In the present study, an attempt was made to induce rooting from single-node cuttings of hybrid aspen (Populus tremula L. ×P. tremuloides Michx.) with different concentrations of IAA, IBA and NAA during rooting. Among the three auxins used, NAA showed more effective induction on rooting as compared to IAA and IBA at the whole level. Thereafter, NAA was used further in experiments for anatomical and biochemical investigation. The results showed that it took 12 days from the differentiation of primordium to the appearance of young adventitious roots with NAA application. It was found that endogenous IAA, ZR and GA3 levels increased, but ABA decreased in cuttings with 0.54 mM NAA treatment. In contrast to the endogenous IAA level, NAA had negative effect on IAA-oxidase (IAAO) activity. Similarly, the decreased peroxidase (POD) activity, consistent with down-regulation of expressed levels of POD1 and POD2, was observed in NAA-treated cuttings. Whereas, NAA resulted in a higher activity in polyphenol oxidase (PPO) compared to the control cuttings. Collectively, the study highlighted that 0.54 mM NAA is efficient on rooting in hybrid aspen, and its effect on metabolic changes during rooting is discussed, which provide valuable information for propagating hybrid aspen.

A lightweight composite bridge deck system composed of steel orthotropic deck stiffened with thin Ultra-High Performance Concrete (UHPC) layer is developed to eliminate fatigue cracks in orthotropic steel decks. During the construction and operation period of the bridge, the debonding between the steel deck and the UHPC layer may introduce the several issues, such as crack-induced water invasion and distinct reduction of the shear resistance. In the study, an effective and novel non-destructive interface condition monitoring approach using piezoelectric lead zirconate titanate (PZT)-based technologies is proposed to detect interfacial delamination between steel deck and UHPC layer. Experimental tests are performed on several steel-UHPC composite slabs and a conventional steel-concrete composite slab. The thin styrofoam sheets with different sizes and thicknesses are set on different locations of the steel deck as the artificial debondings. The PZT ceramic patches are bonded on the surfaces of the steel deck and UHPC layer as the actuators/sensors. An improved PSO (Particle Swarm Optimization)-K-means clustering algorithms is proposed to obtain the debonding patterns based on the feature data set. The laboratory tests demonstrate that the proposed approach provides an effective and accurate way to detect interfacial debonding of steel-UHPC composite slab.

Information encryption and anti-counterfeiting play an important role in many aspects of daily life, such as in minimizing economic losses, protecting secure communication and public security, and so on. Owing to the high information capacity and ease of operation, luminescent materials for advanced information encryption and anti-counterfeiting are essential to meet the increasing demand on encryption security. Herein, we summarize two emerging luminescent materials for information encryption and anti-counterfeiting, the AIE materials and room-temperature phosphorescent materials. At last, we discuss the opportunities and anticipations of these two information encryption and anti-counterfeiting materials.

In the face of the current energy and environment problems, the full use of biomass resources instead of fossil energy to produce a series of high-value chemicals has great application prospects. 5-hydroxymethylfurfural (HMF), which can be synthesized from lignocellulose as raw material, is an important biological platform molecule. Its preparation and catalytic oxidation of subsequent products have important research significance and practical value. In the actual production process, porous organic polymer (POPs) catalysts are highly suitable for biomass catalytic conversion due to its high efficiency, low cost, good designability, and environmentally friendly features. Here, we briefly described the application of various types of POPs (including COFs、PAFs、HCPs、CMPs) in the preparation and catalytic conversion of HMF from lignocellulosic biomass, and analyzed the influence of the structural properties of catalysts for the catalytic performance. Finally, we summarized some challenges that POPs catalysts will face in biomass catalytic conversion, and prospected the important research directions in future. This review would provide valuable references for the efficient conversion of biomass resources into high-value chemicals in practical applications.

Research on the development of new lightweight Al-Li alloys using selective laser melting pro-cess has great potential for industrial applications. This paper reports on the development of novel aluminum-lithium alloys using selective laser melting technology. Al-Cu-Li-Mg-Ag-Sc-Zr pre-alloyed powders with lithium contents of 1 wt.%, 2 wt.% and 3 wt.%, respectively, were prepared by inert gas atomization. After SLM process optimization, the microstructure and me-chanical properties of the as-formed specimens were investigated. The densification of the three newly developed alloys are 99.51 %, 98.96 % and 92.01 %, respectively. They all have good form-ability, with the lithium loss rate about 15 %. The as-formed alloy with 1% Li content presents good comprehensive properties with a yield strength of 412.6 ± 16.0 MPa, an ultimate tensile strength of 461.1 ± 11.7 MPa, and an elongation of 13.6 ± 1.1%. The three alloys exhibit a layered molten pool stacking morphology and have a typical heterostructure. The columnar crystals and equiaxed fine grains are alternately arranged, and most of the precipitated phases are enriched at the grain boundaries. The change of Li content mainly affects the precipitation of Cu-containing phase. When the Li content is 1 wt.%, there are θ phase, T1 phase and TB phase. When Li increased to 2 wt.%, T1 and T2 phases precipitated together. When Li reaches 3 wt.%, δ' phase precipitates with T2 phase. This study provides useful guidance for the future SLM form-ing of new crack-free and high-strength Al-Li alloys.

The demand for industries to enhance sustainability is rising in response to climate change worries. A pervasive and intensifying worldwide environmental problem, plastic pollution has a particularly severe impact on climate change. The production of significant volumes of plastic garbage occurs mostly in Asian regions. So, it's commonplace to talk about pro-environmental conduct nowadays. Indonesia and Taiwan are chosen as case studies of developed and developing regions, respectively. The cultural differences between the two areas do, however, exist in terms of environmental values, and this further influences consumer behavior. In order to understand how environmental education has influenced pro-environmental behavior, this study examines how environmental attitude, knowledge, motivation, and intention have changed as a result of environmental education. By sending electronic questionnaires to a sample of 235 respondents (110 Indonesian and 125 Taiwanese), gathered between March 11 and April 30, 2023, we employ quantitative approaches and data-gathering procedures. The CB-Structural Equation Modelling with AMOS analytical tool is used to examine the data. We are able to draw important conclusions from the study of differences between Indonesian and Taiwanese and make suggestions for more research as well as theoretical and managerial ramifications.

The paper discusses the classification of fuzzy metrics based on their continuity conditions, dividing them into Erceg, Deng, Yang-Shi, and Chen metrics. It explores the relationships between these types of fuzzy metrics, concluding that a Deng metric in [0,1]-topology must also be Erceg, Chen, and Yang-Shi metrics. The paper also proves that the product of countably many Deng pseudo-metric spaces remains a Deng pseudo-metric space, and demonstrates some σ-locally finite properties of Deng metric space. Additionally, the paper constructs two interrelated mappings based on normal space and concludes that if a [0,1]-topological space is T1 and regular, and its topology has a σ-locally finite base, then it is Deng metrizable, and thus Erceg, Yang-Shi, and Chen metrizable as well.

The COVID-19 pandemic has profoundly changed the world and human society in various ways. Infection-related figures are key indicators of the direct impact of the pandemic. In addition to the virus, many vulnerable populations (e.g. patients with complex health conditions) have suffered direct or indirect health impacts, such as delayed treatment or diagnosis of cancer and severe mental illness due to stay-at-home restrictions, or financial issues. Studying these kinds of impacts can provide the community with insights and understanding of how the pandemic has affected patients with health conditions and help inform decision-makers design policies that support various vulnerable populations. This paper surveys analytical work conducted on how COVID-19 has impacted patients with complex health conditions. We categorise vulnerable populations into three specific cohorts: patients with chronic disease, patients with cancer and patients with end-of-life care. We then investigate how each of these cohorts has been impacted by the pandemic. We also identify each cohort from an analytics perspective by leveraging various data collection strategies and analytical methods. The goals of this paper are to provide evidence on how to improve the quality of life for vulnerable populations and to inform a national response strategy for future pandemics, which seems inevitable in a highly globalised economy.

Photocatalytic technology based on specific band structure of semiconductors offers a promising way to solve the urgent energy and environmental issues in modern society. In particular, hydrogen production from water splitting over semiconductor photocatalysts attracts great attention owing to the clean source and application of energy, which highly depends on the performance of photocatalysts. Among the various photocatalysts, TiO2 has been intensively investigated and used extensively due to its outstanding photocatalytic activity, high chemical stability, non-toxicity and low cost. However, pure TiO2 has a wide band gap of approximately 3.2 eV, which limits its photocatalytic activity for water splitting to generate hydrogen only under ultraviolet light, excluding most of the inexhaustible sunlight for human beings. Fortunately, the band gap of semiconductors can be manipulated, in which introducing oxygen defects is one of the most effective measures to narrow the band gap of titanium oxides. This review starts out by the fundamentals of photocatalytic water splitting for hydrogen production over TiO2, discusses the latest progress in this field, and summarizes the various methods and strategies to induce oxygen defects in TiO2 crystals. Then, the next section outlines the modification approaches of oxygen-deficient titanium oxide (TiO2-δ) to further improve its photocatalytic performance. Finally, a brief summary and outlook of the researches on TiO2-δ photocatalysts for water splitting to produce hydrogen were presented.

Abstract: Circuit breakers are affected by multiple lightning strikes after the breaker has been tripped and can break down again, which will reduce the life of the circuit breaker and threaten the stable operation of the power system. Aiming at this problem, the paper obtained the temperature diffusion process of the inrush current process of circuit breaker opening and breaking through the schlieren technique, and combined with the existing image recognition technology to obtain the temperature characteristics of the airflow in the air gap of the contact, and the characteristics of the airflow flow. The results of the study show that the circuit breaker breakdown process generates a shock wave with a velocity approximately equal to the speed of sound under the same conditions. The maximum velocity of the airflow boundary diffusion is about 1/4 of the speed of sound under the same condition, and it decays very fast, reducing to the airflow drift velocity within 10ms after breakdown. The maximum temperature of the thermals is concentrated between 6000 and 8000 K and the temperature change is approximately inversely proportional to the square of time. The research provides the basis for the design of circuit breaker contact structure, opening speed optimization method, interrupter chamber and insulation design optimization.

Recently, NOAA has included GNSS (Global Navigation Satellite System) Radio Occultation (RO) data as one of the crucial long-term observables for weather and climate applications. To include more GNSS RO data in the numerical weather prediction system, the NOAA Commercial Weather Data Pilot program (CWDP) started to explore the commercial RO data available on the market. After two rounds of pilot studies, the CDWP decided to award the first Indefinite Delivery Indefinite Quantity (IDIQ) contract to GeoOptics and Spire Incs. in 2020. This study examines the quality of Spire data products for weather and climate applications. Spire RO data are collected from commercial CubeSats through careful comparison with the data from Formosa Satellite Mission 7–Constellation Observing System for Meteorology, Ionosphere, and Climate-2 (COSMIC-2), ERA-5, and high-quality radiosonde data. The results demonstrated that although with lower Signal-Noise-Ratio (SNR) in general, the pattern of the lowest penetration height for Spire is similar to those for COSMIC-2. The Spire and COSMIC-2 penetrate heights are between 0.6 and 0.8 km altitude at the tropical oceans. Although using different GNSS RO receivers, the precision of Spire STRASP receivers is of the same quality as those of COSMIC-2 Global Positioning System - GPS, GALILEO, and GLObal NAvigation Satellite System – GLONASS (TGRS) receivers. The retrieval accuracy from Spire is very compatible with those from COSMIC-2. We validated Spire temperature and water vapor profiles by comparing them with collocated radiosonde data. Generally, over the height region between 8 km and 16.5 km, the Spire temperature profiles match those from RS41 RAOB very well with temperature biases < 0.02 K. Over the height range from 17.8 to 26.4 km, the temperature differences are ~-0.034 K with RS41 RAOB being warmer. We also estimated the error covariance matrix for Spire, COSMIC-2, and KOMPSAT-5. Results showed that the COSMIC-2 estimated error covariance values are slightly more significant over the oceans at the mid-latitudes (45oN-30oN and 30oS-45oS), which may also be owing to COSMIC-2 SNR being lower at those latitudinal zones.

Barnyardgrass (Echinochloa spp.) is a prevalent type of weed in rice fields worldwide. Despite the growing knowledge concerning allelopathic interference with barnyardgrass, little is understood regarding the competitive mechanisms between allelopathic rice and herbicide-resistant barnyardgrass at the plant physiological level. In this context, a hydroponic system was employed to investigate the root morphological traits and different phytohormones levels of two rice cultivars, i.e., the allelopathic rice cultivar “PI312777” (PI) and the non-allelopathic rice cultivar “Lemont” (LE), when co-planted with quinclorac-resistant and -susceptible barnyardgrass, respectively. The results showed that the shoot and root biomass were greater in the allelopathic rice cultivar. Moreover, the treatments at the two time points induced an increase in shoot and root biomass of PI when subjected to barnyardgrass stress. In terms of root morphology, PI exhibited significantly higher fine-root length in diameters <0.5 mm, a greater number of root tips, and longer root tips compared to LE. In addition, the levels of different plant hormones, including auxin (IAA), abscisic acid (ABA), jasmonic acid (JA), and salicylic acid (SA), known for their diverse adaptation strategies to biotic stress, were analysed. The response to quinclorac-resistant barnyardgrass stress was consistent in terms of the content of well-known stress-related hormones, namely SA and JA. The accumulation of SA and JA was observed in both rice cultivars under the stress of quinclorac-resistant barnyardgrass, with higher contents of these hormones in PI than that in LE. The most significant change was observed in IAA and ABA contents in rice, which decreased significantly from 7 days to 14 days under co-culture stress. Additionally, PI contained higher levels of IAA and ABA than LE in the presence of barnyardgrass stress. This research may aid in the development of strategies for reducing the environmental impact of herbicides through the prudent selection of non-chemical herbicide control tactics.

By reviewing the research of development economics in recent years, five key terms of ‘innovation, coordination, green, openness and sharing’ are extracted, corresponding to the five dimensions of the New Development Concept advocated by China. Based on this, an evaluation index system of the development quality of China's fishery industry is constructed. The spatio-temporal characteristics of China's fishery industry development quality were analyzed by using the provincial panel data from 2007 to 2017. The results show that: i) China's fishery industry overall development quality continues to grow, while the variation of provincial quality is also increasing, and the contribution of innovation quality and sharing quality is increasing, becoming an important sub-dimension leading the overall development quality.ii) there is a significant spatial dependence among provincial quality, and the significance is further strengthening. The Hangzhou Bay area and Bohai Bay area have gradually become a dual-core area where the high-quality development of China's fishery industry agglomeration, and the radiation from the dual-core area to the peripheral areas may still be in the process of enhancement. The spatial and temporal distribution of China’s fishery industry development quality keeps the trend of ‘from northeast to southwest’, which is almost parallel to Hu Huanyong line. The gravity center of its distribution is close to the gravity center of Chinese population and economy, and the development quality experienced a process from relatively concentrated to dispersed and then returned to concentrated, and the development speed in the later period was higher than that in the earlier period. iii) Capital accumulation level is the dominant positive influencing factors, while government support level is the dominant negative influencing factors respectively, and both have significant spatial differentiation among provinces.

Tao and Ming (name) or Tao and Yan (language or speech) is an inseparable pair of important concepts in traditional Chinese language philosophy. In LaoTze’s opinion, Tao could not be spoken out, and language or speech could not reach Tao’s essence. Yan and Tao are separated from each other, and they are paradoxical. All the confusion derives from Yan regardless of how delicate they are. Tao can be expressed in words, but it will never be expressed through common languages. In this article, Tao is regarded as a human being’s thoughts or intentions and is even considered to be the origin of the real world. Language can express people’s thought, although it has some limitations. There exist some contradictions between the real word and the world expressed in words. To enable people to better understand the existence of the real world from multiple perspectives at the language or linguistic level without being constrained by words, this article studies LaoTze’s linguistic philosophy reflected in his opinion on the relationship between Tao and Yan and makes a comparative analysis of modern Western language philosophers’ stand on language (or speech) and existence.

Stem cells can be used to treat diabetic mellitus and complications. ω3-docosahexaenoic acid (DHA) derived lipid mediators are inflammation-resolving and protective. This study found novel DHA-derived 7S,14R-dihydroxy-4Z,8E,10Z,12E,16Z,19Z-docosahexaenoic acid (7S,14R-diHDHA), a maresin-1 stereoisomer biosynthesized by leukocytes and related enzymes. Moreover, 7S,14R-diHDHA can enhance mesenchymal stem cell (MSC) functions in the amelioration of diabetic mellitus and retinal pericyte loss in diabetic db/db mice. MSCs treated with 7S,14R-diHDHA were delivered into db/db mice i.v. every 5 days for 35 days. Blood glucose levels in diabetic mice were lowered by 7S,14R-diHDHA-treated MSCs compared to control and untreated MSC groups, accompanied by improved glucose tolerance and higher blood insulin levels. 7S,14R-diHDHA-treated MSCs increased insulin+ β-cell ratio and decreased glucogan+ α-cell ratio in islets, as well as reduced macrophages in pancreas. 7S,14R-diHDHA induced MSC functions in promoting MIN6 β-cell viability and insulin secretion. 7S,14R-diHDHA induced MSC paracrine functions by increasing the generation of hepatocyte growth factor and vascular endothelial growth factor. Furthermore, 7S,14R-diHDHA enhanced MSC functions to ameliorate diabetes-caused pericyte loss in diabetic retinopathy by increasing their density in retina in db/db mice. Our findings provide a novel strategy for improving therapy for diabetes and diabetic retinopathy using 7S,14R-diHDHA-primed MSCs.

Recently, the outbreak of coronavirus disease 2019 (COVID-19) is threatening human health globally. There is a dire need to find potential therapeutic agents. Angiotensin converting enzyme 2 (ACE2), as an entry receptor of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2), is considered as potential therapeutic target in COVID-19 pandemic. Here, our bioinformatics analysis revealed that the biological function of ACE2 was correlated with regulation of blood pressure and mediation of SARS-CoV-2 entry into host cells. Ten ACE2 cooperative proteins were identified by using STRING with a high score. ACE2 expressed highly in the small intestine, testis, and kidney. The level of ACE2 expression in tumor tissues varies in different types of cancers compared with that in normal tissues. It was worth noting that the expression level of ACE2 in the tumor has no effect on patient survival. MiRNA hsa-miR-942-5p, and three transcription factors (TFs) including Signal transducer and activator of transcription 4 (STAT4), Estrogen related receptor α (ESRRA), and Signal transducer and activator of transcription 3 (STAT3) were selected as novel ACE2 regulators. Moreover, nine potential therapeutic drugs were predicted by two online databases. Thus, our research may expand the overall view of ACE2 in COVID-19 treatment.

In the study, a new correction method was applied to reduce error during detection on mixed pesticide residue in apples by using Raman spectra. Combined with self-built pesticide residues detection system by Raman spectroscopy and the application of surface enhancement technology, rapid real-time qualitative and quantitative analysis of deltamethrin and acetamiprid residues in apples can be applied effectively. In quantitative analysis, compared with the intensity value of characteristic peaks of single pesticide with same concentration, the intensity value of characteristic peaks of the two pesticides decreased after mixing the pesticides, which interferes the results severely. By comparing the difference in the intensity of characteristic peaks of single and mixed pesticides, a correction method is proposed to eliminate the influence of pesticides mixture. Characteristic peak intensity values of gradient concentration pesticide from 10-1 g•kg-1 to 10-6 g•kg-1 and Lagrangian interpolation are applied in the correction method. And a smooth surface is applied to describe the correction ratio of characteristic peak intensity. Through detecting the characteristic peak intensity values of the mixed pesticide, correction ratio will be obtained. Then real values of the peak intensity of pesticides and the content of each component of the mixed pesticide will be acquired by the correction method. Correlation coefficient of model validation exceeds 0.88 generally and Root Mean Square Error also decreases obviously after correction, which proved the reliability of the method.

Micro-grids’ operations offer local reliability; in the event of faults or low voltage/frequency events on the utility side, micro-grids can disconnect from the main grid and operate autonomously while providing the continued supply of power to local customers. With the ever-increasing penetration of renewable generation, however, the operations of micro-grids become increasingly complicated because of the associated fluctuations of voltages. As a result, transformer taps are adjusted frequently, thereby leading to the fast degradation of expensive tap-changer transformers. In the islanding mode, the difficulties also come from the drop of voltage and frequency upon disconnecting from the main grid. To appropriately model the above, the nonlinear AC power flow constraints are necessary. Computationally, the discrete nature of tap-changer operations and the stochasticity caused by renewables add two layers of difficulty on top of a complicated AC-OPF problem. To resolve the above computational difficulties, the main principles of the recently-developed "l1-proximal" Surrogate Lagrangian Relaxation are extended. Testing results based on 9-bus system demonstrate the efficiency of the method to obtain the exact feasible solutions for micro-grid operations thereby avoiding approximations inherent to existing methods, while demonstrating that through the optimization, 1. the number of tap changes is drastically reduced, and 2. the method is capable of handling networks with meshed topologies.

To evaluate the effect of middle meningeal artery embolization (MMAE) on chronic subdural hematoma (CSDH). We enrolled consecutive patients with CSDH who underwent burr hole craniostomy (BHC) between January 2021 and February 2023. The primary outcome was recurrence rate, defined as an increase of hematoma width on imaging compared with the immediate postoperative imaging at a 3-month follow-up. Secondary outcomes included the rate of complications and adverse prognosis. Cohorts were balanced using 1:2 propensity score matching (PSM). A total of 271 patients were eligible for this study and divided into the MMAE group (n=23) and the BHC group (n=205). Compared with the BHC group, there was more use of anticoagulant or antiplatelet medication (47.8% vs 22.4%, P=0.008), bilateral hematoma (19.5% vs 19.5%, P=0.043) and hematoma with septations (47.8% vs 21.5%, P=0.005) in the MMAE group. After PSM, 64 cases were finally successfully matched. The logistic analysis result showed that MMAE was associated with the decreased recurrence rate of CSDH in the cohort after PSM (OR 0.072, 95%CI 0.322~0.746, P=0.028) but not with the improved clinical prognosis (OR 0.065, 95%CI 0.533~4.786, P=0.562). MAAE has a positive therapeutic effect on reducing the recurrence rate of CSDHs as an adjunct postoperative treatment after burr hole surgery.

As an important part of urban terminal delivery, automated guided vehicle (AGV) has been widely used in the field of takeout delivery. Due to the real-time generation of takeout orders, the delivery system is required to be extremely dynamic, so the AGV needs to be dynamically scheduled. At the same time, the uncertainty in the delivery process (such as the meal preparation time) further increases the complexity and difficulty of AGV scheduling. Considering the influence of these two factors, the method of embedding stochastic programming model into rolling mechanism is adopted to optimize the AGV delivery routing. Specifically, To handle real-time orders under dynamic demand, an optimization mechanism based on rolling scheduling framework is proposed, which allows the AGV route to be continuously updated. Different from most VRP models, open chain structure is used to describe the dynamic delivery path of AGV. In order to deal with the impact of uncertain meal preparation time on route planning, a stochastic programming model is formulated with the purpose of minimizing the expectation of order timeout rate and the total customer waiting time. In addition, an effective path merging strategy and after-effects strategy are also considered in the model. In order to solve the proposed mathematical programming model, a multi-objective optimization algorithm based on NSGA-III framework is developed. Finally, a series of experimental results demonstrate the effectiveness and superiority of the proposed model and algorithm.

Piceatannol is a naturally occurring polyphenolic compound that is widely found in grapes, blueberries, mushrooms, passion fruit and other edible fruits and vegetables. It has a variety of biological activities and pharmacological effects, including anti-inflammatory, antioxidation, antiaging, antiviral, antitumor, anticancer, antiatherosclerosis, antiparasitic, immunoregulatory, and cardiovascular protection effects. The aim of this study was to investigate the antiherpesvirus effects of piceatannol. Pseudorabies virus (PRV) belongs to the family Herpesviridae. PRV has a wide host range and can cause cytopathic effects (CPEs) in PK-15 cells. Therefore, PRV was used as a model to study the antiherpesvirus effect of piceatannol. In this study, we evaluated the antiviral activity of piceatannol against PRV in vitro and in vivo. The results showed that piceatannol could reatrain PRV multiplication in PK-15 cells in a dose-dependent manner. The 50% inhibitory concentration (IC50) was 0.0307 mg/mL, the IC50 was 0.0307 mg/mL, and the selectivity index (SI, CC50/IC50) was 3.68. The addition of piceatannol at different stages of PRV infection inhibited the viral adsorption and intracellular replication phases of PRV. Piceatannol significantly reduced the expression levels of the IE180, EP0, UL29, UL44, US6 and UL27 genes of PRV within 48 h, significantly reduced the expression levels of the PRV gB and gD proteins, and reduced PRV-induced apoptosis. Molecular docking showed that piceatannol had good binding activity with the PRV gB and gD proteins. The results of animal experiments in vitro indicated that piceatannol could delay the onset of disease, improve the survival rate of the mice (14.3%), reduce the viral load in the brain and kidney of the mice, alleviate the pathological changes in the mouse tissues and organs, and increase the levels of TNF-α, IEN-γ and IL-4 in the serum of the mice. These data indicate that piceatannol has good anti-PRV activity in vitro and in vivo, indicating that it could be a novel antiherpesvirus infection agent in the future.

Brassica yellows virus (BrYV) is a tentative species of the genus Polerovirus, which occurs widely and mostly damage Brassicaceae plants in East Asia. Since BrYV could not be transmitted mechanically, an insect transmission method is required for further virus research. Here, a reliable and unrestricted method was described, in which non-viruliferous aphids (Myzus persicae) acquired BrYV from transgenic Arabidopsis thaliana plants with virus full length genome germinated from seeds and frozen infected leaves were used to transmit the virus to healthy plants, and there was no significant difference in acquisition rate though transmission rate from frozen infected leaves was somehow lower compared to fresh infected leaves. This novel simple method could be applied to preservation of virus inocula, evaluation of variety resistance to BrYV, biological research on interaction among BrYV, aphid and host, which also provide a new idea on establishing a basic method using virus genomic transgenic plants or frozen infected leaves for other poleroviruses research.

To explore the relevant factors that affect the efficacy of consciousness-regaining therapy (CRT)for prolonged disorder of consciousness(pDOC),a retrospective analysis was conducted on the case data of 114 patients with pDOC admitted to department of functional neurosurgery of Tianjin Huanhu Hospital from January 2019 to January 2022. Basic information on the cases,data on pDOC disease assessment, consciousness-regaining therapy methods, and efficacy evaluation were collected. A total of 114 patients were grouped and compared based on the efficacy at the end of treatment. Among them, there were 61 cases in the ineffective group and 53 cases in the effective group. There was no statistically significant difference (P>0.05) between the two groups in terms of gender, age, etiology, acute cerebral herniation, emergency craniotomy surgery, emergency decompressive craniectomy, time from onset to start of consciousness-regaining therapy , and duration of consciousness-regaining therapy(P>0.05). However, there were statistically significant differences (P<0.05) in terms of secondary hydrocephalus, , consciousness-regaining therapy methods, CRS-R grading before treatment, and GOSE score at 6 months after treatment. Binary logistic regression analysis showed that the type of therapy (OR=0.169, 95% CI: 0.057-0.508) was a related factor affecting the efficacy of consciousness-regaining therapy (P<0.05).Compared with non-invasive therapy, personalized awakening therapy using various invasive consciousness-regaining therapy methods can help improve the efficacy of therapy for pDOC.

China is rich in coal resources under water bodies. However, for a long time, the safety prediction of high-intensity mining under water bodies is one of the problems encountered by the coal industry. It is of great significance to realize safe mining under water bodies, improve the recovery rate of coal resources and protect reservoir resources. Therefore, this article takes the No. 5 coal seam and No. 11 mining area of Wangwa Coal Mine as the research object, and integrates physical simulation, numerical simulation, theoretical analysis and other methods to study the development height of water-conducting fracture zones in fully mechanized top coal caving mining. Solid-liquid coupling physical simulation test reveals the failure characteristics of overlying strata in goaf and the seepage law of reservoir water under the influence of mining. By comparing the monitoring data of borehole leakage, the measured data obtained by borehole peeping with the height data of water-conducting fracture zone obtained by the traditional empirical formula of three-under standard, the error between the two is as high as -29.39 %. In this case, the variance correction coefficient is used to correct the empirical formula, and on this basis, in order to effectively protect the surface water dam and water body, the mining height of coal seam in the working face with limited height mining is inversely derived. The research results provide a basis for the safety prediction of high-intensity mining under the reservoir dam in the ecologically fragile areas of western China and provide a scientific guarantee for the formulation of safety measures under such conditions.

Graphene-based composites have been widely explored for electrode and electrocatalyst materials for electrochemical energy systems. In this paper, a novel composite material of the reduced graphene oxide nanosheets (rGON) with gold nanoparticles (NPs) (rGON-AuNP) is synthesized, and its morphology, structure and composition are characterized by SEM, HRTEM, XRD, EDX, FTIR, Raman, and UV-Vis techniques. To confirm this material’s electrochemical activity, a glucose oxidase (GOD) is chosen as the target reagent to modify the rGON-AuNP layer to form GOD/rGON-AuNP/glassy carbon (GC) electrode. Two pairs of distinguishable redox peaks, corresponding to the redox processes of two different conformational GOD on AuNP, are observed on the cyclic voltammograms of GOD/rGON-AuNP/GC electrode. Both cyclic voltammetry and electrochemical impedance spectroscopy are employed to study the mechanism of direct electron transfer from GOD to GC electrode on the rGON-AuNP layer. In addition, this GOD/rGON-AuNP/GC electrode shows catalytic activity toward glucose oxidation reaction.

The study aims to analyze the characteristic parameters of rooftop photovoltaic (PV) power generation on industrial plant buildings in the Ningxia region of China, in order to evaluate the impact of passive design characteristic parameters on the benefits of PV power generation and determine the degree of impact of different passive design characteristic parameters. The methodology involves analyzing the characteristics of existing industrial plant buildings in Ningxia, China, and conducting a series of regional studies on the parameters of plant PV power generation influencing factors. The simulation results revealed that five features, including roof form, PV panel laying pattern, PV panel laying area, azimuth angle, and PV module material, have a significant impact on PV power generation benefits of industrial plant buildings.The study further uses MATLAB 2022b to build a backpropagation neural network model with 5 neurons in the implicit layer to predict the PV power generation benefits. The model calculates the whole-life cycle power generation benefits and the whole-life cycle reduction of carbon emissions as output data. Finally, the Mean Impact Value (MIV) method is employed to select the feature parameter values one by one within their range, and the passive design feature parameters that have the greatest influence on the prediction results are identified as the PV panel laying method, the PV panel tilt angle, and the PV material parameters, respectively.

Since the implementation of the Materials Genome Project by the Obama administration in the United States, the development of various computational materials databases has fundamentally expanded the choices of industries such as materials and energy. In the field of thermoelectric materials, the thermoelectric figure of merit ZT quantifies the performance of the material. From the viewpoint of calculations for vast materials, the ZT values are not easily obtained due to their computational complexity. Here, we show how to build a database of thermoelectric materials based on first-principles calculations for the electronic and heat transport of materials. Firstly, the initial structures are classified according to the values of bandgap and other basic properties using the clustering algorithm K-means in machine learning, and high-throughput first principles calculations are carried out for narrow-bandgap semiconductors which exhibiting potential thermoelectric application. The present framework of calculations mainly includes deformation potential module, electrical transport performance module, mechanical and thermodynamic properties module. We have also set up a search webpage for the calculated database of thermoelectric materials, providing searching and viewing the related physical properties of materials. Our work may inspire the construction of more computational databases of first-principle thermoelectric materials and accelerate research progress in the field of thermoelectrics.

The fault diagnosis of the gearbox is primarily based on the analysis of the harmonic response. However, the generation mechanism of the harmonic response of the gear pair is still not distinctly explained in a healthy gearbox. Therefore, this paper is dedicated to establishing a dynamic model of the gearbox for this issue. In this model, the contact force of the bearing and the meshing stiffness of the gear pair are determined by the Hertz theory and the potential energy method, then the shaft motion is used as the connection to establish the coupling relationship between the gear pair and the bearing. After this dynamic model is confirmed by experiments and existing models, the coupling relationship inside the gearbox and the harmonic response of the gear pair are studied using this model. The result demonstrates that a closed control loop is formed due to the vibration transmission between the gear pair, the bearing and the shaft, and there is a strong coupled vibration between the gear pair and the bearing in the gearbox. Due to the generation of the center distance error, misalignment angle and disorganized meshing process of the gear pair, the meshing stiffness is altered, which excites the harmonic response of the gear pair. When the speed of the gearbox is increased, although the vibration amplitude of the gearbox is increased, the system predominantly vibrates at the fundamental frequency, and the harmonic of the gear pair is also shifted to the low frequency band.

This study investigated the fatigue properties and interfacial strengthening mechanisms of Al6061-to-Cu dissimilar welded joints via electromagnetic pulse welding (EMPW). The load-bearing capacity of the joints at discharge voltages of 14 kV and 16 kV was superior to that of 12 kV. Meanwhile, the fatigue life of 14 kV joints was one order of magnitude higher than that of 12 kV. The SEM observation on the fatigue fracture surface shows that the typical “tire-mark” fatigue striation just appeared on the 14 kV joint, indicating higher ductility for handling more extended plastic deformation. The high EBSD acquisition was achieved except for the transition zone due to the formation of ultra-fine nanocrystalline Al2Cu phase and amorphous phase, along with many dislocations. Dense low-angle grain boundaries (LAGBs) and refined grains are formed along the bonding interface. This indicates that severe plastic deformation induced dislocations to form the substructure in such an instant (40-60 μs) during the high-velocity collision. The interfacial strength is not only due to the continuous interfacial diffusion layer with a “wave-like” or “inverted hook-like” pattern but also benefits from refined grains along the interface and in the transition zone, as well as the hybrid amorphous-nanocrystalline microstructure, which strengthens the joint through increasing ductility induced by refined grains and regulating amorphous or nanocrystalline phases to affect the balance between strength and ductility of the Al/Cu joint.

It is always a difficult task to assign the peaks recorded from vibrational spectrum. Herein we explored a new pathway of density functional theory (DFT) simulation to present three kinds of spectra of ice XIV and can be referenced as inelastic neutron scattering (INS), IR, and Raman experimental spectrum. The INS spectrum is proportional to phonon density of states (PDOS) while the photon scattering signals reflect the normal vibration frequencies near the Brillouin zone (BZ) center. Based on good agreements with experimental data, we identified the relative frequency and made scientific assignments by normal vibration modes analysis. The debating two hydrogen bond (H-bond) peaks among ice phases from INS have been discussed and the dynamic process of H-bond vibrations were found to be classified into two basic modes. we deduce that two H-bond modes are a general rule among ice family and more works are ongoing to investigate this subject.

The diamagnetic levitation technique can be applied to non-destructive testing for identifying cracks and defects in magnetic materials. Pyrolytic graphite is a material that can be leveraged in micromachines due to its no-power diamagnetic levitation on a permanent magnet (PM) array. However, the damping force applied to pyrolytic graphite prevents it from maintaining con-tinuous motion along the PM array. This paper investigates the in-plane motion and damping characteristics of pyrolytic graphite sheets on the PM array. The centroid of pyrolytic graphite will maintain a stable levitation when positioned on the intersecting point of the PM array. Fur-thermore, the in-plane motion of two different pyrolytic graphite sizes - PG10 (10×10×0.5mm3) and PG20 (20×20×0.5mm3) - has revealed that the in-plane forces applied to them are approximately 61.4μN and 28.2μN, respectively. The smaller sheet has a shorter oscillation time while oscillating before it stabilizes. The damping ratio of the oscillation was between 0.1-0.2. The in-plane force and the stable time of pyrolytic graphite are related to its size ratio in comparison with the PM. This relationship is believed to promote stability, as the force acting on the graphite sheet will be distributed over a larger area when the sheet size increases. During the fixed-axis rotation process, the study found that the friction coefficient and friction force decreased as the rotational speed decreased. The diamagnetic levitation of pyrolytic diamagnetic levitation is also unable to maintain long-term axial rotation. Finally, friction force was tested using PG10 during fixed-axis rotation above a circular PM array. The results showed that the order of the friction coefficient is 10-3, and the friction force is about 0.8μN, decreasing with graphite rotation speed. We hope this technique will be used in crack detection, magnetic detection and other micromachine.

Glaciation and mountain orogeny have generated new ecologic opportunities for plants, favoring an increase in the speciation rate. Moreover, they also act as corridors or barriers for plant lineages and populations. High genetic diversity ensures that species are able to survive and adapt. Gene flow is one of the most important determinants of the genetic diversity and structure of out-crossed species, and it is easily affected by biotic and abiotic factors. The aim of this study was to characterize the genetic diversity and structure of an alpine species, Festuca ovina L., in Xingjiang, China. A total of 100 individuals from 10 populations were analyzed using six amplified fragment length polymorphism (AFLP) primer pairs. A total of 583 clear bands were generated, of which 392 were polymorphic; thus, the percentage of polymorphic bands (PPB) was 67.24%. The total and average genetic diversities were 0.2722 and 0.2006 (0.1686-0.2225), respectively. The unweighted group method with arithmetic mean (UPGMA) tree, principal coordinates analysis (PCoA) and STRUCTURE analyses revealed that these populations or individuals could be clustered into two groups. The analysis of molecular variance analysis (AMOVA) suggested that most of the genetic variance existed within a population, and the genetic differentiation (Fst) among populations was 20.71%. The Shannon differentiation coefficient (G’st) among populations was 0.2350. Limited gene flow (Nm = 0.9571) was detected across all sampling sites. The Fst and Nm presented at different levels under the genetic barriers due to fragmentation. The population genetic diversity was significant relative to environmental factors such as temperature, altitude and precipitation.

Dredging is a common technique for managing eutrophication problems in waters, reducing the accumulation of pollutants by removing sediments from the bottom of water bodies. However, dredging can cause complex impacts on lake ecosystems, and it is crucial to understand benefits and mechanisms for environments. In this paper, the dredged and undredged areas in the Caohai portion of Dianchi Lake were studied to analyze the effects of dredging on nitrogen-phosphorus transport and conversion and changes in nitrogen-phosphorus morphology content and its mechanisms by comparing the nitrogen-phosphorus morphology content, percentage; nitro-gen-phosphorus ratio, and release contribution of the two areas. It was found that the ratio of sta-bilized nitrogen (SN) to stabilized phosphorus (SP) in the dredged area was lower than that in the non-dredged area; the BD-P and TOC contents had a large turnaround at the 16-20 cm position of the sediment in the dredged area; and the main conclusions were that the dredging would disrupt the internal equilibrium of the lake system for many years, and in particular, it would have the greatest effect on the balance of the BD-P in the phosphorus forms of the sediment, and that the column cores of the dredged area from 0 to 16 cm might be newly accumulated sediments after the dredging project. However, with time, the distribution of nitrogen and phosphorus forms in the newly accumulated sediments will gradually reach a new equilibrium. In addition, dredging will also cause significant changes in the retention efficiency of nitrogen and phosphorus in the sediment, and the stable nitrogen and phosphorus forms will be released and transformed into unstable ni-trogen and phosphorus forms.

We investigated and quantified soil organic carbon (SOC) stock at the mangrove forest (Magyi, That Bot Khan and Wette) of Shwe Thaung Yan coastal region in Myanmar and estimated the SOC stock changes in Magyi mangrove forest over six years using repeated field measurements. The study sites were characterized by different mangrove vegetation, soil types, and sediment deposition from different water sources. Results showed that the mangrove preservation and restoration efforts had a significant effect on soil C storage, with soil carbon stocks in 2021 (1954.43 ± 33.24 ton/ha) being 2.7 times higher than the estimated carbon stock in 2015 (732.26 ± 6.99 ton/ha). The results also revealed slight differences in SOC between Magyi and the Tha-Bot-Khan and Wette areas, as the mangrove plants in the latter areas have an additional source of nutrients from Pho-Thoung-Gyi, a deep-sea bay near the forest. Our research findings are beneficial in understanding the role of Myanmar’s mangrove ecosystems in carbon sequestration and climate change mitigation efforts.

Hydrogel antibacterial agent is an ideal antibacterial material because of it could diffuses antibacterial molecules into the decayed area by providing a suitable microenvironment and the hydrogel acts as a protective barrier on the decay interface. The biocompatibility and biodegradation make the removal process easily which were widely used in medical fields. However, there have been few reports on its application for controlling postharvest diseases in fruit. In this study, the Chitosan-Ag (CS-Ag) complex hydrogels were prepared using the physical crosslinking method, which used for controlling postharvest diseases in grape. The prepared hydrogels were stable for a long period at room temperature. The structure and surface morphology of CS-Ag composite hydrogels were characterized by UV-Vis, FTIR, SEM, and XRD. The inhibitory effects of CS-Ag hydrogel on disease in grape caused by P. expansum, A. niger and B. cinerea were investigated both in vivo and in vitro. The remarkable antibacterial activity of CS-Ag hydrogels was mainly due to the synergistic antibacterial and antioxidant effects of CS and Ag. Preservation test showed that the CS-Ag hydrogel had positive fresh-keeping effect. This revealed CS-Ag hydrogels plays a critical role in controlling fungal disease in grape.

Chalcones are a class of flavonoids possessing a variety of biological activities, including antimicrobial and antioxidant effects. Therefore, chalcones and their derivatives have potential use in the control of postharvest diseases. In this work, the effects of 2ʹ,4ʹ-dichloro-chalcone on the in vitro growth and in vivo pathogenicity of F. tricinctum and T. roseum were investigated. The results showed that 100 µM of 2ʹ,4ʹ-dichloro-chalcone strongly inhibited mycelial growth and conidial production of F. tricinctum (32.3%) and T. roseum (65.2%) in vitro. This treatment also significantly inhibited the expansion of potato dry rot from F. tricinctum (48.6%) and apple rot spot from T. roseum (36.2%). The incubation of F. tricinctum and T. roseum conidia with this agent for 2 h increased their cell membrane permeability by 25% and 22.5%, respectively and conidial membrane permeability by 41.7 and 65.4%, respectively. This treatment also significantly inhibited the total respiration rate and activated the cyanide-resistant respiratory pathway in both pathogens. Protein immunoblotting showed that the treatment increased alternative oxidase (AOX) levels after 4 h in F. tricinctum and T. roseum by 52.76% and 39.13%, respectively. Conclusion: 100 µM 2ʹ,4ʹ-dichloro-chalcone significantly inhibited mycelial growth and spore production in F. tricinctum and T. roseum in vitro and reduced their pathogenicity in postharvest potato and apple crops. Further analysis indicated that 2ʹ,4ʹ-dichloro-chalcone disrupted the integrity of cell membranes and the mitochondrial respiratory electron transport chain which leaded to ROS burst and oxidative stress, AOXs were induced directly or indirectly, and the cyanide resistant respiratory pathway was activated. The in vitro growth and pathogenicity of F. tricinctum and T. roseum were inhibited.

Spacecraft recovery technology is crucial in the field of aerospace, in which the parachute plays a key role in slowing down the descent speed of the spacecraft and realizing a smooth landing. In order to construct a dynamically adjustable parachute deployment strategy, it is necessary to measure the parachute dynamic load accurately in real time. However, the existing sensor measurement scheme is difficult to meet the measurement requirements due to its large structure and complex wiring. In order to meet the current demand for real-time measurement of parachute cords dynamic load, a miniature measuring instrument is designed.According to the function and technical requirements of the miniature measuring instrument, the hardware modules of the acquisition system are selected and designed, and the integration debugging and performance optimization of the microcontroller module, A/D sampling module, signal acquisition circuit and power supply module are carried out. The software of the parachute cords tension acquisition system based on the miniature measuring instrument is developed. The elastomer is modeled by using SolidWorks and statically analyzed by using AnsysWorkbench finite element analysis software. Then the final structure of the elastomer and the pasting position of the strain gage are determined through the results analysis as well as experimental verification. The hardware module of the signal acquisition system for the miniature measuring instrument is then encapsulated. The force value of the miniature measuring instrument is calibrated and tested many times by using the microcomputer-controlled electronic universal testing machine. The experimental results show that the designed miniature measuring instrument has accurate data, strong stability and good real-time performance, which meets the demand for real-time accurate measurement of miniature measuring instrument, and can provide reliable data for parachute cords parameter validation and stepless unfolding design.

The theory of electron spin has been proposed for a century, but the study of quantum effects in biological molecules is still in its infancy. Chirality-induced spin selectivity (CISS) is a very modern theory that can explain many biochemical phenomena. In this paper, we propose a new theoretical model based on CISS theory and quantum chemistry theory, which can well explain the theoretical explanation of the chiral selectivity of chiral proteins. Moreover, this theory can predict the spin state of corresponding chiral molecules. Taking L-DOPA and AADC enzyme as examples, this theoretical model solves the theoretical explanation of AADC enzyme's chiral catalysis selectivity problem and successfully predicts the spin state of L-DOPA and D-DOPA's valence electrons.

Potato tubers are susceptible to wounding during post-harvest processes, leading to quality decline, perishability and large economic losses. In this study, the potato cultivar, ‘Longshu No.7’, was foliar-sprayed with 3% chitosan (w/v) three times during the pre-harvest period after flowering to evaluate the effect of foliar spraying with chitosan on suberization processing at wounds of harvested potato tubers. Our results demonstrate that foliar-sprayed with chitosan significantly reduced wound-induced fresh weight loss and dry rot disease index by 37.34% and 41.60% on the 28 day after wounding, respectively. Foliar-sprayed with chitosan accelerated the deposition of suberin polyphenolics and lignin at the wound sites of potato tubers with the formation of thicker cell layers. This occurred with increased localized activities of key enzymes in the suberin polyphenolics and lignin pathways, including phenylalanine ammonia lyase, 4-coumaryl-coenzyme A ligase, cinnamyl alcohol dehydrogenase and peroxidase (33.90–64.32%), as well as the contents of cinnamic acid, sinapic acid, flavonoids, lignins and total phenolics (19.70–23.46%) at wound sites of potato tubers on the 7 day after wounding. Our results indicated that foliar application of chitosan accelerated wound-induced suberization of potato tubers and could mitigate post-harvest product damages.

Heart regeneration after myocardial infarction remains challenging in reconstruction of blood resupply system. Here, we find that in zebrafish heart after resection of the ventricular apex, the local myocardial cells and the clotted blood cells undergo cell remodeling process via cytoplasmic exocytosis and nuclear reorganization within revascularization-based blastema. The regenerative processes are visualized by spatiotemporal expression of three blastema representative factors (alpha-SMA- which marks for fibrogenesis, Flk1for angiogenesis/hematopoiesis, and Pax3a for remusculogensis)，and two histone modifications (H3K9Ac and H3K9Me3 mark for chromatin remodeling). Using the cultured zebrafish embryonic fibroblasts we identify blastema fraction components and show that Krt5 peptide could link cytoskeleton network and BMP4 signaling pathway to regulate the transcription and chromatin accessibility at the blastema representative genes and bmp4 genes. Our study provides new mechanistic insights into the epithelial-dependent and revascularization-based blastema regeneration for potential myocardial infarction therapy.

We report herein high-resolution x-ray diffraction measurements of basal plane bending of homoepitaxial single-crystal diamond (SCD). The results reveal that growth parameters such as temperature, growth time and basal plane bending of the substrate affect the basal plane bending of SCD. First, the basal plane bending of SCD depends mainly on the substrate itself. The basal plane bending of SCD becomes more severe with increasing basal plane bending of the substrate and this type of basal plane bending cannot be recovered. The SCD growth experiments show that the basal plane bending increases at high temperature and with increasing growth time. Finally, to understand the mechanism behind basal plane bending, we investigate the substrate-surface temperature distribution as a function of basal plane bending of SCD fabricated by chemical vapour deposition (CVD). This allows us to propose a bending model and understand the origin of basal plane bending. The results indicate that an uneven temperature distribution on the substrate surface is the main cause of the CVD diamond base-plane bending.

Cardiovascular disease (CVD) places a heavy burden on older patients and the global healthcare system. A large body of evidence suggests that exercise training is essential in preventing and treating cardiovascular disease, but the underlying mechanisms are not well understood. Here, we used the Drosophila melanogaster animal model to study the effects of early-life exercise training (ELET) on the aging heart and lifespan. We found in flies that age-induced arrhythmias are conserved across different genetic backgrounds. The fat body is the primary source of circulating lipoproteins in flies. Inhibition of fat body apoLpp (the flies apoB homolog) demonstrated that low expression of apoLpp reduced the development of arrhythmias in aged flies but did not affect average lifespan. At the same time, ELET can also reduce the expression of apoLpp mRNA in aged flies and have a protective effect on the heart, which is similar to the inhibition of apoLpp mRNA. Although treatment of apoLppRNAi and ELET alone had no significant effect on lifespan, the combination of apoLppRNAi and ELET extended the average lifespan of flies. Therefore, we conclude that apoLppRNAi and ELET are sufficient to resist age-induced arrhythmias, which may be related to the decreased expression of apoLpp mRNA, and that apoLppRNAi and ELET have a combined effect on prolonging the average lifespan.

Elevation has been a cornerstone of biodiversity research, and changes in the environmental factors behind it influence biodiversity and community patterns. Exploring the potential reasons behind liverwort community patterns has been a matter of multiplied interest for ecologists. In the present study, we assessed the liverwort plants of the Sygera Mountain from 3100 m to 4500 m decaying wood, tree, soil, and rock using complex field surveys in 2017 and 2019, and investigated the effects of altitude and various climatic factors on the diversity and community composition of the Sygera Mountain. Also, we used including ANOVA, mixed effects modeling, NMDS, ANOSIM, and CCA, which helped to critically assess the liverwort diversity with respect to environmental variables. The results of the study showed a bimodal variation in the richness of liverwort communities with altitude, with peaks occurring at 3500 m and 4100 m. The variation with altitude was significant, with communities at 4100 m and 4300 m being associated with arid environments, and those at 3100 m and 3300 m favoring areas of higher mean annual temperatures and precipitation. Among the climatic factors, the variation in mean diurnal rang, precipitation, and annual temperature was found to be the determinant of liverwort communities. The results suggest that elevation and daily temperature fluctuations play a crucial role in the distribution and community structure formation of mountain liverwort plants. This study deepens our understanding of liverwort ecology and emphasizes the importance of climatic variables in determining plant community composition.

In an effort to enhance the efficiency and safety of open-pit mines, this study explores the optimization of end slope road parameters and slope structures, specifically focusing on unmanned driving lanes.A significant aspect of the study is the development of a truck trajectory offset model, which considers the different reaction times between automated sensors and human drivers in adapting to environmental changes. To test these concepts, the study uses numerical simulations to confirm the stability of the proposed end slope designs. Using Victory West Mine No. 1 as a case study, the research determines the optimized width for unmanned driving lanes and the maximum angle for safe steepening of end slopes. The findings indicate that the optimized unmanned lane width for NTE240 mining dump trucks is 1743 mm, allowing for a 2-degree increase in the slope angle at the south end slope. This optimization leads to a steep mining stripping volume of 3.2735 million m³ and a coal output of 2.49628 million tons, maintaining a stripping ratio of 1.31m³/t. These results demonstrate that the unmanned driving road width optimization not only ensures slope safety but also significantly boosts the economic benefits of steep mining in open-pit mines.

The COVID-19 pandemic measures have negatively impacted education worldwide via travel restrictions, student visas, and physical attendanc,e among many other fac-tors. As one of the first places to impose strict pandemic measures and one of the last places to lift the measures, Mainland China provided a unique venue to investigate the effect of public health pandemic control policies on tertiary education. Considering the large portion of international students in medical schools and the higher susceptibility to the pandemic measures due to the natural synergy with teaching hospitals, medical schools can be an early forefront indicator of the impact of the pandemic on tertiary education. We surveyed 513 participants international medical students from Wen-zhou Medical University’s school of international studies in 2019 and 2022 about their satisfaction and demographic and cultural adaptation parameters. We found that the pandemic restrictions did not generally impact student satisfaction. Further analyzing the associated parameters, we found teaching satisfaction to be independent of age (P=.159), years in China (P=.896) and Chinese Level (P=.577) in the medical university. Teaching satisfaction is associated with the region of origin (P <0.001), acceptance of local social norms (P <0.001), satisfaction with the core values of Chinese culture (P <0.001), acclimatization to life in China (P <0.001), can easily make Chinese friends (P <0.001) among other factors. The findings of this study provide an understanding of the effects of pandemic measures on tertiary education satisfaction and other factors that can aid in international student satisfaction.

With an increase in energy consumption globally, Fischer-Tropsch (FT) synthesis is a good alternative for producing fuels and chemicals from coal, natural gas or biomass. Among them, coal to liquids has been put into production in countries that have large coal reserves. In this process, Fe-based catalysts are commonly used due to their earth abundance, comparatively wide operation range and ready availability to handle low H2/CO ratio from coal. Despite their extensive applications, the kinetic and mechanistic understandings of Fe carburization and FT reaction on Fe-carbides are relatively limited due to the complexity of phase composition of the applied catalysts. This review summarizes the current state of knowledge of FT synthesis on Fe-carbide with an emphasis on underlying mechanism. Specifically, the employment of model catalyst, such as Raney-Fe, could provide a convenient way to furnish kinetic information regarding Fe carburization and subsequent FT reaction. A major challenge for further understanding catalytic reactions occurring at the Fe-carbide surface is correlating FT activity and selectivity to specific active site. To address this issue, the advancements of both DFT calculations and surface science techniques are highly demanded.

Often, engineers with machining experience often judge machining state and tool life according to chips’ features. Engineers' experience is digitized in this study. During the cutting process, the cutting tool coming in contact with the workpiece produces a shear zone, which causes plastic deformation and shear slip. The chips closest to the shear zone can directly show the state of the tool and workpiece when the material is SKD61. This study used chip color, vibration, and current signal integration for prediction of machining state and cutting tool life. When the cutting tool wears increased, the chip surface color changed in the following way: purpleè purple blueè blue ècyan, or even green and yellow. When the cutting tool was in the accelerating wear phase, the color change was particularly obvious. The Back-Propagation Levenberg–Marquardt (BP-LM) predictive methodology was used to compare the predictive ability of voltage, vibration signal, and chip color. The Mean Absolute Percentage Error (MAPE) for the voltage signal was 12.28%, for the vibration signal it was 11.38%, and for the chip color combined with multi-sensor characteristics it was 7.85%. The MAPE of the chip color was the smallest. Using the General Regression Neural Network (GRNN) methodology, the MAPE for the voltage signal was 10.74%, for the vibration signal 7.96%, and for the chip color combined with multi-sensor characteristics was 6.59%. The MAPE of the chip color was the smallest. Obviously, the chip color combined with multi-sensor signals provided better predictive results than the vibration signal or voltage signal alone. There is currently no research on the usefulness of monitoring chip color for tool life prediction.

Broad bean paste (BBP) is a traditional fermented soy food, and its high salt content not only prolongs the fermentation time but also threatens human health. In this study, three BBP-meju with different salt concentrations were prepared, and the effects of varying salinity on the fermentation process were comprehensively compared. The results showed that salt-reduced fermentation contributed to the accumulation of amino acid nitrogen, reducing sugars, free amino acids, and organic acids. Alcohols, esters, aldehydes, and acids were the main volatile flavor compounds in BBP-meju, and the highest total volatile flavor compounds were found in medium-salt meju. Bacillus, Staphylococcus, Aspergillus, and Mortierella were the dominant microbial communities during fermentation, and there were also three opportunistic pathogens, Enterobacter, Pantoea, and Brevundimonas, respectively. According to Spearman correlation analysis, Wickerhamomyces, Bacillus, Staphylococcus, and Mortierella all showed highly significant positive correlations with ≥3 key flavor compounds, which may be the core functional flora. Furthermore, the dominant microbial genera worked synergistically to promote the formation of high-quality flavor compounds and inhibit the production of off-flavors during salt-reduced fermentation. This study provides a theoretical reference for the quality and safety control of low-salt fermented soy foods.

The state of the grinding wheel in the grinding process directly affects the surface quality of the workpiece. The monitoring of the wear state of the grinding wheel can effectively identify the wear information of the grinding wheel and timely and effectively repair the grinding wheel. In this paper, a multi-sensor fusion precision grinding wheel wear intelligent monitoring system is established for typical difficult-to-machine aerospace material titanium alloy, and a multi-eigenvalue fusion algorithm based on improved support vector machine (SVM) is proposed. The extracted sound emission signal wavelet packet decomposition coefficient mean square value, force signal grinding force ratio, and vibration signal effective value are used as the input of the improved support vector machine, and the identification strategy is adjusted by the entropy weight evaluation method. The results show that the monitoring system established in this paper can effectively identify the wear state of the grinding wheel, and the monitoring accuracy can reach more than 92%.

The nucleation of voids in alpha iron and the influence of carbon were investigated through a combination of rate theory and nucleation theory calculations. The steady rates of void nucleation exhibit high sensitivity to carbon. Even a seemingly negligible carbon concentration, as low as a few atomic parts per million (appm), can dramatically reduce the nucleation rates and narrow the temperature window for nucleation. This study highlights the challenges in certifying and qualifying nuclear materials for use in reactor environments. It emphasizes the necessity for precise control of impurity levels during materials processing and stringent requirements for irradiation testing, which are susceptible to contamination. Furthermore, the study provides an explanation for the significant data scattering observed in void swelling behaviors as reported in the literature.

In the mold machining process, the cutting tool is worn with machining time, thereby affecting the surface accuracy, leading to poor workpiece dimensions, even fracture. At present, many studies have used multiple sensors to detect the machining conditions of cutting tool and workpiece, including indirect measurement method and direct measurement method. The indirect measurement method, which has been studied widely, mainly uses sensors to capture signals for subsequent data analysis; the direct measurement method mainly analyzes the state of cutting shear zone. Due to the cut-in of cutting tool in the machining process, the workpiece is dislocated rapidly, generating considerable amount of heat, which is transferred to the chips, inducing color change on the surface of chips. Many engineers with machining experience often judge the machining state and tool life according to the chips. The engineers' experience is digitized in this study, and indirect measuring sensors are used to predict the tool life, so as to attain the objective for smart manufacturing, the average percentage error of MAPE using single vibration and voltage eigenvalues as input features is 10%, the voltage signal characteristic values and vibration signal characteristic values are combined. Finally, the chip surface chromaticity eigenvalue is combined with signal characteristic value. The average prediction error of BP-LM method is 7.85%, the average prediction error of GRNN method is 6.59%. Therefore, when the eigenvalue of chip surface chromaticity is added to the prediction result, it can enhance the accuracy of cutting tool wear value prediction more effectively than single sensor signal characteristic value.

The microglia, displaying diverse phenotypes, play a significant regulatory role in the development, progression, and prognosis of Parkinson's disease. Research has established that glycolytic reprogramming serves as a critical regulator of inflammation initiation in pro-inflammatory macrophages. Furthermore, the modulation of glycolytic reprogramming has the potential to reverse the polarized state of these macrophages. Previous studies have shown that levetistilide A (LA), a phthalide component derived from Angelica sinensis, possesses a range of pharmacological effects, including anti-inflammatory, antioxidant, and neuroprotective properties. In our study, we have examined the impact of LA on inflammatory cytokines and glucose metabolism in microglia induced by lipopolysaccharide (LPS). Furthermore, we explored the effects of LA on the AMPK/mTOR pathway and assessed its neuroprotective potential both in vitro and in vivo. The findings revealed that LA notably diminished the expression of M1 pro-inflammatory factors induced by LPS in microglia, while leaving M2 anti-inflammatory factor expression unaltered. Additionally, it reduced ROS production and suppressed IκB-α phosphorylation levels as well as NF-κB p65 nuclear translocation. Notably, LA exhibited the ability to reverse microglial glucose metabolism reprogramming and modulate the phosphorylation levels of AMPK/mTOR. In vivo experiments further corroborated these findings, demonstrating that LA mitigated the death of TH-positive dopaminergic neurons and reduced microglia activation in the ventral SNpc brain region of the midbrain and the striatum. In summary, LA exhibited neuroprotective benefits by modulating the polarization state of microglia and altering glucose metabolism, highlighting its therapeutic potential.

This study investigated the mechanical properties and fatigue behavior of FH36 steel plate rolled in different directions. By adopting a sequential rolling process in the rolling direction (RD) and transverse direction (TD), the differences in properties between RD and TD were eliminated, resulting in nearly identical tensile properties. The steel plate exhibited a yield strength of approximately 420 MPa, a tensile strength of approximately 506 MPa, and an elongation of approximately 25%. Fatigue tests conducted at room temperature and -60℃ showed a fatigue limit of the maximum stress of 488 MPa at room temperature and 500 MPa at -60℃, indicating improved low-temperature fatigue performance. The fracture surfaces displayed distinct characteristics, such as oblique shearing fractures for high-cycle fatigue and cup-cone shape fractures for low-cycle fatigue. The fatigue source zone were both on the surface of the specimens. As the maximum stress increased, the area of the crack propagation zone for high-cycle fatigue decreased, while the area of the final fracture zone, the number of dimples and the proportion of the LAGBs increased.

Shape Memory Alloy (SMA) have emerged as a revolutionary material that holds the potential to change the design and construction methods of buildings and other structures. One of the most promising applications of SMAs in civil engineering is their use as reinforcements for steel structures. This paper presents the latest research progress, opportunities and challenges of SMA in the field of steel structural reinforcement, both in terms of basic components and applications. In terms of components, the construction forms and working mechanisms of Fe-SMA strips, SMA/CFRP composite patches and SMA dampers are introduced. On this basis, the application of SMA in steel structures reinforcement is introduced, and its effect is analyzed from three aspects: crack restoration, seismic retrofitting and structural strengthening. Finally, the results of the current research are summarized and the shortcomings are analyzed, hoping to provide a reference for the research of SMA in the field of steel structures reinforcement.

Energy resources are important sources of social and economic development, human survival and security. However, energy resources are objective and scarce, especially the fossil energy, such as coal, oil, natural gas, etc. Human survival environment is increasingly damaged, and the condition of energy is also gradually becoming deficient, so it is necessary to develop new energy resources to meet the increasing demand of material civilization. Solar energy can meet the needs of human development in the future as a kind of clean resource and it has been concerned by all countries in the world. We analyzed the effectiveness of subsidies to the PV industry of both the price and R&D by the spatial econometric model. In some region, the production capacity of photovoltaic industry has shown a significant spatial agglomeration situation in China since 2012. At the same time, benchmarking price and R&D subsidies played a positive incentive to the photovoltaic industry production capacity. It is a certain degree of inverse correlation between the scale of policy subsidies and the resource endowment of solar resources. Therefore, the countermeasures should be considered from the aspects of institutions, industry, technology and public financial policies.

Although good field emission from graphene has been demonstrated from a wide variety of different microfabricated structures, very few of them can be used to improve the design of cold field emitters for electron microscopy applications. Most of them consist of densely packed nano-emitters, which produce a large array of defocused overlapping electron beams, and therefore cannot be subsequently focused down to a single nanometer electron probe. This paper reviews the kind of single-tip cathode structures suitable in cold field emission guns for instruments such as scanning electron microscopy, transmission electron microscope or scanning transmission electron microscopy, and reviews progress in fabricating them from graphene-based materials.

To be CMOS-compatible, a low preparation temperature (&lt; 500 °C) of ferroelectric films is required. In this study, BiFeO3 films were successfully fabricated at a low annealing temperature (&lt; 450 °C) on aluminum foils by a metal-organic decomposition process. The annealing atmosphere on performance of BiFeO3 films was assessed at 440 ± 5℃. By replacing an O2-rich atmosphere with an N2-rich one, a better crystalline morphology was achieved in BiFeO3 films, resulting in better electric properties targeted for high-density ferroelectric random-access memory applications. These properties included a large remnant polarization (Pr~78.1 μC/cm2 @ 1165.2 kV/cm) and a high rectangularity (~91.3% @ 1165.2 kV/cm) of the P-E loop, along with excellent charge-retaining ability up to 1.0 × 103 s and a fatigue resistance reaching 1.0 × 109 switching cycles. The enhanced performance of BiFeO3 film in an N2-rich atmosphere maybe originated from the slightly high content of oxygen vacancies during the annealing process. Furthermore, decent electrical properties (Pr~70 μC/cm2 @ 1118.1 kV/cm) of the BiFeO3 films were achieved at a very low annealing temperature of 365 ±5 °C on aluminum foil substrates. These results offer a new idea for lowering the annealing temperature for integrated ferroelectrics in high-density FeRAM applications.

Industrial process control systems commonly exhibit features of time-varying, strong coupling, and strong nonlinearity. Obtaining accurate mathematical models of these nonlinear systems and achieving satisfactory control performance is still a challenging task. In this paper, data-driven modeling techniques and deep learning methods are used to accurately capture a category of smooth nonlinear system’s spatiotemporal features. The operating point of these systems may change over time, and their nonlinear characteristics can be locally linearized. We established the LSTM-CNN-ARX model by utilizing a fusion of long short-term memory (LSTM) network and convolutional neural network (CNN) to fit the coefficients of the state-dependent exogenous variable autoregressive (SD-ARX) model. Compared to other models, the hybrid LSTM-CNN-ARX model is more effective in capturing the nonlinear system’s spatiotemporal characteristics due to its incorporating the strengths of LSTM for learning temporal characteristics and CNN for capturing spatial characteristics. The model-based predictive control (MPC) strategy, namely LSTM-CNN-ARX-MPC, is developed by utilizing the model's local linear and global nonlinear features. The control comparison experiments conducted on a water tank system (WTS) show the effectiveness of the developed models and MPC methods.

Hyperandrogenism and insulin resistance are co-pathologies of polycystic ovary syndrome (PCOS). Recent evidence has suggested that elevated local cortisol levels are associated with ovarian and endometrial insulin resistance in hyperandrogenic PCOS patients, but the molecular mechanisms underlying these clinical findings remain unclear. We and others have used chronic treatment with human chorionic gonadotropin (hCG) and insulin to create an in vivo rodent model for the onset and development of PCOS-like phenotypes. Here, we aimed to determine whether the molecular mechanisms of glucocorticoid receptor (GR) signaling, mitochondrial function, and local inflammation in the ovary and uterus are intrinsically different in PCOS-like rats compared to controls. In both the ovary and the uterus, decreased expression of two GR protein isoforms was concurrent with increased expression of Fkbp51 but not Fkbp52 mRNA in PCOS-like rats compared to controls. However, PCOS-like rats exhibited an opposite regulation of Hsd11b1 or Hsd11b2 mRNAs in the two tissues. Further, the expression of several oxidative phosphorylation-related protein components was decreased in the PCOS-like ovary and uterus, but surprisingly the expression of many genes involved in mitochondrial function and homeostasis was increased in the same tissues and animals. Additionally, PCOS-like rats showed the increased expression of ovarian and uterine NFκB signaling proteins and Tnfaip3 mRNA. In PCOS-like rats, while similar decreased expression of Il1b, Il6, and Mmp2 mRNAs was seen in the ovary and uterus, the opposite regulation of Tnfa, Ccl2, Ccl5, and Mmp3 mRNA expression was observed in the two tissues. Both ovaries and uteri from PCOS-like animals showed increased collagen deposition compared to controls. Collectively, our observations suggest that hyperandrogenism and insulin resistance disrupt ovarian and uterine GR activation and trigger compensatory or adaptive effects for mitochondrial homeostasis, allowing tissue-level maintenance of mitochondrial function in order to limit ovarian and uterine dysfunction. Our study also suggests that hyperandrogenism and insulin resistance-induced activation of NFκB signaling resulting in aberrant regulation of inflammation-related gene expression might be tissue specific in female reproductive tissues.

Introduction The Pericapsular Nerve Group (PENG) block is a novel technique that allows for analgesia of the anterior hip capsule via the articular branches of the accessory obturator nerve and femoral nerve, which have a significant role in the innervation of the hip capsule. PENG blockade is effective in both adult and pediatric patients. However, there are no studies in the available literature on patients under five years of age. Herein, we describe our experience with two pediatric patients with hip dysplasia. Purpose This study aimed to evaluate the analgesic effect of the pericapsular nerves group (PENG) in small children undergoing hip surgery. Patients and methods This study included two patients, aged 2 and 4 years old, who qualified for hip surgery. General or spinal anesthesia with the addition of a PENG block was performed. During the procedure, the basic hemodynamic parameters were monitored. After the surgery, the patients received 15mg/kg-1 iv paracetamol every 6 hours to prevent rebound pain. The pain was assessed using the FALCC score. The 15mg/kg-1 metamizole was administered if the FLACC score was 3. In the FLACC score 4, the application of 0,2mg/kg-1 Nalpain was ordered. Results The patient's hemodynamic parameters were stable and within normal range. FLACC scores from all patients ranged from 0 and 3 in the first 24 h period. One patient required metamizole 12 hours after surgery. No evidence of block complications was observed. Conclusions This case series showed that PENG block provided adequate postoperative analgesia and assured opioid-free pain management. However, we are convinced that future randomized, controlled trials are needed in this field.

Most of the mid-high permeability sandstone oilfields in China have entered the ultra-high water cut stage, accompanied with the highly-dispersed residual oil, and the control effect of mi-cro-heterogeneity on the residual oil is increasingly prominent. Understanding the microscopic characteristics of pore structural and its evolution during the long-term waterflooding is critical for enhancing the accuracy and efficiency of oil field exploitation. While the previous insights paid more attention to the geometrical and morphological features of pore structure and ignores the relation of pore structure with the fluid flow capacity. In this study, we propose a microscopic pore structure classification method considering pore size and local permeable capacity, which realizes the physical classification and quantitative evaluation of pore structure characteristics for different permeability rocks. The micro-pore structure is classified into 6 types based on the key evaluation parameters of pore diameter and flow flux area. By taking six mid-high permea-bility sandstone core samples from Daqing oilfield in China, a series of long-term waterflooding experiments are carried out and the interior pore structure was captured using high precision CT scanning technique. The results reveals that high-permeability reservoirs exhibit concentrated pores diameters and finer throats, whereas mid-permeability reservoirs exhibit smaller pores and throats in greater quantity. With the increase of water injection volumes, the permeable ca-pacity and connectivity of the high-connectivity pore space in ultra-high- and high-permeability reservoirs are enhanced, and in mid-permeability reservoirs, the micro-heterogeneity intensifies the increase in low-connectivity small pores. These findings provide new insights for the micro-scopic heterogeneity and a solid theoretical basis for investigating the occurrence of microscopic residual oil and optimising enhanced oil recovery strategies at the late stage of ultra-high water cut.

Tumor-associated macrophages (TAMs) play critical roles in the tumor microenvironment (TME), where they are recruited by signals released by cancer cells. Although they have great potential as therapeutic targets for cancer treatment, the dual roles of TAMs in promoting or inhibiting tumor growth, invasion, and metastasis make their function in cancer progression complex. In this review, we provide an overview of the current understanding of TAMs, including their phenotypic diversity, regulatory signaling pathways, and interactions with other cells in the TME. We also discuss the challenges related to the standard isolation protocols of TAMs, inconsistent research results, and translation of TAM knowledge into clinical applications. Additionally, we review the status of clinical trials involving TAMs and potential strategies to overcome the limitations. The future direction of TAM research should focus on developing more targeted therapies that specifically regulate TAM function and non-invasive methods for monitoring TAM activity in cancer patients. A comprehensive understanding of the complex role of TAMs in cancer may lead to the development of more effective treatments and improved outcomes for cancer patients.

We study L_2-approximation problems in the weighted Hilbert spaces in the worst case setting. Three interesting weighted Hilbert spaces appear in this paper, whose weights are equipped with two positive parameters $\ga_j$ and $\az_j$ for $j=1,\,2,\dots,\,d$. We consider the worst case error of algorithms that use finitely many arbitrary continuous linear functionals. We discuss the exponential convergence-(t,s)-weak tractability (EC-(t,s)-WT) of these L_2-approximation problems under the absolute or normalized error criterion. In particular, we obtain the sufficient and necessary conditions for EC-(1,1)-WT and EC-(t,1)-WT with t

The energy transfer process of laser selective melting is very complex. To study the effect of la-ser selective melting on the microstructure and properties of 18Ni-300 martensitic steel, ABAQUS was used to simulate the temperature of laser cladding 18Ni-300 martensitic steel at different time points and different laser power. The results show that the cross-section shape of the molten pool changes from round to oval With the increase of laser power, the higher the peak value of temperature time curve, the greater the temperature gradient; and the laser clad-ding experiment of 18Ni-300 martensitic steel was carried out, and the microstructure and me-chanical properties of the samples under different laser power were analyzed. The results show that with the increase of laser power, the grain size of the cladding layer becomes smaller and the microstructure becomes more compact; the hardness of the side surface of the sample is higher than that of the upper surface, and the tensile strength and elongation show a trend of first increasing and then decreasing.

In this paper, a class of nonlinear ordinary differential equations with impulses at variable times is considered. The existence and uniqueness of solution are given. At the same time, modifying the classical definitions of continuous dependence and Ga^teaux differentiability, some results on continuous dependence and Ga^teaux differentiable of solution relative to the initial value also are presented in new topology sense. For the autonomous impulsive system, the periodicity of solution is given. As an application, properties of solution for a type of controlled nonlinear ordinary differential equation with impulses at variable times is obtained. These results are foundation to study optimal control problems of systems governed by the differential equations with impulses at variable times.

Currently there are fewer depth models applied to pepper picking detection, while the existing generalized neural networks have problems such as large model parameters, long training time, and low model accuracy.In order to solve the above problems, this paper proposes a Yolo-chili target detection algorithm for chili pepper detection. First, the classical target detection algorithm yolov5 is used as a benchmark model, and an adaptive spatial feature pyramid structure combining the attention mechanism and the idea of multi-scale prediction is introduced to improve the model's detection effect on occluded peppers and small target peppers. Secondly, a three-channel attention mechanism module is introduced to improve the algorithm's long-distance recognition ability and reduce the interference of redundant testers. Finally, the quantized pruning method is used to reduce the model parameters and realize the lightweight processing of the model. Applying the method to the homemade chili pepper dataset, the AP value of chili pepper reaches 93.11%; the accuracy rate is 93.51% and the recall rate is 92.55%.The experimental results show that yolo-chili is able to achieve accurate and real-time pepper detection under complex orchards.

Using the Yellow-River-Source National Park (YRSNP) as a study site, an unmanned aerial vehicle (UAV) remote sensing and line transect method was used to investigate the number of wild herbivorous animals and livestock, including the kiang (Equus kiang) and Tibetan gazelle (Procapra picticaudata). A downscaling algorithm was used to generate the forage yield data in YRSNP based on 30 m spatial resolution. On this basis, we estimated the forage–livestock balance, which included both wild animals and livestock, and analyzed the effects of functional zone planning in national parks on the forage–livestock balance in YRSNP. The results showed that the estimates of large herbivore population numbers in YRSNP based on population density in the aerial sample strips, which were compared and validated with statistical data and warm season survey results, indicated that the number of kiangs and Tibetan gazelles in the 2017 cold season was 12900 and 12100, respectively. The number of domestic yaks, Tibetan sheep, and horses was 53400, 76800, and 800, respectively, and the total number of sheep units was 353200. The ratio of the number of large wild herbivores and livestock sheep units was 1:5; Large wild herbivores have different preferences for functional zones, preferring ecological restoration areas consisting mainly of degraded grassland; The grazing pressure indices of the core reserve areas and ecological restoration areas were 0.168 and 0.276, respectively, indicating that these two regions still have high grazing potential. However, the grazing pressure index of the traditional utilization areas was 1.754, indicating that these grasslands are severely overloaded; After the planning and implementation of functional zones, the grazing pressure index of YRSNP was 1.967. Under this measure, the number of livestock was not reduced and the grazing pressure nearly doubled, indicating that forage–livestock conflict has become more severe.

Paleopeat-forming environments have an important effect on the dispersion and enrichment of trace elements in coal. The C3 coal seam of the Xuanwei Formation in eastern Yunnan was used as a case study to reconstruct the paleopeat-forming environment based on the coal facies parameters and geochemical characteristics, and its influence on trace element (including rare earth elements and yttrium, REY) enrichment was investigated. The C3 coal was classified as medium rank coking coal with an ultra-low moisture content, medium-high-ash yield, and low-medium volatile content. Compared to the average values for Chinese coals, Cu and V were enriched and Co was slightly enriched in the C3 coal. Compared with the average values for world coals, Cu and V were enriched, while several other trace elements were slightly enriched, including Co, Hf, Nb, Sc, Ta, Zn, and Zr in the C3 coal. The C3 coal was deposited in a low peat mainly limno-telmatic swamp, with deep water, weak hydrodynamic conditions, brackish to salty water, and reducing conditions. Trace elements, including Cu, V, Hf, Nb, Sc, Ta, Zr, and REY, are typically enriched in a limno-telmatic environment with fresh water, and reducing and weak hydrodynamic conditions. Additionally, REY and V are also significantly enriched in brackish water limno-telmatic conditions with the same depositional environment.

In order to correct attenuated millimeter-wavelength (Ka-band) radar data and address the problem of instability, an attenuation correction methodology (attenuation correction with variation trend constraint; VTC) was developed. Using synchronous observation conditions and multi-band radars, the VTC method adopts the variation trends of reflectivity in X-band radar data captured with wavelet transform as a constraint to adjust reflectivity factors of millimeter-wavelength radar. The correction was evaluated by comparing reflectivities obtained by millimeter-wavelength cloud radar and X-band weather radar. Experiments showed that attenuation was a major contributory factor in the different reflectivities of the two radars when relatively intense echoes exist, and the attenuation correction developed in this study significantly improved data quality for millimeter-wavelength radar. Reflectivity differences between the two radars were reduced and reflectivity correlations were enhanced. Errors caused by attenuation were eliminated, while variation details in the reflectivity factors were retained. The VTC method is superior to the bin-by-bin method in terms of correction amplitude and can be used for attenuation correction of shorter wavelength radar assisted by longer wavelength radar data.

Two-dimensional (2D) ice I is an atomic-level ice that is composed of two interlocked atom-ic layers saturated with hydrogen bonds. It has recently been experimentally observed but its properties have yet to be clarified. Accordingly, we theoretically studied the hydrophobic properties of 2D ice I. On the contrary, simulation of a hydrogen fluoride molecule on a 2D ice surface manifested that it destroyed the 2d ice structure and connected new hydrogen bonds with water molecules. Investigations of the interfacial effect between 2D and three-dimensional (3D) ice films indicated that the network structure of 2D ice was not de-stroyed by a 3D ice surface, as the former was saturated with hydrogen bonds. However, the surface of 3D ice reorganized to form as many hydrogen bonds as possible. Thus, the 2D ice film was hydrophobic and inhibited the growth of 3D ice. This shows that if 2D ice can be produced on an industrial scale, it could be used as an anti-3D-icing agent under low tem-perature.

To explore the effects of pymetrozine on the reproductive behavior of N. lugens, we established a bioassay method to accurately evaluate the toxicity of pymetrozine in N. lugens and establish the level of pymetrozine resistance of N. lugens in the field. In this study, pymetrozine’s effects on the fecundity of N. lugens were evaluated using the topical application method and rice-seedling dipping method. Moreover, the resistance of N. lugens to pymetrozine in a pymetrozine-resistant strain (Pym-R) and two field populations (YZ21 and QS21) was determined using the rice-seedling dipping method and fecundity assay methods. The results showed that treatment of N. lugens third-instar nymphs with LC15, LC50, and LC85 doses of pymetrozine resulted in significantly reduced male fertility and female fecundity. In addition, N. lugens adults treated with pymetrozine using the rice-seedling dipping and topical application method also exhibited significantly in-hibited male courtship, fertility, and female receptivity. Using the rice-stem dipping method, pymetrozine resistance was shown to be at high levels in Pym-R (194.6-fold), YZ21 (205.9-fold), and QS21 (212.8-fold), with LC50 values of 522.520 mg/L (Pym-R), 552.962 mg/L (YZ21), and 571.315 (QS21) mg/L. However, when using the rice-seedling dipping or topical application fe-cundity assay method, Pym-R (EC50: 14.370 mg/L, RR=12.4-fold; ED50: 0.560 ng/adult, RR=10.8-fold), YZ21 (EC50: 12.890 mg/L, RR=11.2-fold; ED50: 0.280 ng/adult; RR=5.4-fold), and QS21 (EC50: 13.70 mg/L, RR=11.9-fold) exhibited moderate or low levels of resistance to pymet-rozine. Our studies show that pymetrozine can significantly inhibit the fecundity of N. lugens. The fecundity assay results showed that N. lugens only developed low to moderate levels of resistance to pymetrozine, indicating that pymetrozine can still achieve effective control on the next gen-eration of N. lugens populations.

The Yangtze River is cross-linked with numerous lakes within its floodplain and is a worldwide biodiversity hotspot. There is no evidence indicating when this unique river-lake system developed. The endemic East Asian cyprinid clade has evolved diverse spawning adaptations to different flow conditions. Our ancestral egg-type reconstruction showed an ancestral state of adhesive eggs and later demersal eggs origination (both stream adaptations). Semi-buoyant eggs emerged ~18 Mya as a fast-flowing river adaptation, with increased hydration via three yolk protein degradation pathways, ion transport pathways and egg envelope permeability transition pores. Adhesive eggs evolved secondarily ~14 Mya with the egg envelope increasing to four layers and an adhesive layer, along with an increase in adhesiveness via microfilament/adhesive-related protein crosslinking and enhanced glycosaminoglycan biosynthesis, improving adherence to submerged lake plants, indicating that the cross-linked river-lake system formed in the mid-Miocene. This study provides a unique biological evidence for large-scale water system evolution.

Background: Pittosporum tobira (Thunb.) Aiton is an aromatic medicinal plant widely cultivated in the world. However, the essential oils (EOs) from P. tobira flowers for anti-cancer potential is still not systematically studied. The present aim to elucidate the phytochemical composition of the EOs and to explore mechanism of anticancer action. Methods: The EOs were extracted and analyzed by headspace solid-phase microextraction (HS-SPME) with gas chromatography-mass spectrometry (GC-MS). Volatile components were identified according to Kovats retention index (KI) and NIST database. The anti-neoplasm mechanisms of the EOs was comprehensively investigated in lung carcinoma A549 and H460 cells. Results: A total of 47 secondary metabolites representing 94.18% of the EOs were successfully identified: monoterpenes and sesquiterpenes were the dominant terpenoids. The EOs exhibited antiproliferative activity on A549 and H460 lung carcinoma cells. Hoechst 33324 fluorescent staining indicated the typical characteristics of apoptosis and induced cycle phase arrest. AnnexinV/PI staining revealed that the number of apoptotic cells was increased. Furthermore, the EOs also induced the caspase-mediated mitochondrial apoptosis pathway. Conclusions: Findings suggest that the full-scale chemical composition and first characterization of anticancer activities of the EOs, it could be used for integrative natural anti-cancer agents in health care should be pay more attention.

Silicon carbide single crystal (SiC) has been widely used in the field of power devices, while it is difficult to fabricate ultra-flat surface by traditional manufacturing technologies due to its difficult-to-machine property. This paper investigates the interaction process during femtosecond laser ablation of crystalline silicon carbide based on the two-temperature model simulation and experimental study. The findings reveal that parameters such as laser pulse energy, scanning interval, and defocus amount exert significant influence on ablation depth, roughness, and surface morphology. The femtosecond laser proves effective in removing surface defects from cut SiC substrates, albeit resulting in increased surface roughness. However, subsequent polishing treatment of the laser-ablated silicon carbide surface can mitigate this roughness, underscoring the feasibility of laser surface ablation for silicon carbide single crystals.

JIS SUJ2 is most widely used in bearing steels. The advantages are good hardenability, excellent fatigue, wear resistance and comprehensive mechanical properties. For wear resistance and fatigue resistance of the steel are getting more and more attention, the residual stress state and its distribution on the surface of the heat affect zone are critical factors affecting the fatigue life and wear resistance of the parts. In this study, using the SUJ2 as the material to talk about the surface residual stress and retained austenite distribution. Doing the quenching and tempering treatment to obtain different microstructures, using the induction method to re-quench the case region. After the heat treatment, measuring the residual stress and retained austenite volume on the surface by X-ray diffraction, observing the microstructure and comparing the hardness. The results show that the microstructure after heat treatment contains unsolidified carbides, tempered martensite and retained austenite. The residual stress on the surface is the tensile state. In the re-hardened area after induction quenching, the residual stress is all compressive, and the values are more than -800 MPa. In conclusion, in the same output power condition can be observed that the microstructure of the specimens before induction hardening has a significant impact on the effective case depth. The surface residual stress has changed from a tensile to a compressive state. In the re-hardened area, the maximum of the residual compressive stress increased with the austenitized temperature increase.

The mechanical engineering requires heat treatment after rough machining to reach the mechanical strength, but the heat treatment can induce workpiece deformation, so that the workpiece cannot be reworked. In this study, the plasma was integrated with a lathe, and the on line heat treatment was performed to achieve the mechanical strength and hardness, so as to reduce the machining process and handling. However, for on line heat treatment, it is important to study the machine and plasma parameters of the lathe and plasma, and the research method is used eventually to optimize the process, reduce the machining cost and machining error. The variable factors in surface on line real-time heat treatment are revolution, feed rate and current, the objective function is the hardness of mechanical properties. In the screening experiment, the interaction of factors was discussed using full factorial experiment. The Central Composite Design was combined with the Lack-of-Fit test for optimization experiment, the R2 coefficient was used to determine whether the regression model is appropriate. The optimum parameters were derived from the contour diagram and response surface diagram. The experimental results show that the significant factors include revolution, feed rate and current, the optimum parameters include revolution 168rpm, feed rate 0.068mm/rev and current 86A. The experimental results of optimum parameters show that the surface hardness is increased from 306HLD to 806HLD, the surface hardening effect is enhanced by 163%, so the on line real-time heat treatment equipment has a best hardening effect.

Distributed deformation based on Fiber Bragg Grating sensors or other kinds of strain sensors can be used to evaluate safety in operating periods of bridges. However, most of the published researches about distributed deformation monitoring are focused on solid rectangular beam rather than box girder—a kind of typical hollow beam widely employed in actual bridges. Considering that the entire deformation of a single-cell box girder contains not only bending deflection but also two additional deformations respectively caused by shear lag and shearing action, this paper again revises the improved conjugated beam method (ICBM) based on the LFBG sensors to satisfy the requirements for monitoring two mentioned additional deformations. The best choice for the LFBG sensor placement in box gilder is also proposed in this paper due to strain fluctuation on flange caused by shear lag effect. Results from numerical simulations show that most of the theoretical monitoring errors of the revised ICBM are 0.3%~1.5%, and the maximum error is 2.4%. A loading experiment for a single-cell box gilder monitored by LFBG sensors show that most of the practical monitoring errors are 6%~8%, and the maximum error is 11%.

The uncertainty in the secondary path of an Active Noise Control (ANC) headphone affects the waterbed effect and stability of the feedback system. This study focuses on the uncertainty of the secondary path when real users wear headphones, and proposes a new uncertainty constraint based on the measured results of the secondary path transfer function under different wearing conditions of dummy head and limited subjects. This constraint and a cascaded second-order infinite impulse response filter with fixed coefficients are used to formulate a control strategic function, which is optimized by the Improved Grey Wolf Optimizer (IGWO) algorithm to obtain the optimal controller with better noise reduction performance. The proposed method and simulation model are validated based on the experimental test results. The results demonstrate that the safety factor and waterbed suppressing factor contained in the proposed uncertainty constraint ensures more stable noise reduction and effective suppression of the waterbed effect for new subjects without a priori data.

Methylenetetrahydrofolate reductase (MTHFR), an enzyme expressed in mammalian testes exerts direct effect on spermatogenesis; however, its protein characteristics in bovine testes remain unknown. Here, we analysed bovine testicular structure, MTHFR bioinformatics profile, mRNA, and protein expression characteristics in yellow-cattle (y-c) and yak testis using histological procedures, bioinformatics analysis, qRT-PCR, and western blot. Testes from 13 bovines, ≤ 2 years juvenile (y-c, n = 3; yak, n=3) and ≥ 3 years adult (y-c, n = 3; yak, n = 4) were collected and analysed. Anatomical characteristics of testis in y-c and yak were similar except the weight or size for which that of y-c was significantly higher or greater than yak. In y-c, an open reading frame (ORF) for 2600 nucleotides sequence, encoding 655 amino acids showed high homology with zebu cattle (99.51%) and wild yak (98.68%). Secondary and 3D protein structures were similar to that of humans with differences in number of nucleotides, amino acids, and some physico-chemical characteristics. MTHFR mRNA expression in y-c and yak were significantly higher in adult testes compared with juvenile ones. However, its protein expression was higher but not statistically significant in adult y-c and yak compared to the juvenile ones. The highlights and inferences of these and other findings are discussed.

Consumer IoT (CIoT) manufacturers seek customer feedback to enhance their products and services, creating a smart ecosystem like a smart home. Due to security and privacy concerns, Blockchain-based federated learning (BCFL) ecosystems can let CIoT manufacturers update their Machine Learning (ML) model using end-user data. FL uses privacy-preserving ML techniques to forecast customers' needs and consumption habits, and blockchain replaces the centralised aggregator to safeguard the ecosystem. However, Blockchain technology (BCT) struggles with scalability and quick ledger expansion. In BCFL, local model generation and secure aggregation are other issues. This research contributes a novel architecture emphasising Gateway Peer (GWP) in blockchain network to resolve scalability, ledger optimisation and secure model transmission issues. In the architecture we replace the centralised aggregator by the blockchain network, while GWP restricts the number of local transactions to execute in BCN. Considering the security and privacy of FL processes, we have added differential privacy and advanced normalisation techniques to ML processes. The approaches strengthen end-users' cyber security and encourage the adoption of technological innovation standards by service providers. The proposed approach has been tested extensively using a well-respected Stanford Cars dataset. We experimentally demonstrate that the proposed architecture makes the network scalable and optimises the ledger significantly. In addition, the normalisation technique outperforms batch normalisation when features are under DP protection.

Abstract: Transcription factors are crucial pre-transcriptional regulatory mechanisms that can modulate the expression of downstream genes by binding to their promoter regions. DOF (DNA binding with One Finger) proteins are a unique class of transcription factors with extensive roles in plant growth and development. Our previous research indicated a decrease in iron content in chlorotic bamboo leaves. However, to our knowledge, genes related to iron metabolism pathways in bamboo species have not yet been studied. Therefore, in the current study, we identified iron metabolism-related (IMR) genes in bamboo and determined the transcription factors that significantly influence them. Among these, DOFs were found to have widespread effects and potentially significant impacts on their expression. We identified specific DOF members in Dendrocalamus latiflorus with binding abilities through homology with Arabidopsis DOF proteins, and established connections between some of these members and IMR genes using RNA-seq data. Additionally, molecular docking confirmed the binding interactions between these DlDOFs and the DOF binding sites in the promoter regions of IMR genes. The co-expression relationship between the two gene sets was further validated using q-PCR experiments. This study paves the way for research into iron metabolism pathways in bamboo and lays the foundation for understanding the role of DOF transcription factors in D. latiflorus.

The meaning of a good social outcome in land use transport policy/planning has been relatively underdeveloped, compared to economic and environmental sustainability goals, but this is now changing. Cities are increasingly prioritizing reducing social exclusion, with the allied intent of providing all residents with equitable access to the benefits of their city. However, in jurisdictions that use cost-benefit analysis to guide government decision-making, this poses a challenge: monetization of the benefits of reducing social exclusion is poorly developed. An evaluation gap thus confronts benefit-cost based assessment of initiatives intended to reduce social exclusion, compared to initiatives directed towards societal economic and environmental goals. This is a particular problem for public transport services that primarily enable people at risk of mobility-related social exclusion to access more opportunities in their society (social transit). The benefits of reducing social exclusion associated with these services have not been monetized, so social transit initiatives are poorly placed to argue their merits against competing initiatives where benefit monetization is more advanced (e.g., mass public transport and roads). The paper summarizes Australian research that has developed monetized measures for the value of increased trip making, bridging/bonding social capital, sense of community and several conceptions of wellbeing, and of reducing neighbourhood disadvantage, as these contribute to reducing social exclusion. New Singaporean research on the value of trip making to support reduced exclusion is also presented, affirming the Australian trip values. Trip values are then used in case study examples to show they can make a material difference to the societal worth of initiatives intended to reduce exclusion. Using these trip values, and other pathway values linked to reducing social exclusion, closes or at least substantially reduces the evaluation gap confronting social goal achievement in land use transport policy and planning, strengthening the case for reducing exclusion. These values will assist jurisdictions that are seeking to provide their residents with more equitable access to the benefits of their city.

Quantitative differential phase contrast (qDPC) imaging has become an important method of optical measurement and life science research in microscopy because of its high reconstruction resolution and non-invasive, high-contrast and quantitative imaging of biological samples. Despite the continuous development of the principle and algorithm, the frame rate of the existing qDPC algorithm is still much lower than that of camera acquisition, so it is hardly applied to real-time image the fast-moving biological samples. In this paper, based on color-coded multiplexing strategy, a compact real-time quantitative phase imaging system is designed to realize multi-mode imaging. The system employs a programmable LED array to illuminate directly, and the phase reconstruction algorithm is deployed in the graphics processing unit (GPU) of the laptop to accelerate the calculation. The system can achieve high-speed quantitative phase imaging of non-stained biological samples, and the frame rate can reach 60fps. The device has the advantages of compact structure, low cost and portability. Thus, it is suitable for mobile medical applications.

With the development of artificial intelligence, the ability of capturing the background characteristics of hyperspectral imagery (HSI) is improved and promising performance in hyperspectral anomaly detection (HAD) tasks is yielded. However, existing methods proposed in recent years still suffer from certain limitations: 1) constraints are lacking in the deep feature learning process in terms of the issue for absence of prior background and anomaly information. 2) hyperspectral anomaly detectors with traditional self-supervised deep learning methods fail to ensure prioritized reconstruction of the background. 3) architectures of fully connected deep network in hyperspectral anomaly detectors lead to low utilization of spatial information and destruction for original spatial relationship of hyperspectral imagery, and disregard spectral correlation between adjacent pixels. 4) hypotheses or assumptions for background and anomaly distributions restrict the performance of many hyperspectral anomaly detectors because the distributions of background land covers are usually complex and not assumable in real-world hyperspectral imagery. With the consideration of above problems, in this paper, we propose a novel fully convolutional auto-encoder based on dual clustering and latent feature adversarial consistency (FCAE-DCAC) for HAD which is carried out in a self-supervised learning-based processing. Firstly, the density-based spatial clustering of applications with noise algorithm and connected component analysis are utilized for successive spectral and spatial clustering to obtain more precise prior background and anomaly information, which facilitates the separation between background and anomaly samples during the training of our method. Subsequently, a novel fully convolutional auto-encoder (FCAE) integrated with spatial-spectral joint attention (SSJA) is proposed to enhance the utilization of spatial information and augment feature expression. In addition, a latent feature adversarial consistency network is proposed to achieve pure background reconstruction with the ability of learning actual background distribution in hyperspectral imagery. Finally, a triplet loss is introduced to enhance the separability between background and anomaly, and the reconstruction residual serves as the anomaly detection result. We evaluate the proposed method on seven groups of real-world hyperspectral datasets, and the experimental results confirmed the effectiveness and superior performance of the proposed method versus nine state-of-the-art methods.

Existence of carcinogenic nitrite in food has attracted much attention, however, it is still a challenge to develop nitrite sensor with higher sensitivity and selectivity to enlarge its applications in daily life. Herein, one-dimensional honeycomb-like carbon nanofibers (HCNFs) were synthesized with an electrospun technology, and its specific structure enables the controlling growth and highly dispersed bismuth nanoparticles (Bi NPs) on its surface, which endows the obtained Bi/HCNFs with excellent electrocatalytic activity toward nitrite oxidation. By modifying Bi/HCNFs on screen-printed electrode, the constructed Bi/HCNFs electrode (Bi/HCNFs-SPE) can be used for nitrite detection in one drop of solution, and exhibits higher sensitivity (1269.9 μA mM-1 cm-2) in a wide range of 0.1~800 μM with lower detection limit (19 nM). Impressively, the Bi/HCNFs-SPE has been successfully used for nitrite detection in food and environment samples, the satisfactory property and recovery indicates its feasibility in further practical applications.

The Shimensi super-large tungsten polymetallic deposit is located in Late Jurassic- Early Cretaceous Porphyry-Skarn tungsten ore belt in the south Yangtze metallogenic belt. There are 3 types of mineralization: veinlet-disseminated type, thick quartze vein type and hydrothermal crypto-explosive breccia type. Based on geological studies, this paper presents new petrographic, microthermometric, laser Raman spectroscopic and hydrogen and oxygen isotope research of the fluid inclusions from the deposit. The results show that there are five different types of fluid inclusions: liquid-rich inclusions, vapor-rich inclusions, pure liquid inclusions, pure vapor inclusions, and fluid inclusions containing a solid crystal. The homogenization temperatures of the fluid inclusion range from 140℃-270℃, the salinities are 3%-5% NaCleq and the densities of ore-forming fluid range from 0.64 g/cm3 to 0.99 g/cm3. For the analyses of Laser Raman spectroscopic, the ore-forming fluids can be approximated by a Ca2+-Na+-SO42--Cl- fluid system with small amount of CO2, CH4 and N2. Otherwise, the datas of the pressure, pH and Eh show a fluid metallogenic environment of low pressure, weak acid and weak reduction. The values of the homogenization temperature in 3 types of orebodies suggest that the mineralization is characterized by the decrease of the temperature under the condition of the fluid immiscibility. The H-O isotope values are interpreted to indicate that the ore-forming fluids are mainly composed of magmatic water, and also the meteoric water was added with the process of the magma rising.

Buckling defect will appear on the outer surface of the deformed ring during constrained ring rolling (CRR) of aluminum alloy thin wall conical ring with inner high ribs (AATWCRIHR), if the geometrical dimension of the ribs doesn't match the wall thickness. To avoid the buckling defect, a quantitative method for characterizing the degree of the buckling defect is proposed using the area of buckling profile. Then an orthogonal experimental scheme was designed taking the width of the middle rib, thickness of wall, and height of the middle rib as design variables and defining the area of buckling profile as optimization objective. Subsequently, a quadratic polynomial response surface model was established by combining the optimization algorithm with the finite element method (FEM), and the geometrical dimension of the middle ribs of the deformed AATWCRIHR is optimized. Also the optimal parameter combination to minimize the area of buckling profile is obtained and verified using FE simulation. Results show that the AATWCRIHR after optimization doesn’t generate the buckling defect during constrained ring rolling, and it is proved that the quantitative buckling defect representation method and the optimization design method based on the response surface model and the finite element simulation results are feasible for the constrained ring rolling process of the AATWCRIHR.

Numerous studies have demonstrated that multiple intrinsic and extrinsic factors shape the structure and composition of gut microbiota in a host. The disorder of gut microbiota may trigger various host diseases. Here, we collected fecal samples from wild-caught Japanese geckos (Gekko japonicus) and captive conspecifics fed with mealworms (mealworm-fed geckos) and fruit flies (fly-fed geckos), aiming to examine dietary and sexual correlates of gut microbiota. We used the 16S rRNA gene sequencing technology to determine the composition of gut microbiota. The dominant phyla with a mean relative abundance higher than 10% were Verrucomicrobiota, Bacteroidota and Firmicutes. Gut microbial community richness was higher in mealworm-fed geckos than in fly-fed and wild geckos, and community diversity was higher in mealworm-fed geckos than in wild geckos. Neither alpha nor beta diversity of gut microbiota differed among wild, mealworm-fed and fly-fed geckos. The beta rather than alpha diversity of gut microbiota was sex-dependent. Based on the relative abundance of gut bacteria and its gene functions, we concluded that gut microbiota contributed more significantly to the host’s metabolic and immune functions. Higher diversity of gut microbiota in mealworm-fed geckos could result from higher chitin contents of insects of the order Coleoptera. This study not only provides basic information about the gut microbiota of G. japonicus, but also shows that gut microbiota correlates with dietary habit and sex in the species.

Lymphoma diagnoses in the U.S. are substantial, with an estimated 89,380 new cases in 2023, necessitating innovative treatment approaches. Phase 1 clinical trials play a pivotal role in this context. We developed a binary predictive model to assess trial adherence to expected average durations, analyzing 1,089 completed Phase 1 lymphoma trials from clinicaltrials.gov. Using machine learning, the Random Forest model demonstrated high efficacy with an accuracy of 0.7248 and ROC-AUC of 0.7701 for lymphoma trials. Importantly, this model maintained an accuracy of 0.7405 when applied to lung cancer trials, showcasing its versatility. A key insight is the correlation between higher predicted probabilities and extended trial durations, offering nuanced insights beyond binary predictions. Our research contributes to enhanced clinical research planning and potential improvements in patient outcomes in oncology.

This paper proposes to combat active eavesdropping by intelligent reflecting surface (IRS) backscatter techniques. To be specific, the source (Alice) sends the confidential information to the intended user (Bob), while the eavesdropper (Willie) transmits jamming signal to interrupt the transmission for more data interception. To enhance the secrecy, an IRS is deployed and connected with Alice through fiber to transform the jamming signal into the confidential signal by employing backscatter techniques. Based on the considered model, an optimization problem is formulated to maximize signal-to-interference-plus-noise ratio (SINR) at Bob under the constraints of the transmit power at Alice, the reflection vector at the IRS and the allowable maximum SINR at Willie. To address the optimization problem, an alternate optimization algorithm is developed. The simulation results verify the achievable secrecy gain of the proposed scheme.

Owing to the advantages of cost-effectiveness, compactness, and the avoidance of complicated camera synchronization, single-camera three-dimensional (3D) digital image correlation (DIC) techniques have gained increasing attention for deformation measurement of materials and structures. In the traditional single-camera 3D-DIC system, the left and right view images can be recorded by a single camera using a diffraction grating, a bi-prism or a set of planar mirrors. To further improve the measurement accuracy of single-camera 3D-DIC, this paper introduces a single-camera four-view imaging technique by installing a pyramidal prism in front of the camera. The 3D reconstruction of the measured points before and after deformation is realized with eight governing equations induced by four views, and the strong geometric constraints of four views can help to improve the measurement accuracy. A static experiment, a rigid body translation experiment and a four-point bending experiment show that the proposed single-camera 3D-DIC method can achieve higher measurement accuracy than the dual-view single-camera 3D-DIC techniques and has advantages in reducing both random error and systematic error.

To investigate the effects of organic fertilizer combined with reduced chemical fertilizer on radish yield, quality, and soil environment in high mountainous areas (elevation: 1800 m), and to mitigate the environmental pollution caused by excessive use of chemical fertilizers. The field trial was conducted to study the effects of different fertilizer treatments. (Control:local fertilizer application rate: 375 kg·hm² reduction in chemical fertilizer + 4500 kg·hm² organic fertilizer; T1:12% reduction in chemical fertilizer + 4500 kg·hm² organic fertilizer; T2:20% reduction in chemical fertilizer + 4500 kg·hm² of organic fertilizer; T3:28% reduction in chemical fertilizer + 4500 kg·hm² organic fertilizer). Four different fertilizer ratios were studied to assess their impacts on radish quality, yield, and soil environment. The findings showed that T2 significantly increased radish yield by 12.92%. Moreover, it led to significant improvements in the content of vitamin C, soluble sugars, soluble solids, soluble proteins, titratable acidity, and glucosinolates, which increased by 10.62%, 2.15%, 50.00%, 26.90%, 43.90%, and 44.57%, respectively. Treatment T2 also significantly increased soil nutrient content, with a 7.69% and 14.29% increase in total nitrogen and total phosphorus content compared to the control (Control) treatment, and a significant reduction of 21.64% in soil bulk density . T2 treatment significantly enhanced soil urease activity, sucrase activity, alkaline phosphatase activity, and catalase activity, showing an improvement of 28.97%, 55.92%, 52.08%, and 17.47% compared to the control, respectively (p&lt;0.05). Moreover, treatment T2 resulted in a relative abundance increase of 12.25% and 10.43% in Proteobacteria and Actinobacteria respectively. Thus, the combined application of T2:20% reduction in chemical fertilizer + 4500 kg·hm² of organic fertilizer improved the quality and yield of radish while optimizing the soil environment. T2 effectively promoted radish growth, enhanced radish yield and quality, and improved the soil environment.

In wireless sensor networks (WSNs), each sensor node can estimate the global parameter from the local data in distributed manner. This paper proposed a robust diffusion estimation algorithm based on minimum error entropy criterion with self-adjusting step-size, which are referred to as diffusion MEE-SAS (DMEE-SAS) algorithm. The DMEE-SAS algorithm has fast speed of convergence and is robust against non-Gaussian noise in the measurements. The detailed performance analysis of the DMEE-SAS algorithm is performed. By combining the DMEE-SAS with diffusion minimum error entropy (DMEE) algorithms, an Improving DMEE-SAS algorithm is proposed, in non-stationary environment where tracking is very important. The Improving DMEE-SAS algorithm can avoid insensitivity of the DMEE-SAS algorithm due to the small effective step-size near the optimal estimator, and obtain a fast convergence speed. Numerical simulations are given to verify the effectiveness and advantages of these proposed algorithms.

In this paper, an adaptive technology and the interconnection and damping assignment passivity-based control method are combined to solve the stabilization problem for underactuated mechanical systems with uncertainties (including matched and unmatched). Uncertainties include unknown friction coefficients and unknown terms in kinetic energy and potential energy. A novel adaptive interconnection and damping assignment passivity-based control scheme is proposed and an adaptive stabilization controller is designed to make the closed-loop system locally stable. Verification is conducted on the ball and beam system, taking into account uncertainties of friction coefficients, kinetic energy, and potential energy. The locally asymptotic stability is demonstrated using the LaSalle’s invariance principle and approximate linearization. The effectiveness of the proposed control law is verified through numerical simulations.

As a member of smart materials, electrorheological elastomers (EREs) formed by pre-treating active electrorheological particles are attracting more and more attention. In this work, four Mg-doped strontium titanate particles with spherical, dendritic, flake-like and pinecone-like morphorlogies were obtained by hydrothermal and low-temperature co-precipitation. XRD, SEM, Raman and FT-IR were used to characterize the obtained products. The results showed that the sizes of Mg-doped strontium titanates are about 1.5‒2.0 μm, and the phase structure are dominated by cubic crystal. These Mg-doped strontium titanates were dispersed in a hydrogel composite elastic medium. Then, Mg-doped strontium titanate/glycerol/gelatin electrorheological composite hydrophilic elastomers were obtained with or without electric field. The electric field response properties of Mg-doped strontium titanate composite elastomers were investigated. It concluded that dendritic Mg-doped strontium titanate composite elastomers is high-performance EREs. And the maximum value of energy storage modulus of Mg-doped strontium titanate composite elastomers has achieved 8.70 MPa. This high electrorheological performance of the products is helpful for their applications in vibration control, force transducers, smart structures, dampers, and other fields.

This study aimed to investigate the fatigue performance and interfacial strengthening mechanisms of Al6061-to-Cu dissimilar lap joints via electromagnetic pulse welding (EMPW). The load-bearing capacity of the joints at discharge voltages of 14 kV and 16 kV was superior to that of 12 kV. Furthermore, the fatigue life of the 14 kV joints was one order of magnitude higher compared to the 12 kV joints. SEM observation of the fatigue fracture surface revealed the presence of typical "tire-mark" fatigue striations only in the 14 kV joint, indicating higher ductility and the ability to withstand extended plastic deformation. Notably, ultra-fine nanocrystalline Al2Cu phase, amorphous phase, and numerous dislocations hindered EBSD acquisition in the transition zone. Nevertheless, dense low-angle grain boundaries (LAGBs) and refined grains were examined at the bonding interface. This suggests that the high-velocity collision caused severe plastic deformation and led to the formation of substructures. The interfacial strength was attributed not only to the "wave-like" or "inverted hook-like" diffusion layer but also to the presence of refined grains along the interface and nanocrystalline Al2Cu in the transition zone. Furthermore, the hybrid nanocrystalline-amorphous microstructure strengthened the joint by regulating the balance between strength and ductility.

Promoting green development has become an important way to optimize the ecological and economic structure and promote sustainable development. The Yangtze River Economic Belt is an important economic corridor in China, and it remains to be examined whether the implementation of environmental regulations has enhanced the green total factor productivity (GTFP) of cities. This paper calculates the green total factor productivity of 107 cities within the Yangtze River Economic Belt by using the super-efficient SBM model and the GML index with Chinese city panel data from 2007-2019 and measures the intensity of environmental regulations through textual analysis. The bidirectional fixed-effects model constructed in this paper suggests an inverted U-shaped relationship between environmental regulation and GTFP, which is confirmed by a series of robustness tests. Green technology innovation and advanced industrial structure play a mechanism role in this. In regions with lower levels of green technology and industrial structure, the inverted U-shaped relationship between environmental regulation and green total factor productivity is more significant. In addition, the phenomenon of GTFP rising and then falling because of environmental regulation is more obvious in cities in the middle and upper reaches of the Yangtze River and outside the urban agglomerations. Therefore, when formulating environmental regulation policies, it is necessary to balance the relationship between economic development and environmental protection and harmonize the environment and economic development of the entire Yangtze River Basin.

In this paper, the synthesis of two novel luminescent Eu3+ ion complexes [Eu(TFT)3(phen) (1) and Eu(TFT)3(bpy)•Hex (2)] based on the combination of 2-(2,2,2-trifluoroethyl)-1-tetralone (TFT), containing n-donor ligands (1,10-phenanthroline or 2,2'-Bipyridine) and Eu3+ ion is reported herein, and their structural features are discussed on the basis of X-ray crystallographic and thermal analyses. We observed that the ligands transfer energy effectively to the metal center by fluorescence, IR and UV spectrograms studies. The structures and properties of complexes 1-2 were optimized by the DFT theoretical calculation, and the calculation results were consistent with the experimental X-ray structure data and spectral analysis.

This study has simulated the typical rainstorm on 20 July 2021 over central east China by using the first-generation Chinese Reanalysis datasets and Global Land Data Assimilation System datasets, and the Noah land surface model coupled with the advanced weather research and forecasting model. Based on this, the gridded planetary boundary layer (PBL) profiles and ensemble states within soil perturbations are collected to investigate the main land-atmosphere coupling characteristics during this modeled rainstorm by using various local coupling metrics and the introduced ensemble statistical metrics. Results have shown that (1) except for the stratospheric thermodynamics and surface thermal over mountain areas, the main characteristics of mid-low layers and surface have been well documented in this modeled rainstorm; (2) the typical coupling intensity is characterized by the dominant morning moistening, early noon weak PBL warming around 2, noontime buoyant mixing temperature deficit around 274 K, daytime PBL and surface latent flux contribution around 100 and 280 W/m2 respectively, and significant afternoon soil-surface latent flux coupling; (3) moist static energy is more significant than PBL height during the relation chains, which is consistent with the significance of surface moistening indicated by local coupling metrics. In general, wet soil contributes greatly to daytime moisture evaporation, which then increases the early noon PBL warming and enhances the noontime buoyant mixing within weak flux contribution. However, this has been suppressed by large-scale forcing such as the upper southwestern inflows of rainstorms, which has further significantly shaped the spatial distribution of statistical metrics in contrast. These quantitatively described local couplings have highlighted both the convection potential diagnoses usage for the local weather application and more applicable coupling threshold diagnoses within the finer spatial investigation.

A novel prediction model for crack development of reinforced concrete (RC) piles with localized chloride corrosion in marine environment is proposed. A discrete method is used to solve the corrosion pit radius model and a crack extension model is developed to investigate the initiation and extension of cracks. The maximum corrosion degree of reinforced concrete pile is predicted according to the limit crack criterion, and finally a sensitivity analysis is carried out on the important parameters of crack extension. The results show that the radius of corrosion pit, the depth corrosion pit and cross-sectional area loss of reinforcement gradually increase as the corrosion level increases. The loss of local reinforcement section at crack initiation decreases with the increase of the ratio of concrete cover to initial diameter, and increases with the increase of pitting factor. The required pit depth for reinforcement cracking increases with the increase of the ratio of concrete cover thickness to diameter. The loss of cross-sectional area of reinforcement and the radius of corrosion pit increase with the increase of initial diameter of reinforcement. Increasing the pitting factor will reduce the pit depth and make the crack width develop faster before reaching the limit crack width. Increasing the concrete cover thickness can provide an improvement in the propagation of cracks. A comparative analysis shows that the localized corrosion pattern is more in conformity with marine engineering practice.