In the field of delta-sigma modulators, reducing system power consumption without sacrificing accuracy has become a challenge. The summing circuit, as the main part of the cascade-of-integrator-in-feedforward delta-sigma modulator, consumes a significant amount of power in active summing. On the other hand, passive summing circuits have low power consumption but can cause attenuation in the summing results. This article proposes a low-power multi-bit delta-sigma modulator based on passive and attenuationless summation scheme. The summation circuit achieves multiplication of the voltage signal carried on the summation capacitor through bidirectional sampling technique, compensating for the inherent attenuation caused by passive summation, thus eliminating the need for active OTA to achieve perfect summation. A 2-order delta-sigma modulator based on 4-bit 1-order passive noise-shaping (NS) SAR quantizer is designed to verify the scheme. By combining a passive NS SAR as the 4-bit quantizer and the third-stage integrator of the system, and incorporating an energy-efficient cascode floating inverter amplifier (FIA) structure as the core active OTA, these elements have significantly enhanced the energy-efficiency of the modulator. Simulation results show that at a supply voltage of 1.2 V and a bandwidth of 20 kHz, the SNDR reaches 102.62 dB, power consumption is only 148.32 μW, and Schreier figure-of-merit (FoM) of SNDR is 183.92 dB.

A novel five-surface phosphor-in-ceramic (FS-PiC) for high illumination and excellent color uniformity in larger-scale LEDs for sensor light source application is demonstrated. YAG phosphor (Y3Al5O12:Ce3+) was uniformly mixed with ceramic and sintered at 680°C to form a phosphor wafer. A sophisticated laser engraving was employed on the phosphor wafer to form a saddle-shaped large-scale FS-PiC LEDs. The performance of the FS-PiC LEDs exhibited the illumination of 401lm, average color temperature (CCT) of 5488K±110K, and color coordinates (CIE) of (0.3179±0.003, 0.3352±0.003). In contrast to convention single-surface phosphor-in-ceramic (SS-PiC) LEDs, the performance exhibited the illumination of 380lm, average CCT of 5830K±758K, and CIE of (0.3083±0.07, 0.3172±0.07). These indicated that the performance of the FS-PiC LEDs was higher than the SS-PiC LEDs for illumination, CCT, and CIE of 1.1, 7, and 23 times, respectively. Furthermore, the FS-PiC LEDs demonstrate lower lumen loss of 2% and less chromaticity shift of 5.4x10-3 under accelerated aging at 350°C for 1008 hours, owing to the high ceramic melting temperature of up to 510°C. In this study, the proposed FS-PiC larger-scale LEDs having excellent optical performance and high reliability may be the promising candidates to replace the convention phosphor-in-organic silicone material used in high-power LEDs for the next generation of sensor light sources, display, and headlight applications.

With the development of remote sensing satellite technology for Earth observation, remote sensing stereo images have been used for three-dimensional reconstruction in various fields, such as urban planning and construction. However, remote sensing images often include noise, occluded regions, weakly textured areas and repeated textures, which can lead to reduced accuracy in stereo matching and affect the quality of the 3D reconstruction results. To reduce the impact of complex scenes in remote sensing images on stereo matching and to ensure both speed and accuracy, we propose a new end-to-end stereo matching network based on convolutional neural networks (CNNs). The proposed stereo matching network can learn features at different scales from the original images and construct cost volumes with varying scales to obtain richer scale information. Additionally, when constructing the cost volume, we introduce negative disparity to adapt to the common occurrence of both negative and nonnegative disparities in remote sensing stereo image pairs. For cost aggregation, we employ a 3D convolution-based encoder-decoder structure that allows the network to adaptively aggregate information. Before feature aggregation, we also introduce an attention module to retain more valuable feature information, enhance feature representation, and obtain a higher-quality disparity map. By training on the publicly available US3D dataset, we obtain the accuracy that 1.115 pixel in end-point error (EPE) and 5.32% in the error pixel ratio (D1) on the test dataset, and the inference speed is 92 ms. Comparing our model with existing state-of-the-art models, we achieve higher accuracy, and the network is beneficial for the three-dimensional reconstruction of remote sensing images.

In a global context, the story of the Jesuit compound in Shanghai, since its establishment by French Jesuits in 1847, reflected not only conflicts between rival powers in Europe but also the fight for their interests in the Eastern world. The Pope, who was stuck without legal status in the Vatican after 1861, was also seeking the chance to save the authority of the Church in the face of questions regarding the extent of his temporal power and the status of Rome in the context of Italian unification. As in the Reformation, a break-through in the east seemed to offer a solution for losses in Europe. However, the Jesuits to the East in the late 19th century were not only troops working and fighting on behalf of the Pope; their identities under the French Protectorate added complexity to an already complicated story involving not just the Church, but the course of world history.The female Catholic orders at the east bank of Zi-ka-wei compound became a unique window to approach the complexity.

Emergence of zoonotic-human pathogens is proven to be a lethal threat to public health, and RNA virus including influenza viruses, severe acute respiratory syndrome coronavirus, middle east respiratory syndrome coronavirus, Wuhan coronavirus (COVID-19), plays a pivotal role. As those viruses as airborne microorganisms spread mainly by tiny airborne particles, it is important to de-active those airborne particles before their entry into human bodies. In this study, we investigated the effect of far infrared (FIR) radiation on inhibition of airborne microorganisms. The result confirmed that double stand DNA from airborne microorganisms were stable under mild FIR radiation. However, single strand RNA from them was found to be sensitive to FIR radiation, indicating that RNA virus in airborne particles is instable under FIR radiation. Based on this observation, two models on usage of FIR radiation to prevent RNA virus transmission and cure RNA virus infection were proposed, implying that FIR radiation might be a cheap, convenient, and efficient method in clinic to treat RNA virus.

An automated discharge imaging system (ADIS), a non-intrusive and safe approach, was developed for measuring river flows during flash flood events. ADIS consists of dual cameras to capture complete surface images in the near and far fields. Surface velocities are accurately measured using the Large Scale Particle Image Velocimetry (LSPIV) technique. The stream discharges are then obtained from the depth-averaged velocity (based upon an empirical velocity-index relationship) and cross-section area. The ADIS was deployed at the Yu-Feng gauging station in Shimen Reservoir upper catchment, northern Taiwan. For a rigorous validation, surface velocity measurements were conducted using ADIS/LSPIV and other instruments. In terms of the averaged surface velocity, all measured results were in good agreement with small differences, i.e., 0.004 to 0.39 m/s and 0.023 to 0.345 m/s when compared to those from acoustic Doppler current profiler (ADCP) and surface velocity radar (SVR), respectively. The ADIS/LSPIV was further applied to measure surface velocities and discharges during typhoon events (i.e., Chan-Hom, Soudelor, Goni, and Dujuan) in 2015. The measured water level and surface velocity both showed rapid increases due to flash floods. The estimated discharges from ADIS/LSPIV and ADCP were compared, presenting good consistency with correlation coefficient R = 0.996 and normalized root mean square error NRMSE = 7.96%. The results of sensitivity analysis indicate that components till (τ) and roll (θ) of the camera are most sensitive parameter to affect the surface velocity using ADIS/LSPIV. Overall, the ADIS based upon LSPIV technique effectively measures surface velocities for reliable estimations of river discharges during typhoon events.

Underwater target detection is widely used in various applications such as underwater search and rescue, underwater environment monitoring, and Marine resources survey. However, the visibility of the underwater environment and the accuracy of target detection can be affected by complex underwater light changes and unpredictable background noise. To address these issues, we propose an improved underwater target detection algorithm based on YOLOv8n. Our algorithm focuses on three aspects. Firstly, we replace the original C2f module with Deformable Convnets v2 to enhance the adaptive ability of the target region in the convolution check feature map and extract the target region's features more accurately. Secondly, we introduce SimAm, a non-parametric attention mechanism, which can deduce and assign three-dimensional attention weights without adding network parameters. Lastly, we optimize the loss function by replacing the CIOU loss function with the Wise-IOU loss function. To conduct our experiments, we create our own dataset of underwater target detection for experimentation. Meanwhile, we also utilized the Pascal VOC dataset to evaluate our approach. The [email protected] and [email protected]:0.95 of the original YOLOv8n algorithm on the underwater target detection were 88.6% and 51.8%, respectively, and the improved algorithm [email protected] and [email protected]:0.95 can reach 91.8% and 55.9%. The original YOLOV8n algorithm was 62.2% and 45.9% [email protected] and [email protected]:0.95 on the Pascal VOC dataset, respectively. The improved YOLOV8n algorithm [email protected] and [email protected]:0.95 were 65.7% and 48.3%, respectively. The floating-point computation volume of the model is reduced by about 6%. The above experimental results prove the effectiveness of our method.

Herein, the mechanical properties and carbonation durability of engineered cementitious composites (ECC) were studied. For cost-efficient utilization of ECC materials, polypropylene (PP) and hydrophilic polyvinyl alcohol (PVA) fibers were employed to cast different types of specimens. The compressive strength, Poisson’s ratio, strength-deflection curves, cracking/post-cracking strength, impact index, and tensile strain-stress curves of the two types of ECC materials, with different fiber contents of 0 vol%, 1 vol%, 1.5 vol% and 2 vol%, were investigated by conducting compressive tests, four-point bending tests, drop weight tests, and uniaxial tensile tests. In addition, the matrix microstructure and failure morphology of the fiber in the ECC materials were studied by scanning electron microscopy (SEM) analysis. Furthermore, carbonation test and steel corrosion after carbonization were employed to study durability resistance. The results indicated that for both PP fiber- and hydrophilic PVA fiber-reinforced ECCs, the compressive strength first increases and then decreases as fiber content increases from 0 vol% to 2 vol% and reaches the maximum at 1 vol% fiber content. The bending strength, deformation capacity, and impact resistance show significant improvement with increasing fiber contents. The ECC material reinforced with 2 vol% PP fiber shows superior carbonized durability with maximum carbonation depth of only 0.8 mm.

Epoxy asphalt (EA) concrete is widely used in constructing long-span steel bridge pavements (SBDPs). This study aims to derive a fatigue damage evolution law, conducting an experimental investigation of SBDP. First, a general theoretical form of the fatigue damage evolution law of materials is established based on the thermal motion of atoms. Then, fatigue experiments demonstrate that this evolution law well represents the known damage–life relationships of SBDP. Taking into account the experimental relationships between damage and fatigue life under symmetrical cyclic loadings with different overload amplitudes and temperature variations, a detailed damage evolution law is deduced. Finally, the role of damage accumulation is discussed on the basis of the proposed damage evolution law for the extreme situation of heavy overload and severe environments. The results show that both heavy loading and falling temperatures increase the fatigue damage of SBDP considerably; therefore, SBDP should avoid heavy loading combined with winter temperatures. EA shows a fatigue life two to three times longer than that of modified matrix asphalt (SMA) or guss asphalt (GA). For the same thickness, EA pavement is demonstrated to be more suitable for an anti-fatigue design of large-span SBDP under high traffic flows and low temperatures.

The modern material design aims to achieve multifunctionality by integrating structures in a diverse range, resulting in simple materials with embedded functions. Biological materials and organisms are typical examples of this concept, where complex functionalities are achieved through a limited material base. This review highlights the inspiration from multifunctional organisms and materials in nature, emphasizing their structural and functional integration. In particular, we discuss complex hierarchical architectures ranging from the nanoscale to the macroscale, to achieve multifunctional properties such as extreme pressure, impact and wear resistance, shape memory and self-healing, adhesiveness and anti-fouling, sensing-actuating and sensing-camouflage, and extreme environmental survival. These strategies of integrating structure and function are critical for promoting innovations and breakthroughs in the modern engineering materials and applications.

There have been several cases of large-scale wind generators (WGs) tripping off caused by untimely fault removing in recent years. Currently, the discoordination between the box-type transformer fuse protection (BTFP) and two-section collecting line current protection (CLCP) brings a security risk to wind farm. In order to ensure the selectivity, the first section (Sec-I) CLCP should be set a enough interval that is longer than the fuse melting time, and another interval is set for the Sec-II CLCP, which weakens the speed of the CLCP. When a fault occurs on the collecting line, there is no doubt that WGs cannot work too long in abnormal operation, which may cause WGs to be placed off the grid. For a power system with high penetration of wind power, large-scale WGs tripping off will cause a great power shortage, and affect the stability of the power system. The selectivity and sensitivity of the CLCP is analyzed in detail to make the CLCP speed better. Considering the fault ride-through ability of WGs, the fault clear time is an important factor to lead to large-scale WGs tripping off. Two main works are done in this paper. The first is to accelerate the speed of the Sec-I CLCP though reducing the protection zone. Another one is introduce the risk assessment module into the CLCP, which not only improve the speed of the CLCP but also ensure the safety of the wind farm during faults. According to the deference in trip-off causes of WGs, the matching functions are created to assess the trip-off risk of WGs on the spot. In the case of fault, the trip-off risk indicators of WGs are timely updated to data sharing center and open to the CLCPs. The set of risk indicators is divided into several subsets according to the risk range. The dynamic changes of the subsets during fault help to improved CLCP scheme. This scheme can accelerate protection speed based on the increasing risk of large-scale WGs tripping off in wind farms. Compared with traditional CLCP, this approach can make the CLCP combines selectivity and speed better based on the analysis of the ride- through ability of WGs.

A new longitudinal flow heat dissipation theory for cylindrical batteries is proposed in order to increase the energy density and uniform temperature performance of cylindrical lithium-ion battery packs while also shrinking their size by roughly 10%. First, a genetic algorithm is used to identify the single cell's thermal properties. Based on this, modeling and simulation are used to examine the thermal properties of the longitudinal flow-cooled battery pack. It is found that the best coolant flow scheme has one inlet and one outlet from the end face, taking into account the cooling effect of the battery pack and engineering viability. Lastly, Thermal Dummy Cells (TDC) is used to conduct a validation test of the liquid cooling strategy. Additionally, the simulation and test results demonstrated that the liquid cooling solution can keep the battery pack's maximum temperature rise under the static conditions of a continuous, high-current discharge at a rate of 3C to 20 °C and under the dynamic conditions of the New European Driving Cycle (NEDC) to 2 °C. In applications where the space requirements for the battery pack are quite severe, the longitudinal flow cooling method has some advantages.

Bionic robotic hand can perform many movements similar to human hand. But there is still a significant gap in manipulation between robot and human hand. It is necessary to understand the finger kinematics and motion patterns of human hand to improve the performance of robotic hand. This study aimed to comprehensively investigate normal hand motion patterns by evaluating the kinematics of hand grip and release in healthy individuals. The data corresponding to rapid grip and release were collected from the dominant hand of 22 healthy people by sensory glove. The kinematics of 14 finger joints were analyzed, including the dynamic range of motion (ROM), peak velocity, joint sequence and finger sequence. The results show that the proximal interphalangeal (PIP) joint had a largest dynamic ROM than metacarpophalangeal (MCP) and distal interphalangeal (DIP) joints. Besides, the PIP joint had the highest peak velocity, both in flexion and extension. For joint sequence, the PIP joint moved prior to the DIP or MCP joints during flexion, while extension started in DIP or MCP joints, followed by PIP joint. Regarding the finger sequence, the thumb started to move before four fingers, and stopped moving after the fingers during both grip and release. This study explored the normal motion patterns in hand grip and release, which provided kinematic reference for the design of robotic hand and thus contribute to its development.

In the world city theory, most researchers focus on the service sector in the urban economy and less discuss the role of manufacturing. However, the path of only emphasizing financial and corporate service could not fit the sustainability concept. Compared to Anglo-American world city, Global South’s world cities have distinct pathway to be industrialization, tertiarization and globalization. This paper adopted dynamic historic perspective with first-hand materials including in-depth interviews with managers and government officers and second-hand data including yearbook statics and economic census to closely examine the emerging world city-- ‘World Factory’ in Global South, Guangzhou in China, from 1949 to 2015, to emphasize how manufacturing affects the urban globalization through three dimensions, economic, social and spatial dimensions. To make the confirmation of the role of manufacturing in Guangzhou as sustainable world city, we find manufacturing in Guangzhou builds up the basic foundation of export-oriented economy and makes positive effects on urban economic transformation. In addition, manufacturing remains important source of employment and foreign immigration. Along with urbanization and industrialization, urban spatial expansion and aggregation changes with different urban development concept. We provide new insights on multiple globalization on manufacturing for sustainable world city.

Background: Strengthening adherence to self-care behaviors in patients with periodontal disease (PD) and reducing plaque index is crucial for improving PD treatment. We evaluated the effectiveness of a theory of planned behavior (TPB)-based health education intervention involving planning strategy on self-care behaviors in patients with PD. Methods: A randomized controlled trial was conducted; 158 and 139 patients comprised the experimental group (EG) and control group (CG), respectively. Both groups received a leaflet, and the EG also received a planning intervention, which was a brief one-on-one counseling session with a planning sheet. Data were collected using a self-administered questionnaire. Results: Between-group comparisons of TPB measures revealed significant differences in all domains when controlling for baseline covariates. The EG exhibited significantly higher levels of action and coping planning than the CG at 2-week follow-up (effect size (ES) = 5.54 and 5.57, respectively) and 6-week follow-up (ES = 5.66 and 5.66, respectively). Between-group differences in changes of brushing behaviors increased significantly. More frequent use of dental floss was observed in the EG than in the CG at 2-week and 6-week follow-ups (24.7% and 22.8%, respectively). Conclusions: The intervention involving planning strategy effectively promoted adherence to self-care behaviors in patients with PD.

The International Maritime Organization (IMO) has recently revised its strategy for shipping de-carbonization, deepening the ambition to reduce annual greenhouse gas emissions until 2050. The accomplishment of this strategy requires the large-scale deployment of alternative maritime fuels, whose diversity and technical characteristics impose transition challenges. While several studies address the production of these fuels, a notable gap lies in the analysis of the required adaptations in vessels and ports for their usage. This study aims to fill this gap through a comprehensive re-view of material compatibility, storage in ports/vessels, and bunkering technology. Firstly, we an-alyze key aspects of port/vessel adaptation: physical and chemical properties; energy conversion for propulsion; fuel feeding and storage; bunkering procedures. Then, we perform a maturity as-sessment, placing each studied fuel on the technological readiness scale, revealing the most prom-ising options regarding infrastructure adaptability. Finally, we develop a case study for Brazil, whose economy is grounded on maritime exports. Findings indicate that multi-product ports may have potential to serve as multi-fuel hubs, while the remaining ports are inclined to specific fuels. In terms of vessel categories, we find that oil tankers, chemical ships and gas carriers are the most ready for conversion in the short-term

A novel drive current model covering the effects of source/drain voltage (VDS) and gate voltage (VGS) and incorporating drift and diffusion current on the surface channel at the nano-node level, especially beyond 28nm node is presented. The effect of the diffusion current added is more satisfactory to describe the behavior of the drive current in nano-node MOSFETs, fabricated with the atomic-layer-deposition (ALD) technology. This breakthrough in model establishment can expose the long and short channel devices together. Introducing the variables of VDS and VGS, the mixed current model more effectively and meaningfully demonstrates the drive current of MOSFETs under the operation of horizontal, vertical, or mixed electrical field. In comparison between the simulation and experimental consequences, the electrical performance is impressive. The error between both is less than 1%, better than the empirical adjustment to issue a set of drive current models.

Initial water content significantly affects the efficiency of soil stabilization. In this study, the effects of initial water content on the compressibility, strength, microstructure and composition of a lean clay soil stabilized by compound calcium-based stabilizer were investigated by static compaction test, unconfined compression test, optical microscope observations, environment scanning electron microscopy, energy dispersive X-ray spectroscopy and X-ray diffraction spectroscopy. The results indicate that as the initial water content increases in the range studied, both the compaction energy and the maximum compaction force decrease linearly and there are less soil aggregates or agglomerations, and smaller proportion of large pores in the compacted mixture structure. In addition, for specimens cured with or without external water supply and under different compaction degrees, the variation law of the unconfined compressive strength with initial water content is different and the highest strength value is obtained at various initial water contents. With the increase of initial water content, the percentage of oxygen element tends to increase in the reaction products of the calcium-based stabilizer, whereas the crystalline mineral of the soil did not change obviously.

Background: The aim of this study was to investigate the risk of obstructive sleep apnea (OSA) among ankylosing spondylitis (AS) patients in a nationwide population. Methods: We conducted a nationwide cohort study between 2003 and 2013 using the Taiwan National Health Insurance Research Database. The AS cohort included 2210 patients who were newly diagnosed between 2003 and 2013. Randomly selected non-AS controls were matched at a 1:4 ratio based on age, sex and index date. The endpoint of OSA was occurrence or the end of 2013. Cumulative incidences, hazard ratios (HRs) and 95% confidence intervals (CIs) were calculated after adjusting for age, gender, comorbidities and co-medications. Multivariate analyses were performed using Cox proportional hazards model. Due to violation of the proportionality assumption, landmark analysis was conducted to explore the risk of OSA during specific follow-up periods. Results: The adjusted HR (aHR) of OSA for the AS group was 2.826 (95% C.I. = 1.727–4.625) compared to the control group. On landmark analysis, aHR was 7.919 (95% C.I. = 3.169–19.792) for AS group 0–24 months from index date, and decreased to 1.816 (95% C.I. = 0.944–3.494) at ≥ 24 months from index date. On subgroup analyses increased risks of OSA in AS group compared to the control group were found for both males and females (aHRs were 4.533 (95% C.I. = 1.441–14.262) and 2.672 (95% C.I. = 1.522–4.692) for females and males, respectively). On age stratified analysis, there was significant risk only for the 40–59 age group with aHR of 3.913 (95% C.I. = 1.890–8.102). Conclusions: A higher risk of developing OSA was found among newly diagnosed AS cohort during the 12-year follow-up period, especially within 2 years after AS index date and in the 40–59 age group.

This paper presents three types of tensor Conjugate-Gradient methods for solving large-scale linear discrete ill-posed problems based on the t-product between third-order tensors. An automatical determination strategy of a suitable regularization parameter is proposed for the tensor conjugate gradient (tCG) method. A truncated version and a preprocessed verion of the tCG method are further presented. The discrepancy principle is employed to determine a suitable regularization parameter. Several numerical examples are given to show the effectiveness of the proposed tCG methods in image and video restoration.

To evaluate the effect of middle meningeal artery embolization (MMAE) on chronic subdural hematoma (CSDH). We enrolled consecutive patients with CSDH who underwent burr hole craniostomy (BHC) between January 2021 and February 2023. The primary outcome was recurrence rate, defined as an increase of hematoma width on imaging compared with the immediate postoperative imaging at a 3-month follow-up. Secondary outcomes included the rate of complications and adverse prognosis. Cohorts were balanced using 1:2 propensity score matching (PSM). A total of 271 patients were eligible for this study and divided into the MMAE group (n=23) and the BHC group (n=205). Compared with the BHC group, there was more use of anticoagulant or antiplatelet medication (47.8% vs 22.4%, P=0.008), bilateral hematoma (19.5% vs 19.5%, P=0.043) and hematoma with septations (47.8% vs 21.5%, P=0.005) in the MMAE group. After PSM, 64 cases were finally successfully matched. The logistic analysis result showed that MMAE was associated with the decreased recurrence rate of CSDH in the cohort after PSM (OR 0.072, 95%CI 0.322~0.746, P=0.028) but not with the improved clinical prognosis (OR 0.065, 95%CI 0.533~4.786, P=0.562). MAAE has a positive therapeutic effect on reducing the recurrence rate of CSDHs as an adjunct postoperative treatment after burr hole surgery.

Precision and accuracy estimation is an important index used to reflect the measurement performance and quality of a measurement system. To reveal the significance and connotations of the precision and accuracy estimation index of a close-range photogrammetry system, several common precision and accuracy estimation methods used in close-range photogrammetry are explained from a theoretical perspective, and the mechanism of the internal coincidence precision estimation and the external coincidence accuracy estimation are deduced, respectively. Through detailed experimental design and testing, the validity and reliability of the proposed precision and accuracy estimation methods are verified, which provides strong evidence for the quality control, optimisation, and evaluation of the measurement results from a close-range photogrammetry system. At the same time, it has significance for the further development of precision and accuracy estimation analysis of close-range photogrammetry systems.

Vaccines trigger a complicated immunological response that includes B and T cells, with B cells producing antibodies. SARS-CoV-2 immunity weakens over time after vaccination. Discovering key changes in antigen-reactive antibodies over time after vaccination could help improve vaccine efficiency. In this study, we collected data on blood antibody levels in a cohort of healthcare workers vaccinated for COVID-19 and obtained 73 antigens in samples from four groups according to the duration after vaccination, including 104 unvaccinated healthcare workers, 534 healthcare workers within 60 days after vaccination, 594 healthcare workers between 60 and 180 days after vaccination, and 141 healthcare workers over 180 days after vaccination. An efficient machine learning based framework containing four feature selection methods (least absolute shrinkage and selection operator, light gradient boosting machine, Monte Carlo feature selection, and maximum relevance minimum redundancy) and four classification algorithms (decision tree, k-nearest neighbor, random forest, and support vector machine) was designed to screen out essential antigens. Several efficient classifiers with weighted F1 value around 0.75 were constructed. This study revealed that S1+S2, S1.mFcTag, S1.HisTag, S1, S2, Spike.RBD.His.Bac, Spike.RBD.rFc, and S1.RBD.mFc were most highly ranked among all features, where S1 and S2 are the subunits of Spike, and the suffixes represent the tagging information of different recombinant proteins. Meanwhile, the classification rules were extracted from the optimal decision tree to explain quantitatively the roles of antigens in the classification. This study identified antibodies associated with decreased clinical immunity based on populations with different time spans after vaccination. These antibodies have important implications for maintaining long-term immunity to SARS-CoV-2.

Shallow landslides pose serious threats to human existence and economic development, especially in the Himalayan areas. Landslide susceptibility mapping (LSM) is a proven way for minimizing the hazard and risk of landslides. Modeling as an essential step, various algorithms have been applied to LSM. In this study, information value (IV) and logistic regression (LR) were selected as representatives of the conventional algorithms, categorical boosting (CatBoost) and conventional neural networks (CNN) as the advanced algorithms, for LSM in Yadong county, and their performance was compared. To begin with, 496 historical landslide events were compiled into a landslide inventory map, followed by a list of 11 conditioning factors, forming a data set. Secondly, the data set was randomly divided into two parts, 80% of which was used for modeling and 20% for validation. Finally, the area under the curve (AUC) and statistical metrics were applied to validate and compare the performance of the models. The results showed that the CNN model performed the best (AUC 0.974 and accuracy=93.3%), while the LR model performed the worst (AUC 0.974 and accuracy=93.3%) and CatBoost model performed better (AUC 0.974 and accuracy=93.3%). Besides, the LSM constructed by the CNN model did a more reasonable prediction of the distribution of susceptible areas. As for feature selection, did a more detailed analysis of conditioning factors but the results were uncertain. The result analyzed by GI may be more reliable but fluctuates with the amount of data. The conclusion reveals that the accuracy of LSM can be further improved with the advancement of algorithms, by determining more representative features, which serve as a more effective guide for land use planning in the study area or other highlands where landslides are frequent.

Ischemic neuron loss contributes to brain dysfunction in patients with cardiac arrest (CA). Histidine–tryptophan–ketoglutarate (HTK) solution is a preservative used during organ transplantation. Can HTK also protect neurons from severe hypoxia (SH) following CA? We isolated rat primary cortical neurons and induced SH with or without HTK. Changes in caspase-3, hypoxia-inducible factor 1-alpha (HIF-1α), and NADPH oxidase-4 (NOX4) expression were evaluated at different time points till 72 h. Using a rat asphyxia model, we induced CA-mediated brain damage and then completed resuscitation. HTK or sterile saline was administered into the left carotid artery. Neurological deficit scoring and mortality were evaluated for 3 days. Then the rats were sacrificed for evaluating NOX4 and H2O2 level in blood and brain. In the in vitro study, HTK attenuated SH- and H2O2-mediated cytotoxicity in a volume- and time-dependent manner, associated with persisted HIF-1α expression, reductions in procaspase-3 activation and NOX4 expression. The inhibition of HIF-1α abrogated HTK’s effect on NOX4. In the in vivo study, neurological scores were significantly improved by HTK. H2O2 level, NOX4 activity and NOX4 gene expression were all decreased in the brain specimen of HTK-treated rats. Our results suggest that HTK acts as an effective neuroprotective solution.

Whether and how P2X7 receptor knockout (KO) modulates central post-stroke pain (CPSP) induced by lesions of the ventrobasal complex (VBC) of the thalamus regarding behavioral, molecular, and electrical recording parameters remains unclear. Following the experimental protocols of a rat hemorrhage CPSP model, the VBC of the thalamus of wild-type and P2X7 receptor KO mice was injected with 10 mU/0.2 μl type IV collagenase to produce an animal model of stroke-like thalamic hemorrhage. Behavioral data showed that the CPSP group induced thermal and mechanical pain, while the P2X7 receptor KO group showed reduced thermal and mechanical pain behaviors. Molecular assessments revealed that the CPSP group had lower expression of NeuN and KCC2 and higher expression of GFAP, IBA1, and BDNF. The P2X7 KO group showed lower expression of GFAP, IBA1, and BDNF and higher expression of KCC2 than the CPSP group. The expression of NKCC1, GABAa receptor, and TrkB did not differ significantly between the control, CPSP, and P2X7 receptor KO groups. Muscimol application increased multiunit numbers and [Cl-] influx in the membrane in the CPSP group, while P2X7 receptor KO reduced multiunit activity and [Cl-] outflux. P2X4 receptor expression was significantly decreased in the 100 kb but not the 50 kb site in the P2X7 receptor KO group. Altogether, the P2X7 hypothesis of CPSP was proposed, wherein P2X7 receptor KO changed the CPSP pain behavior, numbers of astrocytes and microglia, CSD amplitude of the anterior cingulate cortex and the medial dorsal thalamus, BDNF and KCC2 expression, [Cl-], and P2X4 activation in 100 kb with P2X7 receptors. The present findings have implications for the clinical treatment of CPSP symptoms.

In this paper, a voice coil motor (VCM) actuated fast tool servo (FTS) system is developed for diamond turning. To guide motions of the VCM actuator, a crossed double parallelogram flexure mechanism is selected featuring totally symmetric structure with high lateral stiffness. To facilitate the determination of the multi-physical parameters, analytical models of both electromagnetic and mechanical systems are developed. The designed FTS with balanced stroke and natural frequency is then verified through the finite element analysis. Finally, the prototype of the VCM actuated FTS is fabricated and experimentally demonstrated to have a stroke of ±59.02 μm and a first natural frequency of 253 Hz. By constructing a closed-loop control using PID controller with the internal-model based resonant controller, the error for tracking a harmonic trajectory with ±10 μm amplitude and 120 Hz frequency is obtained to be ±0.2 μm, demonstrating the capability of the FTS for high accuracy trajectory tracking.

The study comprehensively evaluated the prognostic roles of PLR, NLR, MLR, BLR, and ELR in patients with acute exacerbation chronic obstructive pulmonary disease (AECOPD). 619 patients with AECOPD and 300 healthy volunteers were retrospectively included into the study. The clinical characteristics containing laboratory findings of the AECOPD patients and the blood cell counts (CBCs) of the healthy volunteers were collected. Compared with the healthy volunteers, PLR, NLR, and MLR were elevated in COPD patients in stable condition, and were further ele-vated during exacerbation. ELR showed the opposite trend. PLR, NLR, and MLR were all posi-tively correlated with hospital LOS as well as CRP. In contrast, ELR was negatively correlated with hospital LOS as well as CRP. Elevated PLR, NLR, and MLR were all associated with more serious airflow limitation in AECOPD. Elevated PLR, NLR, and MLR were all associated with increased in-hospital mortality while Elevated ELR was associated with decreased in-hospital mortality in AECOPD. A nomogram was construct to predict in-hospital mortality in AECOPD. The nomo-gram had a C-index of 0.850 (95% CI: 0.799 – 0.901) with good predictive value and clinical ap-plicability. In summary, PLR, NLR, MLR, and ELR served as predictors for clinical outcomes in patients with AECOPD.

RNA interference (RNAi) is one of the main mechanisms for disease resistance and small RNA production in plants. The main proteins involved in RNAi include Dicer-like (DCL), RNA-dependent RNA polymerase (RDR), double-stranded RNA-binding (DRB), and Argonaute (AGO). Juglandaceae contains a variety of important woody plants, and walnuts are one of the four major woody plant groups and one of the four major dried fruits in the world. To clarify the evolution and functional differentiation of RNAi-related proteins in the walnut (Juglans regia) genome, this study integrated various web resources from gene family acquisition to structural analysis and transcriptome data to correlate walnuts and their congeners. The walnut genome has 5 DCL, 13 RDR, 15 DRB and 15 AGO genes, similar genes encoding conserved protein structural domains and conserved motifs with similar subcellular localization. Walnut AGO proteins are classified into three classes and seven subclasses. The DCL is divided into four categories, while RDR is mainly divided into four categories, and DRB can be divided into six categories. The exception is that the copy number of walnut RDR1 is 9, in which seven RDR1 are distributed in clusters on chromosome 16. Purifying selection drove the formation of walnut genes, but protein classes were subjected to varying degrees of purifying selection. Additionally, these results showed some similarity in other plants of the walnut family. Moreover, different RNAi-related genes of walnut produced abundant selective expression in response to different tissues and stresses. In this study, DCL, RDR, DRB and AGO gene families were identified and analysed in the genome of the walnut family for the first time and preliminarily examined the evolution, structure and expression characteristics of these families to provide a preliminary basis for the evolution of the walnut RNAi pathway and breeding research.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

In order to explore the grassland ecosystem productivity and landscape ecological patterns of main pastoral grasslands in China, it provides a theoretical basis for the efficient implementation of ecological engineering and rational management of grassland resources in the region. This study analyzed the changes in grassland area, landscape index (LSI), and net primary productivity (NPP) in seven major pastoral areas in China in 1985, 1995, 2005, and 2015. Results showed that (1) the sizes of the grassland study area in 1985, 1995, 2005, and 2015 were 248.34, 243.93, 245.80, and 244.660 km2 respectively. (2) The dominance of grassland in the landscape pattern increased from 2005 to 2015 as compared with that in 1985–1995 and 1995–2005. The degrees of spatial heterogeneity were reduced. (3) The grassland NPP showed spatial and temporal differences. The average NPP of grassland increased by 21.30%, 16.47%, and 36.17% during 1985–1995, 2005–2015, and 1985–2015, respectively. From 1995 to 2005, the average NPP decreased by 5.05 gC/m2, which is equivalent to -3.61% of the average NPP in 1995. The total amount of grassland NPP in the study area was the greatest in 2015, showing increments of 36.37% and 16.61% compared with those in 1985 and 2005, respectively.

CdZnTe (CZT) is a new type of compound semiconductor that has emerged in recent years. Compared to other semiconductor materials, it possesses an ideal bandgap, high density, and high electron mobility, rendering it an excellent room-temperature composite semiconductor material for X-ray and γ-ray detectors. Due to the exceptional performance of CZT material, detectors manufactured using it exhibit high energy resolution, spatial resolution, and detection efficiency. They also have the advantage of operating at room temperature. CZT array detectors, furthermore, demonstrate outstanding spatial detection and three-dimensional imaging capabilities. Researchers worldwide have conducted extensive studies on this subject. This paper, building upon this foundation, provides a comprehensive analysis of CZT crystals and CZT array detectors, summarizes existing research to offer valuable insights for envisioning new detector methodologies.

In the clock network design, the trade-off between power consumption and timing closure is an important and difficult issue. To achieve this target, a hybrid clock network architecture that combines both clock tree and clock mesh seems to be a promising solution. In this paper, we propose a novel clock mesh architecture – cross-mesh, with the average dispersion of the overall driving force, our methodology creates small non-zero skew clock trees. In addition, we integrate clock gating and register clustering techniques to further reduce dynamic power consumption. The proposed algorithms have four stages: cross-mesh planning, register clustering, mesh line connecting, and load balancing. Experimental results show that our methodology and algorithms get feasible solution effectively and improve both power consumption and clock skew simultaneously.

In this study, we used the natural and anthropogenic characteristics of a coastal region to generate risk maps showing vulnerability and potential hazards, and proposed design criteria for coastal defense and land use for the various kinds of risks faced. The Yunlin coast: a first-level protection area in mid-west Taiwan, was then used as an example to illustrate the proposed design criteria. The safety of the present coastal defenses and land use of the Yunlin coastal area was assessed, and coastal protection measures for hazard prevention were proposed based on the generated risk map. The results can be informative for future coastal management and the promotion of sustainable development of coastal zones.

Heavy metal contaminants have serious consequences for the environment and human health. Consequently, effective methods for detecting their presence, particularly in water and food, are urgently required. Accordingly, the present study proposes a sensor for the detection of mercury Hg(II) and lead Pb(II) ions using graphene oxide (GO) as a quenching agent and aptamer solu-tion as a reagent. In the proposed device, the aptamer sequences are labeled by FAM and HEX fluorescent dyes, respectively, and are mixed with 500 ppm GO solution in a microfluidic device. The presence of Hg(II) and Pb(II) ions is then detected by measuring the change in the fluores-cence intensity of the GO/aptamer suspension as the aptamer molecules undergo fluorescence resonance energy transfer (FRET). The experimental results show that the aptamer sensors have a linear range of 10~250 nM (i.e., 2.0~50 ppb) for Hg(II) ions and 10~100 nM (i.e., 2.1~20.7 ppb) for Pb(II) ions. Furthermore, the limit of detection is around 2 ppb for both metals, which is signifi-cantly lower than the maximum limits of 6 ppb and 10 ppb prescribed by the World Health Or-ganization (WHO) for Hg(II) and Pb(II) in drinking water, respectively.

Xinjiang, as a climate-sensitive region in northwest China, holds significant importance in studying extreme weather events for agricultural production and socioeconomic development. Based on data from 52 meteorological stations and 23 extreme climate indicators in Xinjiang from 1960 to 2021, the 5a moving average, linear trend estimation, climate tendency rate, and GIS spatial analysis methods are used to analyze the distribution and change characteristics of extreme climate. The results revealed that from 1960 to 2021, TXx, TNx, TXn, TNn, FD, ID, TN10p, TX10p, and WSDI showed a significant upward trend, while SU, TR, TN90p, TX90p, and CSDI showed a significant downward trend. What is more, the range of changes in the extreme temperature indexes from 1990 to 2021 is higher than that of 1960 to 1989. The high-value areas of extreme indexes are primarily concentrated in the northern part, while the high-value areas of cold event indexes are mainly distributed in the southern part. The upward/downward trends all accounting for over 80.00% of the entire region. The Rx1day, Rx5day, PRCPTOT, R95p, R99p, R10, R20, and R25 showed a significant growth trend from 1960 to 2021, and the range of change in the extreme precipitation indexes from 1990 to 2021 was lower than that from 1960 to 1989. Moreover, their high-value areas and high climate tendency areas are mainly concentrated in the northern and western parts of Xinjiang, with upward trends all accounting for over 71.00% of the entire region. The research results provide theoretical foundations for formulating climate risk strategies in the northwest region of China.

The rapid development of multicopters has led to many security problems. In order to prevent multicopters from invading restricted areas or famous buildings, an Anti-UAV Defense System (AUDS) has been developed and become a research topic of interest. Topics under research in relation to this include electromagnetic interference guns for unmanned aerial vehicles (UAVs), high-energy laser guns, US military net warheads, and AUDSs with net guns. However, these AUDSs use either manual aiming or expensive radar to track UAVs. This paper proposes a dual-axis rotary platform with UAV automatic tracking. The tracking platform uses visual image processing technology to track and lock the dynamic displacement of a UAV. When a target UAV is locked, the system uses a nine-axis attitude meter and laser rangefinders to measure its flight altitude and calculates its longitude and latitude coordinates through sphere coordinates to provide UAV monitoring for further defense or attack missions. Tracking tests of UAV flights in the air were carried out using a DJI MAVIC UAV at a height of 30 meters to 100 meters. It was set up for UAV image capture and visual recognition for tracking under various weather conditions by a thermal imager and a full-color camera respectively. When there was no cloud during the daytime, the images captured by the thermal imager and full-color camera provide a high-quality image recognition result. However, under dark weather, black clouds will emit radiant energy and seriously affect the capture of images by a thermal imager. When there is no cloud at night, the thermal imager performs well in UAV image capture. When the UAV is tracked and locked, the system can effectively obtain the flight altitude and longitude and latitude coordinate values.

The surface behavior of the ZnO-based films could be modulated via a postannealing and ultraviolet (UV) irradiation with different powers and time, respectively. These present results could provide modulate the microstructure related in grain-size distribution and photocatalytic behavior for potential guide in the field of wide bandgap semiconducting oxides. The ZnO films were prepared onto Corning-1737 glass substrates by using radio-frequency magnetron sputtering without supplying oxygen source at room temperature. For the purpose of obtaining modulable grain microstructures, the as-prepared ZnO films (Z0) were treated via a postannealing modification in vacuum furnace at 300°C for 30 minutes after deposition (Z300) accompanied with the adjustable internal stress. The contact angle (CA) value of ZnO film reduced from 95° to 68° was owning to the different grain microstructure accompanied by a change in size variation. In addition, the UV light with different irradiation powers could also be used to improve the hydrophilicity varied from hydrophobic status to superhydrophilic status due to the desirable surface characteristics of the photocatalytic action. In addition, the photocatalytic activity of ZnO film exhibited efficient photodegradation of methylene blue (MB) under UV irradiation, with a chemical reaction constant of 2.93×10-3 min−1. In this present work, we demonstrated that the CA value of the ZnO films not only caused from hydrophobic to hydrophilic status accompanied by a change in grain size combined with internal stress but also induced by the UV light irradiation combined with photocatalytic activity simultaneously. On the other hand, the enhanced surface plasmonic resonance could be observed that is due to couple electron and photon oscillations and can be generated at the interface between a flat, continuous Pt capping nanolayer. This designed structure could also be considered as a Pt electrode pattern onto ZnO (metal Pt/ ceramic ZnO) for multifunctional heterostructured sensors and devices in near future.

The origin and significance of the tonalite–trondhjemite–granodiorite (TTG) units and the familiar metabasite xenoliths they host in the Yangtze Craton, China, remain controversial, and resolving these issues is important if we are to understand the evolution of the early Yangtze Craton. We focused on biotite–tremolite schist xenoliths in the Archean TTG units of the Kongling high-grade metamorphic terrane, and U–Pb dating of their zircons yielded ²⁰⁷Pb/²⁰⁶Pb ages of ca. 3.00 Ga, which provides a minimum age for the formation of the pre-metamorphic basic igneous rock. The host TTGs and late intrusive granitic dikes yield three groups of upper intercept ages at 2.87–2.88, 2.91–2.94, and 3.07 Ga, and a concordant age at 2.94 Ga, which suggest that the Yangtze continental nucleus underwent three important metamorphic–magmatic events in the Mesoarchean at ca. 3.00, 2.94, and 2.87 Ga. The biotite–tremolite schists have high ratios of K₂O/Na₂O and high contents of CaO, Cr, and Ni, thus showing the characteristics of high-K calc-alkaline island-arc volcanic rocks (basalt–andesite) that form by the partial melting of subducted oceanic crust. The data also provide further proof that a Mesoarchean metamorphic basement exists in the Yangtze Plate. Derivation of the magmatic protoliths of the biotite–tremolite schist enclaves from an oceanic crust during slab subduction, and the presence of these xenoliths within the TTG suite, indicate the existence of the initiation of plate tectonics during the Mesoarchean (≤2.94 Ga).

Achieving effective control over microbial contamination necessitates the precise and concurrent identification of numerous pathogens. In this research, we have devised a remarkably sensitive duplex droplet digital PCR (dddPCR) reaction system to simultaneously detect Pseudomonas aeruginosa (P. aeruginosa) and Pseudomonas fragi (P. fragi). Employing comparative genomics, we identified four genes of P. fragi. By specific analysis, RS22680 gene was selected as the detection target of P. fragi and LasR gene was chosed as P. aeruginosa, which were applied to construct a dddPCR reaction. In terms of specificity, sensitivity and anti-interference ability, the constructed dddPCR detection system was verified and analyzed. The assay showed excellent sensitivity and applicability, as evidenced by a limit of detection of 100 CFU/mL. When the concentration of natural background bacteria in milk or fresh meat was 100 times that of the target detection bacteria, the method was still capable of completing the absolute quantification. In the simulation of actual sample contamination, P. aeruginosa could be detected after 3 h of enrichment culture, and P. fragi could be detected after 6 h. The established ddPCR detection system exhibits exceptional performance, serving as a foundation for the simultaneous detection of various pathogenic bacteria in food products.

Photodynamic therapy has been applied endoscopically to treat early esophageal cancer. However, the long-term survival outcome of this treatment option is unknown in literature. Patients and Method: The patients of early esophageal cancer (clinical stage I) treated with photophrin based photodynamic therapy were analyzed for their long-term survival outcome and compared to those patients undergoing esophagectomy by a single surgeon for stage I disease. Results: There were 15 and 16 patients undergoing PDT and esophagectomy enrolled in the current study respectively. Complete response was achieved in 10 (66.7%) patients after PDT. After adjuvant chemoradiation (CCRT) complete response was achieved in 13 patients (86%). There is no mortality after PDT. Severe complication was detected in 3 patients including trachea-esophageal fistulae, esophageal stenosis and skin photosensitivity respectively. With a median follow-up duration of 110.2 months (+9.6 months) for the patients after PDT, there were 4 and 3 recurrence in the primary tumor site and regional lymph node respectively with 73.3% of successful local control rate of the primary tumor. There were 7 (46.7%) patients died during clinical follow-up of this cohort with 5 (33.3%) from disease progression of esophageal cancer and two from other diseases respectively. The five-year survival rate after PDT is 64.3%, whereas 70.9% of the patients after esophagectomy without significant difference of these two group of patients (P=0.72). Conclusion: Our preliminary results suggested that PDT might provide an equivalent long-term oncological outcome as compared to that done by esophagectomy for early esophageal cancer. A prospective randomized clinical trial comparing the results with esophagectomy and other endoscopic abrasive therapies is warrant in the future.

Keywords: Porcine reproductive and respiratory syndrome virus, baculovirus surface display vectors, neutralizing antibody, IFN-γ, IL-4.

The availability of high quality surface observations of precipitation and volume observations by polarimetric operational radars make it possible to constrain, evaluate and validate numerical models with a wide variety of microphysical schemes. In this article, a novel particle-based Monte-Carlo microphysical model (called “McSnow”) is used to simulate the outer rain bands of Hurricane Dorian which traversed the densely instrumented precipitation research facility operated by NASA at Wallops Island, Virginia. The rain bands showed steady stratiform vertical profiles with radar signature of dendritic growth layers near −15 °C and peak reflectivity in the bright band of 55 dBZ along with polarimetric signatures of wet snow with sizes inferred to exceed 15 mm. A 2D-video disdrometer measured frequent occurrences of large drops >5 mm and combined with an optical array probe the drop size distribution was well-documented in spite of uncertainty for drops <0.5 mm due to high wind gusts and turbulence. The 1D McSnow control run and four numerical “experiments” were conducted and compared with observations. One of the main findings is that even at the moderate rain rate of 10 mm/h collisional breakup is essential for the shape of the drop size distribution.

Cabbage (Brassica oleracea L. var. capitata) plays a very important role in the annual national vegetable supply and export trade. In recent years, the cadmium content of agricultural soils has increased. As a result, cabbage yields and quality have declined significantly. Studies have shown that selenium can counteract the harmful effects of cadmium on plants and can alleviate the stress caused by cadmium during the growth of plants. However, the mechanism of exogenous selenium application in the alleviation of cadmium stress in cabbage seedlings has not been thoroughly investigated. In this study, exogenous selenium (10μMol/L) was applied under cadmium (25μMol/L) stress and the physiological mechanisms such as biomass, photosynthetic pigment, leaf stomata parameters, selenium and cadmium content, chloroplast ultrastructure, active oxygen accumulation, leaf membrane esterification and antioxidant enzyme activity were determined. The protective mechanism of exogenous selenium on cabbage seedlings under cadmium stress was investigated. The re-sults showed that exogenous application of selenium could effectively alleviate the decrease in growth, photosynthetic pigment and gas exchange characteristics of cabbage seedlings under cadmium stress, im-prove cabbage root vitality, reduce root leaf cadmium content and alleviate cadmium stress-induced damage. Ultrastructural observation showed that cadmium stress caused the disruption of the internal structure of chloroplasts of cabbage leaves, while exogenous selenium treatment alleviated the chloroplast damage to some extent, improved the stability of the inner capsule membrane and alleviated the cadmium stress-induced damage to photosynthetic organs. Cadmium stress also caused oxidative damage and ex-cessive accumulation of ROS in the leaves of cabbage seedlings as evidenced by significant accumulation of O2-, H2O2, MDA and electrolyte leakage. On the other hand, after exogenous selenium treatment, cadmium stress- induced oxidative damage could be reduced by up-regulating the activities of antioxidant enzymes SOD, POD and APX. At the same time, cadmium stress significantly increased GSH levels, and exogenous selenium treatment further increased GSH levels, thereby increasing the tolerance of cabbage to cadmium stress. In conclusion, by protecting the photosynthetic system, eliminating excessive accumulation of reactive oxygen species in cadmium-stressed cabbage seedlings, alleviating oxidative stress and reducing cadmium levels in the plant, exogenous selenium can further improve cadmium tolerance in cabbage seedlings.

Electrochemical biosensors based on immobilized enzymes are among the most popular and commercially successful biosensors. Literature in this field suggests that modification of electrodes with nanomaterials is an excellent method for enzyme immobilization, which can greatly improve the stability and sensitivity of the sensor. However, the poor stability, weak reproducibility, and limited lifetime of the enzyme itself still limit the requirements for the development of enzyme electrochemical biosensors for food production process monitoring. Therefore, constructing sensing technologies based on enzyme electrochemical biosensors remains a great challenge. This article outlines the construction principles of four generations of enzyme electrochemical biosensors and discusses the applications of single-enzyme systems, multi-enzyme systems and nano-enzyme systems developed based on these principles. The article further describes methods to improve enzyme immobilisation by combining different types of nanomaterials such as metals and their oxides, graphene-related materials, metal-organic frameworks, carbon nanotubes and conducting polymers. In addition, the article highlights the challenges and future trends of enzyme electrochemical biosensors, providing theoretical support and future perspectives for further research and development of high-performance enzyme chemical biosensors.

Background: We screened key genes involved in the dedifferentiation process of thyroid cancer by analyzing differentially expressed genes in anaplastic thyroid carcinoma (ATC) using Gene Expression Omnibus (GEO) database. Methods: We analyzed differentially expressed genes in ATC from GEO database and constructed a co-expression network using Weighted Gene Co-expression Network Analysis (WGCNA) . Cytoscape was used to calculate top ten key genes based on their gene scores. DEPDC1 was selected as interest gene for further validation, including examination of its prognostic relationship with thyroid cancer, correlation analysis with thyroid differentiation markers, immune cell infiltration, and tumor microenvironment. The impact of DEPDC1 on cancer cell migration, invasion, and proliferation was validated through downregulation and overexpression of DEPDC1 gene in thyroid cancer cell lines c643 and BCPAP. Results: We identified top 10 key genes in ATC: AURKA, TPX2, RACGAP1, MELK, DLGAP5, DEPDC1, KIF2C, NCAPG, CCNB1, and PBK. DEPDC1 showed a strong correlation with the prognosis of thyroid cancer. The odds ratio (OR) for overall survival was 3.5 (P=0.016) in individuals with high DEPDC1 expression, and the OR for disease-free survival was 2.6 (P=0.003). Additionally, the analysis revealed a significant negative correlation between the expression of DEPDC1 and thyroid differentiation markers. Gene Ontology enrichment analysis demonstrated that DEPDC1 co-expressed genes were enriched in cellular processes, cell cycle pathways, and dynamic protein groups. Matrix and immune scoring indicated tumor microenvironment and immune scores were associated with DEPDC1 expression. TIMER2.0 online analysis revealed a strong correlation between DEPDC1 expression and immune cell infiltration in papillary thyroid carcinoma. After downregulation of DEPDC1 expression, the invasion, migration, and proliferation abilities of tumor cells were significantly reduced. Conversely, overexpression of DEPDC1 exhibited the opposite effect. Conclusion: DEPDC1, a newly identified dedifferentiation gene in thyroid cancer, inversely correlated with the degree of differentiation. High expression of DEPDC1 promotes cancer progression and leads to poor prognosis in thyroid cancer.

Studies on the neurobiological causes of anxiety disorders suggest that the GABA system in-creases synaptic concentration and enhances the affinity of GABAA (type A) receptors for ben-zo-diazepine ligands. Flumazenil antagonizes the benzodiazepine binding site of the GABA (γ-aminobutyric acid) type /benzodiazepine receptor (BZR) complex in the central nervous sys-tem (CNS). The integration of the metabolites of flumazenil by LC-tandem mass spectrometry will complete understanding of the in vivo metabolism of flumazenil and accelerate radio-pharmaceutical inspection and registration. The main goal of our study was to investigate using reversed-phase HPLC (PR-HPLC) coupled with electrospray ionization triple quadrupole tan-dem mass spectrometry (ESI-QqQ MS) for the identification of flumazenil and its metabolites in a hepatic matrix. And a carrier-free nucleophilic fluorination with automatic synthesizer for [18F]flumazenil which applied to in vivo nano-positron emission tomography (Nano-PET)/computed tomography (CT) imaging and ex vivo bio-distribution used to analyze in normal rats. The study showed that 50% of the flumazenil was bio-transformed at 60 min by the rat liver homogenate, while one metabolite (M1) was a methyl transesterification product of flumazenil. In a rat liver microsomes system, two metabolites were identified (M2 and M3) as its carboxylic acid and hydroxylated ethylester forms, respectively. [18F]flumazenil in vivo nanoPET/CT imag-ing and ex vivo bio-distribution assay also showed significant effects on GABAA receptor availa-bility in the amygdala, prefrontal cortex, cortex, and hippocampus in the rat brain, worriless about the formation of metabolites. We showed completion of the bio-transformed course of flumazenil by the hepatic system; and [18F]flumazenil can be a good ligand and serve as a PET agent for determination of GABAA/BZR complex for multiplex neurological syndromes in the clinical stage.

Alternative splicing can produce transcripts that affect cancer development and shows potential for cancer diagnosis and treatment. However, intron retention (IR), a type of alternative splicing, has been less systematically studied in cancer biology research. Here, we generated a pan-cancer IR landscape for more than 10,000 samples across 33 cancer types from The Cancer Genome Atlas (TCGA). We characterized differentially retained introns between tumor and normal samples and identified retained introns associated with survival. We discovered 988 differentially retained introns in 14 cancers, some of which demonstrated diagnostic potential in multiple cancer types. We also inferred a large number of prognosis-related introns in 33 cancer types, and the associated genes included well-known cancer hallmarks such as angiogenesis, metastasis, and DNA mutations. Notably, we discovered a novel intron retention event inside 5′UTR of STN1 that is associated with the survival of lung cancer patients. The retained intron reduces translation efficiency by producing upstream open reading frames (uORFs) and thereby inhibits colony formation and cell migration of lung cancer cells. Besides, the IR-based prognostic model achieved good stratification on certain cancers, as illustrated in acute myeloid leukemia. Taken together, we performed a comprehensive IR survey at a pan-cancer level, and the results implied that IR has the potential to be diagnostic and prognostic cancer biomarkers, as well as new drug targets.

The objective of this research is to establish a better understanding of the current landscape of digital learning research and sustainable development by using CiteSpace. First, we retrieved published publications from the Web of Science (2004–2022). Following that, we examined the primary research strengths and important subjects of digital learning from two perspectives: collaboration networks (including collaborative networks across countries, institutions, and authors) and co-citation networks. We examined the co-citation network from three perspectives: cluster analysis, the most active citers, top references. Furthermore, referenced journals, popular themes, and rising trends were examined. These findings indicate the primary study subjects in the field of digital learning, the most intriguing research literature, and each period's emerging research hotspots. Finally, we proposed further study ideas for future paths.

The co-occurrence of depression and obesity has become a significant public health concern worldwide. Recent studies have shown that metabolic dysfunction, which is commonly observed in obese individuals and characterized by inflammation, insulin resistance, leptin resistance, and hypertension, is a critical risk factor for depression. This dysfunction may induce structural and functional changes in the brain, ultimately contributing to depression's development. Given that obesity and depression mutually increase each other's risk of development by 50-60%, there is a need for effective interventions that address both conditions. The comorbidity of depression with obesity and metabolic dysregulation is thought to be related to chronic low-grade inflammation, characterized by increased circulating levels of pro-inflammatory cytokines, and C-reactive protein (CRP). As pharmacotherapy fails in at least 30-40% of cases to adequately treat major depressive disorder, a nutritional approach is emerging as a promising alternative. Omega-3 polyunsaturated fatty acids (n-3 PUFAs) are a promising dietary intervention that can reduce inflammatory biomarkers, particularly in patients with high levels of inflammation, including pregnant women with gestational diabetes, patients with type 2 diabetes mellitus, and overweight individuals with major depressive disorder. Further effort directed to implement these strategies in clinical practice could contribute to improved outcomes in patients with depression and comorbid obesity and/or metabolic dysregulation.

Abstract：The brain often switches freely between focused attention and divergent thinking, and the default mode network (DMN) is activated during brain rest. The discovery, function and characteristics of default mode network all indicate that learning does not stop when the brain "rests". Mental disease can lead to dysfunctional default mode networks, which affects learning adversely. Therefore, default mode network plays an important role in learning. Neural activities such as β-wave rhythm regulation, "subconscious" divergence mode initiation, hippocampal function and neural replay occur during default mode, which also explain that "rest" promotes learning. This paper reveals the role and neural mechanism of default mode network in learning from the neural level, discusses the essential role default mode network plays in learning, and default mode network enables rest to promote learning.

In order to better plan new or update sewer pipe condition assessment protocols, this paper presents systematic comparisons of four most widely-used sewer condition assessment protocols, including the fourth edition of Sewer Rehabilitation Manual (SRM-4) in UK, Pipeline Assessment and Certification Program (PACP) in America, Sewer Physical Condition Grading Protocols (SPCCM) in Canada, and Technical Specification for Inspection and Evaluation of Urban Sewer (TSIEUR) in China. In qualitative comparison, the defects, deduct values and assessment methods of the four protocols were analyzed; in quantitative comparison, protocols were used to evaluate the same 182 sewer pipe segments based on field data and the assessment results were compared. It was found that SRM-4 are the most optimistic with 59% pipes being Grade 1 and Grade 2, while SPCCM gives the most pessimistic results with 62% pipes being Grade 3 and Grade 4. Assessment results by PACP and TSIEUR are in the middle. The main reasons for the different evaluation results were due to the different weight of defect and evaluation methods used.

In recent years, remote sensing technology has been widely used to predict forest stand parameters. In order to compare the effects of different features of remote sensing images and topographic information on the prediction of forest stand parameters, multivariate stepwise regression analysis method was used to build estimation models for important forest stand parameters by using textural and spectral features as well as topographic information of SPOT-5 satellite images in northeastern Heilongjiang Province in China as independent variables. The study results show that the optimal window to predict forest stand parameters using textural features of SPOT-5 satellite image is 9×9; the ability of textural features was better than that of spectral features in terms of predicting forest stand parameters; with the inclusion of topographic information, the accuracy of prediction of all models was improved, of which elevation has the most significant effect. The highest accuracy was achieved when predicting the stand volume (SV) (R²_adj=0.820), followed by basal area (BA) (R²_adj =0.778), accuracy of both above models exceeded 75%. The results show that models combined use of textural, spectral features and topographic information of SPOT-5 images have a good application prospect in predicting forest stand parameters.

Breast cancer is the most common malignancies in women and the second leading cause of cancer death in women. Triple negative breast cancer (TNBC) subtype is a breast cancer subset without ER, PR and HER2 expression, limiting treatment options and presenting a poorer survival rate. Thus, we investigated whether HDACi would be used as potential anti-cancer therapy on breast cancer cells. In this study, we found TNBC and HER2-enrich breast cancers are extremely sensitive to Panobinostat, Belinostat of HDACi via experiments of cell viability assay, apoptotic marker identification and flow cytometry measurement. On the other hand, we developed a bioluminescence based live cell non-invasive apoptosis detection sensor (IADS) detection system to evaluate the quantitative and kinetic analyses of apoptotic cell death by HDAC treatment on breast cancer cells. In addition, the use of HDACi may also be accompanied with chemotherapeutic agent such as doxorubicin to synergic drug sensitivity on TNBC cell (MDA-MB-231), but not in breast normal epithelia cells (MCF-10A), providing therapeutic benefits against breast tumor in clinic.

This purpose of the study presented in this article is to comparing different service quality measurements between Kano and TRIZ that plays the critical roles in the catering industrial. Data collected from a DINESERV questionnaire comprises service-quality standards to increase customer satisfaction of mobile dining car. Finally, the TRIZ is standardized measure designed to improve the idealization of strategy for selecting the most appropriate service quality model. In addition, the preferences of more than one decision maker are internally aggregated into the TOPSIS procedure. All these things provide several important theoretical and practical implications for developing a successful mobile catering app.

An improved anti-noise morphology vision navigation algorithm is proposed for intelligent tractor tillage in a complex agricultural field environment. At first the two key steps, Guided Filtering and improved anti-noise morphology navigation line extraction were addressed in detail. Then the experiments were carried out in order to verify the effectiveness and advancement of the presented algorithm. Finally, the optimal template and it’s application condition were studied for improving the image processing speed. The comparison experiment results show that the YCbCr color space has minimum time consumption of 0.094 s in comparison with HSV, HIS and 2R-G-B color spaces. The Guided Filtering method can effectively distinguish the boundary between the new and old soil than other competing vanilla methods such as Tarel, Multi-scale Retinex, Wavelet-based Retinex and Homomorphic Filtering inspite of having the fastest processing speed of 0.113 s. The extracted soil boundary line of the improved anti-noise morphology algorithm has best precision and speed compared with other operators such as Sobel, Roberts, Prewitt and Log. After comparing different size of image template, the optimal template with the size of 140×260 pixels can meet high precision vision navigation while the course deviation angle is not more than 7.5°. The maximum tractor speed of the optimal template and global template are 51.41 km/h and 27.47 km/h respectively which can meet real-time vision navigation requirement of the smart tractor tillage operation in the field. The experimental vision navigation results demonstrated the feasibility of the autonomous vision navigation for tractor tillage operation in the field using the new and old soil boundary line extracted by the proposed improved anti-noise morphology algorithm which has broad application prospect.

Two-dimensional (2D) bismuth oxyhalides (BiOX) have attracted much attention as potential optoelectronic materials. Expecting for their application diversity, we herewith systematically investigate the tunable properties of 2D BiOX by using first principles calculations. Their electronic and optical properties can be modulated by changing the number of monolayers, applying strain, and/or varying the halogen composition. The bandgap shrinks monotonically and approaches the bulk value, the optical absorption coefficient increases, and the absorption spectrum redshifts, as the layer number of 2D BiOX increases. Carrier transport property can be improved by applying tensile strain, and the ability of photocatalytic hydrogen evolution can be obtained by applying compressive strain. General strain engineering will be effective in linearly tune the bandgap of BiOX in a wide strain range. Strain together with halogen composition variation can tune the optical absorption spectrum to be on demand in the range from visible to ultraviolet. It suggests that that 2D BiOX materials have potential serving as tunable novel photodetectors, can be used to improve clean energy techniques, and are prospective in the field of flexible optoelectronics.

Recent preclinical studies have shown the potential benefits of short-term calorie reduction (SCR) on cancer treatment. In this integrative review, we aimed to identify and synthesize current evidence regarding the feasibility, process, and effects of SCR in cancer patients receiving chemotherapy. PubMed, Cumulative Index to Nursing and Allied Health Literature, Ovid Medline, PsychINFO, and Embase were searched for original research articles using various combinations of Medical Subject Heading terms. Among the 311 articles identified, seven studies met the inclusion criteria. The majority of the reviewed studies was small randomized controlled trials or cohort study with fair quality. The results suggest that SCR is safe and feasible. SCR is typically arranged around the chemotherapy with the duration ranging from 24 to 96 hours. Most studies examined the protective effects of SCR on normal cells during chemotherapy. The evidence supports that SCR had the potential to enhance both physical and psychological wellbeing of patients during chemotherapy. SCR is a cost-effective intervention with great potential. Future well-controlled studies with sufficient sample sizes are needed to examine the full and long-term effects of SCR and its mechanism of action.

Aiming at effectively generating safe and reliable motion paths for quadruped robots, a hierar-chical path planning approach driven by dynamic 3D point cloud is proposed in this article. The developed path planning model is essentially constituted of two layers: global path planning layer and local path planning layer. At the global path planning layer, a new method is proposed for calculating terrain potential field based on point cloud height segmentation. Variable step size is employed to improve the path smoothness. At the local path planning layer, a real-time prediction method for potential collision area and a strategy for temporary target point selection is developed. Quadruped robot experiments were carried out in an outdoor complex environment. The experi-mental results verified that, for global path planning, the smoothness of the path is improved and the complexity of the passing ground is reduced. The effective step size is increased by a maxi-mum of 13.4 times, and the number of iterations is decreased by up to 1/6, compared with the traditional fixed step size planning algorithm. For local path planning, the path length is short-ened by 20%, more efficient dynamic obstacle avoidance and more stable velocity planning are achieved by using the improved dynamic window approach (DWA).

This work aims to develop an integrated fault location and restoration approach for microgrids (MGs). This work contains two parts. Part I presents the fault location algorithm, and Part II shows the restoration algorithm. The proposed algorithms are implemented by particle swarm optimization (PSO). The fault location algorithm is based on network connection matrices, which are the modifications of bus-injection to branch-current and branch-current to bus-voltage (BCBV) matrices, to form the new system topology. The backward/forward sweep approach is used for the prefault power flow analysis. After the occurrence of fault, the voltage variation at each bus is calculated by using the Zbus modification algorithm to modify Zbus. Subsequently, the voltage error matrix is computed to search for the fault section by using PSO. After the allocation of the fault section, the multi-objective function is implemented by PSO for optimal restoration with its constraints. Finally, the IEEE 37-bus test system connected to distributed generations is utilized as the sample system for a series simulation and analysis. The outcomes demonstrated that the proposed optimal algorithm can effectively solve the fault location and restoration problem in MGs.

End-to-end learned image compression codecs have notably emerged in recent years. These codecs have demonstrated superiority over conventional methods, showcasing remarkable flexibility and adaptability across diverse data domains while supporting new distortion losses. Despite challenges such as computational complexity, learned image compression methods inherently align with learning-based data processing and analytic pipelines due to their well-suited internal representations. The concept of Video Coding for Machines has garnered significant attention from both academic researchers and industry practitioners. This concept reflects the growing need to integrate data compression with computer vision applications. In light of these developments, we present a comprehensive survey and review of lossy image compression methods. Additionally, we provide a concise overview of two prominent international standards, MPEG Video Coding for Machines and JPEG AI. These standards are designed to bridge the gap between data compression and computer vision, catering to practical industry use cases.

The exceptional performance advantages of the fiber optic gyroscope (FOG) position it as a dominant player in middle and high-end inertial navigation systems. To prevent the loss of sensor precision caused by algorithm design and simplify the complex modeling strategy in traditional methods. We gradually demonstrate the significant role of Convolutional Neural Network (CNN) in the navigation system based on FOG, and utilize the particle swarm optimization algorithm (PSO) to expedite the convergence of the network. The experimental results demonstrate that the initial alignment method based on deep learning is more accurate than the traditional method. The attitude angle error is reduced by 81.25%, 92.54% and 36.53% respectively. The research provides support for the future application of deep learning in optical navigation systems.

Hemorrhagic shock is the primary cause of death in patients with severe trauma, and the development of rapid and efficient hemostatic methods is of great significance in promoting the life-saving of trauma patients. In this study, polycaprolactone (PCL) nanofiber membrane was prepared by electrospinning technology. The PCL-PDA loading system was developed by modifying the surface of polydopamine (PDA) inspired by mussel adhesion protein, and the efficient and stable loading of thrombin (TB) was realized on the premise of ensuring the bioactivity of TB. The new thrombin loading system overcomes the disadvantages of harsh storage conditions, poor strength, easy to fall off, and can use thrombin to start rapid coagulation cascade reaction, which has the characteristics of fast hemostasis, good biocompatibility, high safety and wide range of hemostasis. The physicochemical properties and biocompatibility of PCL-PDA-TB membrane were verified by scanning electron microscopy, cell proliferation test, cell adhesion test and extract cytotoxicity test. Red blood cell adhesion, platelet adhesion, dynamic coagulation time and animal models all verified the coagulation effect of PCL-PD-TB membrane. Therefore, PCL-PDA-TB membrane has great potential in wound hemostasis.

Patients with lean NAFLD make up an increasing subset of liver diseases. The association between lean NAFLD and feutin-A, which serves as a hepatokine and adipokine, has never been examined. Our study aimed to explore the association of serum fetuin-A among lean and nonlean patients. The study comprised 606 adults from the community, stratified into lean or nonlean (BMI </≥ 24 kg/m2) and NAFLD or non-NAFLD (scoring of ultrasonographic fatty liver indicator, US-FLI ≥ 2/<2). Multivariate logistic regression analyses were performed to estimate the odds ratio of having NAFLD among the tertiles of fetuin-A after adjustment. The least square means were computed by general linear models to estimate marginal means of the serum fetuin-A concentrations in relation to the NAFLD groups. The OR of having NAFLD for the highest versus the lowest tertile of fetuin-A was 2.62 (95% CI: 1.72-3.98; P for trend<0.001). Stratifying by BMI, the OR of having lean NAFLD for the highest versus the lowest tertile of fetuin-A was 2.09 (95% CI: 1.09-3.98; P for trend 0.026), while nonlean NAFLD had no significant association with the fetuin-A gradient after adjustments. Fetuin-A was positively associated with lean NAFLD after adjusting for central obesity and insulin resistance.

The Yixian Formation (Lower Cretaceous) of China is famous worldwide for its fossils of early angio-sperms, but there is only one record of flower bud hitherto. A previous fossil record of flower bud just showed the appearance and lacked any internal details. Such a lacuna in knowledge of flower buds hin-ders our understanding of the evolution of flowers. Our new specimen was collected from an outcrop of the Yixian Formation (the Barremian-Aptian, Lower Cretaceous) near Dawangzhangzi, Lingyuan, Liao-ning, China. The specimen was observed and photographed using a Sony ILCE-7 digital camera and a Nikon SMZ1500 stereomicroscope, and details were observed using a TESCAN MAIA3 SEM. Our ob-servations document a fossil flower bud, Archaebuda cretaca sp. nov, from the Lower Cretaceous of China. The occurrence of two species of Archaebuda in the Yixian Formation not only confirms the ex-istence of the expected gynoecium (and possible androecium) in a flower bud, but also underscores the occurrence of typical flowers in the Early Cretaceous.

Recently, resistive random access memory (RRAM) has been an outstanding candidate among various emerging nonvolatile memories for high density storage and in-memory computing applications. However, the traditional RRAM, which accommodates two states depending on applied voltage, cannot meet the high density requirement in the era of big data. Many research groups have demonstrated that RRAM possesses the possibility of multi-level cell to overcome the demand of mass storage. Among numerous semiconductor materials, gallium oxide, as the fourth-generation semiconductor material, is highly-profile due to its excellent material proper-ties, and already be widely used in optoelectronics, high-power, resistive switching device and so on, due to its wide bandgap and transparent properties. In this study, we have successfully demonstrated the Al/GO/Ga2O3/ITO RRAM to achieve the possibility of two-bit storage. Compared to the single-layer counterpart, the bilayer structure has excellent electrical properties and stable reliability. The endurance characteristics could be enhanced above 100 switching cycles with an ON/OFF ratio of over 103. Moreover, the filament models are also described in this thesis to clarify the transport mechanisms.

Traditional edible barbecue products use with lemon juice not only make the barbecue more delicious but also reduce the risk of PAHs in the barbecue products. One of the major economics crops in Taiwan, the waste from citrus fruits was very tremendous mass. However, the peelings of citrus fruits are rich in essential oil, especially, the limonene is the major. Whether the anti-carcinogenesis activities of terpene, such as limonene, in citrus fruits essential oil extraction. This study to demonstrate the PAHs content in fish skin increased markedly after being roasted at 210℃ for 20 minutes and greater mutagenicity risk of roasted fish skin was observed by Ame's test. The reduction of mutagenicity risk of roasted fish skin, which the antimutagenic abilities of substances in descending order were limonene > cold pressure oil > lemon >grapefruit. The antimutagenicity rate and ability of the three extracts were limonene: 18–23%; cold-pressed lemon oil: 18–22%; and steam distilled lemon essential oil: 8–16%. The obvious anti- mutagenicity effects against the PAHs mutagenicity of roasted fish skins can be found in citrus fruits essential oil extraction.

This paper proposed an optimal tracking control scheme through adaptive dynamic programming(ADP) for a class of partially unknown discrete-time nonlinear systems based on radial basis function neural network(RBF-NN). In order to acquire the unknown system dynamics, we use two RBF-NNs, the one is used to construct the identifier, and the another is used to directly approximate the steady-state control input, where a novel adaptive law is proposed to update neural network weights. While the optimal feedback control and the cost function are derived via feedforward neural networks approximating, it is proposed to regulate the tracking error, the critic network and the actor network are then trained online to obtain the solution of the associated Hamilton–Jacobi–Bellman (HJB) equation being built under the ADP framework. Simulations verify the effectiveness of the optimal tracking control technique using the neural networks.

Nonalcoholic fatty liver disease (NAFLD) and nonalcoholic steatohepatitis (NASH) are fast becoming the most common chronic liver disease and are often preventable with healthy dietary habits and weight management. Sugar-sweetened beverage (SSB) consumption is associated with obesity and NAFLD. However, the impact of different types of SSB, including artificially sweetened beverages (ASB), is not clear after controlling for total sugar intake and total caloric intake. In this study, we examined the association between different SSB consumption and the risk of NAFLD and NASH. A total of 3,739 US adults aged ≥20 years old who had completed 24-hour dietary recall interviews and measurements, including dietary, SSB, smoking, physical activity, and liver stiffness measurement, using the National Health and Nutrition Examination Survey 2017-2020 surveys were included in this study. Chi-square tests, t-tests, and weighted logistic regression models were utilized for analyses. The prevalence of NASH was 20.5%, and NAFLD (defined without NASH) was 32.7% of .S.U.S. adults. We observed a higher prevalence of NASH/NAFLD in men, Mexican-Americans, sugar intake from SSB, light-moderate alcohol use, individuals with lower physical activity levels, higher energy intake, obesity, and medical comorbidities. Heavy sugar consumption through SSB was significantly associated with NAFLD (aOR=1.60, 95% CI=1.05-2.45). In addition, intake of ASB only (compared to non-SSB category) was significantly associated with NAFLD (aOR=1.78, 95% CI=1.04-3.05), after adjusting for demographic, risk behaviors, and body mass index. Higher sugar intake from SSB and exclusive ASB intake are both associated with the risk of NAFLD.

Butyric acid as a histone deacetylase (HDAC) inhibitor was produced by a number of periodontal and root canal microorganisms (such as Porphyromonas, Fusobacterium etc.). Butyric acid may affect the biological activities of periodontal/periapical cells such as osteoblasts, periodontal ligament cells etc., and thus affect periodontal/periapical tissue destruction and healing. The purposes of this study were to study the toxic effects of butyrate on matrix and mineralization markers’ expression of MG-63 osteoblasts. Cell viability and proliferation were determined by 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl tetrazolium bromide (MTT) assay. Cellular apoptosis and necrosis were analyzed by propidium iodide/Annexin V flow cytometry. Protein and mRNA expression of OPG, and RANKL were analyzed by western blotting and RT-PCR. OPG, soluble RANKL (sRANKL), 8-isoprostane, pro-collagen I, MMP-2, osteonectin (SPARC), osteocalcin and osteopontin secretion into culture medium were measured by enzyme-linked immunosorbant assay. Histone H3 acetylation levels were evaluated by immunofluorescent staining (IF) and western blot. We found that butyrate induced morphologic changes of growing MG-63 cells, with bigger and flattened in appearance. Butyrate activated histone H3 acetylation of MG-63 cells. Exposure of MG-63 cells to butyrate partly decreased cell number with no marked increase in apoptosis and necrosis. Butyrate stimulated RANKL protein expression, whereas it inhibited OPG protein expression. Butyrate also inhibited the secretion of OPG in MG-63 cells, whereas sRANKL level was below detection limit. Butyrate stimulated 8-isoprostane, MMP-2 and osteopontin secretion, but not procollagen I, osteonectin, osteocalcin in MG-63 cells. In conclusion, butyric acid generated by periodontal and root canal microorganisms may potentially induce bony destruction and impair bone repair by alteration of OPG/RANKL expression/secretion, 8-isoprostane, MMP-2, and osteopontin secretion, and affect cell proliferation. These effects are possibly related to increased histone acetylation. These events are important in the pathogenesis of periodontal and periapical destruction.

This literature review paper delves into the synergies between Climate-Smart Agriculture (CSA) and the effective management of food losses. With the escalating challenges posed by climate change and the pressing need to address food security concerns, the intersection of these two critical domains becomes paramount for sustainable agricultural practices. The review explores existing research on the implementation of climate-smart agricultural techniques and their impact on mitigating food losses throughout the agricultural value chain. The paper synthesizes findings related to climate-resilient crop varieties, precision farming, water-use efficiency, and sustainable soil management, highlighting their contributions to reducing post-harvest losses and enhancing overall food security. In addition to summarizing current knowledge, this paper identifies gaps in the literature and proposes avenues for future research. This review serves as a foundation for researchers, policymakers, and practitioners seeking to contribute to the advancement of climate-smart agriculture and the reduction of food losses, paving the way for a more sustainable and resilient global food system.

Particulate matter is a severe source of atmospheric pollution in urban cities, and it has adverse effects on human health. This study was conducted during the whole year of 2016 to monitor the concentrations of PM₁₀ and PM_2.5 on the Beijing Hanshiqiao wetland and bare land in Beijing to analyze their correlations with meteorological factors and compare the removal efficiency between two land surface types. The results indicated that (1) the PM₁₀ and PM_2.5 concentrations on the bare land were higher than those on wetland as a whole, reaching the highest value both at night and dusk and the lowest value near noon. The average concentration of PM₁₀ was higher in winter (wetland: 137.48 μg·m^-3; bare land: 164.75 μg·m^-3) and spring (wetland: 205.18 μg·m^-3; bare land: 244.85 μg·m^-3) and the concentration of PM_2.5 on the wetland also reached the higher value in winter and spring with the average of 84.52 μg·m^-3 and 98.98 μg·m^-3, whereas, it was higher in spring and summer on the bare land; (2) concentrations of PM₁₀ and PM_2.5 were significantly positively affected by the relative humidity (P < 0.01) and negatively influenced by wind speed (P < 0.05). The relationship between PM₁₀ and PM_2.5 concentrations and temperature was found complicated: it showed a significantly negative correlation (P < 0.01) in winter and spring and was insignificant in autumn, but in summer, only the correlation between the PM₁₀ concentration and temperature on wetland was significant (P < 0.01); (3) the removal efficiencies of PM₁₀ and PM_2.5 followed the order of spring > winter > autumn > summer on the wetland, and the removal efficiency of PM₁₀ was greater than that of PM_2.5. This study is aim to provide practical measures to improve the air quality and facilitate sustainable development in Beijing.

Laser additively manufactured (LAM) Ti–6Al–4V alloy has huge application potential in aerospace structural parts such as turbine blades. However, there are few studies on the fatigue properties of such LAM parts under vibration loading, particularly with regard to anisotropy. In this paper, vibration fatigue properties of LAM Ti-6Al-4V by laser melted deposition process were investigated along the transversely deposited (TD) direction and parallelly deposited (PD) direction. Through the first-order bending vibration experiments, LAM Ti-6Al-4V alloy exhibits obvious anisotropic fatigue properties and significant dispersion in fracture position. The fracture morphology analysis reveals that the vibration fatigue failure was mainly dominated by the LAM process-induced defects and the microstructure. For the LAM samples without defects at crack initiation sites, the fatigue behavior is controlled by the prior β columnar grains with preferential orientation, which leads to enhanced fatigue crack propagation resistance for the PD samples. For the LAM samples with defects at initiation sites, having lower fatigue lives, the fatigue anisotropy strongly depends on the projection area of the lack-of-fusion defects relative to the loading direction, resulting in better fatigue performance for the TD samples.

A common spinal condition, spondylolisthesis is the presence of a relative back or forth displacement between the upper and lower vertebra due to one vertebra being oriented away from the smooth curvature of a normal spine. Aging-related illnesses such as degenerative spondylolisthesis are especially burdensome on social welfare and health-care systems in an aging society, especially radiologists and clinical physicians. Therefore, we proposed a computer aided diagnosis algorithm, named LumbarNet, for vertebral slippage detection on clinical X-ray images. Collaborating with i) a P-grade, ii) a piecewise slope detection scheme, and iii) a dynamic shift detection routine, LumbarNet was thus specialized for analyzing complex structural patterns in lumbar spine X-ray images and outcompeted other U-Net based methods. Extensive experiments on lumbar spine X-ray images in standard clinical practices showed that LumbarNet achieved a mean intersection over union value of 0.88 in vertebral region detection and an accuracy of 88.83% in vertebral slippage detection.

Currently, data regarding optimal treatment modality, response, and outcome specifically for N3 head and neck cancer are lacking. This study aimed to compare the treatment outcomes between definitive concurrent chemoradiotherapy (CCRT) to the neck and upfront neck dissection followed by adjuvant CCRT. 93 N3 squamous cell carcinoma head and neck cancer patients were included. Primary tumor treatment was divided to definitive CCRT (CCRT group) or curative surgery followed by adjuvant CCRT (surgery group). Neck treatment was also classified into two treatment modalities: definitive CCRT to the neck (CCRT group) or curative neck dissection followed by adjuvant CCRT (neck dissection group). Overall, the 2-year overall survival (OS), local recurrence-free survival (LRFS), regional recurrence-free survival (RRFS), and distant metastasis-free survival (DMFS) were 51.8%, 47.3%, 45.6%, and 43.6%, respectively. In both oropharyngeal cancer and nonoropharyngeal cancer patients, in terms of OS, LRFS, RRFS or DMFS no difference was noted regarding primary tumor treatment (CCRT vs. surgery) or neck treatment (CCRT vs. neck dissection). In summary, N3 neck patients treated with definitive CCRT can achieve similar outcomes to those treated with upfront neck dissection followed by adjuvant CCRT. Cautions should be made to avoid overtreatment for this group of patients.

Halide perovskite materials gain enormous attention for their semiconducting properties, higher power conversion efficiency and potential applications in a wide range field of studies along with their two key limitations: stability and toxicity. In spite of great progress made on the halide perovskites and many promising research developments, overcoming these limitations is not realized yet. Therefore, coordination engineering of new framework for obtaining alternative new halide perovskite materials and fundamental understanding of the coordination chemistry and electronic interactions forming the structure of these newly engineered halide perovskite materials might be one way in order to overcome the issues related to both stability and toxicity. In this review, the current development of halide perovskite families, both lead halide perovskites and lead free halide perovskites followed by coordination engineering of the new frameworks to engineer new halide perovskite materials will be reviewed comprehensively. Moreover, all the concerns of the fundamental ideas of coordination chemistry and electronic interactions that are keys in forming the halide perovskite structures are discussed in detail and form the main aim of this review. Interestingly, we also discuss recent potential energy applications beyond photovoltaic and this review has completed with an essential and open question: ‘what could happen in the future of halide perovskites?’ in order to excite commercial enterprises and research institutions again as well as to get motivating new predictions on the future continuity of this field.

This research focuses on the Hopf bifurcation occurring at a singular point with high-order degeneracy in a class of three-dimensional systems. Based on center manifold theorem, by expanding the technique for determining singular point values of degenerate singularities in two-dimensional systems, the formal series method to determine the singular point values at the high-order degenerate critical point is discussed. Furthermore, a class of specific three-dimensional differential systems with high-order degenerate singularities is explored. By computing the singular point values and determining center conditions, we proved that a minimum of 5 small-amplitude limit cycles in the vicinity of the origin. This research provides new perspectives on the center problem and limit cycle bifurcation in high-dimensional systems with high-order degenerate singular points.

This study investigates the effects of Zinc (4wt.%) and severe plastic deformation on the mechanical properties of AZ61 magnesium alloy through the stir-casting process. The severe plastic deformation (equal channel angular pressing (ECAP)) has been done followed by T4 heat treatment. The microstructural examinations revealed that the addition of 4wt.%Zn enhances the uniform distribution of β-phase, contributing to a more uniformly corroded surface in corrosive environments. Additionally, dynamic recrystallization (DRX) significantly reduces the grain size of as-cast alloys after undergoing ECAP. The attained mechanical properties demonstrate that after a single ECAP pass, AZ61 + 4wt.%Zn alloy exhibits optimal yield strength (YS), ultimate compression strength (UCS), and hardness. This research highlights the promising potential of AZ61 + 4wt.%Zn alloy for enhanced mechanical and corrosion-resistant properties, offering valuable insights for applications in diverse engineering fields.

Streets are an essential element of urban safety governance and urban design, but they are designed with little regard for possible gender differences. This study proposes a safety perception evaluation method from the female perspective based on street view images (SVIs) and mobile phone data, taking the central city of Guangzhou as an example. The method relies on crowdsourced data and uses a machine learning model to predict the safety perception map. It combines the simulation of women's walking commuting paths to analyse the areas that need to be prioritised for improvement. Multiple linear regression was used to explain the relationship between safety perception and visual elements. The results showed the following: 1) There were differences in safety perceptions across genders. Women gave overall lower safety scores and more dispersed distribution of scores. 2) Approximately 11% of the streets in the study area showed weak perceived safety, and approximately 3% of these streets have high pedestrian flows and require priority improvements. 3) Safe visual elements in SVIs included the existence of roads, sidewalks, cars, railways, people, skyscrapers, and trees. Our findings can help urban designers determine how to evaluate urban safety and where to optimise key areas. Both have practical implications for urban planners seeking to create urban environments that promote greater safety.

Antibiotic-loaded bone cement (ALBC) plays a pivotal role in infection prevention and treatment related to musculoskeletal surgery. The release efficacy of antibiotics from ALBC is closely tied to its surface area, yet little is known about the effective release depth. To investigate the relationship between surface area, volume, and antibiotic elution, spheric ALBC specimens with consistent outer diameters but different internal metal sphere diameters were prepared. Two vancomycin doses were utilized in ALBC specimens with an outer diameter of 35 mm: high (4 g) and low (1 g). Each dosage group included five specimens containing embedded metal spheres with diameters of 15, 25, 29, 32, or 33 mm. The resulting shell-like ALBC specimens had thicknesses of 10 mm, 5 mm, 3 mm, 1.5 mm, or 1 mm, respectively. The specimens were immersed in sterile phosphate buffer solution, and antibiotic elution was measured at designated sampling times (1, 3, 6, 10, 24, 48, 72, and 168 hours). Methylene blue was employed to visualize penetration depth. Vancomycin elution did not display statistically significant differences between high- and low-dose groups. In both groups, specimens with 1 mm thickness exhibited a higher vancomycin release efficiency (high-dose group: 18560±5474 μg, 6.7%; low-dose group: 2017±419 μg, 2.6%), decreasing sharply in thicker ALBC specimens. Methylene blue penetration depth showed no apparent difference between high-dose and low-dose groups. ALBC thickness does not significantly impact antibiotic elution, while surface area and antibiotic dose exert notable effects. These in vitro findings offer potential applications in clinical treatments for musculoskeletal infections.

Polymer adhesives have emerged as a promising dielectric passivation layer in hybrid bonding for 3D integration while they raise misalignment problems during curing. In this work, the synergistic effect of oxygen plasma surface activation and wetting is utilized to achieve bonding between completed cured polyimides. The optimized process achieves a void-less bonding with a maximum shear strength of 35.3 MPa at a low temperature of 250 °C in merely 2 min, significantly shortening the bonding period and decreasing thermal stress. It is found that the plasma activation generated hydrophilic groups on the polyimide surface, and the wetting process further introduced more -OH groups and water molecular on the activated polyimide surface. The synergistic process of plasma activation and wetting facilitate bridging polyimide interfaces to achieve bonding, providing an alternative path for adhesive bonding in 3D integration.

EGFR mutations are heterogenous but all carry the same weighting in the Lung-molGPA. The aim of this study was to elucidate the different prognostic implications of molecular subtypes and frontline TKIs in EGFR-mutated lung adenocarcinoma with synchronous brain metastases (BM) using the Lung-molGPA. Medical records were searched in hospital databases from 2011 to 2015. Patients with EGFR-mutated adenocarcinoma and brain metastases who received TKIs were included. The Kaplan-Meier method was used to estimate survival, and multivariate Cox proportional hazard models were used to estimate adjusted hazard ratios (HRs) and 95% confidence intervals (CIs). A total of 256 patients were included with a median overall survival (OS) of 17.2 months. In multivariate analysis of OS, only age (70 versus &lt;70 years, HR:1.71, 95% CI:1.25-2.35, p&lt;0.001), KPS (&lt;70 versus 70, HR:1.71, 95% CI:1.26-2.31, p&lt;0.001), and rare mutations (other versus exon 19 deletions, HR:1.78, 95% CI:1.04-3.05, p=0.037) remained statistically significant. In patients with a Lung-molGPA score 2.5, EGFR molecular subtypes had different median OS (exon 19 deletions versus Leu858Arg versus other, 18.8 vs 12.4 vs 12.1 months, p=0.021). In conclusion, different molecular subtypes treated with frontline TKIs have different prognostic implications in the Lung-molGPA. Further prospective studies are warranted to validate these findings.

Buckling defect will appear on the outer surface of the deformed ring during constrained ring rolling (CRR) of aluminum alloy thin wall conical ring with inner high ribs (AATWCRIHR), if the geometrical dimension of the ribs doesn't match the wall thickness. To avoid the buckling defect, a quantitative method for characterizing the degree of the buckling defect is proposed using the area of buckling profile. Then an orthogonal experimental scheme was designed taking the width of the middle rib, thickness of wall, and height of the middle rib as design variables and defining the area of buckling profile as optimization objective. Subsequently, a quadratic polynomial response surface model was established by combining the optimization algorithm with the finite element method (FEM), and the geometrical dimension of the middle ribs of the deformed AATWCRIHR is optimized. Also the optimal parameter combination to minimize the area of buckling profile is obtained and verified using FE simulation. Results show that the AATWCRIHR after optimization doesn’t generate the buckling defect during constrained ring rolling, and it is proved that the quantitative buckling defect representation method and the optimization design method based on the response surface model and the finite element simulation results are feasible for the constrained ring rolling process of the AATWCRIHR.

Lead-free copper halide perovskite nanocrystals (NCs) are emerging materials with excellent photoelectric properties. Herein, we present a colloidal synthesis route of orthorhombic Cs2CuCl4 NCs with well-defined cubic shape and an average diameter of 24 ± 2.1 nm. The Cs2CuCl4 NCs exhibit bright deep blue photoluminescence, which is attributed to the Cu(II) defects. In addition, passivating the Cs2CuCl4 NCs by Ag+ can effectively improve the photoluminescence quantum yield (PLQY) and environmental stability.

This paper discovers that current variational principle and Noether theorem for different physics systems with (in)finite freedom systems have missed the double extremum processes of the general extremum functional that both is deduced by variational principle and is necessarily taken in deducing all the physics laws, but these have not been corrected for over a century since Noether's proposing her famous theorem, which result in the crisis deducing relevant mathematical laws and all physics laws. This paper discovers there is the hidden logic cycle that one assumes Euler-Lagrange equations, and then he finally deduces Euler-Lagrange equations via the equivalent relation in the whole processes in all relevant current references. This paper corrects the current key mistakes that when physics systems choose the variational extreme values, the appearing processes of the physics systems are real physics processes, otherwise, are virtual processes in all current articles, reviews and (text)books. The real physics should be after choosing the variational extreme values of physics systems, the general extremum functional of the physics systems needs to further choose the minimum absolute extremum zero of the general extremum functional, otherwise, the appearing processes of physics systems are still virtual processes. Using the double extremum processes of the general extremum functionals, the crisis and the hidden logic cycle in current variational principle and current Noether theorem are solved. Furthermore, the new mathematical and physical double extremum processes and their new mathematical pictures and physics for (in)finite freedom systems are discovered. This paper gives both general variational principle and general Noether theorem as well as their classical and quantum new physics, which would rewrite all relevant current different branches of science, as key tools of studying and processing them.

To estimate the progressive collapse resistance capacity of a multi-column frame tube structure with the assembled truss beam composite floor (ATBCF), the pushdown analysis, and the nonlinear dynamic analysis as well, are conducted for such a structure by using the alternate load path (ALP) method. The bearing capacities of the remaining structures at three different work conditions, which are the side middle column failure, the edge middle column failure, and the corner column failure, are individually studied, and the collapse mechanism for the remaining structures is analyzed from the aspects of the internal force redistribution and the failure mode of the second defense line. Simultaneously, the influence of the column failure time on the dynamic response of the remaining structure and the dynamic amplification coefficient are discussed. The results show that the residual bearing capacity of the remaining structure with the bottom corner column failure is higher than that of the one with the side or edge middle column failure, while the latter has a stronger plastic deformation capacity. When the ALP method is adopted to operate the progressive collapse analysis, it is reasonable to take the column failure time as 0.1 times of the first-order vertical vibration period of the remaining structure, and it is suitable to set the dynamic amplification coefficient as of 2.0, which is the ratio of the maximum dynamic displacement to the static displacement of the remaining structure under the transient loading condition.

Accurate segmentation of the Left Ventricle (LV) in Echocardiogram (Echo) images is essential for cardiovascular analysis. Conventional techniques are labor-intensive and exhibit inter-observer variability. Deep learning has emerged as a powerful tool for automated medical image segmentation, offering advantages in speed and potentially superior accuracy. This study explores the efficacy of employing the YOLO (You Only Look Once) segmentation model for automated LV segmentation in Echo images. YOLO, a cutting-edge object detection model, achieves exceptional speed-accuracy balance through its well-designed architecture. It utilizes efficient dilated convolutional layers and bottleneck blocks for feature extraction, while incorporating innovations like path aggregation and spatial attention mechanisms. These attributes make YOLO a compelling candidate for adaptation to LV segmentation in Echo images. We posit that by fine-tuning a pre-trained YOLO based model on a well-annotated Echo image dataset, we can leverage the model's strengths in real-time processing and precise object localization to achieve robust LV segmentation. The proposed approach entails fine-tuning a pre-trained YOLO model on a rigorously labeled Echo image dataset. Model performance has been evaluated using established metrics such as mean Average Precision (mAP) at an Intersection over Union (IoU) threshold of 50% (mAP50) with 98.31%and across a range of IoU thresholds from 50% to 95% (mAP50:95) with 75.27%. Successful implementation of YOLO for LV segmentation has the potential to significantly expedite and standardize Echo image analysis. This advancement could translate to improved clinical decision-making and enhanced patient care.

The primary cilium plays critical roles in homeostasis and development of neurons. Recent studies demonstrate that cilia length is regulated by the metabolic state of cells, as dictated by processes such as glucose flux and O-GlcNAcylation (OGN). The study of cilia length regulation during neuron development, however, has been an area left largely unexplored. This project aims to elucidate the roles of O-GlcNAc in neuronal development through its regulation of the primary cilium. Here, we present findings suggesting that OGN levels negatively regulate cilia length on differentiated cortical neurons derived from human-induced pluripotent stem cells. In neurons, cilia length increased significantly during neurons maturation (after day 35), while OGN levels began to drop. Long-term perturbation of OGN via drugs, which inhibit or promote its cycling, during neuron development also have varying effects. Diminishing OGN levels increases cilia length until day 25, when neural stem cells expand and undergo early neurogenesis, before causing cell cycle exit defects and multinucleation. Elevating OGN levels induces greater primary cilia assembly but ultimately results in the development of premature neurons, which have higher insulin sensitivity. These results indicate that OGN levels and primary cilia length are jointly critical in proper neuron development and function. Understanding the interplays between these two nutrient sensors, O-GlcNAc and the primary cilium, during neuron development is important in paving connections between dysfunctional nutrient-sensing and early neurological disorders.

This paper discovers that current canonical variational principle and canonical Noether theorem of (in)finite freedom systems for different physics systems have neglected doublet extreme value processes of the general extreme value functional that both is derived by variational principle and is necessarily be taken in deriving all ( quantum ) physics laws in phase space, but which have not been done for over one century since Noether's showing her distinguished theorem, which lead to the crisis deriving all (quantum) physics laws (necessary) in phase space. We discover there is the hidden logic cycle that people assume canonical equations, and then they finally deduce canonical equations by the equivalent relation in the whole processes in all current references. We correct the current key mistake concepts that when physics systems take the variational extreme values, the appearing processes of the physics systems are real physics processes, otherwise, are virtual processes in all current references. The real physics should be what after taking the physics systems' variational extreme values, the physics systems' general extremum functional needs to further take the general extremum functional's minimum absolute extremum zero, otherwise, the appearing processes of physics systems still are virtual processes. Conservation current equations and conservation currents, in phase space, of general canonical variational principle and general canonical Noether theorem are, respectively, deduced for the first time. Using the general extremum functionals' doublet extreme value processes, the hidden logic cycle and the crisis in current canonical variational principle and current canonical Noether theorem are solved. Consequently, the new mathematical pictures, classical and quantum new physics in phase space and the new mathematical and physical doublet extremum processes for (in)finite freedom systems are discovered. General canonical variational principle and general canonical Noether theorem naturally are given, which would rewrite all the different sciences in phase space, as key tools of studying and dealing with them.

The article delves into the intricate phase transitions of 1-Octadecanol and n-Nonadecane within a binary system, unveiling dynamic structural changes under varying conditions. Through Fouri-er-transform infrared (FTIR) analysis, specific molecular vibrations were identified, shedding light on the molecular composition and interactions. The study highlights the challenges in detecting subtle phase transitions and emphasizes the individuality of molecular behaviours in closely related compounds. The findings underscore the complexity of phase transitions in binary systems and advocate for a nuanced approach to studying molecular structures and behaviours. Addi-tionally, the research contributes valuable insights into the molecular dynamics of Organic Polymer Functional Adsorption Materials, offering implications for synthetic waxy layers in plant epidermis.

Structural health monitoring has been studied by a number of researchers as well as various industries to keep up with the increasing demand for preventive maintenance routines. This work presents a novel method for reconstruct prompt, informed strain/stress responses at the hot spots of the structures based on strain measurements at remote locations. The structural responses measured from usage monitoring system at available locations are decomposed into modal responses using empirical mode decomposition. Transformation equations based on finite element modeling are derived to extrapolate the modal responses from the measured locations to critical locations where direct sensor measurements are not available. Then, two numerical examples (a two-span beam and a 19956-degree of freedom simplified airfoil) are used to demonstrate the overall reconstruction method. Finally, the present work investigates the effectiveness and accuracy of the method through a set of experiments conducted on an aluminium alloy cantilever beam commonly used in air vehicle and spacecraft. The experiments collect the vibration strain signals of the beam via optical fiber sensors. Reconstruction results are compared with theoretical solutions and a detailed error analysis is also provided.

pH value almost affects the function of cells and organisms in all aspects, so in biology, biochemical and many other research fields, it is necessary to apply simple, intuitive, sensitive, stable detection of pH and base characteristics inside and outside the cell. Therefore, many research groups have explored the design and application of pH probes based on surface enhanced Raman scattering（SERS）. In this review article, we discussed the basic theoretical background of explaining the working mechanism of pH SERS sensors, and also briefly described the significance of cell pH measurement, and simply classified and summarized the factors that affected the performance of pH SERS probes. Some applications of pH probes based on surface enhanced Raman scattering (SERS) in intracellular and extracellular pH imaging and the combination of other analytical detection techniques are described. And finally, the development prospect of this field is prospected.

Nitrogen (N) is a major limiting factor for plant growth and vegetable production. Understanding the regulatory mechanisms of N uptake, transport, and assimilation is key to improving nitrogen use efficiency in plants. Ammonium transporters (AMTs) play an important role in plant N metabolism. In this study, we isolated an important AMT1 subfamily member (BcAMT1;5) with a highly conserved signatural AMT1 subfamily motif from flowering Chinese cabbage. Based on functional complementation in yeast mutant 31019b and overexpression of BcAMT1;5 in Arabidopsis, BcAMT1;5 is a functional ammonium transporter. Tissue expression analysis showed that BcAMT1;5 was mainly expressed in roots and showed multiple N regime transcript patterns to respond to varying nutritional conditions. This was up-regulated by N-deficiency and down-regulated by supplying NH4+. The glucuronidase (GUS) activities of BcAMT1;5pro::GUS showed a similar change in response to different N conditions. Overexpression of BcAMT1;5 accelerated the growth of transgenic seedlings, increased NH4+ net influxes, and enhanced the content and accumulation of NH4+ and NO3- at low N concentrations. Additionally, it increased the transcript levels of N assimilation-related genes in shoots. These results indicate that the transcriptional regulation of BcAMT1;5 in flowering Chinese cabbage may participate in N uptake and assimilation under various N conditions.

The foot-mounted inertial navigation system is an important application of pedestrian navigation as it in principle does not rely any external assistance. A real-time range decomposition constraint method is proposed in this paper to combine the information of dual foot-mounted inertial navigation systems. It is well known that low-cost inertial sensors with ZUPT (zero-velocity update) and range decomposition constraint perform better than in either single way. This paper recommends that the distance of separation between the position estimates of feet-mounted inertial navigation systems be restricted in the ellipsoidal constraint which relates to the maximum step and leg height. The performance of the proposed method is studied utilizing experimental data. The results indicate that the method can effectively correct the dual navigation systems’ position over the existing spherical constraint.

Day-ahead forecasting of electricity prices is important in deregulated electricity markets for all the stakeholders: energy wholesalers, traders, retailers, and consumers. Electricity price forecasting is an inherently difficult problem due to its special characteristic of dynamicity and non-stationarity. In this paper, we present a robust price forecasting mechanism that shows resilience towards aggregate demand response effect and provides highly accurate forecasted electricity prices to the stakeholders in a dynamic environment. We employ an ensemble prediction model in which a group of different algorithms participate in predicting the price for each hour of a day. We propose two different strategies, namely, Fixed Weight Method (FWM) and Varying Weight Method (VWM), for selecting each hour's expert algorithm from the set of participating algorithms. In addition, we utilize a carefully engineered set of features selected from a pool of features derived from information such as past electricity price data, weather data, and calendar data. The proposed ensemble model offers better results than both the Pattern Sequence-based Forecasting (PSF) method and our own previous work using Artificial Neural Networks (ANN) alone do on the datasets for New York, Australian, and Spanish electricity markets.

Silver powder, as the primary component of solar silver paste, significantly influences various aspects of paste performance, including printing, sintering, and conductivity. Silver powders prepared using the liquid-phase reduction method exhibit different microstructures depending on whether the growth process is dominated by aggregation or crystalline growth. This study explores the impact of different silver powder microstructures on packing density and sintering activity. It is observed that polycrystalline aggregated silver powder possesses higher surface energy, lower packing density, and greater sintering activity. Investigation into the influence of different silver powders on the electrical conductivity, adhesion, and structural density of silver paste reveals that polycrystalline aggregated silver powder is more suitable for lower sintering temperature pastes, whereas crystalline growth-type silver powder is better suited for higher sintering temperature pastes, resulting in a denser sintered silver layer. Finally, an analysis of the impact of various silver powders on the aspect ratio and electrical performance of solar cell silver grid lines yields higher aspect ratios (0.40) and photoelectric conversion efficiency (19.26%).

Multimodal remote sensing data classification can enhance the model’s ability to distinguish land features through multimodal data fusion. In this context, how to help models understand the relationship between multimodal data and target tasks is the focus of researchers. Inspired by human feedback learning mechanisms, causal reasoning mechanisms, and knowledge induction mechanisms, this paper integrates causal learning, reinforcement learning, and meta learning into a unified remote sensing data classification framework and proposed the causal meta-reinforcement learning (CMRL). First, based on feedback learning mechanisms, we have overcome the limitations of traditional implicit optimization of fusion features and customized a reinforcement learning environment for multimodal remote sensing data classification tasks. Through feedback interactive learning between agents and the environment, we help them understand the complex relationships between multimodal data and labels, thereby achieving full mining of multimodal complementary information. Second, based on the causal inference mechanism we designed causal distribution prediction action, classification reward, and causal intervention reward, capturing pure causal factors in multimodal data and cutting off false statistical associations between non-causal factors and class labels. Finally, based on the knowledge induction mechanism, we designed a bi-layer optimization mechanism based on meta-learning. By constructing a meta training task and meta validation task simulation model in the generalization scenario of unseen data, we helped the model induce cross-task shared knowledge, thereby improving its generalization ability for unseen multimodal data. The experimental results on multiple sets of multimodal datasets show that the proposed method achieved state-of-the-art performance in multimodal remote sensing data classification tasks.

We consider the financial planning problem of a retiree wishing to enter a retirement village at a future uncertain date. The date of entry is determined by the retiree's utility and bequest maximisation problem within the context of uncertain future health states. In addition, the retiree must choose optimal consumption, investment, bequest and purchase of insurance products prior to her full annuitisation on entry to the retirement village. A hyperbolic absolute risk-aversion (HARA) utility function is used to allow necessary consumption for basic living and medical costs. The retirement village will typically require an initial deposit upon entry. This threshold wealth requirement leads to exercising the replication of an American put option at the uncertain stopping time. From our numerical results, active insurance and annuity markets are shown to be a critical aspect in retirement planning.

Existing research concerning the effects of the sitting birth position during the second stage of labour on maternal and neonatal outcomes remains controversial, and there is a lack of studies to explore its effect on the childbirth experience. The objective of this study is to explore whether the sitting birth position would influence maternal and neonatal outcomes, as well as the childbirth experience reported by Chinese women using the Childbirth Experience Questionnaire (CEQ). A total of 296 women (including primiparous women and multiparous women) were enrolled in our study, and they were divided into the sitting position cohort (n=106) or the lithotomy position cohort(n=116). The study found that primiparous women in the sitting position cohort had a shorter duration of the second stage of labour, higher spontaneous vaginal birth rates, lower episiotomy rates and better childbirth experience (p<0.01). There was no significant difference for perineal lacerations, 2h-postpartum haemorrhage (P>0.05) between the two cohorts of primiparous women. After adjusting for confounding factors through multiple linear and logistic regression analyses, the results remained consistent with those reported above. No neonate in each cohort had Apgar scores at 1min and 5 min postpartum less than 7 or the Cord artery pH less than 7.00, regardless of parity. In addition, among multiparous women, there was no significant difference in any maternal and neonatal outcomes and women’s CEQ scores (p>0.05) between two cohorts. Based on the findings, we recommend that women could take the sitting birth position into account when giving birth for a positive childbirth experience, especially for primiparous women. The study could also serve as a reference for healthcare providers in the management of childbirth positions and the development of high-quality maternal care.

We developed an ovarian cancer-targeted drug delivery system based on a follicle-stimulating hormone receptor (FSHR) peptide. The lipophilic chemotherapeutic drug SN38 and the photosensitizer IR820 were loaded into the phospholipid bilayer of liposomes. Near-infrared laser irradiation stimulated the generation of reactive oxygen species, causing short-term reactive molecular species and spatial-temporal restricted photodamage to the biological targets. The reactive molecular species and spatial-temporal restricted photodamage enhanced the release and uptake of chemotherapy drugs and increased the sensitivity to chemotherapy drugs in ovarian cancer cells. FSH liposomes loaded with SN38 and IR820 (SN38/IR820-Lipo@FSH) were prepared using thin-film hydration-sonication. FSH peptide binding was analyzed using 1H NMR spectrum and Maldi-Tof. The average size and zeta potential of SN38/IR820-Lipo@FSH were 105.1 ± 1.15 nm (PDI: 0.204 ± 0.03) and −27.8 ± 0.42 mV, respectively. SN38/IR820-Lipo@FSH exhibited good drug-loading properties and the in vitro release was slow. FSH significantly increased the uptake of liposomes, inhibited cell proliferation, and induced apoptosis in A2780 cells. Moreover, SN38/IR820-Lipo@FSH exhibited good tumor-targeting ability and anti-ovarian cancer activity in vivo. The SN38/IR820-Lipo@FSH exhibited specific targeting to A2780 ovarian cancer cells. The combination of chemotherapy and photodynamic treatment based on an FSH peptide-targeted delivery system may be an effective approach to treating ovarian cancer.