Lodging is a common problem in maize production that seriously impacts yield, quality, and the capacity for mechanical harvesting. Evaluation of site-specific lodging risks requires establishment of a method for multi-year monitoring. In this study, spectral images collected by the Sentinel-2 satellite were processed to obtain three types of data: gray-level co-occurrence matrix texture (GLCM), vegetation indices (VIs), and spectral reflectance (SR). Lodging classification models were then established with Random Forest (RF) using each of the three data types separately (the GLCM, VI, and SR models) and in combination (SR+VI model, SR+GLCM model, VI+GLCM mod-el, and SR+VI+GLCM model). By gradually removing features with low importance scores from the SR+VI+GLCM model and analyzing the changes in the overall accuracy (OA), the optimal set of predictive variables was identified and used to construct the optimal model. A model built us-ing data from a single timepoint in 2021 was tested on data collected at a similar timepoint in 2019 and vice versa to assess interannual model generalizability. The results of this study demon-strate that for monitoring maize lodging, models constructed with a single feature type, the GLCM model had significantly lower accuracy compared to the VI and SR models. During certain growth stages, the model constructed with combined features had significantly higher accuracy in monitoring maize lodging compared to models constructed with a single feature. During the pro-cess of selecting the optimal predictive variables, it was found that the accuracy of the model did not increase as the number of predictive variables increased. The results show that the positive and negative validation models had an accuracy of 96.55% and 95.18%, with kappa values of 0.93 and 0.83, respectively. This indicates that the model has strong generality for the same repro-ductive stage between years. This study provides a detailed method for large-scale maize lodging monitoring, allowing for identification of optimal planting practices to reduce the probability of lodging and ultimately improving regional maize yield and quality.

With the rapid development of wind power generations, the inertial response of wind turbines (WTs) are widely concerned recently, which is important for grid frequency dynamic and stability. This paper recognizes and understands the inertial response of type-3 and type-4 WTs from the view of equivalent internal voltage, in analogy with typical synchronous generators (SGs). Due to the dynamic of the equivalent inertial voltage different from SGs, the electromechanical inertia of WTs is completely hidden. The rapid power control loop and synchronization control loop is the main reasons that the WT's inertial response is disenabled. On the basis of the equivalent internal voltage's dynamic, the existing inertia control method for WTs are reviewed and summarized as three approaches from the view of WT's control, i.e. optimizing the power control or synchronization control or both. At last, the main challenges and issues of these inertia controls are attempted to explain and address.

High-resolution (2 km) high-frequency (hourly) SST data from 2015-2020 provided by the Advanced Himawari Imager (AHI) onboard the Japanese Himawari-8 geostationary satellite positioned over 140.7°E were used to study spatial and temporal variability of the China Coastal Front (CCF) in the East China Sea. The hourly SST data were processed with the Belkin and O’Reilly (2009) algorithm to generate long-term mean monthly maps of SST gradient magnitude (GM) and frontal frequency (FM) using a GM threshold of 0.1°C/km. Horizontal structure of SST field in the vicinity of the CCF was investigated from cross-frontal distributions of SST along 8 parallels from 31°N to 24°N. The high resolution (2 km) monthly distributions of SST along these 8 parallels were used to determine inshore and offshore boundaries of the CCF and calculate the CCF strength defined as the total cross-frontal SST step dSST=Offshore SST – Inshore SST. The CCF emerges in November, fully develops in December and peaks in strength in January-February. The front’s fragmentation and shrinking/weakening begins in February and March, respectively. In winter (December-February), the front’s strength dSST exceeds 5°C offshore the Zhejiang-Fujian coast and could be as high as 7.5°C when nearshore waters cool down to 7°C. In winter, the front’s strength decreases downstream from 31°N to 24°N. The CCF changes its physical nature as the seasons progress. In winter, the CCF is a water mass front between cold and fresh water coming from the north and warm and salty water coming from the south. In summer, the CCF becomes a coastal upwelling front maintained largely by southerly winds. In winter, the CCF’s cross-frontal structure in the SST field is ramp-shaped, with SST increasing monotonously in the offshore direction. In summer, the CCF’s cross-frontal structure in the SST field is V-shaped or U-shaped, featuring a minimum SST formed by cold upwelled water at some distance from the shore. Thus, the summer SST structure effectively consists of two fronts, a nearshore and offshore, with a minimum SST in-between. Across the inshore/offshore front, the SST decreases/increases in the offshore direction. The local bathymetry, especially the relatively steep shelf slope between 20-m and 50-m isobath, steers the front, which does not meander in winter offshore the Zhejiang-Fujian coast. As the cold season progresses, the front’s axis gradually shifts into deeper waters, from ~20 m to ~50 m.

The intestinal microbiota, comprised of bacteria, archaea, and phages, inhabits the gastrointestinal tract of the organism. Male reproductive sterility is currently a prominent topic in medical research. Increasing research suggests that gut microbiota dysbiosis can result in various reproductive health problems. This article specifically investigates the impact of gut microbiota dysbiosis on male reproductive infertility development. Gut microbiota imbalances can disrupt the immune system and immune cell metabolism, affecting testicular growth and sperm production. This dysfunction can compromise the levels of hormones produced and secreted by the endocrine glands, affecting male reproductive health. Furthermore, imbalance of the gut microbiota can disrupt the gut-brain-reproductive axis, resulting in male reproductive infertility. This article will explore how the imbalance of the gut microbiota impacts male reproductive infertility through immune regulation, endocrine regulation, and interactions of the gut-brain-reproductive axis, concluding with recommendations for prevention and treatment.

Background Dietary guidelines typically recommend limiting the intake of fresh red meat, yet evidence linking red meat consumption with adverse health outcomes is inconsistent. Objective To assess the level of evidence from existing systematic reviews and meta-analyses and analyze the association between high consumption of red meat and cancer risk and adverse health outcomes. Methods Eight databases were searched to collect systematic reviews and meta-analyses from database inception to December 2022. Two independent reviewers screened and extracted data and used the AMSTAR 2 tool to evaluate methodological quality of the included studies. Meta-analysis was conducted using STATA 17.0. Results A total of 18 studies were included, of which 5 were rated as high quality, 4 as medium quality, 6 as low quality, and 3 as extremely low quality. Of the 9 SRs/MAs included, primary studies with overlap were identified, and 14 studies were eventually included. The meta-analysis results showed that compared with the lowest intake of red meat, the highest intake of red meat was associated with an increased risk of colorectal cancer (OR 1.21, 95% CI 1.07-1.37), gastric cancer (OR 1.37, 95% CI 1.18-1.59), non-Hodgkin's lymphoma (OR 1.10.95% CI 1.02-1.19), stroke (RR 1.11, 95% CI 1.03-1.20), type 2 diabetes (RR 1.19 95% CI 1.04-1.37), and ischemic heart disease (RR 1.09, 95% CI 1.06-1.12), as well as a negative effect on total cholesterol (WMD 0.264, 95% CI 0.144-0.383), triglycerides (WMD -0.181, 95% CI -0.349 to -0.013), low-density lipoprotein (WMD 0.198, 95% CI 0.065-0.330), and high-density lipoprotein (WMD -0.065, 95% CI -0.109 to -0.020). However, the associations with breast cancer (RR 1.05 95% CI 1.00-1.11), glycemic control (WMD 0.040, 95% CI 0.049-0.129), and changes in body weight status [overweight (β 0.89, 95% CI 0.48-1.64); obesity (β 1.06, 95% CI 0.30-3.71)] were not significant. Conclusions This comprehensive umbrella review suggests that high consumption of red meat may increase the risk of colorectal cancer, gastric cancer, non-Hodgkin lymphoma, stroke, type 2 diabetes, and cardiovascular disease, and that reducing red meat intake is a key modifiable dietary factor for reducing risk. However, there was no significant correlation with breast cancer, kidney stones, age-related eye disease or changes in body weight.

To enhance industrial competitiveness and increase productivity, every country has strived to create a smart factory by introducing technologies such as Internet of Things, big data and artificial intelligence into production line and build cyber-physical system for the purpose of promoting manufacturing efficiency. For mission assignment, production line management or manufacturing field analysis, the location information of employee, machine and material is very essential. To promote manufacturing efficiency, of course, the location information became more important. A Bluetooth low energy (BLE) positioning system for the manufacturing is developed in this research. A "Tag tracking" mechanism is addressed and adopted, which uses Beacon to catch the location information and a BLE receiver is also used to receive the broadcasting information from Beacon. The position information from the BLE receiver will be compared with the data in the database for calculating the location of the target. The status of the target may also be obtained by using the data from the BLE receiver. Comparing with the mobile device, this method can reduce energy consumption and make the maintenance simple and easy. In the real applications, the target may not be limited to human. The "Regional label positioning technology" is also investigated in this research. Defining a suitable zone location and arranging BLE receiver location, and positioning analysis theory are the key factors included in this developed technology. The developed system will be tested for real industry applications. The test results show that the feasibility of this technology.

Establishing an accurate mathematical model is the foundation of simulating the motion of marine vehicles and structures, and it is the basis of modeling-based control design. System identification from observed input-output data is a practical and powerful method. However, for modeling objects with different characteristics and known information, a single modeling framework can hardly meet the requirements of model establishment. Moreover, there are some challenges in system identification, such as parameter drift and overfitting. In this work, three robust methods are proposed for generating ocean hydrodynamic models based on Bayesian regression. Two Bayesian techniques, semi-conjugate linear regression and noisy input Gaussian process regression, are used for parametric and nonparametric gray-box modeling and black-box modeling. The experimental free-running tests of the KVLCC2 ship model and a multi-freedom wave energy converter (WEC) are used to validate the proposed Bayesian models. The results demonstrate that the proposed schemes for system identification of the ship and WEC have good generalization ability and robustness. Finally, the developed modeling methods are evaluated considering the aspects required conditions, operating characteristics and prediction accuracy.

Waterbomb structures are origami-inspired deformable structural components used in new types of robots. They have a unique radially deployable ability that enables robots to better adapt to their environment. In this paper, we propose a series of new waterbomb structures with square, rectangle, and parallelogram base units. Through quasi-static axial and radial compression experiments and numerical simulations, we prove that the parallelogram waterbomb structure has a twist displacement mode along the axial direction. Compared with the square waterbomb structure, the proposed optimal design of the parallelogram waterbomb structure reduces the critical axial buckling load-to-weight ratio by 55.4% and increases the radial stiffness-to-weight ratio by 67.6%. The significant increase in the radial stiffness-to-weight ratio of the waterbomb structure and decrease in the critical axial buckling load-to-weight ratio make the proposed origami pattern attractive for practical robotics applications.

Second messengers, cyclic adenosine 3'-5'-monophosphate (cAMP) and cyclic guanosine 3'-5'-monophosphate (cGMP) are playing important roles in many animal cells by regulating intracellular signaling pathways and modulating cell physiology. Environmental cues like temperature, light and chemical compounds can stimulate cell surface receptors and trigger the generation of second messengers and the following regulations. Spread of cAMP and cGMP is further shaped by cyclic nucleotide phosphodiesterases (PDEs) for orchestration of intracellular microdomain signaling. However, localized intracellular cAMP and cGMP signaling requires further investigation. Optogenetic manipulation of cAMP and cGMP offers new opportunities of spatio-temporally precise study of their signaling mechanism. Light-gated nucleotide cyclases are well developed and applied for cAMP/cGMP manipulation. Recently discovered rhodopsin phosphodiesterase gene from protists established new and direct biological connection between light and PDEs. Light-regulated PDEs are under development and of demand to complete the toolkit of cAMP/cGMP manipulation. In this review, we summarize the state of the art, pros and cons of artificial and natural light-regulated PDEs and discuss potential new strategies of developing light-gated PDEs for optogenetic manipulation.

Post-evaluation of ecological redevelopment is a good method for its achievements. The eco-engineering technologies and achievements of landscape water reconstructed from aquaculture ponds in Shanghai Chenshan Botanical Garden have been introduced in this study. The sediments and water quality were also sampled and tested for basic physicochemical parameters and heavy metal concentration. The ecological redevelopment of landscape water reconstructed from aquaculture ponds was evaluated using the Nemero comprehensive pollution index method. The results shown that nutrients including organic matter, organic nitrogen and their ratio of sediment were found to be in a state of moderate pollution, while their ecological risk of heavy metals was low. Although total nitrogen and total phosphorus of water quality was really higher than that of other indexes, the decline trends of ammonia nitrogen, total nitrogen and total phosphorus was obvious presented over time. In general, this is a good example that redevelopment of water ecosystems from aquaculture ponds using eco-engineering technologies.

The pathogenicity of grapevine geminivirus A (GGVA), a recently identified DNA virus, to grapevine plants remains largely unclear. Here, we report a new GGVA isolate (named GGVAQN) obtained from grapevine ‘Queen Nina’ plants with severe disease symptoms; the infectious clone of GGVAQN (pXT-GGVAQN) was also constructed. Infection assays indicated that Nicotiana benthamiana plants inoculated with GGVAQN display upward leaf curling and chlorotic mottling symptoms. Direct injection of Agrobacterium tumefaciens cells carrying pXT-GGVAQN into roots of in vitro-grown ‘Red Globe’ grape plantlets by syringe led to systemic infection with GGVAQN, and the plants exhibited chlorotic mottling symptoms on their upper leaves, and downward curling, interveinal yellowing, and leaf-margin necrosis symptoms on their lower leaves. Our results provide insights into the pathogenicity of GGVA, and a simple and efficient inoculation method to deliver infectious viral clones to woody perennial plants.

In this paper, under the symmetric entropy and the scale squared error loss functions, we consider the maximum likelihood (ML) estimation and Bayesian estimation of the Shannon entropy and Rényi entropy of the two-parameter inverse Weibull distribution. In the ML estimation, the dichotomy is used to solve likelihood equation. In addition, the approximation confidence interval is given by the Delta method. Because the form of estimation results is more complex in the Bayesian estimation, the Lindley approximation method is used to achieve the numerical calculation. Finally, Monte Carlo simulations and a real data set are used to illustrate the results derived. By comparing the mean square error between the estimated value and the real value, it can be found that the performance of ML estimation of Shannon entropy is better than that of Bayesian estimation, and there is no significant difference between the performance of ML estimation of Rényi entropy and that of Bayesian estimation.

Protein phosphorylation and ADP-ribosylation (ADPr), as two types of post-translational modifications (PTM), are the process of adding phosphate group and ADP-ribose moieties to proteins, respectively. Although both PTM types can occur on many amino acid types, serine is the most common. Serine phosphorylation (pS), serine ADPr (SADPr), and their in situ crosstalks (pSADPr) play essential roles in biological processes. Although in silico classifiers have been developed for predicting pS and SADPr sites, the classifier for predicting pSADPr sites is unavailable. In this study, we developed classifiers to predict pSADPr sites. Specifically, we collected 3250 human pSADPr, 7520 SADPr, 151,227 pS and 80,096 unmodified serine sites. Based on them, we investigated the characteristics of pSADPr sites and constructed three classifiers to predict pSADPr sites from the pS dataset, the SADPr dataset and the protein sequences separately. We built and evaluated five deep-learning classifiers in ten-fold cross-validation and independent test datasets. Three of them (e.g. Convolutional Neural Network with the One-Hot encoding, dubbed CNNOH) performed better than the rest two. For instance, CNNOH had the AUC values of 0.700, 0.914 and 0.954 for recognizing pSADPr sites from the SADPr, pS and unmodified serine sites.Therefore, it is challenging to distinguish pSADPr sites from SADPr sites compared to the other two. It is consistent with our observation that pSADPr's characteristics are more similar to those of SADPr than the rest. Furthermore, we used the classifiers as base classifiers to develop a few stacking-based ensemble classifiers to improve performance. However, none of the ensemble classifiers showed better performances, suggesting that the base classifiers have good enough performances. Finally, we developed an online tool for extensively predicting human pSADPr sites based on the CNNOH classifier, dubbed EdeepSADPr. It is freely available through http://edeepsadpr.bioinfogo.org/.

Nowadays, the increasingly serious environmental pollution and energy problems urgently require internal combustion engine-based transportation vehicles to upgrade or replace, so the new energy transportation vehicles based on hybrid power and fuel cells have gradually stepped on the stage and continue to innovate. The shipping industry is one of the main sources of global greenhouse gas emissions. The development of clean energy ships represented by fuel cells has attracted wide attention. Fuel cell has the advantages of clean, pollution-free and low noise, but it has some disadvantages such as insufficient dynamic response performance and fast performance decay. Limited by the characteristics of a single energy source, a variety of energy sources and bidirectional DC converters are usually mixed together to form a hybrid ship to improve the flexibility, stability and economy of the ship, and enhance its adaptability to complex sea conditions through the reconfiguration of power system energy. Taking fuel cell ferry "FCS Alsterwasser" as the research object, this study proposed an improved equivalent minimum hydrogen consumption energy management strategy based on fuzzy logic control. First, the power system of the modified mother ship was simulated, and a hybrid power system including fuel cell, lithium iron phosphate battery and supercapacitor was proposed. Then, the dynamic system simulation model and double closed loop PI control model are established in MATLAB/Simulink, and the reliability of the model is verified by the simulation analysis of charge and discharge characteristics. Then, the feasibility of the proposed method is demonstrated by designing simulation experiments based on typical working conditions of the mother ship. The simulation results show that under the premise of meeting the load requirements, the control strategy designed in this paper has a better optimization effect than the S-type penalty function in terms of lithium battery power, lithium battery SOC, bus voltage stability and equivalent hydrogen consumption, which improves the stability and economy of the power system, and has certain engineering practical value.

Fuzzy Rule Interpolation (FRI) offers an innovative methodology for inferring outcomes from data points that match no established rules in a sparse fuzzy rule base. Generally, a traditional fuzzy rule-based system suffers from the inability to perform inference while facing an unmatched observation, given a sparse fuzzy rule base that is derived from insufficient data or inadequate human experience and that fails to cover parts of a specific problem domain. Fortunately, starting with a sparse rule base, Fuzzy Rule Interpolation (FRI) can help to formulate interpolated rules specifically in instances where observations fail to activate any existing rule. An interpolated rule gives a result called consequent, which is related to the unmatched observation so that the inference system will not fail to generate an outcome corresponding to the observation as the output. Conventionally, these interpolated rules will be discarded after obtaining outcomes. However, valuable information may be potentially embedded within those discarded rules addressing the limitation regarding the coverage of the original sparse knowledge space. Moreover, without exploiting the potential value of the interpolated rules, the fuzzy inference system based on a sparse rule base will never improve its efficiency and robustness in the long run. Therefore, this underscores the necessity for Dynamic Fuzzy Rule Interpolation (D-FRI), which aims to collate interpolated rules that cover particular knowledge spaces absent in the sparse rule base. Intuitively, those frequently appeared interpolated rules are considered valuable because future observations are more likely to hit the respective problem areas. Promoting selected interpolated rules to the sparse rule base can enhance the overall coverage of the knowledge space and increase the inference efficiency over time. This paper introduces a framework for Dynamic Fuzzy Rule Interpolation that integrates the widely used Transformation-based Fuzzy Rule Interpolation (T-FRI) with an effective form of clustering of interpolated results. Experimental findings validate the effectiveness of this approach.

During public health events, Active Mobility (walking and cycling) plays an important role in securing residents' travel. To enhance the resilience of urban transportation, this article integrates the travel environment elements for walking and cycling and constructs a travel environment for Active Mobility evaluation index system. This article uses survey data from the main urban area of Harbin in the context of the COVID-19 pandemic in May 2022, and combines the Gradient Boosting Decision Tree (GBDT) and Impact-Asymmetry Analysis (IAA) methods to analyze the satisfaction of the travel environment for Active Mobility. It proposes strategies for optimizing the travel environment for Active Mobility, ensuring residents' travel during public health events, guiding them to adopt Active Mobility, and improving urban transportation resilience. This research shows that Active Mobility can enhance urban transportation resilience. In addition, there are differences in resident demand for walking and cycling environments in the travel environment for Active Mobility. Residents are more concerned about the comfort of the walking environment, while they prioritize the convenience of the cycling environment.

Yaw misalignment can make a wake steer, which is an effective method to increase the power of wind farms, but it also increases the fatigue load of the turbines. In this paper, the method of combining yaw misalignment and pitch control (CYMP) is proposed to investigate the potential to mitigate wake interference, the wind velocity distribution and turbulence distribution in the wake, as well as the power and load changes of the wind turbine are studied, focusing on power in-crement and fatigue damage reduction. Although some studies have found that the method of CYMP are beneficial to increase power generation and reduce fatigue loads, there are no papers that have made a detailed analysis of the effects of wake turbulence, wind speed distribution, power, especially fatigue damage under this control. Simulation tool FAST.Farm is used to model and analyze wind farms, obtain the variation details of wake and provide simulation data for calculating power and fatigue load. The pitch control brings bias to the CYMP optimization results was neglected, the case studies show that the method of CYMP can reduce the fatigue load by 10.29% and increase the total power by 1.7% compared with only wake steering. The Model Predictive Control collaborative method based on CYMP is proposed, which can increase power by more than 2% and reduce thrust by more than 4% under 10m/s turbulent wind.

Using graph theory, computer aided motion, static force and power flow analysis of planetary gear mechanism is realized. The motion, static force and efficiency calculations of 6HP26 automatic transmission are carried out. Based on kinematic and static force analysis model, related matrices are acquired. Hence, kinematic and static force analysis of planetary gear mechanism is achieved. The link power can be determined by the link speed and torque. Power flow diagrams of each gear are acquired. The efficiency is calculated by transmission ratio method.

A practical method is presented to estimate rare earth elements (REE) concentrations in magmatic vapour phase (MVP) in equilibrium with water-saturated granitic melts based on empirical fluid-melt partition coefficients of REE (k_P^REE). The values of k_P^REEcan be calculated from a set of new polynomial equations linking to the chlorine molality (m_Cl^v) of the MVP associated with granitic melts, which are established via a statistical analysis on the existing experimental dataset. These equations may be applied to the entire pressure range (0.1 to 10.0 kb) within the continental crust, suggesting that light REEs behave differently in magmatic fluids, i.e. either being fluid compatible with higher m_Cl^v or fluid incompatible with lower m_Cl^v values. In contrast, heavy REEs are exclusively fluid incompatible and partition favourably into granitic melts. Consequently, magmatic fluids tend to be rich in LREE relative to HREE, leading to REE fractionation during the evolution of magmatic hydrothermal systems. Maximum k_P^REEvalue for each element is predicted and presented in a REE distribution diagram constrained by the threshold of m_Cl^v. REE contents of the granitic melt is approximated by whole-rock analysis, so that REE concentrations in the associated MVP would be estimated from the value of k_P^REE given chemical equilibrium retains. Two examples are provided respectively, to show the use of this method as a REE tracer to fingerprint the source of ore-fluids responsible for the Lake George intrusion-related Au-Sb deposit in New Brunswick (Canada), and for the Bakircay Cu-Au (-Mo) porphyry systems in northern Turkey.

A variety of myricetin derivatives bearing ferulic acid amide scaffolds were designed and synthesized. The structures of all title compounds were determined by 1 H NMR, 13 C NMR, 19 F NMR and HRMS. Preliminary bioassays suggested that some of the target compounds exhibited remarkable antiviral activities. In particular, compound 4l possessed significant protection activity against tobacco mosaic virus (TMV), with an half maximal effective concentration (EC50) value of 196.11 μg/mL, which was better than commercial agent ningnamycin (447.92 μg/mL). Meanwhile, microscale thermophoresis (MST) indicated that compound 4l have strong binding capability to tobacco mosaic virus coat protein (TMV-CP) with dissociation constant (Kd) values of 0.34 μmol/L, which was better than ningnamycin (0.52 μmol/L). These results suggest that novel myricetin derivatives bearing ferulic acid amide scaffolds may be considered as an activator for antiviral agents.

In the study of rough sets, there are many covering approximation spaces, how to classify covering approximation spaces has become a hot issue. In this paper, we propose concepts covering approximation $T_{1}$-space, $F-$symmtry, covering rough continuous mapping, covering rough homeomorphism mapping to solve this question. We also propose a new method for constructing topology in Theorem 5.1, and get the following properties: (1) For each $x\in U$, $\{X_{i}:i\in I\}\subseteq \mathcal{P}(U)$ is all the subsets of $U$ which contains $x$ and $*$ is a reflexive relation on $U$. If $V\in \tau$ is a subset of $U$ and $x\in V$, then $\underline{*}(\bigcap \limits_{i\in I}X_{i})$ is the smallest subset of $U$ and $x \in \underline{*}(\bigcap \limits_{i\in I}X_{i})\subseteq V$. Denoted by $C(x)=\bigcap \{\underline{*}(X_{i}):x\in \underline{*}(X_{i}),i\in I\}$. (2)If $V\in \tau$ is a subset of $U$, then $V =$ $\bigcup \limits_{x\in V} C(x)$. (3) Let $\{\underline{*}(X_{i}):x\notin \underline{*}(X_{i}), i\in I\}$, then $\overline{\{x\}}$ $=$ $U \setminus \bigcup \limits_{x\notin \underline{*}(X_{i}), i\in I}\underline{*}(X_{i})$; (4) Let $*$ be a reflexive relation on $U$. For every $X\subseteq U$, we have $int(\underline{*}(X))=\underline{*}(X)$. Where $int(\underline{*}(X))$ represents the interior of $\underline{*}(X)$. (5) Let $\{\underline{*}(X_{i}):x\in \underline{*}(X_{i}),i\in I\}$ be a family subsets of $U$, then $\{\underline{*}(X_{i}):x\in \underline{*}(X_{i}),i\in I\}$ is a base for $(U,\tau)$ at the point $x$. \\

In this work, the Ni/Ti/Nb multilayer composite was successfully manufactured by accumulative pack-roll bonding. The microstructure evolution and mechanical properties of the composite during the accumulative roll bonding (ARB) process were investigated by scanning electron microscopy(SEM), energy dispersive spectrometer(EDS), transmission electron microscopy (TEM), micro-hardness and tensile tests. The results showed that after 5 passes of the ARB process, the deformations of layers were relatively uniform, and no large number of interlayer fractures occurred. The microstructures of Ni and Ti were both equiaxed grains with a grain size of 200 nm and 150 nm, respectively, and finer equiaxed grains of the Ni layer were observed at the interface. The laminar structure of Nb layer was observed. The tensile strength and micro-hardness increased significantly as the number of ARB increased. After 5 passes of the ARB process, the tensile strength of the composite reached 792.3 MPa, and the micro-hardness of Ni, Ti, and Nb were increased to 270.2, 307.4, and 243.4 HV, respectively.

With the integrated development of the Internet, wireless sensor technology, cloud computing, and mobile Internet, there has been a lot of attention given to research about and applications of the Internet of Things. A Wireless Sensor Network (WSN) is one of the important information technologies in the Internet of Things; it integrates multi-technology to detect and gather information in a network environment by mutual cooperation, using a variety of methods to process and analyze data, implement awareness, and perform tests. This paper mainly researches the localization algorithm of sensor nodes in a wireless sensor network. Firstly, a multi-granularity region partition is proposed to divide the location region. In the range-based method, the RSSI (Received Signal Strength indicator, RSSI) is used to estimate distance. The optimal RSSI value is computed by the Gaussian fitting method. Furthermore, a Voronoi diagram is characterized by the use of dividing region. Rach anchor node is regarded as the center of each region; the whole position region is divided into several regions and the sub-region of neighboring nodes is combined into triangles while the unknown node is locked in the ultimate area. Secondly, the multi-granularity regional division and Lagrange multiplier method are used to calculate the final coordinates. Because nodes are influenced by many factors in the practical application, two kinds of positioning methods are designed: the unknown node is in the positioning unit or not. When the unknown node is on the side of the positioning unit, we use the method of vector similarity. Moreover, we use the centroid algorithm to calculate the ultimate coordinates of unknown node. When the unknown node is not on the side of the positioning unit, we establish a Lagrange equation containing the constraint condition to calculate the first coordinates. Furthermore, we use the Taylor expansion formula to correct the coordinates of the unknown node. In addition, this localization method has been validated by establishing the real environment.

3D-mapping-aided (3DMA) global navigation satellite system (GNSS) positioning that improves positioning performance in dense urban areas has been under development in the recent years, but it still faces many challenges. This paper details a new algorithm that explores the potential of using building boundary for positioning. Rather than applying complex simulations to analyze and correct signal reflections by buildings, the approach utilizes a convolutional neural network to differentiate between the sky and building in a sky-pointing fisheye image. A new skymask matching algorithm is then proposed to match the segmented fisheye images with skymasks generated from a 3D building model. Each matched skymask holds a latitude and longitude coordinate to determine the precise location of the fisheye image. The results are then compared with the conventional GNSS and advanced 3DMA GNSS positioning methods. The aims of the proposed algorithm are to increase positioning and heading accuracy in a rich urban environment.

In this study, a simple, easy and convenient fluorescent sensing system for detection of vascular endothelial growth factor (VEGF) based on VEGF aptamers, aptamer-complementary fluorescence-labeled probe and streptavidin magnetic beads was developed in only one single tube. The VEGF is the most important biomarker in cancer angiogenesis, and is investigated that serum VEGF level was various according to the different type and course of cancers. Hence, efficient quantification of VEGF is able to improve the accuracy of cancer diagnosis and precision of disease surveillance. In this research, the VEGF aptamer was designed to be able to bind with the VEGF by forming G-quadruplex secondary structures, and then the magnetic beads would capture the none-binding aptamers due to none steric interference, and finally, the fluorescence-labeled probes were hybridized with the aptamers captured by the magnetic beads. Therefore, the fluorescent intensity in the supernatant would specifically reflect the present of VEGF. After an overall optimization, the optimal conditions for detection of VEGF were as followed, KCl, 50 μM; pH 7.0; aptamer, 0.1 μM and magnetic beads, 10 μL (4 μg/μL). The VEGF could be well quantified within a range of 0.2-2.0 ng/ml in plasma, and the calibration curve possessed a good linearity (y = 1.0391x + 0.5471, r = 0.998). The detection limit (LOD) was calculated to be 0.0445 ng/mL according to the formula (LOD = 3.3×σ/S). The specificity of this method was also investigated under the appearance of many other serum proteins, and the data showed the good specificity in this aptasensor-based magnetic sensing system. This strategy provided a simple, sensitive and selective biosensing platform for detection of serum VEGF. Finally, it was expected that this detection technique can be promoted to more clinical applications.

Pyrethroid pesticides (PYRs) as the third most widely used pesticides, following organophosphorus and carbamate pesticides, which are of significant importance in the analysis and detection of vegetables. However, the current pretreatment technology for PYRs confronts challenges of difficult separation and low enrichment efficiency, resulting in a cumbersome and time-consuming pretreatment process with poor selectivity. Here, a simple and efficient magnetic solid-phase extraction (MSPE) strategy was developed to simultaneously purify and enrich five PYRs in vegetables, with the magnetic covalent organic framework nanomaterial COF-SiO2@Fe3O4 as an adsorbent. The COF-SiO2@Fe3O4 was prepared by a simple solvothermal conditions method, using Fe3O4 as magnetic core, benzidine and 3,3,5,5-tetraaldehyde biphenyl as two building units. COF-SiO2@Fe3O4 could effectively capture the targeted PYRs by virtue of its abundant π-electron system and hydroxyl groups. The impact of various experimental parameters on extraction efficiency was investigated to optimize the MSPE conditions, including adsorbent amount, extraction time, elution solvent type and elution time. Subsequently, method validation was conducted under the optimal conditions in conjunction with gas chromatography-mass spectrometry (GC-MS). Within the range of 5.00–100 μg·kg-1 (1.00–100 μg·kg-1 for bifenthrin and 2.5–100 μg·kg-1 for fenpropathrin), the five PYRs exhibited a strong linear relationship, with determination coefficients ranging from 0.9990 to 0.9997. The limits of detection (LODs) were 0.3–1.5 μg·kg-1, and the limits of quantification (LOQs) were 0.9–4.5 μg·kg-1. The recoveries were 80.2–116.7% with relative standard deviations (RSDs) below 7.0%. Finally, COF-SiO2@Fe3O4, NH2-SiO2@Fe3O4 and Fe3O4 were compared as MSPE adsorbents for PYRs. The results indicated that COF-SiO2@Fe3O4 was an efficient and rapid selective adsorbent for PYRs. This method holds promising prospects for the determination of PYRs in real samples.

In this study, a composite flame retardant was created by combining fish scale (FS), fishery waste, and ammonium polyphosphate (APP), a commercially available flame retardant. The composite flame retardant was added to epoxy resin (EP) to form an EP/APP/FS composite that prevents burns and is environmentally friendly. The use of FS conforms to the concept of circular economy and lowers costs by reducing the consumption of APP. Thermogravimetric analysis (TGA), integral procedural decomposition temperature (IPDT), pyrolysis kinetics, limiting oxygen index (LOI), the Underwriters Laboratories 94 (UL94) flammability test, scanning election microscopy, Raman spectroscopy, and energy-dispersive X-ray spectroscopy were used to determine the thermal properties, flame retardant properties, flame retardant mechanism, char morphology, and composition of the composites. The TGA results indicated that the addition of 40% flame retardant raised the char residue from 16.45 wt% (pure EP) to 36.07 wt%, IPDT from 685.6 °C (pure EP) to 1143.1°C, LOI from 21% (pure EP) to 30%, and UL94 classification from fail (pure EP) to V-0. These results suggest an increase in char residue, which indicates better protection of the polymer matrix material. The improvements in IPDT, LOI, and UL94 classification, which indicate greater thermal stability, lower flammability (from flammable to fireproof), and higher flammability rating (from fail to V-0), respectively, suggest that the composite material has favorable thermal properties and is less inflammable.

GABAA receptors are channel proteins crucial to mediating neuronal balance in the CNS. The structure of GABAA receptors allows for multiple binding sites and is key to drug development. Yet, the formation mechanism of the receptor’s distinctive pentameric structure is still unknown. This study aims to investigate the role of three predominant subunits of the human GABAA receptor in the formation of protein pentamers. Through purifying and refolding the protein fragments of the GABAA receptor α1, β2, and γ2 subunits, homopentamers were visualised with negative staining and Cryo-EM. To aid the analysis, AlphaFold2 was used to compare the structures. Results show that α1 and β2 subunit fragments successfully formed homo-oligomers, particularly homopentameric structures, while the predominant heteropentameric GABAA receptor was also replicated through the combination of the three subunits. However, it is still unclear whether γ2 subunits can form homopentamers or their main purpose is to bring together the α1 and β2 subunits to form GABAA receptors. Nevertheless, this study will lead to a deeper understanding of the atomic structure of GABAA receptors, especially in the formation mechanism of complex protein structures, and hopefully pave the way to the development of novel therapeutics for neuropsychiatric diseases.

Abstract Introduction: Visual perceptual skills are essential for independent participation in self-care tasks, educational, work and leisure time activities. The effect of HIV on the visual perceptual skills is not well understood among children in low resource settings like Zimbabwe. Methods: A cross sectional comparative study was done with 30 children living with HIV and 30 children living without HIV residing in Harare urban area. The TVPS-3 was used to assess their visual perceptual skills. SPSS version 22, STATISTICA 13 and Microsoft 2016 were used for data analysis. Results: Both groups of children had mean percentile ranks below 50 on their TVPS-3 scores. Children without HIV generally performed better than those with HIV but the difference was not statistically significant in most cases. Through univariate analysis, only performance on Spatial Relations significantly differed between the two groups. Both groups had lowest scores in Basic visual perceptual skills. Age and school grade were the independent predictors of the children’s performances in the study. Conclusion: There is need for Occupational therapy services in public primary schools and in the pediatric Opportunistic Infections clinics in hospitals to be part of the health team which caters for children with visual perceptual challenges.

Neonicotinoids (NEOs) have become the most widely used insecticides in the world since the mid-1990s. According to Chinese dietary habits, rice and water are usually heated before being consumed, but the information about the alteration through the heat treatment process is very limited. In this study, the parents of NEOs (p-NEOs) accounted for >99% of the total NEOs mass (∑NEOs) in both uncooked (median: 66.8 ng/g) and cooked (median: 41.4 ng/g) rice samples from Guangdong Province, China, while the metabolites of NEOs (m-NEOs) involved in this study accounted for less than 1%. We aimed to reveal the concentration changes of NEOs through heat treatment process, thus, several groups of rice and water samples from Guangdong were cooked and boiled, respectively. Significant (p < 0.05) reductions in acetamiprid, imidacloprid (IMI), thiacloprid, and thiamethoxam (THM) have been observed after the heat treatment of the rice samples. In water samples, the concentrations of THM and dinotefuran decreased significantly (p < 0.05) after the heat treatment. These results indicate the degradation of p-NEOs and m-NEOs during the heat treatment process. However, the concentrations of IMI increased significantly in tap water samples (p < 0.05) after heat treatment process, which might be caused by the potential IMI precursors in those industrial pesticide products. The concentrations of NEOs in rice and water can be shifted by the heat treatment process, so this process should be considered in relevant human exposure studies.

FY-3E WindRAD (Fengyun-3E Wind Radar) is a dual-frequency rotating fan-beam scatterometer. Its data characteristics, NOC (NWP Ocean Calibration), and wind retrieval performance are investigated in this paper. The radar view geometry diversity varies across the swath, with maximum diversity in the sweet swaths and limited diversity in the outer and nadir swaths. When NOC backscatter calibration coefficients are computed as a function of incidence angle only (NOCint), a smooth correction is found. However, when relative antenna azimuth angle is included (NOCant), it appears that the corrections as a function of relative azimuth angle vary harmonically and substantially for a specific incidence angle. NOCant corrections yield a better fit of the measurements to the GMF (Geophysical Model Function). Hence NOCant is applied for the wind retrieval analysis from Ku-band, C-band. An extra engineering correction of 0.15dB and 0.2dB is applied on Ku-band and C-band backscatter values, respectively, to reduce the wind speed bias without increasing the standard deviation. Overall, NOCant is the best option for both channels. Also, the instrument backscatter data stability over time is good and the retrieved winds can fulfill operational requirements.

Uridine diphosphate (UDP)-glycosyltransferases (UGTs) are major phase II detoxification enzymes involved in glycosylation of lipophilic endobiotics and xenobiotics, including phytoalexins. Nicotine, one of the most abundant secondary plant metabolites, is highly toxic to herbivorous insects. Plant-herbivore competition has been the major impetus for evolution of large superfamilies of UGTs and other detoxification enzymes. However, UGT functions in Myzus persicae adaptation have remained unknown. In this study, UGT inhibitors (sulfinpyrazone and 5-nitrouracil) significantly increased nicotine toxicity in M. persicae nicotianae, suggesting UGTs may be involved in nicotine tolerance. One hundred one UGT transcripts identified from the M. persicae genome/transcriptome were renamed according to UGT Nomenclature Committee guidelines and clustered into 11 families: UGT329, UGT330, UGT339, UGT341-UGT345, and UGT348-UGT350. UGT344 contained the most UGTs (fifty-seven). Ten UGTs (UGT330A3, UGT339A2, UGT341A6, UGT342B3, UGT343C3, UGT344D5, UGT344D8, UGT348A3, UGT349A3 and UGT350A3) were overexpressed in M. persicae nicotianae compared with M. persicae sensu stricto. UGT330A3/UGT344D5/UGT348A3/UGT349A3 knockdown significantly increased M. persicae nicotianae nicotine sensitivity, suggesting UGT upregulation in this subspecies may be associated with nicotine tolerance and thus host adaptation. This study reveals possible UGTs relevant to nicotine adaptation in tobacco-consuming M. persicae nicotianae and might facilitate further validation of the roles of these UGTs in nicotine tolerance.

With a high proportion of distributed photovoltaic and lower fossil energy integrated into the distribution network, it is very difficult to ensure the reliability of power supply. The distributed photovoltaic planning model based on big data is proposed. According to the impact stochastic photovoltaics and loads on reliability planning, the static and dynamic capacity-load ratios are proposed. The big data analysis model of distributed photovoltaic planning is established. The big data multi-scenario generation and reduction algorithm of stochastic distributed photovoltaic and load planning is studied, and a source-load big data scenario matching model is proposed. Ac-cording to the source load big data scenario, the dynamic capacity-load ratio of the distribution network is obtained. The static capacity-load ratio calculation method in distribution network planning is studied to ensure the reliability of power supply. Finally, the IEEE 33-bus system is used as an example. The results show that distributed photovoltaic planning based on big data and multi-scenario methods can improve photovoltaic utilization and power supply reliability.

In the process of deflagration of energetic materials, strong electromagnetic radiation is to be generated, which causes the surrounding electronic equipment to fail to work normally. To solve this problem, it is necessary to clarify the mechanism of electromagnetic radiation generated by energetic materials. The mechanism of plasma changed by the deflagration of energetic materials is an important topic in the aerospace and geophysics fields. The academic community holds two main viewpoints on the mechanism of electromagnetic radiation generated by energetic materials: one is that the solid material is squeezed and deformed during the deflagration of energetic materials, and the charges of different polarities rub in space to form effective electric dipoles, which eventually generate electromagnetic radiation. Another view is that the deflagration of energetic materials causes the temperature of the medium to rise sharply, and bremsstrahlung is formed during the compression and diffusion of the high-temperature wave front, resulting in the generation of electromagnetic radiation. This paper, based on theoretical analysis and experimental data, holds the view that electromagnetic radiation is generated by the high-temperature thermal effect. It studies the relationship between temperature and electromagnetic radiation and obtains quantitative analysis conclusions.

During the explosion of energetic materials, obvious electromagnetic interference will be generated, which will affect the normal operation of surrounding electronic equipment. Experiments are still an important means to study this issue. A set of electromagnetic radiation measurement device based on short-wave omnidirectional antenna and ultra-wideband omnidirectional antenna is designed to measure the electromagnetic radiation generated by the explosion of energetic materials of different masses, and the electromagnetic radiation characteristics are obtained through data processing. The results show that the mass of the energetic material has a significant effect on the time-domain characteristics of the electromagnetic radiation generated by the explosion: the higher the mass of the energetic material, the shorter the delay response of the electromagnetic signal, the longer the duration, and the earlier the peak appears. The frequency of electromagnetic radiation signals generated by the explosion of energetic materials is mainly concentrated below 100 MHz, and the energy is most concentrated in the frequency band of 0~50 MHz. The composition of energetic materials has the greatest influence on the spectral distribution, and the spectral distribution of electromagnetic radiation produced by the explosion of explosives with different compositions has obvious specificity. The electromagnetic radiation intensity generated by the explosion of energetic materials has a strong correlation with the distance from the explosion center, and it decreases with the increase of the distance, and the decreasing range is large. The structure and detonation method of energetic materials can change the geometrical motion mode during the explosion, resulting in the non-uniformity of electromagnetic radiation propagation.

Finding the key factor and possible "Newton's laws" in financial markets has remained the central issue in this area. However, with the development of information and communication technologies, financial models are becoming more and more realistic but complex which is contradictory to the objective law “Greatest truths are the simplest”. Therefore, this paper attempts to discover the most critical parameter and establishes an evolutionary model which is independent of micro features. In the model, information is the only key factor and stock price is the emergence of the collective behavior. The statistical properties of the model are significantly similar to the real market. It also explains the correlations of stocks within an industry, which provide a new idea for the study of key factors and core structures in the financial market.

The Pythagorean fuzzy set (PFS), which is characterized by a membership and a non-membership degree and the square sum of them is less or equal to one, can act as an effective tool to express decision makers’ fuzziness and uncertainty. Considering that the Heronian mean (HM) is a powerful aggregation operator which can take the interrelationship between any two arguments, we study the HM in Pythagorean fuzzy environment and propose new operators for aggregating interval-valued Pythagorean fuzzy information. First, we investigate the HM and geometric HM (GHM) under interval-valued intuitionistic fuzzy environment and develop a series of aggregation operators for interval-valued intuitionistic fuzzy numbers (IVIFNs) including interval-valued intuitionistic fuzzy Heronian mean (IVIFHM), interval-valued intuitionistic fuzzy geometric Heronian mean (IVIFGHM), interval-valued intuitionistic fuzzy weighted Heronian mean (IVIFWHM) and interval-valued intuitionistic fuzzy weighted geometric Heronian mean (IVIFWGHM). Second, some desirable and important properties of these aggregation operators are discussed. Third, based on these aggregation operators, a novel approach to multi-attribute decision making (MADM) is proposed. Finally, to demonstrate the validity of the approach, a numerical example is provided and discussed. Moreover, we discuss several real-world applications of these operators within policy-making contexts.

A composite flocculant P(AM–DMDAAC) was synthesized by the copolymerization of acrylamide (AM) and dimethyl diallyl ammonium chloride (DMDAAC). Using microwave (MV) assistance with ammonium persulfate as initiator, the synthesis provided short reaction time and better solubility product. Nuclear magnetic resonance spectroscopy (1H NMR and 13C NMR), Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and differential thermal analysis-thermo gravimetric analyzer (DTA-TGA) were used to determine the structure and morphology of P(AM–DMDAAC). Parameters affecting the intrinsic viscosity ([η]) of P(AM–DMDAAC), such as microwave time, mass ratio of DMDAAC to AM, initiator ammonium persulfatedosage, sodium benzoate dosage, bath time, reaction temperature and pH value were examined. Results showed that the optimum synthesis conditions were microwave time 1.5 min, m(DMDAAC): m(AM) is 4:16, 0.5 wt‰ initiator, 0.4 wt‰ EDTA, 0.3 wt‰ sodium benzoate, 2 wt‰ urea, 4 h bath time, 4.0h reaction time and pH 2. To study the removal of phenol by P(AM–DMDAAC), the influence of flocculant dose, pH value and the stirring speed were investigated, with optimization providing 99.8 % removal.

This paper initiates the study of the mathematical aspects of the ad-hoc Lanzhou index. If G is a graph with the vertex set {x1,⋯,xn}, then the ad-hoc Lanzhou index of G is defined by Lz¯(G)=∑i=1ndi(n−1−di)2, where di represents the degree of the vertex xi. Several identities for the ad-hoc Lanzhou index, involving some existing topological indices are established. The problems of finding graphs with the extremum values of the ad-hoc Lanzhou index from the following sets of graphs are also attacked: (i) set of all connected ξ-cyclic graphs of a fixed order, (ii) set of all connected molecular ξ-cyclic graphs of a fixed order, (iii) set of all graphs of a fixed order, (iv) set of all connected molecular graphs of a fixed order.

In this paper, we propose a new covering-based set in which the lower and the upper approximation operations are defined by neighborhood systems. We discuss this new type of covering-based set systematically in two steps. First, we study the basic properties of this covering-based set, such as the properties of normality, contraction, and monotone. Second, we discuss the relationship between the new type of covering-based set and the other ten sets proposed.

In this paper, we propose a new covering-based set in which the lower and the upper approximation operation are defined by neighborhood systems. We discuss this new type of covering-based set systematically in two steps. First, we study the basic properties of this covering-based set, such as the properties of normality, contraction, and monotone. Second, we discuss the relationship between the new type of covering-based set and the other ten sets proposed.

Aiming to diminish the defects caused by high-speed pulsed GMAW welding, such as non-penetration, non-fusion, humping and undercut, the paper proposed an improved twin-wire double-pulsed high-speed welding process by introducing the impact of additional shielding gas on the welding pool and the effects of different shielding gas flowrates on the microstructure and mechanical properties of the welded seam was investigated. The 2205 duplex stainless steel plate was used as the base material for the butt welding test, and the welded seams were subjected to tensile test, metallographic analysis, hardness analysis, and nondestructive testing. The results indicate that as the flowrate of additional shielding gas increases in the range of 8 L/min~16 L/min, the width of the welded seam increases and the height of reinforcement decreases gradually. However, a grooved seam with a lower middle region and higher sides will appear when the gas flowrate becomes excessively large. The test results indicate that the jet impact force is relatively moderate when the flowrate of the additional shielding gas is 12 L/min and thus, is optimal for the welded seam.

In the neuroscience research field, specific for medical imaging analysis, how to mining more latent medical information from big medical data is significant for us to find the solution of diseases. In this review, we focus on neuroimaging data that is functional Magnetic Resonance Imaging (fMRI) which non-invasive techniques, it already becomes popular tools in the clinical neuroscience and functional cognitive science research. After we get fMRI data, we actually have various software and computer programming that including open source and commercial, it's very hard to choose the best software to analyze data. What's worse, it would cause final result imbalance and unstable when we combine more than software together, so that's why we want to make a pipeline to analyze data. On the other hand, with the growing of machine learning, Python has already become one of very hot and popular computer programming. In addition, it is an open source and dynamic computer programming, the communities, libraries and contributors fast increase in the recent year. Through this review, we hope that can make neuroimaging data analysis more easy, stable and uniform base the one platform system.

This study reports multivariate statistical techniques applied including cluster analysis to evaluate and classify the river pollution level in Taiwan, and principal component analysis-multiple linear regression (PCA-MLR) to identify the possible pollution source. Water quality and heavy metal monitoring data from Taiwan Environmental Protection Administration (EPA) was evaluated for 14 rivers in the four regions of Taiwan. The Erren River was classified as the most polluted River in Taiwan. Biochemical oxygen demand, ammonia, and total phosphate concentration in this river were the highest of the 14 rivers evaluated. In addition, heavy metal levels of the following rivers exceeded the Taiwan EPA standard limit: lead - in the Dongshan, Jhuoshuei, and Xinhuwei Rivers; copper - in the Dahan, Laojie, and Erren Rivers; and manganese - in all rivers. Water pollution in the Erren River was estimated to originate 72% from industrial sources, 16% from domestic black water, and 12% from natural sources and runoff from other tributaries. Our research showed that PCA-MLR and the cluster analysis model accomplished our study objectives and will be helpful tools to evaluate water quality in rivers and we suggest that the continuous monitoring should be conducted to monitor water pollution from anthropogenic activities.

Optical network monitoring and soft failure identification such as optical filter shifting and filter tightening is increasingly significant in the future complex and dynamic optical networks. Center frequency shift of optical filtering device in optical network has a serious impact on the perfor-mance of multi-span transmission, especially in high spectrum efficiency faster-than-Nyquist (FTN) transmission systems with various optical switching and add/drop nodes. Existing moni-toring schemes generally have problem of high cost, high complexity and the inability to realize multi-channel online monitoring, which makes it difficult to be applied in wavelength division multiplexing (WDM) system with numerous nodes. In this paper, a monitoring scheme of fre-quency shift of optical filtering devices based on optical label (OL) is proposed and demonstrated. The signal spectrum of each channel is intentionally divided into many sub-bands with corre-sponding optical labels loading. The characters of spectrum power changing caused by frequency shift can be reflected on labels power changing of each sub-band, which are used to monitor and estimate the value of frequency shift by DSP algorithm. Simulation results shows that the that the monitoring errors of frequency shift can be kept below 0.5GHz reasonably after 10-span WDM transmission in FTN polarization multiplexing m-ary quadrature amplitude modulation (PM-mQAM) systems. In addition, 250km fiber transmission experiments are also carried out and the similar results are obtained, which further verify the feasibility of our proposed scheme. The characters of low cost, high reliability and efficiency make it a better candidate for practical ap-plication in the future FTN WDM networks.

By constructing a static map, the library robot can navigate and access documents autonomously, which greatly improves efficiency; however, for libraries where shelves can be moved, map changes do not allow for direct navigation, and also sensors such as radar and camera are relatively expensive, so we propose a low-cost navigation algorithm based on real-time ranging data and map matrices, and designed a mobile archive access robot. In order to obtain real-time distance data, nine near/long range sensors were mounted on the chassis and a composite digital filtering algorithm was designed based on different moving area characteristics; then the access task matrix and map matrix were designed based on the archive access task and the location characteristics of the archive shelf placement, the robot can rely on the range data to update the map matrix during the moving process, complete its own positioning, and use the task matrix The robot can use the task matrix to complete autonomous navigation and access to multiple files. Experiments show that the filtered positioning accuracy can reach 1cm, while the robot can move to the target shelf autonomously, which is more practical and less costly.

Micro/Nano Robot is an intelligent and efficient microrobot that can perform specific tasks under the influence of external stimuli. Depending on the application scenarios, the microrobot can adaptively transform into appropriate functional forms under different external stimuli, thus perfectly matching the needs. To date, microbots have been widely used in targeted therapy, drug delivery, tissue engineering, environmental remediation, and other fields. Although the applications of microrobots are promising, there are only a few reviews that can focus on the preparation methods and driving mechanisms. Therefore, it is necessary to outline the current status of the development of these microrobots in order to provide some new insights for the further development of the field. Therefore, this paper reviews the research progress of microrobots in terms of preparation methods, stimulus response mechanisms and applications, and highlights the applicability of different preparation methods and stimulus types. Finally, the current challenges faced by microrobots are highlighted and possible solutions are proposed to facilitate the practical application of microrobots.

Water resource is considered as a significant factor in development of regional environment and society. Water consumption prediction can provide important decision basis for the regional water supply scheduling optimisations. According to the periodicity and randomness nature of the daily water consumption data, a Markov modified autoregressive moving average (ARIMA) model is proposed in this study. The proposed model, combined with the Markov chain, can correct the prediction error, reduce the continuous superposition of prediction error, and improve the prediction accuracy of future daily water consumption data. The daily water consumption data of different monitoring points are used to verify the effectiveness of the model, and the future water consumption is predicted, in the study area. The results show that the proposed algorithm can effectively reduce the prediction error compared to the ARIMA.

A novel metal-doped carbon quantum dot, zinc-chlorine co-doped carbon quantum dots (Zn/Cl-CQDs), has been developed for the fluorescent probe detection of vitamin B2 and the analysis of the correlation properties of this carbon quantum dot and vitamin B2. Stability experiments demonstrate that Zn/Cl-CQDs possess good fluorescence properties under alkaline conditions. However, when vitamin B2 is added into Zn/Cl-CQDs, the fluorescence intensity decreases sharply, indicating that a fluorescence quenching phenomenon occurs between vitamin B2 and Zn/Cl-CQDs. Lastly, the use of Zn/Cl-CQDs in the detection of vitamin B2 tablets and vitamin B2-rich fruits resulted in recovery rates of 98.2% and 100.6%, respectively. Therefore, this method can be well applied to the detection and analysis of vitamin B2, and has great development prospects in the pharmaceutical industry and food monitoring fields.

In this study, a monoethanolamine aerosol growth model was developed to investigate the aerosol growth factor. Interactions among the internal conditions in an absorber were considered in this aerosol model. Additionally, an experiment was conducted to measure aerosol particle size, for collecting in-house validation data. Sucrose was used as the aerosol nuclei instead of sulfuric acid to prevent the corrosion of equipment used in the experiment. Experimental results showed that the outlet aerosol sizes increased to the same size regardless of the sucrose concentrations. The aerosol growth model was validated using the in-house experimental data. The aerosol growth model efficiently predicted the aerosol size. For investigating aerosol growth effects, particle number concentration was determined to be the primary factor affecting aerosol growth and amine emissions. When the particle number concentration increased, the aerosol size decreased, whereas the MEA emission increased.

Nitrile butadiene rubber (NBR) and its various composites are extensively studied as matrix materials for oil-free lubricated mechanical friction surfaces. While numerous macroscopic friction experiments can compare the frictional performance of different NBR composites, the complex material preparation and low experimental efficiency pose challenges. Nanoscale molecular dynamics (MD) simulations can help develop materials with improved friction properties, but they cannot directly provide the friction coefficients of actual macroscopic friction surfaces. Therefore, it is important to integrate the advantages of macroscopic and nanoscale friction studies and perform a synergistic analysis to modify the friction properties of composite materials. In this study, a multi-scale approach is proposed to simulate the frictional characteristics of carbon nanotube (CNT)-reinforced NBR by combining the MD friction simulation， micromechanical bridging model, and macroscopic finite element analysis (FEA) methods. The results of the multi-scale friction simulation of copper (Cu)-CNT/NBR composites show that the addition of CNTs significantly improves the frictional properties of NBR, and the extent of the improvement is related to the mass fraction of CNTs. As the mass fraction of CNTs increases (0%, 1.25%, 2.5%, 5%), the coefficient of friction decreases from 0.50 to 0.38. The results are validated by ring-block friction experiments at the same scale as the simulations.

For Convolutional Neural Network (CNN), Depthwise Separable CNN (DSCNN) is a preferred architecture for Application Specific Integrated Circuit (ASIC) implementation on edge devices. It can benefit from a multi-mode approximate multiplier proposed in this work. The proposed approximate multiplier uses two 4-bit multiplication operations to implement a 12-bit multiplication operation by reusing the same multiplier array. With this approximate multiplier, sequential multiplication operations are pipelined in a modified DSCNN to fully utilize the PE array in the convolutional layer. This Approximate (A-DSCNN) was implemented on TSMC 40-nm CMOS process with a supply voltage of 0.9 V. At the clock frequency of 200 MHz, the design achieves 4.78 GOPs/mW while occupying 1.24 mm x 1.24 mm silicon area. Compared to conventional DSCNN implemented in a similar process node, the chip area and power consumption were reduced by 53% and 25%, while the throughput was improved by 17%.

Robotic systems have been widely used in various industries, so the security of communication between robots and their components has become an issue that needs to be focused on. As a framework for developing robotic systems, the security of ROS2 can directly affect the security of the upper-level robotic systems. Therefore, it is a worthwhile research topic to detect and analyze the security of ROS2. In this paper, we adopt a formal approach to analyze the security of the communication mechanism of ROS2. First, we use a state transition system to model the potential vulnerabilities of ROS2 based on the ROS2 communication mechanism and the basic process of penetration testing. Secondly, we introduce the CIA model on the basis of the established vulnerability model and use LTL to define its security properties. Then, we design and implement a vulnerability detection tool for ROS2 applications based on the vulnerability model and security properties. Finally, we experimentally test some ROS2-based applications, and the results show that ROS2 has vulnerabilities without additional protection safeguards.

Background: Young adults, particularly university students might be at greater risk of developing psychological distress, and exhibiting symptoms of anxiety and depression during the COVID-19 pandemic. Objective: The primary objective of this study was to explore and compare the determinants and predictors of mental health (anxiety and depression) during and after COVID-19 lockdown among university students. Methods: This was an observational, cross-sectional study with a sample size of 417 students. An online survey utilizing International Physical Activity Questionnaire–Short Form (IPAQ-SF), General Anxiety Disorder–7 (GAD-7) and Patient Health Questionnaire-9 (PHQ-9) was distributed to Universiti Tunku Abdul Rahman students via Google forms. Results: During lockdown, family income [χ² (1, n=124) = 5.155, p=0.023], and physical activity [χ² (1, n=134) = 6.366, p=0.012] were associated with anxiety, while depression was associated with gender [χ² (1, n=75) = 4.655, p=0.031]. After lockdown, family income was found to be associated with both anxiety [χ2 (1, n=111) = 8.089, p=0.004], and depression [χ2 (1, n=115) =9.305, p=0.002]. During lockdown, family income (OR=1.60, p=0.018), and physical activity (OR=0.59, p=0.011) were predictors for anxiety, and gender (OR=0.65, p=0.046) being the only predictor for depression. After lockdown, family income was a predictor for both anxiety (OR=1.67, p=0.011), and depression (OR=1.70, p=0.009). Conclusion: Significant negative effects attributed to the COVID-19 lockdown, and certain factors predisposed to the worsening of mental health status in university students. Family income, physical activity level, and gender were some of the major determinants that influenced the anxiety and depression.

The cross-linkable PCL-PEG analogues block-graft copolymer was designed and synthesized, which with the copolymer of the MEO₂MA and OEGMA as graft chains to improve the mPEG-b-PCL-b-mPEG copolymer the aqueous solution properties. And successfully prepared two hydrogels via a copper-catalyzed 1, 3-dipolar azide-alkyne cycloaddition reaction of alkyne-terminated poly[glycidyl methacrylate-co-2-(2-methoxyethoxy) ethyl methacrylate-co-oligo (ethylene glycol) methacrylate] [P(GMA-co-MEO₂MA-co-OEGMA)] with azide end-functionalized PCL-PEG analogues block-graft copolymer, and tetrakis (2-propynyloxymethyl) -methane (TPOM) and with azide end-functionalized PCL-PEG analogues block-graft copolymer. The copolymer's chemical structure was characterized by proton nuclear magnetic resonance spectroscopy and fourier transform infrared spectroscopy. The molecular weights of the copolymers were decided with gel permeation chromatography. The water solubility and temperature sensitivity of the copolymers were studied by taking digital photos and transmittance change measured by UV spectrophotometer at different temperatures. Fluorescence probes, surface tension, dynamic light scattering and transmission electron microscopy were used to analyze the micelles that copolymers self-assembly in aqueous solution. The sol-gel behavior of copolymer solutions at high concentrations was explored by vial inversion experiments. Finally, the network structure of the gels was observed by scanning electron microscopy. These conclusions indicate that these hydrogels are expected to be used as a new material in the field of biomedicine.

Over the past four decades, China has experienced a nutritional transition and has developed the largest population of internet users. In this study, we evaluated the impacts of internet access on the nutritional intake in Chinese rural residents. An IV-Probit-based propensity score matching method was used to determine the impact of internet access on nutritional intake. The data were collected from 10042 rural households in six Chinese provinces. The results reveal that rural residents with internet access have significantly higher energy, protein, and fat intake than those without. Chinese rural residents with internet access consumed 1.35% (28.62 kcal), 5.02% (2.61 g), and 4.33% (3.30 g) more energy, protein, and fat, respectively. There was heterogeneity as regards the intake of energy, protein, and fat among those in different income groups. Moreover, non-staple food consumption is the main channel through which internet access affects nutritional intake. The results demonstrate that the local population should use the internet to improve their nutritional status. Further studies are required to investigate the impact of internet use on food consumed away from home and micronutrients intake.

Differences in the physical and chemical properties of reclaimed water (RW) and natural surface water (SW) lead to the differences in terms of nitrogen and phosphorus release when pipeline sediments enter these water bodies. The nitrogen and phosphorus release kinetics from pipe sediments with different particle sizes have been investigated. The results demonstrated that both SW and RW had a pH buffering effect after sediment addition, and the final pH (approximately 8.1) of RW was lower. The release of total phosphorus (TP) and ammonia nitrogen ( NH₄⁺-N) fitted the first-order kinetic model where the release of TP reached equilibrium; TP release was inhibited in both SW and RW, where RW exhibited the lowest (by a factor of 1.23~2.44) release (0.002 mg/g). The release of NH4+-N was promoted in both SW and RW; the maximum release in RW was 0.0188 mg/g. The amounts of NH₄⁺-N released in SW and RW were 1.02-1.40 and 1.30-1.80 times that of the control group (CG), respectively. The percentage of TP and NH₄⁺-N release in the three groups was highest in 75-154 μm pipe sediment, reaching 34.53% and 43.51% in SW and RW, respectively. These results can assist in the development of water quality evolution models for specific urban scenarios, and provide important guidance for the precise regulation of recharge water quality during and after rainfall.

Topology optimization is a pioneering design method that can provide various candidates with high mechanical properties. However, the high-resolution for the optimum structures is highly desired, normally in turn leading to computationally intractable puzzle, especially for the famous Solid Isotropic Material with Penalization (SIMP) method. In this paper, an efficient and high-resolution topology optimization method is proposed based on the Super-Resolution Convolutional Neural Network (SRCNN) technique in the framework of SIMP. The SRCNN includes four processes, i.e. refining, path extraction & representation, non-linear mapping, and reconstruction. The high computational efficiency is achieved by a pooling strategy, which can balance the number of finite element analysis (FEA) and the output mesh in optimization process. To further reduce the high computational cost of 3D topology optimization problems, a combined treatment method using 2D SRCNN is built as another speeding-up strategy. A number of typical examples justify that the high-resolution topology optimization method adopting SRCNN has excellent applicability and high efficiency for 2D and 3D problems with arbitrary boundary conditions, any design domain shape, and varied load.

Geological structures such as joints and faults in rock mass have significant influence on open pit mining. Hence, it is critical to develop a understanding of dynamic joint behaviour under blasting loading. This in turn can provide both theoretical and practical guidance to improve blasting rock fragmentation and associated bucket excavating efficiency. In this paper, delayed blasting on the highwall bench at Baiyunebo open-pit mine was used as an example, a nonlinear joint blasting model was also constructed. By simplifying the blasting wave propagation velocity, the P-wave normal incidence to the joint was obtained. The peak vibration velocity was 0.33m/s at 3.0s. The S-wave reflected by the joint interface was first reflected backward and then forward, which the peak vibration velocity was 0.027 m/s. By combining the relevant stress and displacement theories of type I and II cracks, the equipotential diagrams of the stress and displacement field with the vibration velocity of the particle were obtained. σx was positive in the direction of 0~330° and subjected to tensile stress, whereas σy was positive in the direction of 0~180° and under tensile stress. The longitudinal σy along joint was low in compressive stress distribution area and did not affect surrounding rock at the time. The stress concentration appeared in the lower right corner. Based on the continuous behavior of stress wave in joints, the asymmetry and continuous changes reflected in the whole process could not be analysed by the contour diagram. Hence, ANSYS used to analyse distribution of the stress field. The intensity of the shock wave after detonation was greater than that of the rock strength. Subsequently, the sub-layer shock wave supplemented the shock wave energy that was not enough to break the rock and induced further cracking. This was able to be visualized by the degree of color change post-processing. It was concluded that with the attenuation of the detonation wave energy, the stress exhibited a decreasing trend in this process. According to distribution of the peak effective stress, it was found that the peak value first increased to 10-12 MPa and then showed a downward trend. Overall, the results were validated against the finite element simulation and mathematical analysis.

In high-risk railway construction, personal protective equipment monitoring is critical but challenging due to small and frequently obstructed targets. We propose YOLO-EA, an innovative model that enhances safety measure detection by integrating ECA into its backbone's convolutional layers, improving discernment of minuscule objects like hardhats. YOLO-EA further refines target recognition under occlusion by replacing GIoU with EIoU loss. YOLO-EA's effectiveness was empirically substantiated using a dataset derived from real-world railway construction site surveillance footage. It outperforms YOLOv5, achieving 98.9% precision and 94.7% recall, up 2.5% and 0.5% respectively, while maintaining real-time performance at 70.774 fps. This highly efficient and precise YOLO-EA holds great promise for practical application in intricate construction scenarios, enforcing stringent safety compliance during complex railway construction projects.

Container crane has been widely used for port operation. However, the structure of port container crane is large, which always lead to crane damage under the vibration and strong wind. Therefore, a method for vibration reduction of container crane structure based on particle damping technology is proposed. In this investigation, the scale 1:80 crane model is built, the equivalent mechanical model is also established to preliminary verify the effect of vibration suppression. Furthermore, the dependence of vibration suppression effect on the key parameters of the damper, i.e., filling material, filling rate, particle size, and installation position of dampers are analyzed through experiments. The results indicate that the vibration peak of the crane structure displayed in Simulink oscilloscope is weakened and lags behind, the installation of the damper brings the effect of vibration suppression for the crane, the vibration suppression effect reaches 25%; the crane mode obtains the best vibration suppression effect under the condition that the material filled in the damper has a large density and elastic modulus, sufficient collision space and high collision frequency, and the dampers are installed far away from the crane center of gravity. The optimum parameters of the damper obtained from experiments, 12 mm lead beads, filling rate of 60%, installed in the distal ends within the strength range of the forearm of the crane. It is thus concluded that the particle damping technology has provided an effective way in wind and vibration reduction for container crane.

During the launch and return of a spacecraft, the intense combustion of propellants generates strong electromagnetic radiation, which interferes with the operation of electronic equipment in the spacecraft. To improve the electromagnetic compatibility of electronic equipment in spacecraft, it is necessary to study the electromagnetic radiation characteristics of rocket fuel. An electromagnetic radiation measurement system based on antennas is designed to measure the electromagnetic radiation generated by rocket fuel, and the electromagnetic radiation characteristics are obtained through data analysis. The mechanism of the electromagnetic radiation generated by rocket fuel is comprehensively analysed through the spatial, time-domain, frequency-domain, and energy-domain characteristics. A characterization model is established to provide a reliable scheme for evaluating the influence of rocket fuel electromagnetic radiation on electronic equipment in spacecraft.

The surface enhanced fluorescence（SEF）detection bases by plasmonic nanopillars array with nanoparticles has opened up a new gate in the application of biological imaging and sensing. The fluorescence enhancement of the probe molecule depends on its position in equilibrium, which is close to the hot spot leading to the electromagnetic field enhancement, but not too close to the metal surface resulting in quenching. Here, a large scale SiO₂-Ag-cicada wing SEF substrate was fabricated by magnetron sputtering with correction enhancement factor of 797.6. Thereinto the cicada wing provides the skeleton of the nanopillars array structure, the deposited Ag constructs two kinds of hot spots, and SiO₂ forms a separation layer to prevent quenching. Moreover, the substrate exhibited good reproducibility, high sensitivity with low limits of detection (LOD) and high stability for oxidation resistance. We propose that SEF substrate with modification of SiO₂ can not only improve the enhancement performance, but also expanding its application in the biological investigations.

This study presents an exploration into identifying the interactions between ocean waves and the continental margin in the origination of double-frequency (DF, 0.1-0.5 Hz) microseisms recorded at 33 stations across East Coast of USA (ECUSA) during a ten-day period of ordinary ocean wave climate. Daily primary vibration directions are calculated in three frequency bands and projected as great circles passing through each station. In each band, the great circles from all stations exhibit largest spatial density primarily near the continental slope in the western North Atlantic Ocean. Generation mechanisms of three DF microseism events are explored by comparing temporal and spatial variations of the DF microseisms with the migration patterns of ocean wave fronts in Wavewatch III hindcasts. Correlation analyses are conducted by comparing the frequency compositions of and calculating the correlation coefficients between the DF microseisms and the ocean waves recorded at selected buoys. The observations and analyses lead to a hypothesis that the continental slope causes wave reflection, generating low frequency DF energy and that the continental shelf is where high frequency DF energy is mainly generated in ECUSA. The hypothesis is supported by the primary vibration directions being mainly perpendicular to the strike of the continental slope.

Species data of 249 National Nature Reserves in China was used to identify potential underlying drivers of latitudinal gradients in plant diversity. We used generalized linear models (GLMs) to assess the correlations between predictor and response variables. We also used SAM (Spatial Analysis in Macroecology) to eliminate autocorrelation along each of the 249 studied locations. We used the Akaike information criterion (AICc; Montoya et al. 2007) to select the independent variables were those included in the best models from different combinations of climate, habitat and animal variables. Variance partitioning was used to decompose the variation in plant richness across different taxonomic levels among the three groups of predictors. We found that: Total plant species, gymnosperms, angiosperms and ferns showed significant latitudinal trends in richness (p < 0.001). Water-energy and habitat variables generally explained more variation in richness across different plant groups than did animal richness. Annual precipitation was selected as the best water-energy variable across different taxonomic plants groups, soil PH and elevation range were selected as the best habitat variables across different taxonomic plant groups. The independent effects of habitatvariables were higher than that of water-energy and animal variables across different taxonomic plants groups. Water-energy, habitat heterogeneity, and animal variables explain 48.8% of the variation in total species richness, 28.2% in gymnosperm richness, 44.2% in angiosperm richness, and 38.9% in fern richness.Plants showed significant latitudinal trends in richness (p < 0.001). Water-energy and habitat variables generally explained more variation in richness across different taxonomic plants groups than did animal variables. The independent effects of habitat variables were higher than those of water-energy and animal variables across different taxonomic plants groups.

This study derives space travel pricing by Walrasian Equilibrium, which is logical reasoning from the general relativity theory (GRT), the accounting equation, and economic supply and demand functions. The Cobb-Douglas functions embed the endogenous space factor as new capital to form the space travel firm's production function, which is also transformed into the consumer's utility function. Thus, the market equilibrium occurs at the equivalence of supply and demand functions, like the GRT presents the equivalence between the spatial geometric tensor and the energy-momentum tensor, which explains the principles of gravity and the motion of space matter in the spacetime framework. The mathematical axiomatic set theory of the accounting equation explains the equity premium effect that causes a short-term accounting equation inequality, then reaches the equivalence by suppliers' incremental equity through the closing accounts process of the accounting cycle. On the demand side, the consumption of space travel can be assumed as a value at risk (VaR) investment to attain the specific spacetime curvature in an expected orbit. Spacetime market equilibrium is then achieved to construct the space travel pricing model. The methodology of econophysics and analogy method was applied to infer the space travel pricing by the model of profit maximization, single-minded, and envy-free pricing in unit-demand markets. A case study with simulation was conducted for empirical verification of the math models and algorithm. Results show that space travel pricing remains the principle of market equilibrium but needs to be extended to the spacetime tensor of GRT.

To promote low-carbon and green travel, this study proposes a tripartite evolutionary game model among new energy vehicle manufacturers, consumers, and government agencies. The game strategy combinations of each party and the stability conditions of the equilibrium point in the evolutionary game system are analyzed, and the validity of the conclusions is verified through simulation results. The study shows a strong correlation between the three parties in the evolutionary game system. From the perspective of car manufacturers, the probability of producing new energy vehicles is positively proportional to the subsidy received from new energy policy, the additional revenue gained from the management of the carbon trading scheme, and the fine received for producing conventional fuel vehicles. However, from the consumer perspective, the likelihood that consumers purchase new energy vehicles is positively related to the utility value to consumers and the coverage of public charging points in the city, and inversely related to the sales price of new energy vehicles. From the government perspective, a combination of direct subsidy policies and indirect support strategies should be considered to stimulate the rapid development of the new energy vehicle industry.

Additive manufacturing (AM) offers customization of microstructure and mechanical properties of fabricated components according to the material selected, and process parameters applied. Selective laser melting (SLM) is the commonly used technique for processing high strength aluminum alloys. Selection of SLM process parameters could control the microstructure of parts and their mechanical properties. However, the process parameters limit and defects obtained inside the as-built parts present obstacles to customized part production. This study investigates the influence of SLM process parameters on the quality of as-built Al6061 and AlSi10Mg parts according to the mutual connection between the microstructure characteristics and mechanical properties. The microstructure of both materials was characterized for different parts processed over a wide range of SLM process parameters. The optimized SLM parameters were investigated to eliminate the internal microstructure defects. The behaviour of mechanical properties of parts was presented through regression models generated from the design of experiment (DOE) analysis for the results of hardness, ultimate tensile strength, and yield strength. A comparison between the results obtained and that reported in the literature is presented to illustrate the influence of process parameters, build environment, and powder characteristics on the quality of parts produced. The results obtained from this study could help to customize the part’s quality by satisfying their design requirements in addition to reducing the as-built defects which in turn reduce the amount of the post-processing needed.

Objective: To evaluate the clinical efficacy of antibiotic bone cement plus lateral bone repositioning for severe diabetic foot and its impact on wound healing rate. Methods: Sixty patients with hemodialysis anemia admitted to the endocrinology department of our hospital from July 2020 to July 2021 were included and randomly assigned to receive antibiotic bone cement plus lateral bone repositioning (observation group) or vacuum sealing drainage (VSD) (control group). Outcome measures included skin temperature of the affected limb, ankle-brachial index, sensory threshold, foot wound healing, dorsalis pedis artery hemodynamics, lower limb function and clinical efficacy. Results: Antibiotic bone cement plus lateral bone repositioning resulted in significantly higher treatment efficiency and transcutaneous partial pressure of oxygen, smaller wound, and lower trauma pH versus VSD, suggesting that antibiotic bone cement plus lateral bone repositioning contributes to potentiating the treatment efficacy and reducing the foot ulcer trauma, thereby facilitating rapid recovery. Patients given antibiotic bone cement plus lateral bone repositioning had larger vascular internal diameter and blood flow and better sensory conduction velocity of the common peroneal nerve and the motor conduction velocity of the tibial nerve versus those given VSD, indicating its vascular and neurological benefits. Conclusion: Antibiotic bone cement plus lateral bone repositioning enhances the treatment efficiency, boosts trauma healing, and promotes postoperative functional recovery of patients.

The stability and optimal control for an SIS epidemic model with demographics and heterogeneous control strategies (immunization and quarantine) on complex networks are investigated. The epidemic threshold, disease-free and endemic equilibria are derived. Then, global asymptotical stability about the two equilibria are studied based on different methods. Furthermore, the optimal control issue about the system is also considered. We obtain the existence and uniqueness of the optimal control and optimal control tactics. Some numerical simulations were conducted to illustrate and supplement the theoretical results. Meanwhile, the effects of the combination of various immunization and quarantine schemes are studied and also compared with the optimal control strategies.

Background: Along with sarcopenia, delayed blood pressure (BP) recovery after standing and orthostatic hypotension (OH) are among key clinical challenges associated with ageing. Previous studies have reported an association between sarcopenia and delayed orthostatic BP recovery and OH. However, the haemodynamic mechanisms underlying this association remain unclear. Methods: 107 attendees to a falls and syncope clinic aged 50+ years underwent an active stand test with non-invasive beat-to-beat haemodynamic measurement. Hand grip strength and 5-chair stands time were measured. Muscle mass was estimated using bioelectrical impedance analysis, and participants were classified as non-sarcopenic and sarcopenic. Mixed effects models with linear splines were used to model the effect of sarcopenia status on Modelflow®-derived mean arterial pressure (MAP), cardiac output (CO), total peripheral resistance (TPR), stroke volume (SV) and heart rate (HR) after standing, while controlling for potential confounders. Results: Sarcopenia was associated with: attenuated recovery of MAP in the 10-20s period after standing (β -0.67, P<0.001); attenuated rise to peak (0-10s) and recovery from peak (10-20s) of CO (β -0.05, P<0.001; β 0.06, P<0.001); attenuated recovery (10-20s) of TPR from nadir (β -0.02, P<0.001) and attenuated recovery from peak (10-20s) of SV (β 0.54, P<0.001). HR was not significantly associated with sarcopenia status at any time interval after standing. Conclusion: The attenuated BP recovery after standing seen in sarcopenia appears to be driven by initial diminished peak of CO followed by attenuated recovery of CO from peak and TPR from nadir. The CO finding appears to be driven by SV rather than HR. Potential mechanisms for these findings include: cardio-sarcopenia, the effects of sarcopenia on the autonomic nervous system and/or the skeletal muscle pump.

In this paper, the methods and their analysis for estimating the location of three dimension (3-D) single source buried in lossy medium are presented with uniform circular array (UCA). The mathematical model of the signal in the lossy medium is proposed. Using location information in the covariance matrix obtained by sensors’ output, the equations of the source location (azimuth angle, elevation angle and range) are obtained. The phase and amplitude of the covariance matrix function are used to process these equations respectively. Then, the phase and amplitude of the covariance matrix function are used to process the source localization in the conductive medium together. By analyzing the characteristics of the proposed methods and MUSIC method, the computational complexity and the valid range of these methods are given. From the results, whether the loss is known, we can choose the appropriate method to process the issues (localization in lossless medium or lossy medium).

The popularity and development of social media has made it more and more convenient to spread rumors, and it has become especially important to detect rumor information from massive amounts of information. Most of the traditional rumor detection methods use content characteristics or propagation structure to mine rumor characteristics, ignoring the fusion characteristics of content and structure and their interaction characteristics. Therefore, a novel rumor detection method based on heterogeneous convolutional networks is proposed. Firstly, this paper constructs a heterogeneous map of joint rumor content and propagation structure to explore the interaction between content and propagation structure during rumor propagation and obtain rumor representation. On that basis, this paper uses the deep residual graph convolutional neural network to construct the content and structure interaction information of the current network propagation model. Finally, this paper uses the two datasets of Twitter15 and Twitter16 to verify the proposed method. Experimental results show that the proposed method has higher detection accuracy than the traditional rumor detection method.

In order to study the collapse failure of shaft wall of high depth inclined ore-pass under ore impact wear behavior, 25 ore-passes in a deep mine in Yunnan, China were investigated. Considering the ore-pass structural characteristics and the impact wear effect of ore on shaft wall, the shaft wall damage model of high depth inclined ore-pass is constructed based on the contact mechanics theory. Furthermore, No. 1#, 2#, 3# and 9# ore-passes of the mine are taken as examples for analysis, and the three results of theoretical analysis, numerical simulation and engineering case are used for comparison and verification. The shaft wall damage degree is predicted, and the damage mechanism between total shaft wall damage volume Qtol and ore-pass depth H, ore-pass dip angle θ, inclined angle of chute α, shaft diameter D and ore block size P is quantitatively investigated. The results show that the rationality of the proposed model is verified by numerical analysis and field engineering situations. Moreover, the deeper ore-pass depth H, the more shaft wall damage volume Qtol with the increase of collision frequency. Qtol increases exponentially with P and increases gradually with D. With the increase of θ or α, Qtol increases generally first and then decreases. Therefore, Qtol can be effectively reduced by selecting the appropriate structure parameters of ore-pass and adopting the technology of drilling straight ore-pass. This work provides technical support for long period safe operation of high depth inclined ore-pass.

Fusarium dry rot is one of the major postharvest potato diseases of during storage after harvest, which not only results in quality degradation but also brings up huge economic losses. The dis-ease can be elicited by some species of Fusarium, the pathogenic fungi of Fusarium causing potato dry rot are considerably diverse in various countries and regions. Fusarium spp. infection is as-sociated with dry rot produce mycotoxins, which has phytotoxicity and mycotoxicoses on hu-mans and animals. Chemical synthetic fungicide is considered as the main control measure to Fusarium dry rot of potato, nevertheless, it is unfortunate that the persistent application inevitably results in the emergency of resistant strain and environmental contamination. A comprehensive disease control strategy includes potato cultivar selection, appropriate cultural practices (crop rotation, cultivate pattern, fertilization, and irrigation), harvesting process and postharvest treatment (harvesting, classification, packaging, wound healing), storage condition (environ-mental disinfection, temperature, humidity and gas composition) along with the application of fungicide pre-harvest or postharvest. Recently, emerging studies indicated that eco-friendly strategies include physical control, chemical methods (such as the application of generally rec-ognized as safe (GRAS) compounds or chemical (elicitors) and biological control have been in-troduced to combat Fusarium dry rot of potato.

With the recent developments in augmented reality (AR) technologies comes an increased interest in the use of smart glasses for hands-on training. Whether this interest is turned into market success or not depends at the least on whether the interaction with smart AR glasses satisfies users, an aspect of AR use that so far has received little attention. With this contribution, we seek to change this. The objective of the article, therefore, is to investigate user satisfaction in AR applied to three cases of practical use. User satisfaction of AR can be broken down into satisfaction with the interaction and satisfaction with the delivery device. A total of 142 participants from three different industrial sectors contributed to this study, namely, aeronautics, medicine, and astronautics. In our analysis, we investigated the influence of different factors, such as age, gender, level of education, level of Internet knowledge, and the roles of the participants in the different sectors. Even though users were not familiar with the smart glasses, results show that general computer knowledge has a positive effect on user satisfaction. Further analysis using two-factor interactions shows that there is no significant interaction between the different factors and user satisfaction. The results of the study affirm that the questionnaires developed for user satisfaction of smart glasses and the AR application performed well, but leave room for improvement.

Litsea cubeba, an important medicinal plant, is widely used as traditional Chinese medicine and spice. Using cytotoxicity-guided fractionation, nine new lignans (1-9) and eleven known analogues (10-19) were obtained from the EtOH extract of the twigs of L. cubeba. Their structures were assigned by extensive 1D and 2D NMR experiments, and the absolute configurations were resolved by specific rotation and a combination of experimental and theoretically calculated electronic circular dichroism (ECD) spectra. In the cytotoxicity assay, 7',9-epoxylignans with feruloyl or cinnamoyl group (7-9, 13 and 14) were selectively cytotoxic against NCI-H1650 cell line, while the dibenzylbutyrolactone lignans (17-19) exerted cytotoxicities against HCT-116 and A2780 cell lines. The results highlighted the structure-activity relationship importance of a feruloyl or a cinnamoyl moiety at C-9′ or/and C-7 ketone in 7',9-epoxylignans. Furthermore, compound 11 was moderate active toward protein tyrosine phosphatase 1B (PTP1B) with an IC50 value of 13.5 μM, and compounds 4-6, 11 and 12 displayed inhibitions against LPS-induced NO production in RAW264.7 macrophages, with IC50 values of 46.8, 50.1, 58.6, 47.5, and 66.5 μM, respectively.

A novel scheme that can simultaneously measure the Doppler frequency shift (DFS) and angle of arrival (AOA) of microwave signals is proposed. At the signal receiving unit (SRU), two echo signals and the reference signal are modulated by a Sagnac loop structure and sent to the central station (CS) for processing. At the CS, two low-frequency electrical signals are generated after polarization control and photoelectric conversion. The DFS without direction ambiguity and wide AOA measurement can be real-time acquired by monitoring the frequency and power of the two low-frequency electrical signals. In the simulation, an unambiguous DFS measurement with errors of ±3×10-3 Hz and a -90° to 90° AOA measurement range with errors of less than ±0.5° are realized. The safety and robustness of the system to environmental disturbance are improved, and it is more suitable for the modern electronic warfare system.

In order to better understand the source-sink flow and relationships of Zinc (Zn) and other nutrients in wheat (Triticum aestivum L.) plants for biofortification and improving grain nutritional quality, effects of reducing photoassimilate source (through the flag leaf removal and spike shading) or sink (through 50% spikelets removal) in the field on accumulation of Zn and other nutrients in wheat grains of two cultivars (Jimai 22 and Jimai 44) were investigated under two soil Zn application levels. The single panicle weight (SPW), kernel number per spike (KNPS), thousand kernel weight (TKW), total grain weight (TGW), concentrations and yields of various nutrient elements (Zn, Fe, Mn, Cu, N, P, K, Ca and Mg), phytate phosphorus (phytate-P), phytic acid (PA) and phytohormones (ABA: abscisic acid, and the ethylene precursor ACC: 1-aminocylopropane-1-carboxylic acid), and C/N ratios were determined. Soil Zn application significantly increased concentrations of grain Zn, N and K. Cultivars showing higher grain yields had lower grain protein and micronutrient nutritional quality. SPW, KNPS, TKW (with an exception of TKW in half spikelets removal), TGW, and nutrient yields in wheat grains were most severely reduced by half spiklets removal, secondly by spike shading, and slightly by flag leaf removal. Grain concentrations of Zn, N and Mg consistently showed negative correlations with SPW, KNPS and TGW, but positively with TKW. There were general positive correlations among grain concentrations of Zn, Fe, Mn, Cu, N and Mg, and bioavailability of Zn and Fe (estimated by molar ratios of PA/Zn, PA × Ca/Zn, PA/Fe, or PA × Ca/Fe). Although concentrations of Zn and Fe were increased and Ca was decreased in treatments of half spikelets removal and spike shading, the simultaneously increased PA limited the increase in bioavailability of Zn and Fe. In general, different nutrient elements interact with each other and are affected to different degrees by source-sink manipulations. Elevated endogenous ABA levels and ABA/ACC ratios were associated with increased TKW and grain-filling of Zn, Mn, Ca and Mg, and inhibited K in wheat grains. However, effects of ACC were diametrically opposite. These results provide basis for wheat grain biofortification to alleviate human malnutrition.

Background: Hepatocellular carcinoma (HCC) is one of the most prevalent cancers in human populations worldwide. Conversely, Huanglian Decoction is one of the most important Chinese medicine formulas, with the potential to treat cancer. Methods: To identify differentially expressed genes (DEG), we herein downloaded gene expression profile data from the TCGA (TCGA-LIHC) and GEO (GSE45436) databases. We obtained phytochemicals of the four constituent herbs of Huanglian Decoction from the traditional Chinese medicine systems pharmacology database and analysis platform (TCMSP). We also established a regulatory network of DEG and their drug target genes and subsequently analyzed key genes using bioinformatic approaches. Furthermore, we explored the effect of Huanglian Decoction by conducting in vitro experiments so as to verify the prediction. In particular, the CCNB1 gene was knockdown to verify the primary target of this Decoction. Results: Based on the results of network pharmacological analysis, we revealed that there are 5 bioactive compounds in Huanglian Decoction acting on HCC. In addition, our findings confirmed that CCNB1 was the primary key gene, which can be highly expressed in tumors and was significantly associated with a worse prognosis (P = 0.002) according to PPI network analysis of the target genes of these five compounds, as well as expression and prognosis analyses in tumors. We also noted that CCNB1 can be used as an independent prognostic indicator of HCC (P < 0.01). Moreover, in vitro experimental results demonstrate that Huanglian Decoction can significantly inhibit the growth, migration, and invasion of HCC cells. Finally, further analysis showed that this Decoction may inhibit the growth of HCC cells by down-regulating the expression level of CCNB1.

The prediction of stock prices holds significant implications for researchers and investors in evaluating stock value and risk. In recent years, researchers have increasingly replaced traditional machine learning methods with deep learning approaches in this domain. However, the application of deep learning in forecasting stock prices is confronted with the challenge of overfitting. To address the issue of overfitting and enhance predictive accuracy, this study proposes a stock prediction model based on GRU (Gated Recurrent Unit) with reconstructed datasets. This model integrates data from other stocks within the same industry, thereby enriching the extracted features and mitigating the risk of overfitting. Additionally, an auxiliary module is employed to augment the volume of data through dataset reconstruction, thereby enhancing the model’s training comprehensiveness and generalization capabilities. Experimental results demonstrate a substantial improvement in prediction accuracy across various industries.

In the world city theory, most researchers focus on the service sector in the urban economy and less discuss the role of manufacturing. However, the path of only emphasizing financial and corporate service could not fit the sustainability concept. Compared to Anglo-American world city, Global South’s world cities have distinct pathway to be industrialization, tertiarization and globalization. This paper adopted dynamic historic perspective with first-hand materials including in-depth interviews with managers and government officers and second-hand data including yearbook statics and economic census to closely examine the emerging world city-- ‘World Factory’ in Global South, Guangzhou in China, from 1949 to 2015, to emphasize how manufacturing affects the urban globalization through three dimensions, economic, social and spatial dimensions. To make the confirmation of the role of manufacturing in Guangzhou as sustainable world city, we find manufacturing in Guangzhou builds up the basic foundation of export-oriented economy and makes positive effects on urban economic transformation. In addition, manufacturing remains important source of employment and foreign immigration. Along with urbanization and industrialization, urban spatial expansion and aggregation changes with different urban development concept. We provide new insights on multiple globalization on manufacturing for sustainable world city.

Kombucha is a popular sparkling sugared tea, fermented by a symbiotic culture of acetic acid bacteria (AAB) and yeast. The demand for Kombucha is increasing worldwide mainly due to its perceived health benefits and appealing sensory properties. This study isolated and characterised the dominant AAB and yeast from starter culture and Kombucha broth after 0, 1, 3, 5, 7, 9, 11, and 14 days of fermentation at ambient temperature (~22°C). Changes in the microbial composition were associated with variations in the physico-chemical characteristics of Kombucha tea, such as pH, titratable acidity, and total soluble solids (TSS). During fermentation, the acidity increased, and TSS decreased. The yield, moisture content and water activity of the cellulosic pellicles which had developed by the end of fermentation were attributed to the presence of AAB. Yeast and AAB were isolated from the Kombucha samples using glucose yeast extract mannitol ethanol acetic acid (GYMEA) and yeast extract glucose chloramphenicol (YGC) media respectively, using serial dilutions. Phenotypic and taxonomic identification of AAB and yeast were determined by morphological and biochemical characterisation, followed by sequence analysis of the ribosomal RNA gene (16S rRNA for AAB and ITS for yeast). The dominant AAB species in the cellulosic pellicle and Kombucha broth was identified as Komagataeibacter rhaeticus. The yeast isolates belonged to Debaryomyces prosopidis and Zygosaccharomyces lentus.

The pathogen Cryptococcus neoformans is a major cause of fungal meningitis in humans. As with other melanotic microorganisms associated with human diseases, the cell wall-associated melanin of C. neoformans is a major virulence factor that contributes to its ability to evade host immune responses. The levels of melanin substrate and the regulation of melanin formation could be influenced by the microbiota-gut-brain axis. Moreover, recent studies show that C. neoformans infection causes dysbiosis in the human gut microbiome. In this review, we discuss the potential association between cryptococcal meningitis and the gut microbiome. Additionally, we emphasize the promising prospects of targeting the gut microbiome as a means of diagnosing and treating this debilitating disease.

Additive manufacturing (AM) provides customization of the microstructure and mechanical properties of components. Selective laser melting (SLM) is the commonly used technique for processing high strength Aluminum alloys. Selection of SLM process parameters could control the microstructure of fabricated parts and their mechanical properties. However, process parameter limits and defects inside the as-built parts present obstacles to customized part production. This study is the second part of a comprehensive work that investigates the influence of SLM process parameters on the quality of as-built Al6061 and AlSi10Mg parts. The microstructure of both materials was characterized for different parts processed over a wide range of SLM process parameters. The optimized SLM parameters were investigated to eliminate the internal microstructure defects. Mechanical properties of the parts were illustrated by regression models generated with design of experiment (DOE) analysis. The results reported in this study were compared to previous studies, illustrating how the process parameters and powder characteristics could affect the quality of produced parts.

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

In this paper, thin plate theory and moderately thick plate theory are proposed for analyzing the bending problem of rectangular plates with stepped thickness resting on elastic half-space foundation. The ground reaction is considered as an unknown coefficient and the hypothesis of Winkler foundation model and two-parameter ground model is eliminated in this method, so as to obtain the law of internal force distribution of the plate and the distribution law of contact reaction force between the stepped rectangular plate and foundation. The stepped rectangular plate is divided into upper and lower plates, and thin plate theory and moderately thick plate theory are used to obtain the analytical solution. The obtained analytical solutions in this paper are compared with results reported in other publications to verify the accuracy of this method. The effects of the elastic modulus and dimensions of the plate, and theory of plate are also considered. The analytical solutions show that it is feasible to decompose the stepped rectangular plate into two plates for analyzing the bending properties of stepped rectangular plate, and this method provide a reference for the study of multilayer stepped rectangular plates.

Osteoporosis is a common problem in orthopedic medicine, and it has become an important medical issue in orthopedics as Taiwan is gradually becoming an aging society. In the diagnosis of osteoporosis, the bone mineral density (BMD) derived from dual-energy X-ray absorptiometry (DXA) is the main criterion for orthopedic diagnosis of osteoporosis, but due to the high cost of this equipment and the lower penetration rate of the equipment compared to the X-ray images, the problem of osteoporosis has not been effectively solved for many people who suffer from osteoporosis, however, at present, in clinical diagnosis, doctors are not yet able to accurately interpret X-ray images for osteoporosis manually, and must rely on the data obtained from DXA. In recent years, with the continuous development of artificial intelligence, especially in machine learning and deep learning, significant progress has been made in image recognition. Therefore, it is worthwhile to revisit whether it is possible to use a convolutional neural network model to read a hip X-ray image and then predict the patient's BMD. In this study, we proposed a hip X-ray image segmentation model and a hip X-ray image recognition classification model. First, we used the U-Net model as a framework to segment the femoral neck, greater trochanter, wards triangle, and the total hip in the hip X-ray images. We then performed image matting and data augmentation. Finally, we constructed a predictive model for osteoporosis using deep learning algorithms. In the segmentation experiments, we used intersection over union (IoU) as the evaluation metric for image segmentation, and both the U-Net and U-Net++ models achieved segmentation results greater than or equal to 0.5. In the classification experiments, using the T-score as the classification basis, the total hip using the DenseNet121 model has the highest accuracy of 74%.

Ferulic acid esters have been suggested as a group of natural chemicals with sunscreen function. The study aimed to utilize an environment-friendly enzymatic method to produce octyl ferulate by esterification of ferulic acid with octanol. The Box-Behnken design with response surface methodology (RSM) was adopted to evaluate the effects of synthesis variables, including reaction temperature (70–90 °C), enzyme amount (1000–2000 PLU) and stir speed (50–150 rpm), on the molar conversion of octyl ferulate. According to the joint test, both the reaction temperature and enzyme amount had great impacts on the molar conversion. RSM-developed second-order polynomial equation further showed great ability on data-fitting. Based on ridge max analysis, the optimum parameters for the biocatalyzed reaction were: 72 h reaction time, 92.2 °C reaction temperature, 1831 PLU enzyme amount and 92.4 rpm stir speed, respectively. Finally, the molar conversion of octyl ferulate under optimum condition was verified to be 93.2 ± 1.5%. In conclusion, high yield of octyl ferulate synthesized by commercial immobilized lipase under elevated temperature conditions has been suggested, which our findings could broaden the utilization of the lipase and provide a biocatalytic approach, instead of the chemical method, for ferulic acid ester synthesis.

Additive manufacturing (AM) of high strength Al alloys promises to enhance the performance of critical components related to various aerospace and automotive applications. The key advantage of AM is its ability to generate lightweight, robust, and complex shapes. However, the characteristics of the as-built parts may represent an obstacle to satisfy the part quality requirements. The current study investigates the influence of selective laser melting (SLM) process parameters on the quality of parts fabricated from different Al alloys. A design of experiment (DOE) is used to analyze relative density, porosity, surface roughness, and dimensional accuracy according to the interaction effect between the SLM process parameters. The results show a range of energy densities and SLM process parameters for the AlSi10Mg and Al6061 alloys needed to achieve “optimum” values for each performance characteristic. A process map is developed for each material by combining the optimized range of SLM process parameters for each characteristic to ensure good quality of the as-built parts. The second part of this study investigates the effect of SLM process parameters on the microstructure and mechanical properties of the same Al alloys. This comprehensive study is also aimed at reducing the amount of post-processing needed.

Polysaccharide from Ficus carica L. (FCP) exert multiple biological activities, as a biological macromolecule, the available knowledge about the specific structures and mechanisms of biological activity of purified 'Brunswick' fig polysaccharide is currently limited. In the present study, by chemical purification and characteristics identified via specific instruments, and then the impact of FCP on the immunomodulation activity in vitro and in vivo was examined. Structural char-acteristics showed that the molecular weight of the FCP was determined to be 127.5 kDa, the primary monosaccharides present in the FCP were galacturonic acid (GalA), arabinose (Ara), galactose (Gal), rhamnose (Rha), glucose (Glc), and xylose (Xyl) at a ratio of 0.321:0.287:0.269:0.091:0.013:0.011. Based on the investigation of in vitro immunomodulatory ac-tivity, FCP was found to stimulate the production of NO, TNF-α, and IL-6 and increased the pi-nocytic activity of macrophages. Further analysis revealed that FCP activated macrophages by interacting with toll-like receptor 4 (TLR4). Moreover, the in vivo test results indicate that FCP showed significant increase serum pro-inflammatory factors in immunosuppressed mice. Overall, this study suggests that FCP has the potential to be utilized as a novel immunomodulator in the pharmaceutical and functional food industries.

Ultrasonic-guided lamb wave approach is an effective non-destructive testing (NDT) method used for detecting localized mechanical damage, corrosion, and welding defects experienced in metallic pipelines. Signal processing of the guided waves is often challenged due to the complexity of operational conditions and environments in the pipelines. Machine learning approaches in recent years, including convolutional neural networks (CNN) and long short-term memory (LSTM), have exhibited their advantages to overcome these challenges for signal process and data classification of complex systems, thus great potential for damage detection of critical oil/gas pipeline structures. In this study, a CNN-LSTM hybrid model is utilized for decoding ultrasonic guided waves for damage detection of metallic pipelines, and twenty-nine features are extracted as input to classify different types of defects from metallic pipes. The prediction capacity of the CNN-LSTM model is assessed by comparing it to the CNN and LSTM. The results demonstrate that the CNN-LSTM hybrid model exhibits much higher accuracy, with 94.8%, as compared to those of CNN and LSTM. Interestingly, the results also reveal that predetermined features, including time-, frequency-, and time-frequency domains, could significantly improve the robustness of the deep learning approaches, even though the deep learning approaches are often believed they include automated feature extraction, without the hand-crafted steps as the shallow learning do. Furthermore, the CNN-LSTM model displays higher performance when the noise level is relatively low (e.g., SNR=9 or higher), as compared to the other two models, but its prediction drops gradually with the increase of the noise.

To alleviate the contradiction between the increasing demand for water and the shortage of resources and to provide a favorable institutional environment for water rights trading, the Chinese government has strengthened the top-level design of water management system. However, the water-rich regions (southern regions of China) have good water resource endowment and a surplus of total water consumption indicators. Does this mean that there is no incentive and no need to conduct water rights trading in these regions? Through the investigation of water rights circulation cases in the Taihu Basin, a typical water-rich region of China, we established the existence of trading demand and some difficulties in conducting transactions. This paper argues that the needs of trading include alleviating the water gap in regional development, solving the water demand for large new projects, coordinating trans-jurisdiction water disputes. The plight of trading includes the lack of awareness, irregular process, excessive administrative intervention, and imperfect trading system.

The technological development of piezoelectric materials is crucial for developing wearable and flexible electromechanical devices. There are many inorganic materials with piezoelectric effects, such as piezoelectric ceramics, aluminum nitride, and zinc oxide. They all have very high piezoelectric coefficients and large piezoelectric response ranges. The characteristics of high hardness and low tenacity make inorganic piezoelectric materials unsuitable for flexible devices that require frequent bending. Polyvinylidene fluoride (PVDF) and its derivatives are the most popular materials used in flexible electromechanical devices in recent years and have high flexibility, high sensitivity, high ductility, and a certain piezoelectric coefficient. Owing to increasing the piezoelectric coefficient of PVDF, researchers are committed to optimizing PVDF materials and enhancing their polarity by a series of means to further improve their mechanical–electrical conversion efficiency. This paper reviews the latest PVDF-related optimization materials, related processing and polarization methods, and the applications of these materials such as those in wearable functional devices, chemical sensors, biosensors, and flexible actuator devices for flexible micro-electromechanical devices. We also discuss the challenges of wearable devices based on flexible piezoelectric polymer, consider where further practical applications could be.

The ethylene-regulated hypocotyl elongation of Arabidopsis thaliana's involves many transcription factors. The specific role of MYC transcription factors in ethylene signal transduction is not completely understood. The results here revealed that two MYCs, MYC2 and MYC3, act as negative regulators in ethylene-suppressed hypocotyl elongation. Etiolated seedlings of the lost-of-function mutant of MYC2 or MYC3 were longer than wild type seedlings. Single- or double-null mutants of MYC2 and MYC3 displayed an enhanced response to ACC(1-aminocyclopropane-1-carboxylate), the ethylene precursor, compared to wild type seedlings. MYC2 and MYC3 directly bind to the promoter zone of ERF1, suppressing its expression. Additionally, EIN3, a key component in ethylene signaling, interacts with MYC2 or MYC3 and suppresses their binding to ERF1’s promoter. MYC2 and MYC3 play crucial roles in the ethylene-regulated expression of functional genes. The results revealed these transcription factors’ novel role and functional mechanism in ethylene signal transduction.

The intestinal microbial community of aquatic animals is closely related to the environment and thus affects the health of aquatic animals. Here we investigated annual variation of intestinal bacteria community structures of Ruditapes philippinarum cultured using two different methods, bottom sown and raft hanging. Bacterial diversity of seawater and sediment in different seasons was examined as well. Correlation between R. philippinarum intestinal bacteria community structures and environmental factors was analyzed. The results showed that in the two aquculture areas where R. philippinarum was differentially cultured, bacteria community structure of seawater and sediment both altered with seasons. However, neither seasonal changes nor difference in culture methods could significantly affect the intestinal bacteria community structures of R. philippinarum. Additionally, in terms of the alpha diversity of intestinal bacteria communities, there was no significant difference in R. philippinarum cultured using the two methods. For benthic cultured clams, alpha diversity of the intestinal bacterial communities was often higher than that of the environmental bacterial communities. For raft hanging cultured calms, Alpha diversity of the intestinal bacterial communities was normally comparable with that of the environmental counterparts. Beta diversity analysis showed that the intestinal bacterial community structure of R. philippinarum was mainly determined by both deterministic and stochastic processes. Correlation analysis showed that the intestinal bacterial community structures of R. philippinarum were determined by a variety of environmental factors. For clams collected from the benthic culture area, the intestinal bacterial structure was more correlated with the physicochemical properties of sediment in comparing with those of seawater. For clams collected from the raft-culture area, the intestinal bacterial structure was mainly determined by the phsicochemical characteristics of seawater. This study helps us to better understand the bacterial community structure in complex aquaculture ecosystems, providing a reference for healthy shellfish aquaculture and ecosystem protection in aquaculture area.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

The moisture content of maize seed is an important indicator for evaluating seed quality and a fundamental item in grain testing. The experiment used direct drying method to measure the moisture content of 80 different varieties of maize samples, and captured their images using a hyperspectral imaging (HSI) system in the spectral range of 1100~2498nm. By comparing seven spectral preprocessing methods, the PLSR model established after Normalize pretreatment had the best effect. The characteristic wavelengths were selected by Successive Projections Algorithm (SPA), Competitive Adaptive Reweighted Sampling (CARS) and Uninformative Variable Elimination (UVE). Twelve prediction models were established for full band spectra and characteristic wavelengths based on PLSR, PCR and SVM. By comparing the performance of the prediction models, it was found the Normalize-SPA-PLSR algorithm was optimized. The values of RC2 and RP2 in the model were higher, which were 0.9936 and 0.9933, respectively, while the values of RMSEP and RMSECV were lower, which were 0.0357 and 0.0380, respectively. The Normalize-SPA-PLSR model was used as a visual prediction model for moisture content of maize seed, the 20 maize varieties in the prediction set were visualized to obtain visualized color images of moisture content. The color differences between different moisture content images were significant. The result indicated that hyperspectral imaging could accurately, rapidly, and non-destructive predict moisture content of maize seed, which provided technical support for moisture content detection in the process of maize harvest, storage and processing.

The accumulation of foam cells in arterial intima and the accompanied chronic inflammation are considered major causes of neoatherosclerosis and restenosis. However, both the underlying mechanism and effective treatment for the disease are yet to be uncovered. In this study, we combined transcriptome profiling of restenosis artery tissue and bioinformatic analysis to reveal that NLRP3 inflammasome is markedly upregulated in restenosis and that several restenosis re-lated DEGs are also targets of mulberry extract, a natural dietary supplement used in traditional Chinese medicine to improve liver vitality. Further pathway enrichment analysis identified MAPK signaling pathway to be involved in the inflammatory response of foam cells. Consistently, immunofluorescence microscopy shows co-localization of NLRP3 with CD68+ macrophages. We then evaluated the efficacy of mulberry extract in inhibiting both the formation of foam cells and their inflammatory response. We demonstrated that mulberry extract suppresses the formation of ox-LDL induced foam cells, possibly by upregulating the cholesterol efflux genes ABCA1 and ABCG1 to inhibit intracellular lipid accumulation. In addition, mulberry extract dampens NLRP3 inflammasome activation by stressing the MAPK signaling pathway. Collectively, our mecha-nistic and functional studies unveil the therapeutic value of mulberry extract in neoatherosclerosis and restenosis treatment by regulating lipid metabolism and inflammatory response of foam cells.