Nanoparticles of graphene and carbon nanotubes are attractive materials for improvement of mechanical and barrier properties and functionality of biodegradable polymers for food packaging applications. However, the increase of the manufacture and consumption increases the probability of exposure of human and environment to such nanomaterials, this rising questions about the risks of nanomaterials since they can be toxic. For a risk assessment, it is crucial to know whether airborne nanoparticles of graphene and carbon nanotubes can be released from nanocomposites into the environment at their end-life, or they remain embedded in the matrix. In this work the release of graphene and carbon nanotubes from the poly(lactic) acid nanocomposite films were studied for the scenarios of: (i) biodegradation of matrix polymer at the disposal of wastes; and (ii) combustion and fire of nanocomposite wastes. Thermogravimetric analysis in air atmosphere, TEM, AFM and SEM were used to verify the release of nanoparticles from nanocomposite films. The three factors model was applied for the quantitative and qualitative risk assessment to the release of graphene and carbon nanotubes from nanocomposite wastes for these scenarios. Safety concern is discussed in respect to the existing regulations for nanowastes stream.

The aim this text to present the confined covariant quark model (CCQM) and review its applications to the decays of B mesons. We do so in the context of existing experimental measurements and theoretical results of other authors, which we review also. The physics principles are in detail exposed for the CCQM, the other results (theoretical and experimental) are surveyed in an enumerative way with comments. We proceed by considering successively three categories of decay processes: leptonic, semileptonic and non-leptonic.

This paper secures the analytical soliton solutions of the perturbed NLSE gives to (1). The existence criteria have been demonstrated and the wave speed of the soliton befall out. To achieve all the results obtained we used the mathematical technique. In view of the results obtained, some new additional one have been reported in left-handed metamaterials.

We apply utilized the extended form of the auxiliary equation method to obtain extensively reliable exact travelling wave solutions of perturbed Gerdjikov–Ivanov equation (GIE) that is widely used as a model in the field theory of quanta and non-linear optics. The method is based on a simple first order second degree ODE. The new form of the approach gives more solutions to the governing equation efficiently.

A model is proposed that describes the transfer of ions and the process of water dissociation in a system with a bipolar membrane and adjacent diffusion layers. The model considers the transfer of four types of ions: the cation and anion of salt and the products of water dissociation – hydrogen and hydroxyl ions. To describe the process of water dissociation, a model for accelerating the dissociation reaction with the participation of ionogenic groups of the membrane is adopted. The boundary value problem is solved numerically using COMSOL® Multiphysics 5.5 software. An analysis of the results of a numerical experiment shows that, at least in a symmetric electromembrane system, there is a kinetic limitation of the water dissociation process, apparently associated with the occurrence of water recombination reaction at the of the bipolar region. An interpretation of the entropy factor (β) is given as a characteristic length which shows the possibility of an ion that appeared as a result of the water dissociation reaction to be removed from the reaction zone without participating in recombination reactions.

In the evolving landscape of cybersecurity threats, the Permanent Denial of Service (PDoS) attacks have emerged as a particularly damaging form of cyber aggression. Unlike the more well-known Denial of Service (DoS) attacks, which disrupt services temporarily, PDoS attacks aim to inflict irreversible damage to systems, often resulting in significant system overhauls and requiring hardware replacement. To enable the development of effective security measures, but also to address the knowledge gaps, this paper offers an in-depth exploration of PDoS attacks, emphasizing their distinguishing characteristics, underlying mechanisms, and potential further development. Through a comprehensive case study, the research highlights diverse tactics and strategies employed by attackers, from targeting IoT devices to manipulating boot processes and exploiting firmware vulnerabilities. A novel classification of PDoS attack vectors is proposed, that also explains the ways in which the systems can be compromised. The findings confirm the pressing need for adaptive and robust defense mechanisms to mitigate the threats posed by PDoS attacks in our interconnected digital world.

Alloys based on TiNi are widely used in various fields of technology and medicine. In the present work, we report on preparation of TiNi-alloy based wire with the shape memory effect, which was used for compression clips for surgery. Composition and structure of the wire, and its martensitic and physical-chemical properties were studied using SEM, TEM, optic microscopy, profilometry, mechanical tests, etc. The TiNi alloy was found to consist of B2 and B19' and secondary-phase particles of Ti2Ni, TiNi3 and Ti3Ni4. Its matrix was slightly enriched in Ni (50.3 at. % of Ni). Homogeneous grain structure was revealed (an average grain size of 19±0.3 μm) with equal quantities of grain boundaries of special and general types. Surface oxide layer provide improved biocompatibility and promote adhesion of protein molecules. Overall, the obtained TiNi wire was concluded to exhibit martensitic, physical and mechanical properties suitable for its use as an implant material. The wire was then used for manufacturing compression clips with the shape memory effect and applied in surgery. The medical experiment that involved 46 children demonstrated that the use of such clips in children with double-barreled enterostomies permitted to improve the results of surgical treatment.

In recent years, there has been an increasing demand for personalized experiences in various domains, including the cultural and educational sectors. Museums, as custodians of art, history, and scientific knowledge, are seeking innovative ways to engage their visitors and provide tailored content that enhances their understanding and appreciation of the exhibits. This article presents ExhibitXplorer, a distributed architecture service that leverages geofencing, artificial intelligence, and microservices to enable personalized content delivery in museums. By combining implicit and explicit segmentation of museum visitors and utilizing the GPT API for content generation, ExhibitXplorer offers a dynamic experience to different visitor segments, including researchers, students, casual visitors, and children. The system utilizes push notifications triggered by visitor location changes, allowing seamless delivery of personalized information both indoors and outdoors. Tests were conducted to evaluate the user experience of visitors to an outdoor ethnographic museum. The results showed that 55% of the test participants were satisfied and 45% very satisfied with the way personalized content was delivered.

The results of applying drilling engineering tools in planned deviated and horizontal wells of oil and gas condensate fields have been examined. The basis for the implementation of a comprehensive approach was the information obtained from drilling horizontal wells in the West and East Siberia, Volga-Ural region, and Iraqi Kurdistan. A synthetic model is considered as an example of the data, incorporating geomechanical and geological properties. As a result of the conducted audit of the geomechanical model and drilling process, the methodologies used were further developed to obtain optimal drilling fluid densities, aiming to prevent cavity formation on well walls, hydraulic fractures, and other related issues. The implementation of the Python programming language was introduced in the stages of geomechanical model preparation, resulting in a time acceleration of up to 20%. During the pre-drilling stage, technological operations were synchronized with the geomechanical model, increasing the involvement of process participants through the synchronization of knowledge areas. The interrelation between drilling technology, drilling parameters, properties of flushing fluids, and rock stability analysis was established, ensuring a 5% increase in construction speed (through NPT reduction and modification of existing tools and technological operations) and accident-free drilling of complex deviated and horizontal wells, provided that the recommended drilling parameters are followed.

This paper presents a new semi-explicit algorithm for parameters estimation in a time-fractional generalization of dual-phase-lag heat conduction model with the Caputo fractional derivatives. It is shown that this model can be derived from a general linear constitutive relation for the heat transfer by conduction when the heat conduction relaxation kernel contains the Mittag-Leffler function. The model can be used to describe heat conduction phenomena in a material with power-law memory. The proposed algorithm of parameters estimation is based on the time integral characteristics method. The explicit representations of the thermal diffusivity and the fractional analogues of the thermal relaxation time and the thermal retardation are obtained via a Laplace transform of the temperature field and utilized in the algorithm. An implicit relation is derived for the order of fractional differentiation. In the algorithm, this relation is resolved numerically. An example illustrates the proposed technique.

OSI model used to be common network model for years. In the case of ad hoc networks with dynamic topology and difficult radio communications conditions, gradual departure is happening from the classical kind of OSI network model with a clear delineation of layers (physical, channel, network, transport, application) to the cross-layer approach. The layers of the network model in ad hoc networks strongly influence each other. Thus, the cross-layer approach can improve the performance of an ad hoc network by jointly developing protocols using interaction and collaborative optimisation of multiple layers. The existing cross-layer methods classification is too complicated, because it’s based on the whole manifold of network model layers combinations, regardless their importance. In this work, we review ad hoc networks cross-layer methods, propose the new useful classification of cross-layer methods, and show future research directions in ad hoc networks cross-layer methods development. The proposed classification can help to simplify the goal-oriented cross-layer protocol development.

Two Iron Age settlements, Tuzusai and Taldy Bulak 2 (ca. 500 BCE to 1 CE), located in Southeastern Kazakhstan on the Talgar alluvial fan north of the Tian Shan range, have yielded a small collection of bone, antler/horn, bronze, and stone artifacts with affinity to nomadic art of the first millennium BCE. Both settlements date within the period of late Saka culture. Two pieces have decorative ornamentations with zoomorphic imagery: a small carved fragment of a with carved images of a wing and an ear and a perforated bone disk with the carving of three birds’ heads. The other artifacts include objects associated with Saka weaponry or nomadic economy such as the two antler/horn psalia (cheek pieces) and a bronze amulet. A carnelian bead will also be described as an imported object. These special finds are found on the occupation floors of mud brick houses and pit houses of settlements, not in grave or burial contexts. The objects are placed in stratigraphic sequence in the settlement sites. Then the method for placing these objects within the chronological framework of “animal-style art” is through comparisons with similar objects found throughout Eurasia—a method used in Soviet and Post-Soviet archaeology. The results show that functional and stylistic elements of the six objects indicate that the Talgar settlements were part of a larger world-system of trade and communication along the early Silk Route(s).

Wave buoy measurements were carried out near the north-eastern Black Sea coast at the natural reserve Utrish in 2020-2021. In total, about 11 months of data records were collected during two stages of the experiment at 600 and 1500 meters offshore and depths of 18 and 42 meters. The measured waves propagate almost exclusively from the seaward directions. Generally, the waves do not follow the local wind directions, thus, implying a mixed sea state. Nevertheless, dimensionless wave heights and periods appears to be quite close to the previously established empirical laws for the wind-driven seas. The results of the wave turbulence theory are applied for estimates of spectral energy fluxes and their correspondence to the energy flux from the turbulent wind pulsations. These estimates are consistent with today's understanding of wind-wave interaction. It is shown that the main fraction of the wind energy flux goes to the direct Kolmogorov-Zakharov cascade to high wave frequencies and then to dissipation in small scales. Less than 1% of the wind energy flux is directed to low frequency band (the so-called inverse Kolmogorov-Zakharov cascade), thus, providing wave energy growth.

A unique two-column ²³⁰U/²²⁶Th generator has been developed. The focus was hold on obtaining ²²⁶Th of high purity in a solution amenable to further labeling. The first column of the proposed generator filled with TEVA Resin held ²³⁰U, from which ²²⁶Th was eluted with 7 M HCl solution. UTEVA Resin pretreated with nitric acid solution was used as a sorbent for the second column for thorium retention. ²²⁶Th was extracted with 0.01-0.05 M citric buffer solution. One cycle of generator milking took 5-7 minutes and produced > 90% of ²²⁶Th in 1.5 ml of eluate, pH 4.5-5.0. The proposed two-column ²³⁰U/²²⁶Th generator was tested over two months including a second loading of ²³⁰U additionally accumulated from ²³⁰Pa. The ²³⁰U impurity in ²²⁶Th eluate was less than 0.01% allowing to use it directly in synthesis of radiopharmaceutical compounds.

In this paper, the authors consider the influence of the type of power supply and the internal parameters of the DC-DC converter on the stability of the system at constant power load. The stability of the system under consideration is important in the design and development of the power supply system for an autonomous consumer. Such a typical system can be a DC microgrid. In the work, when analyzing the stability of the system, the power source is not considered an ideal voltage source, but the active-inductive nature of the voltage source is taken into account, which is equivalent to using a synchronous machine with permanent magnets. The Rauss-Hurwitz algebraic criterion was used as a criterion for analyzing the stability of the system. This will make it possible to build and analyze the areas and boundaries of the system's stability. As a result, the areas and boundaries of the stability of the system were presented. The general trend towards the behavior of the zone of instability of the system was given. At the same time, dependences describing the boundaries of instability are presented, which are combinations of parameters of the DC-DC converter, beyond which the system becomes unstable. The presented definitions of the instability limits can be used as a corrective device of the control system to ensure the stability of the system in the upper limits of the power consumption.

The subject of the research is the investigation of the behavior of railway tracks in locations with a significant change in the stiffness of the track. These locations can be designed from various structural elements and their materials, and this mainly results in a height change of the track level during its operation. These transition zones are monitored and expertly examined in order to detect undesirable deformations of the geometrical position of the track caused by the trains running. The transition zones are at the points where the fixed track transitions to the classic track bed, in our case it is their combination with bridge structures, especially at their supports. In Slovakia, under the conditions of the Railways of the Slovak Republic, the issue is topical within the framework of the modernization of trans-European railway corridors. The results of experimental measurements and their analysis will provide relevant data for subsequent research solutions for their new numerical modeling, which will ensure a smooth passage through these points of change without height fluctuations, vibrations, and shocks from the wheels of train sets.

The electrification of process industries is one of the main challenges when building a low-carbon society since they consume huge amounts of fossil fuel generating different emissions. Heat pumps are one of the instruments to perform industrial sector of carbon-neutral market players. This paper proposes an approach to improve the economic feasibility of heat pumps within the process plants. Initial energy targeting with Grand Composite Curves was used and supplemented with the detailed design of the evaporator and compressor for different condensation and evaporation pressures. The trade-off between the capital cost of the heat pump and the electricity cost was investigated and optimal configurations were selected. The case study investigates the gas fractioning unit of a polymer plant where three heat pumps were integrated into distillation columns. The results demonstrated that the heat recovery is 174 MW and requires an additional 37.9 MW of electricity to reduce hot utility by 212 MW. The selection of evaporation and condensation pressure of heat pumps allows saving of 21.5 M€/y for 7 years of plant operation.

Biological control, a well-established plant protection method, has garnered substantial attention in recent decades. Various approaches, including biological control agents (BCA), catch crops, biofumigation, sticky traps, and pheromones, have been extensively explored. While the effectiveness of these methods varies depending on specific circumstances, their collective significance has grown amid mounting pressures to curtail or eliminate conventional synthetic plant protection products. Previous review articles have highlighted the synergistic benefits of using two or more BCAs simultaneously, yet limited information exists regarding the concurrent use of diverse biological control methods. This comprehensive review incorporates a thorough literature search to assess the synergistic potential of concurrently employing two or more of these methods, followed by a discussion on perspectives of holistic management and mimicking of complex natural systems, shedding light on the vast potential and need for further research in this domain.

We conducted an in-situ crystal structure analysis of ferroselite at non-ambient conditions. The aim is to provide a solid ground to further the understanding of the properties of this material in a broad range of conditions. Ferroselite, marcasite-type FeSe2, was studied under high pressures up to 46 GPa and low temperatures, down to 50 K using single-crystal microdiffraction techniques. High pressure and low temperatures were generated using a diamond anvil cell and a cryostat. We found no evidences of structural instability in the explored P-T space. The deformation of the orthorhombic lattice is slightly anisotropic. As expected, the compressibility of the Se-Se dumbbell, the longer bond in the structure, is larger than that of the Fe-Se bonds. Less obvious is the behavior of the octahedral bonds, the shorter bond is the most compressible determining a small increase in the octahedron distortion with pressure. We also achieved a robust structural analysis of ferroselite at low temperature in the diamond anvil cell. Structural changes upon temperature decrease are small but qualitatively similar to those produced by pressure.

Abstract: The aim of this study was to identify and quantify polyphenolic compounds in skin extracts from four Bulgarian grape varieties and compare to those of seed extracts. The values of total phenolic contents (TPC), flavonoids, anthocyanins, procyanidins, ascorbic acid in grape skin extracts were determined. The antioxidant capacities of skin extracts were evaluated by DPPH, ABTS, FRAP and CUPRAC methods. The TPC values of skin extracts were 2-3 times lower than those of seed extracts. The significant difference between total parameters values of individual grape varieties were also found. According to the TPC and antioxidant capacity of skin extracts the different grape varieties were in the following order: Marselan ≥ Pinot Noir ˃ Cabernet Sauvignon ˃ Tamyanka. The individual compounds in the grape skin extracts were determined by RP-HPLC and compared with those of seed extracts. The determined composition of skin extracts was significant different from seed extracts composition. Qualitative and quantitative evaluation of the procyanidins and catechins in the skins were carried out. A correlation between phenolic contents, individual composition and antioxidant capacity of different extracts was found. The studied grape extracts have a potential to be applied as natural antioxidants in the pharmaceutical and food industries.

Chymotrypsin is an important proteolytic enzyme in human digestion system that cleaves milk proteins, through hydrolysis reaction, which makes it interesting subject to study activity of milk proteases. In this work, we compared detection of chymotrypsin by spectrophotometric, dynamic light scattering (DLS) and quartz crystal microbalance (QCM) methods and determined the limit of chymotrypsin detection (LOD), 0.15 ± 0.01 nM for spectrophotometric, 0.67 ± 0.05 nM for DLS and 1.40 ± 0.30 nM for QCM methods, respectively. We discuss peculiarities and give perspective for implementation of detection methods and note that while the optical detection methods are simple to implement, the QCM method is more robust for sample preparation. We give an overview on methods and instruments for detection of chymotrypsin and other milk proteases.

The purpose of the present study was to develop an experimental model for studying of the intra-articular knee movements depending on the work of the knee joint and applied muscle groups in isometric stretching conditions with different tens. The experimental procedure includes ultrasound examination of a knee joint after isometric stretching of healthy men (n=32). The changes in millimeters of the distances between the femur and tibia were measured with ultrasound sonographer at three stages. The first stage was performed on ten (n=10) healthy men at five different sitting and upright positions. In the second and third experimental model stages the lower limbs loading was on 22 participants. Our hypothesis which was confirmed, was that as a result of increasing extraloads on the participants back (2, 5, 10, 15, 17, 20 kg), a intra-articular decrease in the femur-tibia cartilage surface distance wiil be observed. The accuracy of the created experimental model was improved over its three stages from 30% to 9%. Quantitative model data can help to create a mathematical model for the mechanical effects during deformation of the knee joint bone cartilage, as well as to outlines the some future tasks: increasing loading weights; enlarge participant groups; comparison men and women; healthy and pathology comparison.

New multilayer 3D nanocomposite wear-resistant ion-plasma hard and superhard coatings Avinit [(TiN-AlN)(Mo-Cr-V-Si)]_n have been developed.The introduction of additional alloying elements (Mo, Cr, V, Si) into the Ti-Al-N coating composition, which have a high affinity for nitrogen and are capable of forming strong nitride nanoparticles in the Ti-N and Al-N layers.This makes it possible to obtain hard and superhard hardening coatings.The metallographic and tribological studies carried out indicate the prospects of the developed multicomponent multilayer nano- and microstructured Avinit coatings for increasing wear resistance and reducing friction coefficients.This paper is devoted to the development and implementation of Avinit vacuum plasma technologies for strengthening cutting and forming tools to improve tool performance.Production tests of cutting tools with Avinit's developed multilayer wear-resistant ion-plasma coatings in production conditions at many large machine-building enterprises have shown their high efficiency.In serial production, the wear resistance of tools increases by 3 to 30 times, stamps by 5 to 100 times, and parts rubbing against abrasive materials by 10 to 100 times.Avinit's vacuum plasma technologies have been successfully implemented in production in the aggregate and engine building, transport engineering, and power engineering industries.Positive experience in applying multicomponent coatings has been gained not only when applying hardening coatings to manufactured cutting tools, but also after regrinding to regrindable carbide cutting tools from domestic and foreign manufacturers.

Floating Offshore Wind Turbine (FOWT) is an innovative technology with little industry guidance for its hull design. Various FOWT floaters with different hull shapes claim to support the same turbines. Structural integrity and material expense analyses of different pontoon shapes were conducted, and it was found that some configurations, such as those with every two columns connected by both pontoon and bracing, have advantages over others. However, it is important to note that the choice of pontoon shape should be based on the wave loading conditions the floater will be exposed to. While a T-shaped pontoon provides a cost-effective solution under certain wave loading scenarios, it may not be the best option for all conditions. Specifically, ring pontoon designs with full bracing were found to be necessary for withstanding certain wave loads. Therefore, it is important to consider different Dominant Load Parameters (DLP) and ensure that a FOWT floater can withstand all applicable DLPs. An uneven hexahedral column shape, which combines the best attributes of square and round shapes, is proposed as a better alternative to cylindrical columns. It offers ease of manufacture and reasonably low drag. Bracing is found to be necessary for withstanding the wind turbine’s incurred moment and forces. The conclusion is that platform design should prioritize manufacturing costs and strength over maximizing hydrodynamic performance.

This paper investigates reachable set estimation and state-feedback controller design for linear time-delay control system with bounded disturbances. First, by constructing an appropriate Lyapunov-Krasovskii functional, we obtained a delay-dependent condition, which determed the admissible bounding ellipsoid for the reachable set of the system we considered. Then, a sufficient condition in form of liner matrix inequalities is given to solve the problem of controller design with reachable set estimation. Finally, by minimizing the volume of the ellipsoid and solving the liner matrix inequality, we obtain the desired ellipsoid and controller gain. A comparative numerical example is given to verify the usefulness of our result.

Hydrozoans are widely known for their complex life cycles. The life cycle usually includes an asexual benthic polyp, which produces a sexual zooid (gonophore). Here, we performed an extensive analysis of 183 specimens of hydrozoan genus Sarsia from the White Sea and identified four types of gonophores. We also compared the type of gonophore with haplotypes of molecular markers COI and ITS. Analysis of COI sequences recovered that the studied specimens relate to the species S. tubulosa, S. princeps and S. lovenii, and that S. lovenii specimens divide into two COI-haplogroups. More intraspecies genetic diversity was revealed in the analysis of ITS sequences. Sarsia tubulosa specimens divide into two ITS-haplotypes, and presumably, hybrid forms between these lineages were found. For S. lovenii, we identified 14 ITS-haplotypes as a result of alleles separation. Intra-individual genetic polymorphism of ITS-region is most likely associated with intraspecific hybridization between different haplotypes. The diversity of morphotypes is associated with the genetic diversity of the specimens. Thus, we demonstrated that the morphologically variable species S. lovenii is represented in the White Sea by a network of intensively hybridizing haplotypes. Hybridization affects the morphology and maturation period of gonophores and presumably affects the processes of speciation.

The pentose phosphate pathway (PPP) is one of three major pathways involved in glucose metabolism, regulated by glucose-6-phosphate dehydrogenase (G6PD), controlling NADPH formation. NADPH, in turn, regulates the balance of oxidative stress and reactive oxygen species (ROS) levels. G6PD dysfunction, affecting PPP, is implicated in neurological disorders, including epilepsy. However, PPP's role in epileptogenesis and ROS production during epileptic activity remains unclear. To clarify these points, we conducted electrophysiological and imaging analyses on mouse hippocampal brain slices. Using the specific G6PD inhibitor G6PDi-1, we assessed its effects on mouse hippocampal slices, examining intracellular ROS, glucose/oxygen consumption, and ROS production during synaptic stimulation and in the 4AP epilepsy model. G6PDi-1 increased basal intracellular ROS levels and reduced synaptically induced glucose consumption but had no impact on ROS production from synaptic stimulation. In the 4AP model, G6PDi-1 didn't significantly alter spontaneous seizure frequency or H2O2 release amplitude but increased the frequency and peak amplitude of interictal events. These findings suggest that short-term PPP inhibition has a minimal impact on synaptic circuit activity.

This paper discusses the preliminary results of archaeological surveys conducted in the Juuku Region of north-central Kyrgyzstan on the south side of Lake Issyk kul. Our goal was to document ancient and contemporary agropastoral systems over a four millenia time period. During the surveys about 350 loci were identified as settlements, burial mounds, graves, single artifact finds, and artifact scatters (ceramic). The areas of Juuku Valley survey included two discrete polygons: Polygon 1, Lower Juuku at 1750 to 1950 m asl in elevation and Polygon 2, Chak Juuku or Upper Eastern Branch Juuku Valley at 2060 to 2100 m asl in elevation. Three radiometric dates and preliminary archaeobotanical studies were conducted at three exposed profile cuts. The methods included here are: (1) pedestrian surveys; (2) use of digital maps (Google Earth, Encarta); (3) placing archaeological loci within known chronological time periods; (4) AMS dating of charcoal samples collected from profile deposits; and (5) preliminary identification of plant remains found from archaeobotanical samples. The results of our research represent the first step toward inventorying and interpreting archaeological data in the Juuku Valley derived from field studies.

An extended classification of active RC- and RLC- filters with Sallen-Key architectures, including those created in the last three years, is proposed. This makes it possible to formulate new design directions for an extended family of active RC- and RLC- Sallen-Key filters (PF, LPF, HPF, RF) for the tasks of high-speed and ultra-fast analog-to-digital signal conversion.

This study focuses on the modification of ion-exchange membranes by incorporating phosphorylated dendrimer into sulfonated polytetrafluoroethylene membranes to enhance specific selectivity between mono-/divalent ions, using the Ca2+/Na+ pair as an example. The research employs mechanical, physico-chemical, and electrochemical analyses to explore the effects of P-H20 incorporation on membrane properties. Bulk modification significantly increases membrane selectivity towards calcium ions (specific permselectivity coefficient rises from 1.5 to 7.2), while maintaining the same level of the limiting current density. Other findings indicate that bulk modification significantly changes the transport-channel structure of the membrane and alters the mechanism of over-limiting mass transfer. The over-limiting current for the pristine membrane is mainly due to non-equilibrium electroconvection, while modified membranes actively participate in the water-splitting reaction, leading to the suppression of the electroconvection. Despite this drawback, the decrease of the over-limiting potential drop results in a decrease in specific energy consumption from 0.11 to 0.07 kWh/mol. In the under-limiting current mode, the specific energy consumption for all studied membranes remains within the same limits of 0.02-0.03 kWh/mol.

Whole-genome DNA sequencing of Lactobacillus D75 and D76 strains (Vitaflor, Russia) was performed using the PacBio RS II platform, followed by de novo assembly with SMRT Portal 2.3.0. The average nucleotide identity (ANI) test showed that both strains belong to the Lactobacillus helveticus, but not the L. acidophilus as previously assumed. 31 exopolysaccharide (EPS) production genes (nine of which form a single genetic cluster), 13 adhesion genes, 38 milk protein and 11 milk sugar utilization genes, 13 genes for and against specific antagonistic activity, aight antibiotic resistance genes, and also three CRISPR blocks and eight Cas I-B system genes were identified in the genomes of the both strains. The expression of some genes was confirmed. In fact, the presence of identified genes suggests that L. helveticus D75 and D76 are able to form biofilms on the outer mucin layer, inhibit the growth of pathogens and pathobionts, utilize milk substrates with the formation of digestible milk sugars and bioactive peptides, resist bacteriophages and show some genome-determined resistance to antibiotics, stimulate the host’s immune system. Pathogenicity genes have not been identified. The study results confirm the safety and high probiotic potential of the strains.

Earthworm invasions often reduce biodiversity and affect the ability of ecosystems to perform ecosystem functions. Over the past few decades, European lumbricide species have spread widely in natural habitats in Western Siberia, without completely displacing the native species. The aim of the present experiment is to study the survival, reproductive potential, vertical distribution, abundance, and biomass of Aporrectodea caliginosa and Lumbricus rubellus invasive for the region and the native species Eisenia nordenskioldi and their influence on each other. For this purpose, winter and vegetation experiments were conducted in mesocosms simulating the real situation of invasions in the same communities on the same types of soils with the same amount and composition of litter. The authors found that the native species was significantly inferior to A. caliginosa in reproduction rate, number of offspring, and final biomass, but had an advantage over L. rubellus. The native species was positively influenced by the presence of A. caliginosa. In the experiment, there was a significant rejuvenation of the populations of the studied species, an increase in abundance and relative mass under interaction conditions compared to mono variants. The native species had advantages over the invasive species in terms of winter survival. The natural volume of litter used in the experiment was insufficient for L. rubellus. According to the results of the experiment, it can be assumed that the spread of L. rubellus will continue to be limited to non-freezing biotopes rich in organic matter. A. caliginosa will spread in natural communities and agrocenoses of Western Siberia.

A new low-pass filter (LPF) circuit with independent adjustment of various, incl. digitally controlled, pole frequency resistors, pole quality factor and transmission coefficient. The proposed low-pass filter is based on the use of the properties of a multi-differential operational amplifier that performs the functions of a signal adder. The peculiarity of the filter is that it has three inputs, with respect to which different transmission coefficients are implemented, incl. inverting (-1) and non-inverting (+1). To check these properties of a low-pass filter in the Micro-Cap environment, computer simulation of a specific circuit was performed on a multi-differential operational amplifier AD 8130. Mathematical expressions are given for the main parameters of the proposed low-pass filter, which allow parametric synthesis of elements of a specific circuit under given restrictions on the used element base.

The study was performed to get the first insight of distribution of the low field volume magnetic susceptibility (MS) throughout the Zagreb city area, based on in-situ field measurements. Most interesting locations were selected for soil sampling and geochemical content was determined using ICP-OES. A geostatistical approach was applied on MS and geochemical results. Median value of 0.245 x 10-3 SI units is proposed to be used as relevant average MS value in Zagreb area. Mean concentrations of heavy metals in Zagreb soils (in µg/g) are: Pb (36.82), Zn (87.77), Cu (30.84), Cd (0.66), Cr (29.04), Co (11.89) and Ni (28.40), being relatively low in comparison with Croatian legislation and with European and world average. Boxplot analyses showed that 45% of studied elements do not show any anomaly, while the rest of elements mostly show only one weak anomaly and they are located at the same sites as MS anomalies. Statistical analysis found significant correlations between MS and following elements: Cd, Co, Fe, Mn, Na, Pb, Sb and Zn. In-situ MS measurements proved to be an efficient tool for initial screening of large areas in terms of elevated heavy elements concentrations, enabling cheap and fast assessment of state of environment.

A new circuit of a low-pass filter (LPF) is considered, which is switched on at the input of analog-to-digital converters to limit the spectrum of input signals. The peculiarity of the proposed low-pass filter is the independent adjustment of the pole frequency, the quality factor of the pole and the transmission coefficient by different resistors. Computer simulation performed in the Micro-Cap environment confirms these properties of the LPF. The basic mathematical expressions are obtained, which make it possible to carry out the parametric synthesis of the LPF circuit. It is shown that the sensitivity of the LPF transmission coefficient to changes in the parameters of the frequency-setting elements of the circuit is close to zero and depends only on the ratio of the resistances of the two resistors in the feedback circuit.

The Simplified Spherical Harmonic (SPN) approximation was first introduced as a three-dimensional (3-D) extension of the plane-geometry Spherical Harmonic (PN) equations. A third order SPN (SP3) solver, recently implemented in the Nodal Expansion Method (NEM), has shown promising performance in the reactor core neutronics simulations. This work is focused on the development and implementation of the transport corrected interface and boundary conditions in NEM SP3 solver, following recent published work on the rigorous SPN theory for piecewise homogeneous regions. A streamlined procedure has been developed to generate the flux zero and second order/moment discontinuity factors (DFs) of the generalized equivalence theory to eliminate the error introduced by pin-wise homogenization. Moreover, several color set models with varying size and configuration are later explored for their capability of generating DFs that can produce results equivalent to that using the whole-core homogenization model for more practical implementations. The new developments are tested and demonstrated on the C5G7 benchmark. The results show that the transport corrected SP3 solver shows general improvements to power distribution prediction compared to the basic SP3 solver with no DFs or only zero order/moment DFs. The complete equivalent calculations using the DFs can almost reproduce transport solutions with high accuracy. The use of equivalent parameters from larger size color set models show better prediction in the whole-core calculations. By coupling different color set models DFs can offer the best accuracy at both eigenvalues and power distributions.

This study presents a pre-processing approach adopted for the radar reflectivity data assimilation and results of simulations with the Harmonie numerical weather prediction model. The method shows an improvement of precipitation prediction within the radar location area in both the rain rates and spatial pattern presentation. With the assimilation of radar data, the model simulates larger water content in the middle troposphere within the layer from 1 to 6 km, with major variations at 2.5–3 km; it also reproduces better the mesoscale belt and cell patterns of precipitation fields.

Although pollination is one of the most crucial biological processes that ensures plant reproduction, its mechanisms are poorly understood. Especially in insect-mediated pollination, a pollen undergoes several attachment and detachment cycles when being transfered from anther to insect and from insect to stigma. The influence of the surface properties of pollen, insect and floral surfaces on the adhesion forces that mediate pollen transfer are poorly studied. Here, we investigate the adhesive properties of Hypochaeris radicata pollen and their dependence on pollen ageing by quantifying the pull-off forces from glass slides using centrifugation and atomic force microscopy. We found that the properties of the pollenkitt – the viscous, lipid liquid on the surface of most pollen grains – influences the forces necessary to detach a pollen from hydrophilic surfaces. Our results show that aged H. radicata pollen form weaker adhesions to hydrophilic glass than fresh ones. On the other hand, when a pollen grain ages in contact with glass, the adhesion between the two surfaces increases over time. This study shows for the first time the pollen ageing effect on the pollination mechanism.

In this work, the possibility of fabrication magneto-optical ceramics by vacuum sintering of compacts prepared by electrophoretic deposition (EPD) from suspensions of (Ho0.95La0.05)2O3 (HoLa) nanopowders made by self-propagating high-temperature synthesis and (Y0.9La0.1)2O3 (YLa) nanopowders made by laser synthesis was systematically investigated. The processes of the formation of bulk one- and two-layer compacts by the EPD method from non-aqueous suspensions of nanopowders was studied. The use of acetylacetone and polyvinyl butyral (PVB) was shown to make it possible to obtain stable alcohol suspensions of the nanopowders characterized by high zeta potential values (+29…+80 mV) and to carry out a stable EPD process. One-layer compacts were made from the YLa and HoLa nanopowders with a density of 30–43%. It was found out that the introduction of PVB into the suspension leads to a decrease in the mass and thickness of the green bodies deposited, but does not significantly affect their density. A possibility to make two-layers (YLa/HoLa) compacts with a thickness of up to 2.6 mm and a density of up to 46% was demonstrated. Sintering such compacts in a vacuum at a temperature of 1750°C for 10 hours leads to the formation of ceramics with a homogeneous boundary between the YLa/HoLa layers and thickness of the interdiffused ions layer of about 30 μm.

Epidemics are the most common natural phenomena that have occurred throughout the entire history of human society. Depending on the type of disease and the development of the collective immunity that society had acquired by then, the consequences of epidemics were usually very severe. Precisely because of this, the aim of the paper is a scientific description of the way in which the prescribed preventive measures should be applied from the epidemiological, security, economic, legal and other aspects, so that the society, through the mechanisms of the state, can defend and rehabilitate the consequences of an epidemic of an infectious disease. Eliminating the epidemic's impacts is a very difficult issue. In particular, there is an infectious illness epidemic that is spreading uncontrolled throughout society on the one hand. In order to introduce a quarantine that restricts the epidemic's progress and, if the quarantine lasts long enough, to end the epidemic, contact between members of the social group must be broken. On the other side, the cessation of communication between members of a social group also signifies the cessation of all facets of life in that society, including economic ties, education, growth of culture, scientific research, etc.

The development of the automotive industry leads to the improvement of the designs of automatic transmissions and drives and to the development of methods for monitoring and diagnosing their condition. The trend of improving transmissions comes down mainly to the endless improvement of existing designs of CVTs and variators, which inevitably leads to the complication of designs and methods for their control and diagnostics.There is a need to create a fundamentally new simplified gearbox based on the scientific achievements of mechanics. However, the created structures remained inoperable due to the lack of theoretical justification.The adaptive gear variator developed by the author, which has CVT functions, is a mechanism with two degrees of freedom and with an additional constraint of a fundamentally new type, called a force - speed constraint. The force - speed constraint imposes a force restriction on the movement of links, while maintaining the number of degrees of freedom in the kinematics. Monitoring the state of the developed gearbox in the form of a non-switchable gear variator is greatly simplified, since the largest number of faults occur in the control system, and there is no control system in the gear variator. It seems possible to apply the digital twin method to diagnose the developed simplified CVT.The proposed article is devoted to a theoretical description of a fundamentally new adaptive gearbox, created on the basis of the latest achievements in mechanics, with the prospect of developing a simplified monitoring and diagnostic system for it

We investigate regular damped oscillatory structures appearing in the "effective" form factor of various hadrons. The behavior of this form factor can be extracted from the experimental information on total cross sections, the processes $\sigma_{tot}(e^+e^- \to h \bar h)$, $h=\pi^{\pm}, K^{\pm}, K^0, p, n $ are examined. The apparent oscillations have been observed for the first time for the proton and we show, taking also other hadrons into the consideration, that they are an arbitrary artifact resulting from a very simplistic theoretical description based on an elementary three-parametric model. If the data are described by a more appropriate and well physically funded U\&A model, then the oscillations disappear. In addition, if the simple model is used to describe the data, one observes that the oscillations are opposite for particles which form an isospin dublet. We show, by using the U\&A model, that this feature is explained by the transformation properties of the corresponding states in the isotopic space.

Failure of various weight-loss programs and long-term maintenance of favorable body composition in all kinds of people is high, since the majority go back to old dietary patterns. Many studies have documented the efficacy of a plant-based diet (PBD) for body mass management, but there are opinions that maintaining a PBD is difficult. We aimed to evaluate the long-term success of a whole-food plant-based (WFPB) lifestyle program. We investigated the differences in the obesity indices and lifestyle of 151 adults (39.6 ± SD 12.5 years), who were on our program for short (0.5–<2 years), medium (2–<5 years), or long term (5–10 years). Body-composition changes were favourable for all three groups, both genders and all participants. There were no differences in relative body-composition changes (BMI, body fat percentage and muscle mass index (MMI)) between the three groups. All participants improved their BMI (baseline mean pre-obesity BMI range (kg/m²): 26.4 ± 5.6 to normal 23.9 ± 3.8, p < 0.001), decreased body mass (–7.1 ± 8.3 kg, p < 0.001) and body fat percentage (–6.4 ± 5.6 % points, p < 0.001). Those with the highest BMI at baseline lost the most of: a) BMI units, b) total body mass and c) body fat (a) (kg/m²) (–5.6 ± SD 2.9, –2.4 ± 1.8 and –0.9 ± 1.5), b) (kg) (–16.1 ± SD 8.8, –7.1 ± 5.4 and –2.5 ± 4.5) and c) (% points) (–9.5 ± SD 5.7, –6.6 ± 4.6 and –4.7 ± 5.3) for participants who had baseline BMI in obese, overweight and normal range, respectively; p_{baseline vs. current} < 0.001 for all). 85.6% (101 out of 118) of parents of underage children (< 18 years), introduced WFPB lifestyle to their children. WFPB lifestyle program provides long-term lifestyle changes for reversal of obesity and is effective transferred to the next generation.

Positive invariant set is an important concept of dynamic systems. The purpose of this paper is to study the sufficient and necessary conditions that the set of ellipsoids and the Lorenz cone are positive invariant sets of discrete time systems. By means of nonlinear programming and induced norm, the problem of positive invariance is formulated as an optimization problem, and the equivalent dual form optimization is also presented using the dual optimization method. Our results provide more alternative methods for determining the positive invariance of quadratic form convex sets from the point of view of optimization and dual optimization. The effectiveness of this method is demonstrated by numerical examples.

In a 24-week-long experiment, 31 rats were assigned to one of 3 groups: a Control group receiving standard chow and water, a Fructose group receiving standard chow and a 20% fructose solution, or an STZ+lipids group that received a fat-enriched diet following a single 25 mg/kg streptozotocin injection at the onset of the diet. Both groups experienced significantly increased caloric intake but did not gain weight above the Control group level. Adipocytes in subcutaneous and visceral adipose depots of both groups had smaller size compared to control and higher density in tissue. Respirometric analyses unveiled a substantial increase in mitochondrial respiration across all adipose tissue types in both dietary intervention groups, with greater changes observed in the Fructose group. Correlation analyses demonstrated that in both experimental groups high tissue respiration is associated with better biochemical profile and closer to control adipose tissue morphology. Increased tissue respiration in adipose depots could be an important mechanism of resilience to excessive caloric intake.

This comparative study aims to investigate environmental awareness, knowledge, and safety among students in Montenegro and North Macedonia, considering the unique socio-cultural and environmental contexts of both countries. A mixed-methods approach involving surveys and interviews was employed to gather data from students in educational institutions across Montenegro and North Macedonia. The study assessed various factors, including students' awareness of environmental issues, their perceived level of knowledge, and their attitudes towards safety measures. A comprehensive series of 400 face-to-face interviews was carried out and these interviews encompassed 200 students from Montenegro and an equal number from North Macedonia, taking place at two esteemed academic institutions: The University of Montenegro in Podgorica and The University of St. Clement of Ohrid, Bitola, Republic of North Macedonia. Our hypothetical conceptual framework proposes that a combination of variables, including gender (H1), age (H2), year of study (H3), and rate of study (H4), significantly influences the attitudes of students from Montenegro and North Macedonia towards environmental awareness, safety, and knowledge. Research findings indicate significant variations in environmental awareness and knowledge perception among students in the two countries. While both Montenegro and North Macedonia face environmental challenges, differences in educational systems and socio-economic factors contribute to distinct attitudes and behaviors towards environmental issues and safety practices. This study sheds light on the importance of understanding regional differences in environmental awareness and knowledge perception among students. By identifying areas of strength and areas needing improvement, policymakers and educators can develop targeted interventions to enhance environmental education and foster a culture of sustainability in both Montenegro and North Macedonia.

The structural evolution and phase composition of multi-block thermoplastic polyurethanes, with different nature of the soft segments based on poly(butylene adipate) (PBA), were analyzed during in-situ thermal treatments. A combination of synchrotron small- and wide-angle X-ray scattering, differential scanning calorimetry, thermogravimetric analysis, and FTIR spectroscopy was used to determine the influence of macrodiol nature and crystallization conditions on the polymorphic behavior of PBA. Using a new synthesis scheme, a relatively high degree of crystallinity for urethane blocks was achieved, which depends on the diisocyanate type in the structure of the soft segment. The hard segment domains impose geometrical constraints on PBA, thereby altering its crystallization process compared to the neat oligomer. Thus, crystallization after annealing at a low temperature (80 °C) is fast, predominantly yielding a metastable β-phase. When heated to 180 °C, which is higher than the hard-segment melting temperature, a phase-separated structure is observed. Subsequent crystallization is slower, favoring the formation of the stable α-PBA modification. The phase separation can be observed even after the hard block melting. A notably slow crystallization from an isotropic melt was documented after the disruption of phase separation at 230 °C.

Characterized in biomedical terms, stretching exercises have been defined as movements applied by external and/or internal forces – to increase muscle and joint flexibility, decrease muscle stiffness, to elevate joint range of motion (ROM), to increase the length of the morpho-functional unit “muscle-tendon”, to improve joint, muscle and tendon movements, contraction and relaxa-tion. The present review examines and summarizes the initial and recent literature data related to the biomechanical, physiological and therapeutic effects of static stretching (SS) on flexibility and other physiological characteristics of the main structural and functional unit “joint-ligaments-tendon-muscle”. The healing and therapeutic effects of SS, soon combined with other rehabilitation techniques (massage, foam rolling – with and without vibrations; hot/cold therapy, etc.) are discussed in relationship to creation of individual (patient-specific) or group programs for treatment and prevention of joint injuries as well as for improving performance in sports. From a theoretical point of view, the role of SS as positively affecting the composition of the connective tissue matrix is pointed out: type I-III collagen synthesis, hyaluronic acid and glucosaminoglycans (GAGs) turnover – under influence of the transforming growth factor beta-1 (TGF-β-1). Different variables as collagen type, biochemistry, elongation and elasticity are used as molecular biomarkers. Recent studies evaluated that the static progressive stretching therapy could prevent/reduce the development of arthrogenic contractures, joint capsule fibrosis, muscle stiffness and need new clinical applications. Combined stretch techniques are proposed and ap-plied in medicine and sports, depending on their long- and short-term effects on variables such as ROM, EMG activity, muscle stiffness, etc. The results obtained are of theoretical and practical interest for development of new experimental, mathematical and computational models and creation of efficient therapeutic programs. The healing SS effects on the main structural and functional unit – “joint-ligament-tendon-muscle” need further investigations, which could clarify and evaluate benefits of SS in prophylaxis and treatment of joint injuries - in healthy and ill in-dividuals, in older adults, as compared to young, active and well-trained persons, as well as to professional athletes.

The deregulated markets have replaced the traditional way of trading electricity from the producers to the consumer, via government-owned organizations and regulated tariffs. Nowadays, electricity prices are determined by the offer-demand mechanism and consumers can negotiate tariffs with their supplier of choice. For classic wholesale suppliers, the tariffs are a result of the transactions performed on the wholesale market and the energy mix available in certain geographical regions. In parallel with becoming eligible and participating in retail electricity markets, the consumers use increasingly local generation sources based mostly on renewable energy technologies such as PV panels, and become prosumers. They want to be able to sell back to the market the generation surplus, in order to obtain the maximum benefits from their initial investment. Currently, several trading mechanisms for prosumers are available, ranging from the simplest, selling back the surplus to an aggregator at fixed tariffs, to more complex market schemes. This paper proposed a two-tier local market model for prosumers and consumers connected in microgrids, based on the blockchain technologies and other technologies and concepts such as remote sensing, smart grids, crowdsourcing and energy poverty.

The deregulated markets have replaced the traditional way of trading electricity from the producers to the consumer, via government-owned organizations and regulated tariffs. Nowadays, electricity prices are determined by the offer-demand mechanism and consumers can negotiate tariffs with their supplier of choice. For classic wholesale suppliers, the tariffs are a result of the transactions performed on the wholesale market and the energy mix available in certain geographical regions. In parallel with becoming eligible and participating in retail electricity markets, the consumers use increasingly local generation sources based mostly on renewable energy technologies such as PV panels, and become prosumers. They want to be able to sell back to the market the generation surplus, in order to obtain the maximum benefits from their initial investment. Currently, several trading mechanisms for prosumers are available, ranging from the simplest, selling back the surplus to an aggregator at fixed tariffs, to more complex market schemes. This paper proposed a two-tier local market model for prosumers and consumers connected in microgrids, based on the blockchain technologies and other technologies and concepts such as remote sensing, smart grids, crowdsourcing and energy poverty.

Emerging of mass-spectroscopy with inductively-coupled plasma (ICP-MS) made possible to study the microelement composition of crude oil and its derivatives (with the limit of detection at the ppt level). We have studied the crude oil composition of some West Siberian and Tatarstan oilfields with the ICP-MS method to detect 50 rare, rare-earth, and other microelements. The elemental composition is reasonably comparable to their concentrations in ultrabasites whereas the contents of most of the elements are low to the limit. On the diagrams of rare-earth elements, one can see the prevalence of light lanthanides and positive europium anomaly. The study shows that crude oils have a specific microelement composition that stands out from other geological systems.

The gravel road pavement has a lower construction cost but poorer performance than the asphalt surface. It also emits dust and deforms under the impact of vehicle loads and ambient air factors. The resulting ripples and ruts are constantly deepening, increasing vehicle vibrations and fuel consumption, reducing safe driving speed and comfort. In this article, existing pavement quality evaluation indexes are analysed, and a methodology for their adaptation for roads with gravel pavement is proposed. This article reports the measured wave depth and length of the gravel pavement profile by the straightedge method of a 160 m long road section in three road exploitation stages. The measured pavement elevation was processed according to ISO 8608, and vehicle frequency response has been investigated using simulations in MATLAB/Simulink. The applied International Roughness Index (IRI) analysis showed that a speed of 30-45 km/h instead of 80 km/h provides the objective results of IRI calculation on the flexible pavement due to a decreasing velocity of vehicle's unsprung mass on a more deteriorated road pavement state. The influence of the corrugation phenomenon of gravel pavement has been explored, identifying specific driving safety and comfort cases. Finally, an increase in the Dynamic Load Coefficient (DLC) at a low speed of 30 km/h on the most deteriorated pavement and a high speed of 90 km/h on the middle-quality pavement demonstrates the demand for timely gravel pavement maintenance and the complicated prediction of a safe driving speed for drivers.

Accidents at mining enterprises, including tailing dumps, pose significant threats to human lives, structures, and the environment. This study focuses on designing, constructing, and operating tailing dumps in Siberia's northern region. To ensure safety and minimize environmental impacts, comprehensive scientific monitoring and research were conducted at all stages, including design, construction, operation, and disposal. The aim was to create a uniform mass within the dam body, requiring understanding of the tailings' structure and technological characteristics during placement. Parameters like particle size, distribution, density, and moisture content were considered to assess tailings' physical and geometric properties. Estimated monitoring was introduced as a permanent model to quickly assess the stability of hydrotechnical constructions. This involved monitoring changes in exploitation properties, structure height, beach length, and water levels. A controlled inwashing technology for subsequent dam layers was developed. Complex research facilitated the formulation of an estimated monitoring methodology and an algorithm for tailing dam formation. Practical application demonstrated high reliability and confirmed load-bearing capacity, allowing for the forecast of dam stability and safe execution. Findings led to alterations in work techniques, ensuring safe and efficient operation of tailing dams.

Effect of wireworm-damaged lettuce roots on antioxidative defence system (ascorbate-glutathione cycle, photosynthetic pigments) and movement of insect/slug parasitic nematodes towards determined root exudates was studied in a glasshouse experiment. Lettuce seedlings were grown in a substrate soil in the absence/presence of wireworms (Elateridae). Determination of antioxidants and photosynthetic pigments were analysed. Volatile organic compounds (VOC) emitted from lettuce roots were investigated by GC-MS. Herbivore induced root compounds, namely 2,4-nonadienal, glutathione and ascorbic acid, were selected for a chemotaxis assay with nematodes Steinernema feltiae, S. carpocapsae, Heterorhabditis bacteriophora, P. papillosa, and O. myriophilus. Root pests negatively affected photosynthetic pigment contents even before the appearance of visible symptoms, as protective pigments responded to the presence of reactive oxygene species (ROS). Using lettuce as a model plant, we recognised ascorbate-glutathione system as a redox hub in defense response against wireworms and analysed its role in root-exudate mediated chemotaxis of nematodes. Infected plants also demostrated increased levels of volatile 2,4-nonadienal. Entomopathogenic nematodes (EPNs, S. feltiae, S. carpocapsae, and H. bacteriophora) proved to be more mobile than parasitic nematodes O. myriophilus and P. papillosa towards chemotaxis compounds. Among them 2,4 – nonadienal repelled all tested nematodes. Most exudates that are involved in belowground tritrophic interactions remain unknown but an increasing effort is being made in this field of research. Understanding more of these complex interactions would not only allow a better understanding of the rhizosphere but could also offer ecologically sound alternatives in pest management of agricultural systems.

Soil organic carbon (SOC) is an essential condition for soil health and a potential sink for greenhouse gases. SOC dynamics in a long-term field experiment with mineral and organic fertilization on loamy sand Podzol in Vladimir Region, Russia, was traced with the dynamic carbon model RothC since 1968 until the present time. During this period, C stock increased 21% compared with the initial level in the treatment with the application of manure in an average annual rate of 10 t·ha-1. The model was also used to forecast SOC changes until 2090 for two contrasting RCP4.5 and RCP8.5 climatic scenarios. Until 2090, the steady growth of SOC stocks is expected in all compared treatments for both climate scenarios. This rate of growth was the highest until 2040, decreased in 2040-2070 and increased again in 2070-2090 for RCP4.5. The highest annual gain was within 21-27‰ under RCP4.5 and 16-21‰ in 2020-2040 in 0-20 cm soil layer. The expected accumulation of C allows increasing current C stock 1.6-1.7 times for RCP4.5 and 2.0-2.2 times for RCP8.5 scenario. Modelling demonstrated potentially more favourable conditions for SOC stability in arable Podzols than in Retisols in Central Russia in the 21st century.

Soil organic carbon (SOC) sequestration in arable soils is a challenging goal for soil management. Multiple factors should be considered for the prediction of the soil capacity to fix atmospheric carbon. In this study, we focused on the effect of crop rotation and previous land use for future carbon sequestration on two experimental fields with identical soils (Retisols) and input of organic fertilizers. We analyzed the SOC dynamics and used the Roth C model to forecast SOC changes under RCP4.5 and RCP8.5 scenarios. Our experimental and modelling results indicated a consistent increase in SOC stocks and the stable fractions of soil organic matter (SOM). The increase in SOC was higher in the experiment with the crop-grassland rotation that in the experiment with a rotation of row crops and barley. With similar total SOC stocks, the efficiency of soil management differed as reflected by the contrasting composition of SOM, as fields with a long cultivation history showed higher SOM stability. The goal of 4‰ annual increase of SOC stocks may be reached under crop- grassland rotation in 2020-40 and 2080-90 when applying mineral or organic fertilizer system for scenario RCP4.5, and mineral fertilizer system in 2080-2090 for scenario RCP8.5.

Background: Despite the fact that bone reconstructive surgeries are widely practiced worldwide, the search for an ideal bone replacement matetrial is still an open issue. We aimed to provide an overview of the current status of research and developments in this field with a focus on sapphire materials; Methods: A literature search and review was conducted using the PubMed, Scopus, and Embase databases. We searched for literature using the following keywords: bone implants; biocompatible materials; bone replacement material; sapphire implants; Results: Sapphire has a unique combination of mechanical, physical and chemical characteristics thanks to wich it has an excelent biocompatability and biointegrity.Unlike other materials it is incredibly strong and has a high endurance. The successful experience of using this material in medical instrument engineering, dentistry and cardiac surgery shows its benefits; Conclusions: We consider that sapphire is a perspective material for bone replacement implants and researchers should look in this direction.

We offered the circuit of a discrete analog filter (DAF) low frequencies of second-order on switchable capacitors, which differs from the known ones in that three capacitors with one terminal are connected to a common bus, and the frequency of the DAF pole depends not only on the ratio of the capacitances of the frequency-setting capacitors, but also on the ratio of resistances two additional resistors in the feedback. This allows at constant values ​​of the capacitances and a fixed switching frequency of electronic switches, control the pole frequency by changing the resistance ratio of additional resistors. Computer simulation of the developed circuit was performed in the Micro-Cap environment. It has been established that the DAF has a transmission coefficient close to minus one at very low frequencies and a transmission coefficient close to zero at higher frequencies.

Transmission electron microscopy methods were used to analyze the cementite substructure in the head of special-purpose long rails of DT400IK category made of hypereutectoid steel after long-term operation on an experimental track on the Russian Railways ring (the passed tonnage is 187 million tonnes). It is noted that the study of various aspects of cementite – its structure, morphology, chemical composition, crystal lattice defects is relevant. The steel structure is represented by three morphological components at a distance of 10 mm from the sample surface: lamellar perlite, fractured and fragmented perlite. The volume fraction of lamellar perlite in the material is 65%. It is shown that after operation, the cementite plates are bent and separated by ferrite bridges. In the plates of ferrite and cementite, a dislocation substructure is formed which is of chaotically distributed and network type in ferrite and of ordered type in cementite. An increased density of dislocations at ferrite-cementite interfaces compared to the volume of ferrite plates was noted. Two possible mechanisms of deformation transformation of lamellar perlite grains are indicated: fracture of cementite plates and carbon pulling out from the lattice of the carbide phase. It is indicated that in the dissolution of cementite plates, the interfacial boundaries “α-phase-cementite” play an important role. The removal of carbon from cementite plates occurs most intensively near defects in ferrite and cementite. The formed nanosized particles of tertiary cementite are unevenly distributed in the ferrite plates, most of them are observed at the locations of ferrite subgrains and interfacial boundaries. This results in non-uniform diffraction contrast in dark-field images of cementite plates. Nanosized particles of cementite can be taken out into the interlamellar space of pearlite colonies in the process of dislocation slip, or they are formed as a result of deformation decomposition, which is less likely. Fragmentation of ferrite and cementite plates is revealed and azimuthal components of total misorientation angles are estimated. The mechanisms of mass transfer of carbon atoms over interstitial sites, deformation vacancies, dislocation tubes, grain boundaries and fragments are considered. According to all the established patterns of the cementite substructure transformation, a comparison with the results for rails made of hypoeutectoid steel was performed.

Grid refinement is used to save computing costs while preserving high precision of fluid simulation. In the Lattice Boltzmann Method, grid refinement often uses interpolated values. We found a method, where interpolation in space and time is not required. For this purpose, we used the moment matching condition and rescaling the non-equilibrium part of populations, and developed the recalibration procedure that allows to transfer information between different LBM stencils in the simulation domain. Then, we build non-uniform lattice which uses stencils with different shapes on the transition. The resulting procedure is verified on the 2D Poisselle flow and the advected vortex benchmark. In prospect, grids with adaptive geometry can be built with the use of the proposed method.

The interaction of human immunodeficiency virus with human cells is responsible for all stages of the viral life cycle, from the infection of CD4+ cells to reverse transcription, integration, and the assembly of new viral particles. To date, a large amount of OMICs data as well as information from functional genomics screenings regarding the HIV-1-host interaction has been accumulated in the literature and in public databases. We processed databases containing HIV-host interactions and found 2910 HIV-1-human protein-protein interactions, mostly related to viral group M subtype B, 137 interactions between human and HIV-1 coding and non-coding RNAs, essential for viral lifecycle and cell defense mechanisms, 232 transcriptomics, 27 proteomics, and 34 epigenomics HIV-related experiments. Numerous studies regarding network-based analysis of corresponding OMICs data have been published in recent years. We overview various types of molecular networks, which can be created using OMICs data, including HIV-human protein-protein interaction networks, co-expression networks, gene regulatory and signaling networks, and approaches for the analysis of their topology and dynamics. The network-based analysis can be used to determine the critical pathways and key proteins involved in the HIV life cycle, cellular and immune responses to infection, viral escape from host defense mechanisms, and mechanisms mediating different susceptibility of humans to infection. The proteins and pathways identified in these studies may represent a basis for developing new anti-HIV therapeutic strategies such as new small-molecule drugs preventing infection of CD4+ cells and viral replication, effective vaccines, "shock and kill" and "block and lock" approaches to cure latent infection.

This paper discusses approaches to the numerical integration of the coupled nonlinear Schrödinger equations system in case of few-mode wave propagation. The wave propagation assumes the propagation of up to nine modes of light in an optical fiber. In this case, the light propagation is described by the non-linear coupled Schrödinger equation system, where propagation of each mode is described by own Schrödinger equation with other modes interactions. In this case, the non-linear coupled Schrödinger equation system solving becomes increasingly complex, because each mode affects the propagation of other modes. The suggested solution is based on the direct numerical integration approach, which is based on a finite-difference integration scheme. The well-known explicit finite-difference integration scheme approach fails, due to the non-stability of the computing scheme. Due to this fact, the combined explicit/implicit finite-difference integration scheme, based on the implicit Crank–Nicolson finite-difference scheme, is used. It allows ensuring the stability of the computing scheme. Moreover, this approach allows separating the whole equation system on the independent equation system for each wave mode at each integration step. Additionally, the algorithm of numerical solution refining at each step and the integration method with automatic integration step selection are used. The suggested approach has performance gains (or resolutions) up to three or more orders of magnitude in comparison with the split-step Fourier method due to the fact that there is no need to produce direct and inverse Fourier transforms at each integration step. The main advantage of the proposed method is the ability to calculate the propagation of an arbitrary number of modes in the fiber.

One of the modern methods of improving operating characteristics of titanium and titanium-based alloys under conditions of friction and increased contact loads is the method of ion-plasma nitriding. The effect of nitriding of VT5 alloy (Al 4,5-6,7 %, V to 1,2 %, Mo to 0,8 % − analogue 3.7115) in the plasma of a glow discharge excited in a hollow cathode on its tribological characteristics in pairs with different materials in T-1 fuel and under dry friction conditions has been studied. For research and tribological tests, samples of VT5 alloy were nitrided in the plasma of a glow discharge excited in a hollow cathode at a temperature of 975 ± 15°C and a pressure of 58 ± 2 PA in a nitrogen-argon gas mixture with a nitrogen content of 78 %. Studies of samples of VT5 alloy after nitriding showed that the surface roughness Ra was in the range of 0.58-0.64, and the surface hardness HV5 was 525 ± 20 kgf/mm² at a base hardness of 325 ± 15 kgf/mm². Tribological tests were performed on a friction machine 2070 SMT-1 according to the scheme "cube - roller". Tests under conditions of friction with oil were performed at a load of 200 N. The sliding speed during the tests was 1.3 m/s, the test time was 75 sec. The test under dry friction conditions was carried out at a load of 100 N and a sliding speed of 0.785 m/s, the test time was 30 minutes. Low wear ability in relation to the nitrided titanium alloy VT5 (<2.4x10^-4 mm³/s), as well as friction coefficients at the level of 0.08 to 0.12 in the order of their growth had bronze VB-23NTS (Pd 18–22 %, Ni 3–4 %, Zn 3–4 %, Sb 3–4 %, P 0.15–0.3) r.O10C2N3, VB-24 (Sb 4.7–6, 2 %, P 0.4–0.9), steel 1.3505, cast iron GGG80, cemented steel 20Cr3MoWV.

The Pannonian basin major heat system in Central Europe. Their peripheral basins like the East Slovakian basin is a example of a geothermal structure with a linear directed heat flow ranging from 90 to 100 mW /m2 from west to east. However, the use of the geothermal source is limited by several critical tectono-geologic factors: (a) tectonics, and the associated disintegration of the aquifer block by multiple deformations during the pre-Paleogene mainly Miocene period. The main discontinuities of NW-SE and N-S direction negatively affect the permeability of the environment. On the contrary, for utilization are important the secondary minor NE-SW dilatation open fractures which have developed by sinistral transtension on N–S faults and accelerated normal movements to the southeast in the present. (b) hydrogeological conditions, the geothermal structure accommodated three water types, namely Na-HCO3 with 10.9 g.l-1 mineralization (in the north), the Ca-Mg-HCO3 with 0.5 – 4.5 g.l-1 mineralization (in the west), and Na-Cl water type containing 26.8-33.4 g.l-1 (in the southwest) mineralization. The chemical composition is influenced by the Middle Triassic dolomites aquifer as well as by infiltration of saline solutions and meteoric waters along open fractures/faults. (c) geothermally anomalous heat 123 – 129 °C close to volcanic chain with 170 l/s total flow seems to be the perspective for heat production.

Growing potato demands considerable external inputs of pesticides due to its susceptibility to various pests and pathogens. Here we present an attempt to differentiate the Slovak rural landscape with respect to the possibility of effective potato cultivation and to characterise soil parameters of current potato cultivation areas with the aim to increase the sustainability of the potato production. The selection was based on soil climatic, production and economic parameters. By using the GIS tools and existing databases on soil characteristics in Slovakia, maps of soil suitability categories for potato cultivation were generated. In Slovakia, it was found that 12.3% of farmland is very suitable for potato cultivation and that as much as 43.1% is not suitable. Later the specified categories were characterised in detail and specified with respect to geographic, soil, climatic, production and economic parameters. Currently, most potato crops are cultivated on Eutric Cambisols (27%), Chernozems (20%) and Mollic Fluvisols (18%). Loamy soils (65%), soils without gravel (62%), deep soils (74%) and soil situated on plains (55%) are dominant in these regions. We suggest that potato cultivation should be concentrated on the most suitable areas, thereby increasing the economic profitability, improving the ecological stability of the country and supporting the sustainability of the agriculture.

Four-wire low voltage microgrids supply one-phase consumers with continuously changing electricity demand. For addressing climate change concerns, governments implemented incentive schemes for residential consumers, encouraging the installation of home PV panels for covering self-consumption needs. In the absence of sufficient storage capacities, the surplus is sold back by these entities, called prosumers, to the grid operator or in local markets, to other consumers. While these initiatives encourage the proliferation of green energy resources, and ample research is dedicated to local market designs for prosumer-consumer trading, the main concern of distribution network operators is the influence of power flows generated by prosumer surplus injection on the operating states of microgrids. The change in power flow amount and direction can greatly influence the economic and technical operating conditions of radial grids. This paper proposes a metaheuristic algorithm for prosumer surplus management that optimizes the power surplus injections using the automated control of three-phase inverters, with the aim of improving the active power losses and balancing the phase voltage profiles. A case study is performed on two real distribution networks with distinct layouts and load profiles and the algorithm shows its efficiency in both scenarios.

A growing number of households benefit from the government subsidies to install renewable generation facilities such as PV panels, used to gain independence from the grid and provide cheap energy. In the Romanian electricity market, these prosumers can sell their generation surplus only at regulated prices, back to the grid. A way to increase the number of prosumers is to allow them to make higher profit by selling this surplus back into the local network. This would also be an advantage for the consumers, who could pay less for electricity exempt from network tariffs and benefitting from lower prices resulting from the competition between prosumers. One way of enabling this type of trade is to use peer-to-peer contracts traded in local markets, run at microgrid (μG) level. This paper presents a new trading platform based on smart peer-to-peer (P2P) contracts for prosumers energy surplus trading in a real local microgrid. Several trading scenarios are proposed, which give the possibility to perform trading based on participants’ locations, instantaneous active power demand, maximum daily energy demand and the principle of first come first served implemented in an anonymous blockchain trading ledger. The developed scheme is tested on a low-voltage (LV) microgrid model to check its feasibility of deployment in a real network. A comparative analysis between the proposed scenarios, regarding traded quatities and financial benefits is performed.

Experimental studies on the development of processes of obtaining ultradispersed metal-ceramic materials and coatings Mo-ZrO₂, Mo-Al₂O₃, W-ZrO₂, W-Al₂O₃ CVD by deposition from the gas phase in CO₂ process using low-temperature nonequilibrium plasma were carried out.The structure, microhardness, phase composition, and high-temperature annealing behavior of the materials were studied. It is shown that the choice of parameters of the deposition process and temperature annealing can be controlled by the distribution function of ultradispersed particles in the material and their sizes.High-temperature X-ray studies of "molecular" two-phase alloys Mo- Al₂O₃ and Mo- ZrO₂show that, depending on the elastic and thermal properties of the matrix materials and dispersed particles, the molybdenum matrix can be in an all-round tensed or all-round compressed state.In the study of the electro-physical characteristics of the two-phase disperse-strengthened alloys Mo- ZrO₂, Mo- Al₂O₃, W- ZrO₂, W- Al₂O₃ it has been established that in the region of temperatures 1023...1273K anomalous changes of specific electrical resistance and instability of thermal eddy in magnitude are observed apparently connected with the presence of internal stresses in material caused by ultradisperse particles.Theoretical aspects of the problem of increasing the carriers density in nanocomposite materials are reviewedTheoretical analysis of the effect of the ensemble of microparticles on the change of electron density in ultradisperse metal-ceramic materials is carried out. It is shown that the average values of the electron density in the matrix with the introduction of 1% of particles with a radius of 50 A increase by more than two orders of magnitude.The possibilities of creating ultradisperse compositions using radiation-plasma methods are considered.

Bottlebrush (BB) elastomers with water-soluble side chains and tissue-mimetic mechanical properties are promising for biomedical applications like tissue implants and drug depots. This work investigates the microstructure and phase transitions of BB elastomers with crystallizable polyethylene oxide (PEO) side chains by real-time synchrotron X-ray scattering. In the melt, the elastomers exhibit the characteristic BB peak corresponding to the backbone-to-backbone correlation. Upon crystallization of the side chains, the intensity of the peak decays linearly with crystallinity, and eventually vanishes due to BB packing disordering within intercrystalline amorphous gaps. This behavior of the bottlebrush peak differs from an earlier study of BBs with poly(ε-caprolactone) side chains, explained by stronger backbone confinement in the case of PEO, a high-crystallinity polymer. Microstructural models based on 1D SAXS correlation function analysis suggest crystalline lamellae of PEO side chains separated by amorphous gaps of monolayer-like BB backbones.

We employ hierarchy of models (HoM) with 2, 3 and 4 parameters to reanalyze the nucleation kinetics in the electrodeposition as quantified by n(t) - “the number of nuclei vs. time” data obtained at different overvoltages from precise experiments on electrodeposition of Hg on two different types of Pt-cathodes by Ivan V. Markov and Evgenia Stoycheva [1]. The obtained two scales, nmax and , are used to rescale the original data mapping it on a master curve in coordinates . Our main result is obtained by studying further the dependence of these two scales on the overvoltage (analogue of supersaturation). Surprisingly, for one of the two cathode types - the “hemispherical single-crystal electrode” (as defined by the authors), there is discontinuity in the “ vs. overvoltage” dependence – an almost horizontal jump from 85 to 86 mV accompanied by a change in the slope of the dependence - it is ~ -1 and ~ -0.5 after. For the other cathode - “plane structureless platinum electrode”,  decreases smoothly. Combined, these two behaviors point at the so called “cusp catastrophe”. We compare our findings with published results on protein nucleation.

Papain-like protease PLpro, a domain within a large polyfunctional protein nsp3, plays key roles in the life cycle of SARS-CoV-2, being responsible for the first events of cleavage of a polyprotein into individual proteins (nsp1-4) as well as for the suppression of cellular immunity. Here, we developed a new genetically encoded fluorescent sensor, named PLpro-ERNuc, for detection of PLpro activity in living cells using translocation-based readout. The sensor was designed as follows. A fragment of nsp3 protein was used to direct the sensor on the cytoplasmic surface of endoplasmic reticulum (ER) membrane, thus closely mimicking the natural target of PLpro. The fluorescent part included two bright fluorescent proteins - red mScarlet I and green mNeonGreen, separated by a linker with the PLpro cleavage site. Nuclear localization signal (NLS) was attached to ensure accumulation of mNeonGreen into the nucleus upon cleavage. We tested PLpro-ERNuc in the model of recombinant PLpro expressed in HeLa cells. The sensor demonstrated expected cytoplasmic reticular network in the red and green channels in the absence of protease, and efficient translocation of the green signal into nuclei in the PLpro-expressing cells (14-fold increase of the nucleus/cytoplasm ratio). Then, we used PLpro-ERNuc in the model of Huh7.5 cells infected with SARS-CoV-2 virus, where it showed robust ER-to-nucleus translocation of the green signal in the infected cells 24 h post infection. We believe that PLpro-ERNuc represents a useful tool for screening PLpro inhibitors as well as for monitoring virus spread in a culture.

As the problem of traction injuries to brachial plexus is a common one and of high socio-economic significance, the analysis of the surgical outcomes in patients with this pathology is significant for neurosurgery, neurology, traumatology-orthopedics, and rehabilitation. The aim of the research is to compare the short-term outcomes of using various surgical methods for managing patients with closed traction injuries of brachial plexus. Material and methods. The research involved 61 patients with closed traction injury of brachial plexus divided into two groups homogeneous in sex, age and severity of their neurological deficit: Group I – 33 patients who underwent microsurgical neurolysis, Group II – 28 patients who underwent microsurgical neurolysis combined with one-level electrostimulation. The dynamic assessment of clinical and functional status of upper limbs was performed using scale methods and electrophysiological monitoring. Results. The research revealed a more evident recovery of the upper limb function in Group II patients suggesting the method of microsurgical neurolysis combined with electrostimulation to be preferable in case of closed traction injuries to brachial plexus. Conclusion. The combination of microsurgical neurolysis with one-level electrostimulation improves the short-term outcomes of surgical treatment in patients with closed traction injuries of brachial plexus due to a sooner decrease in pain in postoperative period, and positive dynamics of clinical and electrophysiological parameters.

The main goal of this paper is to present results of preliminary archaeological research on the south side of Lake Issyk-Kul in Kyrgyzstan. We test the hypothesis that agropastoral land use changed over four millennia from the Bronze Age through the ethnographic Kirghiz period due to economic, socio-political, and religious changes in the prehistoric and historic societies of this region. Our research objectives are to: (1) describe and analyze survey results from Lower Kizil Suu Valley; (2) discuss the results of radiometric and archaeobotanical samples taken from three stratigraphic profiles from three settlements from the Juuku Valley, including these chronological periods: the Wusun period (200 to 400 CE), the Qarakhanid period (1100 to 1200 CE), and the ethnographic Kirghiz period (1700 to 1900 CE); and (3) conduct preliminary GIS spatial analyses on the Iron Age mortuary remains (Saka and Wusun period). This research emerges out of the first archaeological surveys conducted in 2019 - 2021 and includes the Lower Kizil Suu alluvial fan; it is an initial step toward developing a model for agropastoral land use for upland valleys of the Inner Tian Shan Mountains.

Abstract: CRISPR/Cas systems are used for genome editing, both in basic science and in bio-technology. At the same time, CRISPR/Cas editors have several limitations, including insufficient specificity leading to "off-targets" and the dependence of activity on chromatin state. A number of highly specific Cas9 variants have been obtained now, but most of them are characterized by reduced activity on eukaryotic chromatin. We identified a spatial cluster of amino acid residues in the PAM-recognizing domain of Streptococcus pyogenes Cas9, whose mutations restore the activity of one of the highly specific forms of SpyCas9 without reducing its activity in Saccharomyces cere-visiae. In addition, one of these new mutations also increases the efficiency of SpyCas9-mediated editing of a site localized on the stable nucleosome. The improved Cas9 variants we obtained, which are capable of editing hard-to-reach regions of the yeast genome, may help in both basic research and yeast biotechnological applications.

High average power narrow-linewidth tunable solid-state lasers in the wavelength region between 2 to 3 μm are attractive light sources for many applications. This paper reports a narrow-linewidth widely-tunable laser system based on the polycrystalline Cr2+:ZnSe elements pumped by the repetitively-pulsed 2.1 µm Ho3+:YAG laser operating at the tens of kilohertz pulse rate. An advanced procedure of ZnSe-element doping and surface improvement was applied to increase the laser-induced damage threshold, which resulted in an increase of the output power of the Cr2+:ZnSe laser system. The high-average-power laser system comprised double master-oscillators and power amplifiers: Ho3+:YAG and Cr2+:ZnSe laser oscillators, and Ho3+:YAG and Cr2+:ZnSe power amplifiers. The output wavelength was widely tuned within 2.3-2.7 µm by an acousto-optical tunable filter inside the Cr2+:ZnSe master oscillator cavity. The narrow-linewidth operation at the pulse repetition rate of 20-40 kHz in a high-quality beam with the average output power up to 9.7 W was demonstrated.

In this study, we investigated the features of co-infection with SARS-CoV-2 and nonpathogenic strain LEV8 of coxsackievirus A7 or enterovirus A71 for Vero E6 cells and Syrian hamsters. The investigation of co-infection with SARS-СoV-2 and LEV-8 or EV-A71 in the cell model was shown that a competitive inhibitory effect for these viruses were especially significant against SARS-CoV-2. Pre-infection with enteroviruses in animals caused more than a 100-fold decrease in the levels of SARS-CoV-2 virus replication in the respiratory tracts and more rapid clearance of the lower respiratory tract from infectious SARS-CoV-2. Co-infection with SARS-CoV-2 and LEV-8 or EV-A71 also reduced the severity of clinical manifestations of the SARS-CoV-2 infection for animals. Additionally, the histological data illustrated that co-infection with nonpathogenic coxsackievirus decreased the level of pathological changes by SARS-CoV-2 in the lungs. Research into the chemokine/cytokine profile demonstrated that the studied enteroviruses efficiently triggered this part of antiviral immune response, which can be associated with significant inhibition of SARS-CoV-2 infection. These results demonstrate that there exists a strong viral interference between the studied nonpathogenic strain of coxsackievirus A7 or enteroviruses A71 and SARS-CoV-2 pathogenic for humans in vitro and in vivo.

Early identification of viruses leads to more efficient disease management and control, and is extremely important. A possible new approach for creating virus sensors is the Electromagnetic echo effect (EMEE). An important feature is that the signal from EMEE is highly dependent on the state of the irradiated body. This makes it possible to control ongoing reactions, even if these reactions are invisible to the human eye or other equipment. This article shows the possibility of registering reaction occurring in the presence of an avian coronavirus causing infectious bronchitis, strain Massachusetts. The same methodology can be applied for other types of viruses as well.

Atmospheric correction is a necessary step in image processing data and spectra recorded by spaceborne sensors for pure cloudless atmosphere, primarily in the visible and near-IR spectral range. We have present a fast and sufficiently accurate method of atmospheric correction based on the proposed analytical solutions describing with high accuracy the spectrum of outgoing radiation at the top boundary of the cloudless atmosphere. This technique includes the model of the atmosphere and its optical parameters that are important in terms of radiation transfer. The solution of the inverse problem for finding unknown parameters of the model is carried out by the method of non-linear least squares (Levenberg-Marquardt algorithm) for an individual selected pixel of the image (its spectrum), taking into account the adjacency effects. Using the found parameters of the atmosphere and the average surface albedo, assuming homogeneity of the atmosphere within a certain area of the hyperspectral image (or the whole frame), the spectral albedo at the Earth's surface is calculated for all other pixels. It is essential that the procedure of the numerical simulation with non-linear least squares of the direct transfer problem is based on using analytical solutions, which provides a very short calculation time of the atmospheric parameters (seconds or less) and the ability to perform atmospheric correction "on-fly." Testing methods of atmospheric correction was performed using the synthetic outgoing radiation spectra at the top of the atmosphere (TOA), obtained by numerical simulation in the LibRadTran code, as well as spectra of real space images of the Hyperion hyperspectrometer. A comparison with the results of atmospheric correction in module FLAASH of ENVI package has been performed. Finally, to validate our data obtained by the SHARK method, a comparative analysis with ground-based measurements of Radiometric Calibration Network (RadCalNet) was carried out.

Analysis of 1382 measures of battery State of Health (SoH) from 283 Nissan Leafs (“Leaf/s”), manufactured between 2011 and 2017, has detected a faster rate of decline in this measure of energy-holding capacity for 30 kWh variants. At two years of age, the mean rate of decline of SoH of 30 kWh Leafs was 9.9% per annum (95% uncertainty interval of 8.7% to 11.1%; n = 82). This was around three times the rate of decline of 24 kWh Leafs which at two years averaged 3.1% per annum (95% uncertainty interval of 2.9% to 3.3%; n = 201). For both variants there was evidence for an increasing rate of decline as they aged, although this was much more pronounced in the 30 kWh Leafs. Higher use of rapid DC charging was associated with a small decrease in SoH. Additionally, while 24 kWh cars with greater distances travelled showed a higher SoH, in 30 kWh cars there was a reduction in SoH observed in cars that had travelled further. The 30 kWh Leafs sourced from United Kingdom showed slower initial decline than those from Japan, but the rate of decline was similar at two years of age. Improvements in the battery health diagnostics, continuous monitoring of battery temperatures and state of charge, and verification of a fundamental model of battery health are needed before causes and remedies for the observed decline can be pinpointed. If the high rate of decline in battery capacity that we observed in the first 2.3 years of a 30 kWh Leaf’s lifetime were to continue, the financial and environmental benefits of this model may be significantly eroded. Despite 30 kWh Leafs accounting for only 14% of all light battery electric vehicles registered for use on New Zealand roads at the end of February 2018, there is also the potential for the relatively poor performance of this specific model to undermine electric vehicle uptake more generally unless remedies can be found.

Thermal expansion of four alkaline-earth borates, namely Ca3B2O6 (0D), CaB2O4 (1D), Sr3B14O24 (2D) and CaB4O7 (3D), have been studied by in situ high-temperature powder X-ray diffraction (HTXRD). Strong anisotropy of thermal expansion is observed for the structures of Ca3B2O6 (0D) and CaB2O4 (1D) built up from BO3 triangles only: these borates exhibit the maximal expansion perpendicular to the BO3 plane, i.e. along the direction of weaker bonding in the crystal structure. Layered Sr3B14O24 (2D) and framework CaB4O7 (3D) built up from various B-O groups expand less anisotropically. Thermal properties of the studied compounds compared to the other alka-line-earth borates are summarized depending on the selected structural characteristics like anion dimensionality, residual charge per one polyhedron (BO3 BO4), cationic size, and structural com-plexity. For the first time these dependencies were established as an average for both types of polyhedra (triangle and tetrahedron) occurring in the same structure at the same time. The most common trends were identified for : (i) Melting temperature decreases as the dimensionality of the borate polyanion, and more precisely, as the residual charge per one polyhedron (triangle or tetrahedron) decreases; (ii) volumetric expansion decreases while the degree of anisotropy in-creases weakly when the residual charge decreases; (iii)both trends (i) and (ii) are most steady within borates built by the triangles only, while the borates built by both triangles and tetrahedra show a larger scatter in values.

In the present study, the problem of the sulfuric acid recycling from spent copper plating solution was solved using a hybrid membrane technology, including diffusion dialysis and electrodialysis. A real solution from the production of copper-coated steel wire, containing 1.45 mol/L of sulfuric acid, 0.67 mol/L of ferrous sulfate and 0.176 mol/L of copper sulfate was processed. Diffusion dialysis with anion-exchange membranes was used to separate sulfuric acid and salts of heavy metals. Then purified dilute sulfuric acid was concentrated by electrodialysis. Energy consumption for sulfuric acid electrodialysis concentration at a current density of 400 A/m2 was 162 W·h/mol with current efficiency 16 %. After processing according to the hybrid membrane scheme, the solution contained 1.13 mol/L sulfuric acid, 0.077 mol/L ferrous sulfate and 0.022 mol/L copper sulfate. The resulting acid solution with a small amount of ferrous sulfate and copper sulfate met the established requirements for a copper plating bath solution and can be reused in production.

Cancer is a complex systemic disease that changes the entire proteome. The analysis of this transformation makes it possible to determine tumor markers, that is, the most characteristic biomacromolecules produced by tumor cells. Here, the question of finding ideal tumor markers, which should be sensitive, specific, and reliable, is an acute issue. Unfortunately, none of the tumor markers, even those used in the clinic, has all these characteristics. Despite this, many tumor markers have demonstrated excellent clinical relevance for monitoring the effectiveness of different treatments for cancer patients. The use of markers also aids in the early detection of cancer recurrence and prognosis. Therefore, the situation in this area can be improved in two ways – by attempting to find an ideal single tumor marker or generating panels of different markers. In both cases, proteomics certainly plays a major role. Human plasma is one of the most popular samples as it is commonly collected in the clinic and provides noninvasive, rapid analysis for any type of disease including cancer. Many efforts have been applied in searching for “ideal” tumor markers digging very deep plasma proteome. There is a line of evidence that the most abundant, so-called “classical plasma proteins”, may be used to generate a tumor biomarker profile. To be comprehensive these profiles should have information not only about protein levels but proteoform distribution for each protein. Initially, the profile of these proteins in norm should be generated. Here, we present data about these profiles generated by two-dimensional electrophoresis with the following mass-spectrometry and immunodetection.

The global climate change mitigation efforts have increased the efforts of national government to incentivize local households in adopting individual renewable energy as a mean to help reduce the usage of electricity generated using fossil fuels and to gain independence from the grid. Since the majority of residential generation is made by PV panels that generate electricity at off-peak hours, the optimal management of such installations often considers local storage that can defer the use of locally generated electricity at later times. On the other hand, the presence of distributed generation can affect negatively the operating conditions of low-voltage distribution networks. The energy stored in batteries located in optimal places in the network can be used by the utility to improve the operation of the network. This paper proposes a metaheuristic approach based on a Genetic Algorithm that considers three different scenarios of using energy storage for reducing the losses in the network. Prosumer and network operator priorities can be considered in different scenarios inside the same algorithm, to provide a comparative study of different priorities in storage placement. A case study performed on a real distribution network provides insightful results.

Data can be illustrated in shapes, and the shapes could provide insight for data modeling and information extraction. Topological data analysis provides an alternative insight in biomedical data analysis and knowledge discovery with the algebra topology tools. In present work, we study the application of topological data analysis for personalized electrocardiographic signal classification toward arrhythmia analysis. Using phase space reconstruction technique, the signal samples are converted into point clouds for topological analysis facility. With topological techniques the persistence landscapes from the point clouds are extracted as features to perform the arrhythmia classification task. We find that the proposed method is robust to the training set size, with only a training set size of 20% percents, the normal heartbeat class are 100% recognized, ventricular beats for 97.13%, supra-ventricular beats for 94.27% and fusion beats for 94.27% within the corresponding experiments. The property of keeping high performance when using smaller training sample proves that the proposed method is especially applicable to personalized analysis. With the present study, we show that the topological data analysis technique could be a useful tool in biomedical signal analysis, and provide powerful ability in personalized analysis.

This paper presents computer and color vision research focusing on human color perception in VR environments. A VR art gallery with digital twins of original artworks is created for this experiment. In this research, the field of colorimetry and the application of CMYK and RGB color models are applied. The interrelationships of the two colors models are applied to create a color modification of the VR art gallery environment using C# Script procedures. This color-edited VR environment works with a smooth change of color tone in a given time interval. At the same time, a sudden change in the color of the RGB environment is defined in this interval. This experiment aims to record a user's reaction embedded in a VR environment and the effect of color changes on human perception in a VR environment. The research uses lie detector sensors that record the physiological changes of the user embedded in VR. Five sensors are used to record the signal. An experiment on the influence of the user's color perception in a VR environment using lie detector sensors has never been conducted. This research defines the basic methodology for analyzing and evaluating the recorded signals from the lie detector. The presented text thus provides a basis for further research in the field of colors and human color vision in a VR environment and lays an objective basis for use in many scientific and commercial areas.

The increasing attendance of paediatric emergency departments becomes a serious health issue. To reduce an elevated burden of medical errors, inevitably caused by high level of stress exerted on emergency physicians, we propose potential areas for improvement in regular paediatric emergency departments. In effort to guarantee demanded quality of care to all incoming patients, the workflow in paediatric emergency departments should be sufficiently optimized. The key component remains implementing one of the validated paediatric triage systems upon patient's arrival at emergency department and fast-tracking patients with low level of risk according to the triage system. To ensure the patient's safety, emergency physicians should follow issued guidelines. Cognitive aids, such as well-designed checklists, posters or flow charts, generally improve physicians' adherence to guidelines and should be therefore available in every paediatric emergency department. To sharpen diagnostic accuracy, the use of ultrasound in paediatric emergency department, according to ultrasound protocols, should be targeted to answer specific clinical questions. Combining all mentioned improvements might reduce number of errors linked with overcrowding. The review serves not only as a blueprint for modernizing paediatric emergency departments, but also as a bin of useful literature which can be suitable in the paediatric emergency field.

The combined muscle-skeletal traumas (MST) are very frequent over the last few years. The emergency care try to save the life of the patient and to receive resuscitation treatment. The role of Trauma surgeon is to choose the right moment for surgery. Aim: To present the management of patient with combined height injury, fracture stabilization, partial foot amputation, local flaps, skin grafting and HIFU – thermotherapy as scar treatment. Materials and methods: 40 years old mail patient, injured after a fall from 8 meters in an elevator shaft. After resuscitation treatment to control the shock the Imaging results are: burst fracture of L3 with spinal canal stenosis, fracture of the sacral bone Denis I, fracture of the right humerus in the proximal third, Monteggia fracture of the left arm, fracture of the proximal third of the right tibia as well as comminuted fractures of both calves and of both heel bones. Results: After a few operations his final result was well healed bone fractures and a good quality soft tissue coverage allowing the patient a satisfactory quality of life. Conclusions: Combined traumas of the muscle- skeletal system are severe, serious and difficult to manage. The good outcome in their treatment requires a team approach between the different medical specialists.

The paradigm of drug delivery via nano- and microcarriers is one of the leading ideas that enable overcoming the limitations of traditional chemotherapy. The trend toward more complex drug carriers capable of multifunctionality is observed in the literature. To date, prospects of stimuli-responsive systems to control the cargo release in the lesion nidus are widely accepted. Both endogenous and exogenous stimuli are employed for this purpose, however, endogenous pH is one of the most common triggers. Unfortunately, scientists face difficulties in the implementation of this idea since a range of biological barriers, drug bioavailability issues, and challenges in the synthesis of carriers with required properties have arisen. Here, we discuss fundamental strategies of pH-responsive drug delivery as well as limits in its application and reveal the main problems, weak sides, and reasons for poor clinical results. Also, we have made an attempt to formulate the profiles of "ideal" drug carrier in the frame of different strategies and considered recently published studies through the lens of these profiles. This approach enables the identification of current trends and promising vectors in the development of pH-responsive drug delivery systems, as well as challenges to be resolved in the next generation of carriers.

The silver fir (Abies alba Mill.) is among the most valuable conifers in Europe for ecological and economic reasons. In the course of history, primarily in the 20th century, its share in stands has been declining due to ill-suited management practices, especially clear-cut management, air pollution, and wildlife-induced damage. Based on recent knowledge of fir ecology and population dynamics, small-scale shelterwood and selection management have been introduced in fir stands, which have also stabilized them. Fir is an essential species for maintaining high stability and biodiversity, especially on planosols and in waterlogged habitats. Due to its shade tolerance and environmental flexibility, particularly at higher altitudes, it can coexist very well with many tree species in mixtures, which can increase the productive potential of stands. It can form stands of heterogeneous structure, ranging from single to multi-layer to selection. For its successful natural regeneration, it is essential to reduce cloven-hoofed game and thus prevent bud browsing damage. On the other hand, fir is a species relatively resistant to bark stripping and the spread of secondary rot compared to Norway spruce (Picea abies [L.] Karst.). During global climate change, fir is expected to shift to higher elevations with sufficient precipitation, while in the southern part of its natural range or at lower elevations, outside water-influenced habitats, it is likely to decline. This paper essentially reviews the description and distribution of the species, its ecological requirements, threats and diseases, habitat and stand conditions, and close-to-nature forest management practices with emphasis on ongoing climate change.

Innovative practices in irrigation systems can bring improvements in terms of economic efficiency and in the same time can reduce environmental impact. Investment in high tech technologies frequently involves additional costs, but an efficient water management can increase the lifetime of the equipment. The main objective of this article is to reduce the energy consumption by one thousand cubic meters pumped and automatically to increase the economic efficiency of the pumping groups. This paper develops a new operating algorithm that ensures the operation of the pumping group at safe operating intervals and in the same time identifies the equivalent pump operating points for the entire flow range and pumping height of the pumping group. This methodology is based on the principles of an Expert System to perform the optimization process of the energy consumption in pumping groups. The resulting methodology avoids the combinatorial explosion of the solutions to be analyzed and determines the point of maximum efficiency without violation of any of the system constraints under any operating condition. The proposed methodology is tested on an irrigation system that includes a pumping group with 5 pumps, showing its effectiveness in obtaining the optimal solution with a relatively low computational burden.

Objectives: Non-adhesive gel-like embolic materials (NAGLEMs) are becoming increasingly dominant in the endovascular treatment of hypervascularised formations in the head and neck due to a combination of their key properties. The main advantages include their lack of adhesion, effective distribution and penetration through pathological vessels, and crucially, their controlla-bility during the process. Our assigned duty was to scrutinise the literature and assess the efficacy and outcomes of administering NAGLEMs, in comparison to other embolizing substances (name-ly, coils, glue, and particles), among patients treated at our clinic. The procedures involved ana-lyzing the technical aspects, efficiency, and safety of endovascular therapy applied to two catego-ries of hypervascular pathological anomalies, surgically managed from 2015 to 2023. Arteriove-nous malformations (AVMs) located in the head, neck, and paragangliomas with jugular/carotid body localization are combined by intense shunting blood flow and shared requirements for em-bolizates used in endovascular treatment (such as penetration, distribution, delayed polymeriza-tion and controllability). An analysis of the literature was also conducted. Results showed 18 pa-tients diagnosed with neck paragangliomas of the carotid body and jugular type. Five patients with arteriovenous malformation (AVM) of the face and neck were included, consisting of 16 fe-males and 7 males with an average age of 55 ± 13 years. Endovascular procedures were conduct-ed using NAGLEMs (ONYX (Medtronic), SQUID (Balt), and PHIL (Microvention)) and dimethyl sulfoxide (DMSO)-compatible balloon catheters. All patients achieved complete or partial embo-lization of hypervascularized formations using one or more stages of endovascular treatment. Additionally, three AVMs of the face and two paragangliomas of the neck were surgically ex-cised following embolization. In other instances, formations were not deemed necessary to be re-moved. The patients' condition upon discharge was assessed by the modified Rankin Scale (mRs) and rated between 0 and 2. Conclusion: Currently, NAGLEMs are predominantly used to treat hypervascularized formations in the neck and head due to their fundamental properties. These properties include a lack of adhesion and a delay in predictable polymerization (after 30-40 minutes). NAGLEMs also exhibit excellent distribution and penetration throughout the vascular bed of the formation. Adequate controllability of the process is largely achieved through the pres-ence of embolism forms of different viscosity, as well as excellent X-ray visualization.

Amine containing polymers are extensively studied as special carriers for short-chain RNA (13–25 nucleotides) which are applied as gene silencing agent in gene therapy of various diseases including cancer. Elaboration of the oligonucleotide carriers requires knowledge about peculiarities of oligonucleotide - polymeric amine interaction. Critical length of the interacting chains is the important parameter which allows to design sophisticated constructions containing oligonucleotide binding segments, solubilizing, protective and aiming parts. We studied interaction of (TCAG)n, n=1-6 DNA oligonucleotides with polyethylenimine and poly(N-(3-((3-(dimethyl­amino)propyl)(methyl)amino)propyl)-N-methylacrylamide). Critical length for oligonucleotides in interaction with polymeric amines is 8-12 units and complexation at these length can be accompanied by "all-or-nothing" effects. New dimethylacrylamide based polymers with grafted polyamine chains were obtained and studied in complexation with DNA and RNA oligonucleotides. The most effective interaction and transfection activity into A549 cancer cells was found for a sample with average number of nitrogens in polyamine chain equal to 27, i.e. for a sample in which all grafted chains are longer the critical length for polymeric amine - oligonucleotide complexation.

Mining activities often generate important amounts of extractive waste, and as a consequence, environmental impacts that affects all factors to a greater or lesser extent. Depending on a variety of variables, the impact can be permanent or temporary, reversible or irreversible, negative or positive. This study conducted research on the status of closure and remediation processes of mining areas in Romania, specifically in the counties of Maramureș, Suceava, Harghita, Alba, Hunedoara, and Caraș-Severin. Furthermore, based on the type and level of pollution, the degree of application of remediation techniques for water and soil pollution in the investigated mining areas was studied. From the analysed information, it is evident that although the closure and remediation process started in Romania over 20 years ago, unfortunately, to this day, the technical projects, technical assistance, and execution of closure and remediation works have not yet completely solved the complex environmental issues in the mining sector. Most of the tailing ponds and waste piles of former mines continue to pose permanent specific risk to the environment and the population. This study concludes that the mining sector in Romania, although it has the necessary techniques and technologies for the ecological rehabilitation of degraded lands related to the Extractive Waste Facilities and the elimination of negative impacts on the environment and public health, has not yet been able to fully concretize its remediation efforts.

Depressive disorder (DD) is a psychiatric disorder whose molecular basis is not fully understood. It is assumed that reduced consumption of fish and omega-3 fatty acids (FA) is associated with DD. Other lipids like total cholesterol (TCH), LDL- and HDL-cholesterols (LDL-CH, HDL-CH) also play a role in depression. This study aimed to investigate the relationship between depressive disorder symptoms and lipid profile, LDL- and HDL-cholesterol subfractions, Paraoxonase 1 (PON1) activities and erythrocyte membrane fluidity in 58 depressive children and adolescents, as well as the effect of omega-3 FA on the monitored parameters. Depressive symptoms were assessed by the Children's Depression Inventory (CDI), lipid profile by standard biochemical procedures, LDL- and HDL-subfractions by the Lipoprint system. Basic biochemical parameters including lipid profile were compared with levels in 20 healthy children and were in the physiological range. We are the first to report that omega-3 FAs increase after 12 weeks of supplementation large HDL subfractions (anti-atherogenic) and decrease small HDL subfractions (pro-atherogenic) in depressed children. We found a negative correlation between CDI score and HDL-CH and large HDL subfraction, but not LDL-CH subfractions. CDI score was not associated with erythrocyte membrane fluidity. Our results suggest that HDL-CH and its subfractions, but not LDL-CH may play a role in the pathophysiology of depressive disorder.

This paper uses preliminary studies of archaeological sites (burial mounds and settlements) from the Iron Age through Medieval periods (ca. 800 BCE to 1200 CE) in the Juuku Valley on the South side of Lake Issyk-Kul to model land-use across vertical mountain zones. To do so, we have established a radiometric chronology, conducted test excavations of an Iron Age settlement and a Turkic period burial, undertaken preliminary archaeobotanical research, and pedestrian surveys. Seed remains of wheat (Triticum aestivum), barley (Hordeum vulgare), broomcorn millet (Panicum milaceum) and foxtail millet (Setaria italica) and legumes were recovered in very small quantities from an Iron Age upland settlement at 2100 m asl and a Turkic period burial mound at 1934 m asl. These preliminary archaeobotanical results are compared to the Talgar Iron Age settlements on the north side of the Tian Shan Mountain range in Kazakhstan studied earlier by Robert Spengler. Small samples of faunal remains found at the Turkic period kurgan and from a profile at the upland Iron Age settlement indicate livestock herding of sheep/goats, cattle, and horses in Juuku Valley. The goal of this paper is to test the hypothesis that pastoral transhumance and agropastoralism were economic strategies used by ancient societies during the Iron Age through Medieval periods in mountain-river valley areas between 750 m to 2500 m asl. These economic strategies that combined the pasturing of sheep, goats, cattle and horses with the cultivation of cereals were adapted to the use of different vegetational zones along a vertical gradient. This paper based on preliminary research of upland sites of the Juuku Valley in Kyrgyzstan, initiates a long-term research study of four millennia of settlements that ranged from pastoral transhumance, pastoral nomadism, and combined mountain agriculture using survey data and test excavations.

The Malyy (Little) Murun massif of the Aldan Shield of the Siberian Craton has long been a kind of the geologists’ Siberian Mecca. It attracted thousands of geologists, prospectors and mineral collectors despite of its remote location. It is famous for a dozen of new and rare minerals, including gemstones charoite and dianite (the latter is the market name for strontian potassicrichrerite), as well as for specific alkaline igneous rocks. Despite of this, the age of the Malyy Murun igneous complex and associated metasomatic and hydrothermal mineral associations remained poorly constrained. In this paper, we provide extensive 40Ar/39Ar geochronological data to reveal its age and temporal history. It appeared that being unique in terms of rocks and constituent minerals, the Malyy Murun is one of multiple alkaline massifs and lavas emplaced in Early Cretaceous (~137-128 Ma) within a framework of extensional setting of the Aldan Shield and nearby Transbaikalian region. The extension has occurred 40-60 million years after the supposed closure of the Mongolia-Okhotsk Ocean and peak of orogeny in Early-Middle Jurassic.

Droplet-based microfluidics has revolutionized numerous fields such as biomedical research, pharmaceuticals, drug discovery, food engineering, flow chemistry, and cosmetics. This paper presents a comprehensive study focusing on the detection and characterization of droplets with volumes in the nanoliter range. Leveraging the precise control of minute liquid volumes, we introduced a novel spectroscopic On-Chip microsensor equipped with integrated microfluidic channels for droplet generation, characterization, and sensing, simultaneously. The microsensor, designed with Interdigitated-Ring-Shaped Electrodes (IRSE) and seamlessly integrated with microfluidic channels, offers enhanced capacitance and impedance signal amplitudes, reproducibility, and reliability in droplet analysis. We were able to make analyses of droplets length in the range 1.0-6.0 mm, velocity 0.66-2.51 mm/s, droplet volume 1.07nL-113.46nL. Experimental results demonstrated that the microsensor's has a great performance in terms of droplet size, velocity, and length, with a significant signal amplitude of capacitance and impedance, and real-time detection capabilities, thereby highlighting its potential for facilitating microcapsule reactions and enabling on-site real-time detection for chemical and biosensor analyses on-chip.

Arable Сhernozems with high SOC contents have the potential to be significant sources of GHGs, and climate change is likely to increase SOC losses, making the issue of carbon sequestration in this region even more important. The prospect of maintaining SOC stock or increasing it by 4% an-nually under planned management practice modifications for the period up to 2090 was evaluated using a long-term experiment on Haplic Chernozem in the Rostov Region, Russia. In this study, we used the RothC model to evaluate SOC dynamics for three treatments with mineral and organic fertilization under two adaptation scenarios vs. business as usual, as well as under two climate change scenarios. Correction of crop rotation and the application of organic fertilizers at high rates are essential tools for maintaining and increasing SOC stocks. This can maintain SOC stock at the level of 84–87 Mg∙ha-1 until the middle of the 21st century, as the first half of the century is con-sidered the most promising period for the introduction of adaptation measures for the additional accumulation of SOC on Chernozems. Part of the additional accumulated SOC is expected to be lost before 2090.

We have shown that lipid-associated loci discovered by genome-wide association studies (GWAS) have pleiotropic effects on lipid metabolism, carotid intima-media thickness (CIMT), and CAD risk. Here, we investigated the impact of lipid-associated GWAS loci on the efficacy of rosuvastatin therapy in terms of changes in plasma lipid levels and CIMT. The study comprised 116 CAD patients with hypercholesterolemia. CIMT, total cholesterol (TC), low-density lipoprotein cholesterol (LDL-C), and triglycerides (TG) were measured at baseline and after 6 and 12 months of follow-up, respectively. Genotyping of fifteen lipid-associated GWAS loci was performed by the MassArray-4 System. Linear regression analysis adjusted for sex, age, body mass index, and rosuvastatin dose was used to estimate the phenotypic effects of polymorphisms, and P-values were calculated through adaptive permutation tests. Over one-year therapy, a decrease in CIMT was linked to rs1689800, rs4846914, rs12328675, rs55730499, rs9987289, rs11220463, rs16942887, and rs881844 polymorphisms (Pperm&lt;0.05). TC change was associated with rs55730499, rs11220463, and rs6065906; LDL-C change was linked to the rs55730499, rs1689800, and rs16942887 polymorphisms; and TG change was linked to polymorphisms rs838880 and rs1883025 (Pperm&lt;0.05). In conclusion, the polymorphisms rs1689800, rs55730499, rs11220463, and rs16942887 were found to be predictive markers for multiple antiatherogenic effects of rosuvastatin in CAD patients.

The influence of neutrosophy in the previous period is constantly growing in many areas of science and technology. Moreover, various applications of the neutrosophic approach have become more common in recent years. Our goal in this research is to utilize the neutrosophy to improve the performance of the Dai-Liao conjugate gradient (CG) method. Specifically, in this research, we propose and investigate a new neutrosophic logic system to calculate the key parameter t involved in the Dai–Liao CG iterations. Theoretical analysis and numerical experience indicate that the efficiency and robustness of the new rule for determining t. Combining the neutrosophy and the Dai-Liao conjugate gradient method, we propose and explore a new Dai-Liao CG iterations for solving large-scale unconstrained optimization models. The global convergence is established under common assumptions and the backtracking line search. Finally, by conducting numerical experiments, computational evidence demonstrates that the new fuzzy neutrosophic Dai-Liao conjugate gradient method is computationally effective and robust.