Lithium-ion batteries (LIBs) have become indispensable energy storage devices for various applications, ranging from portable electronics to electric vehicles and renewable energy systems. The performance and reliability of LIBs depend on several key components, including the electrodes, separators, and electrolytes. Among these, the choice of binder materials for the electrodes plays a critical role in determining the overall performance and durability of LIBs. This review introduces polymer binders that have been traditionally used in the cathode, anode, and separator materials of LIBs. Furthermore, it explores the problems identified in traditional polymer binders and examines the research trends in next-generation polymer binder materials for lithium-ion battery as alternatives.

In this study, we aimed to identify blood lymphocytes as a prognostic factor for survival in patients with locally advanced stage III non-small cell lung cancer (NSCLC) treated with concurrent chemoradiotherapy (CCRT). We conducted a secondary analysis of 196 patients enrolled in the Korean Radiation Oncology Group 0903 phase III clinical trial to evaluate the prognostic significance of circulating blood lymphocyte levels. The median total lymphocyte count (TLC) reduction ratio during CCRT was 0.74 (range: 0.29 – 0.97). In multivariate analysis, patient age (p = 0.014) and gross tumor volume (GTV, p = 0.031) were significant factors associated with overall survival, while TLC reduction (p = 0.018) and pretreatment neutrophil-to-lymphocyte ratio (NLR; p = 0.010) were associated with progression-free survival (PFS). In multivariate logistic regression analysis, pretreatment NLR, GTV, and heart V20 were significantly associated with TLC reduction. TLC reduction during CCRT is a significant prognostic factor for PFS, and heart V20 is significantly associated with TLC reduction. Thus, constraining the volume of the radiation dose to the whole heart must be prioritized to reduce TLC.

This article analyzes the Franco-Spanish invasion of Vietnam from 1858 to 1860. Research is based on documents such as correspondence, reports, archives and diplomatic treaties as well as monographs from the time France intended to invade Vietnam through missionary activities until the end of the Franco-Spanish invasion. The article focuses on three basic issues that are the causes of the alliance, the evolution of the French and Spanish coalition invasion in Vietnam and its impact on stakeholders. The research results on the Franco-Spanish invasion of Vietnam indicated that the invasion carried out by this alliance was more special than that of the other French coalitions before. The invasion was based on an alliance without any commitment to the interests and responsibilities of the parties. The goals of France and Spain in this invasion were different. That led to conflict between France and Spain during the invasion and the fall of the alliance. France achieved its goal through an invasion that turned Vietnam into a colony, while Spain had barely achieved its desire to have commercial and missionary interests in the area.

Effective and rapid mixing is essential for various chemical and biological assays. The present work reports a simple and low-cost micromixer based on magnetofluidic actuation. The device takes advantage of magnetoconvective secondary flow, a bulk flow induced by an external magnetic field, for mixing. A paramagnetic stream of diluted ferrofluid and a non-magnetic stream are introduced to a straight microchannel. A permanent magnet placed next to the microchannel induced a non-uniform magnetic field. The magnetic field gradient and the mismatch in magnetic susceptibility between the two streams create a body force, which leads to rapid and efficient mixing. The micromixer reported here could achieve a high throughput and a high mixing efficiency of 90 % in a relatively short microchannel.

: The primary objective of this study was to investigate the association of certain genetic alterations and intraoperative fluorescent activity of 5-aminolevulinic acid (ALA) in brain metastasis (BM) of lung adenocarcinoma. A retrospective cohort study was conducted among 72 patients who underwent surgical resection of BM from lung adenocarcinoma at our institute for 5 years. Cancer cell infiltration was estimated by the intraoperative fluorescent activity of 5-ALA, and genetic alterations were analyzed by next-generation sequencing (NGS). The sensitivity and specificity for detecting cancer cell infiltration using 5-ALA were 87.5% and 96.4%, respectively. Genes associated with cell cycle regulation (p = 0.003) and cell proliferation (p = 0.044) were significantly associated with positive fluorescence activity of 5-ALA in the adjacent brain tissue. Genetic alterations in cell cycle regulation and cell proliferation were also associated with shorter recurrence-free survival (p = 0.013 and p = 0.042, respectively) and overall survival (p = 0.026 and p = 0.042, respectively) in the multivariate analysis. The results suggest that genetic alterations in cell cycle regulation and cell proliferation are associated with positive fluorescence activity of 5-ALA in the adjacent infiltrative brain tissue and influence the clinical outcome of BM of lung adenocarcinoma.

The effect of γ-ray irradiation on surface plasmon resonance (SPR) sensing capability of refractive index (n = 1.418–1.448) of the silica glass optical fiber comprised of germano-silicate glass cladding embedded with Au nano-particles (NPs) was investigated. As the γ-ray irradiation increased from 1 hour to 3 hours with the dose rate of 1,190 Gy/h, the morphology of the Au NPs and the SPR spectrum were found to change. The average diameter of Au NPs increased with the aspect ratio from 1 to 2 and the nano-particles became grown to the clusters. The SPR peak wavelength shifted towards longer wavelength with the increase of total dose of γ-ray irradiation regardless of the corresponding refractive indices. The SPR sensitivities (wavelength/refractive index unit, nm/RIU) also increased from 407 nm/RIU to 3,553 nm/RIU, 1,483 nm/RIU, and 2,335 nm/RIU after the γ-ray irradiation at the total dose of 1,190 Gy, 2,380 Gy, and 3,570 Gy, respectively.

Short-range Internet of Things (IoT) sensor nodes operating at 2.4 GHz need to provide ubiquitous wireless sensor networks (WSNs) with energy-efficient, wide-range output power (POUT) and fully integrated on a single chip for wireless body area networks (WBANs) and wireless personal area networks (WPANs) using low-power Bluetooth (BLE) and Zigbee standards. The proposed fully integrated transmitter (TX) utilizes a digitally controllable current-mode class-D (CMCD) power amplifier (PA) with a second harmonic distortion (HD2) suppression to reduce VCO pulling in an integrated system while meeting harmonic limit regulations. The CMCD PA is divided into 7-bit slices that can be reconfigured between differential and single-ended topologies. Duty cycle distortion compensation is performed for HD2 suppression, and an HD2 rejection filter and a modified C-L-C low-pass filter (LPF) reduce HD2 further. Implemented in a 28 nm CMOS process, the TX achieves a wide POUT range of from 12.1 to -31 dBm and provides a maximum efficiency of 39.8% while consuming 41.1 mW at 12.1 dBm POUT. The calibrated HD2 level is -82.2 dBc at 9.93 dBm POUT, resulting in a transmitter figure of merit (TX_FoM) of -97.52 dB. Higher order harmonic levels remain below -41.2 dBm even at 12.1 dBm POUT, meeting regulatory requirements.

Coronary artery disease (CAD) is a prevalent cardiovascular condition characterized by the accumulation of plaque within coronary arteries. This plaque accumulation obstructs blood flow to the heart, resulting in a heart attack. While distinct features of CAD have been identified, its causes remain largely unclear, with the exception of environmental and nutritional factors. This study aimed to investigate the connection between genetic factors and CAD, focusing on the thymidylate synthase (TS) gene, a gene involved in one-carbon metabolism. Therefore, our research targeted single nucleotide polymorphisms that could potentially impact TS gene expression and lead to dysfunction. Our findings strongly associate the TS 1100T>C and 1170A>G genotypes with CAD susceptibility. We observed that TS 1100T>C polymorphisms increased disease susceptibility in several groups, while the TS 1170A>G polymorphism displayed a decreasing trend for disease risk when interacting with clinical factors. Furthermore, our results demonstrate the potential contribution of the TS 1100/1170 haplotypes to disease susceptibility, indicating a synergistic interaction with clinical factors in disease occurrence. Based on these findings, we propose that polymorphisms in the 3'-UTR miRNA binding site of the TS gene could serve as clinically useful biomarkers for the prevention, prognosis, and management of CAD.

This study aims to understand the global environment of COVID-19 management and guide future policy directions after the pandemic crisis. To this end, we analyzed a series of the World Economic Forum’s COVID-19 response reports through text mining and network analysis. These reports, written by experts in diverse fields, discuss multidimensional changes in socioeconomic situations, various problems created by those changes, and strategies to respond to national crises. Based on 3,897 refined words drawn from a morphological analysis of 26 reports (as of the end of 2020), this study analyzes the frequency of words, the relationships among words, the importance of specific documents, and the connection centrality through text mining. In addition, network analysis helps develop strategies for sustainable response to and management of national crises through identifying clusters of words with a similar structural equivalence.

(1) Background: The aim of this study was to investigate the circadian rhythms of tongue features according to the effects of physiological phases over a 24-hour period. (2) Methods: Fifteen healthy participants aged 20 to 69 years were recruited. The participants did not have current chronic diseases or past diseases and had to meet the inclusion and exclusion criteria. The participants stayed at the Gil Hospital for a duration of 2 nights and 3 days. On the first day, at 18:00, they consumed their allocated portions of food and water and then completed a questionnaire. At approximately 21:00, their tongue images were acquired using a computerized tongue image acquisition system, following which they slept for 8 hours, commencing at 23:00. Measurements were taken from 07:00 through 21:00 on the second day, and the final acquisition was taken at 07:00 on the following morning, resulting in a total of eight images. The circadian rhythm was authenticated and quantified utilizing the single cosinor analysis, a technique for periodic regression analysis for fitting a 24-hour cosine curve. (3) Results: Cosinor analysis revealed that all tongue features were significantly related to circadian rhythm. (4) Conclusions: The results of this study may be important for considering the time of day at which the tongue is observed and tongue status is evaluated.

Vascular cell adhesion molecule-1 (VCAM-1) is closely associated with tumor progression and metastasis. However, the relevance and role of VCAM-1 in lung cancer have not been clearly elucidated. In this study, we found that VCAM-1 was highly overexpressed in lung cancer tissue compared with that of normal lung, and high VCAM-1 expression correlated with poor survival of lung cancer patients. VCAM-1 knockdown reduced invasion in A549 human lung cancer cells, and competitive blocking experiments targeting the Ig-like domain 6 of VCAM-1 (VCAM-1-D6) demonstrated that the VCAM-1-D6 domain was critical for VCAM-1-mediated A549 cell invasion. Next, we developed a human monoclonal antibody specific to human and mouse VCAM-1-D6 (VCAM-1-D6 huMab), which was isolated from a human synthetic antibody library using phage display technology. Finally, we showed that VCAM-1-D6 huMab had a nanomolar affinity for VCAM-1-D6 and that it potently suppressed invasion in A549 and NCI-H1299 lung cancer cell lines. Taken together, these results suggest that VCAM-1-D6 is a novel therapeutic target in VCAM-1-mediated lung cancer invasion and that our newly developed VCAM-1-D6 huMab will be a useful tool for inhibiting VCAM-1-expressing lung cancer cell invasion.

Gravity played an important role in the development of life on earth. The effect of gravity on a living organisms can be investigated by controlling the magnitude of gravity. Most reduced gravity experiments are conducted on the lower earth orbit (LEO) in the International Space Station (ISS). However, running experiments in ISS face challenges such as high cost, extreme condition, lack of direct accessibility, and long waiting period. Therefore, researchers have developed various ground-based devices and methods to perform reduced gravity experiments. However, the search for life outside the earth requires more intensive research. Advancements in conventional methods and the development of new tools are required for this purpose. The advantages of Lab-on-a-Chip (LOC) devices make them an attractive option for simulating microgravity. This paper briefly reviews the advancement of LOC technologies for simulating microgravity in a earth-based laboratory.

Surface acoustic wave (SAW) is effective for the manipulation of fluids and particles in microscale. The current approach of integrating interdigitated transducers (IDTs) for SAW generation into microfluidic channels involves complex and laborious microfabrication steps. These steps often require the full access to clean room facilities and hours to align the transducers to the precise location. This work presents an affordable and innovative method for fabricating SAW-based microfluidic devices without the need of clean room facilities and alignment. The IDTs and microfluidic channels are fabricated in the same process and thus precisely self-aligned in accordance with the device design. With the use of the developed fabrication approach, a few types of different SAW-based microfluidic devices have been fabricated and demonstrated for particle separation and active droplet generation.

Interior permanent magnets motors are widely used in applications requiring high power den-sity and high efficiency due to their high torque generating capabilities. Recently, given the re-cent price fluctuations and unstable supply of rare-earth permanent magnets, alternative config-urations with reduced use of permanent magnets are being sought. Among the various candi-dates related to this, the consequent-pole type rotor structure can halve the number of perma-nent magnets used compared with conventional structures. However, in the no-load analysis, the waveform of the back electromotive force becomes asymmetric, generating a harmonic component. As a result, there is a disadvantage that the torque ripple increases. To overcome these shortcomings, we propose a novel rotor structure that applies a consequent-pole structure to an embedded permanent-magnet motor structure, wherein a number of permanent magnets are arranged in a flared structure to constitute a single polarity. In the proposed flared-structured magnet arrangement, it is possible to adjust the angle of the permanent magnet and the polar angle to mitigate the asymmetry of the back EMF waveform. The proposed struc-ture was optimized with a genetic algorithm and a prototype of the optimal model was con-structed and experimentally evaluated to verify its validity. Finally, the performance improve-ment and validity of the proposed structure were verified by comparing the analysis results of the optimal model with the experimental results.

Large lithium-ion batteries (LIBs) in electric vehicles and energy storage systems demonstrate different performance and lifetime compared to small LIB cells, owing to the size effects generated by the electrical configuration and property imbalance. However, the calculation time for performing life predictions with three-dimensional (3D) cell models is undesirably long. In this paper, a lumped cell model with equivalent resistances (LER cell model) is proposed as a reduced order model of the 3D cell model, which enables accurate and fast life predictions of large LIBs. The developed LER cell model is validated via the comparisons with results of the 3D cell models by simulating a 20-Ah commercial pouch cell (NCM/graphite) and the experimental values. In addition, the LER cell models are applied to different cell types and sizes, such as a 20-Ah cylindrical cell and a 60-Ah pouch cell.

An effective method for coating textile fabrics with porous materials is proposed, and the removal rates of nitrogen oxides (NOx), sulfur oxides (SOx), and fine dust particles in the coated textile fabrics are evaluated. The textile fabrics made of polyester are used to effectively reduce fine dust particles through static electricity. Zeolite and coconut shell activated carbon are used as porous material to reduce SOx and NOx, respectively. The effects of the epoxy content and dilution solution types on the SOx removal rate of textile fabrics coated with zeolite are evaluated to determine the optimum coating conditions. In addition, the effects of external environmental conditions, such as washing and freeze thawing, on the SOx and NOx removal rates of the textile fabrics coated with porous materials using the optimum coating conditions are examined. The test results show that the SOx removal rate of textile fabrics coated with zeolite decreases with the increase in the epoxy content. The decrease is 2.9 times larger for textile fabrics coated using deionized water than those coated using isopropyl alcohol. After one wash, the SOx removal rate decreases dramatically. However, the decrease is reduced by 16% when the epoxy content ratio is increased by 0.5%. The effects of washing and freeze thawing on the SOx and NOx removal rates of textile fabrics coated using the deionized water diluted with the epoxy content ratio of 2% are minimal. Consequently, to maintain stable SOx and NOx removal rates under external environmental conditions such as washing and freeze thawing, 98% deionized water dilution and 2% epoxy content ratio are required for the optimum coating of textile fabrics with zeolite and coconut shell activated carbon.

Paper-based analytical devices have been substantially developed in recent decades. Many fabrication techniques for paper-based analytical devices have been demonstrated and reported. Herein we report a relatively rapid, simple, and inexpensive method for fabricating paper-based analytical devices using parafilm hot pressing. We studied and optimized the effect of the key fabrication parameters, namely pressure, temperature, and pressing time. We discerned the optimal conditions, including pressure of 3.8 MPa (3 tons), temperature of 80oC, and 3 minutes of pressing time, with the smallest hydrophobic barrier size (821 µm) being governed by laminate mask and parafilm dispersal from pressure and heat. Physical and biochemical properties were evaluated to substantiate the paper functionality for analytical devices. Wicking speed in the fabricated paper strips was slightly slower than that of non-processed paper, resulting from reducing paper pore size. A colorimetric immunological assay was performed to demonstrate the protein binding capacity of the paper-based device after exposure to pressure and heat from the fabrication. Moreover, mixing in two-dimensional paper-based device and flowing in a three-dimensional counterpart were thoroughly investigated, demonstrating that the paper device from this fabrication process is potentially applicable as analytical devices for biomolecule detection. Fast, easy, and inexpensive parafilm hot press fabrication presents an opportunity for researchers to develop paper-based analytical devices in resource-limited environments.

Hydrostatic bearings for liquid rocket engine turbopumps provide distinctive advantages including high load capacity even with low viscosity cryogenic fluid and extending a life span by minimizing friction and wear between rotor and bearing surfaces. Application of hydrostatic bearings into turbopumps demands reliable test data base with well-quantified operating parameters and experimentally validated accurate performance predictive tools. The present paper shows the comprehensive experimental data and validation of predicted static load characteristics of hydrostatic journal bearings lubricated with air, water, and liquid nitrogen. Extensive experiments for static load characteristics of hydrostatic bearings are conducted using a turbopump rotor-bearing system simulator while increasing supply pressure (Ps) into the test bearings. The test results demonstrate notable effects of the test fluids and their temperatures, as well as Ps, on the bearing performance. In general, the measured bearing flow rate, rotor displacement, and stiffness of the test bearings steadily increase with Ps. The static load bearing characteristics predictions considering flow turbulence and compressibility matched well with the experimental results. The work with an independent test data and engineering computational programs will further the implementation of hydrostatic bearings in high performance turbopump shaft systems with improved efficiency and enhanced reusability of liquid rocket engine sub-systems.

Microstructured surfaces are renowned for their unique properties, such as waterproofing and low adhesion, making them highly applicable in the biomedical field. These surfaces play a crucial role in influencing cell response by mimicking the native microenvironment of biological tissues. In this study, we engineered a series of biomimetic micropatterned surfaces using polydimethylsiloxane (PDMS) to explore their effects on primary breast cancer cell lines, contrasting these effects with those observed on conventional flat surfaces. The surface topography was varied to direct cells’ attachment, growth, and morphology. Our findings elucidate that surface-free energy is not merely a background factor but plays a decisive role in cell dynamics, strongly correlating with the spreading behaviour of breast cancer cells. Notably, on micropillar surfaces with high surface-free energy, an increase in the population of cancer cells was observed. Conversely, surfaces characterised by lower surface-free energies noted a reduction in cell viability. Moreover, the structural parameters, such as the gaps and diameters of the pillars, were found to critically influence cellular dispersion and adherence, underscoring the importance of the microstructures’ topography in biomedical applications. These insights pave the way for designing advanced microstructured surfaces tailored to specific cellular responses, opening new avenues for targeted cancer therapies and tissue engineering.

This article explored how some state policies on rehabilitation, protection and utilization of mangroves are implemented at two locals; namely, Ca Mau provice and its sub-unit Ngoc Hien District as well as Ho Chi Minh City and its sub-unit Can Gio District and what are considered as emgerging issues in the implementation process. The study employed mixed research methods including document and thematic analysis, in-depth interviews, and group discussion. The findings showed that state policies would be adapted through the ways in which these two locals manage to silmultaneously orient their work toward accommodating the madates placed upon them and cope with the reality of socio-economic difficulties at their levels. The findings also showed some issues that need to consider addressing; namely, locals’ struggles to fill the gaps between written and implemented policies in mangrove rehabilitation, conflict among sectors and stakeholders in mangrove utilization and protection, problems in guaranteeing adequate budget for in-need-locals, inconsistence in policies on "forest: water surface” ratio in mangrove-shrimp farm, and unintended consequences in forest thinning and exploitation regimes. Based on the finding analysis, the articles discussed lessons learned from the policy implementation process on mangrove rehabilitation, management and forest allocation to household in the south of Vietnam.

Dermal interstitial fluid (ISF) is a novel source of biomarkers that can be considered as an alternative to blood sampling for disease diagnosis and treatment. Nevertheless, in vivo extraction and analysis of ISF are challenging. On the other hand, microneedle (MN) technology can address most of the challenges associated with dermal ISF extraction and is well-suited for long-term, continuous ISF monitoring as well as in situ detection. In this review, we first briefly summarise the different dermal ISF collection methods and compare them with MN methods. Next, we elaborate on the design considerations and biocompatibility of MNs. Subsequently, the fabrication technologies of various MNs used for dermal ISF extraction, including solid MNs, hollow MNs, porous MNs and hydrogel MNs, are thoroughly explained. In addition, different sensing mechanisms of ISF detection will be discussed in detail. Subsequently, we identify the challenges and propose the possible solutions associated with ISF extraction. A detailed investigation is provided for the transport and sampling mechanism of ISF in vivo. Also, the current in vitro skin model integrated with the MN arrays will be discussed. Finally, future directions to develop a point-of-care (POC) device to sample ISF are proposed.

The common dolphin is the second most bycaught species in Korean waters. To provide key information about their habitat boundaries and hotspots for spatial conservation and management, the spatial use of this species was examined using data obtained from sighting and bycatch surveys of cetacean during the past 20 years. The 95% minimum convex polygon and 95% density contour of fixed kernel suggested that the boundary of home range of common dolphins is limited to the coastal region (Busan-Sokcho) of the East Sea/Sea of Japan. From 50% density contours dawn by kernel density estimation, it was suggested that their hotspots are around the cost of Ulsan-Pohang, Doghae, and Sokcho within the home range. Common dolphins are not at all distributed in the Yellow Sea. Hence, shallow waters, such as the coastal region of the Yellow Sea, are not suitable habitats for common dolphins.

Various peptides or non-structural amino acids are recognized by their specific target proteins and perform biological role in various pathways in vivo. Understanding the interactions between target protein and peptides (or non-structural amino acids) provides key information on the molecular interactions, which can be potentially translated to the development of novel drugs. However, it is experimentally challenging to determine the crystal structure of protein-peptide complexes. To obtain structural information on substrate recognition of peptide-recognizing enzyme, X-ray crystallographic studies were performed using triglycine (Gly-Gly-Gly) as main-chain of peptide. The crystal structure of Parengyodontium album Proteinase K in complex with triglcyine was determined at 1.4 Å resolution. Two different bound conformations of triglycine were observed at the substrate recognition site. The triglycine backbone forms stable interactions with β5-α4 and α5-β6 loops of main-chain. One of the triglycine-binding conformations was identical with the binding mode of a peptide-based inhibitor from a previously reported crystal structure of Proteinase K. Triglycine has potential application X-ray crystallography to identify substrate recognition sites in peptide binding enzymes.

The KcsA is a prokaryotic potassium-oriented channel, which is sourced from the Streptomyces lividans soil bacteria. From extensive studies that have been carried over the KcsA potassium channel, it has been proved that various factors enable the gating and shuttling of the potassium ions into and out of the cells. Some of the factors include the different concentration of protons in the inside and outside membrane. The other factor is the existence of the selectivity filter equipped in the exit of channel pore, which enables the movement of the K⁺ ions. Not only are potassium ions present in the channel but also sodium ions. Potassium and sodium ions are the ions that are essential in the conductivity of a cell because of their charge. An intuitive idea about why K⁺ ions are at least 10,000 times more permeant than Na⁺ ions is presented in various entities. The hypothesis is that the selectivity ratio is probably related to the successive entry of Na⁺ ions, based on the premise that the ratio seems to be relevant to unpredictable quantities caused by Brownian corrosion of ions.

In this study, the model proposed by Yang et al. to generalize the stress–strain model for unconfined concrete with consideration of the size effect is expanded. Sim et al.’s compressive strength model that is based on the function of specimen width and aspect ratio was used for the maximum stress. In addition, a strain at the maximum stress was formulated as a function of compressive strength by considering the size effect using the regression analysis of datasets compiled from a wide variety of specimens. The descending branch after the peak stress was formulated with consideration of less dissipated area of fracture energy with the increase in specimen width and aspect ratio in the compression damage zone (CDZ) model. The key parameter for the slope of the descending branch was formulated as a function of specimen width and aspect ratio, concrete density, and compressive strength of concrete considering the size effect. Consequently, a rational stress–strain model for unconfined concrete was proposed. This model explains the trends of the peak stress and strain at the peak stress to decrease and the slope of the descending branch to increase, as the specimen width and aspect ratio increase. The proposed model agrees well with the test results, irrespective of the compressive strength of concrete, concrete type, specimen width and aspect ratio. In particular, the proposed model for the stress–strain curve rationally considered the effect of decreasing peak stress and increasing the descending branch slope, with the increase in specimen width and aspect ratio.

Nonsteroidal anti-inflammatory drugs (NSAIDs), which block the activity of cyclooxygenase (COX) isoenzymes and inhibit the synthesis of prostaglandin, have been used for pain relief. We have developed a method to separate a mixture of three NSAIDs, such as aspirin, paracetamol, and naproxen, using reverse-phase high-performance liquid chromatography (RP-HPLC). An isocratic mobile phase consisting of acidic water and acetonitrile was selected to run at a low flow rate, such as 0.8 mL/min. The mixture of three NSAIDs was injected at a low volume into a C18 column that was 150 mm in length and characterized using a UV detector at 230 nm. We identified three peaks in the chromatogram indicating the three compounds. The elution time of the peaks was less than 10 minutes. To identify multiple peaks on the isocratic flow using a short column, further studies are required regarding the proposed method to generate microfluidic devices for nanoLC.

In the field of visualization, understanding users’ analytical process is important to determine the effectiveness of a designed visualization application. To understand the users’ analytical process, numerous studies have been performed to capture and analyze user interactions. Although many studies have emphasized the importance of analyzing user interactions to understand users’ analytical reasoning processes, few have successfully linked these interactions to users’ reasoning processes. This paper introduces an approach that bridges this gap by correlating semantic user interactions with analysis decisions through an interactive wire transaction analysis system and a visual state transition matrix. With the designed analysis system, interactive analysis can be performed to evaluate financial fraud in wire transactions. It also allows the mapping of captured user interactions and analytical decisions back onto the visualization, revealing users’ distinct results. The visual state transition matrix further aids to help understanding users’ analytical flows, revealing their decision-making processes. Classification machine learning algorithms are applied to assess the effectiveness of our approach in understanding analysts’ strategies by connecting them to their decisions. From the study, we observed an average of 72% accuracy in clearly classifying the semantic user interactions. For classifying individual decisions, we observed an average of 70% classification accuracy. This emphasizes the importance of capturing semantic user interactions to understand users’ analytical processes. Overall, it is determined that the proposed approach not only enhances the understanding of analytical behaviors but also offers a robust approach for evaluating user interactions in visualization tools.

For the effective utilization of rice husk, organosolv fractionation was investigated to separate three main components (glucan, xylose, and lignin) with low acid concentration. Reaction temperatures of 170–190 °C, ethanol concentrations of 50–70% (v/v), and sulfuric acid concentrations of 0–0.7% (w/v) were investigated, with the reaction time and liquid-to-solid ratio kept constant at 60 min and 10, respectively. The fractionation conditions for the efficient separation into the three components of rice husk were determined to be 180 °C, 60% (v/v) of ethanol, and 0.25% (w/v) of sulfuric acid. Under these fractionation conditions, 86.8% of the xylan and 77.5% of the lignin were removed from the rice husk, and xylose and lignin were obtained from the liquid in 67.6% and 49.8% yields, respectively. The glucan digestibility of the fractionated rice husk was 85.2% with an enzyme loading of 15 FPU (filter paper unit) of cellulase per g-glucan.

In order to produce bioethanol from yellow poplar sawdust without detoxification, deacetylation (mild alkali treatment) was performed with aqueous ammonia solution. To select the optimal conditions, deacetylation process was carried out using different conditions: NH₄OH loading (2–10% (w/v)) and solid-to-liquid ratio (1:4–10) at 121 °C for 60 min. In order to assess the effectiveness of deacetylation, fractionation of deacetylated yellow poplar sawdust was performed using dilute acid (H₂SO₄, 0.5–2.0% (w/v)), reaction temperature (130–150 °C) and time (10–80 min). The toxicity-reduced hemicellulosic hydrolysates that were obtained through a two-step treatment at optimized conditions were fermented using Pichia stipitis for ethanol production, without any further detoxification. The maximum ethanol production was 4.84 g/L, corresponding to a theoretical ethanol yield of 82.52%, which is comparable to those of intentionally made hydrolyzates as controls.

This study investigated the relationship of acrosome reactions and fatty acid composition on fertility in boar sperm. The acrosome reaction of sperm was induced via methyl-beta-cyclodextrin (MBCD), and acrosome reaction, plasma membrane integrity, and fertility were analyzed. The fatty acid composition of the excess acrosome reacted sperm was determined via gas chromatography. The results showed that the acrosome reaction in sperm was induced over 85% of the time by 60 mM MBCD treatment, and the plasma membrane integrity was significantly decreased and was dependent on the MBCD level. The acrosome reacted sperm resulted in significantly higher saturated fatty acids (SFAs) and lower unsaturated fatty acids (PUFAs) than the non-acrosome reaction group. Moreover, the acrosome reacted sperm from 60 mM MBCD significantly decreased in vitro fertility and blastocyst formation relative to non-acrosome reacted sperm, and the acrosome reaction was positively correlated with SFAs and negatively correlated with PUFAs. Of these fatty acids, C22:5n-6 (docosapentaenoic acid [DPA]) and C22:6n-3 (docosahexaenoic acid [DHA]) were directly negatively correlated with the acrosome reaction (r = -0.982 and -0.947, respectively). In conclusion, the excessive acrosome reactions may occur by reducing the PUFAs, which may then dramatically decrease sperm fertility in pigs.

.Purpose: This paper presents a comparative analysis of state-of-the-art DIR algorithms in the context of head and neck squamous cell carcinoma (HNSCC) radiation therapy. Materials and Methods: We used a dataset of head and neck cancer patients within the Cancer Image Archive, which includes 31 patients with 3D CT image data from pre-treatment, mid-treatment, and post-treatment stages of radiotherapy. We applied DIR algorithms to two datasets, one for pre-treatment to mid-treatment registration and another for mid-treatment to post-treatment registration, by aligning one CT image to another CT image. To quantitatively analyze the patient data, we focused on the spinal cord, optic nerve, brain stem, cochlea, and PTV as the OAR datasets. To verify the DIR algorithm, we used two non-learning-based methods, SyN and NiftyReg, as well as three deep learning-based methods, Voxelmorph, Cyclemorph, and Transmorph. We trained a deep learning model by adjusting the ratio of the training dataset, validation dataset, and test dataset to 7:1:2. Results: The average DSCs of SyN and NiftyReg, the non-learning-based methods, were 0.74±0.06 and 0.70±0.12, respectively. The deep learning-based methods, Voxelmorph, Cyclemorph, and Transmorph, had average DSCs of 0.72±0.08, 0.68±0.11, and 0.69±0.13, respectively. The deep learning DIR algorithm produced transformed outputs of OAR/PTV in a shorter time than other models, including commercial and conventional mathematical algorithms (At Inference(sec/images), Voxelmorph: 0.36, Cyclemorph: 0.3, Transmorph: 5.1, SyN: 140, NiftyReg: 40.2). Conclusions: In conclusion, our study provides a comprehensive comparison of commercial DIR algorithms with traditional and deep learning-based DIR methods. Our results demonstrate that commercial DIR algorithms outperform traditional DIR methods in terms of accuracy and efficiency. However, we also show that deep learning-based DIR methods have the potential to achieve similar performance to commercial algorithms with proper training and optimization. Our findings suggest that both commercial and deep learning-based DIR methods have their respective advantages and limitations, and the choice of method should depend on the specific requirements of the clinical application. Overall, our study contributes to ongoing efforts to improve the accuracy and efficiency of DIR methods for better patient outcomes.

Land use/land cover (LULC) and climate changes are two main factors directly affecting hydrologic conditions. However, very few studies in Vietnam have investigated changes in hydrological process under the impact of climate and land use changes on a basin scale. The objective of this study is to assess the individual and combined impacts of land use and climate changes on hydrological processes for the Nam Rom river basin, Northwestern Viet Nam using Remote Sensing (RS) and Soil and Water Assessment Tools (SWAT) model. SWAT model was used for hydrological process simulation. Results indicated that SWAT proved to be a powerful tool in simulating the impacts of land use and climate change on catchment hydrology. The change in historical land use between 1992 and 2015 strongly contributed to increasing hydrological processes (ET, percolation, ground water, and water yield), whereas, climate change led to significant decrease of all hydrological components. The combination of land use and climate changes significantly reduced surface runoff (-16.9%), ground water (-5.7%), water yield (-9.2%), and sediment load (-4.9%). Overall climatic changes had more significant effect on hydrological components than land use changes in the Nam Rom river basin during the 1992–2015. Under impacts of projected land use and climate change scenarios in 2030 on hydrological process of the upper Nam Rom river basin indicate that ET and surface flow are more sensitive to the changes in land use and climate in the future. In conclusion, the findings of this study will basic knowledge of the effects of climate and land-use changes on the hydrology for future development of integrated land use and water management practices in Nam Rom river basin.

The protein extract of Ulva australis hydrolyzed with alcalase and flavourzyme investigated multi-functional properties, including total antioxidant capacity (TAC), collagenase inhibitory and antibacterial activities. The #5 fraction (SP5) and #7 fraction (SP7) of U. australis hydrolysate from cation-exchange chromatography showed significantly high TAC, collagenase inhibitory and antibacterial effects against Propionibacterium acnes, and only Q3 fraction from anion-exchange chromatography showed high multi-functional activities. The eight peptides among 42 peptides identified by MALDI-TOF/MS and Q-TOF/MS/MS were selected from the results to screen molecular docking on target proteins, and were synthesized. Thr-Gly-Thr-Trp (TGTW) showed ABTS [2,2′-azino-bis (3-ethylbenzothiazoline-6-sulfonic acid)] radical scavenging activity. Effect TAC as Trolox equivalence was dependent on the concentration of TGTW. The Asn-Arg-Asp-Tyr (NRDY) and Arg-Asp-Arg-Phe (RDRF) possessing collagenase inhibitory activity increased according to the increase of concentration and the IC50 values of them were 0.95 mM and 0.84 mM, respectively. Peptides, RDRF and His-Ala-Val-Tyr (HAVY) showed anti-P. acnes effects with IC50 values of 8.57 mM and 13.23 mM, respectively. These results suggest that the U. australis hydrolysate could be a resource for the application of effective nutraceuticals and cosmetics.

The purpose of this study is to explore the effects of dual-task training, including cognitive tasks, on cognitive and bodily functioning and β-amyloid levels in Alzheimer's dementia patients. The subjects were 34 inpatients diagnosed with Alzheimer's dementia at a nursing hospital located in Gyeongsansi, South Korea. The patients were randomly divided into a dual-task group (n = 16) and a single-task group (n = 18). The dual-task group performed cognitive tasks at the same time as exercising tasks, while the single-task group performed only exercise tasks. Each group was trained for 30 minutes three times a week for eight weeks. The Mini-Mental State Examination was used to measure the patients’ cognitive function. Static and dynamic balance were measured to evaluate bodily functioning. Static balance was measured using Biorescue, while dynamic balance was measured using the Berg Balance Scale. Blood analysis was performed to measure levels of β-amyloid, which is known to cause Alzheimer's dementia. Both groups exhibited statistically significant improvements in gait function after the training (p < .05). The dual-task group exhibited statistically significant differences in cognitive function, static and dynamic balance function, and β-amyloid levels after training (p < .05). A significant difference was observed between the two groups (p < .05). Dual-task activities were found to be effective in improving cognitive and bodily functioning and reducing β-amyloid levels in Alzheimer's dementia patients. Therefore, dual-task training is thought to be an effective method of treating and preventing Alzheimer's dementia.

This study aimed to assess the diagnostic accuracy of a mobile application by comparing its diagnoses to those of Orofacial Pain and Oral Medicine specialists and further imaging results (TMJ CBCT and MRI) in 500 patients with temporomandibular disorder (TMD). The research focused on three diagnostic categories: initial specialist diagnoses, final diagnoses after imaging, and the mobile app's diagnoses. The concordance rate, sensitivity, specificity, and positive predictive value of the diagnoses were examined, with further imaging serving as the gold standard. The mobile app demonstrated a high concordance rate compared to both final (0.93) and initial specialist diagnoses (0.86). Sensitivity, specificity, and positive predictive values also indicated strong reliability, affirming the app's diagnostic validity. Although the concordance rate was slightly lower when comparing the app's diagnoses to imaging results (CBCT and MRI), specialist diagnoses yielded similar results. The study suggests that user-friendly diagnostic mobile applications, based on the Diagnostic Criteria for Temporomandibular Disorders, could enhance the clinical management of TMD. Given the reliability of mobile applications for diagnostic purposes, their wider implementation could facilitate the provision of appropriate and timely treatments for patients with TMD.

The low relative humidity (RH) levels in a greenhouse during the daytime in a strawberry (Fragaria × ananassa Duch) cultivation period negatively affect the growth of strawberry related to photo-physiology. Therefore, this study was conducted to confirm an efficient RH management method by analyzing the phenotypic characteristics related to photo-physiology by controlling the RH in a greenhouse during the daytime with a fog system. Strawberry plants were grown respectively in a greenhouse affected by natural RH changes (control) and in a greenhouse with 40% ~ 50% RH adjusted during the daytime using a fog system. In the greenhouse, with controlled RH, the temperature decreased, and the RH was higher in the initial growth stage of strawberry planting than the control. It was observed a significant increase in the survival rate of the strawberry plant, as well as the incidence of powdery mildew, was lowered. In addition, the photosynthetic rate and OJIP chlorophyll a fluorescence transients related to photosystem II efficiency of strawberry leaves were significantly higher in the fog treatment than in the control. In winter, during the day, the number of days on which the temperature dropped below 20℃ has increased, the greenhouse temperature with controlled RH was lower due to the fog system. When the yield per strawberry plant in January and February was investigated, the control was higher than the RH treatment. Therefore, RH management using a fog system must be controlled at a level where a temperature range is adequate for plant growth, in which the efficient control of these parameters increases strawberry productivity.

Candida albicans is an opportunistic fungus that becomes pathogenic and problematic under certain biological conditions. C.albicans may cause painful and uncomfortable symptoms, as well as deaths in immunocompromised patients. Therefore, early detection of c.albicans is essential. However, conventional detection methods are costly, slow and inaccessible to women in remote or developing areas. To address these concerns, we have developed a wearable and discrete naked-eye detectable, colorimetric platform for c.albicans detection. With some modification, this platform is designed to be directly adhered to existing feminine hygiene pads. Our platform is rapid, inexpensive, user-friendly, disposable and only requires three steps: i) addition of vaginal fluid onto sample pads; ii) addition of gold nanoparticle gel and running buffer, and iii) naked eye detection. Our platform is underpinned by selective thiolated aptamer-based recognition of 1,3-β-D glucan molecules- a hallmark of c.albicans cell walls. In the absence of c.albicans, wearable sample pads turn bright pink. In the presence of c. albicans, the wearable pads turn dark blue due to significant nanoparticle target-induced aggregation. We demonstrate naked eye colorimetric detection of 4.4 ×106 c.albicans cells per ml. We believe that this proof-of-concept platform has the potential to have a significant impact on women’s health, globally.

Flow sensing in hostile environment is of increasing interest for applications in automotive, aerospace, and chemical and resource industries. Compared to their counterparts, thermal flow sensors are attractive candidates due to the ease of fabrication, lack of moving parts and higher sensitivity. Recently, a number of thermal flow sensor prototypes have been reported in the literature demonstrating the measurement of fluid flows under hostile conditions. This paper summarizes the concept of thermal flow sensing, operational modes and transduction mechanisms. Then, the choice of materials and their corresponding properties are presented in details. The paper also reports recent progress in the development of thermal flow sensors for harsh environment. In addition, the issues and considerations in packaging are reviewed. Finally, we conclude the review with the future prospects.

The plant Allium hookeri, belonging to the Allium genus, has a history of being used both as a common food ingredient and in herbal medicine. It has recently been reported to have anti-oxidant and anti-inflammatory effects. A. hookeri has been also shown to exhibit neuroprotective and anti-neuroinflammatory activities, but the active compounds responsible for these effects have not been identified in previous studies. This study aimed to perform a metabolite profiling using an HRESI-qTOF MS/MS-based molecular networking approach and identify the active compounds from A. hookeri that target senescent cell-associated secretory phenotype (SASP) inhibitory effects, which contribute to neuroprotective activities. As a result, ten compounds, including one new flavonoid (2) and nine known compounds (1 and 3–10), were identified, and their biological activity was tested. The most potent compound was N-trans-feruloyltyramine (7), which inhibited SASP markers and contributed to the senomorphic activities of A. hookeri. These findings suggest that the phenolamides from A. hookeri could be a promising source of bioactive compounds for preventing senescence-associated diseases.

Singing melody extraction is the task that identifies the melody pitch contour of singing voice from polyphonic music. Most of the traditional melody extraction algorithms are based on calculating salient pitch candidates or separating the melody source from the mixture. Recently, classification-based approach based on deep learning has drawn much attentions. In this paper, we present a classification-based singing melody extraction model using deep convolutional neural networks. The proposed model consists of a singing pitch extractor (SPE) and a singing voice activity detector (SVAD). The SPE is trained to predict a high-resolution pitch label of singing voice from a short segment of spectrogram. This allows the model to predict highly continuous curves. The melody contour is smoothed further by post-processing the output of the melody extractor. The SVAD is trained to determine if a long segment of mel-spectrogram contains a singing voice. This often produces voice false alarm errors around the boundary of singing segments. We reduced them by exploiting the output of the SPE. Finally, we evaluate the proposed melody extraction model on several public datasets. The results show that the proposed model is comparable to state-of-the-art algorithms.

Water is a limited resource that needs to be properly managed and distributed to the ever-growing population of the world. Rapid urbanization and development have drastically increased the overall water demand worldwide. Ageing water distribution networks are vulnerable to deterioration and leakage, thereby causing an estimated annual loss of about 48 trillion liters of water. To address these issues, efficient and reliable leakage detection and management techniques are necessary. In this paper, the results of the experiments performed on a looped water distribution network in AnSeong, Korea are discussed. Transient-based techniques were used and physical data were collected for the detection and localization of leakages in the experimental water pipes. The results obtained from the experiments demonstrated the applicability of transient techniques for leak analysis in looped water distribution networks.

Water distribution networks are vital infrastructure, needed for providing consumers with sufficient water of appropriate quality. The cost of construction, operation, and maintenance of such networks is extremely large. The problem of optimization of a water distribution network is governed by the type of water distribution network and the size of pipelines placed in the distribution network. This problem of the optimal diameter allocation of pipes in a distribution network has been heavily researched over the past few decades. This study describes the development of a computer program, ‘Smart Optimization Program for Water Distribution Networks’ (SOP–WDN), which applies Genetic Algorithm to the problem of the least-cost design of water distribution networks. SOP–WDN demonstrates the application of an evolutionary optimization technique, Genetic Algorithm, linked with a hydraulic simulation solver EPANET, for the optimal design of water distribution networks. The developed program was applied to three benchmark water distribution network optimization problems and produced consistently good results. SOP–WDN can be utilized as a tool for guiding engineers during the design and rehabilitation of water distribution pipelines.

Background: This study investigated how the expression of heat shock protein 27 (HSP27), cellular FLICE-like inhibitory protein (cFLIP) and clusterin (CLU) affects the progression of cancer cells and their susceptibility to doxazosin-induced apoptosis. By silencing each of these genes individually, their effect on prostate cancer cell viability after doxazosin treatment was investigated. Methods: PC-3 prostate cancer cells were cultured and then subjected to gene silencing using siRNA targeting HSP27, cFLIP, and CLU, either individually, in pairs, or all together. Cells were then treated with doxazosin at various concentrations and their viability was assessed by MTT assay. Results: The study found that silencing the CLU gene in PC-3 cells significantly reduced cell viability after treatment with 25 µM doxazosin. In addition, dual silencing of cFLIP and CLU decreased cell viability at 10 µM doxazosin. Notably, silencing all three genes of HSP27, cFLIP, CLU was most effective and reduced cell viability even at a lower doxazosin concentration of 1 µM. Conclusions: Taken together, these findings suggest that simultaneous silencing of HSP27, cFLIP, and CLU genes may be a potential strategy to promote apoptosis in prostate cancer cells, which could inform future research on treatments for malignant prostate cancer.

Codium fragile, a green algae, exhibit biological properties. In this study, we examined the effect of Codium fragile extract (CFE) on dextran sulfate sodium (DSS)-induced colitis. As the administration of CFE increased, the proliferation of Akkermansia muciniphila, which is key player in metabolic and gastrointestinal disorders, increased. After CFE administration for 10 weeks, acetic acid was revealed as the major metabolite in mouse cecum and β-glucuronidase activity in mouse feces is decreased. Further, CFE significantly alleviates the acute intestinal injury induced by DSS administration, including DAI scores and colon length. MPO activity in the colon was significantly reduced in the CFE-fed group, which indicated that CFE could inhibit neutrophils infiltration and inflammation in mice. In conclusion, a protective effect of CFE against DSS colitis suggests its clinical use for IBD patients.

Partial negative allosteric modulators (NAM) of the mGlu5 receptor are an excellent alternative to full antagonists and NAMs because they retain some therapeutic effects and, at the same time, have a much broader therapeutic window. Here, we investigated whether partial mGlu5 NAM, M-5MPEP induced a fast and sustained antidepressant-like effect, characteristic of rapid-acting antidepressant drugs (RAADs) like ketamine, in C57BL/6J mice. M-5MPEP caused a rapid, dose-dependent antidepressant-like action in the tail suspension test (TST) 60 min after injection. This effect was antagonized by an AMPA receptor antagonist (NBQX) and a TrkB receptor antagonist (ANA-12) but not by 5HT1A and 5HT2A/2C receptor antagonists. Furthermore, M-5MPEP (30 mg/kg) induced sustained antidepressant-like effects 24 h after the last of four administrations. These effects were revealed in the splash test, designed to measure apathy-like state, and in the TST. Western blot and ELISA analyses indicated the involvement of the TrkB/BDNF pathway in the sustained M-5MPEP effects. Additionally, prolonged effects of M-5MPEP were entirely reversed by the TrkB receptor antagonist ANA-12 in both the splash test and the TST, confirming the critical role of TrkB receptor activation in the sustained antidepressant-like effect of M-5MPEP. Importantly, M-5MPEP enhanced the subthreshold dose of (R)-ketamine in the TST, indicating both substances' convergent mechanisms of action and the possibility of their practical use in treating depression.

Existing rammed earth construction methods have disadvantages such as increased initial costs for manufacturing the large formwork and increased labor costs owing to the labor-intensive construction techniques involved. To address the limitations of existing rammed earth construction methods, an autonomous rammed earth construction method is introduced herein. As this autonomous rammed earth construction method uses a modular formwork, alternative materials must be used in the construction to satisfy the requirements for the early-age binder performance. Accordingly, this study evaluates the use of an epoxy emulsion composed of epoxy and a hardener to enhance the performance of the binder. Preliminary experiments were conducted to determine the optimal formulation of the epoxy emulsion, following which the compressive strength, water loosening, shrinkage, rate of mass change, and microstructure of several red clay binder specimens with and without epoxy emulsion were analyzed at early ages. The results confirmed that the epoxy emulsion can be applied to satisfy the performance requirements for autonomous rammed earth construction by improving the durability and strength of the binder at early ages.

Plant-derived compounds have been historically used for the treatment of various diseases and an important source of several clinically useful anti-cancer agents. The Artemisia annua is known as a medicinal herb that is effective against cancer. Thus, the purpose of this study was to investigate whether ethanol extracts of Artemisia annua could increase an anti-cancer effect against LS174T cells. Our results show that Artemisia annua extracts (AAE) induces apoptosis through the regulation of mitochondria outer membrane potential. We demonstrate that apoptosis is induced by p53-dependent manner when cells were treated with Nutlin-3 (MDM2 inhibitor) and LY294002 (Akt inhibitor). In addition, the apoptotic effect was also observed in the p53-independent manner through pifithrin-α (p53 inhibitor) and celecoxib (COX-2 inhibitor) treatment. As in in vitro, AAE induced apoptotic effects and regulated apoptosis-related proteins in LS174T xenograft model. Taken together, these results suggest that Artemisia annua extracts exerts an anti-cancer effect through p53-independent manner, as well as p53-dependent manner by p53´ translocation in LS174T colon cancer cells.

In South Korea, in line with the increasing need for a reliable water supply following the continuous increase in water demand, the Smart Water Grid Research Group (SWGRG) was officially launched in 2012. With the vision of providing water welfare at a national level, SWGRG incorporated information and communications technology in its water resource management, aiming at the development of core technologies for a Smart Water Grid consisting of intelligent microgrids and a demonstration and tests of the developed technologies through a field operation in a living lab. The living lab was built in Block 112 of YeongJong Island, Incheon, South Korea (area of 17.4 km2, population of 8,000), where Incheon International Airport, a hub of Northeast Asia, is located. In this location, water is supplied through a single submarine pipeline, making the place optimal for responses to water crises and the construction of a water supply system during emergencies. From 2017 to 2019, ultrasonic wave type smart water meters and IEEE 802.15.4g advanced metering infrastructure (AMI) networks were installed at 527 sites of 958 consumer areas in the living lab, and core element technologies (intelligent water source management and distribution system, smart water distribution network planning/control/operation strategy establishment, AMI network and device development, integrated management of bi-directional smart water information), and operation solutions (smart water statistics information, real-time demand-supply analysis, decision support system, real-time hydraulic pipeline network analysis, smart DB management, and water information mobile application) were developed through a field operation and testing.

Serial femtosecond crystallography (SFX) using an X-ray free-electron laser (XFEL) enables determination of room-temperature structures without causing radiation damage. Using an optical pump-probe or mix-and-injection, SFX enables the intermediate state visualization of a molecular reaction. In SFX experiments, serial and stable microcrystal delivery to the X-ray interaction point is vital for reasonable data collection and efficient beam time. The Pohang Accelerator Laboratory X-ray Free Electron Laser (PAL-XFEL) facility established SFX instruments at a nanocrystallography and coherent imaging (NCI) experimental station. Various sample delivery methods, including injection, fixed-target scanning, and hybrid methods, have been developed and applied to collect XFEL diffraction data. Herein, we review the currently available sample delivery methods for SFX at the NCI experimental station at the PAL-XFEL. This article will help PAL-XFEL users access the SFX system for their experiments.

Non-Orthogonal Multiple Access (NOMA) is the key technology promised to be applied in next-generation networks in the near future. In this study, we propose a multi-points cooperative relaying (MPCR) NOMA model instead of just using a relay as the previous studies. Based on the channel state information (CSI), the base station (BS) selects a closest user equipment (UE) and sends a superposed signal to this UE as a first relay node. We have assumed that there are N UEs in the network and Nth UE, which is farthest from BS, has the poorest quality signal transmitted from the BS compared other UEs. Nth UE received the forwarded signal from N-1 relaying nodes that are UEs with better signal quality. At the ith relaying node, it detect its own symbol by using successive interference cancellation (SIC) and will forward the composite signal to the next closest user, namely i+1th UE, and include an excess power which will use for energy harvesting (EH) intention at the next UE. By these, the farthest UE in network can be significantly improved. In addition, closed-form expressions of outage probability for users over both the Rayleigh and Nakagami-m fading channels are also presented. Analysis and simulation results performed by Matlab software which are presented accurately and clearly show that the effectiveness of our proposed model and this model consistents with the multi-access wireless network in future.

A form of dementia distinct from healthy cognitive aging, Alzheimer's disease (AD) is a complex multi-stage disease that currently afflicts over 50 million people worldwide. Unfortunately, previous therapeutic strategies developed from murine models emulating different aspects of AD pathogenesis have failed. Consequently, researchers are now developing models that express several aspects of pathogenesis that better reflect the clinical situation in humans. As such, this review seeks to provide insight regarding current applications of mammalian models in AD research by addressing recent developments and characterizations of prominent transgenic models and their contributions to pathogenesis as well as discuss the advantages, limitations, and application of emerging models (hAβ-KI) that better capture genetic heterogeneity and mixed pathologies observed in the clinical situation.

Plasma plays an important role in semiconductor processes. With the recent miniature and integration, the control of plasma became essential for the success in critical dimension of a few nanometers and etch narrow and deep holes with high aspect ratios. Recently, the etching process has reached physical limitations due to a significant increase in wafer surface temperature under the elevated amount of RF power, affecting not only the warpage phenomenon but also etching uniformity and etching profiles. Therefore, the plasma characteristics are identified using invasive single Langmuir probe (SLP) for wafer temperature diagnosis. Optical data is obtained through a non-invasive optical emission spectroscopy (OES) and the plasma parameters are derived to compare and verify with the SLP. Two variables, electron temperature and electron density, are substituted for the heat flux formula to derive the heat flux according to its location. Using a wafer-type temperature sensor, check the derived heat flux values and compare trends. Such studies are expected to be able to calculate heat flux values in real time, anticipate wafer temperatures, and solve existing problems.

With the increasing demand for precise condition monitoring and diagnosis of gas-insulated switchgears (GIS), it has become a challenge to improve the detection sensitivity of partial discharge (PD) induced in the GIS spacer. This paper deals with the elimination of the capacitive component from the phase resolved partial discharge (PRPD) signal generated in GIS spacer based on the discrete wavelet transform. Three types of typical insulation defects were simulated using PD cells. The single PD pulses were detected and were further used to determine the optimal mother wavelet. As a result, the bior6.8 was selected to decompose the PD signal into 8 levels and the signal energy at each level was calculated. The decomposed components related with capacitive disturbance were discarded whereas those associated with PD were de-noised by a threshold and a thresholding function. Finally, the PRPD signals were reconstructed using the de-noised components.

Radiotherapy for cancer has been known to affect the responses of immune cells, especially those of CD8+ T cells that play a pivotal role in anti-tumor immunity. Clinical success of immune checkpoint inhibitors led to an increasing interest into the ability of radiation to modulate CD8+ T cell responses. Recent studies that carefully analyzed the CD8+ T cell responses following radiotherapy suggest the beneficial roles of radiotherapy on anti-tumor immunity. In addition, numerous clinical trials that evaluate the efficacy of combining radiotherapy with immune checkpoint inhibitors are undergoing. In this review, we summarize the current status of knowledge regarding the changes of CD8+ T cells following radiotherapy from various preclinical and clinical studies. Furthermore, key biologic mechanisms that underlie such modulation, including both direct and indirect effects, are described. Lastly, we discuss the current evidence and essential considerations for harnessing radiotherapy as a combination partner for immune checkpoint inhibitors.

This paper reports the design, development, and testing of a novel, yet simple and low-cost portable device for the rapid detection of SARS-CoV-2. The device performs loop mediated isothermal amplification (LAMP) and provides visually distinguishable images of the fluorescence emitted from the samples. The device utilises an aluminium block embedded with a cartridge heater for isothermal heating of the sample and a single-board computer and camera for fluorescence detection. The device demonstrates promising results within 20 minutes using clinically relevant starting concentrations of the synthetic template. Time-to-signal data for this device are considerably lower compared to standard qPCR machine (~10-20 minutes vs &gt;38 minutes) for 1×105 starting template copy number. The device in its fully optimized and characterized state can potentially be used as simple to operate, rapid, sensitive, and inexpensive platform for population screening as well as point-of-need SARS-CoV-2 detection and patient management.

We performed Bayesian network meta-analysis (NMA) to suggest frontline treatments for patients with high PD-L1 expression (at least 50%). A total of 5,237 patients from 22 studies were included in this NMA. In terms of progression-free survival, immune checkpoint inhibitors (ICIs) plus bevacizumab plus chemotherapy had the highest surface under the cumulative ranking curve (SUCRA) value (98.1%), followed by ICI plus chemotherapy (82.9%). In terms of overall survival (OS), dual immunotherapy plus chemotherapy had the highest SUCRA value (79.1%), followed by ICI plus bevacizumab plus chemotherapy (73.4%). However, there was no significant difference of survival outcomes among treatment regimens combined with immunotherapy. Moreover, ICI plus chemotherapy failed to reveal a significant OS superiority to ICI monotherapy (hazard ratio = 0.978, 95% credible internal: 0.771-1.259). In conclusion, this NMA indicates that ICI plus chemotherapy with/without bevacizumab might to be the best options in terms of OS for NSCLC with high PD-L1 expression. Considering there was no significant difference of survival outcomes among treatment regimens incorporating immunotherapy and ICI plus chemotherapy failed to show significant survival benefits over ICI monotherapy, however, ICI monotherapy may be reasonable as first-line treatment for advanced NSCLC with high PD-L1 expression and no targetable aberrations.

Fluid flow in human body is generally known to influence a variety of cellular behaviors. Different nanoparticle properties as well as cell type, interaction with other cells and cellular environments also show significant effect on nanoparticle uptake and drug efficacy. The aim of this study was to evaluate the effect of shear stress on cellular behaviors of biocompatible and biodegradable nanoparticles to cancer cells (A549 cell lines) in a biomimetic microfluidic system. We prepared a gelatin-oleic conjugate (GOC) as an amphiphilic biomaterial to prepare self-assembled gelatin-oleic nanoparticles (GON). Coumarin-6 and paclitaxel were used as the fluorescence marker and model drug, respectively, and were loaded into GONs by incubation (C-GONs; PTX-GONs). Additionally, we evaluated the cellular uptake of fluorescence labeled C-GONs and the drug efficacy of PTX-GONs. The cellular uptake of C-GONs by A549 cells in the absence of shear stress revealed that the mean fluorescence intensity was slightly decreased compared to that in the presence of shear stress. The results also indicated that negatively charged PTX-GONs had a lower cancer killing effect under dynamic conditions than that under static conditions. It also suggested that fluidic shear stress did not significantly affect drug uptake and efficiency in case of PTX-GONs. The cellular interactions between nanoparticles and cells in drug delivery should be carefully examined according to the physicochemical properties of nanoparticles such as the type of materials, size and mainly surface charge in a biomimetic microfluidic condition.

(1) Background: To identify the association between the presence or absence of raphe and aortic valve dysfunction as well as the presence of aortopathy in patients with bicuspid aortic valve (BAV); (2) Methods: This retrospective study enrolled 312 participants (mean [SD] age, 52.7 [14.3] years; 227 men [72.8%]) with BAV. The BAVs were divided into those with presence (raphe+) or absence (raphe-) of raphe. Valvular function was classified as normal, aortic regurgitation (AR), or aortic stenosis (AS) using TTE. The pattern of BAV aortopathy was determined by the presence of dilatation at the sinus of Valsalva and the middle ascending aorta using CCT.; (3) Results: BAVs with raphe+ had a higher prevalence of AR (148 [79.5%] vs. 48 [37.8%], P < .001) but a lower prevalence of AS (90 [48.6%] vs. 99 [78.0%], P < .001) compared with those with raphe-. The types of BAV aortopathy were significantly different (P = 0.021) according to those with BAV-raphe+ and BAV-raphe-.; (4) Conclusions: The presence of a raphe was significantly associated with a higher prevalence of AR but a lower prevalence of AS and combined dilatation of the aortic root and middle ascending aorta. The presence of raphe was an independent determinant of AR.

During the high-speed flight of a vehicle in the atmosphere, surface friction with the air generates aerodynamic heating. The aerodynamic heating phenomenon can create extremely high temperatures near the surface. These high temperatures impact material properties and the structure of the aircraft, so thermal deformation measurement is essential in aerospace engineering. This paper revisits high-temperature deformation measurement using the digital image correlation (DIC) technique under high-intensity blackbody radiation with a precise speckle pattern fabrication and a heat haze reduction method. The effect of speckle pattern on the DIC measurement has been thoroughly studied at room temperature, but high-temperature measurement studies have not reported such effects so far. We found that the commonly used methods to reduce the heat haze effect could produce incorrect results. Hence, we propose a new method to mitigate heat haze effects. An infrared radiation heater was employed to make an experimental setup that could heat a specimen up to 950 ℃. First, we mitigated image saturation using a short-wavelength bandpass filter with blue light illumination, a standard procedure for high-temperature DIC deformation measurement. Second, we studied how to determine the proper size of the speckle pattern under a high-temperature environment. Third, we devised a reduction method for the heat haze effect. As proof of the effectiveness of our developed experimental method, we successfully measured the deformation of stainless steel 304 specimens from 25 ℃ to 800 ℃. The results confirmed that this method can be applied to the research and development of thermal protection systems in the aerospace field.

A sintered wick was formed in a heat pipe through the process of sintering a mixture of copper powder with particle sizes of 100㎛ and 200㎛, mixed with a pore-forming agent. On application to the heat pipes. The thermal resistance of heat pipes containing a sintered wick was calculated for different tilting angles (0°, 45°, and 90°) according to the type of powder, thickness of the sintered wick, and the filling ratio of the working fluid. The heat transfer efficiencies were evaluated through temperature tests. The capillary force, which is closely related to heat transfer efficiency, is determined by the effective pore radius resulting from the sintering of the copper powder. Furthermore, it was observed that the heat transfer performance of the heat pipe was at its best when the working fluid filling ratio was 30%. Additionally, the width of the wick was found to have a direct correlation with the heat transfer performance.

The semi-enclosed estuary is very susceptible to changes in the physical and environmental characteristics of the inflow from the land and the coastal sea weather and so the continuous and comprehensive monitoring is necessary for managing the estuary. Nevertheless, the standard procedure or schematic framework has not been proposed appropriately to determine how many instruments are necessary and where they need to be deployed to detect critical changes. Therefore, the present work proposes a systematical strategy for the deployments of the monitoring array by using the combination of the graphical optimization with the objective mapping technique. In order to reflect the spatiotemporal characteristics of the bay, the representative variables and eigenvectors are determined by the Empirical Orthogonal Function (EOF), and the cosine angle among them are calculated for a design index of optimization. At the recommended locations, the sampled representative variables are interpolated to reconstruct their spatiotemporal distribution and compared with the distributions of the true values. Analysis confirms that the selected locations, even with a small number of points, can be used for on-site monitoring. Also, the present framework suggests how to determine installable regions for real-time monitoring stations, which reflect the global and local characteristics of the semi-enclosed estuary.

Micro elastofluidics is a transformative branch of microfluidics, leveraging fluid-structure interaction (FSI) at the microscale to enhance the functionality and efficiency of various microdevices. This review paper elucidates the critical role of advanced computational FSI methods in the field of micro elastofluidics. By focusing on the interplay between fluid mechanics and structural responses, these computational methods facilitate the intricate design and optimisation of microdevices such as microvalves, micropumps, and micromixers, which rely on the precise control of fluidic and structural dynamics. In addition, these computational tools extend to the development of biomedical devices, enabling precise particle manipulation and enhancing therapeutic outcomes in cardiovascular applications. Furthermore, this paper addresses the current challenges in computational FSI and highlights the necessity for further development of tools to tackle complex, time-dependent models under microfluidic environments and varying conditions. Our review highlights the expanding potential of FSI in micro elastofluidics, offering a roadmap for future research and development in this promising area.

Cellular response to mechanical stimuli is a crucial factor for maintaining cell homeostasis. The interaction between extracellular matrix and mechanical stress plays a significant role in organ-izing the cytoskeleton and aligning cells. Tools that apply mechanical forces to cells and tissues, as well as those capable of measuring the mechanical properties of biological cells, have greatly contributed to our understanding of fundamental mechanobiology. These tools have been exten-sively employed to unveil the substantial influence of mechanical cues on the development and progression of various diseases. In this report, we present an economical and high-performance uniaxial cell stretching device. This paper reports the detailed operation concept of the device, ex-perimental design, and characterization. The device was tested with MDA-MB-231 breast cancer cells. Experimental results agree well with previously documented morphological changes re-sulting from stretching forces on cancer cells. Remarkably, our new device demonstrates compa-rable cellular changes within a 30-minute compared to the previous 2-hour stretching duration. Moreover, the device design incorporates an open-source software interface, facilitating conven-ient parameter adjustments such as strain, stretching speed, frequency, and duration. Its versatil-ity enables seamless integration with various optical microscopes, thereby yielding novel insights into the realm of mechanobiology.

The unique properties and morphology of liquid marbles (LMs) make them potentially useful for various applications. Non-edible hydrophobic organic polymer particles are widely used to prepare LMs. It is necessary to increase the variety of LM particles to extend their use into food and pharmaceuticals. Herein, we focus on hydrophobically modified gelatin (HMG) as a base material for the particles. The surface tension of HMG decreased as the length of alkyl chains incorporated into the gelatin and the degree of substitution (DS) of the alkyl chains increased. HMG with a surface tension of less than 37.5 mN/m (determined using equations based on the Young-Dupré equation and Kaelble-Uy theory) successfully formed LMs of water. The minimum surface tension of a liquid in which it was possible to form LMs using HMG particles was approximately 53 mN/m. We also showed that the liquid-over-solid spreading coefficient S_(L/S) is a potential new factor for predicting if particles can form LMs. The HMG particles and the new system for predicting LM formation could expand the use of LMs in food and pharmaceuticals.

We report on an immunofluorescent paper-based assay for the detection of severe acute respiratory symptom coronavirus 2 (SARS-CoV-2) humanized antibody. The paper-based device was fabricated by using lamination technique for easy and optimized handling. Our approach utilises a two-step strategy that involves (i) initial coating of the paper-electrode with recombinant SARS-CoV-2 nucleocapsid antigen to capture the target SARS-CoV-2 specific antibodies, and (ii) subsequent detection of SARS-CoV-2 antibodies using fluorophore-conjugated IgG antibody. The fluorescence readout was observed with fluorescence microscopy. The images were processed and quantified using a MATLAB program. The assay can selectively detect SARS-CoV-2 humanized antibodies spiked in PBS and healthy human serum samples with the relative standard deviation of approximately 6.4% (for n = 3). It has broad dynamic ranges (1 ng to 50 ng/µL in PBS and 5 to 100 ng/µL in human serum samples) for SARS-CoV-2 humanized antibodies with the detection limits of 2 ng/µL (0.025 IU/mL) and 10 ng/µL (0.125 IU/mL) in PBS and human serum samples, respectively. We believe that our assay has the potential to be used as a simple, rapid, and inexpensive paper-based diagnostic device with a portable fluorescent reader to provide point-of-care diagnosis. This assay can be used for rapid examination of a large batch of samples toward clinical screening of SARS-CoV-2 specific antibodies as a confirmed infected active case or to evaluate the immune response to a SARS-CoV-2 vaccine.

1) Background: In service business areas, design enhances the customer experience through the elements which anticipate specific emotional responses of customers. Many service companies are keen to develop and examine design elements from the customer perspective. Furthermore, recently, having considered the significance of customers’ emotional responses by design elements, categorising design elements into manageable dimensions can facilitate the evaluation of design elements. However, design elements and dimensions of design value are not defined in the current service marketing literature, and companies need a measurement tool and managerial guideline to their innovative value creation and compelling service delivery. For these reasons, this research aims to categorise the design value dimensions and propose the managerial implication for the innovative use of design; 2) Methods: This study used the mixed methodology; two stages of interviews and SEM (Structural Equation Modelling); 3) Results: Interview analyses facilitate the identification of design elements in the service delivery process. SEM results underpin the relevance of the categorised design elements and their impact on customer loyalty by comparing different groups (country and time elapsed from experience); and 4) Conclusions: Findings are the fundamentals of developing measuring tool for design and trigger future studies for conceptualising intangible assets.

Rammed earth in a built environment has vapor diffusion characteristics and humidity control ability each of which are respectively attributed to the porous structures and the hydrophilic properties. Indeed, these structures and properties, which allows easily absorbing water parti-cles, hence, affecting the durability of a rammed earth wall. This paper presents the water repel-lency method for rammed earth walls which synthesizes siloxane copolymers containing fluo-rine. The water-repellent properties are investigated by measuring the contact angle, water ab-sorption rate, and compressive strength after spray coating with the synthesized siloxane co-polymers on the surface of the rammed earth specimens under study. The water contact angle of the specimen coated with a siloxane copolymer containing 10 mol.% of a silane monomer with a fluorine group is about 140o. The water absorption of the specimen obtained after immersing in water for 24 hours is low at about 3.5 wt.%. In addition, the compressive strength is remained more than 80% of the corresponding strength of the specimen which is not immersed into water. It is confirmed that the use of a 10% by volume of the siloxane copolymer containing the fluo-rine group may assure the water-repellent performance and the economic competitiveness.

Directed Energy Deposition (DED) is a process that enables high-speed deposition with a sub-millimeter thickness using laser technology. Thus far, defect studies on additive manufacturing, including DED, have focused mostly on preventing pores and crack defects that reduce fatigue strength. On the other hand, evaporation products, fumes and spatters, generated by the high energy have often been neglected despite being some of the main causes of porosity and defects. In high-quality metal deposition, the problems caused by evaporation products are difficult to solve, but they have not yet caught the attention of metallurgists and physicists. This review examines the effect of the laser, material, and process parameters on the evaporation products to help obtain a high-quality metal film layer in thin-DED.

The recycling, incineration, and final disposal rate of municipal solid waste (MSW) are calculated based on the total amount of waste input to each facility in many countries. These statistic data have serious limitation in setting the national goal and policy for effective waste management because it is not considering the amount of foreign objectives in the process of each life-cycle stage. This case study is to estimate the actual rates of recycling, incineration, and final disposal by material flow analysis (MFA) after the collection of MSW in Korea. The actual rates of recycling, incineration and final disposal for MSW in 2016 were 49.9%, 32.9% and 23.1% respectively, indicating that the recycling rate was lower by 10.1%, while the incineration and final disposal rates were raised by 7.6% and 8.4% respectively, compared with the statistics for current MSW. In addition, the changed actual rates of recycling, incineration treatment, and final landfill, and variation of waste treatment charge according to treated amounts per treatment method was analyzed. This results of this study will contribute to establish national level of plan on effective waste management.

Ongoing climate change causes abnormal climate events worldwide such as increasing temperatures and changing rainfall patterns. With South Korea facing growing damage from the increased frequency of localized heavy rains, the country is not an exception. In particular, its steep slope lands, including mountainous areas, are vulnerable to damage from landslides and debris flows. In addition, localized short-term heavy rains that occur in urban areas with extremely high intensity tend to lead a sharp increase in damage from soil-related disasters and cause huge losses of life and property. Currently, South Korea predicts landslides and debris flows using the standards for forecasting landslides and heavy rains. However, as the forecasting is conducted separately for rainfall intensity and accumulated rainfall, this lacks a technique that reflects both amount and intensity of rainfall in an episode of localized heavy rainfall. This study, therefore, aims to develop such a technique by collecting past cases of debris flow occurrences and rainfall events that accompanied debris flows to calculate the rainfall triggering index (RTI) reflecting accumulated rainfall and rainfall intensity. In addition, the RTI is converted into the critical accumulated rainfall (Rc) to use precipitation information and provide real-time forecasting. The study classifies the standards for flow debris forecasting into three levels: ALERT (10%–50%), WARNING (50%–70%), and EMERGENCY (70% or higher), to provide a nomogram for 6 hr, 12 hr, and 24 hr. As a result of applying this classification into the actual cases of Seoul, Chuncheon, and Cheongju, it is found that about 2–4 hr of response time is secured from the point of the Emergency level to the occurrence of debris flows.

Rapid reduction in the $/Wp prices of photovoltaic (solar PV) energy has been proceeded recently, resulting in near exponential deployments with an annual capacity of 200 GW expected by 2020. Achieving high efficiency is necessary for many solar manufacturers to break even. In addition, new innovative installation methods are emerging to complement the improvement of system performance. The floating PV (FPV) solar market space has emerged over the past decade as a method for utilizing the cool ambient environment of the FPV system near the water surface to boost the power output performance of the PV module and ultimately the yield of the PV system. PV module temperature, which is the most critical factor affecting efficiency, ultimately governs the effective performance of solar cells, module, and all semiconductor materials in general. We propose the first ever electrical efficiency equations (${\eta }_{c,FP{V}_1}$ and ${\eta }_{c,FP{V}_2}$) for an FPV module installed on water based on two new predictions of FPV temperature operation models (T_m1 and T_m2), whose coefficients are derived from FPV site data with MATLAB. The theoretical prediction of module temperature shows respective errors of 2% and 4% when compared to the FPVM measured data.

The EULAR Sjögren's Syndrome Disease Activity Index (ESSDAI), EULAR Sjogren’s Syndrome Patient Reported Index (ESSPRI), and other patient-reported outcomes (PROs), such as the visual analog scale (VAS) for symptoms and EULAR sicca score (ESS), are used to assess the disease activity of primary Sjögren’s syndrome (pSS). Recently, Clinical ESSDAI (ClinESSDAI) and Clinical Trials ESSDAI (ClinTrialsESSDAI) were developed for objective clinical disease activity indexes. However, the relationship of ClinESSDAI and ClinTrialsESSDAI with PROs as well as that between ESSPRI and other PROs and the objective parameters of glandular function in pSS have not been established. Herein, we investigated the correlation of ESSPRI and other PROs with the objective parameters of glandular function and the relationship of PROs with ClinESSDAI and ClinTrialsESSDAI in 66 patients with pSS. Correlations were calculated with Spearman’s correlation coefficient. ClinTrialsESSDAI was correlated with ESSPRI, dryness (ESSPRI-Dryness), fatigue, and pain domains of ESSPRI, VAS for oral dryness (oral-VAS), and patient’s global assessment. Although ESSPRI did not correlate with the objective parameters of glandular function, ESSPRI-Dryness, ESS, and oral- and ocular-VAS did. These results suggest that ESSPRI-Dryness, ESS, and VAS for symptoms, but not ESSPRI, reflect the glandular dysfunction and that ClinTrialsESSDAI correlates with PROs for dryness in pSS.

The frame construction of an apartment complex that consists of multiple buildings encounters various uncertainties, owing to the complex relationships among units of work. Currently, the period of such a construction is calculated based on the number of floors of the highest building in the complex. This study quantitatively analyzes an apartment frame construction period using a queue model and evaluates the validity of the estimated period. In this regard, a methodology is proposed for analyzing the construction period by applying the concept of a customer and a server. A case study on the duration of an apartment frame construction is conducted with Korea Land and Housing Corporation, which has supplied the largest number of apartments in South Korea. It was found that the stable state of a queue system was observed when the rate of server utilization was applied to the basement and aboveground floors. However, a stable state was not reached on the ground floor. This study includes non-working days in its calculation and quantitatively analyzes uncertainty factors during construction. Therefore, the findings can be practically utilized to quantitatively plan the durations of work units in an apartment frame construction.

(1) Background: The aim of the present study was to evaluate the effect of ETS homologous factor (EHF) in malignant breast cancer cells. (2) Methods: Overexpression and knockdown of the EHF gene in human and mouse breast cancer cells were performed, and the TCGA dataset and Q-omics were analyzed. (3) Results: We found that the tumor suppressor NDRG2 is correlated with EHF gene expression in triple-negative breast cancer cells, that EHF overexpression results in reduced cell proliferation and that apoptosis is promoted by chemotherapeutic reagent treatment of EHF-overexpressing cells. By EHF overexpression, senescence-associated β-galactosidase activity and p21WAF1/CIP1 expression were increased, suggesting that EHF may induce cellular senescence. In addition, overexpression of EHF reduced the migratory ability and inhibited epithelial-mesenchymal transition (EMT). Furthermore, EHF inhibited the phosphorylation of STAT3. Overexpression of EHF also reduced tumor size, and lung metastasis in vivo. At the tumor site, β-galactosidase activity was increased by EHF. Finally, Kaplan-Meier-plotter analysis showed that TNBC patients with high expression of EHF had a longer relapse-free survival rate. (4) Conclusions: Our findings demonstrated that EHF inhibits breast tumor progression by inducing senescence and regulating EMT in TNBC cells.

Owing to the large ratio of consumption in the building sector, energy saving strategies are required. Energy feedback is an energy-saving strategy that consumers to change their energy-consumption behaviors. The strategy has been principally focused on providing energy-consumption information. However, realization of energy savings using only consumption information remains limited. In this paper, a building-energy three-dimensional (3D) visualization solution is thus proposed. This solution includes the process of diagnosing a building and providing prediction of energy requirements if a building improvement is undertaken. Accurate diagnostic information is provided by real-time measurement data from sensors and building models using a close-range photogrammetry (CRP) method without depending on blueprints. The information is provided by employing visualization effects to increase the energy-feedback efficiency. The proposed strategy is implemented on two testbeds, and building diagnostics are performed accordingly. For the first testbed, the predicted energy improvement amount resulting from the facility upgrade is provided. The second testbed is provided with a 3D visualization of the energy information. The aim is to determine if the building manager will replace the facility after our recommendation is given to improve the building energy efficiency driven from the energy information. Unlike existing systems, which provide only ambiguous data that lack quantitative information, this study is meaningful because it provides energy information with the aid of visualization effects before and after building improvements.

This study aimed to evaluate the positive effect of autumn olive berries (AOB) extract on aging delay by improving the lipid metabolism of middle-aged C. elegans who became obese due to high glucose (GLU) diet. As a result of investigating the total phenol content and DPPH radical scavenging ability of freeze- or spray-dried AOB, freeze-dried AOB showed better antioxidant potential. Afterward, through HPLC analysis, it was confirmed that catechin was the main compound in the polyphenols of AOB. Therefore, we used freeze-dried AOB in subsequent in vivo experiments. AOB inhibited lipid accumulation in both the young adult and middle-aged groups in a concentration-dependent manner under both normal and 2% GLU conditions. Additionally, AOB inhibited ROS accumulation in a concentration-dependent manner under normal and 2% GLU conditions in the middle-aged worms. In particular, AOB also increased the number of body bending and egg production in middle-aged worms. To confirm the intervention of genetic factors related to lipid metabolism in the effect of AOB, body lipid accumulation was confirmed using worms deficient in the daf-16, atgl-1, aak-1, and akt-1. Regarding the effect of AOB on reducing lipid accumulation, the impact was nullified in daf-16 deficient worms under the 2% GLU condition and nullified in both daf-16 and deficient worms under fasting conditions. This means that AOB regulates lipogenesis and lipolysis by mediating daf-16 and atgl-1 in middle-aged worms. Our results suggest that AOB contributes to the aging delay effect by improving lipid metabolism in metabolic impaired middle-aged worms.

Tenascin C (TNC) is an element of the extracellular matrix (ECM) of various tissues, including the skin, and is involved in modulating ECM integrity and cell physiology. Although skin aging is apparently associated with changes in the ECM, little is known about the role of TNC in skin aging. Here we found that Tnc mRNA level was significantly reduced in the skin tissues of aged mice compared with young mice, consistent with reduced TNC protein expression in aged human skin. TNC-large (TNC-L; 330-kDa) and -small (TNC-S; 240-kDa) polypeptides were observed in conditional media from primary dermal fibroblasts. Both recombinant TNC polypeptides, corresponding to TNC-L and TNC-S, increased the expression of type I collagen and reduced the expression of matrix metalloproteinase-1 in fibroblasts. Treatment of fibroblasts with a recombinant TNC polypeptide, corresponding to TNC-L, induced phosphorylation of SMAD2 and SMAD3. TNC increased the level of TGF-β1 mRNA and upregulated the expression of type I collagen by activating the TGF-β signaling pathway. In addition, TNC also promoted the expression of type I collagen in fibroblasts embedded in a three-dimensional collagen matrix. Our findings suggest that TNC contributes to the integrity of ECM in young skin and to prevention of skin aging.

It is crucial to forecast the water demand accurately for supplying water efficiently and stably in a water supply system. In particular, accurately forecasting short-term water demand helps in saving energy and reducing operating costs. With the introduction of the Smart Water Grid (SWG) in a water supply system, the amount of water consumption is obtained in real time through an advanced metering infrastructure (AMI) sensor, which can be used for forecasting the short-term water demand. The models widely used for water demand forecasting include the autoregressive integrated moving average, radial basis function-artificial neural network, quantitative multi-model predictor plus, and long short-term memory. However, there is a lack of research on assessing the performance of models and forecasting the short-term water demand by applying the data on the amount of water consumption by purpose and the pipe diameter of an end-use level of the SWG demonstration plant in each demand forecasting model. Therefore, in this study, the short-term water demand was forecasted for each model using the data collected from the AMI, and the performance of each model was assessed. The Smart Water Grid Research Group installed ultrasonic-wave-type AMI sensors in the block 112 located in YeongJong Island, Incheon, and the actual data used for operating the SWG demonstration plant were adopted. The performance of the model was assessed by using the residual, root mean square error (RMSE), normalized root mean square error (NRMSE), Nash–Sutcliffe efficiency (NSE), and Pearson correlation coefficient (PCC) as indices. The water demand forecast was slightly underestimated in models that employed the assessment results based on the RMSE and NRMSE. Furthermore, the forecasting accuracy was low for the NSE due to a large number of negative values; the correlation between the observed and forecasted values of the PCC was not high, and it was difficult to forecast the peak amount of water consumption. Therefore, as the short-term water demand forecasting models using only time and the amount of water consumption have limitations in reflecting the characteristics of consumers, a water supply system can be managed more precisely if other factors (weather, customer behavior, etc.) influencing the water demand are applied.

Soybean is a highly nutritious legume grown globally as a food and feed crop. An examination of a collection of 10 cultivated and 6 wild Korean soybean varieties showed that there is phenotypic variability notable in different soybeans. Therefore, to develop a list of biomarker candidates useful for growing soybeans of better quality and quantity, the genes of 16 Korean soybean varieties were compared with those of the reference Glycine max var. Williams 82. The comparison was made through gene sequencing to facilitate selection of nsSNPs. The objective of the study was to find out the structural and functional variations caused by nsSNPs and discuss whether the collection of Korean soybean varieties qualifies as biomarkers based on their phenotypic traits. Analysis of the data collected was done using four software: SIFT, Polyphen, PANTHER, and I-mutant 2.0, which are designed to detect the rate of functional and structural variations caused by the nsSNPs in cultivated and wild soybean varieties. Genotypic information obtained in the analysis was used to develop a core collection of biomarkers based on whether nsSNP content was found in more than half of the 16 samples. Therefore, the list of biomarker candidates developed from this study showed that Korean soybean could provide valuable information needed in both future crop genetic research and identification of biomarkers.

The VisionCube is a 2-unit CubeSat developed in-house, of which the primary mission is aimed at detecting the occurrence of transient luminous events in the upper atmosphere and obtaining corresponding images from the low Earth orbit. An on-board TLE observation system of the VisionCube cubesat is designed and developed by incorporating a photon-sensitive MaPMT and a CMOS image sensor. Also, a distinctive TLE observation software which enables detecting the TLEs and capturing images in a timely manner is devised. By taking into account the limited resources of a small CubeSat in size and power, the on-board observation system is developed employing a system-on-chip design architecture by which both hardware and software can be integrated seamlessly. The purpose of this study is to investigate the functionality of the hardware and the validity of the software algorithm to show the on-board system will operate properly with no human intervention during the space operation. To this end, a ground simulation facility is constructed to emulate the space environment of the TLE occurrence using a set of UV LEDs inside a darkbox. Based on the analysis of the spectral and temporal properties of the TLEs, the randomly generated UV LED pulses are opted for verification scenarios for the TLE observation system. The validation results show that the hardware and the software algorithm of the on-board observation system can effectively detect the TLEs and obtain the images during the on-orbit operation.

The effect of the acetylene and hydrogen gases mixture ratios in direct low-temperature vacuum carburization was investigated. The gas ratio is an important parameter for producing the free radicals in the carburization. The free radicals can remove the natural oxide film by the strong reaction of the hydrocarbons, and then thermodynamically activity can be increased. When the gas ratio was below 1, the supersaturation expanded austenite layers were formed on the surface of the AISI 316L stainless steel, which had the maximum carbon solubility up to 11.5 at.% at 743 K, were formed. On the other hand, when the gas ratio was above 1, the carbon concentration of them remained low even if the process time was enough increased to reach the maximum carbon solubility. As a result, the carbon concentration underneath the surface was determined to be highly dependent on the gas mixture ratio of acetylene and hydrogen. In conclusion, it is necessary to restrict the ratio of acetylene and hydrogen gases to total mixture gases to form the expanded austenite layer with the high carbon concentration in the direct low-temperature vacuum carburization.

Bone growth plate abnormalities and skull shape defects are seen in hypophosphatasia, a heritable disorder in humans that occurs due to deficiency of Tissue Nonspecific Alkaline Phosphatase (TNAP, Alpl) enzyme activity. Abnormal development of the cranial base growth plates (synchondroses) and abnormal skull shapes have also been demonstrated in global TNAP-/- mice. To distinguish local vs. systemic effects of TNAP on skull development, we utilized P0-Cre to knockout TNAP only in cranial neural crest derived tissues using TNAP flox mice. Here we show that TNAP deficiency in cranial neural crest leads to leads to skull shape defects and deficient growth of the intersphenoid synchondrosis (ISS). ISS chondrocyte abnormalities included increased proliferation in resting and proliferative zones with decreased apoptosis in hypertrophic zones. ColX expression is increased, indicative of premature differentiation in the absence of TNAP. Sox9 expression is increased in both resting and prehypertrophic zones of mutant mice. Expression of PTHrP and IHH were also increased. Finally, cranial base organ culture revealed that inorganic phosphate (Pi) and pyrophosphate (PPi) have specific effects on cell signaling and phenotype changes in the ISS. Together, these results demonstrate that TNAP expression in growth plate chondrocytes is essential for normal development, and that the mechanism likely involves Sox9, PTHrP, IHH and PPi.

The antioxidant and anti-inflammatory abilities of beeswax alcohol (BWA) are well reported in animal and human clinical studies, with a significant decrease in malondialdehyde (MDA) in blood, reduction of liver steatosis, and decrease in insulin. On the other hand, there is insufficient information to explain the in vitro antioxidant activity of BWA because it is extremely insoluble in aqueous buffer system. The BWA mixture was incorporated into reconstituted HDL (rHDL) with apoA-I, and the physiological functions of BWA in a water system were evaluated. After synthesis of rHDL with palmitoyloleoyl phosphatidylcholine (POPC), cholesterol, apolipoprotein A-I (apoA-I), and the BWA at molar ratios of 95:5:1:0 (rHDL-0), 95:5:1:0.5 (rHDL-0.5), and 95:5:1:1 (rHDL-1) for POPC:FC:apoA-I:BWA, the particle size of rHDL-1 was increased 15% compared to rHDL-0. rHDL-1 exhibited the strongest anti-glycation activity, up to 18% less glycation than rHDL-0 treated HDL3, with the highest protection of apoA-I from proteolytic degradation: a 28% larger band intensity than that of rHDL-0 treated HDL3 in the presence of fructose (final 250 mM). The antioxidant ability to inhibit cupric ion-mediated LDL oxidation increased as the BWA content in rHDL increased. The rHDL-1-treated LDL exhibited the smallest oxidation extent in electromobility with the least quantification of oxidized species (MDA). The antioxidant activities of HDL, ferric ion reduction ability (FRA), and paraoxonase (PON) were enhanced by the BWA in rHDL treatment with a concomitant increase in the molar ratio. rHDL-1-treated HDL showed 20–22% higher FRA and PON activities than rHDL-0-treated HDL. A microinjection of each rHDL into zebrafish embryos was performed in the presence of carboxymethyllysine (CML). The rHDL-1 injected embryo exhibited the highest survivability (~63%), whereas the CML alone group showed 28% survivability. A higher BWA content in rHDL helped neutralize the CML toxicity, resulting in higher survivability and normal developmental morphology. In contrast, the CML alone injected embryo showed severe retardation of the developmental speed and morphological defect. The CML-alone group showed the highest extent of reactive oxygen species (ROS) production and cellular apoptosis in embryos, but a co-injection of rHDL-1 resulted in a remarkable decrease in ROS and apoptosis. The dermal application of rHDL containing BWA resulted in higher potent wound-healing activity in a dose-dependent manner with decreased reactive oxygen species and cellular apoptosis in the cutaneous wound area in the presence of CML. Conclusively, incorporating BWA in rHDL significantly enhanced the anti-glycation and antioxidant activities in rHDL via more stabilization of apoA-I with a larger particle size. The rHDL containing BWA facilitated enforced inherent antioxidant ability of HDL and anti-inflammatory activity to suppress the CML toxicities in zebrafish embryos and to ameliorate CML-aggravated chronic wounds in adult zebrafish.

Congenital anomalies of the kidney and urinary tract (CAKUT) are common birth defects deriving from abnormalities in renal differentiation during embryogenesis. CAKUT is the major cause of end-stage renal disease and chronic kidney diseases in children, but its genetic causes remain largely unresolved. Here we discuss advances in the understanding of how MAPK/ERK activity contributes to the regulation of ureteric bud branching morphogenesis, which dictates the final size, shape, and nephron number of the kidney. Recent studies also demonstrate that MAPK/ERK pathway is directly involved in nephrogenesis, regulating both the maintenance and differentiation of the nephrogenic mesenchyme. Interestingly, aberrant MAPK/ERK signaling is linked to many cancers, and recent studies suggest it also plays a role in the most common pediatric renal cancer, Wilms’ tumor.

Cervical cancer, primarily caused by high-risk human papillomavirus (HR-HPV) types 16 and 18, is a major global health concern. Persistent HR-HPV infection can progress from reversible pre-cancerous lesions to invasive cervical cancer, which is driven by the oncogenic activity of human papillomavirus (HPV) genes, particularly E6 and E7. Traditional screening methods, including cytology and HPV testing, have limited sensitivity and specificity. This review explores the ap-plication of p16/Ki-67 dual-staining cytology for cervical cancer screening. This advanced im-munocytochemical method allows for simultaneously detecting p16 and Ki-67 proteins within cervical epithelial cells, offering a more specific approach for triaging HPV-positive women. Dual staining and traditional methods are compared, demonstrating their high sensitivity and negative predictive value but low specificity. The increased sensitivity of dual staining results in higher detection rates of CIN2+ lesions, which is crucial for preventing cervical cancer progression. However, its low specificity may lead to increased false-positive results and unnecessary biopsies. The implications of integrating dual staining into contemporary screening strategies, particularly considering the evolving landscape of HPV vaccination and changes in HPV genotype prevalence are also discussed. New guidelines and further research are necessary to elucidate the long-term effects of integrating dual staining into screening protocols.

Background: Accurate diagnosis of the differentially aggressive fungus Leptosphaeria maculans and Leptosphaeria biglobosa causing Blackleg in crucifers is crucial. Available markers were designed decades ago which may become ineffective due to the ever evolving nature of the fungus, requiring the development of more precise molecular markers. Methods: The whole genomes of available isolates belonging to this two species were aligned using progressive MAUVE tool, species specific genomic regions were extracted and species specific primers were designed from the sequences that encode for effector proteins. Results: Three (Lm1, Lm2 and Lm5) and two (Lb3 and Lb3’) primer sets specifically detected the isolates of target species in PCR based assay, of which the primers Lm5 and Lb3’ were multiplexed for detection of Leptosphaeria maculans and Leptosphaeria biglobosa, generating PCR amplicons of 230 and 834 bp, respectively from a single PCR reaction. The markers were highly sensitive and were able to amplify target species from crude ‘pseudothecia and ascospores suspension’ without requiring DNA extraction. Conclusions: These markers, solitarily or in combination, designed from species specific genomic segments will serve as precise, sensitive and rapid detection of Leptosphaeria maculans and Leptosphaeria biglobosa species and will be helpful for surveillance, management and transboundary quarantine of the devastating disease.

Core-shell particles are heterogenous micro- or nanoparticles with solid, liquid or gas core encapsulated by a protective solid shell. The unique composition of core and shell materials imparts smart properties to the particles. Core-shell particles are gaining increasing attention as tuneable and versatile carriers for pharmaceutical and biomedical applications including targeted drug delivery, controlled drug release, and biosensing. This review first provides an overview of fabrication methods for core-shell particles, followed by a brief discussion on their application and a detailed analysis on manipulation including assembly, sorting, and triggered release. We compile current methodologies employed for manipulation of core-shell particles and demonstrate how existing methods of assembly and sorting micro/nanospheres can be adopted or modified for core-shell particles. Various triggered release approaches for diagnostics and drug delivery are also discussed in detail.

Separation and detection of cells and particles in a suspension are essential for various applications, including biomedical investigations and clinical diagnostics. Microfluidics realizes the miniaturization of analytical devices by controlling the motion of a small volume of fluids in microchannels and microchambers. Accordingly, microfluidic devices have been widely used in particle/ cell manipulation processes. Different microfluidic methods for particle separation include dielectrophoretic, magnetic, optical, acoustic, hydrodynamic, and chemical techniques. Dielectrophoresis (DEP) is a method for manipulating polarizable particles’ trajectories in non-uniform electric fields using unique dielectric characteristics. It provides several advantages for dealing with neutral bioparticles owing to its sensitivity, selectivity, and noninvasive nature. This review provides a detailed study on the signal-based DEP methods that use the applied signal parameters, including frequency, amplitude, phase, and shape for cell/particle separation and manipulation. Rather than employing complex channels or time-consuming fabrication procedures, these methods realize sorting and detecting the cells/particles by modifying the signal parameters while using a simple device. In addition, these methods can significantly impact clinical diagnostics by making low-cost and rapid separation possible.

Optical wireless communication is a promising emerging technology that addresses the limitations of radio-frequency-based wireless technologies. This study presents a novel hybrid modulation for optical camera communication (OCC); it integrates two waveforms transmitted from a single transmitter light-emitting diode (LED) and received by two rolling-shutter camera devices. Then, a smart camera with a high-resolution image sensor captures the high-frequency signal, and a low-resolution image sensor from a smartphone camera captures the low-frequency signal. Through this hybrid scheme, two data streams are transmitted from a single LED lamp; this reduces the cost of the indoor OCC device compared to one that transmits two signals from two different LEDs. In proposed scheme, rolling-shutter orthogonal frequency-division multiplexing is used for the high-frequency signals, and M-ary frequency-shift keying is used for the low-frequency signals in the time domain. This proposed scheme is compatible with smart phone camera and USB camera. By controlling the OCC parameters, the hybrid scheme can be implemented with high performance for a communication distance of 10 m.

Decapod assemblages in Zostera marina beds from two bays adjacent to unvegetated habitats were investigated to assess their influence on decapod assemblages. Thirty-eight decapod species belonging to 4 taxa were collected using a small beam trawl at four habitat types from two different locations off the coast of Namhae Island, southern Korea. Dominant decapod taxon at all habitats was the caridean shrimps, with Eualus leptognathus, Heptacarpus pandaloides, Latreutes anoplonyx, La. laminirostris and Palaemon macrodactylus being the most abundant caridean species. Crabs were characterized by the highest biomass, but moderate species richness and abundance. Penaeoids and sergestoids shrimps only accounted for <1% of the total decapod abundance. The number of species, their abundance, and the diversity of decapod assemblages varied greatly by habitat type, season, and diel patterns. Species number and abundance peaked in seagrass beds of southern exposed bays during the autumn, and were lowest in unvegetated habitats during the summer months. Diel decapod species and catch rates were higher at night. Dense seagrass vegetation and nighttime supported greater decapod species richness and higher mean densities, but not diversity. Multivariate analyses revealed that habitat type and season significantly affected the structure of decapod assemblages, but diel patterns had a minor influence. Among decapod species, Pa. macrodactylus and Pugettia quadridens characterized the decapod assemblages in seagrass beds at the northern semi-closed bay, while Telmessus acutidens, Crangon affinis, Cr. hakodatei, Charybdis japonica and Portunus sanguinolentus were significantly associated with both vegetated and unvegetated habitats at the southern exposed bay, with the former two species more abundant during winter and spring.

The human degenerative cartilage has low regenerative potential. Chondrocyte transplantation offers a promising strategy for cartilage treatment and regeneration. Currently chondrogenesis using human pluripotent stem cells are accomplished using human recombinant growth factors. Here, we differentiated human induced pluripotent stem cells (hiPSCs) into chondrocytes and cartilage pellet using minicircle vectors. Minicircles are used as a non-viral gene delivery system for gene therapy in various diseases. Non-viral gene delivery can produce growth factors without integrating into the host genome. Minicircle vectors containing bone morphogenetic protein 2 (BMP2) and transforming growth factor, beta 3 (TGFβ3) were successfully generated and delivered to hiPSC-derived outgrowth (OG) cells. Cell pellets generated using minicircle-transfected OG cells successfully differentiated into chondrogenic lineage. Chondrogenic pellets transfected with growth factor-encoding minicircles effectively recovered osteochondral defect in rat models. Taken together, this work shows the potential application of minicircles in cartilage regeneration using hiPSCs.

The upregulated expression of thyrosine kinase AXL has been reported in several hematologic and solid human tumors including gastric, breast, colorectal, prostate, and ovarian cancers. Thus, AXL can potentially serve as a diagnostic and prognostic biomarker for various cancers. This paper reports the first-ever use of loop-mediated isothermal amplification (LAMP) of the AXL gene as a diagnostic method for ovarian cancer. We demonstrated simple instrumentation toward a point-of-care device to perform LAMP. This paper also reports the first-ever use of core-shell beads as a microreactor to perform LAMP as an attempt to promote environmentally friendly laboratory practices.

Cellular response to mechanical stimuli is an integral part of cell homeostasis. The interaction of the extracellular matrix with the mechanical stress plays an important role in cytoskeleton organisation and cell alignment. Insights from the response can be utilised to develop cell culture methods that achieve predefined cell patterns, which are critical for tissue remodelling and cell therapy. We report the working principle, design, simulation and characterisation of a novel electromagnetic cell stretching platform based on the double-sided axial stretching approach. The device is capable of introducing a cyclic and static strain pattern on a cell culture. The platform was tested with fibroblasts. The experimental results are consistent with the previously reported cytoskeleton reorganisation and cell reorientation induced by strain. The orientation of the cells is highly influenced by external mechanical cues. Cells reorganise their cytoskeleton to avoid external strain and to maintain intact extracellular matrix arrangements.

Substrate binding proteins (SBP) bind to specific ligands in the periplasmic region and bind to membrane proteins to participate in transport or signal transduction. Typical SBPs consist of two α/β domains and recognize the substrate by hinge motion between two domains. Conversely, short length Rhodothermus marinus SBP (named as RmSBP) exists around the methyl-accepting chemotaxis protein. We previously determined the crystal structure of RmSBP consisting of a single α/β domain, but the substrate recognition mechanism is still unclear. To better understand the short length RmSBP, we performed comparative structure analysis, computational substrate docking, and X-ray crystallographic study. RmSBP shares a high level of similarity in α/β domain with other SBP proteins, but it has a distinct topology in the C-term region. The substrate binding model suggested that conformational change in the peripheral region of RmSBP was required to recognize the substrate. We determined the crystal structures of RmSBP at pH 5.5, 6.0, and 7.5. RmSBP showed structural flexibility of the β1-α2 loop, β5-β6 loop, and extended C-term domain based on the electron density map and temperature B-factor analysis. These results provide information that will further the understanding of the function of the short length SBP.

(1) Background: Ferric carboxymaltose (FCM) is an intravenous (IV) high-dose iron that is effective in the treatment of iron deficiency anemia. This study was to determine if preoperative IV FCM administration could improve recovery from postoperative anemia in patients undergoing revision total joint arthroplasty. (2) Methods: This prospective randomized controlled study analyzed 82 patients undergoing revision total joint arthroplasty during a single hospitalization. Patients in the iron group (n = 41) were administered 1000 mg of IV FCM two weeks preoperatively, while those in the control group (n = 41) were not. Moreover, patients with anemia defined as a preoperative suboptimal Hb concentration &lt;13.0 g/dl were compared according to IV FCM administration. The absolute Hb levels and changes in Hb levels, iron profiles, transfusion rate, and EuroQOL 5-dimension (EQ-5D) scores were compared. (3) Results: There were no significant differences in recovery of Hb levels at each timepoint between the two groups; however, the changes in Hb levels from baseline to four weeks postoperatively showed marginally significant differences favoring the iron group (p = 0.052). However, for preoperatively anemic patients, the change in hemoglobin (Hb) levels between baseline and four weeks postoperatively was significantly better in the iron group than in the control group (iron group [n = 26], −0.3 ± 0.7 g/dL vs. control group [n = 27], −0.9 ± 0.8 g/dL; p = 0.040), although the absolute Hb levels, transfusion rates, and patient quality of life were comparable (all p &gt; 0.05). The iron group showed improved iron metabolite levels including serum ferritin and transferrin saturation four weeks postoperatively, and no adverse events associated with IV FCM administration occurred in either group. (4) Conclusions: Preoperative IV FCM in anemic individuals undergoing revision joint arthroplasty was effective in accelerating recovery from surgery-related anemia by improving Hb levels without any adverse events, despite similar actual Hb levels between the groups. Our findings are clinically relevant and can facilitate determination of the suitability of IV FCM as a safe and reliable protocol for iron supplementation for anemia correction.

A special vibration damper is proposed for material property identification through a scratching process on a vibrating object. This paper presents the design and working principle of a scratching damper based on a scratch test device. A non-contact electromagnetic shaker is used to generate the shaking force for the vibration of the tested object. The required pressure on the scratched material during the scratching process is generated by a compression spring and adjusted by changing the amount of compression of the spring. The proposed damper is designed and tested on extruded aluminum samples for the determination of its Young’s modulus and hardness and validated by using the standard test instruments. Observations of physical dimensions of the scratching tracks are determined by microscope and were utilized to compute the scratching energy factor. Load curves are obtained at different pressure of the scratching process. The hysteresis loop energy during the scratching process of the tested object is measured and used for the determination of material properties of the object. Furthermore, energy conservation law, scratch energy release rate and loop energy release rate are used to determine the Young’s modulus and hardness of the sample. The measurement accuracy of the modulus and hardness of the tested sample is evaluated. The proposed method of material testing has several advantages over the traditional methods such as low cost and high repeatability, and may be used as an alternative to the standard modulus and hardness testers.

The current study investigated the use of two-dimensional spatial distribution mapping representing the chlorophyll-a level in a river generated via an unmanned aerial vehicle (UAV) and an unmanned surface vehicle (USV). A domestically developed UAV (Remo-M, Uconsystem Inc., Korea) and a USV developed by our research team were used to collect data from the Nae Seong stream in Korea. An adaptation of the “Data Cleaner” tool was developed and used for USV data processing and analysis. The operation of the autonomous USV was successful. Four previously described indices for quantifying algal blooms in rivers were utilized to create chlorophyll-a images, the normalized difference vegetation index (NDVI), the normalized green red difference index, the green normalized difference vegetation index (GNDVI), and the normalized difference red edge index. The suitability of the linear regression analysis of the correlation between the spectral indices obtained using the UAV and the in situ chlorophyll-a data obtained using the USV was evaluated with the coefficient of determination (R2) at a significance level of p &lt; 0.001. In field application and correlational analysis the NDVI was strongly correlated with chlorophyll-a (R2 = 0.88, p < 0.001), and the GNDVI was moderately correlated with chlorophyll-a (R2 = 0.74, p < 0.001). The map of chlorophyll-a was successfully quantified using the UAV and USV hybrid platforms.

Cancer, a globally prevalent and often deadly disease, holds promise for improved treatment through the integration of innovative medical technologies and interdisciplinary collaborations. Despite advancements, current cancer therapies lack a specific focus on addressing recurrence and targeting cancer stem cells (CSCs), known contributors to relapse. In this study, we utilized three types of cancer cells and generated three types of CSCs derived from them to conduct proteomic analysis and identified shared cell surface biomarkers as potential targets for a comprehensive treatment strategy. The selected biomarkers underwent evaluation through shRNA treatment, revealing contrasting functions in cancer and CSCs. Knocking down the identified protein showed promising results in regulating epithelial-mesenchymal transition (EMT) and stemness via the ERK signaling pathway. This led to a reduction in resistance to anticancer agents, ultimately enhancing the overall anticancer effects. Additionally, the biomarker's significance in clinical patient outcomes was confirmed using bioinformatics. Our study suggests a novel cancer treatment strategy that addresses existing limitations in current anticancer therapies.

Present-day lifestyle associated with high calorie-fat intake and accumulation, as well as energy imbalance, has led to the development of obesity and its comorbidities, which have emerged as some of the major health issues globally. To combat the disease, many studies have reported the anti-obesity effects of natural compounds in foods, with some advantages over chemical treatments. Carotenoids, particularly xanthophyll derived from seaweeds, have attracted the attention of researchers due to their notable biological activities, which are associated mainly with their antioxidant properties. Their involvement in oxidative stress modulation, regulation of major transcription factors and enzymes as well as their antagonistic effects on various obesity parameters have been examined in both in-vitro and in-vivo studies. The present review is a collation of published research over the last decade on the anti-oxidant properties of seaweed xanthophyll carotenoids, with a focus on fucoxanthin and astaxanthin and their mechanisms of action in obesity prevention and treatment.