Evidence-based canine decontamination protocols are underrepresented in the veterinary literature. Aerosolized microbiological and chemical contaminants can pose a risk in deployment environments highlighting the need for improved canine field decontamination strategies. Prior work has established the efficacy of traditional, water-intensive methods on contaminant removal from the coat of the working canine; however, it is not known if similar reductions can be achieved with simple field expedient methods when resources are limited. The objective of this study was to measure the reduction of aerosolized contamination via a practical “wipe-down” procedure performed on working canine coats contaminated with a fluorescent, non-toxic, water-based aerosol. Disposable, lint-free towels were saturated with one of three treatments: water, 2% chlorhexidine gluconate scrub (CHX), or 7.5% povidone-iodine scrub (PVD). Both CHX and PVD were diluted at a 1:4 ratio. Treatments were randomly assigned to one of three quadrants established across the shoulders and back of commonly utilized working dog breeds (Labrador retrievers, n = 16; German shepherds, n = 16). The fourth quadrant remained unwiped, serving as a control. Reduction in fluorescent marker contamination was measured and compared across all quadrants. PVD demonstrated greater marker reduction compared to CHX or water in both breeds (P < 0.0001). Reduction was similar between CHX or water in Labradors (P = 0.86) and shepherds (P = 0.06). Effective wipe-down strategies using common veterinary cleansers should be further investigated and incorporated into decontamination practices to safeguard working canine health and prevent cross-contamination of human personnel working with these animals.

Residual stress (RS) is the most challenging problem in metal additive manufacturing (AM) since the build-up of high tensile RS may influence the fatigue life, corrosion resistance, crack initiation, and failure of the additively manufactured components. While tensile RS is inherent in all the AM processes, fast and accurate prediction of stress state within the part is extremely valuable and would result in optimization of the process parameters in achieving a desired RS and control of the build process. This paper proposes a physics-based analytical model to rapidly and accurately predict the RS within the additively manufactured part. In this model, a transient moving point heat source (HS) is utilized to determine the temperature field. Due to the high temperature gradient within the proximity of the melt pool area, material experience high thermal stress. Thermal stress is calculated by combining three sources of stresses known as stresses due to the body forces, normal tension, and hydrostatic stress in a homogeneous semi-infinite medium. The thermal stress determines the RS state within the part. Consequently, by taking the thermal stress history as an input, both the in-plane and out of plane RS distributions are found from incremental plasticity and kinematic hardening behavior of the metal by considering volume conservation in plastic deformation in coupling with the equilibrium and compatibility conditions. In this modeling, material properties are temperature-sensitive since the steep temperature gradient varies the properties significantly. Moreover, the energy needed for the solid-state phase transition is reflected by modifying the specific heat employing the latent heat of fusion. Furthermore, the multi-layer and multi-scan aspects of metal AM are considered by including the temperature history from previous layers and scans. Results from the analytical RS model presented excellent agreement with XRD measurements employed to determine the RS in the Ti-6Al-4V specimens.

Selective laser melting (SLM) is one of the widely used techniques in metallic additive manufacturing, in which high-density laser powder is utilized to selectively melting layers of powders to create geometrically complex parts. Temperature distribution and molten pool geometry directly determine the balling effect, and concentrated balling phenomenon significantly deteriorates surface integrity and mechanical properties of the part. Finite element models have been developed to predict temperature distribution and molten pool geometry, but they were computationally expensive. In this paper, the three-dimensional temperature distributions are predicted by analytical models using point moving heat source and semi-ellipsoidal moving source respectively. The molten pool dimensions under various process conditions are obtained from the three-dimensional temperature predictions and experimentally validated. Ti-6Al-4V alloy is chosen for the investigation. Good agreements between the predictions and the measurements are observed. The presented models are also suitable for other metallic materials in the SLM process.

To accurately identify high-quality functional wood with superior mechanical properties and enhance its durability, it is imperative to understand the relationships between the physical and mechanical attributes of diverse wood types. Presently, there exist issues related to accuracy, efficiency, and differentiation in studying these performance correlations. The Liang Kleeman (L-K) information flow theory, a causative analytical approach rooted in fundamental physics principles, offers swift computational capabilities. Furthermore, the coefficient of variation in L-K information flow quantitatively gauges the intensity of causal effects. Therefore, this article adopts a causal artificial intelligence perspective and introduces a wood performance analysis method based on L-K information flow.This study focuses on four Chinese fir varieties, including fast-growing Chinese fir (YKS), red heart Chinese fir (CSH, XXH), and iron heart Chinese fir (XXT). By computing and comparing variation coefficients of L-K information flow for various physical properties and their impact on mechanical properties, causal relationships between these properties are elucidated. These findings are then applied to predict wood mechanical properties, achieving a remarkable maximum accuracy of 90%.In the future, these findings will prove invaluable for the selection of high-quality wood and for improving the manufacturing process to prolong the service life of functionalized wood.

Different process parameters can alter the temperature during machining. Consequently, selecting process parameters that lead to a desirable cutting temperature would help to increase the tool life, decrease the tensile residual stress, and controls the microstructure evolution of the workpiece. An inverse computational methodology is proposed to design the process parameters for specific cutting temperature. A physics-based analytical model is used to predict the temperature induced by cutting forces. To calculate the temperature induced by the deformation in the shear zone, a moving point heat source approach is used. The shear deformation and chip formation model is implemented to calculate machining forces as functions of process parameters, material properties, and etc. The proposed model uses the analytical model to predict the cutting temperatures and applies a variance-based recursive method to guide the inverse analysis. In order to achieve the cutting process parameters, an iterative gradient search is used to adaptively approach the specific temperature by the optimization of process parameters such that an inverse reasoning can be achieved. Experimental data are used to illustrate the implementation and validate the viability of the computational methodology.

Cultural tourism in Tanzania presents a diverse tapestry of traditions, varied ethnic groups, and historical accounts. This article aims to pinpoint areas for further exploration in the cultural tourism sector of Tanzania and analyze their potential impacts. The study conducted a systematic review of the literature following established inclusion criteria as well as the Preferred Reporting Items for Systematic Reviews and meta-analysis guidelines. A total of 21 articles focused on Tanzania Cultural Heritage Tourism from sources such as Google Scholar and web databases were examined, revealing several research gaps, including theoretical, contextual and methodological aspects. Furthermore, the research offers insights into theoretical implications and recommends avenues for future studies that could advance the field by addressing these knowledge gaps providing valuable direction to new researchers interested in exploring these specific areas as well as practitioners seeking a comprehensive understanding of various aspects related to Tanzania's cultural heritage tourism

The aim of this work is to compare two softwares (MAUD and TOPAS) based on the Rietveld algorithm and to test the concept of tolerance factor using the dissolution at high temperature of yttrium into BaTiO₃. In general, both softwares give up different values of the crystalline parameters however the trends are similar in most cases but the analysis of the strain and crystallite size in the BaTiO₃ crystals suggests that, in this particular case, MAUD offered results more consistent with the expected behavior. Using the crystalline parameters calculated by Rietveld, the tolerance factor values were obtained and these data suggest even better stability in the crystalline structure than that expected using theoretical parameters. Tolerance factor concept also indicates that Ti⁴⁺ should be preferred.

Temperature field is an essential attribute of metal additive manufacturing in view of its bearings on the prediction, control, and optimization of residual stress, part distortion, fatigue, balling effect, etc. This work provides an analytical physics-based approach to investigate the effect of scan strategy parameters including time delay between two irradiations and hatching space on thermal material properties and melt pool geometry. This approach is performed through the analysis of the distribution of material properties and temperature profile in three-dimensional space. The moving point heat source approach is used to predict the temperature field. To predict the temperature field during the additive manufacturing process some important phenomena are considered. 1) Due to the high magnitude of temperature in the presence of the laser, the temperature gradient is usually high which has a crucial influence on thermal material properties. Consequently, the thermal material properties of stainless steel grade 316L are considered to be temperature-dependent. 2) Due to the repeated heating and cooling, part usually undergoes several melting and solidification cycles. This physical phenomenon is considered by modifying the heat capacity using the latent heat of melting. 3) The multi-layer aspect of metal AM process is considered by incorporating the temperature history from the previous layer since the interaction of the successive layers has an impact on heat transfer mechanisms. 4) Effect of heat affected zone on thermal material properties is considered by the superposition of material properties in regions where the temperature fields of two consecutive irradiations have an overlap since the consecutive irradiations change the behavior of the material properties. The goals are to 1) investigate the effects of temperature-sensitive material properties and constant material properties on the temperature field. 2) Study the behavior of thermal material properties under different scan strategies. 3) Study the importance of considering the effect of heat affected zone on thermal material through the prediction of melt pool geometry. 4) Investigate the effect of hatching space on melt pool geometry. This work is purely employed physics-based analytical models to predict the behavior of material properties and temperature field under different process conditions, and no finite element modeling is used.

Residual stress (RS) is the most challenging problem in metal additive manufacturing (AM) since the build-up of high tensile RS may influence the fatigue life, corrosion resistance, crack initiation, and failure of the additively manufactured components. While tensile RS is inherent in all the AM processes, fast and accurate prediction of stress state within the part is extremely valuable and would result in optimization of the process parameters in achieving a desired RS and control of the build process. This paper proposes a physics-based analytical model to rapidly and accurately predict the RS within the additively manufactured part. In this model, a transient moving point heat source (HS) is utilized to determine the temperature field. Due to the high temperature gradient within the proximity of the melt pool area, material experience high thermal stress. Thermal stress is calculated by combining three sources of stresses known as stresses due to the body forces, normal tension, and hydrostatic stress in a homogeneous semi-infinite medium. The thermal stress determines the RS state within the part. Consequently, by taking the thermal stress history as an input, both the in-plane and out of plane RS distributions are found from incremental plasticity and kinematic hardening behavior of the metal by considering volume conservation in plastic deformation in coupling with the equilibrium and compatibility conditions. In this modeling, material properties are temperature-sensitive since the steep temperature gradient varies the properties significantly. Moreover, the energy needed for the solid-state phase transition is reflected by modifying the specific heat employing the latent heat of fusion. Furthermore, the multi-layer and multi-scan aspects of metal AM are considered by including the temperature history from previous layers and scans. Results from the analytical RS model presented excellent agreement with XRD measurements employed to determine the RS in the Ti-6Al-4V specimens.

This paper addresses the analysis for the nonlinear vibration response of a rectangular tube with a flexible end and non-rigid acoustic boundaries. This is a further work of the linear structural acoustic problem in a well-known acoustic book. In fact, the acoustic boundaries of an enclosed space sometimes are non-rigid and the structural vibration responses are nonlinear. These two points are the focuses of this paper. The multi-level residue harmonic balance method is applied to this nonlinear structural acoustic problem. The results obtained from the multi-level residue harmonic balance method and numerical method are generally in good agreement. The effects of excitation magnitude, tube length, and phase shift parameter etc. are examined.

The high genetic diversity of the tomato and its high micronutrient content make this fruit very interesting from an economic and nutritional point of view. The genetic erosion suffered by this crop, due to breeding objectives based on yield and marketing, makes it necessary to return to the origins in search of the nutritional and organoleptic quality lost in traditional varieties. In this study, the agronomic, physical, organoleptic and nutritional characteristics of eighteen F1 hybrids obtained by crossing fourteen traditional varieties, previously selected for their quality, were studied to select genotypes of superior quality that could be candidates for new. All parameters studied were strongly influenced by genotype, showing a wide range between cultivars. Principal Component Analysis revealed the characteristics of each hybrid that made it stand out from the others. Some hybrids (H3, H4, and H6) stand out because of their high concentration of active compounds, others (H16, H15, H10, H17, H9, and H11) because of agronomic performance and high content of β-carotene, and H5 was the only one to contain chlorophyll in their ripe fruits. Finally, the evaluation index allowed the selection of five hybrids with interesting characteristics, combining good yield performance and high quality

Selective laser melting is an emerging Additive Manufacturing (AM) technology for metals. Intricate three-dimensional parts can be generated from the powder bed by selectively melting the desired location of the powders. The process is repeated for each layer until the part is built. The necessary heat is provided by a laser. Temperature magnitude and history during SLM directly determine the molten pool dimensions, thermal stress, residual stress, balling effect, and dimensional accuracy. Laser-matter interaction is a crucial physical phenomenon in the SLM process. In this paper, five different heat source models are introduced to predict the three-dimensional temperature field analytically. These models are known as steady state moving point heat source, transient moving point heat source, semi-elliptical moving heat source, double elliptical moving heat source, and uniform moving heat source. The analytical temperature model for all of the heat source models are solved using three-dimensional differential equation of heat conduction with different approaches. The Steady state and transient moving heat source are solved using separation of variables approach. However, the rest of models are solved by employing the Green’s functions. Due to the high magnitude of the temperature in the presence of the laser, the temperature gradient is usually high which has a substantial impact on thermal material properties. Consequently, the temperature field is predicted by considering the temperature sensitivity thermal material properties. Moreover, due to the repeated heating and cooling, the part usually undergoes several melting and solidification cycles, this physical phenomenon is considered by modifying the heat capacity using latent heat of melting. Furthermore, the multi-layer aspect of metal AM process is considered by incorporating the temperature history from the previous layer since the interaction of the layers have an impact on heat transfer mechanisms. The proposed temperature field models based on different heat source approaches are validated using experimental measurement of melt pool geometry from independent experimentations. The detailed explanation of the comparison of models is also provided. Moreover, the effect of process parameters on the balling effect is also discussed.

In this study, I will present some documentary evidence that Carlos Drummond de Andrade’s poem “A Máquina do Mundo” [The Machine of the World] (1949) was based on prior reflections contained in a forgotten newspaper article entitled “Poesia e Pesadelo” [Poetry and Nightmare] (1949). In that article, Drummond critically analyzed some of the theses of Stephen Spender's essay “What Is Modern in Modern Poetry” (1948), which had just been published in The Tiger's Eye magazine. As soon as he read Spender's text, Drummond wrote “Poetry and Nightmare” and began to elaborate a narrative poem whose protagonist would be a machine. All the documentary evidence indicates that Drummond took Spender's lessons as touchstones for the elaboration of the narrative and allegorical structure of “The Machine of the World.” According to the interpretation I am proposing here, Drummond, in writing the machine poem, put into practice at least six lessons drawn from Spender’s essay, namely: 1) the modern poet must represent the tension between the external machinelike landscape and the landscape of the inner world of the creative imagination; 2) he must also represent the machinelike, ugly, and urban world around him in a beautiful and poetic way; 3) he must avoid the misconceptions of excessive utopian visionarism, as well as creeping realism; 4) he must reject the imperative of political engagement, whose principle of action states that poetry has a transformative mission in society; 5) he must free himself from the obsession with free verse as the only form of modern poetry and start using the traditional fixed forms; 6) he must understand machines as poetic symbols of human passions, and not just as exotic objects foreign to human reality. My conclusion is that, after reading Spender’s essay, Drummond changed his aesthetic and philosophical understanding of what defines the essence of modern poetry, both in terms of form and content.

Cutaneous mycoses are common infections whose treatment has become more complex due to increasing antifungal resistance and the need for prolonged therapies, hindering patient adher-ence and increasing the incidence of adverse effects. Consequently, the use of physical therapies, especially photodynamic therapy (PDT), has increased for the treatment of onychomycosis due to its antimicrobial capacity mediated by the production of reactive oxygen species. This study investigates the in vitro effect of the combination of blue light (448 nm) and red light (645 nm) with terbinafine on the cell viability of human keratinocytes and the production of reactive ox-ygen species. The combination of terbinafine and blue light exhibits a synergistic effect on the production of reactive oxygen species and a significant increase in the expression of superoxide dismutase (SOD), an enzyme involved in the reduction of superoxide ions (O2-) and the genera-tion of hydrogen peroxide (H2O2). Such effect could be useful in clinical practice to improve the response of cutaneous mycoses to pharmacological treatment, reduce their toxicity, and shorten their duration.

Social robots may become an innovative means to improve the well-being of individuals. Earlier research showed that people easily self-disclose to a social robot even in cases where that was unintended by the designers. We report on an experiment of self-disclosing in a diary journal or to a social robot after negative mood induction. The off-the-shelf robot was complemented with our inhouse developed AI chatbot and could talk about ‘hot topics’ after having it trained with thousands of entries on a complaint website. We found that people who felt strong negativity after being exposed to shocking video footage benefited the most from talking to our robot rather than writing down their feelings. For people less affected by the treatment, a confidential robot chat or writing a journal page did not differ significantly. We discuss emotion theory in relation to robotics and possibilities for an application in design (the emoji-enriched ‘talking stress ball’). We also underline the importance of - otherwise disregarded - outliers in a data set that is of a therapeutic nature.

In polymer-based dental composites, wear is a three-body wear system mainly abrasive, because of the food particles and wear products suspended in the oral cavity, which are transferred to the microcavities of the surface of the replacements. Due to this fact, the incorporation of nanodiamond as reinforcement in these polymer matrix composites, which promotes the creation of a solid lubricant tribofilm surface could be advantageous. When nanodiamond is added in contents of 0.8, 1.6 and 3.2 wt %, an increase in microhardness from 95 up to 420 %, compared to the one of neat BisGMA/TEGDMA, is observed. Additionally, the incorporation of a content of 1.6 wt % is enough to cause a diminution of ~78 % in the friction coefficient and a reduction of the specific wear rate and Archard’s coefficient of ~50 %. Nevertheless, the addition of relatively high contents reduces the effectiveness of photoinitiation and UV-curing, which is related to the scattering and absorption of UV radiation by ND.

The Rev. Martin Luther King Jr. and Nelson Mandela were two of the world's most iconic civil (political) (human) rights advocates and leaders of all time. Both advocated for, and to varying degrees, applied elements of peaceful protests to the achievement of their goals. Both spent time in jail, often concurrently, but eventually forced their respective countries to extend the same rights that white populations had denied Africans and African Americans. For the US, civil rights, voting rights, right to education, housing and housing loans suggested that equality had been achieved, capped in South Africa by the election of Nelson Mandela as the first majority-rule president, and in the US, by Barack Obama’s election to the presidency. Yet the historical over-policing, police mistreatment and more generally, the judicial system’s inordinate ‘targeting’ of African Americans, with egregious cases running from Emmett Till to Rodney King to Walter Scott to Breonna Taylor to George Floyd to Rayshard Brooks and thousands of others shows the danger of such magical thinking. The now-persistent global wave pursuing human rights, civil rights and the right to be treated equally, primarily driven by the loosely-organized Black Lives Matter (BLM) movement, has become the leading voice in pursuit of equality. Riots such as those in LA, protests in Ferguson and everywhere in summer 2020 has ushered new civil rights campaign. In the US and elsewhere, it has morphed to include historical issues such as monuments to colonialism, the US civil war, slavery and slave owners and traders, institutions, companies and people whose wealth and existence has links to slavery. Instructively, the protests persisted even as COVID-19, the hundred-year plague, continues to ravage the world. Lost in the moment is the absence of central leadership and leaders such as MLK or Mandela. Their charisma and effectiveness has been lacking for 50 years. This paper evaluates whether this has led to inconsistent civil and human rights pursuit for equality, or whether perchance, Mandela and MLK were extraordinary, once-in-a-lifetime transformative leaders uniquely selected by history for their time.

1. Background: The global COVID-19 lockdowns are unique psychological factors, requiring adjustment and coping. This illustrative, South African case study investigated the influence the COVID-19 lockdown context would have on meditation and physical activity. As these were lifestyle patterns the null hypothesis was of no change. 2. Method: The methodology consisted of quantitative and qualitative phases. The quantitative phase was an empirical, case study review of data from the author’s HeartMath and Fitbit electronic devices, as from 9 November 2019 to 31 July 2021. This consisted of coherence and achievement data from the HeartMath Inner Balance application (app), as well as distance and activity data from the Fitbit app. The qualitative phase consisted of the selection and illustration of meditation sessions documented over lockdown. 3. Results: The highly significant increases in physical activity and meditation coherence and achievement collectively indicated significant health promotion over the COVID-19 Lockdown period. Subtle energetic, experiential descriptions of meditation apprehensions resonated and supported these quantitative findings. 4. Conclusions: COVID-19 lockdown has meant transformation, humility, and reordering of priorities. The meditation descriptions amplified information from the HeartMath and Fitbit electronic devices, together co-creating conscious, embodied, relationship science for discussion, instruction, and further research.

In the process of metal cutting, the anti-wear performance of the tool determines the life of the tool and affects the surface quality of the workpiece. The finite element simulation method can directly show the tool wear state and morphology, but due to the limitations of the simulation time and complex boundary conditions, it has not been commonly used in tool life prediction. Based on this, a tool wear model was established on the platform of a finite element simulation software for the cutting process of titanium alloy TC4 by end milling. The key technique is to embed different types of tool wear models into the finite element model in combination with the consequent development technology. The effectiveness of the tool wear model is validated by comparing the experimental results with the simulation results. At the same time, in order to quickly predict the tool life, an empirical prediction formula of tool wear was established, and the change course of tool wear under time change was obtained.

Our objective was to investigate the effects of topically applied neuropeptide Y (NPY) on ischemic wounds. Initially, the animal model for ischemic wound healing was validated using 16 male Sprague-Dawley albino rats. In the intervention study, an additional 28 rats were divided into three groups: NPY (0.025%), the positive control insulin-like growth factor-I (IGF-I, 0.0025%), and the hydrogel carrier alone (control). The hydrogel was selected due to its capacity to prolong NPY release (p &lt; 0.001), as demonstrated in a Franz diffusion cell. In the animals, an 8-mm full-thickness wound was made in a pedunculated dorsal ischemic skin flap. Wounds were then treated and assessed for 14 days, and procured at the end of the experiment for in situ hybridization analysis (RNAscope®) targeting NPY receptor Y2R and for meticulous histologic examination. Wound healing rates, i.e. the percentage wound area changes, did not show an increase with NPY (p = 0.938) but did with rhIGF-I (p = 0.039) compared to the control. Y2R mRNA was not detected in the wounds or adjacent skin but was identified in the rat brain (positive control). Light microscopic examination revealed trends of increased angiogenesis and enhanced inflammatory cell infiltration with NPY compared to control. An interesting secondary discovery was the presence of melanophages in the wounds. Our findings suggest the potential of NPY to enhance neovascularization under ischemic wound healing conditions, but further optimization of the carrier and dosage is necessary. The mechanism is elusive but likely involves NPY receptor subtypes other than Y2R.

Based upon a radically new approach, this paper describes a 2-box absolute flow model that calculates the CO₂ transfer between the atmosphere and a terrestrial / ocean mixing reservoir. Given the inputs of anthropogenic fossil fuel emissions (CO2ff), atmospheric CO₂ mixing-ratio and nuclear weapons bomb yields, the model calculates atmospheric d¹³C and Δ¹⁴C time-series, with the level of agreement for d¹³C being to within ± 0.05 ‰, for Δ¹⁴C to within ± 3‰, spanning 200 years. The model contains only seven internal parameters which are varied to optimize the fit. Yet according to conventional wisdom, this model should not work. It is commonly held that the ¹³C and ¹⁴C isotopic forms of carbon bypass seawater carbonate chemistry, resulting in very different absorption properties (Revelle factor) as compared to ¹²C. This study rejects this assumption, and uses the same residence time and reservoir mixing properties for all isotopes. The paper includes an analysis justifying why the isotopic bypass of the Revelle factor is not significant. The study describes the use of the model to track CO2ff takeup using two separate measures, a) the amount of molecular CO2ff remaining in the atmosphere and b) the amount of atmospheric growth attributable to CO2ff, thereby resolving discrepancies in published values.

The increased adoption of information and communication technology for smart grid applications will require innovative cyber-physical system (CPS) testbeds to support research and education in the field. The groundbreaking CPS testbeds with realistic and scalable platforms have progressively gained interest in recent years, with electric power flowing in the physical layer and information flowing in the network layer. However, CPSs are critical infrastructures and not designed for testing or direct training, as any misbehaving in an actual system operation could cause a catastrophic impact on its operation. Based on that, it is not easy to efficiently train professionals in CPSs. Aiming to support the advancement and encourage the training of industry professionals, this paper proposes and develops a complete testbed with commercial tools. The testbed can reliably replicate the performance of smart grid systems and the main potential cyber threats that electric grids may face. The complex interdependencies between the cyber and physical domains are discussed in detail, and different case scenarios are presented, providing insightful guidelines for key features and design decisions for future smart grid testbeds.

Photobiomodulation (PBM) is a procedure that uses light to modulate cellular functions and bio-logical processes. Over the past decades, PBM has gained considerable attention for its potential in various medical applications due to its non-invasive nature and minimal side effects. This narrative review article examines the existing literature on PBM, encompassing research studies, clinical trials, and technological developments. This review highlights the mechanisms of action underlying PBM, including the interaction with cellular chromophores and the activation of in-tracellular signaling pathways. The evidence from clinical trials and experimental studies to evaluate the efficacy of PBM in clinical practice is summarized with a special emphasis on der-matology. Furthermore, advancements in PBM technology, such as novel light sources and treat-ment protocols, are discussed in the context of optimizing therapeutic outcomes and improving patient care. This narrative review underscores the promising role of PBM as a non-invasive therapeutic approach with broad clinical applicability. Despite the need for further research to develop standard protocols, PBM holds great potential for addressing a wide range of medical conditions and enhancing patient outcomes in modern healthcare practice.

Based on the dynamic strength variation mechanism of concrete under complex loading conditions, two approaches were devised: numerical testing and CT scanning, guided by the principle of minimizing energy dissipation. A methodology for calculating concrete's failure area and measuring its strength was developed. The analysis delves into the mechanisms behind failure patterns and variations in concrete specimen strength, focusing on crack initiation, development, and the resultant failure surface formed by crack propagation, along with the stress distribution in concrete specimens subjected to diverse loading conditions. Through evaluating the strength and computed failure area of concrete specimens, it is evident that the loading method influences both the strength and failure area of concrete specimens. In general, a larger failure area correlates with a higher measured strength.

Although total nett CO₂ atmospheric flow can be estimated with reasonable accuracy, the contributing gross fluxes between the atmosphere and the earth's surface are poorly understood. This paper presents a method, driven by the objective of simplicity, by which the global outflow and inflow of CO₂ between atmosphere and a globally equivalent "mixing reservoir" can be estimated, using the isotopes ¹⁴C and ¹³C as tracers. It has been asserted that the isotopic carbon in CO₂ cannot be directly used as a tracer in flow studies because it is not subject to the Revelle factor. Evidence is provided showing that this view is mistaken. The model contains 7 key parameters which are used to create synthetic records of Δ¹⁴C and d¹³C spanning 200 years or more, including during the period of atmospheric weapons testing and its decay known as the "bomb pulse". By optimising the fit between these computed values and the historical records of d¹³C and Δ¹⁴C, all seven key parameters are determined. The effective "mixing reservoir" is thereby determined to have a size around six times that of the atmosphere, with global outflux rising from 39.7 GTC yr-1 in 1750 to 58.9 GTC/yr in 2020, this figure probably not including annually cycled carbon.

Floods and droughts are driven, in part, by spatial patterns of extreme rainfall. Heat waves are driven by spatial patterns of extreme temperature. It is therefore of interest to design statistical methodologies that allow the identification of likely patterns of extreme rain or temperature from observed historical data. The standard work-horse for identifying patterns of climate variability in historical data is Principal Component Analysis (PCA) and its variants. But PCA optimizes for variance not spatial extremes, and so there is no particular reason why the first PCA spatial pattern should identify, or even approximate, the types of patterns that may drive these phenomena, even if the linear assumptions underlying PCA are correct. We present an alternative pattern identification algorithm that makes the same linear assumptions as PCA, but which can be used to explicitly optimize for spatial extremes. We call the method Directional Component Analysis (DCA), since it involves introducing a preferred direction, or metric, such as `sum of all points in the spatial field'. We compare the first PCA and DCA spatial patterns for US rainfall anomalies on a 6 month timescale, using the sum metric for the definition of DCA in order to focus on total rainfall anomaly over the domain, and find that they are somewhat different. The definitions of PCA and DCA result in the first PCA spatial pattern having the larger explained variance of the two patterns, while the first DCA spatial pattern, when scaled appropriately, has a higher likelihood and greater total rainfall anomaly, and indeed is the pattern with the highest total rainfall anomaly for any given likelihood. In combination these two patterns yield more insight into rainfall variability and extremes than either pattern on its own.

This paper presents a new implementation of a 2-box absolute flow model, enabling the calculation of CO₂ transfer between the atmosphere and a mixing reservoir representing the combined effect of the terrestrial and ocean regions. The model uses published values of anthropogenic CO₂ fossil fuel emissions (CO2ff), atmospheric CO₂ mixing ratio and nuclear weapons bomb yields, to compute atmospheric d¹³C and Δ¹⁴C time-series. The level of agreement between the calculated values and the accepted values for d¹³C is within ± 0.05 ‰, and for Δ¹⁴C is within ± 3‰, spanning 200 years. The model contains only seven internal parameters; these are varied to optimize the fit, leading to reasonable parameter values, indicating the validity of the method. In addition, the model shows how a rising CO₂ exchange influx fluctuating with surface temperature is compatible with a nett atmospheric CO₂ sink. The study demonstrates that a single CO₂ residence time applies to both the ¹⁴C bomb pulse and the anthropogenic flux, contrary to the conventional view that "bomb radiocarbon and anthropogenic CO₂ do not behave identically." [Joos 1994 Nature 370, 181–182]. It is shown that the difference in behaviour, claimed to be due to seawater chemistry, is not significant in practice since fluctuating bulk carbon dominates fluctuating isotopic ratio. A new analysis of the airborne fraction indicates that the assumption of a time-dependent exchange influx results in a similar residence time for bulk CO₂ as for ¹⁴C in the nuclear bomb pulse, reinforcing the view that the ¹²C, ¹³C and ¹⁴C carbon isotopic forms of CO₂ behave similarly in the carbon cycle.

Ionizing radiation exposure is known to induce molecular and cellular injury, inflicting a cascade of potentially catastrophic events leading to tissue and organ damage. Metabolomic analysis allows for the identification and quantification of small molecules downstream of genomic changes induced by radiation exposure. We aimed to characterize metabolomic changes that underscore the prefinal stage of lethally irradiated rhesus nonhuman primates (NHPs). Peripheral blood was drawn at baseline, post-exposure as well as at the preterminal stage of NHPs (immediately prior to death in moribund NHPs), which did not survive exposure with 7.2 Gy total-body radiation (LD70/60). Herein, we analyzed global metabolomic changes using ultra-performance liquid chromatography (UPLC) quadrupole time-of-flight mass spectrometry (QTOF-MS) in plasma samples of NHPs collected at various timepoints in relation to irradiation. The overall goal was to identify metabolic shifts present immediately prior to death. Our findings, for the first time, show that radiation induced significant time dependent metabolic perturbations when compared to pre-irradiation samples, particularly in the glycerophospholipid metabolism and steroid hormone biosynthesis and metabolism pathways. These findings provide valuable insights for identifying biomarkers for lethality, which may be helpful for triage during a mass casualty scenario.

A two phase survey of epilepsy was conducted in selected villages in Mundri West and East Counties (26 June−8 July, 2021), an onchocerciasis-endemic area in Western Equatoria State in South Sudan. In the first phase, households were visited by a trained research team to identify persons suspected to have epilepsy. In the second phase, persons suspected to have epilepsy were interviewed and examined by a clinician to confirm the diagnosis. A total of 364 households agreed to participate in the survey, amounting to 2,588 individuals. The epilepsy screening questionnaire identified 91 (3.5%) persons suspected to have epilepsy, of whom in 86 (94.5%) the diagnosis of epilepsy was confirmed by a clinician. The overall prevalence of confirmed epilepsy was 3.3% (95% CI: 2.7-4.1%), and of nodding syndrome 0.9% (95% CI: 0.6-1.4%). In 61 (16.8%) households there was at least one person with epilepsy. Only 1,212 (46.9%) of 2,583 people took ivermectin during the last distribution round in 2021. The annual epilepsy incidence was 77.3/100.000 (95% CI: 9.4-278.9/100,000) and the annual epilepsy mortality 251.2/100,000 (95% CI: 133.8-428.7/100,000). In conclusion, a high prevalence and incidence of epilepsy was observed in villages in Mundri. Urgent action is needed to prevent children from developing onchocerciasis-associated epilepsy by strengthening the local onchocerciasis elimination programme.

Parts I and II of this 3-part series indicated how a global review of both English-language and non-English language papers plus a focus on a lipidosterolic extract of Serenoa repens (LSESr) having a standardized fatty acid profile have together engendered new insights about the biological activity of LSESr vs. LUTS. In this last of a 3-part series, data from the world literature is presented that confirms that LSESr efficacy is the predominant finding in clinical trials. Despite two placebo-controlled clinical trials performed in the U.S. that failed to confirm a benefit of LSESr vs. placebo in LUTS, the global body of the peer-reviewed literature attests not only to efficacy but also to safety. Results will be presented of important trials that compare LSESr to alpha-blockers such as tamsulosin (Flomax®) as well as to 5α-reductase inhibitors such as finasteride (Proscar®) that demonstrate consistent findings of near equivalency between LSESr and these pharmacologic agents. Studies relating data indicative of an additive effect or synergy between LSESr and tamsulosin will be presented as well. The heightened effectiveness of LSESr in men with severe LUTS vs. moderate LUTS expands the importance of our scrutinization of the global literature concerning LSESr. Of great consequence are the contributions of non-English language peer-reviewed publications that have consistently provided evidence of LSESr efficacy in treating LUTS/BPH. These peer-reviewed articles have shown that the effect of LSESr is not that of a placebo. Finally, a comparison of the LSESr extraction products used in the treatment of LUTS, and a discussion of the milieu factors that affect the natural history of LUTS and influence the outcome of clinical trials complete this sedulous analysis of LSESr vs. LUTS.

Given the extent of this global analysis, this report will be presented in three sections. Part I will introduce LUTS. What are the demographics of LUTS? What symptoms are assessed by LUTS and how do we quantify LUTS? Why would a non-prescription item be a valuable consideration in LUTS treatment versus other treatment options? What is basic information about Serenoa repens and what defines a standardized LSESr product? What are the published trials that have affected the acceptability of Serenoa repens in the treatment of LUTS? Finally, a major portion of Part I will discuss the four major reviews of Serenoa repens versus LUTS that have influenced how it is accepted in the USA, in Europe, and other parts of the world. Part I, therefore, lays the groundwork and is foundational for the important findings relating to LUTS and Serenoa repens that will be presented in Parts II and III.

Part I of this 3-part series provided the groundwork for understanding the role of a standardized lipidosterolic extract of Serenoa repens (LSESr) in the treatment of LUTS. It documented that a treatment having a high therapeutic index (i.e., a ratio of benefit to adverse reactions) is a critical need in the demographic context of a rapidly growing elder population. Part I described the clinical symptomatology of LUTS and how it is quantified. A critique of the reports from four authoritative bodies: the European Scientific Cooperative on Phytotherapy (ESCOP), Cochrane 2012, the European Medicines Agency (EMA), and the AUA (American Urological Association) was presented. The foundation above then fine-tuned our search to require (a) consistent evaluability criteria, (b) the quantification of clinical findings, (c) the need to focus on studies employing a standardized LSESr product meeting the fatty acid profile set forth by the European Medicines Agency (EMA) and the US Pharmacopeia and (d) a global assessment of scientific investigations published in all languages and not limited to only English. Part II details the following “new” findings when LSESr vs. LUTS is examined with the above constraints.

Classifying network flow subsequences in an Industrial IoT gateway is an effective method for identifying Industrial IoT faults. This paper proposes a subsequence classification algorithm SSGBUL-IKNN based on unsupervised learning encoding to address the problem of low classification accuracy. Firstly, we built a network module based on unsupervised learning to encode the flow sequence of the Industrial IoT gateway. In the encoding module, a subsequence calibration algorithm controls the increasing error during the coding process. Then, the specific fault type is obtained through an improved KNN classification algorithm based on the indication distance source from the integrated coding sequences converted by multi-dimensional network flow sequences. The test result on three Industrial IoT datasets of a sewage treatment plant shows that the accuracy of SSGBUL-IKNN in this paper exceeds 92%, significantly higher than the algorithm DTW and TSF. It reaches the classification requirements of Industrial IoT fault diagnosis.

The Krudum granite body comprises highly fractionated granitic rocks ranging from medium-F biotite granites to high-F, high-P₂O₅ Li-mica granites. This unique assemblage is an ideal site to continue recent efforts in petrology to characterize the role of zircon, monazite and xenotime as hosts to REEs. The granitic rocks of the Krudum body analysed in this study were found to contain variable concentrations of monazite and zircon, while xenotime was only found in the high-F, high-P₂O₅ Li-mica granites and in the alkali-feldspar syenites of the Vysoký Kámen stock. For analysed monazites of all magmatic suites cheralite substitution was significant. The highest concentration of cheralite was found in monazites from the high-F, Li-mica granites and from the alkali-feldspar syenites. The proportion of YPO₄ in all analysed xenotimes ranges from 71 to 84 mol. %. Some xenotimes were found to be hydrated and the observed water content estimated from analytical data ranged from 5 to 11 wt. % H₂O. Analysed xenotimes were commonly enriched in HREEs (9.3– 19.5 wt. % HREE₂O₃) and thorite-coffinite and cheralite exchange was observed. Analysed zircons from granite suites of the Krudum granite body contained moderate Hf concentrations (1.0–4.7 wt. % HfO₂; 0.010–0.047 apfu Hf). The highest concentrations of HfO₂ were found in zircons from the high-F, high P₂O₅ Li-mica granites (1.2–4.7 wt. % HfO₂) and from the alkali-feldspar syenites (1.3–4.1 wt. % HfO₂). Zircons from the high-F, high-P₂O₅ Li-mica granites were often hydrated and fluorised. The concentrations of F in zircon from partly greisenised high-F, high-P₂O₅ Li-mica granites reached up to 1.2 wt. % (0.26 apfu F). In zircons from the alkali-feldspar syenites enrichment in P, which is not associated with a simultaneous enrichment in Y + REE, was also observed. Analysed zircons from the high-F, high P₂O₅ Li-mica granites were enriched in Y (up to 5.5 wt. % Y₂O₃; 0.10 apfu Y) and Sc (up to 1.17 wt. % Sc₂O₃; 0.03 apfu Sc).

Drug hypersensitivity reactions (DHR) to platinum-based compounds (PC) are on the rise, and their personalized and safe management is essential to enable first-line treatment of these cancer patients. This study aimed to evaluate the usefulness of basophil activation test by flow cytometry (BAT-FC) and the newly developed sIgE-microarray and BAT-microarray in diagnosing IgE-mediated hypersensitivity reactions to PC. 24 patients with DHR to PC (20 oxaliplatin and four carboplatin) were evaluated: 13 patients diagnosed as allergic with positive skin tests (STs) or drug provocation tests (DPTs), six patients diagnosed as non-allergic with negative STs and DPTs, and five patients classified as suspected allergic because DPTs could not be performed. In addition, four carboplatin-tolerant patients were included as controls. BAT-FC was positive in 2 of 13 allergic patients, with a sensitivity of 15.4% and specificity of 100%. However, the sIgE- and BAT-microarrays were positive in 11 of 13 DHR patients, giving a sensitivity of over 84.6% and a specificity of 90%. Except for one patient, all samples from the non-allergic and control group were negative for the sIgE- and BAT-microarrays. Our experience indicates that sIgE- and BAT-microarray could be helpful in the endophenotyping of IgE-mediated hypersensitivity reactions to PC and may provide an advance in decision-making for drug provocation testing.

Background and Objectives. Prevalence of GERD is increased among individuals with obesity and RYGB is considered as the most effective procedure to control GERD and obesity. However, some patients continue to have GERD after RYGB. The aim of the study was to investigate the prevalence and the risk factors of GERD after RYGB. Material and Methods. This prospective study included 180 patients operated with RYGB and followed for on average of 12.2 (0.6) years. 126 (70%) patients agreed to participate in online consultations and provided data on weight, GERD symptoms, filled GERD-HRQL, TFEQ-18 and GSRS questionnaires. Results. The average age before surgery was 42.7 (10.5) years and BMI was 45.2 (6.4) kg/m2. 128 (71.1%) were females and preoperative GERD was diagnosed in 74 (41.1%) patients. At 12 years follow-up the mean %EBMIL and %TWL were 60.37 and 25.73, respectively. The median %WR was 18.0 (39.0). The GERD was present in 30 (23.8%) patients, of whom 12 (40%) continued to have GERD symptoms and 18 (60%) developed de novo GERD. The GERD-HRQL score significantly decreased from 3.0 (8.0) at baseline to 2.0 (5.0) (p=0.028) at 12 years. GSRS Diarrhea and Indigestion median scores increased significantly, from 1.33 (0.67) to 1.5 (2.42) (p 3.2.

Multiple drugs administration is a common practice in hospitals and clinics. This is the case when heavy pathologies are treated. In this context, frequently, antivirals and antibiotics are co-administrated either simultaneously or sequentially ignoring potential incompatibilities. In this study, we focused on an antiviral (Acyclovir) and an antibiotic (Ciprofloxacin) compatibility/incompatibility when they co-administrated with special interest on the effect of drugs ratio, pH and delay. By implementing robust HPLC method, we determined the main factors leading to potential modification of concentration of one of the two drugs in the mixture. The results showed that acyclovir is quantitatively recovered in all conditions related to pH, concentration and time (up to 24 hours). However, ciprofloxacin is strongly altered in acidic and basic conditions, the quantity of ciprofloxacin and time after mixing the two drugs. The most valuable piece of information is that the ratio of acyclovir/ciprofloxacin is crucial. The latter should be calculated and managed to provide at least two fold quantity of acyclovir versus ciprofloxacin in order to maintain the administrated doses and warrant efficient therapeutic effect.

A series of (benzoimidazol-2-ylmethyl)amine palladium(II) complexes have been employed as catalysts in the homogenous hydrogenation of alkenes and alkynes under mild conditions. A correlation between the catalytic activity and the nature of the ligand was established. Kinetic studies of the hydrogenation reactions of styrene established pseudo-first-order dependence on styrene substrate. On the other hand, partial orders with respect to H2 and catalyst concentrations were obtained consistent with the formation of palladium(II) monohydride species as the active species. The nature of the solvent used influenced the hydrogenation reactions, where coordinating solvents resulted in lower catalytic activities. Density functional theory investigations provided valuable insights into the reactivity trends and influence of complex structure on the hydrogenation reactions.

The links between mindfulness, savoring positive experiences, and depressive symptoms have been well-established in the literature. Nevertheless, little has been done to disentangle the prospective relations among these constructs. Clarifying the longitudinal relations is crucial, as it enables researchers and practitioners to discern potential trajectories of mental health interventions. In this study, 180 emerging adults between 18 and 27 years old were recruited twice at 3 months apart to complete self-reported measures including mindfulness, savoring positive experiences, and depressive symptoms. Cross-lagged path analysis indicated that savoring the moment was predictive of mindfulness three months later, whereas depressive symptoms were predictive of both mindfulness and savoring the moment three months later, above and beyond the effects of age, gender, and family income. Additionally, mindfulness, savoring positive experiences, and depressive symptoms were significantly correlated at baseline. The present study evidenced short-term inversed effects of depressive symptoms on mindfulness and savoring the moment, as well as a positive effect of savoring the moment on mindfulness. Hence, interventions gearing towards symptom reduction of depression are likely to carry concurrent and prospective benefits of psychological functioning, namely the ability to be present in the moment and to savor. Taken together, reducing depressive symptoms may be crucial in fostering psychological well-being.

Fractal array antennas are multiband arrays having ultra wide band and space filling facility. But Side lobe levels and large number of antenna elements are the major designing challenges of these arrays. In this paper, design and analysis of octagonal fractal array antenna is investigated with Morse-Thue fractal density tapering technique (MTFDT). Due to the proposed technique, a remarkable improvement has observed in Side lobe levels and thinning of the elements can also be attained at the various iterations of octagonal fractal array antenna. These arrays are analyzed and simulated by MATLAB-15 programming.

This research investigates the complex transformation of the Baltic Clean and Dirty Tankers markets from 1998 to 2023. Our study quantifies the market multifractality in two distinct periods, from 1998 to 2010 and 2010 to 2023. We compare multifractal measures of the original, surrogated, and shuffled data, which indicate high multifractality and a complex market structure influenced by temporal organization and inherent volatility. Shuffled data analysis emphasizes the critical role of temporal sequences within market behaviour. Additionally, the study delves into external factors such as regulatory changes, economic disturbances, technological innovation, and environmental concerns contributing to market complexity. A distinct shift in multifractal values between the two periods suggests an evolution from crisis-induced complexities to a market influenced by diversified and modern dynamics. Our findings offer a concise understanding of the multifractal nature of the tanker markets and how global crises can impact the markets, emphasizing the importance of considering systemic risks in freight market analysis.

AbstractLocal estimates of coastal flood risk are required for coastal planning and development, including the location and design of sea-defences and coastal buildings, such as harbours and associated infrastructure. This paper discusses the use of three parameters associated with estimating such risks; the flood return period, the instantaneous flood probability and the flood design risk, and it describes the mathematical background for their derivation. The discussion is extended to include the effects of sea level rise and how it can be incorporated into the calculations. Flood height can vary quite rapidly with distance along the coast, being affected by coastal topology, which may magnify or diminish the tidal and surge effects. Similarly land heave influences the local effects of sea level rise and can be influenced by water extraction, tectonic movements and melting ice. Tide gauge measurements provide a local historical record from which the various parameters can be retrieved. This paper discusses the algorithms used to derive these measures from tide-gauge records. The figures have been derived for four tide gauges located on the UK east coast.

Detecting cracks in teeth is a clinical challenge. Patients may complain of diffuse pain on chewing, pain, at times, on temperature change and pain that occurs episodically. Common diagnostic tools such as radiographs and visual examination may not detect cracks. This case report shows how PTR-LUM in The Canary System can detect cracks in teeth not seen with other devices. In this clinical situation, the crack involved a portion of the mesial and distal surfaces of a mandibular second molar.

The objective was to conduct a scoping review and produce a publicly available database characterizing the design and reporting elements of the literature on dietary added sugars and select health outcomes. Relevant studies published from 1990 – 2021 were identified to create a database containing information on study and population characteristics, reported added sugars source and concentrations, diet energy balance, total energy intake, and outcome measures related to body composition, obesity, cardiovascular disease, and diabetes mellitus. There were 245 publications identified, 22% of which describe interventions and 78% describe observational studies. Publications pertaining to added sugars have risen dramatically since 2010, led by studies primarily assessing body composition (36%) or cardiovascular health (32%), including adults (65%), measuring liquid-only sources of added sugars (56%). Over 65% of studies reported total energy intake, 61% controlled for total energy intake in the design and analysis, and fewer than 5% of studies reported the energy balance of subjects. There has been a significant increase in research on added sugars since 2010, with substantial heterogeneity across all facets of methodology – study designs, exposures and outcomes of interest, terminology, and reporting of dietary intake data – thus limiting the ability to synthesize evidence in this scope of literature. This evidence map highlights gaps and important areas for improvement to strengthen the state of research to better inform future policies and dietary recommendations on added sugars.

What is the ideal soil-grass combination for maximum photosynthesis? In this study, we investigated how soil and grassland types affect photosynthesis in the grasslands of Gannan, China. We divided the grasslands of Gannan into 166 study sites, each with a unique soil-grass combination by intersecting the soil and ecoregion maps using ArcGIS. We obtained 19 years of data on the Net Photosynthesis (PsnNet) of grasslands in the area from 2000 to 2018 and then divided them into “growing season” (June to September) and “non-growing season” (October top May). Between 2000 and 2018, PsnNet of grasslands showed a gradually increasing trend. The effect of soil type on PsnNet was not significant during the growing season. However, it was highly significant during the non-growing season. Among the soil types, grasses that grew in Mollic, Gelic, and Haplic soils had the highest rate of photosynthesis. The difference in PsnNet among the various grass types was highly significant during both seasons. However, Tropical and Subtropical succulent evergreen broad-leaf shrubs and Temperate meadows had the highest rate of photosynthesis. Additionally, there was a highly significant difference in PsnNet among the various soil-grass interactions. In the growing season, TStEgBLS growing Eutric soils had the highest PsnNet. However, SaDBLS growing in Gelic soils had the the highest.

Asphaltene precipitation and deposition pose significant operational challenges in both reservoirs and surface facilities by inducing formation damage. To understand the kinetics involved in asphaltene particle nucleation, growth, and aggregation, this study employed confocal microscopy and centrifuge-based methods under a unified set of experimental parameters. The acquired time-resolved particle size images were analyzed using MIPAR image processing software, while asphaltene mass yield was quantitatively evaluated through centrifugation. Experimental conditions were varied to study the effects of heptane concentration, asphaltene concentration, and shear rate. Notably, this investigation introduces, for the first time, the parameter of particle count as an additional variable influencing asphaltene mass production. This study aims to discern how particle count correlates with asphaltene mass yield over time. Results indicate that the minimum mean particle diameter was observed to be 2 microns, which progressively grew up to 80 microns. The mean particle diameter exhibited a positive correlation with both asphaltene concentration and shear rate, whereas an inverse correlation was seen with heptane concentration. Furthermore, the asphaltene mass yield was found to increase with greater asphaltene and heptane concentrations, as well as with higher shear rates. The relationship between mean particle diameter and mass yield was found to be nonlinear. In the early stages, a higher prevalence of small particles contributed to a greater total particle count, while at later stages, particle aggregation led to the formation of larger particles that influenced the overall asphaltene mass. The insights gained from understanding the relationship between particle diameter, count, and mass yield are crucial for advancing the fundamental science of asphaltene precipitation and deposition. These findings may also guide future research that relies solely on particle counts for assessing asphaltene deposition.

Gut bacteria play an important role in several metabolic processes and human diseases, such as obesity and its co-morbidities, like fatty liver disease, insulin resistance/diabetes and cardiovascular events. Among several factors, dietary patterns, probiotics, prebiotics, synbiotics, antimicrobials and non-dietary factors, such as stress, age, exercise and climatic conditions, can dramatically impact the human gut microbiota diversity and equilibrium. However, the effect of minor food constituents, including food additives and trace contaminants, on human gut microbiota has received less attention. Consequently, the present review aimed to provide an objective perspective of the current knowledge regarding the impacts of minor food constituents on human gut microbiota and consequently, on human health.

The species composition of vultures and their interactions on carcasses of various stages of decomposition is not well understood yet it potentially affects their food acquisition and survival. We collected data from six carcasses between June and December 2021 using camera traps that were set on carcasses undergoing various decomposition states in Sinamatella Camp of Hwange National Park, Zimbabwe. Of interest were the cases in which each vulture species was dominating in interactions which gave it an advantage in terms of food acquisition. Four vulture species were observed (White-backed, White-headed, Lappet-faced and Hooded Vultures). Vulture abundances were greatest on fresh carcasses and least on dry ones. Although dominance behaviors by the White-backed and White-headed Vultures were recorded over all other vulture species, there were no records of the Lappet-faced dominating other vultures. In addition, the Hooded Vultures were mostly dominating non-vulture avian species on advanced decay carcasses. Our results demonstrate how various species may be prone to intense competition that may further place them at disadvantageous positions if food sources decline, more so under climatic shifts and various anthropogenic pressures.

In order to search possible residual minor phases in Y-Ba-Cu-O family, powdered mixtures of Y₂O₃ + BaCO₃ + CuO and, independently, superconducting compound YBa₂Cu₃O_7-x have been treated in evacuated cells and elevated temperatures.YBa₂Cu₃O_7-x was reduced to YBa₂Cu₃O₅ by use of the special home designed Taconis-Knudsen vacuum device. A subsequent doping by oxygen converts produced insulator YBa₂Cu₃O₅ to semiconductor or metal YBa₂Cu₃O_5+x (0<x<0.3). In addition to YBa₂Cu₃O₅, 0.05 volume percent of the minor delafossite phase Y₂Cu₂O₄ was being spotted in the powder mixture 1/2 Y₂O₃ + 2BaCO₃+6Cu₂O, heated up to 818 °C in an inert gas atmosphere. An attempt to prepare the insulating bulk delafossite samples was successful, and subsequent doping by oxygen produces novel metallic phases.

This study uses a mass-spring-damping system to simulate the repeated strain of liquefaction cyclic triaxial tests. The two results are compared in this paper to understand the feasibility of the mass-spring-damping system developed in this paper and the feasibility of future research on this related topic and development potential. The main factors affecting this mode's repeated strain are the spring coefficient k and the external force Q0. The spring coefficient has an inverse relationship but does not increase in multiples. The external force has a direct proportional relationship but does not increase the result- a non-multiple increase. When the pore water pressure of the liquefied cyclic triaxial test specimen rises, it will cause the specimen to liquefy, decreasing effective stress, shear modulus G, and damping ratio D, causing an increase in strain. The shear modulus and damping ratio are related to the spring coefficients k and c. Both are variables that change with time. This article takes an original thin-tube specimen at point A in the Yunlin area in Taiwan as a testing example. Through Mathematica software, it can be obtained that the mass m=1kg, the spring coefficient k=244e-0.1t kgf/cm, and the damping coefficient c=0.739e-0.257t kgf-s/cm and external force Q0=10.1sin2πt kg; Finally, this study selected the original thin-tube specimens from four locations in the Yunlin area, and simulated the repeated strain amount of the cyclic triaxial test specimens through a spring-damping system. The results show that the spring-damping system is feasible for simulated cyclic triaxial tests because the model is simple and the parameters are easy to understand and obtain, which also shows the extensibility of this model. Preliminary results of the research show that this model can further simulate the repeated strain obtained by cyclic triaxial tests without considering the increased trend in pore water pressure and the decrease in effective stress during cyclic loading.

A novel means of applying radiotherapy in cancer treatment is the application of the radiation dose at a very high intensity for a very short time, FLASH radiotherapy (FLASH-RT). This technique involves exposure of tumors to >40 Gy/s, usually for less than one second. Studies conducted in cell and preclinical models suggest that FLASH-RT seems less damaging to normal tissues from adverse effects, relative to the same overall dose of radiation administered in conventional therapy (CONV-RT) which involves administration of lower levels of radiation repeated intermittently over a protracted period. In contrast, the susceptibility of tumor tissues to FLASH-RT is not diminished relative to CONV-RT. Within solid tumors both modes of dispensation of radiation produce an equivalent degree of cell damage. This differential between normal and malignant material has been found in isolated tissues, animal studies, and more recently in clinical trials. However, the classical radiation concept is that high energy linear transfer radiation (LET) is more damaging than the equivalent total dose of low LET. Thus, the susceptibility of cells should be greater to short-term exposure to high LET. This article discusses the potential reasons that may account for this discrepancy. While the relative protection given to untransformed tissues by FLASH-RT relative to tumor tissue is a major step forward in radiation therapy of cancer, the processes that lie behind this phenomenon are incompletely understood and are considered here.

Perovskite Solar Cell (PSC) is a third-generation photovoltaic device known for its rapid improvement in efficiency levels over the past decade. Moreover, the added benefits of abundant sourcing of raw materials, uncomplicated fabrication process, organic and inorganic device materials, and tuneable bandgaps make this technology a sustainable energy alternative. However, the efficiency values of these devices are subjected to variation depending on factors such as material compatibility, environmental conditions, energy band alignment of device components and stability characteristics to extrinsic and intrinsic factors. One such vital intrinsic factor is film morphology, homogenous and superior film quality formation and pinhole and trap-free films. In this study, we have investigated the formation of perovskite films on a qualitative basis using metal chloride washing of salts such as Erbium, Antimony, Cadmium and Chromium Chloride. The study aims to analyse the difference in film formation with various metal chloride washing and how this could potentially impact or contribute to photovoltaic performance if the devices are fabricated.

In developing countries today, population growth and the penetration of higher standard of living appliances in homes has resulted in a rapidly increasing residential load. In South Africa, the recent rolling blackouts and electricity price increase only highlighted this reality calling for sustainable measures to reduce the overall consumption and peak load. The dawn of the smart grid concept, embedded systems and ICTs have paved the way to novel HEMS design. In this regard, the Internet of Things (IoT), an enabler for smart and efficient energy management systems is seeing increasing attention for optimizing HEMS design and mitigate its deployment cost constraints. In this work, we propose an IoT platform for residential energy management applications focusing on interoperability, low-cost, technology availability and scalability. We focus on the backend complexities of IoT Home Area Networks (HAN) using the OCF IoTivity-Lite middleware. To augment the quality, servicing and reduce cost and complexities, this work leverages open-source Cloud technologies from Back4App as BaaS to provide consumer and Utilities with a data communication platform within an experimental study illustrating time and space agnostic “mind-changing” energy feedback, Demand Response Management (DRM) and appliance operation control via a HEM App via an Android smartphone.

The three-pronged sliding universal coupling is a new kind of three-pronged coupling. To study its kinematic and dynamic characteristics, directional cosine matrices are utilized as tools to analyze the coordinate systems by establishing simplified geometric models and corresponding motions. Through the analysis of the motions of the input and output shafts and employing the method of single-force element, a set of equilibrium equations for the forces acting on the output shaft and the input shaft are formulated for solution analysis. The research indicates that during the rotation process, there exists a small angular difference between the input shaft and the intermediate shaft, demonstrating the quasi-constant angular velocity characteristics of the new tripod sliding universal coupling. The curves of the forces and torques acting on each component of the coupling approximate sinusoidal curves. The optimal operating angle range for the new tripod universal coupling is at angle , during which the system exhibits good transmission and mechanical performance.

This study provides a comprehensive investigation of lactic acid bacteria (LAB) isolated from Argentinean Capsicum annum L. The research covers important aspects, including genotypic characterization, bacterial stress tolerance, adhesion ability, safety evaluation, and functional and technological properties. The predominant isolates were identified as Lactilactobacillus curvatus and Lactiplantibacillus plantarum. Rep-PCR analysis grouped the isolates into 11 clonal groups. Lp. plantarum LVP 40 and LV 46; Levilactobacillus brevis LVP 41, Pediococcus pentosaseus LV P43, and Lt. curvatus LVP44, displayed both safety and resilience against adverse conditions such a slow pH, bile, and simulated gastric and intestinal juices. Moreover, the LAB strains exhibited high hydrophobicity and auto-aggregation percentages, NaCl tolerance, and substantial acidifying capacity. LAB supernatants demonstrated promising surfactant and emulsifying properties. Likewise, they differentially inhibited Staphylococcus aureus and Pseudomonas aeruginosa biofilms, showcasing their potential as antipathogenic agents. Noteworthy some strains displayed considerable co-aggregation with these pathogens, and several isolates showed an effective antimutagenic and detoxifying power, further emphasizing their multifaceted capabilities. Five pepper bacterial strains showcased probiotic properties, suggesting their potential for gut health enhancement. In summary, these LAB strains hold promise as vegetable fermentation starters, contributing to food safety and versatile applications in food science.

This review describes how resonance in amides is greatly affected upon substitution at nitrogen by two electronegative atoms. Nitrogen becomes strongly pyramidal and resonance stabilisation, evaluated computationally, can be reduced to as little as 50% that of N,N-dimethylacetamide. However, this occurs without significant twisting about the amide bond, which is borne out both experimentally and theoretically. In certain configurations, reduced resonance and pronounced anomeric effects between heteroatom substituents are instrumental in driving the HERON (Heteroatom Rearrangement On Nitrogen)^† reaction, in which the more electronegative atom migrates from nitrogen to the carbonyl carbon in concert with heterolysis of the amide bond, to generate acyl derivatives and heteroatom-substituted nitrenes. In other cases the anomeric effect facilitates S­_N1 and S_N2 reactivity at the amide nitrogen.

Broflanilide is a novel active ingredient from a unique insecticide class (IRAC Group 30) and was investigated as a control option against modern insecticide resistant strains of the common bed bug, Cimex lectularius. The susceptibility of technical grade broflanilide and efficacy of a broflanilide-based aerosol formulation (Earth Corp., Japan) were evaluated against five C. lectularius strains (MONH, SYD, DARL, PARRA, RIPPO). Results demonstrated that bed bugs had high susceptibility to broflanilide (RR50: SYD=1.22-fold, DARL=1.03-fold, PARRA=3.65-fold, RIPPO=2.77-fold), compared to the susceptible MONH strain. The aerosol showed high efficacy to adult bed bugs (97.5–100 % mortality to five strains after 24 hrs post-spray) and produced a notable decrease in egg hatch rates (MONH=9.7–23.4 %, PARRA=14.9–22.6 %). The aerosol also demonstrated high residual activity with 97.5–100% mortality in all five bed bug strains within 7 days exposure. The impact of different surface types upon aerosol residual efficacy was limited, although residues on a non-porous surface (tile) killed bed bugs slightly quicker than that on a porous surface (filter paper). The aerosol provided long residual activity to bed bugs, as 6-month-old residues were as equally efficacious to that of fresh residues. Bed bugs did not avoid surfaces treated with the aerosol. The high efficacy (including ovicidal efficacy), long residual activity, and non-avoidance of bed bugs on treated surfaces, demonstrated that broflanilide is highly suitable for modern bed bug management.

The aim of our study was a comprehensive comparative assessment of the effect of consumption of 1 and 2% cholesterol as part of a standard diet with and without regular moderate physical activity on the main biomarkers of lipid and cholesterol metabolism, as well as the intestinal microbiota of male Wistar rats. The animals were randomly divided into 5 groups according to body weight and Open Field test results: Control (n=10), 1% Chol (n=10), 2% Chol (n=10), 1% Chol + RUN (n=10) and 2% Chol + RUN. The cholesterol was additionally added in the amount of 1g or 2g/100g, respectively, to the diet of animals. The rats of experimental groups 1% Chol + RUN and 2% Chol + RUN were subjected to regular (2 days a week) physical activity on a Treadmill. In rats of four experimental groups, when compared to the Control, a response of 39 indicators was revealed. The largest number of changes in biomarkers - 29 (statistically significant, p

This review examines the categorization of Essentially Derived Varieties (EDV) introduced in the 1991 revision of the Convention of the Union internationale pour la protection des obtentions végétales (UPOV). Challenges in the implementation of the concept and progress made on a crop-by-crop basis to provide greater clarity and more efficient implementation are reviewed. The current approach to EDV remains valid provided i) clarity on thresholds can be achieved including through resource intensive research on an individual crop species basis and ii) that threshold clarity does not lead to perverse incentives to avoid detection of essential derivation. However, technological advances leading to new varieties resulting from the simultaneous introduction or change in expression of more than “a few” genes will so challenge the concept to require a new Convention. Revision could include deletion of the concept of essential derivation and revision on a crop-by-crop basis of the breeder exception. Countries that allow utility patents for individual plant varieties per se should consider removing that possibility unless plant breeders utilize those encouragements for risk taking and investment to broaden the germplasm base upon which the long-term sustainability of plant breeding resides.

Employing remote sensing techniques to evaluate crop residue cover (CRC) enables rapid mapping of tillage practices over large cropland areas, which has significant practical implications for monitoring the implementation of conservation tillage practices. This research utilized Sentinel-2 MSI and Landsat-8 OLI remotely sensed data, various spectral indices were calculated and the datasets were correlated with the field-measured CRC data. Selected spectral indices, highly significantly correlated, were chosen to build a correlation model between the indices and the CRC. Considering Sentinel-2 MSI and Landsat 8 OLI remotely sensed data variations in spectral and spatial scales, the accuracy of CRC models was evaluated using R2 and RMSE values. From the results, it's evident that all six spectral indices, including STI, NDTI, SRNDR, NDI5, NDI7 and NDSVI, registered correlation coefficients with the CRC exceeded 0.3 in the study area. STI and NDTI showed a stronger correlation to CRC, with coefficients of 0.810 and 0.803, respectively. For the Landsat 8 data, the lowest correlation obtained was for NDSVI with the Landsat 8 data with a correlation coefficient of 0.358. Applying the linear regression technique, STI and NDTI obtained higher accuracy compared to other indices in the Sentinel-2 MSI data. For NDTI and STI, The R2 values were 0.650 and 0.665, respectively, while their corresponding RMSE values were 3.96% and 4.03%. The highest model accuracy was obtained for the STI and NDTI constructed from the Landsat 8 OLI data (R2 values 0.41 and 0.40; RMSE values 5.25% and 5.27%, respectively). The CRC model built using partial least squares regression (PLSR) exhibited greater precision when applied to the Sentinel-2 MSI data (R2 value 0.894; RMSE value 2.18%) in comparison to the Landsat 8 OLI data (R2 value 0.695; RMSE value 3.70%). PLSR has the potential to enhance the precision of the model. In addition, the study area shows that the estimation of the CRC is better in the one-dimensional linear regression model and the PLSR model created with the Sentinel-2 MSI optical data compared to the Landsat 8 OLI optical remotely sensed data. The validation suggests that the CRC estimation in the study area is more precise when using the model relying on Sentinel-2 satellite imagery rather than the Landsat 8 OLI imagery.

Potato virus Y (PVY) is one of the most important constraints to potato production worldwide. There is an increasing occurrence of recombinant PVY strains PVYNTN and PVYN-Wi and a decline in the incidence of the nonrecombinant PVYO. We hypothesized that this may be due to the ability of these recombinant strains to antagonize and/or outcompete PVYO in mixed infections. To deter-mine this, we investigated interactions between PVYO and three recombinant PVY strains com-mon in North America: PVYNTN, PVYN-Wi, and PVYN:O. Overall, our study showed that these inter-actions are tissue dependent. Specifically, PVYNTN, the main causal agent of potato tuber necrotic ringspot disease (PTNRD), was found to be more adaptable than PVYO, especially in potato leaves due, at least in part, to the Ny gene that confers hypersensitive resistance (HR) to PVYO. Further-more, PVYN-Wi was found to repress PVYO in potato tubers but act synergistically in potato leaves. The PVYO-induced foliage necrosis in cultivar ‘Ranger Russet’ was observed to be more severe in plants co-infected by PVYN-Wi and PVYN:O, respectively, resulting in plant death. Strikingly, this PVYO -induced necrosis was suppressed by PVYNTN in doubly infected plants. These interactions may, at least partially, explain the decreasing incidence of PVYO in United States potato produc-tion regions, especially given that many cultivars contain the Ny gene, which likely limits PVYO enabling PVYNTN and PVYN-Wi to outcompete. We also found that replication and cell-to-cell movement of these PVY strains in tubers at 4C was similar to levels at ambient temperature.

ZrO2-YO1.5-TaO2.5(ZYTO) composite ceramic is considered to be the candidate of next generation of thermal barrier coatings as its excellent thermal stability and low thermal conductivity in high temperature, however, the mechanical properties and fracture tougheness of ZYTO system may be the shortcomings compared with the 8YSZ. In this study, ZYTO composite ceramics were successfully prepared by chemical coprecipitation reaction, the microsture of resulting composites were studied as a function of doping of M-YTaO4. Mechanical properties, including the density, porosity, hardness and Young's modulus, are determinate; the toughening mechanism were verified by the crack growth behavior of Vickers indentation test Results suggested that M-YTaO4 refines the fluorite phase grain and strengthens the grain interface in the composite ceramic. The thermal mismatch between the second phase and matrix produces residual stress in the bulk and affects the crack propagation behavior. With the increase of M-YTaO4 doping, the grain coarsening and ferroelastic domains are observed in the experiments. The ferroelastic domains with orthogonal polarization directions near crack tip evidences the ferroelastic toughening mechanism. The competition among these crack behaviors, such as cracks deflection, bridging and bifurcation, dominates the actual fracture toughness of the composite. The best toughening formula is determinate in the two-phase region and the highest fracture toughness is about to 3.1MPa·m1/2. Above all, mechanical properties of ZYTO composite ceramics look potential for thermal barrier coatings materials.

Panax notoginseng is a traditional Chinese medicine, and saponins are its main active ingredients. The content of saponins in flower of P. notoginseng is the highest in the whole plant. Minor ginsenosides have stronger pharmacological activity than main ginsenosides, but its content in nature is very low. We can use extracted total saponins from P. notoginseng flower as the substrate to produce minor ginsenosides by biotransformation method. In this study, we used the fungus Talaromyces flavus and its crude enzymes to transform the extracted total saponins of P. notoginseng flower. Through the qualitative and quantitative analysis of the transformation substrates and products, it was found that minor ginsenosides Gyp-XVII, ginsenosides C-Mc1, C-Mx1, F2, Rg3, 20(R)-Rg3, Rk1 and Rg5 were found in the products and the conversion rate of the major saponins in P. notoginseng flower ranged from 44.16 to 55.22%, the yields of the minor ginsenosides ranged from 0.05 to 3.24%. This study provided a good experimental idea, greatly increased the utilization rate of total saponins in P. notoginseng flower, and laid a foundation for promoting the wide application of minor saponins.

Systemic inflammation plays a central role in many diseases and is, therefore, an important therapeutic target. In a scoping review, we assessed the evidence base for anti-inflammatory effects of pre-, pro- and synbiotics in children. Of 1254 clinical trials published in English in Ovid Medline and Cochrane Library PubMed from January 2003 through September 2022, 29 were included in the review. In 6 studies of healthy children (n=1552), one reported that fructo-oligosaccharides added to infant formula significantly reduced pro-inflammatory biomarkers and one study of a single strain probiotic reported both anti- and pro-inflammatory effects. No effects were seen in the remaining two single-strain and one multi-strain probiotic and one synbiotic study. In 23 studies of children with diseases (n=1550), prebiotics were tested in 3, single-strain in 16 and multi-strain probiotics in 6 and synbiotics in 2 studies. Significantly reduced inflammatory biomarkers were reported in 7/10 studies of atopic/allergic conditions, 3/5 studies of auto-immune diseases, 1/2 studies of preterm infants, 1 study of overweight/obesity, 2/2 studies of severe illness and 2/3 studies of other diseases. However, often only one or two of several biomarkers were improved, increased pro-inflammatory biomarkers occurred in 5 of these studies and a probiotic increased inflammatory biomarkers in a study of newborns with congenital heart disease. The evidence base for the effects of pre-, pro- and synbiotics on systemic inflammation in children is weak. Further research is needed to determine if anti-inflammatory effects depend on the specific pre-, pro- and synbiotic preparations, health status and biomarkers studied.

Superconducting split ring resonator arrays allow to overcome two main limitations affecting metallic metamaterial resonating in the Terahertz (THz) range: Ohmic losses and tunability of their optical response. In this work, we design and experimentally realize direct and complementary square arrays of superconducting YBa2Cu3O7 (YBCO) split ring resonators working in the THz spectral range. The main purpose of this paper is to show how the metamaterial resonances can be tuned by temperature (T) when crossing the superconducting transition temperature Tc of YBCO. The tuning property can be quantified by describing the THz transmittance of the patterned YBCO films vs. T through a model of coupled resonators. This model allows us to estimate the THz resonances of split-ring arrays and their interaction, showing how the kinetic inductance Lk in the superconducting state is the main parameter affecting the metamaterial properties.

Despite the partial disclosure of driving scenario knowledge graphs, they still fail to meet the comprehensive needs of intelligent connected vehicles for driving knowledge. Current issues include the high complexity of pattern layer construction, insufficient accuracy of information extraction and fusion, and limited performance of knowledge reasoning models. To address these challenges, a hybrid knowledge graph method was adopted in the construction of the Driving Scenario Knowledge Graph (DSKG). Firstly, core concepts in the field were systematically sorted and classified, laying the foundation for the construction of a multi-level classified knowledge graph top-level ontology. Subsequently, by deeply exploring and analyzing the Traffic Genome data, 34 entities and 51 relations were extracted and integrated with the ontology layer, achieving the expansion and updating of the knowledge graph. Then, in terms of knowledge reasoning models, an analysis of the training results of the TransE, Complex, Distmult, and Rotate models in the entity linking prediction task of DSKG revealed that the Distmult model performed the best in metrics such as hit rate, making it more suitable for inference in DSKG. Finally, a standardized and widely applicable Driving Scenario Knowledge Graph was proposed. The DSKG and related materials have been publicly released for use by industry and academia.

Multi-morbidity and polypharmacy are common in older people and pose a challenge for health and social care systems especially in context of global population ageing. They are complex and interrelated concepts in the care of older people that require early detection and patient centred decision making that are underpinned by the principles of multidisciplinary led comprehensive geriatric assessment (CGA). Personalised care plans need to remain responsive and adaptable to the needs of a patient, enabling an individual to maintain their independence.

Background: Cytokines and chemokines are critical regulators of innate and adaptive immunities during viral infection. We examined innate and adaptive immune responses to hepatitis C virus (HCV) and hepatitis B virus (HBV) at baseline and against controls. Methods: Twenty-seven cytokines were evaluated before treatment in 27 patients with chronic hepatitis C(CHC) [genotype1 (n=20), genotype2 (n=7), HCVRNA 5.72IU/ml] and 12 chronic hepatitis B(CHB) [e-antigen (Ag) (+) (n=5), e-Ag (-) (n=7), HBVDNA 6.191.31Logcopies/ml] and against controls(n=5). Results: Th1 and Th2 cytokines were significantly higher (p<0.05) in CHB than in CHC. The levels of IL-IL10 in CHC and CHB, and IL15 in CHC(genotype2) and CHB were significantly lower (p<0.05) than in controls. The levels of CXCL8 in CHC and CHB, IL12 in CHC and CHB [e-Ag (-)] and CXCL10 in CHC and CHB were significantly higher (p<0.05) than in controls. IFN-γwas higher in CHB than in controls. Conclusion: Cytokines levels differed between CHB and CHC before treatment. Innate immune responses were impaired in CHB with HBeAg(-) and CHC, but not in CHB with HBeAg(+) with high viral loads. Adaptive immune responses were impaired in CHB and CHC and appear to reflect the distinct state of virus-host immune interactions between CHB and CHC.

The International Roughness Index (IRI) is the standard scale for evaluating road roughness in many countries in the world. The Taipei City government actively promotes a Road Smoothing Project and plans to complete the rehabilitation of the main and minor roads within its jurisdiction. This study aims to detect the road surface roughness in Taipei City and recommend appropriate IRI thresholds for road rehabilitation. A total of 171 asphalt concrete pavement sections in Taipei City with a total length of 803.49 km were analyzed and compared by IRI. The longitudinal profile of the detected road sections was measured using an inertial profiler. The statistical analysis showed that the IRI value prior to road leveling was mainly distributed between 5 and 8 m/km, while the IRI value after road leveling was mainly distributed between 3 and 4.5 m/km. This confirms that the implementation of the Road Smoothing Project has a significant effect on improving road smoothness. Moreover, based on the analysis results, it is recommended that the IRI threshold value for road rehabilitation in Taipei City be set at 4.50 m/km.

Force reduction is one of the most important benefit of applying ultrasonic vibration on milling. However, most of studies so far are limited to experimental investigation. In the current study, an analytical predictive model on cutting forces in ultrasonic vibration-assisted milling is proposed. The three types of tool-workpiece criteria are considered based on the instantaneous position and velocity of tool center. Type I criterion indicates that there is no contact if the instantaneous velocity is opposite to tool rotation direction. Type II criterion checks whether the vibration displacement is larger than the instantaneous uncut chip thickness. Type III criterion considers the overlaps between current and previous tool paths due to vibration. If none of these criteria is satisfied, milling forces are nonzero. Then the calculation is performed by transforming milling and tool geometry configuration to orthogonal cutting at each instant. The orthogonal cutting forces are predicted through the exhaustive search of shear angle and calculation of shear flow stress on tool-chip interface. The axial force is then calculated based on tool geometry, and the milling forces in feed, cutting, and axial directions are calculated after coordinate transformation. The proposed predictive force model in ultrasonic vibration-assisted milling is validated through comparison to experimental measurements on Aluminum alloy 2A12. The predicted values are able to match the measured milling forces with high accuracy of average difference of 13.6% in feed direction and 13.8% in cutting direction.

In laser-assisted milling, higher temperature in shear zone softens the material potentially resulting in a shift of mean residual stress, which significantly affects the damage tolerance and fatigue performance of product. In order to guide the selection of laser and cutting parameters based on the preferred mean residual stress, inverse analysis is conducted by predicting residual stress based on guessed process parameters, which is defined as the forward problem, and applying iterative gradient search to find process parameters for next iteration, which is defined as the inverse problem. An analytical inverse analysis is therefore proposed for the mean residual stress in laser-assisted milling. The forward problem is solved by analytical prediction of mean residual stress after laser-assisted milling. The residual stress profile is predicted through the calculation of thermal stress, by treating laser beam as heat source, and plastic stress by first assuming pure elastic stress in loading process, then obtaining true stress with kinematic hardening followed by the stress relaxation. The variance-based recursive method is applied to solve inverse problem by updating process parameters to match the measured mean residual stress. Three cutting parameters including depth of cut, feed per tooth, and cutting speed, and two laser parameters including laser-tool distance and laser power, are updated with respected to the minimization of resulting residual stress and measurement in each iteration. Experimental measurements are referred on the laser-assisted milling of Ti-6Al-4V grade 5 and ELI. The percentage difference between experiments and predictions is less than 5% for both materials, and the selection is completed within 50 loops.

Use of probiotic lactobacilli has been proposed as a strategy to mitigate damage associated to exposure to toxic metals. Their protective effect against cationic metal ions, such as those of mercury or lead, is believed to stem from their chelating and accumulating potential. However, their retention of anionic toxic metalloids, such as inorganic arsenic, is generally lower. Through the construction of mutants in phosphate transporter genes (pst) in Lactiplantibacillus plantarum and Lacticaseibacillus paracasei strains, coupled with arsenate [As(V)] uptake and toxicity assays, we determined that the incorporation of As(V), which structurally resembles phosphate, is likely facilitated by phosphate transporters. Surprisingly, inactivation in Lc. paracasei of PhoP, the tran-scriptional regulator of the two-component system PhoPR, a signal transducer involved in phosphate sensing, led to an increased resistance to arsenite [As(III)]. In comparison to the wild type, the phoP strain exhibited no differences in the ability to retain As(III), and there were no observed changes in the oxidation of As(III) to the less toxic As(V). These results reinforce the idea that specific transport, and not unspecific cell retention plays a role in As(V) biosorption by lactobacilli, while they reveal an unexpected phenotype for the lack of the pleiotropic regulator PhoP.

Vanadium(IV) chalcogenide materials are of increasing interest for use in catalysis and energy conversion-related applications. Since no ternary compounds are yet known in the V–Se–Te system, we studied ternary VwSeyTe2–y (w = 1.10, 1.13; y = 0.42, 0.72) phases crystallizing in space group P3m1 (no. 164). Two single-crystal specimens with differing compositions of a solid solution were obtained using the ceramic method. All products were characterized by either single-crystal or powder X-ray diffraction. The lattice parameters increase with rising tellurium content in accordance to the larger ionic radius of the tellurium anion compared to selenium. The chemical compositions were confirmed by energy dispersive X-ray spectroscopy. Further, magnetic measurements revealed mostly antiferromagnetic properties. Simultaneous differential scanning calorimetry/thermogravimetric analyses in nitrogen atmosphere showed endothermic decomposition accompanied by the formation of VN. The results of this work can serve as a basis for the synthesis of new phases in the V–Se–Te and related vanadium chalcogenide systems.

A single-crystal of ytterbium-doped “mixed” yttrium-lutetium aluminium garnet with a stoichiometric composition of (Y0.601Lu0.233Yb0.166)3Al5O12 was grown by the Czochralski method and its structure, vibronic, spectroscopic and laser properties were studied. The stimulated-emission cross-section for Yb3+ ions was maximized to 2.53×10-20 cm2 at 1031 nm, the emission bandwidth is ~8 nm and the reabsorption-free luminescence lifetime of the 2F5/2 state is 1.063 ms. Pumped at 941 nm, the Yb-laser generated a maximum output power of 1.04 W at 1.03 and 1.05 μm with a high slope efficiency of 76.4% and a laser threshold of 76 mW. A continuous wavelength tuning over a range of 51.6 nm (1026.4 - 1078.0 nm) was also achieved. Power scaling is achieved using a 969 nm-diode pumped microchip cavity. A maximum output power of ~9 W is obtained at 1.05 μm with a slope efficiency of 76% and with an almost circular laser beam profile.

Compared to tin lead alloys, lead-free tin alloys have lower toxicity, making them more widely used. In this study, Sn-20Bi-0.3Al-xY solders alloys were prepared. The effects of the addition of Y on its microstructure, micro-hardness, wettability and mechanical properties was investigated. The result showed that the addition of Y had significant effect on the refinement of Sn-20Bi-0.3Al-xY. From the spreading tests results, Y increased the wettability of the solders, however when the fraction of Y gradually increased, the wettability reduced. The ultimate tensile and hardness of Sn-20Bi-0.3Al-xY solders alloys were increased as the content of Y increasing.

Enzymes reliant on pyridoxal 5'-phosphate (PLP), the metabolically active form of vitamin B6, hold significant importance in both biology and medicine. They facilitate various biochemical reactions, particularly in amino acid and neurotransmitter metabolisms. Vitamin B6 is absorbed by organisms in its non-phosphorylated form and phosphorylated within cells by pyridoxal kinase (PLK) and pyridox-(am)-ine 5'-phosphate oxidase (PNPOx). The flavin mononucleotide dependent PNPOx enzyme converts pyridoxine 5'-phosphate and pyridoxamine 5'-phosphate into PLP. PNPOx is vital for both biosynthesis and salvage pathways in organisms producing B6 vitamers. However, for those depending on vitamin B6 as nutrient, PNPOx participates only in the salvage pathway. Transferring PLP produced by PNPOx to client apo-enzymes is indispensable for their catalytic function, proper folding and targeting to specific organelles. PNPOx activity deficiencies due to inborn errors lead to severe neurological pathologies, particularly neonatal epileptic encephalopathy. PNPOx enzymes from different organisms maintain PLP homeostasis through highly regulated mechanisms, including structural alterations throughout the catalytic cycle and allosteric PLP binding influencing substrate transformation at the active site. Despite shared features, species-specific regulations are evident among PNPOx enzymes.

We explore an idea put forward many years ago by Zeldovich and Novikov concerning the existence of compact objects endowed with arbitrarily small mass. The energy-density of such objects, which we call “Ghost stars”, is negative in some regions of the fluid distribution, producing a vanishing total mass. Thus, the interior is matched on the boundary surface to Minkowski space-time. Some exact analytical solutions are exhibited and their properties are analyzed. Observational data that could confirm or dismiss the existence of this kind of stellar object, is commented.

A semi–numerical approach proposed many years ago for describing gravitational collapse in the post–quasi–static approximation , , , , is modified in order to avoid the numerical integration of the basic differential equations the approach is based upon. For doing that we have to impose some restrictions on the fluid distribution. More specifically, we shall assume the vanishing complexity factor condition, which allows for analytical integration of the pertinent differential equations and leads to physically interesting models. Instead, we show that neither the homologous nor the quasi–homologous evolution are acceptable since they lead to geodesic fluids, which are unsuitable for being described in the post–quasi–static approximation. Also, we prove that, within this approximation, adiabatic evolution also leads to geodesic fluids and therefore we shall consider exclusively dissipative systems. Besides the vanishing complexity factor condition, additional information is required for a full description of models. We shall propose different strategies for obtaining such an information, which are based on observables quantities (e.g. luminosity and redshift), and/or heuristic mathematical ansatz. To illustrate the method, we present two models. One model is inspired in the well known Schwarzschild interior solution, and another one is inspired in Tolman VI solution.

We present a series of computer-assisted high resolution transmission electron (HRTEM) simulations to determine Moiré patters by induced twisting effects between slabs at rotational angles of 3°, 5°, 8°, and 16°, for molybdenum disulfide, graphene, tungsten disulfide, and tungsten selenide layered materials. In order to investigate the electronic structure, a series of numerical simulations using DFT methods was completed using CASTEP with a generalized gradient approximation to determine both band structure and density of states on honeycomb like new superlattices. Our results indicate metallic transitions when rotation approaches 8° with respect to each other for most of the two-dimensional systems that were analyzed.

Precipitation type is a key parameter used for better retrieval of precipitation characteristics as well as to understand the cloud-convection-precipitation coupling processes. Ice crystals and water droplets inherently exhibit different characteristics in different precipitation regimes (e.g., convection, stratiform), which reflect on satellite remote sensing measurements that help us distinguish them. The Global Precipitation Measurement (GPM) Core Observatory’s Microwave Imager (GMI) and Dual-Frequency Precipitation Radar (DPR) together provide ample information on global precipitation characteristics. As an active sensor, DPR provides an accurate precipitation type assignment, while passive sensors like GMI are traditionally only used for empirical understanding of precipitation regimes. Using collocated precipitation type flags from DPR as the “truth”, this paper employs machine learning (ML) models to train and test the predictability and accuracy of using passive GMI-only observations together with ancillary information from reanalysis and GMI surface emissivity retrieval products. Out of six ML models, four simple ones (Support Vector Machine, Neural Network, Random Forest, and Gradient Boosting) and the 1-D convolutional neural network (CNN) model are identified to produce 90% - 94% prediction accuracy globally for 5 types of precipitation (convective, stratiform, mixture, no precipitation, and other precipitation), which is much more robust than previous similar effort. One novelty of this work is to introduce data augmentation (subsampling and bootstrapping) to handle extremely unbalanced samples in each category. Careful evaluation of Impact matrices demonstrate that polarization difference (PD) and surface emissivity at high-frequency channels dominate the decision process, which are consistent with the physical understanding of polarized microwave radiative transfer over different surface types, as well as in snow and liquid clouds with different microphysical properties. Furthermore, the view-angle dependency artifact that DPR precipitation flag bears with does not propagate into the conical-viewing GMI retrievals. This work provides a new and promising way for future physics-based ML retrieval algorithm development.

We present a modified version of the Szilard Engine, demonstrating that an explicit measurement procedure is entirely unnecessary for its operation. By considering our modified engine, we are able to provide a new interpretation of Landauer’s original argument for the cost of erasure. From this view, we demonstrate that a reset operation is strictly impossible in a dynamical system with only conservative forces. Then, we prove that to approach a reset yields an unavoidable instability at the reset point. Finally, we present an original proof of Landauer’s principle that is completely independent from the Second Law of Thermodynamics.

Introduction: Research studies have shown that workplace stress and physical immobility can have a multi-layered effect on the human body. It causes degrade our physical functioning, and also having negative effect on our performance. Yoga techniques have proved to be effective at various levels, including physical, mental, and emotional health. Objective: This study aimed to determine the efficacy of a short-term Yoga protocol – Y break, for improved well-being and resilience to stress. It is intended to working population at work to de-stress, refresh, and refocus. Methods: This study was conducted as a single-arm, multi-centric, experimental pilot trial. Prominent yoga institutes in six metropolitan cities were engaged in this study. Participants practised specific yoga techniques for 5 minutes, twice a day, for 15 days. Pre & post-intervention data was collected along with feedback about the protocol. A self-report questionnaire, based on the Pancha kosha parameters, was used to record pre- and post-data. Results: The Statistical data analysis shown significant improvement in every parameter selected for the study. Conclusion: A five-minute yoga break can do wonders for the health-related parameters of the working population; therefore, it should be introduced in all organizations to improve the quality of life and work.

Zeolite Y with microporous and hierarchical structure containing Ti–Ni and Ti–Co oxides were obtained as active photocatalysts. Different Ti amounts (5, 10% TiO2) were supported, followed by loading of Ni or Co oxides (5 %). The X-ray diffraction evidenced the presence of TiO2 as anatase. N2 adsorption-desorption results showed type IV isotherms, for hierarchical zeolite Y samples, and a combination of type IV and I isotherms, for zeolite Y samples. UV–Vis diffuse reflectance spectra showed shift of absorption band to visible with increasing of Ti loading and especially after Co and Ni addition. A significant effect of the support was evidenced for Ti and interaction with Co/Ni species. The zeolite Y support stabilizes Ti in the 4+ oxidation state while hierarchical zeolite Y support favored the formation of Ti 3+ species and oxidation of Co and especially of Ni to 3+. Photocatalytic activity, under UV and visible light, was evaluated in degradation of amoxicillin, used as a model test. The photocatalytic mechanism was investigated using ethanol, p-benzoquinone and KI as ·OH, ·O2- radicals and hole (h+) scavengers. The best results were obtained for the immobilized Ni-Ti species on hierarchical zeolite Y support.

INTRODUCTION: Achalasia is a pathology with an incidence of 1 in 100,000 inhabitants per year. There are very limited data on achalasia in the obese population, especially in those undergoing bariatric surgery. The approach of choice for cases of achalasia is fundoplication to correct the reflux; however, lacking a fundus due to a previous gastrectomy, an alternative that offers optimal results should be chosen. Here we present the surgical approach in a case of esophageal achalasia and a history of vertical sleeve gastrectomy, where we performed simultaneous Heller's cardiomyotomy and laparoscopic Roux-en-Y gastric bypass, as well as the results obtained. CASE PRESENTATION: 44-year-old woman with no chronic degenerative diseases, with a previous record of vertical sleeve gastrectomy 5 years ago, who started 1 year and 5 months earlier with dysphagia to liquids, then to solids, in addition to weight loss of 10 kilograms in 4 months. The BMI before vertical sleeve gastrectomy was 32 kg/m2, her BMI at the time of admission was 20 kg/m2; she also presented regurgitation and generalized weakness. After analyzing the surgical options, it was decided to perform a Heller cardiomyotomy and a Roux-en-Y gastric bypass. DISCUSSION AND CONCLUSIONS: The procedure turned out to be safe and successful in treating achalasia symptomatology, in addition to complete resolution of the reflux symptom.

In this paper, we have constructed a WKB approximation for graphene having a Y-shaped Kekul\'e lattice distortion and a special folding of the $\mbox{\boldmath$K$}$ and $\mbox{\boldmath$K$}^\prime$ valleys, which leads to very specific linear energy dispersions with two non-equivalent pairs of subbands. These obtained semi-classical results, which include the action, electron momentum and wave functions, are utilized to analyze the dynamics of electron tunneling through non-square potential barriers. In particular, we explore resonant scattering of an electron by a potential barrier built on Kekul\'e-distorted graphene. Mathematically, a group of consecutive equations for a semi-classical action have been solved by following a perturbation approach under the condition of small strain-induced coupling parameter $\Delta_0 \ll 1$ (a good fit to its actual value $\Delta_0 \backsim 0.1$). Specifically, we consider a generalized model for Kek-Y graphene with two arbitrary Fermi velocities. The dependence of the electron transmission amplitude on the potential profile $V(x)$ and band parameters of Kekul\'e-patterned graphene has been explored and analyzed in details.

Observations collected during cold season precipitation periods at Utquagvik, Alaska and at the mul-tidisciplinary drifting observatory for study of Arctic climate (MOSAiC) are used to statistically ana-lyze relations among the atmospheric water cycle parameters including the columnar supercooled liq-uid and ice amounts (expressed as liquid water and ice water paths, i.e., LWP and IWP), the integrated water vapor (IWV) and the near-surface snowfall rate. Data come from radar and radiometer-based retrievals and from optical precipitation sensors. While correlation between snowfall rate and LWP is rather weak, correlations coefficients between radar-derived snowfall rate and IWP are high (~ 0.8), which is explained, in part, by generally low LWP/IWP ratios during significant precipitation. Corre-lation coefficients between snowfall rate and IWV are moderate (~0.45). Correlations are generally weaker if snowfall is estimated by optical sensors, which is, in part, due to blowing snow. Correlation coefficients between near-surface temperature and snowfall rates are low (r<0.3). Results from the Alaska and MOSAiC sites are generally similar. These results are not very sensitive to the amount of time averaging (e.g., 15-minute averaging versus daily averages). Observationally-based relations among the water cycle parameters are informative about atmospheric moisture conversion processes and can be used for model evaluations.

Hydrogels have gained significant attention as vehicles for transdermal delivery systems. These polymeric-structured substances have been implemented in pharmaceutical and cosmetic applications. Many factors are employed in their preparation. Light, pH, temperature and specific molecules ligands are commonly used in the production of hydrogels. The Transdermal delivery system (TDD) is a widely used route, used to deliver actives/drugs via the skin. Hydrogels as a TDD have been shown to be efficient in enhancing the efficacy in delivering the actives and drugs. The aim of this review is to discuss the hydrogels application in both dermatological therapeutic and cosmetic applications, covering the types, and properties of hydrogel polymer networks. Furthermore, this review presents one of the most extensively used polymers (Hyaluronic acid HA) in this field and discusses the properties, preparation methods and applications of HA hydrogel patches as a delivery system, including methods of loading the actives and the releasing of these actives from them.

The changes in the properties of three biological events, that occur with cerebral aging, are discussed. These adverse changes already begin to develop early in mid-life and gradually become more pronounced with senescence. Essentially, they are reflections of the progressive decline in effectiveness of key processes, resulting in the deviation of essential biochemical trajectories to ineffective and ultimately harmful variants of these programs. The emphasis of this review is the major role played by mitochondria in such transition of these three important processes toward more deleterious variants as brain aging proceeds. 1. The immune system. The shift away from an efficient immune response to a more unfocused, continuing inflammatory condition. Such a state is both ineffective and harmful. 2. Reactive oxygen species are important intracellular signaling systems. Also, microglial phagocytic activity utilizing short lived reactive oxygen species contribute to the removal of aberrant or dead cells and bacteria. These processes are transformed into an excessive, untargeted and persistent generation of pro-oxidant free radicals (oxidative stress). 3. The normal efficient neural transmission is modified to a state of undirected, chronic low-level excitatory activity. Each of these changes is characterized by the occurrence of continuous activity that is inefficient and diffuse. The signal/noise ratio of several critical biological events is thus reduced as beneficial responses are gradually replaced by their impaired and deleterious variants.

School-aged children may benefit from education interventions focused on healthy eating and physical activity to improve their quality of life. This article aims to review scientific evidence on food and nutrition education (FNE) in Spanish-speaking countries for the prevention of overweight and obesity in school-aged children (6-12 y). Articles were searched between April and August 2021. The searches were conducted using MEDLINE, Google Scholar, and SciELO. The primary search for articles focused on the experience of FNE interventions in Spanish-speaking countries. Overall, 518 articles were found and 33 studies were eligible for data extraction. Forty-two percent of the studies had a focus on FNE and 64% were focused on describing the eating habits of schoolchildren. Nutritional assessments (anthropometric) were found frequently with 91% and 30% of the studies focused on physical activity. All interventions focused on preventing or reducing overweight and obesity in school-age children. Educational, cognitive, dietary, and physical activity practices were described, whit being educational the most frequent intervention. Interventions reported positive effects of FNE interventions to improve knowledge and practices of healthy lifestyles in school-age children.

An accumulating body of evidence suggests that physiological reactive oxygen species (ROS) generated by NADPH oxidases act as a redox signal to re-establish homeostasis, a capacity that progressively declines during aging, but is maintained in long-lived animals to promote healthy aging. In the model organism Caenorhabditis elegans, ROS generated by dual oxidases (Duox) are important for extracellular matrix integrity, pathogen defense, oxidative stress resistance, and longevity. The Duox enzymatic activity is tightly regulated and under cellular control. Developmental molting cycles, pathogen infections, toxins, mitochondrial-derived ROS, drugs, and small GTPases (RHO-1) can activate Duox (BLI-3) to generate ROS, whereas NADPH oxidase inhibitors and negative regulators, such as MEMO-1, can inhibit Duox to generate ROS. Three mechanisms-of-action have been discovered for the Duox/BLI-3-generated ROS: 1) enzymatic activity to catalyze cross-linking of free tyrosine ethyl ester in collagen bundles to stabilize extracellular matrices, 2) high ROS bursts/levels to kill pathogens, and 3) Redox signaling activating downstream kinase cascades to transcription factors orchestrating oxidative stress- and immunity responses to re-establish homeostasis. Although Duox function at the cell surface is well established, recent genetic and biochemical data also suggests a novel role for Duoxs at the endoplasmic reticulum membrane to control redox signaling. Evidence underlying these mechanisms initiated by ROS from NADPH oxidases and their relevance for human aging are discussed in this review. Appropriately controlling NADPH oxidase activity for local and physiological redox signaling to maintain cellular homeostasis might be a therapeutic strategy to promote healthy aging.

After the global challenges posed by COVID-19, researchers strived to identify risk factors for severe cases, which lead to various complications - including death. Lifestyle modifications, such as implementing a healthy diet and recommended physical activity, have shown to be protective against severe COVID-19 cases. Despite an association of a plant-based diet with reduced COVID-19 severity, specific dietary characteristics have not been identified. Also, the methodology for measuring physical activity is variable, with studies overlooking the intensity or the habit components of physical activity. To bridge this gap, our study designed, validated, and applied a retrospective questionnaire with aims of exploring the relationship between lifestyle factors, specifically diet and physical activity, and severe COVID-19. We considered the intensity and years of physical activity habit, which is a limitation of other questionnaires. Results reveal associations of age and BMI with severe COVID-19. An excessive sugar diet was found to be associated with severe COVID-19 and increased symptom duration. We also observed an inverse relationship pattern of moderate and vigorous intensity physical activity across case severity, which is absent in walking PA. This study lays a foundation for research aiming to identify lifestyle factors that prevent severe COVID-19 cases.

Real-time multi-axis distributed tactile sensing is a critical capability if robots are to perform stable gripping and dexterous manipulation, as it provides crucial information about the sensor-object interface. In this paper, we present an optical-based 6-axis tactile sensor designed in a fingertip shape for robotic dexterous manipulation. The distributed sensor can precisely estimate local XYZ force and displacement at ten distinct locations, and provide global XYZ force and torque measurements. Its compact size, comparable to that of a human thumb, and minimal thickness allow seamless integration onto existing robotic fingers, eliminating the need for complex modifications to the gripper. The proposed sensor design uses a simple, low-cost fabrication method. Moreover, the optical transduction approach uses light angle and intensity sensing to infer force and displacement from deformations of individual sensing units that form the overall sensor, providing distributed 6-axis sensing. The local force precision at each sensing unit in the X, Y, and Z axes is 20.89 mN, 19.19 mN, and 43.22 mN, respectively, over an local force range of approximately ±1.5 N in X and Y and 0 to -2 N in Z. The local displacement precision in the X, Y and Z axes is 56.70 μm, 50.18 μm and 13.83 μm, respectively, over a local displacement range of ±2 mm in the XY directions and 0 to -1.5mm in Z (i.e., compression). Additionally, the sensor can measure global torques, Tx, Ty and Tz, with a precision of of 1.90 N-mm, 1.54 N-mm and 1.26 N-mm, respectively. The fabricated design is showcased by integrating it with an OnRobot RG2 gripper and illustrating real-time measurements during in simple demonstration task which generate changing global forces and torques.

Recently, there have been revolutions in the development of both gene therapy and genome surgical treatments for inherited diseases. Much of this progress has been centered around hereditary retinal dystrophies, because the eye is an immune-privileged and anatomically ideal target. Gene therapy treatments, already demonstrated to be safe and efficacious in numerous clinical trials, are benefitting from the development of new viral vectors, such as dual and triple AAVs. CRISPR/Ca9, which revolutionized the field of gene editing, is being adapted into more precise “high fidelity” and catalytically dead variants. New CRISPR endonucleases, such as CjCas9 and Cas12a, are generating excitement in the field as well. Stem cell therapy has emerged as a promising alternative, allowing human embryo derived stem cells and induced pluripotent stem cells to be edited precisely in vitro and then reintroduced into the body. This article highlights recent progress made in gene therapy and genome surgery for retinal disorders, and it provides an update on precision medicine FDA treatment trials.

Cellular senescence has recently been recognized as a hallmark of cancer, reflecting its association with aging and inflammation, its role as a response to deregulated proliferation and oncogenic stress, and its induction by cancer therapies such as radiation, chemotherapy, and targeted agents. While such therapy-induced senescence (TIS) has been linked to resistance, recurrence, metastasis and normal tissue toxicity, TIS has the potential to enhance therapy response and stimulate anti-tumor immunity. In this review, we examine the Jekyll and Hyde nature of senescent cells (SnCs), with a particular focus on how their persistence while expressing the senescence-associated secretory phenotype (SASP) modulates the tumor microenvironment through autocrine and paracrine mechanisms. Via the SASP, the formation of SnCs may alternately mediate resistance or response to conventional therapy. Further, toward fulfilling the unmet potential of cancer immunotherapy, we consider how SnCs may influence tumor inflammation and serve as a source of antigen to potentiate anti-tumor immunity. This new view suggests treatment strategies based on inducing TIS to enhance immune checkpoint blockade. Finally, we describe strategies for mitigating the detrimental effects of senescence, such as modulating the SASP or targeting SnC persistence, toward enhancing the benefits of cancer treatment.

Abstract: Herbicide flashback is an undesirable response that results in damage or mortality of non-target plants near chemically treated plants. In severe instances, crop trees can be injured resulting in financial loss or inability to capture management objectives. Land managers need to know the potential limitations of using triclopyr acid (50% solution in water) and what quantity can cause damage to non-target trees (trees not aimed to control via herbicide). Three naturally regenerated (previous clearcut) bottomland hardwood sites, ranging from 14–20 years of age, received partial overstory deadening using Trycera® herbicide. Residual “leave” trees experienced indirect herbicide uptake resulting in some trees either experiencing mortality or partial mortality with top die-back/epicormic branching. An increased probability of damage occurred as tree diameter decreased and the number of treated stems around non-target stems increased. American sycamore, green ash, and sweetgum were most susceptible to flashback. This study examines the unanticipated chemical effect of deadening adjacent stems surrounding residual leave trees in poorly drained soils.

The efficient recognition and classification of personal protective equipment are essential for en-suring the safety of personnel in complex industrial settings. Using the existing methods, manually performing macro-level classification and identification of personnel in intricate spheres is tedious, time-consuming, and inefficient. The availability of several artificial intelligence models in recent times presents a new paradigm shift in object classification and tracking in complex settings. In this study, several compact and efficient deep learning model architectures are explored, and a new efficient model is constructed by fusing the learning capabilities of the individual, efficient models for better object feature learning and optimal inferencing. The new model construct follows the contributory learning theory whereby each fussed model brings its learned features, which are then combined to obtain a more accurate and rapid model using normalized quantization-aware learning. During the investigation, a separable convolutional driven model was constructed as a base model, and then the various efficient architectures combined for the rapid identification and classification of the various hardhat classes used in complex industrial settings. A remarkable rapid classification and accuracy were recorded with the new resultant model.

Accurate pose estimation is a fundamental ability that all mobile robots must posses in order to navigate a given environment. Much like a human, this ability is dependent on the robot's understanding of a given scene. For Autonomous Vehicles (AV's), detailed 3D maps created beforehand are widely used to augment the perceptive abilities and estimate pose based on current sensor measurements. This approach however is less suited for rural communities that are sparsely connected and cover large areas. Topological maps such as OpenStreetMaps have proven to be a useful alternative in these situations. However, vehicle localization using these maps is non-trivial, particularly for the global localization task, where the map spans large areas. To deal with this challenge, we propose road descriptors along with an initialization technique for localization that allows for fast global pose estimation. We test our algorithms on (real world) maps and benchmark them against other map based localization as well as SLAM algorithms. Our results show that the proposed method can narrow down the pose to within 50 centimeters of the ground truth significantly faster than the state of the art methods.

We assessed how close human perceptions of landscape modification matched a multivariate index based on remotely sensed data of the same locations. Using a Human Footprint (HF) map of the continental U.S. (scaled 0-100), we created three series of aerial images, each with ten images distributed evenly across the 10 deciles of HF score. Using a web-based survey, 290 members of the global public ranked the images in one series based on their perception of the degree of human modification. Respondents also reported age, sex, and country. The degree of correspondence between rankings by respondents and by HF score was high, an average of 1.29 units of difference out of a maximum possible of 5.0. Differences among respondents were not explained by age, sex, or general geographic location. These results suggest that human perception of relative landscape modification conforms closely with the relative ranking made by a multivariate, analytical index.

We firstly discuss classical stability for a dynamical system of two ions levitated in a 3D Radio-Frequency (RF) trap, assimilated with two coupled oscillators. We obtain the solutions of the coupled system of equations that characterizes the associated dynamics. In addition, we supply the modes of oscillation and demonstrate the weak coupling condition is inappropriate in practice, while for collective modes of motion (and strong coupling) only a peak of the mass can be detected. Phase portraits and power spectra are employed to illustrate how the trajectory executes quasiperiodic motion on the surface of torus, namely a Kolmogorov-Arnold-Moser (KAM) torus. In an attempt to better describe dynamical stability of the system, we introduce a model that characterizes dynamical stability and the critical points based on the Hessian matrix approach. The model is then applied to investigate quantum dynamics for many-body systems consisting of identical ions, levitated in 2D and 3D ion traps. Finally, the same model is applied to the case of a combined 3D Quadrupole Ion Trap (QIT) with axial symmetry, for which we obtain the associated Hamilton function. The ion distribution can be described by means of numerical modeling, based on the Hamilton function we assign to the system. The approach we introduce is effective to infer the parameters of distinct types of traps by applying a unitary and coherent method, and especially for identifying equilibrium configurations, of large interest for ion crystals or quantum logic.

This year marks the 20th anniversary of the discovery that proteins with various cellular functions can be temporarily immobilized in the nucleolus, a process known as nucleolar sequestration. This review reflects on the progress made to understand the physiological roles of nucleolar sequestration and the mechanisms involved in protein immobilization. We discuss how nucleolar sequestration consists of a highly choreographed amyloidogenic liquid-to-solid phase transition that converts the nucleolus into Amyloid bodies (A-bodies). The study of solid condensates A-bodies will offer unique perspectives on cellular assembly of membrane-less compartments and provide alternative insights on pathological amyloidogenesis involved in neurological disorders.