This study assesses the biomethane (CH4) generation and greenhouse gas (GHG) emissions resulting from municipal solid waste landfilling in Phnom Penh, Cambodia, with a focus on the impact of fugitive CH4 emissions and operation processes in four landfilling scenarios: simple dumping (S1), improved management with leachate treatment (S2), engineered landfill with flaring (S3), and engineered landfill with energy recovery (S4). The study also considered the environmental benefits of carbon sequestration and landfill gas utilization. The LandGEM and IPCC FOD models were used to calculate CH4 generation over the period of 2009-2022, and it was found that approximately 18 and 21 M kg/year of CH4 are released, respectively. The energy potential from CH4 recovery was 51–61 GWh/year. Overall GHG emissions in S2 were the highest, amounting to 409–509 M kg CO2-eq/year, while S1 had lower emissions at 397–496 M kg CO2-eq/year. Flaring captured CH4 in S3 could reduce GHG emissions by at least 55%, and using captured CH4 for electricity production in S4 could mitigate at least 83% of GHG emissions. Electricity recovery (S4) could avoid significant amounts of GHG emissions (˗104.5 kg CO2-eq/tMSW). The study suggests that landfill gas-to-energy could significantly reduce GHG emissions.

The COVID-19 pandemic has expanded globally and caused serious consequence in both health system and the economy. MPV is one of two oral antivirals for COVID-19 with mild-to-moderate symptoms that have received FDA approval so far. This study aims to evaluate the cost-utility of using MPV in COVID-19 treatment. To compare the utility costs of MPV and non-MPV treatments for COVID-19 patients, we used a decision tree model. Data on clinical efficacy, cost, and quality of life were gathered from previous studies. The incremental effective cost ratio (ICER) calculated based on costs incurred and quality-adjusted life years (QALY), was considered as primary out-come. The total cost of MPV treatment and not using MPV was 15,362,516 VND (618 USD) and 15,771,262 VND (634 USD), respectively. The estimated QALY with using-MPV was 28.33, while without MPV was 19.72. The ICER was dominant, resulting in savings of 47,453 VND/QALY (1.9 USD). MPV is a cost-effective medication used to treat COVID-19. In mild-to-moderate COVID-19 patients, MPV considerably lowers costs and improves quality of life. However, several clinical factors of the drug still need to be taken into account.

Alginate extraction is from seaweed, and lignin separation is from by-product corn (stalks and leaves). Alginate/lignin is a synthetic polymer rich in biological activity of great interest. Antioxidant activities of alginate/lignin were evaluated, such as total antioxidant activity, reducing power activity, DPPH free radical scavenging activity, and α – glucosidase inhibition activity. The test of anticancer activity was on four cell lines (Hep G2, fibroblast, MCF-7, and NCI H460). Determination of physical-chemistry characteristics of alginate/lignin was through FTIR, DSC, SEM_EDS, SEM_EDS mapping, XRD, XRF, and 1H-NMR. A study of acute toxicity of alginate/lignin was on Swiss albino mice. The results showed alginate/lignin possessed antioxidant activity such as total antioxidant activity, reducing power activity, especially, α – glucosidase inhibition activity, and no free radical scavenging activity. Alginate/lignin did not be typical in cancer cell lines. Alginate/lignin existed in a thermally stable regular spherical shape in the investigated thermal region. Some specific functional groups of alginate and lignin did not exist in alginate/lignin crystal. Elements such as C, O, Na, and S were popular in the alginate/lignin structure. LD0 and LD100 of alginate/lignin in mice were 3.91 g/kg and 9.77 g/kg, respectively. Alginate/lignin is the potential for application as pharmaceutical materials, functional foods, and supporting diabetes treatment.

In this paper, the classical least square (CLS) method with molecular absorption spectrophotometric measurement was used to determine simultaneously of paracetamol (PAR), ibuprofen (IBU), and caffeine (CAF) in tablets. The absorbance spectra of the standard solutions and samples were measured over a wavelength from 220 to 300 nm with a 0.5 nm step. The concentration of PAR, IBU and CAF in the sample solutions were calculated by using a program called CLS-Excel written in Microsoft Excel 2016 and Visual Basic for Applications (VBA). The method and CLS-Excel program were tested on mixed standard laboratory samples with different PAR, IBU, and CAF concentration ratios, and they showed small errors and satisfying repeatability. An analytical procedure for tablets containing PAR, IBU, and CAF was developed. The reliability of the procedure was proved via the recovery and repeatability of the analysis results with an actual tablet sample and comparing the mean contents of active substances in the tablets obtained from the analytical procedure with the from the HPLC method. The procedure is simple with a reduced cost compared with the HPLC standard method.

The Soil and Water Assessment Tool (SWAT) is one of the most widely used hydrologic models. SWAT has been undergoing constant changes since its development. However, compartment review and testing of SWAT are comparably limited, especially the flood routing functions. In this study, the daily flood routing subroutines of different SWAT versions were reviewed and tested using a well observed segment of the Weser river located in Germany. Results show several problems with the flood routing subroutines of SWAT. The variable storage subroutine of SWAT (revision 664) does not transform the flood wave. Unphysical results could be obtained with the variable storage routing of SWAT (revision 528). The Muskingum subroutine of SWAT (revisions 664 and 528) overestimates channel evaporation (resulting in a bias of 14\% to 19% in streamflow) and underestimates transmission losses. Simulated results show that the timing and shape of the flood wave could be improved with a corrected Muskingum subroutine. Based on the results of this study, we suggest the SWAT user community to review their existing SWAT models to see how the aforementioned issues will affect their methods, findings and conclusions.

Agricultural land fires have been linked to various and adverse impacts on ecosystems, food security and the agriculture sector. Understanding the patterns and drivers of agricultural land fires is essential for effective agricultural land fire management. The key objectives of this study were to (1) analyze the temporal and spatial patterns of agricultural land fires using satellite remote sensed data, (2) assess a range of environmental conditions that could drive the occurrence of agricultural land fires, (3) determine the best model for predicting agricultural land fires and (4) determine the relative contribution of each environmental condition variable on the best predictive model. We used both univariate and multivariate regressions for the fire prediction capability of four independent environmental conditions (fuel, weather, topographic and anthropogenic). Analysis of historical satellite data revealed that agricultural land fires were more frequent than forested land fires. Our analyses also revealed that fuel condition was the most important variable for predicting agricultural land fires followed by weather, topographic and anthropogenic conditions. This study provides a novel multivariate model for predicting agricultural land fires that harbors the potential to improve agricultural land fire management and reduce fire risk within the agricultural sector.

This investigation aims to discuss the formation process of eddies and the heat transportation in plasma keyhole arc welding. In order to clarify this issue, the measurement of the convection inside the weld pool, the convection on the weld pool surface, also the temperature distribution on the weld pool surface were carried out. The results showed that two eddies were found in the weld pool, which is controlled mainly through the shear force by the plasma flow acting on the weld pool surface. The magnitude, extent and direction of the shear force are thought to be determined primarily by the variation of keyhole profile. The relative shape and strength of each eddy is largely changed depending on the change of the keyhole profile when nozzle diameter changed. These relative strengths of each eddy are considered to decisively govern the heat transport in the weld pool coinciding with the direction of eddies. A larger eddy near the lower part of the keyhole inside the weld pool was found out in the case of 1.6 mm, meanwhile a upward larger eddy was found out near the upper part of the keyhole inside the weld pool in the case of 2.4 mm.

With the introduction of HTTP/3, whose transport is no longer the traditional TCP protocol but the novel QUIC protocol, research for solutions to the unfairness of Adaptive Streaming over HTTP (HAS) has become more challenging. That is, because of different transport layers, the HTTP/3 may not be available for some networks and the clients have to use HTTP/2 for their HAS applications instead. Therefore, the scenario that HAS over HTTP/3 (HAS/3) compete against HTTP/2 (HAS/2) must be considered seriously. However, there have been a shortage of investigations on the performance and the origin of the unfairness in such a cross-protocol scenario in order to produce proper solutions. Therefore, this paper provides a performance evaluation and root-cause analysis of the cross-protocol unfairness between HAS/3 and HAS/2. It is concluded that, due to differences in the congestion control mechanisms of QUIC and TCP, HAS/3 clients obtain larger congestion windows, thus requesting higher video bitrates than HAS/2. As the problem lies in the transport layer, existing client-side ABR-based solutions for the unfairness from the application layer may perform suboptimally for the cross-protocol case.

Knee osteoarthritis is the most popular type of osteoarthritis that causes extreme pain in elderly. Currently there is no cure for osteoarthritis. To lessen clinical symptoms, glucosamine was suggested. The primary goal of our study is to evaluate the efficacy and safety of glucosamine from recent studies. Electronic databases such as PubMed, Scopus, Cochrane were used to assess RCT. From the beginning through March 2023, the papers were checked, and if they fulfilled the inclusion criteria, they were then examined. WOMAC and VAS scales were considered as main outcome measure. A total of 15 studies were selected. Global pain was significantly decreased in comparison to placebo, as measured by the VAS index, with an overall effect size SMD of -7.41 ([95% CI] 14.31, 0.51). The WOMAC scale confirmed that pain, stiffness, and physical function had improved, however the effects were insufficient. A statistical update also revealed that there were no reports of serious medication interactions or significant adverse events. To summarize, glucosamine is more effective than a placebo at reducing pain in knee osteoarthritis patients. In long-term treatment, oral glucosamine sulfate 1500 mg/day is believed to be well tolerated.

HTTP/2 video streaming has caught a lot of attentions in the development of multimedia technologies over the last few years. In HTTP/2, the server push mechanism allows the server to deliver more video segments to the client within a single request in order to deal with the requests explosion problem. As a result, recent research efforts have been focusing on utilizing such a feature to enhance the streaming experience while reducing the request-related overhead. However, current works only optimize the performance of a single client, without necessary concerns of possible influences on other clients in the same network. When multiple streaming clients compete for a shared bandwidth in HTTP/1.1, they are likely to suffer from unfairness, which is defined as the inequality in their bitrate selections. For HTTP/1.1, existing works have proven that the network-assisted solutions are effective in solving the unfairness problem. However, the feasibility of utilizing such an approach for the HTTP/2 server push has not been investigated. Therefore, in this paper, a novel proxy-based framework is proposed to overcome the unfairness problem in adaptive streaming over HTTP/2 with the server push. Experimental results confirm the outperformance of the proposed framework in ensuring the fairness, assisting the clients to avoid rebuffering events and lower bitrate degradation amplitude, while maintaining the mechanism of the server push feature.

Edge computing has emerged as a significant computing trend alongside the rapid expansion of the Internet of Things (IoT). Computing operations at the network’s edge offer a solution to the high latency and service overload challenges often associated with cloud computing. Additionally, the Secure Hash Algorithm-3 (SHA-3) plays a crucial role in ensuring data integrity and is implemented for numerous applications in the IoT field. Therefore, integrating the SHA-3 accelerator into edge computing is essential. Moreover, recent studies about SHA-3 have primarily focused on achieving high performance and optimizing resource utilization for SHA-3. However, these studies have overlooked the crucial aspect of data transfer between the external memory and the hash function block, as transfer time plays a significant role. This paper proposes an efficient SHA-3 architecture designed for System-on-Chip (SoC) Field Programmable Gate Array (FPGA) to address the aforementioned challenges and be suitable for real edge computing. The architecture contains three key techniques. First, the harmony of padding and Direct Memory Access (DMA) for managing the data transfer process and enhancing performance efficiency based on Serial Input to Parallel Output (SIPO) and a barrel shifter. Secondly, implementing internal pipelining within the Round Function (RF) to reduce critical path delays and optimize resource utilization. Finally, designing four modes (SHA3-224, SHA3-256, SHA3-384, and SHA3-512) to cater to various applications. Our architecture is implemented and tested on the DE10-Standard Development Kit (Cyclone V SX SoC-5CSXFC6D6F31C6N), which is integrated into the FPGA and is controlled by a Dual-Core ARM Cortex-A9 processor. The result is up to 38.34 Gbps in throughput and 5.61 Mbps/ALM in efficiency for the RF computation, 28.02 Gbps in throughput, and 3.63 Mbps/ALM for the full proposed architecture.

The objective of this study was to describe the overall pattern of morbidity and mortality of children seen at the Thai Binh Pediatric Hospital in Vietnam, with a focus on infectious diseases. A retrospective review of hospitalisation records was conducted from 1 January 2015 to 31 December 2019. Data were obtained from a total of 113,999 records. The median age of patients was 18 months, with 83.98% of patients aged <5 years. Infectious diseases accounted for 61.0% of all cases. The most prevalent diseases were lower respiratory tract infections (32.8%), followed by gastrointestinal infections (13.3%) and confirmed influenza (5.4%). Most infections were not microbiologically documented. A total of 81.4% patients received at least one antibiotic. Most patients (97.0%) were hospitalised for less than 15 days. Regarding outcomes, 87.8% patients were discharged home with a favourable outcome. 12.0% were transferred to the Vietnam National Children’s Hospital because their condition had worsened and 0.1% died. In total, infectious diseases accounted for 40.4% of deaths, followed by neonatal disorders (34.6%). Our data serves a basis for the identification of needs for diagnostic tools and for future evaluation of the effect of the targeted implementation of such facilities. Point-of-care tests, including real-time PCR assays to identify common pathogens should be implemented for more accurate diagnosis and more appropriate antibiotic use.

The electrokinetics methods have a great potential to characterize hydrogeological processes in geological media, especially in complex hydrosystems such as fractured formations. In this work, we conceptualize fractured media as a bunch of parallel capillary fractures following the fractal size distribution. This conceptualization permits to obtain analytical models for both the electrical conductivity and the electrokinetic coupling in water saturated fractured media. We explore two different approaches to express the electrokinetic coupling. First, we express the streaming potential coupling coefficient as a function of the zeta potential and then we obtain the effective charge density in terms of macroscopic hydraulic and electrokinetic parameters of porous media. We show that when the surface electrical conductivity is negligible, the proposed models reduces to the previously proposed one based on a bundle of cylindrical capillaries. This model opens up a wide range of applications to monitor the water flow in fractured media.

This article explored how some state policies on rehabilitation, protection and utilization of mangroves are implemented at two locals; namely, Ca Mau provice and its sub-unit Ngoc Hien District as well as Ho Chi Minh City and its sub-unit Can Gio District and what are considered as emgerging issues in the implementation process. The study employed mixed research methods including document and thematic analysis, in-depth interviews, and group discussion. The findings showed that state policies would be adapted through the ways in which these two locals manage to silmultaneously orient their work toward accommodating the madates placed upon them and cope with the reality of socio-economic difficulties at their levels. The findings also showed some issues that need to consider addressing; namely, locals’ struggles to fill the gaps between written and implemented policies in mangrove rehabilitation, conflict among sectors and stakeholders in mangrove utilization and protection, problems in guaranteeing adequate budget for in-need-locals, inconsistence in policies on "forest: water surface” ratio in mangrove-shrimp farm, and unintended consequences in forest thinning and exploitation regimes. Based on the finding analysis, the articles discussed lessons learned from the policy implementation process on mangrove rehabilitation, management and forest allocation to household in the south of Vietnam.

The osteoarthritis (OA), the main cause of disability, is a chronic condition that most frequently affects older adults. As the population ages, the cost of treatment is placing pressure on the healthcare budget. As a result, it is imperative to evaluate the medicines' cost-effectiveness and the influence they have on health resource allocation. Hence, our study aims to summarize the cost and outcome of utilizing glucosamine in OA treatment. Authentic databases like Medline, Cochrane, and Scopus were adopted for the identification process up until July 2023. Our primary inclusion criteria centered on the economic evaluation of Glucosamine in OA treatments with provided the incremental cost-effectiveness ratio (ICER) at least. The Quality of Health Economic Studies (QHES) instrument was applied to grade the quality of the studies. A total of 7 qualified studies were selected and discussed the cost-effectiveness of glucosamine with or without other formulations. All of them demonstrated that glucosamine was cost-effective. There was an in-creasement of QALY when incorporating Glucosamine into conventional care. Moreover, Crystalline Glucosamine Sulfate (pCGS) was more cost-effective than the Other Formulations of Glucosamine (OFG). In overall, utilizing pCGS was more beneficial than OFG in terms both of cost and quality of life.

The regenerated magnesia-calcium brick samples that had added 0, 1.5, 3.0 wt.% aluminium oxide (Al2O3) were prepared by using spent magnesia-calcium bricks, fused magnesia and Al2O3 powder additive as the main raw materials. The phases, microstructures, room temperature and hot flexural strength, resistance to cement clinker corrosion and strength of coating adherence were investigated respectively. It indicated that the addition of Al2O3 increased mainly resulting in the content of tetracalcium aluminoferrite (C4AF) and tricalcium aluminate (C3A) increased in the regenerate samples. The bulk density, the room temperature flexural strength and the strength of coating adherence all increased, while the hot flexural strength and corrosion resistance both deteriorated along with the increase of Al2O3 addition. It was because that on the one hand the low melting point phases of C4AF and C3A improved the sinterability of the regenerated samples during the burning stage, on the other hand they melted or existed in liquid phase during the experimental temperature (1573 K and 1823 K) which degraded hot flexural strength and corrosion resistance, and enhanced the strength of coating adherence as the wettability of the liquid phase. The content of Al2O3 in the regenerated magnesia-calcium brick should not be higher than 1.1 wt.%, considering its room and high-temperature performances for cement rotary kiln.

The Vu Gia - Thu Bon River Basin (VG-TB) is confronting numerous challenges related to water security (WS), particularly in the face of the impacts of climate change. These challenges manifest in salinity intrusion, altered rainfall patterns, and reduced water supply in downstream areas. To assess the current state of water security in the basin, the study employed statistical analysis methods, Process Analysis Method (PAM), SMART, and Analytic Hierarchy Process (AHP) to develop a comprehensive Assessment Framework for Water Security (AFWS) in the VG-TB. The AFWS encompasses five key dimensions, 17 indicators, and 28 variables, aligning with the UN-Water definition of water security and addressing the Sustainable Development Goal 6 (SDG6) criteria for global water sustainability. It also adheres to the Asian Development Bank's (ADB) approach to water security assessment as outlined in the Asian Water Development Outlook (AWDO) reports. This allows for the computation of a comprehensive Water Security Index (WSI) for specific regions, serving as a foundation for decision-making and policy formulation aimed at enhancing water security in the context of climate change and facilitating sustainable basin development in the future.

Introduction: Hemostatic dysfunction during extracorporeal membrane oxygenation (ECMO) due to blood-circuit interaction and the consequences of shear stress by flow rates lead to rapid activation of the coagulation cascade and thrombus formation in the ECMO system and blood vessels. In this study, we aimed to identify the incidence and risk factors for cannula-associated arterial thrombosis (CaAT) post-decannulation. Methods: A retrospective study of patients undergoing arterial cannula removal following ECMO. We evaluated the incidence of CaAT and compared clinical characteristics, pre-ECMO severity, and daily hemostasis parameters in patients with and without CaAT. Multivariate analysis revealed the risk factors for CaAT. Results: Forty-seven patients requiring venoarterial ECMO or hybrid methods were recruited to be screened for thrombosis. The median SOFA score was 11 (8-13). CaAT occurred in 29 patients (61.7%), with thrombosis in the superficial femoral artery accounting for 51.7%. Limb ischemia complications in the group with CaAT was 17.2%. In multivariate analysis, an ECMO flow rate of 100 mL/min was determined to be the independent factor for CaAT with an OR of 0.84 (95% CI, 0.73–0.95, p=0.008). Conclusion: In patients successfully weaned from ECMO, the incidence of CaAT was 61.7%. Our study found that a low-flow rate of ECMO was an independent risk factor for CaAT.

The coastline in the Ca Mau and the Kien Giang provinces of the Vietnamese Mekong Delta has been severely eroded in recent decades. Pile-Rock Breakwaters (PRBW) are one of the most widely adopted structures for controlling shoreline erosion in this region. These structures are effective for wave energy dissipation, stimulating sediment accumulation, and facilitating the restoration of mangrove forests. These breakwaters are generally considered to be best-engineering practice however there is currently insufficient scientific evidence with regard to specific structural design aspects. This can lead to PRBW structures being compromised when deployed in the field. This study uses a physical model of a PRBW in a laboratory to investigate several design parameters, including crest width and working states (i.e. submerged, transition, and emerged), and investigates their relationship with the wave transmission coefficient, wave reflection coefficient, and wave energy dissipation. To investigate these relationships further, empirical formulas were derived for PRBWs under different sea states and crest widths to aid the design process. The results showed that PRBW width had a significant influence on the wave energy coefficients. The findings revealed that the crest width of the breakwater is inversely proportional to the wave transmission coefficient (K_t) under the emerged state. The crest width is also proportional to the wave reduction efficiency and wave energy dissipation in both working states (i.e., submerged and emerged states). The front wave disturbance coefficient (K_f) was found to be proportional to the wave reflection coefficient, and the wave height in front of the structure was found to increase by up to 1.4 times in the emerged state. The wave reflection coefficient requires special consideration to reduce the toe erosion in the structure. Lastly, empirical equations including linear and non-linear formulas were compared with previous studies for different classes of breakwaters. These empirical equations will be useful for understanding the wave transmission efficiency of PRBWs. The findings of this study provide important guidance for PRBW design in the coastal area of the Mekong Delta.

IntroductionThe aim of this study is to describe the epidemiology of all COVID-19 patients in Vietnam and to describe the measures of disease control and prevention implemented. MethodsData were recovered from Wikipedia regarding the 2020 coronavirus pandemic in Vietnam. The period covered was from 23 January to 20 April 2020. Descriptive analysis was stratified by gender, age, country of origin, travel history, clinical symptoms and outcome. A survey of disease control and prevention measures was conducted at the Centre for Disease Control in the Thai Binh province, which is responsible for screening and isolating individuals at high risk of COVID-19. ResultsAs of 20 April 2020, Vietnam had recorded 268 confirmed COVID-19 patients. 55.2% were female. 67.9% were aged 20-49 years and 82.5% were Vietnamese. 60.4% of cases were imported from outside Vietnam. Other cases were acquired in Vietnam by individuals in close contact with imported cases. Only one patient who had not travelled had had no known contact with a confirmed case. 63.1% of patients were asymptomatic. 75.7% of patients were discharged. No deaths were recorded. The Thai Binh CDC surveyed a total of 2,203 persons at risk of COVID-19. 336 persons (15.2%) were isolated at hospitals and 1,411 (64.0%) in dedicated isolation facilities. 16.4% reported at least one respiratory symptom. No positive cases confirmed by RT-PCR have been reported in the Thai Binh province to date. ConclusionThe effect of the systematic screening and isolation strategy made it possible to limit local transmission in Vietnam. Vietnam needs to reinforce diagnostic capacities, prevention measures and provide the necessary epidemiological data on which to base interventions. The wider use of rapid serological tests is also advisable in order to be able to conduct extensive screening in the community.

Skin image analysis using artificial intelligence (AI) has recently attracted significant research interest, particularly for analyzing skin images captured by mobile devices. Acne is one of the most common skin conditions with profound effects in severe cases. In this study, we developed an AI system called AcneDet for automatic acne object detection and acne severity grading using facial images captured by smartphones. AcneDet includes two models for conducting two tasks: (1) a Faster R-CNN-based deep learning model for the detection of acne lesion objects of four types including blackheads/whiteheads, papules/pustules, nodules/cysts, and acne scars; and (2) a LightGBM machine learning model for grading acne severity using the Investigator’s Global Assessment (IGA) scale. The output of the Faster R-CNN model, i.e., the counts of each acne type, were used as input for the LightGBM model for acne severity grading. A dataset consisting of 1,572 labeled facial images captured by both iOS and Android smartphones was used for training. The results show that the Faster R-CNN model achieves a mAP of 0.54 for acne object detection. The mean accuracy of acne severity grading by the LightGBM model is 0.85. With this study, we hope to contribute to the development of artificial intelligent systems that are able to help acne patients understand more about their conditions and support doctors in acne diagnosis.

Nowadays, the uses of laser and optics in the medical areas are extremely vivid, especially low-level laser therapy. The light with the wavelength of 633 nm to 1200 nm could penetrate and propagate deep in biological tissue. To develop the low-level laser therapy device, optimizing light delivery is critical to accurately stimulate the biological effects inside the biological tissue. Nevertheless, each form of the tissues at each zone on the body had various refractive optic, absorption, scattering, and anisotropy coefficients. This paper describes the simulation results of low-level laser propagation from skin surface at the lower spine, the knee, the femur and the prostate gland with four wavelengths (633 nm, 780 nm, 850 nm, and 940 nm) by the Monte Carlo method. These simulation results are the base for developing the low-level laser therapy device, that could be used in clinical for treating the fracture, knee osteoarthritis, spinal degeneration, and benign prostatic hypertrophy.

Curcuma longa is only a rich source of curcumin (1) and its major analogues demethoxycurcumin (2) and bisdemethoxycurcumin (3) among the Curcuma species. The content ratio of these three curcumins in turmeric is depended on the varieties and growing environment. Recently, curcumin (1) has been reported as potential inhibitor of hepatic and enzymatic protein tyrosine phosphatase 1B (PTP1B) and its related disorders such as hypertriglyceridemia, hyperlipidemia and liver steatosis. Thus, we further purified curcumins (1–3) from C. longa and investigated their inhibitory effects against PTP1B and α-glucosidase enzymes. As the result, curcumins (1–3) exhibited potential PTP1B inhibition with IC50 values of 37.8 ± 1.4, 45.3 ± 0.7, and 72.6 ± 1.1 μM, respectively, and α-glucosidase inhibition with similar manner (IC50 values of 78.2 ± 0.2, 82.4 ± 0.6, and 90.6 ± 1.0 μM, respectively). These results reveal a key role of methoxylation in the variation of PTP1B and α-glucosidase inhibitory activity for these curcumins. In addition, density functional theory (DFT) was used accompanying with molecular docking (MD) to analyze the ligand stability and the interaction of curcumins (1–3) with PTP1B and glucoside hydrolase proteins. Assay-based results and the MD data obtained are highly correlation suggesting that the deterioration of the enzyme activity caused by the distortion of structural conformation of PTP1B and glucoside hydrolase may be related to the arrangement of amino acids in protein structure. This reported for the first time that inhibitory effects of curcumins (1–3) against PTP1B and glucoside hydrolase have been examined in vitro and in silico as well.

Damage assessment is one of the most crucial issues for bridge engineers, especially for existing steel bridges. Among several methodologies, the vibration measurement test is a typical approach in which the natural frequency variation of the structure is monitored to detect the existence of damage. However, locating and quantifying the damage is still a big challenge. In this regard, the artificial intelligence (AI)-based approach seems a potential way to accomplish those obstacles. This study deploys a comprehensive campaign to determine all dynamic parameters of a pre-damage steel truss bridge structure. Based on the results of mode shape, natural frequency, and damping ratio, a finite element model (FEM) is created and keeps updating. The artificial intelligence network's input data will be analyzed and evaluation from damage cases. The trained artificial neural network model will be curated and evaluated to confirm the approach's feasibility. During the actual operational stage of the steel truss bridge, this damage assessment system is showing good performance in terms of monitoring the structural behavior of the bridge under some unexpected accidents.

At the end of the dry season in early March to early April each year, extensive agricultural biomass waste burnings occur throughout insular mainland Southeast Asia. During this biomass burnings period, smoke aerosols blanket the whole regions and were transported and dispersed by predominant westerly and south westerly winds to southern China, Taiwan and as far southern Japan and the Philippines. The extensive and intense burnings coincided with some wildfires in the forests due to high temperature making the region one of the global hot spots of biomass fires. In this study, we focus on the effect of pollutants emitted from biomass burnings in March 2019 at the height of the burnings period to the exposed population and their health impact. The Weather Research Forecast- Chemistry (WRF-Chem) model was used to predict the PM2.5 concentration over the simulating domain and health impacts are then assessed on the exposed population in the four countries of Southeast Asia, namely Thailand, Laos, Cambodia and Vietnam. Using the health impact based on log-linear concentration response function and Integrated Exposure Response (IER), the results show that at the peak period of the burnings from 13 to 20 March 2019, Thailand experienced the highest impact, with an estimated 2170 premature deaths. Laos, Vietnam, and Cambodia followed, with estimated mortalities of 277, 565, and 314 deaths respectively. However, when considering the impact per head of population, Laos exhibited the highest impact, followed by Thailand, Cambodia, and Vietnam. The results highlight the significant health impact and associated economic cost of agricultural waste burnings in Southeast Asia at the end of the dry season. And hence policy makers should take these into account to design measures to reduce the negative impact of widespread burnings on exposed population in the region.

Catalase, an antioxidant enzyme widely produced in mammalian cells and bacteria, is crucial in mitigating oxidative stress in a hostile environment. This function enhances the intracellular survivability of various intracellular growth pathogens, including Brucella abortus. In this study, to determine whether the inhibition of catalase can inhibit the intracellular growth of Brucella (B.) abortus, we employed 3-amino-1,2,4-triazole (3-AT), a catalase inhibitor, in both RAW 264.7 macrophage cells and an ICR mouse model during Brucella infection. The intracellular growth assay indicated that 3-AT exerts growth-inhibitory effects on B. abortus within macrophages. Aside from that, it contributes to the accumulation of reactive oxygen species and the formation of nitric oxide. Notably, 3-AT diminishes the activation of the nucleus transcription factor (NF-κB) and modulates cytokine secretion within infected cells. In our mouse model, the administration of 3-AT reduced B. abortus proliferation within the spleen and liver of infected mice. This reduction was accompanied by a diminished immune response to infection, as indicated by lowered levels of TNF-α, IL-6, IL-10, and altered CD4+/CD8+ T-cell ratio. These results suggest the protective and immunomodulatory effects of 3-AT treatment against Brucella infection.

Modern agriculture demands for comprehensive information about the plant itself. Conventional chemistry-based analytical methods - due to their low throughput and high associated cost - are no longer capable of providing these data. In recent years, remote reflectance-based characterization has developed as one of the most promising solutions for rapid assessments for plant attributes. However, in many cases, expensive equipment is required because accurate quantifications need assessment of the full reflectance spectrum. We examined the versatility of visible colour sensors as reflectance measuring devices for biological / biochemical quantifications on sweet basil (Ocimum basilicum). Our results indicate for the wide potential of spectral colour sensors for quantitative determination of leaf phenolic compounds, flavonoids in particular, and non-invasive plant phenotyping in agricultural applications by low-cost sensors.

In urban area, one of the great problem is the rise of temperature, which leads to form the urban heat island effect. This paper refers to the trend of the urban surface temperature extracted from the Landsat images from which to consider changes in the formation of surface urban heat island for the north of Ho Chi Minh city in period 1995-2015. Research has identified land surface temperature from thermal infrared band, according to the ability of the surface emission based on characteristics of normalized difference vegetation index NDVI. The results showed that temperature fluctuated over the city with a growing trend and the gradual expansion of the area of the high-temperature zone towards the suburbs. Within 20 years, the trend of the formation of surface urban heat island with two typical locations showed a clear difference between the surface temperature of urban areas and rural areas with space expansion of heat island in 4 times in 2015 compared to 1995. An extreme heat island located in the inner city has an area of approximately 18% compared to the total area of the region. Since then, the solution to reduce the impact of urban heat island has been proposed, in order to protect the urban environment and the lives of residents in Ho Chi Minh City becoming better

Numerical simulations and experiments on evaporative condensers in air conditioning systems using R744 were performed. Two configurations were given to study the feasibility of operating the subcritical R744 cycle. It indicated the capable of evaporative cooling condensing R744 to liquify by analyzing the outlet temperature at the end of the condenser reached from 28.7oC to 30.3oC with the operating pressure from 72.6 bar to 68.5 bar. The mass flow rate in the study increases from 14.34 kg/h to 46.08 kg/h, the pressure drop also increases from 0.23 bar to 0.47 bar for the simulation and 0.4 bar to 0.5 bar for the experiment, respectively. This study indicates that a 5-layers of copper tubes configuration causes a higher pressure drop and lower COP when compared to an 8-layers of copper tubes that split into 2 sets for smaller pressure drop. In this study, the evaporative condensers using mini tubes that are flooded in the cooling water tank are suitable for the subcritical R744 air conditioning system. The results obtained from the experimental data are in good agreement with those obtained from the numerical results, with the deviation less than 5%.

Urbanization-induced land use transition results in a decline in ecosystem services, which has implications for regional ecological security. In order to explore the relationship between ecosystem services and land use transition, this paper utilizes the InVEST model, geographically weighted regression model to examine the impact of land use transition on ecosystem services in the Dongting Lake area (DLA). The results showed that (1) During the period 2000-2020, the intensity and motivation of land-use transition showed obvious spatial and temporal heterogeneity with the variation of urbanization development. (2) Habitat quality and Carbon sequestrations showed a downward trend. In contrast, food supply followed an upward trend; soil conservation and water yield services initially increased and dropped later. The overall spatial changes in habitat quality and Carbon sequestration appear to be insignificant. Food supply shows significant differences in the plains compared to other areas; while soil conservation and water yield service shows significant changes in places other than the DLA. (3) From 2000 to 2020, land use transition dynamics, population density, GDP density, night lighting and transition intensity had mainly negative effects on ecosystem services. Only the Normalized Vegetation Index (NDVI) showed a positive effect on ecosystem services. The results of the research will provide valuable references for the development and implementation of spatial ecological restoration planning and land use policies in the national territory.

This paper investigates experiences of how local cultural norms and social capital influenced the disaster relief process following the 2011 GEJET disaster. To underline social capital’s multiple‐influence aspects, this paper draws from field research that focuses on collective and individual social capital in disaster relief to systematise the findings according to the social capital framework. The paper uncovers new effects of individual social capital and collective capital in a mega-disaster context, thus contributing to pushing the research agenda toward a more critical appraisal of individual social capital and collective capital. We contribute to the nascent but growing literature that clarifies the relationship between social capital and disaster resilience. A qualitative study was conducted to capture the essence of their shared experiences. Findings revealed three main themes capturing the essence of the research participants’ disaster experiences. First, disaster response relied mostly on locally driven relief due to a clear understanding of the local culture. Second, there was an urgency to establish a sense of normalcy by providing quality supplies that would help survivors. Third, Japanese gender roles and expectations were reflected in the disaster relief process. The themes establish a wide array of lived experiences that are important to reflect on the role social capital plays in the policy-making and needs assessment processes in post-disaster relief and response efforts. The findings provide insights for integrating social dimensions into a humanitarian aid culture as citizens work towards a sense of normalcy.

Triple-negative breast cancer (TNBC) is a subtype of breast cancer characterized by the lack of estrogen receptors (ER), progesterone receptors, and HER-2 receptors. Thus, TNBC tumours do not benefit from the current therapies targeting ER or HER-2. Therefore, there is an urgent need to develop novel treatment for this subtype of breast cancer. Marijuana is a common name given to Cannabis plants, a group of plants in the Cannabis genus of the Cannabaceae family. Cannabis plants are among the oldest cultivated crops, traced back at least 12,000 years and are well known for their multi-purpose usage, including medicinal purposes. The main active compounds extracted from Cannabis plants are 21-carbon-containing terpenophenolics, which are referred to as phytocannabinoids. Of these, the tetrahydrocannabinol (THC) group contains highly potent cannabinoids, including delta-9-tetrahydrocannabinol (∆9-THC) and delta-8-tetrahydrocannabinol (∆8-THC), which are the most abundant THCs and are largely responsible for psychological and physiological effects of marijuana. The use of Cannabis plants for medicinal purposes was first recorded in 2337 BC in China, where Cannabis plants were used to treat pains, rheumatism, and gout. Recently, several cannabinoids have been approved for a number of treatments, one of which is the treatment of nausea and vomiting caused by chemotherapy in cancer patients. Furthermore, increasing evidence shows that cannabinoids not only attenuate side effects due to cancer treatment, but might also potentially possess direct antitumor effects in several cancer types, including breast cancer. However, anti-tumour activity of marijuana has been variable in different studies and even promoted tumour growth in some cases. In addition, the mechanisms of cannabinoid action in cancer remain unclear. This review summarizes evidence about the mixed actions of cannabinoids in cancer in general and triple-negative breast cancer in particular.

Domain generalization has led to remarkable achievements in Hyperspectral Image (HSI) classification. Inspired by contrastive language-image pre-training (CLIP), the language-aware domain generalization method has been explored to learn cross-domain-invariant representation. However, existing methods face some challenges: 1) The weak capacity to extract long-range contextual information and inter-class correlation. 2) Due to the inadequacies of the large-scale pre-training for HSI data, the spatial-spectral features of HSI and linguistic features can not be straightforwardly alignment. To address the above problems, a novel network has been proposed with a CLIP framework, which consists of an image encoder, based on an encoder-only transformer to obtain the global contextual information and inter-class correlation, a frozen text encoder, and a cross-attention mechanism, named Linguistic-Interact-with-Visual Engager (LIVE), enhances the interaction between two modalities. Extensive experiments demonstrating superior performance over state-of-the-art methods in HSI Domain Generalization with a CLIP framework.

This study aimed to evaluate the effect of incorporating linseed oil and fish oil in the diet on intake, ruminal fermentation milk yield and milk fatty acid profile in dairy goats. Four crossbred Saanen lactating goats in mid-lactation and milking 1.30±0.28 g/day were used in a 4 × 4 Latin square design. The basal diet consisted of concentrate and Para grass (C:F 40:60). Treatments included the basal diet without oil supplement (Ctrl) or with 2.5% linseed oil (LO2.5), 2.5% linseed oil and fish oil (3:2, w/w, LFO2.5), and 4.16% linseed oil and fish oil (3:2, w/w, LFO4.16). Diets had no effect on intake, milk yield, milk composition and ruminal fermentation patterns (P > 0.05). The lower (P < 0.05) proportions of C10:0-C14:0 in milk fat were observed with LFO4.16 compared with Ctrl. Compared with the Ctrl and linseed oil added alone, feeding LFO4.16 resulted in a 589% and 303% increase in C18:1 t11, respectively. Milk c9,t11 CLA was markedly increased with the LFO4.16 diet, accounting for 4.53 and 2.94 times greater concentrations than those in Ctrl and LO2.5 diets, respectively (P < 0.01). Goats fed LFO2.5 and LFO4.16 had greater levels of C22:6n-3 (0.63% and 0.87%; P < 0.001) compared with those fed Ctrl and LO2.5 diets (0.06% and 0.08%). Overall, the combined data suggested that including 4.16% linseed oil and fish oil in the diet of dairy goats is effective for improving the concentrations of healthy fatty acids in milk, without affecting milk production.

Changing climate conditions and rapidly increasing carbon dioxide emissions have severely affected the global ecosystem and world economy. Governments around the world have paid attention to these resulting challenges and enacted many policies to reduce environmental pollution and carbon dioxide (CO2) emissions. This study aimed to determine and understand the relationship between innovation, foreign direct investment, economic growth, renewable consumption and CO2 emission in Vietnam. Information was collected annually based on the annual data of the General Statistics Office of Vietnam and World Bank from 2000 to 2022. Data processing was conducted using the STATA 17.0 software. The innovation affects Vietnam’s environmental pollution. Innovation positively affect environmental pollution in Vietnam; if Vietnam’s innovation were to increase by 1%, CO2 emissions would increase by 0.68%. The empirical research results of this study also show that renewable energy consumption has a negative effect on environmental pollution in Vietnam; if renewable energy were consumed at a 1% increase, CO2 emission would decrease by 0.51%. In addition, FDI inflows and economic growth have strongly positive affecting to environmental pollution; if Vietnam’s FDI inflows were to increase 1%, CO2 emissions would increase 1.39%; if Vietnam’s GDP increase 1% then CO2 emission would increase 1.26%. This paper also provides some recommendations that can assist Vietnam in developing a green and sustainable economy in the technology revolution 4.0 to achieve the United Nations Sustainable Development Goals (SDGs) over a long-term period.

Background: Acute hepatopancreatic necrosis disease (AHPND), is a bacterial disease of whiteleg shrimp, which has a high mortality rate (100%) and incurs economic losses. Our objective was to identify the genes which lead to cell and organ damage and investigate bioproducts to prevent and treat. Methods: Litopenaeus vannamei shrimp in Thua Thien Hue province, Vietnam were collected from an infected pond and analysed at the Institute of Biotechnology, Hue University. The PirA gene of Vibrio parahaemolyticus strain K5 was isolated and analyzed for nucleotide sequence and paired with the expression vector pQE30. The expression vector was transformed into E. coli strain M15, the PirA recombinant protein was expressed in the form of 6xHis-PirA fusion protein of about 15 kDa. PirA recombinant protein was purified and determined the PirAvp binding ratio, cloning and sequencing of PirA gene from Vibrio parahaemolyticus strain K5 causing AHPND by PCR method with specific primers and molecular weights of PirAvp and the PirAvp complex. Results: PirA gene from Vibrio parahaemolyticus strain K5 was cloned into pGEM-T easy vector (Promega, USA) and screened E. coli TOP10 colonies containing pGEM T easy/PirA recombinant plasmid on LB agar/ampicillin/IPTG/X-Gal medium. PCR showing a band of about 347 bp, matching the size of PirA gene and two nucleotide sequences (BamHI and HindIII). The results showed that PirA gene has a length of 336 bp and similar to PirA gene on GenBank (Code: KU556825.1). The results of protein extracted from E. coli M15 recombinant cells and 6xHis-PirA target protein was collected in elution fractions from EF2 to EF6, showed that the concentration of 6xHis-PirA protein and EF3 elution fraction collected a highest protein concentration (1,586.54 µg/ml). Conclusions: The purified PirA recombinant protein will provide materials for development research to create biological products to prevent and treat AHPND.

Objective: The study aimed to provide a picture total of the forest and erosion status of the beach and dykes of Kien Giang and Ca Mau. Theoretical framework: Kien Giang and Ca Mau are located in the West Sea, and in recent years, along the coast of this region, erosion of the coast and sea dykes has been profound. Method: There are 18 sample plots for testing. The map also includes 68 survey plots that are predefined and used as a basis for positioning in the field. The measurement indicators include tree species identification. Results and conclusion: The level of erosion in Ha Tien’s forests varies based on tree density and environmental factors. The forest with no erosion has a thickness of 9,600 trees/ha and a stem diameter of 19 cm, while the extremely erosion forest has 2,000 trees/ha and a stem diameter of 6 cm. Topographically, Ha Tien has little erosion, while U Minh is a low-lying area with high erosion. Erosion levels are 1-2 in January-April, 4-5 in May-October, and 3 in November-December. Currently, the section is divided into 28 sub-sections, with Kien Giang having 23. One sub-section is level 1, 11 sub-sections are level 2, 1 is level 3, 3 are level 4, and 3 are level 5. In Ca Mau, two sub-sections are level 4, and 3 are level 5. Implications of the research: With climate change and rising sea levels, erosion levels tend to increase one level in sub-section areas in the coming years.

Utilizing unmanned aerial vehicles (UAVs) to facilitate wireless communication has emerged as a viable and promising strategy aimed at enhancing both current and prospective wireless systems. This approach offers many advantages by establishing line-of-sight connections, optimizing operational efficiency, and enabling flexible deployment capabilities in various terrains. Thus, in this paper, we investigate UAV communication in a relaying network in which a UAV helps communication between a source and two destination users while flying to a location. To have a complete view of our proposed system, we consider both orthogonal multiple access as OFDM and non-orthogonal multiple access (NOMA) scenarios. Moreover, we apply successive convex optimization (SCO) and the Block-coordinate gradient descent (BCGD) for the sum-rate optimization problems to improve the system performance under constraints of total bandwidth and total power at the ground base station and UAV. The experimental results validate that the achievable secrecy rates are notably enhanced by using our proposed algorithms and show optimal trends for critical parameters, such as transmit powers, the flight trajectory and speed of UAV, and resource allocation of OFDM and NOMA.

Three Dimensional Variational data assimilation or analysis (3DVAR) is one of most classical methods for providing the initial values for numerical models. In this method, the dimensions of the background error covariance and the observational error covariance matrices are large. Therefore, it is difficult to get the inverse of the covariance matrices and to reduce the orders of these matrices without information loss. With the use of the Sylvester Equation, on the basis of a new linear regression, a new cost function for 3DVAR was given. For the first-guess m×n field, there is an approximate 1−(m²+n²)/(mn×mn) reduction with m>1 & n>1 by using the cost function. The results of the numerical experiments show that the effect of this algorithm is no worse than that of the old cost function for 3DVAR.

In nonlinear self-consistent system, Lorenz system (Lorenz equations) is a classic case with chaos solutions which are sensitively dependent on the initial conditions. As it is difficult to get the analytical solution, the numerical methods and qualitative analytical methods are widely used in many studies. In these papers, Runge-Kutta method is the one most often used to solve these differential equations. However, this method is still a method based on explicit time scheme, which would be the main reason for the chaotic solutions to Lorenz system. In this work, numerical experiments based on implicit time scheme and explicit scheme are setup for comparison, the results show that: in implicit time scheme, the numerical solutions (counterexamples) are without chaos; for an original volume, the volume shrinks exponentially fast to 0 in common.

With the continuous improvement and observable benefits of electric vehicles (EVs), major logistic companies are introducing more EVs into their conventional fleets. This gives rise to a new type of vehicle routing problem with mixed vehicles, where heterogeneous internal combustion vehicles (ICVs) and electric vehicles are considered in route planning. In addition, certain deliveries that are not efficient on any type of vehicles, are outsourced to third-party common carriers. In this paper, we define this problem as a mixed vehicle routing problem with common carriers (MVRPC). The objective of such problems is to minimize the transportation costs by considering routes with ICVs and EVs, the possibility of visiting recharging stations, outsourcing options, and drivers’ layover regulations. This variant of the vehicle routing problems has many practical applications, particularly in the design of long-haul transportation and last-mile delivery services. Effective MVRPC solutions play a key role in promoting the going Green image and optimally allocating resources. The problem has received limited attention in the literature likely because addressing all the needed aspects is especially challenging. To solve the large-scale problem, we develop a branch-and-cut pricing framework that relies on strong cuts and customized labeling algorithms. Numerical experiments highlight the effectiveness of our algorithm. This success can be attributed to tailored critical resources, dynamically bounded bidirectional labeling procedures, strong dominance criteria, and implementation strategies.

Nanocomposites of TiO₂ Degussa P25 nanoparticles/activated carbon (TiO₂/AC ) were prepared at various mass ratios of (4:1), (3:2), (2:3), and (1:4) by a facile process. The effects of TiO₂/AC mass ratios on the structural, morphological, and photocatalytic properties were systematically studied in comparison with bare TiO₂ and bare AC. TiO₂ nanoparticles exhibited dominant anatase and minor rutile phases, and a crystallite size of approximately 21 nm; while AC had XRD peaks of graphite and carbon, and a crystallite size of 49 nm. The composites exhibited tight decoration of TiO₂ nanoparticles on micron-/submicron AC particles, and uniform TiO₂/AC composites were obtained as evidenced by the uniform distribution of Ti, O, and C in an EDS mapping. Moreover, Raman spectra show the typical vibration modes of anatase TiO₂ (e.g., E_1g⁽¹⁾, B_1g⁽¹⁾, E_g⁽³⁾) and carbon materials with D and G bands. The TiO₂/AC with (4:1), (3:2), and (2:3) possessed higher reaction rate constants (k) in photocatalytic degradation of methylene blue (MB) than that of either TiO₂ or AC. Among the investigated materials, TiO₂/AC = 4:1 achieved the highest photocatalytic activity with a high k of 55.2×10^-3 min^-1 and an MB removal efficiency of 96.6% after 30 min treatment under UV-Vis irradiation (120 mW/cm²). The enhanced photocatalytic activity for TiO₂/AC is due to the synergistic effect of the high adsorption capability of AC and the high photocatalytic activity of TiO₂. Furthermore, TiO₂/AC promotes the separation of photoexcited electron/hole (e^-/h⁺) pairs to reduce their recombination rate and thus enhance photocatalytic activity. The optimal TiO₂/AC composite in this study can be used for treating industrial or household wastewater with organic pollutants.

Extracts of Cordyceps militaris which possess the bioactive capacity such as antimicrobial activity and DPPH-free radical scavenging capacity, are applied to the serum product. This finished serum product has been evaluated the in vitro bioactivity and the stability with expect to find out a good extract with a suitable percentage used for serum product as natural materials on preservatives and antioxidation.

Artificial Intelligence innovations, such as chatbots and specialized education suggestion tools, provide potential interactive and on-demand pedagogical engagement between non-Christians and Christians with Christianity. However, there is little empirical research on the readiness, acceptance, and adoption of A.I.'s involvement in religious education in a secular state, such as Vietnam. This research addresses the literature gap by providing an entrepreneurial analysis and customer perspectives on the ideas of A.I.'s involvement in religious education. Specifically, the study explores whether the Vietnamese across different ages and religious orientations accept and have enough skills to adopt A.I.'s religious education innovation. The interview sample is 32 participants, selected based on their religious orientation (Christians & Non-Christians) and age (Generation X, Generation Y & Generation Z). Most respondents are open to A.I. application in religious education except for the Church's personnel. However, only gen Z generations are fully prepared to adopt this innovation. Theoretically, the research customizes the Unified Theory of Acceptance and Use of Technology model into religious innovation context. Practically, this research acts as market research on the demand for A.I.'s religious innovation in Vietnam, an insight for future religious tech entrepreneurs.

Global agriculture has been forced to increase food production to feed the growing human population, while confronting various environmental obstacles such as global warming, resistance to pathogens, and constraints on arable land caused by soil salinity, drought, rising sea level, saltwater intrusion, and urbanization. Regarding abiotic stresses, salinity is a worldwide problem for agricultural production. Many efforts, therefore, have been made to cope with the environmental challenges, however, the progress of salinization, which is mainly caused and accelerated by anthropogenic activities, is likely faster than our progress in finding ways to deal with this problem. In addition, drought represents a global threat to the production of major crops. In addition, pests and pathogens cause significant crop losses and diminish global food security. Among the various strategies that have been investigated and applied in plant science, antimicrobial peptides derived from plants have caught widespread attention from scientists since these peptides exhibit beneficial biological activities. In agricultural science, there have been reports on the roles of antimicrobial peptides with active properties against biotic and abiotic stresses. Non-specific plant lipid transfer proteins, thionins, systemins, defensins, cyclotides, and heveins-like antimicrobial peptides are common antimicrobial peptides that have been found to be involved in the defense system against fungi and insect pests. Based on their potential ability to protect crops from pests, bacteria, and pathogenic fungi, the use of antimicrobial peptide genes in creating transgenic plants has been largely conducted during the last decades, and these studies have obtained positive results against the growth of fungi and bacteria. This review will focus on the latest progress in studies of antimicrobial peptides related to biotic and abiotic stress tolerance in plants. We will also update the current progress in the development of antimicrobial peptide-based transgenic crops.

Today, more than 70 million tons of lignin are produced by the pulp and paper industry every year. However, the utilization of lignin as a source for chemical synthesis is still limited due to the complex and heterogeneous lignin structure. The purpose of this study was a selective photodegradation of industrially available kraft lignin in order to obtain appropriate fragments and building block chemicals for further utilization, e.g. polymerization. Thus, kraft lignin obtained from soft wood black liquor by acidification was dissolved in sodium hydroxide and irradiated at a wavelength of 254 nm with and without the presence of titanium dioxide in various concentrations. Analyses of the irradiated products via SEC showed decreasing molar masses and decreasing polydispersity indices over time. At the end of the irradiation period the lignin was depolymerised to form fragments as small as the lignin monomers. TOC analyses showed minimal mineralisation due to the depolymerisation process.

Renal clear cell carcinoma (ccRCC) comprises over 75% of all renal tumors and arises in the epithelial cells of the proximal convoluted tubule. Molecularly ccRCC is characterized by copy number alterations (CNAs) such as the loss of chromosome 3p and VHL inactivation. Additional driver mutations (SETD2, PBRM1, BAP1, and others) promote genomic instability and tumor cell metastasis through the dysregulation of various metabolic and immune-response pathways. Many researchers identified mutation, gene expression, and proteomic signatures for early diagnosis and prognostics for ccRCC. Despite a tremendous influx of data regarding DNA alterations, gene expression, and protein expression, the incorporation of these analyses for diagnosis and prognosis of RCC into the clinical application has not been implemented yet. In this review, we focused on the molecular changes associated with ccRCC development, along with gene expression and protein signatures, to emphasize the utilization of these molecular profiles in clinical practice. These findings, in the context of machine learning and precision medicine, may help to overcome some of the barriers encountered for implementing molecular profiles of tumors into the diagnosis and treatment of ccRCC.

Osteoclasts (OCs) are the multinucleated, bone-resorbing giant cells originally differentiated from a monocyte/macrophage lineage. OC differentiation and maturation, also called osteoclastogenesis, are strictly regulated by a variety of signaling pathways primarily induced by the interactions of two prerequisite cytokines, macrophage colony-stimulating factor (M-CSF) and the receptor activator of nuclear factor-κB ligand (RANKL) to their respective surface receptors, c-fms and RANK, in OC precursors (pre-OCs). Rab11 has emerged as the spatiotemporal regulators of intracellular vesicular transport in the endosomal recycling system; however, how it regulates osteoclastogenesis is incompletely understood. OC-triggered bone resorption is best characterized to be immensely dependent upon lysosomal function, the intracellular acidic organelles containing more than 50 acid hydrolases secreted into bone matrix microenvironment (BME). On the contrary, it is little known about the lysosomal function on modulating the turnover of c-fms and RANK surface receptors via Rab GTPase-mediated vesicular transport, thereby dictating osteoclastogenesis. In this review, I briefly describe the mechanism underlying lysosome-induced osteoclastogenesis via the Rab11-mediated modulation of the surface receptors in OCs.

Initial periods of adsorption kinetics play an important role in estimating the initial adsorption rate and rate constant of adsorption process. Several adsorption processes rapidly occur, and the experimental data of adsorption kinetics under the initial periods can contain potential errors. The pseudo-second-order (PSO) kinetic model has been popularly applied in the field of adsorption. The use of the nonlinear optimization method to obtain the parameters of the PSO model can minimize error functions during modelling compared to the linear method. However, the nonlinear method has limitations in that it cannot directly recognize potential errors in the experimental points of time-dependent adsorption, especially under the initial periods. In this study, for the first time, the different linear types (Types 1–6) of the PSO model are applied to discover the error points under the initial periods. The result indicated that the fitting method using its linear equations (Types 2–5) is really helpful for identifying the error (doubtful) experimental points from the initial periods of adsorption kinetics. The imprecise points lead to low adjusted R2 (adj-R2), high reduced χ2 (red-χ2), and high Bayesian information criterion (BIC) values. After removing those points, the experimental data were adequately fitted with the PSO model. statistical analyses demonstrated that the nonlinear method must be used for modelling the PSO model because its red-χ2 and BIC were lower than the linear method. Type 1 has been extensively applied in the literature because of its very high adj-R2 (0.9999) and its excellent fitting to experimental points. However, its application should be limited because the potential errors from experimental points were not identified by this type. For comparison, the other kinetic models (i.e., pseudo-first-order, pseudo-nth-order, Avrami, and Elovich) are applied. The modelling result using the nonlinear forms of those models indicated that the fault experimental points from the initial periods were not detected.

Floods are among the most serious natural disasters worldwide; they cause enormous crop losses every year and threaten world food security. There are many studies focused on flood impact assessments for administrative districts but fewer on postdisaster impact assessments for specific crops. Therefore, this study used remote sensing data, including the normalized difference vegetation index (NDVI), elevation data, slope data, and rainfall data, combined with crop growing season data to construct a crop flood damage assessment index (CFAI). First, an analytic hierarchy process (AHP) was used to assign weights to the impact factors; then, the weighted composite score method was used to calculate the CFAI; and finally, the impact was classified as slight, moderate, or severe based on the magnitude of the CFAI . This method was used for the Missouri River floods of 2019 in the U.S. Due to the lack of measured data, the disaster vegetation damage index (DVDI) was used to validate the results. The combined approach achieved a high degree of consistency in spatial distribution. The CFAI can respond well to the degree of crop impact after flooding, providing new ideas and reference standards for agriculture-related departments.

Saltwater intrusion in the rapidly developing city of Da Nang in central Vietnam is currently causing various water-related challenges, including inadequate water supply and water pollution. An integrated SWAT-MODFLOW numerical model was used to investigate the origin and mechanism of saltwater in Holocene and Pleistocene aquifers. Geophysical and isotopic approaches were used to validate the SEAWAT model applied for simulating saltwater intrusion. The results suggest that the ebb and flow of tides, as well as water levels in rivers primarily impact coastal aquifers. However, effective water resource planning and management, along with maintaining the natural recharge of fresh water from local rain during the rainy season, could enable the rational and efficient utilization of groundwater, reducing saltwater intrusion in many areas. During the dry season, groundwater is recharged from higher altitude areas. The current saltwater intrusion mainly occurs along the rivers up to the hydraulic dam. Simulated models, using scenarios of stop abstracting groundwater, but changing to the use of surface water for drinking water, show that the area of saline water shrinks quickly after 30 years, reducing from 59.6 km2 to 39.5 km2 and from 40.2 km2 to 28.6 km2 in Holocene and Pleistocene, respectively.

The Ca Mau Peninsula situated in the Mekong Delta of Vietnam, features a low-lying terrain. Over recent years, the region has encountered the adverse impacts of climate change, leading to both land subsidence and rising sea levels. In this study, we assessed the land subsidence susceptibility in the Ca Mau peninsula utilizing three Boosting machine learning models: AdaBoost, Gradient Boosting, and Extremely Gradient Boosting (XGB). Eight key factors were identified as the most influential in land subsidence within Ca Mau: land cover (LULC), Groundwater levels, distance to roads, Digital Terrain Model (DTM), normalized vegetation index (NDVI), geology, soil composition, and proximity to rivers and streams. A dataset comprising 1950 subsidence sample points was employed for the model, with 1910 points obtained from the PSInSAR Radar method, and the remaining points derived from leveling measurements. The sample points were split, with 70% allocated to the training set and 30% to the testing set. Following computation and execution, the three models underwent evaluation for accuracy using statistical metrics such as the ROC curve, Area under the curve (AUC), Specificity, Sensitivity, and Overall Accuracy. The research findings revealed that the XGB model exhibited the highest accuracy, achieving an AUC above 0.9 for both the training and test sets. Consequently, XGB was chosen to construct a land subsidence susceptibility map for the Ca Mau peninsula.

To solve the problem of energy constraint and spectrum scarcity for cognitive radio wireless sensor networks (CR-WSNs), an underlay decode-and-forward relaying scheme is considered, where the energy constrained secondary source and relay nodes are capable of harvesting energy from a multi-antenna power beacon (PB) and using that harvested energy to forward the source information to the destination. Based on the time switching receiver architecture, three relaying protocols, namely, hybrid partial relay selection (H-PRS), conventional opportunistic relay selection (C-ORS), and best opportunistic relay selection (B-ORS) protocols are considered to enhance the end-to-end performance under the joint impact of maximal interference constraint and transceiver hardware impairments. For performance evaluation and comparison, we derive exact and asymptotic closed-form expressions of outage probability (OP) and throughput (TP) to provide significant insights into the impact of our proposed protocols on the system performance over Rayleigh fading channel. Finally, simulation results validate the theoretical results.

Viruses can induce the fusion of infected and neighboring cells, leading to the formation of syncytia. Cell-cell fusion is mediated by viral fusion proteins on the plasma membrane of infected cells that interact with cellular receptors on neighboring cells. Viruses use this mechanism to spread rapidly to adjacent cells or escape host immunity. For some viruses, syncytium formation is a hallmark of infection and a known pathogenicity factor. For others, the role of syncytium formation in viral dissemination and pathogenicity remains poorly understood. Human cytomegalovirus (HCMV) is an important cause of morbidity and mortality in transplant patients and the leading cause of congenital infections. Clinical HCMV isolates have broad cell tropism but differ in their ability to induce cell-cell fusions, and little is known about the molecular determinants. We developed a system to analyze HCMV glycoprotein B (gB) variants in a defined genetic background. HCMV strains TB40/E and TR were used as vectors to compare the fusogenicity of six gB variants from congenitally infected fetuses with those from three laboratory strains. Five of them conferred the ability to induce fusion of MRC-5 human embryonic lung fibroblasts to one or both backbone strains, as determined by a split GFP-luciferase reporter system. The same gB variants were not sufficient to induce syncytia in infected ARPE-19 epithelial cells, suggesting that additional factors are involved. The system described here allows a systematic comparison of the fusogenicity of viral envelope glycoproteins and may help to clarify whether fusion-promoting variants are associated with increased pathogenicity.

The Cauto River Basin (CRB), the heartland of Cuban agriculture, has been hit hard by drought and water shortage. In response to this pressing issue, this study provides a comprehensive as-sessment of water supply, demand and balance within the Cauto River Basin, considering the baseline and projected socio-economic and climatic conditions by coupling of SWAT and WEAP models. The obtained results reveal that the annual flow in the CRB is projected to slightly de-crease (2.5%) in which the reduction in the rainy season (3.1%) is higher than that in the dry sea-son (1.3%). Total water demand in the baseline scenario is around 1.194 billion m3, dominated by agriculture (96%), with rice crop requiring nearly half. For the future scenario of 2050, the study shows a 16.6% surge in demand to 1.394 billion m3, driven by climate change and agricultural expansion. However, domestic use decreases by 10% due to population reduction. Water deficit in the future is projected to increase by 52% from 172.4 to 262.7 million m3 due to rising water demand and declining water supply. This study shows that integrating a hydrological model into a water allocation model is a promising approach to estimate the water supply, demand and balance, which is a crucial component of water resources management.

This study was conducted to investigate the status of regional linkage in tourism development in in the Midlands and Northern Mountains of Vietnam. The data was collected from a survey of 755 people, including officials from State management bodies in charge of tourism, officials and staffs at tourism resorts, tourism firms, tourism scientists and tourists. In addition, we conducted 10 group discussions, interviewed 30 State tourism agency officials and tourism firms in the Midland and Mountainous provinces of Vietnam. The results show that tourism development in Vietnam in general and the Northwest region in particular is extremely fragmented, not yet forming a regional linkage; Regional and national tourism development programs are just formalistic. The main cause of the situation is the limited regional integration policy in Vietnam, the lack of appropriate regional governance mechanisms and inactive participation of the private sector in regional integration. Based on the findings, we propose a tourism sector linkage model; besides, policy implications are given for fulfilling the linkage policy in the Midlands and Northern Mountains area.

Large-scale crowd phenomena are complex to model because the behaviour of pedestrians needs to be described at both strategic, tactical, and operational levels and is impacted by the density of the crowd. Microscopic models manage to mimic the dynamics at low densities, whereas mesoscopic models achieve better performances in dense situations. This paper proposes and evaluates a novel agent-based architecture to enable agents to dynamically change their operational model based on local density. The ability to combine microscopic and mesoscopic models for multi-scale simulation is studied through a use case of pedestrians at the Festival of Lights, Lyon, France. Pedestrian outflow data is extracted from video recordings of exiting crowds at the festival. The hybrid model is calibrated and validated using a genetic algorithm that optimizes the match between simulated and observed outflow data. Additionally, a local sensitivity analysis is then conducted to identify the most sensitive parameters in the model. Finally, the performance of the hybrid model is compared to different models in terms of density map and computation time. The results demonstrate that the hybrid model has the capacity to effectively simulate pedestrians across varied density scenarios while optimizing computational performance compared to other models.

Better understanding of the quality of life among nursing home residents with dementia is im-portant for developing interventions. The objectives of this cross-sectional study were to examine factors associated with poor health-related quality of life in older adults with dementia living in nursing homes in Hanoi, Vietnam. In-person interviews were conducted with 140 adults 60 years and older with dementia and information about their quality of life was obtained using the Quality of Life in Alzheimer’s Disease scale (QOL-AD). A number of sociodemographic and clinical factors associated with poor health-related quality of life (lowest tertile) were assessed through the results of physical tests, interviews with nursing home staff, and review of medical records. The average age of the study sample was 78.3 years, 65% were women, and their av-erage QOL-AD total score was 27.3 (SD = 4.4). Malnutrition, total dependence in activities of daily living, and urinary incontinence were associated with poor quality of life after controlling for multiple potentially confounding factors. Our findings show that Vietnamese nursing home residents with dementia have a moderate quality of life and interventions based on comprehen-sive geriatric assessment remain needed to modify risk factors associated with poor health-related quality of life.

The emergence of the Covid-19 pandemic has created both negative and positive changes, including implementing the circular economy across the globe. This Systematic Review follows the PRISMA statement and employs the Text Mining (Voyant Tools) technique to visualize and analyze the impacts of the Covid-19 on three aspects of the circular economy: economic, social, and environmental. The research employs Latent Dirichlet Allocation (LDA) to identify five major topics: (1) Shortage of medical equipment but high medical waste during Covid-19 due to the high demand in healthcare; (2) The long term negative impacts of lockdown on economic and social activities because of Covid-19 pandemic; (3) The reports on impacts of Covid-19 pandemic on the manufacturing globally, and their coping strategies and new opportunities; (4) The impacts of international restriction on the tourism, trade, shipping, and aviation industry, causing billion-dollar losses; (5) The reduction of pollution with health environment improvements with example cases from China and EU. The research identifies current literature gaps in the circular economy and Covid- 19 topics and encourages the application of text mining tools into researching to stimulate the research process and assist in communicating with the public.

To have a better protection, strong toughness and good flexibility, all lives and plants must have skins, similarly, all books should have covers. In this paper, considering interlayer friction as a perturbation, we formulate a hardcover-book-like laminated plates with internal friction. For a quasi-static problem, detail analysis on the bending response and energy dissipation are carried out for a three-point-supported plates. Our numerical investigations show that the hardcover is more essential than the core layers in terms of bending response, and the energy dissipation within per loading-unloading cycle can be made to vary by a considerable amount. The central goal of studying is not only to predict the bending deformation of the book-like-plates, but also as a representative case to help finding some clue on the universal behaviours of multilayered architectures with internal friction.

In recent years, the rapid development of computer-aided planning and design technology has provided a new perspective for the study of complex problems such as the generation of architectural complex forms. This study focuses on how to apply parameterization technology to analyze and articulate traditional spatial form composition rules, aiming to minimize reliance on subjective human judgment in the protection and renewal design of the historical style of traditional villages. It aims to establish digital generative design tools to address the challenges of accurately inheriting and innovatively utilizing historical and cultural information in traditional settlements. It introduces how to rely on parameterization technology to analyze the spatial form composition rules, parameter extraction rules, and spatial reconstruction rules of traditional villages, facilitating the complete process from spatial features to parameterization rules, and then to the application of computational methods to deduce spatial features. It also includes case studies demonstrating the application of parameterization technology tools for village protection and explores the role of generative design tools in preserving the spatial style of these settlements.

This paper introduces an advanced method that integrates contingent valuation and machine learning (CVML) to estimate residents’ demand for reducing or mitigating environmental pollutions and climate change. To be precise, CVML is an innovative hybrid machine-learning model, and it can leverage a limited amount of survey data for prediction and data enrichment purposes. The model comprises of two interconnected modules: Module I, an unsupervised learning algorithm, and Module II, a supervised learning algorithm. Module I is responsible for grouping the data into groups based on common characteristics, thereby grouping the corresponding dependent variable, whereas Module II is in charge of demonstrating the ability to predict and the capacity to appropriately assign new samples to their respective category based on input attributes. Take a survey on the topic of air pollution in Hanoi in 2019 as an example, we found that CVML can predict households’ willingness– to– pay for polluted air mitigation at a high degree of accuracy (i.e., 98%). We found that CVML can help users reduce costs or save resources because it makes use of secondary data that is available on many open data sources. These findings suggest that CVML is a sound and practical method that could be widely applied in a wide range of fields, particularly environmental economics and sustainability science. In practice, CVML could be used to support decision-makers in improving the financial resources to maintain and/or further support many environmental programs in years to come.

Single-layer core corrugated sandwich panels generally consist of a corrugated core and two layers of panels, while multi-layer core corrugated sandwich panels are formed by stacking multiple layers of panels with multiple layers of core layers. In this study, integrated multilayer core corrugated sandwich panels with different shapes of corrugated cores (triangular, trapezoidal, and rectangular) and the different number of core layers were fabricated using 3D printing technology, and the mechanical behavior of such multilayer core corrugated sandwich panels under quasi-static three-point bending was investigated using experiments and numerical simulations. The effects of core shape and number of core layers on the bending deformation process, damage mode, load carrying capacity, and bending energy dissipation capacity of multilayer core sandwich panels are discussed. Parametric design of multilayer triangular core corrugated sandwich panels was also carried out by finite element software ABAQUS. It was found that a new multilayer corrugated sandwich panel with a multi-layer core is better than the single core shape multilayer corrugated sandwich panel in terms of bending load capacity, energy dissipation capacity and deformation capacity can be obtained through the combination design of different core shapes.

The pursuit of sustainable wellbeing is one of the research objectives of positive experience design. Driven by this goal, the purpose of this paper is to provide an impact-centered sustainable positive experience design model. Firstly, the literature review method was used to define the research status and concept of impact-centered sustainable design. Secondly, an impact-centered sustainable positive experience design model was constructed, and relevant formulas for concept generation and concept evaluation were proposed. Thirdly, design verification was conducted through a workshop. Finally, the Technology Acceptance Model (TAM) questionnaire was used to evaluate and discuss the design model. An impact-centered sustainable positive design model was proposed, which includes the important impact dimensions of sensory experience and meaningful experience on users’ quality of life at different levels: healthy living (pleasure index, health behavior), harmonious community (social connectivity, social contribution), and livable environment (living environment, environmental contribution). Based on positive experience related theory, this study takes long-term impacts as the starting point for sustainable positive experience design, which helps designers to generate design concepts from a systematic and long-term perspective.

Intestinal commensal microbes, called the gut microbiota, play a critical role in host immune homeostasis through active microbial metabolites and innate and adaptive immune responses. Dysbiosis or imbalance of the gut microbiota composition is associated with inflammatory bowel disease (IBD) which includes Crohn’s disease and ulcerative colitis. The incidence and prevalence rates of IBD have been increasing worldwide. It is well recognized that butyrate, a microbial metabolite of diet fibers, is a major energy source for colonocytes and plays a crucial role in regulating immune function and maintaining epithelial barrier function and intestinal homeostasis. Emerging evidence suggests that butyrate might be a potential therapeutic agent to treat IBD. In this review, we discuss about gut microbial metabolites, particularly butyrate, the synthesis and metabolism of butyrate, mechanisms of butyrate in immune and epithelial barrier function. Furthermore, we review the current research on various therapeutic implications of butyrate in IBD.

Child sexual abuse inflicts lifelong devastating consequences for victims and is an ongoing social concern. In most countries, child sexual abuse material (CSAM) distribution is illegal. As a result, there are many research papers in the literature which proposed technologies to detect and investigate CSAM. In this survey, a comprehensive search of the peer-reviewed journal and conference paper databases (including preprints) is conducted to identify high-quality literature. We use the PRISMA methodology to refine our search space to 2,761 papers published by Springer, Elsevier, IEEE and ACM. After iterative reviews of title, abstract and full text for relevance to our topics, 43 papers are included for full review. Our paper provides a comprehensive synthesis of the tasks of the current research and how the papers use techniques and datasets to solve their tasks and evaluate their models. To the best of our knowledge, we are the first to focus exclusively on online CSAM detection and prevention with no geographic boundaries, and the first survey to review papers published after 2018. It can be used by researchers to identify gaps in knowledge and relevant publicly available datasets that may be useful for their research.

As the embedded device and internet of things (IoTs) concept prevalent in today's world, there is an increasing demand for the security and performance requirements on deploying these devices to private and public sectors. The crucial part of it is to protect privacy, confidentiality and integrity, meanwhile, maintain an adequate level of performance during transmission, storage and access of critical information. While the conventional cryptography methods, such as the Advanced Encryption Standard (AES), SHA$-$2 hashing method and RSA and Diffie Hellman for message authentication and identification, work well on systems which have reasonable processing power and memory capabilities. These do not scale well into a world with embedded systems and sensor networks, in conjunction with their nature of smaller size and lower cost. Thus, in the context of resource constrained device, lightweight cryptography methods are proposed to overcome many of the problems of conventional cryptography possessed. This includes constraints related to physical size, processing requirement, memory limitation, energy drain and production cost. This paper provides a survey of the architectures that are defined as replacements for conventional ciphers within an IoTs space and discuss some trends in the design of future lightweight algorithms. The performance metrics are carefully chosen to reflect and assess the suitability for embedded devices. The aim of this research is to identify the various performance metrics applied on different types of symmetric block ciphers especially lightweight ciphers and compare the results on versatile platforms with stream ciphers and public key methods. The comparative analysis on efficient LW cipher will be tested against other similar block ciphers on both MacBook Pro with Intel core and resource constrained device Raspberry Pi with ARM processor.

In the context of intelligent and integrative lighting, in addition to the need for color quality and brightness, the non-visual effect is essential. This refers to the retinal ganglion cells (ipRGCs) and their function, first proposed in 1927. The melanopsin action spectrum has been published in CIE S 026/E: 2018 with the corresponding melanopic equivalent daylight (D65) illuminance (mEDI), melanopic daylight (D65) efficacy ratio (mDER) and 4 other parameters. Due to the importance of mEDI and mDER, this work synthesizes a simple computational model of mDER as the main research objective, based on a database of 4214 practical spectral power distributions (SPDs) of daylight, conventional, LED, and mixed light sources. In addition to the high correlation coefficient R2 of 0.96795 and the 97% confidence offset of 0.0067802, the feasibility of the mDER model in intelligent and integrated lighting applications has been extensively tested and validated. The uncertainty between the mEDI calculated directly from the spectra and that obtained by processing the RGB sensor and applying the mDER model has reached ± 3.3% after an appropriate matrixing process and proper illumination characterization combined with the successful mDER calculation model. This result opens the potential of low-cost RGB sensors for applications in intelligent and integrative lighting systems to optimize and compensate the non-visual effective parameter mEDI using daylight and artificial light in indoor spaces. The goal of the research on RGB sensors and the corresponding processing method are also presented and their feasibility is methodically demonstrated. A comprehensive investigation with a huge amount of color sensor sensitivities is necessary in a future work of other researches.

In the field of quality control, the critical challenge of analyzing microdefects in steel filament holds significant importance. This is particularly vital as steel filaments serve as reinforced fibers in the use and applications within various component manufacturing industries. This paper addresses the crucial requirement of identifying and investigating microdefects on steel filaments. Eddy current signals are used for the identification of microdefects, and an in-depth investigation is conducted. The core objective is to establish the relationship between the depth of defects and the signals detected through the eddy current sensing principle. The threshold of eddy current instrument was set at 10%, corresponding to a created depth of 20 µm, to identify defective specimens. A total of 30 defective samples were analyzed, and the phase angles between the experimental and theoretical results were compared. The depths of defects ranged from 20 to 60 µm, with one sample having a depth exceeding 75 µm. The calculated threshold of 10.18% closely aligns with the set threshold of 10%, with a difference of only 1.77%. The resulting root mean square error (RMSE) was found to be 10.53 degrees, equivalent to 3.49 µm for the difference in depth and phase between measured results and estimated results. This underscores the methodology's accuracy and its applicability across diverse manufacturing industries.

In this study, a preload monitoring method using impedance signatures obtained from a piezoelectric-based smart interface is presented for bolted girder connections. Firstly, the background theory of the piezoelectric-based smart interface and its implementation into health monitoring of bolted connections are outlined. A simplified electro-mechanical (EM) impedance model of a smart interface-embedded bolted connection system is formulated to interpret mechanistic understanding of EM impedance signatures under the effect of bolt preload. Secondly, finite element modeling of a bolted connection is carried out to show the numerical feasibility of the presented method and to predetermine the sensitive frequency band of impedance signatures. Finally, impedance measurements are conducted on a lab-scaled bolted girder connection to verify the predetermined sensitive frequency range and to assess the bolt preload changes in the test structure.

Purpose: To clarify the mechanism of state anxiety on intertemporal decision-making, two studies were conducted to investigate the role of trait anxiety and inhibitory control. Study 1 examined the moderating effect of trait anxiety. Study 2 continued to investigate the mediating effect of inhibition control on the basis of study 1. Methods: A total of 266 Chinese college students participated. Participants’ state anxiety, trait anxiety and intertemporal decision-making were measured by questionnaires (scales) respectively. And inhibition control was evaluated by two-choice oddball paradigm. Results: The results of Study 1 indicated that state anxiety could predict intertemporal decision-making and that the moderating effect of trait anxiety on this relationship was significant. Study 2 found that inhibitory control could completely moderate the relationship between state anxiety and intertemporal decision-making and that this indirect effect was affected by trait anxiety. Conclusion: 1)Individuals with higher trait anxiety are more inclined to make more impulsive and intertemporal decisions when they have a high level of state anxiety; 2)state anxiety allows inhibitory control ability to have a further effect on intertemporal decision-making; and 3)the higher trait anxiety in individuals, the stronger mediating effect of inhibitory control on the relationship between state anxiety and intertemporal decision-making.

In recent years, drones have been used in a wide range of fields such as agriculture, transportation of goods, and security. Drones equipped with communication facilities are expected to play an active role as base stations in areas where ground base stations are unavailable, such as disaster areas. In addition, asynchronous operation is being considered for local 5G in order to support all kinds of use cases. In asynchronous operation, cross-link interference between base stations is an issue. This paper attempts to reduce the interference caused by the drone network by introducing circularly polarized antennas. Numerical analyses are conducted to validate the effectiveness of the proposed system, where SIRs (Signal-to-Interference Ratio) are shown to be improved significantly as the numerical evaluation results.

Non-Orthogonal Multiple Access (NOMA) is the key technology promised to be applied in next-generation networks in the near future. In this study, we propose a multi-points cooperative relaying (MPCR) NOMA model instead of just using a relay as the previous studies. Based on the channel state information (CSI), the base station (BS) selects a closest user equipment (UE) and sends a superposed signal to this UE as a first relay node. We have assumed that there are N UEs in the network and Nth UE, which is farthest from BS, has the poorest quality signal transmitted from the BS compared other UEs. Nth UE received the forwarded signal from N-1 relaying nodes that are UEs with better signal quality. At the ith relaying node, it detect its own symbol by using successive interference cancellation (SIC) and will forward the composite signal to the next closest user, namely i+1th UE, and include an excess power which will use for energy harvesting (EH) intention at the next UE. By these, the farthest UE in network can be significantly improved. In addition, closed-form expressions of outage probability for users over both the Rayleigh and Nakagami-m fading channels are also presented. Analysis and simulation results performed by Matlab software which are presented accurately and clearly show that the effectiveness of our proposed model and this model consistents with the multi-access wireless network in future.

This article conducts a bibliometric analysis focusing on the influence of globalization and technology in the academic context. Previous studies have focused on analyzing the relationship between the number of research citations and international collaboration, but no study has explored it in the scope of consumer behavior and retail. Leveraging the Scopus database, the research analyzes a significant corpus of 2,111 documents from 1971 to 2022. The findings reveal a distinct surge in academic output related to the topic of technology, reflecting a growing interest in understanding the interaction between technological factors and consumer behavior. The study also explores trends in international collaboration in publications as well as its impact on citation counts.

Recommender systems have been applied in a wide range of domains such as e-commerce, media, banking, and utilities. This kind of system provides personalized suggestions based on large amounts of data in order to increase user satisfaction. These suggestions help client select products, while organizations can increase the consumption of a product. In the case of social data, sentiment analysis can help gain better understanding of a user’s attitudes, opinions and emotions, which is beneficial to integrate in recommender systems for achieving higher recommendation reliability. On the one hand, this information can be used to complement explicit ratings given to products by users. On the other hand, sentiment analysis of items that can be derived from online news services, blogs, social media or even from the recommender systems themselves is seen as capable of providing better recommendations to users. In this study, we present and evaluate a recommendation approach that integrates sentiment analysis into collaborative filtering methods. The recommender system proposal is based on an adaptive architecture, which includes improved techniques for feature extraction and deep learning models based on sentiment analysis. The results of the empirical study performed with two popular datasets show that sentiment–based deep learning models and collaborative filtering methods can significantly improve the recommender system’s performance.

The TiO₂ nanostructures resulted by pyrolysis of TiCl₄ at low temperature of 80 ^oC are found to be a mixture of amorphous TiO₂ complexes and anatase nanostructure whose ratio depends on the pH of the pyrolysis medium. At low pH level, the resulting TiO₂ nanostructure is predominant anatase and gradually shifts to the amorphous TiO₂ complexes with pH level increasing. By means of heat treatment, the amorphous TiO₂ complexes can be converted back to the anatase nanostructure and then transform to rutile with the elevating temperature. Amongst of the TiO₂ nanostructure recovered from amorphous TiO₂ complexes, the anatase shows to be the most effective photocatalyst in decomposition of methylene blue.

Porous tantalum (Ta) is a promising biomaterial and has been applied in orthopedics and dentistry for nearly two decades. The high porosity and interconnected pore structure of porous Ta promise fine bone ingrowth and new bone formation within the inner space, which further guarantee rapid osteointegration and bone-implant stability in long term. Porous Ta has high wettability and surface energy that can facilitate adherence, proliferation and mineralization of osteoblasts. Meanwhile, low elastic modulus and high friction coefficient of porous Ta can effectively avoid stress shield effect, minimize marginal bone loss and ensure primary stability. Accordingly, the satisfactory clinical application of porous Ta based implants or prostheses are mainly derived from its excellent biological and mechanical properties. With the advent of additive manufacturing, personalized porous Ta based implants or prostheses have shown their clinical value in the treatment of individual patient who need specially designed implant or prosthesis. In addition, many modification methods have been introduced to enhance the bioactivity and antibacterial property of porous Ta with promising in vitro and in vivo research results. In any case, choosing suitable patients is of great importance to guarantee surgical success after porous Ta insertion.

AISI 1050 steel circular pocket milling under minimum quantity lubrication (MQL) surroundings including nozzle elevation angle, lubricant flow rate, air pressure and cutting speed was studied. The machined surface quality (Ra) was evaluated for Up-milling side and Down-milling side. In this study, to obtain an manifest explanation on the pivotal effective parameters of MQL surroundings and cutting speed on the machined surface quality (Ra) through analyzing Taguchi L9 (34-2) approach and ANOVA calculation to identify those parameters, by utilizing the experimental outcomes to interpret three-dimensional (3D) surface plots and the diagrams of Signal-to-Noise ratios and major impact plots of Mean. The obtained outcomes of optimal operating parameters indicated that the pivotal effective parameters of MQL surroundings are nozzle elevation angle and lubricant flow rate on the machined surface quality. Simultaneously, a quadratic mathematical paradigm generated by using response surface design (RSD) and desirableness function evaluation were utilized to forecast the optimal values of the machined surface quality compared to Taguchi method. The results unveiled that the optimal values of the machined surface quality are adjacent to experimental attained values. The machined surface quality has been significantly improved using MQL surroundings.

Abstract. This paper proposes a Second Order Terminal Sliding Mode (2TSM) approach to the trajectory tracking of Differential Drive Mobile Robot (DDMR). Within this cascaded control scheme, the 2TSM dynamic controller, at the inner most loop, tracks the robot’s velocity quantities; while a kinematic controller, at the outer most loop, regulates the robot’s positions. In this manner, chattering is greatly attenuated and finite time convergence is guaranteed by the second order TSM manifold which involves higher order derivatives of the state variables, resulting in inherently robust as well as fast and better tracking precision. The simulation results demonstrate the merit of the proposed control methods.

Facing with errors of a product after machining was a big title in this field. That will affect to product’s quality with unpredictable situation when products is in use for some particular application such as in medical facilities. Improving the precision of machine tools by exploring temperature on multiple points and measuring differential locations of the spindle is going to be executed in this study. A temperature measurement tool and a software running on Windows platform have been developed and combining with Non-bar system in order to support analyzing the temperature rising with the changes of length of the spindle to find the compensation solution based on eccentricity and length distortion. In this study, the whole tests have done on UX300 five – axis CNC machine tools for this investigation and the errors after applying compensation function have reduced 70% at least, with respect to the errors after machining without using compensation function.

Head and neck squamous cell carcinoma (HNSCC) is a type of cancer that arises from the epithelium lining of the oral cavity, hypopharynx, oropharynx, and larynx. Despite advancement of the current treatment to HNSCC, such as surgery, chemotherapy, and radiotherapy, the overall survival rate of HNSCC remains poor due to late diagnosis and acquired resistance to treatment. Natural products have been extensively explored as a safer and more acceptable alternative to current treatments, with numerous studies displaying their potential against HNSCC. This review highlights preclinical studies in the past 5 years involving natural products against HNSCC and explores the signalling pathways altered by these products. This review also addresses challenges and future directions of the use of natural products as chemotherapeutic and chemoprevention agents against HNSCC.

Arylsulfatase and β-glucuronidase are two important enzymes in human, which play important role on dynamic equilibrium of steroidal estrogens. This work probably for the first time reported that hydrogen peroxide (H2O2), hypochlorite and peracetic acid (PAA) could effectively inhibit the activities of arylsulfatase and/or β-glucuronidase. The 50 percent of inhibitions (IC50) of H2O2, and PAA on arylsulfatase were found to be 142.90±9.00, 91.83±10.01, and 43.46±2.92 μM, respectively. The corresponding respective IC50 of hypochlorite and PAA on β-glucuronidase were 704.90±41.40 and 23.26±0.82 μM, while H2O2 showed no inhibition on β-glucuronidase. It was further revealed that the inhibition of hypochlorite on both arylsulfatase and β-glucuronidase was irreversible. On the contrary, the inhibition by H2O2 and PAA was reversible. Moreover, it was found that the inhibitions of arylsulfatase and/or β-glucuronidase by these three chemicals were pH-dependent, among which the inhibition by H2O2 was competitive and non-competitive for PAA. In general, H2O2 and hypochlorite can be endogenously produced in human, which suggested that the two compounds are potential endocrine disruption compounds (EDCs) as they can cause endocrine disruption via inhibition of arylsulfatase and β-glucuronidase. This work further indicated that any agent that can induce production of H2O2 or hypochlorite in human is potential EDC, which explains why some EDCs with very weak or no estrogenic potency can cause endocrine disruption that confirmed in epidemiological studies.

Chromophobe renal cell carcinoma (chRCC) and oncocytoma (RO) are renal tumor types originating from alpha intercalated cells of the collecting ducts of the kidney. Both tumor types have similar gross histological morphology and increased mitochondria, which leads to difficulties differentiating between these tumors, especially with core biopsy samples. This study aims to apply a machine learning approach to develop a molecular classifier based on transcriptomics data. Here we generated a meta-data set containing 62 chRCC and 45 RO gene expression arrays. Arrays were subjected to quality control steps, and genes were selected based on differential expression and ROC analysis. The final gene list was evaluated with UMAP based dimension reduction followed by density-based clustering with 95.5% accuracy. Molecular profiling by KEGG pathway analysis identified enrichment of fatty acid oxidation pathway in RO. We finally identified and validated the 30-gene signature, with an accuracy of 94.4% to distinguish chRCC from RO on UMAP analysis. Our results show that chRCC and RO have a distinct gene signature that can differentiate these tumors and complement histology for routine diagnosis of these two tumors.

As a renewable industrial crop, Miscanthus offers numerous advantages, namely high photosynthesis activity (as a C4 plant) and exceptional CO2 fixation rate. These properties make Miscanthus very attractive for industrial exploitation, such as lignin generation. Here, we present a systematic study analyzing the correlation of the lignin structure with Miscanthus genotype and plant portion (stem versus leaf). Specifically, the ratio of the three monolignols and corresponding building blocks as well as the linkages formed between the units have been studied. Depending on the Miscanthus genotype and plant component (leaf versus stem), correlations between chemical structure and properties of the lignins have been determined, i.e. correlations in molecular weight, polydispersity and decomposition temperature. Lignin isolation was performed using non-catalyzed organosolv pulping and the structure analysis includes NREL, FTIR, UV-Vis, HSQC-NMR, TGA, pyrolysis GC/MS. Structural differences were found for stem and leaf-derived lignins. Compared to beech wood lignins, Miscanthus lignins possess lower molecular weight and narrow polydispersities (< 1.5 Miscanthus vs. > 2.5 beech) corresponding to improved homogeneity. In addition to conventional univariate analysis of FTIR spectra, multivariate chemometrics revealed distinct differences for aromatic in-plane deformations of stem versus leaf-derived lignins. These results emphasize the potential of Miscanthus as low-input resource and Miscanthus-derived lignin as promising agricultural feedstock.

Bioethanol has been considered as an excellent alternative to fossil fuels since it importantly contributes to the reduced consumption of the crude oil and to the alleviation of environmental pollution [1]. Up to now, the baker yeast Saccharomyces cerevisiae is the most common eukaryotic microorganism used in ethanol production. The inability of S. cerevisiae to grow on pentoses, however, hinders its effective growth on plant biomass hydrolysates, which contain large amounts of C5 and C12 sugars. The industrial-scale bioprocessing requires high temperature bioreactors, diverse carbon sources, and the high titer production of volatile compounds [2]. These criteria indicate that the search for alternative microbes possessing useful traits that meet the required standards of bioethanol production is necessary. Compared to other yeasts, Kluyveromyces marxianus has several advantages over the others, e.g. it could grow on a broad spectrum of substrates (C5, C6 and C12 sugars) [3], tolerate to high temperature, toxin [4,5] and a wide range of pH values [6], and produce volatile short-chain ester [2]. K. marxianus also shows a high ethanol production rate at high temperature and is a Crabtree-negative species [7]. These attributes make K. marxianus a promise as an industrial host for the biosynthesis of biofuels and other valuable chemicals.

Aim at a better understanding of the flow field around a fully appended Joubert BB2 submarine model and complementing the experimental investigations of the wake of the hydroplanes and sail, the Large eddy simulation (LES) with the dynamic Smagorinsky model is conducted. Three sets of grids with a maximum grid number of up to 228 million are designed, to perform the LES simulation for the Joubert BB2 at 10° yaw conditions, with a freestream Reynolds (Re) number based on the local freestream velocity and the hull length of ReL=2.2×107. And comparison of the wake of the cruciform appendage is made with experiments, to verify the computational accuracy and examine the influence of the spatial resolution. A satisfactory result shows more favorable agreement with experimental measurements as the improvement of spatial resolution, with the relative error of the vortice centers well within 7.2% in the most refined grid arrangement. And under this grid arrangement, the evolution characteristics of three co-rotating vortices originating from the cruciform appendage are further described in detail at straight ahead and 10° yaw conditions.

Background. To describe the characteristics of anterior mediastinal masses on conventional magnetic resonance imaging (MRI) and to assess the role of the Apparent Diffusion Coefficient (ADC) value in distinguishing benign from malignant mediastinal lesions. Methods. We conducted a retrospective cross-sectional study on 55 patients with anterior mediastinal mass who performed MRI before treatment. Biopsy and histopathological assessments were done after that. A radiologist evaluates the changes of signal intensity on these sequences: T1- weighted VIBE DIXON pre and post-contrast with Gadolinium, T2 HASTE, T2 TIRM, DWI/ADC, to determine the size, margin of the lesion, the presence of fat, cystic in it. ADCs values were calculated from the ADC maps which were constructed from b = 0 and b = 2000 Results. The study was composed of 55 patients, with 5 benign lesions and 50 malignant lesions. The ADCmean, ADCmedian, ADC10, and ADC90 in the histogram-based approach and hot-spot-ROI-based mean ADC for the malignant lesions was significantly lower than those found in benign lesions (P-value <0.05). The hot-spot-ROI-based mean ADC had the highest value in differentiation between benign and malignant mediastinal lesions, between group A (benign lesions, thymoma A, AB, B1) and group B (thymoma B2, B3 and other malignant lesions). The cut-off point of the ADC value differentiating malignant from benign mediastinal lesions was 1,17x10-3mm2/s with sensitivity of 80%, and specificity of 80%. The cut off point of the ADC value differentiating group A from group B was 0.99 x10-3mm2/s with sensitivity of 78,4%, and specificity of 88.9%. The cut-off point of the ADC value differentiating lymphoma from other malignant lesions was 0,91 x10-3mm2/s with sensitivity of 100%, and specificity of 60.5%. Conclusion. Diffusion-weighted MRI and measurement of ADC value in histogram-based approach and hot-spot-ROI-based mean ADC are very helpful in the differentiation between benign and malignant anterior mediastinal lesions.

Soil sodicity is a major constraint to seedling emergence and crop production, potentially reducing plant growth due to physical and chemical constraints. Examining responses to ion imbalances may assist in the identification of genotypes tolerant to chemical constraints in sodic soils and improve productivity. We evaluated the performance of four wheat (Triticum aestivum. L) genotypes in solutions with five sodium adsorption ratios (SARs) ranging from 0 to 60. For all four genotypes, seedling emergence and shoot dry matter (DM) decreased significantly with increasing SAR. A significant positive correlation was observed between Ca concentration in roots, as well as both root and shoot DM for all genotypes. At SAR values &gt;20, a more tolerant genotype (EGA Gregory), had higher Ca concentrations in root tissues, while a more sensitive genotype (Baxter) exhibited Na-induced Ca deficiency. Thus, selection for genotypes that are able to accumulate Ca in roots in sodic conditions may be a useful trait for selecting genotypes tolerant of soils with high ESP values. However, for soils that restrict plant growth at ESP (SAR) values of 6-10%, it is likely that growth is restricted by physical constraints rather than by a Na-induced Ca deficiency.

The antiradical and antimicrobial activity of lignin and lignin-based films are both of great interest for applications such as food packaging additives. The polyphenol structure of lignin in addition to the presence of O-containing functional groups is potentially responsible for these activities. This study used DPPH assays to discuss the antiradical activity of HPMC/lignin and HPMC/lignin/chitosan films. The scavenging activity (SA) of both binary (HPMC/lignin) and ternary (HPMC/lignin/chitosan) systems was affected by the percentage of the added lignin: the 5% addition showed the highest activity and the 30% addition had the lowest. Both, scavenging activity and antimicrobial activity are depending on the biomass source showing the following trend: organosolv of softwood > Kraft of softwood > organosolv of grass. Testing the antimicrobial activities of lignins and lignin-containing films showed high antimicrobial activities against gram-positive and gram-negative bacteria at 35 °C and at low temperatures (0-7 °C). Purification of kraft lignin has a negative effect on the antimicrobial activity while storage has positive effect. The lignin release in the produced films affected the activity positively and the chitosan addition enhances the activity even more for both gram-positive and gram-negative bacteria. Testing the films against spoilage bacteria that grow at low temperatures revealed the activity of the 30% addition on HPMC/L1 film against both B. thermosphacta and P. fluorescens while L5 was active only against B. thermosphacta. In HPMC/lignin/chitosan films the 5% addition exhibited activity against both B. thermosphacta and P. fluorescens.

The fishmeal production industry is essential for providing protein for animal feed in the aquaculture sector. However, the industry faces challenges related to energy consumption and environmental sustainability. This study evaluates the energy efficiency and environmental benefits of waste heat recovery (WHR) technologies in a fishmeal production plant in Vietnam. Data were collected from the plant between 2016 and 2022, and a specific energy consumption (SEC) indicator and a comprehensive methodology were utilized. Implementing an economizer as a WHR technology resulted in a 55.5% decrease in SEC compared to the state before installation. The enhanced energy efficiency also translated to reduced energy consumption per output unit. Moreover, the economizer contributed to annual energy savings of 4,537.57 GJ/year and cost savings of $26,474.49. Additionally, carbon dioxide (CO2) emissions associated with producing one ton of fishmeal decreased by 58.37%. These findings highlight the potential for WHR technologies to improve energy efficiency and reduce the environmental footprint of fishmeal production. The study's results provide valuable insights for practitioners and policymakers in promoting energy efficiency practices and reducing environmental impact in the industry.

In April 2019, a team of Keio University and Bucknell University students was assembled to participate in Ericsson Innovation Awards with a novel concept for generating renewable energy. This conceptual system consists of a vertical axis wind turbine, a crossflow marine hydrokinetic turbine, a floating platform integrated with a quadcopter system, and three to four temporary mooring lines with ship-type anchors. The proposed designed aims to offer solutions to two current problems of floating offshore wind energy: high construction cost of floating platforms and difficulties in maintenance of mooring lines. The combination of two vertical-axis turbines into a single floating platform would enable the system, namely ESwift, to extract energy from both wind and current resources. Additionally, due to the utilization of vertical axis turbines, the center of gravity of the proposed concept is significantly lower with respect to water level, compared to that of existing floating horizontal axis wind turbines, which would potentially reduce the floater's size and construction cost. Lastly, the integrated quadcopter mechanism would assist the floater in terms of stability and mobility, and enables an array of ESwifts to automatically rearrange for maximal energy generation. The authors hope that readers would find the idea described in this open access letter worth pursuing and would further develop and commercialize the ESwift concept.

Introduction: The goals of this retrospective cohort study of 129,443 persons admitted to Calgary acute care hospitals 2013-2021 were to ascertain correlations of “potentially inappropriate medi-cations” (PIMs), “potential prescribing omissions” (PPOs) and other risk factors with readmissions and mortality. Methods: Processing and analysis codes were built in Oracle Database 19c (PL/SQL), R and Excel. Results: The percentage dying during their hospital stay rose from 3.03% during the first to 7.2% during the 6th admission. The percentage dying within 6 months of discharge rose from 9.4% after the first to 24.9 after the sixth admission. Odds ratios (adjusted for age, gender and comorbidities) for readmission were the post-admission number of medications (1.16; 1.12-1.12), STOPP PIMs (1.16; 1.15-1.16); AGS Beers PIMs (1.11; 1.11-1.11) and START omissions not corrected with a prescription (1.39 (1.35-1.42). Odds ratios for mortality were post-admission number of medications (1.04; 1.04-1.05), STOPP PIMs (0.99; 0.96-1.00); AGS Beers PIMs (1.08; 1.07-1.08) and START omissions not corrected with a prescription (1.56 (1.50-1.63). START omissions corrected with a prescription correlated with a dramatic reduction in mortality (0.51; 0.49-0.53). Odds ratios for readmissions for the second through 39th admission were consistently higher if START PPOs were not corrected for the second admission (1.41; 1.36-1.46), third (1.41;1.35-1.48); fourth 1.35;1.28-1.44); fifth 1.38; 1.28-1.49); sixth (1.47;1.34-1.62) and 7th through 39th admission (1.23; 1.14-1.34). For all admissions when a pre-scription was given to correct START PPOs ORs for mortality within six months of discharge were dramatically improved (0.51; 0.49-0.53). This was also true for the second (0.52; 0.50-0.55; fourth (0.56; 0.52-0.61; fifth (0.63; 0.57-0.68); sixth (0.68; 0.61-0.76); and 7th through 39th admissions (0.71; 0.65-0.78). Conclusions: PPOs should be corrected by prescriptions and teams of family physicians, pharmacists and nurses should focus on patients’ understanding of their illnesses, medications and ability for self-care.

SARS-CoV2 (corona virus) has spread globally at an unprecedented rate; so far, increasing SARS-CoV2-infected individuals have been identified. Although the situation in China is improving and is currently under control, the outbreak in other countries and its pandemic management is only beginning to develop. Based on 154 SARS-CoV2 genome sequence analyses, we used receptor–ligand docking to identify one potential point mutation (V354F) on the spike structure which enhances spike binding to ACE2 receptors underlying potential super infection. Importantly, the V354F site on spike S1 had been identified in 5/10 infected French patients living in Paris, who sharing 100% identical SARS-CoV2 genomes. With Covid-19 cases increasing rapidly in France that could lead to a new explosion, we suggest that the French government should identify all potential super spreaders and treat them accordingly. In summary, our study provides on of the measures to avoid the potential second worldwide explosion of SARS-CoV2.

Electrical impedance tomography (EIT) can monitor the real-time hemodynamic state of a conscious and spontaneously breathing patient noninvasively. However, cardiac volume signal (CVS) extracted from EIT images has a small amplitude and is sensitive to motion artifacts (MAs). This study aimed to develop a new algorithm to reduce MAs from the CVS for more accurate heart rate (HR) and cardiac output (CO) monitoring in patients undergoing hemodialysis based on the source consistency between the electrocardiogram (ECG) and the CVS of heartbeats. Two signals were measured at different locations on the body through independent instruments and electrodes, but the frequency and phase were matched when no MAs. As the number of motions per hour (MI) increased over 30, the proposed algorithm had a correlation of 0.83 and a precision of 1.65 beats per minute (BPM) compared to the conventional statical algorithm of a correlation of 0.56 and a precision of 4.04 BPM. For CO monitoring, the precision and upper limit of the mean ∆CO were 3.41 and 2.82 liters per minute (LPM), respectively, compared to 4.05 and 3.82 LPM of the statistical algorithm. The developed algorithm could reduce MAs and improve HR/CO monitoring accuracy and reliability, particularly in high-motion environments.

The secretory pathway Ca2+-ATPase SPCA2 is a tumor suppressor in triple receptor negative breast cancer (TNBC), a highly aggressive molecular subtype that lacks tailored treatment options. Low expression of SPCA2 in TNBC confers poor survival prognosis in patients. Previous work has established that re-introducing SPCA2 to TNBC cells restores basal Ca2+ signaling, represses mesenchymal gene expression, mitigates tumor migration in vitro and metastasis in vivo. In this study, we examined the effect of histone deacetylase inhibitors (HDACi) in TNBC cell lines. We show that the pan-HDACi vorinostat and the class I HDACi romidepsin induce dose-dependent upregulation of SPCA2 transcript with concurrent downregulation of mesenchymal markers and tumor cell migration characteristic of epithelial phenotype. Silencing SPCA2 abolished the ability of HDACi to reverse epithelial to mesenchymal transition (EMT). Independent of ATPase activity, SPCA2 elevated resting Ca2+ levels to activate downstream components of non-canonical Wnt/Ca2+ signaling. HDACi treatment led to SPCA2-dependent phosphorylation of CAMKII and -catenin, turning Wnt signaling off. We conclude that SPCA2 mediates the efficacy of HDACi in reversing EMT in TNBC by a novel mode of non-canonical Wnt/Ca2+ signaling. Our findings provide incentive for screening epigenetic modulators that exploit Ca2+ signaling pathways to reverse EMT in breast tumors.

Neuroinflammatory responses are implicated in the pathogenesis of neurodegenerative diseases. In neurodegenerative diseases, neuroinflammatory reactions to neuronal injury are modulated by microglial cells, which are vital innate immune cells in the central nervous system. Activated microglial cells release proinflammatory cytokines, mediators, and neurotoxic factors that induce fatal neuronal injury. The present study investigated the anti-neuroinflammatory effects of cudratricusxanthone L (1), which was isolated from Cudrania tricuspidata. This compound reduced the levels of lipopolysaccharide-stimulated inflammatory mediators and cytokines, including nitric oxide, prostaglandin E2, interleukin (IL)-1β, tumor necrosis factor-α, IL-6, and IL-12. These effects suggested that cudratricusxanthone L (1) suppressed the nuclear factor-kappa B (NF-κB) signaling pathway. Specifically, cudratricusxanthone L (1) also attenuated the phosphorylation of Jun kinase and inhibited p38 mitogen-activated protein kinase (MAPK) signaling in BV2 and rat primary microglial cells. These results indicated that cudratricusxanthone L (1) effectively repressed neuroinflammatory processes in BV2 and rat primary microglial cells by inhibiting NF-κB and the MAPK signaling pathway.

In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

In this article, we present the use of the coupled land surface model and groundwater flow model SWAT-MODFLOW with the decision support tool WEAP (Water Evaluation and Planning software) to predict future surface water abstraction scenarios in a complex river basin, under conditions of climate change. The modeling framework is applied to the Dee River catchment in Wales, United Kingdom. Regarding hydrology, the coupled model improves overall water balance and low streamflow conditions, compared to a stand-alone SWAT model. The calibrated SWAT-MODFLOW is employed with high resolution climate model data from the UKCP18 project with future scenario of RCP85 from 2020 to 2040. Then, water supply results from SWAT-MODFLOW are fed into WEAP as input for the river reach in the downstream region of the river basin. This system is utilized to create various future scenarios of surface water abstraction of public water supply in the downstream region: maximum licensed withdraw, 50 % authorized abstractions, monthly time series with 1% increase of water use, and maximum water withdraw year based on historical records repeated every year with 1% increase of water use, to estimate the unmet demands and streamflow requirement. This modeling approach can be used in other river basins to manage scenarios of supply and demand.

Robotic path planning is a field of research which is gaining traction given the broad domains of interest to which path planning is an important systemic requirement; the aim being to optimise the efficacy of robotic movements in a defined operational environment. For example, robots have been employed in many domains including: cleaning robots (such as vacuum cleaners), automated paint spraying robots, window cleaning robots, forest monitoring robots, agricultural robots (often driven using satellite and geostationary positional satellite data). Additionally, mobile robotic systems have been utilised in disaster areas and locations hazardous to humans (such as war zones in mine clearance). The coverage path planning problem describes an approach which is designed to determine the path that traverses all points in a defined operational environment while avoiding static and dynamic (moving) obstacles. In this paper we present our proposed Smooth-STC model, the aim of the model being to identify an optimal path, avoid all obstacles, prevent (or at least minimise) backtracking, and maximise the coverage in any defined operational environment. The experimental results in a simulation show that, in uncertain environments, our proposed smooth STC method achieves an almost absolute coverage rate and demonstrates improvement when measured against alternative conventional algorithms.

Current instrumental technology in evaluating performance of skin care creams is still rather limited and there are no industrial standard testing equipment, method and performance specifications for it. In this paper, we report our attempt in using an instrument called PhabrOmeter for this purpose. PhabrOmeter is a commercialized instrument for sensory performance evaluation of textiles, leather, paper and nonwoven and has been designated by American Association of Textile Chemists and Colorists (AATCC) as a standard test method for textiles, AATCC TM 202 in 2013. By adopting artificial skin samples treated with skin care creams, we have developed a procedure to apply this instrument for evaluation of skin care creams from sample preparation, measurement to data analysis and interpretation. The results using commercial skin care creams to demonstrate the feasibility and advantages of this instrument are provided.