The aim of this study is to evaluate the optimal conditions of membrane filtration process. Both laboratory test and pilot-scale test were conducted to examine a treated water on blending water. The water sample were prepared by blending a raw water and the effluent water filtered through an organic membrane. The optimal efficiency in the treatment of water quality at the lab-scale test was generated under conditions of flux at 2.0 m³/m²∙day, the blending ratio of 4:1, and the optimal dosage of coagulant at 20 ppm. The pilot-scale test resulted in that the optimal efficiency was obtained under conditions of flux at 2.0 m³/m²∙day and the blending ratio of 6.0:1. However, the different results between lab-scale and pilot-scale tests on the optimal dosage of coagulant implied that it is difficult to achieve the stable condition of process operation at the low level of coagulant. In summary, the results indicated that, in the combination process of organic membrane and ceramic membrane, the recovery efficiency was achieved above the level of 98.4 %. Compared to 92.1 % in a single organic membrane process, the combination process is 6.3 % more efficient than the single one. This combination process of water treatment lead to stable recovery rates by the optimal input of dosage, less pollution load to water, and a stabilized filtration system.

Background and Objectives: The novel double-pigtail catheter (DPC) has an additional pigtail coiling at the mid-shaft with centripetal multiple side holes. The aim of the present study was to investigate the advantages and efficacy of DPC in overcoming the complications of conventional single-pigtail catheters (SPC) used to drain pleural effusion. Materials and Methods: Between July 2018 and December 2019, 382 pleural effusion drainage procedures were reviewed retrospectively (DPC, n = 156; SPC without multiple side holes, n = 110; SPC with multiple side holes [SPC+M], n = 116). All patients showed shifting pleural effusion in the decubitus view of chest radiography. All catheters were 10.2 Fr in diameter. One interventional radiologist performed all procedures and used the same anchoring technique. Complications (dysfunctional retraction, complete dislodgement, blockage, and atraumatic pneumothorax) were compared among the catheters using chi-square and Fisher’s exact tests. Clinical success was defined as improvement in pleural effusion within 3 days without additional procedures. A survival analysis was performed for calculating the indwelling time. Results: The dysfunctional retraction rate of DPC was significantly lower than that of the other catheters (p < .001). Complete dislodgement did not occur in any of the DPC cases. The clinical success rate of DPC (90.1%) was the highest. The estimated indwelling times were nine (95% confidence interval [CI]: 7.3–10.7), eight (95% CI: 6.6–9.4), and seven (95% CI: 6.3–7.7) days for SPC, SPC+M, and DPC, respectively, with DPC showing a significant difference (p < .05). Conclusions: DPC had a lower dysfunctional retraction rate compared to conventional drainage catheters. Furthermore, DPC were efficient for pleural effusion drainage with a shorter indwelling time.

This paper examines the moral community thesis in the secular context of China. Using multilevel logistic regression, we test (1) whether both individual- (measured by affiliation with institutional religion) and aggregate-level religiosity (measured by the number of religious sites per 10,000 people in province) are inversely related to law and rule violations at the individual level and (2) whether the province-level religiosity enhances the inverse relationship between individual religiosity and the deviant behaviors. Results from analyzing data from the 2010 China General Social Survey and the Spatial Explorer of Religions show that both individual- and aggregate-level religiosity are inversely related to the odds of violating the law and various rules of government, transportation, workplace, and other organizations. However, the cross-level interactions are not significant across models, indicating that the contextual religiosity does not increase the effect of individual-level religiosity on deviance. Implications of findings for the moral community thesis are discussed.

Workplace bullying is a prevalent issue with a significant impact on employees’ mental health. This study aimed to explore the relationship between workplace bullying and the prevalence of depression with a particular focus on the role of gender. A total of 12,344 Korean employees aged 19–65 years were included in the study. They completed questionnaires including the Korean version of the Occupational Stress Scale, the Oldenburg Burnout Inventory, and the Center for Epidemiologic Studies Depression Scale (CES-D). A score of 16 or higher in CES-D indicated depression. The association between workplace bullying and depression was analyzed using logistic regression analyses. The average CES-D scores were higher for both male and female employees who experienced bullying than for those who did not (p &lt; 0.001). The association between the experience of workplace bullying and the prevalence of depression was statistically significant for both genders, with a stronger correlation observed among male employees (p for interaction &lt;0.001). Organizations are urged to address workplace bullying, particularly for male employees, through the implementation of anti-bullying strategies and policies, as well as the provision of mental health resources and support.

In this study, a tuned mass damper is proposed as a seismic acceleration mitigating technique of an electrical cabinet inside the nuclear power plant. In order to know the mitigation performance, the electrical cabinet and the tuned mass damper were modeled using SAP2000. The sine sweep wave was used to confirm the vibration characteristics of the cabinet over a wide frequency range, and the several various earthquakes were applied to the cabinet to verify the control performance of the tuned mass damper. After analyzing the numerical results, it is summarized that the application of the proposed technique can reduce the acceleration response of the cabinet.

Lately, the Critical Pathway(CP) of Electronic Medical Record(EMR) is used to the guideline for a treatment in the public hospital. We propose a healthcare promotion service using disease pattern with lifestyle risk factors. We classify a medical historical patient data with disease codes with lifestyle risk factors (hypertension, diabetes, smoking, overweight, excessive alcohol intake, and low physical activity) to make the lifestyle risk factors through the classification. We finally make the clusters of disease code with lifestyle risk factors using the medical historical data based on EMR's electronic discharge summary data. As the result of that, we do a healthcare recommending service based on the disease pattern with lifestyle risk. We can build a medical help desk of a public hospital to support people as we check into the public hospital; how to get the procedure of curing, the desired curing clinical method for the healthcare promotion service by each disease code, and how to be better our healthcare. We evaluate the performance of the proposed system by experimenting with the datasets collected at the medical center to measure performance and report some experimental results.

In this study, we aimed to identify blood lymphocytes as a prognostic factor for survival in patients with locally advanced stage III non-small cell lung cancer (NSCLC) treated with concurrent chemoradiotherapy (CCRT). We conducted a secondary analysis of 196 patients enrolled in the Korean Radiation Oncology Group 0903 phase III clinical trial to evaluate the prognostic significance of circulating blood lymphocyte levels. The median total lymphocyte count (TLC) reduction ratio during CCRT was 0.74 (range: 0.29 – 0.97). In multivariate analysis, patient age (p = 0.014) and gross tumor volume (GTV, p = 0.031) were significant factors associated with overall survival, while TLC reduction (p = 0.018) and pretreatment neutrophil-to-lymphocyte ratio (NLR; p = 0.010) were associated with progression-free survival (PFS). In multivariate logistic regression analysis, pretreatment NLR, GTV, and heart V20 were significantly associated with TLC reduction. TLC reduction during CCRT is a significant prognostic factor for PFS, and heart V20 is significantly associated with TLC reduction. Thus, constraining the volume of the radiation dose to the whole heart must be prioritized to reduce TLC.

Background: Autonomic neuropathy commonly arises as a long-term complication in end stage kidney disease (ESKD) and can be diagnosed from heart rate variability (HRV), calculated from electrocardiogram (ECG) recordings. There is limited data about HRV using real-time ECG to predict HD efficiency in patients with ESKD who are routinely doing HD in real-world practice. Methods: Total of 50 patients (62.1 ± 10.7 years) with ESKD underwent continuous real-time ECG monitor (237.4 ± 15.3 min) during HD for HRV using remote monitoring system and checked electrolyte levels before/after HD. And we compared HRV according to electrolyte levels. Results: During the monitor, we checked total 2374 times of ECG and electrolyte level simultaneously of all patients. Both time and frequency domain HRV were higher when the patients had lower K+ level (&lt;0.5 mEq/L) and P+ level change (&lt;2 mEq/L) before/after HD as compared with those with higher K+ level (≥0.5 mEq/L) and P+ level (≥2 mEq/L) change respectively. In addition, there were higher incidence of arrhythmic events including atrial/ventricular premature complexes, even though no difference of mean heart rate in patients with lower K+ and P+ level change group (p &lt; 0.001). Conclusions: Higher HRV was independently associated with poor controlled K+ and P+ level during hemodialysis in patients with ESKD. This is further substantiated by independent continuous associations between real-time measures of higher HRV and K+ and P+ level. These data strongly suggest that cardiac autonomic dysfunction can be caused by lower change of electrolytes before/after hemodialysis alone.

The modeling of flood-induced bend scour near embankment toes can provide important information for river engineering, embankment safety warnings, and emergency action management. During the rainy seasons, short-term general scour and bend scour are the most common causes for the failure of reinforced concrete embankments in Taiwan. To gain a deeper understanding of the scouring process near levee foundations, this study proposed a straightforward and practical method for bend scour simulation. The proposed simulation method is subdivided into three stages: two-dimensional flow simulation, general scour estimation, and bend scour estimation. A new bend-scour computation equation is proposed and incorporated into a two-dimensional hydraulic finite-volume model for simulating the evolution of bend scour depth around embankment toes. The proposed method is applied to simulate the temporal evolution of bend scouring near the Shuideliaw Embankment on the Cho-Shui River in Taiwan, where serious failure occurred during the June 2012 monsoon. Field data were gathered using the numbered-brick technique at the Shuideliaw Embankment to demonstrate the accuracy of the proposed method. The results of the bend scour simulations compared reasonably well with field measurements, indicating close agreement in terms of water levels and bend scour depths near the Shuideliaw Embankment. The proposed method was found to quickly estimate the maximum short-term general scour and bend scour depths for further enhancement of the safety of the embankment toe.

U-Net, based on a deep convolutional neural network (CNN), has been clinically used to au-to-segment normal organs and potentially target volumes. However, CNNs with local geometric dependencies may limit the accuracy of segmentation. Additionally, the performance of CNNs can vary depending on the selection of network hyper-parameters, which was mitigated by the proposition of nnU-Net. We chose a vision transformer architecture called VT U-Net, which features a self-attention excluding the convolution layer, to overcome the limitations of CNNs by utilizing global geometric information of images. The VT U-Net v.2 became more powerful thanks to the adaptive hyper-parameter optimizer embedded in nnU-Net. However, despite leveraging the benefits of nnU-Net, VT U-Net v.2 still had additional network hyper-parameters that needed to be optimally chosen. Accordingly, among various hyper-parameters, this study attempted to find the optimal combination of the patch size and the embedded dimension regarding the transformer. From the 4-fold cross-validation, the modified VT U-Net v.2 showed the highest average performance for planning target volume (PTV) segmentation among the investigated networks. Though nnU-Net was based on convolution layers, the adaptive hyper-parameter optimizers turned out to enhance the performance. It was also confirmed that network hyper-parameters affected the segmentation accuracy of vision transformers.

This study presents a meta-analysis of studies that investigate the effectiveness of chitosan administration on lifestyle-related disease in murine models. A total of 34 published studies were used to evaluate the effect of chitosan supplementation. The effect sizes for various items after chitosan administration were evaluated using the standardized mean difference. Using Cochran’s Q test, the heterogeneity of effect sizes was assessed, after which a meta-ANOVA and –regression test was conducted to explain the heterogeneity of effect sizes using the mixed-effect model. Publication bias was performed using Egger’s linear regression test. Among the items evaluated, blood triglyceride and HDL-cholesterol showed the highest Q statistics and I2 values, respectively. Other than blood HDL-cholesterol, total cholesterol, and triglyceride in feces, most items evaluated showed a negative effect size with high significance in the fixed- and random-effect model (p<0.0001). In the meta-ANOVA and -regression test, administering chitosan and resistant starch was revealed to be most effective in lowering body weight. In addition, chitosan supplementation proved to be an effective solution for TNF-α inhibition. In conclusion, chitosan has been shown to be somewhat useful in improving symptoms of lifestyle-related disease. Although there are some limitations in the results of this meta-analysis due to the limited number of animal experiments conducted, chitosan administration nevertheless shows promise in enhancing the quality of human life.

The dopamine D3 receptor is an important CNS target for the treatment of a variety of neurological diseases. Selective dopamine D3 receptor antagonists modulate the improvement of psychostimulant addiction and relapse. In this study, five and six featured pharmacophore models of D3R antagonists were generated and evaluated with the post-hoc score combining two survival scores of active and inactive. Among Top 10 models, APRRR215 and AHPRRR104 were chosen based on the coefficient of determination (APRRR215: R2training = 0.80; AHPRRR104: R2training = 0.82) and predictability (APRRR215: Q2test = 0.73, R2predictive = 0.82; AHPRRR104: Q2test = 0.86, R2predictive = 0.74) of their 3D-quantitative structure–activity relationship models. Pharmacophore-based virtual screening of a large compound library from eMolecules (> 3 million compounds) using two optimal models expedited the search process 100-fold speed increase compared to the docking-based screening (HTVS scoring function in Glide) and identified a series of hit compounds having promising novel scaffolds. After the screening, docking scores, as an adjuvant predictor, were added to two fitness scores (from the pharmacophore models) and predicted Ki (from PLSs of the QSAR models) to improve accuracy. Final selection of the most promising hit compounds were also evaluated for CNS-like properties as well as expected D3R antagonism.

We examined the relationship between living alone and the prevalence of depressive symptoms in older Korean widows and assessed the individual contributions of health, social ties, and socioeconomic factors to the development of depressive symptoms. The study was a secondary analysis using data from widows 65 years of age and older who participated in the Living Profiles of Older People Survey (LPOPS). A logistic regression analysis was used to evaluate the contributions of health, social ties, and socioeconomic factors to the development of depressive symptoms. Working status and equivalent household income were significantly associated with depressive symptoms in both those living with others and those living alone. Adjustment for health status and social ties did not change the impact of living alone on the prevalence of depressive symptoms. However, adjustment for equivalent household income eliminated the negative association between living alone and depressive symptoms. Our findings indicate that economic resources are more important than health and social ties for alleviating the negative impact of living alone on the development of depressive symptoms in older widows.

Visfatin, a member of the adipokine family, plays an important role in many metabolic and stress responses. The mechanisms underlying the direct therapeutic effects of visfatin on wound healing have not been reported yet. In this study, we examined the effects of visfatin on wound healing in vitro and in vivo. Visfatin enhanced the proliferation and migration of human dermal fibroblasts (HDFs) and keratinocytes, and significantly increased the expression of wound healing-related vascular endothelial growth factor (VEGF) in vitro and in vivo. Treatment of HDFs with visfatin induced activation of both extracellular signal-regulated kinases 1 and 2 (ERK1/2) and c-Jun N-terminal kinases 1 and 2 (JNK1/2) in a time-dependent manner. Inhibition of ERK1/2 and JNK1/2 led to a significant decrease in visfatin-induced proliferation and migration of HDFs. Importantly, blocking VEGF with its neutralizing antibodies suppressed the visfatin-induced proliferation and migration of HDFs and human keratinocytes, indicating that visfatin induces the proliferation and migration of HDFs and human keratinocytes via increased VEGF expression. Moreover, visfatin effectively improved wound repair in vivo, which was comparable to the wound healing activity of epidermal growth factor (EGF). Taken together, we demonstrate that visfatin promotes the proliferation and migration of HDFs and human keratinocytes by inducing VEGF expression and can be used as a potential novel therapeutic agent for wound healing.

Plasma plays an important role in semiconductor processes. With the recent miniature and integration, the control of plasma became essential for the success in critical dimension of a few nanometers and etch narrow and deep holes with high aspect ratios. Recently, the etching process has reached physical limitations due to a significant increase in wafer surface temperature under the elevated amount of RF power, affecting not only the warpage phenomenon but also etching uniformity and etching profiles. Therefore, the plasma characteristics are identified using invasive single Langmuir probe (SLP) for wafer temperature diagnosis. Optical data is obtained through a non-invasive optical emission spectroscopy (OES) and the plasma parameters are derived to compare and verify with the SLP. Two variables, electron temperature and electron density, are substituted for the heat flux formula to derive the heat flux according to its location. Using a wafer-type temperature sensor, check the derived heat flux values and compare trends. Such studies are expected to be able to calculate heat flux values in real time, anticipate wafer temperatures, and solve existing problems.

Resection of malignant lesions in the oral and maxillofacial area causes functional and morphological defects. To recover from these defects, reconstruction surgery is needed such as a primary closure or a flap. There are advantages and disadvantages to the method of using the primary closure and the flap, and the choice of procedure is entirely up to a surgeon. The purpose of this study is to evaluate availability of primary closure in patients. For 10 years from January 2010 to May 2020, patients who recovered using flaps after removing malignant lesions from the oral cavity and those who closed the lesion using primary closure were investigated. The investigation was conducted by searching the database of the hospital. There were 85 patients who removed malignant lesions in the oral and maxillofacial area, and among them 16 patients closed the soft tissue defects using primary closure. Operation time, histologic types, stages, wound status, and period of hospitalization according to the patients' medical records were investigated retrospectively. Between the staging and the primary closure, statistically significant differences were observed between stage I and stage II patients in 13 patients using the primary closure. (P=0.046). Statistically significant differences were identified between operation time and primary closure, with an average of 4.02 hours (P=0.015). The average period of hospitality for patients who underwent primary closure was 13.4 days, compared to 26.7 days for those who underwent flap surgery. This difference was statistically significant (P=0.0003). This study evaluated the use of primary closure in patients who underwent resection of malignant lesions in the oral and maxillofacial area. Although the majority of patients underwent reconstruction with flaps, our results showed that primary closure can be a viable option for certain patients with early-stage lesions. Therefore, oral and maxillofacial surgeons should carefully consider various evaluation criteria and select appropriate reconstruction methods to optimize functional and aesthetic outcomes for each patient.

We produced a recombinant eel luteinizing hormone (rec-eel LH) analog with high potency in Chinese hamster ovary DG44 (CHO DG44) cells. The eel LH mutant (LH-M), which had a linker comprising the equine chorionic gonadotropin (eCG) β-subunit carboxyl-terminal peptide (CTP) region (amino acids 115 to149), was inserted between the β-subunit and α-subunit of wild-type tethered eel LH (LH-wt). Monoclonal cells transfected with the eel LH-wt and eel LH-M plasmids were isolated from five and nine clones of CHO DG44 cells, respectively. The secreted quantities abruptly increased on day 3, with peak levels of 5,000–7,500 ng/mL on day 9. The molecular weight of eel LH-wt was 32–36 kDa while that of eel LH-M increased to approximately 38–44 kDa, indicating the detection of two bands. Treatment with peptide N-glycanase F decreased the molecular weight by approximately 8 kDa. The oligosaccharides at the eCG β-subunit O-linked glycosylation sites were appropriately modified post-translation. The EC50 value and maximal responsiveness of eel LH-M increased by approximately 2.90- and 1.29-fold, respectively, indicating that the mutant exhibited more potent biological activity than eel LH-wt. Phosphorylated extracellular regulated kinase (pERK1/2) activation resulted in a sharp peak 5 min after agonist treatment, with a rapid decrease thereafter. These results indicate that the new rec-eel LH analog which contains the eCG β-subunit CTP linker comprising O-linked glycosylation sites, had more potent activity than the wild-type in vitro. Taken together, this new eel LH analog can be produced in large quantities using a stable CHO DG44 cell system.

Obesity and overweight are associated with many metabolic diseases, such as hypertension, diabetes, and dyslipidemia, which are closely related to a sedentary lifestyle and lack of exercise. Aerobic exercise effectively increases the high-density lipoproteins-cholesterol (HDL-C) levels and decreases the triglyceride (TG) levels. The consumption of Cuban policosanol (Raydel®) is also effective in enhancing the HDL-C quantity and HDL functionality to treat dyslipidemia and hypertension. On the other hand, no study has examined the effects of a combination of high-intensity exercise and policosanol consumption in obese subjects to improve metabolic disorders. In the current study, 17 obese subjects (average BMI 30.0±1.1 kg/m2, eight male and nine female) were recruited to participate in a program combining exercise and policosanol (20 mg) consumption for 12 weeks. After completion, their BMI, waist circumference, total fat mass, systolic blood pressure (SBP), and diastolic blood pressure (DBP) decreased by approximately 15% (p=0.022), 12.7% (p=0.008), 33% (p=0.006), 11% (p<0.046), and 13% (p=0.007), respectively. In the serum lipid profile, at week 12, they showed a remarkable decrease in the total cholesterol (TC) and triglyceride (TG) levels, up to 17% (p<0.019) and 54% (p<0.002) from the baseline, respectively. Although the serum HDL-C was increased by approximately +12% from the baseline, the percentage of HDL-C in TC, HDL-C/TC (%), was increased by up to +32% (p=0.007) at week 12. The serum coenzyme Q10 (CoQ10) level was increased 1.2-fold in all participants at week 12 from the baseline. In particular, the male participants showed a 1.4-fold increase (p=0.027) from the baseline. The larger increase in serum CoQ10 was correlated with the larger increase in the serum HDL-C during 12 weeks. The hepatic function parameters were improved; the serum -glutamyl transferase decreased at week 12 by up to 55% (p<0.007), while the aspartate aminotransferase and alanine transaminase levels decreased within the normal range. In the lipoprotein level, the extent of oxidation and glycation were reduced significantly in VLDL and LDL, with a remarkable decrease in the TG content in particles. The antioxidant abilities of HDL2 and HDL3, such as paraoxonase (PON) and ferric ion reduction ability (FRA), were enhanced significantly by up to 1.8-fold (p<0.001) and 1.6-fold (p<0.001) at week 12. The particle size and number of HDL2 were increased up to +10% during the 12 weeks with a remarkable decrease in the TG content, glycation extent, oxidation up to 32% (p=0.032), 18% (p=0.043), and 11% (p=0.023), respectively. The particle number and diameter of HDL3 were increased by up to +9% with a remarkable increase in the PON activity, FRA activity, and TC content of +82% (p<0.001), +56% (p<0.001), and +32% (p=0.009), respectively. Expression of apolipoproteinA-I in HDL2 and HDL3 were significantly elevated more in both gender around 30~48% with more distinct band intensity and less glycation at week 12. These improvements in HDL quality and functionality were linked to the higher survivability of adult zebrafish and their embryos. Under the co-presence of carboxymethyllysine (CML), a microinjection of HDL2 to zebrafish embryo from week 0 resulted in approximately 47% survivability with developmental defects and attenuated speed. On the other hand, the HDL2 microinjection from week 12 resulted in remarkably higher survivability (~ 70%). In conclusion, 12 weeks of Cuban policosanol (Raydel®, 20 mg) consumption with high-intensity exercise showed significant improvement in blood pressure, body fat mass, blood lipid profile without liver damage, CoQ10 metabolism, and renal impairment. At week 12, all participants showed a remarkable decrease in oxidation and glycation extent in the VLDL and LDL with a decrease in the TC and TG content. Significant enhancement of the qualities and functionalities in HDL2 and HDL3 by the policosanol consumption were also detected: increase in apoA-I content, TC content, particle size, and particle numbers along with antioxidant abilities, such as PON and FRA.

In this study, to reduce the use of cement and sand, porous feldspar with excellent economic efficiency was used as a substitute in heat storage concrete layer. When cement was replaced with porous feldspar, the compressive strength was approximately 16%–63% higher compared with when cement was replaced with silicate minerals. To compensate for the reduction in strength owing to the decreased cement content, mechanical and chemical activation methods were employed. When the specific surface area of porous feldspar was increased, the unit weight was reduced by approximately 30% and the compressive strength was increased by up to 90%. When chemical activation was applied using a solidifying agent, the strength was increased by approximately 30% even though 70% of the cement content was replaced with porous feldspar. When cement and sand were replaced with porous feldspar, the compressive strength was approximately two times that of ordinary cement mortar. When the heat storage concrete layer material was replaced with porous feldspar in a pilot scale experiment, the thermal conductivity and heat storage characteristics were better than those of ordinary cement mortar, and an energy-saving effect of approximately 57% was observed, confirming the excellent applicability of porous feldspar as a building material.

Prevention and management of cytomegalovirus (CMV) reactivation is important to improve outcome of allogeneic hematopoietic cell transplantation (allo-HCT) recipients. The aim of this study was to analyze real-world data for incidence and characteristics of CMV infections until 1-year after allo-HCT under 100-day letermovir prophylaxis. A single-center retrospective study was conducted between November 2020 and October 2021. During the study period, 358 patients underwent allo-HCT, 306 of whom received letermovir prophylaxis. Cumulative incidence of clinically significant CMV infection (CS-CMVi) was 11.4%, 31.7%, and 36.9% at 14-weeks, 24-weeks, and 1-year post-HCT, respectively. In multivariate analysis, risk of CS-CMVi increased with graft-versus-host disease (GVHD) ≥ grade 2 (adjusted odds ratio 3.640 [2.036–6.510]; P &lt; 0.001). One-year non-relapse mortality was significantly higher in letermovir breakthrough CS-CMVi patients than those with subclinical CMV reactivation who continued letermovir (P = 0.002). There were 18 (15.9%) refractory CMV infection in this study population. In summary, letermovir prophylaxis is effective in preventing CS-CMVi until day 100, which increased after cessation of letermovir. GVHD is still a significant risk factor in letermovir prophylaxis era. Further research is needed to establish individualized management strategies especially in patients with significant GVHD or letermovir breakthrough CS-CMVi.

Objective: The main purpose of the study is to investigate the combined effects of polydeoxyribonucleotide (PDRN) and extracorporeal shock wave therapy (ESWT) sequences on the regenerative processes in atrophied animal muscles. Methods: Thirty male New Zealand rabbits, aged 12 weeks, were divided into five groups: normal saline, PDRN, ESWT, PDRN injection before ESWT, and PDRN injection after ESWT. Following 2 weeks of cast immobilization, the respective treatments were administered to the atrophied calf muscles. Radial ESWT was performed twice weekly. The evaluation included measurements of calf circumference, tibial nerve compound muscle action potential (CMAP), and gastrocnemius (GCM) muscle thickness after 2 weeks of treatment. Histological and immunohistochemical staining, as well as Western blot analysis, were conducted 2 weeks post-treatment. Staining intensity and extent were assessed using semi-quantitative scores. Results: Groups 4 and 5 demonstrated significantly greater calf muscle circumference, GCM muscle thickness, tibial nerve CMAP, and GCM muscle fiber cross-sectional area (types I, II, and total) than in the remaining three groups (p < 0.05), while they did not did not differ significantly in these parameters. Groups 2 and 3 showed the higher values for all the observations compared to group 1 (p < 0.05). Group 4 had the greatest ratio of vascular endothelial growth factor (VEGF) to platelet endothelial cell adhesion molecule-1 (PECAM-1) in the gastrocnemius muscle fibers than in the other four groups (p < 0.05). Western blot analysis revealed significantly higher expression of angiogenesis cytokines in groups 4 and 5 than in the remaining (p < 0.05). Conclusion: The combination of ESWT and PDRN injection demonstrated superior regenerative efficacy for atrophied calf muscle tissue in rabbit models than these techniques alone or saline. Particularly, administering ESWT after PDRN injection yielded the most favorable outcomes in specific parameters.

The Korean water deer (WD), the dominant wildlife species in South Korea, is classified as vul-nerable on the IUCN Red List. Beside their several unique characteristics, they have a lower in-cidence of tick bites compared to other Cervidae species, particularly roe deer (RD). In natural environments, ticks exhibit questing behavior by waiting on grasses to climb onto host's hair coat. They use sensory organs to detect signals such as body temperature and chemicals from the host's skin, then move to preferred feeding location. Therefore, we conducted a comparative analysis of the skin tissue and hair features of both species to compare the factors leading to lower incidence of tick bites in WD. Notably, WD had significantly larger blood vessels, sebaceous glands, and sweat glands which maintain the barrier functions of the skin (p≤0.004), irregular scale surfaces in hair cuticles, and stiff and 2.83-times thicker primary hair diameter (p<0.001). Each parameters made the ticks difficult to move onto the epidermis of WD. To our knowledge, this is the first report which is focused on the comparative analysis for skin and hair feature in WD and RD. We suggest that these differences may attribute to evade tick bites in WD.

Bacterial communities in rhizosphere and root nodules have significant contributions to the growth and productivity of the soybean (Glycine max L.). In this report, we analyzed the physiological properties and dynamics of bacterial community structure in rhizosphere and root nodules at different growth stages using BioLog EcoPlate and high-throughput sequencing technology, respectively. The BioLog assay found that the metabolic capability of rhizosphere is in increasing trend in the growth of soybeans as compared to the bulk soil. As a result of the Illumina sequencing analysis, the microbial community structure of rhizosphere and root nodules was found to be influenced by the variety and growth stage of the soybean. At the phylum level, Actinobacteria were the most abundant in rhizosphere at all growth stages, followed by Alphaproteobacteria and Acidobacteria and the phylum Bacteroidetes showed the greatest change. But, in the root nodules Alphaproteobacteria were dominant. The results of the OTU analysis exhibited the dominance of Bradyrhizobium during the entire stage of growth, but the ratio of non-rhizobial bacteria showed an increasing trend as the soybean growth progressed. These findings revealed that bacterial community in the rhizosphere and root nodules changed according to both the variety and growth stages of soybean in the field.

Third-generation biomass production utilizing microalgae exhibits sustainable and environmentally friendly attributes, along with significant potential as a source of physiologically active compounds. However, the process of screening and localizing strains that are capable of producing high-value-added substances necessitates a significant amount of effort. In the present study, we have successfully isolated the indigenous marine diatom Odontella aurita OAOSH22 from the East coast of Korea. Subsequently, we conducted a comprehensive analysis of its morphological, molecular, and biochemical characteristics. Afterwards, comprehensive analysis was conducted on the morphological, molecular, and biochemical characteristics, along with testing for optimal growth conditions. The morphological characteristics of the isolate were observed using optical and electron microscopes, and it exhibited typical features of O. aurita. Additionally, the molecular phylogenetic inference derived from the sequence of the small-subunit 18S rDNA confirmed the classification of the microalgal strain as O. aurita. This isolate has been confirmed to contain 7.1 mg g-1 dry cell weight (DCW) of fucoxanthin, a powerful antioxidant substance, in terms of dry cell weight (DCW). In addition, this isolate contains 11.1 mg g-1 DCW of eicosapentaenoic acid (EPA), which is one of the nutritionally essential polyunsaturated fatty acids. Therefore, this indigenous isolate exhibits a significant potential as a valuable source of bioactive substances for various bio-industrial applications.

A flavonoid Astragalin (kaempferol-3-O-β-D-glucopyranoside, Ast) has several biological activities including anti-oxidant, anti-HIV, and anti-allergic effects. Nonetheless, its insolubility in hydrophilic solvents imposes restrictions on its therapeutic applications. In this study, we investigated the effects of water-soluble astragalin-galactoside (kaempferol-3-O- β-D-isomaltotrioside, Ast-Gal) on dendritic cell (DC) maturation and T helper (Th) cell-mediated immune responses. Ast-Gal significantly increased maturation and activation of DCs through up-regulation of surface markers, such as CD80, CD86, and MHC II in a dose-dependent manner, while Ast had little effects. Also, Ast-Gal-treated DCs markedly secreted immune-stimulating cytokines such as IL-1β, IL-6, and IL-12. Importantly, Ast-Gal strongly increased expression of IL-12, a polarizing cytokine of Th1 cells. In a co-culture system of DCs and CD4+ T cells, Ast-Gal-treated DCs preferentially differentiates naïve CD4+ T cells into Th1 cells. The addition of neutralizing IL-12 mAb to cultures of Ast-Gal-treated DCs and CD4+ T cells significantly increased IFN- γ production, thereby indicating that Ast-Gal-stimulated DCs enhance the Th1 response through IL-12 production by DCs. Injection with Ast-Gal-treated DCs in mice increased IFN-γ-secreting Th1 cell population. Collectively, these findings indicate that hydrophilically modified astragalin can enhance Th1-mediated immune responses via DCs, and point to a possible application of water-soluble astragalin-galactoside as an immune adjuvant.

Anesthetic management for pregnant suffering from airway pathology poses unique challenges. The presence of bilateral vocal cord granuloma adds further complexity to the management, as it can potentially cause airway compromise and respiratory distress. This case presents a pregnant patient with bilateral vocal cord granuloma who underwent anesthesia using high-flow nasal cannula (HFNC) oxygenation and oxygen reserve index (ORi) monitoring. A 33-year-old pregnant woman, who had undergone intubation six month ago, experienced hoarseness and was ultimately diagnosed with bilateral granuloma. Due to the significant airway obstruction, neither intubation nor ventilation was feasible, thereby requiring a surgical intervention. Before the surgical removal, the patient’s oxygenation was ensured using HFNC oxygenation. After confirming sufficient oxygenation of the patient with ORi of 0.38, the operation commenced and as it lasted approximately 3 minutes, the patient was able to tolerate the brief period without additional oxygen supply. Post-surgical excision, mask bagging and HFNC oxygenation was resumed, driving ORi to 0.39, then the operation was resumed. Throughout the procedure, SpO2 remained above 98. The combination of HFNC and ORi ensured adequate oxygenation and allowed for early detection of hypoxemia during the procedure. This approach may be a good option for managing granuloma.

Additive manufactured interlocking structures often face challenges in achieving suitable joinability due to thermal deformation. This issue becomes particularly interesting when fabricating structures that require high density but not fully connected layers, such as soft-magnetic materials. This study focuses on systematical investigation of the deformation as a function of finger thickness and building direction in model interlocking structure. In the perpendicular direction to the build plate, the distortions of joint part were significantly reduced due to lower thermal stress. In addition, the effect of laser power and scan speed on interlocking structure are systematically discussed. Additionally, through stress and thermal simulations of additive manufacturing process, it was confirmed that the compensated model can enhance the joinability of interlocking structures. These findings contribute to the development of optimal design for additive manufactured parts of soft magnetic materials such as stators in electric motor components, which needs insulations and density.

Autophagy is a cellular homeostatic process by which cells degrade and recycle their malfunctioned contents, and impairment in this process leads to Parkinson's disease (PD) pathogenesis. Dioscin, a steroidal saponin, has induced autophagy in several cell lines and animal models. The role of dioscin-mediated autophagy in PD remains to be investigated. Therefore, this study aims to investigate the hypothesis that dioscin-regulated autophagy and autophagy-related genes (ATG) could protect neuronal cells in PD via reducing apoptosis and enhancing neurogenesis. In this study, the 1-methyl-4-phenylpyridinium ion (MPP+) were used to induce neurotoxicity and impair autophagic flux in a human neuroblastoma cell line (SH-SY5Y). The result showed that dioscin pre-treatment counters MPP+-mediated autophagic flux impairment and alleviates MPP+-induced apoptosis by downregulating activated caspase-3 and Bax expression while increasing Bcl-2 expression. In addition, dioscin pre-treatment was found to increase neurotrophic factors and tyrosine hydroxylase expression, suggesting that dioscin could ameliorate MPP+-induced degeneration in dopaminergic neurons and benefit the PD model. Interestingly, the neuroprotective activities of dioscin were suppressed when co-treated with chloroquine (CQ), an autophagosome-lysosome inhibitor. In summary, we showed dioscin’s neuroprotective activity in neuronal SH-SY5Y cells might be partly related to its autophagy induction and suppression of the mitochondrial apoptosis pathway.

Eight compounds were isolated from the roots of Glycyrrhiza uralensis and tested for cholinesterase (ChE) and monoamine oxidase (MAO) inhibitory activities. Glycyrol (GC) effectively inhibited butyrylcholinesterase (BChE) and acetylcholinesterase (AChE) with IC50 values of 7.22 and 14.77 µM, respectively, and also moderately inhibited MAO-B (29.48 µM). Six of the other seven compounds only weakly inhibited AChE and BChE, whereas liquiritin apioside moderately inhibited AChE (IC50 = 36.68 µM). Liquiritigenin (LG) potently inhibited MAO-B (IC50 = 0.098 µM) and MAO-A (IC50 = 0.27 µM), and liquiritin, a glycoside of LG, weakly inhibited MAO-B (&gt; 40 µM). GC was a reversible, noncompetitive inhibitor of BChE with a Ki value of 4.47 µM, and LG was a reversible competitive inhibitor of MAO-B with a Ki value of 0.024 µM. Docking simulations showed that the binding affinity of GC for BChE (-7.8 kcal/mol) was greater than its affinity for AChE (-7.1 kcal/mol), and suggested that GC interacted with BChE at Thr284 and Val288 by hydrogen bonds (distances: 2.42 and 1.92 Å, respectively) beyond the ligand binding site of BChE, but that GC did not form hydrogen bond with AChE. The binding affinity of LG for MAO-B (-8.8 kcal/mol) was greater than its affinity for MAO-A (-7.9 kcal/mol). These findings suggest GC and LG should be considered promising compounds for the treatment of Alzheimer’s disease with multi-targeting activities.

Starch content in wheat is an important characteristic for various purposes. Starch is composed of two components known as amylose and amylopectin, and the proportion between these two components plays a crucial role in determining the properties and structure of starch. One of the key genes involved in starch biosynthesis in wheat is granule bound starch synthase I (GBSSI), also known as the waxy protein, which synthesizes amylose in the endosperm. A mutant cultivar, named Gunji-3, was created by crossing the waxy type wheat (Shinmichal 1) with the wild type bread wheat (Keumkang). When comparing the Wx-B1 allele of the waxy protein gene in Gunji-3 with that of the waxy type wheat, there were 12 SNPs and one deletion difference. Additionally, when comparing amino acid sequences with Wx-B1 alleles, differences at two positions are found, indicating that the mutant carries new Wx-B1 allele which is named as Wx-B1o. In terms of the physicochemical properties of Gunji-3 starch, it had a lower amylose content than the parental wheat varieties and showed higher protein content and greater swelling power. These newly introduced waxy type wheat could provide important basis not only for understanding the starch characteristics of wheat but also for various breeding programs.

This study aimed to identify the utility of diffusion-weighted magnetic resonance (MR) imaging with an apparent diffusion coefficient (ADC) map as a predictor of the intrahepatic response of hepatocellular carcinoma (HCC) to cisplatin-based hepatic arterial infusion chemotherapy (HAIC). We retrospectively evaluated 113 consecutive patients with HCC who underwent gadoxetic acid-enhanced and diffusion-weighted MR imaging. The appropriate cutoff for the tumor-to-liver ADC ratio was determined to be 0.741. Of the 113 patients, 51 (45%) presented with a tumor-to-liver ADC ratio < 0.741. Evaluation of the intrahepatic treatment response after 2-3 cycles of HAIC in these 51 patients revealed that 20 patients (39%) experienced an objective response to HAIC. On the other hand, only 10 of the 62 patients with a tumor-to-liver ADC ratio ≥ 0.741 (16%) experienced an objective response. Thus, the objective response rate was significantly higher in patients with a tumor-to-liver ADC ratio < 0.741 than in those with a tumor-to-liver ADC ratio ≥ 0.741 (P = 0.006). Multivariate logistic regression analysis using parameters including perfusion alteration, percentage of a non-enhancing portion, and tumor-to-liver ADC ratio revealed that a tumor-to-liver ADC ratio < 0.741 (odds ratio 3.03; P = 0.015) is the sole predictor of an objective response to HAIC. Overall survival rates were significantly higher in patients with objective responses to HAIC than in those without objective responses (P = 0.001 by log-rank test). In conclusion, patients with unresectable HCC with a tumor-to-liver ADC ratio < 0.741 showed a favorable intrahepatic response to HAIC. Therefore, diffusion-weighted MR imaging can play a critical role as a predictor of response to cisplatin-based HAIC in unresectable HCC.

There is a lack of data comparing sugammadex with anticholinesterase for the quality of anaesthesia recovery, especially following a single bolus dose of rocuronium. Thus, we evaluated the influence of reversal with sugammadex or neostigmine on post-operative quality of recovery by using the Post-operative Quality Recovery Scale (PQRS). A total of 86 patients undergoing trans-pars plana vitrectomy (TPPV) under general anaesthesia were intubated following a single bolus dose of rocuronium (0.6 mg/kg). At the end of surgery, patients were received either neostigmine or sugammadex. The quality of recovery was assessed using the PQRS at 15 minutes and 40 minutes after surgery, and on post-operative day 1. The recovery rate in the physiological domain was higher in the sugammadex group at 15 minutes after surgery (P = 0.02). Though there were no significant differences in the overall cognitive recovery domain, patients in the sugammadex group could recall more numbers in reverse order. However, there were no significant differences between the groups in the other domains of the PQRS. The use of sugammadex may increase the quality of the post-operative physiological recovery at early post-operative periods compared with neostigmine use following a single bolus dose of rocuronium in patients undergoing TPPV with general anaesthesia.

Background: This study aimed to present the development process and characteristics of the Korean Registry of Acute Myocardial Infarction for Regional Cardiocerebrovascular Centers (KRAMI-RCC). Methods: We developed KRAMI-RCC, a web-based registry for patients with AMI. Patients from 14 RCCs were registered for more than 3 years from July 2016. It includes an automatic error-checking system, and user training and on-site monitoring are performed to manage data quality. Results: A total of 11,700 AMI patients were registered in KRAMI-RCC over 3 years (73.9% men). The proportions of patients with ST-elevation and non-ST-elevation myocardial infarction at discharge were 43.4% and 56.6%, respectively. Of the total 3-year patients, 5.6% died in the hospital and 4.4% died 12 months after discharge. The case fatality within 12 months was 9.7%. Prehospital care data showed delayed arrival time after onset of symptoms (median 153 min) and low transportation rate by public ambulance (25.2%). Post-hospital care data showed lower participation rate in the second rehabilitation program (16.8%). Conclusions: The recently developed KRAMI-RCC registry has been more focused on pre-hospital and post-hospital data, which will be helpful in understanding the current state of AMI disease management and in making policy decisions to reduce case fatality in Korea.

Hydrogels incorporated with hydrophobic motifs have received considerable attention to recapitulate the cellular microenvironments, specifically for the bio-mineralization of a 3D matrix. Introduction of hydrophobic motifs into a hydrogel often results in irregular arrangement of the motifs, and further phase separation of hydrophobic domains, but limited efforts have been made to resolve this challenge in the hydrophobically-modified hydrogel. Therefore, this study presents an advanced integrative strategy to incorporate hydrophobic domains regularly in a hydrogel by self-assembling of polymer cross-linkers, building blocks of a hydrogel. Self-assemblies between polymer cross-linkers were examined as micro-domains to incorporate hydrophobic motifs in a hydrogel. The self-assembled structures in a pre-gelled solution were confirmed with the fluorescence analysis and the hydrophobicity of a hydrogel could be tuned by incorporating the motifs in a controlled manner. Overall, the results of this study would greatly serve to tuning performance of a wide array of hydrophobically-modified hydrogels in drug delivery, cell therapies and tissue engineering.

The development of printing technologies has enabled the realization of electric circuit fabrication on flexible substrate. However, the current technique remains restricted to single-layer patterning. In this paper, we demonstrate a fully solution-processable patterning approach for multi-layer circuits using a combined method of laser sintering and ablation. Selective laser sintering of silver (Ag) nanoparticle-based ink is applied to make conductive patterns on a heat-sensitive substrate and insulating layer. The laser beam path and irradiation fluence are controlled to create circuit patterns for flexible electronics. Microvia drilling using femtosecond laser through the polyvinylphenol-film insulating layer by laser ablation, as well as sequential coating of Ag ink and laser sintering, achieves an interlayer interconnection between multi-layer circuits. The dimension of microvia is determined by a sophisticated adjustment of laser focal position and intensity. Based on these methods, the flexible electronic circuit with chip-size-package light-emitting diodes was successfully fabricated and demonstrated with functional operations.

Objective: There are currently no known treatment methods for ensuring complete recovery from facial nerve damage. Thus, various basic and clinical studies continue to be conducted to achieve this end. As part of this research, autophagy is being investigated for its role in nerve regeneration. Here, we review the existing literature regarding the involvement and signifi-cance of autophagy in facial nerve injury and regeneration. Methods: A comprehensive litera-ture review was conducted to assess the induction and role of autophagy in facial nerve injury and subsequent regeneration. Results: Studies conducted on rats and mice have demonstrated activation of autophagy and expression of related factors in facial and sciatic nerves. Among the most studied of these factors in relation to degeneration and regeneration of facial and sciatic nerves are LC3II/I, PI3K, mTOR, Beclin-1, ATG3, ATG5, ATG7, ATG9, and ATG12. Conclusion: This analysis indicates that autophagy is involved in the process of nerve regeneration follow-ing facial and sciatic nerve damage. Inadequate autophagy induction or failure of autophagy re-sponses can result in regeneration issues after facial or sciatic nerve damage. Animal studies suggest that autophagy plays an important role in facial and sciatic nerve degeneration and re-generation.

Background/Aim: microRNAs (miRNAs) are key regulators of both physiological and pathophysiological mechanisms in diabetes and gastrointestinal (GI) dysmotility. Our previous studies have demonstrated the therapeutic potential of miR-10a-5p mimic and miR-10b-5p mimic (miR-10a/b mimics) in rescuing diabetes and GI dysmotility in murine models of diabetes. In this study, we elucidated the safety profile of a long-term treatment with miR-10a/b mimics in diabetic mice. Methods: Male C57BL6 mice were fed a high-fat, high-sucrose diet (HFHSD) to induce diabetes and treated by five subcutaneous injections of miR-10a/b mimics for a 5-month period. We examined the long-term effect of the miRNA mimics on diabetes and GI dysmotility, including an assessment of cancer risk as well as liver and colon inflammation using cancer and inflammatory biomarkers. Results: HFHSD-induced diabetic mice subcutaneously injected with miR-10a/b mimics monthly for 5 months exhibited a marked reduction in fasting blood glucose levels with restoration of insulin and significant weight loss, improved glucose and insulin intolerance, and restored GI transit time. In addition, the miR-10a/b mimic treated diabetic mice showed no indication of risk for cancer development and inflammation induction in the liver, colon, and blood for the 5 months post injections. Conclusion: This longitudinal study demonstrates that miR-10a/b mimics, when subcutaneously administered in diabetic mice, effectively alleviate diabetes and GI dysmotility for 5 months with no discernible risk for cancer or inflammation in the liver and colon. The sustained efficacy and favorable safety profiles position miR-10a/b mimics as promising candidates in miRNA-based therapeutics for diabetes and GI dysmotility.

Cancer treatment is a significant focus in medicine owing to the increasing global incidence. Patients with advanced cancers that do not respond to conventional therapies have limited options and an unfavorable prognosis. Consequently, researchers are investigating complementary approaches to conventional treatments. One such approach is alkalization therapy, which aims to neutralize the acidic tumor microenvironment (TME) by increasing its pH level. The acidic TME promotes inflammation, tumor progression, and drug resistance. Alkalization therapy has been demonstrated to be effective for various cancers. In addition, natural products, such as triterpenoids, parthenolides, fulvic acid, Taxus yunnanensis, and apple pectin have the potential to alleviate symptoms, maintain physical fitness, and improve treatment outcomes of cancer patients through their anti-inflammatory, antioxidant, and anticancer properties. In this review, we focus on the effects of alkalization therapy and natural products on cancer. Furthermore, we present a case series of advanced cancer patients who received alkalization therapy and natural products alongside standard treatments, resulting in long-term survival. We posit that alkalization therapy together with the supplementation of natural products may confer benefits to cancer patients by mitigating the side effects of chemotherapy and complementing standard treatments. However, further research is warranted to validate these clinical findings.

This study aimed to compare the prognosis and characteristics of patients with advanced hepatocellular carcinoma treated with first-line atezolizumab plus bevacizumab (AB) combination therapy and hepatic artery infusion chemotherapy (HAIC). We retrospectively assessed 179 and 72 patients treated with HAIC and AB combination therapy, respectively, between January 2018 and January 2023. The progression-free survival of patients treated with HAIC was significantly superior than that of patients treated with AB (P&lt;0.05), but there was no significant difference in overall survival and objective response rate (ORR) between the two groups (P=0.1056 and P=0.137, respectively). After propensity score matching (PSM), our data revealed that there was no significant difference in PFS between patients who received AB combination therapy and HAIC therapy (P=0.8888). However, patients who received AB combination therapy had significantly better overall survival than those who received HAIC therapy (P=0.0133). In addition, after PSM, significant differences in ORR and disease control rate were not observed. In conclusion, our propensity score study reveals that patients treated with AB therapy have a significantly longer OS than those treated with HAIC.

Extracorporeal membrane oxygenation (ECMO), in conjunction with its life-saving benefits, carries a significant risk of acute brain injury (ABI). Hypoxic-ischemic brain injury (HIBI) is one of the most common types of ABI in ECMO patients. Various risk factors such as history of hypertension, high day 1 lactate level, low pH, cannulation technique, large peri-cannulation PaCO2 drop (∆PaCO2), and early low pulse pressure, have been associated with the development of HIBI in ECMO patients. The pathogenic mechanisms of HIBI in ECMO are complex and multifactorial, attributing to the underlying pathology requiring initiation of ECMO and the risk of HIBI associated with ECMO itself. HIBI is likely to occur in the peri-cannulation or peri-decannulation time secondary to underlying refractory cardiopulmonary failure before or after ECMO. Current therapeutics target pathological mechanisms, cerebral hypoxia and is-chemia, by employing targeted temperature management in the case of extracorporeal cardiopulmonary resuscitation (eCPR), and optimizing cerebral O2 saturations and cerebral perfusion. This review describes the pathophysiology, neuromonitoring, and therapeutic techniques to improve neurological outcomes in ECMO patients so as to prevent and minimize the morbidity of HIBI. Further studies aimed at stand-ardizing the most relevant neuromonitoring techniques, optimizing cerebral perfusion, and minimizing the severity of HIBI once it occurs will improve long-term neurological outcomes in ECMO patients.

Purpose: Therapeutic targeting of RAF1 is promising, but it requires further investigation for the relation between clinical features and RAF1 aberrations regarding the MAPK signaling pathway in various solid tumors to realize the precision medicine. Methods: Between October 2019 and June 2023, Samsung Medical Center, 3,895 patients with metastatic cancer patients received a next-generation sequencing (NGS) using TruSight Oncology 500 (TSO500) assay as a routine clinical practice. We surveyed the incidence of RAF1 aberration including mutation (single-nucleotide variant [SNV]), amplification (copy-number variation), and fusion. Results: In 3,895 metastatic cancer patients, 77 (2.0%) had RAF1 aberrations in their tumor specimen. Of 77 patients, 44 (1.1%) had RAF1 mutations (SNV), 25 (0.6%) had RAF1 amplification and 10 (0.3%) had RAF1 fusions. Among 10 patients with RAF1 fusion, concurrent RAF1 amplification and RAF1 mutation were detected in one patient each. The most common tumor types were bladder cancer (11.5%), followed by ampulla of Vater (AoV) cancer (5.3%), melanoma (3.0%), gallbladder (GB) cancer (2.6%), and gastric cancer (2.3%). Microsatellite instability high (MSI-H) tumors were found in 5 out of 76 patients (6.6%) with RAF1 aberration, while MSI-H tumors were found only in 2.1% of patients with wild-type RAF1 cancer (p < 0.0001). Conclusion: We showed that when patients with metastatic solid cancer receive NGS test, approximately 2.0% have RAF1 aberrations in their tumor specimen.

As lung cancer shows the highest mortality in cancer related death, serum biomarkers are demanded for the lung cancer diagnosis and its treatment. To discover lung cancer protein biomarkers, secreted proteins from primary cultured lung cancer and adjacent normal tissues from patients were subjected to LC/MS-MS proteomic analysis. Quescin sulfhydryl oxidase(QSOX1) was selected as a biomarker candidate from the proteins enriched in the secretion of lung cancer cells. QSOX1levels were higher in 82% (51 of 62 tissues) of lung cancer tissues compared to adjacent normal tissues. Importantly, QSOX1 serum levels were significantly higher in cancer patients (p<0.05, AUC=0.89), when measured by multiple reaction monitoring(MRM). Higher levels of QSOX1 are also uniquely detected in lung cancer tissues among several other solid cancers by immunohistochemistry. QSOX1 knock-downed Lewis lung cancer (LLC) cells was less viable from oxidative stress and had reduced migration and invasion. In addition, LLC mouse models with QSOX1 knock-down also proved that QSOX1 functions in promoting cancer metastasis. In conclusion, QSOX1 might be a lung cancer tissue-derived biomarker and involved in the promotion of lung cancers, and thus can be a therapeutic target for lung cancers.

Infection control among patients is critical for diseases like COVID-19. The concentration of patients in a few facilities burdens healthcare providers and the healthcare system. This study examined the operations of an extended anteroom in a dedicated COVID-19 hospital. It presents issues to consider in the deployment and operation of an extended anteroom through discussions by expert working groups. The subjects covered included efficient space, staffing, equipment management, and education. The process involved wearing personal protective equipment (PPE; in this case, Level D), and if necessary, wearing additional powered air purification respirators (PAPR), after moving from the preparation room to the dressing room, and when entering the hospital through the entrance passage. When leaving the hospital, personnel used a mandatory exit-only passage; in the dressing room, they undressed, and then went outside, in this order. The efficient spatial composition of the anteroom facilitated entry and exit and the separation of contaminated areas and non-contaminated areas using colors and lines. It is necessary to develop operational guidelines for hospitals that treat infectious diseases and conduct research to improve care. The study indicated the need to develop educational programs and use educational simulations to address regionally spread infectious diseases

Synaptopodin 2-like protein (SYNPO2L) is localized in the sarcomere of cardiomyocytes and is involved in heart morphogenesis. However, the molecular function of SYNPO2L in the heart is not fully understood. We investigated the interaction of SYNPO2L with sarcomeric alpha-actinin and actin filaments in cultured mouse cardiomyocytes. Immunofluorescence studies showed that SYNPO2L colocalized with alpha-actinin and actin filaments at the Z-discs of the sarcomere. Recombinant SYNPO2La or SYNPO2Lb caused bundling of actin filaments in the absence of alpha-actinin and enhanced alpha-actinin-dependent formation of actin bundles. In addition, high-speed atomic force microscopy revealed that SYNPO2La directly bound to alpha-actinin via its globular ends. The interaction between alpha-actinin and SYNPO2La stabilized the two proteins on actin filaments. These results strongly suggest that SYNPO2L cooperates with alpha-actinin during actin bundle formation to facilitate sarcomere formation and maintenance.

The common dolphin is the second most bycaught species in Korean waters. To provide key information about their habitat boundaries and hotspots for spatial conservation and management, the spatial use of this species was examined using data obtained from sighting and bycatch surveys of cetacean during the past 20 years. The 95% minimum convex polygon and 95% density contour of fixed kernel suggested that the boundary of home range of common dolphins is limited to the coastal region (Busan-Sokcho) of the East Sea/Sea of Japan. From 50% density contours dawn by kernel density estimation, it was suggested that their hotspots are around the cost of Ulsan-Pohang, Doghae, and Sokcho within the home range. Common dolphins are not at all distributed in the Yellow Sea. Hence, shallow waters, such as the coastal region of the Yellow Sea, are not suitable habitats for common dolphins.

This study aimed to produce single-chain recombinant eel follicle-stimulating hormone (rec-eel FSH) analogs with high activity in Chinese hamster ovary DG44 (CHO DG44) cells. We recently reported that an O-linked glycosylated carboxyl-terminal peptide (CTP) of the equine chorionic gonadotropin (eCG) β-subunit plays contributes on high activity and time-dependent secretion in mammalian cells. We constructed a mutant (FSH-M) in which a linker including the eCG β-subunit CTP region (amino acids 115 to149) was inserted between the β-subunit and α-subunit of wild-type single chain eel FSH (FSH-wt). Plasmids containing eel FSH-wt and eel FSH-M were transfected into CHO DG44 cells. Single cells expressing each protein were isolated from 10 and 7 clones, respectively. Secretion increased gradually during the cultivation period and peaked at 4,000–5,000 ng/mL on day 9. The molecular weight of eel FSH-wt was 34–40 kDa, while that of eel FSH-M increased substantially, with two bands at 39–46 kDa. Treatment with PNGase F to remove the N glycosylation sites decreased the molecular weight remarkably to approximately 8 kDa. The EC50 value and maximal responsiveness of eel FSH-M were approximately 1.23- and 1.06-fold higher than those of eel FSH-wt, indicating that the mutant showed slightly higher biological activity. Phosphorylated extracellular regulated kinase (pERK1/2) activation exhibited a sharp peak at 5 min, followed by a rapid decline. These findings indicate that the new rec-eel FSH molecule with the eCG β-subunit CTP linker showed potent activity and could be produced in massive quantities using the stable CHO DG44 cell system.

Histologically poor differentiation is associated with lymph node metastasis. Thus, pathological evaluation of biopsy specimens is crucial when treating stomach cancers. Deep learning of WSIs is challenging because the images are enormous. Given the computing limitations, patch-level supervised learning methods have been proposed. However, valuable information is lost when dividing WSIs into smaller patches. Another drawback is the need for pixel-level annotation by a pathologist. It is acceptable to differentiate, i.e., grade, gastric cancer at the holistic tissue level (i.e., under low magnification). We developed a weakly supervised learning technique for tissue-level gastric adenocarcinoma histological differentiation (well-to-moderately or poorly differentiated) and applied global reasoning to tissue-level features. The tissue-level AUROCs of the histological differentiation classifiers were 0.953, 0.969, and 0.943, respectively when data from five hospitals were subjected to threefold cross-validation. Comparison of the Grad-CAM heatmaps of the trained classifier and the pathologists’ annotations confirmed that our weakly supervised model exhibited performed well.

Static and dynamic analysis of website security risks is generally used for website security meas-urements. The website security measurements method recently proposed includes similarity hash-based website security risk analysis and machine learning-based website security risk anal-ysis. In this study, a method that can be performed through information disclosed on the Internet was proposed to measure the risk of a website. DNS information, IP information, and website history information are required to measure the risk of a website. In addition, global traffic rank-ing, malicious code distribution history, and HTTP access status can be checked in the website history information. In this study, information related to the security risk of websites in a total of 2,000 domains was collected and analyzed in 1,000 normal and malicious domains. Through the experiment results, 11 open information collection items were selected to measure the security risk of the website. This study presented the possibility of using public information collection to measure website security risk.

The contact materials in high-voltage vacuum interrupter require properties such as high conductivity, high density, and high hardness to minimize arc heat damage. In this study, copper–molybdenum-chromium alloys contact materials are examined for a high voltage contact material. Ball milling process was carried out after analyzing the raw materials of copper, chromium, and molybdenum powders. A green compact was produced using a high press with the mixed powder. Afterwards, composite was produced by sintering method according to temperature and infiltration method according to Cu content in green compact. The composite of sintering method showed a density of 8.55 g/cm3 (relative density 93%) a hardness of 217 HV, and an electrical conductivity of 40.7 IACS% at 1200 °C. The composite of 10 wt.% Cu produced by the Cu infiltration method showed a density of 8.7 g/cm3 (relative density 94%), Hardness of 274HV and electrical conductivity of 39 IACS% at 1300 °C. The measurements of physical properties showed the new possibility of using the Cu–Cr–Mo alloy as a contact material for high-voltage vacuum interrupters.

As symbionts of fungi and algae, lichens produce a variety of secondary products which pharmacological activities. This study aimed to investigate the anti-inflammatory activities of Heterodermia hypoleuca and its main compound, atraric acid. The results confirmed that atraric acid could regulating induced pro-inflammatory cytokine, nitric oxide, induced nitric oxide synthase and cyclooxygenase-2 expression by lipopolysaccharide (LPS)-stimulated RAW264.7 cells. Means while, atraric acid down-regulated expression of phosphorylated IκB, ERK and nuclear factor kappa B (NFκB) signaling pathway to exhibit anti-inflammatory effects in LPS-stimulated RAW264.7 cells. Based on these results, the anti-inflammatory effect of atraric acid during LPS-induced endotoxin shock in a mouse model was confirmed. In the atraric acid treated-group, cytokine production was decreased in the peritoneum and serum, and each organ damaged by LPS-stimulation was recovered. These results show that atraric acid has an anti-inflammatory effect and its molecular mechanism may be involved in the inactivation of the ERK/NFκB signaling pathway, demonstrating its value as a potential therapeutic for inflammatory diseases.

In this paper, we proposed a novel saddle type FinFET (S-FinFET) to effectively solve problems occurring under the capacitor node of dynamic random-access memory (DRAM) cell and showed how its structure was superior to conventional S-FinFETs in terms of short channel effect (SCE), subthreshold slope (SS), and gate-induced drain leakage (GIDL). The proposed FinFET exhibited 4 times lower Ioff than modified S-FinFET called RFinFET with more improved DIBL characteristics while minimizing Ion reduction compared to RFinFET. Our results also confirmed that the proposed device showed improved DIBL and Ioff characteristics as gate channel length decreased.

Extruded polystyrene (XPS) is frequently used in the construction of many different structures. It is therefore necessary to appropriately characterize its mechanical properties to ensure the safety of said structures. Among the available characterization tests, static bending tests are simple and easy to perform; owing to these characteristics, they should be performed more frequently than other tests. However, in static bending tests on XPS, there are several challenges owing to the high flexibility of XPS, and the chosen testing method and sample configuration affect the accuracy of characterization. In this study, three bending properties (Young’s modulus, proportional limit stress, and bending strength) of samples cut from an XPS panel were determined using three-point bending (TPB), four-point bending (FPB), and compression bending (CB) tests with varying sample span/depth ratios, and statistical analyses were performed to determine the relevance of the tests. The experimental results suggest that the TPB and CB tests were more feasible than the FPB test when the span/depth ratio was appropriately determined. However, clear differences were observed in the sample bending properties determined in these tests. In light of these findings, further studies should be conducted to elucidate these differences.

Levels of trace element pollution in surface soil can be estimated using soil analyses and leaching tests. These methods may reveal different results due to the effect of soil properties, such as grain size and mineral composition, on elemental availability. Therefore, this study advocates an alternative method for monitoring and assessment of trace element pollution in surface soil using terricolous fruticose lichens. Lichens growing at abandoned mine sites and unpolluted areas in southwest Japan and their substrata were analyzed using inductively coupled plasma-mass spectrometry and X-ray fluorescence spectrometry to clarify the relationships between Cu, Zn, As, and Pb concentrations in lichens and soils, including their absorption properties. Concentrations of these elements in the lichens were positively correlated with those in the soils regardless of lichen species, location, habitat, or conditions of soils. The analyzed lichens had neither competitive nor antagonistic properties in their elemental absorption, which made them good biomonitors of trace element pollution in surface soil. The distribution maps of average Cu, Zn, As, and Pb concentrations at each sampling region detected almost all of the Cu, Zn, and As pollution of the soils. Therefore, lichens could be used in practical applications to monitor Cu, Zn, and As pollution in surface soils.

VITEK MS PRIME (bioMerieux), a newly developed Matrix-assisted laser desorption ionization time-of-flight mass spectrometry (MALDI-TOF MS) system, alongside VITEK PICKME Pen (PICKME), offers easy sample preparation for bacteria and yeast. VITEK MS PRIME also offers two software platforms for filamentous fungi: the IVD database and the RUO database. Our study evaluated its identification agreement on 320 clinical isolates of bacteria and yeasts, comparing PICKME and traditional wooden toothpick sampling techniques against ASTA Mi-croIDSys Elite results. Additionally, we assessed the IVD (v3.2) and SARAMIS (v4.16) RUO data-bases on 289 filamentous fungi against molecular sequencing. The concordant rates for spe-cies-level identification of bacteria and yeasts were about 89.4% (286/320) between the PICKME and wooden toothpick, about 83.4-85.3% between VITEK MS PRIME and ASTA MicroIDSys Elite. Retesting with PICKME improved concordance to 91.9%. For filamentous fungi, species-level identification reached 71.3% with the IVD database and 85.8% with RUO, which significantly enhanced basidiomycetes' identification from 35.3% to 100%. Some strains in the IVD database, like Aspergillus vesicolor, Exophiala xenobiotica, and Nannizzia gypsea failed to be identified. VITEK MS PRIME with PICKME offers reliable and efficient microorganism identification. For fila-mentous fungi, combining the use of the RUO database can be beneficial, especially for basidi-omycetes.

Background: Early diagnosis of acute brain injury (ABI) is critical for patients on venoarterial extracorporeal membrane oxygenation (VA-ECMO) to guide anticoagulation strategy; however, neurological assessment in ECMO is often limited by patient sedation. Methods: In this pilot study of adults from June 2018 to May 2019, plasma samples of glial fibrillary acidic protein (GFAP), neurofilament light chain (NFL), and Tau were collected daily after VA-ECMO cannulation and measured using a multiplex platform. Primary outcomes were the occurrence of ABI, assessed clinically, and neurologic outcome, assessed by modified Rankin Scale (mRS). Results: Of 20 consented patients (median age=48.5 years; 55% female), 8 (40%) had ABI and 15 (75%) had unfavorable neurologic outcomes at discharge. 10 (50%) patients were centrally cannulated. The median duration on ECMO was 4.5 days (IQR: 2.5-9.5). Peak GFAP, NFL, and Tau levels were higher in patients with ABI vs. without (AUC = 0.77; 0.85; 0.57, respectively) and in patients with unfavorable vs. favorable neurologic outcomes (AUC = 0.64; 0.59; 0.73, respectively). GFAP elevated first, NFL elevated to the highest degree, and Tau showed limited change regardless of ABI. Conclusion: Plasma biomarkers may facilitate early detection of ABIs in VA-ECMO where neurological exam is limited and assist timely clinical decision-making.

Abstract: Cancer survivors are at an increased risk for cardiovascular disease (CVD). However, the association between particulate matter (PM) and CVD risk among cancer survivors (alive >5 years since diagnosis) is unclear. We investigated the risk of CVD among 40,899 cancer survivors within the Korean National Health Insurance Service database. Exposure to PM was determined by assessing yearly average PM levels obtained from the Air Korea database from 2008 to 2011. PMs with sizes <2.5 (PM2.5), <10 (PM10), or 2.5-10 (PM2.5-10) μm in diameter were compared, with each PM level exposure further divided into quintiles. Patients were followed up from January 2012 to date of CVD event, death, or December 2017, whichever came earliest. Adjusted hazard ratios (aHRs) and 95% confidence intervals (CIs) for CVD were calculated using Cox proportional hazards regression by PM exposure levels. Compared with cancer survivors in the lowest quintile of PM2.5 exposure, those within the highest quintile had a greater risk for CVD (aHR 1.31, 95% CI 1.07-1.59). Conversely, increasing PM10 and PM2.5-10 levels were not associated with increased CVD risk (p for trend 0.078 and 0.361, respectively). Cancer survivors who reduce PM2.5 exposure may reduce their risk of developing CVD.

Intrahepatic cholangiocarcinoma (ICCA) is a malignant epithelial neoplasm characterized by biliary differentiation within the liver. ICCA is molecularly heterogeneous and exhibits a broad spectrum of histopathological features. It is a highly aggressive carcinoma with high mortality and poor survival rates. ICCAs are classified into two main subtypes: small duct type and large duct types. These two tumor types have different cell origins and clinicopathological features. ICCAs are characterized by numerous molecular alterations, including mutations in KRAS, TP53, IDH1/2, ARID1A, BAP1, BRAF, SAMD4, and EGFR, and FGFR2 fusion. Two main molecular subtypes–inflammation and proliferation–have been proposed. Recent advances in high-throughput assays using next-generation sequencing have improved our understanding of ICCA pathogenesis and molecular genetics. The diagnosis of ICCA poses a significant challenge for pathologists because of its varied morphologies and phenotypes. Accurate diagnosis of ICCA is essential for effective patient management and prognostic determination. This article provides an updated overview of ICCA pathology, focusing particularly on molecular features, histological subtypes, and diagnostic approaches.

Oscillometric blood pressure (BP) devices currently estimate a single point but do not identify fluctuations in BP or distinguish them from variations in response to physiological properties. In this paper, to analyze BP normality based on oscillometric measurements, we use statistical approaches including kurtosis, skewness, Kolmogorov-Smirnov, and correlation tests. Then, to mitigate uncertainties, we use a deep neural network (DNN) to determine the confidence limits (CLs) of BP measurements based on their normality. The proposed DNN regression model decreases the standard deviation of error (SDE) of the mean error (ME) and the mean absolute error (MAE) and reduces the uncertainty of the CLs and SDEs of the proposed technique. We validate the normality of the distribution of the BP estimation distribution which fits the Gaussian distribution very well. We use a rank test in the DNN regression model to demonstrate the independence of the artificial SBP and DBP estimations. First, we perform statistical tests to verify the normality of the BP measurements for individual subjects. The proposed methodology provides accurate BP estimations and reduces the uncertainties associated with the CLs and SDEs based on the DNN regression estimator.

Although numerous citrus varieties have recently been developed to enhance their quality, information on their quality characteristics is limited. We assessed the quality characteristics of Yellowball, a novel citrus variety, by evaluating its appearance, storability, sensory properties, functionality, and metabolite profiles and comparing these characteristics with those of its parent varieties: Haruka and Kiyomi. The metabolite profiles between the citrus varieties differed significantly, resulting in distinct physicochemical and functional qualities. The storability of Yellowball was significantly increased compared with that of its parent varieties owing to its strong antifungal activity and unique peel morphology, including the stoma and albedo layers. While we did not investigate the volatile compounds, overall functional activities, and detailed characteristics of each metabolite, our data provide valuable insights into the relationship between citrus metabolites, peel morphology, physicochemical properties, and storability and demonstrate the potential of Yellowball as a promising variety in the citrus industry.

Alzheimer’s disease (AD) and type 2 diabetes mellitus (T2DM) are comorbidities that result from the sharing of common genes. The molecular background of comorbidities can provide clues for the development of treatment and management strategies. Here, the common genes involved in the development of the two diseases and in memory and cognitive function are reviewed. Network clustering based on protein-protein interaction networks identified tightly connected gene clusters that have an impact on memory and cognition among the comorbidity genes of AD and T2DM. Genes with functional implications were intensively reviewed, and relevant evidence was summarized. Gene information will be useful in the discovery of biomarkers and the identification of therapeutic targets for AD.

The runtime environment is an important concern for self-adaptive systems (SASs). Although researchers have proposed many approaches for developing SASs that address the issue of uncertain runtime environments, the understanding of these environments varies depending on the objectives, perspectives, and assumptions of the research. Thus, the current understanding of the environment in SAS development is ambiguous and abstract. To make this understanding more concrete, we describe the landscape in this area through a systematic literature review (SLR). We examined 128 primary studies and 14 unique environment models. We investigated concepts of the environment depicted in the primary studies and the proposed environment models based on their ability to aid in understanding. This illustrates the characteristics of the SAS environment, the associated emerging environmental uncertainties, and what is expressed in the existing environment models. This paper makes explicit the implicit understanding about the environment made by the SAS research community and organizes and visualizes them.

The purpose of this study was to assess the extent to which self-esteem and depression mediated the influence of internalized stigma on life satisfaction among Korean out-of-school youths. Cross-sectional data on 318 youths provided information on perceived stigma, self-esteem, depression, life satisfaction, and personal characteristics. A multinomial logistic regression analysis was followed by structured path analysis to investigate the mediation effects. Internalized stigma was negatively associated with life satisfaction. Self-esteem significantly mediated the influence of stigma on depression and the influence of depression on life satisfaction. Further, stigma directly and significantly influenced depression. This study demonstrated that self-esteem and depression were important to the relationship between internalized stigma and life satisfaction. Implications for possible policies and programs with the aim of helping out-of-school youths to integrate and lead successful satisfying lives are discussed.

Recent scholarship highlights the significant environmental impact of the expanding hydraulic fracturing industry, necessitating up-to-date, comprehensive, national-scale assessments. Addressing this gap, this literature review provides a thorough analysis of the contamination and induced seismicity associated with shale-gas hydraulic fracturing in the United States. Employing systematic reviews of literature and federal reports up until July 2023, this study reveals multiple areas of concern. Notably, water and soil contamination, seismic activity, and air pollution are identified as significant challenges linked to shale gas extraction. However, ongoing studies are actively exploring remediation strategies, including advancements in monitoring and treatment technologies, aimed at mitigating the impact of contamination. These findings underscore the need for stringent regulations, continuous research, and effective management practices. This work emphasizes the importance of a collaborative approach that leverages field studies, experimental investigations, and computational advancements to ensure the responsible development of shale gas resources.

We identified a novel heterozygous hypofibrinogenemia, γY278H (Hiroshima). To demonstrate the cause of reduced plasma fibrinogen levels (functional level: 1.12 g/L and antigenic level: 1.16 g/L), we established γY278H fibrinogen-producing Chinese hamster ovary (CHO) cells. An enzyme-linked immunosorbent assay demonstrated that synthesis of γY278H fibrinogen inside CHO cells and secretion into the culture media were not reduced. Then, we established an additional five variant fibrinogen-producing CHO cell lines (γL276P, γT277P, γT277R, γA279D, and γY280C) and performed further investigations. We have already established 33 γ-module variant fibrinogen-producing CHO cell lines including 6 cell lines in this study, but only the γY278H and γT277R cell lines showed disagreement, namely recombinant fibrinogen production was not reduced but the patients’ plasma fibrinogen level was reduced. Finally, we performed fibrinogen degradation assays and demonstrated that the γY278H and γT277R fibrinogens were easily cleaved by plasmin whereas their polymerization in the presence of Ca2+ and “D:D” interaction was normal. In conclusion, our investigation suggested that patient γY278H showed hypofibrinogenemia because γY278H fibrinogen is secreted normally from the patient’s hepatocytes but had accelerated degradation by plasmin in the circulation.

A field experiment was conducted for 2 years in Green Tea Laboratory of Saitama Prefectural Agriculture and Forestry Research Center, Iruma, Saitama, Japan from March 2014 to December 2015. Controlled release fertilizers (CRF) or organic fertilizers (ORG) which is the mixture of chicken manure and oil cakewere applied with the amount of 450 kg N ha^-1 yr^-1 in 2014 and 397 kg N ha^-1 yr^-1 in 2015. Nitrous oxide (N₂O) emissionsfrom soil in green tea fields were measured by closed chamber method. The results showed that CRF has significantly lower N₂O compared to ORG. The cumulative N₂O emissions from CRF accounted for 51% of N₂O emissions from ORG fields and 138% of control with no fertilizer treatment. The N₂O flux from the row was higher than that of under the canopy, since fertilizer were applied on the row. However the total emission from the area between the rows was lower than that under the canopy because of the area ratio of row and canopy was 1:5.

This study presents structural analysis and optimization for the lightweight design of a buoyant rotor-type permanent magnet (BRPM) generator, which was first presented in Bang (2010), and compares its structural performances to a conventional generator with a spoke arm-type rotor and stator. The main benefit of a BRPM is that it can be realized as a bearing-less drive system, free from the mechanical failure of rotor bearings, by using a buoyant rotor. Also, the deformation of a generator by blade vibration can be effectively suppressed using joint couplings between the blades and the rotor. For the design optimization, the objective is set as the mass of the rotor and the stator, and the maximum deformation of the airgap clearance between the rotor and the stator by external forces is constrained below 10% of the gap width. The commercial software Optistruct is used for the analysis and optimization. In this investigation, the analysis and optimization are conducted for a 10 MW wind turbine generator. However, the proposed methods can be extended to larger generator designs without requiring considerable modification. The mass of the opti-mized 10MW BRPM generator is 160.7 tons (19.3 tons for the rotor and 141.4 tons for the stator) while that of an optimized conventional spoke arm-type generator is obtained as 325.6 tons.

Background: Albumin has a pivotal role in the homeostasis of osmotic pressure and is associated with cardiovascular, nephrotic, hepatic, and nutritional diseases. The detection of hypoalbuminemia is a cornerstone for diagnosis of hidden diseases and patient deterioration. We developed and validated a deep-learning-based model (DLM) for detection of hypoalbuminemia using electrocardiography (ECG). Methods: This historical cohort study included data from consecutive patients from two hospitals. The patient data in one hospital were divided into development (82,499 ECGs from 54,248 patients) and internal validation (20,664 ECGs from 20,664 patients) datasets, whereas the patient data in the other hospital were included in only an external validation (37,421 ECGs from 37,421 patients) dataset. An DLM was developed using a 12-lead ECG signal, age, and sex from the development dataset. The endpoint was hypoalbuminemia, defined by serum albumin concentration below 3.5 g/dL. Results: During the internal and external validations, the areas under the receiver operating characteristic curve of the DLM for the detection of hypoalbuminemia were 0.887 (0.877–0.897) and 0.888 (0.880–0.896), respectively. Among the 27,400 individuals without hypoalbuminemia at the initial laboratory exam, those identified by the DLM as higher-risk patients had a significantly larger change in developing hypoalbuminemia than those in the low-risk group (7.09% vs. 1.01%, p < 0.001) during 24 months. The sensitivity map showed that the DLM focused on the T wave and QRS complex for the detection of hypoalbuminemia. Conclusions: The DLM exhibited a high accuracy for hypoalbuminemia detection and prediction using 12-, 6-, and single-lead ECGs.

In this study, we analyzed the microbial community of traditional fermented foods in Jeju Island to identify the distribution of useful microorganisms and confirm their anti-inflammatory and anti-melanogenic effects to determine their potential use as cosmetic ingredients. Firstly, we examined the microbial communities of Omphalius rusticus Jeotgal (OR), Spratelloides gracilis Jeotgal (SG), Chromis notata Jeotgal (CN), Turbo cornutus Jeotgal (TC), Trichiurus lepturus intestine Jeotgal (TL), Branchiostegus japonicus Sweet Rice Punch (BJ), Salted Anchovy Sauce (SA), Jeju Soy Sauce (JSS), and Jeju Soybean Paste (JSP). We found that Latilactobacillus sakei (87.2%), Tetragenococcus halophilus (37.7%), T. halophilus (96.8%), Bacillus subtilis (23.4%), T. halophilus (71.3%), L. sakei (53.7%), Lentibacillus sp. (42.9%), Enterococcus durans (14.6%), and E. durans (32.8%) were the dominant species. Secondly, to study the nine Jeju fermented foods’ anti-inflammatory and anti-melanogenic effects, we employed RAW 264.7 and B16F10 cells, classic cell models for inflammation and melanogenesis studies. Ethyl acetate extracts of the nine Jeju fermented foods all inhibited nitric oxide (NO) and melanin production in a concentration-dependent manner. Thirdly, to test the applicability of the nine Jeju fermented foods to human skin, we used the MTT assay to assess their cytotoxic effects on human keratinocytes (HaCaT cells). Finally, the topical applicability of the nine Jeju fermented foods was tested through primary skin irritation, and it was found that they did not cause any adverse effects. Therefore, extracts from the nine Jeju fermented foods have potential applications as ingredients in anti-inflammatory and anti-melanogenic products and can be used in the cosmetic industry.

A real-time flight simulation tool is proposed using a Virtual Reality Head-Mounted Display (VR-HMD) for airships operating in beyond the line-of-sight (BLOS) conditions. Particularly, the VR-HMD is developed for stratospheric airships flying at low/high altitudes. The proposed flight simulation tool uses the corresponding aerodynamics characteristics of the airship, the buoyancy effect, mass balance, added mass, propulsion contributions and ground reactions in the FlightGear Fight Simulator (FGFS). The VR headset has been connected to the FGFS along with the radio controller containing the real-time orientation/state of each button that is also simulated to provide better situational awareness and a Head-Up Display (HUD) that has been developed to provide the required flight data. In this work, a system was developed to connect the FGFS and the VR-capable graphics engine, Unity, to a PC and a wireless VR-HMD in real-time with minimal lag between data transmission. A balance was found for FGFS to write to a CSV file at a period of 0.01s. For Unity, the file was read every frame which translates to around 0.0167s (60 Hz). A test procedure was also conducted with a similar rating technique based on the NASA TLX questionnaire that identifies the pilot’s spare mental capacity when completing an assigned task to assure the comfortability of the proposed VR-HMD. Accordingly, a comparison has been made for the aircraft control using the desktop simulator and the VR-HMD tool. Results, showed that the current iteration of the system is ideal to train pilots on using similar systems in a safe and immersive environment. Furthermore, such an advanced portable system may even increase the situational awareness of pilots and allow them to complete a sizeable portion of actual flight tests with the same data transmission procedures in simulation. The resulting VR-HMD flight simulator is also conceived to express the ground control station (GCS) concept and transmit flight information as well as the point of view (POV) visuals in real-time using the real environment broadcasted using an onboard camera.

Background: Pathologic complete response (pCR) of breast cancer after neoadjuvant chemotherapy (NAC) is highly related to molecular subtypes. Patients who achieved tumor pCR after NAC have a better prognosis. However, despite of better prognosis, pCR patients have a potential for recurrence. There is little evidence of risk factors of recurrence in patients with pCR. We aim to analyze factors associated with tumor recurrence in patients who achieved pCR. Methods: This study retrospectively reviewed the data of patients diagnosed with breast cancer who achieved pCR after receiving NAC between January 2009 and December 2018 in Samsung Medical Center. pCR was defined as no residual invasive cancer in the breast and axillary nodes even if there is residual ductal carcinoma in situ (ypT0 or ypTis with ypN0). Breast cancers are classified into 4 subtypes based on hormone receptors (HR) and human epithelial growth factor receptor 2 (HER2) status. Patients who had bilateral breast cancer, inflammatory breast cancer, distant metastasis, unknown subtype, and histologically unique case were excluded from the study. Results: In total 483 patients were included in this study except for patients who corresponded to the exclusion criteria. The median follow-up duration was 59.0 months (range, 0.5-153.3 months). Breast cancer recurred in 4.1% of patients (20 of 483). There was a significant difference in clinical T (p = .004) and clinical N (p = .034) stage in the Kaplan-Meier curve for disease-free survival. Molecular subtypes (p = .573), Ki67 (p = 1.000), and breast surgery type (p = .574) were not associated with tumor recurrence in patients who achieved pCR after NAC. In the clinical T stage and clinical N stage, there was a significant difference between recurrence and no-recurrence groups (clinical T stage; p = .045, clinical N stage; p = .002). Univariable Cox regression revealed statistical significance in the clinical T stage (p = .049) and clinical N stage (p = .010), while multivariable Cox regression demonstrated non-significance in the clinical T stage (p = .320) and clinical N stage (p = .073). Conclusion: Results in this study showed that clinical T, clinical N stage, and molecular subtypes were not statistically significant predictors of recurrence in patients who achieved pCR after NAC. It is hypothesized that a multicenter-based study would lead to the identification of factors as predictors of recurrence after achieving pCR.

A systematic approach for model updating using the modal identification results is proposed. Modal identification provides mode shapes for physical quantities (acceleration strain, etc.) measured in specific directions at the location of the sensors. Besides, model updating involves the use of the mode shapes related to the nodal degrees-of-freedom of the finite element analytic model. Consequently, the mode shapes obtained by modal identification and the mode shapes of the model updating process do not coincide even for the same mode. Therefore, a method constructing transform matrices that distinguish the cases where measurement is done by acceleration, velocity and displacement sensors and the case where measurement is done by strain sensors is proposed to remedy such disagreement between the mode shapes. The so-constructed transform matrices are then applied when the mode shape residual is used as objective function or for mode pairing in the model updating process. The feasibility of the proposed approach is verified by means of a numerical example in which the strain or acceleration of a simple beam is measured and a numerical example in which the strain of a bridge is measured. Using the proposed approach, it is possible to model the structure regardless of the position of the sensors and to select the location of the sensors independently from the model.

The geographical environment, food culture, and dietary habits are substantially different between the southern and northern regions in China. We investigated the associations with dietary patterns and metabolic syndrome between Chinese adult from the southern and northern regions (North: 1249; South: 1849) using data from the Chinese Health and Nutrition 2009 survey. Respectively, four dietary patterns were identified by factor analysis in the two regions. Each dietary pattern of factor score was calculated for three groups by tertile (T1<T2<T3). In the northern region, the association between the Alcohol and Western pattern and the risk of abdominal obesity (OR: 1.31; 95%:1.01, 1.68), hypertriglyceridemia (OR: 1.35; 95%:1.05, 1.74), high fasting blood glucose (OR: 1.37; 95%: 1.05, 1.80), and hypertension (OR: 1.55; 95%: 1.45, 1.99) was increased. In the southern region, the Convenience Food pattern was positively associated with hypertriglyceridemia (OR: 1.53; 95%: 1.03, 2.26), low HDL-cholesterol (OR: 1.96; 95%: 1.12, 3.43), and metabolic syndrome (OR: 1.79; 95%: 1.03, 3.11). The Alcohol dietary pattern was positively associated with high fasting blood glucose (OR: 1.83, 95%: 1.13, 2.97). There are some dietary pattern differences in the two regions. It is necessary to consider the factors of food culture and food intake habits in order to provide nutrition education to Chinese individuals from different regions in the future.

Edge computing reduces the response time of real-time services with handling dynamic traffics reliably. Edge servers with limited resources utilize container technology that provides a lightweight execution environment. When deploying containers in edge servers, a container image is required and is downloaded from a remote registry. Therefore, these operations are dependent on network overhead between the container deployment system and the remote registry. Through motivation experiments, we show that container pooling time increases in proportion to physical distance and has characteristics that vary flexibly depending on runtime time. In this study, we define a system model for high-speed registry deployment in this edge system and propose a clustering technique into k groups based on the network overhead and affinity of the regionally distributed edge servers that make up the edge system. Also, considering idle resources, we propose a technique to deploy a registry after electing a leader for each cluster. A simulation experiment is conducted to verify the performance of the proposed technique and shows that performance improvement can be achieved regardless of the number of edge servers and the k value.

(1) Background: Depressional wetlands are highly vulnerable to changes in temperature and rainfall, affecting littoral vegetation, thus HydroGeoMorphic (HGM) wetland types. This study aimed to assess the utility of Sentinel-2A vegetation indices in enhancing delineation and sub-classify depressional HGM types. (2) Methods: We sampled 84 pairs of four vegetation indices from 10x10m plots along 14 belt transects in eight depressional wetlands in Mpumalanga, South Africa. We evaluated vegetation index differences between and within wetlands, focusing on lit-toral gradients. (3) Results: Significant differences (Bonferroni p

Recently, due to the miniaturization of electronic products, printed circuit boards (PCBs) have also become smaller. This trend has led to the need for high-precision electrical test equipment to check PCBs for disconnections and short circuits. The purpose of this study is to improve the position repeatability of the platform unit up to ±2.5 μm in a linear stage type test equipment. For this purpose, the causes of position errors of the platform unit are analyzed. The platform unit holding the PCB is driven by a single-axis linear ball screw drive system offset from its geometric center due to design constraints. The yaw rotation of the platform is found to have a dominant effect on position repeatability. To address this problem, the methods of adding balancing weights to the platform unit and adjusting the stiffness of LM Guides are proposed. This reduces the yaw rotation by moving the centers of mass and stiffness closer to the linear ball screw actuator. In the verification tests, the position repeatability was decreased to less than ±1.0 μm.

The purpose of this study is to develop and evaluate a self-microemulsifying drug delivery system (SMEDDS) to improve the oral absorption of poorly water-soluble Olaparib. Through the solubility test of Olaparib in various oils, surfactants and co-surfactants, pharmaceutical excipients for use in SMEDDS manufacturing were selected. Self-emulsifying regions were identified by mixing the selected materials at various ratios, and a pseudoternary phase diagram was constructed by synthesizing these results. Various physicochemical properties of microemulsion incorporating Olaparib were confirmed by investigating the particle morphology, particle size, zeta potential, drug content and stability. In addition, the improved dissolution and oral absorption of Olaparib were also confirmed through a dissolution test and a pharmacokinetic study. An optimal microemulsion was generated in the formulation of Capmul MCM EP/NF 10%, Labrasol 80% and PEG 400 10%. Fabricated nano-sized microemulsions were well-dispersed in aqueous solutions, and it was also confirmed that it was maintained well without any problems of either physical or chemical stability. The 5 min initial dissolution of Olaparib in fabricated formulations was improved by 10.6 times (pH1.2), 14.8 times (pH6.8) and 14.8 times (distilled water) compared to the values of Olaparib powder. The dissolution at 120min was 45.4±4.0%(pH1.2), 53.5±1.1% (pH6.8) and 58.1±1.00% (distilled water) in Olaparib powder but has been significantly improved by 1.7 times (74.8±1.9%), 1.6 times (84.2±0.3%) and 1.5 times (81.2±0.7%) in SMEDDS. Associated with the high dissolutions of Olaparib in fabricated microemulsions, the pharmacokinetic parameters were also greatly improved. The Cmax and AUCinf of Olaparib in the prepared microemulsion were increased 4.2- and 3.2-fold, respectively, compared to powder. Taken together with the results mentioned above, the microemulsion system could be an effective tool as an oral delivery formulation for Olaparib. Additionally, our results demonstrate that the SMEDDS systems comprising Capmul MCM, Labrasol and PEG 400 could be a useful option for improvement of several other poorly water-soluble drugs with physico-chemical properties similar to Olaparib.

Energy and Environment Tax is used globally as a means of environment policy. Energy and Environment tax plays an important role as a driving force for the conversion to environmentally friendly energy. The basic tax principles considered in the design of energy and environmental taxation increases the efficiency of policy instruments. The purpose of this study is to evaluate South Korea’s energy and environmental taxation based on tax principles, namely, equity, efficiency, simplicity, flexibility, and accountability and to suggest directions for improvement. This study applied a methodology that provides policy implications, such as reviewing existing literature and comparing energy and environmental taxes. Results of this study show that South Korea’s energy and environmental taxation is negative in terms of equity, simplicity, and accountability. South Korea’s current energy and environmental tax is regressive to income classes and complex tax structures and it does not objectively measure the impact of energy and environmental taxation. However, energy and environmental taxation is evaluated positively in terms of efficiency and flexibility because it meets the greenhouse gas reduction policy and operates a flexible tax rate. The results of this analysis provide policy implications for reorganizing South Korea’s energy and environmental taxation

We propose a deep learning algorithm that directly compensates for luminance degradation owing to the deterioration of organic light emitting diode (OLED) devices to address the burn-in phenomenon of OLED displays. Conventional compensation circuits are encumbered by a high cost of development and manufacturing processes owing to their complexity. However, given that deep learning algorithms are typically mounted on a system on chip (SoC), the complexity of the circuit design is reduced, and the circuit can be reused by re-learning only the changed characteristics of the new pixel device. The proposed approach comprises deep feature generation and multi-stream self-attention, which decipher the importance of the variables, and the correlation between burn-in-related variables. It also utilizes a deep neural network that identifies the nonlinear relationship between the extracted features and luminance degradation. Thereafter, the luminance degradation is estimated from the burn-in-related variables, and the burn-in phenomenon can be addressed by compensating for the luminance degradation. The experimental results revealed that compensation was successfully achieved within an error range of 4.56%, and demonstrate the potential of a new approach that can mitigate the burn-in phenomenon by directly compensating for pixel-level luminance deviation.

Objective: The effect of long-term performance of one-bottle or two-bottle bonding agents on the shear bond strength to lithium disilicate ceramics (LDS) were to investigate, and the long-term performance of the bond strength of two-bottle bonding agent (Tokuyama Universal Bond II) was investigated under conditions without hydrofluoric acid solution (abbreviated as HF)-pretreatment of LDS. Methods: Nine resin cements (both self-adhesive and adhesive types) were used. It was investigated 1) the adhesion strength of various resin cements to LDS from the presence or absence of HF-treatment, 2) to determine the effect of the deterioration in three times [after one-day storage (abbreviated as Base), and after 5,000 &amp; 20,000 thermocycles (abbreviated as TC 5k and TC 20k)] of one- and two-component bonding agents. And the difference in degradation between one- and two-component bonding gents consist of the silane coupling agent was performed by chemical analysis (High Performance Liquid Chromatography). Results: The trends of resin cements were statistically not very different for each cement 3 times with HF-conditions. Also ESTECEM II and Super-Bond Universal showed the significant greatest values in two conditions (TC 5k and TC 20k) without HF-condition. In TC 20k, ESTECEM II &amp; Super-Bond Universal showed significantly better results than others when treated with the recommended bonding agents without HF-condition. In TC 20k, there was not much statistically significant difference if pretreated with Tokuyama Universal Bond II without HF-condition. Significance: When using LDS, it was found that long-term durability could be maintained by pretreating with Tokuyama Universal Bond II without pretreating with various hazardous HFs.

As medical care aiming to maintain the quality of life for elderly patients is increases, implant treatment for elderly patients is increasing worldwide. Therefore, we aimed to investigate implant stability and the reliability of different measuring devices according to implant placement site and duration in patients aged over 65 years. The study evaluated 60 implants in 60 patients aged ≥ 65 years. The implant placement sites were divided into six evenly distributed sections (n=10) i.e., maxillary right- posterior, A; maxillary anterior, B; maxillary left-posterior, C; mandibular right-posterior, D; mandibular anterior, E; mandibular left-posterior, F. Participants visited the hospital seven times: preoperatively, 1V; implant surgery, 2V; stitch removal, 3V; 1-month follow-up, 4V; 2-months follow-up, 5V; before final-restoration delivery, 6V; and after final-restoration delivery, 7V. The implant stability was evaluated with the Osstell Mentor (ISQ), Periotest M (PTV), and Anycheck (IST). The mean values of ISQ, PTV, and IST were analyzed (α=.05). ISQ, PTV, and IST results of 5V and 6V were significantly higher than those of 2V (P<.05). The lowest ISQ results occurred in E location at 5V and 6V (P<.05). In all mandibular locations, IST results of 7V were significantly higher than those of 2V, 3V, 4V, and 5V (P<.05). ISQ results were negatively correlated with PTV and positively correlated with IST, and PTV was negatively correlated with IST. By considering various factors that affect implant stability, the appropriate implant load application time was determined. This could help increase the implant success rate in elderly patients. And as a diagnostic device for implant stability for evaluation of osseointegration in elderly patients, Anycheck was also able to prove its relative reliability compared to Osstell ISQ Mentor and Periotest M.

This study aimed to identify the most beneficial attitudes adopted by enterprise participants during their engagement in open-source software (OSS) activities. For this purpose, we selected repositories from GitHub, featuring the top 10 with the highest stars and forks, classified the participants according to their sentiment states, and compared their productivity. The results indicated that participants with positive sentiments were more productive than those with negative sentiments. Consequently, it can be inferred that encouraging organizations to express positive sentiments towards their developers publicly may stimulate OSS community activities and enhance productivity, thereby potentially leading to increased open innovation and sustainability.

This study examined the impact of Vibration-Assisted Drilling (VAD) on hole quality and residual stress in Ti-6Al-4V ELI material. Ti-6Al-4V ELI possesses excellent mechanical properties but presents challenges in machining, including chip evacuation, burr formation, and elevated cutting temperatures. VAD, particularly Low-Frequency Vibration-Assisted Drilling (LF-VAD), has been explored as a potential solution to address these issues. The research com-pares LF-VAD with conventional drilling (CD) under various cutting and cooling conditions. LF-VAD exhibits higher maximum cutting forces under specific conditions, which result in accel-erated tool wear. However, it also demonstrates lower RMS (Root Mean Square) forces com-pared to CD, offering better control over chip formation, reduced burr formation, and improved surface roughness within the hole. Furthermore, LF-VAD generates greater compressive residual stresses on the hole's inner surface compared to CD, suggesting enhanced fatigue performance. These findings indicate that LF-VAD holds promise for improving hole quality, fatigue life, and overall component durability in Ti-6Al-4V machining applications.

Rapeseed (Brassica napus L.) is one of the most oil crop, and its commercial value is contingent upon its agronomic characteristics and oil quality. In this study, 73,226 single nucleotide polymorphisms (SNPs) across 95 rapeseed mutant lines derived from gamma rays and their original cultivar (‘Tamra’) obtained from genotyping-by-sequencing (GBS) was investigated gene ontology (GO) analysis and genome-wide association study (GWAS). GWAS was conducted on agronomic (plant height, ear length, thousand seed weight and seed yield) and oil (fatty acid and crude fat) traits. GO analysis showed that many genes displaying SNPs were involved in cellular processes, intracellular anatomical structures and organic cyclic compound binding. A total of 149 significant SNPs were associated with the agronomic traits (76 SNPs) and oil traits (73 SNPs). Bna.A05p02350D (SFGH) and Bna.C02p22490D (MDN1) were selected as novel candid genes for thousand seed weight. In addition, Bna.C03p14350D (EXO70) and Bna.A09p05630D (PI4Kα1) were selected as novel candidate genes for the erucic acid and crude fat content, respectively. These findings could facilitate the identification of optimal genotypes for breeding new cultivars, and association studies represent an economically efficient tool for mutant screening and the selection of elite rapeseed-breeding lines.

The aim of this study is to investigate transient dynamic flow characteristics of the fluid flow through 5-way electric coolant valve (PCCV : Penta-Control Coolant Valve). To achieve this goal, the present paper attempts the three-dimensional dynamic simulation of the fluid flow through the valve using a commercial CFD solver with moving mesh technique to consider flow inertia and dynamic flow in the opening and closing stages of the ball valve rotating motion. Firstly, dynamic flow characteristics and the thermal mixing inside the PCCV ball valve during the opening and closing stage was analyzed. It is found that the discrepancies between dynamic and steady state simulation is remarkable when fluxes with different levels of enthalpy and momentum flow into the PCCV leads to strong flow interference and flow inertia, while the discrepancies are relatively small at low rotation speed and weak flow interference. Then, the effect of dynamic flow characteristics of the valve on dynamic thermal mixing characteristics at two different ball valve rotational speeds and rotational directions were investigated. It was found that the dynamic flow and thermal mixing characteristics inside the PCCV are greatly affected by the rotation speed, rotation direction, and degree of flow interference between fluxes. It is helpful for the design of the better coolant control strategies and the improvement of the FCEV thermal management system.

In industrial settings, gears play a crucial role by assisting various machinery functions such as speed control, torque manipulation, and altering motion direction.The malfunction or failure of these gear components can have serious repercussions, resulting in production halts and financial losses. As a result, there is an increasing requirement to monitor the state of these components in order to avoid such issues from occurring. To address this need, research efforts have focused on early defect detection in gears in order to reduce the impact of possible failures. This study focused on analyzing vibration and thermal datasets from two extruder machine gearboxes using an autoencoder Long Short-Term Memory (LSTM) model. The major goal is to implement an outlier detection approach to detect and classify defects. The results of this study highlighted the extraordinary performance of the Autoencoder LSTM model, which achieved an impressive accuracy rate of 94.42% in recognizing malfunctioning gearboxes within the extruder machine system. Furthermore, the study used a thorough global metrics evaluation methodology to further test the model’s dependability and efficacy, consequently substantiating the proposed approach’s validity.

Burrs form due to plastic deformation of materials during machining processes, such as milling and drilling. Deburring can be very difficult when the burrs are not easily accessible for removal. In this study, abrasive flow machining (AFM) was adopted for deburring the edges of milling specimens. Based on the experimental observations on AL6061 specimens, the deburring performance was characterized in terms of flow speed, the local curvature of the streamline near the burr edge, and shear stress. A new objective function that can predict the extent of deburring is proposed based on these characteristics and validated through experiments. Based on this new objective function, a prediction of deburring performance on the burr edge of the intersecting holes with offset was performed. The results between the predicted and experimental observation results were in reasonable agreement.

Background In this study, we describe our clinical experience with the fifth-generation of a breast implant with a smooth, fine surface from a Korean manufacturer (BellaGel^Ò SmoothFine; HansBiomed Co. Ltd., Seoul, Korea) in Asian women. Methods We analyzed 223 women (mean age=35.28±9.45 years and mean follow-up period=12.03±2.48 months), comprising 118 bilateral cases and 109 unilateral ones, who received breast augmentation using the BellaGel^Ò SmoothFine at our hospital between June 4, 2018 and February 28, 2019. For safety assessment, we analyzed frequencies of postoperative complications and overall survival of the BellaGel^Ò SmoothFine. Results Postoperatively, complications (12 cases, 5.38%) include asymmetry (3 cases, 1.35%), hematoma (2 cases, 0.90%), hypertrophic scars (2 cases, 0.90%), wound disruption (2 cases, 0.90%), rippling (1 case, 0.45%), capsular contracture (1 case, 0.45%), stretch deformities with skin excess (1 case, 0.45%). In addition, time-to-events were calculated as 10.94±0.64 months (95% CI 9.69-12.19) and the survival rate reached 0.290±0.168 (95% CI 0.094-0.901) at 12 months postoperatively. Conclusions Here, we describe our clinical experience with the BellaGel^Ò SmoothFine. Our results are of significance in that this is the first report about the fifth-generation of a breast implant with a smooth, fine surface from a Korean manufacturer in Asian women.

Although chronic obstructive pulmonary disease (COPD) and interstitial lung disease (ILD) have distinct clinical features, both diseases may coexist in a patient because they share similar risk factors such as smoking, male sex, and old age. Patients with both emphysema in upper lung fields and diffuse ILD are diagnosed with combined pulmonary fibrosis and emphysema (CPFE), which causes substantial clinical deterioration. Patients with CPFE have higher mortality compared with patients who have COPD alone, but results have been inconclusive compared with patients who have idiopathic pulmonary fibrosis (IPF). Poor prognostic factors for CPFE include exacerbation, lung cancer, and pulmonary hypertension. The presence of interstitial lung abnormalities, which may be an early or mild form of ILD, is notable among patients with COPD, and is associated with poor prognosis. Various theories have been proposed regarding the pathophysiology of CPFE. Biomarker analyses have implied that this pathophysiology may be more closely associated with IPF development, rather than COPD or emphysema. Patients with CPFE should be advised to quit smoking and undergo routine lung function tests, and pulmonary rehabilitation may be helpful. Various pharmacologic agents may be beneficial in patients with CPFE, but further studies are needed.

In this study, the literature on varnish contamination is investigated among the various con-taminations of lubricant. As the period of use of lubricant increases, the lubricant deteriorates and becomes contaminated. The varnish causes filter plugging, sticking of hydraulic valves and fuel injection pumps, obstruction of flow, reduction of clearance, poor heater and cooler perfor-mance, and increase of friction and wear in various lubrication systems. These problems also cause mechanical system failure, performance degradation, and increased maintenance and re-pair cost. To improve the problems causes by the varnish, an adequate understanding of varnish is required. Therefore, in this literature review, definitions and characteristics, generating ma-chinery, generating mechanisms, causes, measurement methods, and prevention or removal methods are summarized. Most of the data are reports of companies related to lubricant and machine maintenance, and are included in some papers. We hope that this summary of varnish will be helpful to those who are engaged in reducing or preventing varnish problems.

Although natural products are an important source of drugs and drug leads, identification and validation of their target proteins have proven difficult. Here, we report the development of a systematic strategy for target identification and validation employing drug affinity responsive target stability (DARTS) and mass spectrometry imaging (MSI) without modifying or labeling natural compounds. Through a validation step using curcumin, which targets aminopeptidase N (APN), we successfully standardized the systematic strategy. Using label-free voacangine, an antiangiogenic alkaloid molecule as the model natural compound, DARTS analysis revealed vascular endothelial growth factor receptor 2 (VEGFR2) as a target protein. Voacangine inhibits VEGFR2 kinase activity and its downstream signaling by binding to the kinase domain of VEGFR2, as was revealed by docking simulation. Through cell culture assays, voacangine was found to inhibit the growth of glioblastoma cells expressing high levels of VEGFR2. Specific localization of voacangine to tumor compartments in a glioblastoma xenograft mouse was revealed by MSI analysis. The overlap of histological images with the MSI signals for voacangine was intense in the tumor regions and showed colocalization of voacangine and VEGFR2 in the tumor tissues by immunofluorescence analysis of VEGFR2. The strategy employing DARTS and MSI to identify and validate the targets of a natural compound as demonstrated for voacangine in this study is expected to streamline the general approach of drug discovery and validation using other biomolecules including natural products.

Epoxy was blended with benzoxazine resin and aluminum trihydrate (ATH) additive to render flame retardancy while maintaining mechanical properties. The ATH was modified using three different silane coupling agents and then added to 60/40 epoxy/benzoxazine mixtures. The effect of blend compositions and surface modification on flame retardant and mechanical properties of the composites was investigated by UL94, tensile, and shear tests. Resin mixtures containing more than 40 wt% benzoxazine revealed a UL94 V-1 rating with enhanced tensile and shear strength. Upon addition of 20 wt% ATH to 60/40 epoxy/benzoxazine, a V-0 rating was achieved. The lowered tensile and adhesive properties of the composites in the presence of ATH were improved by modifying the ATH surface using silane coupling agents.

In order to realize the tram's low-floor structure, most of the trams that have been recently introduced adopt an independently rotating wheelset. In the case of trains driving in two regions with different gauges, an independently rotating wheelset may be applied to utilize the variable track technology. Since the independent rotation type wheelset has no rotational restraint of the left and right wheels, the difference in rotational speed between the outer and inner wheels occurs naturally during curved driving, and it is applied to railroad vehicles traveling in steep curve sections because it smoothly drives curved driving. However, the longitudinal creep force and the lateral restoring force are weakened as the left and right rotational constraints disappear. Lack of transverse direction restoring force weakens stability while causing continuous flange contact driving or zigzag phenomenon against disturbance. Under the conditions of driving in a steep curve, these railway vehicles generate excessive wear, noise, and lateral pressure, as well as deterioration of ride comfort and derailment. In order to overcome these drawbacks, a method has been proposed in which the torque of a motor mounted on each wheel is individually controlled to generate lateral restoring force or to improve driving performance through lateral displacement control using a yaw moment. In this paper, development using HILs was performed to check the performance and stability of the individual motor torque control technology before verifying by applying the individual motor torque control to the actual vehicle. HILs were constructed by combining a real-time dynamic analysis model of a railway vehicle with a drive motor to which real individual motor control was applied. Under the conditions of driving the test track where the actual test vehicle was tested, the analysis of the driving characteristics and the control characteristics of the disturbance was performed to confirm the proposed individual motor torque control performance.

Hepatocellular carcinoma (HCC) is currently the third leading cause of malignancy-related mortalities worldwide. Natural killer (NK) cells are involved in the critical role of first line immunological defense against cancer development. Defects in NK cell functions are recognized as important mechanisms for immune evasion of tumor cells. NK cell function appears to be attenuated in HCC, and many previous reports suggested that NK cells play a critical role in controlling HCC, suggesting that boosting the activity of dysfunctional NK cells can enhance tumor cell killing. However, the detailed mechanisms of NK cell dysfunction in tumor microenvironment of HCC remain largely unknown. A better understanding of the mechanisms of NK cell dysfunction in HCC will help in the NK cell-mediated eradication of cancer cells and prolong patient survival. In this review, we describe the various mechanisms underlying NK cell dysfunction in HCC. Further, we summarize current advances in the approaches to enhance endogenous NK cell function and in adoptive NK cell therapies, to cure this difficult-to-treat cancer.

This study aimed to improve sensitivity of ferrous particle sensors used in various mechanical systems such as wind power gearboxes to detect abnormalities by measuring the amount of ferrous wear particles generated by metal-to-metal contact. Existing sensors collect ferrous particles using a permanent magnet. However, its ability to detect abnormalities is limited because it only measures amounts of ferrous particles collected on the top of the sensor. To overcome this limitation, this study evaluated sensibility of an existing sensor using a multi-physics analysis method and improved it by changing the core shape inside the sensor. The detection ability of the improved sensor was analytically shown to be better than the existing sensor. This study highlights the use of analytical methods and multi-physics analysis for developing a ferrous particle sensor and presents a method to compare sensibility analytically. Results of the improved sensor are expected to enhance the ability to detect abnormalities in the lubrication system where ferrous wear particles are generated. This study will contribute to the development of more effective ferrous particle sensors, which can potentially improve the performance and reliability of mechanical systems.

Precise binding affinity predictions are essential for structure-based drug discovery (SBDD). Focal adhesion kinase (FAK) is a member of the tyrosine kinase protein family and is overexpressed in a variety of human malignancies. Inhibition of FAK using small molecules is a promising therapeutic option for several types of cancer. Here, we conducted computational modeling of FAK targeting inhibitors using 3-dimensional structure-activity relationship (3D-QSAR), molecular dynamics (MD), and hybrid topology-based free energy perturbation (FEP) methods. The structure-activity relationship (SAR) studies between the physicochemical descriptors and inhibitory activities of the chemical compounds were performed with reasonable statistical accuracy using CoMFA and CoMSIA. These are two well-known 3D-QSAR methods based on the principle of supervised machine learning (ML). Essential information regarding residue-specific binding interactions was determined using the MD and MM-PB/GBSA methods. Finally, physics-based relative binding free energy (〖∆∆G〗_RBFE^(A→B)) values of analogous ligands were estimated using the alchemical FEP simulation. An acceptable agreement was observed between the experimental and computed relative binding free energies. The overall results using ML and physics-based hybrid approaches could be useful for the rational optimization of accessible lead compounds with similar scaffolds targeting the FAK receptor.

Accurate evaluation of thermo-fluid dynamic characteristics in tank are critically important for designing liquid hydrogen tank of small-scale hydrogen liquefier to minimize heat in-leak into the liquid and ullage. Due to the huge cost, most future liquid hydrogen storage tank designs will have to rely on predictive computational models for storage tank pressurization and heat-leak minimization. Thus, reliable on predictive numerical models to aid design process of tank design have been required. Therefore, in this study, in order to improve the storage efficiency of the small-scale hydrogen liquefier, a three-dimensional CFD model that can predict the boil-off rate and the thermo-fluid characteristics due to heat penetration has been developed. The prediction performance and accuracy of the CFD model is validated on the basis of the comparisons between its results and previous experimental data and a good agreement is obtained. To evaluate insulation performance of polyurethane foam according to thickness, the pressure change and thermo-fluid characteristics in a partially liquid hydrogen tank, subject to fixed ambient temperature and wind velocity, has been investigated numerically. Three different insulation thickness were considered to investigate not only interfacial characteristics between liquid and ullage but thermo-fluid dynamics in hydrogen storage tank for various heat-leak situation. The results indicate that as the insulation thickness becomes thinner and more heat penetration exists, natural convection by buoyancy develops stronger, so strong vortices are created near the interfacial zone by upward flow driven by buoyancy. In particular, as the amount of heat in-leak increased, wider and stronger heat accumulation was found in the top dished head area of the ullage area. In addition, it was confirmed that the CFD model developed in this study could well describe the phenomenon in which the temperature of the tank wall and the insulation mat increased at a faster rate due to faster heat transfer from the vapor and interface. In the future, the numerical model developed in this study will be used for optimizing insulation system of storage tank for small-scale hydrogen which is cost-effective and highly efficient.

Background and Objectives: High rates of psychiatric disorders and comorbidities have been reported in juvenile detainees which have been associated with repeat offenses. However, research on this topic has been limited to Asian countries. This study aimed to examine the prevalence of psychiatric disorders and sexual differences among juvenile detainees in a detention center in South Korea. Materials and Method: The participants comprised 54 males and 46 females, with a minimum intelligence score of 80. Psychiatric diagnosis was determined using the Mini-International Neuropsychiatric Interview for Children and Adolescents (MINI-KID). The Massachusetts Youth Screening Instrument-Version 2 (MAYSI-2) was used to investigate gender differences. Results: Using the MINI-KID, the most frequent diseases were conduct disorder (CD), alcohol dependence, suicidal tendency, attention-deficit/hyperactivity disorder (ADHD) with statistically significant differences between men and women. Only alcohol abuse was higher in men while the rest were higher in women. The items with a statistically significant gender difference in MAYSI-2, were alcohol/drug use, feeling depressed/anxious, somatic complaints, suicidal ideation, and traumatic experience. All items for which the gender difference was statistically significant were higher in the proportion of women. Conclusions: Juvenile detainees exhibit high rates of psychiatric disorders and comorbidities. CDs, alcohol dependence and ADHD are the most common psychiatric disorders among juvenile detainees in South Korea. Assessment of and intervention in psychiatric disorders may help prevent further offenses. These findings highlight the importance of diagnosing and intervening in psychiatric disorders within juvenile detention systems.

Nonsteroidal anti-inflammatory drugs (NSAIDs), which block the activity of cyclooxygenase (COX) isoenzymes and inhibit the synthesis of prostaglandin, have been used for pain relief. We have developed a method to separate a mixture of three NSAIDs, such as aspirin, paracetamol, and naproxen, using reverse-phase high-performance liquid chromatography (RP-HPLC). An isocratic mobile phase consisting of acidic water and acetonitrile was selected to run at a low flow rate, such as 0.8 mL/min. The mixture of three NSAIDs was injected at a low volume into a C18 column that was 150 mm in length and characterized using a UV detector at 230 nm. We identified three peaks in the chromatogram indicating the three compounds. The elution time of the peaks was less than 10 minutes. To identify multiple peaks on the isocratic flow using a short column, further studies are required regarding the proposed method to generate microfluidic devices for nanoLC.

This paper uses the complex regression analysis method to establish the customer’s load regression models, which consider economic indicators, temperature and rainfall. Furthermore, the proposed models are used to study the forecasting feasibility of the future energy sales and summer peak load demand. At first, this paper used least-squares techniques to derive regression models for considering economic indicators and temperature of 34 customer energy sales and total energy sales. Besides, the AMI high voltage customer demand data and system generating capacity for 24 hours were adopted to forecast summer peak load. The above-mentioned data analysis tool is used by EViews software to achieve, in order to verify the feasibility of the research framework. The study found that although its forecasting model accuracy is low only when mixed with temperature and high voltage demands. So, when mixed with high voltage demand data and system generating capacity for 24 hours to forecast peak load, the average error is ± 0.87% and in the majority of its energy sales forecasting model of average error is ±3%. This result can provide power company as future reference.

Currently, maritime traffic is increasing with economic growth in several regions worldwide. However, this growth in maritime traffic has led to increased risk of marine accidents. These accidents have a higher probability of occurring in regions where geographical features, such as islands, are present. Further, the positioning of rescue ships in a particular ocean region with a high level of maritime activity is critical for rescue operations. This paper proposes a method for determining an optimal set of locations for stationing rescue ships in an ocean region with numerous accident sites in the Wando islands of South Korea. The computational challenge in this problem is identified as the positioning of numerous islands of varying sizes located in the region. Thus, the proposed method combines a clustering-based optimization method and an image processing approach that incorporates flood filling to calculate the shortest distance between two points in the ocean that detours around the islands. Experimental results indicate that the proposed method reduces the distance from rescue ships and each accident site by 5.0 km compared to the original rescue ship locations. Thus, rescue time is reduced.