In this study, an experiment was conducted on hoop pine (Araucaria cunninghamii), which is a common tree species in Taiwan. Holes with diameters of 4, 5, 7, 10, 12, and 14 cm were drilled in dry hoop pine timber with a diameter of 39 cm and a height of 57 cm, and an 800 MHz Ground Penetrating Radar (GPR) antenna were used to determine the minimum image resolution and the size of the holes in the wood. GPR images of the timber were subjected to a filtering process to obtain characteristic reflection curves of the damage to the timber. Curves with clear waveforms were observed in the GPR profiles of eccentric holes with a diameter of 4 cm. Profiles of the damage were obtained and profile images with the trunk radius at the centre were transformed into polar coordinate images. From these polar coordinate images, the location, size and diameter of the eccentric holes in the wood were identified, and the reflection curves were characterised by waveforms and irregular fluctuations. The risk levels of tree trunks were determined on the basis of their t/R (minimum normal wall thickness of the cross-section of the trunk/radius of the trunk) values and hole area ratios. A comparison between the GPR-based results and the actual diameters of the holes revealed that the filtered GPR profiles could be used for the efficient and accurate assessment of damage to hoop pine timber (average error rate ≤ 4%).

This paper first discusses a fractional-order Liu system of order as low as 2.7 and shows its chaotic characteristics by carrying out numerical simulations such as Lyapunov exponents, bifurcation diagrams and phase portraits. Then, by using the topological horseshoe theory and computer-assisted proof, the existence of chaos in the system is verified theoretically. Finally, the fractional-order system is implemented on a Field Programmable Gate Array (FPGA) and the results obtained show that the fractional-order Liu system is indeed chaotic.

In this paper we perform numerous numerical studies for the problem of low-rank matrix completion. We compare the Bayesian approaches and a recently introduced de-biased estimator which provides a useful way to build confidence intervals of interest. From a theoretical viewpoint, the de-biased estimator comes with a sharp minimax-optimal rate of estimation error whereas the Bayesian approach reaches this rate with an additional logarithmic factor. Our simulation studies show originally interesting results that the de-biased estimator is just as good as the Bayesian estimators. Moreover, Bayesian approaches are much more stable and can outperform the de-biased estimator in the case of small samples. However, we also find that the length of the confidence intervals revealed by the de-biased estimator for an entry is absolutely shorter than the length of the considered credible interval. These suggest further theoretical studies on the estimation error and the concentration for Bayesian methods as they are being quite limited up to present.

Flood records of the Kunmalik River in Chinese Tien Shan mountains have showed that glacier- dammed lake outburst floods (GLOF) had occurred almost every year since 1956 from the glaci-er-dammed Lake Merzbacher. However, GLOF in cold season is seldomly studied. The defense and management of the flood need further observation and study. The maximum peak discharge of 825 m3/s occurred on 5th December 1996 with the maximum flood volume of 2.875×108 m3, which was 18 times larger than that of the mean daily discharge in winter over the past six decades. The drainage of the Merzbacher lake is not a mechanical breaking up of the glacier dam, but the release of pressurized water along a subglacial tunnel triggered by quickly surge of the Northern Glacier, the subglacial tunnels are enlarged by both ice melting and frictional heat in the flooding water and heat under the glaciated dam and the lake in winter. There is no correlation between the GLOF size and air temperature of cold season. The floods in cold season have become bigger since 1996 than that before, and the flood duration has been extended from winter to spring. Once the cold GLOF starts, its discharge can be forecasted day by day to extrapolate the monitoring hydrograph as a linear curve.

We derive some Quantum Central Limit Theorems for expectation values of macroscopically coarse-grained observables, which are functions of coarse-grained hermitean operators consisting of non-commuting variables. Thanks to the hermicity constraints, we obtain positive-definite dis- tribution for the expectation values of observables. These probability distributions open some pathway for an emergence of classical behaviours in the limit of in nitely large number of identical and non-interacting quantum constituents. This is in contradistinction to other mechanisms of classicality emergence due to environmental decoherence and consistent histories. The probabil- ity distributions so derived also enable us to evaluate the nontrivial time-dependence of certain differential entropies.

Bisphenol A (BPA) has been identified as one of endocrine disrupting chemicals (EDCs). Due to its massive production (over 700,000 tons per year) and the extensive use of BPA-based plastics (i.e., polycarbonate and epoxy resin) in Taiwan, it was thus included into a toxic substance by the Ministry of Environment. This work surveyed the updated information about the production of BPA and its environmental distributions in Taiwan over the past decade. Furthermore, the regulatory strategies and countermeasures for managing the environmental risks of BPA by the Taiwan government were summarized to show the cross-ministerial efforts under the relevant acts, including the Toxic and Concerned Chemical Substances Control Act (TCCSCA), the Food Sanitation Management Act (FSMA) and the Commodity Inspection Act (CIA). The findings showed that most of the monitoring data showed far below the acceptable risks. However, the people may pose an adverse threat to the aquatic environment and human health via ecological and food chains. In addition, some countermeasures were further recommended to echo the international actions on environmental endocrine disruptors in recent years.

The paper presents the prediction of hydrodynamic characteristics of different rudder -plane configurations behind a submarine in deep water through the Reynolds-Averaged Navier-Stokes method in Ansys Fluent Solver. The hydrodynamic force and moment acting on the Cross-plane, X-plane, and Y-plane rudder configurations are analyzed for estimating hydrodynamic coefficientsfor predicting the advantages of each configuration to control the ship. The obtained results show that X-force of the X-plane rudder configuration is larger than the force acting on the Cross-plane rudder and Y-plane rudder configurations. However, Y-force, and Z-force of the X-plane rudder configuration are significantly greater than the Y-force of the left configurations. The same tendency can be seen in the moment of the X-plane rudder about the y-axis and z-axis. The roll moment induced by the Y-plane and Cross-plane rudder configurations is significantly larger than the case of the X-plane rudder configuration.

The recent market and pandemic, with their complex nature and unpredictable developments, have had a great impact on coffee chains. The recovery factor in today's fiercely competitive coffee market is also derived from customer satisfaction, and the product's perceived value and ever with businesses' capabilities and recovery strategies. The research is based on the Customer and Service Recovery Performance model. Therefore, this study aims to investigate the impact of the Customer Satisfaction premise on the service recovery of the coffee chain and some other effects. After collecting surveys from 300 customers who have used beverages at famous coffee chains in Vietnam and performing data analysis via SEM-PLS, the results show that customer satisfaction positively influences customer loyalty. Customer loyalty mediates between customer satisfaction, and price fairness affects the resilience of the coffee chain. In addition, the two factors, Flexibility, and Adoption, also positively affect service recovery performance. Therefore, for coffee chains, customers are an important factor, and they need to maintain customer loyalty. In addition, seek ways to increase flexibility and apply technology at stores so that the company has enough experience and capacity to respond promptly to difficult market conditions, natural disasters and epidemics. This study presents insights into how coffee chains can adapt to the dynamic business environment during the current difficult business environment.

Osteoclasts (OCs) are the multinucleated, bone-resorbing giant cells originally differentiated from a monocyte/macrophage lineage. OC differentiation and maturation, also called osteoclastogenesis, are strictly regulated by a variety of signaling pathways primarily induced by the interactions of two prerequisite cytokines, macrophage colony-stimulating factor (M-CSF) and the receptor activator of nuclear factor-κB ligand (RANKL) to their respective surface receptors, c-fms and RANK, in OC precursors (pre-OCs). Rab11 has emerged as the spatiotemporal regulators of intracellular vesicular transport in the endosomal recycling system; however, how it regulates osteoclastogenesis is incompletely understood. OC-triggered bone resorption is best characterized to be immensely dependent upon lysosomal function, the intracellular acidic organelles containing more than 50 acid hydrolases secreted into bone matrix microenvironment (BME). On the contrary, it is little known about the lysosomal function on modulating the turnover of c-fms and RANK surface receptors via Rab GTPase-mediated vesicular transport, thereby dictating osteoclastogenesis. In this review, I briefly describe the mechanism underlying lysosome-induced osteoclastogenesis via the Rab11-mediated modulation of the surface receptors in OCs.

Concussion, also known as mild traumatic brain injury (mTBI), commonly causes transient neurocognitive symptoms, but in some cases, it causes cognitive impairment, including working memory (WM) deficit, which can be long-lasting and impede a patient’s return to work. The predictors of long-term cognitive outcomes following mTBI remain unclear because abnormality is often absent in structural imaging findings. The purpose of the study was to determine whether machine learning-based models using functional magnetic resonance imaging (fMRI) biomarkers and demographic or neuropsychological measures at baseline could effectively predict 1-year cognitive outcomes of concussion. We conducted a prospective, observational study of patients with mTBI who were compared with demographically-matched healthy controls enrolled between September 2015 to August 2020. Baseline assessments were collected within the first week of injury, and follow-ups were conducted at 6 weeks, 3 months, 6 months, and 1 year. Potential demographic, neuropsychological, and fMRI features were selected according to the significance of correlation with the estimated changes in WM ability. The support vector machine classifier was trained using these potential features and estimated changes in WM between the predefined time periods. Patients demonstrated significant cognitive recovery at the third month, followed by worsened performance after 6 months, which persisted until 1 year after concussion. Approximately half of the patients experienced prolonged cognitive impairment at 1-year follow up. Satisfactory predictions were achieved for patients whose WM function did not recover at 3 months (accuracy=87.5%), 6 months (accuracy=83.3%), 1 year (accuracy=83.3%), and performed worse at 1-year follow-up compared to baseline assessment (accuracy=83.3%). This study demonstrated the feasibility of personalized prediction for long-term postconcussive WM outcomes based on baseline fMRI and demographic features, opening a new avenue for early rehabilitation intervention in selected individuals with possible poor long-term cognitive outcomes.

Due to their excellent physicochemical properties, fluorinated greenhouse gases (F-gases), including hydrofluorocarbons (HFCs), perfluorocarbons (PFCs), sulfur hexafluoride (SF6), and nitrogen trifluoride (NF3), are used in a variety of applications, but they are potent greenhouse gases. Therefore, they have been blanketed into the list of phase-out under the international protocols or treaties. In this work, the updated statistics of the Taiwan’s national inventory report (NIR) were used to analyze the trends of F-gases (i.e., HFCs, PFCs, SF6 and NF3) emissions during the period of 2000-2020. Furthermore, the regulatory strategies and measures for reducing the emissions of the four F-gases will be summarized to be in accordance with the national and international regulations. With the progressive efforts by the regulatory requirements and the industry’s voluntary reduction, the total F-gases emissions indicated a significant increase from 2,462 kilotons of carbon dioxide equivalents (CO2eq) in 2000 to the peak value (i.e., 12,643 kilotons) of CO2eq in 2004, but sharply decreased from 10,284 kilotons of CO2eq in 2005 to 3,906 kilotons of CO2eq in 2020. It was also found that the most commonly used method for controlling the emissions of F-gases from the semiconductor and optoelectronic industries was based on the thermal destruction-local scrubbing technology.

In an effort to enhance the efficiency and safety of open-pit mines, this study explores the optimization of end slope road parameters and slope structures, specifically focusing on unmanned driving lanes.A significant aspect of the study is the development of a truck trajectory offset model, which considers the different reaction times between automated sensors and human drivers in adapting to environmental changes. To test these concepts, the study uses numerical simulations to confirm the stability of the proposed end slope designs. Using Victory West Mine No. 1 as a case study, the research determines the optimized width for unmanned driving lanes and the maximum angle for safe steepening of end slopes. The findings indicate that the optimized unmanned lane width for NTE240 mining dump trucks is 1743 mm, allowing for a 2-degree increase in the slope angle at the south end slope. This optimization leads to a steep mining stripping volume of 3.2735 million m³ and a coal output of 2.49628 million tons, maintaining a stripping ratio of 1.31m³/t. These results demonstrate that the unmanned driving road width optimization not only ensures slope safety but also significantly boosts the economic benefits of steep mining in open-pit mines.

The purpose of this study is to elucidate the factors influencing the voluntary adoption of IFRS by examining, analyzing, and synthesizing findings from empirical studies conducted worldwide. The research scrutinizes 185 relevant studies on the voluntary adoption of IFRS published before August 2023. Our assessment reveals that, in prior research, the factors influencing the voluntary adoption of IFRS are categorized into seven main factors, including corporate operations, capital structure, ownership structure, internationalization, financial performance, corporate governance, and several other factors. These studies employ various methodologies, including data surveys, and cross-sectional data, to estimate the relationships between these factors and the voluntary adoption of IFRS. In addition to providing an evaluation of the research in this field, this study can serve as a framework for future researchers to link and compare the results of different studies. We anticipate that this research will be beneficial for future scholars interested in the factors influencing the voluntary adoption of IFRS. Furthermore, the study proposes essential guidance for future research considerations.

Purpose: We evaluated the outcomes of fluid-gas exchange (FGE) for long-term flap closure of idiopathic macular hole (MH) after the inverted internal limiting (ILM) flap technique. Methods: We included eyes showed flap closure without complete MH closure, connection of the apart macular tissue, 1 month postoperatively after the inverted ILM flap technique. The eyes stayed at flap closure at 2 months postoperatively further underwent in-office FGE with 16% C3F8. Results: Among 10 eyes, 5 eyes (50%) showed flap closure at 2 months postoperatively further underwent FGE for complete MH closure while the remaining 5 eyes (50%) progressed directly at 2 months postoperatively. The improvement in vision of all flap closure from baseline was significant (p=0.015), with the mean baseline vision was 1.19 [Snellen equivalent (SE), 20/307] ± 0.52 logMAR and the mean final vision being 0.63 (SE, 20/85) ± 0.38 logMAR. The group that underwent FGE showed a better final vision of 0.45 (SE, 20/75) ± 0.23 logMAR than the group that didn’t undergo FGE (0.81 [SE, 20/128] ±0.44 logMAR). All eyes achieved complete MH closure, including the eyes that underwent FGE in a mean period of 5.60 months (range 3-10 months) after the inverted ILM flap technique. The eyes that underwent FGE achieved higher rate of foveal restoration [complete external limiting membrane (ELM): 80%; complete ellipsoid zone (EZ): 60%] than those that didn’t receive FGE (complete ELM: 40%; complete EZ: 10%). Conclusions: Eyes that underwent FGE accelerated complete MH closure and showed better final vision and fovea l restoration.

Here, we present a staged approach for an innovative repurposing of a portable infant humidicrib into a live cell growth, observation, and imaging system. Furthmore, humidicrib can support different variations of “umbilical” bioreactors, and can be used to conduct electrophysiology experiments and in situ immunohistochemistry. Modifications incorporate a closed loop carbon dioxide (CO₂) concentration control system with umbilical CO₂ and heating support for tailored bioreactors. The repurposing cost is inexpensive and allows for the continued observation and imaging of cells. This prototype unit has been used to continuously observe and image live primary neurons for up to 21 days. This demonstrates the repurposed units’ suitability for use in tissue culture based research, particularly where modifications to microscopes are required or where sensitive manipulation outside of a standard incubator is needed.

Entrepreneurship has been viewed as an opportunity for economic development and changing economic scenarios in global markets. Women are viewed as a reservoir of entrepreneurial talent, so they can be growth engines in novel markets. Previous studies have considered entrepreneurship as the most effective way towards the economic empowerment of women. Female students engaged in entrepreneurial education have been addressed persistently, while what transforms them in an education process is still unclear. Considering the transforming global economy and its influence on higher education, this study aims to detect female students transforming entrepreneurial competency, mindset, and intention into sustainable entrepreneurship. Using a self-compiled survey, we targeted 752 female students to investigate their entrepreneurial competency, mindset, and intention. SPSS and AMOS were used to transform the data for interpretation. We assumed that the impact of female students’ entrepreneurial competency could be modified by an entrepreneurial mindset and result in entrepreneurial intention. To detect this causal relationship, this study employed reliability, factor, structural equation modeling (SEM), and bootstrap-ping analyses to verify the evidence. The result of the SEM confirms that female students’ entrepreneurial competency will, through their entrepreneurial mindset, impact entrepreneurial intention. With bootstrapping, 5000 samples were collected, and it was demonstrated that the measure constructs were still reliable in the model. This study found that there is a mediation effect between entrepreneurial competency and entrepreneurial intention. The entrepreneurial mindset plays a crucial role in the transformation process. Without an entrepreneurial mindset, entrepreneurial competency cannot exert a significant effect on entrepreneurial intention. The findings can help reinvent related entrepreneurial education in higher education.

Severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) is pandemic. Prevention and control strategies require an improved understanding of SARS-CoV-2 dynamics. We did a rapid review of the literature on SARS-CoV-2 viral dynamics with a focus on infective dose. We sought comparisons of SARS-CoV-2 with other respiratory viruses including SARS-CoV-1 and MERS-CoV. We examined laboratory animal, and human studies. The literature on infective dose, transmission, and routes of exposure was limited specially in humans, and varying endpoints were used for measurement of infection. We propose the minimum infective dose of COVID-19 in humans, is higher than 100 particles, possibly slightly lower than the 700 particles estimated for H1N1 influenza. Despite variability in animal studies, there was some evidence that increased dose at exposure correlated with higher viral load clinically, and severer symptoms. Higher viral load measures did not reflect COVID-19 severity. Aerosol transmission seemed to raise the risk of more severe respiratory complications in animals. An accurate quantitative estimate of the infective dose of SARS-CoV-2 in humans is not currently feasible and needs further research. Further work is also required on the relationship between routes of transmission, infective dose, co-infection, and outcomes.

Ensuring equal access to affordable higher education for women and men has become a crucial target of UNESCO’s SDG4-Education 2030. Currently, about one-third of the world's college-age population participates in higher education, while the gender disparity persists in various systems. This study employed GDP per capita, gross enrollment ratio (GER), and the gender parity index (GPI) to demonstrate how the education systems have expanded resulting in the transformation of gender parity. We selected Japan, Korea, Taiwan, and the UK as research targets using a cross-correlation function and trend analysis to detect concurrent relationships and future trends with GDP per capita, GER, and GPI. The findings suggest Japan, Korea, and the UK continue to show gender disparity and need to respond to this issue in their policy intervention for SDG4-Education 2030. The results reveal a potential problem in the UK when GPI growth might become unlimited with females dominated. This study suggests the higher education expansion phenomenon and gender diversity in mass and universal systems can be detected by the trend analysis with GDP per capita, GER, and GPI in different settings. The design of the study provides an example to explore the gender diversity patterns in higher education systems for sustainable development.

In this paper, a novel permanent magnet-assisted synchronous reluctance machine (PMASynRM) with rare-earth PMs and ferrite magnets is proposed. The performance of PMASynRM is discussed with respected to the different magnet ratio of rare-earth PMs and ferrite magnets. Some characteristics including the flux density, output torque, cogging torque, output power, power factor, torque ripple, loss, efficiency, and demagnetization are calculated by 2-D finite element analysis (FEA). The analysis results show that the excellent performance can be obtained by using hybrid magnet of rare-earth PMs and ferrite magnets with the suitable magnet ratio, and provide some desirable cost-performance trade-off.

The aim of this study is to evaluate the optimal conditions of membrane filtration process. Both laboratory test and pilot-scale test were conducted to examine a treated water on blending water. The water sample were prepared by blending a raw water and the effluent water filtered through an organic membrane. The optimal efficiency in the treatment of water quality at the lab-scale test was generated under conditions of flux at 2.0 m³/m²∙day, the blending ratio of 4:1, and the optimal dosage of coagulant at 20 ppm. The pilot-scale test resulted in that the optimal efficiency was obtained under conditions of flux at 2.0 m³/m²∙day and the blending ratio of 6.0:1. However, the different results between lab-scale and pilot-scale tests on the optimal dosage of coagulant implied that it is difficult to achieve the stable condition of process operation at the low level of coagulant. In summary, the results indicated that, in the combination process of organic membrane and ceramic membrane, the recovery efficiency was achieved above the level of 98.4 %. Compared to 92.1 % in a single organic membrane process, the combination process is 6.3 % more efficient than the single one. This combination process of water treatment lead to stable recovery rates by the optimal input of dosage, less pollution load to water, and a stabilized filtration system.

Cement-free concrete has superior physical performance, such as strength and durability, compared to OPC concrete, however, it has the disadvantage of large shrinkage. Large shrinkage can cause cracks due to shrinkage stress in the long term. In this study, a shrinkage reducing agent (SRA) was used to reduce the shrinkage of cement-free mortar; its content was increased from 0.0 to 1.5 %. For an SRA content of 1.0 %, a calcium sulfoaluminate (CSA) expansive additive (EA) (2.5, 5.0, and 7.5%) was added. To calculate the shrinkage stress of cement-free mortar using the SRA and EA, the compressive strength, elastic modulus, and total and autogenous shrinkage were measured. The unit shrinkage stress of cement-free mortar was obtained by multiplying the elastic modulus by the length change and accumulated to obtain the shrinkage stress acting on the mortar according to the age. The shrinkage stress of cement-free mortar showed different tendencies as the age increased. At early ages, the shrinkage rate of the mortar occupied a large proportion of the shrinkage stress. In the long term, the shrinkage stress was significantly affected by the elastic modulus. As a result, SRA was found to be effective in reducing the shrinkage stress by decreasing both the elastic modulus and shrinkage. However, EA increased the shrinkage stress over the long term due to an increase in elastic modulus even though it compensated for early-ages shrinkage.

Rapid and accurate detection of road cracks is of great significance for road health monitoring, but currently this work is mainly completed through manual site surveys. Low-altitude UAV remote sensing can obtain images with centimeter or even subcentimeter ground resolution, which provides a new efficient and economical approach for rapid crack detection. Nevertheless, crack detection networks face challenges such as edge blurring and misidentification due to the heterogeneity of road cracks and the complexity of the background. To address these issues, we propose a real-time edge reconstruction crack detection network (ERNet) which adopts multi-level information aggregation to reconstruct crack edges and improve the accuracy of segmentation between the target and background. To capture global dependencies across spatial and channel levels, we propose an efficient bilateral decomposed convolutional attention module (BDAM) that combines depth separable convolution and dilated convolution to capture global dependencies across spatial and channel levels. To enhance the accuracy of crack detection, we use a coordinate-based fusion module that integrates spatial, semantic, and edge reconstruction information. In addition, we propose an automatic measurement of crack information for extracting the crack trunk and its corresponding length and width. Experimental results demonstrate that our network achieves the best balance between accuracy and inference speed.

Power quality is a major concern in electrical power systems. The power quality disturbances such as sags, swells, harmonic distortion and other interruptions have impact on the electrical devices and machines and in severe cases can cause serious damages. Therefore it is required to recognize and compensate all types of disturbances at an earliest to ensure normal and efficient operation of the power system. To solve these problems, many types of power devices are used. At the present time, one of those devices, Dynamic Voltage Restorer (DVR) is the most efficient and effective device used in power distribution system. In this paper, design and modeling of a new structure of multifunctional DVR for voltage correction is presented. The performance of the device under different conditions such as voltage swell, voltage sag due to symmetrical and unsymmetrical short circuit, starting of motors, and voltage distortion are described. Simulation result shows the superior capability of proposed DVR to improve power quality under different operating conditions. The proposed new DVR controller is able to detect the voltage disturbances and control the converter to inject appropriate voltages independently for each phase and compensate to load voltage through three single- phase transformers.

Lateral vehicle control is a high importance in automated vehicles as it directly influences the vehicle’s performance and safety during operation. The Linear Quadratic Regulator (LQR) controller stands out due to its high-performance characteristics and is used in the open source for self driving functions. However, a notable limitation of the current approach is the manual calibration of LQR controllers based on the experience and intuition of the designers, leading to empirical uncertainties. To address this issue and enhance the lateral control performance, this paper concentrates on refining the LQR by employing three optimization algorithms: Artificial Bee Colony Optimization (ABC), Genetic Algorithm (GA), and Particle Swarm Optimization (PSO). These algorithms aim to overcome the reliance on empirical methods and enable a data-driven approach to LQR calibration. By comparing the outcomes of these optimization algorithms to the manual LQR controller within an offline multibody simulation as testing platform, the study highlights the superiority of the best-performing optimization approach. Following this, the optimal algorithm is implemented on a real-time system for the full vehicle level, revealing the Model-in-the-Loop and the Hardware-in-the-Loop gap up to 78,89% with lateral velocity when we use Relative Error Criterion (REC) method to validate and 2.35m with lateral displacement when considering by maximum absolute value method.

Heat dissipation from Li-ion batteries is a potential safety issue for large-scale energy storage applications. Maintaining low and uniform temperature distribution, and low energy consumption of the battery storage is very important. We studied the fluid dynamics and heat transfer phenomena of a single cell, 16-cell modules, battery packs, and cabinet through computer simulations and experimental measurements. The results show that the temperature distribution of single cell is relatively uniform when the cell is facing the air flow. In a module, very high air flow rate and large gap between the cells can reduce the cell temperature. A pack with a good thermally conductive case is very important to ensure good heat dissipation of the battery module. Due to limited space in the cabinet, additional air inlets and outlets can be opened outside of the cabinet to slightly lower the pack temperature. Installing fins outside the cabinet can also slightly reduce the temperature inside the cabinet. Liquid cooling medium, such as water, is much better than the air-cooling medium.

In this study, we analyzed the microbial community of traditional fermented foods in Jeju Island to identify the distribution of useful microorganisms and confirm their anti-inflammatory and anti-melanogenic effects to determine their potential use as cosmetic ingredients. Firstly, we examined the microbial communities of Omphalius rusticus Jeotgal (OR), Spratelloides gracilis Jeotgal (SG), Chromis notata Jeotgal (CN), Turbo cornutus Jeotgal (TC), Trichiurus lepturus intestine Jeotgal (TL), Branchiostegus japonicus Sweet Rice Punch (BJ), Salted Anchovy Sauce (SA), Jeju Soy Sauce (JSS), and Jeju Soybean Paste (JSP). We found that Latilactobacillus sakei (87.2%), Tetragenococcus halophilus (37.7%), T. halophilus (96.8%), Bacillus subtilis (23.4%), T. halophilus (71.3%), L. sakei (53.7%), Lentibacillus sp. (42.9%), Enterococcus durans (14.6%), and E. durans (32.8%) were the dominant species. Secondly, to study the nine Jeju fermented foods’ anti-inflammatory and anti-melanogenic effects, we employed RAW 264.7 and B16F10 cells, classic cell models for inflammation and melanogenesis studies. Ethyl acetate extracts of the nine Jeju fermented foods all inhibited nitric oxide (NO) and melanin production in a concentration-dependent manner. Thirdly, to test the applicability of the nine Jeju fermented foods to human skin, we used the MTT assay to assess their cytotoxic effects on human keratinocytes (HaCaT cells). Finally, the topical applicability of the nine Jeju fermented foods was tested through primary skin irritation, and it was found that they did not cause any adverse effects. Therefore, extracts from the nine Jeju fermented foods have potential applications as ingredients in anti-inflammatory and anti-melanogenic products and can be used in the cosmetic industry.

Insulated Gate Bipolar Transistor (IGBT) may convey high current and sustain high breakdown voltages; it may provide high power control. In a sense, how IGBT demonstrates the capability of power control was not specifically described, and the equivalent bipolar junction transistors (BJT) activated by an applied bias to the insulated gate is intriguing. As seen in Figure 1, IGBT shows an equivalent circuit structure containing two types of BJT, (NPN-type Bipolar transistor and PNP-type Bipolar transistor), which can be modeled as diode-associated transistor. Apparently, as a bias applies to the controlling gate, the channel beneath the gate oxide gets strongly inversed and turns out to be conductive just like what happens on metal-oxide-silicon field effect transistor (MOSFET), which provides necessary igniting currents to both BJTs and thus causes high current gain flowing through them-selves from the bottom. A proposed and renewed formula provides addressing the above scenario and successfully fitting the measured data that forms the characteristic curves. Some parameters in the proposed formula, which includes size and mobility associated constant, threshold voltage, and Early-Voltage-related lambda for MOSFET, explain and explore the underlying physics. IGBT thus enjoy high input impedance and high current gain due to MOSFET (Insulated Gate) and BJT, respectively. This formula combines both merits of MOSFET and BJT in order to fit the measured data. Indeed, the formula intimately fits IGBT electrical characteristic curves, and thus may be qualified and served as a model. The new model is then advisable for designing power integrated circuit to exactly achieve power saving, power control, and power efficiency.

This article aims to identify the current development of cross-border tourism between Vietnam and China. The paper analyzes the perception and strategy of cross-border tourism development in the two countries, especially in the context of China’s implementation of the “Belt and Road Initiative” (BRI). The article emphasizes that Vietnam and China have recently made efforts to promote cross-border tourism development. At the same time, Vietnam and China see cross-border tourism development as a significant part of comprehensive border cooperation between the two countries. However, the development plans for cross-border tourism between the two countries are still mainly on the desk, not yet implemented effectively. Thus, its achievements are relatively modest. Besides, the article emphasizes that the interests of the people living in the border area, especially the Vietnam side, are almost “forgotten” in the development of cross-border travel between the two countries. Besides, the article also analyzes the challenges that the two sides are facing, especially the Vietnam side, in promoting the development of cross-border tourism between the two countries.

Energy and Environment Tax is used globally as a means of environment policy. Energy and Environment tax plays an important role as a driving force for the conversion to environmentally friendly energy. The basic tax principles considered in the design of energy and environmental taxation increases the efficiency of policy instruments. The purpose of this study is to evaluate South Korea’s energy and environmental taxation based on tax principles, namely, equity, efficiency, simplicity, flexibility, and accountability and to suggest directions for improvement. This study applied a methodology that provides policy implications, such as reviewing existing literature and comparing energy and environmental taxes. Results of this study show that South Korea’s energy and environmental taxation is negative in terms of equity, simplicity, and accountability. South Korea’s current energy and environmental tax is regressive to income classes and complex tax structures and it does not objectively measure the impact of energy and environmental taxation. However, energy and environmental taxation is evaluated positively in terms of efficiency and flexibility because it meets the greenhouse gas reduction policy and operates a flexible tax rate. The results of this analysis provide policy implications for reorganizing South Korea’s energy and environmental taxation

The task of weakly supervised point cloud semantic segmentation has received widespread attention and also has been widely used in autonomous driving, robotics, and modern industries. Due to the high dimensionality and large volume of point cloud data, many technical difficulties appeal to weakly supervised semantic processing, especially segmentation. However, weakly-supervised schemes usually provide only partial labelling information of the underlying point cloud data and thus need to effectively extract local features, geometric information, and contextual relationships only using these limited labelled data for supervised learning. To improve weakly-supervised semantic segmentation, we propose a novel segmentation network through the boundary-based feature aggregation based on a K-NN algorithm with down-sampling operation, and also introduce the smoothness loss and Siamese loss for effective segmentation. The experiments on public datasets demonstrate that our presented segmentation method exceeds most of the existing fully supervised and weakly-supervised methods in terms of mIoU. Specifically, our network has high segmentation accuracy on the labels of objects with similar geometrical structures, such as ceiling, wall, floor, chair and table, reaching 91.2%, 98.8%, 83.3%, 75.3% and 80.2%, respectively. Extensive experiments also illustrate its robustness, effectiveness, and generalization of the proposed weakly supervised segmentation network.

The study addresses the urgent environmental issue of climate change, focusing specifically on the role of local food, which is produced and consumed locally, helps reduce carbon emissions by eliminating the need for long-distance transportation. Through quantitative analysis, this study elucidates the potential benefits in environmental impact achieved through the consumption of local food: the significant reduction in carbon emissions. Specifically, the consumption of local food is found to yield an annual decrease of 2,421,296 tCO2 emissions, representing 2.5% of South Korea’s total greenhouse gas emissions from the transportation sector. This reduction further translates into an estimated economic value of USD 54.23 million (KRW 70.5 billion). This study underscores the potential of local food consumption as a tangible strategy to overcome environmental problems. Moreover, its academic contribution lies in its comprehensive analysis of the economic and empirical impacts of local food consumption on environment. Moving forward, we propose policies such as supporting local food distribution networks, providing public education on local food, fostering the local food industry, and providing incentives to revitalize local food consumption.

As medical care aiming to maintain the quality of life for elderly patients is increases, implant treatment for elderly patients is increasing worldwide. Therefore, we aimed to investigate implant stability and the reliability of different measuring devices according to implant placement site and duration in patients aged over 65 years. The study evaluated 60 implants in 60 patients aged ≥ 65 years. The implant placement sites were divided into six evenly distributed sections (n=10) i.e., maxillary right- posterior, A; maxillary anterior, B; maxillary left-posterior, C; mandibular right-posterior, D; mandibular anterior, E; mandibular left-posterior, F. Participants visited the hospital seven times: preoperatively, 1V; implant surgery, 2V; stitch removal, 3V; 1-month follow-up, 4V; 2-months follow-up, 5V; before final-restoration delivery, 6V; and after final-restoration delivery, 7V. The implant stability was evaluated with the Osstell Mentor (ISQ), Periotest M (PTV), and Anycheck (IST). The mean values of ISQ, PTV, and IST were analyzed (α=.05). ISQ, PTV, and IST results of 5V and 6V were significantly higher than those of 2V (P<.05). The lowest ISQ results occurred in E location at 5V and 6V (P<.05). In all mandibular locations, IST results of 7V were significantly higher than those of 2V, 3V, 4V, and 5V (P<.05). ISQ results were negatively correlated with PTV and positively correlated with IST, and PTV was negatively correlated with IST. By considering various factors that affect implant stability, the appropriate implant load application time was determined. This could help increase the implant success rate in elderly patients. And as a diagnostic device for implant stability for evaluation of osseointegration in elderly patients, Anycheck was also able to prove its relative reliability compared to Osstell ISQ Mentor and Periotest M.

This study aimed to improve sensitivity of ferrous particle sensors used in various mechanical systems such as wind power gearboxes to detect abnormalities by measuring the amount of ferrous wear particles generated by metal-to-metal contact. Existing sensors collect ferrous particles using a permanent magnet. However, its ability to detect abnormalities is limited because it only measures amounts of ferrous particles collected on the top of the sensor. To overcome this limitation, this study evaluated sensibility of an existing sensor using a multi-physics analysis method and improved it by changing the core shape inside the sensor. The detection ability of the improved sensor was analytically shown to be better than the existing sensor. This study highlights the use of analytical methods and multi-physics analysis for developing a ferrous particle sensor and presents a method to compare sensibility analytically. Results of the improved sensor are expected to enhance the ability to detect abnormalities in the lubrication system where ferrous wear particles are generated. This study will contribute to the development of more effective ferrous particle sensors, which can potentially improve the performance and reliability of mechanical systems.

In this study, the literature on varnish contamination is investigated among the various con-taminations of lubricant. As the period of use of lubricant increases, the lubricant deteriorates and becomes contaminated. The varnish causes filter plugging, sticking of hydraulic valves and fuel injection pumps, obstruction of flow, reduction of clearance, poor heater and cooler perfor-mance, and increase of friction and wear in various lubrication systems. These problems also cause mechanical system failure, performance degradation, and increased maintenance and re-pair cost. To improve the problems causes by the varnish, an adequate understanding of varnish is required. Therefore, in this literature review, definitions and characteristics, generating ma-chinery, generating mechanisms, causes, measurement methods, and prevention or removal methods are summarized. Most of the data are reports of companies related to lubricant and machine maintenance, and are included in some papers. We hope that this summary of varnish will be helpful to those who are engaged in reducing or preventing varnish problems.

Contrast agents developed for X-ray computed tomography (CT) offer extremely valuable tools and techniques in diagnostics via contrast enhancements. Heavy metal-based nanoparticles (NPs) can provide high contrast in CT images. These result from a high density of heavy metal atoms with high X-ray attenuation coefficients that exceed that of iodine (I), which is currently used in hydrophilic organic CT contrast agents. Nontoxicity and colloidal stability are vital characteristics in designing heavy metal-based NPs as CT contrast agents. In addition, the particle size must be small for in vivo renal excretion. In vitro phantom imaging studies can provide X-ray attenuation efficiency, which is a critical parameter for CT contrast agents, and the imaging performance of CT contrast agents can be demonstrated via in vivo experiments. This review focuses on in vitro and in vivo studies of various heavy metal-based NPs (metal: Au, Pt, Pd, Ag, Ce, Gd, Dy, Ho, Yb, Ta, W, and Bi) and provides an outlook on their use as high-performance CT contrast agents.

In this paper, we study the well-posedness and asymptotics of a one-dimensional thermoelastic laminated beam system either with or without structural damping, where the heat conduction is given by Fourier's law effective in the rotation angle displacements. We show that the system is well-posed by using Lumer-Philips theorem, and prove that the system is exponentially stable if and only if the wave speeds are equal, by using the perturbed energy method and Gearhart-Herbst-Prüss-Huang theorem. Furthermore, we show that the system with structural damping is polynomially stable provided that the wave speeds are not equal, by using the second-order energy method.

In this study, based on a new quantum integral identity, the authors establish some quantum estimates of Hermite-Hadamard type inequalities for convex functions. These results generalize and improve some known results given in literatures.

Concrete is more stable than filler as a false roof in a downward approach type infill quarry, but the mechanical model of a concrete false roof is not clear. As a result, there has been limited application. Therefore, it is necessary to establish the mechanical model of a concrete artificial false roof to enhance the stability of the downward approach infill quarry. This paper combines theoretical analysis, model derivation, finite element analysis and field application methods. Firstly, the basic assumptions of thin plate theory and elasticity mechanics are used as the premise to establish the differential equations of the deflection curve of the concrete thin plate false roof. Then, the three types of bending moment generation of the concrete thin plate false roof are explored. Secondly, the relationship between the location of dangerous surface and dangerous point in hard-supported weak-slab structure and soft-supported weak-slab structure is analyzed, and the type of uniform load and calculation model of concrete thin-slab false roof are improved. Finally, according to the established mechanical model of thin slab false roof, finite element analysis and field application were carried out. The results show that there are three types of deflection curve differential equations in the concrete thin slab false roof perpendicular to the strike, and three extreme points exist in the middle section of the thin slab and on both sides of the surrounding rock. The hazardous surface of the hard-supported weak-slab structure is present at the intersection of the encircling rock and the thin-slab fake ceiling, with the perilous point situated on the top of this surface. The hazardous surface of the soft-supported weak-slab structure can be found in the centre section of the thin-slab fake ceiling, with the perilous point being located at the bottom of this surface. Moreover, the damage mode for both structures is that of maximum tensile stress damage. Upon conducting a finite element analysis, the results indicate that the concrete's maximum tensile stress is significantly high.

Epoxy was blended with benzoxazine resin and aluminum trihydrate (ATH) additive to render flame retardancy while maintaining mechanical properties. The ATH was modified using three different silane coupling agents and then added to 60/40 epoxy/benzoxazine mixtures. The effect of blend compositions and surface modification on flame retardant and mechanical properties of the composites was investigated by UL94, tensile, and shear tests. Resin mixtures containing more than 40 wt% benzoxazine revealed a UL94 V-1 rating with enhanced tensile and shear strength. Upon addition of 20 wt% ATH to 60/40 epoxy/benzoxazine, a V-0 rating was achieved. The lowered tensile and adhesive properties of the composites in the presence of ATH were improved by modifying the ATH surface using silane coupling agents.

Practical applications of CsPbX3 nanocrystals (NCs) are limited by their poor stability. The formation of heterojunction between CsPbX3 NCs and oxides is an effective means to protect perovskite from polar solvents and other external factors. Significantly improving the stability and photocatalytic properties of the core/shell perovskite is very important for its application in photoelectric and photocatalytic technology. Here, we report the synthesis of asymmetrical CsPbBr3/TiO2 core-shell heterostructure NCs at single particle level by hot injection liquid phase synthesis and sol-gel method, where each CsPbBr3 NCs is partially covered by titanium dioxide. It is shown that the type II arrangement is generated at the heterogeneous interface, which greatly facilitates the separation of electron-hole pairs and increases the carrier transport efficiency. More crucial, due to the protection of titanium dioxide shell, the product has higher long-term stability in humid air compared with bare CsPbBr3 NCs. The asymmetrical core-shell heterostructure prepared in this study not only improves the stability of CsPbX3 NCs, but also provides some ideas for optoelectronic device applications and TiO2-based photocatalysts.

Hepatocellular carcinoma (HCC) is currently the third leading cause of malignancy-related mortalities worldwide. Natural killer (NK) cells are involved in the critical role of first line immunological defense against cancer development. Defects in NK cell functions are recognized as important mechanisms for immune evasion of tumor cells. NK cell function appears to be attenuated in HCC, and many previous reports suggested that NK cells play a critical role in controlling HCC, suggesting that boosting the activity of dysfunctional NK cells can enhance tumor cell killing. However, the detailed mechanisms of NK cell dysfunction in tumor microenvironment of HCC remain largely unknown. A better understanding of the mechanisms of NK cell dysfunction in HCC will help in the NK cell-mediated eradication of cancer cells and prolong patient survival. In this review, we describe the various mechanisms underlying NK cell dysfunction in HCC. Further, we summarize current advances in the approaches to enhance endogenous NK cell function and in adoptive NK cell therapies, to cure this difficult-to-treat cancer.

The increasing prevalence of obesity and sedentary lifestyles has led to an increased incidence of metabolic syndrome (MetS) worldwide. In Taiwan, middle-aged women are at a greater risk of MetS, type 2 diabetes, and cardiovascular disease than men are because they have more subcutaneous fat and larger waist circumferences compared to men with equal visceral fat levels. This study investigated the effects of calorie restriction supplemented with fish oil (CRF) in middle-aged women with MetS. For 12 weeks, 75 eligible participants were randomly assigned either calorie restriction (CR) or CRF. Both dietary intervention groups were further divided into two age groups: ≤45 and >45 years. The changes in MetS severity, inflammatory status, iron status, and red blood cell fatty acid profile were evaluated. Seventy-one participants completed the trial. Both dietary interventions significantly ameliorated MetS and improved the participants’ inflammatory status. CR significantly increased total iron binding capacity, whereas CRF increased hepcidin levels. Furthermore, CRF significantly increased the n-6/n-3 and arachidonic acid/docosahexaenoic acid ratios. In conclusion, CR and CRF improved the anthropometric and MetS characteristics of early-middle aged women, including body weight, blood glucose levels, triglyceride levels, as well as the scores for the homeostasis model assessment of insulin resistance and quantitative insulin sensitivity cheque index. Dietary intervention was more effective in >45-year-old women than ≤45-year-old women.

Background and Objectives: High rates of psychiatric disorders and comorbidities have been reported in juvenile detainees which have been associated with repeat offenses. However, research on this topic has been limited to Asian countries. This study aimed to examine the prevalence of psychiatric disorders and sexual differences among juvenile detainees in a detention center in South Korea. Materials and Method: The participants comprised 54 males and 46 females, with a minimum intelligence score of 80. Psychiatric diagnosis was determined using the Mini-International Neuropsychiatric Interview for Children and Adolescents (MINI-KID). The Massachusetts Youth Screening Instrument-Version 2 (MAYSI-2) was used to investigate gender differences. Results: Using the MINI-KID, the most frequent diseases were conduct disorder (CD), alcohol dependence, suicidal tendency, attention-deficit/hyperactivity disorder (ADHD) with statistically significant differences between men and women. Only alcohol abuse was higher in men while the rest were higher in women. The items with a statistically significant gender difference in MAYSI-2, were alcohol/drug use, feeling depressed/anxious, somatic complaints, suicidal ideation, and traumatic experience. All items for which the gender difference was statistically significant were higher in the proportion of women. Conclusions: Juvenile detainees exhibit high rates of psychiatric disorders and comorbidities. CDs, alcohol dependence and ADHD are the most common psychiatric disorders among juvenile detainees in South Korea. Assessment of and intervention in psychiatric disorders may help prevent further offenses. These findings highlight the importance of diagnosing and intervening in psychiatric disorders within juvenile detention systems.

Nonsteroidal anti-inflammatory drugs (NSAIDs), which block the activity of cyclooxygenase (COX) isoenzymes and inhibit the synthesis of prostaglandin, have been used for pain relief. We have developed a method to separate a mixture of three NSAIDs, such as aspirin, paracetamol, and naproxen, using reverse-phase high-performance liquid chromatography (RP-HPLC). An isocratic mobile phase consisting of acidic water and acetonitrile was selected to run at a low flow rate, such as 0.8 mL/min. The mixture of three NSAIDs was injected at a low volume into a C18 column that was 150 mm in length and characterized using a UV detector at 230 nm. We identified three peaks in the chromatogram indicating the three compounds. The elution time of the peaks was less than 10 minutes. To identify multiple peaks on the isocratic flow using a short column, further studies are required regarding the proposed method to generate microfluidic devices for nanoLC.

Abstract: Background: The optimal strategy for the microelimination of HCV within community settings remains ambiguous. We evaluated the percentage of participants who achieved linkage to care (LTC) following the conclusion of the screening campaign, and examined the diverse factors influencing LTC among these individuals. The effectiveness of recall intervention for the non-LTC population and its barriers were analyzed. Methods: We initiated an HCV patients recall program to identify the HCV participants who might not be treated after the HCV screening campaign. A program staff recalled HCV participants who lost to follow-up through the telephone from March 2019 to June 2019. They were informed of HCV treatment's importance, efficacy, availability, and safety. Result: Among 185 HCV-infected participants, 109 (58.9%) HCV-infected participants had obtained LTC. Compared with those who had LTC, those without LTC were older, lower education levels, were less aware of their HCV infection, less frequently lived in urban areas, and had less health insurance. At the end of the recall program, 125 (67.6 %) persons had liked to care. The proportion of LTC increased by 8.7 %. 119 persons had an HCV RNA test, and 82 (68.9%) had viremia. Of 82 patients with viremia, 78 (95.1%) received antiviral therapy. 76 (97.4 %) of them achieved a sustained virological response. Conclusion: After a community screening campaign, 59 % of participants with anti-HCV positive had LTC. The recall program can increase by 9 %. However, there were still 32% of HCV participants who couldn't be linked to care. Outreach care for non-LTC patients is a way worth trying to achieve micro-elimination of HCV in the rural community.

This paper examines the moral community thesis in the secular context of China. Using multilevel logistic regression, we test (1) whether both individual- (measured by affiliation with institutional religion) and aggregate-level religiosity (measured by the number of religious sites per 10,000 people in province) are inversely related to law and rule violations at the individual level and (2) whether the province-level religiosity enhances the inverse relationship between individual religiosity and the deviant behaviors. Results from analyzing data from the 2010 China General Social Survey and the Spatial Explorer of Religions show that both individual- and aggregate-level religiosity are inversely related to the odds of violating the law and various rules of government, transportation, workplace, and other organizations. However, the cross-level interactions are not significant across models, indicating that the contextual religiosity does not increase the effect of individual-level religiosity on deviance. Implications of findings for the moral community thesis are discussed.

In this paper, we consider a fourth-order suspension bridge equation with nonlinear damping term |u_t|^m-2u_t and source term |u|^p-2u. We give necessary and sufficient condition for global existence and energy decay results without considering the relation between m and p. Moreover, when p>m, we give sufficient condition for finite time blow-up of solutions. The lower bound of the blow-up time T_max is also established. It worth to mention that our obtained results extend the recent results of Wang (J. Math. Anal. Appl., 2014) to the nonlinear damping case.

Ce³⁺ and Dy³⁺ ions doped Ca₂Al₂SiO₇ (CAS) phosphors were prepared by the solid-state reaction at 12800C for 1h. X-ray diffraction patterns confirmed a tetragonal crystalline structure. The luminescent spectra of CAS: Ce³⁺, Dy³⁺ phosphors consist a board band with peaking at 420 nm corresponding to the luminescence of Ce³⁺ ions and narrow lines of Dy³⁺ ions. The energy transfer from Ce³⁺ ion to Dy³⁺ ion is presented and discussed

Currently, in some domestic and foreign mines, the backfill drilling pipeline experience a rupture phenomenon even when the wear degree is low. This results in a delay in production due to the filling becoming 'sick'. This paper presents, for the first time, the damage mechanism from a mechanical perspective and re-derives the anti-extrusion strength model of the backfill drilling pipeline. We investigate the influence of law on the anti-extrusion strength of pipelines from the perspective of stratum and cement ring. We then verify the theoretical and simulation results through engineering examples. The results demonstrate that the Mises stress criterion is a suitable modification principle for the anti-extrusion strength model of the backfill drilling pipeline. The anti-extrusion strength of the pipeline is related to the elastic modulus and Poisson's ratio of the stratum, and the thickness of the cement ring. It is negatively affected by the depth of the stratum. For hard strata, a cement ring with a smaller elastic modulus is suitable, while for soft stratum, a cement ring with a larger elastic modulus is recommended. When the missing angle of the cement ring is less than 60°, the stress concentration factor increases up to 2.2. The stress unloading capacity of the cement ring ranges from 32.7% to 37.8%, and optimal performance of the cement ring is achieved when it has high strength and low rigidity. The backfill filling pipeline of a copper mine abroad was destroyed due to external extrusion force exceeding its anti-extrusion strength value. The modified pipeline anti-extrusion strength model is 18.2% higher than the casing API strength value. This finding can inform the design of the backfill filling pipeline for China's kilometer-deep wells in the future.

This paper addresses the input coupling problem for the shape memory alloy (SMA) actuated parallel platform with completely unknown nonlinear dynamics. The problem means that in a parallel platform with multiple SMA actuators acting together, the displacement of one of the actuators will simultaneously affect the remaining actuators to change. Due to the coupling problem and nonlinear characteristics of the SMA actuators, it is not easy to control the platform to achieve bi-directional swing with completely unknown nonlinear dynamics. Therefore, a model-free adaptive sliding mode control method is proposed to improve the control accuracy of the complex motion of the platform, avoiding the complex modeling process of the SMA actuated parallel platform. Based on the model-free adaptive control (MFAC) theory, a multiple input and multiple output (MIMO) dynamic linearized mathematical model of the parallel platform is established using the online input and output data of the system. Then, a sliding mode controller is designed based on the dynamic model. A rigorous theoretical analysis proves that the proposed model-free adaptive sliding mode controller is able to stably control the SMA actuated parallel platform, and its tracking error is uniformly ultimately bounded (UUB). Finally, experiments are conducted on the established SMA actuated parallel platform. The results show that the proposed model-free controller is feasible and effective, and can control the system well to achieve the complex motion of bi-directional swing.

Background and Objectives: Although there has been growing interest in the association of ADHD with anxiety, depression, suicidal ideation, and self-esteem, there is a lack of consistent results and these associations remain unclear. This study investigated the differential patterns of anxiety, depression, suicidal ideation, and self-esteem with regard to the presence of ADHD. Materials and Methods: The subjects were divided into a patient group and a control group. The patient group included 49 patients diagnosed with ADHD at the department of psychiatry of one university hospital. For the control group, 3,727 students were invited to complete a questionnaire. Of the 1,717 students who responded to the questionnaire, 245 were selected for patient-controlled studies. All the subjects were instructed to complete the Beck Suicide Ideation Scale, Children's Depression Inventory, Beck’s Depression Inventory, State-Trait Anxiety Inventory, and Rosenberg Self-Esteem Scale. Results: ADHD subjects experienced more anxiety, depression, and suicidal ideation as well as lower self-esteem compared to the control group comprising participants without ADHD. Conclusions: These findings suggest that ADHD symptoms may contribute to greater suicidal ideation through experienced depression, anxiety, and low self-esteem in school-aged children. Therefore, appropriate ADHD symptom management is necessary to reduce suicidal ideation among school-aged children with ADHD symptoms.

Changes in coastal topography can affect the ecological environment and marine industries. In this study, we analyzed the patterns and causes of changes in shoreline and undersea topography in the Nakdong River estuary in the southeast of South Korea using depth and shoreline surveys of the estuary, as well as data on discharge, suspended sediments, and precipitation in the Nakdong River basin. The results showed that erosion and sedimentation occurred repeatedly owing to complex factors such as the discharge of the estuary and invasion by open sea waves. However, no clear unilateral trend was observed. Unlike previous survey data, a large amount of erosion occurred in the second half of 2020. Previously, sedimentation was the main process, but erosion occurred rapidly, which was observed in the summer of 2020 when the erosion was three times higher than that in other periods owing to the severe rainy season and torrential rains for over a month. In addition, regarding the flow rate and force of the river water outflow, the amount of discharge increased rapidly, causing erosion. Moreover, a strong typhoon in the summer of 2020 affected the topography of the estuary.

Osteoporosis is a common metabolic bone disease in patients with diabetes, which can develop simultane-ously with Type 2 diabetes (T2D) in postmenopausal women. Bisphosphonate (BP) is administered to pa-tients with both the conditions and may cause medication-related osteonecrosis of the jaws (MRONJ). It affects the differentiation and function of osteoclasts as well as thickness of cortical bone through bone mineralization. Therefore, this study aimed to investigate the effects of T2D on osteoclast differentiation and activity as well as cortical bone formation in postmenopausal patients with MRONJ. Tissue samples were collected from 10 patients diagnosed with T2D and Stage III MRONJ in the experimental group and from 10 patients without T2D in the control group. Histological examination was conducted, and expres-sion of dendritic cell-specific transmembrane protein (DC-STAMP) and tartrate resistant acid phosphatase (TRAP) was assessed. Cortical bone formation was analyzed using CBCT images. The number of TRAP-positive osteoclasts and DC-STAMP-positive mononuclear cells were significantly less in the experi-mental group (p < 0.05). Furthermore, the thickness and ratio of cortical bone were significantly greater in the experimental group (p < 0.05). In conclusion, T2D decreased the differentiation and function of osteo-clasts, and increased cortical bone formation in postmenopausal patients with MRONJ.

Promoting green development has become an important way to optimize the ecological and economic structure and promote sustainable development. The Yangtze River Economic Belt is an important economic corridor in China, and it remains to be examined whether the implementation of environmental regulations has enhanced the green total factor productivity (GTFP) of cities. This paper calculates the green total factor productivity of 107 cities within the Yangtze River Economic Belt by using the super-efficient SBM model and the GML index with Chinese city panel data from 2007-2019 and measures the intensity of environmental regulations through textual analysis. The bidirectional fixed-effects model constructed in this paper suggests an inverted U-shaped relationship between environmental regulation and GTFP, which is confirmed by a series of robustness tests. Green technology innovation and advanced industrial structure play a mechanism role in this. In regions with lower levels of green technology and industrial structure, the inverted U-shaped relationship between environmental regulation and green total factor productivity is more significant. In addition, the phenomenon of GTFP rising and then falling because of environmental regulation is more obvious in cities in the middle and upper reaches of the Yangtze River and outside the urban agglomerations. Therefore, when formulating environmental regulation policies, it is necessary to balance the relationship between economic development and environmental protection and harmonize the environment and economic development of the entire Yangtze River Basin.

The teaching and learning environment have changed significantly over the last decade with the integration of an increasing amount of information and communication technologies, especially in distance education due to global pandemics, total lockdowns, isolation, and quarantine periods. The number of numerous virtual and non-virtual tools involved in educational processes is growing day by day. In terms of technological innovations used in learning environments, many researchers and educators are trying their best to bring more creative ideas into the technology- based learning environments. Although higher educational institutions have greatly benefited from the growing number of hardware and software resources in the educational process, they have also faced some setbacks that have harmed the learning processes. These technologies have in turn complicated some of the processes in the learning atmosphere. Therefore, we take Spanish teaching course as an example to present the challenging smarter teaching and learning systems that higher educational institutions face today.

Background: Few studies have investigated the longitudinal association between cervical spondylosis (CS) and migraine by using a nationwide population-based database. Methods: We conducted a retrospective cohort study from 2000 to 2011 identifying 27,930 cases of cervical spondylosis and 111,720 control subjects (those without cervical spondylosis) from a single database. The subjects were frequency-matched on the basis of sex, age, and diagnosis date. The non- cervical spondylosis cohort was four times the size of the cervical spondylosis cohort. To quantify the effects of cervical spondylosis on the risk of migraine, univariate and multivariate Cox proportional hazard regression analyses were used to calculate the hazard ratio (HR) and 95% confidence interval (CI). Results: After a 10-year follow-up controlling for potential confounding factors, overall migraine incidence was higher in the cervical spondylosis cohort than in the non- cervical spondylosis cohort (5.16 and 2.09 per 1,000 people per year, respectively; crude hazard ratio = 2.48, 95% confidence interval = 2.28–2.69) with an adjusted hazard ratio of 2.03 (95% confidence interval = 1.86–2.22) after accounting for sex, age, comorbidities, and medication. Individuals with myelopathy in the cervical spondylosis cohort had a 2.19 times (95% confidence interval = 1.80–2.66) higher incidence of migraine compared than did those in the non- cervical spondylosis cohort. Conclusion: Individuals with cervical spondylosis exhibited a higher risk of migraine than those without cervical spondylosis. The migraine incidence rate was even higher among individuals with cervical spondylotic myelopathy.

In this paper, we study the semilinear pseudo-parabolic equations $\displaystyle u_{t} - \triangle_{\mathbb{B}}u - \triangle_{\mathbb{B}}u_{t} = \left|u\right|^{p-1}u$ on a manifold with conical singularity, where $\triangle _{\mathbb{B}}$ is Fuchsian type Laplace operator investigated with totally characteristic degeneracy on the boundary $x_{1} = 0$. Firstly, we discuss the invariant sets and the vacuum isolating behavior of solutions with the help of a family of potential wells. Then, we derive a threshold result of existence and nonexistence of global weak solution: for the low initial energy $J(u_{0})<d$, the solution is global in time with $I(u_{0}) >0$ or $\displaystyle\Vert \nabla_{\mathbb{B}}u_{0}\Vert_{L_{2}^{\frac{n}{2}}(\mathbb{B})} = 0$ and blows up in finite time with $I(u_{0}) < 0$; for the critical initial energy $J(u_{0}) = d$, the solution is global in time with $I(u_{0}) \geq0$ and blows up in finite time with $I(u_{0}) < 0$. The decay estimate of the energy functional for the global solution and the estimates of the lifespan of local solution are also given.

Cyclin-dependent kinase 4 and 6 (CDK4/6) inhibitors, including abemaciclib, have been approved for the treatment of hormone receptor-positive, HER2-negative advanced, and metastatic breast cancer. Despite the high therapeutic efficacy of CDK4/6 inhibitors, they are associated with various adverse effects, including potentially fatal interstitial lung disease. Therefore, a combination of CDK4/6 inhibitors with letrozole or fulvestrant has been attempted but has demonstrated limitations in reducing adverse effects, highlighting the need to develop new combination therapies. This study proposes a combination strategy using CDK4/6 inhibitors and tricyclic antidepressants to enhance the therapeutic outcomes of these inhibitors while reducing their side effects. The therapeutic efficacies of abemaciclib and desipramine were tested in different cancer cell lines (H460, MCF7, and HCT-116). The antitumor effects of the combined abemaciclib and desipramine treatment were evaluated in a xenograft colon tumor model. In vitro cell studies have showed the synergistic anticancer effects of combination therapy in the HCT-116 cell line. The combination treatment significantly reduced tumor size compared with control or single treatment without causing apparent toxicity to normal tissues. The combination of abemaciclib and desipramine may be a promising therapeutic strategy as they could reduce side effects and enhance tumor suppression.

Taiwan’s auditors have suffered from processing excessive audit data, including drawing audit evidence. This study advances sampling techniques by integrating machine learning with sampling. This machine learning integration helps avoid sampling bias, keep randomness and variability, and target the risker samples. We first apply a Naive Bayes classifier to classify data into some classes. Next, a user-based, item-based, or hybrid approach is employed to draw audit evidence. The representativeness index is the primary metric for measuring the representativeness of audit evidence. The user-based approach denotes the selection of samples between two percentiles in a class as audit evidence. It may be equivalent to a combination of monetary and variable sampling methods. The item-based approach represents the choice of risky samples as audit evidence. It may be identical to a combination of non-statistical and monetary sampling methods. Auditors can hybridize those user-based and item-based approaches to balance representativeness and riskiness in selecting audit evidence. Three experiments show that sampling using machine learning integration has the benefits of drawing unbiased samples, handling complex patterns, correlations, and unstructured data, and improving efficiency in sampling big data. However, the limitations are the classification accuracy output by machine learning algorithms and the range of prior probabilities.

There are rich proper noun derivative semantic relationships in geographic entity vector data. The identification of traditional proper noun derivative semantic relationships usually requires toponym researchers to examine the source of derived toponyms by consulting a large number of toponym documents. This method cannot adapt to the mining of proper noun derivative semantic relationships for large-scale geographical entity. In this regard, this paper proposes a method of identifying the proper noun derivative semantic relationships for geographical entity by combining prompt learning and XGBoost model. This method transforms the extraction problem of proper noun derivative semantic relationships into a binary classification problem by analyzing the characteristics of the derivation relationship of toponyms in the form of toponyms and the spatial and temporal distribution of geography. Firstly, prompt learning and gaussian mixture model are used to extract and cluster the derivation words of toponyms, so as to realize the recognition of derived toponyms collections. Then, enumerate the possible proper noun derivations in the toponym set, and then the XGBoost model is used to identify the semantic relations derived from the proper noun of geographical entities. In the experiment, the recognition method of proper noun derivative semantic relationships based on prompt learning and XGBoost proposed in this paper has achieved good relationship recognition effect in the experiment. This method has certain practical value in the fields of toponym management and toponym translation.

U-Net, based on a deep convolutional neural network (CNN), has been clinically used to au-to-segment normal organs and potentially target volumes. However, CNNs with local geometric dependencies may limit the accuracy of segmentation. Additionally, the performance of CNNs can vary depending on the selection of network hyper-parameters, which was mitigated by the proposition of nnU-Net. We chose a vision transformer architecture called VT U-Net, which features a self-attention excluding the convolution layer, to overcome the limitations of CNNs by utilizing global geometric information of images. The VT U-Net v.2 became more powerful thanks to the adaptive hyper-parameter optimizer embedded in nnU-Net. However, despite leveraging the benefits of nnU-Net, VT U-Net v.2 still had additional network hyper-parameters that needed to be optimally chosen. Accordingly, among various hyper-parameters, this study attempted to find the optimal combination of the patch size and the embedded dimension regarding the transformer. From the 4-fold cross-validation, the modified VT U-Net v.2 showed the highest average performance for planning target volume (PTV) segmentation among the investigated networks. Though nnU-Net was based on convolution layers, the adaptive hyper-parameter optimizers turned out to enhance the performance. It was also confirmed that network hyper-parameters affected the segmentation accuracy of vision transformers.

System-of-systems (SoS) evolution is a complex and unpredictable process. Although various principles to facilitate collaborative SoS evolution have been proposed, there is a lack of experimental data validating their effectiveness. To address these issues, we present an Agent-Based Model (ABM) for SoS evolution in the Internet of Vehicles (IoV) , serving as a quantitative analysis tool for SoS research. By integrating multiple complex and rational behaviors of individuals, we aim to simulate real-world scenarios as accurately as possible. To simulate the SoS evolution process, our model employs multiple agents with autonomous interactions and incorporates external environmental variables. Furthermore, we propose three evaluation metrics: evolutionary time, degree of variation, and evolutionary cost, to assess the performance of SoS evolution. Our study demonstrates that enhanced information transparency significantly improves the evolutionary performance of distributed SoS. Conversely, the adoption of uniform standards only brings limited performance enhancement to distributed SoSs. Although our proposed model has limitations, it stands out from other approaches that utilize Agent-Based Modeling to analyze SoS theories. Our model focuses on realistic problem contexts and simulates realistic interaction behaviors. This study enhances the comprehension of SoS evolution processes and provides valuable insights for the formulation of effective evolutionary strategies.

Quadrotor drones have rapidly gained interest recently. Numerous studies are underway for the commercial use of autonomous drones, and especially the distribution businesses are taking serious reviews on drone delivery services. However, there are still many concerns about urban drone operations. The risk of failures and accidents makes it difficult to provide drone-based services in the real world with ease. There have been many studies that introduced supplementary methods to handle drone failures and emergencies. However, we discovered the limitation of the existing methods. The majority of approaches were improving PID-based control algorithms which is the dominant drone control method. This type of low-level approach lacks situation awareness and the ability to handle unexpected situations. This study introduces an event-based control methodology that takes a high-level diagnosing approach that can implement situation awareness via time-window. While leaving the low-level controller to involve in operating the drone for most of the time in normal situations, our controller operates at a higher level and detects unexpected behaviors and abnormal situations of the drone. We tested our method with real-time 3D computer simulation environments with Unreal Engine[15] and AirSim[31]. We were able to verify that our approach can provide enhanced double safety and better ensure safe drone operations. We hope our discovery to possibly contribute to the advance of real-world drone services in the near future.

In this paper, we study the global existence and exponential decay for a dynamic contact problem between a Timoshenko beam with second sound and two rigid obstacles, of which the heat flux is given by Cattaneo's law instead of the usual Fourier's law. The main difficulties arise from the irregular boundary terms, from the low regularity of the weak solution and from the weaker dissipative effects of heat conduction induced by Cattaneo's law. By considering related penalized problems, proving some a priori estimates and passing to the limit, we prove the global existence of the solutions. By considering the approximate framework, constructing some new functionals and applying the perturbed energy method, we obtain the exponential decay result for the approximate solution, and then prove the exponential decay rate to the original problem by utilizing the weak lower semicontinuity arguments.

Background: During pregnancy, major physiological changes occur in every system. Understanding the hemodynamic changes in different stages of pregnancy can help to identify abnormal states during pregnancy. Harmonic analysis could be a useful tool in monitoring the state of the ventricular-arterial system during pregnancy. The aim of this study was to investigate the specific statistical relationships between changes in harmonic indices during different stages of pregnancy. Methods: A Total of 380 women (190 pregnant women and 190 age-matched non-pregnant women), with ages ranging from 20 to 45, were enrolled in the study. The visit measured the subject’s hemodynamic parameters including heart rate, systolic blood pressure (SBP), diastolic blood pressure (DBP) and photoplethysmography (PPG). SBP and DBP were evaluated by an automatic blood pressure monitor. PPG signal were continuously recorded for 12-seconds using a PPG sensor. Spectrum analysis of the PPG signal was performed to evaluate the first five harmonic components (C1 – C5) and harmonic phases (P1 – P5). Result: A comparison between pregnant women and non-pregnant women showed that the non-pregnant women had lower DBP, C3, C5 and P5 (p<0.05). Waist Circumference, Heart rate, C2, C4 and P2 were higher in pregnant women. Logistic regression analysis was used to determine the associations between pregnancy and harmonics indices. C2, C4 and P3 were positively and P1 and P4 were negatively associated with pregnancy after controlling age, BMI, waist circumference, heart rate, SBP and DBP. Conclusion: The results of this study provide information on the changes in the harmonic frequency components during various stages of pregnancy. The harmonic components of the PPG signal have independent predictive value for changes in a woman's physiology during pregnancy. Since non-invasive PPG measurements can be performed frequently and easily, in the future, it is possible that the hemodynamic changes from some pregnancy-related disorders could be studied by harmonic analysis.

Agricultural activities are the second largest source of greenhouse gas emissions, and carbon emissions from agricultural land use (CEALU) have become a hot issue across the world. However, few scholars explored the impact of agricultural land policies on carbon emissions, such as the High-standard farmland construction(HSFC) in China.Thus，by relying on provincial panel data for China for the period 2005-2017, the effect of the high-standard basic farmland construction policy on carbon emissions from agricultural land use per unit area and its regional differences were quantitatively analyzed using the difference-in-difference (DID) model. The results showed that: 1) China's CEALU per unit area presented a fluctuating upward trend during the period 2005-2017, from 392.58 kg/ha to 457.72 kg/ha, with an average annual growth rate of 1.31%. 2) The high-standard farmland construction(HSFC) policy produced a significant carbon emission reduction effect in agricultural land use, and reduced the CEALU per unit area by 10.80% on average. With the promotion of this policy, its carbon emission reduction effect in agricultural land use presented an overall increasing trend. 3) The carbon emission reduction effect of the high-standard farmland construction policy in agricultural land use was significant in central China, but non-significant in eastern China and western China.

Background and Objective: There is a paucity of literature comparing unilateral instrumented transforaminal lumbar interbody fusion (UITLIF) with bilateral instrumented TLIF (BITLIF) regarding radiological alignment, including the coronal balance, even though UITLIF might have asymmetric characteristics in the coronal plane. This retrospective study aimed to compare the clinical and long-term radiological outcomes of 1-level UITLIF and BITLIF in lumbar degenerative diseases (LDD). Materials and Methods: Patients who underwent 1-level UITLIF with two rectangular polyetheretherketone (PEEK) cages or BITLIF with ≥ 5 years of follow-up at a single hospital were included. We compared the clinical and radiological outcomes between the UITLIF and BITLIF. Results: In total, 63 and 111 patients who underwent UITLIF and BITLIF, respectively, were enrolled. The median follow-up was 85.55 months (range: 60–130). The UITLIF group had a significantly shorter operation time (185.0 [170.0–210.0] vs. 225.0 [200.0–265.0], p &lt; 0.001) and lower estimated blood loss (300.0 [250.0–500.0] vs. 550.0 [400.0–800.0], p &lt; 0.001) than BITLIF group. Regarding the clinical outcomes, there were no significant differences in the intermittent claudication score (p = 0.495) and Kirkaldy–Willis criteria (p = 0.707) at 1 year postoperatively. The interval changes of the local coronal Cobb angle at the index level, L1-S1 lordotic angle, and coronal off-balance from the immediate postoperative radiograph to the last follow-up were not significantly different (p = 0.687, p = 0.701, and p = 0.367, respectively). Conclusion: UITLIF with two rectangular PEEK cages is a viable option for providing comparable clinical outcomes and radiological longevity to BITLIF in 1-level LDD. In addition, UITLIF has advantages over BITLIF in terms of operative time and blood loss.

This study determines the threshold for the computational rate of actuator motor controllers for unmanned underwater vehicles necessary to accurately follow discontinuous square wave commands. Motors must track challenging square-wave inputs, and identification of key computational rates permit application of deterministic artificial intelligence (D.A.I.) to achieve tracking to a machine-precision degree of accuracy in direct comparison to other state-of-art approaches. All modeling approaches are validated in MATLAB simulations where the motor process is discretized at varying step-sizes (inversely proportional to computational rate). At a large step-size (fast computational rate), discrete D.A.I. shows a mean error more than three times larger than that of a ubiquitous model-following approach. Yet, at a smaller step size (slower computational rate), the mean error decreases by a factor of 10, only three percent larger than that of continuous D.A.I. Hence, the performance of discrete D.A.I. is critically affected by the sampling period for discretization of the system equations and computational rate. Discrete D.A.I. should be avoided when small step-size discretization is unavailable. In fact, continuous D.A.I. has surpassed all modeling approaches which makes it the safest and most viable solution to future commercial applications in unmanned underwater vehicles.

Poly(acrylic acid) (PAAc) hydrogels possess good bioadhesive properties and allow enhanced penetration of drugs. In addition, it is possible to localize the absorption site of the drug in the hydrogel and increase the drug residence time. As opposed to other cross-linking processes radiation-induced polymer cross-linking can be easily and rapidly carried out without the use of cross-linking agents and other chemical additives. In this study, we fabricated metronidazole (MD) containing PAAc hydrogel (MD/PAAc) with different MD contents (0.1, 0.25, 0.5 wt%) using varying radiation doses (25, 50, 75 kGy) by gamma-irradiation. The physical and thermal properties were determined by gel content analysis, swelling ratio measurements, compressive strength measurements, differential scanning calorimetery, and thermogravimetric analysis. The properties of the hydrogel degraded due to the crystalline nature of MD. The properties of the hydrogel degraded due to the crystalline nature of MD. Cumulative release observed after 50 min in the case of 0.5MD/PAAc and 0.1MD/PAAc was 50% and 10%, respectively. Our findings suggest that MD/PAAc could be a suitable drug delivery carrier for use with radiation-based techniques.

This study investigates the impact of specimen size on the mechanical properties of wood, specifically focusing on compression strength, elastic modulus, and Poisson's ratio. Compression tests were conducted using three different specimen sizes (20mm×20mm×30mm, 40mm×40mm×60mm, 60mm×90mm×90mm) in the longitudinal, radial, and tangential directions. Mechanical parameters, failure mechanisms, load-displacement curves, and stress-strain relationships were systematically analyzed for each size. The study also evaluated the influence of specimen size on the accuracy of finite element numerical simulations by utilizing the obtained mechanical parameters. The results reveal a significant correlation between compressive strength and specimen size, indicating a decrease in compressive strength with increasing specimen size. Conversely, elastic modulus and Poisson's ratio exhibit less sensitivity to variations in specimen size. Notably, parameters derived from small-sized specimens (20mm×20mm×30mm) exhibited substantial errors, while those obtained from medium-sized (40mm×40mm×60mm) and large-sized specimens (60mm×90mm×90mm) demonstrated greater reliability, providing precise results in finite element numerical simulations.

Promoting the sustainable development of resource-based cities is of great significance to the ecological protection and high-quality development of the Yellow River Basin. Combining the environmental status and economic development, we objectively evaluate the ecological safety level of resource-based cities in the Yellow River Basin, compare and analysis the main factors affecting the ecological safety of different resource-based cities, and formulate precise and differentiated ecological safety protection measures in river basins to achieve high-quality development. Taking the Yellow River Basin as an example, this paper analyses the ecological level of the Yellow River Basin based on the theory of sustainable development, calculates the ecological safety level of 30 resource-based cities in the Yellow River Basin from 2006 to 2020 by TOPSIS model, and makes convergence analysis by classification. Through the DID empirical test of sustainable development planning policy on ecological safety factors, distinguish the development characteristics of different resource-based cities. The results show that: (1) the ecological safety level of resource-based cities in the Yellow River Basin is generally developing well, and there are differences among different types of resource-based cities; (2) the kinetic energy of sustainable development of resource-based cities in the Yellow River Basin is mainly industrial transformation, and the power of science and technology is insufficient; (3) local governments pay limited attention to environmental protection, and the sustainable development planning of resource-based cities in 2013 mainly promotes the adjustment of industrial structure of resource-based cities.

This paper seeks to model the crack propagation in of AAs (aluminum-alloys) 2524-T3 and 7050-T7452 subjected to fatigue loading at low temperature. Fatigue crack growth tests were performed on AAs 2524-T3 and 7050-T7452 subjected to constant-amplitude and actual random-spectra loading histories at room temperature of about 25 °C and at cryogenic temperature of -70 °C, respectively, to determine their crack growth properties and residual lives. The interaction mechanisms between cryogenic temperature and the fatigue load were deduced on the basis of the results of fractographic analysis. Temperature-dependent residual lives under actual random-spectrum load history were modeled based on a modified accumulation damage rule by accounting for the load interaction. Good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed method.

Emotion plays a powerful role in humans’ interaction with robots. In order to express more human-friendly emotions, robots need the capability of contextual appraisal that expresses the emotional relevance of various targets in the spatiotemporal situation. In this paper, an emotional appraisal methodology is proposed in this study to cope with such contexts. Specifically, the Ortony, Clore, and Collins model is abstracted and simplified to approximate an emotional appraisal model in the form of a sentence-based cognitive system. The contextual emotion appraisal is modeled by formulating the emotional relationships among multiple targets and the emotional transition with events and time passing. To verify the proposed robotic system’s feasibility, simulations were conducted for scenarios where it emotional interacts with humans manipulating liked or disliked objects on a table. This experiment demonstrated that the robot's emotion can variously change over time like human by using a proposed formula for emotional valence, which is moderated by emotion appraisal of occurring events.

In this study, we conducted experiments to assess the forecasting capabilities for the tropical cyclone (TC) genesis over the South China Sea using the ensemble-based data assimilation system (EPS-DA) by WRF-LETKF. These experiments covered forecast lead times of up to 5 days and spanned a period from 2012 to 2019, involving a total of 45 TC formation events. The evaluation involved forecast probability assessments and positional and timing error analysis. Results indicated that successful forecasting depends on lead time and initial condition quality. For TC formation from an embryo vortex to tropical depression intensity, the EPS-DA system demonstrated improved accuracy as the forecast cycle approached the actual formation time. TC centers converged toward observed locations, highlighting the potential of assimilation up to 5 days before formation. We examined statistical variations in dynamic and thermodynamic variables relevant to TC processes, offering an objective system assessment. Our study emphasized early warnings of TC development appear linked to formation-time environmental conditions, particularly strong vorticity and enhanced moisture processes.

This paper discusses the computer-aided (CAD) classification between Hepatocellular Carcinoma (HCC), i.e., the most common type of liver cancer, and Liver Abscess, based on ultrasound image texture features and Support Vector Machine (SVM) classifier. Among 79 cases of liver diseases, with 44 cases of HCC and 35 cases of liver abscess, this research extracts 96 features of Gray-Level Co-occurrence Matrix (GLCM) and Gray-Level Run-Length Matrix (GLRLM) from the region of interests (ROIs) in ultrasound images. Three feature selection models, i) Sequential Forward Selection, ii) Sequential Backward Selection, and iii) F-score, are adopted to determine the identification of these liver diseases. Finally, the developed system can classify HCC and liver abscess by SVM with the accuracy of 88.875%. The proposed methods can provide diagnostic assistance while distinguishing two kinds of liver diseases by using a CAD system.

Coarse-grained molecular dynamics simulations are employed to investigate the spatiotemporal evolution of vesicles (polymersomes) by the self-assembly of randomly distributed amphiphilic BAB triblock copolymers with hydrophilic A and hydrophobic B blocks in an aqueous solution. The vesiculation pathway consists of several intermediate structures, such as an interconnected network of copolymer aggregates, a cage of cylindrical micelles and a lamellar cage. The cage-to-vesicle transition occurs at a constant aggregation number and practically eliminates the hydrophobic interfacial area between the B block and solvent. Molecular reorganization under-lying the sequence of morphology transitions from a cage-like aggregate to a vesicle is nearly isentropic. The end-to-end distances of isolated copolymer chains in solution and those within a vesicular assembly follow log normal probability distributions. This is attributed to the pre-ponderance of folded chain configurations in which the two hydrophobic end groups of a given chain stay close to each other. However, the probability distribution of end-to-end distances is broader for chains within the vesicle as compared to that of a single chain. This is due to the swelling of the folded configurations within the hydrophobic bilayer. Increasing the hydropho-bicity of the B block reduces the vesiculation time without qualitatively altering the self-assembly pathway.

Activities in the digital economy driven by information technology have rapidly increased in scope and speed in the aftermath of COVID-19. Meanwhile, social isolation accelerated by quarantine measures has increased concerns about individuals’ mental health. However, little is known about the specific consequences of online interactions, especially when applied in online fan community-based relationships where loyal community members are prevalent. Therefore, we examined whether a sense of virtual community (SOVC) can link fans’ online activities with their mental well-being and behavioral loyalty to the platform. For this purpose, we focus on BTS fandom “Adorable Representative MC for Youth” (ARMY) behaviors and attitudes on the fan community platform Weverse. With 202 valid data samples acquired from global ARMY, this study conducted a partial least squares–structural equation modeling analysis. The empirical findings reveal that SOVC in Weverse is significantly influenced by the intensity of online interactions with other fans and parasocial relationships with celebrities. SOVC is found to be the direct predictor of fans’ behavioral loyalty and mental well-being. When considering fans’ perceptions of other social media platforms, dissatisfaction with previous online fan communities enhances the intensity of online interactions with other fans in Weverse.

(1) Background: The CEO message of hospital homepage contain various contents such as the hospital's future vision, promises with customers, upgraded services and public activities. The CEO’s message of the homepage includes non-financial information as well as financial information of corporates. Also, it provides useful information for not only company's goals and vision but also firm performance and strategies for the future. This study aims to investigate associations between CEO’s message of hospitals homepages and financial status. We used the balanced scorecard frame to analyze what content on the hospital's homepage is related to the hospital's various financial ratios. (2) Methods: We adopt a text mining method to extract significantly repeated keywords from the CEO’s message of hospital website. And we classify these keywords by a balanced scorecard frame. To examine the relationship between keywords of CEO’s message of the hospital homepage and hospital’s financial ratio, T-test is conducted for the difference in the TF-IDF (Term Frequency is Divided by Inverse Document Frequency) mean of the home page contents and its relationship with the views of the balanced scorecard framework. (3) Results: According to empirical results on 65 samples collected from local hospitals, there are some significant relationship between the qualitative content of the hospital's homepage and the quantitative financial ratio that indicates profitability, activity, leverage, liquidity, and transfer to essential business fund (EBF) income. (4) Conclusions: The introduction section of a homepage is most accessible to customers, containing the aims and ideals of hospitals and reflecting their values and visions [1]. In addition, in view of financial status, they can either emphasize financial strength or focus on other areas to mask weakness of financial information. This study reminds us of the importance of hospital website’s disclosure, and it can be inferred from the financial status of the hospital. It also highlights the need for harmonization between quantitative data, financial statements, and qualitative data, CEO’s messages. (5) Implications: To our best knowledge, this paper is the first research attempting to investigate the relation between text of hospital homepage and financial ratio of hospital through text mining technique and balanced scorecard frame. Hospitals take a crucial part in a country’s welfare and healthcare backbone industry. Nevertheless, in many countries, hospital organization sectors tend to remain a source of critical fiscal deficits due to its ineffective and sloppy management. We expect that the result of this paper can provide hospital managers to useful information.

The undoped and tungsten (W)-doped vanadium dioxide (VO₂) thin films were prepared by electron beam evaporation associated with ion-beam assisted deposition (IAD). The influence of different W-doped contents (3%-5%) on the optical, electrical, structural, and thermos-mechanical properties of VO₂ thin films was investigated experimentally. Spectral transmittance results showed that with the increase of W-doped contents, the transmittance in the visible light range (400-750 nm) decreases from 60.2% to 53.9%, and the transmittance in the infrared wavelength range (2.5 μm to 5.5 μm) drops from 55.8% to 15.4%. As the W-doped content increases, the residual stress in the VO₂ thin film decreases from -0.276 GPa to -0.238 GPa, but the surface roughness increases. For temperature-dependent spectroscopic measurements, heating the VO2 thin films from 30°C to 100°C showed the most significant change in transmittance for the 5% W-doped VO₂ thin film. When the heating temperature exceeds 55°C, the optical transmittance drops significantly, and the visible light transmittance drops by about 11%. Finally, X-ray Diffraction (XRD) and scanning electron microscope (SEM) were used to evaluate the microstructure characteristics of VO₂ thin films.

This work emphasizes to use silver decorative method to enhance the antibacterial activity of TiO₂ and ZnO nanoparticles. These silver decorated nanoparticles (hybrid nanoparticles) were synthesized by using sodium borohydride as a reducing agent, with the weight ratio of Ag precursors: oxide nanoparticles = 1: 30. The morphology and optical property of these hybrid nanoparticles were investigated using transmission electron microscopy (TEM) and UV–vis spectroscopy. The agar-well diffusion method was used to evaluate their antibacterial activity against both Staphylococcus aureus and Escherichia coli bacteria, with or without light irradiation. The TEM images indicated clearly that silver nanoparticles (AgNPs, 5-10 nm) were well deposited on the surface of nano-TiO₂ particles (30-60 nm). Besides, smaller AgNPs (< 2 nm) were dispersed on the surface of nano-ZnO particles (20-50 nm). UV-vis spectra confirmed that the hybridization of Ag and oxide nanoparticles led to shift the absorption edge of oxide nanoparticles to the lower energy region (visible region). The antibacterial tests indicated that both oxide pure nanoparticles did not exhibit inhibitory against bacteria, with or without light irradiation. However, the presence of AgNPs in their hybrids, even at low content (< 40 mg/mL) leads to a good antibacterial activity and the higher inhibition zones under light irradiation as compared to that in dark was observed.

Osteoarthritis (OA) is the degeneration of cartilage in joints that results in bones rubbing against each other, it causes uncomfortable symptoms such as pain, swelling, stiffness, and can lead to disability. It usually occurs in the elderly and causes a large medical burden. The aim of this study is to evaluate cost-effectiveness between the standard treatment for osteoarthritis and the standard treatment with added crystalline glucosamine sulfate at various stages. The Markov analysis modelling was applied to evaluate the effect of both adding glucosamine compared to standard treatment from a societal perspective during whole patients’ lifetimes. Data input was collected by review in previous studies. The outcome was measured in quality-adjusted life years (QALYs), and the incremental cost-effectiveness ratio (ICER) from a societal perspective was ap-plied with 3%-discounted for all cost and outcome. One-way analysis via Tornado diagram was performed to investigate the change of factors in model. In general, the adding glucosamine into the standard treatment proved to be more cost-effectiveness compared to the standard treatment. Particularly, early stage adding glucosamine in the treatment was cost-effectiveness then post-stage adding glucosamine. The addition of supplementing crystalline glucosamine sulfate to whole regimen at any stage was cost-effectiveness at willingness-to-pay (WTP) threshold

In this study, a new empirical equation was established to predict the sedimentation volume resulting from the construction of a multipurpose weir or low-head dam. The study employed a one-dimensional numerical model (STAFF) to investigate the key parameters affecting sedimentation volume. Short-term predictions were conducted through laboratory experiments with movable bed, and the results indicated that dimensionless unit stream power and the Shields parameter exhibited the most significant correlation with dimensionless deposition volume. Using a multiple regression approach, an empirical equation was formulated and validated for predicting sedimentation in the upstream reservoir of the weir.

Gain-scheduled autopilots have emerged as a dominant strategy to achieve adaptive control of coupled, non-linear engineering complexities, owing to an ability to adapt to changing operational conditions and uncertainties. This study focuses on utilizing bilinear interpolation of gain-scheduled autopilots, emphasizing enhanced system performance and robustness. Through a comprehensive investigation and comparative analysis using three disparate cases, advantages over conventional methods are revealed. Strengths and weaknesses of both simple and specialized variants (such as linear, and real-time gain-scheduling) are introduced. Three missile guidance case–studies utilize simulation time and miss distance figures of merit. Potential to achieve precise control across various mission scenarios, while ensuring reduced computational complexity is revealed by nearly two–hundred percent improved missile miss distances with comparable distances traveled and slightly improved computational burden.

This research intended to report amine-functionalized multiwall carbon nanotubes (MWCNTs) prepared by a simple method for efficient and rapid removal of Reactive Yellow 2 (RY2) from water. EDS analysis showed that the N content increased from 0 to 2.42% and from 2.42 to 8.66% after modification by APTES and PEI, respectively. BET analysis displayed that the specific surface area, average pore size, and total pore volume were reduced from 405.22 to 176.16 m2/g, 39.67 to 6.30 nm, and 4.02 to 0.28 cm3/g, respectively. These results proved that the PEI/APTES-MWCNTs were successfully prepared. pH edge experiment indicated that pH 2 was optimal for RY2 removal. At pH 2 and 25 °C, the time required for adsorption equilibrium was 10, 15, and 180 min at initial concentrations of 50, 100, and 200 mg/L, respectively; and the maximum RY2 uptake calculated by the Langmuir model was 714.29 mg/g. Thermodynamic studies revealed that the adsorption process was spontaneous and endothermic. 0-0.1 mol/L of NaCl showed negligible effect on RY2 removal by PEI/APTES-MWCNTs. Five adsorption/desorption cycles confirmed the good reusability of PEI/APTES-MWCNTs in RY2 removal. Overall, the PEI/APTES-MWCNTs are a potential and efficient adsorbent for reactive dye wastewater treatment.

In this study, a tuned mass damper is proposed as a seismic acceleration mitigating technique of an electrical cabinet inside the nuclear power plant. In order to know the mitigation performance, the electrical cabinet and the tuned mass damper were modeled using SAP2000. The sine sweep wave was used to confirm the vibration characteristics of the cabinet over a wide frequency range, and the several various earthquakes were applied to the cabinet to verify the control performance of the tuned mass damper. After analyzing the numerical results, it is summarized that the application of the proposed technique can reduce the acceleration response of the cabinet.

TVs and monitors are among the most widely used displays in various environments. However, they have limitations in their physical display conditions, such as a fixed size/position and a rigid/flat space. In this paper, we suggest a new "Display In the Wild" (DIW) concept to overcome the aforementioned problems. Our proposed DIW system allows us to display a flexibly large screen on dynamic non-planar surfaces at an arbitrary display position. To implement our DIW concept practically, we choose a projector as the hardware configuration in order to a generate screen anywhere with different sizes. However, distortion occurs when the projector displays content on a surface that is dynamic and/or non-planar. Therefore, we propose a distortion correction method for DIW to overcome the aforementioned surface-constraints. Since projectors are not capture devices, we propose using a depth camera to determine the distortions on the surfaces quickly. We also propose DIW-specific calibration and fast/precise correction methods. Our calibration method is constructed to easily and quickly detect the projection surface, and also allows our proposed system to accommodate the intrinsic parameters such as a display resolution and field of view. We accomplish a fast undistortion process of the projector by considering only surface boundary pixels, which enables our method to run in real time. In our comprehensive experiments, the proposed DIW system generates undistorted screens such as TVs and monitors on dynamic non-planar surfaces at an arbitrary display position with Unmanned Aerial Vehicles (UAVs) in a fast and accurate manner, demonstrating its usefullness in practical DIW scenarios.

This paper mainly explores the feasibility of using desert sand (DS) and recycled aggregate in cement stabilized base. Recycled coarse aggregate (RCA) and DS serve as the substitutes of natural coarse and fine aggregates, respectively, in cement stabilized base. A four-factor and four-level orthogonal test is designed to analyze the unconfined compressive strength, splitting tensile strength, and compressive resilient modulus. Furthermore, this paper investigates the effects of cement content, fly ash (FA) replacement rate, RCA replacement rate, and DS replacement rate on the road performance of cement stabilized base composing of RCA and DS. The test results reveal that the performance of cement stabilized base with partial RCA instead of natural coarse aggregate (NCA) and partial DS instead of natural fine aggregate satisfy the road use. Meanwhile, DS is beneficial to improve the strength of cement stabilized base. The correlation and microscopic analyses of the test results imply the feasibility of applying DS and recycled aggregate to cement stabilized base. It is hoped that this paper can offer a solid theoretical foundation for promoting the application of DS and recycled aggregate in road engineering.

Domain generalization has led to remarkable achievements in Hyperspectral Image (HSI) classification. Inspired by contrastive language-image pre-training (CLIP), the language-aware domain generalization method has been explored to learn cross-domain-invariant representation. However, existing methods face some challenges: 1) The weak capacity to extract long-range contextual information and inter-class correlation. 2) Due to the inadequacies of the large-scale pre-training for HSI data, the spatial-spectral features of HSI and linguistic features can not be straightforwardly alignment. To address the above problems, a novel network has been proposed with a CLIP framework, which consists of an image encoder, based on an encoder-only transformer to obtain the global contextual information and inter-class correlation, a frozen text encoder, and a cross-attention mechanism, named Linguistic-Interact-with-Visual Engager (LIVE), enhances the interaction between two modalities. Extensive experiments demonstrating superior performance over state-of-the-art methods in HSI Domain Generalization with a CLIP framework.

Eco-innovation denotes developing green practices using environmentally friendly innovative approaches or technologies. Although, eco-innovation has been broadly applied in different in-dustries, such as low-carbon production and manufacturing, how to implement such innovation in education for sustainable development (ESD) has rarely been studied. Therefore, this research considered a reflective and cooperative learning approach to science, technology, engineering, arts, and math (STEAM) education. A case study examined Wanluan Township of Pingtung County in southern Taiwan. Four departments’ students and teachers at Meiho University were involved in situated learning. Students of hospitality management played farm owners who en-gaged in organic agriculture to produce food and beverages. These agricultural products were farm-to-table, cooked and served for customers in a natural dining setting through the students’ teamwork. Students of tourism, sports & leisure management, and food science & nutrition played tourists in a self-guided travel context, who engaged in acts such as visiting buildings to understand heritage while observing that the houses were still in use a dwelling. This encouraged reflection on the importance of cultural preservation. According to the results from the role-play farm owners and tourists, eco-innovation can represent a sustainable marketing strategy for im-proving the local-community economy and can be implemented in a practical situation in STEAM. The goal of ESD for 2030 — societal transformation — is to foster students’ responsible behavior and attitudes in a personally authentic manner, thereby fostering sustainability learning and understanding.

Currently, Korea is experiencing localized extreme rainfall, which accounts for more than 80% of flood-related disasters, and is increasing in small river basins, where more than 60% of flood-related casualties occur. These events are caused by climate change and geological factors and their impact is becoming more severe. As a result, an effective measurement system is required to mitigate their impact, particularly in small stream basins that are especially vulnerable due to their steep slopes, small catchment areas, and lack of maintenance and management capacity. In addition, a Flood Early Warning Framework (FEWF) that forecasts discharge and depth during flood events is crucial for reducing casualties. Therefore, this research is focused on developing the FEWF using the nomograph and rating curve methods, which are established by the robust constrained nonlinear equation solver and are suitable for small streams. The FEWF is evaluated using real-time data observed over 7-years period from the Closed-circuit Television-based Automatic Discharge Measurement Technology (CADMT), and the results show that the FEWF is effective in forecasting discharge and depth during flood events. The use of CADMT technology for real-time data can develop an accurate and reliable FEWF, which can help mitigate the impacts of extreme rainfall events and reduce the number of flood-related casualties in small stream basins.

To ensure consumers can purchase high-quality rice, accurate identification of rice varieties is particularly important. Methods: This article conducts research based on machine learning algorithms from the perspectives of image, spectrum, and spectrogram fusion. Six types of hyperspectral image data of rice were preprocessed using convolutional smoothing (SG) and multiple scatter correction (MSC). Texture information of the images was extracted using gray-level co-occurrence matrix. Spectra, texture, and spectrogram data were fused into a new matrix. Spectral, texture, and spectrogram fusion data were used as inputs for the model, and support vector machines (SVM), logistic regression (LR), and K-nearest neighbors (KNN) classification models were constructed and compared. Results: From the classification results, the spectrogram fusion classification performance was better than classification models using only spectra or texture. Conclusion: The research results showed that the accuracy of SVM and LR classification models exceeded 90%, and the LR model performed the best, effectively classifying rice varieties.

This study compared condylar volume, length, and articular eminence (AE) characteristics in normal individuals and those with unilateral and bilateral juvenile idiopathic osteoarthritis (JOA). The 116 patients were divided into four groups: control (n=16), affected condyle of unilateral JOA (Aff-Uni) (n=36), non-affected condyle of JOA (NonAff-uni) (n=36), and bilateral JOA (Bi-JOA) (n=28). Volume and length differences in the condyle and AE were analyzed using ANOVA and Bonferroni post hoc tests. The results showed that Bi-JOA had significantly different condylar volume, especially in the condylar head (p&lt;0.01), specifically the middle, anterior, and medial parts (p&lt;0.05). Condylar length also differed among the groups, with differences observed between the control group and the other three groups, as well as between the bilateral group and the other three groups (p&lt;0.01). AE total volume differed between the control group and Aff-Uni. In the detailed comparison, Aff-Uni and NonAff-Uni were smaller than the control group in the posterior, lateral, and medial sections (p&lt;0.05). In conclusion, depending on the involvement of unilateral or bilateral JOA, there were differences in condylar volume and AE compared to the normal control group. Therefore, prognosis should be evaluated by distinguishing between patients with unilateral and bilateral JOA.

Individual investors often struggle to predict stock prices due to the limitations imposed by the computational capacities of personal laptop Graphics Processing Units (GPUs) when running intensive deep learning models. This study proposes solving these GPU constraints by integrating deep learning models with technical analysis methods. This integration significantly reduces analysis time and equips individual investors with the ability to identify stocks that may yield potential gains or losses in an efficient manner. Thus, a comprehensive buy and sell algorithm, compatible with average laptop GPU performance, is introduced in the study. This algorithm offers a lightweight analysis method that emphasizes factors identified by technical analysis methods, thereby providing a more accessible and efficient approach for individual investors. To evaluate the efficacy of this approach, we analyzed the performance of eight deep learning models: LSTM (4 layers), CNN, BiLSTM (4 layers), CNN Attention, BiGRU CNN BiLSTM Attention, BiLSTM Attention CNN, CNN BiLSTM Attention, and CNN Attention BiLSTM. These models were used to predict stock prices for Samsung Electronics and Celltrion Healthcare. The CNN Attention BiLSTM model displayed superior performance among these models, with the lowest validation mean absolute error value. In addition, an experiment was conducted using WandB Sweep to determine the optimal hyperparameters for four individual hybrid models. These optimal parameters were then implemented in each model to validate their back-testing rate of return. The CNN Attention BiLSTM hybrid model emerged as the highest-performing model, achieving an approximate rate of return of 5 percent. Overall, this study offers valuable insights into the performance of various deep learning and hybrid models in predicting stock prices. These findings can assist individual investors in selecting appropriate models that align with their investment strategies, thereby increasing their likelihood of success in the stock market.

The purpose of this paper is to summarize and share the field experiment results of KEPCO's project consortium to create a TSO-DSO-DERA interaction scheme. The field experiment was conducted based on the prequalification algorithm proposed in the previous research from the same consortium and was designed to verify the validity of the algorithm under realistic grid conditions. In addition, during the course of the field experiment, it was found that points that were missed or not given much importance in the existing prequalification algorithm could affect the completeness of the overall system, and then practical improvements were made to improve it. The demonstration results confirm that the proposed algorithm is effective in real-world grid environments and can help DSOs ensure the reliability of the distribution system while supporting DERA's participation in the wholesale market using the proposed prequalification scheme.

In this work, alkylammonium-functionalized hollow mesoporous silica as nonocarrier of drugs was synthesized to realize enhanced cancer therapy by pH stimuli for sustained drug release. First, functionalized hollow mesoporous silica nanoparticles (Hollow MSNs) were synthesized using dodecyl dimethyl(3-sulfopropyl)ammonium hydroxide (DDAPS), sodium dodecyl sulfate (SDS), and triethanolamine as structure-directing agents, and tetraethyl orthosilicate (TEOS) and N-trimethoxysilypropyl-N,N,N-trimethylammonium chloride (TMAPS) as silica sources under basic condition via the sol-gel process. The structure and morphology of the alkylammonium-functionalized hollow mesoporous silica nanoparticles (Hollow MSN-N+CH3) were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), N2 adsorption-desorption analysis, and Fourier-transform infrared (FT-IR) spectroscopy. The functionalized hollow MSNs had a particle size of about 450 nm and a shell thickness of about 60 nm with uniform size. The nanoparticle had a surface area of 408 m2g-1, pore volume of 0.8 cm3g-1 and a uniform pore diameter of 45.9 Å. In the cancer cell viability test with MCF-7 cell, fludarabine-incorporated and alkylammonium-functionalized hollow mesoporous silica nanoparticles (Flu/Hollow MSN-N+CH3) showed excellent cancer cell death comparable with pure fludarabine drug with the controlled drug release by pH stimuli. It is considered that our current materials have the potential applicability as pH-responsive nanocarriers in the field of cancer therapy.

Marine vessels operating on the Arctic Sea route are constantly prone to collisions and friction with ice. This study discusses the wear of the hull plate caused by the collision of ice against vessels operating in Arctic Sea routes. The abrasive wear of the hull due to ice impact was numerically assessed based on both the incident behavior of ice particles interacting with the flow around the hull and the wear loss of the hull surface caused by the contact force of ice particles. A multi-phase approach was adopted to account for the behavior of ice particles continuously affected by the fluid force around the hull. The fluid force acting on the ice floe was evaluated using computational fluid dynamics (CFD) and the dynamic motion of the drift ice was evaluated using the discrete element method (DEM). The motion of the floating ice particles was updated in real time by iteratively coupling the fluid force and the motion of the ice floe at each time step of the numerical simulation. The results of the wear simulation models were presented in terms of the shape change of the hull surface due to wear. At first, the wear was evaluated for cases in which only the surface paint of the hull was damaged. Thereafter, a computation model considering the shape change of the hull surface experiencing long-term friction of ice particles was introduced. Finally, the numerical procedures to predict the abrasive wear of the hull surface by ice impact were discussed.

Current-voltage characteristics curves of NFinFET are presented and are fitted with the modi-fied current-voltage (I-V) formulas, where the modified term in the triode region is demon-strated to be indispensable. In the as-known I-V formula, important parameters need determin-ing to make both the measured data and the fitting data as close as possible. Those parameters include kN (associated with the sizes of the transistor and mobility), (associated with Early Voltage), and Vth (the threshold voltage). The differences between the measured data and the fit-ting data vary as the applied source-drain bias, proving that the mobility of the carriers is not consistently constant. On the other hand, a modified formula, called kink effect factor, is nega-tively or positively added simulating solitary heat waves, which disturb the propagation of car-riers and thus influence the Source-Drain current (IDS). The new statistical standard deviations () are then found to be effectively suppressed as the kink effect is taken into account.

We propose an algorithm for generating a panoramic image of a pipe’s inner surface based on inverse perspective mapping (IPM). For efficient crack detection, we used only perspective images of the pipe interior that can be obtained with a single lens camera instead of those taken with a 360-degree camera or a 3D depth camera. Frontal images taken while passing through the pipe were converted to images of the inner surface of the pipe using IPM. We derived a generalized IPM formula that considers the slope of the image plane to correct image distortion caused by the tilt of the plane; this IPM formula was derived based on the vanishing point of the perspective image, which was detected using optical flow techniques. Finally, the multiple transformed images with overlapping areas were combined via image stitching to create a panoramic image of the inner pipe surface. To validate our proposed algorithm, we restored images of pipe inner surface using a 3D pipe model and used these images for crack detection.

A flexible structure is applied to improve the lubrication performance of a misaligned journal bearing. The journal bearing is representative sliding bearing and there are damages due to metal-to-metal contact by misalignment. Since misalignment is an unavoidable phenomenon, a journal bearing with a flexible structure was proposed as a way to improve it. The lubrication characteristics of the bearing are evaluated numerically under steady-state condition. EHL (elastohydrodynamic lubrication) analysis considering elastic deformation was performed. The lubrication performance is compared in accordance with variation of the geometry of the flexible structure and evaluated based on the minimum film thickness. Moreover, the results of the journal bearing with flexible structure are compared with those of the journal bearing without the flexible structure. The flexible structure is then applied in the form of a groove to the area supporting high load on the journal bearing; it is elastically deformed by the generated oil-film pressure, which helps to obscure a larger oil film. Through numerical analysis, it is found that the journal bearing with flexible structure can improve the lubrication performance in the misaligned condition.

(1) Background: Due to the high proportion of disadvantaged students in a rural school in Taiwan and the gap between students’ concepts and practices of environmental protection and sustainable energy, four science and mathematics teachers in this school planned an engineering-centered PjBL of sustainable energy curriculum in a Makers Club to enhance students’ creativity, engineering skills, practices of environmental protection and sustainable energy, and learning attitudes; (2) Methods: This study is four-year action research. Teachers and students initiated the idea from rebuilding an old fan in a classroom; (3) Results: The students in the Makers Club improved their engineering skills and created various green-power generation devices (evolved from ventilation ball generator, hydropower, ocean current power generators to tiny, 3D-printing wind power generators). They turned environmental protection and sustainable energy concepts into actions during practices and won awards from science and engineering fairs every year. This creative and supportive atmosphere spread from the club to the whole school and improved the students’ practices of environmental protection and learning attitudes after long-term implementation; (4) Conclusions: The design principles of the engineering-centered PjBL of sustainable energy curriculum played a critical role and were outlined at the end of the study.