JIS SUJ2 is most widely used in bearing steels. The advantages are good hardenability, excellent fatigue, wear resistance and comprehensive mechanical properties. For wear resistance and fatigue resistance of the steel are getting more and more attention, the residual stress state and its distribution on the surface of the heat affect zone are critical factors affecting the fatigue life and wear resistance of the parts. In this study, using the SUJ2 as the material to talk about the surface residual stress and retained austenite distribution. Doing the quenching and tempering treatment to obtain different microstructures, using the induction method to re-quench the case region. After the heat treatment, measuring the residual stress and retained austenite volume on the surface by X-ray diffraction, observing the microstructure and comparing the hardness. The results show that the microstructure after heat treatment contains unsolidified carbides, tempered martensite and retained austenite. The residual stress on the surface is the tensile state. In the re-hardened area after induction quenching, the residual stress is all compressive, and the values are more than -800 MPa. In conclusion, in the same output power condition can be observed that the microstructure of the specimens before induction hardening has a significant impact on the effective case depth. The surface residual stress has changed from a tensile to a compressive state. In the re-hardened area, the maximum of the residual compressive stress increased with the austenitized temperature increase.

Cannabidiol (CBD) is an active diterpenoid compound that is extracted from the leaves and stem of Cannabis sativa. Previous studies show that CBD is a non-psychotropic compound with significant anti-cancer effects. This study determines its cytotoxic effect on oral cancer cells and OECM1 cells and compares the outcomes with a chemotherapeutic drug, cisplatin. This study determines the effect of CBD on the viability, apoptosis, morphology and migration of OECM1 cells. Electric cell-substrate impedance sensing (ECIS) is used to measure the change in cell impedance for cells that are treated with a series concentration of CBD for 24 hours. AlamarBlue and annexin V/7-AAD staining assays show that CBD has a cytotoxic effect on cell viability and induces cell apoptosis. ECIS analysis shows that CBD decreases the overall resistance and morphological parameters at 4 kHz in a concentration-dependent manner. There is a significant reduction in the wound-healing recovery rate for cells that are treated with 30 μM CBD. This study demonstrates that ECIS can be used for in vitro screening of anticancer drugs and is more sensitive, functional and comprehensive than traditional biochemical assays. CBD also increases cytotoxicity on cell survival and the migration of oral cancer cells, so it may be a therapeutic drug for oral cancer

Background: Tumor microenvironment (TME) plays a crucial role in virtually every aspect of tumorigenesis of glioblastoma multiforme (GBM). The dysfunctional TME promotes drug resistance, disease recurrence and distant metastasis. Recent evidence indicates that exosomes released by stromal cells within TME may promote oncogenic phenotypes via transferring signaling molecules such as cytokines, proteins and microRNAs. Results: In this study, clinical GBM samples were collected and analyzed. We found that GBM-associated macrophages (GAMs) secreted exosomes which were enriched with oncomiR-21. Co-culture of GAMs (and GAM derived exosomes) and GBM cell lines resulted in the increased GBM cells’ resistance against temozolomide (TMZ) by upregulating pro-survival gene, PDCD4 and stemness markers Sox2, STAT3, Nestin and miR-21-5p and increased M2 cytokines, IL-6 and TGF-β1 secreted by GBM cells, promoting the M2 polarization of GAMs. Subsequently, pacritinib treatment suppressed GBM tumorigenesis and stemness; more importantly, pacritinib-treated GBM cells showed markedly reduced ability to secret M2 cytokines and reduced miR-21 enriched exosomes secreted by GAMs. Pacritinib-mediated effects were accompanied by a reduction of oncomiR miR-21-5p, by which tumor suppressor PDCD4 was targeted. We subsequently established a patient-derived xenograft models where mice bore patient GBM and GAMs. The treatment of pacritinib, and the combination of pacritinib/TMZ appeared to significantly reduce tumorigenesis of GBM/GAM PDX mice, overcome TMZ-resistance, and M2 polarization of GAMs. Conclusion: In summation, we showed that potential of pacritinib alone or in combination with TMZ for suppressing GBM tumorigenesis via modulating STAT3/miR-21/PDCD4 signaling. Further investigations are warranted for adopting pacritinib for the treatment of TMZ-resistant GBM in the clinical settings.

A three-dimensional, unstructured grid, hydrodynamic and suspended-sediment transport model (i.e., SELFE-SED) was developed to simulate temporal and spatial variations of suspended sediment and was applied to the subtropical subalpine Tsuei-Feng Lake (TFL) of Taiwan. The model was validated with measured water level and suspended‑sediment concentration in 2009, 2010, and 2011. The overall model simulation results are in quantitative agreement with the observational data. The validated model was then applied to explore the most important parameter that affects the suspended-sediment concentration and to investigate the effect of wind stress on the mean current and suspended‑sediment distribution in this shallow lake. Modeling results of sensitivity analysis reveal that the settling velocity is a crucial parameter and erosion rate is less important in the suspended-sediment transport model. Remarkable lake circulation was found based on the strength of wind speed and wind direction. Strong wind would result in higher mean current in the top layer and suspended-sediment distribution in the top and bottom layers. This study demonstrated that the wind stress played a significant influence on mean circulation and suspended-sediment transport in a shallow lake.

The International Roughness Index (IRI) is the standard scale for evaluating road roughness in many countries in the world. The Taipei City government actively promotes a Road Smoothing Project and plans to complete the rehabilitation of the main and minor roads within its jurisdiction. This study aims to detect the road surface roughness in Taipei City and recommend appropriate IRI thresholds for road rehabilitation. A total of 171 asphalt concrete pavement sections in Taipei City with a total length of 803.49 km were analyzed and compared by IRI. The longitudinal profile of the detected road sections was measured using an inertial profiler. The statistical analysis showed that the IRI value prior to road leveling was mainly distributed between 5 and 8 m/km, while the IRI value after road leveling was mainly distributed between 3 and 4.5 m/km. This confirms that the implementation of the Road Smoothing Project has a significant effect on improving road smoothness. Moreover, based on the analysis results, it is recommended that the IRI threshold value for road rehabilitation in Taipei City be set at 4.50 m/km.

Continuous research into the availability of phosphorus (P) in forest soil is critical for sustainable management of forest ecosystems. In this study, we used sequential chemical extraction and 31P-nuclear magnetic resonance spectroscopy (31P-NMR) to evaluate the form and distribution of inorganic P (Pi) and organic P (Po) in Casuarina forest soils of a subtropical coastal sand dune at Houlong in Taiwan. The soil samples were collected from humic (+2-0 cm) and mineral layers (mineral-I: 0-10, mineral-II: 10-20 cm) at two topographic locations (upland and lowland) by elevation. Sequential chemical extraction revealed that the NaOH-Po fraction, as moderately recalcitrant P, was the dominant form in humic and mineral-I layers in both upland and lowland soils, whereas the cHCl-Pi fraction was the dominant form in the mineral-II layer. Resistant P content, including NaOH-Pi, HCl-Pi, cHCl-Pi, and cHCl-Po fractions, was higher in the upland than lowland in the corresponding layers; however, labile P content, NaHCO3-Po, showed the opposite pattern. Content of resistant Pi (NaOH-Pi, HCl-Pi, and cHCl-Pi) increased significantly with depth, but that of labile Pi (resin-Pi and NaHCO3-Pi) and recalcitrant Po (NaHCO3-Po, NaOH-Po, and cHCl-Po) decreased significantly with depth at both locations. 31P-NMR spectroscopy revealed inorganic orthophosphate and monoesters-P as the major forms in this area. The proportions of Pi and Po evaluated by sequential chemical extraction and 31P-NMR spectroscopy were basically consistent. The results indicated that the soils were in weathered conditions. Furthermore, the P distribution and forms significantly differed between the upland and lowland by variation in elevation and eolian aggradation effects in this coastal sand dune landscape.

The rapid development of multicopters has led to many security problems. In order to prevent multicopters from invading restricted areas or famous buildings, an Anti-UAV Defense System (AUDS) has been developed and become a research topic of interest. Topics under research in relation to this include electromagnetic interference guns for unmanned aerial vehicles (UAVs), high-energy laser guns, US military net warheads, and AUDSs with net guns. However, these AUDSs use either manual aiming or expensive radar to track UAVs. This paper proposes a dual-axis rotary platform with UAV automatic tracking. The tracking platform uses visual image processing technology to track and lock the dynamic displacement of a UAV. When a target UAV is locked, the system uses a nine-axis attitude meter and laser rangefinders to measure its flight altitude and calculates its longitude and latitude coordinates through sphere coordinates to provide UAV monitoring for further defense or attack missions. Tracking tests of UAV flights in the air were carried out using a DJI MAVIC UAV at a height of 30 meters to 100 meters. It was set up for UAV image capture and visual recognition for tracking under various weather conditions by a thermal imager and a full-color camera respectively. When there was no cloud during the daytime, the images captured by the thermal imager and full-color camera provide a high-quality image recognition result. However, under dark weather, black clouds will emit radiant energy and seriously affect the capture of images by a thermal imager. When there is no cloud at night, the thermal imager performs well in UAV image capture. When the UAV is tracked and locked, the system can effectively obtain the flight altitude and longitude and latitude coordinate values.

Adipose-derived stem cells (ADSCs) were suggested for treating degenerative osteoarthritis, suppressing inflammatory responses, and repairing damaged soft tissues. Moreover, the ADSCs have the potential to undergo self-renewal and differentiate into bone, tendon, cartilage, and ligament. Recently, investigation of the self-renewal and differentiation of the ADSCs becomes an attractive area. In this work, a pneumatic microdevice has been developed to study the gene expression of the ADSCs after the stimulation of multi-axial tensile strain. The ADSCs were cultured on the microdevice and experienced multi-axial tensile strain during a 3-day culture course. Self-renewal and differentiation abilities were investigated by mRNA expressions of NANOG, SOX2, OCT4, SOX9, PPAR-γ, and RUNX2. The result showed that the genes related self-renewal were significantly up-regulated after the tensile stimulation. Higher proliferation ratio of the ADSCs was also shown by cell viability assay. The microdevice provides a promising platform for cell-based study under mechanical tensile stimulation.

Emerging evidence demonstrated that using a new manufacturing technology to produce γ-aminobutyric acid (GABA)-fortified oolong (GO) tea could relieve human stress and exert versatile physiological benefits. The purpose of this human research aims to investigate therapeutic effects of daily GO tea consumption on the improvement of blood pressure, relaxation-related brain waves and quality of life (QOL) during a period of 28 consecutive days. Total polyphenols, major catechins and free amino acids were analyzed via HPLC assay. Changes of heart rate, blood pressure, α-brain wave (index of relaxation) and eight-item QOL score were investigated on day 0, 7, 14, 21 and 28, respectively. The chemical analysis results showed that GO tea contained the most abundant amino acids and GABA, contributing to the relaxation activity. Among all study participants, daily drinking GO tea could reduce systolic blood pressure on day 21 and diastolic blood pressure on day 28 (p < 0.05, respectively). For participants with pre-hypertension, GO tea could effectively reduce heart rate, systolic and diastolic blood pressure on day 28 (p < 0.05). At the end of the study, incremental changes in alpha-brain wave and QOL scores were also demonstrated (p < 0.05, respectively). This study recommended that GO tea might potentially serve as a natural source of alternative therapy to benefit blood pressure, stress-relief and QOL.

To quantify damage to reinforced concrete (RC) column members after an earthquake, an engineer needs to know the maximum applied force that was generated by the earthquake. Therefore, in this work, piezoceramic transducers are used to detect the applied force on an RC column member under dynamic loading. To investigate the use of post-embedded piezoceramic sensors in detecting the force that is applied to RC columns, eight full-size RC column specimens with various failure modes are tested under specific earthquake loadings. Post-embedded piezoceramic sensors are installed at a range of depths (70-80 mm) beneath the surface of a column specimen to examine the relationship between the signals that are obtained from them and the force applied by the dynamic actuator. The signals that are generated by the post-embedded piezoceramic sensors, which correlate with the applied force, are presented. These results indicate that the post-embedded piezoceramic sensors have great potential as tools for measuring the maximum applied force on an RC column in an earthquake. Restated, signals that are obtained from post-embedded piezoceramic sensors on an RC column in an earthquake can be used to determine the applied force and corresponding damage or residual seismic capacity.

Background: Most drug-resistant Escherichia coli isolates in dogs come from diseased dogs. Prior to this study, the prevalence and risk factors of fecal carriage drug-resistant E. coli and epidemic clone sequence type (ST) 131 (including subtypes) isolates in dogs were unknown. Methods: Rectal swabs were used for E. coli isolation from 299 dogs in a veterinary teaching hospital in Taiwan. Antibiotic resistance and multiplex PCR analyses of E. coli for major STs were performed. Result: There were 43.1% cefazolin-resistant, 22.1% fluoroquinolone-resistant, and 9.4% extended-spectrum beta-lactamase-producing E. coli in our cohort. In the phylogenetic study, B2 was the predominant group (30.1%). The cefazolin-resistant group and ciprofloxacin-resistant group had greater antibiotic exposure in the last 14 days (P < 0.05). The age, sex, and dietary habits of the antibiotic-resistant and -susceptible groups were similar. In the seven isolates of ST131 in fecal colonization, the most predominant subtypes were FimH41 and FimH22. Conclusion: Recent antibiotic exposure was related to the fecal carriage of antibiotic-resistant E. coli isolates. Three major subtypes (FimH41, H22, and H30) of ST131 can thus be found in fecal carriage in dogs in Taiwan.

A new-type vibration sensor based on a fiber Bragg grating combining with a special structure-packaged design is proposed for monitoring the mechanical vibration signals. Three different sensing structures including the film squeeze type, new film squeeze type and elastic tape squeeze type are proposed for measuring the vibration signals with the frequency range from tens to thousands of Hz. In the comparison of experimental results, the new film squeeze structure has a nice sensing performance in the range from 100 to 1000 Hz with the sensitivity of 35 mV/V. For the elastic tape squeeze structure, the elastic tape is designed to encapsulate the optical fiber with a good frequency response from 1100 to 3100 Hz. In addition, by using the new film squeeze structure to measure the steady-state and non-steady-state vibration signals, the spectral components of sensing signals are analyzed by using the wavelet transformation for confirming the testing signals. These vibration fiber sensors can be applied in the measurement of high-end manufacture-facility vibration or earthquake vibrations etc.

Background and Aims: The impact of antibody response after direct-acting antiviral (DAA) therapy in hepatitis C virus (HCV)-infected recipients before and after liver transplantation (LT) is still undetermined. Methods: In this observational cohort study, we aimed to explore the association of changes in anti-HCV antibody titers after pre-LT DAA therapy with allograft injury, including biliary complications (BCs) and acute cellular rejection (ACR). Results: A total of 153 cases were enrolled from January 2015 to February 2021. Serum anti-HCV antibody titers were assessed before and after (day 30) LT. Among all recipients, 31/153 (20.3%) had pre-LT DAA therapy (DAA group) and 122/153 (79.7%) did not undergo pre-LT DAA therapy (DAA-naïve group). Higher incidence of post-LT BCs was observed in the DAA group (P = 0.028). Compared with the DAA-naïve group, the DAA group had a significantly higher mean level of anti-HCV titer upregulation (P = 0.0024); furthermore, among the recipients with BCs (n = 28) and ACR (n = 41), those in the DAA group exhibited significantly higher mean levels of anti-HCV antibody titer upregulation (P < 0.005). Conclusion: In conclusion, we speculated that anti-HCV antibody titer upregulation, which might have been induced by restoration of HCV-specific immune responses with pre-LT DAA therapy, were associated with post-LT allograft injury.

Background/Objectives: The study aimed to assess the reactogenicity and immunogenicity of various SARS-CoV-2 vaccines and compare their protective effects against COVID-19 among healthcare workers (HCWs) during the Omicron outbreak in Taiwan.Methods: Conducted from March 2021 to July 2023, this prospective observational study included healthy HCWs without prior COVID-19 immunization. Participants chose between adenovirus-vectored (AstraZeneca), mRNA (Moderna, BioNTech-Pfizer), and protein-based (Medigen, Novavax) vaccines. Blood samples were taken at multiple points to measure neutralizing antibody (nAb) titers, and adverse events (AEs) were recorded via questionnaires. Results: Of 710 HCWs, 668 (94.1%) completed three doses, and 290 (40.8%) received a fourth dose during the Omicron outbreak. AEs were more common with AstraZeneca and Moderna vaccines, while Medigen caused fewer AEs. Initial nAb titers were highest with Moderna but waned over time regardless of the vaccine. Booster doses significantly increased nAb titers, with the highest levels observed in Moderna BA1 recipients. The fourth dose significantly reduced COVID-19 incidence, with Moderna BA1 being the most effective.Conclusions: Regular booster doses, especially with mRNA and adjuvant-protein vaccines, effectively enhance nAb levels and reduce infection rates, providing critical protection for frontline HCWs during variant outbreaks.

The productivity of forests is often considered to be limited by the availability of phosphorus (P). Knowledge of the role of organic and inorganic P in humid subtropical forest soils is lacking. In this study, we used chemical fractionation and 31P nuclear magnetic resonance (NMR) spectroscopy to characterize the form of P and its distribution in undisturbed perhumid Chamaecyparis forest soils. The toposequence of transects was investigated for the humic layer from summit to footslope and lakeshore. The clay layer combined with a placic-like horizon in the subsoil may affect the distribution of soil P because both total P and organic P (Po) contents in all studied soils decreased with soil depth. In addition, Po content was negatively correlated with soil crystalline Fe oxide content, whereas inorganic P (Pi) content was positively correlated with soil crystalline Fe oxide content and slightly increased with soil depth. Thus, Pi may be mostly adsorbed by soil crystalline Fe oxides in the soils. Among all extractable P fractions, the NaOH-Po fraction appeared to be the major component, followed by NaHCO3-Po; the resin-P and HCl-Pi fractions were lowest. In addition, we found no typical trend for Pi and Po contents in soils with topographical change among the three sites. From the 31P-NMR spectra, the dominant Po form in soils from all study sites was monoesters with similar spectra. The 31P-NMR findings were basically consistent with those from chemical extraction. Soil formation processes may be the critical factor affecting the distribution of soil P. High precipitation and year-round high humidity may be important in the differentiation of the P species in this landscape.

Background: Post-marketing surveillance is crucial for gathering data on vaccine reactogenicity, enhancing public trust in immunization, and promoting vaccine uptake. This study aims to characterize adverse events following immunization (AEFI) and estimate the incidence rates of adverse reactions (ARs) associated with vaccines included in Taiwan's Expanded Program on Immunization (EPI). The study utilizes data from Taiwan's Vaccine Injury Compensation Program (VICP). Methods: Vaccine injury claims submitted to the VICP between 2014 and 2019 were analyzed. ARs were defined as AEFIs adjudicated as ‘related’ or ‘indeterminate’ by the VICP committee. Data on the annual number of vaccine doses administered was obtained from the Taiwan CDC, which helped calculate AR incidence rates. Results: A total of 491 AEFI claims were reviewed, with 327 (66.6%) categorized as ARs. AEFIs were mainly associated with the Bacillus Calmette-Guérin (BCG) vaccine (43.4%) and the seasonal influenza vaccine (22.0%). Most EPI vaccines demonstrated low AR incidence rates, ranging from 1.68 to 13.6 per million doses, with the exception of BCG, which exhibited 162.5 ARs per million doses. Shifting BCG immunization from below 5 months to at least 5 months reduced osteomyelitis incidence significantly, from 41.4 to 7.9 (P = 0.0014), but increased abscess and lymphadenitis cases. Conclusion: EPI vaccines in Taiwan are highly safe, with minimal AR incidences in the general population. The BCG vaccine remains an exception, occasionally causing severe ARs like osteomyelitis. Adjusting the immunization schedule to an older age may mitigate some of these adverse effects.

Species richness is a widely used measure for assessing the diversity of a particular area. However, observed richness often underestimates the true richness due to resource limitations, particularly in the small-sized sample or highly heterogeneous assemblage. Estimating species richness in a large-scale region typically involves an integrated data set consisting of subsamples collected independently from different subregions. However, the pooled sample of integrated data is no longer a random sample from the entire region, and the use of different sampling schemes results in variations in data formats. Consequently, employing a single sampling distribution to model the pooled sample becomes impractical, rendering existing richness estimators inadequate. This study theoretically explains the applicability of Chao's lower bound estimators in estimating species richness for large-scale areas using the pooled sample. Additionally, a new nonparametric estimator is introduced, which adjusts the bias of Chao's lower bound estimator by leveraging the Good-Turing frequency formula. This proposed estimator only utilizes the pooled sample's singleton, doubleton, and tripleton richness. Simulated data sets across various models are employed to demonstrate the statistical performance of the estimator, showcasing its ability to reduce bias and provide accurate 95% confidence intervals. Real data sets are also utilized to illustrate the practical application of the proposed approach.

Vaccination represents the historical milestone in medical sciences, which has been saving millions of lives. Nonetheless, continued outbreaks of emergent infectious diseases are swamping from every coast to every border all over the world. Modern vaccines are our most powerful arsenals to defend the public health of a global population ever since 1796. As unexpected, modern vaccination approaches have brought out all sorts of unwelcome pathogenic disorders to varying extents. Pathogenic viruses have also continued to evolve to defeat elaborate arsenals devised by human intelligence. In this review, we have covered a variety of vaccination approaches along with their sophisticated materials from the past to the most recent development. Furthermore, we discuss varied serious pathogenic outcomes elicited by contemporary vaccination programmes involving novel materials in real clinical trials. The complex immune mediators will be discussed in the context to tackle the complication of vaccine-induced pathogenesis. We will offer the insight into the intractable discrepancy of vaccine-associated pathology. The precision approach bestowed with evolutionary concepts will be considered as a feasible option to confront various issues of pathogenic complicacy.

Background: miRNA-122 has been reported to be a useful tool for monitoring ACR after LT. IL-28B SNP rs8099917 genotype is known to contribute to the control of HCV infection. We sought to investigate the relationship between IL-28B SNP rs8099917 genotype and miRNA-122 expression and immune mechanism of ACR after LT using hepatitis C antibody calibration. Patients and Methods: A total of 45 patients with chronic hepatitis C received LDLT. IL-28B SNP rs8099917 genotyping was used to divide TT and GT groups. The relative expression levels of miRNA-122 were calculated by quantitative PCR as 2[(Ct of miR-122) (Ct of U6)] normalized to a reference gene and compared to a control sample, and the anti-HCV titers before and after LT were tracked to observe the relationship with ACR. Results: In the genotype of rs8099917, TT was significantly more associated with higher serum miRNA-122 levels than GT (p = 0.029). The ACR was significantly higher in genotype TT than in GT (p = 0.002). TT was significantly associated with low levels of pre-LT anti-HCV compared with GT (p = 0.022). Multivariate analysis with 95% confidence intervals showed a significant association between rs8099917 genotype TT, lower pre-LT and higher post-LT anti-HCV and ACR. Conclusion: Based on our current data, IL-28B SNP rs8099917 genotype TT may express higher miRNA-122 and correlate with lower Pre-LT and higher Post-LT anti-HCV titers, and may correlate to the pathogenesis of ACR after LT.

Since the implementation of the Materials Genome Project by the Obama administration in the United States, the development of various computational materials databases has fundamentally expanded the choices of industries such as materials and energy. In the field of thermoelectric materials, the thermoelectric figure of merit ZT quantifies the performance of the material. From the viewpoint of calculations for vast materials, the ZT values are not easily obtained due to their computational complexity. Here, we show how to build a database of thermoelectric materials based on first-principles calculations for the electronic and heat transport of materials. Firstly, the initial structures are classified according to the values of bandgap and other basic properties using the clustering algorithm K-means in machine learning, and high-throughput first principles calculations are carried out for narrow-bandgap semiconductors which exhibiting potential thermoelectric application. The present framework of calculations mainly includes deformation potential module, electrical transport performance module, mechanical and thermodynamic properties module. We have also set up a search webpage for the calculated database of thermoelectric materials, providing searching and viewing the related physical properties of materials. Our work may inspire the construction of more computational databases of first-principle thermoelectric materials and accelerate research progress in the field of thermoelectrics.

The research fills the policy research gap for the women entrepreneurship and sustainability performance for examining key successful factors. Previous women entrepreneurship research fails to offer policy recommendations. The research purpose is to investigate these factors affect women entrepreneurship capabilities and sustainability performance by using SEM analysis and making policy recommendation. This research employs online and mail survey and obtains 175 women entrepreneur sample. The study finds that family support and motivation have positive effect on women entrepreneurship capabilities and sustainability performance. Barriers have no effect on performance. Hopefully, the research can provide the guidance to contribute to women’s entrepreneurship opportunities for achieving SDGs. Policy recommendation and managerial implication are discussed in the article.

The oncologic merits of laparoscopic technique for colorectal cancer surgery remain debatable. Eligible patients with non-metastatic colorectal cancer who were scheduled for an elective resection by only one surgeon in a medical institution were randomized to either laparoscopic or open treatment. During this period, total 188 patients received laparoscopic surgery and other 163 patients to open approach. The primary endpoint was cancer-free 5-year survival after operative treatment and secondary endpoint was the tumor recurrence incidence. We found there was no statistically significant difference between open and laparoscopic groups regarding average number of lymph nodes dissected, overall mortality rate, cancer recurrence rate or cancer-free 5-year survival. Nevertheless, laparoscopic approach was more effective for colorectal cancer treatment with shorter hospital stay and less blood loss despite operation time was significantly longer. Meanwhile fewer patients receiving laparoscopic approach developed postoperative urinary tract infection, wound infection, pneumonia or anastomosis leakage, which reached statistical significance. For non-metastatic colorectal cancer patients, laparoscopic surgery resulted in better short-term outcomes whether in total complications and intra-operative blood loss. Though there was no significant statistical difference in terms of cancer-free 5-year survival and tumor recurrence, we favor patients receiving laparoscopic surgery if not contraindicated.

Technology can be seen everywhere and has been integrated into our lives.We are always using technology and enjoying the convenience brought by technology. However, physical retailers and e-commerce companies are also gradually adopting advanced technologies. Technology improves the purchasing environment and purchasing experience. Virtual reality and augmented reality have been hotly discussed in recent years. Technology, although virtual reality and augmented reality technology have not yet matured, it can be said that they will in the future It has great development potential. Virtual reality and augmented reality are also beginning to sprout in the retail industry. However, research on the acceptance of the use of virtual reality and augmented reality in the apparel shopping process is still lacking because This study explores how usefulness, ease of use, hedonicity, customer experience, customer engagement and satisfaction. To influence customer loyalty, this study adopted questionnaire survey and convenience sampling methods, and collected a total of 308 valid questionnaires. The analysis method used confirmatory factor analysis and structural equation model to verify the research hypothesis relationship. The results of this study found. Hedonic has a significant impact on customer loyalty, while usefulness, ease of use, customer experience, customer engagement and satisfaction Satisfaction does not have a significant impact on customer loyalty. This study explains the academic contribution of the research results. The practical implications in marketing are put forward, and specific suggestions and directions for future research are given.

Despite huge effort has been devoted to the design of the initiators and reaction conditions, it remains challenging to synthesize high molecular weight polypeptides with conventional solution phase synthesis. In this work, surface-initiated vapor deposition polymerization (SI-VDP) was utilized to graft synthetic polypeptides poly (γ-benzyl L-glutamate) (PBLG) from polystyrene (PS) resin beads by ring-opening polymerization of N-carboxyanhydrides (NCAs). It was demonstrated for the first time that high molecular weight bulk PBLG (> 500,000) could be readily obtained within one hour via solvent-free synthetic method which paves the way for the synthesis of copolypeptides with high molecular weight.

Surface Plasmon Resonance (SPR) technology has been known as a powerful tool for studying biomolecular interactions because it offers real-time and label-free multiparameter analysis with high sensitivity. This article summarizes the results that have been obtained from the use of SPR technology in studying the dynamics of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) mutations. This paper will begin by introducing the working principle of SPR and the kinetic parameters of the sensorgram which include the association rate constant (ka), dissociation rate constant (kd), equilibrium association constant (KA), and equilibrium dissociation constant (KD). At the end of the section, we will summarize kinetic data on the interaction of SARS-CoV-2 with different variants with various ligands which were obtained from the results of SPR signal analysis. These affinity-related kinetic data are very useful both in drug discovery for therapeutic purposes and in the detection of SARS-CoV-2.

It is a truism that whole energy system models underpin the development of policies for energy system decarbonisation. But recent reviews have thrown doubt on the appropriateness of such models for addressing the multiple goals for future energy systems, in the face of emergent real-world complexity and the evolution of stakeholder’s priorities. Without an understanding of the changing priorities of policy makers and expectations of stakeholders for future systems, system objectives and constraints are likely to be ill-defined, and there is a risk that models may be inadvertently instrumentalised. Adopting a system architecture perspective, the authors have undertaken a three-year programme of research to explore strategies for decarbonising heat in the UK, with interaction with and elicitation of needs from stakeholders at its heart. This paper presents the procedure, methods, and results of an exercise in which experts from stakeholder organisations across the energy system were interviewed. Analysis of interview data reveals two broad approaches to heat decarbonisation which can be broadly defined as either adaptive or transformative. Specific insights gained from these interviews enabled our modelling teams to refocus their work for exploration with a wider circle of stakeholders. Results suggests that this iterative approach to formalising model-policy interaction could improve the transparency and legitimacy of modelling and enhance its impact on policy making.

Bone drilling is a common procedure used to create pilot holes for inserting screws to secure implants for fracture fixation. However, dis process can increase bone temperature, teh excessive heat can lead to cell death and thermal osteonecrosis, potentially causing early fixation failure or complications. We conducted a three-dimensional dynamic elastoplastic finite element model to evaluate teh propagation and distribution of heat during bone drilling and assess teh thermally TEMPeffected zone (TAZ) dat may lead to thermal necrosis. dis model investigates teh parameters influencing bone temperature during bone drilling, including drill diameter, rotational speed, feed force, and predrilled hole. Teh results indicate dat our FE model is sufficiently accurate in predicting teh temperature rise TEMPeffect during bone drilling. Teh maximum temperature decreases exponentially wif radial distance. When teh feed forces are 40 and 60 N, teh maximum temperature does not exceed 45 °C. However, wif feed forces of 10 and 20 N, both teh maximum temperature exceeds 45 °C wifin a radial distance of 0.2 mm, indicating a high-risk zone for potential thermal osteonecrosis. Wif teh two-stage drilling procedure, where a 2.5 mm pilot hole is pre-drilled, teh maximum temperature can be reduced by 14 °C. dis suggests dat higher feed force and rotational speed and/or using a two-stage drilling process could mitigate bone temperature elevation and reduce teh risk of thermal osteonecrosis during bone drilling.

Sinulariolide, a natural product extracted from cultured-type soft coral Sinularia flexibilis, possesses bioactivity against the movement of several types of cancer cell. However, the molecular pathway of its effects on human bladder cancer remain poorly understood. Using a human bladder cancer cell line as an in vitro model, this study investigated the underlying mechanism of sinulariolide against cell migration/invasion in TSGH-8301 cells. We found that sinulariolide inhibited TSGH-8301 cell migration/invasion, and the effect was concentration-dependent. Furthermore, the protein expressions of matrix metalloproteinases (MMPs) MMP-2 and MMP-9, as well as urokinase, were significantly decreased after 24-h sinulariolide treatment. Meanwhile, the increased expressions of tissue inhibitors of metalloproteinases (TIMPs) TIMP-1 and TIMP-2 were in parallel with an increased concentration of sinulariolide. Finally, the expressions of several key phosphorylated proteins in the mTOR signaling pathway were also downregulated by sinulariolide treatment. Our results demonstrated that sinulariolide has significant effects against TSGH-8301 cell migration/invasion, and its effects were associated with decreased levels of MMP-2/-9 and urokinase expression, as well as increased TIMP-1/TIMP-2 expression. The inhibitory effects were mediated by reducing phosphorylation proteins of the PI3K, AKT and mTOR signaling pathway. The findings suggested that sinulariolide is a good candidate for advanced investigation with the aim of developing a new drug for the treatment of human bladder cancer.

To determine the fracture rate of ceramic crowns and causes of ceramic crown failure, this study used keywords—namely “endocrown,” “veneered fixed dental prosthesis,” “monolithic lithium disilicate (LS2),” and “all-ceramic single crown”—to search for articles published in English from 2005 to 2023 in the PubMed electronic database. Rather than using the Boolean logic algorithm between MESH terms and keywords, we accurately calculated the numbers of final clinically tracked cases with crown fractures from the contents of articles. The titles and abstracts of many related articles focused on implant or abutment fracture, while crown fracture was investigated and mentioned only in the main texts of the articles. Our studies included those crowns as well as having more complete data collection. Our search yielded 228, 93, 404, and 358 articles for the keywords “endocrown,” “veneered fixed dental prosthesis,” “monolithic lithium disilicate (LS2),” and “all-ceramic single crown,” respectively. We used the Newcastle–Ottawa Scale (NOS) to assess article quality, and our inclusion criteria were randomized controlled trials (RCT) and cohort study articles involving more than 3 years of follow-up and more than 20 cases. After reviewing, 16 high-quality articles were selected for analysis. The 4.4% crown fracture rate recommended on the basis of most clinical results was achieved in only 6 of the 16 articles. In these 6 articles, the researchers concluded the following reasons that may cause the crown fractures: the thickness of the veneer ceramic material; the connector dimensions; pontic span of the fixed prosthesis; the type of cement; the treatment of the ceramic surface before luting. Other articles inferred that the computer-aided design libraries that were insufficient for the creation of appropriate anatomically supported frameworks for prostheses with ceramic veneers; the thermal expansion coefficient and fracture toughness of the framework material did not match those of the veneer ceramic, resulting in an insufficient area supporting the ceramic veneer then leads to premature crown failure after a long period chewing. The future prospective for material developing could focus on solving those problems and have better clinical results.

3D Zernike moments based on 3D Zernike polynomials have been successfully applied to the field of voxelized 3D shape retrieval and have attracted more attention in biomedical image processing. As the order of 3D Zernike moments increases, both computational efficiency and numerical accuracy decrease. Due to this phenomenon, a more efficient and stable method for computing high-order 3D Zernike moments was proposed in this study. The proposed recursive formula for computing 3D Zernike radial polynomials combines the recursive calculation of spherical harmonics to develop a voxel-based algorithm for the calculation of 3D Zernike moments. The algorithm was applied to the 3D shape Michelangelo's David with a size of 150×150×150 voxels. As compared to the method without additional acceleration, the proposed method uses a group action of order sixteen orthogonal group and saving unnecessary iterations, the factor of speed-up is 56.783±3.999 when the order of Zernike moments is between 10 and 450. The proposed method also obtained an accurate reconstructed shape with the error rate (normalized mean square error) of 0.00 (4.17×10^-3) when the reconstruction was computed for all moments up to order 450.

Elevation has been a cornerstone of biodiversity research, and changes in the environmental factors behind it influence biodiversity and community patterns. Exploring the potential reasons behind liverwort community patterns has been a matter of multiplied interest for ecologists. In the present study, we assessed the liverwort plants of the Sygera Mountain from 3100 m to 4500 m decaying wood, tree, soil, and rock using complex field surveys in 2017 and 2019, and investigated the effects of altitude and various climatic factors on the diversity and community composition of the Sygera Mountain. Also, we used including ANOVA, mixed effects modeling, NMDS, ANOSIM, and CCA, which helped to critically assess the liverwort diversity with respect to environmental variables. The results of the study showed a bimodal variation in the richness of liverwort communities with altitude, with peaks occurring at 3500 m and 4100 m. The variation with altitude was significant, with communities at 4100 m and 4300 m being associated with arid environments, and those at 3100 m and 3300 m favoring areas of higher mean annual temperatures and precipitation. Among the climatic factors, the variation in mean diurnal rang, precipitation, and annual temperature was found to be the determinant of liverwort communities. The results suggest that elevation and daily temperature fluctuations play a crucial role in the distribution and community structure formation of mountain liverwort plants. This study deepens our understanding of liverwort ecology and emphasizes the importance of climatic variables in determining plant community composition.

Mining wastes generate a high environmental impact, and population exposure to metals and metalloids. Phytoremediation is a technology that uses plants to remediate polluted sites, one of its limitations is seed germination in soil with high content of metals and metalloids. B. dactyloides is a native specie from semiarid regions, while C. dactylon is an introduced specie, both are tolerant to drought and low temperatures. Owing, the objective of this research was to evaluate the germination of both species, exposed to a multi-polluted soil with As, Cd, Pb and Zn of a mining site, pondering different pH conditions (from 5.0 to 9.0). The study considered 4 repetitions by type of seed and soil pH. B. dactyloides showed higher germination percentage (83%) with pH 7.8; while the greater germination of C. dactylon was 34 % at pH 6.0. In the soil at pH 5, the germination in both species was not reached, owing that metals are more bioavailable in an acid environment. C. dactylon is less tolerant to As, Cd, Pb and Zn, so it is considered not effective for phytoremediation process. B. dactyloides has a high phytoremediation potential for multi-polluted sites, but further experiments are needed.

Often, engineers with machining experience often judge machining state and tool life according to chips’ features. Engineers' experience is digitized in this study. During the cutting process, the cutting tool coming in contact with the workpiece produces a shear zone, which causes plastic deformation and shear slip. The chips closest to the shear zone can directly show the state of the tool and workpiece when the material is SKD61. This study used chip color, vibration, and current signal integration for prediction of machining state and cutting tool life. When the cutting tool wears increased, the chip surface color changed in the following way: purpleè purple blueè blue ècyan, or even green and yellow. When the cutting tool was in the accelerating wear phase, the color change was particularly obvious. The Back-Propagation Levenberg–Marquardt (BP-LM) predictive methodology was used to compare the predictive ability of voltage, vibration signal, and chip color. The Mean Absolute Percentage Error (MAPE) for the voltage signal was 12.28%, for the vibration signal it was 11.38%, and for the chip color combined with multi-sensor characteristics it was 7.85%. The MAPE of the chip color was the smallest. Using the General Regression Neural Network (GRNN) methodology, the MAPE for the voltage signal was 10.74%, for the vibration signal 7.96%, and for the chip color combined with multi-sensor characteristics was 6.59%. The MAPE of the chip color was the smallest. Obviously, the chip color combined with multi-sensor signals provided better predictive results than the vibration signal or voltage signal alone. There is currently no research on the usefulness of monitoring chip color for tool life prediction.

One of the most important sources of energy is the sun. Taiwan is located at north 22-25° latitude. Due to its proximity to the equator, it experiences only a small angle of sunlight incidence. Its unique geographical location which can obtain sustainable and stable solar resources. This study takes research on the forecast of solar radiation to maximize the benefits of solar power generation, and develops methods that can predict the future solar radiation pattern to help reduce the costs of solar power generation. This study builds supervised machine learning models, known as deep neural network (DNN) and long short-term memory neural network (LSTM). The hybrid supervised and unsupervised model, namely cluster-based artificial neural network (k-means clustering and fuzzy C-means clustering-based models), was developed. After establishing these models, the study evaluated their prediction results. For different prediction periods, the study selected the best-performing model based on the results and proposed combining them to establish a real-time updated solar radiation forecast system capable of predicting the next 12 hours. The study area covered Kaohsiung, Hualien, and Penghu in Taiwan. Data from ground stations of the Central Weather Administration, collected between 1993 and 2021, as well as the solar angle parameters of each station, were used as input data for the model. The results of this study show that different models have their advantages and disadvantages in predicting different future times. Therefore, the hybrid prediction system can predict future solar radiation more accurately than a single model.

The bay is a space barrier for the development of island-type cities and a high-quality waterfront landscape resource. This study takes Xiamen a typical island city in China as an example. First, It use the method of satellite telemetry technology combined with GIS software and spatial syntax, respectively, from the material space level and social space level, to summarize the rapid urbanization process of this city since 1990-2018, focusing on the construction process of three large-scale waterfront park systems in the transition period of inter-island development in it, and comparing the similarities and differences of their spatial forms. Further, from the choice of the axis model and the integrated analysis results, we discuss the spatial efficiency changes. The construction of the three major bay waterfront park systems in this city reflects a huge change in development pattern from lagging construction, synchronous planning, to advanced layout, providing a continuous and variable spatial form for the development of the bay region and improving space efficiency, which one of the important ways to develop and transform island-type cities. We hope to provide the reference for the development including sustainable development of other island cities around the world

Carnivore protoparvovirus 1 (CPPV-1) is a DNA virus causing gastrointestinal disease and immunosuppression in various terrestrial carnivores. Domestic dogs and cats are considered the primary CPPV-1 reservoirs. The habitat overlaps of wild carnivores and free-roaming dogs increases the threat of CPPV-1 transmission between them. This study explored the CPPV-1 distribution among wild carnivores through PCR screening and compared the DNA sequences of the partial capsid protein (VP2) between wild and domestic carnivores. In total, 181 samples were screened for the CPPV-1 VP2 gene, including 32 masked palm civets (Paguma larvata), 63 Chinese ferret badgers (Melogale moschata), and 86 crab-eating mongooses (Herpestes urva), from 2015 to 2019 in Taiwan. The average prevalence of CPPV-1 was 17.7% (32/181), with the highest prevalence in masked palm civets (37.5%). In addition, a masked palm civet was coinfected with two CPPV-1 strains. Among the 33 partial VP2 gene sequences, 23 were identical to sequences amplified from domestic dogs and cats in Asia and the remaining 10 were identified for the first time. This study demonstrated that CPPV-1 has circulated between domestic and wild carnivores in rural Taiwan. Therefore, further population control and health management of free-roaming domestic carnivores are recommended.

The present study examined and compared the effects of high- and low-molecular weight (MW) chitosan, a nutraceutical, on intestinal and liver lipid metabolism in rats fed with high-fat diet. Both high- and low-MW chitosan decreased liver weight, elongated small intestine, improved the dysregulation of blood lipids and liver fat accumulation, and increased fecal lipid excretion in high-fat diet-fed rats. Supplementation of both high- and low-MW chitosan significantly inhibited the decreased phosphorylated AMP-activated protein kinase (AMPK)α and peroxisome proliferator-activated receptor (PPAR)α protein expressions and the increased lipogenesis/cholesterogenesis-associated protein expressions (sterol regulatory element binding protein (SREBP)1c, SREBP2, and PPARγ) and the decreased apolipoprotein (Apo)E and microsomal triglyceride transfer protein (MTTP) protein expressions in the livers of high-fat diet-fed rats. Both high and low-MW chitosan supplementation could also suppress the increased MTTP protein expression and the decreased angiopoietin-like protein (Angptl)4 protein expression in the intestines of high-fat diet-fed rats. Comparison between high and low-MW chitosan, high-MW chitosan has a higher efficiency than low-MW chitosan on the inhibition of intestinal lipid absorption and the increase of hepatic fatty acid oxidation, which can improve liver lipid biosynthesis and accumulation.

Arsenic trioxide (ATO) is now part of the standard regimen for the treatment of newly diagnosed and relapsed acute promyelocytic leukaemia. The availability of an oral form of ATO has greatly reduced the incidence of cardiotoxicity as compared to intravenous administration. Increasing evidence suggests that ATO has anti-inflammatory properties that may be useful for the treatment of autoimmune diseases. These include the modulation of Treg cell activation, Th1/Th2 and Th17/Treg balance, depletion of activated T cells and plasmacytoid dendritic cells, and influence of B cell differentiation, leading to reduced autoantibody and cytokine production. ATO has also been shown to induce apoptosis of activated fibroblast-like synoviocytes through generation of reactive oxygen species and alter the gut microbiota in collagen-induced arthritis. Despite the emergence of newer treatment modalities, the treatment of systemic lupus erythematosus (SLE), especially refractory manifestations, remains a challenge, owing to the paucity of effective biological and targeted therapies that are devoid of adverse effects. Oral ATO is an attractive option for the treatment of SLE because of the lower cost of production, convenience of administration and reduced cardiotoxicity. This article summarizes the anti-inflammatory mechanisms of ATO and its potential application in the treatment of SLE.

Super Typhoon Saola came very close to Hong Kong on 1 and 2 September 2023, necessitating the issuance of No. 10 hurricane signal, the highest tropical cyclone warning signal, in Hong Kong. While there were widespread damages in Hong Kong, no people were killed in the event with effective early warning. It is rare that a super typhoon came very close to Hong Kong and this paper is the first part in the series of the documentation of Saola to summarize the interesting observations of Saola near Hong Kong for future reference by weather forecasters, including sur-face observations, upper air observations, microburst alert from weather radars, and turbulence intensity based on spectral width measurement of radars.

Large quantities of clothing are routinely discarded, ending up in landfills that contribute to the environmental crisis; hence, it is worthwhile investigating how to dispose of this waste in a sustainable way. This study considered environmental values and prosocial behavior from a behaviorism theory. The aim was to set up an environmental protection model for the sustainable disposal of consumer clothing. A structural equation modeling analysis of 407 undergraduate and postgraduate consumer data in Taiwan revealed that consumers’ choice to donate clothing was influenced by environmental values and prosocial behaviors. Clothing resale was influenced by the factor of prosocial behavior. However, prosocial consumers used other disposal patterns instead of resale. Clothing reuse was not influenced by either environmental values or prosocial behavior. The results indicated that environmental values and prosocial behavior did in fact influence consumers’ choices regarding clothing donation. However, prosocial consumers used other disposal patterns instead of resale. Behaviorism theory model is effective in analyzing the factors influencing sustainable clothing disposal. To face clothing waste issues, one can intensify traditional values of industriousness and thriftiness, of compassion and sympathy to others, to accelerate the promotion of the sustainable disposal of clothing.

This paper aims the automatic ball balancers (ABBs) used in passive balancing devices for suppressing vibration of the eccentric rotor. The system model describes which equipped with a skew-mounted ABB with angular deviation. The dynamic equilibrium equations of the system are deduced from the perspective of three-dimensional (3D) dynamics. The results obtained are consistent with those derived from the Euler-Lagrange equations. It is exciting that the spatial dynamics method reveals the spatial geometric characteristic of dynamic balance positioning of the balls when the system is balanced with vibration suppression. The spatial property emerges the perpendicular line from each ball to the rotating spindle of the system must pass through the central axis of the orbit perpendicular to the ABB plane. This characteristic is a general rule that can be used to explain the phenomenon of the stable equilibrium positions of the balls in all previously studied cases.

The fluctuations in both time and space of the fish larvae community in relation to hydrographic characteristics in the waters surrounding the Taiwan Bank were studied in October 2021 (autumn) and March 2022 (spring). Throughout the study period, we identified a total of 149 taxa of fish larvae, encompassing 96 genera and 71 families. Engraulis japonicus, Diaphus slender type, unidentified Gobiidae, Apogon sp., unidentified Clupeidae, and Benthosema pterotum were the six most dominant taxa, together constituted 47.39% of the total catch. No significant temporal difference in abundance of fish larvae was found, but the species number of fish larvae was more diverse in spring than in autumn. There was a notable difference in species composition between the cruises, and the cluster analysis unveiled a distinct temporal structure in the assemblage of fish larvae. The dynamics of prevailing currents induced by seasonal monsoons play an important role in the transport of fish larvae. The distribution of fish larvae was closely linked to hydrographic features, where seawater temperature and salinity emerged as the primary explanatory factors influencing the composition of fish larvae assemblages in the waters surrounding the Taiwan Bank. While the increased influx of nutrients from upwelling ensures abundant food availability, the hydrographic conditions may not be suitable for every fish larva.

The nucleation of voids in alpha iron and the influence of carbon were investigated through a combination of rate theory and nucleation theory calculations. The steady rates of void nucleation exhibit high sensitivity to carbon. Even a seemingly negligible carbon concentration, as low as a few atomic parts per million (appm), can dramatically reduce the nucleation rates and narrow the temperature window for nucleation. This study highlights the challenges in certifying and qualifying nuclear materials for use in reactor environments. It emphasizes the necessity for precise control of impurity levels during materials processing and stringent requirements for irradiation testing, which are susceptible to contamination. Furthermore, the study provides an explanation for the significant data scattering observed in void swelling behaviors as reported in the literature.

The state of the grinding wheel in the grinding process directly affects the surface quality of the workpiece. The monitoring of the wear state of the grinding wheel can effectively identify the wear information of the grinding wheel and timely and effectively repair the grinding wheel. In this paper, a multi-sensor fusion precision grinding wheel wear intelligent monitoring system is established for typical difficult-to-machine aerospace material titanium alloy, and a multi-eigenvalue fusion algorithm based on improved support vector machine (SVM) is proposed. The extracted sound emission signal wavelet packet decomposition coefficient mean square value, force signal grinding force ratio, and vibration signal effective value are used as the input of the improved support vector machine, and the identification strategy is adjusted by the entropy weight evaluation method. The results show that the monitoring system established in this paper can effectively identify the wear state of the grinding wheel, and the monitoring accuracy can reach more than 92%.

Pastes containing reduced graphene oxide (rGO) and LiCl-Mn(NO3)2·4H2O are screen-printed on a carbon cloth substrate and then calcined using a nitrogen atmospheric-pressure-plasma jet (APPJ) for conversion into rGO-LiMnOx nanocomposites. The APPJ processing time is within 300 s. RGO-LiMnOx on carbon cloth is used to sandwich H2SO4, LiCl, or Li2SO4 gel electrolytes to form hybrid supercapacitors (HSCs). The areal capacitance, energy density, and cycling stability of the HSCs are evaluated using electrochemical measurement. The Li2SO4 gel electrolyte HSC exhibits the highest areal capacitance and energy density but lower cycling stability. By contrast, the H2SO4 gel electrolyte HSC exhibits better cycling stability but lower areal capacitance and energy density.

This study focuses on the impact of weak partial discharges (PDs) on defect recognition accuracy in epoxy resin through phase-resolved partial discharge (PRPD) analysis. Two measurement conditions are compared until PRPD pattern saturation: one-minute and one-hour durations. The PD data specifically target three void types located at different positions within the epoxy material. The aim is to evaluate how the presence of weak PDs at the PD extinction voltage (PDEV) influences defect recognition accuracy. This research sheds light on the potential implications of neglecting the significance of weak PD signals in defect detection. A convolutional neural network (CNN) model is trained using PRPD data recorded at the PD inception voltage (PDIV) and tested using the new PRPD data from both conditions recorded from a lower PDIV to a PDEV. The trained CNN model achieves a defect recognition accuracy of 100% for a one-hour duration, highlighting the importance of not neglecting weak PD signals. This emphasizes the significance of extended measurement duration and pattern saturation in capturing and analyzing weak PD signals for improved defect recognition. This study contributes to the advancement of practical applications by understanding the behavior of the epoxy material and enhancing defect detection techniques.

The standard treatment for early-stage lung cancer is complete tumor excision by limited resection of the lung. Pre-operative localization is used before video-assisted thoracoscopic surgery (VATS) to improve the accuracy of pulmonary nodule excision. However, lung atelectasis and hypoxia resulting from controlling apnea during the localization procedure may affect the localization accuracy. Pre-procedural pulmonary recruitment may improve respiratory mechanics and oxygenation during localization. In this study, we investigated the potential benefits of pre-localization pulmonary recruitment prior to pulmonary ground-glass nodule localization in a hybrid operating room. We hypothesized that pre-localization pulmonary recruitment would increase localization accuracy, improve oxygenation, and prevent the need for re-inflation during the localization procedure. We retrospectively enrolled patients with multiple pulmonary nodule localizations before surgical intervention in our hybrid operating room. We compared localization accuracies between patients who had undergone pre-procedure pulmonary recruitment and patients who had not. Saturation, re-inflation rate, apnea time, procedure-related pneumothorax, and procedure time were also recorded as secondary outcomes. Patients who had undergone pre-procedure recruitment had better saturation, shorter procedure time, and higher localization accuracy. The pre-procedure pulmonary recruitment maneuver was effective in increasing regional lung ventilation, leading to improved oxygenation and localization accuracy.

In the mold machining process, the cutting tool is worn with machining time, thereby affecting the surface accuracy, leading to poor workpiece dimensions, even fracture. At present, many studies have used multiple sensors to detect the machining conditions of cutting tool and workpiece, including indirect measurement method and direct measurement method. The indirect measurement method, which has been studied widely, mainly uses sensors to capture signals for subsequent data analysis; the direct measurement method mainly analyzes the state of cutting shear zone. Due to the cut-in of cutting tool in the machining process, the workpiece is dislocated rapidly, generating considerable amount of heat, which is transferred to the chips, inducing color change on the surface of chips. Many engineers with machining experience often judge the machining state and tool life according to the chips. The engineers' experience is digitized in this study, and indirect measuring sensors are used to predict the tool life, so as to attain the objective for smart manufacturing, the average percentage error of MAPE using single vibration and voltage eigenvalues as input features is 10%, the voltage signal characteristic values and vibration signal characteristic values are combined. Finally, the chip surface chromaticity eigenvalue is combined with signal characteristic value. The average prediction error of BP-LM method is 7.85%, the average prediction error of GRNN method is 6.59%. Therefore, when the eigenvalue of chip surface chromaticity is added to the prediction result, it can enhance the accuracy of cutting tool wear value prediction more effectively than single sensor signal characteristic value.

A twin-screw extruder was used to fabricate poly(butylene succinate) (PBS)/high density polyethylene (HDPE) blends (7:3 weight ratio) and blend-based nanocomposites. Carbon nanotubes (CNTs), graphene nanoplatelets (GNPs) and organoclays (15A and 30B) served as the nanofiller, while maleated HDPE (PEgMA) acted as an efficient compatibilizer for the blend. In the composites, individual nanofillers were mostly localized in HDPE domains, but some fillers were also observed at PBS-HDPE interfaces. The sea-island morphology of compatibilized blend evolved into a pseudo-co-continuous morphology in the composites. Differential scanning calorimetry results confirmed that PEgMA with HDPE evidently accelerated the crystallization of PBS in the blend. The possible nucleation effect of added fillers on PBS crystallization was obscured by the formation of quasi-connected HDPE domains, causing less PBS nucleation sites. The presence of nanofillers improved the thermal stability and burning anti-dripping behavior of the parent blend. The anti-dripping efficiency of added fillers followed the sequence: CNT>15A>30B>GNP. Rigidity of the blend was increased after formation of nanocomposites. In particular, adding GNP resulted in 31% increase in flexural modulus. Development of a pseudo-network structure in the composites was confirmed by measurement of rheological properties. Electrical resistivity of the blend was reduced by more than 6 orders of magnitude at 3 phr CNT loading, demonstrating the achievement of double percolation morphology.

The research aims to examine the extent to which the perceived organizational support (POS) predicted career related self and environmental exploration via the mediation effect of career adaptability. Multi-group comparisons based on the gender, majors and places of origin were also performed to evaluate the differences among these variables. An internet survey was conducted to collect empirical data from 611 Chinese undergraduates. Structural equation modeling (SEM) was conducted to demonstrate the proposed relations in the model and multiple group analysis. Clearly supported was the direct relations between POS and career related self and environmental exploration and the mediation effect of career adaptability. The results also showed that gender and major are the moderating variables for the proposed model, and no significance difference among the rural and urban subgroups was found. POS could be effectively delivered to students in general, marginalized social groups, such as females and those majored in the humanities and social sciences in particular. Four dimensions of career adaptability (concern, control, curiosity and confidence) could also be targeted at in order to promote students’ sustainable employment. The findings provide a better understanding of the career construction model by incorporating the contextual factor in a collective cultural environment.

Shape Memory Alloy (SMA) have emerged as a revolutionary material that holds the potential to change the design and construction methods of buildings and other structures. One of the most promising applications of SMAs in civil engineering is their use as reinforcements for steel structures. This paper presents the latest research progress, opportunities and challenges of SMA in the field of steel structural reinforcement, both in terms of basic components and applications. In terms of components, the construction forms and working mechanisms of Fe-SMA strips, SMA/CFRP composite patches and SMA dampers are introduced. On this basis, the application of SMA in steel structures reinforcement is introduced, and its effect is analyzed from three aspects: crack restoration, seismic retrofitting and structural strengthening. Finally, the results of the current research are summarized and the shortcomings are analyzed, hoping to provide a reference for the research of SMA in the field of steel structures reinforcement.

Energy resources are important sources of social and economic development, human survival and security. However, energy resources are objective and scarce, especially the fossil energy, such as coal, oil, natural gas, etc. Human survival environment is increasingly damaged, and the condition of energy is also gradually becoming deficient, so it is necessary to develop new energy resources to meet the increasing demand of material civilization. Solar energy can meet the needs of human development in the future as a kind of clean resource and it has been concerned by all countries in the world. We analyzed the effectiveness of subsidies to the PV industry of both the price and R&D by the spatial econometric model. In some region, the production capacity of photovoltaic industry has shown a significant spatial agglomeration situation in China since 2012. At the same time, benchmarking price and R&D subsidies played a positive incentive to the photovoltaic industry production capacity. It is a certain degree of inverse correlation between the scale of policy subsidies and the resource endowment of solar resources. Therefore, the countermeasures should be considered from the aspects of institutions, industry, technology and public financial policies.

Although good field emission from graphene has been demonstrated from a wide variety of different microfabricated structures, very few of them can be used to improve the design of cold field emitters for electron microscopy applications. Most of them consist of densely packed nano-emitters, which produce a large array of defocused overlapping electron beams, and therefore cannot be subsequently focused down to a single nanometer electron probe. This paper reviews the kind of single-tip cathode structures suitable in cold field emission guns for instruments such as scanning electron microscopy, transmission electron microscope or scanning transmission electron microscopy, and reviews progress in fabricating them from graphene-based materials.

Tumor-associated macrophages (TAMs) play critical roles in the tumor microenvironment (TME), where they are recruited by signals released by cancer cells. Although they have great potential as therapeutic targets for cancer treatment, the dual roles of TAMs in promoting or inhibiting tumor growth, invasion, and metastasis make their function in cancer progression complex. In this review, we provide an overview of the current understanding of TAMs, including their phenotypic diversity, regulatory signaling pathways, and interactions with other cells in the TME. We also discuss the challenges related to the standard isolation protocols of TAMs, inconsistent research results, and translation of TAM knowledge into clinical applications. Additionally, we review the status of clinical trials involving TAMs and potential strategies to overcome the limitations. The future direction of TAM research should focus on developing more targeted therapies that specifically regulate TAM function and non-invasive methods for monitoring TAM activity in cancer patients. A comprehensive understanding of the complex role of TAMs in cancer may lead to the development of more effective treatments and improved outcomes for cancer patients.

In Los Angeles, at one point, the Covid-19 testing positivity rate was 6.25%, or one in sixteen. This translates to, on average, one in sixteen specimens testing positive and the vast majority testing negative. Usually, we run sixteen tests on sixteen specimens to identify the positive one(s). This process can be time consuming and expensive. Since a group of negative specimens pooled together for testing will produce a negative result, one single test could potentially eliminate many specimens. Only when the pooled specimen tests positive do we need further testing to identify the positive one(s). Based on this concept, we designed a strategy that will identify the positive specimen(s) efficiently. Assuming one in sixteen specimens is positive, we find that only four tests are needed. Furthermore, we can run them simultaneously, saving both resources and time. Although, in the real world, we cannot make the assumption of only one positive specimen, the same strategy works with slight modification and proves to be much more efficient than the conventional testing. Our strategy returns an answer 48% of the time in four tests and one time cycle. Overall, the average number of tests is seven or eight depending on the follow-up testing, and the average time cycle is about one and a half.

Using the Yellow-River-Source National Park (YRSNP) as a study site, an unmanned aerial vehicle (UAV) remote sensing and line transect method was used to investigate the number of wild herbivorous animals and livestock, including the kiang (Equus kiang) and Tibetan gazelle (Procapra picticaudata). A downscaling algorithm was used to generate the forage yield data in YRSNP based on 30 m spatial resolution. On this basis, we estimated the forage–livestock balance, which included both wild animals and livestock, and analyzed the effects of functional zone planning in national parks on the forage–livestock balance in YRSNP. The results showed that the estimates of large herbivore population numbers in YRSNP based on population density in the aerial sample strips, which were compared and validated with statistical data and warm season survey results, indicated that the number of kiangs and Tibetan gazelles in the 2017 cold season was 12900 and 12100, respectively. The number of domestic yaks, Tibetan sheep, and horses was 53400, 76800, and 800, respectively, and the total number of sheep units was 353200. The ratio of the number of large wild herbivores and livestock sheep units was 1:5; Large wild herbivores have different preferences for functional zones, preferring ecological restoration areas consisting mainly of degraded grassland; The grazing pressure indices of the core reserve areas and ecological restoration areas were 0.168 and 0.276, respectively, indicating that these two regions still have high grazing potential. However, the grazing pressure index of the traditional utilization areas was 1.754, indicating that these grasslands are severely overloaded; After the planning and implementation of functional zones, the grazing pressure index of YRSNP was 1.967. Under this measure, the number of livestock was not reduced and the grazing pressure nearly doubled, indicating that forage–livestock conflict has become more severe.

Paleopeat-forming environments have an important effect on the dispersion and enrichment of trace elements in coal. The C3 coal seam of the Xuanwei Formation in eastern Yunnan was used as a case study to reconstruct the paleopeat-forming environment based on the coal facies parameters and geochemical characteristics, and its influence on trace element (including rare earth elements and yttrium, REY) enrichment was investigated. The C3 coal was classified as medium rank coking coal with an ultra-low moisture content, medium-high-ash yield, and low-medium volatile content. Compared to the average values for Chinese coals, Cu and V were enriched and Co was slightly enriched in the C3 coal. Compared with the average values for world coals, Cu and V were enriched, while several other trace elements were slightly enriched, including Co, Hf, Nb, Sc, Ta, Zn, and Zr in the C3 coal. The C3 coal was deposited in a low peat mainly limno-telmatic swamp, with deep water, weak hydrodynamic conditions, brackish to salty water, and reducing conditions. Trace elements, including Cu, V, Hf, Nb, Sc, Ta, Zr, and REY, are typically enriched in a limno-telmatic environment with fresh water, and reducing and weak hydrodynamic conditions. Additionally, REY and V are also significantly enriched in brackish water limno-telmatic conditions with the same depositional environment.

The mechanical engineering requires heat treatment after rough machining to reach the mechanical strength, but the heat treatment can induce workpiece deformation, so that the workpiece cannot be reworked. In this study, the plasma was integrated with a lathe, and the on line heat treatment was performed to achieve the mechanical strength and hardness, so as to reduce the machining process and handling. However, for on line heat treatment, it is important to study the machine and plasma parameters of the lathe and plasma, and the research method is used eventually to optimize the process, reduce the machining cost and machining error. The variable factors in surface on line real-time heat treatment are revolution, feed rate and current, the objective function is the hardness of mechanical properties. In the screening experiment, the interaction of factors was discussed using full factorial experiment. The Central Composite Design was combined with the Lack-of-Fit test for optimization experiment, the R2 coefficient was used to determine whether the regression model is appropriate. The optimum parameters were derived from the contour diagram and response surface diagram. The experimental results show that the significant factors include revolution, feed rate and current, the optimum parameters include revolution 168rpm, feed rate 0.068mm/rev and current 86A. The experimental results of optimum parameters show that the surface hardness is increased from 306HLD to 806HLD, the surface hardening effect is enhanced by 163%, so the on line real-time heat treatment equipment has a best hardening effect.

Distributed deformation based on Fiber Bragg Grating sensors or other kinds of strain sensors can be used to evaluate safety in operating periods of bridges. However, most of the published researches about distributed deformation monitoring are focused on solid rectangular beam rather than box girder—a kind of typical hollow beam widely employed in actual bridges. Considering that the entire deformation of a single-cell box girder contains not only bending deflection but also two additional deformations respectively caused by shear lag and shearing action, this paper again revises the improved conjugated beam method (ICBM) based on the LFBG sensors to satisfy the requirements for monitoring two mentioned additional deformations. The best choice for the LFBG sensor placement in box gilder is also proposed in this paper due to strain fluctuation on flange caused by shear lag effect. Results from numerical simulations show that most of the theoretical monitoring errors of the revised ICBM are 0.3%~1.5%, and the maximum error is 2.4%. A loading experiment for a single-cell box gilder monitored by LFBG sensors show that most of the practical monitoring errors are 6%~8%, and the maximum error is 11%.

Streptococcal infection is a main infectious diseases for farmed grey mullet (Mugil cephalus). This study were to identify spreptococcal species in diseased farmed grey mullet and to investigate differences in susceptibility to 13 antibiotics and in genotypes between the stains from the grey mullet and non-grey mullet. 170 samples from diseased farmed grey mullet were collected from three county in 2013 -2016. Multiplex PCR identified L. garviea (146) as the main pathogen, S. agalactia (9), S. dysgalactiae (19), and double infection (5), but no S. iniae. The prevalence changed annually and differed among three counties. Pulsed-field gel electrophoresis (PFGE) analysis demonstrated identical genotype with an ApaI-digested DNA pattern. Disc diffusion results demonstrated differences in antibiotic susceptibility between the strains from grey mullet (146) and non-grey mullet (30). Almost all strains resisted to clindamycin and all strains were susceptible to six antibiotic in grey mullet and 4 antibiotics in non-grey mullet. The reduced susceptible strains was more in non-grey mullet than grey mullet group. The reduced susceptible strains were observed the highest in 2014 and in Chiayi county and decreased from 2014 to 2016. However, the strains with reduced susceptibility to ceftriaxone, cirpofoxacin, moxifloxacin, tetracycline for human treatment were observed.

A 57-year-old male with a history of hyperlipidemia and mild pulmonary hypertension presented for a left inguinal hernia repair. Preoperative electrocardiogram showed severe right axis deviation at 177 degrees and abnormal repolarization. Right ventricular hypertrophy secondary to pulmonary hypertension was the primary differential but was quickly ruled out due to the patient being asymptomatic and having great exercise tolerance. Dextrocardia was also ruled out due to normal progression on the precordial leads. The simultaneous severe right axis deviations of P, R, and T waves raised suspicion for erroneous lead placement. The repeat electrocardiogram confirmed the diagnosis.

Most of the existing influence maximization algorithms are not suitable for large-scale social networks due to their high time complexity or limited influence propagation range. Therefore, a D-RIS influence maximization algorithm is proposed based on the independent cascade model and combined with the reverse reachable set sampling. Under the premise that the influence propagation function satisfies monotonicity and submodularity, the D-RIS algorithm uses automatic debugging method to determine the critical value of the number of reverse reachable sets, which not only obtains a better influence propagation range, and greatly reduce the time complexity. The experimental results on the two real data sets of Slashdot and Epinions show that D-RIS algorithm is close to the CELF algorithm and higher than RIS algorithm, HighDegree algorithm, LIR algorithm and pBmH algorithm in influence propagation range. At the same time, it is significantly better than the CELF algorithm and RIS algorithm in running time, which indicates that D-RIS algorithm is more suitable for large scale social network.

Identifying locations of landslide slip surfaces provides critical information for understanding the volume of landslides and the scale of disasters, which is essential for formulating disaster preparedness and mitigation strategies. Based on hydrogeological survey data from 24 deep-seated landslide-prone sites in Taiwan's mountainous regions, this study first developed the hydraulic conductivity potential index (HCPI) using principal component analysis to quantify hydraulic properties of disturbed rock formation with six geological factors. Then, The regression analysis was performed to construct a permeability estimation model for the geological environment of landslides. Finally, the established model was utilized to develop an identification method for potential slip depths in landslide-prone sites. Results indicated a strong relation between HCPI and hydraulic conductivity with a determination coefficient of 0.895. The relation equation confirmed that its generated data concerning the depths of significant changes in hydraulic conductivity could be used to identify potential slip surfaces. Additionally, this study successfully establishes a rule for identifying potential slip zones by summarizing data concerning the generated hydraulic conductivity profiles, stratigraphic lithology, existing inclinometer slip depth records, and groundwater level of landslide sites. This identification method was then applied to predict potential slip depths for ten landslide sites where slip surfaces have not yet occurred. These findings offer a new alternative to having early information on potential sliding depths for timely disaster management and control implementation.

Taiwan cobra (Naja atra) bites account for approximately 20% of all venomous snakebites in Taiwan. In Taiwan, the rates of wound necrosis and secondary infection from Taiwan cobra bites are higher than those associated with other venomous snakebites. Clinical tools to evaluate the infection risk after Taiwan cobra bites are lacking. Therefore, in this study, we developed a useful clinical tool to evaluate the infection risk after Taiwan cobra bites. Moreover, we investigated wound infection bacteriology. We analyzed the data of patients bitten by N. atra who had undergone freeze-dried neurotoxic antivenin treatment in emergency rooms of the Chang Gung Memorial Hospital network, which comprises seven hospitals and the largest medical system in Taiwan, from January 2001 to May 2017. Because patients with wound necrosis required antibiotics for infection treatment, we included only patients with wound infection but without tissue necrosis in the development of our Cobra Bacteriology of Infections in Taiwanese snake Envenomation (Cobra BITE) score by using univariate and multiple logistic regression. In total, 8,295,497 emergency department visits occurred from January 2001 to May 2017, and 195 patients were diagnosed has having cobra bites. Among them, 23 and 30 patients had wound necrosis and wound infection, respectively. The wound infection rate was 27.2% (53/195). Regardless of whether the patients had necrosis, Enterococcus faecalis and Morganella morganii were the main bacteria identified in the culture report. Gentamicin, ceftriaxone, ciprofloxacin, and levofloxacin are the ideal first-line antibiotics for treating N. atra bite wounds in Taiwan. As per our Cobra BITE score, the three factors predicting secondary wound infection after cobra bites are hospital admission, a white blood cell count (in 103/µL) × by neutrophil–lymphocyte ratio value of ≥114.23, and the use of antivenin medication. The area under the receiver operating characteristic curve for the Cobra BITE score system was 0.88. The ideal sensitivity and specificity were 0.89 and 0.76, respectively, and the optimal cutoff point for Cobra BITE score was 7. The Hosmer–Lemeshow p value was 0.4. In conclusion, our Cobra BITE study established a new practical clinical tool for clinicians to evaluate infection risk after N. atra bites. This score system enables the assessment of wound infections after N. atra bites, and it could be modified and improved in future for other Naja spp. bites.

An automated discharge imaging system (ADIS), a non-intrusive and safe approach, was developed for measuring river flows during flash flood events. ADIS consists of dual cameras to capture complete surface images in the near and far fields. Surface velocities are accurately measured using the Large Scale Particle Image Velocimetry (LSPIV) technique. The stream discharges are then obtained from the depth-averaged velocity (based upon an empirical velocity-index relationship) and cross-section area. The ADIS was deployed at the Yu-Feng gauging station in Shimen Reservoir upper catchment, northern Taiwan. For a rigorous validation, surface velocity measurements were conducted using ADIS/LSPIV and other instruments. In terms of the averaged surface velocity, all measured results were in good agreement with small differences, i.e., 0.004 to 0.39 m/s and 0.023 to 0.345 m/s when compared to those from acoustic Doppler current profiler (ADCP) and surface velocity radar (SVR), respectively. The ADIS/LSPIV was further applied to measure surface velocities and discharges during typhoon events (i.e., Chan-Hom, Soudelor, Goni, and Dujuan) in 2015. The measured water level and surface velocity both showed rapid increases due to flash floods. The estimated discharges from ADIS/LSPIV and ADCP were compared, presenting good consistency with correlation coefficient R = 0.996 and normalized root mean square error NRMSE = 7.96%. The results of sensitivity analysis indicate that components till (τ) and roll (θ) of the camera are most sensitive parameter to affect the surface velocity using ADIS/LSPIV. Overall, the ADIS based upon LSPIV technique effectively measures surface velocities for reliable estimations of river discharges during typhoon events.

In recent years, the demand for coffee has increased tremendously. During the production process, green coffee beans are traditionally screened manually for defective beans before they are packed into coffee bean packages; however, this method is not only time-consuming but also increases the rate of human error due to fatigue. Therefore, this paper proposed a lightweight deep convolutional neural network (LDCNN) for the quality detection system of green coffee beans, which combined depthwise separable convolution (DSC), squeeze-and-excite block (SE block), skip block, and other frameworks. To avoid the influence of low parameters of the lightweight model caused by the model training process, rectified Adam (RA), lookahead (LA), and gradient centralization (GC) were included to improve efficiency; the model was also put into the embedded system. Finally, the local interpretable model-agnostic explanations (LIME) model was employed to explain the predictions of the model. The experimental results indicated that the accuracy rate of the model could reach up to 98.38% and the F1 score could be as high as 98.24% when detecting the quality of green coffee beans. Hence, it can obtain higher accuracy, lower computing time, and lower parameters. Moreover, the interpretable model verified that the lightweight model in this work is reliable, providing the basis for screening personnel to understand the judgment through its interpretability, thereby improving the classification and prediction of the model.

A novel flexible humidity sensor, incorporating gold nanoparticles (Au NPs) and a trifunctional organosilica compound, has been developed through the integration of sol-gel processing, free radical polymerization, and self-assembly techniques. The trifunctional organosilica was initially synthesized by modifying (3-mercaptopropyl)trimethoxysilane (thiol-MPTMS) with 3-(trimethoxysilyl)propyl methacrylate (vinyl-TMSPMA). Subsequently, a hydrophilic polyelectrolyte, [3(methacryloylamino)propyl]trimethyl ammonium chloride (MAPTAC), was grafted onto the MPTMS-TMSPMA gel. The Au NPs were assembled onto the thiol groups present in the MPTMS-TMSPMA-MAPTAC gel network. The compositional and microstructural properties of the Au NPs/MPTMS-TMSPMA-MAPTAC composite film were investigated utilizing Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). The presence of thiol groups and mesoporous silica skeletons ensured the stability of the humidity-sensing film on the substrate under highly humid conditions, while the hydrophilic groups functioned as humidity-sensitive sites. This innovative humidity sensor demonstrated high sensitivity, acceptable linearity, minimal hysteresis, and rapid response time across a broad range of working humidity levels. Based on the complex impedance spectra analysis, hydronium ions (H₃O⁺) were determined to govern the conductance process of the flexible humidity sensor.

This study focuses on a sample of Chinese listed companies from 2019 to 2020 to explore the relationships among corporate social responsibility, financial constraints, and financial performance. In addition, we discuss five factors affecting financial constraints. We also analyze the types of enterprises that can improve their financial performance by implementing corporate social responsibility keeping in mind the factors that lead to a high degree of financial constraint. The results indicate that: 1. The degree of financial constraints has a negative and significant impact on financial performance; 2. There is a reverse relationship between the degree of financial constraints and the effectiveness of corporate social responsibility measures; 3. Enterprises with high financial constraints (due to lower financial slack and revenue growth rates) can significantly improve their financial performance through the implementation of effective corporate social responsibility programs. 4. Enterprises with high financial constraints, caused by financial slack and revenue growth rate, can significantly improve their financial performance by implementing corporate social responsibility programs.

Fitts' law predicts the human movement response time for a specific task by a simple linear formulation, in which the intercept and the slope are estimated from the task's empirical data. This research was motivated by our pilot study, which found that the linear regression's essential assumptions are not satisfied in the literature. Furthermore, the keystone hypothesis in Fitts' law, that the movement time per response will be directly proportional to the minimum average amount of information per response demanded by the particular amplitude and target width, has never been formally tested. Therefore, this study developed an optional formulation derived from fusing the findings in psychology, physics, and physiology for fulfilling the statistical assumptions. An experiment was designed to test the hypothesis in Fitts' law and validate the proposed model. To conclude, our results indicated that movement time could be related to the index of difficulty underlying the same constant amplitude. The optional formulation accompanies the index of difficulty in Shannon form robustly performs the prediction better than the traditional model across studies. Finally, a new approach to modeling movement time prediction is deduced from our research results

The signal processing technique is one of the principal tools for diagnosing power quality (PQ) issues in electrical power systems. The Discrete Fourier Transform (DFT) is a frequency analysis technique used to process power system signals and identify PQ problems. However, the DFT algorithm may lead to spectral leakage and picket-fence effect problems for asynchronously sampled signals that contain harmonic, inter-harmonic, and flicker components. To resolve this shortcoming, a hybrid method for frequency estimation based on a second-level DFT approach and a frequency-domain interpolation algorithm to obtain the accurate fundamental frequency of a power system is proposed in this paper. This method uses a second-level DFT to compute the cosine and sine parts for the fundamental frequency components of the acquired signals. Then, a frequency-domain interpolation approach is adopted to determine the amplitude ratio for the cosine and sine parts of the system's fundamental frequency. To demonstrate the performance of the proposed frequency estimation method, the observation window used by this paper to evaluate different estimation algorithms is 200 ms. According to the IEC standards, a 200 ms acquisition window is recommended for power system quality assessment. A set of mixed signals with harmonic, inter-harmonic, and flicker components with the fundamental frequency deviation is used. The evaluation results demonstrate the superiority of the new method over other approaches for assessing asynchronously sampled signals contaminated with noise, harmonic, inter-harmonic, and flicker components.

A lightweight composite bridge deck system composed of steel orthotropic deck stiffened with thin Ultra-High Performance Concrete (UHPC) layer is developed to eliminate fatigue cracks in orthotropic steel decks. During the construction and operation period of the bridge, the debonding between the steel deck and the UHPC layer may introduce the several issues, such as crack-induced water invasion and distinct reduction of the shear resistance. In the study, an effective and novel non-destructive interface condition monitoring approach using piezoelectric lead zirconate titanate (PZT)-based technologies is proposed to detect interfacial delamination between steel deck and UHPC layer. Experimental tests are performed on several steel-UHPC composite slabs and a conventional steel-concrete composite slab. The thin styrofoam sheets with different sizes and thicknesses are set on different locations of the steel deck as the artificial debondings. The PZT ceramic patches are bonded on the surfaces of the steel deck and UHPC layer as the actuators/sensors. An improved PSO (Particle Swarm Optimization)-K-means clustering algorithms is proposed to obtain the debonding patterns based on the feature data set. The laboratory tests demonstrate that the proposed approach provides an effective and accurate way to detect interfacial debonding of steel-UHPC composite slab.

Consumer IoT (CIoT) manufacturers seek customer feedback to enhance their products and services, creating a smart ecosystem like a smart home. Due to security and privacy concerns, Blockchain-based federated learning (BCFL) ecosystems can let CIoT manufacturers update their Machine Learning (ML) model using end-user data. FL uses privacy-preserving ML techniques to forecast customers' needs and consumption habits, and blockchain replaces the centralised aggregator to safeguard the ecosystem. However, Blockchain technology (BCT) struggles with scalability and quick ledger expansion. In BCFL, local model generation and secure aggregation are other issues. This research contributes a novel architecture emphasising Gateway Peer (GWP) in blockchain network to resolve scalability, ledger optimisation and secure model transmission issues. In the architecture we replace the centralised aggregator by the blockchain network, while GWP restricts the number of local transactions to execute in BCN. Considering the security and privacy of FL processes, we have added differential privacy and advanced normalisation techniques to ML processes. The approaches strengthen end-users' cyber security and encourage the adoption of technological innovation standards by service providers. The proposed approach has been tested extensively using a well-respected Stanford Cars dataset. We experimentally demonstrate that the proposed architecture makes the network scalable and optimises the ledger significantly. In addition, the normalisation technique outperforms batch normalisation when features are under DP protection.

Various colors of clothing originating from synthetic dyes are presently causing serious environmental pollution problems, whereas natural dyes extracted from natural indigo plants help reduce the harm to the environment and extend the sustainable use of clothing. This study focuses on the relation between indigo dyeing colors and the environment on the basis of sustainable design. The results reveal that light colors are considered to conform to the sustainable spirit more than dark colors in different indigo colors. In fact, the recyclable light-colored indigo dyeing t-shirt is beneficial in its reuse. Indigo dyeing fabric can be decomposed by a variety of microorganisms; however, the light-colored indigo dyeing takes a short time. Light colored indigo dyeing is more resource-saving when considering dye, water and electricity costs. The results of colors and environmental protection provide scheme references to consumers or industry for clothing collocation of different indigo dyeing colors for a series of blue clothing and carry out the ideal of the sustainability and co-existence between clothing and natural resources.

Detailed kinetics for a 3-wavelength photopolymerization confinement (PC) system is presented for both numerical solutions and analytic formulas. The dynamic profiles are simulated for oxygen, free radical, and conversion for various situations of: blue-light only, 2-light (red and UV), and 3-light (red, blue, UV). An effective PC requires two conditions: (i) a strong N-inhibition for uncured regime with a low conversion (triggered by the UV-light); and (ii) a weak S-inhibition (oxygen-induced) for high conversion under the blue-light or blue and red-light initiation. Good PC candidates are governed by collective factors of: (i) the double ratio of light-intensity and initiator-concentration, (ii) monomers rate-constant; and (iii) effective absorption constants at specific wavelength and initiators. A new reverse feature for the role of N-inhibition on the blue-conversion is found. Higher oxygen concentration leads to a lower conversion, which could be enhanced by reducing the S-inhibition via a red or blue-light pre-irradiation, having a pre-irradiation time TP=200 s for red-light only, and reduced to 150 s, when both red and blue-light. System under UV-only leads a conversion lower than that of blue-only. However, conversion could be improved by the dual-light (blue and UV), and further enhanced by the pre-irradiation of red-light. The two competing factors, N-inhibition and S-inhibition, could be independently and selectively tailored to achieve: (a) high conversion of blue-light (without UV-light), enhanced by red-light pre-irradiation for minimal S-inhibition; and (b) efficient PC initiated by UV-light produced N-inhibition for reduced confinement thickness and for high print speed.

In Taiwan, mountainous areas account for approximately two-thirds of the total area. The steep terrain and concentrated rainfall during typhoons cause landslides, which pose a considerable threat to mountain settlements. Therefore, models for analyzing rainfall-induced landslide hazards are urgently required to ensure adequate land use in mountainous areas. In this study, focusing on Pingtung County in southern Taiwan, we developed a landslide hazard index (IRL) to land use. Using FORMOSA-2 and SPOT-5 satellite images, data were collected before and after four typhoons (one in 2009 and three in 2013). The ArcGIS random tree classifier was used for interpreting satellite images to explore surface changes and disasters, which were used to analyze slope disturbances. The product of the maximum 3-h rolling rainfall intensity and effective accumulated rainfall was used as a rainfall trigger index (IRT). Considering environmental and slope disturbance factors, an index of slope environmental strength potential (ISESP) was developed through logistic regression (LR). Landslide hazard to land use was estimated using IRT and ISESP. The average coefficient of agreement (Kappa) was approximately 0.71 (medium to high accuracy); the overall accuracy of slope environmental strength potential analysis was approximately 80.4%. At a constant ISESP, IRT increased with the increasing hazard potential of rainfall-induced landslides. Furthermore, IRT and ISESP were positively correlated with landslide occurrence. When large ISESP values occur (e.g., fragile environment and high land development intensity), small IRT values may induce landslides.

Consumption of refined foods and beverages high in sugar make the teeth susceptible to the formation of biofilm, and lead to dental caries and diseases of the oral cavity such as periodontitis and periodontal disease. The aim of the present study was to determine the ability of selected probiotics to inhibit growth and biofilm formation by the cariogenic bacterium Streptococcus mutans in vitro. We screened strains of latic acid bacteria (LAB) (n=120) from the Bioresources Collection and Research Center (BCRC), saliva of healthy adults and infant stool. The antimicrobial activity of LAB in vitro was evaluated by agar spot culture and co-culture of the S. mutans strains. We determined the effect of heating and dilution factors (2- and 4-fold) on the antagonistic activity of LAB. Antagonistic substances in the spent culture suspensions (SCS) of LAB were precipitated by extraction with ammonium sulphate and chloroform to characterise the protein and lipophilic fractions. Results of co-culturing show that the SCS of the three LAB strains (Lactobacillus pentosus 13-1, 13-4 and Lactobacillus crispatus BCRC 14618) subjected to heat treatment showed significantly high antimicrobial activity. We found that substances produced by L. pentosus 13-4 which have the potential to exhibit antimicrobial properties might be lipophilic proteins. Additionally, we infer that the mechanism of reducing biofilm formation by Lactobacillus strains is associated with sucrose-dependent cell–cell adhesion and the gtfC level of glucosyltransferases (Gtfs) in the biofilm. Native LAB strains screened in our study may be used in chewing gums and other processed foods for preventing tooth decay.

In a collaborative forecasting task, experts may have unequal authority levels. However, this has rarely been considered reasonably in the existing fuzzy collaborative forecasting methods. In addition, experts may not be willing to discriminate their authority levels. To address these issues, an auto-weighting fuzzy weighted intersection (FWI) fuzzy collaborative intelligence approach is proposed in this study. In the proposed auto-weighting FWI fuzzy collaborative intelligence approach, experts’ authority levels are automatically and reasonably assigned based on their past forecasting performances. Subsequently, the auto-weighting FWI mechanism is established to aggregate experts’ fuzzy forecasts. The theoretical properties of the auto-weighting FWI mechanism have been discussed and compared with those of the existing fuzzy aggregation operators. After applying the auto-weighting FWI fuzzy collaborative intelligence approach to a case of forecasting the yield of a DRAM product from the literature, its advantages over several existing methods were clearly illustrated.

There has been a growing awareness of the need to implement environmentally friendly operations in the hotel industry, but most studies focus on guest behaviors. Only a few studies investigate employees’ willingness to comply with hotels’ green practices. This study seeks to further the investigation from the human resource perspective. Using alumni from a tourism and hospitality programs, this study collected 233 responses. The study hypothesizes that the employees’ green ability consisting of environmental awareness, environmental knowledge, and environmental skill creates a positive impact on hotels’ green ability. The results indicate that employees contribute approximately a fifth of hotels’ ability to implement greener practices.

With the development of artificial intelligence, the ability of capturing the background characteristics of hyperspectral imagery (HSI) is improved and promising performance in hyperspectral anomaly detection (HAD) tasks is yielded. However, existing methods proposed in recent years still suffer from certain limitations: 1) constraints are lacking in the deep feature learning process in terms of the issue for absence of prior background and anomaly information. 2) hyperspectral anomaly detectors with traditional self-supervised deep learning methods fail to ensure prioritized reconstruction of the background. 3) architectures of fully connected deep network in hyperspectral anomaly detectors lead to low utilization of spatial information and destruction for original spatial relationship of hyperspectral imagery, and disregard spectral correlation between adjacent pixels. 4) hypotheses or assumptions for background and anomaly distributions restrict the performance of many hyperspectral anomaly detectors because the distributions of background land covers are usually complex and not assumable in real-world hyperspectral imagery. With the consideration of above problems, in this paper, we propose a novel fully convolutional auto-encoder based on dual clustering and latent feature adversarial consistency (FCAE-DCAC) for HAD which is carried out in a self-supervised learning-based processing. Firstly, the density-based spatial clustering of applications with noise algorithm and connected component analysis are utilized for successive spectral and spatial clustering to obtain more precise prior background and anomaly information, which facilitates the separation between background and anomaly samples during the training of our method. Subsequently, a novel fully convolutional auto-encoder (FCAE) integrated with spatial-spectral joint attention (SSJA) is proposed to enhance the utilization of spatial information and augment feature expression. In addition, a latent feature adversarial consistency network is proposed to achieve pure background reconstruction with the ability of learning actual background distribution in hyperspectral imagery. Finally, a triplet loss is introduced to enhance the separability between background and anomaly, and the reconstruction residual serves as the anomaly detection result. We evaluate the proposed method on seven groups of real-world hyperspectral datasets, and the experimental results confirmed the effectiveness and superior performance of the proposed method versus nine state-of-the-art methods.

Unmanned aerial vehicles (UAVs) are one of the most promising innovative technologies invented in recent years to promote precision agriculture and smart farming. UAVs can not only reduce labor requirements but also increase production output, reduce the use of pesticides, and protect the environment. However, previous studies on agricultural UAVs have mostly focused on technical problems such as software and hardware design. Few studies have examined users’ behaviors in the implementation process. On the basis of Orlikowski and Gash’s technological frames, this study explored the participants’ cognition and expectation of farmers, pesticide, sprayers, and agriculture officials, who are three key groups of stakeholders involved in the application of UAVs to pesticide spraying, regarding agricultural UAVs and examined how the conflicts between their cognition and expectation influenced the choice of using pesticide spraying UAVs. The conclusions of this study contributed to supplement the content and broaden the scope of application of technological frame theory and provided a crucial reference for the promotion of agricultural UAVs in practice.

Lymphoma diagnoses in the U.S. are substantial, with an estimated 89,380 new cases in 2023, necessitating innovative treatment approaches. Phase 1 clinical trials play a pivotal role in this context. We developed a binary predictive model to assess trial adherence to expected average durations, analyzing 1,089 completed Phase 1 lymphoma trials from clinicaltrials.gov. Using machine learning, the Random Forest model demonstrated high efficacy with an accuracy of 0.7248 and ROC-AUC of 0.7701 for lymphoma trials. Importantly, this model maintained an accuracy of 0.7405 when applied to lung cancer trials, showcasing its versatility. A key insight is the correlation between higher predicted probabilities and extended trial durations, offering nuanced insights beyond binary predictions. Our research contributes to enhanced clinical research planning and potential improvements in patient outcomes in oncology.

This paper proposes to combat active eavesdropping by intelligent reflecting surface (IRS) backscatter techniques. To be specific, the source (Alice) sends the confidential information to the intended user (Bob), while the eavesdropper (Willie) transmits jamming signal to interrupt the transmission for more data interception. To enhance the secrecy, an IRS is deployed and connected with Alice through fiber to transform the jamming signal into the confidential signal by employing backscatter techniques. Based on the considered model, an optimization problem is formulated to maximize signal-to-interference-plus-noise ratio (SINR) at Bob under the constraints of the transmit power at Alice, the reflection vector at the IRS and the allowable maximum SINR at Willie. To address the optimization problem, an alternate optimization algorithm is developed. The simulation results verify the achievable secrecy gain of the proposed scheme.

Owing to the advantages of cost-effectiveness, compactness, and the avoidance of complicated camera synchronization, single-camera three-dimensional (3D) digital image correlation (DIC) techniques have gained increasing attention for deformation measurement of materials and structures. In the traditional single-camera 3D-DIC system, the left and right view images can be recorded by a single camera using a diffraction grating, a bi-prism or a set of planar mirrors. To further improve the measurement accuracy of single-camera 3D-DIC, this paper introduces a single-camera four-view imaging technique by installing a pyramidal prism in front of the camera. The 3D reconstruction of the measured points before and after deformation is realized with eight governing equations induced by four views, and the strong geometric constraints of four views can help to improve the measurement accuracy. A static experiment, a rigid body translation experiment and a four-point bending experiment show that the proposed single-camera 3D-DIC method can achieve higher measurement accuracy than the dual-view single-camera 3D-DIC techniques and has advantages in reducing both random error and systematic error.

In this paper, an adaptive technology and the interconnection and damping assignment passivity-based control method are combined to solve the stabilization problem for underactuated mechanical systems with uncertainties (including matched and unmatched). Uncertainties include unknown friction coefficients and unknown terms in kinetic energy and potential energy. A novel adaptive interconnection and damping assignment passivity-based control scheme is proposed and an adaptive stabilization controller is designed to make the closed-loop system locally stable. Verification is conducted on the ball and beam system, taking into account uncertainties of friction coefficients, kinetic energy, and potential energy. The locally asymptotic stability is demonstrated using the LaSalle’s invariance principle and approximate linearization. The effectiveness of the proposed control law is verified through numerical simulations.

In wireless sensor networks (WSNs), each sensor node can estimate the global parameter from the local data in distributed manner. This paper proposed a robust diffusion estimation algorithm based on minimum error entropy criterion with self-adjusting step-size, which are referred to as diffusion MEE-SAS (DMEE-SAS) algorithm. The DMEE-SAS algorithm has fast speed of convergence and is robust against non-Gaussian noise in the measurements. The detailed performance analysis of the DMEE-SAS algorithm is performed. By combining the DMEE-SAS with diffusion minimum error entropy (DMEE) algorithms, an Improving DMEE-SAS algorithm is proposed, in non-stationary environment where tracking is very important. The Improving DMEE-SAS algorithm can avoid insensitivity of the DMEE-SAS algorithm due to the small effective step-size near the optimal estimator, and obtain a fast convergence speed. Numerical simulations are given to verify the effectiveness and advantages of these proposed algorithms.

This study has simulated the typical rainstorm on 20 July 2021 over central east China by using the first-generation Chinese Reanalysis datasets and Global Land Data Assimilation System datasets, and the Noah land surface model coupled with the advanced weather research and forecasting model. Based on this, the gridded planetary boundary layer (PBL) profiles and ensemble states within soil perturbations are collected to investigate the main land-atmosphere coupling characteristics during this modeled rainstorm by using various local coupling metrics and the introduced ensemble statistical metrics. Results have shown that (1) except for the stratospheric thermodynamics and surface thermal over mountain areas, the main characteristics of mid-low layers and surface have been well documented in this modeled rainstorm; (2) the typical coupling intensity is characterized by the dominant morning moistening, early noon weak PBL warming around 2, noontime buoyant mixing temperature deficit around 274 K, daytime PBL and surface latent flux contribution around 100 and 280 W/m2 respectively, and significant afternoon soil-surface latent flux coupling; (3) moist static energy is more significant than PBL height during the relation chains, which is consistent with the significance of surface moistening indicated by local coupling metrics. In general, wet soil contributes greatly to daytime moisture evaporation, which then increases the early noon PBL warming and enhances the noontime buoyant mixing within weak flux contribution. However, this has been suppressed by large-scale forcing such as the upper southwestern inflows of rainstorms, which has further significantly shaped the spatial distribution of statistical metrics in contrast. These quantitatively described local couplings have highlighted both the convection potential diagnoses usage for the local weather application and more applicable coupling threshold diagnoses within the finer spatial investigation.

A novel prediction model for crack development of reinforced concrete (RC) piles with localized chloride corrosion in marine environment is proposed. A discrete method is used to solve the corrosion pit radius model and a crack extension model is developed to investigate the initiation and extension of cracks. The maximum corrosion degree of reinforced concrete pile is predicted according to the limit crack criterion, and finally a sensitivity analysis is carried out on the important parameters of crack extension. The results show that the radius of corrosion pit, the depth corrosion pit and cross-sectional area loss of reinforcement gradually increase as the corrosion level increases. The loss of local reinforcement section at crack initiation decreases with the increase of the ratio of concrete cover to initial diameter, and increases with the increase of pitting factor. The required pit depth for reinforcement cracking increases with the increase of the ratio of concrete cover thickness to diameter. The loss of cross-sectional area of reinforcement and the radius of corrosion pit increase with the increase of initial diameter of reinforcement. Increasing the pitting factor will reduce the pit depth and make the crack width develop faster before reaching the limit crack width. Increasing the concrete cover thickness can provide an improvement in the propagation of cracks. A comparative analysis shows that the localized corrosion pattern is more in conformity with marine engineering practice.

Gelidium jelly was traditionally made by boiling processed Gelidium seaweed and allowing the filtrate to congeal into jelly. The processing of Gelidium seaweed was very complicate involved the repeated procedures of water washing and sun drying for 7 times, and the seaweed was originally purple-red in color turned into yellow after the repeated wash and sun drying. This study aimed to evaluate the effects of halogen lamp drying methods in replace of sun drying on the physical-chemical qualities of Gelidium jellies. Properties included the agar yield, gelling temperature, hardness, springiness, rheological parameters, sensory attributes, color, and volatile compounds were investigated. The results demonstrated halogen lamp drying method required 12 times of washing and drying processes to achieve the similar jelly properties compared to sun drying for 7 times in the experimental conditions. Volatiles including heptanal, β-ionone, and (E)-2-decenal could be used as indicators to monitor the washing and drying processing. Halogen lamp was found could be an alternative processing method for seaweed drying, especially at rainy days.

Caring for dolphins is a delicate process that requires experienced caretakers to pay close attention to their behavioral characteristics. However, caretakers may sometimes lack experience or not be able to give their full attention, which can lead to misjudgment or oversight. To address these issues, a dolphin behavior analysis system has been designed to assist caretakers in making accurate assessments. The study utilized image preprocessing techniques to reduce sunlight reflection in the pool and enhance the outline of dolphins, making it easier to analyze their movements. The dolphins were divided into 11 keypoints using an open-source tool called DeepLabCut, which helped accurately mark various body parts for skeletal detection. The AquaAI Dolphin Decoder (ADD) was then used to analyze six dolphin behaviors. To improve behavior recognition accuracy, the Long Short-Term Memory (LSTM) neural network was introduced. The ADD and LSTM models were integrated to form the ADD-LSTM system. Several classification models, including unidirectional and bidirectional LSTM, GRU, and SVM, were compared. The results showed that the ADD module combined with a double-layer bidirectional LSTM method achieved high accuracy in dolphin behavior analysis. The accuracy rates for each behavior were over 90%.

This research develops the Osteoporosis Knowledge, Attitude, and Behaviors Questionnaire (OKABQ) with the intent to evaluate levels of osteoporosis knowledge, attitude and behavior change. The aims of the study were to develop and validate the OKABQ; and to establish a mediation model of the research. A quantitative, descriptive, and instrumental study was conducted in two phases: Phase I—development of the scale through Delphi Method by osteoporosis experts; Phase II—evaluation of the validity and reliability of the scale and construction of a mediation model using SmartPLS. In Phase I, the content validity index (CVI) of the questionnaire was higher than 0.96 and the inter-rater reliability (IRR) kappa was 1.00. In Phase II, exploratory factor analysis showed that two predominating factors of attitude as a mediation were addressed by the 26-item OKABQ. The indirect effect results from the estimated model indicates that attitude mediates the relationship between knowledge and behaviors (β = 0.114, t = 2.627, p < 0.001), which is positive and statistically significant. We concluded that the OKABQ is a valid measure of osteoporosis knowledge, attitude and behaviors for women with osteoporosis. These assessment results could assist healthcare providers in mitigating insufficiency on health education.

In this paper, the synthesis of two novel luminescent Eu3+ ion complexes [Eu(TFT)3(phen) (1) and Eu(TFT)3(bpy)•Hex (2)] based on the combination of 2-(2,2,2-trifluoroethyl)-1-tetralone (TFT), containing n-donor ligands (1,10-phenanthroline or 2,2'-Bipyridine) and Eu3+ ion is reported herein, and their structural features are discussed on the basis of X-ray crystallographic and thermal analyses. We observed that the ligands transfer energy effectively to the metal center by fluorescence, IR and UV spectrograms studies. The structures and properties of complexes 1-2 were optimized by the DFT theoretical calculation, and the calculation results were consistent with the experimental X-ray structure data and spectral analysis.

By using various skill scores and spatial characteristics of spatial verification methods and tradi-tional techniques of the model evaluation tool (MET, V10.0.0), the gridded precipitation obser-vation CMPAV (V2.0) and three datasets that derived from local (LOC), Shanghai (SHA), and Grapes (GRA) model respectively are conducted to assess the 3 lead day rainfall forecast with 0.5-day intervals during summer of 2020 over central east China. Results have shown that LOC generally outperforms the other two for most skill scores but usually with relatively larger un-certainties than SHA, and it has the least displacement errors for moderate rainfall among the three datasets. However, the rainfall of GRA has been heavily underestimated and accompanied with large displacement error. Both LOC and SHA have shown almost equitable abilities in forecasting convection and rainstorms of the large area but with a slightly over-forecast of local convection, while LOC likely over-forecasts the local rainstorms. In addition, SHA slightly favors over-forecast on a broad scale range and a broad threshold range, and LOC slightly misses the rainfall exceeding 100 mm. Generally, for a broadly comparative evaluation on rainfall, the popular dichotomous methods should be recommended under considering reasonable classifi-cation of thresholds if the accuracy is highly demanded. And most spatial methods should be suggested to conduct with proper pre-handling of non-rainfall event cases. Especially, the veri-fications including spatial characteristic difference information could be recommended in a computationally sufficient environment.

A conventional 2D numerical model is improved by incorporating three submodels to consider different effects of secondary flow and a module for cohesive sediment transport. The model is applied to a meandering reach of Yangtze River to investigate secondary flow effects on cohesive sediment deposition, and a preferable submodel is selected based on the flow simulation results. Sediment simulation results indicate that the improved model predictions are in better agreement with the measurements in planar distribution of deposition as the increased sediment deposits caused by secondary current on the convex bank have been well predicted. Secondary flow effects on predicted amount of deposition become more obvious during the period when the sediment load is low and velocity redistribution induced by the bed topography is evident. Such effects vary with the settling velocity and critical shear stress for deposition of cohesive sediment. The bed topography effects can be reflected by the secondary flow submodels.

In recent decades, as eutrophication in inland and coastal waters (ICWs) has increased due to anthropogenic activities and global warming, so has the need for timely monitoring. Compared with traditional sampling and laboratory analysis methods, satellite remote sensing technology can provide macro-scale, low-cost, and near real-time water quality monitoring services. The Geostationary Ocean Color Imager (GOCI), integrated onboard the Communication Ocean and Meteorological Satellite (COMS) from the Republic of Korea, was the first geostationary ocean color observation satellite and was operational from April 1, 2011 to March 31, 2021. Over ten years, GOCI has observed oceans, coastal waters, and inland waters within its 2,500 km×2,500 km target area centered on the Korean Peninsula. The most attractive feature of GOCI, compared with other commonly used watercolor sensors, was its high temporal resolution (1h, eight times daily from 0 UTC to 7 UTC), providing the opportunity to monitor the quality of ICWs, where optical properties can change rapidly throughout the day. This systematic review aims to comprehensively review GOCI features and applications in ICWs, analyzing progress in atmospheric correction algorithms and water quality monitoring. Analyzing 123 articles from the Web of Science and China National Knowledge Infrastructure (CNKI) through a bibliometric quantitative approach, we examined GOCI’s strength and performance with different processing methods. These articles reveal that GOCI played an essential role in monitoring the ecological health of ICWs in its observation area in East Asia. GOCI has led the way to a new era of geostationary ocean satellites, providing new technical means for monitoring water quality in oceans, coastal zones, and inland lakes. We also discuss the challenges encountered by geostationary satellites in monitoring water quality and provide suggestions for improvements.

This paper reviews several techniques, including analytical theories and real frequency techniques, to design ultra-wideband impedance matching networks for low-power applications. The comparison of solutions obtained using the simplified real frequency technique to the published solution using Chebyshev filter theory is demonstrated.

The proper regulation of RNA processing is critical for muscle development and the fine-tuning of contractile ability between muscle fiber-types. RNA binding proteins (RBPs) regulate the diverse steps in RNA processing including alternative splicing, which generates fiber-type specific isoforms of structural proteins that confer contractile sarcomeres with distinct biomechanical properties. Alternative splicing is disrupted in muscle diseases such as myotonic dystrophy and dilated cardiomyopathy, and is altered after intense exercise as well as with aging. It is therefore important to understand splicing and RBP function, but currently only a small fraction of the hundreds of annotated RBPs expressed in muscle have been characterized. Here we demonstrate the utility of Drosophila as a genetic model system to investigate basic developmental mechanisms of RBP function in myogenesis. We find that RBPs exhibit dynamic temporal and fiber-type specific expression patterns in mRNA-Seq data and display muscle-specific phenotypes. We performed knockdown with 105 RNAi hairpins targeting 35 RBPs and report associated lethality, flight, myofiber and sarcomere defects, including flight muscle phenotypes for Doa, Rm62, mub, mbl, sbr, and clu. Interestingly, knockdown phenotypes of spliceosome components, as highlighted by phenotypes for A-complex components SF1 and Hrb87F (hnRNPA1), revealed level- and temporal-dependent myofibril defects. We further show that splicing mediated by SF1 and Hrb87F is necessary for Z-disc stability and proper myofibril development, and strong knockdown of either gene results in impaired localization of Kettin to the Z-disc. Our results expand the number of RBPs with a described phenotype in muscle and underscore the diversity in myofibril and transcriptomic phenotypes associated with splicing defects. Drosophila is thus a useful model to gain disease-relevant insight into cellular and molecular phenotypes observed when expression levels of splicing factors, spliceosome components and splicing dynamics are altered.

In this study, a simple, easy and convenient fluorescent sensing system for detection of vascular endothelial growth factor (VEGF) based on VEGF aptamers, aptamer-complementary fluorescence-labeled probe and streptavidin magnetic beads was developed in only one single tube. The VEGF is the most important biomarker in cancer angiogenesis, and is investigated that serum VEGF level was various according to the different type and course of cancers. Hence, efficient quantification of VEGF is able to improve the accuracy of cancer diagnosis and precision of disease surveillance. In this research, the VEGF aptamer was designed to be able to bind with the VEGF by forming G-quadruplex secondary structures, and then the magnetic beads would capture the none-binding aptamers due to none steric interference, and finally, the fluorescence-labeled probes were hybridized with the aptamers captured by the magnetic beads. Therefore, the fluorescent intensity in the supernatant would specifically reflect the present of VEGF. After an overall optimization, the optimal conditions for detection of VEGF were as followed, KCl, 50 μM; pH 7.0; aptamer, 0.1 μM and magnetic beads, 10 μL (4 μg/μL). The VEGF could be well quantified within a range of 0.2-2.0 ng/ml in plasma, and the calibration curve possessed a good linearity (y = 1.0391x + 0.5471, r = 0.998). The detection limit (LOD) was calculated to be 0.0445 ng/mL according to the formula (LOD = 3.3×σ/S). The specificity of this method was also investigated under the appearance of many other serum proteins, and the data showed the good specificity in this aptasensor-based magnetic sensing system. This strategy provided a simple, sensitive and selective biosensing platform for detection of serum VEGF. Finally, it was expected that this detection technique can be promoted to more clinical applications.

To date, viral RNA detection is almost the only way to confirm SARS-CoV-2infectionin practice.However, variousreasons can cause low sensitivity for RNA detection, and thisposes aserious challenge to disease control. We tested the performance of detecting total antibody(Ab) and IgM levels in serum by the methods of chemiluminescence, enzyme-linked immunosorbent assay (ELISA), and colloidal golddetection. The datashowed that the sensitivity and specificity for detecting total Ab and IgM levels were high by all three methods, and the sensitivity was higher for detecting total Ab than for detecting IgM. Evidence from studieshas shown thatviral RNA testingcombinedwith serological testing could increase the diagnostic sensitivity while maintaining a high specificity. Specific serology testsfor SARS-CoV-2 havegreat value for clinical practice and public health.

Embryo stage of oxidation of an epi Ge(001)-2×1 by atomic oxygen and molecular O₂ is studied via synchrotron radiation photoemission. The topmost surface buckled with the up- and down-dimer atoms and the first subsurface layer behave distinctly from the bulk by exhibiting surface core-level shifts in the Ge 3d core-level spectrum. The O₂ molecules become dissociated upon reaching the epi Ge(001)-2×1 surface. One of the O atom removes off the up-dimer atom, and the other bonds with the underneath Ge atom in the subsurface layer. Atomic oxygen adsorbed on the epi Ge(001)-2×1 preferentially in between the up-dimer atoms and the underneath subsurface atoms without affecting the down-dimer atoms. The electronic environment of the O-affiliated Ge up-dimer atoms becomes similar to that of the down-dimer atoms. Both exhibit an enrichment in charge, where the subsurface of the Ge layer is maintained in a charge-deficient state. The dipole moment originally generated in the buckled reconstruction no longer exists, thereby resulting in a decrease in the ionization potential. The down-dimer Ge atoms and the back-bonded subsurface atoms remain inert to atomic O and molecular O₂, a possible cause of low reliability in Ge-related metal-oxide-semiconductor (MOS) devices.

Age-related sarcopenia meaningfully increases the risks of functional limitations and mortality in the elderly. Although circulating microRNAs (c-miRNAs) are associated with aging-related cellular senescence and inflammation, the relationships between c-miRNAs and sarcopenia in the elderly remain unclear. This study investigates whether circulating myo-miRNAs and inflammation-related miRNAs are associated with sarcopenia in the elderly. This study recruited 77 eligible subjects (41 males and 36 females) from 597 community-dwelling older adults, and then divided into normal (n=24), dynapenic (loss of muscular function without mass, n=35), and sarcopenic groups (loss of muscular function with mass, n=18). Moreover, myo-miRNAs (c-miRNA-133a and c-miRNA-486), inflammation-related miRNAs (c-miRNA-21 and c-miRNA-146a), and inflammatory-related cytokine levels in plasma were determined using quantitative polymerase chain reaction and ELISA, respectively. The results demonstrated that sarcopenic group exhibited lesser skeletal muscle mass index (SMI), handgrip strength, and gait speed, as well as, lower c-miR-486 and c-miR-146a levels, compared to those of normal and dynapenic groups. Moreover, c-miR-486 level was positively related to SMI (r=0.334, P=0.003), whereas c-miR-146a level was positively associated with SMI (r=0.240, P=0.035) and handgrip strength (r=0.253, P=0.027). In the receiver operating characteristic analysis for predicting sarcopenia, the area under the curve in c-miR-486 was 0.708 (95% confidence interval: 0.561-0.855, P=0.008) and c-miR-146a was 0.676 (95% CI: 0.551-0.801, P=0.024). However, no significant relationships were observed between SMI/ handgrip strength/gait speed and plasma myeloperoxidase/interleukin-1?/interleukin-6 levels. In conclusion, myo-miRNA (c-miR-486) and inflammation-related miRNA (c-miR-146a) are superior to inflammatory peroxide/cytokines in plasma for serving as critical biomarkers of age-related sarcopenia.