Both fibrosis and cirrhosis of the liver are the end results of most kinds of chronic liver damage and present a common but difficult clinical challenge throughout the world. The inhibition of the fibrogenic, proliferative, and migratory effects of hepatic stellate cells (HSCs) has become an experimental therapy for preventing and even reversing hepatic fibrosis. Furthermore, a complete understanding of the function of non-coding RNA-mediated epigenetic mechanisms in HSC activation may improve our perception of liver fibrosis pathogenesis. This review focuses on an evolving view of molecular mechanisms in which HSC activation by miR-29a signaling may moderate their profibrogenic phenotype, thus supporting the use of miR-29a agonists as a potential therapy for treating liver fibrosis in the future.

With permafrost degenerating caused by climate change, water accumulation increases in permafrost regions during last decades. Water accumulation will deteriorate existing status of engineering in cold regions. Water accumulation can make a thermal effect on permafrost under construction, even result in failure of the subgrade. Moreover, the thermal effect is related to water temperature. However, temperature variation of water accumulation is complex, and its influence factors include air temperature, environment, scope of water accumulation and so on. In order to make analysis of the damage mechanism of water accumulation on permafrost, it is necessary to explore the internal temperature change of water accumulation. This paper proposes a review about temperature calculation method of water accumulation in cold environment. The thermal calculation method between air and water boundary of water accumulation is summarized. Water temperature change of water accumulation with various type is analyzed. The thermal calculation considering phase transformation in water accumulation is discussed, and heat transfer from the bottom of water accumulation to the underlying soil is further studied. Finally, the key factors which are advantageous to make research about the thermal effect of water accumulation in permafrost is proposed to optimize calculation method.

The investigation aims to analyze the effect of homogenization heat treatment on the quantity, distribution, morphology, and chemical composition of δ ferrite and sigma phase in the 316L austenitic stainless steel cast billet. Microstructures of the cast billet at different locations, center, 0.5 R, R, and the subsequent 2/6-hour homogenization heat treatment at 1240 oC were examined. The microstructure at the radius R was much more uniform and expected a better performance in the following hot/cold forging processes due to the highest cooling rate compared with those at 0.5R and center. The δ ferrite often accompanies the generation of the sigma phase, and the transformation of δ ferrite into the sigma/(austenite) and retained δ ferrite is strongly related to the cooling rate after homogenization heat treatment. The sigma phase is hard and detrimental to the subsequent hot/cold forgings. It must be removed from the homogenization heat treatment before forging. Fast air cooling from 850 oC to room temperature after homogenization heat treatment cannot prohibit the sigma phase formation. Rapid cooling between 850 and 1240 oC after homogenization treatment is required to avoid the sigma phase formation in the 316L stainless steel cast billet.

The basic oxygen furnace slag (BOF) was wide used in road construction, but there was a lack of characteristics in different asphalt mixtures. This study investigates the properties of hot-mixed asphalt (HMA) containing stone mastic asphalt (SMA), porous asphalt (PA) and dense-graded BOF as a partial substitution for natural aggregates. The purpose of this study is to evaluate various BOF slag contents in the asphalt mixtures would affect the cooling behavior after compaction. Asphalt mixture specimens contained 0%, 20%, 40% and 60% BOF slag, respectively, as coarse aggregate. Test results showed that BOF slag has a lipophilic property, so it can be adsorbed by asphalt cement, thereby reducing the cost of asphalt. The stability value of all asphalt mixtures increases with the proportion of BOF slag replacement. In addition, the voids in the mineral aggregate (VMA) value variable exhibited significant differences among asphalt mixtures, and could determine the deviation of the cooling trend of asphalt mixtures. Furthermore; it was found that the cooling procedure of the BOF slag used in dense-graded asphalt mixture takes about 100 min, and that the temperature tends to be moderate; however, it took about 120 min of cooling the SMA and PA mixture with BOF slag. In addition, the voids distribution of dense asphalt mixture was not uniform. It would result in various locations of thermal energy temperature on asphalt mixtures that were inconsistent.

Fibromyalgia (FM) is a complex, chronic, widespread pain syndrome that can cause significant health and economic burden. Emerging evidence has shown that neuroinflammation is an underlying pathological mechanism in fibromyalgia. Toll-like receptors (TLRs) are key mediators of the immune system. TLR4 is expressed primarily in microglia and regulates downstream signaling pathways, such as MyD88/NF-κB and TRIF/IRF3. It remains unknown whether electroacupuncture (EA) has therapeutic benefit in attenuating fibromyalgia pain and what role the TLR4 pathway may play in this effect. We compared EA with sham EA to eliminate the placebo effect due to acupuncture. We demonstrated that intermittent cold stress significantly induced an increase in mechanical and thermal FM pain in mice (mechanical: 2.48 ± 0.53 g; thermal: 5.64 ± 0.32 s). EA but not sham EA has analgesic effect on FM mice. TLR4 and inflammatory mediators-related molecules were increased in FM mice’s thalamus, medial prefrontal cortex, somatosensory cortex, and amygdala, indicating neuroinflammation and microglial activation. These molecules were reduced by EA but not sham EA. Furthermore, a new chemogenetics method was used to precisely inhibit SSC activity displayed an anti-nociceptive effect through TLR4 pathway. Our results imply that the analgesic effect of EA is associated with TLR4 downregulation. We provide novel evidence that EA can modulate the TLR4 signaling pathway, revealing potential therapeutic targets for FM pain.

Food waste is a common issue arising from grinding of food by experimental animals, leading to excessive food scraps falling into cages. In the wild, animals grind food by gnawing vegetation and seeds, potentially damaging the ecological environment. However, limited ecology studies have focused on food grinding behavior since the last century, with even fewer on rodent food grinding, particularly recently. Although food grinding function is partially understood, biological purposes remain under-investigated and driving factors unclear. This review aims to explain potential causes of animal food grinding, identify influencing factors, and discuss contexts and limitations. Specifically, we emphasize recent progress on gut microbiota significance for food grinding. Moreover, we show abnormal food grinding is determined by degree of excess normal behavior, emphasizing food grinding is not meaningless. Findings from this review promote comprehensive research on the myriad factors, multifaceted roles, and intricate evolution underlying food grinding behavior, benefiting laboratory animal husbandry and ecological environment protection, and identifying potential physiological benefits yet undiscovered.

In the first part of this talk we review some prerequisites for and essential arguments involved in the construction of the thermal-ground-state estimate for the deconfining phase in the thermodynamics of SU(2) Quantum Yang-Mills theory and how this structure supports its distinct excitations. The second part applies deconfining SU(2) Yang-Mills thermodynamics to the Cosmic Microwave Background in view of (i) a modified temperature-redshift relation with an interesting link to correlation-length criticality in the 3D Ising model, (ii) the implied minimal changes in the dark sector of the cosmological model, and (iii) best-fit parameter values of this model when confronted with the spectra of the angular two-point functions TT, TE, and EE, excluding the low-$l$ physics. The latter, which is treated in an incomplete way because of the omission of radiative effects, is addressed in passing towards future work.

On 17 October 1947, Niels Bohr was made a knight of the Order of the Elephant by the King of Denmark in view of his outstanding achievements and contributions to science. Bohr designed his own coat of arms that featured a pattern of Yin and Yang (Tai Chi symbol) to symbolize the wave-particle complementarity. However, Bohr’s Yin-Yang diagram (YYD) was neither drawn based on the principles of quantum mechanics, nor did it originate from the traditional Taoist YYD. Scientists still have doubts about the legitimacy of using YYD as the icon of the wave-particle complementarity, because the YYD belonging to quantum mechanics itself is unknown so far. This article reports the YYDs existing in quantum mechanics and justifies the role of YYD in the wave-particle duality by showing that any system, whether classical or quantum, has an ideal YYD as long as it satisfies Bohr’s principle of complementarity (BPC). The deviation of a deformed YYD from the ideal YYD indicates the extent to which a real system satisfies BPC. This article constructs the quantum YYD by the complex quantum trajectory of a particle tunneling via a step barrier, which displays the continuous transition between the wave behavior and the particle behavior. It appears that the YYD designed by Bohr in his coat of arms resembles the YYD generated by tunneling motion, not only in appearance but also in the governing equation.

We present set-theoretical solutions of the Yang-Baxter equation in BCK–algebras. Some solutions in BCK−algebras are not solutions in other structures (such as MV −algebras). Related to our investigations we also consider some new structures: Boolean coalgebras and a unified braid condition – quantum Yang-Baxter equation. Finally, we will see how poetry has accompanied the development / history of the Yang–Baxter equation.

EGFR mutations are heterogenous but all carry the same weighting in the Lung-molGPA. The aim of this study was to elucidate the different prognostic implications of molecular subtypes and frontline TKIs in EGFR-mutated lung adenocarcinoma with synchronous brain metastases (BM) using the Lung-molGPA. Medical records were searched in hospital databases from 2011 to 2015. Patients with EGFR-mutated adenocarcinoma and brain metastases who received TKIs were included. The Kaplan-Meier method was used to estimate survival, and multivariate Cox proportional hazard models were used to estimate adjusted hazard ratios (HRs) and 95% confidence intervals (CIs). A total of 256 patients were included with a median overall survival (OS) of 17.2 months. In multivariate analysis of OS, only age (70 versus <70 years, HR:1.71, 95% CI:1.25-2.35, p<0.001), KPS (<70 versus 70, HR:1.71, 95% CI:1.26-2.31, p<0.001), and rare mutations (other versus exon 19 deletions, HR:1.78, 95% CI:1.04-3.05, p=0.037) remained statistically significant. In patients with a Lung-molGPA score 2.5, EGFR molecular subtypes had different median OS (exon 19 deletions versus Leu858Arg versus other, 18.8 vs 12.4 vs 12.1 months, p=0.021). In conclusion, different molecular subtypes treated with frontline TKIs have different prognostic implications in the Lung-molGPA. Further prospective studies are warranted to validate these findings.

Novel 1,2,3-triazole compounds 3–4 were synthesised via the regioselective addition and cyclization reaction of 1,1-enediamines (EDAMs) 1 with p-methylbenzenesulfonyl azide (TsN₃) 2 in 1,4-dioxane at refluxing for 5 hours. As a result, 1,2,3-triazoles 3–4 can be easily and efficiently obtained via catalyst-free click chemistry. The reactions have some advantages such as metal-free catalyst, excellent yield, inexpensive raw materials, and convenient final treatment.

Patients with end stage liver disease (ESLD) undergoing liver transplantation are prone to thromboses both while on the waiting list or in the perioperative period. This hypercoagulability is associated with significant endothelial dysfunction (ED) due to nitric oxide dysregulation. ED in combination with increased thrombin generation are the main factors responsible for this hypercoagulability. Sepsis itself can significantly change the coagulation profile, but in combination with ESLD, sepsis, and septic shock is responsible for very complex changes in the patients coagulation making both assessment and management of coagulation in patients with ESLD very challenging. Viscoelastic testing (VET) is a preferred method of coagulation management in patients with cirrhosis because, as with standard laboratory testing, VET can assess the entire coagulation system including the interaction between both pro- and anticoagulants and platelets.

The rank-3 antisymmetric tensors which are the magnetic monopoles of SU(N) Yang-Mills gauge theory dynamics, unlike their counterparts in Maxwell’s U(1) electrodynamics, are non-vanishing, and do permit a net flux of Yang-Mills analogs to the magnetic field through closed spatial surfaces. When electric source currents of the same Yang-Mills dynamics are inverted and their fermions inserted into these Yang-Mills monopoles to create a system, this system in its unperturbed state contains exactly 3 fermions due to the monopole rank-3 and its 3 additive field strength gradient terms in covariant form. So to ensure that every fermion in this system occupies an exclusive quantum state, the Exclusion Principle is used to place each of the 3 fermions into the fundamental representation of the simple gauge group with an SU(3) symmetry. After the symmetry of the monopole is broken to make this system indivisible, the gauge bosons inside the monopole become massless, the SU(3) color symmetry of the fermions becomes exact, and a propagator is established for each fermion. The monopoles then have the same antisymmetric color singlet wavefunction as a baryon, and the field quanta of the magnetic fields fluxing through the monopole surface have the same symmetric color singlet wavefunction as a meson. Consequently, we are able to identify these fermions with colored quarks, the gauge bosons with gluons, the magnetic monopoles with baryons, and the fluxing entities with mesons, while establishing that the quarks and gluons remain confined and identifying the symmetry breaking with hadronization. Analytic tools developed along the way are then used to fill the Yang-Mills mass gap.

Recently, the awareness of energy conservation, carbon emission reduction, and environmental protection in Taiwan has begun to gradually improve, and bicycles have become an important vehicle for residents. In 2009, Kaohsiung began promoting public bicycle sharing. The number of users in that year amounted to 140,000. By 2015, the accumulated number of users reached nine million. This study adopted the Theory of Planned Behavior (TPB) to explore the factors influencing the behavioral intentions of public bicycle users, including the three dimensions of attitude, subjective norm, and perceived behavioral control, and probed into the relationship between the factors influencing the behavioral intentions of public bicycle users in Kaohsiung City and the dimensions. This study used a questionnaire to collect data and SPSS & AMOS for statistical analysis. The empirical results demonstrated that the most prominent factors influencing the behavioral intentions of public bicycle users in Kaohsiung City included perceived behavioral control, attitude, and subjective norm, in order. Among the influencing factors in the three dimensions, personal interests, main groups, and self-competence had a positive and significant correlation. Administrators should provide more incentives related to the three influencing factors to encourage the public in Kaohsiung City to use public bicycles more frequently as their short-distance travel mode, so as to achieve the purposes of saving energy, reducing carbon emissions, and protecting the urban environment.

To obtain a better estimation frequency band for source bearing estimation, source bearing estimation experiments using an ice-mounted geophone were performed at three sites on the Arctic ice cap. By transforming to the frequency domain, errors of the bearing estimation in a number of frequency bands within 1000 Hz and the horizontal peak displacements received by the geophone in the corresponding frequency bands were obtained. After comparing the variation of errors to the peak displacements in the same frequency band, it is found that the errors are related to the peak displacements, and higher peak displacement values mean smaller errors. When the incident angle of the acoustic source and the ice thickness meet certain conditions, some modes of the Lamb waves of the ice plate are excited, the peak displacements at the same frequency band are increased, the errors of bearing estimation are reduced, and the effective frequency band for bearing estimation is broadened. These results provide some new ideas for the bearing estimation of acoustic sources beneath Arctic ice.

In the mold machining process, the cutting tool is worn with machining time, thereby affecting the surface accuracy, leading to poor workpiece dimensions, even fracture. At present, many studies have used multiple sensors to detect the machining conditions of cutting tool and workpiece, including indirect measurement method and direct measurement method. The indirect measurement method, which has been studied widely, mainly uses sensors to capture signals for subsequent data analysis; the direct measurement method mainly analyzes the state of cutting shear zone. Due to the cut-in of cutting tool in the machining process, the workpiece is dislocated rapidly, generating considerable amount of heat, which is transferred to the chips, inducing color change on the surface of chips. Many engineers with machining experience often judge the machining state and tool life according to the chips. The engineers' experience is digitized in this study, and indirect measuring sensors are used to predict the tool life, so as to attain the objective for smart manufacturing, the average percentage error of MAPE using single vibration and voltage eigenvalues as input features is 10%, the voltage signal characteristic values and vibration signal characteristic values are combined. Finally, the chip surface chromaticity eigenvalue is combined with signal characteristic value. The average prediction error of BP-LM method is 7.85%, the average prediction error of GRNN method is 6.59%. Therefore, when the eigenvalue of chip surface chromaticity is added to the prediction result, it can enhance the accuracy of cutting tool wear value prediction more effectively than single sensor signal characteristic value.

To achieve n-type doping in diamond, extensive investigations employing first principles have been conducted on various models of phosphorus doping and boron-phosphorus co-doping. The primary focus of this study is to comprehensively analyze the formation energy, band structure, density of states, and ionization energy of these structures. It is observed that within a diamond structure solely composed of phosphorus atoms, the formation energy of an individual carbon atom is excessively high. However, the substitution of two carbon atoms leads to the conversion of diamond into a p-type semiconductor. Upon examining the P-B co-doping structure, it is revealed that the doped impurities exhibit a tendency to form more stable cluster configurations. As the separation between the freely doped atoms and the cluster impurity structure increases, the overall stability of the structure diminishes, consequently resulting in an elevation of the ionization energy. Analysis of the electronic density of states demonstrates that the electron orbit of the B atom makes negligible contributions to the impurity levels during P-B doping.

Xinjiang, as a climate-sensitive region in northwest China, holds significant importance in studying extreme weather events for agricultural production and socioeconomic development. Based on data from 52 meteorological stations and 23 extreme climate indicators in Xinjiang from 1960 to 2021, the 5a moving average, linear trend estimation, climate tendency rate, and GIS spatial analysis methods are used to analyze the distribution and change characteristics of extreme climate. The results revealed that from 1960 to 2021, TXx, TNx, TXn, TNn, FD, ID, TN10p, TX10p, and WSDI showed a significant upward trend, while SU, TR, TN90p, TX90p, and CSDI showed a significant downward trend. What is more, the range of changes in the extreme temperature indexes from 1990 to 2021 is higher than that of 1960 to 1989. The high-value areas of extreme indexes are primarily concentrated in the northern part, while the high-value areas of cold event indexes are mainly distributed in the southern part. The upward/downward trends all accounting for over 80.00% of the entire region. The Rx1day, Rx5day, PRCPTOT, R95p, R99p, R10, R20, and R25 showed a significant growth trend from 1960 to 2021, and the range of change in the extreme precipitation indexes from 1990 to 2021 was lower than that from 1960 to 1989. Moreover, their high-value areas and high climate tendency areas are mainly concentrated in the northern and western parts of Xinjiang, with upward trends all accounting for over 71.00% of the entire region. The research results provide theoretical foundations for formulating climate risk strategies in the northwest region of China.

This paper first explains the theory of the origin of force from a new perspective, explaining that the origin of all forces is caused by the "missing of energy in the time dimension" (non-conservation in a certain period of time), and constructs a unified theory of force on this basis. Then, through the unified theory of force, the following phenomena are reinterpreted: (1) The common origin of the inverse square law of gravitation and electromagnetic force; (2) The origin of the repulsive force of electrons and protons at small distances; (3) The mystery of the rotation curve of galaxies and the new explanation of "dark matter"; (4) explain the origin of the magnetic field; (5) Predict that moving magnets have the same radiation effect as charged particles (electron magnetic moments also have radiation effects); (6) Reinterpret Maxwell's displacement current; (7) Reinterpret synchrotron radiation and bremsstrahlung; (8) Explain that the strong and weak forces are short-range forces; (9) Predict the true structure of black holes and the origin of gravitational waves;(10) Possible explanation for the origin of the speed of light.

In Functional Analysis as well as Topology, we frequently encounter sets, say $X$, that contain elements close to each other. These sets display a defining "finite-ness" property: for all open cover $\mathcal{O}$ of $X$, there exists a finite subcollection $\mathcal{U}\subseteq\mathcal{O}$ such that $\mathcal{U}$ covers $X$. Such spaces $X$ are called $\textbf{compact}$, and the above "finite-ness" property afford us great convenience, because we can always investigate $X$ by investigating its finite open cover $\mathcal{U}$Arzela-

Translational rockslides caused by toe excavation are one of the commonly seen geohazards in mountainous regions due to line traffic construction. Quantifying their failure extension length (FEL) and travel distance are of significant interest as well as huge challenges in landslide hazard assessment. In this paper, a simple criterion is proposed for predicting these two factors based on the principles of rigid body limit equilibrium and kinetic energy theorem. Further, the proposed criterion is validated against the field observations and numerical results with a practical case of the Xinjianan landslide, a medium-sized translational rockslide that occurred in 2013 in Nanchuan District, Chongqing. The findings indicate that a tiny discrepancy can be found in FEL between the field observations and the proposed criteria, while this discrepancy could be considerable in travel distance between different methods. However, the relative discrepancies all fall within 20%, deemed acceptable.

COVID-19 is a highly infectious respiratory illness caused by SARS-CoV-2, and acute lung injury (ALI) is the major cause of COVID-19. The challenge in studying SARS-CoV-2 pathogenicity is the limited availability of animal models. Therefore, it is necessary to establish animal models that can reproduce multiple characteristics of ALI to study therapeutic applications. The present study established a mouse model that has features of ALI that are similar to COVID-19 syndrome to investigate the role of ACE2 and the administration of the Chinese herbal prescription NRICM101 in ALI. Mice with genetic modifications, including overexpression of human ACE2 (K18-hACE2 TG) and absence of ACE2 (mACE2 KO), were intratracheally instillated with hydrochloric acid. The acid intratracheal instillation induced severe immune cell infiltration, cytokine storms, and pulmonary disease in mice. Compared with K18-hACE2 TG mice, mACE2 KO mice exhibited dramatically increased levels of multiple inflammatory cytokines (IL-6, TNF-α, and TGF-β1) in bronchoalveolar lavage fluid, histological evidence of lung injury, and dysregulation of MAPK and MMP activation. In mACE2 KO mice, NRICM101 could ameliorate the disease progression of acid-induced ALI. In conclusion, the established mouse model provided an effective platform for researchers to investigate pathological mechanisms and develop therapeutic strategies for ALI, including COVID-19-related ALI.

This paper is another applied article based on the author's "Unified Theory of Force". The main work of this paper is as follows: (1) Reinterpretation of the Lorentz contraction effect and rigorous proof that the Lorentz contraction is a physical phenomenon based on the conservation of energy and momentum under non-completely symmetrical relative motion effects. This paper proves that the Lorentz contraction effect not only occurs in the direction of motion but also simultaneously in any direction. (2) For the first time, we attempted to explain the physical meaning of the Planck energy formula in theory and associate the Planck energy formula with the Lorentz contraction effect, which can help us to have a deeper understanding of the true physical meaning behind the Planck energy formula. At the same time, we also made reasonable theoretical predictions about the basic structure of photons.

There is currently no unified explanation for the origin of Earth's magnetic field, planetary magnetic fields, stellar magnetic fields, and neutron star magnetic fields, and most importantly, none of these theories have been experimentally verified. This paper is based on a new unified theory of mechanics and its derived applications, which may provide a better explanation for the origin of magnetic fields in celestial bodies and can be experimentally tested to better answer the observed phenomena: (1) the greater the mass of the celestial body, the stronger the magnetic field; (2) the faster the rotation speed of the celestial body, the stronger the magnetic field; (3) the higher the density of the celestial body, the stronger the magnetic field produced.

This paper is mainly based on a stricter premise of the twin paradox and the assumption of inertial frame, discusses the properties of time and space under the premise of complete symmetry, and draws an interesting conclusion: the simultaneity of different reference frames is possible realized, and the space is relatively independent. And based on this, the twin paradox, cosmic inflation, ultra-distance action of quantum entanglement, microscopic space motion of particles, measurement problems and other phenomena are tentatively explained from a new angle. This interpretation is exploratory and new. At the same time, the author also proposes an experimental way to test the relative independence of space.At the same time, this paper attempts to strictly prove that Einstein's definition of simultaneity and spatial absoluteness in special relativity may be problematic.

In 2020 the world experienced the threat of the COVID-19 epidemic, as seniors and chronic disease patients typically try to reduce their exercise and social activities to avoid increasing the risk of infection, which could lead to increased loneliness and even many diseases. This research combining golf croquet games with AIoT companion robots constructs a home-based intelligent exercise system thus uses the Technology Acceptance Model (TAM), deduces users’ intention to use this system based on perceived usefulness and perceived ease of use, and adds the needs of love and belonging, esteem, cognitive, aesthetic, and self-actualization in Maslow’s needs theory to conduct system needs analysis. The analysis results show that participants have a high level of acceptance of this system, believing that it is easy to learn and operate, can increase interaction with others, also found that this system can improve self-confirmation, satisfying the third for knowledge, feeling happy, and self-actualization needs are easier to fulfill. In the future, we shall collect and record the seniors in the process of use, so as to find out their health problems as soon as possible, expand their daily life through this exercise, and achieve the goal of happy living and health care.

This study investigates the effects of Zinc (4wt.%) and severe plastic deformation on the mechanical properties of AZ61 magnesium alloy through the stir-casting process. The severe plastic deformation (equal channel angular pressing (ECAP)) has been done followed by T4 heat treatment. The microstructural examinations revealed that the addition of 4wt.%Zn enhances the uniform distribution of β-phase, contributing to a more uniformly corroded surface in corrosive environments. Additionally, dynamic recrystallization (DRX) significantly reduces the grain size of as-cast alloys after undergoing ECAP. The attained mechanical properties demonstrate that after a single ECAP pass, AZ61 + 4wt.%Zn alloy exhibits optimal yield strength (YS), ultimate compression strength (UCS), and hardness. This research highlights the promising potential of AZ61 + 4wt.%Zn alloy for enhanced mechanical and corrosion-resistant properties, offering valuable insights for applications in diverse engineering fields.

Calculus, as a starting point to everyone's study of mathematics, was developed along with classical mechanics. Though not rigorously formulated, the intuition for differential form and infinitesimal motion makes calculus not hard to understand. And hence it does not require great effort to grasp the principles of classical mechanics. However, the situation becomes quite different when it comes to the quantum world. Given a particle system, what of interest is always the physical quantity of this system, such as energy, position, momentum, entropy, etc. But it is no longer straightforward.

In-situ observation on the austenite grain growth and martensite transformation in a developed NM500 wear-resistant steel were conducted on a Confocal Laser Scanning High-temperature Microscope (CSLM). Results indicated that the martensite nucleation did not synchronously proceed during quenching process. The selective prenucleation dominated in martensite nucleation, which dividing untransformed austenite into several regions, and resulting in the larger size of fresh martensite. Martensite can not only nucleate at parent austenite grain boundaries, but also nucleate in the preformed martensite laths and twins. Smaller constraint in the martensite growth was achieved in a larger parent austenite grain size, leading to the longer fresh martensite and secondary martensite. Besides, the transformation kinetics of martensite was accelerated in a higher quenching temperature. Moreover, the martensitic laths presented in parallel laths (0~2°) based on the pre-formed lath or distributed in triangle, parallelogram or hexagon with an angle of 60° or 120°. Interestingly, martensitic lath also traversed the unstable new parent austenitic grain boundaries. In addition, the size of austenite grains increased with the quenching temperature, and austenite grains coarsened in a short time at a higher quenching temperature of 1160 ℃. Furthermore, a large amount fine dispersed particles redissolved and ripped at 1160 ℃, resulting in the many large and visible carbonitrides.

This study investigates the impact of fintech, particularly blockchain technology and non-fungible tokens (NFTs), on the art market. As fintech has been widely accepted, the art market has undergone transformations, including increased transaction transparency, enhanced liquidity, improved risk management capabilities, reduced entry barriers to the market, and more developed copyright protection. Using a Vector Autoregression (VAR) model, this paper clarifies the significant effects of fintech, especially the NFTs, on the size and profitability of the art market. The findings not only emphasize the importance of NFTs in developing the art market and increasing investment returns but also provide insights and constructive suggestions for the future growth and sustainable development of the art market. By fostering transparency, efficiency, and accessibility, fintech contributes to a more resilient and sustainable art market, ensuring its long-term prosperity and cultural enrichment.

For a long time, physicists always directly use mathematical tools to deal with physical problems, and few people pay attention to the difference between mathematical theory and physical theory. Just like the dilemma that physicists once faced when dealing with the problem of blackbody radiation function.By analyzing the difference between the theoretical basis of mathematics and the theoretical basis of physics, this paper draws the following conclusions: (1) The theoretical basis of mathematics and the theoretical basis of physics are different, so when we use mathematical tools for physics research, we need to be very careful. (2) Finiteness and discreteness should be the basis of the whole physical theory; This paper points out that it is not advisable to use infinite " " and infinitesimal "0" without restriction and demonstration in physics, as well as the continuity of functions, which will bring a lot of trouble to physical theory.At the same time, through the analysis of Banach-Tarski paradox and Bertrand paradox, this paper proposes that if we revise the basic assumptions of probability theory: assuming that "points" have quantized sizes, and "lines" also have quantized widths. After the correction, we can not only avoid the troubles caused by Bertrand paradox, but also make probability theory better for practical application.

Blocking the interaction of the SARS-CoV-2 spike protein with the human angiotensin-converting enzyme II (hACE2) protein serves as a therapeutic strategy for treating COVID-19. Traditional Chinese medicine (TCM) treatments containing bioactive products could alleviate the symptoms of severe COVID-19. However, the emergence of SARS-CoV-2 variants has complicated the process of developing broad-spectrum drugs. As such, the aim in this study was to explore the efficacy of TCM treatments for SARS-CoV-2 variants through targeting the interaction of the viral spike protein with the hACE2 receptor. The antiviral activity was systematically evaluated using a pseudovirus system. Scutellaria baicalensis was found to be effective against SARS-CoV-2 infection through affecting the interaction of viral spike protein with the hACE2 protein. The active molecules of S. baicalensis were identified and analyzed. Baicalein and baicalin, a flavone and a flavone glycoside, respectively, found in S. baicalensis, exhibited strong inhibitory activities, targeting the viral spike protein or hACE2 protein, respectively. Under optimized conditions, virus infection was inhibited by 98% via baicalein-treated pseudovirus and baicalin-treated hACE2. In summary, we identified the potential SARS-CoV-2 inhibitors of the interaction of the Omicron spike protein and hACE2 receptor from S. baicalensis. Future studies on the therapeutic application of baicalein and baicalin against SARS-CoV-2 variants are needed.

In this paper, we present a complete, flexible and safe convex-optimization-based method to solve speed planning problems over a fixed path for autonomous driving in both static and dynamic environments. Our contributions are five fold. First, we summarize the most common constraints raised in various autonomous driving scenarios as the requirements for speed planner developments and metrics to measure the capacity of existing speed planners roughly for autonomous driving. Second, we introduce a more general, flexible and complete speed planning mathematical model including all the summarized constraints compared to the state-of-the-art speed planners, which addresses limitations of existing methods and is able to provide smooth, safety-guaranteed, dynamic-feasible, and time-efficient speed profiles. Third, we emphasize comfort while guaranteeing fundamental motion safety without sacrificing the mobility of cars by treating the comfort box constraint as a semi-hard constraint in optimization via slack variables and penalty functions, which distinguishes our method from existing ones. Fourth, we demonstrate that our problem preserves convexity with the added constraints, thus global optimality of solutions is guaranteed. Fifth, we showcase how our formulation can be used in various autonomous driving scenarios by providing several challenging case studies in both static and dynamic environments. A range of numerical experiments and challenging realistic speed planning case studies have depicted that the proposed method outperforms existing speed planners for autonomous driving in terms of constraint type covered, optimality, safety, mobility and flexibility.

Food-grinding occurs in rodents and is influenced by multiple-factors. However, the factors affecting this behavior remain unclear. In this study, we aimed to investigate the effect of food restriction on food grinding by Brandt’s voles (Lasiopodomys brandtii), as well as the potential role of the gut microbiota in this process, through a comparison of the variations between voles with different food supplies. Food restriction reduced the relative amount of ground food to a greater extent than it lowered the relative food consumption, and altered the abundance of Staphylococcus, Aerococcus, Jeotgalicoccus, and Un--s-Clostridiaceae bacterium GM1. Strong correlations between the ground-to-consumed food ratio and the abundance of fecal microbiota were found for Un--s-Clostridiaceae bacterium GM1 and Aerococcus. The content of fecal acetate and propionate for the 7.5 g-food supply group was lower than that for the 15 g-food supply group. Further, the relative amount of ground food and ground-to-consumed food ratio were both positively correlated with the acetate content. Our study indicated that food restriction can effectively inhibit food grinding. Further, Un--s-Clostridiaceae bacterium GM1 abundance, Aerococcus abundance, and acetate content were strongly related to food grinding. Variations in gut microbial abundance and metabolite short-chain fatty acid content induced by food restriction likely promote the inhibition of food grinding. These results could potentially provide guidance for reducing food waste during laboratory rodent maintenance.

Breast cancer is a complex and heterogeneous disease that displays diverse molecular subtypes and clinical outcomes. Although it is known that the location of tumors can affect their biological behavior, the underlying mechanisms are not fully understood. In our previous study, we found a differential methylation profile and membrane potential between left (L) and right (R)-sided breast tumors. In this current study, we aimed to identify the ion channels responsible for this phenomenon and determine any associated phenotypic features. To achieve this, experiments were conducted in mammary tumors in mice, human patient samples, and with data from public datasets. The results revealed that L-sided tumors have a more depolarized state than R-ones. We identified a 6-ion channel-gene signature (CACNA1C, CACNA2D2, CACNB2, KCNJ11, SCN3A, and SCN3B) associated with side: L-tumors exhibit lower expression levels than R-ones. Additionally, in silico analyses show that the signature correlates inversely with DNA methylation writers and with key biological processes involved in cancer progression, such as proliferation and stemness. The signature also correlates inversely with patients’ survival rates. In an in vivo mouse model, we confirmed that KI67 and CD44 markers were increased in L-sided tumors and similar tendency for KI67 was found in patient L-tumors. Overall, this study provides new insights into the potential impact of anatomical location on breast cancer biology and highlights the need for further investigation into possible differential treatment options.

Melittin, a natural antimicrobial peptide, displays a broad-spectrum antimicrobial activity, which has caused increasing attention as a potential antibiotic alternative. However, melittin has not been used widely at present due to its high hemolysis and low proteolytic stability. In this study, N-terminal fatty acid was conjugated to melittin to develop new melittin-derived lipopep-tides (MDLs) for improving the limitation of melittin. Our results showed that, the antimicrobial activity of MDLs was increased by 2 to 16 times compared with native melittin, and the stability of these MDLs against trypsin and pepsin degradation was increased by 50 to 80%. Besides, the hemolytic of the MDLs decreased when the length of the carbon chain of fatty acids exceeded 10. Among them, the newly designed analog Mel-C8 showed optimal antimicrobial activity and protease stability. The antimicrobial mechanism studied revealed that the MDLs showed a rapid bactericidal effect by interacting with LPS or LTA and penetrating the bacterial cell membrane. In conclusion, we designed and synthesized a new class of MDLs with potent antimicrobial activity, high proteolytic stability, and low hemolysis through N-terminal fatty acid conjugation.

In wideband radar systems, the performance of motion parameters estimation can significantly affect the performance of object detection and the quality of inverse synthetic aperture radar (ISAR) imaging. Although the traditional motion parameters estimation methods can reduce the range migration (RM) and Doppler frequency migration (DFM) effects in ISAR imaging, the computational complexity is high. In this paper, we propose a new fast non-searching motion parameters estimation method based on cross-correlation of adjacent echoes (CCAE) for wideband LFM signals. A cross-correlation operation is carried out for two adjacent echo signals, then the motion parameters can be calculated by estimating the frequency of the correlation result. The proposed CCAE method can be applied directly to the stretching system, which is commonly adopted in wideband radar systems. Simulational results demonstrate that the new method can achieve better estimation performances, with much lower computational cost, compared with existing methods. The experimental results on real radar data sets are also evaluated to verify the effectiveness and superiority of the proposed method compared to the state-of-the-art existing methods.

This study uses a mass-spring-damping system to simulate the repeated strain of liquefaction cyclic triaxial tests. The two results are compared in this paper to understand the feasibility of the mass-spring-damping system developed in this paper and the feasibility of future research on this related topic and development potential. The main factors affecting this mode's repeated strain are the spring coefficient k and the external force Q0. The spring coefficient has an inverse relationship but does not increase in multiples. The external force has a direct proportional relationship but does not increase the result- a non-multiple increase. When the pore water pressure of the liquefied cyclic triaxial test specimen rises, it will cause the specimen to liquefy, decreasing effective stress, shear modulus G, and damping ratio D, causing an increase in strain. The shear modulus and damping ratio are related to the spring coefficients k and c. Both are variables that change with time. This article takes an original thin-tube specimen at point A in the Yunlin area in Taiwan as a testing example. Through Mathematica software, it can be obtained that the mass m=1kg, the spring coefficient k=244e-0.1t kgf/cm, and the damping coefficient c=0.739e-0.257t kgf-s/cm and external force Q0=10.1sin2πt kg; Finally, this study selected the original thin-tube specimens from four locations in the Yunlin area, and simulated the repeated strain amount of the cyclic triaxial test specimens through a spring-damping system. The results show that the spring-damping system is feasible for simulated cyclic triaxial tests because the model is simple and the parameters are easy to understand and obtain, which also shows the extensibility of this model. Preliminary results of the research show that this model can further simulate the repeated strain obtained by cyclic triaxial tests without considering the increased trend in pore water pressure and the decrease in effective stress during cyclic loading.

Iris laevigata Fisch. is a perennial aquatic plant with strong cold resistance and showy flowers. However, the flowering period of a single flower is only two days, greatly limiting its potential use in landscaping and the cutting-flower industry. In addition, I. laevigata is often challenged with various abiotic stresses including high salinity and drought in its native habitat. Thus, breeding novel cultivars with prolonged flowering time and higher resistance to abiotic stress is of high importance. In this study, we first performed genome-wide identification of WRKYs, key transcription factors in modulating flowering time and abiotic stress responses. We overexpressed IlWRKY22 in Arabidopsis thaliana and found the flowering time was delayed in the transgenic plants. Molecular characterization further revealed that IlWRKY22 promotes the expression of CO and GA20OX genes in the photoperiod and gibberellin pathways, respectively, and inhibits the expression of SPL3 in the aging pathway. We also created transgenic Nicotiana tabacum overexpressing IlWRKY22, which showed significantly improved resistance to both salt and drought compared to control plants. Specifically, the photosynthetic rate, maximum potential quantum efficiency of Photosystem II (Fv/Fm), and chlorophyll content were higher in the transgenic plants, which was accompanied with higher antioxidant enzyme activity and lower levels of reactive oxygen species. Thus, our study revealed a unique dual function of IlWRKY22, an excellent candidate gene for breeding novel I. laevigata cultivars of desirable traits.

In the field of machine learning, cluster analysis has always been a very important technology for determining useful or implicit characteristics in the data. However, the current mainstream cluster analysis algorithms require comprehensive analysis of the overall data to obtain the best parameters in the algorithm. As a result, handling large-scale datasets would be difficult. This research proposes a distributed related clustering mechanism for Unsupervised Learning, which assumes that if adjacent data are similar, a group can be formed by relating to more data points. Therefore, when processing data, large-scale datasets can be distributed to multiple computers, and the correlation of any two datasets in each computer can be calculated simultaneously. Later, results are processed through aggregation and filtering before assembled into groups. This method would greatly reduce the pre-processing and execution time of the dataset; in practical application, it only needs to focus on how the relevance of the data is designed. In addition, the experimental results show the accuracy, applicability, and ease of use of this method.

An adaptive operation strategy for on-demand control of DMFC system is proposed as an alternative method to enhance the voltage stability. Based on a single-cell DMFC stack, a newly simplified semi-empirical model is developed from the uniform-designed experimental results to describe the I-V relationship. Integrated with this model, the multi-objective optimization method is utilized to develop an adaptive operation strategy. Although the voltage instability is frequently encountered in unoptimized operations, the voltage deviation is successfully decreased to a required level by adaptive operations with operational adjustments. Moreover, the adaptive operations are also found to be able to extend the range of operating current density or to decrease the voltage deviation according to ones requirements. Numerical simulations are implemented to investigate the underlying mechanisms of the proposed adaptive operation strategy, and experimental adaptive operations are also performed on another DMFC system to validate the adaptive operation strategy. Preliminary experimental study shows a rapid response of DMFC system to the operational adjustment, which further validates the effectiveness and feasibility of the adaptive operation strategy in practical applications. The proposed strategy contributes to a guideline for the better control of output voltage from operating DMFC systems.

This paper presents a piezoresistive pressure sensor with a shield layer for improved stability. Compared with the conventional piezoresistive pressure sensors, p-type piezoresistors are covered by an n-type shield layer, which is formed by ion implantation. The proposed pressure sensors have been successfully fabricated by bulk micromachining techniques. The impact of electrical field on piezoresistors is studied by simulation. The temperature drift of the pressure sensor has been investigated by both simulation and experimental measurement. Characteristics of developed pressure sensors are tested from -40 C to 125 C. A sensitivity of 0.022 mV/V/KPa and a maximum non-linearity of 0.085% FS are measured for the fabricated sensor in a pressure range of 1 MPa. The temperature coefficients of resistance of shielded piezoresistors are found to be smaller than those of un-shielded ones. It is demonstrated that the shield layer is able to reduce the drift caused by electrical field and ambient temperature variation.

This paper presents a theory on graph topological structure and graph coloring, proving that for any N-order graph structure (with a topological structure similar to ), the maximum number of colors required for coloring is less than or equal to . The Four Color Theorem is just one special case of this theory, with the maximum structure size for a four-color graph being a 4-order structure graph, hence requiring only a maximum of 4 colors for coloring.

This paper is the third application-oriented paper based on the "unified theory of forces" and also addresses the shortcomings of previous research in fully explaining the origin and nature of the weak force. The main conclusions of this paper are as follows: (1) It is argued that neutrinos are generated by the gravitational field, and their generation mechanism is similar to the radiation of photons from electron orbital transitions. Particles undergoing orbital transitions in a gravitational field will emit neutrinos. (2) We rigorously derive the energy formula for neutrinos and demonstrate that the energy formula for neutrinos does not comply with the Planck energy formula. Neutrinos with higher energy have longer wavelengths and are more easily observed in experiments.

Monitoring the status and dynamics of desertification is one of the most important parts of combating desertification. In this study, 30m high-resolution information on land desertification and restoration in the HRB was extracted from the land cover database. The results indicate that land desertification coexists with land restoration in the HRB. At different periods, the area of land restoration is much larger than the area of land desertification in the HRB, and the HRB has been in a process of land restoration. Upstream of the HRB, there is a continuing trend of increasing land desertification associated with overgrazing in a context where climate change favors desertification reversal. In the middle and lower reaches, although both climate variability and human activities favor land desertification, the process of land desertification in the middle and lower reaches is still being reversed and land restoration dominates. The implementation of the Eco-Environmental Protection Project and desertification control measures, especially the EWDP, is contributing to the reversal of desertification in the middle and lower reaches of the HRB. However, the EWDP has indirectly led to the lowering of the water table in the middle reaches, resulting in local vegetation degradation. Therefore, there is therefore an urgent need to transform the economic structure of the middle reaches to cope with water scarcity and land desertification.

Multiply-accumulate calculations using a memristor crossbar array is an important method to realize neuromorphic computing. However, the memristor array fabrication technology is still immature, and it is difficult to fabricate large-scale arrays with high-yield, which restricts the development of memristor-based neuromorphic computing technology. Therefore, cascading small-scale arrays to achieve the neuromorphic computational ability that can be achieved by large-scale arrays, which is of great significance for promoting the application of memristor-based neuromorphic computing. To address this issue, we present a memristor-based cascaded framework with some basic computation units, several neural network processing units can be cascaded by this means to improve the processing capability of the dataset. Besides, we introduce a split method to reduce pressure of input terminal. Compared with VGGNet and GoogLeNet, the proposed cascaded framework can achieve 93.54% Fashion-MNIST accuracy under the 4.15M parameters. Extensive experiments with Ti/AlOx/TaOx/Pt we fabricated are conducted to show that the circuit simulation results can still provide a high recognition accuracy, and the recognition accuracy loss after circuit simulation can be controlled at around 0.26%.

To understand the molecular mechanism underlying yellowing in pineapples during ripening, coupled with alterations in fruit quality, comprehensive metabolome and transcriptome investigations were carried out. These investigations were conducted using the pulp samples collected at three distinct stages of maturity: young fruit (YF), mature fruit (MF), and fully mature fruit (FMF). This study revealed a noteworthy increase in the levels of total phenols and flavones, coupled with a concurrent decline in lignin and total acid content, as the fruit transitioned from YF to FMF. Furthermore, the analysis yielded 167 differentially accumulated metabolites (DAMs) and 2194 differentially expressed genes (DEGs). Kyoto Encyclopedia of Genes and Genomes enrichment analysis based on DAMs and DEGs revealed that the biosynthesis of plant secondary metabolites, particularly the flavonol, flavonoid, and phenypropanoid pathways, plays a pivotal role in fruit yellowing. Additionally, a comprehensive regulatory network encompassing genes that contribute to metabolisms of flavones, flavonols, lignin, and organic acids was proposed. This network sheds light on the intricate processes that underlies fruit yellowing and quality alterations. These findings enhance our understanding of the regulatory pathways governing pineapple ripening and offer valuable scientific insight into the molecular breeding of pineapples.

This study focuses on the decisions of picking, inventory, ripening, delivering, and selling mangoes in a harvesting season. Demand, supply, and prices are uncertain, and their probability density functions are fitted based on actual trading data collected from the largest spot market in Taiwan. A stochastic programming model is formulated to minimize the expected cost under the considerations of labor, storage space, shelf life, and transportation restrictions. We implement the sample-average approximation to obtain a high-quality solution of the stochastic program. The analysis compares deterministic and stochastic solutions to assess the uncertain effect on the harvest decisions. Finally, the optimal harvest schedule of each mango type is suggested based on the stochastic program solution.

This paper presents a non-perturbative method for solving eigenproblems. This method applies to almost all potentials and provides non-perturbative approximations for any energy level. The method converts an eigenproblem into a perturbation problem, obtains perturbation solutions through standard perturbation theory, and then analytically continues the perturbative solution into a non-perturbative solution.

The dilatometer curves of continuous cooling transformation of 12Mn steel were measured with Formastor-FⅡthermal mechanical simulator．The steel's undercooled austenite phase continuous cooling transformation curves ( CCT curves) were established by means of the dilatometer method and the metallographic-hardness measurement method． The effect of cooling rate on microstructure and hardness of the steel was studied． CCT curve of test steel was simulated by JMatPro. The results show that the Ac1 and Ac3 of the experimental steel are 692 ℃ and 855 ℃ ; the microstructure obtained is made of ferrite，pearlite and bainite．The ferrite transformation and pearlite transformation occur at a slower cooling rate，in which the ferrite is dominant. When the cooling rate is greater than 4.25 ℃ / s bainite transformation happens．As the cooling rate increases，microstructure or grains become finer．The hardness of the tested steel with increasing cooling rate shows a trend of first fast increase and soon decrease．The simulation results are consistent with the measured CCT law. The high temperature mechanical properties of 12mn steel round billet were tested by gleeble-1500d thermal / mechanical simulator. The tensile strength, reduction of area and stress-strain curves of the billet were obtained in the range of 600-1300 ℃.

During the Covid-19 pandemic in Taiwan, analytical tools of PEST (political, economic, social-cultural, and technological), SWOT (strength, weakness, opportunity, threat), nine building blocks of a business model canvas, and knowledge management were combined to develop a theoretical framework, and used to assess business, smart and sustainable management of two case companies: Tung Sheng Company Limited and its subsidiary, Strong Basic Enterprise Limited. A heuristic inquiry research design was adopted. In addition to secondary data from the two case companies, major top managers were interviewed to reveal constructive questions about the existing business models and to re-interpret strategy. The results showed that case companies own capabilities of R & D (research and development) as a foundation to further apply new smart ICT (information and communication technology) and execute green manufacturing. Additionally, strong key partnerships are used to diversify business investment for leveraging on limited resources given current insufficient qualified employees. Resilient practices adopted new and green technology to help mitigate the negative impacts of the Covid-19 pandemic. This study provides a useful framework and practical information about how to examine business models, smart and sustainable management processes of the two case companies and to make adjustments in strategies for the future.

Panax notoginseng is a traditional Chinese medicine, and saponins are its main active ingredients. The content of saponins in flower of P. notoginseng is the highest in the whole plant. Minor ginsenosides have stronger pharmacological activity than main ginsenosides, but its content in nature is very low. We can use extracted total saponins from P. notoginseng flower as the substrate to produce minor ginsenosides by biotransformation method. In this study, we used the fungus Talaromyces flavus and its crude enzymes to transform the extracted total saponins of P. notoginseng flower. Through the qualitative and quantitative analysis of the transformation substrates and products, it was found that minor ginsenosides Gyp-XVII, ginsenosides C-Mc1, C-Mx1, F2, Rg3, 20(R)-Rg3, Rk1 and Rg5 were found in the products and the conversion rate of the major saponins in P. notoginseng flower ranged from 44.16 to 55.22%, the yields of the minor ginsenosides ranged from 0.05 to 3.24%. This study provided a good experimental idea, greatly increased the utilization rate of total saponins in P. notoginseng flower, and laid a foundation for promoting the wide application of minor saponins.

Micro-electro-mechanical systems (MEMS) are once proposed in 1970s and evolving rapidly. The current researchers are seeking for better designs and better applications of MEMS actuators. This work presents an electrostatic driven dual-axis scanning micromirror, i.e., two-dimensional (2D) scanning micromirror with a mirror size of 500 μm × 500 μm. The scanning mirror is implemented by using bulk micromachining process on silicon on insulator (SOI) substrate, which is compatible with present complementary metal oxide semiconductor (CMOS) manufacturing technology. The scanning frequencies of the slow and the fast axis are 4.87 kHz and 31.15 kHz, respectively. The impact factors of the dimensions of comb fingers and torsional beams are analyzed and discussed in this study. Under the driving voltage difference of 100 volts and 70 volts, the deviation angle is 4.57° × 13.08°. Therefore, a simple design of a dual-axis MEMS scanning micromirror is proposed, which can be precisely controlled without additional complex sensors or circuits.

Insulated Gate Bipolar Transistor (IGBT) may convey high current and sustain high breakdown voltages; it may provide high power control. In a sense, how IGBT demonstrates the capability of power control was not specifically described, and the equivalent bipolar junction transistors (BJT) activated by an applied bias to the insulated gate is intriguing. As seen in Figure 1, IGBT shows an equivalent circuit structure containing two types of BJT, (NPN-type Bipolar transistor and PNP-type Bipolar transistor), which can be modeled as diode-associated transistor. Apparently, as a bias applies to the controlling gate, the channel beneath the gate oxide gets strongly inversed and turns out to be conductive just like what happens on metal-oxide-silicon field effect transistor (MOSFET), which provides necessary igniting currents to both BJTs and thus causes high current gain flowing through them-selves from the bottom. A proposed and renewed formula provides addressing the above scenario and successfully fitting the measured data that forms the characteristic curves. Some parameters in the proposed formula, which includes size and mobility associated constant, threshold voltage, and Early-Voltage-related lambda for MOSFET, explain and explore the underlying physics. IGBT thus enjoy high input impedance and high current gain due to MOSFET (Insulated Gate) and BJT, respectively. This formula combines both merits of MOSFET and BJT in order to fit the measured data. Indeed, the formula intimately fits IGBT electrical characteristic curves, and thus may be qualified and served as a model. The new model is then advisable for designing power integrated circuit to exactly achieve power saving, power control, and power efficiency.

With the development of Internet, big data and artificial intelligence technology, personal information protection has become the focus of social attention. The legal boundary of data protection has become increasingly prominent, involving the collection, storage, use, transmission and disclosure of personal information. This paper aims to explore the legal boundary of data protection, analyze the legal basis, legal principles and legal provisions of personal information protection, and put forward corresponding legal suggestions, in order to provide reference for the improvement of China's data protection legal system.

Prestress loss evaluation in prestressed strand is essential for prestressed structures. However, the sensors installed outside the duct can only measure the total prestress loss. The sensors attached on strand inside the duct also have several problems, such as inadequate durability in an aggressive environment, vulnerable damage at tensioning and so on. This paper proposes a new installation method for long-gauge fiber Bragg grating (LFBG) sensor to prevent accidental damage. Then the itemized prestress losses were determined in each stage of the pre-tensioning and post-tensioning according to the LFBG measurements. We verified the applicability of the LFBG sensors for prestress monitoring and the accuracy of the proposed prestress loss calculation method during pre-tensioning and post-tensioning. In the pre-tensioning case, the calculated prestress losses had less deviation from the true losses than those obtained from foil-strain gauges, and the durability of the LFBG sensors was better than foil-strain gauges, whereas in post-tensioning case, the calculated prestress losses were close to those derived from theoretical predictions. Finally, we monitored prestress variation in the strand for 90 days. The itemized prestress losses at each stages of post-tensioning were obtained by the proposed calculation method to show the prospect of the LFBG sensors in practical evaluation.

This study aims to exploit the distinctive properties of carbon nanotube materials, which are particularly pronounced at the microscopic scale, by deploying fabrication techniques that allow their features to be observed macroscopically. Specifically, we aim to create a semiconductor device that exhibits flexibility and the ability to modulate its electromagnetic wave absorption frequency by means of biasing. Initially, we fabricate a sheet of carbon nanotubes through a vacuum filtration process. Subsequently, phosphorus and boron elements are separately doped into the nanotube sheet, enabling it to embody the characteristics of a PN diode. Measurements indicate that, in addition to the fundamental diode's current-voltage relationship, the device also demonstrates intriguing transmission properties under the TEM mode of electromagnetic waves. It exhibits a frequency shift of approximately 2.3125 GHz for each volt of bias change. The final result is a lightweight and flexible carbon-based semiconductor microwave filter, which can conform to curved surfaces. This feat underscores the potential of such materials for innovative and effective electromagnetic wave manipulation.

The quantified residence time distribution (RTD) provides a numerical characterization of mixing in the continue casting tundish, thus allowing the engineer to better understand the metallurgical performance of the reactor. This paper describes a computational fluid dynamic (CFD) modelling study for analyzing the flow pattern and the residence time distribution in a five-strand tundish. Two passive scalar transport equations are applied to separately calculate the E-curve and F-curve in the tundish. The numerical modelling results are compared to the water modelling results for the validation of the mathematical model. The volume fraction of different flow regions (plug, mixed and dead) and the intermixing time during the ladle changeover are calculated to study the effects of the flow control device (FCD) on the tundish performance. The result shows that a combination of the U-baffle with deflector holes and the turbulence inhibitor has three major effects on the flow characteristics in the tundish: i) reduce the extent of the dead volume; ii) evenly distribute the liquid streams to each strand and iii) shorten the intermixing time during the ladle changeover operation.

Abstract— Flight Control System is an integrated avionics system equipped with the minimum required components for an autonomous flight. This paper focuses on the Hardware Design of the Flight Control System and presents specific details of the components and its interface. The system architecture is based on Field Programmable Gate Array and Digital Signal Processor. Employing these two processors in the flight control system would improve the Flight Control System performance in terms of fast sequential processing of high-level control algorithms. In addition to Field Programmable Gate Array and Digital Signal Processor, the flight control computer system will also make use of Global Positioning System and Micro Electro Mechanical System sensors. The project will be implemented using Altera’s System On Programmable Chip builder, currently known as Qsys – Platform Designer implemented in Quartus-II. The system employs Nios-II processor which is 32-bit soft-core embedded-processor architecture designed especially for the Altera’s family of Field Programmable Gate Array. From conceptualization to final design, this paper presents the functionality of the different modulus and complex interfaces employed in this Flight Control System.

This study aims to explore the effect of real-time visual feedback (VF) information of the pres-sure of center (COP) provided by intelligent insoles on balance training in a one leg stance (OLS) and tandem stance (TS) posture. Thirty healthy female college students were randomly assigned to the visual feedback balance training group (VFT), non-visual feedback balance training group (NVFT), and control group (CG). The balance training includes: OLS, tandem Stance (dominant leg behind, TSDL), tandem stance (non-dominant leg behind, TSNDL). The training lasted 4 weeks, the training lasts 30 minutes at an interval of 1 days. There was a sig-nificant difference in the interaction effect between Groups*Times of the COP parameters (p<0.05) for OLS. There was no significant difference in the interaction effect between Groups*Times of the COP parameters (p>0.05) for TS. The main effect of the COP parameters was a significant difference in Times (p<0.05). The COP displacement, velocity, radius, and area in VFT significantly decreased after training (p < 0.05). Therefore, the visual feedback technology of intelligent auxiliary equipment during balance training can enhance the benefit of training. The use of smart wearable devices in OLS balance training may improve the visual and physical balance integration ability.

The surface behavior of the ZnO-based films could be modulated via a postannealing and ultraviolet (UV) irradiation with different powers and time, respectively. These present results could provide modulate the microstructure related in grain-size distribution and photocatalytic behavior for potential guide in the field of wide bandgap semiconducting oxides. The ZnO films were prepared onto Corning-1737 glass substrates by using radio-frequency magnetron sputtering without supplying oxygen source at room temperature. For the purpose of obtaining modulable grain microstructures, the as-prepared ZnO films (Z0) were treated via a postannealing modification in vacuum furnace at 300°C for 30 minutes after deposition (Z300) accompanied with the adjustable internal stress. The contact angle (CA) value of ZnO film reduced from 95° to 68° was owning to the different grain microstructure accompanied by a change in size variation. In addition, the UV light with different irradiation powers could also be used to improve the hydrophilicity varied from hydrophobic status to superhydrophilic status due to the desirable surface characteristics of the photocatalytic action. In addition, the photocatalytic activity of ZnO film exhibited efficient photodegradation of methylene blue (MB) under UV irradiation, with a chemical reaction constant of 2.93×10-3 min−1. In this present work, we demonstrated that the CA value of the ZnO films not only caused from hydrophobic to hydrophilic status accompanied by a change in grain size combined with internal stress but also induced by the UV light irradiation combined with photocatalytic activity simultaneously. On the other hand, the enhanced surface plasmonic resonance could be observed that is due to couple electron and photon oscillations and can be generated at the interface between a flat, continuous Pt capping nanolayer. This designed structure could also be considered as a Pt electrode pattern onto ZnO (metal Pt/ ceramic ZnO) for multifunctional heterostructured sensors and devices in near future.

Often, engineers with machining experience often judge machining state and tool life according to chips’ features. Engineers' experience is digitized in this study. During the cutting process, the cutting tool coming in contact with the workpiece produces a shear zone, which causes plastic deformation and shear slip. The chips closest to the shear zone can directly show the state of the tool and workpiece when the material is SKD61. This study used chip color, vibration, and current signal integration for prediction of machining state and cutting tool life. When the cutting tool wears increased, the chip surface color changed in the following way: purpleè purple blueè blue ècyan, or even green and yellow. When the cutting tool was in the accelerating wear phase, the color change was particularly obvious. The Back-Propagation Levenberg–Marquardt (BP-LM) predictive methodology was used to compare the predictive ability of voltage, vibration signal, and chip color. The Mean Absolute Percentage Error (MAPE) for the voltage signal was 12.28%, for the vibration signal it was 11.38%, and for the chip color combined with multi-sensor characteristics it was 7.85%. The MAPE of the chip color was the smallest. Using the General Regression Neural Network (GRNN) methodology, the MAPE for the voltage signal was 10.74%, for the vibration signal 7.96%, and for the chip color combined with multi-sensor characteristics was 6.59%. The MAPE of the chip color was the smallest. Obviously, the chip color combined with multi-sensor signals provided better predictive results than the vibration signal or voltage signal alone. There is currently no research on the usefulness of monitoring chip color for tool life prediction.

Abstract: Steamed ginseng water (SGW), the by-product generated from the heated processing of red ginseng, with high content of active substances, better skincare activities, and large amount output ineffective utilization, resulted in environmental pollution and resource waste. In current study, UHPLC-Q-Exactive-MS/MS liquid chromatography-mass spectrometry and multivariate statistical analysis were conducted to characterize the compositional features of the repeated thermal-treated SGW. The total sugar content, total sugar content, total reducing sugar content, total non-reducing sugar content, DPPH, ABTS+, Fe3+ reducing capacity, and the hydroxyl radical scavenging abilities were employed to evaluate the gross contents variation connect with anti-oxidant activities during heat processes. The result revealed the SGW content and antioxidant activity were highly correlated, the 7th SGW sample showed the highest content and the strongest ability on anti-aging capacities. 38 significant common differential markers were screened, by the four compared SGW groups (1- and 3-, 1- and 5-, 1- and 7-, and 1- and 9) through OPLS-DA analysis. The current study showed that the thermal proceeding times could be a vital index value during the recycling operation quality control of SGW, which has a huge potential in anti-aging cosmetic raw materials, In the meanwhile, our results provided a green, sustainable, low-cost thinking of rational application on ginseng resource.

Abstract In order to solve the problem that it is difficult to obtain the accurate trigger signal moment when using the time difference of UAV flight acoustic signals collected by acoustic sensors arranged in advance to locate the position of UAVs when they cannot be tracked by radar and are difficult to be observed by the human eye, an acoustic source localisation method with improved empirical modal decomposition (REMD) under an adaptive frequency window is proposed. Firstly, the collected UAV flight signals are smoothed and filtered, then the robust empirical modal decomposition (REMD) is used for IMF modal decomposition and spectral analysis of the collected signals, and a panning frequency window with variable bandwidth is introduced for corresponding frequency locking and extracting the IMFs; the GWO optimisation is used and the sliding metrics are set to determine the position of the panning frequency window automatically; finally, the extracted Finally, the extracted IMF components are reconstructed according to the criterion, and the trigger signal moments in the reconstructed IMF components are resolved and recorded, and the algorithm is used to calculate the difference between the reception moments of different sensors; for the traditional sound source localisation algorithms with a small detection range, which are prone to fall into the no-solution or false-solution, i.e., unable to achieve the localisation, a weighted least-squares-based Chan-Taylor algorithm is proposed for the localisation computation, and a weighted least-squares algorithm is proposed for the localisation computation, through the Inputting the sensor delay parameter and solving the linear equation system to get the target position information; finally, this paper verifies the robustness and performance of the design method with simulated and actual signals. The results show that the maximum positioning error is no more than 5% in an area with a side length of 15m in the measurement area. With the improved accuracy of time delay estimation, the positioning simulation results meet the positioning requirements even though the positioning error is further expanded when the measurement area is further expanded.

The study addresses the urgent environmental issue of climate change, focusing specifically on the role of local food, which is produced and consumed locally, helps reduce carbon emissions by eliminating the need for long-distance transportation. Through quantitative analysis, this study elucidates the potential benefits in environmental impact achieved through the consumption of local food: the significant reduction in carbon emissions. Specifically, the consumption of local food is found to yield an annual decrease of 2,421,296 tCO2 emissions, representing 2.5% of South Korea’s total greenhouse gas emissions from the transportation sector. This reduction further translates into an estimated economic value of USD 54.23 million (KRW 70.5 billion). This study underscores the potential of local food consumption as a tangible strategy to overcome environmental problems. Moreover, its academic contribution lies in its comprehensive analysis of the economic and empirical impacts of local food consumption on environment. Moving forward, we propose policies such as supporting local food distribution networks, providing public education on local food, fostering the local food industry, and providing incentives to revitalize local food consumption.

A PLS-based quality prediction method is proposed for batch processes using two-dimensional extended windows. To realize the adoption of information in the direction of sampling time and batch, a new definition region of support (ROS), k-i-back-extended region of support (KIBROS), is proposed to establish the extended window, which including the data of the previous sampling times in the same batch, the data of the same sampling time in the historical batches, the data of the previous sampling times in the historical batches and the data of the later sampling times in the historical batches. According to these regions of support, extended windows are established, and different models are proposed based on the extended windows for batch processes quality prediction. Further, using a typical batch process as an example, the injection molding process, the proposed quality prediction method is experimentally verified, proving that the proposed methods have higher prediction accuracy than the traditional method and the prediction stability is also improved.

Aluminum wire is a common material for wire bonding due to its resistance to oxidation and low price. It does not melt when becoming a free air ball (FAB) during the electronic flame-off (EFO) process with wettability, and is applied by wedge bonding. This study used 20μm Zn-Coated Al-0.5wt.%Si (ZAS) wires to improve the FAB shape after the EFO process, while maintaining stability of the mechanical properties, including the interface bonding strength and hardness. In order to test circuit stability after ball bonding, the current-tensile test was performed. During the experiment, it was found that 80nm ZAS with wire bonding has lower resistance and higher fusing current. For the bias tensile test, the thicker Zn film diffused into the Al-Si matrix easily, after which the strength was reduced. The ball-bond interfaces had no change in their condition before and after the bias. Accordingly, ZAS could be a promising candidate for ball bonding in the future.

ccurate recording of growth indicators for aquaculture species at different stages is essential for evaluating aquaculture production effectiveness and the rationality of feed formulations. Due to their convenience and non-invasiveness, weight, length, and condition factor are commonly used to assess the growth of aquaculture species . However, fish growth indicators, can vary significantly with age structure and feed components(nutrition), and relying on a single indicator may lead to misjudgments . In this study we investigated the growth indicators of gibel carp (Carassius auratus gibelio var. CAS V) at different growth stages (juvenile and adult) and different feed formulations. Meanwhile, fish weight-length relationship () was used to assess the growth indicators. The results showed that the weight-length relationship of gibel carp varied significantly with age and feed formulations. Additionally, the condition factor calculated depended on the weight-length relationship was more consistent with weight/length changes than measured. Weight analysis indicated that both weight, length, height, back thickness, and carcass ration had higher weights in analyzing fish growth. Therefore, during aquaculture production, fish growth evaluating requires considering diverse indicators such as weight, length,body height, back thickness, carcass ration,as well as condition factor to avoid misjudging the actual growth situation. Meanwhile, the use of the condition factor should consider the sufficient amount of data and whether the assumptions (such as being in a isometric growth period) are met.

Interstitial lung disease (ILD) is one of the most serious extra-articular complications of rheu-matoid arthritis (RA), which increases the mortality of RA. Because the pathogenesis of RA-ILD remains poorly understood, appropriate therapeutic strategies and biomarkers have not yet been identified. Thus, the goal of this review was to summarize and analyze the reported data on the etiology and pathogenesis of RA-ILD. The incidence of RA-ILD increases with age, and is also generally higher in men than in women and in patients with specific genetic variations and eth-nicity. Lifestyle factors associated with an increased risk of RA-ILD include smoking and exposure to pollutants. The presence of an anti-cyclic citrullinated peptide antibody, high RA disease activity, and rheumatoid factor positivity also increase the risk of RA-ILD. We also explored the roles of biological processes (e.g., fibroblast–myofibroblast transition, epithelial–mesenchymal transition, and immunological processes), signaling pathways (e.g., JAK/STAT and PI3K/Akt), and the his-topathology of RA involved in RA-ILD pathogenesis based on published preclinical and clinical models of RA-ILD in animal and human studies.

While pioglitazone reduces insulin resistance and hepatic gluconeogenesis effectively in patients with T2DM, these benefits remained controversial in patients with ESRD. We compared MACCEs and mortality (overall, infection-related, and MACCE-related) of pioglitazone to that of DPP4-inhibitors in patients with T2DM and ESRD. From Taiwan’s national health insurance database, 647 pioglitazone users and 6080 DPP4-inhibitors users between April 1st, 2006 and December 31th, 2016 were followed from the 91th date after the ESRD certification till study outcomes, independently; withdraw from the NHI program, death, or Dec. 31th, 2017. After weighting, risks of MACCEs (10.48% vs 12.62% per person-years, [HR]: 0.85, 95% [CI]: 0.729–0.985) and all-cause mortality (12.86% vs 13.22% per person-years, [HR]: 0.88, 95% [CI]: 0.771–0.995) are significantly lower in pioglitazone group. Subgroup analysis found lower MACCEs risk in the pioglitazone users without insulin therapy (6.44% vs 10.04% [HR]: 0.59, 95% [CI]: 0.42–0.82) and lower MACCEs related death (2.76% vs 3.84% [HR]: 0.61, 95% [CI]: 0.40–0.95) in the pioglitazone group with dyslipidemia, when comparing with DPP4-inhibitors users. Pioglitazone is associated with lower all-cause mortality and MACCEs in diabetic patients with ESRD, compared to DPP4-inhibitors. These benefits were further significant in the non-insulin users and patients with dyslipidemia.

Background: We aimed to evaluate the effect of early pelvic binder use in emergency management of suspected pelvic trauma, compared with the conventional stepwise approach. Methods: We enrolled trauma patients with initial stabilization using a pelvic binder for suspecting pelvic injury. Inclusion criteria were traumatic injury requiring a trauma team and at least one of the following: loss of consciousness or Glasgow coma score (GCS) < 13; systolic blood pressure < 90 mmHg; falling from ≥6 m; injury to multiple vital organs; and suspected pelvic injury. Various parameters, including gender, age, mechanism of injury, GCS, mortality, hospital stay, initial vital sign, revised trauma score, injury severity score, and outcome, were assessed and compared with historical controls. Results: A total of 204 patients with high-energy multiple-trauma from single level I trauma center in North Taiwan were enrolled in the study from August 2013 to July 2014. The two group baseline patient characteristics were all collected and compared. The trauma patients with suspected pelvic fractures initially stabilized with a pelvic binder had shorter hospital and ICU stays. The study group achieved statistically significantly improved survival and lower mean blood transfusion volume and mortality rate although they were more severe in the trauma score. Conclusions: We recommend prompt pelvic binder use for suspected pelvic injury before definitive imaging is available, as a cervical spine collar is used to protect the cervical spine from further injury prior to definitive identification and characterization of an injury.

Arid- and semi-arid Central Asia is particularly sensitive to climate change. The changes in extreme precipitation in Central Asia stemming from climate warming are the subject of intense debate within the scientific community. This study employed a Morlet wavelet analysis to examine the annual occurrence number of extreme precipitation in Central Asia from May to September during the period of 1951–2005. Their modulating planetary-scale climate modes were identified by using a linear regression analysis. Two major scales of the temporal variability were derived: 2–3.9 yr and 4–6 yr. The dominant variability was 2–3.9-yr scale and was associated with the negative phase of the Polar/Eurasia (POL) pattern. The 4–6-yr scale provided a secondary contribution and was closely linked to the negative phase of the North Atlantic Oscillation (NAO). These planetary climate modes acted as precursors of extreme precipitation over Central Asia. The negative phase of POL directly contributed to a negative height anomaly over Central Asia, which was intimately related to extreme precipitation. In contrast, the negative NAO phase possibly manifested as a Rossby wave source, which was subsequently exported to Central Asia through a negative–positive–negative Rossby wave train.

The goal of the current study is to analyse several nonlinear two-dimensional time-fractional Rosenau Hymanequations. The two-dimensional fractional Rosenau-Hyman equation has extensive use in engineering and applied sciences. The fractional view analysis of two-dimensional time-fractional Rosenau-Hyman equations is discussed using the homotopy perturbation approach, adomian decomposition method, and Yang transformation. Some examples involving two-dimensional time-fractional Rosenau-Hyman equations are provided in order to better understand the suggested approaches. The solutions appear as infinite series. We offer a comparison between the accurate solutions and those that are generated employing the proposed approaches in order to demonstrate the effectiveness and applicability of the proposed techniques. The results are graphically illustrated using 2D and 3D graphs. It has been noted that the obtained results and the targeted problems real solutions are quite similar. Calculated solutions at various fractional levels describe some of the problems useful dynamics. Other fractional problems that arise in other fields of science and engineering can be solved using a modified version of the current techniques.

Although the positive relationship between religion and environmental behavior is well-argued, empirical research about the relationship between religion and public pro-environmental behavior is relatively lacking. This paper aims to explore the group differences in the influence of religion on public pro-environmental behavior and the mediating role of environmental risk perception in religion and public pro-environmental behavior. Using the Chinese General Social Survey data in 2013 for empirical analysis, this study’s results show that there are group differences in the impact of religion on public pro-environmental behavior. Women with religious beliefs are more willing to engage in public pro-environmental behavior than those without religious beliefs. Religious believers over the age of 45 are more willing to participate in public pro-environmental behavior than those without religious beliefs. Political participants with religious beliefs are more willing to practice public pro-environmental behavior than those without religious beliefs. In addition, we found that environmental risk perception can act as partial mediation in religious and public pro-environmental behavior. In other words, religious beliefs are deeply embedded in local political and social culture. In order to correctly understand the relationship between religion and public pro-environmental behavior, it is necessary to consider religion in a specific cultural background.

As the most important component of soft robot, the pneumatic actuator can drive robot movement. However, the effect of the actuator pneumatic network geometry on the actuator load capacity is insufficient. In this paper, the finite element analysis method is applied to calculate the load force and stability torque of the pneumatic actuator under a wide range of length and height dimensions of the pneumatic network. The effect of the network size on the structure rigidity, load capacity and deformation of the actuator is analyzed. Based on the calculation results, the effect of network structure size on the deformation and load capacity is analyzed, and the optimal geometric results with the maximum load capacity are obtained. This study provides theoretical guidance for the structural design and optimization of the pneumatic actuator.

This paper studies an effective finite difference scheme for solving two-dimensional Heston stochastic volatility option pricing model problems. A dynamically balanced up-downwind strategy for approximating the cross-derivative is implemented and analyzed. Semi-discretized and spatially nonuniform platforms are utilized. The numerical method comprised is simple, straightforward with reliable first order overall approximations. The spectral norm is used throughout the investigation and numerical stability is proven. Simulation experiments are given to illustrate our results.

Amid escalating urbanization, devising rational commercial space layouts is a critical challenge. Leveraging machine learning, this study uses a Back-propagation (BP) neural network to optimize commercial spaces in Weinan City's central urban area. The results indicate an increased number of commercial facilities with a trend of multi-centered agglomeration and outward expansion. Based on these findings, we propose a strategic framework for rational commercial space development emphasizing aggregation centers, development axes, and spatial guidelines. This strategy provides valuable insights for urban planners in small and medium-sized cities in the Yellow River Basin and metropolitan areas, ultimately showcasing the power of machine learning in enhancing urban planning.

This study explored the effects of pBD114 (porcine β-defensin 114) on inflammatory response. The results in RAW264.7 cells showed that 100 μg/mL of pBD114 significantly increased the concentrations of TNFα and IL-10, and 10 μg/mL of pBD114 significantly decreased the concen-tration of TNFα in LPS-induced RAW264.7 cell cultures at 10 ng/mL. These results suggest that pBD114 can exhibit pro-inflammatory or anti-inflammatory activities under certain conditions. RNA-seq analysis was performed to gain further insight into the effects of pBD114 on the in-flammatory response. Among pBD114 promoting RAW264.7 pro-inflammatory response, pBD114 significantly up-regulated 1170 genes and down-regulated 724 genes. KEGG enrichment found that the DEGs were significantly enriched in immune- and signal-transduction-related signaling pathways. PPI and KDA analyses revealed that Bcl10 and Bcl3 were the key genes. In addition, pBD114 significantly up-regulated 12 genes and down-regulated 38 genes in the an-ti-inflammatory response. KEGG enrichment analysis revealed that the DEGs were mainly en-riched in the "Cytokine-cytokine receptor interaction" signaling pathway, and PPI and KDA analyses showed that Stat1 and Csf2 were the key genes. The results of qRT-PCR verified those of RNA-seq. In vivo mice tests also confirmed the pro- or anti-inflammatory activity of pBD114. Although the inflammatory response is a rapid and complex physiological reaction to noxious stimuli, this study found that pBD114 plays an essential role in the inflammatory response mainly by acting on genes related to immunity, signal transduction, signaling molecules, and interactions.

Applied talent is not only a builder of human civilization but also a promoter of economic development. They not only need systematic and solid engineering theoretical knowledge but also rich engineering practical experience. Applied undergraduate colleges are the cradle for cultivating applied talent and shoulder the important mission of cultivating various types of applied talent for society. With the rapid development of higher education, the number of applied undergraduate institutions has sharply increased, but the quality of applied talent cultivated by them has shown a significant decline, which greatly restricts the pace of industrial development in the world. This article proposes a new concept of promoting the "three certificates" (graduation certificate, degree certificate, and skill certificate) education model in applied undergraduate colleges, which is of great significance for the country to cultivate composite talents with the ability of "product design, production management, and product processing" at the same time.

The primary considerations while producing rice (Oryza sativa L.) include improving its nutritional quality and production. To tackle widespread hunger globally, better nutritional, high-yielding rice cultivars need to be developed. The conventional ways are to increase the production of rice and add balanced nutrients in the daily diet to fulfill the need of yield and nutrient quality. This article focuses on nutritional strategies for rice and illustrates the availability of omics technologies. Current advancements providing many methodologies and approaches for exploring genetic resources and for understanding the molecular mechanisms involved in trait formation have been highlighted. Studying the genetic influences of various characteristics has been proven to expedite crop breeding processes. In this perspective, genome-wide association research, genome selection (GS), and QTL mapping are all genetic analysis that helps in increasing the nutritional content of rice. Implementation of several omic techniques are effective approaches to enhance and regulate the nutritional quality of rice cultivars. Advancements in different types of omics including genomics and pangenomics, transcriptomics, metabolomics, nutrigenomics, and proteomics are also relevant to rice development initiatives. This review article compiles genes, locus, mutants and all omic approaches for rice enhancement. This knowledge will be very useful for now and for the future regarding rice studies.

The uncertainty in the secondary path of an Active Noise Control (ANC) headphone affects the waterbed effect and stability of the feedback system. This study focuses on the uncertainty of the secondary path when real users wear headphones, and proposes a new uncertainty constraint based on the measured results of the secondary path transfer function under different wearing conditions of dummy head and limited subjects. This constraint and a cascaded second-order infinite impulse response filter with fixed coefficients are used to formulate a control strategic function, which is optimized by the Improved Grey Wolf Optimizer (IGWO) algorithm to obtain the optimal controller with better noise reduction performance. The proposed method and simulation model are validated based on the experimental test results. The results demonstrate that the safety factor and waterbed suppressing factor contained in the proposed uncertainty constraint ensures more stable noise reduction and effective suppression of the waterbed effect for new subjects without a priori data.

We present a design of electrostatic comb driver to improve and investigate its actuation performance. The proposed electrostatic comb actuator (ECA) is composed of two set of interdigitated comb microstructures, the inner combs are fixed to form the fish-bone microstructures and the outer combs are movable and connected to crab-leg flexure beams microstructures. The ECA is investigated to optimize the actuation performance by changing the comb shape and the intersection angle of crab-leg flexure beams. The comb shapes are compared between the traditional rectangle shape and the trapezoid shape, while the intersection angles of crab-leg flexure beams are compared between 45°, 60°, and 90° on the influences of ECA displacement and stability characteristics. These parameters are investigated for their impacts on the dynamic comb displacement and driving voltage. Under the condition of a driving DC bias voltage of 100 volts, the ECA displacement is firstly increased and then gradually decreased by increasing the comb finger length. The maximum displacement of ECA with trapezoid comb is 47.2 μm while that of ECA with rectangle comb is 22.4 μm. By using trapezoid comb shape to replace the rectangle comb under the same conditions, the ECA displacement is improved 2-fold. To enhance the stability of ECA system, the intersection angle of 90˚ of crab-leg flexure beams shows highest stability that is great better than the intersection angle of 45° and 60° of crab-leg flexure beams by increasing the driving different DC bias voltage to 100 volts on ECA. The stability of the ECA with the intersection angle of 90° of crab-leg flexure beams is enhanced 1.1-fold and 1.4-fold compared to that of 45° and 60° of crab-leg flexure beams, respectively. This design provides an optimized approach to the electrostatic comb actuator that can be used expansively in the gyroscope, motion sensor, position sensor, imaging sensor, optical sensor, and so on.

Whether there is any inclination between structures and functions of antimicrobial peptides (AMPs) is a mystery yet to be unraveled. AMPs have various structures associated with many different antimicrobial functions, including antibacterial, anticancer, antifungal, antiparasitic and antiviral activities. However, none has yet reported any antimicrobial functional tendency within a specific category of protein/peptide structures nor any structural tendency of a specific antimicrobial function with respect to AMPs. Here we examine the relationships between structures categorized by three structural classification methods (CATH, SCOP and TM) and seven antimicrobial functions with respect to AMPs using an enrichment analysis. The results show that antifungal activities of AMPs were tightly related to two-layer sandwich structure of CATH, knottin fold of SCOP, and the first structural cluster of TM. The associations with knottin and TM cluster 1 even sustained through the AMPs with a low sequence identity. Besides, another significant mutual enrichment was observed between the third cluster of TM and anti-gram-positive-bacterial/anti-gram-negative-bacterial activities. The findings of the structure-function inclination further our understanding of AMPs and could help us design or discover new therapeutic potential AMPs.

Quantitative determination of the critical size of inclined coal pillar in old goaf water affected area is of great significance for water damage prevention and safe mining. The critical size of inclined waterproof coal pillar is derived by using theoretical analysis, numerical calculation and field engineering practice for the stability of the waterproof coal pillar in old goaf water affected area of 1303 working face of Dananhu I mine in Xinjiang region. Firstly, a force model of inclined waterproof coal pillar was established to reveal the law that the critical size of the coal pillar increases with the increase of coal seam inclination under the action of asymmetric load. Then, numerical simulation was applied to reveal the dynamic evolution process of plastic deformation-destabilization-destruction of section coal pillar under the influence of mining and single-side water pressure, and the critical size of waterproof coal pillar in study area was determined to be 19.09m. Finally, measures such as pumping and pressure relief and slurry reinforcement were adopted to reduce the deformation rate of the roadway on side of waterproof coal pillar, which ensured the stability of the coal pillar and roadway and the safe recovery of the working face.

The key links of face recognition are digital image preprocessing, facial feature extraction and pattern recognition, this article aimed at the current problem of slow speed and low recognition accuracy of face recognition , from the above three key links, on the basic of analyzing the therories of Fractional Differential Masks Operator (FDMO), Principal Component Analysis (PCA) and Support Vector Machine (SVM), design a kind of FDMO+PVA+SVM coupling algorithm that applies to face recognition to improve the speed and accuracy of it. To realize FDMO+PCA+SVM coupling algorithm, first, we should apply FDMO to face image processing binary marginalization, the purpose is getting face contour; Then, we apply PCA to get the feature of face image which is disposed by binary marainalization. At last, we can apply One-Against All of the SVM classifier and LibSVM software package to realize face recognition. Beside, the article with nine different coupling algorithm design four groups of experimental reaults on the ORL face database verified by comparative analysic FDMO+PCA+SVM coupling algorithm in the superiority of face recognition accuracy and speed.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

The article describes the rational for inhibition of the angiotensin-converting enzyme 2 (ACE2) pathways as specific targets in patients infected by SARS-CoV-2 in order to prevent the establishment of positive feedback loops triggered by COVID-19 in some predisposed subjects. Making use of a large quantity of published reports in which human/rodent ACE2 pathway inhibitors were administered in vivo, it is hypothesized a possible therapeutic pharmacological intervention through an inhibition strategy of the zinc metalloprotease ACE2 and its downstream pathway for SARS-CoV-2 patients. Of even more interest, metal (zinc) chelators and renin inhibitors (both FDA approved drugs) may also work alone or in combination in inhibiting the positive feedback loops, initially triggered by COVID-19 and subsequently sustained by hypoxia independently on viral trigger, when both arms of renin-angiotensin system (ACE2 and ACE) are upregulated, leading to critical, advanced and untreatable stages of the disease.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

The performance of Yttrium-Barium Copper Oxide (YBCO) high-temperature superconductors in high-frequency applications is significantly affected by the microwave surface resistance (Rs). The paper delves into the basics, measuring methods and factors affecting the resistance (Rs) in YBCO, highlighting its high critical temperature (Tc) and low resistance, positioning it as a promising material. YBCO's compatibility with epitaxial growth and microstructure engineering offers opportunities to reduce grain boundary effects and improve Rs, making it advantageous for high-frequency electronics, communication systems, and MRI coils. This is due to its high critical current density (Jc) and exceptional Rs at practical temperatures. Challenges remain in comprehending and managing Rs in YBCO, despite its favorable characteristics. Utilizing advanced fabrication methods and incorporating nanotechnology allow for customization of YBCO-based devices. Multi-scale modeling and simulation are essential for guiding experimental work and understanding YBCO's performance in high-frequency settings. This study highlights the promise of YBCO for future high-frequency technologies and stresses the importance of more research to overcome hurdles and fully exploit its capabilities, potentially transforming superconducting devices for practical use.

Distributed deformation based on Fiber Bragg Grating sensors or other kinds of strain sensors can be used to evaluate safety in operating periods of bridges. However, most of the published researches about distributed deformation monitoring are focused on solid rectangular beam rather than box girder—a kind of typical hollow beam widely employed in actual bridges. Considering that the entire deformation of a single-cell box girder contains not only bending deflection but also two additional deformations respectively caused by shear lag and shearing action, this paper again revises the improved conjugated beam method (ICBM) based on the LFBG sensors to satisfy the requirements for monitoring two mentioned additional deformations. The best choice for the LFBG sensor placement in box gilder is also proposed in this paper due to strain fluctuation on flange caused by shear lag effect. Results from numerical simulations show that most of the theoretical monitoring errors of the revised ICBM are 0.3%~1.5%, and the maximum error is 2.4%. A loading experiment for a single-cell box gilder monitored by LFBG sensors show that most of the practical monitoring errors are 6%~8%, and the maximum error is 11%.

This paper mainly explores the feasibility of using desert sand (DS) and recycled aggregate in cement stabilized base. Recycled coarse aggregate (RCA) and DS serve as the substitutes of natural coarse and fine aggregates, respectively, in cement stabilized base. A four-factor and four-level orthogonal test is designed to analyze the unconfined compressive strength, splitting tensile strength, and compressive resilient modulus. Furthermore, this paper investigates the effects of cement content, fly ash (FA) replacement rate, RCA replacement rate, and DS replacement rate on the road performance of cement stabilized base composing of RCA and DS. The test results reveal that the performance of cement stabilized base with partial RCA instead of natural coarse aggregate (NCA) and partial DS instead of natural fine aggregate satisfy the road use. Meanwhile, DS is beneficial to improve the strength of cement stabilized base. The correlation and microscopic analyses of the test results imply the feasibility of applying DS and recycled aggregate to cement stabilized base. It is hoped that this paper can offer a solid theoretical foundation for promoting the application of DS and recycled aggregate in road engineering.

In this research, catalytic steam reforming acetic acid derived from the aqueous portion of bio-oil for hydrogen production was investigated by using different Ni/ATC (Attapulgite Clay) catalysts prepared by precipitation, impregnation and mechanical blending methods. The fresh and reduced catalysts were characterized by XRD, N₂ adsorption-desorption, TEM and H₂-TPR. The comprehensive results demonstrated that the interaction between active metallic Ni and ATC carrier was significantly improved in Ni/ATC catalyst prepared by precipitation method, and in which the mean Ni particle size was the smallest (~13 nm) resulted in the highest metal dispersion (7.5%). The catalytic performance of the three catalysts was evaluated through the process of steam reforming of acetic acid in a fixed-bed reactor under atmospheric pressure at two different temperatures, such as 550 ℃ and 650 ℃. Results showed that the Ni/ATC (PM-N/ATC) prepared by precipitation method, achieved the highest H₂ yield of ~82% and little lower acetic acid conversion efficiency of ~85% than that (~95%) of Ni/ATC (IM-NATC) prepared by impregnation method. In addition, the deactivation catalysts after reaction for 4 h were analyzed by XRD, TGA-DTG and TEM, which demonstrated that the catalyst deactivation was not caused by the amount of carbon deposition, but owed to the significant agglomeration and sintering of Ni particles in the carrier.

Water pollution, intensified by the release of hard-to-degrade pollutants, poses severe threats to ecosystems, human health, and economic development. The existing advanced oxidation processes often involve high operational costs and may result in secondary pollution, highlighting the necessity for innovative and more sustainable solutions. To address these challenges, our study introduces a cost-effective and eco-friendly corona discharge barrier plasma discharger for wastewater treatment. Through the central composite design/response surface methodology, a high decolorization rate of 98% of methylene blue (MB) within 10 minutes was achieved by optimizing parameters such as pH and voltage. Furthermore, the mechanisms of the generation of reactive oxygen species via this device was discussed in detail and the degradation pathways of MB were described. Moreover, this device is also very energy-efficient, with a low energy density and electrical energy per order of 0.15 watt/mL and 5.79 kWh/m³/order, respectively. In conclusion, the plasma discharger developed in this study provides a cost-effective and environmentally sustainable solution for dye wastewater treatment. This research contributes significantly to the advancement of sustainable dye wastewater management practices, offering an innovative method that meets both environmental and economic objectives.

To overcome the temperature effect of NaI(Tl) detectors for energy spectrometry without additional hardware, a new correction method was put forward based on pulse deconvolution, trapezoidal shaping and amplitude correction, named DTSAC. To verify this method, actual pulses from a NaI(Tl)-PMT detector were measured at different temperatures from -20℃ to 50℃. Pulse processing and spectrum synthesis showed that the position drift of the 662 keV peak was less than 3 keV, and the corresponding resolution at 662 keV of the sum spectra ranges from 6.9% to 10.60% with trapezoidal width set as 1000 ns to 100 ns. The DTSAC method corrects temperature effect by pulse processing, and need no reference peak, reference spectrum and additional circuits. The method solves the problem of correction of pulse shape and pulse amplitude at the same time, and can be used even at high counting rate.

Innovations and improvements in hydraulic fracturing and horizontal well technologies have contributed to the success of the shale gas industry; however, the industry is also challenged by freshwater use and environmental health issues. Increasing water impact makes precise quantification of water consumption important. The objective in this study was to better understand water sustainability and availability of the projected shale gas from 2018 to 2030 in the Weiyuan play, China. The water footprint framework was used to quantify the potential water use and environmental impacts on different time scales. The results showed that the water use per well ranged from 11351.3 to 60664.73 m3, with a median of 36013.94 m3, totaling ~3.44 Mm3 for 97 wells. Yearly evaluation results showed that the gray water footprint was the main contributor and accounted for 83.82% to 96.76%, which was dependent on different scenarios of treatment percentages. The monthly environmental impact results indicated that the annual streamflow statistics were more likely to prevent water withdrawal. Water quality issues may be alleviated through recycling and retreatment measures that improve current waste water management strategies. Resource regulators should manage their water resources by matching water demand to water availability or replenishment.

Accurately estimating shrub biomass in arid and semi-arid regions is critical for understanding ecosystem productivity and carbon stocks at both local and global scales. However, capturing the shrub biomass accurately by satellite observations is challenging due to the short and sparse features of shrubs. In this study, we presented a framework to estimate shrub biomass at a 10m spatial resolution by integrating ground in-situ data, unmanned aerial vehicle (UAV), Sentinel-2, and Sentinel-1 observations. The pilot study was conducted in the Helan mountains of Ningxia province, China. First, the spatial distribution map of shrubland and other land cover types was generated in 2023. Then, a prediction model of shrub biomass was developed in a Random Forest Regression (RFR) approach driven by different predicted variable datasets based on in-situ measurements, UAV, and satellite images. Finally, the developed model was used to produce the biomass map of shrubland in 2023. The uncertainty was characterized by creating a standard deviation (SD) map using the Leave-One-Out Cross-Validation (LOOCV) method in the shrub biomass estimates. The resultant shrubland distribution map in 2023 has an F1 score of 0.92. The shrub biomass model driven by spectral bands and vegetation indices (R2= 0.62) demonstrated superior performance than that only driven by spectral bands (R2=0.33) or vegetation indices (R2=0.55). The uncertainty of the estimated biomass was lower than 4%, with the lowest values (<2%) happening in the high shrub coverage (>30%) and biomass production (>30kg/m2) regions. Furthermore, the findings show that the magnitude of shrub biomass was affected by the aridity and precipitation significantly in the study region. This study provides a workflow to accurately monitor the biomass of shrublands in a complicated environment based on remote sensing images from multi-platform observations.

Gaze tracking of high-speed moving targets is a novel application mode for low Earth orbit microsatellites. In this mode, small satellites are equipped with high-resolution narrow-field-of-view video cameras for stable gaze-tracking imaging of high-speed moving targets. This paper proposes a high-precision attitude adaptive integral sliding mode control method with a feedforward compensation disturbance observer to enhance the capability of a microsatellite attitude control system for gaze tracking of high-speed moving targets. Specifically, first, we present the attitude control system model for microsatellites and the calculation method for the desired attitude of target tracking based on image feedback. Then, an adaptive integral sliding mode attitude control algorithm with a feedforward compensation disturbance observer, which meets the requirements of high-precision tracking control, is designed. The developed algorithm utilizes the disturbance observer to observe the friction torque of the flywheel and compensates for it through feedforward control. It also employs the adaptive integral sliding mode control algorithm to reduce the impact of uncertain disturbances, decrease the steady-state error of the system, and enhance the attitude control precision. Simulation experiments demonstrated that the designed disturbance observer can successfully observe the frictional disturbance torque of the flywheel. The attitude Euler angle control precision for high-speed moving target tracking reached 0.009°, and the angular velocity control precision reached 0.005°/s, validating the effectiveness of the proposed approach.

This study aimed to investigate the relationship between sleep duration, dementia severity, age, and ANS regulation. This cross-sectional pilot study included 27 older patients with probable Alzheimer’s disease, hospitalized at a psychiatric center. We measured heart rate variability to assess ANS regulation at night, evaluated dementia severity using the Clinical Dementia Rating scale, and obtained sleep duration data from sleep diaries maintained by psychiatric nurses. The data were analyzed using repeated-measures generalized linear models with age, sex, dementia severity, and medication (antipsychotics) as covariates. A sleep duration of 7–8 h per night was associated with better ANS regulation than other sleep durations, as indicated by sympathovagal balance (p = 0.005). ANS dysregulation was characterized by a 20.7% increase in sympathetic nervous system activity and a 14.8% decrease in parasympathetic nervous system (PSNS) activity. We found a significant correlation between dementia severity and PSNS activity (p = 0.04) and observed an inverted U-shaped association between sleep duration and ANS regulation. This pilot study demonstrated that a sleep duration of 7–8 h per night may be critical in maintaining optimal ANS regulation. Bidirectional associations between sleep duration, inadequate sleep duration, aging, and ANS regulation warrant further investigation.

People wore clothes for warmth, survival and necessity in modern life as well but in modern era, eco-friendliness, shorten production time, design, and intelligence also matters. The seamless bonding technology strengthen the bond between fabrics in textiles, while Grey relational analysis (GRA) can be applied to fabrics to measure the relationship between data series and determine the closeness of each data series. In this study, polyurethane prepolymer, 2-Hydroxyethyl acrylate (2-HEA) as an end-capping agent, and n-octyl acrylate (ODA) as a photo-initiator were used to synthesize dual-curing polyurethane hot-melt adhesive. The Taguchi quality engineering and grey relational analysis used to discuss the influence of different mole ratio of NCO:OH, and the effect of the molar ratio of addition of octyl decyl acrylate on the mechanical strength. The Fourier transform infrared spectroscopy (FTIR) results showed the termination of prepolymer's polymerization reaction and the C=O peak intensity at 1730 cm-1 indicating the efficient bonding to main chain. The high molecular weight polymer (20,000-30,000) described by advanced polymer chromatography (APC) confirmed the polyurethane polymer bonded with octyl decyl acrylate to achieve the photo-thermosetting effect. The thermogravimetric analysis (TGA) results showed the thermal decomposition temperature of polyurethane hot melt adhesive also increased and highest pyrolysis temperature (349.89℃) for the polyhydric alcohols. The high value of shear strength (34.94 kg/cm2) as well as peel strength (1.68 kg/cm) were also observed in dual-cure photo-thermosetting polyurethane hot melt adhesive. The signal-to-noise ratio also used to generate the grey relational degree. It was observed that the best parameter ration of NCO: OH was 4:1 with 5 moles of monomer. The Taguchi quality engineering method was used to find the parameters of single quality optimization, and then the grey relation calculation was used to obtain the parameter combination of multi-quality optimization for thermosetting polyurethane hot melt adhesive. The study aims to meet the requirements of seamless bonding in textile factories and optimized experimental parameter design by setting target values can effectively increase production speed, reduce processing time and costs as well.

Over the past couple of decades, Global positioning system (GPS) technology has been utilized to collect large-scale data from travel surveys. As the precise spatiotemporal characteristics of travel could be provided by GPS devices, the issues of traditional travel survey, such as misreporting and non-response, could be addressed. Considering the defects of dedicated GPS devices (e.g., need much money to buy devices, forget to take devices to collect data, limit the simple size because of the number of devices, etc.), and the phenomenon that the smartphone is becoming one of necessities of life, there is a great chance for the smartphone to replace dedicated GPS devices. Although, several general reviews have been done about smartphone-based GPS travel survey in the literature review section in some articles, a systematic review from smartphone-based GPS data collection to travel mode detection has none. The included studies were searched from six databases. The purpose of this review is to critically assess the current literature on the existing methodologies of travel mode detection based on GPS raw data collected by smartphones. Meanwhile, according to the systematic comparison among different methods from data-preprocessing to travel mode detection, this paper could carefully provide the Strengths and Weaknesses of existing methods. Furthermore, it is the crucial step to develop the methodologies and applications of GPS raw data collected by smartphones.