This study numerically evaluated the long-term and stable trends of meandering channel planform at different mean annual subcritical flows based on a depth-averaged linearized meander evolution model. The calculation cases included an idealized sine-generated meander with moderate max-deflection angle and a typical natural meander - Jiyun River (in China). Within the increase of the selection of the mean annual width-depth ratio in a certain scope, the results showed some specific phase characteristics of channel centerline evolution: (1) the meander straightening trend became weaker in phase 1 (B/H ≤ 16.5) and gradually turned into the meander developing trend in phase 2 (B/H ≤ 27) with the overall immunity to flow magnitude; (2) the symmetric development form along the transverse direction perpendicular to the flow average direction was broken starting from the downstream tail in phase 3 (B/H ≤ 28.9), meantime accompanied by the highlight of flow effects when the mean annual B/H exceeded 28; (3) in phase 4 (B/H ≤ 29.5), there occurred obvious incipience and jump process of the channel sensitivity responding to flow when the selected B/H crossed 29.3, which were very similar to the transition process from the laminar flow to turbulent flow. Besides, the initial sinuosity and curvature-ratio indicator could contribute much to the channel evolutionary state, as demonstrated in the comparison between natural Jiyun River case and the correspondingly idealized sine-generated meander case with the same level of mean annual B/H. This research provides innovation spaces for deeper meander mechanism exploration and effective riparian management.

We conducted the meander evolution experiments incorporating the effects of riparian vegetation and the series of upper vortex flow disturbances induced by a scour pit simultaneously. Two employed nonlegume plants with salinity and alkalinity resistance, had uniform degrees of seedling normal growth and different lengths of root networks. Our results show that riparian vegetation in general can consolidate the single-thread channel planform without branching outward under the flooding flow conditions. Transverse point bars on inner banks were instead by downstream scroll bars in overall channel for long, unless the coupling of riparian vegetation and flood scour. Shallow-rooted plant was inadequate to resist the inner-bank cutting effect brought by the upper vortex flow. Deep-rooted plant can stabilize the bank-lines and thalweg significantly, but that was susceptible to locally low vegetation coverage. Using evolutionary spectral analysis based on thalweg, we found streamwise high-frequency distribution of bed topography mainly concentrated downstream the bifurcation interface in unvegetated scenario when faced with a flood, shrank to the upper isolated turning interface in shallow-rooted scenario, and conversely stood out along the bare roots disturbed region in deep-rooted scenario. This experimental study expands a much wider understanding of vegetation effects in hydro-bio-geomorphological systems engineering.

This study presents a novel approach for quantifying the dynamics of monthly hydraulic geometry relationships in the Jingjiang reach of the Yangtze River by integrating leaf area index (LAI) data as an indicator of riparian vegetation. A comprehensive system of ordinary differential equations (ODEs) couples traditional power-law hydraulic geometry equations with LAI, capturing the influence of erosion control on channel morphology. The periodic delayed response theory and automatic differentiation techniques are employed to enhance the modeling framework's capabilities. Calibration and verification demonstrate the models' effectiveness in capturing overall trends in discharge, width, and depth dynamics, outperforming traditional constant-parameter approaches. However, model predictive abilities are limited under extreme climate conditions due to training on normal climate data. Key assumptions, including the periodic delayed response theory's neglect of peak discharges, simplified representation of artificial cut-offs, and reliance on remotely sensed data with limited local validation, introduce uncertainties. The proposed modeling framework shows potential for broader application to other river systems with appropriate adjustments. Future research could incorporate additional environmental factors, integrate models across scales, couple with advanced simulation techniques, and expand stability assessments beyond the riverbed index. By addressing related challenges, this integrated approach lays a foundation for enhancing understanding of river morphodynamics and channel stability.

The speech-to-song illusion is a type of auditory illusion that the repetition of a part of a sentence would change people’s perception tendency from speech-like to song-like. The study aims to examine how pace, emotion, and language tonality affect people’s experience of the speech-to-song illusion. It uses a between-subject (Pace: fast, normal, vs. slow) and within-subject (Emotion: positive, negative, vs. neutral; language tonality: tonal language vs. non-tonal language) design. Sixty Hong Kong college students were randomly assigned to one of the three conditions characterized by pace. They listened to 12 audio stimuli, each with repetitions of a short excerpt, and rated their subjective perception of the presented phrase, whether it sounded like a speech or a song, on a five-point Likert-scale. Paired-sample t-tests and repeated measures ANOVAs were used to analyze the data. The findings reveal that a faster speech pace could strengthen the tendency of the speech-to-song illusion. Neither emotion nor language tonality show a statistically significant influence on the speech-to-song illusion. This study suggests that the perception of sound should be in a continuum and facilitates the understanding of song production in which speech can turn into music by having repetitive phrases and to be played in a relatively fast pace.

herein, we have compared the performance of SVM and MLP in emotion recognition using speech and song channels of the RAVDESS dataset. We have undertaken a journey to extract various audio features, identify optimal scaling strategy and hyperparameter for our models. To increase sample size, we have performed audio data augmentation and addressed data imbalance using SMOTE. Our data indicate that optimised SVM outperforms MLP with an accuracy of 82 compared to 75%. Following data augmentation, the performance of both algorithms was identical at ~79%, however, overfitting was evident for the SVM. Our final exploration indicated that the performance of both SVM and MLP were similar in which both resulted in lower accuracy for the speech channel compared to the song channel. Our findings suggest that both SVM and MLP are powerful classifiers for emotion recognition in a vocal-dependent manner.

In this paper, we obtain the existence and uniqueness theorem for solutions of Caputo type fractional stochastic delay differential systems (FSDDSs) with Poisson jumps by utilizing delayed perturbation of Mittag-Leffler function. Moreover, by using Burkholder-Davis-Gundy's inequality, Doob's martingale inequality and Holder inequality, we prove that the solution of the averaged FSDDSs converges to that of the standard FSDDSs in the sense of Lp. Some known results in the literature are extended.

An analytical method was established by HPLC-DAD-ELSD with C18-NH2 column tandem for the simultaneous determination of hydrophobic components atractylenolide I, II, III, atractylone and hydrophilic compounds glucose, fructose and sucrose in the dried rhizome of Atractylodes macrocephala Koidz (a natural raw material for health foods, Bai-Zhu aka. in Chinese). The method combines different separation capabilities of reversed-phase liquid chromatography and hydrophilic interaction liquid chromatography, can provide a new choice for the simultaneous determination of hydrophilic and hydrophobic compounds in traditional Chinese medicines and health foods. It provided a reference method for the quality control of Bai-Zhu. The results showed that the linear correlation coefficients of the established column tandem chromatographic method were all greater than 0.9990, the relative standard deviation was 0.1%-2.8%, and the average recovery was 96.7%-103.1%. The contents of atractylenolide I, II, III, atractylone, fructose, glucose, and sucrose in 17 batches of Baizhu were 172.3-759.8 μg/g, 201.4-612.8 μg/g, 160.3-534.2 μg/g, 541.4-8723.1 μg/g, 6.9-89.7 mg/g, 0.7-7.9 mg/g, and 1.2-21.0 mg/g, respectively.

Declining agricultural productivity caused by soil salinization are becoming global dilemmas in recent years. Biofertilizers show great potential as a sustainable and environmentally friendly fertilization strategy for soil improvement, but their effectiveness for saline soil amendment and improving plant growth under saline stress is not well understood. Assess the effectiveness of biofertilizers in improving saline soils and enhancing crop growth under saline stress, as well as investigate its related potential mechanisms. Changes in soil physico-chemical properties, plant physiological parameters and soil microbial communities were analyzed through pot experiments. The results showed that the application of biofertilizer reduced total soluble salts (TSS) in soil by 30.8% and increased the Brassica rapa L. biomass by 8.4 times. Biofertilizer application increased soil organic matter (SOM), total nitrogen (TN) and available phosphorus (AP). Biofertilizer applications also increased the SOD, CAT, chl.a, chl.b, total soluble sugars, and Proline content. Biofertilizers present plant growth promotion and potential pathogenic fungi reduction by increasing the abundance of Bacillus and Planococcus and decreasing the abundance of Mortierella and Aspergillus. Overall, the results of this study demonstrated the excellent efficacy of biofertilizers in improving saline soils, and the application of biofertilizer strategies will greatly promote agricultural production.

To facilitate the computation of the uniaxial compressive strength value of the cemented paste backfill under the condition of high sand-cement ratio, and to analyze the size effect of the cemented paste backfill with high sand-cement ratio under varied aspect ratios, the cemented paste backfill specimens with sand-cement ratios of 8:1-24:1 and aspect ratios of 0.5, 1, and 2 were prepared. Through response surface experiments and finite element analysis, the influence of three aspect ratios on the cemented paste backfill strength was explored, and the failure characteristics and size effect mechanisms of cemented paste backfill with various aspect ratios were analyzed. The model of strength conversion between cemented paste backfill with different aspect ratios was established. The results show that the compressive strength of the cemented paste backfill decreases with the increase of the aspect ratio under the same mass concentration and sand-cement ratio. When the aspect ratio is 0.5 and 1, the splitting failure is the main factor; when the aspect ratio is 2, the shearing failure is the main factor. The three-dimensional stress caused by the end effect of the cemented paste backfill is the main reason for the high strength when the aspect ratio is 0.5. Due to the one-dimensional stress zone generated in the middle of the cemented paste backfill with an aspect ratio of 2 in the laboratory, its strength value is closer to the actual uniaxial compressive strength value of the cemented paste backfill. The strength values of the cemented paste backfill with aspect ratios of 0.5 and 1 were higher than the actual uniaxial compressive strength values in the laboratory. The rationality of the theoretical analysis was verified by the ABAQUS analysis results. According to the experimental results, a strength conversion model between different aspect ratios is established, which can provide a reference for the design of the uniaxial compressive strength of the cemented paste backfill.

Vitamin E, a potent antioxidant, is a necessary and complex micronutrient for cows. During the transition period, vitamin E deficiency (VED) is among the highest prevalent micronutrient deficits in dairy cows. It may eventually result in oxidative stress and immunological malfunction, and it increases the risk of peripartum disorders. At present, detailed data on blood metabolites in VED cows are limited. Consequently, the purpose of this research was to examine the alterations in the serum metabolic profile of VED cows throughout the early postpartum period. Using comprehensive 1H nuclear magnetic resonance (1H NMR), the alterations in serum metabolic activities of VED cows were analyzed. In total, 28 multiparous Holstein cows were assigned according to serum α-tocopherol (α-Toc) concentrations into a normal (α-Toc ≥ 4 μg/mL, n = 14) and VED (α-Toc < 3 μg/mL, n = 14) groups at 21 days postpartum, and their blood samples were collected for biochemical and 1H NMR analyses. A t-test on independent samples as well as multivariate statistics were used to assess the findings. In comparison with normal cows, VED cows showed significantly worse body condition scores, milk yield, and dry matter intake (p < 0.05). Significantly higher levels of serum non-esterified fatty acids, aspartate aminotransferase, low-density lipoprotein, and malonaldehyde were found in VED-affected cows, as well as lesser concentrations of serum albumin, high-density lipoprotein, and total antioxidant capacity in comparison with normal cows (p < 0.01), while other vitamins and minerals concentrations showed no distinction between the groups (p > 0.05). Furthermore, 24 upregulated serum metabolites were identified under VED conditions. The metabolomics pathway analysis of these metabolites demonstrated that a global metabolic response to VED in cows was represented by changes in 11 metabolic pathways, comprising energy, carbohydrate, and amino acid metabolism. These outcomes suggest that VED cows were more likely to experience a negative energy balance characterized by alterations of common systemic metabolic processes and develop oxidative stress, inflammation, and ultimately liver injury. This study provides the first evidence of metabolic changes in cows with VED.

We analyzed the plant-litter-soil continuum to investigate the carbon and nitrogen distribution and ecological stoichiometry of an evergreen broad-leaved forest at Dagangshan Mountain, Jiangxi. The results showed that the average C and N contents and C:N ratios in the leaves and fine roots among 6 different tree species were 401.87g/kg, 21.41g/kg, 19.27 and 348.64g/kg, 15.73g/kg, 23.97, respectively; the average C and N contents and C:N ratios were 323.06 g/kg, 12.76 g/kg, 25.58 respectively in leaf litter, and 16.40 g/kg, 1.09 g/kg, 16.27 respectively for soil. In contrast with the C content, the total N content of the fine roots and litter had a high coefficient of variation and a high spatial heterogeneity. We ranked the six different representative tree species according to total C and N content in leaves and fine roots. The results for each species were generally consistent with each other, showing a positive correlation relationship between total C and N content in the leaves and roots. Among them, S. discolor (Champ. ex Benth.) Muell. plants displayed high carbon and nitrogen storage capacities, and on the other hand, C. fargesii Franch., C. myrsinifolia (Blume) Oersted, A. fortunei (Hemsl.) Makino, and V. fordii (Hemsl.) Airy Shaw showed a high nitrogen transfer rate. Total soil N and C decreased with depth. Soil organic carbon (SOC), soil resistant organic carbon (ROC), total N, alkali nitrogen, NH4+-N and NO3--N contents were all also negative correlated with soil depth, but the contents of the NH4+-N and NO3--N did not change significantly; The spatial distribution of soil NO3--N was significantly heterogeneous. At 0-10 cm soil depth, SOC was positively correlated with alkaline nitrogen, and at 10-20 cm soil depth, SOC was significantly positively correlated with total N. In general, when soil carbon was abundant, nitrogen supply capacity was also high.

Static voltage stability has become one of the significant risks faced by large-scale renewable energy integration. However, traditional methods for static voltage stability analysis are often overly complex. This paper constructs an equivalent impedance model for renewable energy integrated distribution power systems, proposing a static voltage analysis method for renewable energy integrated distribution power systems based on impedance model index. This method has been verified to be applicable not only to renewable energy single-infeed system but also to multi-infeed system. Furthermore, an analysis is conducted on the influence of the integration capacity, location of renewable energy, and the topology of networks on impedance model index, indicating that a higher impedance model index corresponds to greater static voltage stability margins in the system. Hence, during the planning of renewable energy integration, the plan with the highest impedance model index should be selected. Finally, the accuracy of the analysis methods and conclusions in this paper was validated based on the IEEE 14-node system.

A convenient and fast multiresidue method for the efficient identification and quantification of 72 pesticides belonging to different chemical classes in red and white grape wines have been developed. The analysis was based on gas chromatography tandem quadrupole mass spectrometric determination (GC–MS/MS). An optimization strategy involved the selection of MWCNTs amount and cleanup procedure cycle times for m-PFC was performed to achieve ideal recoveries and reduce sample matrix compounds in the final extracts. The optimized procedure obtained consistent recoveries between 70.2 and 108.8% (70.2% and 108.8% for white wine, 72.3% and 106.0% for red wine) , with relative standard deviations (RSDs) generally lower than 8.3% at three spiking levels of 0.01, 0.05 and 0.2 mg/kg. Linearity was studied in the range between 0.005 and 0.2 mg/kg using pesticide standards prepared both in pure solvent and in the presence of matrix, showing coefficients of determination (R²) higher than 0.985 for all the pesticides. To improve accuracy, matrix matched calibration curves were used for calculating the quantification results. Finally, the method was used successfully in detecting pesticide residues in commercial gape wines.

Project portfolio configuration (PPC) is an important approach to maintain the sustainable development of enterprises and achieve organizations’ strategy. However, the synergetic efficacy of PPC which determines the degree of the project's strategic objectives achieved is a fuzzy problem and hard to be measured. To solve this problem, this paper takes the data envelopment analysis (DEA) as the tool to measure the efficacy of PPC under deterministic conditions. First, a portfolio evaluation index system which takes financial indicators and non-financial indicators into consideration is developed based on the review of the literature; Second, an evaluation model based on DEA is built to reduce the number of decision making-unit with the perspective of synergetic theory; Then, a computational experiment is studied to verify the feasibility of this proposed model. The results of this computational experiment show that this model can effectively narrow scope of decision-making, improve the decision-making level and provide a reference to decide the DEA effective project portfolio decision-making unit. To our knowledge, this study is the first time to apply the notion of synergetic efficacy and DEA to the PPC domain. It is hoped that this paper may shed lights on any further study about PPC and enterprise competitiveness of sustainable development.

Fusarium stalk rot (FSR) caused by the Fusarium species complex is an economic threat to maize cultivation all over the world. We investigated the population structure and genetic diversity of Fusarium spp. obtained from five major maize-growing regions of India. The Tef-1α locus was used for phylogenetic analysis of geographically distinct isolates of Fusarium verticillioides, F. andiyazi, F. proliferatum, F. nygamai, and F. acutatum causing FSR. Geographical separation among four local populations contributed to 7.87% variance, whereas 92.12% of the variance was within popula-tions, suggesting a predominant influence of local adaptation or stochastic events like genetic drift within populations, with geographical separation playing a lesser but significant role in shaping genetic diversity. Genetic differentiation statistics between Fusarium species showed lower gene flow from haplotypes except in the population of F. acutatum and F. andiyazi having high GST values. In contrast, a high Kxy was reported, indicating elevated genetic differentiation between populations. The haplotype network analysis revealed the presence of eight distinct haplotypes which reflected pathogenic evolution and adaptive potential of Fusarium spp. The results offer a comprehensive framework for discussing the implications of genetic diversity in pathogen management and the evolutionary dynamics of the Fusarium spp. causing FSR of maize in the Indian subcontinent.

Construction using earth materials demonstrates ecological sustainability using locally sourced natural materials and environmentally friendly demolition methods. In this study, the environmental impact of adding cement to soil materials for rammed-earth farmhouse construction in rural China was investigated and comparatively simulated using the One Click LCA database, focusing on the conflict between sustainability objectives and the practical aspects of cement addition. By analyzing how the addition of cement aligns with local construction practices and by addressing the debate surrounding the inclusion of cement in rammed earth construction, our objective is to provide insights into achieving a balance between the environmental impact and the pragmatic considerations of using cement in earthen building practices. Three local structure scenarios are evaluated via simulations: a cement-stabilized rammed earth wall, a fired brick wall, and a localized reinforced concrete frame structure. The quantitative environmental impacts are assessed, and the qualitative differences in adaptation, economic sustainability, and other factors are examined in the context of present-day development in rural China. The results show that the use of cement-stabilized rammed earth wall-supported structures is associated with higher embodied carbon emissions compared to structures supported by reinforced concrete frames and enclosed by brick walls; however, these emissions are lower than those for brick wall-supported structures, while effectively meeting the structural requirements. In addition, the use of cement-stabilized earth for perimeter walls simplifies material management and disposal throughout the building's life cycle, and the cost-effectiveness of cement has been found to be substantially greater than that of reinforced concrete frames and brick structures, improving economic viability and social acceptability, especially among low-income communities in rural areas.

In recent years, video anomaly detection technology , which can intelligently analyze massive video and quickly find abnormal phenomena, has attracted extensive attention with the wide application of video surveillance technology . To address the complex and diverse problem of abnormal human behavior detection in surveillance videos, a surveillance video abnormal behavior detection and localization supervised method based on the deep network model and the traditional method is proposed. Specifically, we combined AGMM and YOLACT methods to obtain more accurate foreground information by fusing the foreground maps extracted by each technique. To further improve the accuracy , we use the PWC-Net technique to extract features of the foreground images and input them into an anomaly classification model for classification. The proposed method effectively detects and locates the abnormal behavior in the monitoring scene. In addition to the aforementioned methods, this paper also employs YOLOV5 and DeepSORT networks for object detection and tracking in the video, which allows us to track the detected objects for better understanding of the scene in the video. Experiments on the UCSD benchmark dataset and the comparison with state-of-the-art schemes prove the advantages of our method.

In the paper, the authors survey integral representations of the Catalan numbers and the Catalan–Qi function, discuss equivalent relations between these integral representations, supply alternative and new proofs of several integral representations, collect applications of some integral representations, and present sums of several power series whose coefficients involve the Catalan numbers.

Individuals are pupils of society, and students represent individuals within the societal context. It is the noble aspiration of every educator to cultivate students with well-rounded personalities for the benefit of society. School curricula are instrumental in shaping the children who will, in turn, shape the future of society, and it is posited that students with well-rounded personalities are invariably those who embody love. The challenge lies in how to enable children to possess, retain, extend, refine, and be filled with love—a task necessitating the collaborative and synergetic efforts of both the educational and social systems to achieve a societal milestone. Pedagogy of love focuses on nurturing the capacity for love within students, who, through self-awareness of their indoctrination in love, transform techniques of self-love into capabilities of love for others. This process continuously generates the energy of love within social relations, thereby fostering social production, improving the relations of production, and enhancing the creative capacities, vitality, and welfare of a socialist society's wealth and capital accumulation.

This article mainly proposes the point of view that financial literacy curriculum aims to make kinds of people, to make people with financial creativity of resource integration thinking and continuous ‘to conscience’ of morality, which is cultivate a way of thinking that can maximize benefits through the use of resource integration and constantly ‘to conscience’ to achieve goals for participants in financial structures with balanced interests. In this sense, this article argues that financial literacy is to make kinds of people with a financial mindset and constantly strengthen ‘to conscience’ through uniting of knowledge and action to achieve human well-being and benign operation of society. In this sense, this article attempts to determine what is really taught in financial literacy education in terms of curriculum theory. That is to improve creativity by cultivating financial thinking with constant ‘to conscience’. The views of this paper provide a new way of thinking about financial literacy education assessment. This changes the evaluation criteria of financial literacy education from the result-oriented of wealth growth to the process-oriented of financial creativity growth, trying to move the criticism of financial literacy education curriculum and evaluation from controversy to unity.

We suppose that a Cooper pair (CP) will experience a damping force exerted by the condensed matter. A Langevin equation of a CP in two dimensional condensed matter is established. Following a method similar to Nelson's stochastic mechanics, generalized Schr\"{o}dinger equation of a CP in condensed matter is derived. If the CPs move with a constant velocity, then the corresponding direct current (DC) electrical conductivity can be calculated. Therefore, a Drude like formula of resistivity of CPs is derived. We suppose that the damping coefficient of CPs in two dimensional cuprate superconductors is a linear function of temperature. Then the resistivity and scattering rate of CPs turn out to be also linear-in-temperature. The origin of linear-in-temperature resistivity and Planckian dissipation in cuprate superconductors may be the linear temperature dependence of the damping coefficient of CPs.

In the paper, the authors find two explicit formulas and recover a recursive formula for the generalized Motzkin numbers. Consequently, the authors deduce two explicit formulas and a recursive formula for the Motzkin numbers, the Catalan numbers, and the restricted hexagonal numbers respectively.

In this study, we investigate the behavior of randomly moving particles with a defined average energy, focusing on their biased motion around a specific point. These particles' velocity magnitudes follow a Maxwell distribution with a specific scale parameter. Our analysis derives the stochastic rotation rules for these particles and introduces the Ito equation conditions for biased stochastic rotation at a given curl value. We also consider the special relativistic-like effects in this context. The findings are validated through a representative example.

Benzimidazole fungicides are a class of highly effective, low-toxicity, systemic broad-spectrum fungicides developed in the 1960s and 1970s, based on the fungicidal activity of the benzimidazole ring structure. They exhibit biological activities including anticancer, antibacterial, and antiparasitic effects. Due to their particularly outstanding antibacterial properties, they are widely used in agriculture to prevent and control various plant diseases caused by fungi. The main products of benzimidazole fungicides include benomyl, carbendazim, thiabendazole, albendazole, thiophanate, thiophanate-methyl, fuberidazole, carbamic acid, and carbendazim salicylate. This article mainly reviews the physicochemical properties, toxicological properties, and disease control efficacy, and pesticide residue and detection technologies of the aforementioned nine benzimidazole fungicides and their main metabolite (2-aminobenzimidazole). On this basis, a brief outlook on the future research directions of benzimidazole fungicides is presented.

In the paper, the authors establish two identities to express the generating function of the Chebyshev polynomials of the second kind and its higher order derivatives in terms of the generating function and its derivatives each other, deduce an explicit formula and an identities for the Chebyshev polynomials of the second kind, derive the inverse of an integer, unit, and lower triangular matrix, present several identities of the Catalan numbers, and give some remarks on the closely related results including connections of the Catalan numbers respectively with the Chebyshev polynomials, the central Delannoy numbers, and the Fibonacci polynomials.

CNN-based methods have dominated the field of aerial scene classification for the past few years. While achieving remarkable success, CNN-based methods suffer from excessive parameters and notoriously rely on large amounts of training data. In this work, we introduce few-shot learning to the aerial scene classification problem. Few-shot learning aims to learn a model on base-set that can quickly adapt to unseen categories in novel-set, using only a few labeled samples. To this end, we proposed a meta-learning method for few-shot classification of aerial scene images. First, we train a feature extractor on all base categories to learn a representation of inputs. Then in the meta-training stage, the classifier is optimized in the metric space by cosine distance with a learnable scale parameter. At last, in the meta-testing stage, the query sample in the unseen category is predicted by the adapted classifier given a few support samples. We conduct extensive experiments on two challenging datasets: NWPU-RESISC45 and RSD46-WHU. The experimental results show that our method yields state-of-the-art performance. Furthermore, several ablation experiments are conducted to investigate the effects of dataset scale, the impact of different metrics and the number of support shots; the experiment results confirm that our model is specifically effective in few-shot settings.

Regional Climatic Comfort Index (CCI) deteriorated significantly due to the climate change and anthropogenic interference. Knowledge regarding the long-term temporal dynamics of CCI in typical regions should be strengthened. In this study, we analyze the temporal and spatial evolution of CCI from 1969 to 2018 in Guangdong Province, based on meteorological indicators, including heat, humidity, wind and cloth loading etc.. Additionally, the population exposure to climate unconformity was examined since 1990 with the help of population data. Our study found that: (1) the warming and humidifying of the summer climate served as the main driving force for the continuous deterioration of CCI, with the comfortable days decreased by 1.06d/10a and the extremely muggy days increased by 2.83d/10a; (2) spatially, the lowest climate comfortability concentrated in southwestern Guangdong with more than 50 uncomfortable days each year, while the climate comfortability in northeastern Guangdong tends to deteriorated whit higher rate, which can reach as high as 6d/10a; (3) in summer, the population exposure to uncomfortable climate highly centralized in the Pearl River Delta, Shantou, Jieyang, and the surrounding areas, and both area and population exposure showed increasing trends. Particularly, Shenzhen held the highest growth rate of population exposure with an increase rate of 2.94 million/10a; (4) although the discomfort distribution and deterioration rate vary across the province, the spatial heterogeneity of comfortability is diminishing in Guangdong Province. This study will provide scientific reference for regional urban planning, thermal environment improvement, local resident health risk analysis, and key strategy implementation, etc.

This paper addresses a new micromechanical model to predict biaxial tensile moduli of plain weave fabric (PWF) composites by considering the interaction between the orthogonal interlacing strands. The two orthogonal yarns in micromechanical unit cell (UC) were idealized as the curved beams with a path depicted by using sinusoidal shape functions. The biaxial tensile moduli of PWF composites were derived by means of the minimum total complementary potential energy principle founded on micromechanics. The biaxial tensile tests were respectively conducted on the RTM-made EW220/5284 PWF composites at five biaxial loading ratios of 0, 1, 2, 3 and ∞ to validate the new model. The predictions from the new model were compared with experimental data and good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed model. Using the new model, the biaxial tensile moduli of plain weave fabric (PWF) composites could be predicted based only on the properties of basic woven fabric.

Under the dual erosion conditions of the dry-wet cycle, which is caused by the high chloride salt concentrations in mine water and fluctuations in mine water level, cemented paste backfill (CPB) suffers serious damage and deterioration. To discuss the mechanical properties and permeability characteristics of CPB under erosion, this study designs an immersion experiment for CPB under chloride salt and dry-wet cycle conditions. Through a uniaxial compressive strength (UCS) test, the change law for the mechanical parameters of the CPB was explored, strength constitutive equation of the CPB was constructed, and the process of deterioration of the CPB was analyzed. Through the penetration test, the diffusion characteristics of packing under chloride salt and dry-wet cycle conditions were explored. The results demonstrated that the strength and elastic modulus of the CPB first increased and then decreased rapidly, with maximum decrease rates of 32.2% and 38.2%, respectively. The CPB structure presents an initial non-damage stage, initial damage stage, damage development stage, damage destruction, and residual damage stage. The chloride ion penetration depth gradually increased with an increase in the number of dry-wet cycles, with a maximum diffusion depth of 20.5 mm. The maximum apparent diffusion coefficient of chloride ion was 18.99×10-10m2/s, and the maximum concentration was 0.303 mol/L. Under the double erosion conditions due to chloride salt and dry-wet cycle, the CPB structure is seriously damaged.

Iron tailings are solid waste generated after the mining of iron mines, which have caused serious damage to the surrounding ecology and environment and have attracted widespread attention. By analyzing the formation causes, main components, and environmental effect mechanisms of iron tailings, the article systematically elaborates on the degree and mechanism of the harm of iron tailings to water bodies, atmosphere, soil, and ecosystems, and evaluates its impact on human health and sustainable development of society. On this basis, specific prevention and control measures have been proposed to reduce iron tailings emissions, realize resource recycling, and restore ecosystems. Research shows that iron tailings containing heavy metals can widely pollute the environment through dissolution and migration, and have significant biological toxicity effects. The research results can provide a theoretical reference for decision-making departments to formulate scientific and reasonable iron tailings disposal and ecological protection policies. It is recommended to strengthen specific research on the infiltration of toxic and harmful components in tailings in the future, and develop efficient and stable solidification technology, and vegetation-microbial joint restoration models to further reduce the ecological and environmental risks of iron tailings.

Distributed/semi-distributed models are considered to be sensitive to the spatial resolution of the data input. In this paper, we take a small catchment in high urbanized Yangtze River Delta, Qinhuai catchment as study area, to analyze the impact of spatial resolution of precipitation and the potential evapotranspiration (PET) on the long-term runoff and flood runoff process. The data source includes the TRMM precipitation data, FEWS download PET data, and the interpolated metrological station data. GIS/RS technique was used to collect and pre-process the geographical, precipitation and PET series, which were then served as the input of CREST (Coupled Routing and Excess Storage) model to simulate the runoff process. The results clearly showed that, the CREST model is applicable to the Qinhuai catchment; the spatial resolution of precipitation had strong influence on the modelled runoff results and the metrological precipitation data cannot be substituted by the TRMM data in small catchment; the CREST model was not sensitive to the spatial resolution of the PET data, while the estimation fourmula of the PET data was correlated with the model quality. This paper focused on the small urbanized catchment, suggesting the influential explanatory variables for the model performance, and providing reliable reference for the study in similar area.

In the paper, the authors establish two identities, which can be regarded as nonlinear differential equations, for the generating function of Eulerian polynomials, find two identities for the Stirling numbers of the second kind, and present two identities for Eulerian polynomials and higher order Eulerian polynomials, pose two open problems about summability of two finite sums involving the Stirling numbers of the second kind. Some of these conclusions meaningfully and significantly simplify several known results.

Cotton fiber, a crucial and sustainable resource for global textile production, undergoes a complex five-stage developmental process, encompassing initiation, elongation, transition, secondary cell wall biosynthesis, and maturation. These elongated single-cell fibers originate from the outer ovule epidermis. The development of cotton fibers involves intricate changes in gene expression and physiological processes, resulting in a nearly pure cellulose product vital for the global cotton industry. Decoding genes associated with fiber development enhances our understanding of cotton fiber mechanisms and facilitates the cultivation of varieties with enhanced quality. In recent decades, advanced omics approaches, including genomics, transcriptomics, and proteomics, have played a pivotal role in identifying genes and gene products linked to cotton fiber development, including the MYB transcription factor family which coordinates cotton fiber development. Molecular studies have revealed transcription factors like MYB, WRKY, Homeodomain Leucine Zipper (HD-ZIP) and basic Helix-Loop-Helix (bHLH) influencing fiber initiation and elongation. The intricate interplay of phytohormones like auxin, gibberellic acid (GA), brassinosteroid (BR), jasmonic acid (JA), ethylene, abscisic acid (ABA), and cytokinin is explored, providing a comprehensive perspective on shaping cotton fibers. Numerous candidate genes and cellular processes affecting various aspects of fiber development hold promise for genetic engineering or marker-assisted breeding to improve fiber quality. This review presents a comprehensive overview of key achievements in cotton molecular biology, with a specific emphasis on recent advancements in understanding transcription factors and phytohormones involved in cotton fiber initiation and elongation.

Civic participation is of great significance to urban management decision-making. In order to facilitate citizens to participate in city management decision-making, this paper proposes a large-scale group decision-making (LSGDM) method based on multi-granular probabilistic linguistic preference relations (MG-PLPRs). First, each decision maker selects a language terms set from the multi-granularity language terms set to represent individual preference relations and the MG-PLPRs are obtained by statistical calculation to represent sub-group’s preferences information. Then, an optimization model based on the expected consistency of PLPR and consensus measure of groups is established to achieving consensus reaching processes, which can ensure satisfactory individual consistency and group consensus. Finally, the validity and applicability of the proposed method is verified by a case of a city "shared garden" site selection with the participation of citizens.

In typical Cobalt-chromium (CoCr) alloys powders, aluminum oxide (Al₂O₃) powder can be added. In the present study, we successfully prepared alloyed samples of various powder ratios by laser cladding, and analyzed their microstructure and carbide structural characteristics, including microhardness, biological properties, morphology (using scanning electron microscopy), and crystal structure (using X-ray powder diffraction). Elemental distribution was also determined by energy-dispersive X-ray spectral analysis. The results showed that Al₂O₃ addition caused the alloy to change from slender columnar crystals to columnar grains similar, to equiaxed grains. In addition, Al₂O₃ agglomeration zones appeared, and carbide structures were altered. The mechanism of the observed performance changes was also analyzed.

8-Hydroxydeoxyguanosine (8-OHdG) was the most widely used oxidative stress biomarker of the free radical-induced oxidative damage product of DNA, which may allow a premature assessment of various diseases. This paper designed a label-free, portable biosensor device to direct detect 8-OHdG by plasma coupled electrochemistry on transparent and conductive indium tin oxide (ITO) electrode. We reported a flexible printed ITO electrode made from particle-free silver and carbon inks. After inkjet printing, the working electrode was sequentially assembled by gold nanotriangles (AuNTAs) and platinum nanoparticles (PtNPs). This nanomaterial-modified portable biosensor showed excellent electrochemical performance for 8-OHdG detection from 10 μg/mL to 100 μg/mL by our self-developed constant voltage source integrated circuit system. This work demonstrated a portable biosensor for simultaneously integrating nanostructure, electroconductivity, and biocompatibility to construct advanced biosensors for oxidative damage biomarkers. The proposed nanomaterial modified ITO-based electrochemical portable device was a potential biosensor to approach 8-OHdG point-of-care testing (POCT) in various biological fluid samples, such as saliva and urine samples.

In recent years, the Chinese government pays more and more attention to agricultural development and ecological protection. While improving the cultivated land green use efficiency(CLGUE) is the key to promote the sustainable development of agriculture. This study aims to study the current situation and influencing factors of agricultural production from the perspective of green utilization efficiency of cultivated land. It takes 39 cities in the upper, middle and lower reaches of the Yangtze River basin in China as an example. The CLGUE values in those 39 cities from 2011 to 2020 were specifically measured, using the Super-SBM model, kernel density estimation and geographic detector method. Their temporal and spatial heterogeneity was described, and the influencing factors were detected at both single and interactive levels. The results showed that: （1）From 2011 to 2020, the green utilization efficiency value of cultivated land in the Yangtze River Basin showed an upward trend on the whole; （2）There is a clear spatial heterogeneity the CLGUE values in the Yangtze River Basin cities, as shown by: downstream region > midstream region > upstream region; (3) Cultivated land resource endowment, socioeconomic development, and agricultural production technology are important factors affecting the variability of CLGUE values. However, there are some differences in the degree and direction of influence of different influencing factors on different sample subgroups.

The geographical environment, food culture, and dietary habits are substantially different between the southern and northern regions in China. We investigated the associations with dietary patterns and metabolic syndrome between Chinese adult from the southern and northern regions (North: 1249; South: 1849) using data from the Chinese Health and Nutrition 2009 survey. Respectively, four dietary patterns were identified by factor analysis in the two regions. Each dietary pattern of factor score was calculated for three groups by tertile (T1<T2<T3). In the northern region, the association between the Alcohol and Western pattern and the risk of abdominal obesity (OR: 1.31; 95%:1.01, 1.68), hypertriglyceridemia (OR: 1.35; 95%:1.05, 1.74), high fasting blood glucose (OR: 1.37; 95%: 1.05, 1.80), and hypertension (OR: 1.55; 95%: 1.45, 1.99) was increased. In the southern region, the Convenience Food pattern was positively associated with hypertriglyceridemia (OR: 1.53; 95%: 1.03, 2.26), low HDL-cholesterol (OR: 1.96; 95%: 1.12, 3.43), and metabolic syndrome (OR: 1.79; 95%: 1.03, 3.11). The Alcohol dietary pattern was positively associated with high fasting blood glucose (OR: 1.83, 95%: 1.13, 2.97). There are some dietary pattern differences in the two regions. It is necessary to consider the factors of food culture and food intake habits in order to provide nutrition education to Chinese individuals from different regions in the future.

This study investigates the effects of Zinc (4wt.%) and severe plastic deformation on the mechanical properties of AZ61 magnesium alloy through the stir-casting process. The severe plastic deformation (equal channel angular pressing (ECAP)) has been done followed by T4 heat treatment. The microstructural examinations revealed that the addition of 4wt.%Zn enhances the uniform distribution of β-phase, contributing to a more uniformly corroded surface in corrosive environments. Additionally, dynamic recrystallization (DRX) significantly reduces the grain size of as-cast alloys after undergoing ECAP. The attained mechanical properties demonstrate that after a single ECAP pass, AZ61 + 4wt.%Zn alloy exhibits optimal yield strength (YS), ultimate compression strength (UCS), and hardness. This research highlights the promising potential of AZ61 + 4wt.%Zn alloy for enhanced mechanical and corrosion-resistant properties, offering valuable insights for applications in diverse engineering fields.

We suppose that vacuum is filled with a kind of continuously distributed matter which may be called the $\Omega(1)$ substratum, or the electromagnetic aether. Suppose that the time scale of a macroscopic observer is very large compares to the the Maxwelllian relaxation time of the $\Omega(1)$ substratum. Thus, the macroscopic observer concludes that the $\Omega(1)$ substratum behaves like a Newtonian-fluid. Inspired by H. A. Lorentz, we speculate that electric charges may be extremely small hard spherical sources or spherical sinks with finite radii. Based on the spherical source and spherical sink model of electric charges, we derive Coulomb's law of interactions between static electric charges in vacuum. Further, we derive a reduced form of the Lorentz's force law for static electric charges in vacuum.

Stem cells are undifferentiated cells which can give rise to any types of cells in our body. Hence, they have been utilized for various applications such as drug testing and disease modeling. However, for the successful of those applications, the survival and differentiation of stem cells into specialized lineages should be well controlled. Growth factors and chemical agents are the most common signals to promote the proliferation and differentiation of stem cells. However, those approaches holds several drawbacks such as the negative side effects, degradation or denaturation, and expensive. To address such limitations, nanomaterials have been recently used as a better approach for controlling stem cells behaviors. Graphene oxide is the derivative of graphene, the first 2D materials in the world. Recently, due to its extraordinary properties and great biological effects on stem cells, many scientists around the world have utilized graphene oxide to enhance the differentiation potential of stem cells. In this mini review, we highlight the key advances about the effects of graphene oxide on controlling stem cell growth and various types of stem cell differentiation. We also discuss the possible molecular mechanisms of graphene oxide in controlling stem cell growth and differentiation.

In the paper, the authors present unified generalizations for the Bell numbers and polynomials, establish explicit formulas and inversion formulas for these generalizations in terms of the Stirling numbers of the first and second kinds with the help of the Faà di Bruno formula, properties of the Bell polynomials of the second kind, and the inversion theorem connected with the Stirling numbers of the first and second kinds, construct determinantal and product inequalities for these generalizations with aid of properties of the completely monotonic functions, and derive the logarithmic convexity for the sequence of these generalizations.

Various tissue resident stem cells are receiving attention from basic scientists and clinicians as they hold certain promise for regenerative medicine. This paper is intended to clarify and facilitate the understanding, development and adoption of regenerative medicine in general and specifically of therapies based on unmodified, autologous adipose-derived regenerative cells (UA-ADRCs). To this end, results of landmark experiments on stem cells and stem cell therapy performed in the labs of the authors are summarized, the most intriguing of which are the following: (i) vascular associated mesenchymal stem cells (MSCs) can be isolated from different organs (adipose tissue, heart, skin, bone marrow and skeletal muscle) and differentiated into ectoderm, mesoderm and endoderm, providing significant support for the hypothesis of the existence of a small, ubiquitously distributed, universal vascular associated stem cell with full pluripotency; (ii) the orientation and differentiation of MSCs are driven by signals of the respective microenvironment; and (iii) these stem cells irrespective of the tissue origin exhibit full pluripotent differentiation potential without any prior genetic modification or the need for culturing. They can be obtained from a small amount of adipose tissue when using the appropriate technology for isolating the cells, and can be harvested from and re-applied to the same patient at the point of care without the need for complicated processing, manipulation, culturing, expensive equipment, or repeat interventions. These findings demonstrate the potential of UA-ADRCs for triggering the development of an entire new generation of medicine for the benefit of patients and of healthcare systems.

In this paper, the synthesis of two novel luminescent Eu3+ ion complexes [Eu(TFT)3(phen) (1) and Eu(TFT)3(bpy)•Hex (2)] based on the combination of 2-(2,2,2-trifluoroethyl)-1-tetralone (TFT), containing n-donor ligands (1,10-phenanthroline or 2,2'-Bipyridine) and Eu3+ ion is reported herein, and their structural features are discussed on the basis of X-ray crystallographic and thermal analyses. We observed that the ligands transfer energy effectively to the metal center by fluorescence, IR and UV spectrograms studies. The structures and properties of complexes 1-2 were optimized by the DFT theoretical calculation, and the calculation results were consistent with the experimental X-ray structure data and spectral analysis.

In order to cope with the limited supply of feed for global animal production, there is a pressing need to explore alternative feed resources. Orange pulp, a by-product of agriculture and industry, has shown potential to positively or neutrally impact pig productive performance when included in their diet. However, there is a lack of research on the effects of fermented navel orange pulp (FNOP) on pig growth and productive performance. This study aimed to investigate the effects of FNOP as a dry matter substitute on pig’s growth performance, carcass characteristics, meat quality, meat nutrition, and serum biochemical indicators. The experiment involved 128 finishing Tibetan pigs, divided into four feed treatment groups, with varying levels (0%, 5%, 10% and 15%) of FNOP replacing dry matter in the basal diet. The results indicated that substituting 5% to 15% FNOP had no adverse effects on pig growth performance. However, at a 15% substitution rate, there was a decrease in serum growth hormone and IGF-1 levels, along with an increase in feed-to-gain ratio. A 10% FNOP replacement notably increased the eye muscle area of pigs. Additionally, 5% and 10% FNOP substitutions reduced the drip loss of pork. The study also found that substituting 5% to 15% FNOP increased unsaturated fatty acids and umami nucleotide contents in pork, as well as raised serum total protein and uric acid (nucleotide metabolism related-product) levels. These findings suggest that moderate FNOP substitution might enhance meat quality and maintain growth and productive performance in Tibetan pigs by improving protein synthesis and nucleotide metabolism, while also reducing feed costs. The optimal substitution ratio identified was 10%.

The purpose of this study is to ascertain whether implementation difficulty can be used in slot allocation model as a new mechanism for slightly weakening grandfather right. According to which, a linear integer programming model is designed to compare and analyze displacement, implementation difficulty and priority with different weights. Test results show that the implementation difficulty can be significantly reduced without causing excessive displacement and disruption of existing priorities, by weight setting while declared capacity is cleared. In addition to this, whether the movements are listed in order of descending priority or not have great impact on displacement and implementation difficulty within slot allocation model. Capacity is surely a key factor affecting displacement and implementation difficulties. This study contributes to propose a new mechanism for slightly weakening grandfather right, which can help decision makers to upgrade slot allocation policies.

J. C. Maxwell, B. Riemann and H. Poincar$\acute{e}$ have proposed the idea that all microscopic particles are sink flows in a fluidic aether. Following this research program, a previous theory of gravitation based on a mechanical model of vacuum and a sink flow model of particles is generalized by methods of special relativistic continuum mechanics. In inertial reference frames, we construct a tensorial potential which satisfies the wave equation. Inspired by the equation of motion of a test particle, a definition of a metric tensor of a Riemannian spacetime is introduced. Applying Fock's theorem, generalized Einstein's equations in inertial systems are derived based on some assumptions. These equations reduce to Einstein's equations in case of weak field in harmonic reference frames. There exist some differences between this theory and Einstein's theory of general relativity.

Energy dissipation is one of the most important factors in choosing stepped spillways. However, few studies are about energy dissipation with different horizontal face angles. In this paper, the realizable k-ε turbulence model was used to study the flow field and energy dissipation rates of different stepped spillways with five horizontal face angles in the skimming flow regions. It shows that the free water surfaces and energy dissipation rates change with horizontal face angles and the energy dissipation rates initially decrease and then increase as the horizontal face angle increases. And the horizontal face angles cause the great changes of flow field.

Geological structures such as joints and faults in rock mass have significant influence on open pit mining. Hence, it is critical to develop a understanding of dynamic joint behaviour under blasting loading. This in turn can provide both theoretical and practical guidance to improve blasting rock fragmentation and associated bucket excavating efficiency. In this paper, delayed blasting on the highwall bench at Baiyunebo open-pit mine was used as an example, a nonlinear joint blasting model was also constructed. By simplifying the blasting wave propagation velocity, the P-wave normal incidence to the joint was obtained. The peak vibration velocity was 0.33m/s at 3.0s. The S-wave reflected by the joint interface was first reflected backward and then forward, which the peak vibration velocity was 0.027 m/s. By combining the relevant stress and displacement theories of type I and II cracks, the equipotential diagrams of the stress and displacement field with the vibration velocity of the particle were obtained. σx was positive in the direction of 0~330° and subjected to tensile stress, whereas σy was positive in the direction of 0~180° and under tensile stress. The longitudinal σy along joint was low in compressive stress distribution area and did not affect surrounding rock at the time. The stress concentration appeared in the lower right corner. Based on the continuous behavior of stress wave in joints, the asymmetry and continuous changes reflected in the whole process could not be analysed by the contour diagram. Hence, ANSYS used to analyse distribution of the stress field. The intensity of the shock wave after detonation was greater than that of the rock strength. Subsequently, the sub-layer shock wave supplemented the shock wave energy that was not enough to break the rock and induced further cracking. This was able to be visualized by the degree of color change post-processing. It was concluded that with the attenuation of the detonation wave energy, the stress exhibited a decreasing trend in this process. According to distribution of the peak effective stress, it was found that the peak value first increased to 10-12 MPa and then showed a downward trend. Overall, the results were validated against the finite element simulation and mathematical analysis.

Correlation between the category richness (CR) and morphological diversity (MD) of some communities at a local scale was found pendent, however, examination of a whole category using a large dataset are lacking. In this study, 1119 jewel species from around the world representing all existing subfamilies and 33.78% of Buprestidae genera were selected as a test group. A geometric morphometric analysis on the contour of homologous traits: pronotum and elytra was conducted to quantify morphological diversity. Correlations between MD and CR among subfamilies were found to be consistently positive with the exceptions of a pronotum genus-level test on the subfamily category. The correlation was also found to be higher at the genus-level than it on the species-level, in both pronotum and elytron measurements. Based on our analyses the hypothesis of positive correlations was expected in the genus-level test of jewel beetles but rejected in species-level test. The inconsistent correlation between morphological diversity and species richness revealed convergent morphological variation of pronotum under the similar functional diversity in Buprestidae. In addition, our test revealed variable correlation between MD and CR based on different groups and characters, which might be caused by morphological changes under coevolution with different ecological factors.

By using the particle swarm optimization algorithm for crystal structure prediction, we reveal a newly orthorhombic Cmcm structure of HfB4, which is more energetically superior to the previously proposed YB4-, ReP4-, FeB4-, CrB4-, and MnB4-type structures in the considered pressure range. The phonon dispersion and elastic constants calculations confirm that the new phase is dynamically and mechanically stable. The calculated large shear modulus (240 GPa) and high hardness (45.7 GPa) imply that the predicted Cmcm-HfB4 is a potential superhard material. Meanwhile, the directional dependences of the Young's modulus, bulk modulus, and shear modulus for HfB4 are systematically investigated. Further analyses of the density of states and electronic localization function indicate that the strong B-B and B-Hf covalent bonds greatly contribute to its high hardness and stability.

In order to shorten the detection time and improve the average precision on embedded devices, A lightweight and high accuracy model is proposed for passion fruit in complex environments (backlight, occlusion, overlap, sunny, cloudy, rainy). Firstly, replacing the backbone network of YOLOv5 with a lightweight GhostNet model reduces the number of parameters and computation while improving detection speed. Secondly, a new feature branch is added to the GhostNet network, and the feature fusion layer in the neck network is reconstructed to effectively combine the lower-level and higher-level features, which not only improves the accuracy of the model but also maintains its lightweight. Finally, the knowledge distillation methods are used to transfer the knowledge from the more capable teacher model to the less capable student model, which significantly improving the detection accuracy. The improved model is denoted as G-YOLO-NK. The average accuracy of the G-YOLO-NK network is 96.00%, which is 1.00% higher than the original YOLOv5s model. Furthermore, the improved model size is 7.14MB, reduced to half of the original model, and the real-time detection frame rate is 11.25 FPS on the Jetson Nano. Compared to the state-of-the-art model, the proposed model outperforms them in terms of average precision and detection performance. The present work provides an effective model for real-time detection of passion fruits in complex orchard scenes, which can provide valuable technical support for the development of orchard picking robots and greatly improve the intelligence level of orchards.

Accurate evaluation of health status of lithium-ion batteries must be deemed as of great significance, insofar as utility and safety of batteries are of concern. Lithium plating, in particular, is notoriously known to be a chemical reaction that can cause deterioration in, or even fatal hazards to, the health of lithium-ion batteries. Electrochemical impedance spectroscopy (EIS), which has distinct advantages such as fast or non-destructive over its competitors, suffices in detecting lithium plating and thus has been attracting increasing attention in the field of battery management, but its ability of assessing quantitatively the degree of lithium plating remains largely unexplored hitherto. On this point, this work seeks to narrow that gap, by proposing an EIS-based method that can quantify the degree of lithium plating. The core conception is to eventually circumvent the reliance on state-of-health measurement, and use instead the impedance spectrum, to acquire an estimate on battery capacity loss. To do so, the effects of solid electrolyte interphase formation and lithium plating on battery capacity must be first decoupled, so that the mass of lithium plating can be quantified. Then, based on an impedance spectrum measurement, the parameters of the fractional equivalent circuit model (ECM) of the battery can be identified. These fractional ECM parameters are received as inputs by an artificial neural network, which is tasked to establish a correspondence between the model parameters and the mass of lithium plating. The empirical part of the work revolves around the data collected from an aging experiment, and the validity of the proposed method is truthfully attested by dismantling the batteries, which is otherwise not needed during the actual uptake of the method.

(1) Background: The analysis of athletic performance has always aroused great interest from sport scientist. This study utilized machine learning methods to build predictive models using a comprehensive CrossFit (CF) dataset, aiming to reveal valuable insights into the factors influencing performance and emerging trends.; (2) Methods: The study used Random Forest (RF) and Multiple Linear Regression (MLR) models to predict performance in four key weightlifting exercises within CF: clean &amp; jerk, snatch, back squat, and deadlift. Performance was evaluated using R-squared (R2) values and Mean Squared Error (MSE). Feature importance analysis was conducted using RF, XGBoost, and AdaBoost models.; (3) Results: The RF model excelled in deadlift performance prediction (R2 = 0.80), while the MLR model demonstrated remarkable accuracy in clean &amp; jerk (R2 = 0.93). Across exercises, clean &amp; jerk consistently emerged as a crucial predictor. The feature importance analysis revealed intricate relationships among exercises, with gender significantly impacting deadlift performance.; (4) Conclusions: This research advances our understanding of performance prediction in CF through machine learning techniques. It provides actionable insights for practitioners, optimize performance, and demonstrates the potential for future advancements in data-driven sports analytics.

Inspired by Dirac's large number hypothesis (LNH), Zeldovich proposed a relation between the cosmological constant (CC), the mass of a proton, the Planck constant and Newton's gravitational constant. Zeldovich's formula suggests that the substance which is responsible for CC may interact with elementary particles. Since Newton's gravitational constant and the Planck constant appear in Zeldovich's formula, these interactions may be related to gravitational phenomena and quantum phenomena. Following this clue, we propose a liquid droplet model of electron. Applying the Laplace's equation, Zeldovich's formula of CC is derived. Weinberg proposes a relation between the mass of a pion, the Planck constant, the Hubble constant, Newton's gravitational constant and the velocity of light in vacuum when discussing cosmological models with a varying constant of gravitation. Weinberg pointed out that this relation may not merely be regarded as a meaningless random combinations of these fundamental constants in physics. The Weinberg's relation is derived based on the critical mass density formula in the Friedmann model of the universe and Zeldovich's formula.

Cu-Sn shape-memory microwires were fabricated by a glass-coated melt spinning method. Effects of Sn content on the microstructure and mechanical property of microwires were investigated. The phase transforms from martensite to austenite with Sn content increasing from 14.0 atomic percent (at.%) to 16.5 at.%, and highly ordered intermetallic phase, δ, formed with higher Sn content. The fracture stress, σf, and the critical stress for martensitic transformation, σMs, increases with Sn content increasing. The mechanical property as well as superelasticity were improved greatly by high cooling rate of the glass-coated melt spinning method.

Harsh parenting could be regarded as a harsh form of behavior, feelings and attitude towards children in the process of parenting. According to the theory of intergenerational transmission of violence, harsh parenting is an important factor affecting children's aggressive behavior, but the theory does not clarify the specific action path between the harsh parenting and aggressive behavior. In order to reveal the relationship between harsh parenting and aggressive behavior of juvenile delinquents, 604 male juvenile delinquents (N=604, Mage=16.57 years, SD=0.612 years) were investigated using Harsh Parenting Questionnaire, Buss-Perry Aggression Questionnaire, Multidimensional Peer-Victimization Scale, and the Word Sentence Association Paradigm for Hostility in Chinese version. Analysis using structural equation modeling procedures showed that (a) all variables were positively associated with each others; (b) the partial indirect effect of harsh parenting on aggressive behaviors was realized through the mediator of peer victimization and hostile attribution bias independently, (c) as well as the partial indirect effect through the mediator of peer victimization and hostile attribution bias sequentially. The results suggested that harsh parenting can explain the high aggressive behavior of male juvenile delinquents. Moreover, harsh parenting may also lead to the formation of hostile attribution bias by increasing the risk of peer victimization, and ultimately lead to the formation of highly aggressive behaviors.

Earth observation satellites can capture images of specific areas in Earth's orbit based on user requirements. Despite the high demand for satellite imagery, satellites remain a scarce resource. When there are many observation tasks that are large and dense, they may interfere with each other due to satellite mobility. To address this issue, a multi-satellite scheduling algorithm based on a task merging mechanism has been proposed. This paper proposes a two-stage approach to the problem: task merging phase and merging task scheduling phase. The task merging phase introduces two methods based on Mean Shift and Complete Graph to generate the merging task set. In the merging task scheduling phase, a multi-satellite scheduling algorithm based on merging tasks is employed to solve the problem. Finally, certain measurement experiments suggest the effectiveness of the algorithm.

The Physics-Informed Neural Networks (PINNs) improve the efficiency of data utilization by combining physical principles with neural network algorithms and ensure that the predictions are consistent and stable with the physical laws. PINNs opens up a new approach to address inverse problems in fluid mechanics. Based on the single-relaxation-time lattice Boltzmann method (SRT-LBM) with the Bhatnagar-Gross-Krook (BGK) collision operator, the PINN-SRT-LBM model is proposed in this paper for solving the inverse problem in fluid mechanics. The PINN-SRT-LBM model consists of three components. The first component involves a deep neural network that predicts the equilibrium control equations in different discrete velocity directions within SRT-LBM. The second component employs another deep neural network to predict non-equilibrium control equations, enabling inference of the fluid's non-equilibrium characteristics. The third component, a physics informed function translates the outputs of the first two networks into physical infor-mation. By minimizing the residuals of the physical partial differential equations (PDEs), the physics informed function infers relevant macroscopic quantities of the flow. The model evolves two sub-models applicable to different dimensions, named PINN-SRT-LBM-I and PINN-SRT-LBM-II models according to the construction of the physical informed function. The innovation of this work is the introduction of SRT-LBM and discrete velocity models as physical drivers into the neural network through the interpretation function. Therefore, PINN-SRT-LBM allows the neural network to handle inverse problems of various dimensions and focus on problem-specific solving. Experimental results confirm the accurate prediction of flow infor-mation at different Reynolds numbers within the computational domain. Relying on the PINN-SRT-LBM models, inverse problems in fluid mechanics can be solved efficiently.

The current regeneration mode of public space in the old city of Guangzhou is ineffective, thus necessitating supplementation with a more systematic methodology. The “plug-in design” targets sustainable regeneration while preserving the overall urban texture and context, i.e., has little impact on the spatial qualities of the old city. The ultimate goal is to activate the public space of the old city of Guangzhou point-to-area through the insertion of various plug-ins. In this study, the methodology is applied to Xudi Gaodi Street, the core area of the old city of Guangzhou, to explore its effects on sustainability. The internal public space is isolated and supplied with rigid and flexible plug-ins from multiple dimensions, which not only improves the spatial environment but also injects new urban formats. This work provides a specific solution for regeneration in Guangzhou’s old city while enhancing empirical knowledge of the plug-in design to support urban regeneration theory and further practical development.

As the largest energy consumer and carbon emitter, China has made substantial efforts to improve energy efficiency for decrease energy consumption, while the energy rebound effect determines its effectiveness. The embodied energy consumption of construction projects accounted for nearly one-sixth of the total economy's energy consumption in China. This paper is based on the logical relationship among capital input, technological progress, economic growth, and energy consumption, adapting an alternative estimation model to estimate the energy rebound effect for the construction industry in China for the first time. Empirical results in our paper reveal that the energy rebound effect for the construction industry in China is about 59.5% for the period of 1990–2014. The results indicate that the energy rebound effect does exist in China’s construction industry and it presented a fluctuating declining trend. This implies that half of the energy savings by technological progress is achieved. In addition, China’s government should implement proper energy pricing reforms and energy taxes to promote the sustainable development of China’s construction industry.

The digital economy (DE) has become a major force driving the optimization and upgrading of industrial structures (ISOU), and research on the driving mechanism has yet to be verified. To this end, the driving influence of DE on the ISOU is targeted, and the role played by economic resilience (ER) and innovation is explored. Based on the panel data of 31 provinces in China from 2011 to 2020, the driving influence of the DE on the ISOU is analyzed using a two-way fixed-effects model. The empirical study finds that the DE presents a positive driving effect on both industrial structure advancement and rationalization, and the driving effect is still significant after the addition of control variables and the robust-type test with one period of lag; the DE presents regional differences in ISOU, with the driving effect of the DE on industrial structure advancement in the eastern region having a more significant performance than that of the central and western regions, and the driving influence on the rationalization of industrial structure in the eastern and western regions exceeds that in the central region; the impact of DE on the ISOU has a mediating role through innovation, ER has a moderating role in the process, and innovation as a partial mediator also has a threshold effect, and finally countermeasure suggestions are put forward.

Foam concrete is a highly cellularized cementitious material that undergoes extensive plastic deformation when loaded to failure. Under compression, the foam structure gets progressively crushed at a steady stress stage such that a substantial amount of energy is dissipated. Understanding foam concrete crushing behavior is of special importance for its engineering applications such as energy absorber, but the current studies are insufficient to define material properties for design of field applications. This study characterizes the crushing strength and foam modulus of samples with penetration test and resonant frequency test, respectively. A four-phase crushing behavior is observed. The yield strength and plateau strength are identified to characterize the foam crushing. Using the experimental inputs, the modulus-strength constitutive equations are then established. These findings are useful for expanding the knowledge of normal concrete to studies on foam concrete, as well as design of applications.Foam concrete is a highly cellularized cementitious material that undergoes extensive plastic deformation when loaded to failure. Under compression, the foam structure gets progressively crushed at a steady stress stage such that a substantial amount of energy is dissipated. Understanding foam concrete crushing behavior is of special importance for its engineering applications such as energy absorber, but the current studies are insufficient to define material properties for design of field applications. This study characterizes the crushing strength and foam modulus of samples with penetration test and resonant frequency test, respectively. A four-phase crushing behavior is observed. The yield strength and plateau strength are identified to characterize the foam crushing. Using the experimental inputs, the modulus-strength constitutive equations are then established. These findings are useful for expanding the knowledge of normal concrete to studies on foam concrete, as well as design of applications.

Visual-inertial integrated navigation system (VINS) has been extensively studied over the past decades to provide accurate and low-cost positioning solutions for autonomous systems. Satisfactory performance can be obtained in an ideal scenario with sufficient and static environment features. However, there are usually numerous dynamic objects in deep urban areas, and these moving objects can severely distort the feature tracking process which is fatal to the feature-based VINS. The well-known method mitigates the effects of dynamic objects is to detect the vehicles using deep neural networks and remove the features belongs to the surrounding vehicle. However, excessive exclusion of features can severely distort the geometry of feature distribution, leading to limited visual measurements. Instead of directly eliminating the features from dynamic objects, this paper proposes to adopt the visual measurement model based on the quality of feature tracking to improve the performance of VINS. Firstly, a self-tuning covariance estimation approach is proposed to model the uncertainty of each feature measurements by integrating two parts: 1) the geometry of feature distribution (GFD), 2) the quality of feature tracking. Secondly, an adaptive M-estimator is proposed to correct the measurement residual model to further mitigate the impacts of outlier measurements, such as the dynamic features. Different from the conventional M-estimator, the proposed method effectively alleviates the reliance of excessive parameterization of M-estimator. Experiments are conducted in a typical urban area of Hong Kong with numerous dynamic objects, and the results show that the proposed method could effectively mitigate the effects of dynamic objects and improved accuracy of VINS is obtained when compared with the conventional method.

The development of biosensors with high sensitivity and low-detection limits provides a new direction for medical and personal care. Graphene and graphene derivatives have been used to prepare various types of biosensors due to their excellent sensing performance (e.g. high specific surface area, extraordinary electronic properties, electron transport capabilities and ultrahigh flexibility). This perspective review focuses on graphene-based biosensors for quantitative detection of cancer related biomarkers such as DNA, miRNA, small molecules and proteins by integrating with different signal outputting approaches including fluorescent, electrochemistry, surface plasmon resonance, surface enhanced Raman scattering etc. The article also discussed their challenges and potential solutions along with future prospects.

The concept of using special electrical circuit design realize a "cold resistors", that is, an active resistor circuitry with lowered effective noise temperature, was first introduced about 80 years ago. Later on, various kinds of artificial resistors were applied in different research areas, such as gravitational wave detection, photo-amplifiers and quartz oscillators. Their proofs of concepts were experimentally proved. Unfortunately, the complete theory was not found even though several attempts had been published, sometimes with errors. In this paper, we describe a correct and complete circuit theoretical model of a cold resistor system. The results are confirmed by computer simulations. A design tools for this circuit is also shown.

This study analyzes the modeling and dynamics of a novel passive in Multi-Degree-of-Freedom (MDOF) vibration isolation platform which can achieve significant isolation effect. Symmetrical Scissor-Like structures (SLSs) are utilized in the proposed MDOF isolation platform as the supporting and isolation elastic components. Based on the mathematical modeling and theoretical analysis of the MDOF vibration isolation system with SLSs, the effect of structural parameter and joint friction on stiffness and damping properties is investigated. It is shown that due to geometric relations within the SLSs, the natural frequencies can be reduced via adjusting structural parameters of the SLS for different direction vibration isolation. Theoretical and experimental results show that the SLS isolation platform can achieve much better loading capacity and vibration isolation performance simultaneously by only using linear passive components because of the MDOF adjustable stiffness property. Therefore, with low costing and energy consumption, the proposed novel isolation platform can provide the improvement of vibration suppression in various engineering practices.

Gol'denveizer's problem of a torus has been analyzed by Audoly and Pomeau (2002) and Sun (2021). However, all of the investigations of Gol'denveizer's problem of an elastic torus have been linear. In this paper, the finite element method is used to more accurately address this problem. Furthermore, Sun (2021) cannot be solved by nonlinear analysis. We research the nonlinear mechanical properties of Gol'denveizer's problem of circular and elliptic tori, and relevant nephograms are given. We study the buckling of Gol'denveizer's problem of an elastic torus, and propose failure patterns and force-displacement curves of tori in the nonlinear range. Investigations reveal that circular tori have more rich buckling phenomena as the parameter a increases. Gol'denveizer's problem of the buckling of an elliptic torus is analyzed, and we find a new buckling phenomenon called a "skirt." As a/b increases, the collapse load of an elliptic torus of the Gol'denveizer problem is enhanced gradually.

Since the beginning of the internet era, there has been an explosion of growth in structured data (such as numbers, symbols, and labels) as well as unstructured data (including images, videos, and text). Efficient and accurate mixed query of these two types of data is a key technology to achieve high-quality information retrieval, and it is also a major challenge that needs to be solved urgently in the industry. In this study, we employ an advanced Transformer model that combines strategies and fine-tuning techniques for multi-task learning. Specifically, the model is first pre-trained on a large-scale, general-purpose dataset to learn different types of data representations and basic language comprehension skills. After that, we fine-tuned the parameters of the model to better suit these specific data processing tasks for specific application scenarios, such as image annotation, video content analysis, and structured data query. At the heart of the model is the self-attention mechanism, which allows the model to automatically emphasize the important parts and ignore irrelevant information when processing the input data. In addition, we have introduced task-specific adaptation layers that are designed to add additional processing power to the original Transformer architecture, such as a semantic analysis layer for unstructured text data and a relational extraction layer for structured data. This combination of general pre-training and task-specific fine-tuning allows the model to flexibly process and integrate information from different data sources, improving processing efficiency and accuracy. Experimental results show that the model performs well in a variety of data processing tasks, significantly improves the accuracy and efficiency of information retrieval, and verifies the strong potential and adaptability of large language models in processing mixed data types.

Floods are among the most serious natural disasters worldwide; they cause enormous crop losses every year and threaten world food security. There are many studies focused on flood impact assessments for administrative districts but fewer on postdisaster impact assessments for specific crops. Therefore, this study used remote sensing data, including the normalized difference vegetation index (NDVI), elevation data, slope data, and rainfall data, combined with crop growing season data to construct a crop flood damage assessment index (CFAI). First, an analytic hierarchy process (AHP) was used to assign weights to the impact factors; then, the weighted composite score method was used to calculate the CFAI; and finally, the impact was classified as slight, moderate, or severe based on the magnitude of the CFAI . This method was used for the Missouri River floods of 2019 in the U.S. Due to the lack of measured data, the disaster vegetation damage index (DVDI) was used to validate the results. The combined approach achieved a high degree of consistency in spatial distribution. The CFAI can respond well to the degree of crop impact after flooding, providing new ideas and reference standards for agriculture-related departments.

Employing remote sensing techniques to evaluate crop residue cover (CRC) enables rapid mapping of tillage practices over large cropland areas, which has significant practical implications for monitoring the implementation of conservation tillage practices. This research utilized Sentinel-2 MSI and Landsat-8 OLI remotely sensed data, various spectral indices were calculated and the datasets were correlated with the field-measured CRC data. Selected spectral indices, highly significantly correlated, were chosen to build a correlation model between the indices and the CRC. Considering Sentinel-2 MSI and Landsat 8 OLI remotely sensed data variations in spectral and spatial scales, the accuracy of CRC models was evaluated using R2 and RMSE values. From the results, it's evident that all six spectral indices, including STI, NDTI, SRNDR, NDI5, NDI7 and NDSVI, registered correlation coefficients with the CRC exceeded 0.3 in the study area. STI and NDTI showed a stronger correlation to CRC, with coefficients of 0.810 and 0.803, respectively. For the Landsat 8 data, the lowest correlation obtained was for NDSVI with the Landsat 8 data with a correlation coefficient of 0.358. Applying the linear regression technique, STI and NDTI obtained higher accuracy compared to other indices in the Sentinel-2 MSI data. For NDTI and STI, The R2 values were 0.650 and 0.665, respectively, while their corresponding RMSE values were 3.96% and 4.03%. The highest model accuracy was obtained for the STI and NDTI constructed from the Landsat 8 OLI data (R2 values 0.41 and 0.40; RMSE values 5.25% and 5.27%, respectively). The CRC model built using partial least squares regression (PLSR) exhibited greater precision when applied to the Sentinel-2 MSI data (R2 value 0.894; RMSE value 2.18%) in comparison to the Landsat 8 OLI data (R2 value 0.695; RMSE value 3.70%). PLSR has the potential to enhance the precision of the model. In addition, the study area shows that the estimation of the CRC is better in the one-dimensional linear regression model and the PLSR model created with the Sentinel-2 MSI optical data compared to the Landsat 8 OLI optical remotely sensed data. The validation suggests that the CRC estimation in the study area is more precise when using the model relying on Sentinel-2 satellite imagery rather than the Landsat 8 OLI imagery.

In pattern recognition domain, deep architectures are widely used nowadays and they have achieved fine grades. However, these deep architectures need special demands, especially big datasets and GPU. Aiming to gain better grades without deep networks, we propose a simplified algorithm framework using fusion features extracted from the salient areas of faces. Furthermore, the proposed algorithm has achieved a better result than some deep architectures. For extracting more effective features, this paper firstly defines the salient areas on the faces. This paper normalizes the salient areas of the same location in the faces to the same size, therefore it can gain more similar features from different subjects. LBP and HOG features are extracted from the salient areas, fusion features’ dimensions are reduced by Principal Component Analysis( PCA) and we apply softmax to classify the six basic expressions at once. This paper proposes a salient areas definitude method which uses peak expressions frames to compare with their neutral faces. This paper also proposes and applies the idea of normalizing the salient areas to align the specific areas which express the different expressions. This makes the salient areas found from different subjects have the same size. Besides, gamma correction method is firstly applied on LBP features in our algorithm framework which improves our recognition rates significantly. By applying this algorithm framework, our research has gained state-of-the-art performances on CK+ database and JAFFE database.

This study presents a comprehensive investigation of entropy generation during natural convection in a porous medium with Casson fluid. The governing equations, including the momentum, energy, and entropy balance equations, are solved numerically using finite element method. Through the analysis, various parameters affecting entropy generation are investigated, such as the Casson fluid parameter, Radiation, Prandtl number, and Rayleigh number. The results indicate that the Casson fluid parameter significantly influences the flow and heat transfer characteristics, while the Darcy number and Rayleigh number control the intensity of natural convection. Moreover, the Prandtl number determines the relative significance of heat transfer compared to viscous effects.

Solid porous materials, like zeolites, have been widely used in a variety of fields such as size and shape-selective absorption/separation and catalysis because of their porosity. But there are few liquid materials exhibit permanent porosity. Porous liquids are a novel material that combine the properties of fluidity and permanent porosity. It has potential applications in many fields such as gas separation, storage and transport. Herein, we report a novel Type 1 porous liquid prepared based on Silicalite-1. The pore size of this porous liquid was determined by positron annihilation lifetime spectroscopy (PALS), and the CO2 capacities was determined by the intelligent gravimetric analyser (IGA). The unique properties of this porous liquid can promote its application in many fields such as gas storage and transport.

In the paper, using two inversion theorems for the Stirling numbers and binomial coecients, employing properties of the Bell polynomials of the second kind, and utilizing a higher order derivative formula for the ratio of two dierentiable functions, the authors present two explicit formulas, a determinantal expression, and a recursive relation for a sequence of unnamed polynomials, derive two identities connecting the sequence of unnamed polynomials with the Bell polynomials, and recover a known identity connecting the sequence of unnamed polynomials with the Bell polynomials.

In the paper, by virtue of the Faà di Bruno formula, some properties of the Bell polynomials of the second kind, and an inversion formula for the Stirling numbers of the first and second kinds, the authors establish meaningfully and significantly two identities which simplify coefficients in a family of ordinary differential equations associated with higher order Bernoulli numbers of the second kind.

In the paper, by virtue of the Fa`a di Bruno formula, some properties of the Bell polynomials of the second kind, and the inversion formulas of binomial numbers and the Stirling numbers of the first and second kinds, the authors simplify meaningfully and significantly coefficients in two families of ordinary differential equations associated with higher order Frobenius–Euler numbers.

Extreme climates such as droughts and hot extremes, may result in marked damage to crop yields and threaten regional and global food security. Maize is a major grain crop in Liaoning Province, severely affected by drought and hot events. The objective of this study is to advance an approach to estimate the risk of crop yield reduction under the compound dry-hot events (CDHE) in Liaoning Province. Results show that the ratio of stations experiencing compound dry-hot events during the twelfth leaf and maturity stage tended to increase on the time scale. On a spatial scale, the frequency of compound dry-hot events in central Liaoning Province was relatively low during the whole and various reproductive periods of maize. In addition to the twelfth leaf, western Liaoning Province is prone to compound dry-hot events. The high-risk area for the occurrence of the compound dry-hot events in maize is Chaoyang City, located in the western part of Liaoning Province, and the cities in the low-risk area account for about 64.3% of the total number of cities in Liaoning Province, mainly in the central and northern parts of Liaoning Province. Generally, this study emphasizes focusing on the impacts of compound dry-hot events on agricultural production and provides an index to assess the risk of compound dry-hot events on maize production.

Management of Australia’s largest river system, the Murray-Darling Basin (MDB) is controversial, addressing conflicting demands from stakeholders, including irrigators, the agriculture industry, indigenous groups, and the environmental lobby. Oversight is concentrated in a single agency, the MDB Authority, but climate change and the water market have contributed to uncertainty over the Basin’s environmental sustainability. This paper reports on preliminary research in South Australia’s Riverland, one of Australia’s most important wine, citrus, nuts, and stone fruit production areas. It focuses on the Renmark Irrigation Trust (RIT), supplying water to irrigators, primarily horticulturalists. It investigates the chief risks perceived and future-plans in face of concerns over variable water flows and economic uncertainty. Using sequential mixed methods, a questionnaire survey supplied information from a sample of irrigators, covering land use, on-farm environmental actions, risks, decision making, recent and proposed changes to farm management, and attitudes to the MDB Plan and the water market. Focus groups and interviews then enabled key topics to be addressed in greater depth. The RIT’s contribution to river restoration is highlighted, with its plans for additional on-farm water stewardship investigated. There are high levels of uncertainty regarding future viability of smallholdings, including unintended consequences from the water market (e.g., increasing areas under water hungry almonds), the role of water brokers, and environmental viability of the river system linked to climate change. More optimistic voices point to increased diversity of production, resilience of the local horticultural industry, and new entrants in the form of hobby and part-time producers.

Although global life expectancy has increased over the past 20 years due to improvements in managing infectious diseases, one in five people still succumbs to infections. Humanity is tirelessly working towards developing vaccines and antimicrobial agents in response to this ongoing threat. However, pathogens continue to acquire numerous resistance mechanisms and proliferate. Meanwhile, the COVID-19 pandemic has prompted us to recognize that focusing solely on the killing strategies of immunology and microbiology in complex and multisystemic infectious diseases is insufficient for understanding survival. In essence, there is a need for a treatment approach centered on disease tolerance, capable of alleviating pathology and/or promoting physiological functions in conjunction with the existing strategies of host immune response and pathogen destruction. Against this backdrop, this narrative review comprehends and introduces microbiome therapeutics, which recently garnered attention as next-generation treatments regarding two defense strategies against infectious diseases. First, we delineate the application of existing probiotics and then the microbiome in infectious diseases. Subsequently, we expand this concept to encompass host microbiome crosstalk and present related microbiome therapeutics' current status and direction. Ultimately, the review presents a fresh perspective on understanding microbiome therapeutics in infectious diseases based on a cooperative defense system.

The testing of high-dimensional normality has been an important issue and has been intensively studied in literatures, it depends on the Variance-Covariance matrix of the sample, numerous methods have been proposed to reduce the complex of the Variance-Covariance matrix. The principle component analysis(PCA) was widely used since it can project the high-dimensional data into lower dimensional orthogonal space, and the normality of the reduced data can be evaluated by Jarque-Bera(JB) statistic on each principle direction. We propose two combined statistics, the summation and the maximum of one-way JB statistics, upon the independency of each principle direction, to test the multivariate normality of data in high dimensions. The performance of the proposed methods is illustrated by the empirical power of the simulated data of normal data and non-normal data. Two real examples show the validity of our proposed methods.

In the note, the authors find several simple and explicit forms for a family of inhomogeneous linear ordinary differential equations studied in "D. Lim, Differential equations for Daehee polynomials and their applications, J. Nonlinear Sci. Appl. 10 (2017), no. 4, 1303-1315; Available online at http://dx.doi.org/10.22436/jnsa.010.04.02".

In the paper, the authors nd a new closed expression for the Fibonacci polynomials and, consequently, for the Fibonacci numbers, in terms of a tridiagonal determinant.

In the paper, by virtue of techniques in combinatorial analysis, the authors simplify two families of nonlinear ordinary differential equations in terms of the Stirling numbers of the first kind.

Background The spread of COVID-19 continues, the mutation of SARS-COV-2 is still difficult to control, and the need for antiviral drugs to treat COVID-19 remains urgent. The use of arbidol in the treatment of COVID-19 is limited and controversial. Methods To clarify the efficacy of arbidol on COVID-19, we collected 25 cases and 178 related studies. We analyzed the treatment information of arbidol based on the obtained cases, expanded the scope of the study, and collected current studies on the treatment of COVID-19 in various databases for in-depth analysis. Results History analysis showed that arbidol was effective (76% cure rate) compared with other drugs. However, compared with other antiviral drugs or standard therapy, the arbidol group had no significant advantage in reducing the time to negative virus transformation, length of hospital stays, or improvement in CT (MD=0.22, 95%CI -0.29-0.73; MD = 0.61, 95% CI 1.46 to 2.67; RR=1.15, 95%CI 0.88-1.50); Analysis of adverse events showed no significant difference between the arbidol group and the other groups (RR=0.82, 95%CI 0.25-2.71). Conclusion Our study showed that arbidol had no significant effect on COVID-19, but showed a slight advantage in CT improvement and adverse events. Our study objectively evaluated the efficacy of arbidol in the treatment of COVID-19 and provided some guidance for arbidol in the treatment of COVID-19.

Discrete Double Hilbert Exponential sums along polynomials. This is preprint version (not peer reviewed) And we now check the proof of (ii) of Lemma 3.2 whether it is really true.

This project focuses on using machine learning classification algorithms to determine whether two people are 6 feet apart or not. Two Raspberry Pis were used simulate smart phones. RSSI values of the Bluetooth beacons transmitted between the Raspberry Pis were collected and recorded to train the classifier. The Gaussian Support Vector Machine Classifer yielded the highest testing accuracy of 79.670 and the Decision Tree Classifier yielded the highest AUC of 0.80.

The advent of deep learning has completely reshaped our world. Now, our daily life is fulfilled with many well-known applications that adopt deep learning techniques, such as self-driving cars and face recognition. Furthermore, robotics developed more forms of technology which share the same principle with face recognition, such as hand pose recognition and fingerprint recognition. Image recognition technology requires a huge database and various learning algorithms, such as convolutional neural network and recurrent neural network, that requires lots of computational power, such as CPUs and GPUs. Thus, clients could not be satisfied with the computational resource of the local machine. The cloud resource platform emerged at a historic moment. Docker containers play a significant role of microservices-based applications in the next generation. However, it could not guarantee the quality of service. From clients’ perspective, they have to balance the budget and quality of experiences (e.g. response time). The budget leans on individual business owners and the required Quality of Experience (QoE) depends on usage scenarios of different applications, for instance, an autonomous vehicle requires real-time response, but, unlocking your smartphone can tolerate delays. Plenty of on-going projects developed user-oriented optimization resource allocation to improve the quality of the service. Considering the users’ specifications, including accelerating the training process and specifying the quality of experience, this thesis proposes two differentiate containers scheduling for deep learning applications: TRADL and DQoES .

Classic Hodgkin lymphoma (cHL) is a lymphoid neoplasm composed of rare neoplastic Hodgkin and Reed-Sternberg (HRS) cells surrounded by a reactive tumor microenvironment (TME) with suppressive properties against anti-tumor immunity. TME is mainly composed of T-cells (CD4 helper, CD8 cytotoxic and regulatory), and tumor-associated macrophages (TAMs) but the impact of these cells on the natural course of the disease is not absolutely understood. TME contributes to the immune evasion of neoplastic HRS cells through production of various cytokines and/or aberrant expression of immune checkpoint molecules, in ways that have not been fully understood yet. Herein, we present a comprehensive review of findings regarding the cellular components and the molecular features of the immune TME in cHL, its correlation with treatment response and prognosis as well as the potential targeting of the TME with novel therapies. Among all cells, macrophages appear to be a most appealing target for immunomodulatory therapies, based on their functional plasticity and antitumor potency.

The human mandible's cancellous bone, which is characterized by its unique porosity and directional sensitivity to external forces, is crucial for sustaining biting stress. Traditional CAD models fail to fully represent bone's anisotropic structure and thus depend on simple isotropic assumptions. For our research, we use the latest versions of nTopology and Creo Parametric software to make biomimetic Voronoi lattice models that accurately reflect the complex geometry and mechanical properties of trabecular bone. The porosity of human cancellous bone is accurately modeled in this work using biomimetic Voronoi lattice models. The porosities range from 70% to 95%, which can be achieved by changing the pore sizes to 1.0 mm, 1.5 mm, 2.0 mm, and 2.5 mm. Finite element analysis (FEA) was used to examine the displacements, stresses, and strains acting on dental implants with a buttress thread, abutment, retaining screw, and biting load surface. The results show that the Voronoi model accurately depicts the complex anatomy of the trabecular bone in the human jaw, compared to standard solid block models. The ideal pore size for biomimetic Voronoi lattice trabecular bone models is 2 mm, taking into account both the von Mises stress distribution over the dental implant, screw retention, cortical bone, cancellous bone, and micromotions. This pore size displayed balanced performance by successfully matching natural bone's mechanical characteristics. Advanced finite element analysis (FEA) improves biomechanical understanding of how bones and implants interact by creating more accurate models of biological problems and dynamic loading situations. This makes biomechanical engineering better.

Primary urethral malignancies are rare in clinical practice and elderly female are prone to suffer. The cause of PUC is unknown and may be related to long-term chronic inflammation, infection, sexual intercourse, pregnancy and irritation of the urethra. Incipient symptom of PUC is not distinctness and can easily lead to misdiagnosis. The final diagnosis relied on transvaginal ultrasound-guided mass biopsy and urethral biopsy. Early tumor treatment is mainly based on surgical resection. For advanced tumors, it is recommended to adopt a comprehensive treatment plan combining surgery, radiotherapy and chemotherapy We report this case with the aim of bringing attention to that primary urethral cancer progresses rapidly and has a poor prognosis, it is urged to call for a need of diagnostic and treatment specification.

A novel electrospun nanofiber was developed using polyamide-6 (PA) and ε-poly-L-lysine (PL). PA is a popular textile polymer having desirable mechanical and thermal properties, chemical stability, and biocompatibility. However, PA nanofibers are prone to bacterial growth and user discomfort. PL, a natural homopolyamide, is non-toxic, antimicrobial, and hydrophilic but lacks spinnability due to its low molecular weight. Given its similar backbone structure as PA, with an additional amino side chain, PL was integrated with PA to develop multifunctional nanofibers. This study explores a simple, scalable method to obtain PL nanofibers by utilizing the structurally similar PA as the base. The goal was to enhance the functionality of PA by addressing its drawbacks. The study demonstrates spinnability of varying concentrations of PL with base PA while exploring compositions with higher PL concentrations than previously reported. Electrospinning parameters were studied to optimize the nanofiber properties. The effects of PL addition on morphology, hydrophilicity, thermal stability, mechanical performance, and long-term antimicrobial activity of nanofibers were evaluated. The inclusion of PL in PA-based nanofibers resulted in super hydrophilicity, increased tensile strength, and efficient antimicrobial properties with long-term stability. These enhanced characteristics hold promise for the composite nanofiber’s application in medical and protective textiles.

In this study, the degradable superhydrophobic Mg/P/Z/F/H (magnesi-um/poly(-caprolactone)/zinc oxide/1H,1H,2H,2H-perfluorodecyltriethoxysilane (PFDTES)/ heating process) composite materials were prepared through one-step method for enhancing the corrosion resistance of AZ91D magnesium alloys. Electrochemical measurements showed that Mg/P/Z/F/H materials significantly improved the corrosion resistance of magnesium alloys in 3.5 wt.% NaCl. The self-cleaning, adhesion and stability tests suggested that Mg/P/Z/F/H composite materials had well self-cleaning properties, good adhesion strength and stability in wet atmosphere.

The airborne and satellite-based synthetic aperture radar enables the acquisition of high-resolution SAR oceanographic images in which even the outlines of ships can be identified. The detection of ship targets from SAR images has a wide range of applications, such as the military, where the dynamic grasp of enemy targets can help improve the early warning capability of naval defence, and the civilian detection of illegal fishing vessels can help improve the level of maritime management. Due to the density of ships in SAR images, the extreme imbalance between foreground and background clutter, and the diversity of target sizes, achieving lightweight and highly accurate multi-scale ship target detection remains a great challenge. To this end, this paper proposes an attention mechanism for multiscale receptive fields convolution block (AMMRF). AMMRF not only makes full use of the location information of the feature map to accurately capture the regions in the feature map that are useful for detection results, but also effectively captures the relationship between the feature map channels, so as to better learn the relationship between the ship and the background. Based on this, a new YOLOv7-based ship target detection method, You Only Look Once SAR Ship Identification (YOLO-SARSI), is proposed, which acquires the abstract semantic information extracted from the high-level convolution while retaining the detailed semantic information extracted from the low-level convolution. Compared to the deep learning detection methods proposed by previous authors, our model is more lightweight, only 18.43M. We examined the effectiveness of our method on two SAR image public datasets: the High-Resolution SAR Images Dataset (HRSID) and the Large-Scale SAR Ship Detection Dataset-v1.0 (LS-SSDD-V1.0). The results show that the average accuracy AP50 of the detection method YOLO-SARSI proposed in this paper on the HRSID and LS-SSDD-V1.0 datasets is 4.9% and 5% higher than that of YOLOv7, respectively.

The threat of fine particulate matter concentration (PM2.5) is increasing globally, Tackling this issue requires an accurate understanding of its trends and drivers. The article investigates the PM2.5 characteristics of 285 prefecture-level cities in China from 2000-2018 based on multiscale geographically weighted regression(MGWR), and the results show that（1）previous studies based on classical MGWR models may be somewhat unstable, while MGWR can reflect the scale of influence of different variables on the dependent variable, and its regression results are more reliable.（2）PM2.5 is very sensitive to carbon emission(CE) factors, and there is a high degree of spatial heterogeneity, and the influence scale of location is the smallest among all variables, close to the municipal scale.（3）In 2000, the constant term all, IS, OFT, CE, and LT positively affect PM2.5, while GDP (jurisdiction) and UR negatively affect PM2.5; in 2010, the constant term all, GDP (jurisdiction), IS, OFT and LT positively affect PM2.5, while UR and CE negatively affect PM2.5; in 2018 the constant term all, IS, OFT and CE factors positively affect PM2.5, and GDP (jurisdiction), UR and LT negatively affect PM2.5.

(1) Background: Multiple alterations of cellular metabolism have been documented in experimental studies of autosomal dominant polycystic kidney disease (ADPKD) and are thought to contribute to its pathogenesis. (2) Methods: To elucidate the molecular pathways and transcriptional regulators associated with the metabolic changes of renal cysts in ADPKD, we compared global gene expression data from human PKD1 renal cysts, minimally cystic tissues (MCT) from the same patients, and healthy human kidney cortical tissue samples. (3) Results: We found PKD1 renal cysts displayed the Warburg effect with gene pathway changes favoring increased cellular glucose uptake and lactate production, instead of pyruvate oxidation. Additionally, mitochondrial energy metabolism was globally depressed, associated with downregulation of gene pathways related to fatty acid oxidation (FAO), branched-chain amino acid (BCAA) degradation, the Krebs cycle, and oxidative phosphorylation (OXPHOS) in renal cysts. Activation of mTORC1 and its two target proto-oncogenes, HIF-1α and MYC, was predicted to drive the expression of multiple genes involved in the observed metabolic reprogramming (e.g., GLUT3, HK1/HK2, ALDOA, ENO2, PKM, LDHA/LDHB, MCT4, PDHA1, PDK1/3, MPC1/2, CPT2, BCAT1, NAMPT); indeed, their predicted expression patterns were confirmed by our data. Conversely, we found AMPK inhibition was predicted in renal cysts. AMPK inhibition was associated with decreased expression of PGC-1α, a transcriptional coactivator for transcription factors PPARα, ERRα, and ERRγ, all of which play a critical role in regulating oxidative metabolism and mitochondrial biogenesis. (4) Conclusions: These data provide a comprehensive map of metabolic pathway reprogramming in ADPKD and highlight nodes of regulation that may serve as targets for therapeutic intervention.

Attribute reduction is a core technique in the rough set domain and an important step in data preprocessing. Researchers have proposed numerous innovative methods to enhance the capability of attribute reduction, such as the emergence of multi-granularity rough set models, which can effectively process distributed and multi-granularity data. However, these innovative methods still have many shortcomings, such as how to deal with complex constraints and how to perform multi-angle effectiveness evaluations. Based on the multi-granularity model, this study proposes a new method of attribute reduction, namely using multi-granularity neighborhood information gain ratio as the measurement criterion. This method combines both supervised and unsupervised perspectives, and by integrating multi-granularity technology with neighborhood rough set theory, constructs a model that can adapt to multi-level data features. This model can select the optimal granularity level or attribute set according to the requirements. Finally, the proposed method is experimented with on 15 UCI datasets against six other attribute reduction algorithms. The experimental outcomes, upon analysis and comparative review, substantiate the reliability and consistency of the attribute reduction approach introduced in this study.

Measuring Marginal Reflex Distance-1 (MRD-1) is a crucial clinical tool used to evaluate the position of the eyelid margin in relation to the cornea. Traditionally, this assessment has been conducted manually by plastic surgeons, ophthalmologists, or trained technicians. However, with the advancements in Artificial Intelligence (AI) technology, there is a growing interest in the development of automated systems capable of accurately measuring MRD-1.In this context, we introduce novel MRD-1 measurement methods based on deep learning algorithms that can simultaneously capture images and compute the results. This prospective observational study involved 154 eyes of 77 patients aged over 18 years who visited Chungnam National University Hospital between September 1, 2023, and July 29, 2023. We collected four different MRD1 da-tasets from patients using three distinct measurement methods, each tailored to the individual patient. The mean MRD1 values, measured through the manual method using a penlight, the deep learning method, ImageJ analysis from RGB eye images, and ImageJ analysis from IR eye images in 56 eyes of 28 patients, were 2.64 ± 1.04 mm, 2.85 ± 1.07 mm, 2.78 ± 1.08 mm, and 3.07 ± 0.95 mm, respectively. Notably, the strongest agreement was observed between MRD1_deep learning (DL) and MRD1_IR (0.822, p < 0.01). In the Bland-Altman plot, the smallest difference was observed between MRD1_DL and MRD1_IR ImageJ, with a mean difference of 0.0611 and △LOA (limits of agreement) of 2.5162, which is the smallest among the other groups. In conclusion, this novel MRD1 measurement method, based on an IR camera and deep learning, demon-strates statistical significance and can be readily applied in clinical settings.

The aim of this study was to study the effect of leisure identity, flow, satisfaction, and re-participate intention among outdoor leisure activity participants in South Korea. Due to the recent COVID-19 pandemic, there has been a tendency to more frequently participate in outdoor leisure activities as opposed to indoor leisure activities. Leisure activities bestow various benefits. Therefore, this study was used to analyze the relationships amongst leisure identity, flow, leisure satisfaction, and re-participate intention among various theories about leisure. The participants in this study were collected from amongst 369 people who were frequent participants in outdoor leisure activities. For the data analysis, the researchers used frequency, confirmatory analysis, reliability, correlation and structural equaling modeling. The findings were as follows: First, leisure identity had wielded an influence on leisure flow. Second, leisure identity had influence leisure satisfaction. did not have any significant influence on recreation specialization. Third, leisure identity had influence on re-participate intention. Fourth, leisure flow did not have any significant influence on leisure satisfaction. Fifth, leisure flow did not have any significant influence on leisure satisfaction. And finally, leisure satisfaction had an influence on re-participate intention. In the era of the COVID-19 pandemic, a new leisure identity has been formed, and it is believed to be a new study on leisure flow, leisure satisfaction, and re-participation intention. This study aims to provide basic data for constructing infrastructure to enable continued participation in outdoor sports in Korea.

Using numerical simulation method, combined with the pre-branch material characteristics of the measurement results, based on the LS-DYNA software to simulate the branch crushing process, the analysis found that not only the existence of the cutter cutting in the branch destruction process, there is also the cutting of the opposing surface of the bending fracture, with the increase in the speed of the knife rollers, the cutter cutting resistance increases, the cutting resistance reaches 2690 N when the cutter at 2500 r/min, the cutter cutting resistance is the smallest in the cutting simulation at the blade angle of 55°, the blade angle is more suitable for the cutting of the branch. In the cutting simulation under different cutting edge angles, the cutting resistance of the tool is the smallest when the edge angle is 55°, which is 1860 N. This edge angle is more suitable for branch crushing and cutting. Using Fluent software to analyse the airflow characteristics of the crushing device, it was found that with the increase of the knife roller speed, the inlet flow and negative pressure of the crushing chamber are increasing, the speed of 2500 r/min, the inlet flow and negative pressure were 1.92 kg/s and 37.16 Pa, which will be conducive to the feeding of branches, but the speed is too high and it will also lead to the enhancement of the vortex of part of the area in the crushing device, which will affect the feeding of branches and the throwing of the crushed material. affect the feeding of branches and the throwing out of crushed materials, and finally determined the speed range of the crushing knife roller is 1800 ~ 2220 r/min. Based on ANSYS/Model module modal analysis of the crushing knife roller, the knife roller of the first six orders of the intrinsic frequency and vibration pattern, crushing knife roller of the lowest order of the modal intrinsic frequency of 137.42 Hz, much larger than the crushing knife roller operating frequency of 37 Hz, the machine will not resonate during operation.