Aim at a better understanding of the flow field around a fully appended Joubert BB2 submarine model and complementing the experimental investigations of the wake of the hydroplanes and sail, the Large eddy simulation (LES) with the dynamic Smagorinsky model is conducted. Three sets of grids with a maximum grid number of up to 228 million are designed, to perform the LES simulation for the Joubert BB2 at 10° yaw conditions, with a freestream Reynolds (Re) number based on the local freestream velocity and the hull length of ReL=2.2×107. And comparison of the wake of the cruciform appendage is made with experiments, to verify the computational accuracy and examine the influence of the spatial resolution. A satisfactory result shows more favorable agreement with experimental measurements as the improvement of spatial resolution, with the relative error of the vortice centers well within 7.2% in the most refined grid arrangement. And under this grid arrangement, the evolution characteristics of three co-rotating vortices originating from the cruciform appendage are further described in detail at straight ahead and 10° yaw conditions.

The roots, leaves, and other parts of American ginseng contain ginsenosides and polyphenols, among other bioactive components. So far, reports on exploring the changes in bioactive components within its leaves after heat treatment have been limited. In the present study, we investigated the effects of far-infrared irradiation (FIR) heat treatment from 160 to 200 ℃ on the deglycosylation and dehydration rates of the bioactive components in American ginseng leaves. As the temperature was increased, the amounts of constant ginsenosides decreased while those of rare ginsenosides increased. After FIR heat treatment of the American ginseng leaves at an optimal 190 ℃, the highest total polyphenolic content and kaempferol content were detected, the antioxidant activity was significantly enhanced, and the amounts of rare ginsenosides F4, Rg6, Rh4, Rk3, Rk1, Rg3, and Rg5 were 41, 5, 37, 64, 222, 17, and 266 times higher than those in the untreated leaves, respectively. Moreover, the radical scavenging rates for 2,2-diphenyl-1-picrylhydrazyl and 2,2'-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid), and the reducing power of the treated leaf extract, were 2.17, 1.86, and 1.77 times higher, respectively. Hence, optimal FIR heat treatment at 190 ℃ is an efficient method for producing beneficial bioactive components from American ginseng leaves.

Forest ecosystems make a greater contribution to carbon (C) stocks than any other terrestrial ecosystem. To understand the role of regional forest ecosystems in global climate change and carbon exchange, forest C stock and its spatial distribution within the small (2,300 km2) Liuxihe River basin were analyzed to determine the different contributors to the C stock. Forest C stocks were quantified by measuring the biomass of trees, understory vegetation, litter and roots, as well as soil organic C, using data from field samples and laboratory experiments. The results showed that forests stored 38.04 Tg C in the entire basin, with secondary and planted forests accounting for 89.82% and 10.18%, respectively, of the stored C. Five types of forests, a subtropical evergreen broad-leaved forest, a subtropical coniferous and broad-leaved mixed forest, a subtropical coniferous forest, a timber forest, and a non-wood forest, stored 257.55 ± 15.01, 218.92 ± 9.59, 195.24 ± 18.29, 177.42 ± 17.55, and 117.86 ± 6.04 Mg C ha−1, respectively. In the forest ecosystem C stocks of the basin, soils averagely contribute about 73.78%, not including root underground biomass. It provides a comprehensive method for forest ecosystem carbon investigation and forest management in small basin scale.

Lake sediment records are of great importance for understanding the evolution of watershed environments. Various studies have been carried out to constrain the depositional ages of lake sediments and examine their physical, chemical, and biological characteristics, aiming to construct historical vegetation, environment and climate patterns in Chinese lake watersheds. In this study, we obtained relevant literature on lake sediment records by searching the key word 'age-depth' from the databases – Web of Science and China National Knowledge Infrastructure (CNKI, the largest Chinese academic database). We analyzed the literature based on its type (published in a Chinese/English journal or as a Master’s/PhD thesis), period of publication, journal (if published in a journal), key authors, study area, dating scale, and main aims. The results suggest that the lakes in the plateau regions are the most popular research topic typically covering 100–200 years (short-term) and 500–30,000 years (long-term). The literature focuses on a wide range of topics, from past environmental evolution in the watershed to lake ecology, and provides a solid foundation for better understanding regional climate change and the preservation of lake environments and ecosystems. In the future, resulting data from environmental reconstruction with lake sediments will be needed to integrate with emerging information processing technologies (e.g., artificial intelligence and meta-analysis), to disentangle the complex interplay between Earth surface processes and global climate change; furthermore, strengthening interdisciplinary collaboration will deepen our comprehension of man-land relationship and promote the sustainable management of lake ecosystems in the context of global climate change.

Alginate extraction is from seaweed, and lignin separation is from by-product corn (stalks and leaves). Alginate/lignin is a synthetic polymer rich in biological activity of great interest. Antioxidant activities of alginate/lignin were evaluated, such as total antioxidant activity, reducing power activity, DPPH free radical scavenging activity, and α – glucosidase inhibition activity. The test of anticancer activity was on four cell lines (Hep G2, fibroblast, MCF-7, and NCI H460). Determination of physical-chemistry characteristics of alginate/lignin was through FTIR, DSC, SEM_EDS, SEM_EDS mapping, XRD, XRF, and 1H-NMR. A study of acute toxicity of alginate/lignin was on Swiss albino mice. The results showed alginate/lignin possessed antioxidant activity such as total antioxidant activity, reducing power activity, especially, α – glucosidase inhibition activity, and no free radical scavenging activity. Alginate/lignin did not be typical in cancer cell lines. Alginate/lignin existed in a thermally stable regular spherical shape in the investigated thermal region. Some specific functional groups of alginate and lignin did not exist in alginate/lignin crystal. Elements such as C, O, Na, and S were popular in the alginate/lignin structure. LD0 and LD100 of alginate/lignin in mice were 3.91 g/kg and 9.77 g/kg, respectively. Alginate/lignin is the potential for application as pharmaceutical materials, functional foods, and supporting diabetes treatment.

Technological advancements must keep pace with earth’s rising demand for energy, while minimizing the carbon footprint on earth. One such option is using space based solar (SBS) radio frequency (RF) microwave power beaming. This innovative and novel technology is currently being explored to address terrestrial photovoltaic (PV) intermittency and provide a method to transmit power to other spacecraft in various orbits. This modality of power generation and distribution presents a new way to power terrestrial off-grid applications and earth orbiting spacecraft. In 1968, Dr. Peter Glaser published "Power from the Sun: Its Future", which serves as the foundation of this paper to revitalize scientific interest and efforts in this topic. This paper will primarily focus on the reliance of SBS initiatives on reusable launch vehicles (RLV) to place SBS spacecraft in a designated orbit, as well as the technological, economic, and operational challenges associated with power beaming to earth and other spacecraft. This includes a discussion of the variables from the operational environment that contribute or accelerate spacecraft end of life.

Extracts of Cordyceps militaris which possess the bioactive capacity such as antimicrobial activity and DPPH-free radical scavenging capacity, are applied to the serum product. This finished serum product has been evaluated the in vitro bioactivity and the stability with expect to find out a good extract with a suitable percentage used for serum product as natural materials on preservatives and antioxidation.

Changing climate conditions and rapidly increasing carbon dioxide emissions have severely affected the global ecosystem and world economy. Governments around the world have paid attention to these resulting challenges and enacted many policies to reduce environmental pollution and carbon dioxide (CO2) emissions. This study aimed to determine and understand the relationship between innovation, foreign direct investment, economic growth, renewable consumption and CO2 emission in Vietnam. Information was collected annually based on the annual data of the General Statistics Office of Vietnam and World Bank from 2000 to 2022. Data processing was conducted using the STATA 17.0 software. The innovation affects Vietnam’s environmental pollution. Innovation positively affect environmental pollution in Vietnam; if Vietnam’s innovation were to increase by 1%, CO2 emissions would increase by 0.68%. The empirical research results of this study also show that renewable energy consumption has a negative effect on environmental pollution in Vietnam; if renewable energy were consumed at a 1% increase, CO2 emission would decrease by 0.51%. In addition, FDI inflows and economic growth have strongly positive affecting to environmental pollution; if Vietnam’s FDI inflows were to increase 1%, CO2 emissions would increase 1.39%; if Vietnam’s GDP increase 1% then CO2 emission would increase 1.26%. This paper also provides some recommendations that can assist Vietnam in developing a green and sustainable economy in the technology revolution 4.0 to achieve the United Nations Sustainable Development Goals (SDGs) over a long-term period.

Smart City has emerged as the mainstream paradigm for urban governance innovation, sustainable development, and strategy upgrades, which is drawing attention from scholars worldwide. However, current frameworks for Smart City assessment remain incomplete and simplistic. In is paper, 30 national or provincial capitals in China were selected and we designed a tri-dimensional SPI model—Social, Physical, and Information Space—for smart city spatial development assessment. Utilizing methods such as entropy weighting, coupled coordination degree models, and the Dagum Gini coefficient, this study assesses the spatial development and coupled coordination of 30 cities from 2011 to 2019. Finally, by means of BP neural networks, the study examines the contribution of each indicator to the spatial coupled coordination. The results indicated that with a narrowing disparity in development speeds among different regions, the spatial coupled coordination development level of smart capitals in China has steadily increased, presenting a pattern of staggered distribution. Moreover, the IS subsystem plays the most significant role in coupled coordination. The significance of this research lies in its tri-dimensional spatial perspective of the spatial development and coupled coordination differences of the Smart City, providing evidence-based support for the regional layout and optimization in China.

Three Dimensional Variational data assimilation or analysis (3DVAR) is one of most classical methods for providing the initial values for numerical models. In this method, the dimensions of the background error covariance and the observational error covariance matrices are large. Therefore, it is difficult to get the inverse of the covariance matrices and to reduce the orders of these matrices without information loss. With the use of the Sylvester Equation, on the basis of a new linear regression, a new cost function for 3DVAR was given. For the first-guess m×n field, there is an approximate 1−(m²+n²)/(mn×mn) reduction with m>1 & n>1 by using the cost function. The results of the numerical experiments show that the effect of this algorithm is no worse than that of the old cost function for 3DVAR.

In nonlinear self-consistent system, Lorenz system (Lorenz equations) is a classic case with chaos solutions which are sensitively dependent on the initial conditions. As it is difficult to get the analytical solution, the numerical methods and qualitative analytical methods are widely used in many studies. In these papers, Runge-Kutta method is the one most often used to solve these differential equations. However, this method is still a method based on explicit time scheme, which would be the main reason for the chaotic solutions to Lorenz system. In this work, numerical experiments based on implicit time scheme and explicit scheme are setup for comparison, the results show that: in implicit time scheme, the numerical solutions (counterexamples) are without chaos; for an original volume, the volume shrinks exponentially fast to 0 in common.

Utilizing unmanned aerial vehicles (UAVs) to facilitate wireless communication has emerged as a viable and promising strategy aimed at enhancing both current and prospective wireless systems. This approach offers many advantages by establishing line-of-sight connections, optimizing operational efficiency, and enabling flexible deployment capabilities in various terrains. Thus, in this paper, we investigate UAV communication in a relaying network in which a UAV helps communication between a source and two destination users while flying to a location. To have a complete view of our proposed system, we consider both orthogonal multiple access as OFDM and non-orthogonal multiple access (NOMA) scenarios. Moreover, we apply successive convex optimization (SCO) and the Block-coordinate gradient descent (BCGD) for the sum-rate optimization problems to improve the system performance under constraints of total bandwidth and total power at the ground base station and UAV. The experimental results validate that the achievable secrecy rates are notably enhanced by using our proposed algorithms and show optimal trends for critical parameters, such as transmit powers, the flight trajectory and speed of UAV, and resource allocation of OFDM and NOMA.

The global warming our generation is experiencing is just one of the great environmental crises of the Anthropocene, a geological period that began with the use of fossil fuels and that, in merely one century and a few decades of industrial activity, has altered ecosystemic processes that sustain human health and well-being. Beyond the loss of the “intrinsic value of nature”, changes in the magnitude and direction of biogeochemical cycles and increases in temperature are phenomena that not only accompany the loss of habitats and species but impair resilience by ultimately generating greater and more complex numbers and types of exposures that constitute a danger to human health. In this study, we attempted to offer some notes about the margin, understood as that space with the greatest inequity and therefore the fastest growth of risk: the collision area where deprivation marks the social determinants of health and where the greatest interaction with causes of disease occur.

Studying the two famous old problems that why the moon can move around the Sun and why the orbit of the Moon around the Earth cannot be broken off by the Sun under the condition that calculating with F=GMm/R^2, the attractive force of the Sun on the Moon is almost 2.2 times that of the Earth. We found that the planet and moon are unified as one single gravitational unit which results in that the Sun cannot have the force of F=GMm/R^2 on the moon. The moon is moved by the gravitational unit orbiting around the Sun. It could indicate that the gravitational field of the moon is limited inside the unit and the gravitational fields of both the planet and moon is unified as one single field interacting with the Sun. The findings are further clarified by reestablishing Newton’s repulsive gravity.

Viruses can induce the fusion of infected and neighboring cells, leading to the formation of syncytia. Cell-cell fusion is mediated by viral fusion proteins on the plasma membrane of infected cells that interact with cellular receptors on neighboring cells. Viruses use this mechanism to spread rapidly to adjacent cells or escape host immunity. For some viruses, syncytium formation is a hallmark of infection and a known pathogenicity factor. For others, the role of syncytium formation in viral dissemination and pathogenicity remains poorly understood. Human cytomegalovirus (HCMV) is an important cause of morbidity and mortality in transplant patients and the leading cause of congenital infections. Clinical HCMV isolates have broad cell tropism but differ in their ability to induce cell-cell fusions, and little is known about the molecular determinants. We developed a system to analyze HCMV glycoprotein B (gB) variants in a defined genetic background. HCMV strains TB40/E and TR were used as vectors to compare the fusogenicity of six gB variants from congenitally infected fetuses with those from three laboratory strains. Five of them conferred the ability to induce fusion of MRC-5 human embryonic lung fibroblasts to one or both backbone strains, as determined by a split GFP-luciferase reporter system. The same gB variants were not sufficient to induce syncytia in infected ARPE-19 epithelial cells, suggesting that additional factors are involved. The system described here allows a systematic comparison of the fusogenicity of viral envelope glycoproteins and may help to clarify whether fusion-promoting variants are associated with increased pathogenicity.

Climate change related increases in frequency and intensity of heatwaves affect viticulture, leading to losses in yield and grape quality. We assessed whether canopy architecture manipulation mitigates the effects of summer stress in a Mediterranean vineyard. Muscat of Alexandria grapevines were monitored during 2019-2020. Two canopy shoot positioning treatments were applied: Vertical shoot positioning (VSP); and Modulated shoot positioning (MSP), the west side upper foliage released to promote partial shoot leaning, shading the clusters. Clusters were sampled at pea size (PS), veraison (VER) and full maturation (FM). Measurements included rachis anatomy and hydraulic conductance, and aquaporins (AQP) and stress-related genes expression in cluster tissues. Results show significant seasonal and interannual differences in Kh and vascular anatomy. At VER, Krachis , Krachis+pedicels, and xylem diameter decreased but were unaffected by treatments. The Phloem/Xylem ratio was either increased (2019) or reduced (2020) in MSP, compared to VSP. Most AQP were down-regulated at FM in pedicels, and up-regulated at VER in pulp. A potential maturation shift in MSP was observed, confirmed by the up-regulation of several stress-related genes in all tissues. The study pinpoints the role of canopy architecture in berry water relations and stress response during ripening.

Today, more than 70 million tons of lignin are produced by the pulp and paper industry every year. However, the utilization of lignin as a source for chemical synthesis is still limited due to the complex and heterogeneous lignin structure. The purpose of this study was a selective photodegradation of industrially available kraft lignin in order to obtain appropriate fragments and building block chemicals for further utilization, e.g. polymerization. Thus, kraft lignin obtained from soft wood black liquor by acidification was dissolved in sodium hydroxide and irradiated at a wavelength of 254 nm with and without the presence of titanium dioxide in various concentrations. Analyses of the irradiated products via SEC showed decreasing molar masses and decreasing polydispersity indices over time. At the end of the irradiation period the lignin was depolymerised to form fragments as small as the lignin monomers. TOC analyses showed minimal mineralisation due to the depolymerisation process.

.With the increasing use of carbon fiber reinforced plastics in various area, carbon fiber composites based on prepregs have attracted attention in industries and academia research. However, prepreg manufacturing processes are costly, and the strength of structures varies depending on the orientation and defects (pores and delamination). For non-contact evaluation of internal defects, we proposed lock-in infrared thermography to investigate orientation angles after a compression test. We also conducted a drop-weight impact test to study the behaviour of the composites after impact according the fibers orientation for composite fabricated using unidirectional carbon fiber prepregs. Using CAI tests, we determined the residual compressive strength and confirmed the damage modes using a thermal camera. The results of the drop weight impact tests show that the specimen laminated at 0° suffered the largest damage because of susceptibility of the resin to impact. In contrast, the specimens oriented in of 0°/90° and +45°/–45° directions transferred more than 90% of the impact energy back to the impactor because of the lamination of fibers in the orthogonal directions. Furthermore, the specimens that underwent complete damage in the impact tests were subjected to the lock-in method and showed internal delamination and cut fibers. With the finite elements analysis, the damage of each ply could be observed. Moreover, the temperature differences in the residual compression tests were not significant.

In this paper, we propose and evaluate two mechanisms aimed at improving the communication reliability of IEEE 802.15g SUN (Smart Utility Networks) in industrial scenarios: RTS (Re-Transmission Shaping), which uses acknowledgements to track channel conditions and dynamically adapt the number of re-transmissions per packet, and AMS (Adaptive Modulation Selection), which makes use of reinforcement learning based on MAB (Multi-Armed Bandits) to choose the modulation that provides the best reliability for each packet re-transmission. The evaluation of both mechanisms is performed through computer simulations using a dataset obtained from a real-world deployment and two widely used metrics, the PDR (Packet Delivery Ratio) and the RNP (Required Number of Packet transmissions). The PDR measures the ratio between received and transmitted packets, whereas the RNP is the number of packet repetitions before a successful transmission. The results show that both mechanisms allow to increase the communication reliability while not jeopardizing the battery life-time constraints of end devices. For example, when three re-transmissions per packet are allowed, the PDR reaches 98/96\% with a RNP of 2.03/1.32 using RTS and AMS, respectively. Additionally, the combination of both proposed mechanisms allows to reach a 99% PDR with a RNP of 1.7, making IEEE 802.15.4g SUN compliant with the stringent data delivery requirements of industrial applications.

This study analyses regional development in one of the poorest provinces in China, Guizhou Province, between 2000 and 2012 using a multiscale and multi-mechanism framework. In general, regional inequality has been declining since 2000. In addition, economic development in Guizhou Province presented spatial agglomeration and club convergence, which shows how the development pattern of one core area, two-wing areas and a contiguous area at the edge of the province have been developed between 2006 and 2012. Multilevel regression analysis revealed that industrialization and investment level were the primary driving forces of regional economic disparity in Guizhou Province. The influences of marketization and decentralization on regional economic disparity were relatively weak. Investment level reinforced regional economic disparity and the development of core-periphery structure in the province. However, investment level actually weakened the regional economic disparity in Guizhou Province when the variable of time was considered. In addition, both the topography and urban–rural differentiation were the two main reasons for forming a core-periphery structure in Guizhou Province.

Urbanization-induced land use transition results in a decline in ecosystem services, which has implications for regional ecological security. In order to explore the relationship between ecosystem services and land use transition, this paper utilizes the InVEST model, geographically weighted regression model to examine the impact of land use transition on ecosystem services in the Dongting Lake area (DLA). The results showed that (1) During the period 2000-2020, the intensity and motivation of land-use transition showed obvious spatial and temporal heterogeneity with the variation of urbanization development. (2) Habitat quality and Carbon sequestrations showed a downward trend. In contrast, food supply followed an upward trend; soil conservation and water yield services initially increased and dropped later. The overall spatial changes in habitat quality and Carbon sequestration appear to be insignificant. Food supply shows significant differences in the plains compared to other areas; while soil conservation and water yield service shows significant changes in places other than the DLA. (3) From 2000 to 2020, land use transition dynamics, population density, GDP density, night lighting and transition intensity had mainly negative effects on ecosystem services. Only the Normalized Vegetation Index (NDVI) showed a positive effect on ecosystem services. The results of the research will provide valuable references for the development and implementation of spatial ecological restoration planning and land use policies in the national territory.

The pursuit of sustainable wellbeing is one of the research objectives of positive experience design. Driven by this goal, the purpose of this paper is to provide an impact-centered sustainable positive experience design model. Firstly, the literature review method was used to define the research status and concept of impact-centered sustainable design. Secondly, an impact-centered sustainable positive experience design model was constructed, and relevant formulas for concept generation and concept evaluation were proposed. Thirdly, design verification was conducted through a workshop. Finally, the Technology Acceptance Model (TAM) questionnaire was used to evaluate and discuss the design model. An impact-centered sustainable positive design model was proposed, which includes the important impact dimensions of sensory experience and meaningful experience on users’ quality of life at different levels: healthy living (pleasure index, health behavior), harmonious community (social connectivity, social contribution), and livable environment (living environment, environmental contribution). Based on positive experience related theory, this study takes long-term impacts as the starting point for sustainable positive experience design, which helps designers to generate design concepts from a systematic and long-term perspective.

This paper aims to investigate the rate of expansion and extraction within the solar system. We carried out the Solar system expansion calculations to do such a review. The Universe is expected to look the same from every point in it. After the big bang, Universe is expanding at some speed. Astrophysicists have been in a race to measure precisely how fast the Universe is expanding since Hubble announced that galaxies were systematically moving away from Milky Way Galaxy with a current speed in 1929. Hubble’s observations came after Einstein’s general relativity, which inspired the big bang theory. According to the Big Bang theory, the Universe has created billions of years ago with an explosion and started to expand until today. The expansion of the Universe mostly happens in vast spaces, so clusters of galaxies move away from each other. For example, raising bread during baking will expand, but the raisings will stay the same size while moving each other to expand the bread. Observers have proven that an object (galaxies, a cluster of planets) held together by gravity has a patch of nonexpanding space produced by a gravitational field. However, some observers claimed the solar system is not expanding, while others claimed it is expanding. Does our solar system expand in an expanding Universe? The cosmological expansion of local systems is reviewed in the modern cosmological models. We showed answers related to this question with the help of literature. This review article revisited the proof of the Solar System’s expansion and its speed with about 0.32 nm/s in an expanding Universe.

In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

Packet re-transmissions are a common technique to improve link reliability in low-power wireless networks. However, since packet re-transmissions increase the end-device energy consumption and the network load, a maximum number of re-transmissions per packet is typically set, also considering the duty-cycle limitations imposed by radio-frequency regulations. Moreover, the number of re-transmissions per packet is typically set to a constant value, meaning that all packet re-transmissions are treated the same regardless of actual channel conditions (i.e., multi-path propagation or internal/external interference effects). Taking that into account, in this paper we propose and evaluate the concept of re-transmission shaping, a mechanism that manages packet re-transmissions to maximize link reliability, while minimizing energy consumption and meeting radio-frequency regulation constraints. The proposed re-transmission shaping mechanism operates by keeping track of unused packet re-transmissions and allocating additional retransmission when the instantaneous link quality decreases due to channel impairments. To evaluate the re-transmission shaping mechanism we use trace-based simulations using a IEEE 802.15.4g SUN data-set and two widely used metrics, the PDR (Packet Delivery Ratio) and the RNP (Required Number of Packets). The obtained results show that re-transmission shaping is a useful mechanism to improve link reliability of low-power wireless communications, as it can increase PDR from 77.9% to 99.2% while sustaining a RNP of 2.35 re-transmissions per packet, when compared to using a single re-transmission per packet.

Intestinal commensal microbes, called the gut microbiota, play a critical role in host immune homeostasis through active microbial metabolites and innate and adaptive immune responses. Dysbiosis or imbalance of the gut microbiota composition is associated with inflammatory bowel disease (IBD) which includes Crohn’s disease and ulcerative colitis. The incidence and prevalence rates of IBD have been increasing worldwide. It is well recognized that butyrate, a microbial metabolite of diet fibers, is a major energy source for colonocytes and plays a crucial role in regulating immune function and maintaining epithelial barrier function and intestinal homeostasis. Emerging evidence suggests that butyrate might be a potential therapeutic agent to treat IBD. In this review, we discuss about gut microbial metabolites, particularly butyrate, the synthesis and metabolism of butyrate, mechanisms of butyrate in immune and epithelial barrier function. Furthermore, we review the current research on various therapeutic implications of butyrate in IBD.

Baobab (Adansonia digitata) leaves are usually used in dry form in the preparation of a soup known as ‘miyan kuka’ in Northern Nigeria. The leaves are believed to have nutritional and medicinal benefits and have been used for those purposes in Africa and Asia. However there has been limited research on the detailed constituents of the dry leaves. In this study, phytochemical, elemental and proximate analyses of stored, sun and shade-dried baobab leaves were conducted. The results revealed a great variation in the nutritional contents of the leaves. The study reveals that the leaves are rich in phytochemicals such as glycosides, saponins, steroids and flavonoids while alkaloids, tannins and resins are absent. Also, they are important source of minerals such as zinc, copper, iron and manganese. In addition, they are rich in fibre, crude protein, nitrogen and ash. Contrasting responses were obtained in the samples studied. The implications of these responses are discussed in relation to crop yield.

As the embedded device and internet of things (IoTs) concept prevalent in today's world, there is an increasing demand for the security and performance requirements on deploying these devices to private and public sectors. The crucial part of it is to protect privacy, confidentiality and integrity, meanwhile, maintain an adequate level of performance during transmission, storage and access of critical information. While the conventional cryptography methods, such as the Advanced Encryption Standard (AES), SHA$-$2 hashing method and RSA and Diffie Hellman for message authentication and identification, work well on systems which have reasonable processing power and memory capabilities. These do not scale well into a world with embedded systems and sensor networks, in conjunction with their nature of smaller size and lower cost. Thus, in the context of resource constrained device, lightweight cryptography methods are proposed to overcome many of the problems of conventional cryptography possessed. This includes constraints related to physical size, processing requirement, memory limitation, energy drain and production cost. This paper provides a survey of the architectures that are defined as replacements for conventional ciphers within an IoTs space and discuss some trends in the design of future lightweight algorithms. The performance metrics are carefully chosen to reflect and assess the suitability for embedded devices. The aim of this research is to identify the various performance metrics applied on different types of symmetric block ciphers especially lightweight ciphers and compare the results on versatile platforms with stream ciphers and public key methods. The comparative analysis on efficient LW cipher will be tested against other similar block ciphers on both MacBook Pro with Intel core and resource constrained device Raspberry Pi with ARM processor.

Sun glint, i.e., direct solar radiation reflected from a water surface, negatively affects the accuracy of ocean color retrieval schemes if entering the field-of-view of the observing instrument. Herein, a simple and robust method to quantify the sun glint contribution to top-of-atmosphere (TOA) reflectances in the visible (VIS) and near-infrared (NIR) is proposed, exploiting concomitant observations of the sun glint’s morphology in the shortwave infrared (SWIR) characterized by reflectance contrasts typically higher than those resulting from other in-water or atmospheric processes. The proposed method, termed Glint Removal through Contrast Minimization (GRCM), requires high spatial resolution (ca. 10–50 m) imagery to resolve the sun glint’s characteristic morphology, meeting additional criteria on radiometric resolution and temporal delay between the individual band’s acquisitions. It has been applied with good success to a selection of Landsat 8 (L8) Operational Land Imager (OLI) scenes encompassing a wide range of environmental conditions in terms of observation geometry and glint intensity, as well as aerosol and Rayleigh optical depth. The method proposed herein is entirely image based and does not require ancillary information on the sea surface roughness or related parameters (e.g., surface wind), neither the presence of clear water areas in the image under consideration. Limitations of the proposed method are discussed, and its potential for sensors other than OLI and applications beyond glint removal is sketched.

Biocides used in antifouling (AF) paints, such as 4,5-dichlorine-2-n-octyl-4-isothiazole-3-one (DCOIT), can gradually leach into the environment. Some AF compounds can persist in the marine environment and cause harmful effects on non-target organisms. Nanoengineered materials, such as mesoporous silica nanocapsules (SiNC) containing AF compounds, have been developed to control their release rate and reduce their toxicity to aquatic organisms. This study aimed to evaluate the acute toxicity of new nanoengineered materials, SiNC-DCOIT and a silver-coated form (SiNC-DCOIT-Ag), as well as the free form of DCOIT and empty nanocapsules (SiNC), on the sun coral Tubastraea coccinea. T. coccinea is an invasive species and can be an alternative test organism for evaluating the risks to native species, as most native corals are currently threatened. The colonies were collected from the Alcatrazes Archipelago, SP, Brazil, and acclimatized to laboratory conditions. They were exposed for 96h to different concentrations of the tested substances: 3.33, 10, 33, and 100 µg L-1 of free DCOIT; 500, 1000, 2000, and 4000 µg L-1 of SiNC; and 74.1, 222.2, 666.7, and 2000 µg L-1 of SiNC-DCOIT and SiNC-DCOIT-Ag. The test chambers consisted of 500 mL flasks containing the test solutions, and the tests were maintained under constant aeration, constant temperature of 23 ± 2°C, and photoperiod of 12h:12h (light/dark). At the end of the experiments, no lethal effect was observed; however, some sublethal effects were noticeable, such as the exposure of the skeleton in most of the concentrations and replicates, except for the controls, and embrittlement at higher concentrations. Adults of T. coccinea were considered little sensitive to the tested substances. This resistance may indicate a greater capacity for proliferation of the species, which is favored in substrates containing antifouling paints, to the detriment of the native species.

Adaptive mechanisms, such as channel hopping and packet replication, are used in low-power wireless networks to deal with the spatial and temporal variations in the link quality, and meet the reliability requirements of industrial applications (i.e., PDR>99%). However, the benefits of such mechanisms are limited and may have a large impact on end-to-end latency and energy consumption. Hence, in this paper we propose using adaptive modulation diversity, which allows to dynamically select different modulations, to improve link reliability. We present three adaptive modulation diversity selection strategies and validate them using the data derived from a real-world deployment using the IEEE 802.15.4g SUN modulations (i.e., SUN-FSK, SUN-OQPSK and SUN-ODFM) in an industrial environment. The results show that by using adaptive modulation diversity it is possible to improve link reliability regardless of node conditions.

A multimodal detection system with complementary capabilities for efficient detection was developed for impurity detection. The system consisted of a visible light camera, a multispectral camera, image correction and registration algorithms. It can obtain spectral feature and color feature at the same time, and has higher spatial resolution than a single spectral camera. This system was applied to detect impurities in Pu ’er tea to verify its high efficiency. The spectral and color features of each pixel in the images of Pu ’er tea were obtained by this system and used for pixel classification. The experimental results show that the accuracy of Support Vector Machine (SVM) model based on combined features is 93%, which is 7% higher than that based on only spectral features. By applying median filtering algorithm and contour detection algorithm to the label matrix extracted from pixel-classified images, 8 impurities except hair were detected successfully. Moreover, taking advantage of the high resolution of visible light camera, small impurities can be clearly imaged. By comparing the segmented color image with the pixel-classified image, small impurities such as hair could be detected successfully. Finally, it is proved that the system can obtain multiple images to allow a more detailed and comprehensive understanding of the detected items, and has excellent ability to detect small impurities.

To achieve user retention through multifactor synergy, Internet enterprises must reduce costs and increase efficiency and sustainable development. In response to the dilemma that Internet compa-nies are experiencing increasingly high user acquisition costs and serious user churn, this paper uses a sample of 46,695 user reviews of nine product series from Xiaomi Ecological Chain. Case studies and qualitative comparative analysis are used to explore the influence mechanisms of quality of experience, brand trust, and brand attachment on users' retention intentions. Our find-ings are as follows. (1) Brand attachment alone is not necessary for high user retention intention, but user perception, cognition, and brand trust are necessary. (2) Quality of experience positively impacts brand trust, attachment, and user retention intention. Therefore, improving user perception and cognition is critical in generating high user retention intention. (3) Five configuration paths can achieve high user retention intention, three configuration paths lead to low user retention intention, and there is an asymmetric relationship between these paths. Among them, the role of quality of experience-driven configuration paths in generating user retention intention is the most prominent. (4) In the substitution relationship between configuration paths, user perception, and cognition can substitute with brand trust and attachment. Our findings have important theoretical and practical implications for revealing the realization paths of high user retention intention in Internet companies and provide a new perspective for future research.

Purpose: To clarify the mechanism of state anxiety on intertemporal decision-making, two studies were conducted to investigate the role of trait anxiety and inhibitory control. Study 1 examined the moderating effect of trait anxiety. Study 2 continued to investigate the mediating effect of inhibition control on the basis of study 1. Methods: A total of 266 Chinese college students participated. Participants’ state anxiety, trait anxiety and intertemporal decision-making were measured by questionnaires (scales) respectively. And inhibition control was evaluated by two-choice oddball paradigm. Results: The results of Study 1 indicated that state anxiety could predict intertemporal decision-making and that the moderating effect of trait anxiety on this relationship was significant. Study 2 found that inhibitory control could completely moderate the relationship between state anxiety and intertemporal decision-making and that this indirect effect was affected by trait anxiety. Conclusion: 1)Individuals with higher trait anxiety are more inclined to make more impulsive and intertemporal decisions when they have a high level of state anxiety; 2)state anxiety allows inhibitory control ability to have a further effect on intertemporal decision-making; and 3)the higher trait anxiety in individuals, the stronger mediating effect of inhibitory control on the relationship between state anxiety and intertemporal decision-making.

We present a plausible solution to the now forty seven year old paleoclimatology riddle of the so-called Faint Young Sun Paradox via the combined hypothesis of the conservation of the state of radiation balance between the Earth and Sun and that of an expanding Earth, where, in the face of a changing (increasing) Solar luminosity, the Earth would maintain steady temperatures by re-adjusting the height of its atmosphere. That is to say, depending on whether or not the radius of the solid Earth is changing, this re-adjustment of the height of the Earth’s atmosphere would mean two things — i.e.: (1) either the height increases — in which event the Earth accretes matter from its immediate surroundings (i.e., the obvious pool formed by the Solar wind) thereby increasing the mass of the Earth’s atmosphere, or: (2) the height decreases — in which event the Earth naturally expels matter from its atmosphere, thereby decreasing the effective mass of the Earth. We demonstrate that if –- as the current state of the art ITRF observations seem to indicate, namely that — the Earth’s landmass is steadily expanding globally at a paltry rate of ∼+0.45±0.05mm·yr−1, and, that the Earth’s atmosphere is to have a present radial vertical height of about one third of the Earth’s radius (∼2860km) from the Earth’s surface, then, one can (might) with relative ease, explain not only the presence of liquid water on the Earth’s surface some ∼3.20±0.70Gyr ago during the Archaean eon when the Sun was about 75% of its current luminosity, but also the present radial expansion rate of the Earth. When all is said and done, the Earth system is herein cast as an auto-self-regulating incubator where the auto-self-regulating mechanism is as a result of the Earth’s atmosphere responding by automatically re-adjusting its height.

A new quinazolinone alkaloid, named peniquinazolinone A (1), as well as eleven known com-pounds, 2-(2-hydroxy-3-phenylpropionamido)-N-methylbenzamide (2), viridicatin (3), viridicatol (4), (±)-cyclopeptin (5a/5b), dehydrocyclopeptin (6), cyclopenin (7), cyclopenol (8), methyl-indole-3-carboxylate (9), 2,5-dihydroxyphenyl acetate (10), methyl m-hydroxyphenylacetate (11), conidiogenone B (12), was isolated from the endophytic Penicillium sp. HJT-A-6. The chemical structures of all compounds were elucidated by comprehensive spectroscopic analysis, including 1D, 2D NMR, and HRESIMS. The absolute configuration at C-13 of peniquinazolinone A (1) was established by applying the modified Mosher’s method. Compounds 2, 3, and 7 exhibited an op-timal promoting effect on the seed germination of Rhodiola tibetica at a concentration of 0.01 mg/mL, while the optimal concentration for compounds 4 and 9 to promote Rhodiola tibetica seed germination was 0.001 mg/mL. Compound 12 showed optimal seed-germination-promoting activity at a concentration of 0.1 mg/mL. Compared with the positive drug 6-benzyladenine (6-BA), compounds 2, 3, 4, 7, 9, and 12 could extend the seed-germination period of Rhodiola tibetica up to the 11th day.

The TiO₂ nanostructures resulted by pyrolysis of TiCl₄ at low temperature of 80 ^oC are found to be a mixture of amorphous TiO₂ complexes and anatase nanostructure whose ratio depends on the pH of the pyrolysis medium. At low pH level, the resulting TiO₂ nanostructure is predominant anatase and gradually shifts to the amorphous TiO₂ complexes with pH level increasing. By means of heat treatment, the amorphous TiO₂ complexes can be converted back to the anatase nanostructure and then transform to rutile with the elevating temperature. Amongst of the TiO₂ nanostructure recovered from amorphous TiO₂ complexes, the anatase shows to be the most effective photocatalyst in decomposition of methylene blue.

Porous tantalum (Ta) is a promising biomaterial and has been applied in orthopedics and dentistry for nearly two decades. The high porosity and interconnected pore structure of porous Ta promise fine bone ingrowth and new bone formation within the inner space, which further guarantee rapid osteointegration and bone-implant stability in long term. Porous Ta has high wettability and surface energy that can facilitate adherence, proliferation and mineralization of osteoblasts. Meanwhile, low elastic modulus and high friction coefficient of porous Ta can effectively avoid stress shield effect, minimize marginal bone loss and ensure primary stability. Accordingly, the satisfactory clinical application of porous Ta based implants or prostheses are mainly derived from its excellent biological and mechanical properties. With the advent of additive manufacturing, personalized porous Ta based implants or prostheses have shown their clinical value in the treatment of individual patient who need specially designed implant or prosthesis. In addition, many modification methods have been introduced to enhance the bioactivity and antibacterial property of porous Ta with promising in vitro and in vivo research results. In any case, choosing suitable patients is of great importance to guarantee surgical success after porous Ta insertion.

Knee osteoarthritis is the most popular type of osteoarthritis that causes extreme pain in elderly. Currently there is no cure for osteoarthritis. To lessen clinical symptoms, glucosamine was suggested. The primary goal of our study is to evaluate the efficacy and safety of glucosamine from recent studies. Electronic databases such as PubMed, Scopus, Cochrane were used to assess RCT. From the beginning through March 2023, the papers were checked, and if they fulfilled the inclusion criteria, they were then examined. WOMAC and VAS scales were considered as main outcome measure. A total of 15 studies were selected. Global pain was significantly decreased in comparison to placebo, as measured by the VAS index, with an overall effect size SMD of -7.41 ([95% CI] 14.31, 0.51). The WOMAC scale confirmed that pain, stiffness, and physical function had improved, however the effects were insufficient. A statistical update also revealed that there were no reports of serious medication interactions or significant adverse events. To summarize, glucosamine is more effective than a placebo at reducing pain in knee osteoarthritis patients. In long-term treatment, oral glucosamine sulfate 1500 mg/day is believed to be well tolerated.

Background: Ultraviolet (UV) radiation from the sunlight can harm skin cells, causing short-term effects, such as sunburns and long-term effects, such as pigmentation changes, changes in the skin's immune responses, and increased risk of skin cancer. These conditions can be largely prevented with proper sun protection measures and behavioural changes. This study aims to assess the knowledge on sun protection behaviour and baseline knowledge of medical students from the “Carol Davila” University of Medicine and Pharmacy, Bucharest, Romania. Methods: Data in this cross-sectional study were collected through a Google Forms questionnaire, which was distributed from November 2023 to December 2023 via digital communication channels to students across all academic years. STROBE guidelines were consulted for data synthesis; Results: A total of 668 stu-dents responded. The student cohort demonstrated a commendable level of awareness of the risks associated with sun exposure and the advantages of employing sun protection factor (SPF); how-ever, the incidence of sunburns remained notably elevated (72.3%). Further analysis revealed cor-relations among gender, academic year, presence of photosensitizing conditions, and adherence to SPF application. Additionally, there is a need to improve understanding of the appropriate appli-cation techniques for SPF, as only 11.5% of the students exhibited proficiency in this regard; Con-clusions: As future healthcare providers, medical students hold significance in promoting healthy behaviours in the broader community. This study indicates that while their knowledge about sun protection is satisfactory, there is scope for enhancement.

In this article we present a deployment of 11 nodes using the three different SUN (Smart Utility Network) modulation schemes, as defined in the IEEE 802.15.4-2015 standard. The nodes were deployed in a 110.044 m2 warehouse for 99 days, and the resulting dataset contains a total of 10.710.868 measurements with RSSI (Received Signal Strength Indicator), CCA (Clear Channel Assessment) and PDR (Packet Delivery Ratio) values. The analyzed results show a high variability in average RSSI (i.e., between -82.1 dBm and -101.7 dBm) and CCA (i.e., between -111.2 dBm and -119.9 dBm) values, which are caused by the effects of multi-path propagation and external interference. Despite being above the sensitivity limit for each modulation, this values result in poor average PDR values (i.e., from 65.9% to 87.4%), indicating that additional schemes are required for low-power wireless communications to meet the dependability requirements of industrial applications. For that purpose, we also introduce the concept of modulation diversity, which can be combined with packet repetition to meet such requirements (i.e., PDR>99%) while minimizing the energy expenditure of nodes and meeting regulatory constraints.

Pavement crack detection is one of the key links in highway pavement maintenance management. In the current road crack detection, the network model easily ignores the shallow geometric features of cracks and cannot extract the key feature information of cracks. Aiming at the above problems, an EC-YOLOX network model is proposed. The CFPN is constructed to cross-fuse different scale features to solve the feature scale invariance. In the strengthen feature extraction layer, ECANet is fused to enhance the ability to pay attention to key information. The WEIoU loss function is proposed, which assigns different penalty terms to the target box in the vertical and horizontal directions. In terms of data, geometric distortion constraint correction is performed on the single-point perspective pavement image. The experimental data show that the accuracy of EC-YOLOX on the self-built data set reaches 76.34% [email protected], which is 4.45% higher than that of YOLOX. The loss curve of EC-YOLOX is smoother than that of YOLOX, and the minimum training loss value is 2.136, which is 0.648 lower than the minimum loss value 2.784 of YOLOX. Many experiments have verified the effectiveness of EC-YOLOX in improving the detection effect in pavement crack detection.

Head and neck squamous cell carcinoma (HNSCC) is a type of cancer that arises from the epithelium lining of the oral cavity, hypopharynx, oropharynx, and larynx. Despite advancement of the current treatment to HNSCC, such as surgery, chemotherapy, and radiotherapy, the overall survival rate of HNSCC remains poor due to late diagnosis and acquired resistance to treatment. Natural products have been extensively explored as a safer and more acceptable alternative to current treatments, with numerous studies displaying their potential against HNSCC. This review highlights preclinical studies in the past 5 years involving natural products against HNSCC and explores the signalling pathways altered by these products. This review also addresses challenges and future directions of the use of natural products as chemotherapeutic and chemoprevention agents against HNSCC.

The attitude dynamics and orbit dynamics of large rigid space structures are coupled with each other under gravity gradient, which may affect the stability of the large rigid space structures. In this paper, the gravity gradient stability of a large rigid space structure is studied under both small and large disturbances. Based on the rigid body dynamics and orbit dynamics, an accurate dynamic model without any linearization of the large rigid space structure is established via the natural coordinate formulation (NCF), which is able to describe the large overall motions of the structures. By using the generalized-α algorithm, the gravity gradient stability of the large rigid space structure is simulated and analyzed via various examples, including the influence of large disturbance angles, the positions at the stabilization and unstabilization regions. Finally, the relationship between spinning stability and gravity gradient stability is also investigated via a large spinning space structure.

In recent years, the rapid development of computer-aided planning and design technology has provided a new perspective for the study of complex problems such as the generation of architectural complex forms. This study focuses on how to apply parameterization technology to analyze and articulate traditional spatial form composition rules, aiming to minimize reliance on subjective human judgment in the protection and renewal design of the historical style of traditional villages. It aims to establish digital generative design tools to address the challenges of accurately inheriting and innovatively utilizing historical and cultural information in traditional settlements. It introduces how to rely on parameterization technology to analyze the spatial form composition rules, parameter extraction rules, and spatial reconstruction rules of traditional villages, facilitating the complete process from spatial features to parameterization rules, and then to the application of computational methods to deduce spatial features. It also includes case studies demonstrating the application of parameterization technology tools for village protection and explores the role of generative design tools in preserving the spatial style of these settlements.

Alternative fertilizations are essential to minimize the deteriorating effects of chemical fertilizers on soil and water quality/health. Accordingly, the present work investigated the effects of combined organic-inorganic fertilization (COIF) on wheat and rice yields, soil nutrients, and soil Cd accumulation. Hence, seven different treatments were set up: control (CK); conventional fertilization (CF); optimized fertilization (OF); organic fertilizer replacing 25% (T1) and 50% (T2) of OF; and organic nitrogen (N) replacing 25% (M1) and 50% (M2) of OF-N. Overall, significant increases occurred in the yields of COIF crops. Compared with the CF, the highest wheat and rice yields happened in M1 treatment (approximately by18.5%) (P < 0.05). COIF slightly alleviated soil acidification, and improved the cation exchange capacity (CEC) of the study soils. Besides, COIF treatments significantly increased the contents of total phosphorus, total potassium, available phosphorus, and available potassium by 6.35 to 16.9 %, 3.17 to 10.9 %, 5.53 to 28.7 %, and 2.6 to 12 %, respectively (P <0.05). Nevertheless, negligible increases took place in Cd content of COIF soils compared with the CK. Altogether, our results concluded on 25% replacement of OF-N by organic N (M1) to effectively improve the fertility/ecological sustainability of the study soils.

As a renewable industrial crop, Miscanthus offers numerous advantages, namely high photosynthesis activity (as a C4 plant) and exceptional CO2 fixation rate. These properties make Miscanthus very attractive for industrial exploitation, such as lignin generation. Here, we present a systematic study analyzing the correlation of the lignin structure with Miscanthus genotype and plant portion (stem versus leaf). Specifically, the ratio of the three monolignols and corresponding building blocks as well as the linkages formed between the units have been studied. Depending on the Miscanthus genotype and plant component (leaf versus stem), correlations between chemical structure and properties of the lignins have been determined, i.e. correlations in molecular weight, polydispersity and decomposition temperature. Lignin isolation was performed using non-catalyzed organosolv pulping and the structure analysis includes NREL, FTIR, UV-Vis, HSQC-NMR, TGA, pyrolysis GC/MS. Structural differences were found for stem and leaf-derived lignins. Compared to beech wood lignins, Miscanthus lignins possess lower molecular weight and narrow polydispersities (< 1.5 Miscanthus vs. > 2.5 beech) corresponding to improved homogeneity. In addition to conventional univariate analysis of FTIR spectra, multivariate chemometrics revealed distinct differences for aromatic in-plane deformations of stem versus leaf-derived lignins. These results emphasize the potential of Miscanthus as low-input resource and Miscanthus-derived lignin as promising agricultural feedstock.

Gelidium jelly was traditionally made by boiling processed Gelidium seaweed and allowing the filtrate to congeal into jelly. The processing of Gelidium seaweed was very complicate involved the repeated procedures of water washing and sun drying for 7 times, and the seaweed was originally purple-red in color turned into yellow after the repeated wash and sun drying. This study aimed to evaluate the effects of halogen lamp drying methods in replace of sun drying on the physical-chemical qualities of Gelidium jellies. Properties included the agar yield, gelling temperature, hardness, springiness, rheological parameters, sensory attributes, color, and volatile compounds were investigated. The results demonstrated halogen lamp drying method required 12 times of washing and drying processes to achieve the similar jelly properties compared to sun drying for 7 times in the experimental conditions. Volatiles including heptanal, β-ionone, and (E)-2-decenal could be used as indicators to monitor the washing and drying processing. Halogen lamp was found could be an alternative processing method for seaweed drying, especially at rainy days.

If environmental exposures are shown to cause an adverse health outcome, reducing exposure should reduce the disease risk. Links between exposures and outcomes are typically based on ‘associations’ derived from observational studies, and causality may not be clear. Randomised controlled trials to ‘prove’ causality are often not feasible or ethical. Here the history of evidence that tobacco smoking causes lung cancer – in observational studies – is compared to that of low sun exposure and/or low vitamin D status as causal risk factors for the autoimmune disease, multiple sclerosis. Evidence derives from in vitro and animal studies, as well as ecological, case-control and cohort studies, in order of increasing strength. For smoking and lung cancer, the associations are strong, consistent, and biologically plausible – the evidence is coherent or ‘in harmony’. For low sun exposure/vitamin D as risk factors for MS, the evidence is weaker, with smaller effect sizes, but coherent across a range of sources of evidence, and biologically plausible. The association is less direct – smoking is directly toxic and carcinogenic to the lung, but sun exposure/vitamin D modulate the immune system, which in turn may reduce the risk of immune attack on self-proteins in the central nervous system. Opinion about whether there is sufficient evidence to conclude that low sun exposure/vitamin D increase the risk of multiple sclerosis, is divided. General public health advice to receive sufficient sun exposure to avoid vitamin D deficiency (<50nmol/L) should also ensure any benefits for multiple sclerosis.

Australia and New Zealand have the highest incidence of skin cancer. Sport is a fundamental part of Australasian culture, beginning in childhood, often with life-long participation. Participating in outdoor sports can contribute significantly to the lifetime ultraviolet radiation (UVR) dose individuals receive and their risk of developing skin cancer. This systematic scoping review explores the use of sun-protection by outdoor sporting participants in Australasia and considers how sun-protection practices may be better evaluated and improved in the community. A search of electronic databases using the search strategy “sun protection” AND “sport” AND “Australia” yielded 17 studies published in English from January 1992 to August 2021. Study methods included using UV-dosimeters to measure individual UVR-exposure; remote estimates of clothing-adjusted UVR-exposure; direct observation of sun-protection practices; and self-reported sun-exposure and sun-protection. Despite 40-years of ‘Slip Slop Slap’ campaigns in Australia, the use of sun-protection in most outdoor sports is inadequate. The paucity of comparable data limited our analyses, demonstrating a need for standardized, objective evaluation tools. Such tools, if used across a range of sports, should inform the development of workable recommendations that sporting clubs could implement and adopt into policy, thus empowering them to better protect the health of their participants.

SARS-CoV2 (corona virus) has spread globally at an unprecedented rate; so far, increasing SARS-CoV2-infected individuals have been identified. Although the situation in China is improving and is currently under control, the outbreak in other countries and its pandemic management is only beginning to develop. Based on 154 SARS-CoV2 genome sequence analyses, we used receptor–ligand docking to identify one potential point mutation (V354F) on the spike structure which enhances spike binding to ACE2 receptors underlying potential super infection. Importantly, the V354F site on spike S1 had been identified in 5/10 infected French patients living in Paris, who sharing 100% identical SARS-CoV2 genomes. With Covid-19 cases increasing rapidly in France that could lead to a new explosion, we suggest that the French government should identify all potential super spreaders and treat them accordingly. In summary, our study provides on of the measures to avoid the potential second worldwide explosion of SARS-CoV2.

The antiradical and antimicrobial activity of lignin and lignin-based films are both of great interest for applications such as food packaging additives. The polyphenol structure of lignin in addition to the presence of O-containing functional groups is potentially responsible for these activities. This study used DPPH assays to discuss the antiradical activity of HPMC/lignin and HPMC/lignin/chitosan films. The scavenging activity (SA) of both binary (HPMC/lignin) and ternary (HPMC/lignin/chitosan) systems was affected by the percentage of the added lignin: the 5% addition showed the highest activity and the 30% addition had the lowest. Both, scavenging activity and antimicrobial activity are depending on the biomass source showing the following trend: organosolv of softwood > Kraft of softwood > organosolv of grass. Testing the antimicrobial activities of lignins and lignin-containing films showed high antimicrobial activities against gram-positive and gram-negative bacteria at 35 °C and at low temperatures (0-7 °C). Purification of kraft lignin has a negative effect on the antimicrobial activity while storage has positive effect. The lignin release in the produced films affected the activity positively and the chitosan addition enhances the activity even more for both gram-positive and gram-negative bacteria. Testing the films against spoilage bacteria that grow at low temperatures revealed the activity of the 30% addition on HPMC/L1 film against both B. thermosphacta and P. fluorescens while L5 was active only against B. thermosphacta. In HPMC/lignin/chitosan films the 5% addition exhibited activity against both B. thermosphacta and P. fluorescens.

In this article, we present the use of the coupled land surface model and groundwater flow model SWAT-MODFLOW with the decision support tool WEAP (Water Evaluation and Planning software) to predict future surface water abstraction scenarios in a complex river basin, under conditions of climate change. The modeling framework is applied to the Dee River catchment in Wales, United Kingdom. Regarding hydrology, the coupled model improves overall water balance and low streamflow conditions, compared to a stand-alone SWAT model. The calibrated SWAT-MODFLOW is employed with high resolution climate model data from the UKCP18 project with future scenario of RCP85 from 2020 to 2040. Then, water supply results from SWAT-MODFLOW are fed into WEAP as input for the river reach in the downstream region of the river basin. This system is utilized to create various future scenarios of surface water abstraction of public water supply in the downstream region: maximum licensed withdraw, 50 % authorized abstractions, monthly time series with 1% increase of water use, and maximum water withdraw year based on historical records repeated every year with 1% increase of water use, to estimate the unmet demands and streamflow requirement. This modeling approach can be used in other river basins to manage scenarios of supply and demand.

Robotic path planning is a field of research which is gaining traction given the broad domains of interest to which path planning is an important systemic requirement; the aim being to optimise the efficacy of robotic movements in a defined operational environment. For example, robots have been employed in many domains including: cleaning robots (such as vacuum cleaners), automated paint spraying robots, window cleaning robots, forest monitoring robots, agricultural robots (often driven using satellite and geostationary positional satellite data). Additionally, mobile robotic systems have been utilised in disaster areas and locations hazardous to humans (such as war zones in mine clearance). The coverage path planning problem describes an approach which is designed to determine the path that traverses all points in a defined operational environment while avoiding static and dynamic (moving) obstacles. In this paper we present our proposed Smooth-STC model, the aim of the model being to identify an optimal path, avoid all obstacles, prevent (or at least minimise) backtracking, and maximise the coverage in any defined operational environment. The experimental results in a simulation show that, in uncertain environments, our proposed smooth STC method achieves an almost absolute coverage rate and demonstrates improvement when measured against alternative conventional algorithms.

This study assesses the biomethane (CH4) generation and greenhouse gas (GHG) emissions resulting from municipal solid waste landfilling in Phnom Penh, Cambodia, with a focus on the impact of fugitive CH4 emissions and operation processes in four landfilling scenarios: simple dumping (S1), improved management with leachate treatment (S2), engineered landfill with flaring (S3), and engineered landfill with energy recovery (S4). The study also considered the environmental benefits of carbon sequestration and landfill gas utilization. The LandGEM and IPCC FOD models were used to calculate CH4 generation over the period of 2009-2022, and it was found that approximately 18 and 21 M kg/year of CH4 are released, respectively. The energy potential from CH4 recovery was 51–61 GWh/year. Overall GHG emissions in S2 were the highest, amounting to 409–509 M kg CO2-eq/year, while S1 had lower emissions at 397–496 M kg CO2-eq/year. Flaring captured CH4 in S3 could reduce GHG emissions by at least 55%, and using captured CH4 for electricity production in S4 could mitigate at least 83% of GHG emissions. Electricity recovery (S4) could avoid significant amounts of GHG emissions (˗104.5 kg CO2-eq/tMSW). The study suggests that landfill gas-to-energy could significantly reduce GHG emissions.

The COVID-19 pandemic has expanded globally and caused serious consequence in both health system and the economy. MPV is one of two oral antivirals for COVID-19 with mild-to-moderate symptoms that have received FDA approval so far. This study aims to evaluate the cost-utility of using MPV in COVID-19 treatment. To compare the utility costs of MPV and non-MPV treatments for COVID-19 patients, we used a decision tree model. Data on clinical efficacy, cost, and quality of life were gathered from previous studies. The incremental effective cost ratio (ICER) calculated based on costs incurred and quality-adjusted life years (QALY), was considered as primary out-come. The total cost of MPV treatment and not using MPV was 15,362,516 VND (618 USD) and 15,771,262 VND (634 USD), respectively. The estimated QALY with using-MPV was 28.33, while without MPV was 19.72. The ICER was dominant, resulting in savings of 47,453 VND/QALY (1.9 USD). MPV is a cost-effective medication used to treat COVID-19. In mild-to-moderate COVID-19 patients, MPV considerably lowers costs and improves quality of life. However, several clinical factors of the drug still need to be taken into account.

The sun bear is conservation mammal in Indonesia. The ecological problems as conflict among mammals and human often happen around wildlife, the one of the case is the conflict between sun bear (helarctos malayanus) with human. In Pasaman where around the anthropogenic landscape is bounded by natural forest as sun bear habitat. In this decade, the story has recorded about ±16 incidents. The aim of this research is to geospatial modeling the area of potential conflict between sun bear- human. The method in this research is to use natural logarithmic and regression logistic. The tool is geographical information system and maximum entropy. The result of this research, there has found the distribute energy each variable landscape ecosystem. The statistical model of the potential conflict it has spread on landscape ecosystem. The average value of AUC prediction in this model is at number of 0.91. The variable contribution which affect are forest edge at number of 39.2%, the alternative food (plantation) at number of 31.4%, and forest fragmentation at number of 16.9%.

The IEEE 802.15.4-2015 standard includes the SUN (Smart Utility Networks) modulations, i.e., SUN-FSK, SUN-OQPSK and SUN-OFDM, which provide long range communications and allow to trade data rate, occupied bandwidth and reliability. However, given the constraints of low-power devices and the challenges of the wireless channel, communication reliability cannot still meet the PDR (Packet Delivery Ratio) requirements of industrial applications, i.e., PDR>99%. Hence, in this paper we evaluate the benefits of improving communication reliability by combining packet transmissions with modulation diversity using multiple IEEE 802.15.4g SUN modulations. The results derived from a real-world deployment show that going from 1 to 3 packet transmissions with the same SUN modulation can increase PDR from 85.0/84.6/71.3% to 94.2/94.1/86.0% using SUN-FSK, SUN-OQPSK and SUN-OFDM, respectively. Combining the same number of packet transmissions with modulation diversity allows to further increase the average PDR to 97.1%, indicating its potential as a tool to help meeting the reliability requirements of industrial applications.

With the increasing of China's international status and the acceleration of the process of global economic integration, the internationalization strategy of Chinese enterprises is getting deeper and deeper. This paper analyzes the problems and challenges faced by the international supply chain management of Chinese bamboo weaving and creative products, and puts forward a set of supply chain management model that ADAPTS to the international development. Firstly, the concept, connotation and types of supply chain management are sorted out through literature review. Secondly, this paper analyzes the current situation of international supply chain management of bamboo editing and creative products, and points out the existing problems. Thirdly, based on the theory and practice of international supply chain management, this paper puts forward a set of supply chain management model suitable for the international development of bamboo editing and creative products. Finally, taking a bamboo weaving and creative products enterprise as an example, the application effect of the supply chain management model is empirically analyzed. The results show that the supply chain management model can effectively reduce the cost and improve the efficiency, and is conducive to the international development of bamboo editing and creative products.

The reliance on cloud computing services and related technologies has increased due to their many benefits, including resource sharing and the need for organizations to maintain their competitive advantage in the digital market. Also, the pace of cloud growth has significantly increased because of COVID-19. Many companies and businesses have shifted their core processes to the cloud for seamless operations during the pandemic. This migration of legacy systems to the cloud creates many opportunities for businesses. However, on the other hand, it may also bring substantial challenges. Hence, a careful decision is needed to align with company goals. In this paper, we demonstrate the need and advantages of cloud computing, followed by highlighting AWS's characteristics as one of the leading cloud service providers. We also discuss the merger of AWS with SDN to improve cloud data security and performance. The outcomes of this study can provide a data migration strategy and guide decision-makers toward a secure and sustainable migration to a cloud computing environment.

Rapid urbanization has dramatically spurred the economic development over the past three decades, especially in China, but has nevertheless had negative impacts on natural resources since it is an irreversible process. Thus, it is essential to timely monitor and quantitatively analysis the changes in land use over time and to identify the landscape pattern variation related to growth mode in different period. This study aims at inspecting spatiotemporal characteristics of landscape pattern respond to land use changes in Xuzhou city during the period from 1985 to 2015. In this connection, we proposed a new spectral index, named the Normalized Difference Enhanced Urban Index (NDEUI), which combines data from NTL (Nighttime light) from the Defense Meteorological Satellite Program/Operational Linescan System (DMSP/OLS) with annual maximum Enhanced Vegetation Index (EVI) to reduce the detection confusion between urban areas and barren land, as well as follows. NDEUI-assisted Random Forests algorithm was implemented to obtain the land use/land cover (LULC) maps of Xuzhou in 1985, 1995, 2005 and 2015, respectively. Here, four different periods viz. 1985–1995, 1995–2005, 2005–2015 and 1985–2015 are chosen for the change analysis of land use and landscape pattern. The results indicated that the urban area has increased by about 30.65%, 10.54%, 68.77%, and 143.75% during the four periods mentioned above at the main expense of agricultural land, respectively. The spatial trend maps revealed that continuous transition from other land use types into urban land has appeared a dual-core development mode throughout the urbanization process, located at the new city region and the Jiawang district, mainly affected by the construction of new city region, freeway and the high railway station. Furthermore, we quantified the patch complexity, aggregation, connectivity and diversity of landscape employing a number of landscape metrics to represent the changes of landscape pattern at both class and landscape level, affected by urbanization during the study period. The results showed that with regard to the four aspects of landscape pattern, there were considerable differences among the four years, mainly owing to the increasing dominance of urbanized land. Spatiotemporal variation of landscape pattern was also conducted on the basis of subgrids in 900 m × 900 m. Combined with the land use changes and spatiotemporal variation of landscape pattern, it can be concluded that different urbanization modes and intensity result in variously the spatiotemporal evolution of landscape patterns. For Xuzhou city, the urban growth mainly appeared a leapfrog mode alone both sides of the roads during the period of 1985 to 1995, and then shifted into edge-expansion mode during the period from 1995 to 2005, whereas the edge-expansion and leapfrog modes coexisted for the period from 2005 to 2015. The high valuable spatiotemporal information generated utilizing RS and GIS in this study may give assistance to urban planners and policymakers to well understand urban dynamics and evaluate their spatiotemporal and environmental impacts at a local level for the sake of sustainable urban planning in the future.

To explore the effects of pymetrozine on the reproductive behavior of N. lugens, we established a bioassay method to accurately evaluate the toxicity of pymetrozine in N. lugens and establish the level of pymetrozine resistance of N. lugens in the field. In this study, pymetrozine’s effects on the fecundity of N. lugens were evaluated using the topical application method and rice-seedling dipping method. Moreover, the resistance of N. lugens to pymetrozine in a pymetrozine-resistant strain (Pym-R) and two field populations (YZ21 and QS21) was determined using the rice-seedling dipping method and fecundity assay methods. The results showed that treatment of N. lugens third-instar nymphs with LC15, LC50, and LC85 doses of pymetrozine resulted in significantly reduced male fertility and female fecundity. In addition, N. lugens adults treated with pymetrozine using the rice-seedling dipping and topical application method also exhibited significantly in-hibited male courtship, fertility, and female receptivity. Using the rice-stem dipping method, pymetrozine resistance was shown to be at high levels in Pym-R (194.6-fold), YZ21 (205.9-fold), and QS21 (212.8-fold), with LC50 values of 522.520 mg/L (Pym-R), 552.962 mg/L (YZ21), and 571.315 (QS21) mg/L. However, when using the rice-seedling dipping or topical application fe-cundity assay method, Pym-R (EC50: 14.370 mg/L, RR=12.4-fold; ED50: 0.560 ng/adult, RR=10.8-fold), YZ21 (EC50: 12.890 mg/L, RR=11.2-fold; ED50: 0.280 ng/adult; RR=5.4-fold), and QS21 (EC50: 13.70 mg/L, RR=11.9-fold) exhibited moderate or low levels of resistance to pymet-rozine. Our studies show that pymetrozine can significantly inhibit the fecundity of N. lugens. The fecundity assay results showed that N. lugens only developed low to moderate levels of resistance to pymetrozine, indicating that pymetrozine can still achieve effective control on the next gen-eration of N. lugens populations.

Background. There is limited evidence on the relationship between chronic kidney disease (CKD) and frailty in older people in Vietnam. This study aimed to examine the prevalence of frailty and its impact on mortality in older patients with end-stage renal disease. Method. This is a prospective, observational study at two large Dialysis Centres in Vietnam from November 2020 to June 2021. Consecutive older patients diagnosed with end-stage renal disease and on dialysis were recruited. Participants’ frailty status was defined by the Clinical Frailty Scale (CFS). The study outcome was all-cause mortality at 6th month. Results. A total of 175 participants were recruited (mean age 72.4 years, 58.9% female). Using the cut-point of CFS ≥4, 87.4% of the participants were frail. Mortality at 6th month was 14.9%, 31.9% in participants with CFS ≥7, 12.8% in participants with CFS=6, 7.5% in participants with CFS from 4 to 5, and 4.5% in participants with CFS ≤3 (p=0.001). Cox regression analysis showed that compared to the non-frail participants, the probability of death over 6 months was nearly 2-fold higher in the mildly frail, 3-fold higher in the moderately frail, and 9-fold higher in the severely frail participants. Conclusion. This study demonstrated a very high prevalence of frailty in older patients with end-stage renal disease and dialysis and the significant impact of frailty severity on mortality. Healthcare providers should consider incorporating frailty screening into routine care for older patients with end-stage renal disease and dialysis.

It's challenging to achieve robust lane detection depending on single frame when considering complicated scenarios. In order to detect more credible lane markings by using sequential frames, a novel approach to fusing vision and Inertial Measurement Unit (IMU) is proposed in this paper. The hough space is employed as the space where lane markings are stored and it's calculated by three steps. Firstly, a basic hough space is extracted by Hough Transform and primary line segments are extracted from it. In order to measure the possibility about line segments belong to lane markings, a CNNs based classifier is introduced to transform the basic hough space into a probabilistic space by using the networks outputs. However, this probabilistic hough space based on single frame is easily disturbed. In the third step, a filtering process is employed to smooth the probabilistic hough space by using sequential information. Pose information provided by IMU is applied to align hough spaces extracted at different times to each other. The final hough space is used to eliminate line segments with low possibility and output those with high confidence as the result. Experiments demonstrate that the proposed approach has achieved a good performance.

This paper proposes a new non-radial biennial Luenberger energy and environmental performance index (EEPI) to measure the EEP change in various Chinese cities. The sources of EEP change, in terms of technical efficiency change and technological change, are examined by Luenberger EEPI. The contributions from specific undesirable outputs and energy inputs to the EEP change are identified by means of the non-radial efficiency measure. The proposed approach is applied to evaluate the EEP of the industrial sector in 283 cities in China over 2010-2014. Factors influencing the emission abatement potential are investigated by employing geographically weighted regression (GWR) model. We find that 1) changes in EEP can be attributed to technological progress but that technological progress slows down across the study period; 2) the soot emission performance experiences a downtrend among four specific sub-performances in line with the truth that severe haze happened frequently in China; 3) the best performers begin to move from the coastal to inland cities with the less resource consumption and higher ecological equality; 4) cities with the strongest positive effect in regards to pollution intensity on emission abatement potential are located in the areas around the Bohai Gulf, where air pollution is particularly severe.

The formulation used by the most of studies on an elastic torus are either Reissner mixed formulation or Novozhilov's complex-form one, however, for vibration and some displacement boundary related problem of the torus, application of those formulations has encountered great difficulty. It is highly demanded to have a displacement-type formulation for the torus. In this paper, I will simulate some typical problems and free vibration of the torus. The numerical results are verified by both finite element analysis and H. Reissner's formulation. My investigations show that both deformation and stress response of an elastic torus are sensitive to the radius ratio, and suggest that the analysis of a torus should be done by using the bending theory of a shell, and also reveal that the inner torus is stronger than outer torus due to the property of their Gaussian curvature. Regarding the free vibration of the torus, our analysis indicates that both initial in u and w direction must be included otherwise will cause big errors in eigenfrequency.

Hemangioblasts give rise to endothelial progenitor cells (EPCs), which also express the cell surface markers CD133 and C-kit. They may differentiate into the outgrowth endothelial cells (OECs) that control neovascularization in the developing embryo. Reduced levels of EPC in circulation have been linked to human cardiovascular disorders, according to numerous studies. Furthermore, preeclampsia and senescence have been linked to levels of EPCs produced from cord blood. Uncertainties surround how preeclampsia affects the way EPCs function. It is reasonable to speculate that preeclampsia may have an impact on the function of fetal EPCs during the in utero period; however, given the present literature's suggestion that maternal vasculopathies, including preeclampsia, damage fetal circulation. Additionally, the differentiation potential and general activity of EPCs may serve as an indicator of the health of the fetal vascular system since they promote neovascularization and repair during pregnancy. Thus, the purpose of this review is to compare, through assessment of their quantity, differentiation potency, angiogenic activity, and senescence, the angiogenic function of fetal EPCs obtained from cord blood for normal and pregnancy problems. This will shed light on the relationship between the angiogenic function of fetal EPCs and pregnancy complications, which could have an effect on the management of long-term health issues like metabolic and cardiovascular disorders in offspring with abnormal vasculature development.

Nowadays, with smartphones people can easily take photos, post photos to any social networks and use the photos for some purposes. This leads to a social problem that unintended appearance in photos may threaten the privacy of photographed person. Some solutions to protect facial privacy in photos have already been proposed. However, most of them rely on different techniques to de-identify photos which can be done only by photographers, giving no choice to photographed person. To deal with that, we propose an approach that allows photographed person to proactively detect whether someone is intentionally/unintentionally trying to take pictures of him/her. Thereby, he/she can have appropriate reaction to protect the privacy. In this approach, we assume that the photographed person uses a wearable camera to record the surrounding environment in real-time. The skeleton information of likely photographers who are captured in the monitoring video is then extracted to be put into the calculation of dynamic programming score which is eventually compared with a threshold for recognition of photo-taking behavior. Experimental results demonstrate that by using the proposed approach, the photo-taking behavior is precisely recognized with high accuracy of 92.5%.

The catenary shells of revolution are widely used in constructions due to their unique mechanics' feature. However, no publications on this type of shells can be found in the literature. To have a better understanding of the deformation and stress of the catenary shells of revolution, we formulate the principal radii for two kinds of catenary shells of revolution and their displacement type governing equations. Numerical simulations are carried out based on both Reissner-Meissner mixed formulations and displacement formulations. Our investigations show that both deformation and stress response of elastic catenary shells of revolution are sensitive to its geometric parameter $c$, and reveal that the mechanics of the catenary shells of revolution does much better than the spherical shells. Two complete codes in Maple are provided.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

This paper is devoted to the analysis of fluctuations in the solar wind plasma and interplanetary magnetic field parameters observed by Solar Orbiter and WIND spacecraft at different scales, ranging from ~10^3 to 10^7 km. We investigated two long observation intervals when the spacecraft were near the Sun-Earth line, during which the distance between the spacecraft was 0.1 and 0.5 AU respectively. It is analyzed how the fluctuation properties in different types of SW, associated with quasi-stationary and transient solar phenomena, transform on the way from the Sun to the Earth. It is shown that the time series behavior of the bulk speed subject to the least change even at the large distance between the observation points, while the time series of the IMF magnitude, components and proton density were significantly transformed even at the relatively short distance. Regardless of the assumed change in the absolute value of the parameters, the conducted statistical analysis shows that the characteristics of their fluctuations (including the level of intermittency) remains near constant regardless of the distance between the observation points and depends mostly on the type of the solar wind.

More than twenty-five years ago the Global Solar UV index (UVI) has been introduced as a simple means of visualizing the intensity of ultraviolet radiation and to alert people to the need for sun protection. In our survey among directors of 436 kindergartens in southern Germany we investigated the level of awareness and knowledge about the UVI as well as the practical consequences for sun protection in kindergartens. Less than half of the directors (n=208, 47.7%) had ever heard of the UVI, and only a small minority of them (n=34, 8.7%) used the daily UVI information to adapt sun protective measures in their kindergartens. Detailed knowledge about the UVI was a rarity among the respondents. The proportion of respondents with self-perceived detailed UVI knowledge was five times higher than actual knowledge assessed by an in-depth structured interview using open-ended questions about the UVI (14.2% vs. 2.8%). No clear relationship of UVI awareness, knowledge, and use to directors' age and gender was found. The UVI-related variables also showed no association with directors' knowledge of risk factors for skin cancer and their attitudes towards tanned skin. Overall, the results paint a sobering picture regarding the penetration of the UVI into sun protection policies of German kindergartens. Future public health campaigns should target increasing awareness and understanding of the UVI as well as its importance for sun protection of children.

The formulation used by most of the studies on an elastic torus are either Reissner mixed formulation or Novozhilov's complex-form one, however, for vibration and some displacement boundary related problem of a torus, those formulations face a great challenge. It is highly demanded to have a displacement-type formulation for the torus. In this paper, I will carry on my previous work [ B.H. Sun, Closed-form solution of axisymmetric slender elastic toroidal shells. J. of Engineering Mechanics, 136 (2010) 1281-1288.], and with the help of my own maple code, I am able to simulate some typical problems and free vibration of the torus. The numerical results are verified by both finite element analysis and H. Reissner's formulation. My investigations show that both deformation and stress response of an elastic torus are sensitive to the radius ratio, and suggest that the analysis of a torus should be done by using the bending theory of a shell, and also reveal that the inner torus is stronger than outer torus due to the property of their Gaussian curvature. Regarding the free vibration of a torus, our analysis indicates that both initial in u and w direction must be included otherwise will cause big errors in eigenfrequency. One of the most intestine discovery is that the crowns of a torus are the turning point of the Gaussian curvature at the crown where the mechanics' response of inner and outer torus is almost separated.

Inspired by amazing result obtained by Semay [1], this study revisits generalised Kepler's third law of an n-body system from the perspective of dimension analysis. To be compatible with Semay's quantum n-body result, this letter reports a conjecture which had not be included in author's early publication [2] but formulated in the author's research memo. The new conjecture for quantum N-body system is proposed as follows: Tq|Eq|^3/2 = πG/√2[(Σ^N_i=1 Σ^N_j=i+1 m_im_j)³/(Σ^N_k=1 m_k)]^1/2. This formulae is, of course, consistent with the Kepler's third law of 2-body system, and exact same as Semay's quantum result for identical bodies.

The purpose of this study was to assess the extent to which self-esteem and depression mediated the influence of internalized stigma on life satisfaction among Korean out-of-school youths. Cross-sectional data on 318 youths provided information on perceived stigma, self-esteem, depression, life satisfaction, and personal characteristics. A multinomial logistic regression analysis was followed by structured path analysis to investigate the mediation effects. Internalized stigma was negatively associated with life satisfaction. Self-esteem significantly mediated the influence of stigma on depression and the influence of depression on life satisfaction. Further, stigma directly and significantly influenced depression. This study demonstrated that self-esteem and depression were important to the relationship between internalized stigma and life satisfaction. Implications for possible policies and programs with the aim of helping out-of-school youths to integrate and lead successful satisfying lives are discussed.

To extend the calculation power of tensor analysis, we introduce four new definition of tensor calculations. Some useful tensor identities have been proved. We demonstrate the application of the tensor identities in continuum mechanics: momentum conservation law and deformation superposition.

Zucchini (Cucurbita pepo L.) is an important crash crop for producing seeds in Inner Mongolia, China. In August 2021, the harvest season of seed-producing zucchini, fruit rot symptom (cv. Jindi No.1) was found in the Wuyuan region. The incidence of infected fruits of zucchini ranged from 10% to 30% and symptom consisted in 4 to 5 cm diameter lesions where the fruit was in contact with the soil. Ten isolations from six symptomatic fruits were preliminary classified as Fusarium species based on its morphological characters in potato dextrose agar. Phylogenetic tree was constructed by concatenating TEF-1α and RPB2 gene and exhibited the isolates clustered together with the Fusarium solani f. sp. cucurbitae sequences. Pathogenicity tests revealed that two isolates caused over 3 cm diameter lesions on the fruits while negative-controls remained asymptomatic. The colonies reisolated from the leasions were morphologically identical to the original isolates, thus fulfilling Koch’s postulates. Results demonstrated that F. solani f. sp. cucurbitae was the causal agent of fruit rot observed in the field. To our knowledge, this is the first report of fruit rot of seed-producing zucchini caused by F. solani f. sp. cucurbitae in Inner Mongolia, China.

Among the best-known capillarity phenomena is a capillary rise, the understanding of which is essential in fluidics. Some capillary flows rise monotonically whereas others oscillate, but until now no criteria have been formulated for this scenario. In this paper, the Levine's capillary rise modelling is computed numerically, then the critical radius of the capillary tube is formulated by using the dimensional method and data fitting for identification of exponent index. The phase space diagram of capillary velocity versus height is obtained for the first time and shows that the phase transition from oscillating to monotonic rising happens when the phase trajectory decreases exponentially to somewhere other than the "attractor." Two general Maple codes of the problem are provided as an essential part of this paper.

With the introduction of HTTP/3, whose transport is no longer the traditional TCP protocol but the novel QUIC protocol, research for solutions to the unfairness of Adaptive Streaming over HTTP (HAS) has become more challenging. That is, because of different transport layers, the HTTP/3 may not be available for some networks and the clients have to use HTTP/2 for their HAS applications instead. Therefore, the scenario that HAS over HTTP/3 (HAS/3) compete against HTTP/2 (HAS/2) must be considered seriously. However, there have been a shortage of investigations on the performance and the origin of the unfairness in such a cross-protocol scenario in order to produce proper solutions. Therefore, this paper provides a performance evaluation and root-cause analysis of the cross-protocol unfairness between HAS/3 and HAS/2. It is concluded that, due to differences in the congestion control mechanisms of QUIC and TCP, HAS/3 clients obtain larger congestion windows, thus requesting higher video bitrates than HAS/2. As the problem lies in the transport layer, existing client-side ABR-based solutions for the unfairness from the application layer may perform suboptimally for the cross-protocol case.

As the largest carbon pool on Earth, forest ecosystems are essential to maintaining carbon sink balance. However, accurately estimating the carbon sequestration and carbon storage of forest resources remains an urgent issue to address. Plot investigation, model estimation, and machine learning are examples of current approaches. Nevertheless, because of variables such as regional characteristics and plot size, large-scale and extensive region estimates are comparatively scarce. This study, which focuses on Tianzhu County, aims to comprehensively analyze and estimate the Net Primary Productivity (NPP), carbon storage, and carbon density of the forest ecosystem in this area by integrating data from forest resource inventory and the CASA model. The main conclusions are as follows: (1) The main vegetation types in Tianzhu County include coniferous forests, broad-leaved forests, mixed forests, and shrub forests; (2) Accordin g to the CASA model calculations, the annual cumulative NPP in Tianzhu County in 2020 ranges from a maximum of 249.63 gC/m² to a minimum of 3.40 gC/m², with the forest NPP amounting to 134,674.65 tons of carbon. Based on MODIS observation data, the forest’s NPP is 171,728.32 tons of carbon, with a maximum of 325.36 gC/m² and a minimum of 0.02 gC/m²; (3) At the pixel scale, the carbon storage of forests in Tianzhu County is 361,700 tons. Specifically, 46,500 tons of carbon are stored in coniferous forests, 1,100 tons in broad-leaved forests, 500 tons in mixed forests, and 313,600 tons in shrub forests.

Classical laws of friction suggest that friction force is proportional to the normal load and independent of the nominal contact area. As a great improvement in this subject, it is now widely accepted that friction force is proportional to the real area in contact, and much work has been conducted based on this hypothesis. In present study, this hypothesis will be carefully revisited by measuring the friction force and real contact area in-site and real-time at both normal loading and unloading stages. Our experiments reveal that the linear relation always holds between friction force and normal load. However, for the relation between friction force and real contact area, the linearity holds only at the loading stage while fails at the unloading stage. This study may improve our understanding of the origin of friction.

The hospital indoor environment plays a significant role in shaping the microbial exposures that humans encounter. Resistance to antibiotics is one of the mechanisms employed by bacteria to develop resilience against stress in indoor environments. The extensive usage of antibiotics has been a key factor in driving changes in the ecological function of antibiotic resistance genes (ARGs) and their acquisition by pathogenic bacteria. By integrating the 16S rRNA Illumina sequencing and high throughput-qPCR approaches with water and air dust samples across seven departments at Peking University Shenzhen Hospital, China, this study yielded intriguing findings regarding the department-specific variation, transmission, and correlation of bacteria, ARGs and MGEs within the hospital indoor environment. One notable observation was that the seasonal variation played a vital role in shaping the bacterial composition in the overall hospital indoor environment across seven studied departments. Nevertheless, a similar significant seasonal impact was only observed in the blood test room and emergency departments, rather than in the other five departments. Another intriguing finding was the correlation between ARGs and MGEs abundance. This correlation was evident in the overall hospital indoor environment, which was conversely not found in the emergency, pneumology and gynecology departments. Additionally, while there was no significant relationship that occurred between bacterial communities and ARGs/MGEs within the hospital, the gynecology department demonstrated a close link between bacterial communities and the presence of ARGs/MGEs. Notably, the gynecology department also stood out as an important source of bacteria and ARGs/MGEs for other departments. This study underscores the need for careful surveillance and monitoring of antibiotic resistance, particularly in Legionella spp. in man-made water systems. The findings also show the importance of monitoring and understanding the genetic elements such as Tp614 involved in gene transfer and recombination, as well as their impact on antimicrobial treatment efficacy.

Rotary tillage is a main management tillage practices and widely applied in the North China Plain. However, the long term rotary tillage (depth of 20 cm) results in soil compaction and plow pan formation, which reduces water use efficiency and nutrient uptake, and then impedes the yield increase. In this study, a 3-year field experiment was conducted to investigate the influence of different depths of tillage on soil bulk density, field capacity, water use, photosynthetic rate, nutrients and maize yields in the North China Plain. Three depths of tillage (D20, depth of 20 cm; D25, depth of 25 cm; D30, depth of 30 cm) were assessed. D25 and D30 significantly reduced soil bulk density and improved field capacity in 10-20 and 20-30 cm soil layer, compared to D20. Soil water consumption for D25 was significantly higher 10.12% and 6.61% than that for D20 and D30, respectively. Photosynthetic rate for D25 significantly improved than that for D20 and D30. Total nitrogen in 0-20cm soil layer decreased with the depths of tillage. The maize yields for D25 significantly increased by 20.92% and 21.56% compared to that for D20 and D30, respectively. Structural equation models showed that the total effects of tillage, total nitrogen, photosynthesis and soil water consumption on yields were 0.019, -0.628, 0.121, and 0.895 (path coefficients λ), respectively. The results demonstrated that D25 could improve maize yields, water use efficiency, photosynthetic rate by improving soil water consumption. Depth of 25 cm is optimal tillage practice for the maize production in the North China Plain.

Influenced by geological, climatic, and natural weathering factors, the Great Wall heritage is sus-ceptible to deformations, posing significant challenges to the comprehensive preservation of the Great Wall sites. To investigate techniques for monitoring deformations in extensive linear cultural heritage sites, such as the Great Wall, this study utilizes the SBAS-InSAR technique for deformation monitoring and analysis. A dataset comprising 161 Sentinel-1A images spanning from March 2017 to January 2022 was chosen for SBAS-InSAR processing, yielding a deformation velocity field. To verify result credibility, a typical mountainous segment spanning approximately 896.53 km within the Great Wall landscape corridor underwent analysis. The findings suggest that around 75.8% of the landscape corridor along the Shanxi section of the Ming Great Wall maintain relative stability, displaying deformation rates varying from -10 to 10 mm/year. The remaining 24.2% of the land-scape corridor experiences notable deformations, including a maximum subsidence rate of 33.1 mm/year and a maximum subsidence of 148.6 mm. This study illustrates the potential utility of the SBAS-InSAR technique for monitoring and evaluating surface deformations in extensive linear cultural heritage sites.

The osteoarthritis (OA), the main cause of disability, is a chronic condition that most frequently affects older adults. As the population ages, the cost of treatment is placing pressure on the healthcare budget. As a result, it is imperative to evaluate the medicines' cost-effectiveness and the influence they have on health resource allocation. Hence, our study aims to summarize the cost and outcome of utilizing glucosamine in OA treatment. Authentic databases like Medline, Cochrane, and Scopus were adopted for the identification process up until July 2023. Our primary inclusion criteria centered on the economic evaluation of Glucosamine in OA treatments with provided the incremental cost-effectiveness ratio (ICER) at least. The Quality of Health Economic Studies (QHES) instrument was applied to grade the quality of the studies. A total of 7 qualified studies were selected and discussed the cost-effectiveness of glucosamine with or without other formulations. All of them demonstrated that glucosamine was cost-effective. There was an in-creasement of QALY when incorporating Glucosamine into conventional care. Moreover, Crystalline Glucosamine Sulfate (pCGS) was more cost-effective than the Other Formulations of Glucosamine (OFG). In overall, utilizing pCGS was more beneficial than OFG in terms both of cost and quality of life.

This study presents a tri-layer broadband metamaterial absorber which operates in the GHz range. The absorber was composed of a polyhedral iron-cobalt alloy/graphite nanosheet material arranged in a flat sheet with two punched-in rings for the top layer, a continuous FR-4 layer at the middle, and a continuous copper layer at the bottom. For the normal incidence of electromagnetic wave, the proposed absorber demonstrated an exceptional broadband absorption in a frequency range of 7.9-14.6 GHz, revealing an absorption exceeding 90%. The absorption magnitude remains to be above 90% in a frequency range of 8-11.1 GHz for transverse-electric-polarized waves at incident angles up to 55°. For both transverse-magnetic- and electric-polarized waves, the absorption exceeds 90% in a frequency range of 9.5-14.6 GHz. The physical mechanism behind the absorption properties is analyzed thoroughly through the electric- and magnetic-field distributions. The obtained results could contribute potentially to the development of microwave applications based on metamaterial absorbers, such as radar-stealth technology, electromagnetic shielding for health safety and reduced electromagnetic interferences for high-performance communications and electronic devices.

In order to overcome the limitation of the traditional adaptive Unscented Kalman Filtering (UKF) algorithm in noise covariance estimation for statement and measurement, we propose a hybrid adaptive UKF algorithm based on combining Maximum a posteriori (MAP) criterion and Maximum likelihood (ML) criterion, in this paper. First, to prevent the actual noise covariance deviating from the true value which can lead to the state estimation error and arouse the filtering divergence, a real-time covariance matrices estimation algorithm based on hybrid MAP and ML is proposed for obtaining the statement and measurement noises covariance, respectively; and then, a balance equation the two kinds of covariance matrix is structured in this proposed to minimize the statement estimation error. Compared with the UFK based MAP and based ML, the proposed algorithm provides better convergence and stability.

This study investigates the application of Unmanned Aerial Vehicles (UAVs) equipped with a Micasense RedEdge-MX multispectral camera for the estimation of Secchi Depth (SD) in inland water bodies. The research analyzed and compared five sun-glint correction methodologies — Hedley, Goodman, Lyzenga, Joyce, and threshold removed glint to model the SD values derived from UAV multispectral imagery, highlighting the role of reflectance accuracy and algorithmic precision in SD modeling. While Goodman's method showed a higher correlation (0.92) with in situ SD measurements, Hedley's method exhibited the smallest average deviation (0.65 m), suggesting its potential in water resource management, environmental monitoring, and ecological modeling. The study also underscored the Quasi-Analytical Algorithm (QAA) potential in estimating SD due to its flexibility to process data from various sensors without requiring in situ measurements, offering scalability for large-scale water quality surveys. The accuracy of SD measures, calculated using QAA, was related to variability in water constituents of coloured dissolved organic matter and the solar zenith angle. A practical workflow for SD acquisition using UAVs and multispectral data was proposed for monitoring inland water bodies.

The Sun is a frame at relative rest in which sunlight travels at the emitted speed c. Earth travels at the revolving speed v in this frame. The reflection of light as a mechanical phenomenon applies to the modified Michelson interferometer employed by Miller in his experiments with light from the Sun. Unlike the Tomaschek experiments, which use light from stars that may travel in the Universe at velocities different from that of the Sun, the fringe shifts in the Miller experiments are predictable. Based on Michelson's derivation, Miller expected in his experiments at Mount Wilson a 1.12 fringe shift and observed a fringe shift of 0.08 in 1921 and 0.088 in 1925. The reflection of light as a mechanical phenomenon predicts zero fringe shift for Miller's experiment agreeing only with his observations at the Cleveland laboratory in 1924.

In order to study the crystallinity of different density polyethylenes, the experimental study on the transformation of the conductance mechanism under high electric field was carried out. The X-ray Diffraction(XRD), Different Scanning Calorimeter(DSC), Direct Current(DC) breakdown of Low-density polyethylene(LDPE), Linear low density polyethylene(LLDPE), Medium density polyethylene(MDPE) and High-density polyethylene(HDPE) and the electric field of 5-200kV/mm were tested. Conductivity characteristics experiments, in addition, using the mathematical formula of a variety of conductance mechanisms, the electric field-current density curves of the four kinds of polyethylene were fitted to analyze the conductance transition of the above four kinds of polyethylene in non-ohmic regions under different high field strengths. mechanism. The experimental results show that as the density of polyethylene increases, the crystallinity increases continuously, and the continuous increase of crystallinity causes the electric conduction flow under the same field strength to decrease significantly. The field strength corresponding to the two turning points in the conductance characteristic curve increases simultaneously. Large, the breakdown field strength increases; through analysis, it is found that in the high field, as the electric field increases, the conductance mechanism develops from the ohmic conductance of the low field strength region to the bulk effect of the high field strength region (Poole-Frenkel). Then the electrode effect to the high field strength (Schottky), and the threshold field strength of this conductance mechanism transition increases with the increase of crystallinity.

An undescribed diterpene, stellerterpenoid A (1) and two undescribed sesquiterpenoids, stellerterpenoids B and C (2-3), together with six known compounds, were isolated from the roots of Stellera chamaejasme L. Their structures were elucidated by extensive spectroscopic data (1D, 2D NMR, IR, UV and HR-ESI-MS). The absolute configuration of 1-3 were elucidated based on ECD calculation. Among of them, stellerterpenoid A was a rare 13, 14 - seco nortigliane diterpenoid and stellerterpenoid B was a guaiacane type sesquiterpenoid with an unusual 1, 2-diketone moiety. The known stelleraguaianone B (5) exhibited moderate activity to suppress NO production in LPS - simulated macrophages with an IC50 value of 24.76 ± 0.4 μM. None of the compounds showed inhibitory influenza virus and tumor activity.

We report on space-selective crystallization of congruent and polar Sr2TiSi2O8 crystals in a stoichiometric SrO-TiO2-SiO2 glass induced by (1030 nm, 300 fs) femtosecond laser irradiation. This allows us to compare with non-congruent laser induced crystallization of polar LiNbO3, in non stoichiometric Li2O-Nb2O5-SiO2 glass and gain information on the mechanism of nanocrystals orientation with the laser polarization that we pointed out previously. Using scanning electron microscopy (SEM), Second-harmonic generation (SHG) and electron backscattered diffraction (EBSD), we studied the laser induced crystallization according to the laser processing parameters (pulse energy, pulse repetition rate, scanning speed). We found 1) a domain where the laser track is filled with crystals not perfectly textured (low energy), 2) a domain where an amorphous volume remain surrounded by a crystallized shell (high energy). This arises from Sr out-diffusion and may gives rise to crystallization of both SrTiO3 and Sr2TiSi2O8 phases at low speed. In the one-phase domain (at higher speed), it is found the possibility to elaborate a tube with a perfect fresnoite texture. Significant difference in size and morphology whereas crystallization threshold remains similar are discussed based on glases thermal propeties. Contrarily to Li2O-Nb2O5-SiO2 (LNS) glass, no domain of oriented nanocrystallization controlled by the laser polarization has been found in SrO-TiO2-SiO2 (STS) glass, which is attributed to the larger crystallization speed in STS glass. No nanogratings have also been found that is likely due to the congruency of the glass.

Background: Excessive sun exposure, together with insufficient protection, is the main risk factor for the onset of Melanoma and Non Melanoma skin cancer, namely the most common cancer in fair-skinned populations across the world, and of several other skin and eye adverse health effects. Epidemiological data show the existence of scant awareness of this risk, and of high rates of sunburn among young people. The main aim of the present study is to examine sun exposure habits and protection behaviour in university students. Methods: We performed a cross-sectional questionnaire-based study to investigate sun exposure and protection practices in a group of education sciences students at a university in southern Spain. This survey provided data for a descriptive and comparative analysis, by groups and gender, of photoprotection and skin self-examination practices. The reliability and validity of the questionnaire have been analysed. Results: The questionnaire was completed by 315 students. Most of them (74.6%) have suffered at least one sunburn in the last year. The use of sunscreen or protective clothing is not frequent, and 89.5% of students do not self-examine their skin. The metric properties of the questionnaire showed high values of reliability and validity. Conclusions: The awareness of solar exposure risk in Spanish university students of Education Sciences is low, self-protection is scant, the potential exposure to dangerous levels of UV radiation is high and most students have suffered one or more sunburns in the last year. Intervention strategies should be introduced in these students to highlight the risks involved and the need of more adequate sun protection practices. Information campaigns should be conducted to address the problem so that, when these students become teachers, they have an adequate knowledge of the risk and of the benefits of a higher attention to this problem, and can translate these competences in health education.

The 2020 revision of South Korea’s Personal Information Protection Act (PIPA) updated procedures for the use of medical data for research. The PIPA provision allowing “pseudonymized information” to be used without the consent of the data subject for scientific research introduced ambiguity regarding the applicability of the PIPA versus the Bioethics and Safety Act (BSA), which allows “anonymized information” to be used for research only after data-subject consent and IRB approval for human-subject research are obtained. The main points requiring clarification include the distinction between “human-subject” and “scientific” research, the definition of anonymization and pseudonymization, the requirements for data-subject consent, and the procedures for institutional review boards (IRBs) and data review boards (DRBs). After reviewing the legal concepts and processes, this article recommends clarification of the guidelines for the use of medical data in research by distinguishing the concept and, in the long run, categorizing medical data based on the degree of risk.

Flexible and stretchable conductive materials have received significant attention in several applications such as flexible displays and sensors. In this paper, we report a highly dispersed porous Ag nanoflakes with clean surfaces were fabricated through an explosive growth process. The evolution process from silver nanoflakes to nanomeshes occurred by the novel “dissolution–recrystallization” solvothermal process. The as-obtained Ag meshes have the dual nature of nanoflakes and nanoparticles, which could create an intercross and interpenetration conductive network structures between silver and polymer in the printed elastic conductor, therefore, the silver meshes as conductive fillers used in elastic conductor simultaneously exhibit high conductivity and mechanical durability.

Temporal downscaling of gridded geophysical data is essential for improving climate models, weather forecasting, and environmental assessments. However, existing methods often could not accurately capture multi-scale temporal features, affecting their accuracy and reliability. To address this issue, we introduce an Enhanced Residual U-Net architecture for temporal downscaling. The architecture, which incorporates residual blocks, allows for deeper network structures without the risk of overfitting or vanishing gradients, thus capturing more complex temporal dependencies. The U-Net design inherently could capture multi-scale features, making it ideal for simulating various temporal dynamics. Moreover, we implement a flow regularization technique with advection loss to ensure that the model adheres to physical laws governing geophysical fields. Our experimental results across various variables within the ERA5 dataset demonstrate an improvement in downscaling accuracy, outperforming other methods.

The narrow parking space will result in difficulties in path planning and spot turning caused by sudden changes and discontinuities in path curvature. To address the problem, this paper investigates the performance of three path planning algorithms and proposes a path optimization algorithm. First, the narrow parking space is defined based on single-step parking of the arc-line combination parking algorithm. Second, to compare the arc-line combination algorithm, Hybrid A* algorithm, and particle swarm optimization parking algorithm under different narrow parking spaces, a multi-objective evaluation function is proposed, including three evaluation indicators, namely, the path length, the number of positive and negative conversions of vehicle speed, and the smoothness of the path. Their performance is compared by simulation conducted in MATLAB, the results show that the Hybrid A* algorithm is the better than others for narrow parking spaces. Third, to smooth the planning path, a path optimization algorithm based on the cubic B-spline curve and gradient descent is proposed. Finally, the simulation is conducted between the proposed algorithm and Hybrid A* algorithm, the result shows that the proposal can effectively eliminate the curvature mutation point and constrain the path curvature to meet the requirements of a smooth path.

The vibration propagates in a media such as a shaft in the form of elastic waves. The propagation characteristics of the waves are affected by the geometry of the media, the material properties as well as the cracks. The study to elastic waves propagating in a shaft with transverse cracks can help to detect them. The transverse crack possesses different crack modes due to different external loads. The influence of the crack mode, the location and the depth to the propagation characteristics is investigated in this paper. Firstly, the local flexibility coefficients with three different modes are deduced. And then, the transfer matrix of the elastic wave can be obtained. Finally, the influence of the crack mode, the location and the depth of the transverse crack as well as the rotating speed to the propagation characteristics is then studied, both in a numerical and an experimental way. It’s found that mode III is the most suitable mode in this paper, the location of the crack will make the stopbands fluctuating, the depth mainly affects the bandwidth of the stopbands, and the increase of the rotating speed will shift up the stopbands without changing their bandwidths.

A fast algorithm is established to transform points of the unit sphere into fundamental region symmetrically. With the resulting algorithm, a flexible form of invariant mappings is achieved to generate aesthetic patterns with symmetries of the regular polyhedra. This method avoids the order restriction of symmetry groups, which can be similarly extended to treat regular polytopes in n-dimensional space for n>=4.

The independence of commercial law and the independence of commercial trial are the key issues in the development of China's market economy, which is of great significance for maintaining the market order and protecting the rights and interests of consumers. With the development of China's market economy, the independence of commercial law and commercial trial has gradually become the focus of social attention. On the one hand, the independence of commercial law refers to the effective distinction between commercial law as a normative system and other laws, which has an independent social and economic basis and a unique role. On the other hand, the independence of commercial trial means that commercial trial has relatively independent space and procedures, which can effectively guarantee the fair settlement of commercial disputes.The independence of commercial law is reflected in many aspects, including commercial law ontology, normative structure and content, external relations and so on. Commercial law has the independent social and economic foundation and the unique role, and is the foundation of the development of market economy. The basic principles, adjustment objects, and system design of commercial law are independent, which makes commercial law play its unique role in social life. There are differences between commercial laws and other laws, such as civil law and economic law, in essence and in expression form, which makes commercial law irreplaceable.