The aim of the study was to determine the occurrence and characteristics of coagulase-positive Staphylococcus strains in the carcasses of wild birds and aviary capercaillies in south-eastern Poland. Samples from capercaillies and wild birds belonging to 12 orders and 26 species were tested. The resistance of the strains and the presence of selected virulence genes were examined. Similarity analysis of the isolates was performed using pulsed-field gel electrophoresis (PFGE). Coagulase-positive Staphylococcus strains accounted for 5.7% and belonged to the species: Staphylococcus aureus, Staphylococcus pseudintermedius and Staphylococcus delphini. Among isolated strains, 15.8% were multidrug resistant. The most frequently detected virulence genes were hla in 58% of isolates and hlb and hld in 47.4% of isolates., The results of multiplex PCR showed the presence of genes responsible for the production of enterotoxins C, B, E, and J, in single isolates. It can be concluded that coagulase-positive Staphylococcus strains accounted for a small percentage of staphylococci isolated from free-living birds in the study area. The occurrence of multidrug-resistant coagulase-positive Staphylococcus strains in aviary capercaillies suggests that they play a role in the transmission and spread of resistant strains into the environment. Free-living birds may be also a significant reservoir of enterotoxigenic Staphylococcus strains.

Nutrient depletion in Tanzanian sisal production has led to yield decreases over time. We use nutrient mass balances embedded within a life cycle assessment to quantify the extent of nutrient depletion for different production systems, then used circular economy principles to identify potential cosubstrates from within the Tanzanian economy to anaerobically digest with sisal wastes. The biogas produced is then used to generate bioelectricity and the digestate residual can be used as a fertilizer to address the nutrient depletion. If no current beneficial use of the cosubstrate was assumed, then beef manure and marine fish processing waste were the best cosubstrates. If agricultural wastes were assumed to have a current beneficial use as fertilizer, then marine fish processing waste and human urine were the best cosubstrates. The largest reduction in environmental impacts resulted from bioelectricity replacing electricity from fossil fuels in the national electricity grid and improved onsite waste management practices. There is significant potential to revitalize Tanzanian sisal production by applying circular economy principles to sisal waste management and bioenergy production.

The article presents a non-destructive test system based on electrical impedance tomography for monitoring flood embankments. The technology of cyber-physical systems and the Internet of Things with the use of electrical impedance tomography enables real-time monitoring of flood embankments. This solution provides a visual analysis of damage and leaks, which allows for quick and effective intervention and possible prevention of danger. A dedicated solution based on the IT structure, dedicated laboratory models and a dedicated measurement system with various types of sensors and machine learning algorithms for image reconstruction has been developed. The system includes specialized intelligent devices for tomographic measurements. The application contains the analysis of anomalies occurring in the structure of the object as a result of damage or danger and breaking the shaft during the flood. The presented solution enables ongoing monitoring of objects by collecting measurement results, forecasts and simulations. The main advantage of the proposed system is the spatial ability to analyse shafts, high accuracy of imaging and high speed of data processing. The use of tomographic techniques in conjunction with image reconstruction algorithms allow for non-invasive and very accurate spatial assessment of humidity and damages of flood embankments. The presented results show the effectiveness of the presented research.

The article presents the results of research on a new method of spatial analysis of walls and buildings moisture. Due to the fact that destructive methods are not suitable for historical buildings of great architectural significance, a non-destructive method based on electrical tomography has been adopted. A hybrid tomograph with special sensors was developed for the measurements. This device enables the acquisition of data, which are then reconstructed by appropriately developed methods enabling spatial analysis of wet buildings. Special electrodes that ensure good contact with the surface of porous building materials such as bricks and cement were introduced. During the research, a group of algorithms enabling supervised machine learning was analyzed. They have been used in the process of converting input electrical values into conductance depicted by the output image pixels. The conductance values of individual pixels of the output vector made it possible to obtain images of the interior of building walls, both flat intersections (2D) and spatial (3D) images. The presented group of algorithms has a high application value. The main advantages of the new methods are: high accuracy of imaging, low costs, high processing speed, ease of application to walls of various thickness and irregular surface. By comparing the results of tomographic reconstructions, the most efficient algorithms were identified.

Corrugated cardboard is an ecological material, mainly because, in addition to virgin cellulose fibers also the fibers recovered during recycling process are used in its production. However, the use of recycled fibers causes slight deterioration of the mechanical properties of the corrugated board. In addition, converting processes such as printing, die-cutting, lamination, etc. cause micro-damage in the corrugated cardboard layers. In this work, the focus is precisely on the crushing of corrugated cardboard. A series of laboratory experiments were conducted, in which the different types of single-walled corrugated cardboards were pressed in a fully controlled manner to check the impact of the crush on the basic material parameters. The amount of crushing (with a precision of 10 micrometers) was controlled by a precise FEMat device, for crushing the corrugated board in the range from 10 to 70 % of its original thickness. In this study, the influence of crushing on bending, twisting and shear stiffness as well as a residual thickness and edge crush resistance of corrugated board was investigated. Then, a procedure based on a numerical homogenization, taking into account a partial delamination in the corrugated layers to determine the degraded material stiffness was proposed. Finally, using the empirical-numerical method, a simplified calculation model of corrugated cardboard was derived, which satisfactorily reflects the experimental results.

As long as the non-contact digital printing is not a common standard in the corrugated packaging industry, corrugated board crushing is a real issue that affects the load capacity of the boxes. Crushing mainly occurs during the converting of corrugated board (e.g. analog flexographic printing or laminating) and is a process that cannot be avoided. However, as show in this study, it can be controlled. In this work, extended laboratory tests were carried out on the crushing of double-walled corrugated board. The influence of fully controlled crushing (with a precision: ±10 μm) in the range from 10 to 70 % on different laboratory measurements was checked. Most of the typical mechanical tests were performed e.g. edge crush test, four-point bending test, shear stiffness test, torsional stiffness test, etc. on reference and crushed specimens. The residual thickness reduction of the crushed samples was also controlled. All empirical observations and performed measurements were the basis for building an analytical model of crushed corrugated board. The proven and verified model was then used to study the crushing effect of the selected corrugated board on the efficiency of simple packages with various dimensions.

Paper is a material whose mechanical properties are highly dependent on humidity and temperature. Which naturally also builds the relationship between the stiffness and strength of corrugated board and changing weather conditions. In this paper, attention is focused on the dependence of the physical properties of the cardboard on changes in humidity and temperature, which undergo dynamic fluctuations both during the production of corrugated board and during its storage. Two techniques were used to test this effect, namely numerical homogenization and global sensitivity analysis. Both methods were implemented to determine the theoretical relationships between the change in humidity and/or temperature in each layer of corrugated board and its global bending, compression and shear stiffness. The procedure was used to analyze different types of 5-ply and 3-ply cardboard. The obtained results allowed to build a complete map of the relationship between the change in humidity of selected layers and the strength characteristics of the full assembly.

Hepatitis B virus (HBV) remains a dominant cause of hepatocellular carcinoma (HCC). Recently it was shown that HBV and woodchuck hepatitis virus (WHV) integrate into hepatocyte genome minutes after invasion. Retrotransposons and transposable sequences were frequent sites of the initial insertions suggesting a mechanism for spontaneous HBV DNA disperse throughout hepatocyte genome. Several somatic genes were also identified as early insertional targets in infected hepatocytes and woodchuck livers. Head-to-tail joints (HTJs) dominated amongst fusions indicating their creation by non-homologous-end-joining (NHEJ). Their formation coincided with robust oxidative damage of hepatocyte DNA. This was associated with activation of the poly(ADP-ribose) polymerase 1 (PARP1)-mediated dsDNA repair as reflected by augmented transcription of PARP1 and XRCC1, the PARP1 binding partner, OGG1, a responder to oxidative DNA damage, and by increased activity of NAD+, a marker of PARP1 activation, and HO1, an indicator of cell oxidative stress. The engagement of the PARP1-mediated NHEJ repair pathway explains HTJ format of the initial merges. The findings showed that HBV and WHV are immediate inducers of oxidative DNA damage, hijack dsDNA repair to integrate into hepatocyte genome and by this may initiate pro-oncogenic process. Tracking initial integrations may uncover early markers of HCC and help to explain HBV-associated oncogenesis.

Complex proteomic and physiological approaches to study cold and heat stress responses in plant mitochondria are still limited. Variations in the mitochondrial proteome of cauliflower (Brassica oleracea var. botrytis) curds after cold and heat and after stress recovery were assayed by 2D PAGE in relation to respiratory parameters. Quantitative analysis of the mitochondrial proteome revealed numerous stress-affected protein spots. In cold alternative oxidase isoforms were extensively upregulated; major downregulations in the level of photorespiratory enzymes, porine isoforms, oxidative phosphorylation (OXPHOS) and some low-abundant proteins were observed. On the contrary, distinct proteins, including carbohydrate metabolism enzymes, heat-shock proteins, translation, protein import, and OXPHOS components were involved in heat response and recovery. Few metabolic regulations were suggested. Cauliflower plants appeared less susceptible to heat; closed stomata in heat stress resulted in moderate photosynthetic, but only minor respiratory impairments, however photosystem II performance was unaffected. Decreased photorespiration corresponded with proteomic alterations in cold. Our results show that cold and heat stress not only operate in diverse mode (exemplified by cold-specific accumulation of some heat shock proteins), but exert some associations on molecular and physiological levels. This implies more complex model of action of investigated stresses on plant mitochondria.

This article presents a proposed system that enables energy transfer from the dc grid to a single-phase onboard grid, operating at an hi frequency. In addition to the energy transfer function, it additionally enables compensation of reactive power in the ac grid when the converter operates at less than rated power. To operate in compensator mode, it is necessary to decouple the current from the grid into active and reactive components and control them independently. To achieve good dynamics, synchronizers that operate in the dq system are used. In the case of a single-phase grid, it requires such a synchronizer to generate virtual quadrature signals. The used systems based on second-order generalized integrator are good, but to improve dynamics in the work a quadrature generator based on trigonometric calculations was proposed. The developed system was implemented in a proportional resonant current control system. Tests performed in steady state and in dynamic states related to typical grid disturbances showed better dynamic properties than the standard integrator-based system.Keywords: power transfer; compensator; P+R controller

The article presents a simplified method for determining the strength of a corrugated board packaging subjected to dynamic transport loads. The proposed algorithm consists of several calculation steps: (1) a static analysis of the compressive strength of the package, (2) an analysis of random vibrations in the frequency domain, used to determine the resonance frequencies, and (3) a dynamic analysis of the package loaded with computed resonant frequencies. For this purpose, numerical models of the static compression test of the packaging before and after the dynamic analysis of the package subjected to general transport loads were developed. In order to validate the model, the laboratory packaging compression tests were also performed for samples of boxes with 3-layer cardboard. Thanks to this, it was possible to verify the results of numerical simulations of compression tests for several box geometries. Which, in turn, allowed for the development of a method based on dynamic and post-dynamic (static) numerical analysis, allowing to determine with high accuracy the resistance of selected packaging to vibrations and dynamic loads. The results of the (validated experimentally) numerical analysis prove the usefulness of the simplified method presented here for precise estimation of the load capacity of various packages dynamically loaded during transport.

In engineering practice, one can often encounter issues related to optimization where the goal is to minimize material consumption, minimize stresses or deflections of the structure. In most cases, these issues are addressed with finite element analysis software and simple optimization algorithms. However, in the case of optimization of certain structures, it is not co straightforward. An example of such constructions are bubble deck ceilings, where in order to reduce the dead weight, air cavities are used, which are regularly arranged over the entire surface of the ceiling. In the case of these slabs, the flexural stiffness is not constant in all its cross-sections, which means that the use of structural finite elements (plate or shell) for static calculations is not possible, and therefore the optimization process becomes more difficult. The paper presents a minimization procedure of the weight of bubble deck slabs using numerical homogenization and sequential quadratic programming with constraints. Homogenization allows to determine the effective stiffnesses of the floor, which in the next step are sequentially corrected by changing the geometrical parameters of the floor and voids in order to achieve the assumed deflection. The presented procedure allows to minimize the use of material in a quick and effective way by automatically determining the optimal parameters describing the geometry of the bubble deck floor cross-section.

The paper presents a modified finite element method for nonlinear analysis of 2D beam structures. To take into account the influence of the shear flexibility, a Timoshenko beam element was adopted. The algorithm proposed enables using complex material laws without the need of implementing advanced constitutive models in finite element routines. The method is easy to implement in commonly available CAE software for linear analysis of beam structures. It allows to extend the functionality of these programs with material nonlinearities. By using the structure deformations, computed from the nodal displacements, and the presented here generalized nonlinear constitutive law, it is possible to iteratively reduce the bending, tensile and shear stiffnesses of the structures. By applying a beam model with a multi layered cross-section and generalized stresses and strains to obtain a representative constitutive law, it is easy to model not only the complex multi-material cross-sections, but also the advanced nonlinear constitutive laws (e.g. material softening in tension). The proposed method was implemented in the MATLAB environment, its performance was shown on the several numerical examples. The cross-sections such us a steel I-beam and a steel I-beam with a concrete encasement for different slenderness ratios were considered here. To verify the accuracy of the computations, all results are compared with the ones received from a commercial CAE software. The comparison reveals a good correlation between the reference model and the method proposed.

The article presents a modified finite element (FE) based algorithm for nonlinear analysis of 2D beam structures, which takes into account the influence of the shear forces. The method proposed enables using complex materials with nonlinearities without the need of implementing advanced constitutive models in FE routines. It can be directly integrated with commonly available FE software for linear analysis of beam structures, so its functionality can be easily extended also with material nonlinearities. The presented approach adopts the generalized constitutive law algorithm to iteratively modify the stiffness of beam element. To address an influence of a shear stiffness, a Timoshenko beam element was used. The methodology was implemented and its performance was verified on several numerical examples. For validation, the displacements and the ultimate loads were compared with the values from a commercial FE software. The results shown a good correlation between the reference model and the method proposed.

In the paper, a modified nonlinear finite element method for analysis of trapezoidal plates geometrically reduced to shallow-shell Reissner-Mindlin formulation is presented. Due to the method proposed the complex plate cross-section and nonlinear materials may be modelled and no implementation of advanced constitutive law via user subroutines is needed. The generalized nonlinear constitutive law is used to update the stiffness of the plate element. The method enables modeling of complicated cross-sections, such as steel trapezoidal sheets, metal facing sandwich panels or reinforced concrete. Additionally, for those geometrically complex sections an advanced nonlinear material may be adopted. To verify the proposed method, a selected trapezoidal sheets were modeled in a commercial software as full 3D shell structures. By comparing displacements and forces, it was shown that both models behave almost identically, however, the simplified model has about 300-400 times less degrees of freedom, thus it is much more efficient.

Objective: The future mobility challenges leads to considering new safety systems to protect vehicle passengers in non-standard and complex seating configurations. The objective of this study is to assess the performance of a brand new safety system called nanobag and to compare it to the traditional airbag performance in the frontal sled test scenario. Methods: The nanobag technology is assessed in the frontal crash test scenario and compared with the standard airbag by numerical simulation. The previously identified material model is used to assemble the nanobag numerical model. The paper exploits an existing validated human body model to assess the performance of the nanobag safety system. Using both the new nanobag and the standard airbag, the sled test numerical simulations with the variation of human bodies are performed in 30 km/h and 50 km/h frontal impacts. Results: The sled test results for both the nanobag and the standard airbag based on injury criteria shows a good and acceptable performance of the nanobag safety system compared to the traditional airbag. Conclusion: The results show that the nanobag system has its performance compared to the standard airbag, which means that thanks to the design, the nanobag safety system has a high potential and extended application for multi-directional protection against impact.

The article presents a cyber-physical system for acquiring, processing and reconstructing images from measurement data. The technology was based on process tomography, intelligent measurement sensors, machine learning, Big Data, Cloud Computing, Internet of Things as a solution for Industry 4.0. Industrial tomography enables observation of physical and chemical phenomena without the need of internal penetration and allows real-time monitoring of production processes. The application includes specialized intelligent devices for tomographic measurements and dedicated algorithms for solving the inverse problem. The work focuses mainly on electrical tomography and image reconstruction using deterministic methods and machine learning, the reconstruction results were compared, different measurement models were used. The researches were carried out for synthetic data and laboratory measurements. The main advantage of the proposed system is the possibility of spatial data analysis and their high processing speed. The presented research results show that the process tomography gives the possibility to analyse the processes taking place inside the facility without disturbing the production, analysis and detection of obstacles, defects and various anomalies. Knowing the characteristics of a given solution, the application allows you to choose the appropriate method to reconstruct the image.

Artificial intelligence is increasingly used in various branches of engineering. In this article, artificial neural networks are used to predict the crush resistance of corrugated packaging. Among the analysed packages were boxes with ventilation openings, packages with perforations, and typical flap boxes, which makes the proposed estimation method very universal. Typical shallow feedforward networks were used, which are perfect for regression problems, mainly when the set of input and output parameters is small, so no complicated architecture or advanced learning techniques are required. The input parameters of the neural networks are selected so as to take into account not only the material used for the production of the packaging, but also the dimensions of the box and the impact of ventilation holes and perforations on the load capacity of individual walls of the packaging. In order to maximize the effectiveness of neural network training process, the group of input parameters was changed so as to eliminate those to which the sensitivity of the model was the lowest. This allowed the selection of the optimal configuration of training pairs for which the estimation error was on the acceptable level. Finally, models of neural networks were selected, for which the training and testing error did not exceed 10%. The demonstrated effectiveness allows to conclude that the proposed set of universal input parameters is suitable for efficient training of a single neural network model capable of predicting the compressive strength of various types of corrugated packaging.

The paper presents the results of energy and environmental analysis of geothermal CHP plant operation in Polish conditions. As the most favorable, for the geothermal conditions prevailing in Poland, the variant of CHP plant based on Organic Rankine Cycle (ORC) has been taken into consideration. As the case study the existing geothermal well located in the town of Konin in the Wielkopolska voivodship has been chosen. The conceptual design of CHP plant has been proposed and evaluated from energy and environmental point of view. As energy performance criteria the non-renewable primary energy consumption has been chosen. In case of environmental performance carbon dioxide emission has been taken as evaluation criteria. The analysis has been performed for different operating conditions and three working fluids.

The Ponto-Caspian region is the main donor of invasive amphipods to freshwater ecosystems, with at least 13 species successfully established in European inland waters. Dikerogammarus spp. and Pontogammarus robustoides are among the most successful, due to their strong invasive impact on local biota. However, genomic knowledge on these invaders is scarce, while phylogeography and population genetics have been based on short fragments of mitochondrial markers or nuclear mi-crosatellites. In this study, we provide: (i) reconstruction of four mitogenomes for four invasive gammarids; (ii) comparison between the structure of the newly obtained mitogenomes and to those from literature; (iii) SNP calling rates for individual D. villosus and D. haemobaphes from different invasion sites across Europe; and (iv) the first time-calibrated full mitogenome reconstruction of several Ponto-Caspian taxa. We have sequenced, assembled and annotated four mitogenomes, each from D. villosus, D. hae-mobaphes, D. bispinosus and Pontogammarus robustoides. We found that, in comparison to other gammarids, the mitogenomes of Ponto-Caspian species show a translocation between the tRNA-E and tRNA-R positions. Phylogenetic reconstruction using the mitogenomes identified that Ponto-Caspian gammarids form a well-supported group that originated in the Miocene. Our study supports paraphyly in the family Gammaridae. These mitogenomes serve as vital genetic resources for the development of new markers for PCR-based identification methods and demographic studies.

Pharmaceutical aerosols play a key role in the treatment of lung disorders, but also systemic diseases, due to their ability to target specific areas of the respiratory system (RS). This article focuses on identifying and clarifying the influence of various factors involved in the generation of aerosol micro- and nanoparticles on their regional distribution and deposition in the RS. Attention is given to the importance of process parameters during aerosolization of liquids or powders and the role of aerosol flow dynamics in RS. The interaction of deposited particles with the fluid environment of the lung is also pointed out as an important step in the mass transfer of the drug to the RS surface. The analysis presented highlights the technical aspects of preparing the precursors to ensure that the properties of the aerosol are suitable for a given therapeutic target. Analyzing existing technical limitations, several potential strategies for enhancing the efficiency of targeted therapeutic delivery to or through the respiratory system are identified and presented, including the use of smart inhaling devices incorporating AI algorithms.

Extracts obtained from leaves of Moringa tree (Moringa oleifera) are a rich source of many bioactive compounds: flavonoids, phenolic acids or carotenoids. It also contains such components as, vitamins (A, C, niacin, pantothenic acid), alkaloids, tannins or saponins. Extracts and plant substances derived from the leaves of Moringa oleifera L. have a strong antioxidant, toning and anti-inflammatory effect. The work attempts to obtain a multifunctional plant extract derived from Moringa tree leaves. Obtained extracts was analyzed for their biochemical and physicochemical properties. The obtained results indicate on a strong antioxidative potential of the tested extracts. The further step was an attempt to apply the extracts in the model body wash cosmetic. The biological activity of extracts and model cosmetic formulation were assayed by in vitro analysis on two human cell lines: keratinocytes (HaCat,) and fibroblasts (BJ). The results showed that the tested extracts may affect on increasing of cell proliferation and reduce oxidative stress in cells. The addition of the tested extracts to the model cosmetic formulation, were contributed to the reduction of their ability to irritate the skin and improve the safety of use of the product.

The early generative phase of cauliflower (Brassica oleracea var. botrytis) curd ripening is sensitive to the water deficit. Mitochondrial responses under drought within Brassica genus are poorly understood. The main goal of this study was to investigate the mitochondrial biogenesis of three cauliflower cultivars varying with drought tolerance. Diverse quantitative changes (down-regulations mostly) in the mitochondrial proteome were assayed by 2D PAGE coupled with LC-MS/MS. Respiratory (e.g. CII, CIV and ATP synthase subunits), transporter (including diverse porin isoforms) and matrix multifunctional proteins (e.g. components of RNA editing machinery) appeared diversely affected in their abundance under two drought levels. Western immunoassays showed also cultivar-specific responses of selected mitochondrial proteins. Dehydrin-related tryptic peptides found in few 2D spots that appeared immunopositive with dehydrin-specific antisera highlighted the relevance of mitochondrial dehydrin-like proteins for the drought response. The level of selected messengers participating in drought response was also determined. We conclude that the mitochondrial biogenesis was strongly, but diversely affected in various cauliflower cultivars and associated with drought tolerance on the proteomic and functional levels. However, transcriptomic and proteomic regulations were largely uncoordinated due to the suggested altered availability of messengers for translation, mRNA/ribosome interactions and/or miRNA impact on transcript abundance and translation.

The correlation between pain and emotional status in subjects with temporomandibular disorders (TMD) is known. Regardless of that up to date these findings were seldomly confronted with the objective assessment of pain using a digital algometer on the mastication muscles. The aim of the study was to investigate the relationship between the emotional status, chronic pain pain pressure threshold (PPT). 38 subjects were screened for the existence of temporomandibular disorders with the 3Q/TMD questionnaire, for chronic pain (GCPS) and emotional status (PHQ-9 and GAD-7). The results were confronted with the PPT measured with the digital algometer on the masseter muscles. Each subject was examined three times (after 1 month and after 7 months from the initial exami-nation session. Chronic pain scores (GCPS) were found to be higher in the TMD group in all three examination sessions (p<0,05). The pain, depression and anxiety levels were higher in females de-spite the existence of TMD, but only some were significant.A correlation between chronic orofacial pain scores and PPT was found in 2 out of 3 examination sessions. The PPT scores on the masseter muscles did not correlate with the emotional state in the study population.

Cryptosporidiosis is a widespread disease caused by the parasitic protozoan Cryptosporidium spp., which infects various vertebrate species, including humans. Once unknown as a gastroenteritis-causing agent, Cryptosporidium spp. is now recognized as a pathogen causing life-threatening disease, especially in immunocompromised individuals such as AIDS patients. Advances in diagnostic methods and increased awareness have led to a significant shift in the perception of Cryptosporidium spp. as a pathogen. Nowadays, genomic and proteomic studies have played a main role in understanding the molecular biology of this complex-life-cycle parasite. Genomics has enabled the identification of numerous genes involved in the parasite's development and interaction with hosts. Proteomics has allowed for the identification of protein interactions, their function, structure, and cellular activity. The combination of these two approaches has significantly contributed to the development of new diagnostic tools, vaccines, and drugs for cryptosporidiosis. In this review, we summarize the major accomplishments in the field of Cryptosporidium research using genomics and proteomics.

The aim of the research was to evaluate various fertilisation programs in increasing plant resistance to abiotic stress such as drought. It was tested whether the algal biostimulator provides the same tolerance to drought stress in highbush blueberry plants as regular fertilisers without biostimulation. The research was conducted in 2022 in a greenhouse in controlled drought conditions. Three-year-old highbush blueberry bushes (12 pieces) were used in the experiment. Highbush blueberry bushes (Vaccinium corymbosum) 'Brigitta Blue' cultivars were planted in plastic pots with a capacity of 10 dm3 containing an acidic substrate and placed in a greenhouse. Controlled lighting conditions were maintained using sodium lamps and a temperature of 25°C/20°C day/night. The substrate in pots was maintained at 80% of field water capacity by manual watering and weekly supply of nutrient solution for 5 weeks until water deficit occurred. Half of the plants were sprayed weekly with a biostimulant based on seaweed extract. Seven days after the third application of the product, half of the untreated and treated plants were subjected to water deficit stress by restricting water supply to 40% of field capacity. The tested biostimulator impacted on stimulating the activity of antioxidant enzymes but had no effect on the chlorophyll content in the leaves or the concentration of nutrients in the leaves. The effect of marine algae products on the yield quantity and high quality is related among other to bioactiv substances witch helps to prevent drought stress.

Cancer is one of the leading causes of death and morbidity with a complex pathophysiology. Traditional cancer therapies include chemotherapy, radiation therapy, targeted therapy, and immunotherapy. However, limitations such as lack of specificity, cytotoxicity, and multi-drug resistance pose a substantial challenge for favorable cancer treatment. The advent of nanotechnology has revolutionized the arena of cancer diagnosis and treatment. Nanoparticles (1-100nm) can be used in the treatment of cancer owing to their specific advantages such as biocompatibility, reduced toxicity, more excellent stability, enhanced permeability and retention effect, and precise targeting. Nanoparticles are classified into several main categories. The nanoparticle drug delivery system is particular and utilizes tumor and tumor environment characteristics. Nanoparticles not only solve the limitations of conventional cancer treatment but also overcome multidrug resistance. Additionally, as new multidrug resistance mechanisms are unraveled and studied, nanoparticles are being investigated more vigorously. Various therapeutic implications of nano-formulations have created brand new perspectives for cancer treatment. However, a majority of the research is limited to in vivo and in vitro studies, and the number of nano-drugs that are approved has not much amplified over the years. In this review, we discuss numerous types of nanoparticles, targeting mechanisms along with approved nanotherapeutics for oncological implications in cancer treatment. Further, we also summarize the current perspective, advantages, and challenges in clinical translation.

We present the results of calculations of magnetic properties of 3 compounds from Laves phase C15 family: DyAl2, HoAl2 and ErAl2 performed with a new computation system called ATOMIC MATTERS MFA. We compare these findings with the recently published results for TbAl2, GdAl2 and SmAl2. The calculation methodology was based on the localized electron approach applied to describe the thermal evolution electronic structure of rare-earth R3+ ions over a wide temperature range and to compute magnetocaloric effect (MCE). Thermomagnetic properties were calculated based on the fine electronic structure of 4f9, 4f10 and 4f11 configurations of the Dy3+, Ho3+, Er3+ ions, respectively. Our calculations yield the magnetic moment value and direction; single-crystalline magnetization curves in zero field and external magnetic field applied in various directions of m(T, Bext); the 4f-electronic components of specific heat c4f(T, Bext); and temperature dependence of the magnetic entropy and isothermal entropy change with external magnetic field -S(T, Bext). The cubic CEF parameter values used for DyAl2 calculations are taken from earlier research of A.L. Lima, A.O. Tsokol and recalculated for universal cubic parameters (Amn) for the RAl2 series. Our studies reveal the importance of multipolar charge interactions when describing thermomagnetic properties of real 4f electronic systems and the effectiveness of an applied self-consistent molecular field in calculations for magnetic phase transition simulation.

The authors of the paper have made an attempt to detect the fibre content and fibre spacing in a steel fibre reinforced concrete (SFRC) industrial floor. Two non-destructive testing (NDT) methods: an electromagnetic induction technique and a radar-based technique were applied. The first method allowed to detect the spacing in subsequent layers located in the thickness of the slab. The result of the second method was a 3D visualization of the detected fibre in the volume of concrete slab. The conducted tests showed aptitude and limitations of the applied methods in estimating fibre volume and spacing. The two techniques also allowed to locate the areas with relatively low fibre concentration which are very likely to be characterized by low mechanical properties.

This study concerns calculation and comparison of Fe, Co, Ni and Cu deposition rates in tungsten codeposition process based on electrodeposition of numerous tungsten alloys. 8 different tungsten alloys containing from 2 to 5 metals were electrodeposited in constant conditions in order to compare exact reduction rates. Calculated rates enabled control of the alloy composition precise enough to obtain a high-entropy WFeCoNiCu alloy with well-balanced composition. Introduction of copper to form the quinternary alloy was found to catalyze the whole process, increasing deposition rates of all components of the high-entropy alloy.

"Deep fake" technologies are often associated with face-swapping algorithms based on images or videos. Although much research is focused on developing these techniques, there is still room for improvement, especially in human and visual assessment. In this study, we present an innovative approach to the problem of face replacement based on one model while preserving background features. Our model uses the Adaptive Attentional Denormalization method from FaceShifter while integrating identity features from the ArcFace and BiSeNet models to support the attribute extraction process. We used Fast GAN as a generative model to optimize and accelerate the training process on smaller data sets. Our research proves the effectiveness of the proposed approach by combining innovative methods and architectures in one coherent solution.

The article presents the influence of ecological agents, i.e. the effective microorganisms and silver compounds addition to lubricating oil on operating parameters of an internal combustion engine. The basic diagnostic parameters of a piston engine determining its technical condition were described. In the further part, the research stand and materials were presented. In the main part of this article for pure oil compared to oil with the effective microorganisms and silver compounds addition were shown. It was found that the addition of effective microorganisms and silver compounds to the oil reduces the emission of toxic components into the atmosphere along with the exhaust gases, while the remaining engine operating parameters for each load value show that these additives do not cause deterioration of the technical condition of the tested engine. Of all the agents used, the best results are obtained with the addition of ceramic tubes, because it is an additive that does not affect the properties of the oil in its composition. The advantage of ceramic tubes is the slow release of effective microorganisms, which has an effect on the parameters of the oil and thus on the operation of the engine. In further research, it will be checked how these additives affect the anti-seize and anti-wear properties of the lubricating oil used, which should give a broader view of the impact of these additives on the technical condition of the operated piston engine.

On the analyzed section of 2.4 km of the national road No. 50 of the Młodzieszyn bypass, it was carried out by a consortium of OAT and SAT companies in the period April-September 2019, under constant traffic in the field of repairing the concrete pavement by replacing slabs, levelling them and sealing expansion joints, roughening and roadside reinforcements.

The report [1] shows that in many European cities the sewer system is older than 40 years, potentially reducing their ability to cope with more intense pluvial flooding [2] addition to climate change, urbanization is an important factor increasing the flooding risk, as it increases of impervious surfaces. Flash floods are particularly troublesome, causing not only the overloading of drainage systems [3], but also urban transport disruption, affecting human health, and contributing to pollution due to untreated sewage discharges [4]. Pluvial floods in urban areas are caused by short-duration precipitation, high intensity and on small scale. Such rainfall is difficult to predict and does not always apply to catchment areas. In Poland, heavy rainfall lasts relatively short, from a few minutes to a few, at most, several hours [5]. The method of the Analytic Hierarchy Process (AHP) was used to rank the importance of criteria characterizing exposure in urban areas. The ranking is based on expert judgements. The article focuses on exposure which is one of the components of risk. Geographical Information System (GIS) is integrated with Multicriteria Decision Analysis (MCDA) to evaluate exposure of urban area on pluvial floods.

Metal matrix composite are used in such fields of technology, such as: aerospace, electronics, energy, industry, defense, automotive, aviation, shipbuilding, and more. Composite coatings of ceramic - metals is used primarily to enhance the durability of machine parts. Therefore, new materials are permanently looked for, what has resulted in the past in development of composite materials. The coatings dispersed are consisting of metallic matrix (metals and their alloys) and small non-metallic particles. The deposition of ceramic particles simultaneously with metallic matrix leads often to composite coatings possessing properties much better than those of metallic coating. The nickel and less often, other iron group elements are usually used as a matrix and Al2O3 as tough particles. The welding technology of applying alloy and composite coatings is widely used. The technology of infrasound thermal spraying of metal matrix composite coatings was presented. It is a simple technology and a very useful one in ship machinery regeneration during the cruise craft (e.g. internal combustion engines, torque pumps, separators). The metal matrix composite coatings must undergo finishing due to high surface roughness after application. In the article to used finishing by plastic working and machining of coatings nickel matrix composite was proposed.

The article presents the methodology for classifying economic regions with regards to selected factors that characterize a region, such as: the economic structure of the region, and thus the share of individual sectors in the economy; employment; the dynamics of the development of individual sectors expressed as an increase or decrease in production value; the population density in the region and also the level of occupational safety. Cluster analysis, which is a method of multidimensional statistical analysis available in Statistica software, was used to solve the task. The proposed methodology was used to group Polish voivodships with regards to the speed of economic development and occupational safety in the construction industry. Data published by the Central Statistical Office was used for this purpose, such as the value of construction and assembly production, the number of people employed in the construction industry, the population of an individual region and the number of people injured in occupational accidents.

There is increasing use of wood-based composites in industry not only because of the shortage of solid wood, but above all for their better properties such as: strength, aesthetic appearance, etc. compared to wood. Medium density fibreboard (MDF) is a wood-based composite that is widely used in the furniture industry. The goal of the research conducted was to determine the effect of the type of coating on the drill cutting blades on the value of thrust force (F_t), cutting torque (M_c), cutting tool temperature (T) and surface roughness of the hole in drilling MDF panels. In the tests three types of carbide drills (HW) were used: not coated, TiAlN coated and ZrN coated. The measurement of both the thrust force and the cutting torque was carried out using an industrial piezoelectric sensor. The temperature of the cutting tool in the drilling process was measured using an industrial temperature measurement system using a K-type thermocouple. It was found that the value of the maximum temperature of the tool in the drilling process depends not only on the cutting speed and feed rate, but also on the type of coating of the cutting tool. The value of both the cutting torque and the thrust force is significantly influenced by the value of the feed rate and the type of drill coating. The effect of varying plate density on the surface roughness of the hole and the variation of the value of the thrust force is also discussed. The results of the investigations were statistically analysed using a multi-factorial analysis of variance (ANOVA).

The corrugated board is a versatile and durable material that is widely used in the packaging industry. Its unique structure provides strength and cushioning, while its recyclability and bio-degradability make it an environmentally friendly option. The strength of corrugated board depends on many factors, including the type of individual papers on flat and corrugated layers, the geometry of the flute, temperature, humidity, etc. This paper presents a new approach to analysis geometric features of corrugated boards based on the images. It allows for precise determination of the geometry of the corrugated layer, as well as the thickness of individual papers in all cardboard layers. The experimental set used in the work and the created software are characterized by high reliability and precision of measurement thanks to the use of an identification procedure based on image analysis and evolutionary algorithms. This allows to quickly find the main geometric characteristics of the corrugated board, which in turn leads to the possibility of performing numerical analyzes taking into account the real model of the corrugated board. Calculations made on a real (correctly mapped geometrically) model allow, for example, a more reliable analysis of the composition of the cardboard, and thus also to obtain greater savings in the optimization process.

The length of stay (LOS) in the hospital emergency department (ED) is a crucial key performance indicator that is used to track and manage the performance of the ED as a whole. Our study had two objectives. Firstly, we aimed to evaluate the association between LOS and the most common primary ICD-10 diagnoses. To achieve this, we examined LOS in groups with specific (internal, surgical, neurological, and traumatic diseases) and non-specific diagnoses in adult ED visits at a tertiary referral hospital between 2017 and 2019 (134,675 visits in total). Our secondary objective was to measure LOS by age, day of the week, time of day, and season. The mean LOS was 254 minutes and was the shortest in the traumatic group (160 minutes), while in other groups it was significantly longer: neurological by 185 minutes, internal medicine by 158 minutes, surgical by 36 minutes, and non-specific by 24 minutes. In conclusion, non-specific diagnoses accounted for 21% of all ICD-10 primary diagnoses. In this group of patients, the percentage of hospitalizations was the highest. Other significant determinants of LOS were the patients’ age, the day of the week, the time of arrival, and repeated visits.

A novel approach based on response surface methodology (RSM) was developed to predict and apply the best extraction conditions for the isolation of various-type polyphenolic antioxidants from the dried flower buds of Magnolia x soulangeana Soul.-Bod. var. ‘Lennei’ (Magnoliaceae). As a method of choice, ultrasound-assisted extraction was used and the optimized extraction parameters (temperature, time of extraction, the composition of aqueous-ethanolic extractants and solvent to solid ratio) have been determined using a central composite design factorial analysis, followed by appropriate spectrophotometric methods (with Folin–Ciocalteu and 2,2-diphenyl-1-picrylhydrazyl reagents) to determine the antioxidant and antiradical potential of extracts, respectively. The use of 66.8% (V/V) ethanol, as the extraction solvent during the 55.2 min extraction protocol, and the ratio of extractant volume to herbal substance of 46.8 mL/g gave the highest total yield of bioactive antioxidant phenolics in the extract obtained. For this herbal preparation, qualitative and quantitative analysis was performed using combined chromatographic (LC), spectroscopic (PDA) and tandem mass spectrometric (ESI-QTOF–MS/MS) techniques. A detailed phytochemical profiling, conducted for the first time, documented substantial amounts of polyphenolic antioxidants, especially phenylethanoids and flavonoids in the flower buds of M. soulangeana ‘Lennei’. Their average total content exceeded 30.3 and 36.5 mg/g dry weight, respectively.

Corrugated board, widely used in the packing industry, is a recyclable and durable material. Its strength and cushioning, influenced by geometry, environmental conditions like humidity and temperature, and paper quality, make it versatile. Double-walled (or five-ply) corrugated board, comprising two flutes and three liners, enhances these properties. This study introduces a novel approach to analyze 5-layered corrugated board, extending a previously published algorithm for single-walled boards. Our method focuses on measuring layer and overall board thickness, flute height, and center lines of each layer. Integrating image processing and genetic algorithms, the research successfully developed an algorithm for precise geometric feature identification of double-walled boards. Images were recorded using a special device with a sophisticated camera and image sensor for detailed corrugated board cross-sections. Demonstrating high accuracy, the method faced limitations only with very deformed or damaged samples. This research contributes significantly to quality control in the packaging industry and paves the way for further automated material analysis using advanced machine learning and image sensors. It emphasizes the importance of sample quality and suggests areas for algorithm refinement to enhance robustness and accuracy.

The article focuses on derivation of simplified predictive models for identification of overall compressive stiffness and strength of corrugated cardboards. As a representative example an unsymmetrical 5-ply sample (with E and B flute) was used in this study. In order to exclude unreliable displacement measurement in the standard edge crush test, the virtual strain gauges are used. Video extensometry is employed here to collect measurements from the outer surfaces of the sample on both sides. Additional data allows for obtaining real force-displacement curves, which are used in the validation procedure. To emulate the experimental results, beside simple analytical model, also a 3D numerical model fully reflecting the geometry of the corrugated board, based on finite elements method was also built. In both cases a good agreement between the experimental results and the analytical and numerical calculations was observed. This proves that the proposed analytical model can be successfully used to determine the overall stiffness and compressive strength of the corrugated board, provided that the geometry and properties of all the layers of the board are known. The simple model presented in this work enables quick and reliable design and prototyping of new assemblies without the need to manufacture them.

The study presents the effect of annealing process parameters on the microstructure, hardness and strain hardening coefficients i.e., the strength coefficient c and the strain hardening exponent n, of 42CrMo4 steel. Seven selected annealing time-temperature schemes are examined for superior steel formability in cold metal forming conditions. The c and n coefficients are first determined in experimental upsetting of annealed samples and then used in FEM simulations of the upsetting process. The results demonstrate that the strain hardening coefficients (c and n) depend on the employed annealing scheme. Compared to the as-received sample, the annealing process reduces the true stress and effectively decrease the hardness of 42CrMo4 steel, improves microstructural spheroidization and, consequently, facilitates deformability of this material. The annealing schemes relying on heating the material to 750 °C and its subsequent slow cooling lead to the highest decrease in hardness ranging from 162 to 168HV. Results obtained with the SEM-EDS, LOM and XRD methods lead to the conclusion that the employed heat treatment schemes cause the initial ferritic-pearlitic microstructure to develop granular and semi-lamellar precipitation of cementite enriched with Mo and Cr in the ferrite matrix. In addition, the annealing process affects the growth of α-Fe grains. The highest cold hardening rate, and thus formability, is obtained for the annealing scheme producing the lowest hardness. The results of FEM simulations are positively validated by experimental results. Obtained results are crucial for further numerical simulations and experimental research connected with developing new cold metal forming methods for producing parts made of 42CrMo4 steel.

The aim of the study was to compare the standard baseline imaging, with extended radiological staging. To assess our hypothesis, we performed a prospective, single-centre study which included 132 participants recruited between October 2015 and March 2020. Descriptive statistics, the Friedman and chi-squared tests were performed and p &lt; 0.05 was considered significant. Patients were grouped into two cohorts, CT scan cohort (n=87) and PET-CT cohort (n=43). In the first group the originally determined disease stage changed in 36.8 % of cases, in second group in 51.2 %. The consistency between assessment of axillary lymph nodes by imaging (cN) and the postoperative pathology report (pN) was evaluated. In most cases, clinical and pathological evaluation of involved nodes was consistent, for CT scan the result was χ2(1) = 18.98; p &lt; 0.001, for PET-CT the result was χ2(1) = 6.41; p = 0.03. Highly customized radiation therapy defined as dose boost within the involved lymph nodes, not covered by surgeon, was applied in nine patients.

Virtual human body models contribute to designing safe and user-friendly products through virtual prototyping. Anthropometric biomechanical models address different physiques using average dimensions. In designing personal protective equipment, biomechanical models with the correct geometry and shape shall play a role. The presented study shows the variations of subject-specific anthropometric dimensions from the average for the different population groups in the Czech Republic and China as a background for the need for personalized human body models. The study measures a set of clothing industry dimensions of Czech children, Czech teens, Czech adults and Chinese adults and compares them to the corresponding age average, which is represented by a scaled anthropometric human body model. The cumulative variation of clothing industry dimensions increases the farer is the population group from the average. It is smallest for the Czech adults 7.54% ± 6.63%, Czech teens report 7.93% ± 6.25% and Czech children differ 9.52% ± 6.08%. Chinese adults report 10.86% ± 11.11%. As the variations of the particular clothing industry dimensions from the average prove the necessity of having personalized subject-specific models, the personalization of particular body segments using the measured clothing industry dimensions leading to a subject-specific virtual model is addressed. The developed personalization algorithm results in the continuous body surface desired for contact applications for assessing body behavior and injury risk under impact loading.

Energy transition is one of the greatest challenges facing humanity today. All micro, small, medium and large enterprises in operation will have to face it, and some can al-ready boast the first successes in this regard. This paper focuses on the involvement of these smallest players in energy transition. Micro and small entities are the largest part of the economy, having a great influence on its development. Looking at the wide scale of their activities, these entities are distinguished by a specific owner-manager relationship. This means that the final decision-making is influenced by business goals, but also by the manager's approach, their awareness of changes, and personal and other factors. Based on a structured and standardized survey questionnaire, the research was carried out using the Computer-Assisted Telephone Interviewing technique between April and May 2022 among owners of micro and small enterprises operating in Poland. The survey showed that active engagement of micro and small enterprises in energy efficiency initiatives is related to their market success and financial health.

Colours were ubiquitous in the medieval world, and castles were no exception. While in the eyes of most people their rich colour schemes manifested power and wealth, some could also read the more nuanced messages these colours conveyed. The main objective of this paper is to discuss the use and role of colour in the interiors of castles of medieval Bohemia and Poland. The picture is complemented by the analysis of colour decorations of defensive residences of the Teutonic Order, for which colour schemes of external facades can be addressed as well. The dis-cussion takes into account the varying state of preservation and draws from the available writ-ten accounts. To present the most complete picture possible, we discuss royal residences, for which unfortunately limited data is available, as well as better-preserved castles of dukes and knights. We discuss the identified iconographic programmes and their chivalric, heraldic, and hagiographic motifs. Also within the scope of our discussion are late forms of floral decorations, known as “green chambers”. The numerous examples presented in the paper prove that colour was an important tool of visual social communication in castle architecture: it complemented the symbolism, and sometimes carried an independent message.

This study comprehensively investigates Al2O3's mechanical properties, focusing on fracture toughness, surface energy, Young's modulus, and crack propagation. The density functional theory (DFT) is employed to model the vacancies in Al2O3, providing essential insights into this material’s structural stability and defect formation. The DFT simulations reveal a deep understanding of vacancy-related properties and their impact on mechanical behavior. In conjunction with molecular dynamics (MD) simulations, the fracture toughness and crack propagation in Al2O3 are explored, offering valuable information on material strength and durability. The surface energy of Al2O3 is also assessed using DFT, shedding light on its interactions with the surrounding environment. The combination of DFT and MD simulations provides a robust framework for a comprehensive understanding of Al2O3's mechanical properties, with implications for material science and engineering applications.

The aim of the study was to determine the presence Fusarium species and mycotoxins in winter wheat grain in Poland. Grain samples from different locations in Poland in 2009 and 2010 were analysed for the content of biomass of Fusarium species and mycotoxins. In 2009 biomass of F. graminearum and F. poae was present in all samples, F. culmorum in 82% of samples, F. avenaceum in 55% of samples. F. sporotrichioides, F. tricinctum and F. equiseti were found only in individual samples. F. langsethiae was not detected. In 2010, five Fusarium species were detected with the exception of F. sporotrichioides. The highest content of biomass was found for F. graminearum followed by F. avenaceum, F. poae and F. langsethiae. The amount of F. culmorum biomass was very low. The most frequently occurring species was F. poae and F. graminearum. In 2009, deoxynivalenol was detected in all samples. In 2010, the average content of deoxynivalenol was lower than in 2009. Nivalenol was detected at very low concentration in both years. Significant correlations between content of F. graminearum biomass and deoxynivalenol concentration in grain and between content of F. poae biomass and nivalenol concentration in grain in 2009 were found. The most important finding of this study was that main Fusarium species infecting wheat kernels in Poland in both years was F. graminearum. The amount of biomass of F. graminearum was the highest in both years. It was present in the most samples. The other frequently detected species was F. poae, which in 2010 appeared in more samples than F. graminearum. However, the amount of F. poae biomass was lower. F. culmorum, species that was previously dominating as wheat pathogen in Poland, was found less frequently than F. graminearum. The amount of biomass of this species was the lowest in 2010.

Fusarium head blight (FHB) can cause contamination of cereal grain with mycotoxins. Winter wheat is also infected with FHB. It is more resistant than durum wheat to head infection and less than other small grain cereals. The aim of this study was to identify winter wheat lines that combine low head infection and kernel damage with low toxin contamination. Resistance to FHB of 27 winter wheat lines and cultivars was evaluated over a three-year experiment established in two locations. At the anthesis stage, heads were inoculated with Fusarium culmorum isolates. The FHB index was scored and the percentage of Fusarium-damaged kernels (FDKs) assessed. The grain was analysed for type B trichothecenes (deoxynivalenol and derivatives, nivalenol) and zearalenone content. The average FHB index was 12.9%. The proportion of FDK was 6.9% (weight) and 8.5% (number). An average content of deoxynivalenol amounted to 3.543 mg/kg and nivalenol to 2.115 mg/kg. In total, it was 5.804 m/kg of type B trichothecenes. The zearalenone content in the grain was 0.214 mg/kg. Relationships between FHB index, FDK and mycotoxin contents were highly significant for wheat lines; however, they were stronger for FDK versus mycotoxins. Breeding lines combing all types of FHB resistance were found, and five of them had resistance similar to that of wheat lines with the Fhb1 gene.

This paper presents the results of laboratory tests of CFRP (carbon fibre-reinforced polymer) laminates, which allowed the development of numerical material models. The obtained data were used in a further stage to perform numerical simulations of four variants of medical tabletops differing, among other features, in the shape of the cross-section. Maximum deflections and effort in the composite material were analyzed. The final step was to perform a laboratory test for one of the tabletop versions, the results of which confirmed the correctness of the numerical calculations. This work is aimed at both researchers and designers involved in the practical application of fibre-reinforced polymer matrix composites.

Plants produce specific structures constituting a barrier hindering penetration of pathogens, while they also produce substances inhibiting pathogen growth . These compounds are secondary metabolites, such as phenolics, terpenoids, sesquiterpenoids, resins, tannins and alkaloids. Bioactive compounds are secendary metabolities from trees and shrubs are used in medicine, herbal medicine and cosmetology. To date fruits and flowers of exotic trees and shrubs have been primarily used as sources of bioactive compounds. In turn, search for new sources of bioactive compounds is currently focused on native plant species due to its availability. Application of such raw material needs to be based on knowledge of their chemical composition, particularly health-promoting or therapeutic compounds. Research conducted to date on European trees and shrubs has been scarce. This paper presents results of literature studies conducted to systematise knowledge on bioactive compounds found in trees and shrubs native to central Europe. The aim of this review providing available information on the subject is to indicate gaps in the present knowledge.

Per- and polyfluoroalkyl substances (PFASs) are a group of fluorinated, organic, man-made chemicals; they do not occur naturally in the environment. This study aimed to determine the profile and content of PFASs in volunteers’ blood plasma and urine after fermented red beetroot juice consumption and correlated it with the blood parameters. During 42 days, 24 healthy volunteers intake 200 mL/60 kg of body weight fermented red beetroot juice. PFASs were analyzed using micro-HPLC-MS/MS method. Five perfluoroalkyl substances were found in human body fluids. After juice consumption, PFASs, due to the consumption of food contaminated with them, was discovered that for perfluorocarboxylic acids, a downward trend was observed, while for perfluoroalkane sulfonates, their plasma content showed a statistically significant upward trend. Analysis of the hematology parameters indicated that the intake the fermented red beetroot juice showed a significant decrease in mean corpuscular volume (MCV), platelets concentration, mean platelet volume (MPV), platelet large cell ratio (P-LCR) at the significance level p < 0.01, and he-matocrit (p < 0.05). On the other hand, the dietary intervention also indicated a significant (p < 0.01) increase corpuscular/ cellular hemoglobin concentration (MCHC). In the case of blood biochemi-stry, no significant change in blood samples after intake the fermented beetroot juice was observed. However, a decreasing tendency of total cholesterol and low-density lipoprotein concentration (LDL-C) were observed. Based on the presented results, there is a need to analyze and monitor health-promoting food regarding undesirable substances and their impact on consumer health.

This paper presents a new low-voltage versatile mixed-mode filter which uses a multi-ple-input/output differential difference transconductance amplifier (MIMO-DDTA). The multi-ple-input of the DDTA is realized using a multiple-input bulk-driven MOS transistor (MI-BD-MOST) technique to maintain a single differential pair, thereby achieving simple structure with minimal power consumption. In a single topology, the proposed filter can provide five standard filtering functions (low-pass, high-pass, band-pass, band-stop, and all-pass) in four modes: voltage (VM), current (CM), transadmittance (TAM), and transimpedance (TIM). This provides the full capability of a mixed mode filter (i.e., twenty filter functions). Moreover, the VM filter offers high-input and low-output impedances and the CM filter offers high-output impedance; therefore, no buffer circuit is needed. The natural frequency of all filtering functions can be electronically controlled by a setting current. The voltage supply is 0.5 V and for a 4 nA setting current, the power consumption of the filter was 281 nW. The filter is suitable for low-frequency biomedical and sensor applications that require extremely low supply voltages and nano-watt power consumption. For the VM low-pass filter, the dynamic range was 58.23 dB @ 1 % total harmonic distortion. The proposed filter was designed and simulated in the Cadence Virtuoso System Design Platform using the 0.18 µm TSMC CMOS technology.

Rainwater infiltration presents substantial challenges for urban wastewater management systems. This article delves into enhancing the quality of wastewater systems by proposing a novel device designed to tackle this issue comprehensively. The focal point of our research revolves around the conceptualization, construction, rigorous testing, and the potential multifaceted applications of this innovative wastewater device. Our study is dedicated to assessing the viability of a cutting-edge apparatus that empowers municipal entities in swiftly identifying rainwater ingress points within channels during precipitation events. Our findings vividly showcase the device's remarkable capability to directly measure moisture levels along the channel's path, eliminating the arduous need for manual data input, extensive data collection, and intricate water analysis procedures. To ensure the seamless flow of both sewage and water within the sewer channel, the use of a relatively slender strap is conventionally favored. However, factoring in the requisite structural robustness, we recommend a minimum thickness of 4 mm for 3D printing applications. For instances where maintaining the channel's cross-sectional area integrity is paramount, opting for a armlet with wet circuit measurement thickness of up to 7 mm is prudent. In the realm of material selection, our investigation advocates for the utilization of PC/ABS (polycarbonate/ Acrylonitrile Butadiene Styrene), ABS, ASA (Acrylonitrile Styrene Acrylate), or HIPS (High Impact Polystyrene) for the strap housing. For sewer diameters surpassing 315 mm, the application of thin-walled PVC (Poly Vinyl Chloride) emerges as a practical recommendation. Notably, the incorporation of PVC flat bars is discouraged, as their presence might potentially hinder the fluidity of sewage flow, thereby compromising the precision of wet circuit measurements. The pivotal innovation lies in the armlet with wet circuit measurement system, harboring immense potential for broad-scale integration across municipal facilities. This solution emerges as a streamlined and efficient strategy, offering a comprehensive avenue for continuously monitoring, fine-tuning, and optimizing the structural soundness and operational efficacy of sewer systems.

The main objective of this article was to evaluate the repercussions of the crises resulting from the COVID-19 pandemic and the war in Ukraine on changes in the European Union's reliance on energy raw material imports, particularly from Russia. Furthermore, several specific objectives were outlined: to ascertain the EU's energy balance and any alterations therein, to identify changes in the concentration of energy raw material imports among EU countries during the crises, to determine the level and fluctuations in energy raw material import dependence within the EU and individual member states throughout the crises, and lastly, to assess changes in the concentration of energy raw material imports from Russia in EU countries during the crises. The research encompassed all 27 EU Member States as of 31st December 2022, and the examination period spanned from 2010 to 2022. The information sources included relevant literature on the subject and data sourced from Eurostat. In conducting the analysis and presenting the data, several methodologies were employed, including descriptive, tabular, and graphical techniques. Additionally, quantitative measures such as the Gini structure concentration coefficient and concentration analysis through the Lorenz curve were utilized. During the COVID-19 pandemic, the EU experienced a slight reduction in dependence on energy raw material imports. However, this reduction was short-lived and mainly attributed to the decrease in energy demand caused by the pandemic. Conversely, the war in Ukraine had a substantial impact, leading to a notable surge in energy raw material imports as a result of stockpiling efforts and the need to safeguard against further disruptions in the energy market. Notably, the EU's reliance on energy imports from Russia was already considerable. Following the outbreak of the conflict in Ukraine, imports of oil, petroleum products, and solid fossil fuels experienced significant decline due to imposed sanctions. Nonetheless, restrictions on natural gas imports were comparatively less severe.

This publication describes the influence of residue monomers in synthesized pressure-sensitive adhesives based on acrylics on main performance such as tack, peel adhesion, shear strength and shrinkage in form of transfer tapes used for joining wooden elements in furniture industry. The discussed carrier-free adhesive tapes are synthesized by photo-crosslinking and photopolymerization with UV radiation of photoreactive prepolymers sandwiched between two adhesive siliconized polyester films. The simultaneous crosslinking and polymerization process under UV lamps carried out under UV lamps placed simultaneously above and below the crosslinked photoreactive polymer layer leads to the production of a carrier-free adhesive film. In this test series it were investigated to what how the intensity of UV radiation and the time of its exposure affect the viscosity of photoreactive compositions, and then the content of unreacted monomers in them and, subsequently, the method of their crosslinking and polymerization, and the concentration of the photoreactive crosslinking compound leading to the obtaining of transfer adhesive tapes, and thus on their tray, peel adhesion, shear strength and shrinkage on the surface of the wood.

The non-linear analysis of hollow-core concrete slabs requires the use of advanced numerical techniques, proper constitutive models both for concrete and steel as well as particular computational skills. If prestressing, cracking, crack opening, material softening, etc. are also to be taken into account, then the computational task can far exceed the capabilities of an ordinary engineer. In order for the calculations to be carried out in a traditional design office, simplified calculation methods are needed. Preferably based on the linear finite element (FE) method with a simple approach that takes into account material nonlinearities. In this paper the simplified analysis of hollow-core slabs based on the generalized nonlinear constitutive law is presented. In the proposed method a simple decomposition of the traditional iterative linear finite element analysis and the non-linear algebraic analysis of the plate cross-section is used. Through independent analysis of the plate cross-section in different deformation states, a degraded plate stiffness can be obtained, which allows iterative update of displacements and rotations in the nodes of the FE model. Which in turn allows to update the deformation state and then correct translations and rotations in the nodes again. The results obtained from the full detailed 3D nonlinear FEM model and from the proposed approach are compared for different slab cross-sections. The obtained results from both models are consistent.

The paper presents design methodology for the production process of a new product from the point of view of the assembly operations technology criterion (Design for Assembly - DFA) in the conditions of high-volume production. Mentioned are DFA methods and techniques used in the implementation of a new product. Author presents a new method to assess design for manufacturability based on fuzzy variables based on fuzzy variables. An example was given to illustrate the proposed course of action

Exhaled breath condensate (EBC) sample analysis is an entirely non-invasive novel sample collection method that is fast, easy to perform, and effort-appeared independent. EBC samples can be very useful in identifying the biomarkers of many diseases. This review provides an updated overview of EBC pH disturbances in different disorders as well as physiological levels among healthy individuals since 2012. Our meta-analysis addresses some of the key questions related to sample processing before pH measurement and discusses various methods of condensate standardization that can be employed prior to conducting a pH assay. Given the recent widespread interest in research into the use of EBC to identify biomarkers, it is necessary to establish a pathway leading from analytical methods for biomarker evaluation using EBC pH to clinical applications of this technology. This review fills a gap in the literature and attempts to connect theory to practical analytical approaches to analyzing EBC samples and making critical treatment-related decisions next to the patient's bed.

Current industrial trends bring new challenges in energy absorbing systems. Polymer materials as the traditional packaging material seem to be promising due to their low weight, structure and production price. Based on the review, the linear low-density polyethylene material was identified as the most promising material for absorbing impact energy. The current paper addresses the identification of the material parameters and the development of a Constitutive material model to be used in future design by virtual prototyping. The paper deals with the experimental measurement of the stress-strain relations of the linear low-density polyethylene under static and dynamic loading. The quasi-static measurement is realized in two perpendicular principal directions and is supplemented by a test measurement in the 45 degrees direction, i.e. exactly between the principal directions. The quasi-static stress-strain curves are analyzed as an initial step for dynamic strain rate dependent material behavior. The dynamic response is tested in the drop tower using a spherical impactor hitting the flat material multi-layered specimen at two different energy levels. The strain rate dependent material model is identified by optimizing the static material response obtained in the dynamic experiments. The material model is validated by the virtual reconstruction of the experiments and by comparing the numerical results to the experimental ones.

During the bioassay, on leaf sections of the A. roylei species, a significantly higher number of T. tabaci females was recorded compared to the cv. Tęcza of the A. cepa species and the cv. Kroll of the A. fistulosum species, in each observation period. Significantly more thrips settled on cv. Kroll compared to Alibaba and Bila. Regarding the results obtained on A. cepa, significantly fewer females were found on cv. Bila compared to cv. Tęcza. Opposite results were observed in a combination of cvs. Tęcza - Alibaba, where significantly more insects settled on leaves of cv. Alibaba. Statistically significant differences of cultivars/species were found in the number of hatched larvae on the leaves of the tested cultivars/species of onion. The significantly lowest number of larvae hatched from eggs laid on A. roylei compared to A. fistulosum and cultivars of A. cepa, except for Bila.

Employing numerical methods to simulate manufacturing processes and study their influential factors is increasing. The development of computers and engineering software has increased the ability and accuracy of numerical methods in simulating various aspects of different processes. One of the manufacturing processes that has been considered by many industries in recent years to join metals in solid-state with unique properties is called friction stir welding. It is challenging and, in some cases, impossible to experimentally study the various aspects of this process, such as temperature distribution, stress distribution, and material flow, due to severe plastic deformation in the weld zone. In this case, numerical methods are used to investigate these parameters and better understand the process. This study first investigates various numerical methods researchers use to simulate the process. The ability, pros, and cons of these methods to simulate the process are also examined. Then, the applications of numerical models in simulating the temperature distribution during the process as well as the effects of input parameters on the temperature history of the process, are deeply considered. Next, the application of numerical methods in material flow modeling during the process is investigated. Finally, the modeling of the microstructure of the welding zone is investigated using numerical methods that help significantly in predicting the weld microstructure.

Nanostructured anodic oxide layers on an FeAl₃ intermetallic alloy were prepared by two-step anodization in 20 wt.% H2SO4 at 0°C. The voltage range was 10.0 – 22.5 V with a step of 2.5 V. The structural and morphological characterizations of the received anodic oxide layers were performed by FE-SEM. Therefore, the formed anodic oxide was found to be highly porous with a high surface area, as indicated by the FE-SEM studies. It has been shown that the morphology of fabricated nanoporous oxide layers is strongly affected by the anodization potential. The oxide growth rate first increased slowly (from 0.010 μm/s for 10 V to 0.02 μm/s for 15 V) and then very rapidly (from 0.04 μm/s for 17.5 V up to 0.13 μm/s for 22.5 V). The same trend was observed for the change in the oxide thickness. Moreover, for all investigated anodizing voltages, the structural features of the anodic oxide layers, such as the pore diameter and interpore distance, increase with increasing anodizing potential. The obtained anodic oxide layer was identified as a crystalline FeAl₂O₄, Fe₂O₃ and Al₂O₃ oxide mixture.

This study explores the Edaravone solubility space encompassing both neat and binary dissolution media. The efforts were made toward revealing the concentration limits inherently associated with common pure and mixed solvents. For this purpose, the published solubility data of the title drug were scrupulously inspected and cured. This enabled to make the dataset consistent and coherent. However, the lack of some important types of solvents in the collection called for an extension of the available pool of Edaravone solubility data. Hence, new measurements were performed for collecting Edaravone solubility in polar non-protic and polar di-protic media. Such an extended set of data was used for tuning the parameters of regressors models and formulating the ensemble for predicting new data. In both phases, namely the model training and ensemble formulation, close attention was paid not only to minimizing the deviation of computed values from the experimental ones but also to ensuring the high predictive power and computing solubility for new systems. Furthermore, the environmental friendliness characteristics determined based on the common green solvent selection criteria was included in the analysis. Our applied protocol led to the conclusion that the solubility space defined by ordinary solvents is limited, and it is unlikely to find solvents that are more suited for Edaravone dissolution than those depicted in this manuscript. The theoretical framework presented in this study provides a precise guide for conducting experiments, saving time and resources in the pursuit of new findings.

Fusarium head blight (FHB) is a wheat disease caused by fungi of the genus Fusarium. The aim of the study was to find relationships between the weather conditions in the experimental years and the locations and the amount of F. culmorum DNA and trichothecene genotypes, as well as the proportions between them. A three-year field experiment (2017, 2018 and 2019) was established at two locations (Poznań, Radzików). F. culmorum DNA was detected in all grain samples in an average amount of 20124 pg per 1 g of wheat DNA. The average amount of DNA from the 3ADON genotype was 4879 pg/μg and the amount of DNA from the NIV genotype was 3330 pg/μg. In the three experimental years, a large variability was observed in the coefficients of correlation between DNA concentrations and the FHB index, FDK, ergosterol, and the corresponding toxins. There were significant correlations between disease incidence, fungal biomass (quantified as the total amount of fungal DNA or DNA trichothecene genotypes) and toxins (DON, 3AcDON and NIV) concentrations. The 3ADON trichothecene genotype dominates over the NIV genotype (ratio 1.5); however, this varied greatly depending on environmental conditions.

Radiotherapy and cisplatin-based chemotherapy belong to the main treatment modalities for head and neck squamous cell carcinoma (HNSCC), and induce cancer cell death by generating DNA damage, including the most severe double strand breaks (DSBs). Alterations in DSB response and repair genes may affect individual DNA repair capacity and treatment sensitivity, contributing to therapy resistance and poor prognosis often observed in HNSCC. In this study, we investigated the association of a panel of single nucleotide polymorphisms (SNPs) in 20 DSB signaling and repair genes with therapy results and prognosis in 505 HNSCC patients treated non-surgically with DNA damage-inducing therapies. In the multivariate analysis, there were a total of 14 variants associated with overall, locoregional recurrence-free or metastasis-free survival. Moreover, we identified 10 of these SNPs as independent predictors of therapy failure and unfavorable prognosis in the whole group or in two treatment subgroups. They were MRE11A rs2155209, XRCC5 rs828907, RAD51 rs1801321, rs12593359, LIG4 rs1805388, CHEK1 rs558351, TP53 rs1042522, ATM rs1801516, XRCC6 rs2267437 and NBS1 rs2735383. Only CHEK1 rs558351 remained statistically significant after correction for multiple testing. These results suggest that specific germline variants related to DSB response and repair may be potential genetic modifiers of therapy effects and disease progression in HNSCC treated with radiotherapy and cisplatin-based chemoradiation.

The purpose of this article is to present the COVID-19 pandemic disruptions occurring in the supply chain of automotive companies, taking into account the type of business. The specific objectives are: to identify and characterise the types of enterprises operating in automotive supply chains, to identify changes during the pandemic in automotive enterprises, depending on the type of activity, to show disruptions in automotive supply chains and ways to counteract these disadvantages depending on the type of activity. Automotive enterprises operating in Poland were selected for the study purposefully. A random selection method was used to select 500 automotive companies for the study. The data sources were surveys conducted in June 2023 among 500 enterprises in the form of a face-to-face telephone interview. Automotive companies experienced supply chain disruptions, regardless of the type of business. Most often, these were caused by lockdowns and official closures, low stocks of materials and products, and problems with employees. There was no difference by type of business. Disruptions were most often short-lived, up to 1 year. Companies countered disruptions by using mostly operational measures, which were short-lived. Only a small percentage of operators made strategic decisions and countered disruptions over a longer period. The scale of these actions was greater among manufacturers than among dealers and car service companies.

Currently, the district heating (DH) in Poland is facing many challenges. The business model used hitherto was very simple—in most cities, heating plants produced heat, and centralized heating systems supplied the "product" at a price approved annually by the president of the Energy Regulatory Office (URE). However, recent years have brought significant changes on the market. EU regulations force the elimination of old coal-fired plants that were still built in the Polish People's Republic (PRL), moreover, high prices of CO2 emission allowances aggravate the financial situation of companies. In addition, in the heating sector, the trend observed in the power sector is becoming increasingly visible—limiting the role of large sources in favor of energy generated locally, closer to the customer. One of the biggest challenges is achieving the targets set by the EU for the share of renewable energy sources (RES) in the heating sector. The war in Ukraine and problems with the supply of coal and gas are an additional impulse to turn to RES. Thus, the development of sustainable and innovative solutions for energy production and supply at the level of urban networks is currently one of the main technical challenges. The purpose of the paper is to present the current situation and perspectives of development of district heating systems in Poland with a view to the status of district heating in the world, and some deeper insight into European conditions. The review presents energy sources with particular emphasis on renewable energy sources (RES) and their cogeneration for heat production. The examples of existing heating network solutions using renewable energy sources, based on the selected published case studies, are also discussed.

The standard edge crush test (ECT) allows to determine the crushing strength of the corrugated cardboard. Unfortunately, this test cannot be used to estimate the compressive stiffness, which is an equally important parameter. It is because, any attempt to determine this parameter using current lab equipment quickly ends in a fiasco. The biggest obstacle is obtaining a reliable measurement of displacements and strains in the corrugated cardboard sample. In this paper, we present a method that not only allows to reliably identify the stiffness in the loaded direction of orthotropy in the corrugated board sample, but also the full orthotropic material stiffness matrix. The proposed method uses two samples: (a) traditional, cut crosswise to the wave direction of the corrugated core, and (b) cut at an angle of 45 degrees. Additionally, in both cases, an optical system with digital image correlation (DIC) is used to measure the displacements and strains on the outer surface of samples. The use of a non-contact measuring system allows to avoid using the measurement of displacements from the crosshead, which is burdened with a large error. Apart from the new experimental configuration, the article also proposes a simple algorithm to quickly characterize all sought stiffness parameters. The obtained results are finally compared with the results obtained in the homogenization procedure of the cross-section of the corrugated board. The results were consistent in both cases.

In the modern world, all manufacturers strive for the optimal design of their products. This general trend is recently also observed in the corrugated board packaging industry. Colorful prints on displays, perforations in shelf-ready-packaging and various types of ventilation holes in trays, although extremely important for ergonomic or functional reasons, weaken the strength of the box. To meet the requirements of customers and recipients, packaging manufacturers outdo each other in new ideas for the construction of their products. Often the aesthetic qualities of the product become more important than the attention to maintaining the standards of the load capacity of the packaging (which, apart from their attention-grabbing functions, are also intended to protect transported products). The particular flaps design (both top and bottom) and their influence on the strength of the box is investigated in this study. The updated analytical-numerical approach is used here to predict the strength of the packaging with various flap’s offsets. Experimental results indicated a significant decrease in the static load-bearing capacity of packaging in the case of shifted flap creases. The simulation model proposed in our previous work has been modified and updated to take into account also this effect. The results obtained by the model presented in the paper are in satisfactory agreement with the experimental data.

The corrugated board packaging industry is increasingly using advanced numerical tools to design and estimate the load capacity of its products. That is why numerical analyzes are becoming a common standard in this branch of manufacturing. Such trend causes either the use of advanced computational models that take into account the full 3D geometry of the flat and wavy layers of corrugated board, or the use of homogenization techniques to simplify the numerical model. The article presents theoretical considerations that extend the numerical homogenization technique already presented in our previous work. The proposed here homogenization procedure also takes into account the creasing and / or perforation of corrugated board, i.e. processes that undoubtedly weaken the stiffness and strength of the corrugated board locally. However, it is not always easy to estimate how exactly these processes affect the bending or torsional stiffness. What is known for sure is that the degradation of stiffness depends, among other things, on the type of cut, its shape, the depth of creasing, as well as their position or direction in relation to the corrugation direction. The method proposed here can be successfully applied to model smeared degradation in a finite element or to define degraded interface stiffnesses on a crease line or a perforation line.

The need for quick and easy deflection calculations of various prefabricated slabs causes that simplified procedures and numerical tools are used more and more often. Modelling of full 3D finite element (FE) geometry of such plates is not only uneconomical but often requires the use of complex software and advanced numerical knowledge. Therefore, numerical homogenization is an excellent tool, which can be easily employed to simplify a model, especially when accurate modelling is not necessary. Homogenization allows for simplifying a computational model and replacing a complicated composite structure with a homogeneous plate. Here, a numerical homogenization method based on strain energy equivalence is derived. Using the method proposed, the structure of the prefabricated concrete slabs reinforced with steel spatial trusses is homogenized to a single plate element with an effective stiffness. There is a complete equivalence between the full 3D FE model built with solid elements combined with truss structural elements and the simplified homogenized plate FE model. The method allows for the correct homogenization of any complex composite structures made of both solid and structural elements, without the need to perform advanced numerical analyses. The only requirement is a correctly formulated stiffness matrix of a representative volume element (RVE) and appropriate formulation of the transformation between kinematic constrains on RVE boundary and generalized strains.

Intersectoral and intermunicipal cooperation are still underdeveloped spheres of public and economic development policies. Academic discussions are invariably focused on pro-competitive activities, the economic efficiency of which is not always sufficient. In this paper the authors attempt to identify factors leading to cooperation between local government authorities and economic entities, focusing on examples from the forest and wood-based sector in Poland. These processes are analysed in the framework of the New Institutional Economy, both in the theoretical and practical context.

Clew Bay is an important aquaculture production area in Ireland. In this study, we focused on a high-resolution simulation of the Clew Bay region based on a Regional Ocean Modelling System (ROMS). Freshwater discharges from eight rivers are included in the model and a wetting-drying scheme has been implemented. The Clew Bay model simulation was validated and calibrated with available observations (e.g., Acoustic Doppler Current Profilers (ADCP), vertical salinity and temperature profiles and tide gauge) in the geographic area of the model domain. High correlations were found between the model outputs and observed temperature, salinity and tide gauge water levels along with small Root Mean Square Errors. This indicates that the model was able to reproduce the oceanographic phenomena in the study area. The Taylor diagram analysis showed a high correlation coefficient (R=0.99) between the ADCP bottom temperature in the Inner Bay and the Clew Bay model, along with a small Centered Root Mean Square Error (RMSD =0.5 ◦ C). High correlation coefficients (R &gt; 0.80) were found between the model and the two ADCPs for the zonal current component. There was a resemblance in structure between the model and the observed salinity profiles, indicating that freshwater was correctly implemented in the model. Moreover, the correlation coefficient between the model and the tidal sea surface height (SSH) was 0.99, with an RMSD of 0.09 m. We discovered that wind direction and speed have a significant impact on the bay's water inflow rate. The model outputs can be used to provide scientists, fishermen and decision-makers with hydrodynamic information on ocean conditions in the bay.

Laser-induced breakdown spectroscopy (LIBS) is an important analysis technique with applications in many industrial branches and fields of scientific research. Nowadays, the advantages of LIBS are impaired by the main drawback in the analysis of collected data. This procedure is essentially based on the comparison of lines present in the spectrum with a literature database. This paper proposes the use of various computational intelligence methods to develop a reliable and fast classification of non-destructively acquired LIBS spectra into a set of predefined classes. We focus on a specific problem of classification of paper-ink samples into 30 separate, predefined classes. For each of 30 classes (10 pens of each of 5 ink types combined with 10 sheets of 5 paper types plus empty pages) 100 LIBS spectra are collected. Four variants of preprocessing, seven classifiers (Decision trees, Random forest, k-Nearest Neighbour, Support Vector Machine, Probabilistic Neural Network, Multi-Layer Perceptron, and Generalized Regression Neural Network), 5-fold stratified cross-validation and test on an independent set (for methods evaluation) scenarios are employed. Our developed system yielded an accuracy of 99.08% with average classification time of about 0.12 s is obtained using the random forest classifier. Our results clearly demonstrates that machine learning methods can be used to identify the paper-ink samples based on LIBS reliably at a faster rate.

Alternative fuels containing biocomponents produced in various technologies are introduced in aviation to reduce its carbon footprint but there is little data describing their impact on the performance and emissions of engines. The purpose of the work is to compare the performance and gas emissions produced from two different jet engines: the GTM-140 microturbine and the full-size DGEN380 turbofan, powered by blends of Jet A-1 and one of two biocomponents: 1) ATJ and 2) HEFA produced from used cooking oil (UCO) in various concentrations. The acquired data will be used to develop an engine emissivity model to predict gas emissions. Blends of the mineral fuel with synthetic components were prepared in various concentrations, and their physicochemical parameters were examined in the laboratory. Measurements of emissions from both engines were carried out in selected operating points using the Semtech DS gaseous analyzer and the EEPS spectrometer. The impact of tested blends on engine operating parameters is limited, and their use does not carry the risk of a significant decrease in aircraft performance or increase in fuel consumption. Increasing the content of biocomponents causes a noticeable rise in the emission of CO and slight increase for some other gasses (HC and NOx), which should not, however, worsen the working conditions of the ground personnel. This implies that there are no contraindications against using tested blends for fuelling gas-turbine engines.

The paper presents research results on biocomposites made from a combination of extruded apple pomace (EAP) and potato starch (SP). The products were manufactured by hot pressing using a hydraulic press with a mold for producing samples. The prepared biocomposites were subjected to strength tests, surface wettability was determined and color analysis was carried out. Thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FTIR) and cross section observed in Scanning electron microscope (SEM) were also performed. The obtained test results showed that the combination of apple pomace (EAP) and starch (SP) enabled the production of compact bicomposite materials. At the same time, it was found that each increase in the share of starch in the mixture for producing biocomposites increased the strength parameters of the obtained materials. With the highest share of starch in the mixture, 40%, and a raw material moisture content of 14%, the material had the best strength parameters and was even characterized by hydrophobic properties. It was also found that materials with a high content of starch are characterized by increased temperature resistance. Analysis of SEM microscopic photos showed well-glued particles of apple pomace, pectin, gelatinized starch and a smooth external structure of the samples. Research and analyzes have shown that apple pomace reinforced only with the addition of starch can be a promising raw material for the production of simple, biodegradable biocomposite materials.

Mitochondrial dysfunction has been linked to psoriasis, and may be an important underlying factor contributing to this disease. However, a precise methodology for assessing mitochondrial dysfunction has yet to be developed. One promising approach is to measure NADH autofluorescence from affected skin areas. In this study, we show that Flow Mediated Skin Fluorescence (FMSF) can be used for non-invasive assessment of mitochondrial dysfunction in psoriasis. The fluorescence level at baseline and the half-time of ischemic growth (t1/2) derived from the FMSF traces can be used for non-invasive assessment of NADH/NAD+ redox imbalance in psoriatic lesions compared to unaffected skin. These results are supported by analysis of the key FMSF parameters, Reactive Hyperemia Response (RHR) and Hypoxia Sensitivity (HS). This method not only contributes to understanding of the biochemical processes involved in the etiopathogenesis of psoriasis, but also provides a basis for identifying new drug targets and improving the treatment process.

In the laboratory practice, several standards for testing the bending stiffness of corrugated board are used. There are often cases of tests where the results depend on the way the sample is placed on the supports. The problem arises when the board is five-ply (with two corrugated layers with different corrugation heights) or when the board has asymmetrically selected papers on the flat layers. In this article, we focus our attention on the problem related to boundary conditions, with particular attention to the local effects of the support of the sample. Since the cardboard layers, both flat and corrugated, have a small thickness, a slight deformation of the papers can always be observed at the point of contact between the sample and the support, which affects the readings of the measured stiffness. The paper presents theoretical and numerical analyzes showing how much the method of supporting the sample affects the measured bending stiffness of various samples. Numerical observations were also compared with the results of analyzes presented by other scientists as well as with experimental results.

The advancement in the production and usage of the cerium oxide nanoparticles have diverted the attention of scientists towards their usage in medical field and therapeutic usage. The clinical usage of these Nano ceria is based on their ability to moderate the oxidative stress and this is only because of their ability to change their valent state from +3 to +4 which makes them ideal for scavenging radicals for use in a number of systemic and neurodegenerative disorders. This review aims to synthesize the basic methods used for the synthesis of nanoparticles along with the use of ligand, stabilizing agent and other components. This review also concludes that how various physical and chemical properties of nanoparticles effect the basic biological activities such as antimicrobial activity, cytotoxicity and many others. However, during the standardization, some of the physiochemical properties, methods used for preparation and catalytic abilities must be taken into account.

Fusarium head blight (FHB) can cause contamination of cereal grain with mycotoxins. Triticale is also infected with FHB; however, it is more resistant than wheat to head infection. The aim of this study was to identify triticale lines that combine low head infection with low toxin contamination. Resistance to FHB of 15 winter triticale and three winter wheat lines was evaluated over a three-year experiment established in two locations. At the anthesis stage, heads were inoculated with Fusarium culmorum isolates. The FHB index was scored and the percentage of Fusarium-damaged kernels (FDKs) assessed. The grain was analysed for type B trichothecenes (deoxynivalenol and derivatives, nivalenol) and zearalenone content. The average FHB index was 10.7%. The proportion of FDK was 18.1% (weight) and 21.6% (number). An average content of deoxynivalenol for wheat amounted to 7.258 mg/kg and nivalenol to 5.267 mg/kg. In total, it was 12.788 m/kg of type B trichothecenes. The zearalenone content in the grain was 0.805 mg/kg. Relationships between FHB index, FDK and mycotoxin contents were statistically significant for triticale lines; however, they were stronger for FDK versus mycotoxins. Lines combing all types of FHB resistance were found, and two of them had resistance similar to that of wheat lines with the Fhb1 gene.

Regulation of the diet in terms of the content of soluble and insoluble fibre is of great importance from the point of view of dietetics, microbiology of the gastrointestinal tract and immunology of the organism. Dietary fibre plays an important role in maintaining the balance between the con-tinuity of gut mucus production (intestinal mucosa), the stability of the intestinal microbiome composition, the regeneration of the intestinal epithelium and the immune status within the gut-associated lymphoid tissue (GALT) are played by pectin and their metabolic products in the form of pectin oligosaccharides. The main purpose of this review was to focus on pectin, their functions, their impact on the human's health and on some of the most promising prebiotics due to their solubility in the gastrointestinal tract in the form of pectin oligosaccharides. They have the properties of pectin, but have also additional features and postbiotics obtained in fermentation process can affect the intestinal microbiome and GALT-related immunity. They can be obtained from plant agro-wastes.

Comparisons of power flows and efficiencies in two structurally quite similar cylindrical series-parallel planetary gear systems (PGSs) were performed in three separate parts of this paper. Each of these single degree of freedom (DoF) systems consists of three different 2KH subsystems connected in series-parallel. The main goal was to prove that apart from complex, structurally and dynamically coupled PGSs, there are also complex and only structurally coupled PGSs, in which the phenomenon of power flow circulation inside closed loops does not occur. Such a half-coupled type of PGS is herein called pseudo-coupled. Therefore, Part I discusses in detail the geometry, kinematics and statics of coupled PGSs in order to determine power flow paths. A comparison of the directions of power flow in both types of PGSs can be made in Part II after determining the power flow paths in the second planetary gear in a similar way. The directions of power flow in both types of PGSs were determined in a relatively simple way, thanks to the distinction between active and passive torques and thus active and passive shafts of individual subsystems. The efficiency comparison made in Part III will show whether power circulation has an influence on the efficiency value, at least in these two types of PGSs.

The Covid-19 pandemic has forced the transfer of local government public ser-vices to the virtual world. Remote handling of matters in government offices has be-come the norm rather than the exception. The 2016 EU directive on public sector web-sites and mobile applications and the 2019 European Digital Accessibility Act made it mandatory that these services be provided electronically and accessible to people with disabilities. The purpose of the study conducted by the authors was to determine whether the Covid-19 pandemic resulted in the implementation of European solutions in the Polish legal order and whether this implementation resulted in the actual adap-tation of digital activities of local government units (LGUs) to the needs of people with disabilities. The research was conducted in Q4 2022 in two trial formats: 1. In the form of a survey (about 250 LGUs), which covered compliance with for-mal requirements, the level of readiness of the officials to create digitally accessible documents and content, and organizational readiness of the offices. 2. In the form of an analysis of the source code of the websites of 66 Polish cities with county rights - due to the availability of results of the same sample from 2015. The completed research showed that the LGUs in Poland: 1. met the formal and organizational requirements for digital accessibility, 2. did not make the necessary efforts to prepare employees to create digitally ac-cessible documents and content, 3. the surveyed websites had inferior source code in terms of meeting the WCAG standard in 2022 than in 2015. It seems reasonable to conclude that the Covid-19 pandemic had a formal, rather than real, impact on the digital accessibility of services provided by Polish LGUs.

The impact of cyclic heat stress (CHS) and lighting events on pig feeding behavior (FB) was investigated. The FB of 90 gilts was recorded in real time under two ambient temperatures (AT): thermoneutrality (TN, 22 °C) or CHS (22°/35 °C). The day was divided into four periods: PI (06-08 h); PII (08-18 h); PIII (18-20 h); and PIV (20-06 h). Automatic and Intelligent Precision Feeders recorded each feed event for each pig. An estimated meal criterion (49 minutes) was used to calculate the FB variables. Feed behavior in both ATs followed a circadian pattern. The CHS reduced the feed intake by 6.9%. Pigs prioritized feed intake during the coolest hours of the day; however, nocturnal cooling did not allow the pigs to compensate for the reduced meal size due to CHS. The highest meal size and most of the meals were observed during the lighting-on period. Pigs reduced their interval between meals during periods II and III. The lighting program increased the meal size when the lights were switched on and reduced the meal size when the lights were switched off. Thus, the dynamics of the FB were largely influenced by AT, while the meal size was affected by the lighting program.

Overhydration (OH) is a prevalent medical problem occuring in patients with kidney failure, but a specific marker has still not been found. Currently, clinicians employ techniques such as bioimpedance spectroscopy (BIS), ultrasound (US) markers of fluid overload or markers of heart and kidney function such as NT-pro-BNP, GFR or creatinine levels. New serum markers, including but not limited to Ca-125, Galectin-3 (Gal-3), Adrenomedullin (AMD) and Urocortin-2 (UCN-2), are presently under research, displaying promising results. The necessity to ascertain a more precise marker of overhydration is urgent mainly because physical examination is exceptionally imprecise. Signs and symptoms of fluid overload, like edema or gradual increase of body mass, are not always present, notably in patients with chronic kidney disease. This review paper summarizes actual knowledge of a patient's hydration status estimation, focusing specifically on kidney diseases.

Growing acreage and changing consumer preferences cause increasing interest in the cereal products originating from organic farming. Lack of results of objective test, however, does not allow drawing conclusions about the effects of cultivation in the organic system and comparison to currently preferred conventional system. Field experiment was conducted in organic and conventional fields. Thirty modern cultivars of winter wheat were sown. They were characterized for disease infection including Fusarium head blight, seed sowing value, the amount of DNA of the six species of Fusarium fungi as well as concentration of ergosterol and trichothecenes in grain. The intensity Fusarium head blight was at a similar level in both systems. However, Fusarium colonization of kernels expressed as ergosterol level or DNA concentration was higher for the organic system. It did not reflect in an increased accumulation of trichothecenes in grain, which was similar in both systems, but sowing value of organically produced seeds was lower. Significant differences between analyzed cropping systems and experimental variants were found. The selection of the individual cultivars for organic growing in terms of resistance to diseases and contamination of grain with Fusarium toxins was possible. Effects of organic growing differ significantly from the conventional and grain obtained such way can be recommended to consumers. There are indications for use of particular cultivars bred for conventional agriculture in the case of organic farming, and the growing organic decreases plant stress resulting from intense fertilization and chemical plant protection.

This article presents research on selected materials with the aim of determining their rare earth element (REE) content and attempting to intensify it. The test material was coal slurry, which is a waste product from the operation of a preparation plant of a closed coal mine. Research on REE concentration intensification tests was carried out using magnetic separation. Laboratory analyses determining the REE content in the samples obtained, were carried out using the inductively coupled plasma ionisation mass spectrometry (ICP-MS) technique. Carrying out this research by the KOMAG Institute of Mining Technology, is a continuation of work related to making mining waste economically useful and determining a new source of REE recovery. Previous research and development work showed REE content (scandium 40.49 ppm) in the coal slurries studied. The result of the work carried out is the determination of the economic utility of REE recovery from the studied waste.

Current microbiological methods for pneumonia diagnosis require invasive specimen collection and time-consuming analytical procedures. There is a need for less invasive and faster methods to detect lower respiratory tract infection. The analysis of volatile metabolites excreted by pathogenic microorganisms provides the basis for developing such a method. Given the synergistic role of Candida albicans in increasing the virulence of pathogenic bacteria causing pneumonia and the cross-kingdom metabolic interactions between microorganisms, we compare the emission of volatiles from Candida albicans yeasts and the bacteria Staphylococcus aureus using single and mixed co-cultures and apply that knowledge to human in vivo investigations. Gas-chromatography-mass spectrometry (GC-MS) analysis resulted in the identification of sixty-eight volatiles that were found to have significantly different levels in cultures compared to reference medium samples. Certain volatiles found in co-culture originated mainly from C. albicans metabolism (e.g., isobutyl acetate), whereas other volatiles primarily came from S. aureus (e.g., ethyl 2-methylbutyrate). Isopentyl valerate reflects synergic interactions of both microbes, as its level in co-cultures was found to be approximately three times higher than the sum of its amounts in monocultures. Hydrophilic-lipophilic balanced (HLB) coated meshes for thin-film microextraction (TFME) were used to pre-concentrate volatiles directly from bronchoalveolar lavage (BAL) specimens collected from patients suffering from ventilation-associated pneumonia (VAP) that was caused explicitly by C. albicans and S. aureus. GC-MS analyses confirmed the existence of in vitro-elucidated microbial VOCs in human specimens. Significant differences in BAL-extracted amounts respective to the pathogen causing pneumonia were found. The model in vitro experiments provided evidence that cross-kingdom interactions between pathogenic microorganisms affect the synthesis of the volatile compounds. The TFME meshes coated with HLB particles proved to be suitable for extracting VOCs from human material, enabling the translation of in vitro experiments on the microbial volatilome to the in vivo situation involving infected patients. This indicates the direction that should be taken for further clinical studies on VAP diagnosis based on volatile analysis.

The issue of equipment layout in multi-floor satellites consists of two primary parts: allocating the equipment to the satellite's layers and placing the equipment in each layer individually. In reviewing the past literature in this field, firstly, the issue of assigning equipment to layers is observed in a few articles and next in the layout part, the non-overlapping constraint has always been a challenge, particularly for components that do not have a circular cross-section. In addition to presenting a heuristic method for allocating equipment to different layers of the satellite, this article presents a robust flexible programming model (RFPM) for the placement of equipment at different layers, taking into account the inherent flexibility of the equipment in placement and the subject of uncertainty. This model is based on the existing uncertainty between the distances of cuboid equipment which has not been addressed in any of the previous research, and by comparing its outputs with cases from past studies, it demonstrates a significantly higher efficiency in placing the equipment and meeting the limit of non-overlapping constraints between the equipment. Finally, it would be possible to reduce the design time in the conceptual and preparatory stages, as well as the satellite's overall size, while still satisfying other constraints like stability and thermal limitations, moments of inertia and centre of gravity.

Nanowater (NW-water declusterized in the cold plasma generator) can potentially ameliorate ram semen quality after freezing. Eighteen ejaculates from six Olkuska rams were divided into six equal portions each, and then diluted (800 × 106 spermatozoa/ml) and frozen in the fructose-skimmed milk-egg yolk Kareta extender containing 3% or 7% of glycerol (C3% and C7%) and diluted in deionized water (DW) or NW declusterized for 15 min (NW15)’ or 30 min (NW30’). All frozen-thawed semen samples were subjected to standard evaluation. In addition, ex situ survival time of spermatozoa was measured, and the proportions of apoptotic, necrotic and live sperm were determined by flow cytometry. The percentage of spermatozoa with mid-piece defects was lower (p &lt; 0.05) in NW15’-3% compared with C3%. The mean survival time of spermatozoa was greater (p &lt; 0.05) in NW30’ extenders compared with their respective controls. The proportion of necrotic spermatozoa 1 h after thawing was greater (p &lt; 0.05) in C7% compared with NW30’-7%, whereas the proportion of live cells detected immediately and 1 h after thawing were greater (p &lt; 0.05) in NW30’-7% than in C7%. NW enhanced cryoprotective effects of glycerol-containing extenders with an overall increase in sperm survivability being greater with 7% than 3% of glycerol.

This work compares the multi-element analysis of human hair and nails using inductively coupled plasma mass spectrometry (ICP-MS) with an easy, fast, cheap, non-destructive method using energy dispersive x-ray fluorescence (EDX-RF). The ICP-MS-based method was more sensitive (over 30 elements could be quantified) and costly (requiring more time, sample, and chemicals). The EDX-based method required laboratory and certified reference materials made of hair for instrument calibration. It was less sensitive (16 elements could be quantified: S, Si, Ca, Br, Fe, Cu, Cr, Mg, Si, K, Mn, Ni, Zn, Se, Sr, Pb), but it allowed to replace troublesome grinding with the dissolution of keratin-based material with alkalic agent (tetramethylammonium hydroxide, TMAH) and formation of stable for days pellets. The method is simple, enables automation, and, due to the modification of wells in the autosampler of the EDX system by immersion of home-designed inserts, it requires smaller amounts of biological material and binder (down to 70 mg instead of 500 mg required by commercially available instrument) to perform analysis. It was concluded that the EDX-based method offers complementary selectivity and sensitivity to ICP-MS with the possibility of the reuse of the sample for further analysis.

Recently, Electric Two-Wheelers ETW are changing the face of the global automotive market. This study focused on selecting proper material and mechanical isolation gap to design a protective enclosure for the battery pack of ETW. The integration of the Failure, Modes, Mechanism and Effect Analysis (FMMEA) method is utilized to develop the interface matrix and the severity index of different components of the enclosure. By analyzing different forces from the road conditions, dynamics during turn, acceleration, and deceleration with the enclosure, it becomes a crucial load-bearing element. Employing Finite Element Modeling (FEM), structural strength using materials like AL6061, Q235, C22000, DC 01 and Teflon are assessed under varying static, dynamic and thermal conditions. Modal analysis is conducted to observe the excitation frequencies where the maximum deformation for the metal enclosure is observed beyond 500Hz. AL6061 material that can withstand the stresses and deformations that are under allowable stress limits with negligible deformation is most preferable material based on the results. Minimal of 2.5 mm gap to be provided in case of metal casing and 10mm in case of Teflon is proven.

The growth of plant and process of yield formation in crops are moderated by surrounding conditions as well as interaction of genetic background of plants and environment. In the last two decades significant changes in climate can be observed generating unfavorable and harmful impact on plant development. Drought stress can be considered as one of the most dangerous environmental factor influencing plant life cycle and decreasing production of biomass and finally the yield. Plants can react to water deficit in a wide degree what is dependent on the species, the genetic variability within the species, the phase of the plant ontogenesis, the intensity of stress, and other potential stress factors. In plants there can be observed hybrids between distinct taxa which exhibit certain traits adopted to tolerate stress conditions better than parental plants. Oat × maize addition (OMA) plants are good example of fertile hybrids with retained maize chromosomes as addition to complete oat genome. Hybrids generated via wide crossing can exhibit morphological, physiological and biochemical variations implemented by the occurrence of extra chromosomes of maize, as well as interaction of maize and oat chromatin. The molecular analysis indicated 12.5% OMA lines among all tested descendants of wide oat-maize crossing. On the fourteenth day of the drought, a significant effect of stress on the content of soluble sugars and phenolic compounds was observed, soil drought significantly reduced plant biomass above ground and several yield components. Less water lost revealed by results of the excised leaf water loss test was correlated with high yield of OMA lines. Phenolic compounds content might be used as biochemical indicator of plant drought tolerance since there were significant correlation with high kernel yields of plants subjected to drought stress.

(1) Background: The goal of our study was to identify SNPs, metabolic pathways (KEGG), and gene ontology (GO) terms significantly associated with calving and workability; (2) Methods: Based on the EuroGenomics reference data set, we analyzed direct (DCE) and maternal (MCE) calving ease, direct (DSB), and maternal (MSB) stillbirth, milking speed (MSP), and temperament (TEM). We estimated SNP effects using a multi-SNP mixed-model. Further, SNP positions were mapped to genes, and GO terms/KEGG pathways of the corresponding genes were assigned. The estimation of GO term/KEGG pathway effects was based on a mixed-model using SNP effects as dependent variables; (3) Results: The number of significant SNPs comprised 59 for DCE, 25 for DSB and MSP, 17 for MCE and MSB, and 7 for TEM. Significant KEGG pathways were found for MSB (2), TEM (2), and MSP (1), while 11 GO terms were significant for MSP, 10 for DCE, 8 for DSB and TEM, 5 for MCE, and 3 for MSB.; (4) Conclusions: From the perspective of a better understanding of the genomic background of the phenotypes, traits with low heritabilities suggest that the focus should be moved from single genes to metabolic pathways or gene ontologies significant for the phenotype.

Recent climatic changes have resulted in an increased frequency and prolonged periods of drought and strained water resources affecting plant production. We explored the possibility of reducing irrigation in a container nursery and studied the growth response of seedlings of economically important forest trees: broadleaf deciduous angiosperms Fagus sylvatica, Quercus petraea and evergreen conifers Abies alba and Pinus sylvestris. We also studied markers of water stress including modifications of biomass allocation, leaf anatomy, proline accumulation and expression of selected genes. Growth of the broadleaved deciduous species was more sensitive to the reduced water supply than that of conifers. Remarkably, growth of the shade tolerant Abies was not affected. Adjustment of biomass allocations was strongest in P. sylvestris, with a remarkable increase in allocation to roots. In response to water deficit both deciduous species accumulated proline in leaves and produced leaves with shorter palisade cells, reduced vascular tissues and smaller conduit diameters, but not conifers. Relative transcript abundance of a gene encoding a Zn-finger protein in Q. petraea and a gene encoding a pore calcium channel protein 1 in A. alba increased as water deficit increased. These findings suggest that in container nursery, the genetic selection can be initiated by water deficit. Our study shows major differences between functional groups in response to irrigation, with seedlings of evergreen conifers having higher tolerance than the deciduous species. This suggests that major water savings could be achieved by adjusting irrigation regime to functional group or species requirements.

The paper presents data from a monthly campaign for the elemental composition of PM10 in a specific receptor Kotórz Mały (Opole Voivodeship) located in the vicinity of a moderately inhabited rural area, measured in one-hour samples with the use of the PX-375 analyzer by the Horiba company. The hourly variability of SO2, NO, NO2, CO, O3 concentrations as well as the variability of meteorological parameters were also determined. On average, during the entire measurement period, the elements related to PM10 can be arranged in the following order: As<V<Ni<Pb<Cr<Mn<Cu<Ti<Zn<K<Fe<Ca<Al<Si<S. Trace elements, including toxic elements, such as As, V, Ni, Pb, Cr, Mn, were present in low concentrations, not exceeding 10 ng/m3 (average daily value). These elements had fairly even concentrations, daily and hourly. The concentrations of the main elements in the PM10 in the receptor are subject to strong hourly changes related not only to changes in the structure of the sources identified in the statistical analysis but mainly to wind speed and direction changes (soil and sand particles pick-up and inflow of pollutants from coal combustion). It has been shown that the transport emission in the receptor can have an intense effect on PM10 in the afternoon.

The optical response of bulk germanium sulfide (GeS) is investigated systematically using different polarization-resolved experimental techniques, such as photoluminescence (PL), reflectance contrast (RC), and Raman scattering (RS). It is shown that while the low-temperature (T=5 K) optical band-gap absorption is governed by a single resonance related to the neutral exciton, the corresponding emission is dominated by the disorder/impurity- and/or phonon-assisted recombination processes. Both the RC and PL spectra are found to be linearly polarized along the armchair direction. The low and room (T=300 K) temperature RS spectra consist of six Raman peaks identified with the help of Density Fuctional Theory (DFT) calculations: Ag1, Ag2, Ag3, Ag4, B1g1, and B1g2, which polarization properties are studied under four different excitation energies. We found that the polarization orientations of the Ag2 and Ag4 modes under specific excitation energy can be useful tools to determine the GeS crystallographic directions: armchair and zigzag.

Cardiovascular diseases (CVDs) constitute the first cause of death among the population of developing and developed countries. Atherosclerosis, which is a disorder with multifactorial etiopathogenesis, underlies most CVDs. The available literature includes ample research studies on the influence of classic cardiovascular (CV) risk factors. However, environmental exposure to heavy metals, among other substances, is still an unappreciated risk factor of CVDs. This study aimed to assess the concentration of some heavy metals (copper (Cu), zinc (Zn), manganese (Mn), cobalt (Co), and iron (Fe)) in the blood serum of postmyocardial infarction (post-MI) patients and patients free from myocardial infarction (MI) as well as estimate the relationship between the occurrence of MI and increased concentration of heavy metals. The concentration of heavy metals (Cu, Zn, Mn, Co, and Fe) was assessed using the inductively coupled plasma mass spectrometry technique in a group of 146 respondents divided into two groups: post-MI group (study group (SG), n = 74) and group without cardiovascular event (CVE) having a low CV risk (control group (CG), n = 72). The concentration of the analyzed heavy metals was higher in SG. All the heavy metals showed a significant diagnostic value (p < 0.001). The highest value of area under the curve (AUC) was observed for manganese (Mn) (0.955; 95% confidence interval (CI) = 0.922–0.988), while the lowest value was found for zinc (Zn) (0.691; 95% CI = 0.599–0.782). In one-dimensional models, high concentrations of each of the analyzed heavy metals significantly increased the chances of having MI from 7-fold (Cu) to 128-fold (Mn). All the models containing a particular metal showed a significant and high discrimination value for MI occurrence (AUC 0.72–0.92). Higher concentrations of Cu, Zn, Mn, Co, and Fe were found to considerably increase the chances of having MI. Considering the increasingly higher environmental exposure to heavy metals in recent times, their concentrations can be distinguished as a potential risk factor of CVDs.