In this study, changes in the microstructure of coal tar pitch during successive processes, including pyrolysis, polycondensation, and crystallization, were examined in connection with the resulting variations in structure factors, as measured by XRD analysis, and functional groups, as confirmed by FTIR spectroscopy. To this end, four zones were defined based on variations in crystallinity, which were indicated by d002 and Lc. Each zone was further characterized by interpreting crystallinity development in relation to changes in functional groups and specimen height. At around 400 °C, polycondensation occurred as the C-Har and C-Hal peaks decreased in intensity. These peak reductions coincided with the formation of mesophase spheres, resulting in enhanced crystallinity. Subsequently, at around 500 °C, the peak intensity of C-H and COOH decreased, which was attributed to the release of large amounts of gasses. This led to sharp volume changes and a temporary reduction in crystallinity. All these results suggest that changes in the functional groups of coal tar pitch at lower temperatures (600 °C or less) during the carbonization process are closely associated with variations in its crystallinity. The major findings of the present study provide valuable insights for designing highly effective processes in the manufacturing of synthetic graphite blocks using CTP as a binder material, including by selecting appropriate temperature ranges to minimize volume expansion and crystallinity degradation and determining the lowest possible carbonization temperature to ensure adequate binder strength.

Laser shock peening is a process which can reduce stress corrosion cracking and improve fatigue life by forming compressive residual stress on the surface of the material. In a computational FE simulation of laser shock peening, during applying the pressure load generated by the laser pulse to the surface of simulation geometry, the peening is simulated by explicit analysis and then convert to implicit analysis to dissipate the dynamic energy remaining in the geometry. In this study, static damping is applied to dissipate residual dynamic energy without converting it into an implicit analysis. The compressive residual stress distribution is compared between the simulation results for the stainless steel 304 material and the same material subjected to actual laser shock peening. The laser shock peening parameters were 4.2J laser pulse energy, 50% overlap of 3mm diameter of the laser beam and water as a confinement layer. As a result, the compressive residual stress from the surface to the depth direction is similar to both the simulation and the experimental result measured by the hole drilling method.

According to Hofstede’s theory of cultural dimensions, cultures differ in cultural values and norms; values and norms that may influence differences in trendsetting, creative traits and behaviors, and pro-environmental behaviors. Further, because men and women have been socialized within particular cultures, gender differences may exist in trendsetting, creative traits and behaviors, and pro-environmental behaviors. Trendsetters have characteristics that are interrelated with creative traits and behaviors, perhaps inclining them to endorse pro-environmental behaviors. However, the interrelationships among these variables remain unexplored. Thus, the purpose of this study was to examine these three variables among college students in South Korea and the United States, specifically looking at cultural and gender differences. Participants were 225 Korean college students and 221 U.S. college students. Questionnaires included demographic items and scales measuring trendsetting, creative traits and behaviors, and pro-environmental behaviors. Data analyses included descriptive statistics, Cronbach’s alpha reliability, MANOVA, ANOVA and SNK posthoc test. Results show that U.S. (vs Korean) students indicated greater trendsetting and creative traits and behaviors but not greater pro-environmental behaviors. Fashion trendsetting groups in both Korea and the U.S. differed in creative traits and behaviors and pro-environmental behaviors. Among Korean trendsetting groups, reluctant adopters scored lowest on creative traits and behaviors and pro-environmental behaviors. Among U.S. trendsetting groups, trendsetters scored highest on creative traits and behaviors and pro-environmental behaviors; reluctant adopters scored lowest on pro-environmental behaviors. Theoretical and practical implications are provided for researchers and marketers.

Lindera obtusiloba Blume has several activities, such as anti-inflammatory, anti-allergic, anti-tumor, anti-wrinkle, and antioxidant activities. Interleukin-6 (IL-6) is a classic pro-inflammatory cytokine that is associated with various functions, such as proliferation, invasion, inflammatory responses and functions within antioxidant defence systems. In this study, we investigated IL-6-induced STAT3 activation of lignan compounds isolated from L. obtusiloba. The structures of the isolated compounds were elucidated via spectroscopic nuclear magnetic resonance (NMR) and electrospray ionization mass spectrometry (ESI-MS). As a result, seven lignans were identified from L. obtusiloba. All the isolated compounds (1-7) were evaluated for their IL-6-induced STAT3 inhibitory effects in Hep3B cells using a luciferase reporter assay. Of the isolates, compounds 1 and 5 showed inhibitory effects against IL-6-stimulated STAT3 activation. Furthermore, the mRNA expression levels of inflammation-related genes such as CRP, IL-1b, and SOCS3 were significantly reduced by exposure to compound 1 and 5. The protein levels of p-STAT3, p-JAK2 in IL-6 induced U266 cells were regulated in the presence of lignans derived from Lindera obtusiloba by western blot assay. Based on the results, this study of L. obtusiloba demonstrates that the species has promise as a bioactive candidate for the treatment of IL-6-induced STAT3-related disease.

We aimed to determine whether A-mode ultrasound (US) can provide accurate and reliable measurements comparable to those obtained through B-mode US, under diverse conditions. Thirty healthy participants (15 female, 15 male) underwent measurements of subcutaneous fat thickness (SFT), muscle thickness (MT), and muscle quality (MQ) in the trapezius and biceps brachii muscle with both US modes after and before exercises designed to stimulate the respec-tive muscles. In three key indices, the results demonstrated high validity of A-mode, with min-imal mean differences between the two devices less than 0.91mm and intraclass correlation coef-ficients exceeding 0.95 at all measures. Also, Correlation coefficients between error scores and average scores for the trapezius and biceps brachii muscles suggested no evidence of systematic error. The trapezius MT and MQ significantly increased, and biceps brachii MT significantly in-creased after exercise (p<0.05). Notably, both A-mode and B-mode exhibited the same tendency in these post-exercise changes in muscle. This study suggests that low-cost and low-resolution A-mode US provides measurements of SFT, MT, and MQ similar to more expensive, high-resolution B-mode imaging. A-mode US can serve as an affordable and portable alternative for muscle assessment.

(1) Background: The aim of this work was to systematically review existing studies on whether hysteroscopy improves the reproductive outcomes of women with infertility even in the absence of intrauterine pathologies when compared to women who did not receive a hysteroscopy. (2) Methods: We established the Participant-Intervention-Comparison-Outcome strategy and used the Preferred Reporting Items for Systematic Reviews and Meta-Analyses statement to conduct a systematic review of 11 studies which were retrieved from 3 electronic databases: Ovid-Medline, Ovid-Embase, and the Cochrane Library. Two independent investigators extracted the data from the included studies and used the Cochrane risk-of-bias tool to assess their quality. (3) Results: The primary outcome measures were the clinical pregnancy rates (CPRs) and live birth rates (LBRs) in the in vitro fertilization (IVF)/intracytoplasmic sperm injection (ICSI) cycles. Hysteroscopy in infertile women without intrauterine pathologies showed higher CPRs and LBRs than those in the same population who did not receive hysteroscopy in cases of recurrent implantation failure and IVF (odds ratio: 1.79 and 1.46, 95% confidence interval: 1.46-2.30 and 1.08-1.97 for CPR and LBR, respectively); however, the degree of significance was not as high for LBR. (4) Conclusions: Hysteroscopy before IVF/ICSI in infertile women without intrauterine pathologies may potentially be effective in improving the CPRs and LBRs in patients with RIF. Robust and high-quality randomized trials are warranted to confirm this finding.

This study aims to investigate the changes in the structural relationship between alienation in physical education (PE) class, school happiness, and future healthy life expectancy in Korean adolescents after the COVID-19 pandemic. The data were collected from adolescents in the Republic of Korea using scales for these factors. The collected data were analyzed with frequency analysis, reliability analysis, validity analysis, independent t-test, and path analysis. The key results were as follows. First, there were partial changes in each of the parameters since the outbreak of COVID-19. Second, before the pandemic, alienation in PE class negatively affected school happiness, and school happiness positively affected future healthy life expectancy; however, alienation in PE class did not affect future healthy life expectancy showing a complete mediating effect. Third, during the pandemic, alienation in PE class negatively affected school happiness, and school happiness positively affected future healthy life expectancy; alienation in PE class negatively affected future healthy life expectancy, showing a partial mediating effect. These findings emphasize the importance and potential of school education, especially PE, in promoting happiness and healthy life in adolescents. We expect these findings to have practical implications for future research by presenting theoretical and empirical data.

The human oral microbiome refers to an ecological community of symbiotic and pathogenic microorganisms found in the oral cavity. The oral cavity is a suitable environment that provides various kinds of biological niches such as teeth, tongue, and oral mucosa. The oral cavity is the gateway between the external environment and the human body, maintaining oral homeostasis, protecting the mouth, and preventing disease. On the flip side, the oral microbiome plays an important role in triggering, development, and progression of oral and systemic diseases. Currently, disease diagnosis through the analysis of the human oral microbiome has been realized with the recent development of innovative detection technology, and is overwhelmingly promising compared to the previous era. It has been found that patients with oral diseases and systemic diseases have variations in the oral microbiome compared to normal subjects. This narrative review provides insight into the pathophysiological role that oral microbiome plays in influencing oral and systemic diseases, and updates the knowledge related to the oral microbiome over the past 30 years. A wide range of updates was provided with the latest knowledge of the oral microbiome to help researchers and clinicians in both academic and clinical aspects. The microbial community information can be utilized in non-invasive diagnosis and help develop a new paradigm in precision medicine, which will benefit human health in the era of post-metagenomics.

The objective of this study was to determine the effects of supplementing L-isoleucine (L-Ile) on milk protein synthesis, using an immortalized bovine mammary epithelial (MAC-T) cell line. In this case, the cells were treated with 0, 0.3, 0.6, 0.9, 1.2 and 1.5 mM of supplemental Isoleucine (Ile), and the most efficient time for protein synthesis for each amino acid was determined by measuring the cell, medium and total protein at 0, 24, 48, 72 and 96 h. Confirmatory tests showed that 48h incubation time and 0.6 mM dosage of L-Ile are considered as the optimal time and dosage. The mechanism of milk protein synthesis was elucidated through proteomics analysis to clarify the metabolic pathway. When the L-Ile was supplemented, extracellular protein (medium protein) reached a peak at 48h, whereas in the case of the intracellular cell protein, it was shown to have reached to its peak at 24h in all L-Ile dosage treatments. In total, it is noted that there were 63 upregulated and 52 downregulated proteins. The results of the protein pathway analysis showed that the L-Ile group stimulated insulin/IGF pathway-mitogen activated protein kinase kinase/MAP kinase cascade, insulin/IGF pathway-protein kinase B signaling cascade, p53 pathway, de novo purine biosynthesis, Wnt signaling pathway, glycolysis, pentose phosphate pathway, and ATP synthesis which are pathways involved and related to protein and energy metabolism. Together, these results demonstrate that L-Ile supplementation was effective in stimulating β-casein synthesis by stimulating genes and pathways which are significantly related to protein and energy metabolism.

The incidence of carbapenem-resistant Enterobacteriaceae (CRE) has been increasing considerably annually since being first reported in 2008. Gyeonggi Province has the largest number of healthcare facilities in South Korea, which contribute to its regional vulnerability to CRE infections. Thus, there is a need to obtain up to date information on the occurrence of CRE infections in the Gyeonggi Province to take corrective measures. Therefore, in this study, we aimed to investigate the overall trends of CRE occurrence in Gyeonggi Province over the past 4 years and the epidemiological characteristics of CRE-related mortality. Patients admitted to a healthcare facility in Gyeonggi Province from January 2018 to December 2021 with positive blood cultures to CRE were included in the study and investigated. Additionally, the risk factors for CRE-related death were determined using data from CRE-positive patients who died within 30 days of last blood sampling. Older adults aged 70 and over accounted for the highest percentage of both survivors and non-survivors with CRE bacteremia. The number of non-survivors was higher in tertiary hospitals and among patients in intensive care unit. There were no significant differences in the mortality risk according to the use of antibiotics. Moreover, non-survivors were predominant among patients with hypertension, malignant tumor, and those having two or more underlying diseases. Klebsiella pneumoniae was the most common CRE strain in both survivors and non-survivors. Among the survivors, carbapenemase-producing Enterobacteriaceae was detected in 151 cases (71.2%) and 49 cases (23.1%) in the KPC and NDM groups, respectively. Among the non-survivors, it was detected in 25 cases (86.2%) and 5 cases (17.2%) in the KPC and NDM groups, respectively. The endemicity of CRE in South Korea has been proposed for several years; our results have suggested endemicity of CRE in the Gyeonggi Province. Despite the strengthened infection control policies in healthcare facilities during the pandemic, there has been an increasing trend in the isolation of CRE strains in South Korean long-term care hospitals and hospitals within Gyeonggi Province. Factors such as history of hospitalization and underlying diseases have been identified as risk factors for CRE-related deaths. However, to address this issue strictly, it is important to establish infection control infrastructure tailored based on each type of healthcare facility, and elaborate specific government support measures, accordingly.

This work investigates the stability conditions for linear systems with time-varying delays via augmented Lyapunov-Krasovskii functional(LKF). Two types of augmented LKFs with cross terms in integral are suggested to improve the stability conditions for interval time-varying linear systems. Through this work, the compositions of the LKFs are considered to enhance the feasible region of stability criterion for linear systems. Mathematical tools such as Wirtinger-based integral inequality(WBII), zero equalities, reciprocally convex approach, and Finsler’s lemma are utilized to solve the problem of stability criteria. Two sufficient conditions are derived to guarantee the asymptotic stability of the systems using linear matrix inequality(LMI). First, asymptotic stability criteria are induced by constructing the new augmented LKFs in Theorem 1. And then simplified LKFs in Corollary 1 are proposed to show the effectiveness of Theorem 1. Second, asymmetric LKFs are shown to reduce the conservatism and the number of decision variables in Theorem 2. Finally, the advantages of the proposed criteria are verified by comparing maximum delay bounds in two examples. Two numerical examples show that the proposed Theorem 1 and 2 obtained less conservative results than existing outcomes. Also, Example 2 shows that the asymmetric LKF methods of Theorem 2 can provide larger delay bounds and fewer decision variables than Theorem 1’s in some specific systems.

Accurate weight measurement is pivotal for monitoring the growth and well-being of cattle. However, the conventional weighing process, which involves physically placing cattle on scales, is labor-intensive and distressing for the animals. Hence, the development of automated cattle weight prediction techniques assumes critical significance. This study proposes a weight prediction approach for Korean cattle using 3D segmentation-based feature extraction and regression machine learning techniques from incomplete 3D shapes acquired from real farm environments. In the initial phase, we generated mesh data of 3D Korean cattle shapes using a multiple-camera system. Subsequently, deep learning-based 3D segmentation with the PointNet network model was employed to segment two dominant parts of the cattle. From these segmented parts, three crucial dimensions of Korean cattle were extracted. Finally, we implemented five regression machine learning models (CatBoost regression, LightGBM, Polynomial regression, Random Forest regression, and XGBoost regression) for weight prediction. To validate our approach, we captured 270 Korean cattle in various poses, totaling 1190 poses of 270 cattle. The best result was achieved with mean absolute error (MAE) of 25.2 kg and mean absolute percent error (MAPE) of 5.81% using the random forest regression model.

Gastric cancer is the 5th most common disease in the world and the 4th most common cause of death. It is diagnosed through esophagogastroduodenoscopy with biopsy, however there are limitations in finding lesions in the early stages. Recently, research has been actively conducted to use liquid biopsy to diagnose various cancers, including gastric cancer. Various substances derived from cancer are reflected in the blood. By analyzing these substances, it was expected that not only the presence or absence of cancer but also the type of cancer can be diagnosed. However, the amount of these substances is extremely small, and even these have various variables depending on the characteristics of the individual or the characteristics of the cancer. To overcome these, we collected methylated DNA fragments using MeDIP and compared them with normal plasma to characterize gastric cancer tissue or patient’s plasma. And we attempted to diagnose gastric cancer using the characteristics of cancer reflected in the blood through the cancer tissue and patient’s plasma. As a result, we confirmed that the consistency of common methylated fragments between tissue and plasma was approximately 41.2%, and found the possibility of diagnosing and characterizing cancer using the characteristics of the fragments through SFR and 5'end-motif analysis.

This study presents a novel approach for automating the body condition scoring of dairy cows, leveraging advancements in 3D imaging technology and deep neural networks. The primary objective was to design and implement a system capable of accurately and efficiently assessing the body condition of dairy cows, a critical metric in livestock management for optimizing health and productivity. To achieve this, a 3D camera was employed to capture detailed point cloud data, reconstructing the three-dimensional morphology of individual cows. The obtained data were then fed into a deep neural network, specifically tailored for the task of ranking body condition. The neural network was trained on a diverse dataset of annotated body condition score representing varying degrees of body condition, ensuring robust performance across different physiological states. The results demonstrate the efficacy of the proposed system in automatically and objectively scoring the body condition of dairy cows. The automated process not only expedites the assessment but also reduces the subjectivity associated with manual scoring methods. This innovative approach holds promise for improving the efficiency of dairy farm management by providing timely and accurate body condition assessments. The integration of 3D imaging and deep learning techniques paves the way for future advancements in precision livestock farming, contributing to enhanced animal welfare, optimized production, and sustainable agriculture practices.

Purpose:To explore (theoretically) the key parameters and their influence on the time profiles of photosensitizer (riboflavin), free radicals, singlet oxygen, oxygen and the efficacy of corneal collagen crosslinking (CXL)in both type-I and oxygen-mediated type-II mechanisms, specially the role of oxygen and the initiator regeneration. Methodology:Coupled kinetic equations are derived and numerically solved under the quasi-steady state condition for the 2-pathway mechanisms of CXL. The key parameters explored include (bI, V, Q', K, K',Q,P) and their influence on the time profiles of photosensitizer (riboflavin, C), radicals (R), singlet oxygen(S), oxygen (X) and efficacy (E), parameters of (K,K',Q) define the relative strength of type-I and type-II process. The oxygen depletion profile, X(t), and the associated singlet oxygen, S(t), depend on the parameters of V, Q' and the initial value of oxygen. The coupling strength given by (bI) governs almost all profiles, where b is an effective absorption parameter and I is the UV light intensity.Results:Our numerical method for CXL dynamic profiles demonstrated the following important features: (i) Type-I and type-II coexit in CXL, in the presence of oxygen. However, there is no type-II when oxygen is depleted or in a condition without oxygen. (ii) Type-I with bimolecular termination, the radical R(t) is a function of [K'(bIgC)]^0.5, leading to the steady-state efficacy given by a scaling law of 1/(bI)^0.5, in contract to that of type-II which is almost independent to the light intensity. (iii) The depletion rate (2 to 5 minutes) of X(t) is much faster than that of C(t) (10 to 20 minutes), (iv) Thepure type-II profile, has a transition point from straight line to saturating curve and matches the depletion point of singlet oxygen S(t). (v) Improved CXL efficacy of type-I and type-II may be achieved by external supply of photoinitiator (riboflavin) and oxygen, respectively.

The number of fishers working on commercial fishing vessels worldwide is approximately 159,800 according to the Food and Agriculture Organization of the United Nations. The International Labour Organization estimates that the mean annual number of deaths during fishing is approximately 24,000. Most guidelines for the prevention of marine accidents have been developed with a focus on vessels involved in international navigation. As these guidelines may have parts that are unsuitable for application in small-scale boats operating in coastal areas, appropriate modifications are required. This study analyzed quantitative data on 1,790 marine accidents that occurred in trap fishery, a globally common type of fishery, and data obtained through a survey of 101 fishers in South Korea. A guideline to reduce the rate of fatal accidents was developed using the Bayesian network, a method used for the analysis of accidents, as suggested in the formal safety assessment protocol. The results of data analysis and the developed guidelines are expected to be beneficial to all fishers involved in trap fishery across many countries worldwide.

This paper presents a combined optical imaging/artificial intelligence (OI/AI) technique for real-time analysis of tissue morphology at the tip of the biopsy needle, prior collecting a biopsy specimen. This is an important clinical problem as up to 40% of the collected biopsy cores provide low diagnostic value due to high adipose or necrotic content. Micron-scale resolution optical coherence tomography (OCT) images can be collected with a minimally invasive needle probe and automatically analyzed by a computer neural network (CNN)-based AI software. The results can be conveyed to the clinician in real-time and used to select the biopsy location more adequately. This technology was evaluated on a rabbit model of cancer. OCT images were collected with a hand-held custom-made OCT probe. Annotated OCT images were used as ground truth for AI algorithm training. The overall performance of the AI model was very close to that of the humans performing the same classification tasks. Specifically, tissue segmentation was excellent (~99% accuracy) and provided segmentation that closely mimicked ground truth provided by the human annotations, while over 83% correlation accuracy was obtained for tumor and non-tumor classification.

Achievement of solid fusion of the lumbosacral junction (L5-S1 level) is an important factor in adult spinal deformity (ASD) surgery. The purpose of this study is to explore the effectiveness and feasibility of injectable rhBMP-2 (a combination of Eschericia coli-derived rhBMP-2 and hydrogel type β-TCP carrier; NOVOSIS Inject) as a bone substitute for the fusion of lumbosacral junction. 20 patients (average age 69.1 years) diagnosed with ASD with sagittal imbalance who underwent surgical treatment including anterior lumbar interbody fusion (ALIF) in the L5-S1 level were evaluated. Injectable rhBMP-2 was applied in L5-S1 ALIF and followed-up for 1-year. Solid fusion rates and changes of clinical outcomes (Oswestry Disability Index [ODI], Visual Analog Scale [VAS] of back and leg) were measured and analyzed at 6 and 12 months after surgery. All postoperative adverse events were evaluated about the association with injectable rhBMP-2. Fusion rates were 68.4% and 100% at 6 and 12 months after surgery. Compared to baseline, ODI were improved to 45.8% and 63.7%, VAS(back) were improved to 69.2% and 72.8%, and VAS(leg) were improved to 49.2% and 64.8% at 6 and 12 months after surgery (p&lt;0.001, respectively). There were no adverse events associated with injectable rhBMP-2. Thus, injectable rhBMP-2 may be a suitable choice of a bone graft substitute when achieving solid interbody fusion in the lumbosacral junction.

A surgical microscope is large in size, which makes it impossible to be portable. The distance between the surgical microscope and the observation tissue is 15–30 cm, and the adjustment range of the right and left of the camera is a maximum of 30°. Therefore, the surgical microscope is generated attenuation (above 58%) of irradiation optical source owing to the long working distance. Moreover, the observation of tissue is affected because of dazzling by ambient light as the optical source power is strong (55 to 160 mW/cm2). Further, observation blind spot phenomena will occur due to the limitations in adjusting the right and left of the camera. Therefore, it is difficult to clearly observe the tumor. In this study, a compact pen-type probe with a portable surgical microscope is presented. The proposed surgical microscope comprises a small and portable pen-type probe that can adjust the working distance between the probe and the observed tissue. In addition, it allows the adjustment of the viewing angle and fluorescence brightness. The proposed probe has no blind spots or optical density loss.

A surgical microscope is large in size, making portability impossible. The distance between the surgical microscope and the observation tissue is 15 to 30 cm, while the maximum adjustment range of the camera to the right and left is 30°. Therefore, surgical microscopes cause attenuation (above 58%) of the irradiation optical source owing to the long working distance. Moreover, the observation of tissue was dazzled with ambient light because the optical power source was strong (50 to 160 mW/cm2). Owing to the limited ability to adjust the camera to the right and left, a blind spot occurs with a surgical microscope. Therefore, it is difficult to clearly observe a tumor. In this study, a compact pen-type probe with a portable surgical microscope is proposed. The pen-type probe is small with a portable shape, and is capable of adjusting the working distance between itself and the observed tissue. It is also possible to adjust the viewing angle and fluorescence brightness. The proposed pen-type probe has no blind spots or optical density loss.

This study aims to suggest a basis for the selection of technologies for developing high-performance buildings to reduce energy consumptions and greenhouse gas emissions. Energy-saving technologies comprising of 15 cases were categorized into passive, active, and renewable energy systems. EnergyPlus v8.8 was used to analyze the contribution of each technology in reducing the primary energy consumptions and CO₂ emissions in the Korean climate. The primary energy consumptions of the base model were 464.1 and 485.1 kWh/m²a in the Incheon and Jeju, respectively, and the CO₂ emissions were 83.4 and 87.4 kgCO₂/m²a, respectively. Each technology (cases 1–15) provided different energy-saving contributions in the Korean climate depending on their characteristics. The heating, cooling, and other energy-saving contributions of each technology indicate that their saving rates can be used when selecting suitable technologies during the cooling and heating seasons. Case 15 (active chilled beam with dedicated outdoor air system + ground source heat pump) showed the highest energy saving rate. In case 15, the Incheon and Jeju models were reduced by 189.4 (59.2%) and 206.2 kWh/m²a (57.4%) compared to the base case, respectively, and the CO₂ emissions were reduced by up to 32.7 (60.8%) and 35.6 kgCO₂/m²a (59.3%), respectively.

Recently many researches of EOS (Electric Arc Furnace Oxidizing Slag) on application to construction industry have been carried out with increasing its production and limited reclamation site. EOS can be used as a fine aggregate for construction material, however, its engineering properties vary with the manufacturing process and producing district, causing a quality differences in material performance. In the work, EOS is obtained from steel manufacturing plants in South Korea and the engineering properties are evaluated for EOS and the cement mortar with EOS, respectively. From the tests, EOS is mainly made up of CaO, SiO₂, and FeO with 18.2% of larnite which has a crystal structure of β-C₂S with similar cement mineral. EOS mortar shows an increasing compressive strength with more EOS content, which is affected by a considerable amount of larnite (β-C2S) in EOS. The EOS based mortar with ERS (Electric Arc Furnace Reduction Slag) shows unsatisfactory results over the criteria for rate of change, which implies that more consideration must be taken for the usage of the mixed ERS and EOS for cement mortar due to swelling effect of ERS on dimensional stability.

Cyanex 301 and LIX 63 can seletively extract Pd(II) over Pt(IV) from strong hydrochloric acid solutions. Therefore, solvent extraction experiments have been performed by extractant mixtures containing either Cyanex 301 or LIX 63 and the extraction behavior of Pd(II) was compared. Among the mixture of Cyanex 301, the highest synergistic enhancement coefficient was achieved by mixing Cyanex 301 and TOPO. However, it was very diffiuclt to strip the Pd(II) from the loaded mixture. Among the mixture of LIX 63, the mixture of LIX 63 and Alamine 336/TOPO enhanced the extraction of Pt(II). Although the synergistic coefficient by Cyanex 301 + TOPO was higher than that by LIX 63 + Alamine 336, the Pd(II) in the loaded mixture of LIX 63 and Alamine 336 was easily stripped by thiourea.

The objective of this study is to design and synthesize substituted η6-chromium tricarbonyl metal complexes carrying o-carborane units as potential boron neutron capture therapy (BNCT) agents. In this study, 1,2-Diphenyl-o-carborane units were used as starting materials to generate biologically active species. We investigated how the structural changes of 1,2-diphenyl-o-carborane substituted with chromium(0) tricarbonyl affect the biological properties; [(CO)3Cr]Ph2C2 (2) and [(CO)3Cr]2Ph2C2 (3) species were produced in moderate yields. The molecular structures of compounds 1–3 were identified and established by infrared (IR), 1H, 11B, and 13C nuclear magnetic resonance (NMR), and X-ray crystallography analyses. Crystal structures of o-carboranyl chromium complexes 1 [a = 10.859(1) Å, b = 24.953(3) Å, c = 13.938(2) Å, β = 111.854(2)º], 2 [a = 10.621(3) Å, b = 17.056(5) Å, c = 12.174(4) Å, β = 106.622(5)º], and 3 [a = 17.540(2) Å, b = 18.060(2) Å, c = 19.484(4) Å, α = 105.746(2)º, β = 110.226(2)º, γ = 91.256(2)º] were obtained. In vitro study using B16 and CT26 cancer cells containing the triphenyl-o-carboranyl chromium (0) complexes Ph3C2BCr2 and Ph3C2BCr3, which we have previously reported, the compounds 2 and 3 accumulated at higher levels than compounds Ph3C2BCr2 and Ph3C2BCr3. However, the phenylated o-carboranyl chromium(0) complexes have been found to be more cytotoxic than p-boronophenylalanine (BPA).

The cardioprotective effects of volatile anesthetics versus total intravenous anesthesia (TIVA) are controversial, especially in patients undergoing non-cardiac surgery. Using current generation high-sensitivity cardiac troponin (hs-cTn), we aimed to evaluate the effect of anesthetics on the occurrence of myocardial injury after non-cardiac surgery (MINS). From February 2010 to December 2016, 3555 patients without preoperative hs-cTn elevation underwent non-cardiac surgery under general anesthesia. Patients were grouped according to anesthetic agent; 659 patients were classified into a propofol-remifentanil total intravenous anesthesia (TIVA) group, and 2896 patients were classified into into a volatile group. To balance the use of remifentanil between groups, a balanced group (n=1622) was generated with patients who received remifentanil infusion in the volatile group, and two separate comparisons were performed (TIVA vs. volatile and TIVA vs. balanced). The primary outcome was occurrence of MINS, defined as rise of hs-cTn I ≥ 0.04 ng/mL within postoperative 48 hours. The secondary outcomes were 30-day mortality, postoperative acute kidney injury (AKI), and adverse events during hospital stay (mortality, type I myocardial infarction (MI), and new-onset arrhythmia). In propensity-matched analyses, the occurrence of MINS was lower in the TIVA group compared to the volatile group (OR 0.642; 95% CI 0.450-0.914; p = 0.014). However, after balancing the use of remifentanil, there was no difference between groups in the risk of MINS (OR 0.832; 95% CI 0.554-1.251; p-value = 0.377). There were no significant associations between the two groups in type 1 MI, new-onset atrial fibrillation, in-hospital and 30-day mortality before and after balancing the use of remifentanil. However, the incidence of postoperative AKI was lower in the TIVA group (OR 0.362; 95% CI 0.194-0.675; p-value = 0.001). After balancing the use of remifentanil, volatile anesthesia and TIVA showed comparable effects on MINS in patients undergoing non-cardiac surgery without preoperative myocardial injury. Further studies are needed on the benefit of remifentanil infusion.

Cisplatin is a widely used anticancer drug for treating solid tumors, but it is associated with severe side effects, including nephrotoxicity. Various studies have suggested that the nephrotoxicity of cisplatin could be overcome; nonetheless, an effective adjuvant drug has not yet been established. Oleanolic acid acetate (OAA), a triterpenoid isolated from Vigna angularis, is commonly used to treat inflammatory and allergic diseases. This study aimed to investigate the protective effects of OAA against cisplatin-induced apoptosis and necroptosis using TCMK-1 cells and a mouse model. In cisplatin-treated TCMK-1 cells, OAA treatment significantly reduced Bax and cleaved-caspase3 expression, whereas increased Bcl-2 expression. Moreover, in cisplatin-induced kidney injury mouse model, OAA treatment alleviated weight loss in the body and major organs and also relieved cisplatin-induced nephrotoxicity symptoms. RNA sequencing analysis of kidney tissues identified lipocalin-2 as the most upregulated gene by cisplatin. Additionally, necroptosis-related genes such as receptor interacting protein kinase (RIPK) and mixed lineage kinase domain like (MLKL) were identified. In vitro study, the phosphorylation of RIPKs and MLKL was reduced by OAA pretreatment in both cisplatin-treated cells and cells boosted by co-treatment with z-VAD-FMK. In conclusion, OAA could protect the kidney from cisplatin-induced nephrotoxicity and may serve as an anticancer adjuvant.

We report the development of an extrinsic self-healing coating system that shows no fluorescence from the intact coating, yellowish fluorescence in cracked regions, and greenish fluorescence in healed regions, thus allowing the separate monitoring of cracking and healing of coatings. This fluorescence monitoring self-healing system consisted of a top coating, an epoxy matrix resin containing mixed dye-loaded in single microcapsule. The dye-loaded microcapsules consisted of a poly(urea-formaldehyde) shell encapsulating a healing agent containing MAT-PDMS and styrene, a photo-initiator and a mixture of two dyes, one that fluoresces only in the solid state (DCM) and a second that fluoresces dramatically increased in the solid than solution state (4-TPAE). A mixture of the healing agent, photo-initiator and the two dyes was yellow due to fluorescence from DCM. On UV curing of this mixture, however, the color changed from yellow to green and the fluorescence intensity increased due to fluorescence from 4-TPAE in the solid state. When a self-healing coating embedded with microcapsules containing the DCM/4-TPAE dye mixture was scratched, the damaged region exhibited a yellowish color that changed to green after healing. Thus, the self-healing system reported here allows the separate monitoring of cracking and healing based on changes in fluorescence color.

In this study, carbon blocks were fabricated using isotropic coke and coal tar pitch as raw materials, with a variation in pressure during cold isostatic pressing (CIP). The CIP pressure was set to 50, 100, 150, and 200 MPa, and the effect of the CIP pressure on the mechanical and electrical properties of the resulting carbon blocks was analyzed. Microstructural observations confirmed that after the kneading, the surface of isotropic coke was covered with the pitch components. Subsequently, after the CIP, granules, which were larger than isotropic coke and the kneaded particles, were observed. The formation of these granules was attributed to the coalescence of kneaded particles under the applied pressing pressure. This granule formation was accompanied by the development of pores, some remaining within the granules, while others were extruded, thereby existing externally. The increase in the applied pressing pressure facilitated the formation of granules, and this microstructural development contributed to enhanced mechanical and electrical properties. At a pressing pressure of 100 MPa, the maximum flexural strength was achieved at 33.3 MPa, and the minimum electrical resistivity was reached at 60.1 μΩm. The higher the pressing pressure, the larger the size of the granules. Pores around the granules tended to connect and grow larger, forming crack-like structures. This microstructural change led to degraded mechanical and electrical properties. The isotropic ratio of the carbon blocks obtained in this study was estimated based on the coefficient of thermal expansion (CTE). The results confirmed that all carbon blocks obtained proved to be isotropic. In this study, a specimen type named CIP-100 exhibited the best performance in every aspect as an isotropic carbon block.

Increasingly, firms are expected to implement ESG (Environment, Social, and Governance) mandates to appeal to the global market. However, this requires overcoming practical challenges and capitalizing on emerging opportunities. This paper conducts an in-depth analysis of the ESG practices of leading Korean global firms. The study selects five firms for case studies representing industries such as electronics, automotive, steelmaking, and chemicals. It examines ESG reports, performance indicators, and corporate disclosures of these firms. The analysis reveals the adoption of industry-specific ESG strategies, highlighting how these firms tailor their approaches to address unique industry challenges while aligning with global sustainability trends. Key findings include a strong emphasis on innovative solutions to ESG challenges, the integration of ESG into core business operations, and a balanced approach to economic, social, and environmental responsibilities. This study contributes to a broader understanding of how ESG practices are implemented in various industrial contexts, particularly in the dynamic and evolving landscape of Korean global businesses. It offers valuable insights and benchmarks for global companies, underlining the importance of contextualized and industry-specific ESG strategies in achieving sustainable and ethical business practices

Targeted next-generation sequencing (NGS) technology detects specific mutations that can provide treatment opportunities for colorectal cancer (CRC) patients. We included 145 CRC patients who underwent surgery. We analyzed the mutation frequencies of common actionable genes and their association with clinicopathological characteristics and oncologic outcomes using targeted NGS. Approximately 97.9% (142) of patients showed somatic mutations. Frequent mutations were observed in TP53 (70%), KRAS (49%), and APC (47%). TP53 mutations were significantly linked to higher overall stage (p=0.038) and lower disease-free survival (DFS) (p=0.039). ATM mutation was significantly associated with higher tumor stage (p=0.012) and shorter overall survival (OS) (p=0.041). Stage 3 and 4 patients with ATM mutations (p=0.023) had shorter OS, and FBXW7 mutation was significantly associated with shorter DFS (p=0.002). In multivariate Cox regression analysis, ATM mutation was an independent biomarker for poor prognosis of OS (p=0.022). TP53 and FBXW7 mutations are independent biomarkers for poor prognosis of DFS (p=0.042 and 0.030, respectively). A comprehensive analysis of the molecular markers for CRC can provide insights into the mechanisms underlying disease progression and help optimize a personalized therapy.

On October 18, 2017, Chinese President Xi Jinping presented the blueprint for building a modernized socialist nation through the realization of the Xiao Kang (Every nation enjoys a peaceful and affluent life, it is meaningless to eliminate the poor) social construction at the 19th Congress of China. Subsequent to the 2008 financial crisis, the world has moved on to the new economic status of the New Normal. China has also entered the era of “Xinchang Thai,” which is moving from the high-growth to the moderate-growth phase. Therefore, the government of China emphasizes privatization, liberalization, and deregulation. China is also influenced by government policies due to the nature of socialism. This study confirms China’s current stage of economic development based on Barro’s theory. Thus, we use a quantile regression model and examine the correlation between economic growth and functional classification of government expenditure during Xi Jinping's term of office. Furthermore, we selected Korea as a comparative country as the two countries have common features.

In the Korean construction industry, legal and institutional safety management improvements are continually being pursued. However, there was a 4.5% increase in the number of workers’ deaths at construction sites in 2017 compared to the previous year. Failure to wear safety helmets seems to be one of the major causes of the increase in accidents, and so it is necessary to develop technology to monitor whether or not safety helmets are being used. However, the approaches employed in existing technical studies on this issue have mainly involved the use of chinstrap sensors and have been limited to the problem of whether or not safety helmets are being worn. Meanwhile, improper wearing, such as when the chinstrap and harness fixing of the safety helmet are not properly tightened, has not been monitored. To remedy this shortcoming, a sensing safety helmet with a three-axis accelerometer sensor attached was developed in this study. Experiments were performed in which the sensing data were classified whether the safety helmet was being worn properly, not worn, or worn improperly during construction workers’ activities. The results verified that it is possible to differentiate among wearing status of the proposed safety helmet with a high accuracy of 97.0%

This article presents, for the first time, the efficacy and curing depth analysis of photo-thermal dual polymerization in metal (Fe) polymer composites for 3D printing of a 3-component (A/B/M) system based on the proposed mechanism of our group, in which the co initiators A and B are Irgacure-369, and charge-transfer complexes (CTC), respectively; and the monomer M is filled by Fe. Our formulas show the depth of curing (Zc) is an increasing function of the light intensity, but a decreasing function of the Fe and photoinitiator concentrations. Zc is enhanced by the additive [B] which produces extra thermal radical for polymerization under high temperature. The heat (or temperature) increase in the system has two components : (i) due to the light absorption of Fe filler, and (ii) heat released from the exothermic photopolymerization of the monomer. The heat is transported to the additive (or co-initiator) [B] to produce extra radical R' and enhance the monomer conversion function (CF). The Fe filler leads to temperature increase, but also limits the light penetration leading to lower CF and Zc, which could be overcome by the additive initiator [B] in thick polymers. Optimal Fe for maximal CF and Zc are explored theoretically.

Optic nerve sheath diameter (ONSD) can help predict the neurologic outcome of patients with post-cardiac arrest (CA) return of spontaneous circulation (ROSC). We aimed to investigate the effect of ONSD changes before and after CA on neurologic outcomes in patients with ROSC after CA using brain computed tomography (CT). The study included patients hospitalized after CA, who had undergone pre- and post-CA brain CT from January 2001 to September 2020. The patients were divided into good and poor neurologic outcome (GNO and PNO, respectively) groups based on the neurologic outcome at hospital discharge. We performed between-group comparisons of the amount and rate of ONSD changes on brain CT and calculated the area under the curve (AUC) to determine their predictive value for neurologic outcomes. Among the 96 enrolled patients, 25 had GNO. Compared to the GNO group, the PNO group showed significantly higher amount (0.30 vs. 0.63 mm; p=0.030) and rate of change (5.26 vs. 12.29 %; p=0.041). The AUC for predicting PNO was 0.64 (95% CI=0.53–0.73; p=0.04) and patients with a rate of ONSD change &gt;27.2% had PNO with 100% specificity and positive predictive value. Hence, ONSD changes may predict neurologic outcomes in patients with post-CA ROSC.

There is a noticeable absence of health education among college students. This study aimed to evaluate the extent of general nutrition knowledge among Chinese university students and explore its association with eating attitudes. Data were collected from a group of 273 students in Spring of 2023, using a valid and reliable research instrument consisting of three sections: demographic variables, the General Nutrition Knowledge Questionnaire (GNKQ), and the Eating Attitudes Test (EAT-26). The results were analyzed using SPSS, with correlations and t-tests to examine the relationships between nutritional knowledge and dietary attitudes. Furthermore, the present study employed the Random Forest (RF) algorithm, a machine learning technique, utilizing the Mean Decrease Impurity (MDI) method to investigate the influence of various features on participants' eating attitudes. The findings revealed that Chinese university students had an average accuracy of over 60% in their nutritional knowledge, but their understanding of the relationship between diet and disease still needs improvement. Moreover, male students had significantly lower nutritional knowledge than female students, and there was a positive correlation between nutritional knowledge and parents’ income. The study also found a significant correlation between the level of nutritional knowledge and eating attitudes. RF results indicated that family income level exhibited the most substantial impact on the eating attitudes of the participants. The study highlights the need for nutrition education curriculum developers to focus more on improving students' nutritional knowledge, with particular attention given to male students, low-income individuals, and those with an abnormal BMI.

In recent years, the demand for coffee has increased tremendously. During the production process, green coffee beans are traditionally screened manually for defective beans before they are packed into coffee bean packages; however, this method is not only time-consuming but also increases the rate of human error due to fatigue. Therefore, this paper proposed a lightweight deep convolutional neural network (LDCNN) for the quality detection system of green coffee beans, which combined depthwise separable convolution (DSC), squeeze-and-excite block (SE block), skip block, and other frameworks. To avoid the influence of low parameters of the lightweight model caused by the model training process, rectified Adam (RA), lookahead (LA), and gradient centralization (GC) were included to improve efficiency; the model was also put into the embedded system. Finally, the local interpretable model-agnostic explanations (LIME) model was employed to explain the predictions of the model. The experimental results indicated that the accuracy rate of the model could reach up to 98.38% and the F1 score could be as high as 98.24% when detecting the quality of green coffee beans. Hence, it can obtain higher accuracy, lower computing time, and lower parameters. Moreover, the interpretable model verified that the lightweight model in this work is reliable, providing the basis for screening personnel to understand the judgment through its interpretability, thereby improving the classification and prediction of the model.

Licochalcone H (LCH), a regioisomer of licochalcone C derived from the root of Glycyrrhiza inflata. CRC treatment has always been challenged by the development of resistance. We investigated the antiproliferative activity of LCH in oxaliplatin (Ox)-sensitive and -resistant CRC cells. LCH significantly inhibited cell viability and colony growth in both Ox-sensitive and Ox-resistant CRC cells. We found that LCH decreased epidermal growth factor receptor (EGFR) and AKT kinase activities and related activating signaling proteins including phospho (p)-EGFR and pAKT. A computational docking model indicated that LCH may interact with EGFR, AKT1, and AKT2 at the ATP-binding sites. LCH induced ROS generation, as verified by N-acetyl-L-cysteine (NAC) treatment, and increased the expression of the ER stress markers. LCH treatment of CRC cells induced depolarization of MMP and increased. Multi-caspase activity was induced by LCH treatment and confirmed by Z-VAD-FMK treatment. LCH increased the number of subG1 cells and arrested the cell cycle at the G1 phase. LCH inhibits the growth of Ox-sensitive and Ox-resistant CRC cells by targeting EGFR and AKT, and inducing ROS generation and ER stress-mediated apoptosis. Therefore, LCH could be a potential therapeutic agent for improving not only Ox-sensitive but also Ox-resistant CRC treatment.

The gut microbiota has been suggested as an important factor in the pathogenic mechanisms of amyotrophic lateral sclerosis (ALS). This study aimed to investigate whether the intake of different kinds of dietary fiber was related to the disease progression rate (∆FS) and survival time. In total, 272 sporadic ALS patients diagnosed according to the revised EI Escorial criteria were recruited from March 2011 and were followed-up until the occurrence of events or the end of September 2020. The events included percutaneous endoscopic gastrostomy, tracheostomy, and death. Dietary fiber intake was calculated based on a 24-hour dietary recall and classified according to five major fiber-rich foods: vegetables, fruits, grains, legumes, and nuts/seeds. Among the total participants, the group with ∆FS values lower than the mean ∆FS (0.75) was noted in the highest tertiles of total and vegetable fiber intake. Participants with the highest tertile of vegetable fiber intake showed longer survival in the Kaplan–Meier analysis (p = 0.033). Notably, vegetable fiber intake was negatively correlated with pro-inflammatory cytokine (interleukin [IL]-1β, IL-6, and monocyte chemoattractant protein-1) levels in the cerebrospinal fluid. This study showed that vegetable fiber intake could influence the disease progression rate and survival time. Further clinical trials are needed to confirm whether dietary fiber supplementation improves the prognosis of ALS.

Previous studies to recognize negative emotions (e.g. disgust, fear, sadness) for mental health care have used heavy equipment directly attaching electroencephalogram (EEG) electrodes to the head, making it difficult to use in daily life, and they have proposed binary classification methods to determine whether negative emotion or not. To tackle this problem, we propose a negative emotion recognition system to collect multimodal biosignal data such as five EEG signals in an EEG headset and heart rate, galvanic skin response, and skin temperature in a smart band for classifying multiple negative emotions. It consists of android Internet of Things (IoT) application, an oneM2M-compliant IoT server, and a machine learning server. The android IoT application upload the biosignal data to the IoT server. By using the biosignal data stored in the IoT server, the machine learning server recognizes the negative emotions of disgust, fear, and sadness using a multi-class support vector machine (SVM) model with a radial basis function kernel (RBF). The experimental results showed that the multi-class SVM model achieved 93% accuracy when considering all the multimodal biosignal data. Moreover, when considering only data in the smart band, it could achieve 98% accuracy by optimizing the hyper-parameter of the RBF kernel.

We assessed the growth performance, physiological traits, and gene expressions in steers fed with dietary rumen-protected L-tryptophan (RPT) under cold environment. Eight Korean native steers were assigned to two dietary groups, no RPT (Control) and RPT (0.1% RPT supplementation on a dry matter basis), 6 wks. Maximum and minimum temperatures throughout the experiment were 6.7°C and -7.0°C, respectively. Supplementation of 0.1% RPT to a total mixed ration did not increase body weight but had positive effects of elevating average daily gain (ADG) and reducing the feed conversion ratio (FCR) at day 27 and 48. Metabolic parameter showed higher glucose level (at day 27) in the 0.1% RPT group compared to the control group. Real-time PCR analysis showed no significant differences in the expression of muscle (MYF6, MyoD, and Desmin) metabolism genes between the two groups, whereas the expression of fat (PPARγ, C/EBPα, and FABP4) metabolism genes was lower in the 0.1% RPT group than in the control group. Thus, we demonstrate that long-term (6 wks) dietary supplementation of 0.1% RPT was beneficial owing to enhanced growth performance by increasing ADG and glucose level, decreasing FCR, and maintaining homeostasis in immune responses in beef steers during cold environment.

The wind observations for multiple levels (40–200 m) have been conducted for a long time (2016–2020) on Jeju Island of South Korea. This study aims at understanding the vertical and temporal characteristics of lower atmosphere. Jeju Island is a region located at mid-latitude and is affected by seasonal monsoon wind. The maximum wind speed appears in the lower layer during day time and is delayed in the upper layer during latter time in diurnal cycle. In summer season, the surface layer increases up to 160 m during day time via dominant solar radiation effect, which is higher than those for other seasons. However, the maximum wind speed in winter season appears irregularly among altitudes, and the surface layer is ~100 m, which is lower than that in summer season. It can be attributed to the increase in the mean wind speed in diurnal cycle caused by the strong northwestern wind for winter season. These results imply that the relationship between near-surface and higher altitudes is primarily affected by solar radiation and seasonal monsoon winds. These results are expected to contribute to site selection criteria for wind farms and to the assessment concerning planetary boundary layer modeling.

2-(4-Benzyloxy-3-methoxyphenyl)-5-(carbethoxyethylene)-7-methoxy-benzofuran (BMBF), a benzofuran derivative, is an intermediate found in the process of total synthesis of ailanthoidol. Benzofuran derivatives are a class of compounds that possess various biological and pharmacological activities. The present study explored the anti-metastasis effects in hepatocellular carcinoma (HCC). Our preliminary findings indicate that BMBF suppresses the proliferation and changes the morphology of Huh7, an HCC cell line with a mutated p53 gene (Y220C). According to scratching motility assay, noncytotoxic concentrations of BMBF significantly inhibited the motility and migration in Huh7 cells. BMBF upregulated the expression of E-cadherin and downregulated the expression of vimentin, Slug, and MMP9, which are associated with epithelial-mesenchymal-transition (EMT) and metastasis in Huh7 cells. BMBF decreased the expression of integrin α7 and deactivated its downstream signal FAK/AKT and inhibited p53 protein levels. Cell transfection with p53 siRNA resulted in prevention of cell invasion because of the reduced expression of integrin α7, Slug, and MMP-9 in Huh7 cells. BMBF had anti-metastatic effects in PLC/PRF/5, an HCC cell line with R249S, a mutated p53 gene. Our findings indicate that BMBF has anti-metastatic effects in that it downregulates p53 and mediates the suppression of integrin α7, EMT, and MMP-9 in HCC cells with mutated p53 gene.

The rapid growth rate of the elderly population is a serious current issue in most countries, affecting them economically through needed medical treatment and healthcare planning. The priority concern is how to reduce the number of elderly people requiring long-term healthcare and raise the number who are able to live independently. This study executed a behavior assessment of elderly person’s self-reported use of electric scooters and analyzed their degree of acceptance of these assisted living tools, partly through a related factor analysis of our survey instrument. We used this questionnaire survey as our research method, applying SPSS22 software for factor analysis that revealed five survey facets.

Hf1-xZrxO2 (HZO) thin films are versatile materials suitable for advanced ferroelectric semiconductor devices. Previous studies have shown that the ferroelectricity of HZO thin films, can be stabilized by doping them with group III elements at low concentrations. While doping with Y improves the ferroelectric properties, there has been limited research on Y-HZO thin films fabricated using atomic layer deposition (ALD). In this study, we investigated the effects of Y doping cycles on the ferroelectric and electrical properties of as-deposited Y-HZO thin films with vaying compositions fabricated through ALD. The Y-HZO thin films were stably crystallized without the need for post-thermal treatment and exhibited transition behavior depending on the Y-doping cycle and initial composition ratio of the HZO thin films. These Y-HZO thin films offer several advantages, including enhanced dielectric constant, leakage current density, and improved endurance. Moreover, the optimized Y-doping cycle induced a phase transformation that resulted in Y-HZO thin films with improved ferroelectric properties, exhibiting stable behavior without fatigue for up to 1010 cycles. These as-deposited Y-HZO thin films show promise for applications in semiconductor devices that require high ferroelectric properties, excellent electrical properties, and reliable performance with a low thermal budget.

Tenascin C (TNC) is an element of the extracellular matrix (ECM) of various tissues, including the skin, and is involved in modulating ECM integrity and cell physiology. Although skin aging is apparently associated with changes in the ECM, little is known about the role of TNC in skin aging. Here we found that Tnc mRNA level was significantly reduced in the skin tissues of aged mice compared with young mice, consistent with reduced TNC protein expression in aged human skin. TNC-large (TNC-L; 330-kDa) and -small (TNC-S; 240-kDa) polypeptides were observed in conditional media from primary dermal fibroblasts. Both recombinant TNC polypeptides, corresponding to TNC-L and TNC-S, increased the expression of type I collagen and reduced the expression of matrix metalloproteinase-1 in fibroblasts. Treatment of fibroblasts with a recombinant TNC polypeptide, corresponding to TNC-L, induced phosphorylation of SMAD2 and SMAD3. TNC increased the level of TGF-β1 mRNA and upregulated the expression of type I collagen by activating the TGF-β signaling pathway. In addition, TNC also promoted the expression of type I collagen in fibroblasts embedded in a three-dimensional collagen matrix. Our findings suggest that TNC contributes to the integrity of ECM in young skin and to prevention of skin aging.

Some time ago, Kobayashi et al. experimentally studied the so-called Lee-Naughton-Lebed's (LNL) angular effect in strong electric fields [K. Kobayashi, M. Saito, E. Omichi, and T. Osada, Phys. Rev. Lett. \textbf{96}, 126601 (2006)]. They found that strong electric fields split the LNL conductivity maxima in $\alpha$-(ET)$_2$-based organic conductor and hypothetically introduced the corresponding equation for conductivity. In this Letter, for the first time we suggest quantum mechanical theory of the LNL angular oscillations in moderately strong electric fields. In particular, we demonstrate that the obtained by us approximate theoretical formula coincides with the hypothetical one and well describes the above mentioned experiments.

Due to limitation of natural sand from rivers and seas, artificial sand production from large stones or rocks is being increased. However, this sand manufacturing process is dangerous and causes several social problems such as high level of unwanted vibrations or noises. This study investigates vibration characteristics of sand and screen units in artificial sand production plant whose actuating operation is multiple with several different exciting frequencies. As a first step, vibration levels are measured at the sand and screen unit positions using accelerometers in time and frequency domains. The measurement is carried out at two different conditions: activating sand unit only and operating entire facilities such as stone crusher. Vibration signals acquired from several locations of the sand and screen units of the plant are collected and analyzed from waveforms and spectrums of the signals. It is identified that the vibration acceleration level of the screen unit is higher than that of the sand unit. In addition, it is found from the acceleration signals measured at plant office and shipping control center those places are far away from the plant location that the beating phenomenon is occurred by close driving frequencies for several sand units. In this work, the vibration caused from the beating is significantly reduced by adjusting the driving frequencies for the sand units so that they are sufficiently scattered to avoid the beating.

We investigated the efficacy of a Rumex crispus and Cordyceps sinensis mixture made using the Beopje (Korea traditional processing method to remove anti-nutrients and enhance phytochemicals) method to regulate immune cell responses toward nitric oxide (NO) production, pro-inflammatory cytokines, and inflammation related genes in mice splenocytes. The six experimental groups were as follows: control (control), Rc-Cs (Rumex crispus (Rc) and Cordyceps sinensis (Cs) mixture, 6:4), TMC (Taemyeongcheong, commercial healthy drink containing Rc-Cs), LPS (lipopolysaccharide), LPS+Rc-Cs, and LPS+TMC. The Rc-Cs mixture reduced nitric oxide (NO) production in LPS-induced splenocytes. Moreover, Rc-Cs enhanced production of the pro-inflammatory cytokines TNF-α, IFN-γ, IL-1β, and IL-6 compared to the control (no treatment). However, Rc-Cs inhibited production of pro-inflammatory cytokines in LPS-induced splenocytes. In addition, LPS+Rc-Cs also significantly suppressed mRNA expression of IL-1β and IL-6 compared to LPS treatment. Interestingly, Rc-Cs did not increase mRNA levels of iNOS and COX-2, which are inflammation related genes compared to the control, while LPS+Rc-Cs reduced mRNA levels of iNOS and COX-2 compared LPS alone (p < 0.05). TMC showed a similar pattern compared to Rc-Cs. Therefore, Rc-Cs treatment in splenocytes enhanced NO production and pro-inflammatory cytokines compared to the control, whereas Rc-Cs treatment in LPS-induced splenocytes reduced NO production, pro-inflammatory cytokines, and inflammation related genes. Thus, Rc-Cs regulated immune cells responses by increasing pro-inflammatory cytokines in splenocytes and reducing toxin (LPS)-induced inflammation. These results indicate that a Rumex crispus and Cordyceps sinensis mixture (Rc-Cs) and TMC containing Rc-Cs promote immune cells responses and anti-inflammatory activities.

Patients with schizophrenia had higher mortality risks and the role of antipsychotic medications remained inconclusive. In an aging society, elderly schizophrenia patients warrant increased attention. In this study, we aimed to explore medication dosage associations with mortality in schizophrenia patients, using Taiwan's national healthcare database from 2010 to 2014, with 102,964 patients with schizophrenia, and a subgroup of 6,433 elderly patients, compared to an age- and gender-matched control group. The findings revealed that schizophrenia patients with no antipsychotic exposure had the highest mortality risk as compared to the control sample—with a 3.61 and 3.37-fold risk for overall and cardiovascular mortality respectively in age and gender-adjusted model, followed by high, low, and moderate exposure groups. A similar pattern was observed in elderly schizophrenia patients but high exposure to antipsychotics was associated with the highest risk in both overall and cardiovascular mortality in elderly patients, with a 3.01, and 2.95-fold risk), respectively. In conclusion, the use of antipsychotics is beneficial to patients with schizophrenia, with recommended exposure levels being low to moderate. In elderly patients, high antipsychotic exposure was associated with the highest mortality risk. We should pay more attention to antipsychotic dosage in elderly schizophrenia patients.

Thalassemia is a heterogeneous congenital hemoglobinopathy common in the Mediterranean region, Middle East, Indian subcontinent, and Southeast Asia with increasing incidence in Northern Europe and North America due to immigration. Iron overloading is one of the major long-term complications in patients with thalassemia and can lead to organ damage and carcin-ogenesis. Hepatocellular carcinoma (HCC) is one of the most common malignancies in both transfusion-dependent thalassemia (TDT) and non-transfusion-dependent thalassemia (NTDT). The incidence of HCC in patients with thalassemia has increased over time, as better chelation therapy confers a sufficiently long lifespan for the development of HCC. The mechanisms of iron overloading-associated HCC development include the increased　reactive oxygen species (ROS), inflammation cytokines, dysregulated hepcidin, and ferroportin metabolism. The treat-ment of HCC in patients with thalassemia was basically similar to those in general population. However, due to the younger age of HCC onset in thalassemia, regular surveillance for HCC development is mandatory in TDT and NTDT. Other supplemental therapy and experience of novel treatment for HCC in thalassemia population were also reviewed in this article.

This study aimed to demonstrate the existence of antiviral RNA silencing mechanisms in Sclerotinia sclerotiorum by probing wild-type and RNA-silencing-deficient strains of the fungus with an RNA virus and a circular DNA virus. Key silencing-related genes, specifically dicers, were disrupted in order to dissect the RNA silencing pathway and provide useful information on fungal control. Dicers Dcl-1, Dcl-2, and both Dcl-1/Dcl-2- genes were displaced by selective marker(s). Disruption mutants were then compared for changes in phenotype, virulence, susceptibility to viral infection, and small RNA accumulation compared to the wild-type strain. Disruption of Dcl-1 or Dcl-2 resulted in no changes in phenotype compared to wild-type S. sclerotiorum; however, the double dicer mutant strain exhibited slower growth. To examine the effect of viral infection on strains containing null-mutations of Dcl-1, Dcl-2 or both genes, mutants were transfected with full-length RNA transcripts of a hypovirus SsHV2L and copies of a single-stranded DNA mycovirus- SsHADV-1 as a synthetic virus. Results indicate that the ΔDcl-1/Dcl-2 double mutant which was slow growing without virus infection exhibited much more severe debilitation following virus infection. Altered colony morphology including: reduced pigmentation, significantly slower growth, and delayed sclerotial formation. Additionally, there is an absence of virus-derived small RNAs in the virus-infected ∆Dcl-1/Dcl-2 mutant compared to the virus-infected wild-type strain which displays a high percentage of virus-derived small RNA. The findings of these studies suggest that if both dicers are silenced, invasive nucleic acids which include mycoviruses ubiquitous in nature- can greatly debilitate the virulence of fungal plant pathogens.

Recently, generative adversarial networks (GANs) can be used to generate the photo-realistic image from a low-dimension random noise. It is very dangerous that the synthesized or generated image is used on inappropriate contents in social media network. In order to successfully detect such fake image, an effective and efficient image forgery detector is desired. However, conventional image forgery detectors are failed to recognize the synthesized or generated images by using GAN-based generator since they are all generated but manipulation from the source. Therefore, we propose a deep learning-based approach to detect the fake image by combining the contrastive loss. First, several state-of-the-art GANs will be collected to generate the fake-real image pairs. Then, the contrastive will be used on the proposed common fake feature network (CFFN)to learn the discriminative feature between the fake image and real image (i.e., paired information). Finally, a smaller network will be concatenated to the CFFN to determine whether the feature of the input image is fake or real. Experimental results demonstrated that the proposed method significantly outperforms other state-of-the-art fake image detectors.

Organic light-emitting diodes (OLEDs) are energy-efficient; however, the coordinating ligand can affect their stability. Sky-blue phosphorescent Pt(II) complexes with a C^N chelate, fluorinated-dbi (dbi = [1-(2,4-diisopropyldibenzo[b,d]furan-3-yl)-2-phenyl-1H-imidazole]), and acetylactonate (acac)(1)/picolinate (pic)(2) ancillary ligands were synthesized. The molecular structures were characterized using various spectroscopic methods. The Pt(II) coordination sphere in 2 exhibited a distorted square-planar geometry, with several intra- and inter-molecular interactions involving Cπ⋯H/Cπ⋯Cπ stacking. Complex 1 emitted bright sky-blue light (λmax = 485 nm) with a moderate photoluminescent quantum efficiency of 0.37 and short decay time (6.1 µs) compared to those of 2. Time-dependent density functional theory calculations suggested that the electronic transition of 1 arose from ligand(C^N)-centered π–π* transitions combined with metal-to-ligand charge transfer transitions (MLCT), whereas that of 2 arose from MLCT and ligand(C^N)-to-ligand(pic) charge transfer (LLCT), with minimal contribution from the C^N chelate to the lowest unoccupied molecular orbital. Multi-layered phosphorescent OLEDs using 1 as a dopant and a mixed host, 3,3-di(9H-carbazol-9-yl)-1,1-biphenyl:3-di(9H-carbazol-9-yl)-1,1-biphenyl (mCBP)/9-(3’-carbazol-9-yl-5-cyano-biphenyl-3-yl)-9H-carbazole-3-carbonitrile (CNmCBPCN) were successfully fabricated. At a 10% doping of 1, a current efficiency of 13.6 cd A−1 and external quantum efficiency of 8.4 % at 100 cd m−2 were achieved. These results show that the ancillary ligand in phosphorescent Pt(II) complexes must be considered.

In this study, ozone oxidation experiment was carried out for the removal of fluorescent whitening agent which is widely used in textile dyeing and paper industry. The stilbene fluorescent whitening agent has been industrialized since the earliest, and the amount of current production is the highest. Due to the characteristics of the fluorescent whitening agent that cannot be removed by conventional wastewater treatment methods, the fluorescent whitening agent in wastewater treatment has difficulty in using as recycled water in the process. Pre-treatment ozone oxidation experiment was conducted prior to the introduction of Membrane Bio Reactor (MBR) treatment process by converting biodegradable materials into biodegradable materials. The removal efficiencies of fluorescent whitening agents, a diaminostilbene disulfonic acid derivative by ozone oxidation were evaluated by UV254 Scan, COD, T-N and color using a synthetic wastewater sample (COD=433.0 mg/ℓ) and paper and paper mill wastewater (COD=157.2 mg/ℓ).

The work proposes a backtesting analysis in comparison between the Lee-Carter and the Cairns-Blake-Dowd mortality models, employing Italian data. The mortality data come from the Italian National Statistics Institute (ISTAT) database and span the period 1975-2014, over which we computed back-projections evaluating the performances of the models in comparisons with real data. We propose three different backtest approaches, evaluating the goodness of short-run forecast versus medium-length ones. We find that both models were not able to capture the improving shock on the mortality observed for the male population on the analyzed period. Moreover, the results suggest that CBD forecast are reliable prevalently for ages above 75, and that LC forecast are basically more accurate for this data.

The association between obesity and the risk of gliomas remains unclear. We sought to evaluate the potential association between general and abdominal obesity and the risk of gliomas based on a nationwide population-based cohort study of Koreans. Using data from the Korean National Health Insurance System cohort, 6,833,744 people older than 20 years who underwent regular national health examination in both 2009 and 2011 were followed until the end of 2017. We documented 4,771 glioma cases based on an ICD-10 code of C71 during the median follow-up period of 7.30 years. Individuals with a body mass index (BMI) ≥ 25.0 kg/m2 were at significantly higher risk of gliomas than those with a BMI < 25.0 kg/m2 (HR 1.08 CI 1.02-1.15). Individuals with a waist circumference (WC) ≥ 90 cm (males)/85 cm (females) also had a significantly higher risk of gliomas than those with a WC < 90 cm (males)/85 cm (females) (HR 1.16 CI 1.09-1.24). In the group with a BMI ≥ 25.0 kg/m2, individuals with abdominal obesity were at significantly higher risk of gliomas (HR 1.18 CI 1.09-1.27) than those without abdominal obesity. The role of abdominal obesity in this association was stronger in women than in men. To our knowledge, this is the first demonstration that obese people may be at higher risk of gliomas, especially centrally obese people from an Asian population with a BMI ≥ 25.0 kg/m2. Loss of visceral fat in people with abdominal obesity may reduce their risk of gliomas.

Cisplatin-based chemotherapy has long been viewed as the first-line chemotherapy for advanced and metastatic urothelial carcinoma (UC). However, many patients with UC have been classified as “cisplatin-ineligible patient”, which requires alternative chemotherapy due to their poor responses. In fact, vast majority of those who initially responded to cisplatin-based chemotherapy eventually progressed. Understanding of UC tumor immunology provided an immunopathogenic bases for immune checkpoint inhibitors, targeting PD-1 and CTLA-4, to treat cisplatin ineligible metastatic UC and patients with platinum-refractory metastatic UC. In 2020, data from the trail further showed that PD-L1 inhibitors benefit prolonged survival and progression-free survival as maintenance therapy. Besides immune-targeting therapies, manipulation of tumor microenvironment via metabolic pathways alternation, such as inhibiting tumor glycolysis, lactate accumulation and exogenous glutamine uptake, has been investigated in the past few years. In this comprehensive review, we started by introducing traditional chemotherapy of UC, and summarized current evidences supporting the use of immune checkpoint inhibitors and highlighted ongoing clinical trials. Lastly, we reviewed the tumor metabolic characteristic and the anti-tumor treatments targeting metabolic pathways.

This study evaluated various solid-liquid separation (SLS) processes used in pig farms for wastewater and livestock manure. SLS is crucial for recycling and purifying pig manure. Seven SLS processes were tested on 11 farms: centrifuge, centrifuge with coagulation agent, belt press with coagulation agent, drum screen, inclined screen, vibration screen, and screw press. Samples collected included raw manure, separated liquid, and solid manure after SLS processing, analyzed for pH, EC, moisture, COD_Mn, BOD₅, TN, TP, K, TS, SS, NaCl, and heavy metals. Belt press with coagulation agent showed highest TS and SS reduction (78.8% and 96.9%). For TN and TP removal, belt press and centrifuge with coagulation agents achieved 41.0% and 94.2%, respectively. Belt press with coagulation agent removed 59.4% BOD₅ and 66.0% COD_Mn. Centrifuge with coagulation agent removed 100% Zn and 98.6% Cu. Drum screen, inclined screen, vibration screen, screw press, and centrifuge without coagulation showed lower removal efficiency for nutrients, solids, Zn, and Cu compared to centrifugal and belt press with coagulation. Centrifugal and belt press with coagulation showed higher efficiency in removing nutrients, solids, and metals. Further studies are needed to understand its impact on linked biological or chemical processes.

The present study was conducted to evaluate encapsulated essential oils as an alternative anticoccidial in coccidiosis vaccine challenged broiler chickens. A total of 600 day-old male broiler chicks were provided with no-added corn-soybean meal-based control diet or diets that contained either salinomycin or EO at 60 and 120 mg per kg of diet. On day 21, half of the control groups were orally challenged with a coccidiosis vaccine at 25 times higher than the recommended vaccine dose. During 22 to 28 days (i.e., one-week post coccidiosis vaccine challenge), the challenged chickens had decrease (P < 0.05) in body weight gain and feed intake but increase in feed conversion ratio compared with the non-challenged, naïve control chickens. However, dietary EO significantly counteracted (P < 0.05) coccidiosis vaccine-induced depression in body weight gain and feed intake. Increasing dietary EO linearly decreased (P < 0.05) the concentrations of the volatile fatty acids. Dietary SAL and EO affected gut morphology in chickens at 20 days posthatch. Increasing dietary EO linearly (P = 0.073) increased serum catalase activity. Collectively, our study shows that dietary EO increased coccidiosis vaccine-induced growth depression and altered gut physiology in broiler chickens.

The aim of this study is to analyze the characteristics of drought such as intensity, cumulative curves and trends, based on SPEI (Standardized Precipitation Evapotranspiration Index) at 8 stations in Korea from 1981 to 2010. The traditional SPEI is based on Thornthwaite equation for estimating evapotranspiration; SPEI_th. However, a standard of agricultural water management in Korea suggests FAO Penman-Monteith equation; SPEI_pm. In this study, we analyzed the intensity and trends of drought using SPEI_th and SPEI_pm, respectively, and analyzed the relationship between them. Both of central and southern region, the SPEIs were below -1.0 (moderated drought) for the periods May-August in the representative drought year such as 1988, 2001, and 2008-09. The frequency of drought was higher in southern region than central region. In addition, SPEI_pm showed slightly more intensive drought rather than SPEI_th except for Chuncheon and Gwangju. In 5 stations except for Cheoncheon, Gwangju and Jinju, the cumulative probability that SPEI_pm is below -1.5 was significantly increased from 1981-1995 to 1996-2010. As the results of drought trends, the increasing trend of SPEIs was shown on fall season, and the cumulative probability that SPEI_pm is below -1.5 was also significantly increased.

Many studies on magnetorheological fluid (MRF) have been carried out over last three decades several salient advantages such as fast phase change, easy control of the yield stress and so forth. Especially, several review articles of MRF technology have been reported for last two decades summarizing the development of MRFs and their applications. As specific examples, the review articles including the optimization of the particles and carrier liquid to achieve minimum off-state viscosity and maximum yield stress at on-state, the formulation of many constitutive models in-cluding Casson model and Herschel-Bulkley (H-B) model, the sedimentation enhancement using additives and nanosized particles, many types of dampers for automotive suspension and civil structures, medical and rehabilitation devices, MRF polishing technology, the methods of mag-netic circuit design, and the synthesis of various controllers have been published. More recently, the effect of the temperature and thermal conductivity on the properties of MRFs and application systems are actively being investigated by several works. However, there is no review article on this issue so far despite of that the thermal problem is one of crucial factors to be seriously con-sidered for the development of advanced MRFs and commercial products of application systems. In this work, studies on the thermal conductivity and temperature in MRFs themselves and tem-perature-dependent application systems are reviewed, respectively, and principal results are summarized emphasizing on the followings: how to reduce the temperature effect on the field-dependent properties of MRFs and how to design application system to minimize the thermal effect. It is noted here that the review summary is organized in a chronological format using tables.

Lipofibromatous hamartoma, first reported in 1953, is a rare, slowly-progressive soft tissue tumor, characteristics of which include enlargement of the affected nerve by epineurial and perineurial proliferation of adipose and fibrous tissues. Out of previously reported 200 cases of lipofibromatous hamartoma of the median nerve, there have been approximately 40 pediatric cases under the age of 18. Herein, we report a case of lipofibromatous hamatoma of the median nerve in a 3-year-old female patient, who was surgically decompressed by carpal tunnel release only and histologically confirmed. The patient was followed-up on outpatient clinic basis annually along with ultrasonography, and the postoperative 10th year follow-up did not show recurrence or any deficits in motor and sensory functions

Shear connectors are used in steel beam–concrete slabs of composite frame and bridge structures to transfer shear force according to design loads. The existing Y-type perfobond rib shear connectors are designed for girder slabs of composite bridges. Therefore, the rib and transverse rebars of the conventional Y-type perfobond rib shear connectors are extremely large for the composite frames of building structures. We performed push-out tests of stubby Y-type perfobond rib shear connectors for composite frames. These shear connectors have relatively small ribs than conventional Y-type perfobond rib shear connectors. To confirm the shear resistance of these stubby shear connectors, we performed an experiment by using transverse rebars D13 and D16. The results indicate that these shear connectors have suitable shear strength and ductility for application in composite frame structures. The shear strengths obtained using D13 and D16 were not significantly different. However, the ductility of the shear connectors with D16 was 45.1% higher than that of the shear connectors with D13.

Objective: There are currently no known treatment methods for ensuring complete recovery from facial nerve damage. Thus, various basic and clinical studies continue to be conducted to achieve this end. As part of this research, autophagy is being investigated for its role in nerve regeneration. Here, we review the existing literature regarding the involvement and signifi-cance of autophagy in facial nerve injury and regeneration. Methods: A comprehensive litera-ture review was conducted to assess the induction and role of autophagy in facial nerve injury and subsequent regeneration. Results: Studies conducted on rats and mice have demonstrated activation of autophagy and expression of related factors in facial and sciatic nerves. Among the most studied of these factors in relation to degeneration and regeneration of facial and sciatic nerves are LC3II/I, PI3K, mTOR, Beclin-1, ATG3, ATG5, ATG7, ATG9, and ATG12. Conclusion: This analysis indicates that autophagy is involved in the process of nerve regeneration follow-ing facial and sciatic nerve damage. Inadequate autophagy induction or failure of autophagy re-sponses can result in regeneration issues after facial or sciatic nerve damage. Animal studies suggest that autophagy plays an important role in facial and sciatic nerve degeneration and re-generation.

Recently, research on ultra-high-performance concrete (UHPC) with the characteristics of ultra-high strength, high toughness, and high durability has been actively conducted from materials to actual structural applications. However, research on experimental methods that reflect the unique characteristics of UHPC, which are different from those of normal concrete, is insufficient. To solve the difficulties in applying the compressive creep test method for normal concrete to UHPC and to verify the validity of the recently proposed ASTM C 1856 standard test method, this study performed compressive creep tests on UHPC with variables of specimen size, sustained load intensity, fiber length, and strain measuring method. Two types of cylindrical specimens of ϕ100 × 200 mm and ϕ75 × 150 mm were used for a specimen size variable. The sustained load intensities of 10% to 40% based on the specified compressive strength of 150 MPa were applied. Two types of steel fiber lengths of 13 mm and 19.5 mm in the UHPC mix were used as a variable, and three strain measuring methods of the embedded strain gauge method, the attached strain gauge method, and the strain meter with stud measured the change in length of the UHPC specimens. The experimental results showed that the strain meter method using the standard rod had limitations due to the error in the verification process using the standard rod and the observation error of the measurer, and the sustained load intensity is preferable to 15% to 40% of the actual compressive strength. It was found that it is possible to perform a compressive creep test for UHPC using a specimen with a size of ϕ75 mm or more, and the fiber length did not affect the creep behavior of UHPC up to 19.5 mm. As a result of comparing the UHPC creep test results with the creep prediction model, the B3 model was found to most accurately predict the UHPC creep behavior. The creep coefficient pattern of the B3 model was very similar to the measured results, and well reflected the effects of the mixing ratio and compressive strength of UHPC.

Depressive disorder in childhood and adolescence is a highly prevalent mood disorder that tends to recur throughout life. Untreated mood disorders can adversely impact a patient's quality of life and cause socioeconomic loss. Thus, an accurate diagnosis and appropriate treatment is crucial. However, until now, diagnoses and treatments are conducted according to clinical symptoms. Objective and biological validation are lacking. This may result in a poor outcome for patients with depressive disorder. Research has been conducted to identify the biomarkers that are related to depressive disorder. Cumulative evidence has revealed that certain immunologic biomarkers in-cluding brain-derived neurotrophic factor (BDNF) and cytokines, gastrointestinal biomarkers, hormones, oxidative stress, and certain hypothalamus-pituitary axis biomarkers are associated with depressive disorder. This article reviews the biomarkers related to the diagnosis and treatment of pediatric depressive disorders. To date, clinical biomarker tests are not yet available for diagnosis or for the prediction of treatment prognosis. However, cytokines such as Interleukin-2, interfer-on-gamma, tumor necrosis factor-alpha, and BDNF have shown significant results in previous studies of pediatric depressive disorder. These biomarkers have the potential to be used for diagnosis, prognostic assessment, and group screening for those at high risk.

The effect of CO2 pre-treatments on tomato quality prior to cold storage was investigated using physiochemical and transcriptome changes. Three hours CO2 treated fruits were firmer than untreated fruits and had a good appearance even after being transferred from 4°C storage to 20°C for 8 d. CO2 pretreatment with cold storage showed a synergistic effect on delayed ripening through reduced respiration; these tomatoes exhibited a lower lycopene content than untreated fruit under cold storage. Tomatoes treated with 30% CO2 had fewer pits than untreated fruits subjected to chilling temperatures, even after being transferred to 20°C for 8 d. Functional enrichment analyses from transcriptome and metabolome commonly showed that CO2-responsive genes or metabolites were involved in the sucrose and starch and biosynthesis of secondary metabolisms. The most frequently detected domain, ethylene-responsive factor domain and reduced glycolysis provide insights into the mechanism that CO2 regulates tomato quality.

Since 2007, highly pathogenic clade 2.3.2 H5N1 avian influenza A [A(H5N1)] viruses have evolved to clade 2.3.2.1a, b and c, and currently only 2.3.2.1c A(H5N1) viruses circulate in wild birds and poultry. During antigenic evolution, clade 2.3.2.1a and c A(H5N1) viruses acquired both S144N and V223I mutations around the receptor binding site of hemagglutinin (HA), with S144N generating an N-glycosylation sequon. We introduced single or combined reverse mutations, N144S and/or I223V, into the HA gene of clade 2.3.2.1c A(H5N1) virus and generated PR8-derived, 2 + 6 recombinant A(H5N1) viruses. When we compared replication efficiency in embryonated chicken eggs, mammalian cells and mice, the recombinant virus containing both N144S and I223V mutations showed increased replication efficiency in avian and mammalian hosts and pathogenicity in mice. The N144S mutation significantly decreased avian receptor affinity and egg white inhibition, but not all mutations increased mammalian receptor affinity. Interestingly, the combined reverse mutations dramatically increased the thermostability of HA. Therefore, the adaptive mutations possibly acquired to evade avian immunity may decrease viral thermostability as well as mammalian pathogenicity.

Tumor necrosis factor-related apoptosis-inducing ligand (TRAIL) is a promising chemotherapeutic agent because of its selective apoptotic action on cancer cells. However, resistance to TRAIL-induced apoptosis remains a challenge in many cancers. The gintonin-enriched Panax ginseng extract fraction (GEF) has diverse pharmacological benefits. We explored the combined efficacy of GEF and TRAIL in inducing apoptosis in human renal cell carcinoma (RCC) cells. The effect of GEF treatment on viability, clonogenic potential, wound healing, and TRAIL-induced apoptotic signaling of RCC cells was studied in vitro. Our investigation revealed that GEF pre-treatment sensitized RCC cells to TRAIL-induced apoptosis, as evidenced by DNA fragmentation and cell proliferation, colony formation, and migration inhibition. This sensitization was linked to the upregulation of death receptors 4 and 5 and alterations in apoptotic protein expression; notably, decreased expression of Mu-2-related death-inducing gene, a novel anti-apoptotic protein. Our findings underscore the necessity of caspase activation for GEF/TRAIL-induced apoptosis using the pan-caspase inhibitor Z-VAD-FMK. It demonstrates that GEF sensitizes human RCC cells to TRAIL-induced apoptosis by upregulating DR4/5 and modulating apoptotic protein expression. These findings suggest a promising strategy for overcoming TRAIL resistance in cancer therapy and highlight the potential of GEF as a valuable adjunct to TRAIL-based treatments.

The grain size of CVD (Chemical Vapor Deposition) graphene was controlled by changing the precursor gas flow rates, operation temperature, and chamber pressure. Graphene of average grain sizes of 4.1 µm, 2.2 µm, and 0.5 µm were synthesized in high quality and full coverage. The possibility to tailor the thermoelectric conversion characteristics of graphene has been exhibited by examining the grain size effect on the three elementary thermal and electrical properties of σ, S, and k. Electrical conductivity (σ) and Seebeck coefficients (S) were measured in a vacuum for supported graphene on SiO₂/Si FET (Field Effect Transistor) substrates so that the charge carrier density could be changed by applying a gate voltage (V_G). Mobility (µ) values of 529~1042, 459~745, and 314~490 cm²/V·s for the three grain sizes of 4.1 µm, 2.2 µm, and 0.5 µm, respectively, were obtained from the slopes of the measured σ vs. V_G graphs. The power factor (PF), the electrical portion of the thermoelectric figure of merit (ZT), decreased by about one half as the grain size was decreased, while the thermal conductivity (k) decreased by one quarter for the same grain decrease. Finally, the resulting ZT increased more than two times when the grain size was reduced from 4.1 µm to 0.5 µm.

During early embryonic development, fertilized one-cell embryos develop into preimplantation blastocysts and subsequently establish three germ layers through gastrulation during post-implantation development. In recent years, stem cells have emerged as a powerful tool to study embryogenesis and gastrulation without the need for eggs, allowing the generation of embryo-like structures known as synthetic embryos or embryoids. These in vitro models closely resemble early embryos in terms of morphology and gene expression and provide a faithful recapitulation of early pre- and post-implantation embryonic development. Synthetic embryos can be generated through a combinatorial culture of three blastocyst-derived stem cell types, such as embryonic stem cells, trophoblast stem cells, and extraembryonic endoderm cells, or totipotent-like stem cells alone. This review provides an overview of the progress and various approaches in studying in vitro embryogenesis and gastrulation using stem cells. Furthermore, recent findings and breakthroughs in synthetic embryos and gastruloids are outlined. Despite ethical considerations, synthetic embryo models hold promise for understanding mammalian (including human) embryonic development and have potential implications for regenerative medicine and developmental research.

Metal nanoparticles are extensively studied due to their unique chemical and physical properties, which differ from the properties of their respective bulk materials. Likewise, the properties of heterogeneous bimetallic structures are far more attractive than those of single-component nanoparticles. The incorporation of a second metal into the nanoparticle structure alters the surface plasmon resonance and magnetic properties of the bimetallic composite. This review focuses on the enhanced optical and magnetic properties offered by bimetallic nanoparticles and their corresponding impact on biological applications. We summarize the predominant structures of bimetallic nanoparticles, outline their synthesis methods, and highlight their use in biological applications, both diagnostic and therapeutic, which are dictated by their various optical and magnetic properties.

Graphene materials synthesized using direct laser writing (laser-induced graphene; LIG) are fa-vorable sensor materials because of their large surface area, ease of fabrication, and cost effec-tiveness. In particular, LIG decorated with metal nanoparticles (NPs) has been used in various sensors, including chemical sensors and electronic and electrochemical biosensors. However, the effect of metal decoration on LIG sensors remains controversial; hypotheses based on computa-tional simulations do not always match experimental results, and even experimental results re-ported by different researchers have not been consistent. In the present study, we explored the effects of metal decorations on LIG gas sensors, with NO2 and NH3 gases as representative oxi-dizing and reducing agents, respectively. To eliminate unwanted side effects arising from metal salt residues, metal NPs were directly deposited by vacuum evaporation. Although the gas sen-sitivities of the sensors deteriorate upon metal decoration irrespective of the metal work function in the case of NO2 gas, they improve upon metal decoration in the case of NH3 exposure. A careful investigation of the chemical structure and morphology of the metal NPs in the LIG sensors shows that the spontaneous oxidation of metal NPs with a low work function changes the be-havior of the LIG gas sensors and that the sensor behaviors under NO2 and NH3 gases follow different principles.

There is no doubt that seagrass beds constitute one of the most productive ecosystems in shallow coastal waters. Despite this, picoplankton in seagrass ecosystems has received relatively little attention. The purpose of this study was to compare picoplankton growth and mortality rates between seagrass and unvegetated habitats using chamber incubations. We tested two main hypotheses: (i) incubation with seagrass would result in higher bacterial growth rates due to increased DOM release from seagrass photosynthesis, and (ii) Synechococcus spp. would be lower in the presence of seagrass due to competition for inorganic nutrients. Our results showed bacterial growth rates of 2.31 and 2.44 d–1 without and with seagrass, respectively. In seagrass chambers, bacterial growth was higher than that in non-seagrass chambers, suggesting that organic carbon coming from the seagrass community may support bacterial production. Furthermore, we observed a negative Synechococcus spp. growth rate (-0.9 d–1) in the seagrass treatment, likely reflecting nutrient competition with the seagrass. Small-scale chambers proved to be a useful tool for studying the factors controlling spatial and temporal patterns of picoplankton across different habitats. Furthermore, future studies should examine picoplankton growth over a wider range of spatial scales in seagrass beds and adjacent unvegetated sediment.

Semi-continuous data are very common in the social science and economics. In this paper, a Bayesian variable selection procedure is developed to assess the influence of exogenous factors including observed and unobserved on the semi-continuous data. Our formulation is based on the two-part latent variable model with polytomous response. We consider two schemes for the penalties of regression coefficients and factor loadings: the Bayesian spike and slab bimodal prior and the Bayesian lasso prior. Within the Bayesian framework, we implement Markov Chains Monte Carlo sampling method to conduct posterior inference. To facilitate posterior sampling, we recast the logistic model in part one as the norm-like mixture model. Gibbs sampler is designed to draw observations from the posterior. Our empirical results show that with suitable hyper-parameters, the spike and slab bimodal method slightly outperforms the Bayesian lasso in the current analysis. Finally, a real example related to the China household finance survey is analyzed to illustrate the application of the methodology.. .

In mesoscale eddies, chemical properties and biological composition are different from those in surrounding water, due to their unique physical processes. It is unclear how physical-biological coupling occurs in warm-core eddies, particularly since no study has examined the relationship between bacteria and viruses. The purpose of the present study was to examine the influence of anticyclonic warm eddy on the relationship between bacterial and viral abundances as well as viral activity (viral production) in different depths. In the core of warm eddy, bacterial abundance (0.48 to 2.82 ×105 cells mL−1) fluctuated less than that of the outside eddy (1.12 to 7.03×105 cells mL−1). In particular, there was four-folds higher of viral-bacterial abundance ratio (VBR) estimated within the eddy below DCM than the outside eddy. We suggest that prevailing physical forces with downwelling at the center of the anticyclonic warm eddy, viruses can also be transmitted into the deep ocean directly through adsorption on particulate organic matter during sinking. Overall, our findings provide valuable insights into the interaction between bacterial and viral communities and their ecological mechanism within the warm eddy.

We have identified a new human voltage-gated potassium channel (hKv1.3) blocker, NnK-1, in the jellyfish Nemopilema nomurai, based on its genomic information. The gene sequence encoding NnK-1 contains 5,408 base pairs, with five introns and six exons. The coding sequence of the NnK-1 precursor is 894 nucleotides long and encodes 297 amino acids, containing five presumptive ShK-like peptides. An electrophysiological assay demonstrated that the chemically synthesized fifth peptide, NnK-1, is an effective hKv1.3 blocker. A multiple sequence alignment with cnidarian Shk-like peptides, which have Kv1.3-blocking activity, revealed that four residues (3Asp, 25Lys, 33Lys, and 34Thr) of NnK-1, together with six cysteine residues, are conserved. Therefore, we hypothesize that these four residues are crucial for the binding of the toxins to voltage-gated potassium channels.

Cell-penetrating peptides (CPPs), a group of small peptides capable of promoting the transport of molecular cargo across the plasma membrane, have become important tools in promoting the cellular uptake of exogenously delivered macromolecules. GV1001, a peptide derived from a reverse-transcriptase subunit of telomerase (hTERT) and developed as a vaccine against various cancers, reportedly has unexpected CPP properties. Unlike typical CPPs, such as the HIV-1 TAT peptide, GV1001 enabled the cytosolic delivery of macromolecules such as proteins, DNA and siRNA via extracellular heat shock protein 90 (eHSP90) and 70 (eHSP70) complexes. The eHSP-GV1001 interaction may have biological effects in addition to its cytosolic delivery function. GV1001 was originally designed as a MHC class II-binding cancer epitope, but its CPP properties may contribute to its strong anti-cancer immune response relative to other telomerase peptide-based vaccines. Cell signaling via eHSP-GV1001 binding may lead to unexpected biological effects, such as direct anticancer or antiviral effects. In this review, we focus on the CPP effects of GV1001 bound to eHSP90 and ehsp70.

This study focused on the precise detection and concordant analysis of circulating tumor cells (CTCs) to verify the usefulness of CTCs as promising clinical markers. CTCs are traditionally achieved using immune-fluorescence and morphological techniques. By combining two prostate cancer-specific genes (PSA and PSMA) and two epithelial-specific genes (EpCAM and KRT19), the CTC detection efficiency can be enhanced. The detection rates of localized prostate cancer (LPC), locally advanced prostate cancer (LAPC), metastatic hormone-sensitive prostate cancer (mHSPC), and metastatic castration-resistive prostate cancer (mCRPC) were 63.04 % (29/46), 70.59% (34/51), 94.34% (50/53), and 90% (126/140), respectively. Subsequent correlation analysis between the four genes, baseline PSA, and CTC count revealed that only the CTC count correlated with baseline PSA in the localized stages of prostate cancer, whereas all four genes were correlated with baseline PSA and CTC count in the metastatic stages of prostate cancer. The precise detection of CTCs using both numerical and transcriptomic analyses can improve the accuracy of biomarker investigations. This study provides valuable insights into the limitations of serum PSA testing and offers a promising alternative to diagnose and manage prostate cancer via the CTC number and specific genes for prostate cancer.

This study employed a TSMC 0.18-µm 50 V process to establish a high-voltage n-LDMOS structure. In the reference device, the number of floating-poly (poly-2) turns was 7, and the width and spacing of each turn was 1 µm. Although increasing the number of turns reduces the peak field, directly reducing or increasing the number of poly-2 turns is a common practice. The present experiment was realized in three steps, namely fixing the number of occupied area adjustment turns, adjusting the width of each turn, and adjusting the distance between turns. The first step was fixing the number of occupied area adjustment turns. The number of turns was increased from 7 to 9, and the number of turns was reduced to 5 and 3 in the reference group. A reduction in the number of turns led to a greater decrease in the peak field and increase in the breakdown voltage despite the area remaining unchanged. A comparison of the use of three turns with that of seven turns revealed that the maximum electric field decreased by 42%, from 4.17e+3 to 2.46e+3 V/cm, and that the breakdown voltage (VBK) increased from 30.2 to 35.84 V. The second step was adjusting the width of each turn from 1 to 1.4, 1.2, 0.8, and 0.6 µm in the reference group. This increase in width reduced the maximum electric field and led to a greater increase in VBK. When the width was increased to 1.4 µm, the maximum electric field decreased by 29% from 1.95e+3 to 1.4e+3 V/cm, and the VBK increased by 183% from 30.2 to 85.6 V. The third step was adjusting the spacing of each turn from 1 to 1.4, 1.2, 0.8, and 0.6 µm in the reference group. The results revealed that a reduction in the spacing led to a greater reduction in the maximum electric field and an in-crease in the VBK. When the pitch was reduced to 0.6 µm, the maximum electric field decreased by 33%, from 1.95e+3 to 1.32e+3 V/cm, and the VBK increased by 345%, from 30.2 to 134.4 V.

Vascular calcification (VC) is associated with increased cardiovascular risks in patients with chronic kidney disease (CKD). Sodium-glucose cotransporter 2 inhibitors, like empagliflozin, can improve cardiovascular and renal outcomes. We assessed the expression of Runt-related transcription factor 2 (Runx2), interleukin (IL)-1β, IL-6, AMP-activated protein kinase (AMPK), nuclear factor erythroid-2-related factor (Nrf2), and heme oxygenase 1 (HO-1) in inorganic phosphate–induced VC in mouse VSMCs to investigate the mechanisms underlying empagliflozin’s therapeutic effects. We evaluated biochemical parameters, mean artery pressure (MAP), pulse wave velocity (PWV), transcutaneous glomerular filtration rate (GFR), and histology in an in vivo mouse model with VC induced by an oral high-phosphorus diet following a 5/6 nephrectomy in ApoE−/− mice. Compared to the control group, empagliflozin-treated mice showed significant reductions in blood glucose, MAP, PWV, and calcification, as well as increased calcium and GFR levels. Empagliflozin inhibited osteogenic trans-differentiation by decreasing inflammatory cytokine expression and increasing AMPK, Nrf2, and HO-1 levels. Empagliflozin mitigates high phosphate–induced calcification in mouse VSMCs through the Nrf2/HO-1 anti-inflammatory pathway by activating AMPK. Animal experiments suggested that empagliflozin reduces VC in CKD ApoE−/− mice on a high-phosphate diet.

Supplier selection (SC) continues to be a crucial component in manufacturing procurement. Using the PLCC advantages generates revenue and lowers costs more than might be anticipated. Supplier selection (SC) product life cycle cost (SCPLCC) is an important consideration among corporations, SCPLCC problem has become associated with deciding how one supplier should be selected from possible alternatives. Past literature on this topic is limited. We try to close this gap in knowledge. In this study, we attempt to apply two types of goal programming, multiobjective linear programming and revised multichoice goal programming to develop a PLCC-based concept to solve the SCPLCC problem and construct a decision-making tool for application to a case of supply chain management in a Taiwanese light-emitting diode company in the high-tech industry. Our study main contribution Company managers can easily use the two approaches of the SCPLCC model with different parameters to solve SCPLCC model problems. Finally, we are comparing five models found RMCGP with weighted linear goal programming had an adequate effect for application to the PLCC concept for high-technology Company; this cloud makes company decision–makers focus on low PLCC and select a better supplier in sustainable supply chains development.

Supplier selection (SC) product life cycle cost (SCPLCC) is an important consideration among corporations, SCPLCC problem has become associated with deciding how one supplier should be selected from possible alternatives. In this study, we applied two types of goal programming, multiobjective linear programming and revised multichoice goal programming to develop a PLCC-based concept to solve the SCPLCC problem and construct a decision-making tool for application to a case of supply chain management in a Taiwanese light-emitting diode company in the high-tech industry. Our study main contribution Company managers can easily use the two approaches of the SCPLCC model with different parameters to solve SCPLCC model problems. Finally, we comparing five models found RMCGP with weighted linear goal programming had an adequate effect for application to the PLCC concept for high-technology company; this cloud makes company decision–makers focus on low PLCC and select a better supplier in sustainable supply chains goal.

Using the PLCC advantages generates revenue and lowers costs more than might be anticipated. It ensures better decisions by using a more perfect and practical assessment of revenues and costs. Although the supplier selection (SC) product life cycle cost (SCPLCC) is an important consideration among corporations, SCPLCC problem has become associated with deciding how one supplier should be selected from possible alternatives. In this study, we applied two types of goal programming, multiobjective linear programming and revised multichoice goal programming to develop a PLCC-based concept to solve the SCPLCC problem and construct a decision-making tool for application to a case of supply chain management in a Taiwanese light-emitting diode company in the high-tech industry. Our study main contribution Company managers can easily use the two approaches of the SCPLCC model with different parameters to solve SCPLCC model problems. Finally, we comparing five models found RMCGP with weighted linear goal programming had an adequate effect for application to the PLCC concept for high-technology company; this cloud make company decision–makers focus on low PLCC and select better supplier.

Today’s purchasing companies demand an advanced buyer equal of enactment from their supplier while the two parties maintain a respectful connection. Although the supplier selection (SC) product life cycle cost (SCPLCC) is an important consideration among corporations, SCPLCC problem has become associated with deciding how one supplier should be selected from possible alternatives. In this study, we applied two types of goal programming, multiobjective linear programming and revised multichoice goal programming to develop a PLCC-based concept to solve the SCPLCC problem and construct a decision-making tool for application to a case of supply chain management in a Taiwanese light-emitting diode company in the high-tech industry. Our study main contribution Company managers can easily use the two approaches of the SCPLCC model with different parameters to solve SCPLCC model problems. Finally, we comparing five models found RMCGP with weighted linear goal programming had an adequate effect for application to the PLCC concept for high-technology comapny; this cloud make company decision–makers focus on low PLCC and select better supplier.

Protein tyrosine sulfation (PTS), a vital post-translational modification, facilitates protein–protein interactions and regulates many physiological and pathological responses. Monitoring PTS has been difficult owing to the instability of sulfated proteins and the lack of a suitable method for detecting the protein sulfate ester. In this study, we combined an in situ PTS system with an ultra-high-sensitivity polysilicon nanowire field-effect transistor (pSNWFET)-based sensor to directly monitor PTS formation. A peptide containing the tyrosine sulfation site of P-selectin glycoprotein ligand (PSGL)-1 was immobilized onto the surface of the pSNWFET by using 3-aminopropyltriethoxysilane and glutaraldehyde as linker molecules. A coupled enzyme sulfation system consisting of tyrosylprotein sulfotransferase and phenol sulfotransferase was used to catalyze PTS of the immobilized PSGL-1 peptide. Enzyme-catalyzed sulfation of the immobilized peptide was readily observed through the shift of the drain current–gate voltage curves of the pSNWFET before and after PTS. To the best of our knowledge, this is the first study to describe in situ PTS and its direct observation by using semiconductor devices. We expect that this approach can be developed as a next generation biochip for biomedical research and industries.

This study investigated changes in the average BMI of 5th and 6th grade elementary school students in Korea and provided foundational data to suggest the role of physical education for student health and set future directions. The 2019–2021 Physical Activity Promotion System (PAPS) of the Korean Ministry of Education was used. Data corresponding to 5th and 6th grade students (124,693 from 2019, 126,226 from 2020, and 117,809 from 2021) in 1,208 elementary schools in Korea were collected. The BMI was obtained by dividing weight by the square of height (㎏/m2). Repeated measures ANOVA was conducted for data analysis, and confidence intervals were modified through the Bonferroni correction for multiple comparisons. The Greenhouse-Geisser correction was used for effects test. The study findings are: First, the average BMI of 5th and 6th grade elementary school students in Korea increased significantly in 2021 compared to 2019 and 2020. Second, changes in the yearly average BMI showed a significant difference depending on gender and grade. Obesity among 5th and 6th grade elementary school students in Korea increased steadily in 2019–2021, which may be due to a decrease in students’ physical activity. Male students showed a steeper increase, regardless of grade.

Liver receptor homolog-1 (LRH-1) has emerged as a regulator of hepatic glucose, bile acid, and mitochondrial metabolism. However, the functional mechanism underlying the effect of LRH-1 on lipid mobilization has not been addressed. This study investigated the regulatory function of LRH-1 in lipid metabolism during fasting. The wild-type (WT) and LRH-1 liver-specific knockout (LKO) mice were either fed or fasted for 24 h, and the liver and serum were isolated. During fasting, the LRH-1 LKO mice showed greater accumulation of triglycerides in the liver compared to that in WT mice. Interestingly, LRH-1 LKO liver decreased the perilipin 5 (PLIN5) expression and genes involved in β-oxidation. Additionally, the LRH-1 agonist dialauroylphosphatidylcholine also enhanced PLIN5 expression in human cultured HepG2 cells. To identify new target genes of LRH-1, these findings directed to analyze the PLIN5 promoter sequence, which revealed −1620/−1614 to be a putative binding site for LRH-1. This was confirmed by promoter activity and chromatin immuno-precipitation assays. Moreover, fasted WT primary hepatocytes showed increased co-localization of PLIN5 in lipid droplets (LDs) compared to that in fasted LRH-1 LKO primary hepatocytes. Overall, these findings suggest that PLIN5 might be a novel target of LRH-1 to mobilize LDs and manage the cellular needs.

The futures market plays a significant role in hedging and speculating by investors. Although various models and instruments are developed for real-time trading, it is difficult to realize profit by processing and trading a vast amount of real-time data. This study proposes a real-time index futures trading strategy that uses the pattern of KOSPI 200 index futures time series data. We construct a pattern matching trading system (PMTS) based on a dynamic time warping algorithm that recognizes patterns of market data movement in the morning and determines the afternoon's clearing strategy. We adopt 13 and 27 representative patterns and conduct simulations with various ranges of parameters to find optimal ones. Our experimental results show that the PMTS provides stable and effective trading strategies with relatively low trading frequencies. Investor communities that have sustained financial markets are able to make more efficient investments by using the PMTS. In this sense, the system developed in this paper is a sustainable investment technique and helps financial markets achieve efficient sustainability.

In our previous study, a novel barrier processing on a porous low-dielectric constant (low-k) film was developed: an ultrathin Mn oxide on a nitrogen-stuffed porous carbon-doped organosilica film (p-SiOCH(N)) as a barrier of the Cu film was fabricated. To form a better barrier Mn₂O_3-xN film, an additional annealing at 450°C was implemented. In this study, the electrical characteristics and reliability of this integrated Cu/Mn₂O_3-xN/p-SiOCH(N)/Si structure is investigated. The proposed Cu/Mn₂O_3-xN/p-SiOCH(N)/Si capacitors exhibited poor dielectric breakdown characteristics in the as-fabricted stage, although, less degradation was found after thermal stress. Moreover, its time-dependence-dielectric-breakdown electric-field acceleration factor slightly increased after thermal stress, leading to a larger dielectric lifetime in a low electric-field as compared to other MIS capacitors. Furthermore, its Cu barrier ability under electrical or thermal stress was improved. As a consequent, the proposed Cu/Mn₂O_3-xN/p-SiCOH(N) scheme is a promising integrity for back-end-of-line interconnects.

Background/Aims: Conflicting results have been reported regarding the interaction between proton pump inhibitors (PPIs) and clopidogrel. We investigated whether concomitant PPI use influenced the risk of recurrence in patients with stroke and myocardial infarction (MI). Methods: This study used two databases for different designs, the Korean National Health Insurance Service (NHIS) database for a self-controlled case series design, and the national sample cohort of the NHIS database converted to the Observational Medical Outcomes Partnership-Common Data Model version for a cohort study. Results: In the PPI co-prescription group, recurrent hospitalization with stroke occurred in 17.6% of the 8,201 patients with history of stroke, and recurrent MI occurred in 17.1% of the 1,216 patients with history of MI during 1 year. According to the self-controlled case series, the overall relative risk (RR) of recurrent stroke was 2.09 [95% confidence interval (CI); 1.83-2.38], and the RR showed an increasing trend with PPI duration. In the cohort study, there was a higher incidence of recurrent stroke in the PPI co-prescription group [Hazard ratio (HR): 1.34, 95% CI: 1.01-1.76, P=0.04]. The overall RR of recurrent MI was 1.47 (95% CI; 1.02-2.11) in the self-controlled case series; however, there was no statistically significant difference in recurrent MI in the cohort study (HR:1.42, 95% CI:0.79-2.49, P=0.23). The impact of individual PPIs on stroke and MI showed different patterns. Conclusions: PPI co-prescription with clopidogrel was associated with recurrent stroke; however, its association with recurrent MI remains inconclusive. The influence of individual PPIs should be clarified in the future.

3D printing is a non-traditional additive manufacturing process. It is different from the traditional subtractive manufacturing process. It offers exceptional rapid prototyping capabilities and results that traditional subtractive manufacturing methods cannot attain, especially in applications involving curved or intricately shaped components. Despite its advantages, metal 3D printing will face porosity, warpage, and surface roughness issues. These issues will affect the future practical application of the parts indirectly, for example, the structural strength and the parts assembly ca-pability. Therefore, this study compares the qualities of the warpage, weight, and surface rough-ness after milling and grinding processes under the same materials (316L stainless steel) between general rolled steel and 3D additive steel. Experimental results show that 3D printing parts are approximately 13% to 14% lighter than the general rolled steel. The surface roughness performance of 3D printing steel is better than general rolled steel under the same material after milling or grinding processing. The hardness of the 3D printing steel is better than that of the gen-eral rolled steel. The research verifies that 3D additive manufacturing can use surface processing to optimize surface performance and achieve the functions of lightness and hardness.

In a power plant that uses seawater as a coolant, a debris filter is required to remove foreign substances from the seawater, and differential pressure leads to a decrease in the coolant flow rate, leading to a decrease in power generation efficiency. In this study, analysis was performed under different initial flow velocity conditions of 1.5m/s, 2.0m/s, and 2.5m/s for a debris filter used in a power plant to understand flow characteristics in CTCS. The flow and differential pressure characteristics of a CTCS with an installed debris filter were considered in a comparative analysis of velocity, pressure, and turbulent kinetic energy distribution. The results confirmed that a vortex was generated in the pipe with the debris filter, apparently due to the collision of the flow with the bracket of the debris filter. As the flow rate increased, the range of the vortex increased, causing a loss in flow.

We evaluated hexadecyltrimethylammonium bromide (HTAB) for use in radio frequency (RF) applications in which liquid crystals (LCs) are used in layered structures that have various cell gap conditions. HTAB is a surfactant that can self-align vertically on the surface of indium tin oxide (ITO) substrates, and can induce homeotropic alignment of the LCs. For implementing RF devices with HTAB and LCs, we should consider limitations caused by the design conditions which are different from conventional liquid crystal displays such as cell gap. We quantified the concentration of HTAB ([HTAB]) that is necessary to form and maintain a sufficiently dense vertical alignment of 5CB (4-Cyano-4'-pentylbiphenyl). The required [HTAB] for full-homeotropic alignment was proportional to the cell gap until it was too large to support the transfer of the surface alignment to the LC, due to the weak anchoring nature of HTAB. We also showed the phase-change characteristic of the LC mixture depended on [HTAB] for the design of RF devices driven by light or heat. This work may help to guide the development of new approaches to designing efficient RF devices that use LCs.

(1) Background: Ectopic pregnancy (EP) is when fertilized ovum implanted outside of uterine cavity. The incidence was 1.5% to 2.0% of all pregnancies [1, 2]. EP decreases fertility ability [3]. This study focused on the pregnancy rate after EP and various parameters influencing pregnancy. (2) Methods: The data was extracted from National Health Insurance Research Database (NHIRD) during 2000-2013. The study group enrolled women with one EP history. Those who did not have EP was put into the control group. Chi-square/Fisher exact test was performed on category variable and t-test was used on continue variables. (3) Results: The EP group had a higher cumulative rate of conceive, 41.55% than control group, 37.14% and 1.16 times higher risk in developing pregnancy (P&lt;0.001). The conceiving rate was lower than the control group in the first 5 years, but higher than the control group in the 10th to 14th years. (4) Conclusions: The fecundability after EP is lower at the beginning, but regained after long term follow.

The increasing prevalence of obesity and sedentary lifestyles has led to an increased incidence of metabolic syndrome (MetS) worldwide. In Taiwan, middle-aged women are at a greater risk of MetS, type 2 diabetes, and cardiovascular disease than men are because they have more subcutaneous fat and larger waist circumferences compared to men with equal visceral fat levels. This study investigated the effects of calorie restriction supplemented with fish oil (CRF) in middle-aged women with MetS. For 12 weeks, 75 eligible participants were randomly assigned either calorie restriction (CR) or CRF. Both dietary intervention groups were further divided into two age groups: ≤45 and >45 years. The changes in MetS severity, inflammatory status, iron status, and red blood cell fatty acid profile were evaluated. Seventy-one participants completed the trial. Both dietary interventions significantly ameliorated MetS and improved the participants’ inflammatory status. CR significantly increased total iron binding capacity, whereas CRF increased hepcidin levels. Furthermore, CRF significantly increased the n-6/n-3 and arachidonic acid/docosahexaenoic acid ratios. In conclusion, CR and CRF improved the anthropometric and MetS characteristics of early-middle aged women, including body weight, blood glucose levels, triglyceride levels, as well as the scores for the homeostasis model assessment of insulin resistance and quantitative insulin sensitivity cheque index. Dietary intervention was more effective in >45-year-old women than ≤45-year-old women.

Aluminum wire is a common material for wire bonding due to its resistance to oxidation and low price. It does not melt when becoming a free air ball (FAB) during the electronic flame-off (EFO) process with wettability, and is applied by wedge bonding. This study used 20μm Zn-Coated Al-0.5wt.%Si (ZAS) wires to improve the FAB shape after the EFO process, while maintaining stability of the mechanical properties, including the interface bonding strength and hardness. In order to test circuit stability after ball bonding, the current-tensile test was performed. During the experiment, it was found that 80nm ZAS with wire bonding has lower resistance and higher fusing current. For the bias tensile test, the thicker Zn film diffused into the Al-Si matrix easily, after which the strength was reduced. The ball-bond interfaces had no change in their condition before and after the bias. Accordingly, ZAS could be a promising candidate for ball bonding in the future.

Several COVID-19 platforms have been licensed across the world thus far, but vaccine platforms research that can lead to effective antigen delivery is still ongoing. Here, we constructed AdCLD-CoV19 that could modulate humoral immunity by harboring SARS-CoV-2 antigens onto a chimeric adenovirus 5/35 platform that was effective in cellular immunity. By replacing the S1/S2 furin cleavage sequence of the SARS-CoV-2 Spike (S) protein mounted on AdCLD-CoV19 with the linker sequence, high antigen expression was confirmed in various cell lines. The high levels of antigen expression contributed to antigen-specific antibody activity in mice and non-human primates (NHPs) with single vaccination of AdCLD-CoV19. Furthermore, the adenovirus-induced Th1 immune response was specifically raised for the S protein, and these immune responses protected the NHP against live viruses. While AdCLD-CoV19 maintained neutralizing antibody activity against various SARS-CoV-2 variants, it was reduced to single vaccination for β and ο variants, and the reduced neutralizing antibody activity was restored with booster shots. Hence, AdCLD-CoV19 can prevent SARS-CoV-2 with single vaccination, and the new vaccine administration strategy that responds to various variants can maintain the efficacy of the vaccine.

Cervi cornu has been extensively used in traditional medicine as an antioxidant and for the treatment of various disorders, including osteoporosis. However, since it is not easy to separate the active ingredient, absorption is not performed well. In this study, we extracted the low molecular weight (843Da) collagen NP-2007 from cervi cornu by enzyme hydrolyzation, and evaluated the therapeutic effect in a monosodium iodoacetate (MIA)-induced rat osteoarthritis model, and identified their molecular mechanisms. NP-2007 was orally administered at 50, 100, and 200 mg/kg for 21 d. Efficacy was evaluated based on serum parameters, inflammatory mediators, and mor-phological and histopathological analyses of knee joints. Production of matrix metalloproteinases, including MMP-2, MMP-3, and MMP-9, in the serum was higher in MIA-treated rats; however, these levels decreased after NP-2007 treatment. Serum levels of tumor necrosis factor-α, interleukin (IL)-1β, IL-6, and prostaglandin E2 were lower in the NP-2007 group than in the MIA group. Furthermore, the administration of NP-2007 resulted in effective preservation of both the synovial membrane and knee cartilage, and significantly decreased the transformation of fibrous tissue. This study indicates that NP-2007 can prevent and alleviate symptoms of osteoarthritis and have applications as a novel arthritis treatment.

Rottlerin(R) is a natural extract from Mallotus philippensis with antiviral properties. Feline Infectious Peritonitis (FIP) is a fatal disease characterized by systemic granulomatous inflammation and high mortality, with no established prevention or cure. We investigated antiviral effect of liposome loaded R, Rottlerin-liposome(RL) against Feline infectious peritonitis virus (FIPV), the causative agent. We demonstrated that R and RL inhibited FIPV replication in dose dependently with a PKCδ related manner, not only in the early endocytosis step but also in the late step of replication. RL resolved the low solubility issue of rottlerin and improved its inhibition efficacy at the cellular level. Based on these findings, we suggest that RL has a value for further research as a potential antiviral agent against FIPV.