Keywords: Wall-like RC columns; Strengthening; FRP; NSM rebars; Steel plates; Testing; FE modeling; Preloading.

Self-driving vehicles demand efficient and reliable depth sensing technologies. Lidar, with its capacity for long-distance, high-precision measurement, is a crucial component in this pursuit. However, conventional mechanical scanning implementations suffer from reliability, cost, and frame rate limitations. Solid-state lidar solutions have emerged as a promising alternative, but the vast amount of photon data processed and stored using conventional direct time-of-flight (dToF) prevents long-distance sensing unless power-intensive partial histogram approaches are used. In this paper, we introduce a groundbreaking ‘guided’ dToF approach, harnessing external guidance from other onboard sensors to narrow down the depth search space for a power and data-efficient solution. This approach centers around a dToF sensor in-which the exposed time widow of independent pixels can be dynamically adjusted. We utilize a 64-by-32 macropixel dToF sensor and a pair of vision cameras to provide the guiding depth estimates. Our demonstrator captures a dynamic outdoor scene at 3 fps with distances up 75 m. Compared to a conventional full histogram approach, on-chip data is reduced by over 25 times, while the total laser cycles in each frame are reduced by at least 6 times compared to any partial histogram approach. The capability of guided dToF to mitigate multipath reflections is also demonstrated. For self-driving vehicles where a wealth of sensor data is already available, guided dToF opens new possibilities for efficient solid-state lidar.

Necrotizing pneumonia due to Methicillin-Resistant Staphylococcus Aureus (MRSA) is devastating and difficult to treat in preterm infants. We report a case of severe MRSA necrotizing pneumonia in a preterm infant. As an add-on rescue therapy to vancomycin, linezolid rapidly cured this case after the failure of vancomycin plus rifampicin. This rapid cure suggests that adjunctive rather than rescue linezolid may be considered in such cases.

Background. The aim of this study is to examine whether biomarkers of the immune-inflammatory response (IRS) and endogenous opioid (EOS) systems are associated with affective symptoms in schizophrenia. Methods. We recruited 115 schizophrenia patients and 43 healthy controls and assessed the Hamilton Depression (HDRS) and Anxiety (HAM-A) rating Scale scores as well as serum levels of interleukin (IL)-6, IL-10, eotaxin (CCL11), high mobility group box 1 (HMGB1), Dickkopf-related protein 1 (DKK1), and mu (MOR) and kappa (KOR) opioid receptors.Results. The HDRS and HAM-A scores are significantly and positively correlated with a) psychosis, hostility, excitation, mannerism, negative symptoms, psychomotor retardation, and formal thought disorders; and b) lowered scores on semantic and episodic memory, executive functions, and attention tests as measured with the Brief Assessment of Cognition in Psychiatry. Both HDRS and HAM-A are significantly increased in non-responders to treatment as compared with partial responders. Both affective scores are strongly associated with latent vectors extracted from all symptoms, reflecting overall severity of psychosis (OSOS), and neurocognitive test scores, reflecting a generalized cognitive decline (G-CoDe). The HDRS score was strongly and positively associated with IL-6, HMGB1, KOR, and MOR levels, and the HAM-A score with IL-6, IL-10, CCL11, HMGB1, KOR, and MOR levels. A single latent trait may be extracted from OSOS, G-CoDe, and the HDRS and HAMA scores, and this latent vector score is strongly predicted by HMGB1, MOR, and DKK1.Conclusion. Immune-inflammatory and EOS pathways contribute to the phenome of schizophrenia, which comprises OSOS, affective, and physiosomatic symptoms, and G-CoDe.

This article's goal is to investigate the structural model that explains how awareness of consequences, subjective norms, attitude and behavior control variables influence plastic wastes behavioral intention in Jeddah's beaches, Saudi Arabia. A quantitative approach was employed. For data analysis, structural equation modeling was used. Based on the literature analysis, the study used a structured questionnaire. Multiple statistical analyses were used to examine the hypotheses. This study conducts a survey on a sample of 390 local tourists to investigate their intention to reduce plastic wastes. To increase the explaining power for behavioral intention, this study extended the TPB by adding awareness of consequences. The study's participants were selected randomly. 340 of them agreed and answered the questionnaire, yielding a percentage response rate 87%. This produced 271 valid questionnaires for data analysis after closely examining the survey. The results demonstrate a positive influence of subjective norms, perceived behavioral control, and consequences awareness on environmental behavioral intention. On the other hand, attitude does not significantly contribute to predict EBI. Governments, legislators, and researchers may use the work's findings to create and execute efficient waste management programs.

Background: The biofilm-forming bacteria Porphyromonas gingivalis (P. gingivalis) is primarily responsible for periodontal disorders, which continue to be a global health issue. Despite the widespread use of antibiotics like metronidazole, other potent therapeutic a crucial quorum sensing molecule implicated in the formation of P. gingivalis biofilm. Approaches are now being explored due to the growing challenge of antibiotic resistance. Objective: In particular, chemicals from Symphytum Officinale (S) and Panax Ginseng (G) plants will be examined in this study to assess if they have the ability to inhibit biofilm and to prevent the development of acylated homoserine lactones (AHLs), a quorum sensing molecule. Materials and Methods: With Metronidazole serving as a control, the antibacterial effects of these substances (Symphytum Officinale and Panax Ginseng) were examined against a standard strain and a clinical isolate of P. gingivalis. Dilutions of these plant extracts were used either alone (G+S) or in conjunction with metronidazole (G+S+F), to assess their antibacterial activity using antibacterial susceptibility test (inhibition zone), biofilm inhibition and disruption assay (optical density) and quorum sensing inhibition assay (AHL). Results: The combinations of Symphytum officinale, Panax Ginseng and metronidazole (S+G+F) showed the maximum effectiveness with highest zone of inhibition (25.000±0.001 mm) and biofilm inhibition (98.46%), and were comparable to G+S (inhibition zone of 24.341±0.593 mm and biofilm inhibition of 97.76%), and significantly different in the degree of biofilm inhibition with different treatment scenarios. Additionally, the plant's extracts and combinations are specific concentrations had a significant effect on the suppression of the generation of AHL (p < 0.05). Conclusion: According to preliminary research, these plant-derived substances, especially when paired with metronidazole, significantly inhibited the growth of P. gingivalis biofilm providing valuable information for the development of innovative therapeutic approaches for periodontitis and other biofilm-associated illnesses.

Schizophrenia comprises various symptom domains, including positive and negative symptoms. Machine learning showed that a) negative symptoms are significantly interrelated with PHEM (psychosis, hostility, excitation, and mannerism) symptoms, formal thought disorders (FTD) and psychomotor retardation (PMR); and b) stable phase schizophrenia comprises two distinct classes, namely Major Neuro-Cognitive Psychosis (MNP, largely overlapping with deficit schizophrenia) and Simple NP (SNP). In this study, we recruited 120 MNP patients and 54 healthy subjects and measured the above-mentioned symptom domains. In MNP, there were significant associations between negative and PHEM symptoms, FTD and PMR. A single latent trait, which is essentially unidimensional, underlies these key domains of schizophrenia and MNP and additionally shows excellent internal consistency reliability, convergent validity, and predictive relevance. Confirmatory Tedrad Analysis indicates that this latent vector fits a reflective model. The lack of discriminant validity shows that PHEM and negative symptoms greatly overlap and probably measure the same construct. Soft Independent Modeling of Class Analogy (SIMCA) shows that MNP (diagnosis based on negative symptoms) is better modeled using PHEM symptoms, FTD, and PMR than negative symptoms. In conclusion, in stable phase MNP, a restricted sample of the schizophrenia population, negative and PHEM symptoms, FTD and PMR belong to one underlying latent vector reflecting overall severity of schizophrenia (OSOS). The bi-dimensional concept of “positive” and “negative” symptoms cannot be validated and, therefore, future research in stable phase schizophrenia should consider that the latent phenomenon OSOS as well as its 8 reflective manifestations are the key factors of schizophrenia phenomenology.

This paper introduces the complex Rayleigh-van der Pol-Duffing oscillators (RVDOs), which are hyperchaotic and can be either autonomous or non-autonomous. The fundamental dynamics of the autonomous and nonautonomous complex RVDOs including dissipation, symmetry, fixed points and their stability are studied. These oscillators are found in various important fields of physics and engineering. The paper proposes a scheme to achieve phase synchronization (PS) and antiphase synchronization (APS) for different dimensional models. These kinds of synchronization are considered as generalization of several other types of synchronization. For this scheme we use the active control method based on Lyapunov stability theory. By analytically determining the control functions, the scheme achieved PS and APS. Our scheme is applied to study PS of hyperchaotic behaviours for two distinct hyperchaotic non-autonomous and autonomous complex RVDOs. Additionally, the scheme is employed to achieve APS of chaotic real non-autonomous RVDO and hyperchaotic complex autonomous RVDO, including those with different dimensions. Our work presents numerical results that plot the amplitudes and phases of these hyperchaotic behaviours, demonstrating the successful achievement of PS and APS.

In Schizophrenia, pathway-genotypes may be constructed by combining interrelated immune biomarkers with changes in specific neurocognitive functions that represent aberrations in brain neuronal circuits. These constructs provide insight on the phenome of schizophrenia and show how pathway-phenotypes mediate the effects of genome X environmentome interactions on the symptomatology/phenomenology of schizophrenia. Nevertheless, there is a lack of knowledge how to construct pathway-phenotypes using Partial Least Squares (PLS) path modeling and Soft Independent Modeling of Class Analogy (SIMCA). This paper aims to provide a step-by-step utilization guide for the construction of pathway-phenotypes that reflect aberrations in the neuroimmune - brain circuit axis (NIBCA) in deficit schizophrenia. This NIBCA index is constructed using immune biomarkers (CCL-2, CCL-11, IL-1β, sIL-1RA, TNF-α, sTNFR1, sTNFR2) and neurocognitive tests (Brief Assessment of Cognition in Schizophrenia) predicting overall severity of schizophrenia (OSOS) in 120 deficit SCZ and 54 healthy participants. Using SmartPLS path analysis, a latent vector is extracted from those biomarkers and cognitive tests, which shows a good construct reliability (Cronbach alpha and composite reliability) and replicability and which is reflectively measured through its NIBCA manifestations. This NIBCA pathway-phenotype explains 75.0% of the variance in PHEMN (psychotic, hostility, excitation, mannerism and negative) symptoms. Using SIMCA, we constructed a NIBCA pathway-class that defines deficit schizophrenia as a qualitatively distinct nosological entity and which allows patients with deficit schizophrenia to be authenticated as belonging to the deficit schizophrenia class. In conclusion, our nomothetic approach to develop a nomological network combining neuro-immune and neurocognitive phenome markers to predict OSOS and cross-validate a diagnostic class generated replicable models reflecting the key phenome of the illness, which may mediate the effects of genome X environmentome interactions on the final outcome phenome features, namely symptomatology and phenomenology.

No studies have examined the immune fingerprint of major neuro-cognitive psychosis (MNP) or deficit schizophrenia using M1 macrophage cytokines in combination with chemokines such as CCL-2 and CCL-11. The present study delineated the neuro-immune fingerprint of MNP/deficit schizophrenia by analyzing plasma levels of IL-1β, sIL-1RA, TNF-α, sTNFR1, sTNFR2, CCL-2 and CCL-11 in MNP (n=120) versus healthy controls (n=54) in association with neurocognitive deficits (as assessed with the Brief Assessment of Cognition in Schizophrenia) and PHEMN (psychotic, hostility, excitation, mannerism and negative) symptoms. All immune biomarkers were significantly higher in MNP than in normal controls. MNP was best predicted by a combination of CCL-11, TNF-α, IL-1β and sIL-1RA which yielded a bootstrapped (n=2000) area under the Receiver Operating Curve of 0.985. Composite scores reflecting M1 macrophage activity and neurotoxic potential including combined effects of CCL-11 plus CCL-2 were significantly increased in MNP. Nevertheless, the effects of increased IL-1β and TNF-α in MNP were attenuated (statistically) by increased sIL-1RA and sTNFR2, two negative immune-regulatory markers. A large part of the variance in PHEM (38.4%-52.6%) and negative (65.8-7439%) symptoms was explained by combinations of immune markers whereby CCL-11 was consistently the most important. The immune markers also explained a large part of the variance in the Mini Mental State examination, list learning, digit sequencing task, category instances, controlled word association, symbol coding and Tower of London. Soft Independent Modeling of Class Analogy performed on the biomarkers showed that the inter-class distance between the models constructed around MNP and controls was 19.3 indicating a good separation. Partial Least Squares analysis showed that 72.7% of the variance in overall phenomenology was explained by the regression on IL-1β, sIL-1RA, CCL-11, TNF-α (all positively) and education (inversely). It is concluded that the combination of the above-mentioned markers defines MNP as a distinct neuro-immune disorder and that those markers in combination explain a large part of the variance in memory and executivive impairments and PHEMN symptoms.

Objective: A previous study showed that schizophrenia is accompanied by lowered levels of trace/metal elements including cesium. There are no data whether changes in cesium, rubidium and rhenium are associated with activated immune-inflammatory pathways, cognitive impairments, and the symptomatology of schizophrenia. Methods: This study measured cesium, rubidium, and rhenium, cognitive impairments (using the Brief Assessment of Cognition in Schizophrenia) and the cytokines/chemokines interleukin (IL)-1β, tumor necrosis factor (TNF)-α, and CCL11 (eotaxin) in 120 schizophrenia patients and 54 healthy controls. Severity of illness was assessed using the Brief Psychiatric Rating Scale (BPRS), the Scale for the Assessment of Negative Symptoms (SANS), the Fibromyalgia and Chronic Fatigue Syndrome Rating (FF) Scale and the Hamilton Depression Rating Scale (HAM-D). Results: Serum cesium was significantly lower in schizophrenia patients as compared with controls. Serum cesium was significantly and inversely associated with CCL11 and TNF-α, but not IL-1β. Moreover, there were significant inverse associations between serum cesium levels and the BPRS, FF, HAM-D and SANS scores and positive correlations between cesium and neurocognitive probe results including the Tower of London, Symbol Coding, Controlled Word Association, Category Instances, Digit Sequencing Task, and List Learning tests. Conclusion: The results suggest that lowered serum cesium levels may play a role in the pathophysiology of SCZ, specific symptom domains including negative, depressive and fatigue symptoms, neurocognitive impairments (spatial working, episodic and semantic memory and executive functions) and neuro-immune pathways as well.

Three hundred ten 12-wek-old laying quails (155 each) were randomly selected from the initial population and kept in individual battery cages. The measurements of growth and egg production were determined to derive RFI. The relationship between RFI and egg quality, blood parameters and carcass characteristics was also determined. The results indicated that the gray quails had significantly higher egg mass and lower broken eggs compared to the white quails. A significant increase for eggshell strength and shell % was found in eggs produced from gray quails compared to white counterparts, although the shell thickness was the same. The results of multiple regression analysis clearly identified a significant effect of metabolic body weight and egg mass in computing expected feed intake rather than body weight gain in both varieties of Japanese quails. Strongly positive correlation between RFI and feed intake in both gray and white quail varieties was found. The same trend was also observed for feed conversion ratio (FCR). Therefore, including RFI in selection criteria of Japanese quail to improve FCR under high environmental temperature is highly recommended.

This study tries to focusing on applying information communication technology for economic importance of Mid Oil Company (MDOC), which is among contemporary oil companies in Iraq. Since ICT forms a significant aspect of achieving organizational economic objectives, most of public and private bodies seek to utilize ICT tool and techniques to improve work efficiencies. The emerging growth in ICT has made it process and service automation possible in managing organizational activities. To determine this effect of ICT on organizations, this study formulated statistical research model at MDOC through using fifteen questionnaires, which were distributed on three axes. The outcome of the questionnaire analysis revealed that there is inadequate comprehensive infrastructure to suitably support ICT within the selected organization management. In addition, it revealed that there are no ideal standards to maintain and sustain internet networks. Based on these revelations, the study presents recommendation for the adoption of ICT with the aim of minimizing cost, enhancing communication and managing infrastructure. Also recommends the need to support IT department within an organization, with essential equipment, in terms of man and machine, for better efficiency to employ the key of ICT Impact in Iraqi governmental oil companies.

A subset of patients with schizophrenia experience physio-somatic symptoms reminiscent of chronic fatigue and fibromyalgia. In schizophrenia, these symptoms contribute to impaired quality of life, and are strongly related to neuro-cognitive deficits, and increased IgA responses to tryptophan catabolites. Negative and PHEM (psychosis, hostility, excitation, mannerism) symptoms, psychomotor retardation (PMR) and formal thought disorders, appear to be manifestations of a single trait reflecting overall severity of schizophrenia (OSOS). In this study, 120 patients with deficit schizophrenia (DEFSCZ) and 54 healthy subjects were assessed with the FibroFatigue (FF) rating scale, and the above-mentioned symptom domains as well as neuro-cognitive tests and biomarkers were measured. In DEFSCZ, there were robust associations between the FF score and all above-mentioned symptom domains, and impairments in semantic and episodic memory and executive functions. Furthermore, the FF score loaded highly on an OSOS latent vector (LV), which showed adequate convergent validity, internal consistency reliability and predictive relevance and fitted a reflective model. Soft Independent Modelling of Class Analogy (SIMCA) showed that the FF items discriminated DEFSCZ from controls with an overall accuracy of 100%. Interleukin IL-1β, IL-1 receptor antagonist (sIL-1RA), tumour necrosis factor (TNF)-α and CCL-11 (eotaxin) explained 66.8% of the variance in the FF score and 59.4% of the variance in OSOS. In conclusion, these data show that physio-somatic symptoms are a core component of the phenomenology of DEFSCZ and are largely mediated by neurotoxic effects of activated immune pathways, including aberrations in CCL-11, IL-1β and TNF-α signalling.

Background: Aberrations in endothelial cells, immune and oxidative pathways are associated with atherosclerosis (ATS) and unstable angina (UA). The role of trace elements, minerals, and the endogenous opioid system (EOS) in UA are less well established. Methods: We measured lipid, insulin resistance (IR), and immune, trace element (copper and zinc), mineral (magnesium, calcium), EOS (β-endorphin and mu-opioid receptor (MOR)) and antioxidant (vitamin D3) biomarkers in patients with ATS (n=60) and UA (n=60) and healthy controls (n=58). Results: ATS patients showed increased atherogenic and IR indices, IL-6, IL-10, β-endorphin, copper and magnesium, and lower zinc than healthy controls. Logistic regression showed that UA was significantly discriminated from ATS without UA with an accuracy of 85.5% using calcium, IL-10, β-endorphin, MOR, triglycerides, IR (all positively), and copper and vitamin D3 (inversely). Neural networks showed that UA was discriminated from ATS without UA with an area under the ROC curve of 0.942 using MOR, β-endorphin, calcium, insulin resistance, vitamin D3 and copper as input variables. We found that 50.0% of the variance in IR was explained by the regression on copper, IL-10, IL-6 (all positively), and zinc (inversely), while 32.9% of the variance in the atherogenic index of plasma was explained by copper, IL-10 (both positively), and magnesium (inversely). Conclusion: UA is not only mediated by insulin resistance, atherogenicity, and immune disorders, but also by aberrations in the endogenous opioid system and trace elements as well as lowered antioxidant levels. Copper appears to play a key role in IR and atherogenicity.

Balancing the efficiency and robustness of food systems is a well-known trade-off process. Over-optimization of efficiency may lead to excessive use of resources. On the other hand, under-optimization of efficiency may lead to excessive waste of resources. Using non-parametric methods can help in developing actionable frameworks through which decision-makers and stakeholders can effectively balance and improve food systems' efficiency and robustness. Under this context, this paper presents a new structured approach integrating two well-suited non-parametric methods for analyzing and balancing the interconnection between the efficiency and robustness of food systems. This approach consists of three main steps. First, the slacks-based data envelopment analysis (SBM-DEA) is utilized to analyze the efficiency of five food robustness dimensions. Second, the weighted efficiency of these dimensions is computed and analyzed to provide an insight into their influence on the food system efficiency. Finally, two search methods were developed to identify opportunities for improving efficiency and robustness. The outcomes of these methods have been analyzed and validated to ensure their effectiveness and viability. The operational and mathematical properties of the proposed approach were evaluated using data from thirty-seven food-producing countries. The weights of the robustness dimensions in this study were determined using the analytic hierarchy process (AHP) method. The input matrix of the AHP was constructed using expert judgment and consultations with stakeholders. The results of this study have shown an appropriate level of applicability and effectiveness of the proposed approach. While the first search method provided valuable insights, the second method proved to be more effective in identifying the sources of inefficacy of robustness dimensions. Several conclusions have been drawn and reported with some recommendations for future research works.

Load variations in any power system result in losses escalation and voltage drops. With the sensible and optimal allocation of distributed generators (DGs), these problems could be considerably mitigated. It has been seen in the priorly existing methods that ideally allocation of DGs has been carried out during fixed loads and constant power requirements. However, in real scenarios the loads are always variable and allocation of DGs must be done in accordance to the variations of the connected load. Therefore, the current paper addressed the aforementioned problem by distinctive optimal allocation of DGs for each variability of 24hour load horizon. However, the single exclusive solution is considered among all allocations of 24 hours. The min-max regret concept has been utilized in order to deal with such methodology. Altogether, 24 scenarios are analyzed wherein each scenario corresponds to a specific hour of the respective day. The optimal allocation of DGs in terms of their optimal sizing and placement has been carried out by using three algorithms including battle royal optimization (BRO), accelerated particle swarm optimization (APSO) and genetic algorithm (GA). The multi-objective optimization problem is evaluated on the basis of minimum value criterion of the multi-objective index (MO). MO comprises of active and reactive power losses and voltage deviation. Hence, in order to find robustness of proposed technique, Conseil international des grands réseaux electriques (CIGRE’s) MV benchmark model incorporating 14 buses has been considerably used as a test network. In the end the results of three proposed algorithms have been compared.

In December 2019, an animal human coronavirus transmission occurred in Wuhan, China. A state of global pandemic was shortly declared, among a very rapid contagious spread of the virus. The causative virus was identified as SARS CoV 2 virus and is genetically related to the previous SARS outbreak in 2003. The virus causes wide clinical spectrum from mild flu like symptoms to adult respiratory distress syndrome. Kidney involvement has been reported in several reports in patients with various degrees of severity of SARS CoV2 infection. As knowledge is evolving, the accurate incidence of AKI is not known. Many questions are yet to be answered as regards the effect of epidemiological variables and comorbidities on the occurrence of AKI. Some reports have observed the occurrence of hematuria and proteinuria in a percentage of infected patients. Moreover, chronic kidney disease has not been found in some reports to add to the adverse outcomes, an aspect that merits further exploration. Patients on regular hemodialysis may be vulnerable to contagion due to lower status of immunity and need for frequent attendance to healthcare facilities. Due to the previous factors, prevention and mitigation of SARS CoV2 virus in this vulnerable population constitutes a major challenge.

Abstract: This paper aimed to investigate the entrepreneurial intentions of female students in Saudi Arabia, utilizing the Theory of Planned Behavior (TPB) as the theoretical framework. Employing a quantitative research methodology, data was collected through a questionnaire administered to female students at Princess Nourah University. The results revealed a positive inclination towards entrepreneurship, with over 64% expressing a desire to pursue entrepreneurial ventures in the future. This optimistic trend among female students suggests a potential pool of future entrepreneurs. Interestingly, a small percentage (3.21%) categorically rejected entrepreneurship as a career option, indicating a relatively low level of disinterest in entrepreneurial pursuits. However, many respondents (32%) remained undecided, presenting a valuable opportunity for mentorship and support to cultivate their entrepreneurial intentions. These findings underscore the significance of providing guidance and education to encourage entrepreneurship among female students. The TPB analysis highlighted that attitudes and perceived behavioral control towards entrepreneurship were favorable among female students, indicating a positive mindset and belief in their ability to embark on entrepreneurial endeavors. However, societal norms still exert a negative influence on some student’s entrepreneurial intentions, suggesting a need to address cultural barriers that might hinder female students' willingness to pursue entrepreneurship. The study suggests enhancing female entrepreneurship through societal encouragement and support from personal networks. It highlights the importance of fostering entrepreneurial aspirations in female students. Crucially, the study underscores the role of universities in cultivating entrepreneurial intentions by proposing the implementation of entrepreneurship-focused curricula and the creation of university-based training units or incubators.

This paper aims to study and analyze the effect of the flow rate and amplitude of walling waves on the peristaltic flow of Jeffrey’s fluid through an irregular channel. In addition, it analyses streamlined patterns and their local and global bifurcation flow. The theory of dynamical systems is used to explore the position of critical points and their bifurcation. Numerical and analytical methods are presented to display effective changes in amplitude and rate of the flow on the transport of fluid. Three types of streamline patterns occur backward, trapping and augmented flow in the channel through movement due to changes in the value rate parameters.

The hydrocarbon generation potential of Chia Gara strata and their genetic link with produced oils from the Zagros basin are still not comprehensively investigated. Forty-seven rock samples from the Tithonian–Berriasian interval were subjected to geochemical analyses to infer organic matter enrichment, hydrocarbon potential, thermal maturity, and timing for hydrocarbon generation/expulsion and their implications regarding upcoming petroleum explorations in the Zagros basin. The results showed that the Chia Gara rock samples have fair to very-good generation potential, as confirmed by higher total organic carbon (TOC=0.68–3.95 wt%) and Rock-Eval (S1+S2=3.37–8.52 mg HC/g rock). The hydrogen index (HI=171–462) and Rock-Eval Tmax over 430 °C support the presence of Types II and mixed Types II/III kerogen. These results confirm the high generation potential of the Chia Gara Formation in the study region. 1D basin models of the KK–109 well show that over 55% of kerogens were converted into oil in the Cretaceous (77–67 Ma). Expulsion started from the Miocene until now (22–0 Ma), consistent with 0.71–0.80 of modeled Easy%Ro and 55–80 %TR. Consequently, this project confirms the potential oil expulsion from the Chia Gara Formation, which can be a resource for upcoming hydrocarbon investigation in the Zagros basin, Iraq.

Peste des Petits Ruminants (PPR) is one of the major transboundary animal diseases that severely impact livestock production and trade worldwide. An investigation was carried into the seroprevalence and risk factors of PPR in small ruminants, camels, and wild ruminants in Bahrain. A total of 1240 serum samples were collected from 119 sheep flocks and 1224 serum samples from 125 goat herds. In addition, 100 sera from camels and 38 sera from wild ruminants, were collected. Serum samples were tested for the presence of PPR specific antibodies using a competitive ELISA. Flock management and health information of the flocks and herds were collected using a semi-structured questionnaire. The individual prevalence of PPR in sheep and goats was 26% and 25.5%, respectively. The flock or herd level prevalence of PPR was 22.7% and 29.6% in sheep and goats, respectively. None of the tested camels or wild ruminants were positive for PPR-specific antibodies. Sheep and goats from the Northern governorate were more likely to be seropositive to PPR than in other governorates. On the individual animal level, the univariate analysis suggested; age (<12 months), sex (male), and health status (weak animals) as risk factors for PPR seropositivity. On the flock/herd level, the multivariable logistic regression analysis identified large flock/herd size and semi-intensive farming as risk factors for PPR seropositivity.

This study presents a novel technique utilizing high frequency vibration to shorten treatment time and preserve alveolar bone in challenging orthodontic cases treated with Invisalign® clear aligners. Four non-growing orthodontic patients (age range 14-47 years old) with Class II skeletal patterns (convex profiles with retrognathic mandibles) who sought correction of their crowded teeth and non-surgical correction of their convex profiles were included in this study. These patients were treated using Invisalign clear aligners together with high frequency vibration (HFV) devices (120 Hz) (VPro5™) that were used by all patients for five minutes per day during active orthodontic treatment. Vertical control and forward rotation of the mandible for each patient was achieved through pre-programming the Invisalign to produce posterior teeth intrusion. Successful forward rotation of the mandibles achieved in all patients led to improvement of their facial convex profiles (ANB improved 2.1 + 0.5 degrees; FMA improved 1.2 +1.1 degrees). Dental decompensation was achieved by lingual tipping of the lower incisors and palatal root torque of upper incisors. The use of HFV together with Invisalign facilitated achieving these results within a 12+6 month period. In addition, more bone labial to the lower incisors after their lingual movement was noted. In conclusion, the use of HFV concurrent with SmartTrack Invisalign aligners allowed complex tooth movement and forward projection without surgery in non-growing patients with skeletal Class II relationships. The clinical impact and implications of this case series is that the use of HFV facilitates complex orthodontic tooth movement including posterior teeth intrusion and incisor decompensation in addition to increased bone formation labial to lower incisors that may minimize future gum recession due to their labial inclination.

Anthrax is a severe acute zoonotic disease of herbivores caused by Gram-positive, anaerobic, spore-forming bacteria. It is transmitted via direct contact with sick farm animals or those who have died of Anthrax. This study intends to present a cutaneous form of Anthrax in a 36-year-old woman suffered from a painless ulcer on her thumb five days after handling a head of sheep. The lesion started as a small papule that developed as a painless vesicular blister on the dorsal exterior surface of the right thumb. However, upon clinical investigation, the patient showed an absence of fever, lethargy, and pain. Swabs were collected and examined according to conventional microbiological tests. Direct smear revealed a Gram-positive bacilli that showed spore formation resembling B. anthracis. Nutrient agar, 5% sheep blood agar, and PLET agar were streaked by the swab. Other swabs were inoculated into the peptone water. All cultured media were inoculated at 37 oC for 24 hours. The morphology of growing colonies was examined, while the biochemical tests were done to identify the isolated bacteria, including a motility test and antibiotic sensitivity. The results of this study approved the existence of Bacillus anthracis by microbiological analyses. Accordingly, cutaneous form of anthrax was diagnosed, and specific systematic and local treatments were provided for the patient. In conclusion, this study confirmed the diagnosis of cutaneous Anthrax, a highly contagious disease that needed early detection and more attention and awareness should be taken when handling animal products.

Deadlock is a real problem that can cause expensive, time-dependent hang-ups or failures in distributed computing systems. Some studies have been conducted with deadlock detection and resolution in generalized request computing models, most of these studies are based on the diffusing computation scheme, where forward and backward propagated probe and reply messages respectively are diffused between dependent processes. The replies carry the dependency information between processes for the initiator. Using this dependency information initiator can detect and resolve the deadlock cycle. It has been proven in the literature that a deadlock cycle length distribution is skewed with a large majority of cycles (90%) having length two. Based on this fact an improved algorithm is proposed for handling deadlock detection in distributed computing systems under the distributed request model where each process has several requests at a time. The improved algorithm depends mainly on message propagation and timeout policy. Probe and reply messages are propagated between the initiator and its successors only to detect deadlock cycles between them. Global timeout policy is used to detect potential deadlock cycles with large length distribution. The proposed algorithm can handle concurrent executions. Simulation experiments are performed to see the effectiveness of the improved algorithm. It is found that the improved algorithm compares favorably with other existing algorithms and it shows better results for several performance metrics especially in reducing deadlock latency and execution time.

Photocatalytic processes offer promising solutions for environmental remediation and clean energy production, yet their efficiency under visible light remains a significant challenge. Here, we report a novel silver-graphene (Ag-G) modified TiO2 (Ag-G-TiO2) nanocomposite photocatalyst that demonstrates remarkably enhanced photocatalytic activity for both dye wastewater degradation and hydrogen production under visible and UV light irradiation. Through comprehensive characterization and performance analysis, we reveal that the Ag-G modification narrows the TiO2 bandgap from 3.12 eV to 1.79 eV, enabling efficient visible light absorption. The nanocomposite achieves a peak hydrogen production rate of 191 μmolesg-1h-1 in deionized water dye solution under visible light, significantly outperforming unmodified TiO2. Intriguingly, we observe an inverse relationship between dye degradation efficiency and hydrogen production rates in dye solutions with tap water versus deionized water, highlighting the critical role of water composition in photocatalytic processes. Our findings demonstrate sustained hydrogen production under visible light and rapid initial rates under UV irradiation, underscoring the versatility of Ag-G-TiO2 catalyst. This work not only advances our understanding of fundamental photocatalytic mechanisms but also presents a promising material for solar-driven environmental and energy applications, potentially contributing to the global transition towards sustainable technologies.

Leveraging the liquid phase immiscibility effect and phase diagram calculations, a sequence of alloy powders with varying Fe content was designed and fabricated utilizing gas atomization method. Microstructural characterizations, employing SEM, EDS, and XRD analyses, revealed the successful formation of incomplete shell on the surfaces of Al-Bi-Fe powders, obviating the need for Sn doping. This study systematically investigated the microstructure, hydrolysis performance, and hydrolysis process of these alloys in deionized water. Notably, Al-10Bi-7Fe exhibited the highest hydrogen production, reaching 961.0 Nml/g, while Al-10Bi-10Fe demonstrated the peak conversion rate at 92.99%. The hydrolysis activation energy of each Al-Bi-Fe alloy powder was calculated using the Arrhenius equation, indicating a reduction in activation energy achieved through Fe doping.

this paper focuses on a scientific study of the restoration, rehabilitation and reuse of the great throne hall, the most important hall in al-jawhara palace. it also aims to study the most important factors and forces of damage that affected the great throne hall, natural, biological, and human, and the resulting damage. field tests were performed, laboratory tests to determine fracture stress, liquidity and spandex limits tests, chemical analysis on soil samples and geoelectrical testing of the soil, and the results did not show caves or voids in the ground until a depth of 10.00 m, construc-tion materials were studied and tested using x-ray, (xrd), mechanical tests (tensile, shear, com-pression), and a study of the effect of seismic loads on the walls; the results showed horizontal and vertical cracks; based on the study and analysis of these cracks, it was possible to present modern techniques in restoration and reinforcement methods, and in conclusion, the researcher's recommendations.

Peer-to-peer (P2P) content distribution or file sharing system aims to facilitate the dissemination of large files over unreliable networks. Network coding is a new transmission technique that has captured the interest of researchers because of its ability to increase throughput and robustness of the network, and decrease the download time. In this survey paper, we extensively summarize, assess, compare, and classify the most recently used techniques to improve P2P content distribution systems performance using network coding. To the best of our knowledge, this survey is the first comprehensive survey that specifically focuses on the performance of network coding based P2P file sharing systems.

The simultaneous evaluation of heat/mass transference procures momentous significance in the polymer industry and engineering activities. Extensive utilization of such aspects includes propylene flares, heat exchangers, energy transfiguration in chilling towers, and amputation of post fortuitous heat in nuclear reactors. Owing to such prospective demands, we interpreted the Jeffrey liquid reactive flow under non-linear convection. We scrutinized the transference of heat/mass under generalized Fourier-Fick relations. Thermal conductivity depends on temperature while mass diffusivity is dependent on concentration. Besides, heat source along with first-order chemical reaction aspects are accounted for. Relevant transformations are exerted to achieve non-linear differential systems that are solved through the homotopy scheme. Influences of divers factors are exhibited via graphical benchmark.

Abstract: The main contribution of this paper is to introduce a new iterative training algorithm for restricted Boltzmann machines. The proposed learning path is inspired from online sequential extreme learning machine one of extreme learning machine variants which deals with time accumulated sequences of data with fixed or varied sizes. Recursive least squares rules are integrated for weights adaptation to avoid learning rate tuning and local minimum issues. The proposed approach is compared to one of the well known training algorithms for Boltzmann machines named “contrastive divergence”, in term of time, accuracy and algorithmic complexity under the same conditions. Results strongly encourage the new given rules during data reconstruction.

Description of a novel bovine antimicrobial peptide and its antimicrobial spectrum. RNA isolation and RT-PCR were done from various tissues. DCD peptide was synthesized, and antimicrobial activity was analyzed. Bovine dermcidin gene contains five exons intermittent by 4 introns. Bovine DCD-mRNA was 398 bp with ORF 336 bp. Bovine DCD was expressed in skin and blood. Analysis of the amino acid compositions revealed that cysteine was repeated 6 times indicating the presence of 3 disulfide bonds that play role in the peptide stability. Staphylococcus epidermidis, Streptococcus bovis, and Enterococcus faecalis were affected by Bovine DCD peptide. Highest antimicrobial effect was at 50 and 100 µg/ml. The effect on Escherichia coli and Candida albicans was slightly low. In all bacteria, Bovine DCD peptide activity did not affect by varying pH values, but in Staphylococcus aureus, the activity was affected greatly at pH 4.5 and 5.5. The optimum salt concentrations were 100 and 50 mM NaCl with all bacterial strains and E. coli, respectively. In case of C. albicans, the antimicrobial activity of Bovine DCD peptide decreased with increasing the pH value regardless the NaCl concentration. The pH 6.5 of the sweat buffer was the optimum for the Bovine DCD peptide activity.

The tryptophan catabolite (TRYCAT) pathway is implicated in the pathophysiology of schizophrenia (SCZ) since the rate-limiting enzyme indoleamine-dioxygenase (IDO) may be induced by inflammatory and oxidative stress mediators. This systematic review searched PubMed, Web of Science, and Google Scholar for papers published from inception until August 2021 and meta-analyzed the association between SCZ and TRYCATs in the central nervous system (CNS) and peripheral blood. We included 61 studies comprising 2813 patients and 2948 healthy controls. In the CNS we found a significant (p<0.001) increase in the kynurenine/tryptophan (KYN/TRP) (standardized mean difference, SMD=0.769, 95% confidence interval, CI: 0.456; 1.082) and kynurenic acid (KA)/KYN+TRP (SMD=0.697, CI:0.478-0.917) ratios, KA (SMD=0.646, CI: 0.422; 0.909) and KYN (SMD=1.238; CI: 0.590; 1.886), while the 3OH-kynurenine (3HK) + KYN-3-monooxygenase (KMO)/KYN ratio was significantly reduced (SMD=-1.089, CI: -1.682; -0.496). There were significant differences between KYN/TRP, (KYN+KA)/TRP, (3HK+KMO)/KYN, KA, and KYN levels among the CNS and peripheral blood, and among serum and plasma KYN. The only useful peripheral marker of CNS TRYCATs findings was the increased KYN/TRP ratio in serum (SMD=0.211, CI: 0.056; 0.366, p=0.007), but not in plasma. There was no significant increase in a neurotoxic composite score based on KYN, 3HK, and picolinic, xanthurenic, and quinolinic acid. SCZ is accompanied by increased IDO activity in the CNS and serum, and reduced KMO activity and a shift towards KA production in the CNS. This CNS TRYCATs profile indicates neuroprotective, negative immunoregulatory and anti-inflammatory effects. Peripheral blood levels of TRYCATs are dissociated from CNS findings except for a modest increase in serum IDO activity.

The Last Planner System (LPS) aims to enhance planning reliability by reducing variability in construction processes. While LPS applications have been explored in construction and detailed design, its application in architectural design remains underrepresented due to its abstract nature. This study addresses this gap by proposing an LPS framework tailored for architectural design, utilizing LPS metrics to assess planning reliability. Key issues hindering formal planning methods' implementation are identified, and relevant LPS principles are aligned with these challenges, culminating in a conceptual LPS model designed for architectural projects. Building upon the conceptual model, an implementation model is then developed and put into practice within an architectural design company in the United States, resulting in measured improvements in planning reliability and responsiveness. Additionally, it unveils hidden challenges associated with emerging tasks, guiding future design process enhancements. This study demonstrates how tracking design planning performance with LPS metrics can promote LPS adoption in architectural design, offering a benchmark for necessary interventions to achieve desired performance in architectural design.

This work can be considered as a first step of designing a future competitive data-driven approach for remaining useful life prediction of aircraft engines. The proposed approach is an ensemble of serially connected extreme learning machines. The results of prediction of the first networks are scaled and fed to the next networks as an additive features to the original inputs. This feature mapping allows increasing the correlation of training inputs with their targets by holding new prior knowledge about the probable behavior of the target function. The proposed approach is evaluated under remaining useful estimation using a set of “time-varying” data retrieved from the public dataset C-MAPSS (Commercial Modular Aero Propulsion System Simulation) provided by NASA. The prediction performances are compared to basic extreme learning machine and proved the effectiveness of the proposed methodology.

Ti-Al based alloys, particularly TiAl and Ti3Al two-phase alloys, have garnered significant attention as potential replacements for various high-temperature structural materials due to their exceptional properties, including low density, oxidation resistance, and high strength at elevated temperatures. Despite these advantages, experimental studies on the microstructure evolution of Ti-Al based alloys under complex conditions remain challenging to observe and characterize. This review article examines the current research on molecular dynamics (MD) simulations of Ti-Al based alloys, focusing on two-phase Ti-Al alloys, Ti-Al amorphous alloys, Ti-Al composite materials, and the welding and multi-layer/film applications of Ti-Al alloys. The review highlights the unique capabilities of MD simulations in predicting the behavior of Ti-Al based alloys and addresses existing scientific challenges. Furthermore, the article discusses future research directions and development prospects in this field.

Background: Our knowledge of prostate cancer (PCa) genomics mainly reflects European (EUR) and Asian (ASN) populations. Our understanding of the influence of Middle Eastern (ME) and African (AFR) ancestry on the mutational profiles of prostate cancer is limited. Design, setting and participants: To characterize genomic differences between ME, EUR, ASN and AFR ancestry, fluorescent in situ hybridization (FISH) studies for NKX3-1 deletions and MYC amplification was carried out on 42 tumors arising in individuals of ME ancestry. These were supplemented by analysis of copy number profiles of 401 tumors of all ancestries. Outcome measurement and statistical analysis: FISH results of NKX3-1 and MYC were assessed in the ME cohort and compared to other ancestries. Gene level copy number aberrations (CNAs) for each sample were statistically compared between ancestry groups. Results and Limitation: NKX3-1 deletions by FISH were observed in 17/42 (17.5%) prostate tumors arising in men of ME ancestry, while MYC amplifications were only observed in 1/42 (0.23%). Using CNAs called from arrays, the incidence of NKX3-1 deletions was significantly lower in ME vs. other ancestries (20% vs. 52%; p = 2.3 x 10-3). No differences in MYC amplifications was noted between the two cohorts using array-based CNAs. Across the genome, tumors arising in men of ME ancestry had fewer CNAs than those of other ancestries (p = 0.014). Additionally, the somatic amplification of 21 specific genes was more frequent in tumors arising in men of ME vs. EUR ancestry (Proportions test; Q < 0.05). Those included amplifications in the glutathione S-transferase family on chromosome 1 (GSTM1, GSTM2, GSTM5) and the IQ Motif Containing family on chromosome 3 (IQCF1, IQCF2, IQCF13, IQCF4, IQCF5, IQCF6). Conclusion: Significant differences in genetic background exists between different ancestries. The lower number of somatic CNAs observed in prostate cancer arising in men of ME ancestry may explain the relatively good prognosis in this population. Larger studies are warranted.

In this project, four of fibers Bragg gratings were fabricated by injecting different volumes of liquids (star line Glass Mechanix optical adhesive material, olive oil diluted with ethanol) into the hollow core fiber. The amplitude splitting interferometric technique with a high resolution specially designed translation stage was used for the fabrication process. The fabrication was done using ultraviolet laser operated at wavelength 405nm. The fabricated Bragg length of the four fibers is equal to 3.8 cm. The results presented fiber Bragg grating (FBG) with successful fabrication at 653.3 nm Bragg reflected wavelength.

It is well known that fiber sizing is one of the most important component in the manufacturing of composites, and it does affect the mechanical properties including strength and stiffness. In this work, the influence of fiber sizing levels on the mechanical properties of carbon fibers (CF) is reported at room temperature by using single fiber tensile testing (Favimat+), single fiber pullout testing (SFPO), and interfacial elemental analysis using X-ray photoelectron spectroscopy (XPS). Standard modulus of CF (7±0.2 μm in diameter) were sized using two Michelman commercially available sizing formulations. The average solid content for each sizing formulation is 26.3 ± 0.2% and 34.1 ± 0.2%, respectively. HEXION RIMR 135 with curing agent RIMH 137 was used as a model thermoset epoxy matrix during the SFPO measurements. A predictive engineering fiber sizing methodology is also developed. Sizing amounts of 0.5, 1, and 2 wt. % on the surface of the fiber is achieved for both sizing formulations. For each fiber sizing level, 50 single fiber tensile testing experiments and 20 single fiber pull-out tests were conducted. The ultimate tensile strength (σult) of the carbon fibers and the interfacial shear strength (τ_app) of the single fiber composite were analyzed. it is also investigated the effect of the sizing levels on the interfacial shear stress and the O/C (Oxygen/Carbon) surface composition ratio. As a result, generalized fiber sizing and characterization methods were established. The developed methods can be used to characterize the strength and interfacial shear strength of any man-made fibers with different sizing formulations and solid contents, irrespective of the matrix i.e. thermoset or thermoplastic.

Survivability is a critical concern in WSNs, heavily influenced by energy efficiency. Addressing severe energy constraints in WSNs requires solutions that meet application goals while prolonging network life. This paper presents an energy optimization approach (EOAMRCL) for WSNs, integrating the Grey Wolf Optimization (GWO) for enhanced performance. EOAMRCL aims to enhance energy efficiency by selecting the optimal duty-cycle schedule, transmission power, and routing paths. The proposed approach employs a centralized strategy using a hierarchical network architecture. During the cluster formation phase, an objective function, augmented with GWO, determines the ideal cluster heads (CHs). The routing protocol then selects routes with minimal energy consumption for data transmission to CHs, using transmission power as a metric. In the transmission phase, the MAC layer forms a duty-cycle schedule based on cross-layer routing information, enabling nodes to switch between active and sleep modes according to their network allocation vectors (NAV). This process is further optimized by an enhanced CSMA/CA mechanism, which incorporates sleep/activate modes and pairing nodes to alternate between active and sleep states. This integration reduces collisions, improves channel assessment accuracy, and lowers energy consumption, thereby enhancing overall network performance. EOAMRCL was evaluated in a MATLAB environment, demonstrating superior performance compared to EEUC, DWEHC, and CGA-GWO protocols, particularly in terms of network lifetime and energy consumption. This highlights the effectiveness of integrating GWO and the updated CSMA/CA mechanism in achieving optimal energy efficiency and network performance.

This article examines the complex interactions of the multiplier effect within the realm of tourism, with a specific emphasis on national parks. The main objective is to evaluate the multiplier effect within national parks, specifically focusing on Buiratau State National Nature Park in Kazakh-stan as a case study. The multiplier effect is a fundamental principle in the field of economic analysis. Economic multiplier effect is the term used to describe the occurrence when an initial infusion of spending in a certain industry leads to subsequent rounds of extra and sustainable economic activity. In the context of national parks, this phenomenon arises when visitor expendi-tures result in several favorable consequences, including increased employment, infrastructure advancement, and general economic expansion. The article seeks to measure the multiplier effect of tourism activities in Buiratau State National Nature Park through a thorough assessment. This entails examining several variables and datasets pertaining to visitor expenditure and its influ-ence. The study contributes to the existing literature by examining a recently constructed national park in a developing country. It compares the findings of this park with well-established national parks in other areas, emphasizing the distinct problems and opportunities it presents. Further-more, the research presents a methodological framework for evaluating the multiplier effect of national parks, which may be utilized in comparable contexts. This research ultimately enhances our comprehension of the economic implications of national parks and emphasizes their function as drivers for local and regional growth.

Background and objectives: The initiation of apoptotic death in cancer cells is the aim of many chemotherapeutic strategies. As many anticancer agents have been discovered in natural plant sources, the search for novel phytochemicals displaying anticancer activities continues at a tremendous rate. This study was conducted to evaluate the effect of extractable polyphenols (EPP); non-extractable polyphenols (NEPP); nobiletin (NOB); tectorigenin (TEC) and persicogenin (PERS) from Barhi date palm kernels (BDPK) extracts on the induction of apoptosis in human lung cancer A549 and colon cancer HT29 cell lines. Materials and Methods: The anticancer activities were determined using MTT and trypan blue exclusion assays. Flow cytometry analysis was performed to study the cell viability, cell cycle arrest and apoptosis. The underlying mechanism of apoptosis induced by crude extracts and the purified compounds was investigated using caspase-3, -8 and -9 assays and the mitochondrial membrane potential assay. Results: The findings indicate that both BDPK extracts and the purified compounds do exert induced cell death on A549 and HT29 cells. The results observed from MTT- assay and trypan blue exclusion indicate that the cytotoxic effects of both plant extracts and the three isolated flavonoids are dose-dependent with higher cell death after 72 hours treatment. Treatment of human lung and colon cancer cells with EPP, NEPP, NOB, TEC and PERSI induced late stages of apoptosis as there was evidence of the DNA degradation and high percentage of the cells population was situated at sub-G1 phase, indicating a high population of apoptotic cells. Conclusions: Study of the apoptotic mechanism demonstrated that EPP and NEPP exhibited dependent mitochondrial signalling pathway as seen with caspase-9 and induced receptor-mediated (extrinsic) apoptotic pathway as seen with caspase-8. Therefore, our results suggest that BDPK extracts and the three isolated flavonoids could be a good candidate for developing anticancer agents.

Despite the effectiveness of insulin injections in managing hyperglycemia in Type 1 Diabetes, they fall short in addressing autoimmunity and regenerating damaged islets. This review aims to explore the potential of various treatment modalities for T1DM, including mesenchymal stem cells (MSCs), MSC-derived exosomes, gene therapy, islet allotransplantation, and pancreatic islet cell transplantation. Results: MSCs demonstrate efficacy in T1DM treatment through immunomodulation and tissue regeneration, although further research is warranted to optimize their therapeutic potential. Gene therapy presents a promising approach despite challenges such as donor shortage and immune rejection. Pancreatic islet cell transplantation emerges as a viable option, albeit with associated risks including graft rejection and the need for immunosuppression. Teplizumab, an FDA-approved humanized monoclonal antibody, revolutionizes the treatment landscape of Type 1 Diabetes by significantly delaying its onset, offering a paradigm shift since the discovery of insulin Conclusion: Ongoing studies and technological advancements in T1DM management offer a promising outlook for improved treatments and possibly even eradication on a global scale. MSCs, MSC-derived exosomes, gene therapy, and pancreatic islet transplantation hold considerable potential.

Background and aims: For many surgical procedures, spinal anesthesia is a reliable and efficient anesthetic approach. Numerous drugs have been reported to be administered to intrathecal local anesthetics as adjuvants to increase the efficacy of spinal anesthesia. There is little evidence of the effect of intrathecal dexmedetomidine on pain scores and the consumption of analgesia postoperatively. Methods: After obtaining ethical approval, demographical and clinical data of patients who underwent surgical procedures under spinal anesthesia with intrathecal dexmedetomidine or fentanyl was collected and analyzed. Results: In this study with 96 patients, intrathecal dexmedetomidine (group D) resulted in significantly lower post-operative pain scores compared to intrathecal fentanyl (group F) (p=0.000). Across various surgical types, including Orthopedic, General, Urology, and Obs/Gyne procedures, group D consistently displayed reduced pain scores (p&lt;0.001). The number of patients who needed post-operative analgesia was significantly higher in group (F) than in group (D) (40 vs 23, p=0.002). Conclusion: Compared to fentanyl, intrathecal dexmedetomidine as an adjuvant to local anesthesia was found to lower post-operative pain scores and decrease the need for post-operative analgesia.

The literature study delves into novel therapeutic strategies in transplantation medicine, highlighting unique approaches that could revolutionize current practices. It emphasizes novel patterns that have the potential to transform the current landscape. Commencing with a thorough examination of the historical environment, it traces crucial advances and changes in transplantation. The focus is on traditional techniques, emphasizing their limitations and challenges. An extensive examination of contemporary transplantation therapies offers valuable insights into the most recent progress in organ, cellular, and tissue transplantation. This analysis examines the immunological obstacles and outlines the current advancements and constraints. The exploration further navigates into novel models and concepts such as immunomodulation, developments in organ preservation techniques, gene editing, biomaterials, scaffold-based solutions, and the integration of precision medicine, artificial intelligence, and machine learning applications. Each section analyzes the potential for change and current progress in various areas, backed by relevant scientific sources up to 2023. The subsequent sections delve into innovative cellular therapies, biotechnological progress, current clinical trials, and case studies demonstrating effective applications. This examination delves into the ethical and regulatory considerations of innovative therapeutic procedures, emphasizing ethical implications, regulatory frameworks, and the importance of balancing innovation with patient welfare. The literature review concludes by offering a forward-looking perspective, emphasizing potential progress, anticipated challenges, and advocating for collaboration and interdisciplinary approaches to overcome limitations in the field of transplantation medicine.

This paper presents PrognosEase; a software that provides an easier way to produce different types of run-to-failure data mimicking real-world conditions to simplify prognosis studies in terms of data collection and improvement in ML degradation modelling process. Different types of degradation types made available to meet different types of applications. Besides, some primary ML tests were performed to ensure that complexity patterns of real systems could be observed in the training/testing predictions attitude. This paper also presents the impacts, limitations and potential improvements of the data generator.

In this study, our primary objective was to analyze the tradeoff between accuracy and complexity in machine learning models, with a specific focus on the impact of reducing complexity and entropy on the production of landslide susceptibility maps. We aimed to investigate how simplifying the model and reducing entropy can affect the capture of complex patterns in the susceptibility maps. To achieve this, we conducted a comprehensive evaluation of various machine-learning algorithms for classification tasks. We compared the performance of these algorithms in terms of accuracy and complexity, considering both "before" and "after" scenarios of dimensionality reduction using Principal Component Analysis (PCA). Our findings revealed that reducing complexity and lowering entropy can lead to an increase in model accuracy. However, we also observed that this reduction in complexity comes at the cost of losing important complex patterns in the produced landslide susceptibility maps. By simplifying the model and reducing entropy, certain intricate relationships and uncertain patterns may be overlooked, resulting in a loss of information and potentially compromising the accuracy of the susceptibility maps. The analysis encompassed a diverse range of machine learning algorithms, including Random Forest (RF), Extra Trees (EXT), XGboost, LightGBM, Catboost, Naive Bayes (NB), K-Nearest Neighbors (KNN), Gradient Boosting Machine (GBM), and Decision Trees (DT). Each algorithm was evaluated for its strengths and limitations, considering the tradeoff between accuracy and complexity. Before dimensionality reduction, the algorithms demonstrated promising results, with RF exhibiting excellent AUC/ROC scores and average accuracy. However, computational costs were noted as a potential drawback for RF, especially when dealing with large datasets. EXT showcased robust performance and good accuracy, while XGboost demonstrated its ability to handle complex relationships within large datasets, albeit requiring careful hyperparameter tuning. The efficiency and scalability of LightGBM made it a suitable choice for large datasets, although it displayed sensitivity to class imbalance. Catboost excelled in handling categorical features, but longer training times were observed for larger datasets. NB showcased simplicity and computational efficiency but assumed independence among features. KNN, known for its capability to capture local patterns and spatial relationships, was found to be sensitive to the choice of distance metric. GBM, while capturing complex relationships effectively, was prone to overfitting without proper regularization. DT, with its interpretability and ease of understanding, faced limitations in terms of overfitting and limited generalization. After dimensionality reduction, certain algorithms exhibited improvements in their AUC/ROC scores and average accuracy, including RF, EXT, XGboost, and LightGBM. However, for a few algorithms, such as NB and DT, a decrease in performance was observed. This study provides valuable insights into the performance characteristics, strengths, and limitations of various machine learning algorithms in classification tasks. Researchers and practitioners can utilize these findings to make informed decisions when selecting algorithms for their specific datasets and requirements. We also aim to identify the potential factors contributing to the high accuracy rates obtained from these ensembled algorithms and explore possible shortcomings of non-ensembled algorithms that may result in lower accuracy rates. By conducting a comprehensive analysis of these algorithms, we seek to provide valuable insights into the benefits and limitations of ensembled approaches for landslide susceptibility mapping. Our study sheds light on the challenges faced when balancing accuracy and complexity in machine learning models for landslide susceptibility mapping. It emphasizes the importance of carefully considering the level of complexity and entropy reduction in relation to the specific patterns and uncertainties present in the data. By providing insights into this tradeoff, our research aims to assist researchers and practitioners in making informed decisions regarding model complexity and entropy reduction, ultimately improving the quality and interpretability of landslide susceptibility maps.

In this study, the olive pomace was considered because of its importance in the environment. So, this study carried out to estimate the total nitrogen content and the fatty acids profile of olive pomace. The olive pomace samples were collected from Irbid, Jarash, Ajloun and Mafraq during the harvesting season 2014 to study the biochemical characteristics of fatty acid composition and the total nitrogen (TN) content. The total nitrogen content was determined by standard Kjeldahl method and the fatty acid profile was detected by gas chromatography (GC). The results show that the total nitrogen content ranged from (0.39 ± 0.0) to (0.62 ± 0.02) with statistically significant difference suggesting that the composition of matrices and their percentage may be responsible for composition of amendments. The calculated total protein percentage ranged between (2.43 ± 0.00) to (3.87 ± 0.17). Also, 13 different fatty acids were quantitatively profiled and quantitated. Oleic acid (C 18:1) was found to be the highest percentage of all other fatty acids and ranged between (59.03%) and (63.81%), moreover the C 18:1/C 18:2 (oil quality) was calculated and C.V% showed variation meaning that nutritional implication could affect the oxidative stability of oils. In conclusion, OP by-product could give a sustainable and alternative-cheap source for fertilizers, pharmaceutical industries, cosmetics and other industries.

The variability of ozone over Egypt has been studied in this work. Higher values of coefficient of variation (COV) at eight stations occur at winter while lowest values occur at summer. The COV is function of latitude in annual, winter and spring where it decreases gradually from the north to south of Egypt. The trend analysis of ozone over the eight stations indicates negative trends over northern stations for both annual and seasonal time series with the greatest one at winter. The horizontal distribution of ozone trend values is negative over all Egypt in winter while it positive over middle and south Egypt in the other seasons. The long-term variability of the behavior of the annual ozone shows positive trend values in ozone are the dominant features during the period 1979- 1989 at the most stations. Negative trend values in ozone are the dominant features during the period 1990- 2014 at all stations. The Mann–Kendall test confirms that there is an abrupt change towards decreasing of ozone occurs in 1981, 1984, 2012, 1999, 2000, 1998 and 2010, while a change towards increasing of ozone appears in 2006, 2014, 1993 and 1989.

Demand for environmentally friendly types of energy is growing all over the world, which naturally increases the intensity of work on the production of hydrogen-containing fuel mixtures. Steam reforming of methanol is one of the most effective areas of research, as it is a process with low energy consumption. The results of steam reforming of methanol on the catalysts prepared by solution combustion synthesis (SCS) and impregnation by moisture capacity are presented. Investigation of the activity of Cu-Ce-Al catalysts of different composition was carried out for production of hydrogen and comparison of SCS with traditional impregnation method. Methanol conversion reaches 99%, while the selectivity of H2 was 88%, at 500 °C. It was found that CuAl2O4 spinel formation is due to substitution of Al3+ with Cu2+ Ce3+ cations. A consequence CuAl2O4 and CeAlO3 lattice parameters increase because of difference in ionic radius of Al3+ (0.53 Å) and Cu2+ (0.73 Å), Ce3+ (1.07 Å). Advantages of SCS catalysts in steam reforming of methanol were shown. The aim of this research is to develop a new catalyst for conversion of methanol into hydrogen containing fuel mixtures, which will further promote the organization of a new era of environmentally friendly energy-saving production methods.

Obesity is characterized by surplus buildup of body lipids primarily in adipose tissue. Prevalence and incidence of obesity are ascending persistently at an alarming rate. Unusual eating behaviors like compulsion to eat (food addiction) and excessive consumption are the premier contributors to obesity. Both are under influence of a variety of stimuli, mainly being stress, emotions, dietary restrictions, sweetness, hyperpalatability, neural pathways, hormonal imbalance and genetics. This review summarizes the potential driving factors behind overeating and food addiction for understanding and exploring obesity linked novel agents and processes as an endeavor to advance treatment approaches. Obesity has been studied extensively throughout the world due to high incidence and association with several metabolic disorders including cardiovascular disorders. The food addition has considered one of potential key factor of obesity and excessive weight gain. Sedentary life style and availability of food also induce obesity.

The study is based on the notion that big data predictive analytics is important for developing strategic alliances performance of companies. this study investigates the relationship between big data predictive analytics, big data culture, and competitive strategies 'techniques were adopted, such as descriptive statistics, correlation,regression, etc. using SPSS and SmartPLS statistical software. Hypotheses were tested with bootstrapped analysis using SEM (through SmartPLS). The study developed a structural equation model by using the SEM analysis. The results of the SEM analysis suggested the hypothesized model of the study was valid. The results supported all the hypotheses of the study.Through empirical analysis, demonstrated the conclusion is that the big data predictive analytics has a positive and significant relationship with strategic alliance performance

Automation is at the core of modern industry. It aims to increase production rates, decrease production costs, and reduce human intervention in order to avoid human mistakes and time delays during manufacturing. On the other hand, human assistance is usually required to customize products and reconfigure control systems through a special process interface called Human Machine Interface (HMI). Machine Learning (ML) algorithms can effectively be used to resolve this tradeoff between full automation and human assistance. This paper provides an example of the industrial application of ML algorithms to help human operators save their mental effort and avoid time delays and unintended mistakes for the sake of high production rates. Based on real-time sensor measurements, several ML algorithms have been tried to classify paper rolls according to paper grammage in a white paper mill. The performance evaluation shows that the AdaBoost algorithm is the best ML algorithm for this application with classification accuracy (CA), precision, and recall of 97.1%. The generalization of the proposed approach for achieving a cost-effective mill construction by reducing the total number of the required physical sensors will be the subject of our future research.

Background: Asthma is a widespread chronic respiratory disease that poses a significant public health challenge. The current study investigated the associations between air pollution and asthma severity among individuals residing near the Sohar industrial port (SIP) in Oman. Despite the presence of multiple major industrial complexes in Oman, limited knowledge regarding their impact on respiratory health is accredited. Hence, the primary objective of this study is to offer valuable insights into the respiratory health consequences of industrial air pollution in Al Batinah North. Methods: The state health clinics' records for patient visits related to asthma were collected for the timeframe spanning 2014 to 2022. Exposure was defined as the distance from SIP, Majan Industerial Area (MIA) and Sohar Industerial Zone (SIZ) to determine high, intermediate, and low exposure zones (12 km, respectively). Exposure effect modifications by age, gender, and smoking status were also examined. Results: The conducted cross-sectional study of 410 patients (46.1% males and 53.9% females) living in over 17 areas around SIP revealed that 73.2% of asthmatics were under 50 years old, with severity significantly associated with closeness to the port. Risk ratios were estimated to be (RR:2.42; CI95%: 1.01–5.78), (RR:1.91; CI95%: 1.01–3.6), and (RR:1.68; CI95%: 0.92–3.09) for SIP, MIP and SIZ areas, respectively, compared to the control area. Falaj Al Qabail (6.4 km) and Majees (6 km) had the highest number of asthma patients (N. 69 and N. 72), and highest percentages of severe asthma cases among these patients (28% and 24%) with significant risk ratios (RR:2.97; CI95%: 1.19–7.45 and RR:2.55; CI95%: 1.00–6.48), correspondingly. Moreover, severe asthma prevalence peaked in the 25-50 age group (RR:2.05; CI95%: 1.26–3.33), and this linkage between asthma and age was much more pronounced in males than females. Smoking and exposure to certain contaminant (dust and smoke) increased also the risk of severe asthma symptoms, but their effects were less important in the high risk zone, suggesting much more important risk factor. A neural network model accurately predicted asthma risk (94.8% accuracy), with proximity to Sohar Industrial Port as the most influential predictor. Conclusion: The study highlights the High asthma burden near Sohar Industrial Port, linked to port proximity and smoking and wind direction as major risk factors. These findings inform vital public health policies to reduce air pollution and improve respiratory health in the region, prompting national policy review.

Enhancement of mechanical properties by using TiN/TiCN/TiC multilayer thin films deposited on commercially pure cast Titanium (CP-Ti), Ti6Al4V and silicon (Si) substrates via magnetron sputtering technique was investigated in this study. The structural, chemical and mechanical properties of the coatings were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), nanoindentation and scratch test. Results of the XRD analysis showed reflections corresponded to FCC (1 1 1) cubic and polycrystalline structure for TiN/TiCN/TiC films. XPS analysis revealed formation of titanium nitride, titanium carbonitride and titanium carbide in the coatings. According to SEM images, the coatings demonstrated dense cross-sectional morphology and columnar structure as well as good adhesion to the substrate with a thickness of 1.77 μm deposited on silicon (1 0 0). Scratch and nanoindentation test results showed the best mechanical behavior for the coated Ti6Al4V substrate material with the 19.96 GPa hardness and 25 N critical load values, because of its higher hardness and toughness of substrate in compared to Cp-Ti substrate.

Enhancement of mechanical properties by using TiN/TiCN/TiC multilayer thin films deposited on commercially pure cast Titanium (CP-Ti), Ti6Al4V and silicon (Si) substrates via magnetron sputtering technique was investigated in this study. The structural, chemical and mechanical properties of the coatings were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), nanoindentation and scratch test. Results of the XRD analysis showed reflections corresponded to FCC (1 1 1) cubic and polycrystalline structure for TiN/TiCN/TiC films. XPS analysis revealed formation of titanium nitride, titanium carbonitride and titanium carbide in the coatings. According to SEM images, the coatings demonstrated dense cross-sectional morphology and columnar structure as well as good adhesion to the substrate with a thickness of 1.77 μm deposited on silicon (1 0 0). Scratch and nanoindentation test results showed the best mechanical behavior for the coated Ti6Al4V substrate material with the 19.96 GPa hardness and 25 N critical load values, because of its higher hardness and toughness of substrate in compared to Cp-Ti substrate.

The Sol Hamed (SH) area is a part of the Arabian-Nubian Shield (ANS) ophiolites occurred within Onib-Sol Hamed suture zone in the southern Eastern Desert of Egypt. The ophiolitic assemblages in this area are represented by serpentinite, metagabbro and arc assemblages represented by metavolcanics. They later intruded by gabbroes and granites. Geochemically, the compatible trace elements (Cr=2426–2709 ppm, Ni=1657–2377 ppm and Co=117–167 ppm) enrichment in SH serpentinites indicate derivation from a depleted mantle peridotite source. They show affinity to the typical metamorphic peridotites. The normative compositions reflect harzburgitic mantle source. Their Al2O3 contents (0.05–1.02 wt. %) are akin to oceanic and active margin peridotites and Pan-African serpentinites. The Cr and TiO2 contents indicate supra-subduction zone (SSZ) environment. Their Al2O3/SiO2 and MgO/SiO2 ratios support the SSZ affinity and are similar to ANS peridotites with fore-arc setting. Moreover, their Al2O3 and CaO depletion is typical of fore-arc peridotites. Structurally, the area represents four deformational events can be well-known in the Neoproterozoic rocks (D1, D2, D3 and D4); D1: E–W thrust faults and related E–W (F1) folds; D2: NW–SE thrust faults and related NW–SE (F2) folds were formed; D3: conjugate NNW-trending sinistral and NNE-trending dextral transpression, as well as N–trending tight folds (F3) and D4: is E–W dextral strike-slip and dip-slip normal faults striking NNW–SSE to N–S and E–W may be related to Red Sea rifting. There are major three fault sets affected the area. The first set trend mainly NE-SW and is manifested in the volcanic-sedimentary assemblage and Gabal SH and have important role in mineralization. The second set trend E-W affecting all the basement rocks and disturbs the first fault set. The third set trend N-S affected all the rock units. Magnesite mineralization in SH serpentinites is cryptocrystalline formed due to hydrothermal alteration of the serpentinite host rocks. It is occur as snow-white veins and stock-works. These characteristics are typical of Kraubath type magnesite deposits. Gold mineralization is confined to malachite-bearing quartz veins, smoky quartz veins and alteration zones. Malachite-bearing quartz veins trending NW-SE cut through gabbroic rocks and exhibit mylonitic structure. They are fractured containing malachite and disseminated sulfide minerals. Smoky quartz veins trending NE-SW with SE steeply dipping intrude the meta-andesite. They are intensively sheared containing iron oxides in the fissures. The gold grades increase with arsenopyrite occurrences. On the other hand, the barren quartz veins are nearly vertical with E-W directions. Alteration zones with NW-SE trend and nearly vertical dip intrude metagabbros and metavolcanics. Hematite, limonite, goethite and fresh pyrite characterize these zones. They occur mainly neighboring the auriferous quartz veins.

The rapid acceleration of artificial intelligence (AI) has sparked extensive debate about its impact on the safety and security of society. While AI has shown trans- formative potential, particularly in areas such as healthcare and independent structures where it complements productivity and minimizes human error, accu- racy and protection. However, the misuse of artificial intelligence poses real risks, along with threats such as deep counterfeiting, computer cyber-attacks and the manipulation of social behavior through disinformation. These risks vary from privacy and cyber security breaches to moral dilemmas around liability. The unchecked improvement of AI is expected to threaten the social order, so the relationship between innovation and governance is essential so that AI-related threats do not overshadow its benefits. This article offers a detailed assessment and review of the literature that studies the potential dangers that AI poses to society. The cumulative effects underscore the urgent need for comprehensive regulatory frameworks to mitigate these threats.

Winter frost injury is a major limiting factor for olive cultivation in temperate regions. The response of olive shoots to freezing stress can be used for selecting resistant genotypes to freezing. The electrolyte leakage (EL) and tetrazolium tests (TZ) are commonly used to evaluate dead tissues in cold stress studies. The temperature-response curve of dead tissues to lethal temperature (LT) is measured with models to calculate LT50 and LT90. In this study, we evaluated the accuracy and efficiency of eighteen non-linear regression models (NLRs) in calculating LT50 and LT90 of freezing stress in different olive cultivars at various stages of dormancy. After evaluating the prediction performance of NLR models, it was found that only eight models were suitable for the purpose of this research out of the 18 models examined. The 2p-logistic and Gompertz models were selected for modeling EL and TZ, respectively. Our research findings indicate that the Roughani, Kawi, and Zard varieties of olive trees exhibit the best performance in cold weather conditions. Our findings provide valuable insights into selecting frost-resistant cultivars and designing effective strategies for cold acclimation in olive cultivation.

Utilization of medicine derived from plants has been documented in various traditional systems of medicines throughout the world for different diseases. Therefore, the current research work was carried out to evaluate the phytochemical and biological potential of Ficus carica L ethanolic leaf extract. For this purpose, physicochemical and phytochemical analysis, total phenolic and flavonoids contents was performed. Antioxidant potential was determined by FRAP, DPPH and H2O2 assay. Proteinase inhibition, heat induced hemolysis and BSA denaturation assay was carried out for inflammation. Antiglycation potential was assessed by fructosamine assay, Congo-red assay and estimation of free carbonyl groups. In-vivo antidiabetic, anti-obesity, effect on liver and kidney were investigated by high fat high sugar diet model. FTIR, HPLC and LCMS/MS analysis was performed to find out the compounds. Tablet based formulation was developed using wet granulation method and tested for physicochemical parameters. Results shows that total phenolic and flavonoids content was (333 mg GAE/g) and (123 mg RE/g) respectively, H2O2 assay shows 35.6% free radical inhibition potential, DPPH assay shows (IC50) inhibitory concentration at 0.58 mg/mL, and 88.769 µg/g Fe2SO4 solution FRAP values. Proteinase inhibition assay, Heat induced hemolysis and BSA-denaturation assay shows percentage inhibition of 28 ± 0.01, 55 ± 0.03 and 51.2 ± 0.05 respectively. In Antiglycation activity β-amyloid formation assay shows absorption of 0.017, Fructosamine assay shows inhibition of 19.4±0.06 and free carbonyl group estimation shows inhibition of 17.0±0.03. In in-vivo study FLE at (500 mg/kg) significantly decreased total bilirubin (p ≤ 0.001), decreased (p ≤ 0.05) alanine transferase, aspartate aminotransferase, alkaline phosphatase, decreased blood glucose, triglycerides and total cholesterol (p ≤ 0.01) while HDL (p ≤ 0.01) was significantly increased in comparison to obesity and diabetic-obesity groups. Different functional groups presence was confirmed by FTIR spectrum. HPLC analysis revealed the existence of ferulic acid, rutin, chlorogenic acid, coumarin and thymoquinone and these results are corelated by LC-MS/MS. Pre-compression characterization showed angle of repose (33.04°), bulk density (0.54 g/cm3), tapped density (0.73 g/cm3), compressibility index (35.179 %) and Hausner’s ratio (1.35), while the post-compression characterization showed weight variation 826±4.17 mg, thickness 10.50±0.25 kg/cm2, friability 0.57 %, and disintegration time 8.19 min. From the above results it is concluded that F. carica L. leaves extract has strong antioxidant, antidiabetic and hypolipidemic potential and can be used for an obesity and diabetes treatment.

Calcium phosphates and manganese phosphates play a significant role in biomedical and engineering applications, and these compounds are both synergistic. These compounds could have great potential for use in different applications, particularly as precursors of biomaterials. Therefore, the aim of this study was to explore the effect of the gradual replacement of Ca2+ with Mn2+ on the phase composition and crystal structure of brushite (CaHPO4·2H2O), which could be useful for the production of Mono- and Biphasic Ca1−xMnxHPO4·nH2O Compounds. In order to prepare the starting solutions required for this study, Ca(NO3)2·4H2O, (NH4)2·HPO4, and Mn(NO3)2·4H2O were used at various molar concentrations. Afterwards, the Ca1−xMnxHPO4·nH2O compounds were prepared using dissolution and precipitation methods. These compounds were characterized using XRD, SEM, FT-IR, XPS, and TGA techniques. The findings revealed that Mn substituted Ca partially at low Mn/Ca molar ratios, 0.25, and Mn doping increased the unit cell of CaHPO4·2H2O. The produced biphasic compound was composed of monoclinic CaHPO4·2H2O and nanostructured orthorhombic MnHPO4·(H2O)3 after a continuous increase in the Mn/Ca molar ratio to 1.5. When the Ca/Mn molar ratio was above 1.5, a monophasic compound of the MnHPO4·(H2O)3 phase was formed. The MnHPO4·(H2O)3 compound was successfully prepared for the first time using this dissolution-precipitation method. It was also established that the Mn/Ca ratio of the starting solution can be modified to produce CaHPO4·2H2O and MnHPO4·(H2O)3 phases with specific weight percent compositions.

This paper investigates and explores the minor crops production in Pakistan and its association with the agricultural gross domestic product. The agriculture sector of Pakistan has a rich contribution to the economic growth and development. Like major crops; minor crops also have a vital role to boost up the agriculture sector. Time span data was used in this study and it was collected from the Economy Survey of Pakistan annual reports. Augmented Dickey-Fuller (ADF) unit root test and Ordinary Least Square (OLS) method was used to analyze the data and results were interpreted by employing the Johansen co-integration test. Study results reveal that bajra, barely and jowar has a significant impact on the agricultural gross domestic product, while the total cropped area has a negative impact on AGDP. On the basis of the study results, we recommend the policy implications.

When the minimal length approach emerging from noncommutative Heisenberg algebra, generalized uncertainty principle (GUP), and thereby integrating gravitational fields to this fundamental theory of quantum mechanics (QM) is thoughtfully extended to Einstein field equations, the possible deformation of the metric tensor could be suggested. This is a complementary term combining the effects of QM and general relativity (GR) and comprising noncommutative algebra together with maximal spacelike four–acceleration. This deformation compiles with GR as curvature in relativistic eight–dimensional spacetime tangent bundle, generalization of Riemannian spacetime, is the recipe applied to derive the deformed metric tensor. This dictates how the affine connection on Riemannian manifold is straightforwardly deformed. We have discussed the symmetric property of deformed metric tensor and affine connection. Also, we have evaluated the dependence of a parallel transported tangent vector on the spacelike four–acceleration given in units of L, where L = rℏcG3 is a universal constant, c is speed of light, and ℏ is Planck constant, and G is Newton’s gravitational constant.

The key question for the understanding of corrosion phenomena of Si3N4-SiC material in Al reduction cell – whether corrosion by gases (and oxidation in particular) opens way for the corrosion by molten cryolite, or corrosion of Si3N4-SiC by cryolite plays its own role in degradation of the material in service. More probably the reactions of silicon carbide and silicon nitride with molten cryolite go after the stage of pre oxidation to silicon dioxide. The corrosion of Si3N4-SiC material in the reduction cell may take place by “gas-solid” reaction and by “liquid-solid” reaction. There are several variants of lab corrosion test for the evaluation of corrosion resistance of Si3N4-SiC material to cryolite. The results of investigation of Si3N4-SiC lab corrosion test give no direct evidence of selective dissolution of specific phase (Si3N4 or SiC, α-Si3N4 or β-Si3N4) in cryolite. The existing variants of lab corrosion testing require clarification.

κ Draconis is a binary system with a classical Be star as the primary component. Its emission-line spectrum consists of hydrogen lines, notably the Hα line with a peak intensity ratio (V/R) variations phase-locked with the orbital period P = 61.55 days. Among binaries demonstrating the Be phenomenon, κ Dra stands out as one of a few systems with a discernible mass of its secondary component. Based on more than 200 spectra obtained in 2014 − 2023, we verified the physical parameters and constructed the mass function. We used part of these data obtained in 2014 − 2021 to investigate regions in the circumstellar disk of the primary component that emit the Hα line using the Doppler tomography method. The results show that the disk has a non-uniform density distribution with a prominent enhancement at Vy≈ 99 km s−1 and Vx≈−6 km s−1 that corresponds to a cloud-like source of the double-peaked Hα line profile. We argue that this enhancement’s motion is responsible for the periodic variations of the Hα V/R ratio, which is synchronised in orbital phase with the radial velocity (RV) of absorption lines from the atmosphere of the primary component.

Egyptians face a significant challenge in meeting the growing population's water needs for agriculture and food production. To address this, policymakers and researchers have implemented the National Great Project for Lining and Rehabilitation of All Open Canals of the Irrigation Network to reduce irrigation water losses through seepage, evaporation, and evapotranspiration. The current field study evaluates water losses from the Al Maanna canal network in Assiut governorate, Middle Egypt, using empirical formulas and field ponding methods. The obtained results indicated that the Moleth-Worth formula is more compatible and gives results that are in good agreement with the field measurements carried out. The estimated seepage losses from the existing, distorted Al Maanna canal network using the Moleth-Worth formula and field ponding method were about 2.07 and 2.20 million m3/month, respectively. Also, the calculated maximum evaporation and evapotranspiration losses were about 0.086 and 1.133 million m3/month, respectively. Consequently, the total water losses might be about 3.42 million m3/month, representing nearly 13.63% of the Al Maanna canal’s total discharge. After completing the lining process, seepage losses from lined canals were determined to be only about 0.472 million m3/month using the ponding method, while evaporation and evapotranspiration losses will be significantly decreased after canal rehabilitation. Hence, lining the Al Maanna canal network can decrease the total water losses by about 84%, which is sufficient to recommend and encourage the lining processes where the value of the gained quantities of water exceeds all the implementation expenses, in addition to other moral, cultural, and environmental gains.

Abstract: In recent years, the construction engineering sector has undergone a transformative shift towards the integration of machine learning (ML) techniques, particularly in predicting the properties of steel fiber-reinforced concrete (SFRC). Despite the theoretical sophistication of existing models, a persistent challenge remains – their opacity, lacking transparency and real-world relevance for practi-tioners. To address this gap and advance our current understanding, this study employs the extra gradient (XG) Boosting algorithm, crafting a comprehensive ap-proach. Grounded in a meticulously curated database drawn from 43 seminal pub-lications, encompassing 420 distinct records, this research focuses predominantly on three primary fiber types: crimped, hooked, and mil-cut. Complemented by hands-on experimentation involving 20 diverse SFRC mixtures, this empirical campaign is further illuminated through the strategic use of Partial Dependence Plots (PDPs), revealing intricate relationships between input parameters and con-sequent compressive strength. A pivotal revelation of this research lies in the identification of optimal SFRC formulations, offering tangible insights for real-world applications. The developed ML model stands out not only for its sophistication but also its tangible accuracy, evidenced by exemplary performance against inde-pendent datasets, boasting a commendable mean target-prediction ratio of 99%. To bridge the theory-practice gap, we introduce a user-friendly digital interface, thri-ughly designed to guide professionals in optimizing and accurately predicting the compressive strength of SFRC. This research thus contributes to the construction and civil engineering sectors by enhancing predictive capabilities and refining mix designs, fostering innovation, and addressing the evolving needs of the industry.

Silicon carbide particle-reinforced aluminum matrix (SiCp/Al) composites are significant lightweight metal matrix composites extensively utilized in precision instruments and aerospace sectors. Nevertheless, the inclusion of rigid SiC particles exacerbates tool wear in mechanical machining, resulting in a decline in the quality of surface finish. This work undertakes a comprehensive investigation into the problem of tool wear in SiCp/Al composite materials throughout the machining process. Initially, a comprehensive investigation was conducted to analyze the effects of cutting velocity vc, feed per tooth fz, milling depth ap, and milling width ae on tool wear during high-speed milling under SCCO2-MQL (Supercritical Carbon Dioxide Minimum Quantity Lubrication) ultrasonic vibration conditions. Furthermore, a prediction model for tool wear was developed by employing the orthogonal test method and multiple linear regression. The model's relevance and accuracy were confirmed using F-tests and t-tests. Ultimately, through the utilization of a genetic algorithm, the milling parameters were optimized, resulting in the identification of the most optimal combination of parameters. Empirical findings suggest that the careful selection of milling parameters can significantly mitigate tool wear, extend the lifespan of the tool, and enhance the quality of the surface. This work serves as a significant point of reference for the processing of SiCp/Al composite materials.

The detection and recognition of tables in image-based documents is a challenging and essential task for automated data extraction and anal- ysis. This paper introduces a methodology that utilizes Convolutional Neural Networks (CNNs) to address this problem. By harnessing the ro- bust visual recognition abilities of CNNs, the proposed method effectively detects and extracts tables from image-based documents. Additionally, an Encoder-Dual Decoder (EDD) architecture is employed to extract the textual content from table cells, enabling the transformation of visual data into structured, machine-readable formats. This structured data is then further processed using a Vector Space Model (VSM)-based language modeling technique for query-based table retrieval. The methodology’s accuracy is assessed by analyzing the spatial relationships between the extracted cells and comparing them against a pre-defined table structure. The results provide an evidence to the effectiveness of the proposed ap- proach, with an impressive 85% accuracy rate and a corresponding error rate of 15%. This accurate extraction and recognition of tables from image-based documents can significantly enhance applications in data analysis, information retrieval, and knowledge extraction.

The importance of Muscovy ducks in industrial poultry production is growing; however, little is known about the physiology of their reproductive cycles. This study investigated the influence of male biostimulation on female ducks before the commencement of the laying phase. A total of 15 female Muscovites were kept in contact with a male duck until the point of laying, while 15 other females were kept without any contact with a male conspecific. Before reaching egg-laying maturity, the cloacae of 29 adult ducks were subjected to daily clinical assessments. The evaluations yielded four unique categories of outcomes, determined by assessing factors such as the degree of redness and protrusion of the mucous membrane, moisture level, and swelling of the cloacal sphincter muscle. In terms of biostimulation, the findings demonstrated that, on average, ducks in contact with males laid the first egg 16 days earlier than isolated ducks. Furthermore, there was no significant difference observed in the mean initial egg weight between both groups (p = 0.841). The changes in the cloacal morphology indicated significant morphological changes 25–26 days before laying. Efforts to improve Muscovy production and develop biotechnological techniques to modify the reproductive cycle will benefit from these advancements.

The ability to predict the likelihood of a live birth after single fresh embryo transfer is important for treatment planning and managing patient expectation, particularly in their first in vitro fertilization (IVF) cycle. Cryopreservation of supernumerary embryos is often regarded as an important prognostic variable and a surrogate marker of success for several reasons. While previous large studies have examined the association between the number of oocytes retrieved and cleavage-stage embryos available, and the odds of a live birth following a fresh embryo transfer, the relationship between the number of supernumerary blastocysts cryopreserved following a fresh embryo transfer has not been rigorously studied. We performed a retrospective analysis of data collected between 2006 and 2018 for all first time IVF patients with a fresh autologous day 5 single blastocyst transfer. The relationship between the likelihood of a live birth and number of supernumerary blastocysts cryopreserved was assessed according to patient age group. In patients aged <35 years and 35-39 years old, the likelihood of a live birth increased linearly from 0.33 (95%CI:0.31–0.34) to 0.80 (95%CI:0.74–0.86; P<.0001) and 0.30 (95%CI:0.28–0.32) to 0.82 (95%CI:0.73–0.91;P<.0001) between 1-6 blastocysts cryopreserved and then non-linearly to 0.95 (95% CI 0.92–0.97; P<.0001) and 0.96 (95%CI:0.93–0.99; P<.0001) if 10 or more blastocysts were cryopreserved, respectively. When aged 40 years and above, the likelihood of a live birth increased linearly from 0.26 (95%CI:0.19–0.32) to 0.83 (95%CI:0.68–0.97; P<.0001) between 1-4 blastocysts cryopreserved and then non-linearly to 0.99 (95%CI:0.98–0.99; P<.0001) if 10 or more blastocysts were cryopreserved. The present study demonstrated a non-linear relationship between the number of supernumerary blastocysts cryopreserved and the likelihood of a live birth after single blastocyst transfer in the first autologous fresh IVF/ICSI cycle across different age groups.

At present there is a renewed interest in theories of ”modified” gravity. Here, under a more drastic modification enforced by Galilei group, we obtain a completely new gravitational structure, and which exists in addition to the already available general relativity of today. Correlated with this, we show that in addition, there is a new ”modified” quantum mechanics, in as much as it exists as an independent and new ”pure” non-relativistic quantum me- chanics, and which has no relativistic counterpart. This is in addition to the present quantum mechanics, where the relativistic and non-relativistic structures are counterparts of each other. The above holds, firstly due to the correlation between Galilei group and quantum mechanics. These math- ematical conclusions are consolidated by the fact that there exists a physical Majorana interaction between each neutron- proton pairs in nuclei. Galilei invariance of Majorana exchange in Majorana interaction, shows that the mass here is of pure gravitational nature, and which is immune to the other three forces. This makes an amazing connection between the gravitational force and the quantum mechanics. This pure gravitational mass would man- ifest itself as dark matter of the universe. It is our new modified gravity that generates the dark matter.

Background: Despite their generally favorable prognosis, hepatic fibrosis remains a possible complication for hepatitis B virus (HBV) inactive carriers. This study aimed to estimate the prevalence of significant fibrosis and associated risk factors among Omani HBV inactive carriers. Methods: A retrospective study was conducted of 200 Omani HBV inactive carriers visiting a tertiary hospital in Muscat, Oman, between January 2017 and December 2018. Significant fibrosis (stage F2 or higher) was identified using two-dimensional shear-wave elastography. Baseline clinical, laboratory, and radiological data were analyzed to determine associations. Results: Of the total sample, 106 patients (53%) were male, and the mean age was 44.6 ± 9.3 years. The prevalence of significant fibrosis was 20% (n = 40). Male gender (p = 0.007), age ≥60 years (p = 0.024), and fatty changes in liver ultrasound (p = 0.044) were found to be independent factors for significant fibrosis. Conclusion: the prevalence of significant fibrosis was relatively high among a sample of Omani HBV inactive carriers, with several sociodemographic and clinical risk factors identified. Periodic assessment of liver function is needed for patients with these risk factors; moreover, routine biochemical parameters could be useful predictors of disease prognosis. Further research is recommended to substantiate these findings.

This research investigates the impact of Al and Ti elements on the formation of self-generated ordered phase in high-entropy alloys (HEA), which have been receiving widespread concentration in present times thanks to their remarkable multifunctional properties and wide range of component selection. By adjusting the dual elements of Al and Ti, the study explores the regulation of quantity and distribution of the in-situ self-generated ordered phases in the alloy. The results of the annealing heat treatment process demonstrated that, through accession Al and Ti elements, the Cr-Fe-Ni medium-entropy alloy transfer from BCC phase to BCC+FCC phase and the precipitation of new phases such as B2, L21, and σ. This led to a synergistic impact of second phase strengthening, and also of solid solution strengthening, resulting in improved compressive properties of HEA.

The research presented in the article is devoted to the study of the influence of phase compounds on the friability of the Fe-Si-Mn-Al complex alloy. The urgency of the problem lies in the development of technology for producing a non-scatterable alloy from manganese-containing ores and high-ash coals. The main goal of the work is to determine the range of alloy compositions and the resulting phases that affect the dispersibility of the alloy, which is critically important for its industrial implementation. Research methods include thermodynamic diagram analysis (TDA) using data on the standard enthalpy of formation of intermetallic compounds, as well as experimental tests in an ore-thermal electric furnace with a capacity of 200 kV*A. The results show that Fe-Si-Mn-Al complex alloys form a variety of silicide and aluminide phases, including intermetallic compounds and ternary systems, which is critical for understanding and controlling their physicochemical properties. When smelting a complex alloy, the content of leboite (Fe3Si7) in the Fe-Si-Mn-Al system plays a significant role. The development of smelting technology will be aimed at avoiding the FeSi2-Fe3Si7-F2(FeAl3Si2)-Mn11Si19 tetrahedron area. This approach to controlling the composition of a complex alloy is critical to ensuring its consistent friability properties in industrial applications. Thus, this work represents an important step in understanding the physical properties and stability of Fe-Si-Mn-Al complex alloys, which have potential for widespread use in metallurgical and other industrial applications.

Nowadays recurrent implantation failure (RIF) after invitro fertilization is common problem that reproductive specialists usually faced. The phenomenon of thin endometrium in RIF patients has yet not completely understood and properly treated. This study aimed to reveal significantly dysregulated selected genes expression between RIF patients with thin endometrium and fertile women. Endometrial samples were collected in the implantation window days (LH+7 – LH+10) of the natural menstrual cycle from RIF patients (n=20) and fertile women (n=14). Ten genes were chosen as target genes regarding their possible relations with the implantation process. Endometrial gene expression levels showed differences in RIF samples compared to fertile samples. The significant downregulation was observed for CXCL1 (p=0.005) and C4BPA (p=0.03) genes. There was no statistically significant difference between the RIF groups and the fertile group in the expression of 8 genes: CXCL8, HPRT1, MMP10, INFG, VEGFB, HAND2, IL15 and TNC (p&gt;0.05). The use of a combination of two markers (C4BPA + CXCL1) allows for good discrimination of RIF patients from fertile women (AUC 0.806).

Recently several papers have been published on the Liénard equation x'' +L x+m x^3+n x^5=0, where the authors studied their explicit solutions and their applications. Here we describe the complete dynamics of these differential equations in the Poincar\'e disc. The Poincar\'e disc is the closed disc centered at the origin of coordinates of radius one, the whole plane R^2 is identified with the interior of this disc, and its boundary, the circle $\sss^1$ is identified with the infinity of R^2.

This study aimed to investigate the fatigue performance and interfacial strengthening mechanisms of Al6061-to-Cu dissimilar lap joints via electromagnetic pulse welding (EMPW). The load-bearing capacity of the joints at discharge voltages of 14 kV and 16 kV was superior to that of 12 kV. Furthermore, the fatigue life of the 14 kV joints was one order of magnitude higher compared to the 12 kV joints. SEM observation of the fatigue fracture surface revealed the presence of typical "tire-mark" fatigue striations only in the 14 kV joint, indicating higher ductility and the ability to withstand extended plastic deformation. Notably, ultra-fine nanocrystalline Al2Cu phase, amorphous phase, and numerous dislocations hindered EBSD acquisition in the transition zone. Nevertheless, dense low-angle grain boundaries (LAGBs) and refined grains were examined at the bonding interface. This suggests that the high-velocity collision caused severe plastic deformation and led to the formation of substructures. The interfacial strength was attributed not only to the "wave-like" or "inverted hook-like" diffusion layer but also to the presence of refined grains along the interface and nanocrystalline Al2Cu in the transition zone. Furthermore, the hybrid nanocrystalline-amorphous microstructure strengthened the joint by regulating the balance between strength and ductility.

In the era of mounting water scarcity, particularly in arid regions, the agricultural sector is striving to optimize the water resource management practices. Treated wastewater (TWW) has emerged as a viable alternative to freshwater for irrigation, offering a sustainable solution to water conservation. However, ensuring the safety and quality of TWW is paramount to safeguard for both crop health and environmental integrity. Electrical conductivity (EC), a critical factor in assessing TWW suitability for irrigation, can significantly impact crop yields and soil health since it is directly linked to the concentration of dissolved salts and ions. Therefore, this study delves into the development of advanced predictive models for EC assessment by employing supervised machine learning (ML) techniques like the Support Vector Regression (SVR), Adaptive Network-based Fuzzy Inference System (ANFIS), and Multiple Linear Regression (MLR). The TWW samples collected from Al-Qatif area, Saudi Arabia were assessed in the lab through a sensor-based real-time monitoring system integrated with Internet of Things (IoT) network and a multiprobe device. The key water quality parameters assessed involved, temperature (T), pH, Oxidation Reduction Potential (ORP), Resistivity (RES), Total Dissolved Solids (TDS), Salinity and Turbidity which served as the foundation for these models, given their profound influence on and their anticipated impact on EC levels. Following feature selection, two distinct model combinations were identified for the SVR, ANFIS and MLR models. Furthermore, to evaluate prediction performance, four statistical criteria, including coefficient of determination (R²), correlation coefficient (R), mean square error (MSE), and root mean square error (RMSE), were employed. Overall, the comparative performance results proved that ANFIS-M2 indicated the strongest predictive capability with the R² value of 0.99572 and 0.75145 and the RMSE values of 0.00965 and 0.01134, respectively in both calibration and verification stages.

This paper investigates the influence of magnetic field for a two dimensional deformations on a two temperature problem at the free surface of a semi-infinite semiconducting medium under the effect of mechanical force during a photothermal theory and the effect of hydrostatic initial stress on the medium. The Harmonic Wave Method (Normal Mode Analysis) has been used to obtain the equations of elastic waves, heat conduction equation, quasi-static electric field, carrier density, two temperature coefficient, ratios, and constitutive relationships for the thermo-magnetic-electric medium. The effects of several parameters as thermoelastic and thermoelectric coupling parameters and two temperature parameter of this force on the displacement component, force stress, carrier density and temperature distribution has been depicted graphically.

A new class of nano-cube core-shell heterostructures containing Ag coating on the top of WO₃ was fabricated. Physical vapor deposition was used to produce WO₃ based nano-heterostructures. All kind of wet toxic chemical process was avoided to make the process simple and contaminant free. Sputtering of WO₃ and a subsequent thermal annealing process was done to create nano-cubes of WO₃. After that, sputtering of Ag was performed to form the Ag-WO₃ core-shell nano-heterostructures (CSNH). The CSNHs were characterized using field emission scanning electron microscopy (FESEM), energy dispersive spectroscopy (EDS), X-ray diffraction analysis (XRD) and UV-vis spectroscopy. The morphologies, elemental analysis, interfaces, crystallinity, phases, and chemical compositions were analyzed. The bottom-up growth of WO₃ nanocubes was studied using different time periods at 900°C. Ag coating was also studied before and after annealing. Finally, an optical property (band gap) was also analyzed using Tauc plot derive from absorption spectra. The tailoring the band gap of WO₃ from ~2.9eV to ~ 2.45 eV was observed while Ag-WO₃ CSNH formed.

General phytochemical screening of the aerial parts of Consolida orientalis revealed the presence of steroids, terpenes, phenolic compounds, saponins, fatty acids, alkaloids. This study was conducted to investigate the bioactivities of extracts, isolation and identification the compounds from aerial parts of C.orientalis. The main goal of the present study is identifying and characterizing the antioxidant activity of the Consolida orientalis and biological isolation of active terpenoid. Aerial parts of the plant were dried at room temperature and reduced to small pieces, followed by using extraction with ethyl acetate percolation. Tree complementary analysis system was used, DPPH free radical scavenging test, total phenolic metabolites and FRAP. The total phenolic content was 38.83±2.09 mg gallic acid corresponding to g-1 extract with regarding to standard curve (y=0.0054x+0.0488, r2=0.995). IC50 value for DPPH radical – scavenging was 987.11±28.66 mgml-1. The extract was exhibited a medium reducing power compared with Vit C. The isolation and purification was afforded white crystalline powder which was subjected to physical, chemical and spectral identification by IR, ¹H- and ¹³C- NMR and GC-MS. Isolated compound was identified as β-sitosterol. That is a terpenoid with melting point 133.4-134.5 ͦ c and with molecular formula C₂₉H₅₀O.

Transcranial magnetic stimulation, TMS, has been an innovative method of demure neuromodulation. This paper aims to delve into the different forms of its existence and to evaluate the use of TMS in five psychiatric disorders; Parkinson’s disease, schizophrenia, obsessive-compulsive disorder, major depressive disorder, and major anxiety disorder. Literature pertaining to the use of TMS in treating these specific diseases will be analyzed, and its efficacy and mechanisms will be explored. The literature will be evaluated through sources with established facts and research studies demonstrating function, potency, or inefficacy. TMS poses a method to have a more explicit effect on the regions of the brain, and the exploration of its use in the treatment of psychiatric diseases poses new possibilities in the treatment of psychiatric disorders. Venturing into the options it could have in a sole or combinatorial setting could provide penetrating insight into innovative forms of treatment and research.

Reproductive disorders are a common event in modern reproductive medicine, occurring both in spontaneous and assisted pregnancies. Studies of the molecular mechanisms of implantation disorders in thin endometrium, including the study of gene transcriptional activity, have shed light on the identification of potential biological markers of endometrial receptivity. Background/Objectives: to reveal significantly dysregulated selected genes expression between RIF and RPL patients with thin endometrium. Methods: Endometrial samples were collected in the implantation window days (LH+7 – LH+10) of the natural menstrual cycle from RIF patients (n=20) and RPL patients (n=19). Ten genes were chosen as target genes regarding their possible relations with the implantation process. Total RNA was purified, reverse-transcribed; gene expression was quantified by RT-PCR. Results: The expression of the IL-15, INFG and HPRT1 genes were significantly decreased in RIF with thin endometrium patients compared to the RPL patients (log2 fold change=0.92, p=0.023 for IL-15, log2 fold change=1.24, p=0.046 for INFG, and log2 fold change=0.579, p=0.046 for HPRT1). There were not significant differences in expression of CXCL8, CXCL1, MMP10, C4BPA, TNC, VEGFB and HAND2 genes between groups. Conclusions: decreased expression of IL-15, INFG and HPRT1 genes was found in patients with RIF with thin endometrium compared to the endometrium of women with RPL. This has practical significance for clinicians for differentiated prescription of immunomodulatory therapy in patients undergoing ART programs.

In this paper, we proposed a new model of non-linear electrodynamics with parameter. Firstly, we study the weak limit approximation and by using the Gauss Bonnet theorem, we obtain the deflection angle of photon from magnetized black hole and effect of bnon-linear electrodynamics. In doing so, we find the corresponding optical metric after that we calculate the Gaussian curvature which is used in Gauss Bonnet theorem. Then we show the deflection angle in the leading order terms. We also analyzed that our results reduces into Maxwell's electrodynamics and RN solution with the reduction of parameters. Moreover, we also investigate the graphical behavior of deflection angle w.r.t correction parameter, black hole charge and impact parameter.

This study aims to formulate binary cementitious systems containing silica fume (SF) and micro quartz (MQ) to improve cementitious concrete's durability and mechanical properties. In this investigation, we examined the effects of different essential variables, such as the level of SF and MQ replacement and the ratio of the water-binder (w/b). In this study, the w/b ratios were 0.25, 0.3, 0.35, and 0.4. Replacement levels for SF were 8, 10, and 12%, while replacement levels for MQ were 5, 8, 10, 15, 25, and 35%. The porosity and permeability decreased with an increase in replacement levels, regardless of the type of fine material used or the amount of replacement. Meanwhile, the strength increased markedly with SF replacement, reaching its maximum MQ of 25% at the SF level. The strength of the SF mixing was the highest in all mixes, and it remained the highest until 15% of MQ was replaced. The ultrafine size of MQ particles contributes to the improvement of compressive strength, porosity, and permeability in a similar way to SF particles, despite their high crystalline structure. Furthermore, in this study, analysis of variance (ANOVA) was employed to verify the influence of each variable on the studied response.

Orodispersible film (ODF) is one of the novel formulations that have been currently made available that disintegrates rapidly in the mouth without the requisite for water and offer several benefits over conventional oral solid dosage formulations. This delivery system serves as a discreet and convenient mode of administration, especially in patients who have dysphagia, fluid restriction, being beneficial to pediatric, geriatric, and bedridden patients. A novel sildenafil ODF containing sildenafil citrate is formulated to be used in patients with erectile dysfunction (ED). This review discusses the advantages of ODF in improving compliance and satisfaction in these patients and describes the bioequivalence and stability studies of sildenafil ODF. This formulation offers unique benefit to patients with ED by improving their acceptance, compliance, and respecting their privacy. Moreover, the comparison of pharmacokinetic parameters between the sildenafil ODF administered with and without water and the conventional film-coated tablet were similar. It also demonstrated reliable performance that yielded a consistent product, meeting all specifications at release and after three weeks of storage under stressed conditions (60oC). Sildenafil ODF warrants improved ease of intake, taste, portability, storage, and compliance among ED patients, making it the potential most preferred formulation and drug of choice.

Gestational trophoblastic diseases (GTDs) encompass a spectrum of conditions characterized by abnormal trophoblastic cell growth, ranging from benign molar pregnancies to malignant trophoblastic neoplasms. This systematic review explores the molecular underpinnings of GTDs, focusing on genetic and epigenetic factors that influence disease progression and clinical outcomes. Based on 65 studies identified through systematic search and selection criteria, key findings include dysregulations in tumor suppressor genes such as p53, aberrant apoptotic pathways involving BCL-2, and altered expression of growth factor receptors and microRNAs. These molecular alterations not only differentiate molar pregnancies from normal placental development but also contribute to their clinical behavior, from benign moles to potentially malignant forms. The review synthesizes insights from immunohistochemical studies and molecular analyses to provide a comprehensive understanding of GTD pathogenesis and implications for personalized care strategies.

Salmonella Typhimurium is a typical Gram-Negative bacterium associated with food-borne illness threatening public health. This pathogen is reported to have caused millions of infections and thousands of hospitalizations yearly in the United States alone. Salmonella Typhimurium has a sophisticated array of virulent factors, including its flagella, which contributes significantly to its pathogenicity. Cannabidiol (CBD), the non-psychoactive component of the cannabis plant, has attracted the interest of many researchers recently because of its antimicrobial properties. With the growing interest in exploring CBD’s antimicrobial properties, we, in this study, have delved into unravelling how prolonged exposure of Salmonella Typhimurium to CBD influences the expression of the flgA gene. We hypothesized that the exposure of Salmonella Typhimurium to CBD may result in flgA upregulation, causing the bacteria to withstand various stresses and potentially enhance its survival rates and pathogenicity. We have employed several assays, such as mRNA expression, motility assays, pH induction assays, nutrient starvation interventions, and biofilm analysis, to explore the influence of CBD on the pathophysiology of Salmonella Typhimurium. Our findings reveal that CBD-resistant strains exhibit enhanced resilience to extreme pH levels and motility and survive poorly under nutrient starvation, with more robust biofilm formation compared to the susceptible strains. The results contribute to the broader comprehension of CBD resistance mechanisms in bacteria. This work provides insight into the potential therapeutic interventions for controlling CBD-resistant bacterial infections. This study also underscores the essence of exploring novel alternative antimicrobial agents to tackle the ever-persistence of bacterial antibiotic resistance.

Cloud computing has revolutionized how industries store, process, and access data. However, the increasing adoption of cloud technology has also raised concerns regarding data security. Machine learning (ML) is a promising technique to enhance cloud computing security. This paper focuses on utilizing ML techniques (Support Vector Machine, XGBoost, and Artificial Neural Networks) to progress cloud computing security in the industry. The selection of 11 important features for the ML study satisfies the study's objectives. This study focused on identifying gaps in utilizing ML techniques in cloud cyber security. Moreover. this study aims at developing a practical strategy for predicting the employment of machine learning in an Industrial Cloud environment regarding trust and privacy issues. The efficiency of the employed models is assessed by applying validation matrices of Precision, Accuracy, Recall values, F1 score, R.O.C. curves, and Confusion matrix. The results demonstrated that the X.G.B. model outperformed in terms of all the matrices with an Accuracy of 97.50 %, 97.60 % Precision, 97.60 % Recall values, and 97.50 % F1 score. This research highlights the potential of ML algorithms in enhancing cloud computing security for industries. It emphasizes the need for continued research and development to create more advanced and efficient security solutions for cloud computing.

Rat is one of the most commonly used model animals for biological research. The organs and systems of human being are somewhat similar to that of rat in structure as well as functions, making it a valuable choice for research experimentation in biological sciences. A number of studies have been conducted to evaluate the potential risks and toxicity of different elements on the physiology and histology of rats. There is need to address certain environmental factors affecting rats condition during experimentation. Reproduction along with its pathologies is under investigation on larger scale throughout the world, being central for the existence of a species. These studies focus on the major factors that influence reproductive function. Review of literature clearly indicated the unwanted consequences of over nutrition, malnutrition, high or low temperature, non-enriched housing, improper handling, intense or poor light exposure and environmental pollution on histology and hormonal profile of reproductive system of rats.

In this study, the prevalent methodology for design of the industrial policy in developing countries was critically assessed, and it was shown that the mechanism and content of classical method is fundamentally contradictory to the goals and components of the endogenous growth theories. This study, by proposing a new approach, along settling Schumpeter's economic growth theory as a policy framework, designed the process of entering, analyzing and processing data as the mechanism of the industrial policy in order to provide "theoretical consistency" and "technical and Statistical requirements" for targeting the growth stimulant factor effectively.

This study presents the design and implementation of a piezoelectric power harvesting device to capture vibrational strength from pipelines to autonomous strength IoT devices. The gadget utilizes key components along with the PPA-1001 piezoelectric sensor, STM32F103C8T6 microcontroller, and LTC-3588 energy harvesting strength delivery. Experimental results verified the gadget's performance in harvesting strength within a specific frequency variety of 10 Hz to 50 Hz, with the foremost overall performance at 30 Hz. The device generated the highest voltage of 3.3V, delivering a strength output of 2.18 mW, which is sufficient to power low-strength electronic gadgets. The device maintained solid performance across a temperature range of 20°C to 35°C, underscoring its robustness in various environmental situations. The findings highlight the capacity of this generation to offer a sustainable power source for far-off pipeline tracking, contributing to stronger protection and operational efficiency.

The endocannabinoid system (ECS) is a complex neuromodulatory network in the human body that have enormous impact in developing the central nervous system, as well as modulates various physiological processes. The ECS is made up of anandamide, 2-arachidonoylglycerol (2-AG), which are responsible for the synthesis and degradation of endocannabinoids, and enzymes such as FAAH and MAGL ensures the precise control over endocannabinoid levels. The ECS relies on CB1 receptors found in the central nervous system (CNS), and CB2 receptors found in the peripheral nervous system and immune cells. Dysregulation of the ECS has been associated with several health conditions, prompting investigations into its association with phytocannabinoids to harness their therapeutic potential. The ECS is intricately linked with the nervous system, and it is known to modulate neuronal activities in the CNS, influencing pain and mood modulation. The ECS is also associated with neuropathies-peripheral nerve damage leading to symptoms such as weakness, numbness and pain as evidenced in diabetic neuropathy, Guillain-Barré Syndrome, carpal tunnel syndrome, peripheral neuropathy, and postherpetic neuralgia. The focus of this review is on the interplay between 2-arachidonoylglycerol and anandamide amidohydrolase in neuropathy, elucidating their roles in pain regulation, inflammation, and specific neuropathies. The knowledge generated is expected to have broad implications, providing comprehensive insights into neuropathic conditions and how to improve on them. Ultimately, this understanding may lead to more effective treatments and improved quality of life for individuals affected by these conditions.

Deep neural networks (DNNs) have made a huge impact in the field of machine learning by providing unbeatable humanlike performance to solve real-world problems such as image processing and natural language processing (NLP). Convolutional neural network (CNN) and recurrent neural network (RNN) are two typical architectures that are widely used to solve such problems. Time sequence-dependent problems are generally very challenging, and RNN architectures have made an enormous improvement in a wide range of machine learning problems with sequential input involved. In this paper, different types of RNN architectures are compared. Special focus is put on two well-known gated-RNN’s Long Term Short Memory (LSTM) and Gated Recurrent Unit (GRU). We evaluated these models on the task of force estimation system in pouring. In this study, four different models including multi-layers LSTM, multi-layers GRU, single-layer LSTM and single-layer GRU) were created and trained. The result suggests that multi-layer GRU outperformed other three models.

From the hospital wastewater, a novel bacteriophage was isolated and characterized. According to characterization properties, this bacteriophage belongs to the Siphoviridae family, the maximum bacteriophage titer was recorded at 37°C and a pH of 7.2, had a 44,789 bp linear double-strand DNA genome, and within the genome sequence, there are 61 genes, all of which are encoded into proteins. Although this bacteriophage does not have any virulence factors or antimicrobial resistance genes and had specific lytic activity against some antimicrobial resistance S. aureus clinical isolates.

Increasing efforts have been devoted to promoting sustainable demolition waste management (DWM) from a life cycle-thinking perspective. To this end, facilitating sustainability-oriented de-cision-making for DWM planning requires a sustainability assessment framework for assessing multifaceted criteria. This study develops a BIM-based DWM sustainability assessment ap-proach to facilitate the life cycle assessment (LCA) and decision-making by coupling the enriched IFC model with hybrid Multi-Criteria Decision-Aiding (MCDA) methods using Dynamo visual scripting. To streamline the data-intensive LCA process, this study enriched the BIM properties and accommodated them into the LCA data template to enhance data interoperability, thus achieving seamless data transfer. Moreover, hybrid MCDA methods are integrated into the deci-sion-making workflow for DWM scenario ranking. A pilot study is employed to verify the ap-plicability of the decision-aiding framework. The results unveil that the sustainability score ascended with the recycling rate. The optimal DWM alternative with the highest recycling rate yields the highest sustainability score at 91.63. Conversely, a DWM alternative reflecting the ‘status quo’ in China’s recycling industry has the lowest score at 8.37, significantly lower than the baseline scenario with a 50% recycling rate. It is worth noting that the ‘growth curve’ of the sustainability score continuously flattens as the target recycling rate escalates. The increment in recycling rate from the “Australian standard” scenario to the optimal scenario is 18.4%, while the sustainability score merely increases by 2.3%, signal-ling that the former scenario arrived at an optimum point for maximising the cost-efficiency of DWM under the predefined framework and contexts.

Dietary intake of Wistar rats of biofortified with 8-hydroxy-7-iodo-5-quinolinesulfonic acid (8-OH-7-I-5QSA) kale of both cultivars ‘Oldenbor F1’ and ‘Redbor F1’ for 8 weeks resulted in sig-nificantly higher iodine concentrations in the urine and kidneys of rats, which proves iodine bio-availability. Rats diets with 'Oldenbor F1' and 'Redbor F1' kale non- and -biofortified with 8-OH-7-I-5QSA had a significantly lower or a tendency for lower concentration of TSH, triglyc-eride, total and direct bilirubin, TBARs, uric acid, aspartate aminotransferase (AST) and alanine aminotransferase (ALT) concentrations in serum. Dietary intake of 'Oldenbor F1' and 'Redbor F1' kale biofortified with 8-OH-7-I-5QSA significantly increased the total antioxidant status (TAS). The study confirms that kale biofortified with iodine in organic form iodoquinoline 8-OH-7-I-5QSA is bioavailable and well absorbed by the Wistar rat and has a positive effect on selected biochemical parameters.

The aim of this study is to study the effect of aging in different media (deionized water and artificial saliva) on the force/torque generation by thermoplastic orthodontic aligners. Ten thermoformed aligners made of Essix ACE® thermoplastic sheets were aged in deionized water and in artificial saliva over two weeks at 37 C, five in each medium. The force/torque generated on upper second premolar (Tooth 25) of a resin model was measured at day 0 (before aging), 2, 4, 6, 10, and 14, using a biomechanical test set-up. The results showed that the thermocycling of aligners has no significant impact on their force/torque decay. No significant differences were also found in force/torque between the aligners stored in deionized water nor artificial saliva. The vertical extrusion-intrusion forces were measured in the range of 1.4 to 4.6 N, the horizontal oro-vestibular forces were 1.3 to 2.5 N, while the torques on mesio-distal rotation were 5.4 to 41.7 Nmm. It could be concluded that the influence of saliva on the mechanical properties can be classified as insignificant, and no significant difference between artificial aging in deionized water or artificial saliva was observed.

Since the beginning, humans advanced their civilization by making better tools to improve their lives. Tools and products were designed for better living considering manufacturing issues, cost and time as predominant criteria. It has become clear that not considering environment and society, both at local/global levels, has now become a major impediment affecting living conditions on a large portion of the Earth and in many societies. Design methodologies should lead to creative solutions with consideration to engineering and economics for practicality but also to environmental and social constraints for sustainability. We propose a comprehensive design methodology based on multidisciplinary design to include the knowledge of humanities, environmentalists, science and engineering, and allowing for experts’ inputs from these areas to provide a holistic approach to engineering design . For example, experts in humanities are expected to interact with stakeholders to evaluate their value systems to provide guidance for the design. The methodology that we synthesize is new and combines (i) Societal level impacts at all scales, (ii) Environmental impacts and (iii) Engineering design with economic impacts, including uncertainty considerations. The proposed design methodology is called Social-Environmental-Economical-Engineering Framework (SEEEF). It can utilize concepts and tools such as Circular Design, Doughnut Economics, design based on environmental life cycle analysis, among others. SEEEF is quantity based and provides steps for evaluating any project or product in an objective manner and will help train engineers in design for sustainability. It also provides non-engineers with a significant role in design to increase their understanding of the hard constraints of engineering. Ultimately, SEEEF allows society to take an informed decision considering short/long term and local/global impacts of the design and the pertinent uncertainties.