. In this mentioned work, the external auditory canal (EAC), middle ear, and inner ear (spiral cochlea, vestibule, and semi-circular canals) were modelled based on human temporal bone histological sections. Multiple acoustic, structure and fluid-coupled analyses were conducted using the FEM to perform harmonic analyses in the 0.1–10 kHz range. Once the FEM had been validated with published experimental data, the FEM numerical results were used to calculate the EA or energy reflected (ER) by the tympanic membrane. This EA was also measured in clinical audiology tests which were used as a diagnostic parameter. A mathematical approach was developed to calculate the EA and ER, with numerical and experimental results showing adequate correlation up to 1 kHz. Another published FEM had adapted its boundary conditions to replicate experimental results. Here, we recalculated those numerical results by applying the natural boundary conditions of human hearing and found that the results almost totally agreed with our FEM. This boundary problem is frequent and problematic in experimental hearing test protocols: the more invasive they are, the more the results are affected. One of the main objectives of using FEMs is to explore how the experimental test conditions influence the results. Further work will still be required to uncover the relationship between the middle ear structure and EA to clarify how to best use FEMs. Moreover, the FEM boundary conditions must be more representative in future work to ensure their adequate interpretation.

Background: Early detection of atrial fibrillation (AF) is essential to prevent stroke and other cardiac and embolic complications. We compared the diagnostic properties for AF detection of the percentage of successive RR interval differences greater than or equal to 30 ms or 3.25% of the previous RR interval (pRR30 and pRR3.25%, respectively), and asymmetric entropy descriptors of RR intervals. Previously, both pRR30 and pRR3.25% outperformed many other heart rate variability (HRV) parameters in distinguishing AF from sinus rhythm (SR) in 60-second electrocardiograms (ECGs). Methods: The 60-s segments with RR intervals were extracted from the publicly available Physionet Long-Term Atrial Fibrillation Database (84 recording, 24-hour Holter ECG). There were 31753 60-s segments of AF and 32073 60-s segments of SR. The diagnostic properties of all parameters were analysed with the receiver operator curve analysis, confusion matrix and logistic regression. The best model with pRR30, pRR3.25% and total entropic features (H) had the largest area under the curve (AUC) – 0.98 compared to 0.959 for pRR30 - and 0.972 for pRR3.25%. However, the differences in AUC between pRR30, pRR3.25% alone and the combined model were negligible from a practical point of view. Moreover, combining pRR30, pRR3.25% with H significantly increased the number of false-negative cases by more than threefold. Conclusions: Asymmetric entropy has some potential in differentiating AF from SR in the 60-s RR interval time series, but the addition of these parameters does not seem to make a relevant difference compared to pRR30 and especially pRR3.25%.

We compare the well known Rayleigh-Ritz variational method (RRVM) with a recently proposed approach based on supersymmetric quantum mechanics and the Gram-Schmidt orthogonalization method (SSQMGS). We apply both procedures to a particular class of double-well harmonic oscillators that had been conveniently chosen for the application of the latter approach. The RRVM eigenvalues converge smoothly from above providing much more accurate results with less computational effort. Present results show that the unproved SSQMGS upper bounds do not hold.

Transcriptional regulation constitutes a key step in gene expression regulation. Myocyte enhancer factor 2C (MEF2C) is a transcription factor of MADS box family involved in the early development of several cell types including muscle cells. Over the last decade a novel layer of complexity modulating gene regulation is emerging as non-coding RNAs have been identified, impacting in both transcriptional and post-transcriptional regulation. microRNAs represent the most studied and abundantly expressed subtype of small non-coding RNAs and their functional role have been widely documented. On the other hand, our knowledge on the transcriptional and post-transcriptional regulatory mechanisms that drive microRNA expression is still incipient. We recently demonstrated that MEF2C is able to transactive the long, but not short, regulatory element upstream of miR-23a-miR-27a-miR-24-2 transcriptional start site. However, MEF2C over-expression and silencing, respectively, displayed distinct effects on each of the miR-23a-miR-27a-miR-24-2 mature cluster members, without affecting pri-miRNA expression levels, supporting thus additional MEF2C-driven regulatory mechanisms. Within this study we demonstrated a complex post-transcriptional regulatory mechanisms directed by MEF2C in the regulation of miR-23a-miR-27a-miR-24-2 cluster members, distinctly involving different domains of the MEF2C transcription factor and the physical interaction with pre-miRNAs and RNA interacting proteins such as Ksrp, HnRNPa3 and Ddx17.

Background: Runners have high incidence of repetitive load injuries, and habitual runners often use smartwatches with embedded IMU sensors to track their performance and training. If accelerometer information from such IMUs can provide information about individual tissue loads, then running watches may be used to prevent injuries. Methods: We investigate a combined physics-based simulation and data-based method. 285 running trials from 76 real runners are subjected to physics-based simulation to recover forces in the Achilles tendon and patella ligament, and the collected data are used to train and test a data-based model using elastic net and gradient boosting methods. Results: Correlations up to 0.95 and 0.71 for the patella ligament and Achilles tendon forces, respectively, are obtained, but no single best predictive algorithm can be identified. Conclusions: Prediction of tissues loads based on body-mounted IMUs appears promising but requires further investigation before deployment as a general option for users of running watches to reduce running-related injuries.

Drones, as mobile media of the present day, increase the operational and narrative capabilities of television and accelerate the logistics of shooting. Unmanned aerial vehicles with a camera properly steered by a pilot are able, to some extent, to replace a jimmy jib/crane and a dolly; basic technical devices, used in the studios, enabling the creation of narrative systems of pictures in film and television. Television is more and more often using drone footage to report events, broadcast live, as well as create coverage and television documentaries. In many productions the pilot of the drone simultaneously acts as the drone camera operator, which can improve the effectiveness of shooting, but also carries some risk related to flight safety. The article describes and presents in the form of processed footage the real conditional ties of a Visual Line of Sight (VLOS) flight faced by pilots filming with a drone. VLOS is a type of air operation, which requires maintaining eye contact with the drone. In many countries a drone visibility flight is legally sanctioned as VLOS Operation. An experiment was conducted to investigate the interactions between a human and a machine in airspace steered using a controller with a touchscreen. The drone pilot was considered an integral part of the drone’s flight system control Experimental data was collected with the use of a mobile eye-tracker, video cameras, surveys and pilot declarations. During the experiment, eight television drone pilot operators recaptured a model shot under the regime of VLOS flight at low altitude. They all show that both advanced and beginner pilots did not look at the UAV for over half the time of shot execution. The experiment allowed establishing two coefficients related to the effectiveness of a VLOS flight aiming at filming from the drone. The results point to clear differences in screen perception styles used by drone television pilots.. The coefficients were described in the form of mathematical formulas and their limit values were determined. The research also determines the limits of pilots’ perception, within which they are able to film with a drone. The outcomes may help to optimize the process of aerial filming with the use of a drone, carried out for television, film and other media, as well as in a simulation of such a flight for research and training. From the perspective of media science and social communication, the presented study included a technological component that can be accessed through information science, using statistical models and variable distributions. Media scholars can study the impact of the media without having to look into the metaphorical black box. Computer science opens up this possibility.

Stagnation is the transient state of a solar thermal system under high solar irradiation where the useful solar gain is zero. Both flat-plate collectors with selective absorber coatings and vacuum-tube collectors exhibit stagnation temperatures far above the saturation temperature of the glycol-based heat carriers within the range of typical system pressures. Therefore, stagnation is always associated with vaporization and propagation of vapor into the pipes of the solar circuit. It is therefore essential to design the system in such a way that vapor never reaches components that cannot withstand high temperatures. In this article, a thermal-hydraulic model based on the integral form of a two-phase mixture model and a drift-flux correlation is presented. The model is applicable to solar thermal flat-plate collectors with meander-shaped absorber tubes and selective absorber coatings. Experimental data from stagnation experiments on two systems, which are identical except for the optical properties of the absorber coating, allowed comparison with simulations carried out under the same boundary conditions. The absorber of one system features a conventional highly selective coating, while the absorber of the other system features a thermochromic coating, which exhibits a significantly lower stagnation temperature. Comparison of simulation results and experimental data show good conformity. This model is implemented into an open-source software tool called “THD” for the thermal-hydraulic dimensioning of solar systems. The latest version of THD, updated by the results of this article, enables planners to achieve cost-optimal design of solar thermal systems and to ensure failsafe operation by predicting the steam range under the initial and boundary conditions of worst-case scenarios.

The study sought to determine solar irradiation in Homa Bay County which can be tapped and utilized in improving lives of residents of the region by converting the solar thermal energy in Home Bay to other forms of energy such as electric form, mechanical form and light. The study was done by assessing the local atmospheric conditions which included sunshine duration data and air temperature records for the period of two years and the data obtained subjected to statistical analysis to determine the localized characteristics of the resource. The characteristics that were examined include; seasonal and annual power expectations as well as resource reliability. The solar irradiance of Home County was found to be 768.0 W/m².

The vertebrate annexin superfamily (AnxA) consists of 12 members of a calcium (Ca²⁺) and phospholipid binding protein family which share a high structural homology. In keeping with this hallmark feature, annexins have been implicated in the Ca²⁺-controlled regulation of a broad range of membrane events. In this review, we identify and discuss several themes of annexin actions that hold a potential therapeutic value, namely the regulation of the immune response and the control of tissue homeostasis, and that repeatedly surface in the annexin activity profile. Our aim is to identify and discuss those annexin properties which might be exploited from a translational science and specifically clinical point of view.

The vertebrate annexin superfamily (AnxA) consists of 12 calcium (Ca2+) and phospholipid binding proteins which share a high structural homology. In keeping with this hallmark feature, annexins have been implicated in the Ca2+-controlled regulation of membrane events. In this review, we discuss several themes of potential therapeutic value, namely the regulation of the immune response and the control of tissue homeostasis, that repeatedly surface in the annexin action profile. Our aim is to identify and discuss those annexin properties which might be exploited from a translational science and specifically clinical point of view.

This study investigates the impact of inoculating Torulaspora delbrueckii (Td) strains during the initial phase of Carbonic Maceration (CM) vinification, aiming to enhance the fermentative process and unique characteristics of CM wines. CM is a winemaking technique where whole bunches (without destemming and crushing) are enclosed in tanks filled with carbon dioxide, inducing intracellular fermentation. The study compares the effects of two Td strains on the MLF performance and sensory characteristics of CM wines, using both inoculated and spontaneous MLF strategies. Although general physicochemical parameters remained consistent across conditions, organoleptic attributes showed significant differences due to T. delbrueckii presence. T. delbrueckii introduction during CM resulted in wines with increased anthocyanin content and a particular volatile profile. Isoamyl acetate, a key aroma in CM wines, was notably elevated, especially in the TdP strain. Sensory evaluations also revealed distinctions, with TdV wines displaying more pronounced aromas of red fruit, banana, and grass. Regarding MLF, T. delbrueckii presence notably enhanced performance, particularly in spontaneous MLF cases, accelerating fermentation completion. Inoculating the Oenococcus oeni strain OoVP41 also shortened MLF duration. These findings highlight the potential of Td strains to improve MLF efficiency and sensory attributes in CM wines. Employing T. delbrueckii strains strategically enables winemakers to optimize MLF and improve sensory profiles, offering an opportunity to produce higher-quality CM wines.

The utilization of eco-fonts for office printing is a sustainable, “green” printing concept, which has obvious economic benefits. As a result, it has a significant effect on environmental sustainability. This practice's fundamental problem is the decreased quality of text printed using eco-fonts compared to those printed with regular fonts. The aim of this research is eco-font efficiency estimation, i.e. determination of toner usage reduction level of inkjet-printed documents typed with this font type, as well as estimation of the extent humans perceive differences between text printed with eco-font and the one printed by its “non-eco“ equivalent. Combining the instrumental measuring method and digital image analysis, it was found that this simple principle (eco-font utilization) enables substantial toner usage reduction for an inkjet printing system. At the same time, a visual test showed that the visual experience of text printed using eco-font was sufficient. In addition, awareness of the benefits that eco-font utilization brings, change users’ attitude towards eco-font quality. The concept of removing the black pixel from this commonly used Thai font has a great potential for the sustainability printing process, and this simple solution could be applied to other languages as part of the GIT campaign.

The enzymatic activities of bacterial isolates have been widely studied, but a spatial distribution of this activity is rarely focused. New antibiotic-producing microorganisms can be discovered in a more efficient manner if spatial statistical techniques are applied to the distribution of the activity of bacterial isolates in different terrains. This study is focused to generate a series of maps illustrating the spatial distribution of different soil parameters and the inhibition against relative-safe pathogens (like Escherichia coli, Staphylococcus aureus, Klebsiella pneumoniae, Salmonella, Pseudomonas fluorencens and Enterobacter cloacae) in an urban park in València (Spain). This spatial data has demonstrated a higher proportion of isolates was specifically allocated. This routine of data presentation is valuable for understanding bacterial population dynamics at a local level.

This paper presents a Multilayer Perceptron and Support Vector Machine algorithms approach to predict the number of COVID19 infections in different countries of America. It intends to serve as a tool for decision-making and tackling the pandemic that the world is currently facing. The models were trained and tested using open data from the European Union repository where a time series of confirmed contagious cases was modeled until May 25, 2020. The hyperparameters as number of neurons per layer were set up using a tabu list algorithm. The countries selected to carry out the study were Brazil, Chile, Colombia, Mexico, Peru and the United States. The metrics used are Pearson's correlation coefficient (CP), Mean Absolute Error (MAE), and Mean Percentage Error (MPE). For the testing stage we obtained the following results: Brazil, CP=0.65, MAE=2508 and MPE=17%; Chile, CP=0.64, MAE=504, MPE=16%; Colombia, CP=0.83, MAE=76, MPE=9%; Mexico, CP=0.77, MAE=231, MPE=9%; Peru, CP=0.76, MAE=686, MPE=18% and the United States of America, CP=0.93, MAE=799, MPE=4%. This resulted in powerful machine learning tools although it is necessary to use specific algorithms depending on the data and the stage of the country’s pandemic.