Enzymatic degradation of organic pollutants is a new and promising remediation approach. Peroxidases are one of the most commonly used classes of enzymes to degrade organic pollutants. However, it is generally assumed that all peroxidases behave similarly and produce similar degradation products. In this study, we conducted detailed studies of the degradation of a model aromatic pollutant, Sulforhodamine B dye (SRB dye), using two peroxidases—soybean peroxidase (SBP) and chloroperoxidase (CPO). Our results show that these two related enzymes had different optimum conditions (pH, temperature, H₂O₂ concentration...etc.) for efficiently degrading SRB dye. High-performance liquid chromatography and LC-mass spectrometry analyses confirmed that both SBP and CPO transformed the SRB dye into low molecular weight intermediates. While most of the intermediates produced by the two enzymes were the same, the CPO treatment produced at least one different intermediate. Furthermore, toxicological evaluation using lettuce (Lactuca sativa) seeds demonstrated that the SBP-based treatment was able to eliminate the phytotoxicity of SRB dye, but the CPO-based treatment did not. Our results show, for the first time, that while both of these related enzymes can be used to efficiently degrade organic pollutants, they have different optimum reaction conditions and may not be equally efficient in detoxification of organic pollutants.

For a graph G, let P(G, λ) be its chromatic polynomial. Two graphs G and H are said to be chromatically equivalent if P(G,λ) = P(H,λ). A graph is said to be chromatically unique if no other graph shares its chromatic polynomial. In this paper, chromatic polynomial of the necklace graph N_n, for n ≥ 2 has been determined. It is further shown that N₃ is chromatically unique.

Few switching transitions in high power and medium voltage application of Power converters are desirable. The selective harmonics elimination (SHE) pulse width modulation offers a better quality waveform with lower switching transitions and hence lower switching losses. The SHE is a pre-programmed modulation technique where certain amounts of lower order harmonics are removed and fundamental voltage is controlled. After Fourier analysis of output waveform, a set of nonlinear transcendental equations is obtained which exhibits, multiple, unique or no solution in different range of modulation index (MI). In this paper, an iterative method based on the Jacobian estimate is proposed to solve a highly non-linear set of SHE equations. The proposed technique is easy in implementation and can solve a large number of such equations as computation of the Jacobian matrix in the subsequent iteration is estimated from the previous values. Moreover, the proposed method also removes the singularity problem, especially for large SHE equations. High accuracy in the initial guess is also not essential for this method and can converge to the solution with any random initial guess. The computational and simulation results are given to validate the concept. The hardware result is provided to confirm the computational and simulation results.

Objective: To investigate social, economic, and environmental contributors to quit or continue smoking and vaping during the COVID-19 pandemic. Methods: A qualitative study design was adopted to identify smokers’ beliefs in a LMIC, using a small community sample. Results: 276 participants were primarily surveyed. Motivation to continue smoking included temporary pleasurable effects, working remotely, stress or anxiety, whereas a motivator to quit smoking was the overlap with COVID-19 symptomatology. There was a rise in social awareness regarding the potential harm of smoking and vaping during the pandemic yet those participants who were younger felt they were immune from its morbid complications. Conclusions: With paradoxical associations of COVID-19 with cigarette and vape usage, it is important to pay attention to biases in data in favor of educating its users of the increased risk of severe disease.

Aim: To investigate the application of anterior and posterior corneal higher order aberrations (HOAs) in detecting keratoconus (KC) and suspect keratoconus (SKC). Method: This is a retrospective, case-control study which evaluated non-ectatic (normal) eyes, SKC eyes, and KC eyes. The Sirius Scheimpfug (CSO, Italy) analyzer was used to measure HOAs of the anterior and posterior corneal surfaces. Sensitivity, specificity and area under receiver operating characteristic curve (AUC) were calculated. Results: Two-hundred and twenty eyes were included in the analysis (normal n = 108, SKC n= 42, KC n= 70). Receiver operating characteristic (ROC) curve analysis revealed a high predictive ability for anterior corneal HOAs parameters: Root mean square (RMS) total corneal HOAs, RMS trefoil and RMS coma to detect keratoconus (AUC > 0.9 for all). RMS Coma (3, ±1) derived from the anterior corneal surface was the parameter with the highest ability to discriminate between suspect keratoconus and normal eyes (AUC = 0.922; cutoff > 0.2). All posterior corneal HOAs parameters were insufficient in discriminating between SKC and normal eyes (AUC < 0.8 for all). In contrast, their ability to detect KC was excellent with AUC of > 0.9 for all except RMS spherical aberrations (AUC = 0.846). Conclusion: Anterior and posterior corneal higher order aberrations can differentiate between keratoconus and normal eyes, with a high level of certainty. In suspect keratoconus disease however, only anterior corneal HOAs, and in particular coma-like aberrations, are of value. Corneal aberrometry may be of value in screening for keratoconus in populations with a high prevalence of the disease.

This study addresses the pressing energy constraints in nations like Bangladesh by proposing the implementation of photovoltaic (PV) microgrids. Given concerns about environmental degrada-tion, limited fossil fuel reserves, and volatile product costs, renewable energy sources are gaining momentum globally. Our research focuses on a grid-connected solar PV system model at Char Jazira, Lalpur, Natore, Rajshahi, Bangladesh. Through PVsyst simulation software, we assess the performance ratio (PR) and system losses, revealing an annual solar energy potential of 3375 MWh at Standard Test Condition (STC) efficiency. After considering losses, the system generates 2815 MWh annually, with 2774 MWh exported to the grid. We analyze an average PR of 78.63% and calculate a levelized cost of energy (LCOE) of 2.82 BDT/kWh [1 USD = 110 BDT]. The financial assessment indicates a cost-effective LCOE for the grid-connected PV system, with an annual gross income of 27744 BDT from selling energy to the grid and operating costs of 64060.60 BDT/year. Remarkably, this initiative can prevent 33074.061 tCO2 emissions over the project’s 25-year lifespan.

Background: Women in rural districts of Pakistan face numerous barriers to healthcare, rendering gender-responsive health programming important, including for Tuberculosis (TB). This study was conducted to assess the general understanding of TB and of access to healthcare for women, as a first step towards implementation of a gender responsive TB programme in TandoAllayar, a rural district of Pakistan. Methods: A total of 36 participants were interviewed. The focus group discussion guide comprised of questions on: (1) family/household dynamics (2) community norms (3) healthcare system (4) women’s access to healthcare (5) TB Awareness;, and (6) women’s access to TB Care. Results: Limited autonomy in household financial decision-making, disapproval of unassisted travel, long travel time, lack of prioritization of spending on women’s health and inadequate presence of female health providers, were identified as barriers to access of healthcare for women, higher in younger women. Facilitators to access of TB care included a reported lack of TB-related stigma, moderate knowledge about TB disease, and broad understanding of tuberculosis as a curable disease. Other suggested facilitators include health facilities closer to the villages and the availability of higher quality services. Conclusion: Significant barriers are faced by women in access to TB care in rural districts of Pakistan. Programme implementers in high burden countries, should shift towards improved gender-responsive TB programming.

The fish found in the Tibetan Plateau and the Himalayas are referred to as schizothoracids, and they have evolved unique biological adaptations to high elevations. These adaptations include changes in the shape of the mouth, size, and length of gill rakers according to the prey size, sucking attachment organs to cope with fast currents, and genetic differences due to hypoxia and UV light. Nevertheless, there are recent threats like destruction of natural habitats, pollution, overfishing, and global warming that have posed serious conservation issues for numerous species. Conservation measures have been initiated even though well-articulated management techniques or other protective measures are absent from several protected areas for freshwater fisheries located in India. To resolve these issues, Schizothoracid population rescue, rehabilitation and restocking in safe water bodies should be implemented. For achieving their sustainability, scientists, conservationists, and legislators need to coordinate with each other.

Climate risk is one of the confronting factors in Indian agriculture. To overcome this distrust, a large number of sensors can be installed in the fields,The extensive IoT platform can process the data sent by these sensors.The Data stream can be processed in real-timeusing Fuzzylogic, to offer smart solution. Network coding can enhance throughput and security. Thus reducing human interaction and improve efficiency.

Globally, the fuel demand is increasing rapidly and the conventional method to produce fuel is toxic which causes environmental degradation and climate crisis. Therefore, biodiesel emerges as the substitute to overcome the conventional fuel problems because biodiesel is renewable and non-toxic. Biodiesel synthesis is the process of using fats and oils to produce biodiesel ester and glycerol. Biodiesel can be produced using edible and non-edible feedstock but using the edible feedstocks problems like fuel vs food, nutritional value and economic considerations were raised. Therefore, non-edible feedstocks are being used to overcome problems arising from edible feedstock. As non-edible feedstocks can easily be grown anywhere on land, doesn’t cause imbalance to food economy and has low cost. Many non-consumable seeds like Mahua, Jatropha, Castor, Neem etc. are used to produce biodiesel. Now a days, researchers are using nanoparticles to enhance the stability, quality, and properties of biodiesel. In future, researchers can use algae and microbial oils for production of biodiesel. Research can also use biojet fuel in such a way that it reduces the carbon emission. In future, production of biodiesel can be integrated into circular economy models to reduce environmental waste and impact. In this review we will discuss the production methods for biodiesel, catalysts for biodiesel production, and non-edible feedstock properties of biodiesel.

Climate risk is one of the confronting factors in Indian agriculture. To overcome this distrust, a large number of sensors can be installed in the fields,The extensive IoT platform can process the data sent by these sensors.The Data stream can be processed in real-timeusing Fuzzylogic, to offer smart solution. Network coding can enhance throughput and security. Thus reducing human interaction and improve efficiency.

In archaea, the interaction of HerA helicase and NurA nuclease is required for 3' end resection during DNA double-stranded break repair, and its disruption results in unfaithful DNA repair. Interactions transpire by the four conserved domains, including the N-terminal HAS domain (HerA-ATP synthase), which serves as a binding site for the exonuclease NurA. As a HerA hexamer between its two subunits, the conserved C-terminal brace extension functions as an adjacent brace. DBD serves as a location for DNA binding, which causes the DNA strands to be propelled into the HerA pocket to begin unwinding. The putative pore entrance is made up of four helix coils, which provide a suitable charged surface for guiding DNA into the pore. The crystal structure of the complex HerA-NurA allows for the identification of key residues for protein-protein interaction. This allows us to predict that most archaeal HerA orthologs will be able to interact with one another. Archaeal HerA is a homo-hexameric assembly featuring a DNA-binding domain that is conserved. It also features distinctive ATP and NurA binding domains. Following the structure and sequence conservation criteria, we find one HerA ortholog in Pyrobaculum calidifontis and multiple HerA paralogs, but the role of none is established yet.Interestingly, orthologous HerA is part of an Mre11-Rad50 gene neighborhood while paralogous HerA is not, which could be misleading. As a result, it sought to describe the criteria that may be used as a possible fingerprint for identifying orthologous genes, as well as the cloning procedures and tactics that would aid in the confirmation of the HerA helicase in P. calidifontis. Their confirmation is based on PCR cloning and characterization following HerA construct creation.

Applications for Wireless Sensor Networks (WSNs) range from monitoring the environment to automating factories. However, sustained and effective functioning is made more difficult by Sensor Nodes (SNs) limited energy supplies in which optimization is the main issue. So with the aim of increasing the lifespan by decreasing the energy consumption of WSN, Low-Energy Adaptive Clustering Hierarchy (LEACH) protocol with Deep Learning (DL) algorithm is analyzed in this paper. LEACH is a hierarchical mechanism that elects Cluster Heads (CHs) and regularly rotates their positions in order to allocate energy use effectively by using the same amount of energy. However, Deep Learning (DL) method is used to further improve energy optimization. In many applications, the types of Deep Learning methods like Artificial Neural Networks (ANNs) have shown to be very useful. Using this method, WSNs may make more efficient decisions that reduce energy consumption. Data aggregation, duty cycling, and transmission protocols may all be optimized by Deep Learning model's ability to recognize patterns and forecast network behavior. This results in lower energy consumption, a longer lifespan for the network, and better overall performance.

This review paper explores auditory tactile (AT) synesthesia, a rare neurological condition where sounds evoke tactile sensations. The paper provides a historical overview of the condition and discusses its epidemiology, with a prevalence of less than 1% of the general population. The neurological basis of AT synesthesia is explored, including the role of cross-modal processing and hyperconnectivity within the brain. The paper also describes the phenomenology of the condition, including the range of tactile sensations that can be experienced in response to different sounds. The occurrence of AT synesthesia in the present-day world is discussed, including its relationship to music and art. Various hypotheses surrounding the development and maintenance of AT synesthesia are reviewed, focusing on genetic and environmental factors. The implications for clinical practice are explored, including potential benefits for individuals with sensory processing disorders. Finally, the paper concludes with a discussion of future directions for research in this field, including the need to explore further the underlying neural mechanisms of AT synesthesia and potential therapeutic interventions.

Cotton (Gossypium spp.) is a major source of natural fiber and an important cash crop. The cotton growth habit and architecture determine its productivity and influence management strategies for commercial production. The GATA transcription factors (TFs) control various developmental processes in plants, such as flower, bract and embryo development, and petal differentiation. As stable transformation is still a bottleneck in many plant species, TRV-VIGS was used to manipulate gene expression in different plants, including Gossypium hirsutum L. In this study, we undertook the TRV-based VIGS to functionally characterize two candidate genes, Gohir.D05G103700 and Gohir.D12G153600, identified through the expression QTL analysis for five floral induction and meristem identity genes using the upland cotton mini-core collection. Virus-induced silencing of the Gohir.D05G103700 gene resulted in up to a 1.4-fold reduction in the transcript level in two inoculated plants, G3 and G4, and Gohir.D12G153600 gene resulted in up to a 2.3-fold reduction in transcript level in a single inoculated plant P05 relative to the mock-treated plant. The TRV2-Gohir.D05G103700 inoculated plants precisely G3 and G4 also exhibited loss of the supernumerary (fourth) floral bract in the squares, whereas the TRV2-Gohir.D12G153600 inoculated plants did not show any observable phenotypic change relative to the mock-treated plants.  Altogether, this study suggested that TRV-VIGS can be used to characterize genes in cotton relatively rapidly and the cotton Gohir.D05G103700 gene is a positive regulator of the indeterminate growth habit in cotton, which could be manipulated to obtain a cotton plant with architecture best suited for the cultivation area.

ADHD, a neurodevelopmental condition, is distinguished by a triad of symptoms including inattention, hyperactivity, and impulsivity. It is frequently accompanied by comorbidities such as anxiety, depression, and learning disabilities. As a result, clinicians often face challenges in accurately diagnosing ADHD and differentiating it from other conditions. As a prospective remedy for ADHD, scientists have investigated Transcranial Direct Current Stimulation (tDCS), a non-invasive technique of stimulating the brain. It involves applying low-intensity electrical currents to specific regions of the brain to modulate neural activity. This review paper aims to provide an overview of the comorbidities associated with ADHD and the differential diagnosis of the condition. It also explores the potential of tDCS as a treatment option for ADHD, including its mechanisms of action and efficacy in improving ADHD symptoms. The comorbidities discussed in this review include anxiety disorders, mood disorders, and substance use disorders. These comorbidities are frequently seen in individuals with ADHD and can complicate the diagnosis and treatment of the condition. The paper also highlights the importance of considering comorbidities when assessing ADHD, as well as the potential impact of these conditions on treatment outcomes. The differential diagnosis section of the paper explores conditions that can present with symptoms similar to ADHD, such as anxiety disorders, mood disorders, and learning disabilities. It emphasizes the need for a thorough assessment and differential diagnosis to identify ADHD and differentiate it from other conditions accurately. The final section of the paper discusses the potential of tDCS as a treatment option for ADHD. It examines the mechanisms of action of tDCS and its efficacy in improving ADHD symptoms, including attention, hyperactivity, and impulsivity. It also explores the potential for tDCS to improve comorbid conditions associated with ADHD. Overall, this review provides a comprehensive overview of comorbidities and differential diagnoses in ADHD and the potential of tDCS as a treatment option. The paper highlights the importance of a thorough assessment and personalized treatment plan for individuals with ADHD, particularly those with comorbidities.

Synthesis of a novel series of chromen-3-yl-pyridine moieties. IR, NMR, and MS spectroscopy were used to confirm the structure of these novel compounds and study of antitumor activity of these compounds. The structure activity relationship investigation demonstrated that 2,4-diamino-5-(3-methoxyphenyl)-7-(2-oxo-2H-chromen-3-yl)-1,8-naphthyridine-3-carbonitrile (16), was more effective and naphthyridine-3-carbonitrile derivatives 17, 18 and pyrido[2,3-d]pyrimidine derivative 12, while compounds 5a,b, 9c, 11, 13 and 14 were moderate activity for antitumor activities.

The COVID-19 pandemic is a devastating blow to the entire world community and changes the order of human life. All efforts and strategies are being carried out to contain and reduce the spread of the SARS-COV-2 virus, both by tightening the health protocol and using vaccines to the public. Currently, several vaccines are available and have passed phase 3 clinical trials, such as vector vaccines (Gamaleya Sputnik V Russia, University of Oxford/AstraZeneca, CanSino, and Janssen Pharmaceutical Companies), mRNA-based vaccines (Moderna/BioNTech/Fosun Pharma/Pfizer), inactivated vaccines (SinoVac and SinoPharm from China, Covaxin from Bharat Biotech India), and adjuvanted recombinant protein nanoparticles (Novavax from the USA) are expected to be able to suppress the spread of the virus and produce a minimum of 70 percent herd-immunity in a population. Each vaccine's efficacy varies from the lowest, namely the Sinovac vaccine (CoronaVac) 50% to the highest the Novavax vaccine (NVX-Cov2373) 96% effectivity value. Moreover, further rigorous research is still being carried out for the development of an effective and efficient vaccine.

This study aims to explore the phenomenon of hadith distortion in hadith literature and analyze its impact on contemporary hadith studies. The intended hadith distortion here refers to the alteration or falsification of hadith narratives that can threaten the integrity and authenticity of sacred texts as sources of Islamic teaching. This article identifies the factors contributing to hadith distortion and its serious consequences in contemporary hadith studies.

Background: Cyber Security is to protect online data and software from cyber threats. These cyberattacks are typically intended to gain access to, change, or delete sensitive information; extort money from users; or disrupt regular corporate activities. It is difficult to keep up a regular follow up with new technologies so it is necessary to keep the important data safe from cyber threats. There are many types of cyber threats; malware, ransom-ware, social engineering, phishing etc. To prevent cyber-attacks one can use password manager tools like LastPass and others. People also use two factor authentication for double security on their accounts. Methods: Boards such as the National Institute of Standards and Technology (NIST) are developing frameworks to assist firms in understanding their security risks, improving cybersecurity procedures, and preventing cyber assaults. The fight against cybercrimes and attack, rganisations needed a strong base there are 5 types of cyber securities; Critical Infrastructure Security, application security, network security, cloud security and (IoT) Security. In the modern time US is highly based on computers and on different software so it is really important for US to be more conscious about the security as they get many threats almost everyday for hacking their data and accounts.Results and Conclusion: Nowadays, even small businesses rarely recover their loss from the cyber-attacks and many back-off from continuing their businesses after being target of hackers. The first cybercrime attack was recorded on 1988 by a graduate student. Now that large companies and even small businesses are aware of cyber-attacks so they try their best to take every precaution to prevent the hacking with double security and password manager tools.

ackground: The swift assimilation of Artificial Intelligence (AI) across multiple industries is altering the worldwide economic terrain. Unprecedented opportunities and difficulties are brought about by this revolutionary technology, which has an impact on innovation, trade, labor markets, and security. Objective: The goal of this study is to thoroughly investigate the economic effects of AI by exploring how it may affect labor markets, innovation, trade internationally, and security. The goal is to offer insights that support strategic decision-making and policy formation by examining current trends, opportunities, and difficulties. Results: The research highlights the dual character of artificial intelligence's influence, highlighting both its potential to spur economic expansion and its drawbacks, including the loss of jobs, a lack of standards, and security issues. The study highlights how crucial cooperation is to overcoming these obstacles and realizing AI's full potential. Conclusion: The balancing opportunities and risks becomes critical as AI continues to change the economic landscape. The report promotes proactive steps including ethical AI design guidelines, ongoing worker retraining, and flexible regulatory strategies. As we shape an AI future that puts inclusion, creativity, and responsible governance first, collaboration emerges as a key theme.

Lamb wave-based structural health monitoring is widely acknowledged as a reliable 11 method for damage identification, classification, localization and quantification. However, due to 12 the complexity of Lamb wave signals, especially after interacting with structural components and 13 defects, interpreting these waves and extracting useful information about the structure's health is 14 still a major challenge. However, deep learning-based strategy offers a great opportunity to address 15 such challenges as the algorithm can operate directly on raw discrete time-domain signals. Unlike 16 traditional methods, which often require careful feature engineering and preprocessing, deep learn-17 ing can automatically extract relevant features from the raw data. This paper proposes an autoen-18 coder based on a bidirectional long short-term memory network with maximal overlap discrete 19 wavelet transform layer to detect the signal anomaly and determine the location of the damage in 20 the composite structure. This approach has the potential to greatly enhance our ability to detect and 21 locate structural damage in composite structures, thereby increasing safety and efficiency.

Peer-to-peer (P2P) content distribution or file sharing system aims to facilitate the dissemination of large files over unreliable networks. Network coding is a new transmission technique that has captured the interest of researchers because of its ability to increase throughput and robustness of the network, and decrease the download time. In this survey paper, we extensively summarize, assess, compare, and classify the most recently used techniques to improve P2P content distribution systems performance using network coding. To the best of our knowledge, this survey is the first comprehensive survey that specifically focuses on the performance of network coding based P2P file sharing systems.

This research critically examines the dichotomies in urban public space and discussions on city evolution over the past two centuries. The original discourse identified amplifies the importance that inclusivity needs to address issues deeper than physical accessibility. The growing diversity and changes seen in urban public open spaces are followed throughout history along a timeline of important socio-political and planning injectors in the Western world. These public spaces are the important spine connecting all the private and semi-private parts of the city. Urban public spaces have seen population changes due to globalisation, resulting in mobility and changes due to the different needs of its diverse user base. In this paper, a rigorous quasi-chronological investigation is presented. Firstly, the context of the evolution of space is established. Secondly, a closer focus on inclusion research provides a thorough analysis of the utopian city plans, the development of Haussmann's Paris and the later plans of the Centrist and the Decentrist. Thirdly, a critical and analytical understanding of the effect these precursors have had on the city's public spaces, and the hierarchies it established in a nuanced manner are made explicit. The culmination of this research process is the identification of outcomes associated with inclusivity. Findings are established across three significant themes—a) Understanding public space as social space, b) Components of inclusivity, and c) Values of inclusivity including accessibility, sense of place, conviviality and resilience. Key insights and guidance for inclusivity as a key constituent of social sustainability are the unique contribution.

The behavior of convective boundary conditions is studied to delineate their role in heat and mass relegation in the presence of radiation, chemical reaction, and hydromagnetic forces in three-dimensional Powell-Eyring nanofluids. Implications concerning non-Fourier’s heat flux and non-Fick’s mass flux with respect to temperature nanoparticle concentration were examined to discuss the graphical attributes of the principal parameters. An efficient optimal homotopy analysis method is used to solve the transformed partial differential equations. Tables and graphs are physically interpreted for significant parameters

The research introduces the concept of Strong Energy (SE) as a force that encompasses all the different forms of energy in the universe. The study aims to create a mathematical framework that can describe the relationship between these different types of energy and how they can be converted from one form to another. The paper explores the theoretical implications of this model and investigates how it aligns with established physics principles like the conservation of energy and fundamental forces. The paper also discusses potential experiments and the impact this research could have on cosmology, particle physics, and our understanding of energy. This work sets the stage for future research in this area of study.

Keeping in mind the increasing trend and need for serious games in science education, we have done a systematic literature review. These papers show the trends and patterns of research carried out in this field from the year 2011 to 2020. Specifically, we investigated country-wise concentration and the most common evaluation methods. Literature is reviewed from IEEEexplore, Springer, and Scopus. Moreover, we discussed the role of Augmented Reality(AR) games in teaching physics. Lastly, we have discussed the positive and negative aspects of serious games in science education in particular, and the trend of using serious games in the past decade in education in general.

LIFI was first introduce by Professor Harald Haas on July 2011. Light fidelity (LI-FI) may be a technology which uses light as a medium to travel from one place to a different. It uses Light like Light Emitting Diode (LED) visible radiation Communication (VLC) for data Transferring and Internet connection. LIFI may be a technique which uses light as a medium because it uses light to travel it's 20 times faster than any WIFI within the world. during this paper we speak about things like what's LIFI and the way it's better then WIFI why we want LIFI and What changes did bring LIFI in our Future LIFI. How it'll make IOT devices far better than before The Technique to implement LIFI and also the problem we face of implementation of LIFI

Bacterial infections are world-wide problem and resistant bacteria is increasing globally that lead to treatments failure. Thus, it is important to find new techniques that are effective for the treatment antibiotic-resistant microorganisms. Green medicine used for the medication of different bacterial infection. Therefore , the study aimed to evaluate the immunomodulatory activity of essential fatty acid semi carbazide (EFASC) compounds extracted from flaxseed to eradicate resistance pathogens . Crud extracts of Linum usitatissimum was extracted by hexane for extraction of EFASC. The results of LD₅₀ appear that a live suspension of E.coli was 0.49×10⁷ ,while HK E.coli was 10⁸ , 125 mg /ml were the optimum dose in stimulate immune response of EFASC which gave maximum dose of total WBC , Neutrophil and Monocyte count. The immunomodulatory activity appear that E.coli + EFASC released moderate levels of IL-4 . HK E.coli release higher IL-4 lead to increase the hypersensitivity and hyper responses of immune system. HK + EFASC immunogen revealed moderate increased in IL-12 mean level 0.99 pg /ml, HK bacteria recorded 1.49 pg/ml, while the mean of EFASC revealed no significant different compare with control. An effective protection was observed in immunized groups with HK E.coli and EFASC challenged with 100 of LD50 of a live E.coli.

Artificial Intelligence (AI) in healthcare has ushered in a revolutionary era by transforming the way we provide care and reduce adverse consequences. This paper explores the field of AI applications in healthcare, including side effect management, streamlined administrative procedures, and customized treatment programs.

Background: Artificial intelligence can help improve the quality of healthcare by analyzing vast amounts of data and providing more effective and personalized treatment plans. Researchers are working on developing AI-powered solutions that can help improve the outcomes of patients. Objective: To explore the potential of AI in improving healthcare outcomes and patient experience. Results: The study suggests that AI can improve healthcare efficiency and patient outcomes but cannot fully replace human healthcare professionals. AI can assist healthcare professionals in their work, leading to better resource utilization and improved patient care. However, there is still a need for human healthcare professionals to oversee AI systems and provide empathy and personalized care to patients. Conclusion: While there is immense potential for AI in healthcare, it is not yet feasible to replace human healthcare workers. Instead, it should be viewed as a tool that can help improve the efficiency and effectiveness of human healthcare.

Abstract Incretin mimetics, also known as glucagon-like peptide-1 (GLP-1) receptor agonists, are a class of medications used to treat type 2 diabetes by mimicking the actions of incretin hormones in the body. These hormones are responsible for promoting insulin release from the pancreas in response to nutrient intake, as well as decreasing glucagon secretion, slowing gastric emptying, and promoting satiety. By imitating these actions, incretin mimetics help to regulate blood sugar levels in individuals with diabetes and glucose intolerance. One of the key benefits of incretin mimetics is its ability to lower blood sugar levels without causing hypoglycemia. This is especially important for individuals with diabetes who may experience dangerous drops in blood sugar levels when using other medications. Additionally, incretin mimetics have been shown to promote weight loss in some individuals, making them a valuable option for those struggling with obesity in addition to diabetes. Incretin mimetics are administered by injection, once or twice daily, depending on the specific medication. They are often combined with other diabetes medications, such as metformin or insulin, for optimal blood sugar control. These medications are generally well-tolerated, with common side effects including nausea, vomiting, and diarrhea, which usually diminish over time as the body adjusts to the medication. Studies have shown that incretin mimetics can help improve cardiovascular outcomes in individuals with diabetes, including reducing the risk of heart attacks and strokes. This is particularly significant given the increased risk of cardiovascular disease in individuals with diabetes. Incretin mimetics also have been shown to preserve pancreatic beta-cell function, which is responsible for producing insulin. This can help slow the progression of diabetes and reduce the need for higher insulin doses over time. Despite their many benefits, incretin mimetics are not without limitations. They can be expensive compared to other diabetes medications, which may make them less accessible for some individuals. Additionally, there have been concerns about the potential risk of pancreatitis and pancreatic cancer associated with the use of these medications. However, more research is needed to fully understand these risks. It is important for healthcare providers to carefully assess each individual's unique needs and medical history when considering the use of incretin mimetics. They may not be appropriate for everyone, particularly those with a history of pancreatitis or pancreatic cancer. Patients should also be educated about these medications' proper administration and potential side effects to ensure their safety and efficacy. Overall, incretin mimetics have emerged as an important therapeutic option for individuals with type 2 diabetes, offering a unique mechanism of action that can help improve blood sugar control, promote weight loss, and reduce cardiovascular risk. With ongoing research and development in this field, incretin mimetics continue to show promise as valuable tools in managing diabetes and its associated complications and comorbidities.

Proteins possess complex three-dimensional structures, and these structures are stable only within specific ranges of temperature which mostly correspond to the temperature ranges of the host organisms. However, few exceptional proteins, called heat-stable proteins, are stable at temperatures that are substantially higher than those tolerated by the host organisms themselves. Most of the heat-stable proteins possess heat stability to perform their functions at high temperatures, but some of them are intrinsically heat-stable due to their structure. Heat-stable proteins are usually divided into three or four groups depending upon the intricacies of their structures and thermal behaviors. Their peculiar property, i.e. heat-stability, makes them very valuable in applications such as polymerase chain reaction, industrial processes requiring high temperature, and protein engineering. Heat-stability also makes it feasible to purify such proteins, from the rest of the heat-labile proteins, using a simple heat-treatment method. Moreover, heat treatment can be used as a combined cell-lysis and protein purification step which, as compared to conventional methods, can result in a higher yield of heat-stable proteins. Furthermore, some special heat-stable proteins, i.e. intrinsically disordered proteins (which include the proteins involved in important neurodegenerative diseases), need heat-treatment step, in some cases, as the only way for their successful purification and study. Hence, this paper provides a first-ever comprehensive review of all major aspects of heat-stable proteins, i.e., their structure, evolution, classification, significance, and heat-treatment mediated purification.

The purpose of this paper is to describe a feature selection algorithm and its application to enhance the accuracy of the reconstruction of phylogenetic trees by improving the efficiency of tree construction. Applying machine learning models for Arabic and Aramaic scripts such as Deep Neural Networks (DNN), Support Vector Machines (SVM) and Random Forests (RF) each model was used to compare the phylogenies. The methodology was utilized with a dataset containing Arabic and Aramaic scripts, demonstrating its relevance in a range of phylogenetic analyses. Results emphasize the essential role of feature selection by DNNs is outperforming other models in terms of Area Under the Curve (AUC) and Equal Error Rate (EER) across various datasets and fold sizes. Additionally, SVM and RF models show important understandings, advantages and limits of each approach within the context of phylogenetic analysis. This method not only simplifies the tree structures but also enhances their Consistency Index. Therefore offering a robust framework for evolutionary studies. The findings highlight the applications of machine learning in phylogenetics suggesting a path toward accurate and efficient evolutionary analyses and adding a deeper understanding of evolutionary relationships.

Carrageenan (car-), used in the pharmaceutical as well as food industry, is marine sulfated polysaccharides. The carrageenan blends (CB) of kappa (κ-), iota (ι-), and lambda (λ-) of 50/50 weight by weight are multipurpose and biocompatible hydrophilic polymers. They were subjected to adsorption of copper (Cu2+) ions. The aim of the study was to conduct extensive rheological and mechanical studies rendering them suitable for biological purposes. The rheology was conducted at various temperatures using a frequency curve, frequency sweep, loss modulus, and storage modulus analysis. Models of rheology like Ostwald, Bingham, and Modified Bingham models were utilized. The rheological results demonstrated non-Newtonian/pseudo-plastic behavior at various temperatures. The models of rheology demonstrated good flow properties and rheological performance of these materials. These materials could be exploited for their application in pharmaceuticals, food, and cosmetics. Thus, our study reflects that these CB can be safely exploited in the healthcare, pharmaceutical, and food industry. However, further studies should be conducted to evaluate their effectiveness in clinical studies.

Generic object detection is one of the most important and flourishing branches of computer vision and has real-life applications in our day to day life. With the exponential development of deep learning-based techniques for object detection, the performance has enhanced considerably over the last 2 decades. However, due to the data-hungry nature of deep models, they don't perform well on tasks which have very limited labeled dataset available. To handle this problem, we proposed a transfer learning-based deep learning approach for detecting multiple pigs in the indoor farm setting. The approach is based on YOLO-v2 and the initial parameters are used as the optimal starting values for train-ing the network. Compared to the original YOLO-v2, we transformed the detector to detect only one class of objects i.e. pigs and the back-ground. For training the network, the farm-specific data is annotated with the bounding boxes enclosing pigs in the top view. Experiments are performed on a different configuration of the pen in the farm and convincing results have been achieved while using a few hundred annotated frames for fine-tuning the network.

Animal behavior analysis is a crucial tasks for the industrial farming. In an indoor farm setting, extracting Key joints of animal is essential for tracking the animal for longer period of time. In this paper, we proposed a deep network that exploit transfer learning to trained the network for the pig skeleton extraction in an end to end fashion. The backbone of the architecture is based on hourglass stacked dense-net. In order to train the network, key frames are selected from the test data using K-mean sampler. In total, 9 Keypoints are annotated that gives a brief detailed behavior analysis in the farm setting. Extensive experiments are conducted and the quantitative results show that the network has the potential of increasing the tracking performance by a substantial margin.

Infertility affects approximately 15% of couples worldwide, an estimated 30% of which is related to male factor infertility. Application of low level laser therapy (LLLT) to improve fertility status is a rapidly growing discipline in medicine. Laser therapy triggers a variety of biological processes through interaction with primary cellular photoacceptors. The present review aims at evaluating the literature available in the MEDLINE/ PubMed on cellular and molecular mechanisms of photobiomodulation in the domains of reproductive and veterinary medicine. We primarily focused on the clinical application of laser treatment on seminal quality, in particular its role in promoting spermatozoa motility, as well as the role of phototherapy in modulating assisted reproduction (ART). Additionally, we investigated the strength of evidence in support of the positive impact of photobiomodulation on facilitating ART.

To reduce solar power production invariance, it is critical to study varying patterns of power production in the concerned region. Analyzing the patterns of past power production trends can help simulate power production scenarios for future. The current study area is around Amsterdam, located in Netherlands. PVoutput.org website is used to mine 6 months of solar power production data for 120 stations around Amsterdam city. FME Workbench software is used to actively fetch the data from the mentioned website and manage in a MySQL database. Solar attenuation maps created using ArcGIS, helped to graphically visualize the variations in solar power production at different times and locations. Further, spatial autocorrelation is checked between the stations using semi-variograms in geostatistical tool of ArcMap. This feature allows to check whether the stations located close to each other are more correlated to each other rather than stations which are far apart. The statistical data analysis of power production can aid solar power production companies to better interpolate and predict solar power in advance for the concerned study region.

Cardiac amyloidosis is caused by amyloid fibrils that deposit in the myocardial interstitium, causing restrictive cardiomyopathy and eventually death. The electromechanical, inflammatory, and autonomic changes due to amyloid deposition result in arrhythmias. Atrial fibrillation is by far the most common arrhythmia. Rate control strategy is generally poorly tolerated due to restrictive filling physiology and heart rate dependance, favoring adoption of rhythm control strategy. Anticoagulation for stroke prophylaxis is warranted irrespective of CHA2DS2Vasc score in patients with favorable bleeding profile; data on left appendage closure devices is still insufficient. Ventricular arrhythmias are also not uncommon and the role of implantable cardioverter-defibrillator in cardiac amyloidosis is controversial. There is no evidence of improvement in outcomes when used for primary prevention in these patients. Bradyarrhythmia is most commonly associated with sudden cardiac death in cardiac amyloidosis. Pacemaker implantation can help provide symptomatic relief but does not confer mortality benefit.

This survey was conducted on 4 tribes (Ababda, Bisharia, Nubian and Rashayda) live in the south of the Nile and the Eastern Desert of Egypt with the aim to document and compare the traditional herbal medicines and assess the relationships among these tribes. A total of 180 interviews were conducted with the Bedouins and herb healers. Thirty-nine species belonged to 36 genera and 27 families were employed. Fabaceae and Poaceae and Rutaceae were the species-rich families. The used wild species comprised 43.6%, cultivated species (38.5%) and the imported from herbalist shops (17.9%). The leaves were the most used parts (31%), followed by stems and fruits with about 22% each. Distinct species included Acacia nilotica is used in the treatment of dental pain with use value 33.3%, Cymbopogon schoenanthus subsp. proximus in treatment of both cough or headache with use values 35 and 30.6% and a combination of Acacia nilotica with Lawsonia inermis in the treatment of sore throat with use value 22.2%. The highest similarity was recorded between Nubian and Rashayda tribes (55.3%), Ababda and Bisharia (46.8%). Diarrhea and headache were the most popular diseases with 7 different treatments, cough and dental pains with 6 treatments.

Recent progress in microfabrication technique allowed the rapid development of neural implants. They are getting categorized as effective tools for clinical practice, especially to treat traumatic and neurodegenerative disorders. Microelectrode arrays already have been used in numerous neural interface devices. Basically, almost all neural implants have been developed based on BCI (Brain Computer Interface) system. When BCI system falls under invasive technique, it is referred as BMI or Brain Machine Interface. BMIs hold promises for neurorehabilitation of motor and sensory function, cognitive state evaluation and treatment of neurological chaos. A directed overview of the field of neural implants is discussed in this article. The aim of this review is to give a brief introduction of neural prosthetics as well as their exciting applications in treating neurological disorders and a deep discussion on their functionality are mentioned. BCI system and their different types, their functionality, their pros and cons, how other neural implants developed, and their present status have been covered. Different possibilities and possible future of deep brain stimulation (DBS), Neuralink, motor and sensory neural prosthetics are further discussed.

In this study, we present different methods of estimating fuzzy reliability of a two-parameter Rayleigh distribution via the maximum likelihood estimator, median first-order statistics estimator, quartile estimator, L-moment estimator, and mixed Thompson-type estimator. The mean-square error MSE as a measurement for comparing the considered methods using simulation through different values for the parameters and unalike sample sizes is used. The results of simulation show that the fuzziness values are better than the real values for all sample sizes, as well as the fuzzy reliability at the estimation of the Maximum

This research aims to identify the role of the Dyson model for strategic development in achieving strategic success, and the starting point of the research was the following main question: What is the role of the Dyson model in achieving success?The research was applied in the field in the departments of the Baghdad Municipality, where the examination list was relied upon, which included a set of questions that the senior and middle leaders in the Baghdad Municipality answered, and it was the main means by which the information related to the field of research was collected, and the checklist included two variables and three dimensions From each variable, as each dimension included four questions that express indicators that revolve around one of the research hypotheses, and the case study methodology was used, which defined its path and steps, collected and analyzed field data, and linked it to its theoretical framework, in order to reach To achieve the goal of completing this research, and through analyzing, interpreting and discussing the results, the most important results were drawn up: It was found that the principle of motivation within the departments of Baghdad Municipality does not exist and this affects the employees who do not receive it from the higher leaders in their departments, and this shows that the leaderships in The Municipality of Baghdad do not have the skills and experience. Baghdad Municipality seeks to work alone and not to involve employees who have experiences and skills and strive to achieve development in their departments, and this is what the community members expressed. Among them and poor business completion in their departments.

In this work, PMMA(Poly methyl methacrylate) microfluidic system was used as a micro-reactor for urea hydrolysis by urease enzyme with use conductivity principle and utilize sound level meter(SLM) App in smartphone as a novel detector by considering the peak height in the App as an indicate for urea concentration. the advantage of use small volume and how the reaction carried on in the microfluidic system with simple and low cost are discussed, and the results were analyzed and statically determine. The linearity, detection limit (3×noise )and Correlation Coefficient, 62.5-500 ppm, 31.25 ppm and 0.992 respectively also, recovery studied were between(98.5-100.13%).

4-component relativistic atomic and molecular calculations are typically performed within the no-pair approximation where negative-energy solutions are discarded, hence the symmetry between electronic and positronic solutions is not considered. These states are however needed in QED calculations, where furthermore charge conjugation symmetry becomes an issue. In this work we shall discuss the realization of charge conjugation symmetry of the Dirac equation in a central field within the finite basis approximation. Three schemes for basis set construction are considered: restricted, inverse and dual kinetic balance. We find that charge conjugation symmetry can be realized within the restricted and inverse kinetic balance prescriptions, but only with a special form of basis functions that does not obey the right boundary conditions of the radial wavefunctions. The dual kinetic balance prescription is on the other hand compatible with charge conjugation symmetry without restricting the form of the radial basis functions. However, since charge conjugation relates solutions of opposite value of the quantum number κ, this requires the use of basis sets chosen according to total angular momentum j rather than orbital angular momentum ` . As a special case, we consider the free-particle Dirac equation, where the solutions of opposite sign of energy are related by charge conjugation symmetry. We note that there is additional symmetry in those solutions of the same value of κ come in pairs of opposite energy.

In this paper, it is proved that s-iteration with error and Picard-Mann iteration with error iterative processes converge strongly to the unique fixed point of Lipschitzian strongly pseudo-contractive map. This convergence is almost -stable and -stable. Applications of these results to the operator equations, where is a strongly accretive and accretive mappings of into itself.

Asthma causes chronic coughing, wheezing, dyspnea, and chest pressure. This study assessed asthmatic patients' knowledge, attitudes and awareness of bronchial asthma and proper education on its meaning, risk factors, symptoms, diagnosis, management, and prevention practice. We performed a cross-sectional interventional asthma KAP survey in Erbil, Iraq. We adapted a validated study questionnaire from KAP studies in other nations to the Erbil situation and culture. In Erbil, Kurdistan, Iraq, two major hospitals' asthma clinics were studied. We chose 250 asthmatic ICU patients from October 2018 to July 2019. Health education was comprehensive. The health education program used a Kurdish PowerPoint with a printout. 25 groups got two-weeks of one-hour health education pre-intervention. Each group was questioned before, 2 and 12 weeks after health education. All data were analyzed by SPSS v26. The mean age of the respondent was 37.52±15.16 with 48.7 % respondent having a positive family history of asthma. After 2weeks of health education intervention, respondent have a higher knowledge score, positive attitudes compared to pre-education and after 12 weeks of education with a significant difference (P < 0.001) with improvised prevention practice. Health education programs led to considerable improvements in asthmatic patients' knowledge, attitudes, and practices regarding their condition. After receiving health education for a period of two weeks, the majority of the participants answered correctly regarding asthma, its causes, and the elements that trigger asthma attacks.

Epigenetic alterations have contributed greatly to human carcinogenesis. Conventional epigenetic studies have been predominantly focused on DNA methylation, histone modifications and chromatin remodelling. However, recently, RNA modification (m6A-methylation) also termed ‘epitranscriptomics’ has emerged as a new layer of epigenetic regulation due to its diverse role in various biological processes. In this review, we have summarized the therapeutic potential of m6A-modifiers in controlling haematological disorders especially acute myeloid leukemia (AML). It is a type of blood cancer affecting specific subsets of blood-forming hematopoietic stem/progenitor cells (HSPCs) which proliferate rapidly and acquire self-renewable capacities with impaired terminal cell-differentiation and apoptosis leading to abnormal accumulation of white blood cells, and thus an alternative therapeutic approach is required urgently. Here, we have described how RNA m6A-modification machineries EEE (Editor/writer: Mettl3, Mettl14; Eraser/remover: FTO, ALKBH5 and Effector/reader: YTHDF-1/2) could be reformed into potential druggable candidate or as RNA modifying drug (RMD) to treat leukemia. Moreover, we have shed-light on the role of microRNA and suppressor of cytokine signalling (SOCS/CISH) in increasing anti-tumor immunity towards leukemia. We anticipate, our investigation will provide a fundamental knowledge in nurturing the potential of RNA modifiers in discovering novel therapeutics or immunotherapeutic procedures.

The growing emphasis on sustainability and environmental stewardship in the pharmaceutical industry necessitates innovative solutions to manage pharmaceutical waste, particularly medication bottles. This research paper explores the potential of integrating Radio Frequency Identification (RFID) and blockchain technology to enhance the traceability, accountability, and efficiency of recycling empty medication bottles. By utilizing RFID for real-time tracking and blockchain for secure, immutable data storage, this proposed system improves transparency across the supply chain and incentivizes consumer participation in recycling programs. The solution provides benefits to pharmaceutical manufacturers, regulators, and consumers, contributing to sustainability, regulatory compliance, and environmental protection.

This panel study investigates the relationship between green logistics indices, economic, environmental, and social factors in the perspective of Asian emerging economies. This study adopted FMOLS and DOLS methods to test research hypothesis, catering the problem of endogenity and serial correlation. The results suggest that logistics operations, particularly LPI2 (efficiency of customs clearance processes), LPI4 (quality of logistics services) and LPI5 (trade and transport-related infrastructure), are positively and significantly correlated with per capita income, manufacturing value added and trade openness. While, greater logistics operations are negatively associated with social and environmental problems including, climate change, global warming, carbon emissions, and poisoning atmosphere. In addition, human health is badly affected by heavy smog, acid rainfall, and water pollution. The findings further extend and reveal that political instability, natural disaster and terrorism are also a primary cause of poor economic growth and environmental sustainability with poor trade and logistics infrastructure. Further, the application of renewable energy resources and green practices can mitigate negative effects on social and environmental sustainability without compromising the performance of economic growth. There is very limited empirical work presented in literature using renewable energy and green ideology to solve macro-level social and environmental problems, while this study will assist the policymakers and researchers to understand the importance of green concept in improving countries’ social, economic and environmental performance.

We do this research to investigate the relationship between renewable energy, public health expenditure, logistics performance indices, and economic and environmental sustainability in the ASEAN member states, through the analysis of a panel data from 2007 to 2017. The study used secondary data, which is downloaded from the World Bank Website and employs SEM (Structural Equation Modelling) model for testing hypothesis. The results show that the usage of renewable energy in logistical operations would enhance the environmental and economic performance in terms of mitigating carbon emissions and greenhouse gas emissions. While, public health expenditure and environmental performance is negatively correlated, which confirms that greater environmental sustainability with lower carbon emissions and greenhouse gases will improve human health and economic growth. Moreover, greater public health expenditure and poor environmental performance has negative effect on economic growth, inefficiency and low productivity of labor slowdown to the economic activities. For another side, the usage of renewable energy and the adoption of green practices in international logistics will develop the environmental sustainability, establish better image of a country and attract foreign direct investment inflows, and also minimize carbon emissions and public health expenditure, spurring sustainable economic growth with better export opportunities in pro-environmental countries.

In the previous work, the pure fatigue behavior of AM60 magnesium alloy (PF-AM60) was compared with the corrosion fatigue behavior of these specimens (CF-AM60). In this research, in continuation of the previous job, the pure fatigue behaviors of AM60 with polylactic acid (PLA) coating (PF-AM60-PLA) and also, corrosion fatigue behaviors of magnesium alloy with PLA coating (CF-AM60-PLA) were evaluated. Polymer coating was made by fused deposition modeling (FDM) with a 3D printer and attached to standard fatigue test specimens with a glue. Then, they were immersed in the simulated body fluid (SBF) for 27 days. In the end, a high-cycle bending fatigue test was performed on samples. The fracture surface of the samples was also observed using the field emission scanning electron microscopy (FESEM). Due to corrosion, the weight of the specimens redcued by an average of 35%. The corrosion rate decreased in the first 7 days and then increased. PF samples with coating had an average of 49% increase in fatigue lifetime. Regarding the CF samples, despite the use of a 10 times stronger solution, the fatigue lifetime of these samples decreased by only 35%. FESEM results also showed cleavage plates and striations. In addition, the separation of the glue from the coating and Mg was observed. Corrosion products including microcracks and holes were seen on the fracture surface of CF specimens, which caused stress concentration and crack growth. Holes caused by the release of gases were also observed in polymer coatings.

The textile processing sector is accountable for the extensive utilisation and pollution of freshwater resources. Due to heightened consumer awareness of environmental legislation regarding freshwater contamination, the textile sector is compelled to review and improve their current water consumption practices. Foan dyeing technique is a highly promising alternative that has the ability to contribute to a more sustainable future. This review paper discussed the current state of foam dyeing technology, highlighting its advantages in terms of re-duced consumption of water and energy, as well as minimal usage of dyes and chemicals compared to conventional methods. The foam configuration allows for more effective application of dyes. As a result, there is a decrease in dye consumption and a reduction in processing time. The process is environmen-tally sustainable since it significantly reduces water pollution. Furthermore, foam dyeing method consumes less energy due to its lower dying temperature need compared to conventional processing technology. Additionally, this paper highlights the continued investigation of foam dyeing on many types of textile substrates (such as fibres, yarns, and fabric) and compositions including cotton, polyester, and their mixtures. In addition, the techno-economic comparison of foam dyeing and conventional dyeing is also given. This review paper addi-tionally endorses the Sustainable Development Goals (SDG 6, clean water and sanitation) by examining the preservation of usable water and the decrease in wastewater discharge through foam dyeing technology. Lastly, the potential advantages of foam dyeing in terms of significantly reducing water consump-tion and the generation of waste in the textile industry were also addressed.

The classification and summarization of online reviews using machine learning and deep learningbased approaches are the subject of this systematic literature review. Consumers, companies, and researchers can now find vital information from online reviews. Automatically categorizing and summarizing these reviews can offer useful information and facilitate decision-making. The purpose of this study is to offer a thorough overview of the current methodology, approaches, and developments in this area. The review concentrates on machine learning-based methods for categorization and summarizing tasks, highlighting their advantages, drawbacks, and new developments. This systematic review provides insights into the most recent methodologies and indicates prospective directions for further investigation by synthesizing the data from a wide range of pertinent research publications

Plasma being the fourth and most abundant form of matter extensively exists in the universe in the inter-galactic regions. It provides an electrically neutral medium of unbound negative and positive charged particles, which has been produced by subjecting air and various other gaseous mixtures to strengthen the electromagnetic field and by heating compressed air or inert gasses for creating negative and positive charged particles known as ions. Nowadays, many researchers are paying attention to the formation of artificial Plasma and its potential benefits for mankind. The literature is sparsely populated with the applications of Plasma. This paper presents specific methods of generation and applications of Plasma, which benefits humankind in various fields, such as in electrical, mechanical, chemical and medical fields. These applications include hydrogen production from alcohol, copper bonding, semiconductor processing, surface treatment, Plasma polymerization, coating, Plasma display panels, antenna beam forming, nanotechnology, Plasma Torch, Plasma pencils, low-current non-thermal Plasmatron, treatment of prostate cancer, Plasma source ion implantation, cutting by Plasma, Plasma etching, pollution control, neutralization of liquid radioactive waste, etc. Resultantly, worth of Plasma technology in the medical industry is increasing exponentially that is closing the gap between its benefits and cost of equipment used for generating and controlling it.

Background: Video assisted thoracoscopic surgery (VATS) has become the recommended approach for treatment of resectable lung cancer. However, no large randomized clinical trial has been conducted formally comparing surgical resections completed by VATS to those done by open thoracotomy (OT) in low volume centers. The current study sought to assess differences in recurrence-free survival (RFS), overall survival (OS), positive margins and postoperative length of stay (LOS) between VATS and OT lobectomies in our center. Method: A single institution retrospective chart review from May 2005 through May 2015 was conducted. All patients diagnosed with stage I through III lung cancer who underwent surgical resection were selected. Patient and tumor characteristics recorded included age at diagnosis, sex, tobacco use, tumor location (side and lobe), stage, size and receipt of chemotherapy or radiotherapy. Chis-square and Wilcoxon-Mann-Whitney tests were used to compare demographics, tumor characteristics and LOS. Multiple logistic and Cox regression analyses were used to compute relative risk (RR) for positive margins and mortality hazard ratios along with 95 percent confidence intervals (95%CI), respectively. Results: Of the 235 patients, 101 subjects had VATS while OT was performed in 134 patients. Age at diagnosis, sex, tobacco use, tumor location, and size were comparable for VATS and OT. No significant difference was observed in the relative risk of positive margins for VATS versus OT, RR = 0.56 (95%CI = 0.26, 1.05). However, VATS had shorter median LOS compared to OT (4 vs. 6 days, respectively), p = 0.002. A comparison of VATS versus OT showed no significant difference in the risk of recurrence, HR = 1.21 (95%CI = 0.74, 2.00), or death, HR = 1.34 (95%CI = 0.88, 2.06), in the intent-to-treat population. Similarly, no significant differences in recurrence or mortality risk were observed between VATS versus OT for analyses conducted separately for each cancer stage group or those limited to patients with negative margins. Conclusion: Our study indicates that compared to OT, VATS leads to shorter LOS while achieving comparable margins status, recurrence-free and overall survival regardless of tumor stage at diagnosis.

Mitochondrial Ca2+ ([Ca2+]M) uptake through Ca2+ uniporter (MCU) is central to many cell functions such as bioenergetics, spatiotemporal organization of Ca2+ signals, and apoptosis. MCU activity is regulated by several intrinsic proteins including MICU1, MICU2, and EMRE. While significant details about the role of MICU1, MICU2, and EMRE in MCU function have emerged recently, a key challenge for the future experiments is to investigate how these regulatory proteins modulate mitochondrial Ca2+ influx through MCU in intact cells under pathophysiological conditions. This is further complicated by the fact that several variables affecting MCU function change dynamically as cell functions. To overcome this void, we develop a data-driven model that closely replicates the behavior of MCU under a wide range of cytosolic Ca2+ ([Ca2+]C), [Ca2+]M, and mitochondrial membrane potential values in WT, MICU1 knockout (KO), and MICU2 KO cells at the single mitochondrion and whole-cell levels. The model is extended to investigate how MICU1 or MICU2 KO affect mitochondrial function. Moreover, we show how Ca2+ buffering proteins, the separation between mitochondrion and Ca2+-releasing stores, and the duration of Ca2+-releasing channels affect mitochondrial function under different conditions. Finally, we demonstrate an easy extension of the model to single channel function of MCU.

In this paper, we discuss voltage control method for buck converter operating in continuous conduction mode (CCM) using analog feedback system. The aim of this work is to control the output voltage of a buck converter during the variation in load current. This is obtained using analog feedback made with operational amplifier (Opamp). However, the same technique can be applied to other DC-DC converters (e.g boost, buck-boost, cuk converter, etc) in CCM mode, but for the purpose of analysis buck converter is chosen as an example.

The Epithelial- Mesenchymal Transition (EMT) is a biological phenomenon associated with explicit phenotypic and molecular changes in cellular traits. Unlike the earlier-held popular belief of it being a binary process, EMT is now thought of as a landscape including diverse hybrid E/M phenotypes manifested by varying degrees of the transition. These hybrid cells can co-express both epithelial and mesenchymal markers and/or functional traits, and can possess the property of collective cell migration, enhanced tumor-initiating ability, and immune/targeted therapy-evasive features, all of which are often associated with worse patient outcomes. These characteristics of the hybrid E/M cells have led to a surge in studies that map their biophysical and biochemical hallmarks that can be helpful in exploiting their therapeutic vulnerabilities. This review discusses recent advances made in investigating hybrid E/M phenotype(s) from diverse biophysical and biochemical aspects by integrating live cell-imaging, cellular morphology quantification and mathematical modeling, and highlights a set of questions that remain unanswered about the dynamics of hybrid E/M states.

This paper utilizes a life cycle assessment to evaluate the energy resources and environmental impacts of three heating systems. In the first step, life cycle assessments (LCAs) are prepared for the renewable, conventional, and combined systems. The system boundary of the LCA method is "cradle to gate," which means it includes the entire life cycle of a product or process. This includes energy supply, transport, energy generation, and operational energy use. The system scenarios were compared based on ecological and energy loads in the second step. Primary energy, resources, emissions, and environmental potentials are calculated for the system scenarios using the life cycle assessment methods CML 2016 and ReCiPe 2016. Finally, models for environmental reliability and complex decision-support tools have been developed. This work addresses two main questions: how to characterize the environmental and energy impacts of the systems under study, and what is the optimal scenario for the system? The research results show that the gas boiler system has a greater environmental impact. The most significant differences between the systems relate to the degrada-tion of abiotic fossil fuels when using a gas boiler and the process of acidification when using an electric heat pump. The results can be used to develop sustainable heating systems with reduced environmental impacts and enhanced energy efficiency.

Bioprinting is a relatively new yet evolving technique predominantly used in regenerative medicine and tissue engineering. 3D bioprinting techniques combine the advantages of creating Extracellular Matrix (ECM) like environments for cells and computer-aided tailoring of predetermined tissue shapes and structures. The essential application of bioprinting is for the regeneration or restoration of damaged and injured tissues by producing implantable tissues and organs. The capability of bioprinting is yet to be fully scrutinized in sectors like the patient-specific spatial distribution of cells, bio-robotics, etc. In this review, currently developed experimental systems and strategies for the bioprinting of different types of tissues as well as for drug delivery and cancer research are explored for potential applications. This review also digs into the most recent opportunities and future possibilities for the efficient implementation of bioprinting to restructure medical and technological practices.

In this article, the effect of substitution of Zr and Ga in Dy2Fe17 prepared by arc melting technique are studied. The substitution of Zr and Ga in Dy2Fe17 was found to have an important effect on their structure and magnetic properties. The Rietveld analysis conformed that the crystalline system wereTh2Ni17 structure. Lattice parameters a (Å) and c (Å), unit cell volume (Å3), bonding distance (Å) were calculated by using Rietveld analysis. The unit cell volume of Dy2Fe17-xZrx and Dy2Fe16Ga1-xZrx increase linearly with the Zr and Ga substitution. The substitution of Zr and Ga are limited up to x=1 in order to avoid the decrease in saturation magnetization. The Curie temperature (Tc) of Dy2Fe17-xZrx and Dy2Fe16Ga1-xZrx are found to be Zr content dependent. The Curie temperature is found to be increasing first and then decrease for higher Zr content. The maximum curie temperature was observed 510K at x = 0.75 for Dy2Fe17-xZrx and 505.1 K at x = 0.5 for Dy2Fe17-xZrx which are102 K and 97 K higher than Dy2Fe17. The room temperature Mössbauer analysis shows the decrease in average hyperfine field and increase in isomer shift with Zr doping.

Background: This research examines how market knowledge and artificial intelligence (AI) interact in different market designs such as business-to-business (B2B) settings while taking emerging technologies and the changing digitalization landscape into account. Objective: The main goal is to understand how AI affects market knowledge in different market designs such as business-to-business (B2B) contexts, taking into account language barriers, practical difficulties, and the revolutionary effects on decision-making and customer interactions. Result: They underscore the transformative potential of artificial intelligence (AI) by highlighting how it shapes market knowledge, encourages customized approaches, and improves marketing efficacy in the business-to-business (B2B) space. Conclusion: In order to create a path for responsible AI integration in B2B marketing, the study concludes with recommendations for standardized terminology related to AI, practical insights into implementation challenges, and ethical issues.

Intracortical microelectrodes that can be implanted have the ability to capture fast-changing neuron action potentials in the living brain. Despite this potential, many obstacles must still be overcome for reliable, long-term, high-quality recordings and accurate analysis of brain activity. These challenges include improving recording quality, enhancing recording stability, increasing recording capacity, and adding multi-functional features. One potential approach to enhance implantable microelectrodes involves the advancement of materials, refinement of implantation methodologies, and augmentation of the number of sites for recording. However, these challenges are still being actively researched, and advancements in microelectrode technology are underway. The difficulties with implantable microelectrodes are evaluated, and solutions are presented from different perspectives. The latest advancements in microelectrode technology are reviewed and condensed, and future possibilities are explored.

Agriculture is a vital component of Egypt's economy; therefore, using Digital Elevation Models (DEMs) in agricultural planning in Egypt has significant benefits regarding water management, site appropriateness assessment, flood risk mitigation, and infrastructure construction. It is also essential for planners to make more informed decisions, optimize resource allocation, and support sustainable farming practices. This research paper investigates the accuracy of obtaining DEM data from four free global models (STRM30, ALOS30, COP30, and TanDEM-X90). The global DEM data has been compared to an actual GNSS-RTK DEM data surveyed onsite for two agricultural block areas in Aswan, the southern Government of Egypt. The two blocks are a part of a national project. For Block I and II, the RMSE of the Model STRM30 was 2.92 m and 3.59 m, respectively, indicating a poorer solution. Regarding accuracy, the ALOS30 model ranks third, reporting an RMSE of 2.58 m for block II and 3.30 m for block I. COP30 has an RMSE value of 1.06 m for blocks I and II and.91 m overall. TanDEM-X90 is the most accurate model in this investigation; block I provided an RMSE of 0.90 m with an SD of 0.58 m (SD95% = 0.38 m). After removing the anomalies, the model's stated RMSE for block II was 0.34 m, with an SD value of 0.62 m and 1.03 m. According to the classification using machine learning algorithms, with an accuracy of 84.7% for block I and 85% for block II, TanDEM-X90 is the best solution.

In recent years there has been a clear increase in bottled water consumption, globally which translates to significant health and environmental concerns. This cross-sectional study aims to understand the attitude and preferences of university students in Qatar towards use of bottled and tap water for drinking purposes using an online survey questionnaire. The number of students who responded to the online survey was 14% of the entire student population within the university (n = 688). Overall, majority of the students reported plastic bottled water as the main source of drinking water they preferred to use on campus (n=468; 68.02%), with a higher proportion of females (72.08%) preferring the use of plastic bottled water. Out of the 468 students who preferred plastic bottled water, safety was the most important factor (43.80%) followed by convenience (16.88%) and taste (15.60%). Cost (15.17%), personal/family habits (5.13%), Environmental concerns (2.14%) and minerals (1.28%) were found to be the least important factors. Among the 45 students who preferred tap water over plastic bottled water, cost (46.67%) was the dominant factor followed by convenience (20.00%) and environmental concerns and safety (13.33% each), taste (4.44%), and personal/family habits (2.22%). This study recommends campaigns to focus on attitude and behavior change and not solely emphasize knowledge; 71.7% believed that plastic water bottles are more harmful to the environment, yet the greater majority still resorted to this source. There is an immediate need to further educate students through environmental and health literacy programs on water consumption and quality. Enabling the population to understand the positive and negative aspects of their choices, may be an effective remedy to ensuring a healthy population and healthy environment.

Chronic inflammation, the activation of immune cells and their cross-talk with cardiomyocytes in the pathogenesis and progression of heart diseases has long been overlooked. However, with the latest research developments, it is increasingly accepted that a vicious cycle exists where cardiomyocytes release cardiocrine signaling molecules that spirals down to immune cell activation and chronic state of low‐level inflammation. For example, cardiocrine molecules released from injured or stressed cardiomyocytes can stimulate macrophages, dendritic cells, neutrophils and even T-cells, which then subsequently increase cardiac inflammation by co-stimulation and positive feedback-loops. One of the key proteins involved in stress-mediated cardiomyocyte signal transduction is a small GTPase RhoA. Importantly, the regulation of RhoA activation is critical for effective immune cell response and is being considered as one of the potential therapeutic targets in many immune-cell-mediated inflammatory diseases. In this review we provide an update on the role of RhoA at the juncture of immune cell activation, inflammation and cardiac disease.

The open communication is an exigent need for future power system where the time delay is unavoidable. In order to secure the stability of the grid, the frequency must remain within its limited range which is achieved through the load frequency control. The load frequency control signals are transmitted through communication networks which induces time delay that could destabilize the power systems. So, in order to guarantee the stability the delay margin should be computed. In this paper, we present a new method for calculating the delay margin in load frequency control systems. The transcendental time delay characteristics equation is transformed to frequency dependant equation. The spectral radius is used to find the frequencies at which the roots crosses the imaginary axis. The crossing frequencies are determined through the sweeping test and the binary iteration algorithm. A one-area load frequency control system is chosen as case study. The effectiveness of the proposed method has been proved through comparing with the most recent published methods. The method shows its merit with less conservativeness and less computations. The PI controller gains are preferable to be chosen large to reduce the damping, however, the delay margin decreases with increasing the PI controller gains.

The concept of a metaverse, a shared virtual space that brings together the physical and digital worlds, has been a topic of interest for decades. With recent advancements in technology, particularly in virtual reality (VR), augmented reality (AR), and blockchain, the metaverse has become a rapidly evolving and promising ecosystem. This paper provides a review of the metaverse, exploring its history, evolution, and current state of development. The paper delves into the different types of the metaverse, including fully immersive VR metaverses, hybrid metaverses that blend the physical and virtual worlds, and decentralized metaverses that are powered by blockchain. Additionally, the paper examines the impact of web 3.0 on the metaverse, as well as the various technologies used to create and sustain the metaverse, including VR, AR, and blockchain. Furthermore, the paper explores the concept of digital ownership and the potential for marketing and commerce within the metaverse. This paper serves as a review of the metaverse and its various components, providing insights into its history, development, and prospects, and is intended to provide a foundation for further research into this exciting and rapidly evolving ecosystem.

This research explores a novel approach to integrating offshore wind farms into smart microgrids through the development of an advanced model predictive control (MPC) strategy for offshore wind turbines. The MPC strategy comprehensively incorporates complex wind dynamics, such as wind speed, direction, and turbulence, ensuring an accurate representation of turbine behavior. Additionally, the research includes models addressing wind farm layout, wake effects, and electrical infrastructure, enhancing the modeling framework's fidelity and applicability to real-world offshore wind energy systems within a smart microgrid environment. The inherent variability of wind power, transmission technology limitations, and the need for seamless transitions between grid-connected and islanded operation modes in smart microgrids necessitate robust control mechanisms. These mechanisms ensure efficient power capture, grid stability, and optimal energy utilization. To tackle these challenges, the research proposes a smart microgrid design incorporating both AC-DC and DC-DC conversion technologies. This design leverages renewable energy sources like solar and wind with AC-DC conversion for efficient power capture, integrates DC energy storage systems to store excess energy during low demand periods, and utilizes power control mechanisms to manage energy flow effectively within the smart microgrid. The study emphasizes the importance of modeling and control strategies for both AC-DC and DC-DC converters within the smart microgrid framework. To enhance the microgrid's cost-effectiveness, priority is given to the utilization of solar PV energy sources. It also highlights the integration of protection systems for DC faults and coordinated control of AC/DC breakers and converters. This comprehensive approach aligns with the core principles of adaptability, reliability, and sustainability in smart grids, aiming to advance smart microgrid technologies and pave the way for a more resilient, efficient, and secure energy future.

Artificial Intelligence has transformed the cyber security industry by enabling organizations to systematize and enlarge outdated safety procedures. AI can provide more effective threat detection and response capabilities, enhance vulnerability management, and improve compliance and governance. AI technologies such as machine learning, natural language processing, behavioral analytics, and deep learning can enhance cyber security defenses and protect against a wide range of cyber threats, including malware, phishing attacks, and insider threats.Theoretical underpinnings of AI in cyber security, such as machine learning, natural language processing, behavioral analytics, and deep learning, are discussed. The advantages of using AI in cyber security are discussed including speed and accuracy, continuous learning and adaptation, and efficiency and scalability. It's important to note that AI is not a silver bullet for cyber security and should be used in conjunction with other security measures to provide a comprehensive defense strategy.AI has transformed the way cyber security operates in today's digital age. By analyzing vast amounts of data quickly and accurately it has become a valuable tool for organizations looking to protect their assets from cyber threats.

Background: Cyber security is used to save the important data from getting hacked, took by some unknown access. It makes our environment a safe place for us to work out or share our information and since privacy is almost everyone’s top priority, there must be the surety of saving the private information. Methods: In today’s world cyber security is really important as there are now many devices, websites, new technology which makes it a lot easier for hackers to get into anyone’s files which stores crucial data. However, many steps can be reserved to protect the data such as; educating your employees with how to prevent your files or computers from getting hacked, avoid clicking on websites that don’t seem safe, use firewalls, antimalware system and most importantly make sure to keep passwords that are hard to guess and try to go for a face recognition instead of pins and passcodes. Results and Conclusion: This all does not only makes using technology safe but also favors your business for the safety of employees working within the organization. The customers being assured about their data being safe, improves productivity since viruses can slow down computers which may trigger the focus of staff during the working hours. It could save your system from adware; the links of websites are also prevented from slow internet speeds. There is no denying at the fact that cyber security is a major requirement for everyone who is indulged with technology today.

Background: The outbreak of the Covid-19 pandemic has significantly affected the operations of higher education institutions. Due to the limited use of video conferencing and cloud computing in these facilities, distance learning became the only option available to them. Objective: The study focused on identifying the most common types of attacks that can affect e-learning assets. Results: There was a lack of clear cybersecurity policies for educational institutes and universities in 2020, according to a report by Microsoft Security Intelligence. The report showed that the education industry was the most targeted sector for malware attacks in the last 30 days. Conclusion: The recommendations for improving the security of e-learning systems. Some of these include implementing policies that restrict access to the resources and applications, updating security patches, and using cryptographic protocols.

Background: The rise of cloud computing has led to the increasing number of organizations that rely on it for various tasks and services, such as education, healthcare, and e-commerce. Unfortunately, many security threats can be caused by the sudden use of cloud platforms. Objective: This paper aims to provide a comprehensive overview of these threats and how they can be mitigated. Many companies are moving toward cloud computing to sustain their business growth and provide their employees with the best possible work environment. Results: Due to the rise of cyber security threats and the unprecedented number of breaches of data, small and medium-sized enterprises are also starting to take a huge leap. The outbreak of COVID-19 has affected the lives of people all around the world. Conclusion: Due to the seriousness of the situation, the WHO has declared the COVID-19 pandemic a public health emergency. To minimize the spread of the virus, the entire world has started adopting social distancing

The simultaneous evaluation of heat/mass transference procures momentous significance in the polymer industry and engineering activities. Extensive utilization of such aspects includes propylene flares, heat exchangers, energy transfiguration in chilling towers, and amputation of post fortuitous heat in nuclear reactors. Owing to such prospective demands, we interpreted the Jeffrey liquid reactive flow under non-linear convection. We scrutinized the transference of heat/mass under generalized Fourier-Fick relations. Thermal conductivity depends on temperature while mass diffusivity is dependent on concentration. Besides, heat source along with first-order chemical reaction aspects are accounted for. Relevant transformations are exerted to achieve non-linear differential systems that are solved through the homotopy scheme. Influences of divers factors are exhibited via graphical benchmark.

Since the 1980s, a growing interest in goat milk was noticed due to the nutritional values and health benefits of this milk, which resulted in increasing goat populations and milk production worldwide. This comprehensive review elaborates on goat milk composition compared to other types of milk. It is also an overview of goat milk production, properties, nourishment-value, applications in dairy products, and potential health benefits. Goat milk composition and its characteristics are slightly different from other types of milk and can be utilized to manufacture many dairy products. Fresh goat milk and goat milk products (e.g., yogurt and kefir were found to provide various potential health benefits, such as anti-inflammatory, prevent cardiovascular disease, anti-diabetic and antihypertensive, strengthen bones, boost immunity, and improve metabolism.

Abstract: The Tropical Rainfall Measuring Mission (TRMM) and then Global Precipitation Mission (GPM) are the most important and widely used data sources in the forecasting of drought, flood, and water resources management. However, since this sensor’s data is primarily used for tropical regions, it is necessary to evaluate the accuracy for optimal use of the data across varying climatic and physiographic conditions. In this study, the accuracy of the satellite data for a span of 17 years (2000-2017) for three climatic zones has been explored using synoptic ground station data. The climates include a) arid and low rainfall, b) semi-arid and low rainfall, and c) humid and high rainfall. We evaluated satellite data accuracy in drought and wet conditions based on the Standard Precipitation Index (S.P.I.) and different seasons. For available ground control stations, 13 stations were used in the humid, seven stations in a semi-arid climate, and 12 stations in the dry climate. The results show that the monthly precipitation product of GPM (IMERG product) and TRMM (TMPA/3B43 product) overestimate the rainfall. In the arid climate, the precipitation is estimated 43%, in the semi-arid environment 50%, and in the humid weather 11% more than the ground-based data on average. Therefore, to use satellite data in different climates, it is necessary to make corrections to obtain precise results. Based on 32 ground stations, the correction coefficient has a positive relationship with average precipitation and altitude and an inverse relationship with the latitude. Further in-depth investigations showed that the accuracy of satellite data in wet conditions is higher than the accuracy of normal circumstances, and the accuracy of normal conditions is more accurate than drought conditions. Besides, the accuracy of satellite data in wet or dry conditions increases with increasing time scales. The highest accuracy was obtained for a 12-month time scale and the lowest accuracy for the 3-month time scale of drought conditions in the arid climate.

Refinery planning optimization is a challenging problem as regards handling the nonconvex bilinearity mainly due to pooling operations in processes such as crude oil distillation and product blending. This work investigates the performance of several representative piecewise-linear (or piecewise-affine) relaxation schemes (referred to as McCormick, bm, nf5, nf6t, and de (which is a new approach proposed based on eigenvector decomposition) that mainly give rise to mixed-integer optimization programs to convexify a bilinear term using predetermined univariate partitioning for instances of uniform and non-uniform partition sizes. Computational results show that applying these schemes give improved relaxation tightness than only applying convex and concave envelopes as estimators. Uniform partition sizes typically perform better in terms of relaxation solution quality and convergence behavior. It is also seen that there is a limit on the number of partitions that contributes to relaxation tightness, which does not necessarily correspond to a larger number of partitions, while a direct relation between relaxation size and tightness does not always hold for non-uniform partition sizes.

Aravalli Mountain Range is an example of erosional mountains, trending NE-SW, shows numerous faults and lineaments. Udaipur area, situated south-east part of the mountain, is considered as tectonically active. So the main objective is to study relative tectonic activity of the Ahar watershed of Udaipur, Rajasthan, India. To assess relative tectonic activity of the area, geomorphic indices such as stream length gradient index (SL), asymmetry factor (Af), basin shape (Bs), valley floor width to valley height ratio (Vf), mountain front sinuosity (Smf), hypsometic integral (Hi), hypsometric curve and transverse topographic symmetry factor (T) is applied. DEM (SRTM), Google earth image and enhanced image of Landsat TM (2008) is used to extract linear features. Result of these geomorphic indices of each sub-watersheds are used to divide area from low to high relative tectonic activity classes, expressed as relative tectonic active index (Iat) and according to Iat value the sub watershed UDSW2, 3 and 4 is tectonically relatively more active than remaining part of the area. Field validation associated with evidences highlighted by using geomorphic indices as well as stream deflrction and lineament analysis reveals that the Ahar watershed of Aravalli Range, particularly the north-western flank, is most affected by tectonic activity.

: Digital communication is becoming an integral component of contemporary society and the use of mobile devices is increasing faster than ever. The function of message communication is becoming more popular as for mobile phone users, a short messaging service (SMS) requires an extremely high level of security. Any SMS that enters a person's smartphone must be considered a private affair, with privacy and security safeguarded. This research study found a novel Deoxyribonucleic acid (DNA) Cryptography method that uses a dynamic DNA sequence table to increase security. Cryptography is a popular approach for ensuring the confidentiality of a message. This paper proposed an Efficient Cryptographic Scheme for SMS (ECSS) algorithm to protect texts received from an Android smartphone. ECSS-based encryption has been identified as a novel method of securing information in the form of DNA molecules that employ DNA strands to conceal the information. This Paper provides the DNA cryptography approach for encrypting and decrypting plain texts in this work. The primary goal of ECSS cryptography is to guarantee secrecy when people transfer data across a network. This paper examines DNA Crypto, the distinction between classical cryptography and DNA Data encryption. An Android-based app is created to perform the proposed technique and the results show that the algorithms produce a consistent encryption result in which the length of the message before encryption is always the same as the length of the message after decryption. The suggested security solution has the potential to greatly improve the security of mobile communication. This Paper also provides experimental results for our chat application performance, such as received text message correctness, cipher text, average encryption time and average decryption time. According to the findings/results of this study, the speed of average encryption and decryption of the description is roughly 0.011 and 0.037 sec and prevents plaintext and dictionary attacks.

The impact of an unlicensed low-cost taxi in Bangladesh is very severe, especially in municipal cities. Day by day the numbers of unlicensed low-cost taxi are increasing by jumping up and creating pressure on traffic and transportation system. The aim of this study is to find out the causes of increasing illegal taxi and the extent of this vehicle in the municipalities of Bangladesh. Pabna municipality is used as a case study due to the more activeness of illegal taxi then the other municipalities. To achieve the objectives, the researcher used a qualitative approach to acquire more depth about the problems. Besides a direct observation of the study area, an open-ended questionnaire survey and HIS survey were conducted. The illegal low-cost taxi is very active it was analyzed through the field survey. A statistical model was developed to understand the actual causes of increasing illegal low-cost taxi, where ten predicted hypotheses (age, education level, marital status and family member support of illegal drivers, and the variable of commuter satisfaction e.g. safety, comfort, continuous service, affordability of service, reliability of service and driver behavior) were tested. The model was run through the multiple regression analyses technique in SPSS and the result proved that education level of illegal low-cost taxi drivers, and the commuter satisfaction variable (safety and comfort) had a positive and significant effect of increasing illegal low-cost taxi in the study area. However other variable had no significant effect in case of increasing illegal low-cost taxi. Besides the safety and comfort, steady job for the operators, provision of continuous, individual and door to door service system are the main reasons for increasing the illegal low-cost taxi in the study area. Finally, the researcher concludes with the requirement of some necessary action from the responsible authority on vehicular regulation for the improvement of the local public transport system in Bangladesh.

This study evaluated the using of machine vision in combination with deep learning to identify weeds in real-time for wheat production system. PMAS-Arid Agriculture university research farm were selected for collection of images (6000 total images) of weeds and wheat crops under different weather condition. During growing season, the database was constructed to identify the weeds. For this study two framework were used TensorFlow and PyTorch under CNNs and Deep learning. Deep learning perfromed better with in PyTourch value as compared to another model in Tensorflow. comparing with other networks such as YOLOv4, we concluded that our network reaches a better result between speed and accuracy. Specifically, the maximum precision of weed and wheat plants were 0.89 and 0.91 respectively with 9.43 ms and 12.38 ms inference time per image (640 × 640) NVIDIA RTX2070 GPU.

Carbon nanotubes (CNTs) possess unique mechanical, physical, electrical and absorbability properties coupled with their nanometer dimensional scale that renders them extremely valuable for applications in many fields including nanotechnology and chromatographic separation. The aim of this review is to provide an updated overview about the applications of CNTs in chiral and achiral separations of pharmaceuticals, biologics and chemicals. Chiral SWCNTs and MWCNTs have been directly applied for the enantioseparation of pharmaceuticals and biologicals by using them as stationary or pseudostationary phases in chromatographic separation techniques such as high-performance liquid chromatography (HPLC), capillary electrophoresis (CE) and gas chromatography (GC). Achiral MWCNTs have been used for achiral separations as efficient sorbent objects in solid-phase extraction techniques of biochemicals and drugs. Achiral SWCNTs have been applied in achiral separation of biological samples. Achiral SWCNTs and MWCNTs have been also successfully used to separate achiral mixtures of pharmaceuticals and chemicals. Collectively, functionalized CNTs have been indirectly applied in separation science by enhancing the enantioseparation of different chiral selectors whereas, non-functionalized CNTs have shown efficient capabilities for chiral separations by using techniques such as encapsulation or immobilization in polymer monolithic columns.

Increased construction activities in Australia have led to the generation of a massive volume of construction and demolition (C&D) waste annually. Management of this volume of waste requires an effective waste framework. The literature reported that the current Australian waste framework does not meet expectations and needs immediate improvements. This study was therefore conducted to seek the key C&D stakeholders' opinion about various issues identified in this waste stream. The specific objectives of this study are identification of the main barriers to effective C&D waste management, the impact of current regulations and opportunities to enhance the current C&D waste management system. A survey was conducted in 2019 to capture the stakeholders' perception. 132 participants from various industries and government agencies based in various Australian jurisdictions took part in the survey. The key results showed that the main barriers towards an effective management system are "overregulation, tough acceptance criteria, and increased testing requirements", "lack of local market" and "culture, poor education and low acceptance". Furthermore, a low number of participants indicated that the current legislation encourages waste recovery activities. The main areas of improvements included "providing a guideline that determines the accepted level of contamination for reusing C&D waste”, "preparation of guidelines on requirements of using recycled C&D materials in different industries" and "setting target for reduction, reusing, and recycling C&D waste". The results can inform policy development and be used as evidence for a broader discussion to solve lasting issues in C&D waste management.

Cellular immunotherapy has recently emerged as a fourth pillar in cancer treatment co-joining surgery, chemotherapy and radiotherapy. Where, the discovery of immune checkpoint blockage or inhibition (ICB/ICI), anti-PD-1/PD-L1 and anti-CTLA4-based, therapy has revolutionized the class of cancer treatment at a different level. However, still some cancer patient escape this immune surveillance mechanism and become resistant to ICB-therapy. Therefore, a more advanced or an alternative treatment is required instantly. Despite the functional importance of epitranscriptomics in diverse clinico-biological practices, its role in improving the efficacy of ICB therapeutics has been limited. Consequently, our study encapsulates the evidences, as a possible strategy, to improve the efficacy of ICB-therapy by co-targeting molecular checkpoints especially N6A-modification machineries which could be reformed into RNA modifying drugs (RMD). Here, we have explained the mechanism of individual RNA-modifiers (editor/writer, eraser/remover and effector/reader) in overcoming the issues associated with high-dose antibody toxicities and drug-resistance. Moreover, we have shed light on the importance of suppressor of cytokine signalling (SOCS/CISH) and microRNAs in improving the efficacy of ICB-therapy, with brief insight on the current monoclonal antibodies undergoing clinical trials or already approved against several solid tumor and metastatic cancers. We anticipate our investigation will encourage researchers and clinicians to further strengthen the efficacy of ICB-therapeutics by considering the importance of epitranscriptomics as a personalized medicine.

The traditional standards employed for pain assessment have many limitations. One such limitation is reliability because of inter-observer variability. Therefore, there have been many approaches to automate the task of pain recognition. Recently, deep-learning methods have appeared to solve many challenges, such as feature selection and cases with a small number of data sets. This study provides a systematic review of pain-recognition systems that are based on deep-learning models for the last two years only. Furthermore, it presents the major deep-learning methods that were used in review papers. Finally, it provides a discussion of the challenges and open issues.

The deposition of dust particles on solar panel modules constitutes a significant challenge, leading to a potential reduction in solar cell performance. This work tackles this issue by investigating the surface modification of a layer of transparent indium tin oxide (ITO), with a detailed analysis of the influence of its characteristics via different annealing conditions/processing. The ITO layer has been studied to enhance its characteristics for dust removal applications. Of particular note is that the developed ITO layer can be applied to dust removal using electrostatic or magnetic-based approaches. Thus, the correlation between annealing gas (using Argon, Oxygen, and Nitrogen), annealing temperature, and annealing ramping rate is explored with the obtained surface topography, as well as electrical and optical properties. The developed ITO layers annealed in the Argon medium at 600°C with an annealing ramping rate of 50°C/s showed smooth surface roughness, the highest electrical conductivity, and a relatively low refractive index. Such findings can play a crucial role in the future implementation of using the enhanced ITO layer for dust mitigation in solar panels, thus improving their long-term performance.

At present there is a renewed interest in theories of ”modified” gravity. Here, under a more drastic modification enforced by Galilei group, we obtain a completely new gravitational structure, and which exists in addition to the already available general relativity of today. Correlated with this, we show that in addition, there is a new ”modified” quantum mechanics, in as much as it exists as an independent and new ”pure” non-relativistic quantum me- chanics, and which has no relativistic counterpart. This is in addition to the present quantum mechanics, where the relativistic and non-relativistic structures are counterparts of each other. The above holds, firstly due to the correlation between Galilei group and quantum mechanics. These math- ematical conclusions are consolidated by the fact that there exists a physical Majorana interaction between each neutron- proton pairs in nuclei. Galilei invariance of Majorana exchange in Majorana interaction, shows that the mass here is of pure gravitational nature, and which is immune to the other three forces. This makes an amazing connection between the gravitational force and the quantum mechanics. This pure gravitational mass would man- ifest itself as dark matter of the universe. It is our new modified gravity that generates the dark matter.

The increasing global demand for efficient and sustainable energy storage solutions has driven the exploration of sulfur-based battery technologies. Sulfur’s abundance, low cost, and high theoretical energy density make it a promising candidate for next-generation energy storage, particularly in electric vehicles (EVs) and renewable energy systems. This paper reviews the development of sulfur-based batteries, including lithium-sulfur (Li-S), sodium-sulfur (Na-S), magnesium-sulfur (Mg-S), solid-state sulfur, sulfur-carbon nanocomposites, and hybrid sulfur flow batteries. Each technology is analyzed based on its advantages, challenges, and potential applications. Key research areas such as advanced electrolytes, nanomaterial integration, and sustainable manufacturing are highlighted, along with the current technological barriers to large-scale adoption. This review underscores the importance of continued research and innovation in sulfur-based battery technology to meet future energy storage demands.

IP Multimedia Subsystem (IMS) supports high-speed transmission of multi-media like data, audio, and video between mobiles and other wireless devices. IMS is the most suitable for multimedia communication across multiple networks using the Internet of Things (IoT) and cloud computing. IoT-IMS can efficiently manage the huge amount of data generated by smart devices for audio-video during live streaming applications. During these services, the main problem is that an intruder can launch a Session Initialization Protocol (SIP) messages flooding attack on IMS that does not have the functionality to prevent itself from these types of attacks. In this paper, an intrusion detecting and preventing system (IDPS) is proposed that effectively detects the register flooding and spoofing attacks using SIP messages. We proposed a watermark embedding algorithm on the user side and an extraction algorithm on receiving side. A test-bed is set up for IMS where we have considered four different scenarios to evaluate the IDPS approach as compared to counterparts. Results illustrate the dominance of our scheme in terms of response time, register flooding attack detection ratios, CPU load utilization, fault detection ratio, and memory utilization. The fault detection ratio averagely 98.18

The Internet of Things (also known as IoT), a revolution, has enhanced the relevance of mobile employees' job efficiency in mobile crowd sensing (MCS). Incentives based on reputation for mobile workers (MW) play an important role in increasing service utilization, motivating mobile employees, and developing confidence in the service. The cell phone is the most exploited entity in mobile crowd-sensing MCS and cloud computing. In the underlying investigation, we observed that they had not evaluated the complexity level of a task, resulting in a strong reputation for executing multiple basic tasks. A person who completes a tough task may have a lower reputation score. Complexity levels of tasks (CLT) were developed for reputation evaluation on a crowd-sensing network, which would be utilized to evaluate the MW reputation. We offered simple and complex levels of challenges to assess reputation scores. Tasks receive incentives based on their reputation. By measuring reputation on (CLT) complexity level of task, this research will help the system to Maintain the reputation of the mobile worker so that entities of the system get the maximum benefit out of it, by hiring well-reputed mobile workers and MW receive an incentive on it. Furthermore, we conduct a comparative analysis between our scheme and various machine learning algorithms to identify the algorithm that best performs in evaluating task complexity. Considering both the simple and complex reputation scores, the comparison suggests that after analyzing the data, it is clear that the CLT (proposed) scheme and the Linear regression scheme not only outperformed the Neural Network scheme in terms of Complex Reputation Scores but also in terms of Simple Reputation Scores. We also apply statistical tests, such as p-tests and t-tests, to determine the significance of the results obtained from different algorithms. Considering MW 308, MW 345, and MW 1045's efforts and abilities, the MCS system may offer incentives and awards to further motivate and consider their continuing contributions. This reputation-based incentivization technique not only encourages strong competition among mobile workers, but also makes sure the delivery of high-quality services inside the MCS system.

Photovoltaic is one of the promising renewable sources of power to meet the future challenge of energy need. Organic and perovskite thin film solar cells are an emerging cost-effective photovoltaic technology because of low-cost manufacturing processing and a light-weight. The main barrier of commercial use of organic and perovskite solar cells is the poor stability of devices. Encapsulation of these photovoltaic devices is one of the best ways to address this stability issue and enhance the device lifetime by employing materials and structures that possess high barrier performance for oxygen and moisture. The aim of this review paper is to find different encapsulation materials and techniques for perovskite and organic solar cells according to the present understanding of reliability issues. It discusses the available encapsulate materials and their utility in limiting chemicals such as water vapour, oxygen penetration. It also covers the mechanisms of mechanical degradation within the individual layers and solar cell as a whole, and possible obstacles to their application in both organic and perovskite solar cells. The contemporary understanding of these degradation mechanisms, their interplay and their initiating factors (both internal and external) are also discussed.

: This study aims at exploring Turkish consumers’ behaviors toward purchasing green fashion. A mixed-methods approach was used in this study. Six experts from the main brands in the fashion industry in Türkiye were interviewed. A total of 268 questionnaires were collected from Turkish consumers, and their responses were analyzed. The theory of planned behavior (TPB) informed the theoretical framework of this study. The main components of the TPB were extended to include perceived consumer effectiveness. A thematic analysis was conducted to analyze and code the interviews. To test the hypotheses, structural equation modeling (SEM) was conducted. The findings show that the key factors of the TPB, i.e., attitudes (ATTs), subjective norms (SNs), and perceived behavioral control (PBC), as well as perceived consumer effectiveness, significantly impact the intentions of Turkish consumers to purchase sustainable fashion. However, the results highlight some inconsistencies, gaps, and barriers that discourage the purchase intentions of consumers, including a lack of information, misinformation, greenwashing, green skepticism, a lack of trust, and the high cost of sustainable fashion.

As yin and yang, cancer and diabetes are metabolic disorders characterized by deregulated, yet opposing, metabolic alterations. These metabolic shifts reflect a complex network of defective underlying signaling pathways, which ultimately orchestrate both disease pathogenesis and progression. The Warburg effect portrays the chief metabolic phenotype in cancer and is reflected by the dominance of aerobic glycolysis over minimal-to-no viable oxidative phosphorylation in cancer. Conversely, during the pathogenesis of type 2 diabetes (T2D), oxidative phosphorylation is constantly heightened. In advanced insulin resistance and T2D, the metabolic landscape becomes more complex, with exacerbating metabolic alterations affecting oxidative phosphorylation in a tissue-specific manner. Promising nutritional adjuvants, such as alpha-lipoic acid and flavonoids, can reprogram metabolism and exert antitumor and antidiabetic effects. Other pharmacological agents, such as metformin, have therapeutic effects on cancer and T2D. Herein, we discuss the molecular mechanisms and signaling pathways involved in the metabolic shifts in cancer and T2D, and explore the therapeutic strategies under investigation that aim to reverse the metabolic shift in both disease scenarios.

Dendritic cells (DCs) are the professional antigen-presenting cells that recognize and present antigens to naïve T cells to induce antigen-specific adaptive immunity. Among the T-cell subsets, T helper type 2 (Th2) cells produce the humoral immune responses required for protection against helminthic disease by activating B cells. DCs induce a Th2 immune response at a certain immune environment. Basophil, eosinophil, mast cells, and type 2 innate lymphoid cells also induce Th2 immunity. However, in the case of DCs, controversy remains regarding which subsets of DCs induce Th2 immunity, which genes in DCs are directly or indirectly involved in inducing Th2 immunity, and the detailed mechanisms underlying induction, regulation, or maintenance of the DC-mediated Th2 immunity against allergic environments and parasite infection. A recent study has shown that a genetic defect in DCs causes an enhanced Th2 immunity leading to a severe atopic dermatitis. We summarize the Th2 immune-inducing DC subsets, the genetic and environmental factors which involved in DC-mediated Th2 immunity, and current therapeutic approaches for Th2-mediated immune disorders. This review is to provide an improved understanding of DC-mediated Th2 immunity and Th1/Th2 immune balancing, leading to control over their adverse consequences.

Human papillomavirus (HPV) infections, primarily transmitted through sexual contact, have been linked to various cancers, including cervical, penile, anal, oropharynx, breast, and prostate cancers. This study presents a unique case of concurrent high-risk HPV35, HPV45, and HPV59 infections in both prostate and bladder cancer tissues from a single patient, representing the first documented instance worldwide with identical HPV types detected in two adjacent organs of the same individual. Employing a multiplex-PCR approach, gel electrophoresis, and Sanger sequencing, we confirmed the presence of these high-risk HPV types. Additionally, Western blot analysis using an HPV E7 antibody demonstrated the active expression of HPV oncoproteins in both cancer types. This discovery underscores the potential for HPV intra-organ transmission and necessitates further exploration of alternative transmission routes. The implications of our results offer new insights into the complex dynamics of HPV transmission in cancer pathogenesis.

For a considerable length of time synthetic composts are utilized to satisfy the dirt necessity of supplements and yield, however huge measure of these substance manures are hazardous for condition, advantageous microorganisms, creatures, and people also. In this way, natural inviting and savvy biofertilizers are utilized. Biofertilizer are the substances which contain microorganisms those microorganisms might be growths, microscopic organisms, and protozoa which have capacity to build ripeness of soil by Nitrogen obsession, Phosphorous solubilization, and Iron sequestration. These cycles convert insoluble type of supplements into solvent structure and make it accessible to the foundations of plant which effectively take them up and use them. There are assortment of the yields whose profitability can be expanded by applying biofertilizer, for example, rice, oat, and other grain crops. In this audit we experience the method of utilization of biofertilizers, and how the assistance the plants and in which they help.

The current report contributes to the understanding of the stereoselectivity of the chiral dirhodium(II) carboxylate catalysts derived from N-protected amino acid ligands. Investigating the possible effect of ligand stereo-purity on catalyst structure and enantioselectivity was carried out. This was justified through a new X-ray crystal structure for Rh2(S,S,S,R-PTTL)4 diastereomer.

Tuberculosis (TB) associated stigma is well-documented phenomenon that may contribute to sub-optimal TB care in Pakistan. The objective of study was to assess TB related knowledge and perceived stigma among community members. This was cross-sectional survey using convenience sample of 183 individuals recruited between October and December 2017. A validated stigma measurement tool developed by Van Rie et al. was adapted. Data was analyzed using SPSS version 20.0. 183 individuals (73% males; n = 134) participated in survey. Eighty-seven percent were aware that TB is curable disease (n = 159) and 91% thought that it could be transmitted by coughing (n = 167). However, respondents also thought that TB was spread through contaminated food (73%; n = 134), sharing meals (55%; n = 100), sharing utensils (53%; n = 96) and by having sexual intercourse with a TB patient (51%; n = 93). Fifty-seven percent (n = 104) associated TB with high levels of stigma. Persons who had less than six years of education (crude OR = 1.2; 95% CI: 0.89, 1.72) and lacked knowledge that TB is curable (crude OR = 3.42; 95% CI: 1.20, 9.70) were more likely to associate TB with stigma. In addition, females (crude OR = 1.33; 95% CI: 0.87, 2.04) and those who were unemployed (crude OR = 1.06; 95% CI: 0.65, 1.74) were also more likely to associate TB with stigma. We found an association between lack of knowledge about TB and perceived stigma. This highlights need for improved education and awareness about TB.