With heat treatments to control drywood termites (Blattodea: Kalotermitidae), the presence of heat sinks causes heat to be distributed unevenly throughout the treatment areas. Drywood termites may move to galleries in heat sink areas to avoid exposure to lethal temperatures. Our studies were conducted in Crytotermes brevis-infested condominiums in Honolulu, Hawaii to reflect real-world condominium scenarios; either a standard heat treatment performed by a heat remediation company or an improved heat treatment was used. For improved treatments, heated air was directed into the toe-kick voids of C. brevis infested cabinets to reduce heat sink effects and increase the heat penetration into these difficult-to-heat areas. Eight thermistor sensors placed inside toe-kick voids, treatment zone, embedded inside cabinets’ sidewalls, and in a wooden cube recorded target temperatures of above 46 °C or 50 °C for 120 minutes. A pretreatment and follow-up inspections were performed at 6 months posttreatment to monitor termite inactivity using visual observations and by recording the numbers of spiked peaks on a microwave technology termite detection device (Termatrac). In improved treatment condominiums, significantly higher numbers of spiked peaks were recorded at pretreatment as compared to 6 months posttreatment. Efficacious heat treatment protocols using the improved methods are proposed.

This study aims to identify factors associated with anxiety levels of adults living in Singapore before the pandemic and during the COVID-19 outbreak. Data were collected using a cross-sectional web-based survey conducted from July to November 2020 accruing 264 eligible participants. Ordered logistic regression was used to assess Generalized Anxiety Disorder-7 (GAD-7), ranked as minimal (0-4), mild (5-9), moderate (10-14), and severe (15-21) before the pandemic and during the pandemic. About 74% of participants were female, 50% were aged 25-34, and 50% were married. The GAD-7 level went up from pre-pandemic for both moderate (from 12.5% to 16%) and severe GAD (from 2% to 11%). Alcohol consumption (AOR 1.79, 95% CI 1.04-3.06), loneliness (AOR 1.28, 95% CI 1.05-1.54), and difficulty in switching off social media (AOR 2.21, 95% CI 1.29-3.79) predicted increased GAD-7 levels. The quality of life (AOR 0.84, 95% CI 0.79-0.90) was significantly associated with decreased GAD-7 levels. The results heighten the awareness that early initiation of mental health support is crucial for the population in addition to the various financial support measures provided by the government as they are adapting to live with the COVID-19 pandemic.

This paper investigates the hydroelastic responses of offshore floating solar photovoltaic farms (OFPVs) to minimize structural motion. The OFPV usually occupies a large sea space in the order of hectares and due to its huge structural length-to-thickness ratio, the structural deformation under wave action has to be taken into consideration. The flexible deformation of the structure under hydrodynamic loading is termed the hydroelastic response. Due to the relatively long structural length with respect to the encountering wavelength, the diffraction and radiation of waves have to be taken into account to accurately represent the hydrodynamic loadings on the floating platform. The numerical model is first validated by comparing the eigenvalues and eigenvectors of the OFPV obtained from the proposed numerical scheme with their counterparts obtained from an established finite element software. This is followed by the investigation of the hydroelastic response of various OFPVs designed in varying layout configurations. The various layout configurations are obtained by altering the floating modular units’ dimensions as well as the spacing of the OFPVs when deployed adjacent to each other. The optimal configuration that gives the best performance in terms of the overall smallest response, known as compliance, is then suggested. The results suggest that a longish OFPV layout has a lower hydroelastic response and the motion could be further reduced by increasing the global flexural stiffness via layout arrangement.

The vibration propagates in a media such as a shaft in the form of elastic waves. The propagation characteristics of the waves are affected by the geometry of the media, the material properties as well as the cracks. The study to elastic waves propagating in a shaft with transverse cracks can help to detect them. The transverse crack possesses different crack modes due to different external loads. The influence of the crack mode, the location and the depth to the propagation characteristics is investigated in this paper. Firstly, the local flexibility coefficients with three different modes are deduced. And then, the transfer matrix of the elastic wave can be obtained. Finally, the influence of the crack mode, the location and the depth of the transverse crack as well as the rotating speed to the propagation characteristics is then studied, both in a numerical and an experimental way. It’s found that mode III is the most suitable mode in this paper, the location of the crack will make the stopbands fluctuating, the depth mainly affects the bandwidth of the stopbands, and the increase of the rotating speed will shift up the stopbands without changing their bandwidths.

Academic conferences offer scientists the opportunity to share their findings and knowledge with other researchers. However, the number of conferences is rapidly increasing worldwide. Unlike journals that possess accreditation indices, there is no appropriate accreditation for international conferences. Here, a bibliometric measure is proposed that enables scholars to evaluate conference quality before attending.

Abstract: An Al-Co-Y diffusion coating was prepared on a TiAl alloy by pack cementation process at a low temperature range of 650-720 ℃. The influence of different activators and co-deposition temperatures on the coating’s microstructure and formation process, and high temperature oxida-tion performance was studied. The results showed that NaF was a more suitable activator for preparing the Al-Co-Y diffusion coating on TiAl alloy compared to NH4Cl and AlCl3. A more compact coating structure can be obtained when deposition was performed at 680 ℃ using NaF as the activator. The coating was mainly composed of a TiAl3 outer layer, a TiAl2 inner layer, and a thin Al-rich TiAl inter-diffusion layer. The growth of the coating exhibited a positive linear correlation between coating thickness increase and the square root of deposition time. The high-temperature oxidation tests showed that a dense scale mainly composed of Al2O3 and a small amount of TiO2 formed on the coating after oxidation at 950 ℃ for 100 h. The scale possessed excellent high-temperature oxidation resistance, with a parabolic rate constant of the oxidation weight gain approximately 4.9×10-3 mg2/cm4 h, which is lower than that of the TiAl substrate by about three orders of magnitude, and lower than that of the pure Al diffusion coating more than one order of magnitude.

In a global context, the story of the Jesuit compound in Shanghai, since its establishment by French Jesuits in 1847, reflected not only conflicts between rival powers in Europe but also the fight for their interests in the Eastern world. The Pope, who was stuck without legal status in the Vatican after 1861, was also seeking the chance to save the authority of the Church in the face of questions regarding the extent of his temporal power and the status of Rome in the context of Italian unification. As in the Reformation, a break-through in the east seemed to offer a solution for losses in Europe. However, the Jesuits to the East in the late 19th century were not only troops working and fighting on behalf of the Pope; their identities under the French Protectorate added complexity to an already complicated story involving not just the Church, but the course of world history.The female Catholic orders at the east bank of Zi-ka-wei compound became a unique window to approach the complexity.

The resource allocation for tasks in heterogeneous distributed system is a well known NP-hard problem. For the sake of making the makespan is minimized, it is hard to distribute the tasks to proper processors. The problem is even more complex and challenging when the processors have unavailable time and the tasks type are various. This paper investigates a resource allocation problem for hybrid tasks comprising both divisible and bag-of-tasks(BoT) in heterogeneous distributed system when the processors has unavailable time. First, the mathematical model, which minimizes the makespan of the hybrid tasks when the processors have unavailable time, is established. Second, we propose a scheduling algorithm referred to as bag-of-tasks allocate-pull and divisible task allocation (BoTAPDTA) algorithm for handling hybrid tasks on heterogeneous distributed systems. In addition, to solving the optimization model efficiently, a generic algorithm(GA) is proposed. For the sake of reducing the search space and solving the optimization model effectively, a two step scheduling algorithm(TSGA), which first allocate bag-of-tasks(BoT) using generic algorithm and then assign divisible task to processors like BoTAPDTA, is designed. Finally, numerical simulation experiments are conducted, and experimental results indicate the effectiveness of the proposed model and algorithm.

Scattering hyperspectral technology is a nondestructive testing method with many advantages. Here, we propose a method to improve the accuracy of egg freshness, research the influence of incident angles of light source on the accuracy and explain its mechanism. A variety of weak classifiers classify eggs based on the spectra after preprocessing and feature wavelength extraction to obtain three classifiers with the highest accuracy. The three classifiers are used as metamodels of stacking ensemble learning to improve the highest accuracy from 96.25% to 100%. Moreover, the highest accuracy of scattering, reflection, transmission and mixed hyperspectral of eggs are 100.00%, 88.75%, 95.00% and 96.25%, respectively, indicating that the scattering hyperspectral for egg freshness detection is better than that of the others. In addition, the accuracy is inversely proportional to the angle of incidence due that the smaller the incident angle, the camera collects a larger proportion of scattering light, which contains more biochemical parameters of an egg than that of reflection and transmission. These results are very important for improving the accuracy of non-destructive testing and selecting the incident angle of the light source, and have potential applications in online non-destructive testing.

Thyroid cancer is the most prevalent malignancy of the endocrine system and the ninth most common cancer globally. Despite the advances in the management of thyroid cancer, there are critical issues with the diagnosis and treatment of thyroid cancer that result in the poor overall survival of undifferentiated and metastatic thyroid cancer patients. Recent studies have revealed the role of different non-coding RNAs (ncRNAs), such as microRNAs (miRNAs), long non-coding RNAs (lncRNAs) and circular RNAs (circRNAs) that are dysregulated during thyroid cancer development or the acquisition of resistance to therapeutics, and may play key roles in treatment failure and poor prognosis of the thyroid cancer patients. Here, we systematically review the emerging roles and molecular mechanisms of ncRNAs that regulate thyroid tumorigenesis and drug response. We then propose the potential clinical implications of ncRNAs as novel diagnostic and prognostic biomarkers for thyroid cancer.

Alginate extraction is from seaweed, and lignin separation is from by-product corn (stalks and leaves). Alginate/lignin is a synthetic polymer rich in biological activity of great interest. Antioxidant activities of alginate/lignin were evaluated, such as total antioxidant activity, reducing power activity, DPPH free radical scavenging activity, and α – glucosidase inhibition activity. The test of anticancer activity was on four cell lines (Hep G2, fibroblast, MCF-7, and NCI H460). Determination of physical-chemistry characteristics of alginate/lignin was through FTIR, DSC, SEM_EDS, SEM_EDS mapping, XRD, XRF, and 1H-NMR. A study of acute toxicity of alginate/lignin was on Swiss albino mice. The results showed alginate/lignin possessed antioxidant activity such as total antioxidant activity, reducing power activity, especially, α – glucosidase inhibition activity, and no free radical scavenging activity. Alginate/lignin did not be typical in cancer cell lines. Alginate/lignin existed in a thermally stable regular spherical shape in the investigated thermal region. Some specific functional groups of alginate and lignin did not exist in alginate/lignin crystal. Elements such as C, O, Na, and S were popular in the alginate/lignin structure. LD0 and LD100 of alginate/lignin in mice were 3.91 g/kg and 9.77 g/kg, respectively. Alginate/lignin is the potential for application as pharmaceutical materials, functional foods, and supporting diabetes treatment.

Urbanization-induced land use transition results in a decline in ecosystem services, which has implications for regional ecological security. In order to explore the relationship between ecosystem services and land use transition, this paper utilizes the InVEST model, geographically weighted regression model to examine the impact of land use transition on ecosystem services in the Dongting Lake area (DLA). The results showed that (1) During the period 2000-2020, the intensity and motivation of land-use transition showed obvious spatial and temporal heterogeneity with the variation of urbanization development. (2) Habitat quality and Carbon sequestrations showed a downward trend. In contrast, food supply followed an upward trend; soil conservation and water yield services initially increased and dropped later. The overall spatial changes in habitat quality and Carbon sequestration appear to be insignificant. Food supply shows significant differences in the plains compared to other areas; while soil conservation and water yield service shows significant changes in places other than the DLA. (3) From 2000 to 2020, land use transition dynamics, population density, GDP density, night lighting and transition intensity had mainly negative effects on ecosystem services. Only the Normalized Vegetation Index (NDVI) showed a positive effect on ecosystem services. The results of the research will provide valuable references for the development and implementation of spatial ecological restoration planning and land use policies in the national territory.

Changing climate conditions and rapidly increasing carbon dioxide emissions have severely affected the global ecosystem and world economy. Governments around the world have paid attention to these resulting challenges and enacted many policies to reduce environmental pollution and carbon dioxide (CO2) emissions. This study aimed to determine and understand the relationship between innovation, foreign direct investment, economic growth, renewable consumption and CO2 emission in Vietnam. Information was collected annually based on the annual data of the General Statistics Office of Vietnam and World Bank from 2000 to 2022. Data processing was conducted using the STATA 17.0 software. The innovation affects Vietnam’s environmental pollution. Innovation positively affect environmental pollution in Vietnam; if Vietnam’s innovation were to increase by 1%, CO2 emissions would increase by 0.68%. The empirical research results of this study also show that renewable energy consumption has a negative effect on environmental pollution in Vietnam; if renewable energy were consumed at a 1% increase, CO2 emission would decrease by 0.51%. In addition, FDI inflows and economic growth have strongly positive affecting to environmental pollution; if Vietnam’s FDI inflows were to increase 1%, CO2 emissions would increase 1.39%; if Vietnam’s GDP increase 1% then CO2 emission would increase 1.26%. This paper also provides some recommendations that can assist Vietnam in developing a green and sustainable economy in the technology revolution 4.0 to achieve the United Nations Sustainable Development Goals (SDGs) over a long-term period.

Utilizing unmanned aerial vehicles (UAVs) to facilitate wireless communication has emerged as a viable and promising strategy aimed at enhancing both current and prospective wireless systems. This approach offers many advantages by establishing line-of-sight connections, optimizing operational efficiency, and enabling flexible deployment capabilities in various terrains. Thus, in this paper, we investigate UAV communication in a relaying network in which a UAV helps communication between a source and two destination users while flying to a location. To have a complete view of our proposed system, we consider both orthogonal multiple access as OFDM and non-orthogonal multiple access (NOMA) scenarios. Moreover, we apply successive convex optimization (SCO) and the Block-coordinate gradient descent (BCGD) for the sum-rate optimization problems to improve the system performance under constraints of total bandwidth and total power at the ground base station and UAV. The experimental results validate that the achievable secrecy rates are notably enhanced by using our proposed algorithms and show optimal trends for critical parameters, such as transmit powers, the flight trajectory and speed of UAV, and resource allocation of OFDM and NOMA.

Three Dimensional Variational data assimilation or analysis (3DVAR) is one of most classical methods for providing the initial values for numerical models. In this method, the dimensions of the background error covariance and the observational error covariance matrices are large. Therefore, it is difficult to get the inverse of the covariance matrices and to reduce the orders of these matrices without information loss. With the use of the Sylvester Equation, on the basis of a new linear regression, a new cost function for 3DVAR was given. For the first-guess m×n field, there is an approximate 1−(m²+n²)/(mn×mn) reduction with m>1 & n>1 by using the cost function. The results of the numerical experiments show that the effect of this algorithm is no worse than that of the old cost function for 3DVAR.

In nonlinear self-consistent system, Lorenz system (Lorenz equations) is a classic case with chaos solutions which are sensitively dependent on the initial conditions. As it is difficult to get the analytical solution, the numerical methods and qualitative analytical methods are widely used in many studies. In these papers, Runge-Kutta method is the one most often used to solve these differential equations. However, this method is still a method based on explicit time scheme, which would be the main reason for the chaotic solutions to Lorenz system. In this work, numerical experiments based on implicit time scheme and explicit scheme are setup for comparison, the results show that: in implicit time scheme, the numerical solutions (counterexamples) are without chaos; for an original volume, the volume shrinks exponentially fast to 0 in common.

Extracts of Cordyceps militaris which possess the bioactive capacity such as antimicrobial activity and DPPH-free radical scavenging capacity, are applied to the serum product. This finished serum product has been evaluated the in vitro bioactivity and the stability with expect to find out a good extract with a suitable percentage used for serum product as natural materials on preservatives and antioxidation.

Today, more than 70 million tons of lignin are produced by the pulp and paper industry every year. However, the utilization of lignin as a source for chemical synthesis is still limited due to the complex and heterogeneous lignin structure. The purpose of this study was a selective photodegradation of industrially available kraft lignin in order to obtain appropriate fragments and building block chemicals for further utilization, e.g. polymerization. Thus, kraft lignin obtained from soft wood black liquor by acidification was dissolved in sodium hydroxide and irradiated at a wavelength of 254 nm with and without the presence of titanium dioxide in various concentrations. Analyses of the irradiated products via SEC showed decreasing molar masses and decreasing polydispersity indices over time. At the end of the irradiation period the lignin was depolymerised to form fragments as small as the lignin monomers. TOC analyses showed minimal mineralisation due to the depolymerisation process.

Food-grinding occurs in rodents and is influenced by multiple-factors. However, the factors affecting this behavior remain unclear. In this study, we aimed to investigate the effect of food restriction on food grinding by Brandt’s voles (Lasiopodomys brandtii), as well as the potential role of the gut microbiota in this process, through a comparison of the variations between voles with different food supplies. Food restriction reduced the relative amount of ground food to a greater extent than it lowered the relative food consumption, and altered the abundance of Staphylococcus, Aerococcus, Jeotgalicoccus, and Un--s-Clostridiaceae bacterium GM1. Strong correlations between the ground-to-consumed food ratio and the abundance of fecal microbiota were found for Un--s-Clostridiaceae bacterium GM1 and Aerococcus. The content of fecal acetate and propionate for the 7.5 g-food supply group was lower than that for the 15 g-food supply group. Further, the relative amount of ground food and ground-to-consumed food ratio were both positively correlated with the acetate content. Our study indicated that food restriction can effectively inhibit food grinding. Further, Un--s-Clostridiaceae bacterium GM1 abundance, Aerococcus abundance, and acetate content were strongly related to food grinding. Variations in gut microbial abundance and metabolite short-chain fatty acid content induced by food restriction likely promote the inhibition of food grinding. These results could potentially provide guidance for reducing food waste during laboratory rodent maintenance.

Background: After allogeneic hematopoietic stem cell transplantation (allo-HSCT), acute leukemia relapse is common, and asymmetric bone marrow recurrence hasn’t been reported. Because the anatomical distribution of acute leukemia clones in the bone marrow after allo-HSCT is presumed to be diffuse, bone marrow aspirations are performed in single site. Case presentation: We identified two acute leukemia patients, whose leukemic burden in bilateral bone marrow specimens differed significantly. The first case was a 20-year-old man who was diagnosed with acute myelomonocytic leukemia and received haploidentical allo-HSCT. He had been in complete remission for two years and off immunosuppressive medications for a year, with normal peripheral blood count. Routine bone marrow biopsy of his left posterior iliac bone marrow showed 52% leukemia blasts, while the right side had 0% blasts ten days later. Due to the discordant results, the patient refused further intervention and died of high leukocyte syndrome four months later. The second case was a 23-year-old woman who was diagnosed with acute B lymphoblastic leukemia and received HLA-identical sibling allo-HSCT. Although 62% of blasts were found in her left iliac marrow on day +122, 0 % of blasts were found on a sample obtained from the right iliac crest on day +128. Whole-body 18F-FDG PET/CT scans confirmed that the leukemic infiltration in her bone marrow was asymmetric. Considering the higher leukemic burden on the left, we chose the left posterior iliac crest aspiration for further response evaluation. After chemotherapy combined with donor lymphocyte infusion, she achieved transient hematologic complete remission. She died of septic shock with heart failure at +258 days after allo-HSCT before infusion of anti-CD19 donor chimeric antigen receptor T cells. Conclusions: To our knowledge, these are the first case reports of asymmetric bone marrow infiltration of blasts in acute leukemia patients after allo-HSCT. Bilateral posterior iliac crest aspirations or 18F-FDG-PET/CT scans may help distinguish such distribution. If discordant bone marrow specimens are observed, physicians should restrict future bone marrow studies to the more involved side.

In this paper, we have used magnetron sputtering to grow the high-quality GeSn layer on Ge (100) with Sn compositin up to 7%. The crystallinity of the GeSn layer is pretty good, and the strain relaxation degree of the GeSn layer is evaluated to be approximately 50%. The root mean square (RMS) value is 0.8 nm, and the averaged TDDs in the GeSn layer is 8.7×109 cm-2, which is obtained from the rocking curve of GeSn layer along (004) plane. PL measurement result shows the significant optical emission from the deposited high-quality GeSn layer, which also means that magnetron sputtering is an optional way to achieve the higher Sn composition GeSn luminescent material. To verify whether our deposited GeSn can used for optoelectronic devices, we fabricate the simple vertical p-i-n diode, and the room temperature current-voltage (I-V) characteristic was obtained. This result paves the way for future sputtered-GeSn optimization, which is critical for the optoelectronic application.

Viruses can induce the fusion of infected and neighboring cells, leading to the formation of syncytia. Cell-cell fusion is mediated by viral fusion proteins on the plasma membrane of infected cells that interact with cellular receptors on neighboring cells. Viruses use this mechanism to spread rapidly to adjacent cells or escape host immunity. For some viruses, syncytium formation is a hallmark of infection and a known pathogenicity factor. For others, the role of syncytium formation in viral dissemination and pathogenicity remains poorly understood. Human cytomegalovirus (HCMV) is an important cause of morbidity and mortality in transplant patients and the leading cause of congenital infections. Clinical HCMV isolates have broad cell tropism but differ in their ability to induce cell-cell fusions, and little is known about the molecular determinants. We developed a system to analyze HCMV glycoprotein B (gB) variants in a defined genetic background. HCMV strains TB40/E and TR were used as vectors to compare the fusogenicity of six gB variants from congenitally infected fetuses with those from three laboratory strains. Five of them conferred the ability to induce fusion of MRC-5 human embryonic lung fibroblasts to one or both backbone strains, as determined by a split GFP-luciferase reporter system. The same gB variants were not sufficient to induce syncytia in infected ARPE-19 epithelial cells, suggesting that additional factors are involved. The system described here allows a systematic comparison of the fusogenicity of viral envelope glycoproteins and may help to clarify whether fusion-promoting variants are associated with increased pathogenicity.

Atypical Anorexia Nervosa (AAN) had been found to have significant physical and psychological complications at presentation but has not been described in a multi-ethnic Asian population. This retrospective cohort analysis aimed to characterize the baseline presentation of adolescents with Anorexia nervosa (AN) (N=317) and AAN (N=141) in an Asian cohort that presented to a specialist paediatric eating disorder program between January 2010 to October 2020 for assessment. In patients with AAN, there were increased proportions of males (16% vs 7%) and of Malay ethnicity (11% vs 4%) compared to AN. Adolescents with AAN had lower admission rates (61% vs 81%) as well as lower rates of bradycardia (45% vs 75%) and hypotension (7% vs 21%) but higher rate of syncope (13% vs 7%) compared to adolescents with AN. However, adolescents with AAN had higher frequency of psychological complications including self-harm and drug overdose (14% vs 1.5%) requiring admission as well as higher rates of purging (45.1% vs 14.8%) and for Eating Disorder Questionnaire score in the shape domain was more severe. Asian adolescents with AAN manifest with physical complications of malnutrition and had worse eating disorder psychopathology with higher frequency of other psychological co-morbidities underlining the severity of the illness.

The study comprehensively evaluated the prognostic roles of PLR, NLR, MLR, BLR, and ELR in patients with acute exacerbation chronic obstructive pulmonary disease (AECOPD). 619 patients with AECOPD and 300 healthy volunteers were retrospectively included into the study. The clinical characteristics containing laboratory findings of the AECOPD patients and the blood cell counts (CBCs) of the healthy volunteers were collected. Compared with the healthy volunteers, PLR, NLR, and MLR were elevated in COPD patients in stable condition, and were further ele-vated during exacerbation. ELR showed the opposite trend. PLR, NLR, and MLR were all posi-tively correlated with hospital LOS as well as CRP. In contrast, ELR was negatively correlated with hospital LOS as well as CRP. Elevated PLR, NLR, and MLR were all associated with more serious airflow limitation in AECOPD. Elevated PLR, NLR, and MLR were all associated with increased in-hospital mortality while Elevated ELR was associated with decreased in-hospital mortality in AECOPD. A nomogram was construct to predict in-hospital mortality in AECOPD. The nomo-gram had a C-index of 0.850 (95% CI: 0.799 – 0.901) with good predictive value and clinical ap-plicability. In summary, PLR, NLR, MLR, and ELR served as predictors for clinical outcomes in patients with AECOPD.

Intestinal commensal microbes, called the gut microbiota, play a critical role in host immune homeostasis through active microbial metabolites and innate and adaptive immune responses. Dysbiosis or imbalance of the gut microbiota composition is associated with inflammatory bowel disease (IBD) which includes Crohn’s disease and ulcerative colitis. The incidence and prevalence rates of IBD have been increasing worldwide. It is well recognized that butyrate, a microbial metabolite of diet fibers, is a major energy source for colonocytes and plays a crucial role in regulating immune function and maintaining epithelial barrier function and intestinal homeostasis. Emerging evidence suggests that butyrate might be a potential therapeutic agent to treat IBD. In this review, we discuss about gut microbial metabolites, particularly butyrate, the synthesis and metabolism of butyrate, mechanisms of butyrate in immune and epithelial barrier function. Furthermore, we review the current research on various therapeutic implications of butyrate in IBD.

The pursuit of sustainable wellbeing is one of the research objectives of positive experience design. Driven by this goal, the purpose of this paper is to provide an impact-centered sustainable positive experience design model. Firstly, the literature review method was used to define the research status and concept of impact-centered sustainable design. Secondly, an impact-centered sustainable positive experience design model was constructed, and relevant formulas for concept generation and concept evaluation were proposed. Thirdly, design verification was conducted through a workshop. Finally, the Technology Acceptance Model (TAM) questionnaire was used to evaluate and discuss the design model. An impact-centered sustainable positive design model was proposed, which includes the important impact dimensions of sensory experience and meaningful experience on users’ quality of life at different levels: healthy living (pleasure index, health behavior), harmonious community (social connectivity, social contribution), and livable environment (living environment, environmental contribution). Based on positive experience related theory, this study takes long-term impacts as the starting point for sustainable positive experience design, which helps designers to generate design concepts from a systematic and long-term perspective.

Atherosclerosis (AS) is a chronic progressive disease caused by various factors, and causes various cerebrovascular and cardiovascular diseases (CVDs). Reducing the plasma levels of low-density lipoprotein-cholesterol (LDL-C) is the primary goal in preventing and treating AS. Proprotein Convertase Subtilisin/Kexin Type 9 (PCSK9) plays a crucial role in regulating LDL-C metabolism. Panax notoginseng has potent lipid-reducing effects and protects against CVDs, and its saponins induce vascular dilatation, inhibit thrombus formation, and are used in treating CVDs. However, the anti-AS effect of the secondary metabolite, 20(S) -protopanaxatriol (20(S)-PPT), remains unclear. In this study, the anti-AS effect and molecular mechanism of 20(S)-PPT were investigated in vivo and in vitro by western blotting, real time-polymerase chain reaction (RT-PCR), Enzyme-linked Immunosorbent Assay (ELISA), immunofluorescence staining, and other assays. The in vitro experiments revealed that 20(S)-PPT reduced the levels of PCSK9 in the supernatant of HepG2 cells, upregulated low density lipoprotein receptor (LDLR) protein levels, promoted LDL uptake by HepG2 cells, and reduced PCSK9 mRNA transcription by upregulating the levels of FoxO3 protein and mRNA and decreasing the levels of HNF1α protein and mRNA. The in vivo experiments revealed that 20(S)-PPT upregulated aortic αSMA expression, increased the stability of atherosclerotic plaques, and reduced aortic plaque formation induced by a high-cholesterol fed in ApoE-/- mice (HCF group). Additionally, 20(S)-PPT reduced the aortic expression of CD68, reduced inflammation in the aortic root, and alleviated the hepatic lesions in the HCF group. The study revealed that 20(S)-PPT inhibited LDLR degradation via PCSK9 to alleviate AS.

Nanocomposites of TiO₂ Degussa P25 nanoparticles/activated carbon (TiO₂/AC ) were prepared at various mass ratios of (4:1), (3:2), (2:3), and (1:4) by a facile process. The effects of TiO₂/AC mass ratios on the structural, morphological, and photocatalytic properties were systematically studied in comparison with bare TiO₂ and bare AC. TiO₂ nanoparticles exhibited dominant anatase and minor rutile phases, and a crystallite size of approximately 21 nm; while AC had XRD peaks of graphite and carbon, and a crystallite size of 49 nm. The composites exhibited tight decoration of TiO₂ nanoparticles on micron-/submicron AC particles, and uniform TiO₂/AC composites were obtained as evidenced by the uniform distribution of Ti, O, and C in an EDS mapping. Moreover, Raman spectra show the typical vibration modes of anatase TiO₂ (e.g., E_1g⁽¹⁾, B_1g⁽¹⁾, E_g⁽³⁾) and carbon materials with D and G bands. The TiO₂/AC with (4:1), (3:2), and (2:3) possessed higher reaction rate constants (k) in photocatalytic degradation of methylene blue (MB) than that of either TiO₂ or AC. Among the investigated materials, TiO₂/AC = 4:1 achieved the highest photocatalytic activity with a high k of 55.2×10^-3 min^-1 and an MB removal efficiency of 96.6% after 30 min treatment under UV-Vis irradiation (120 mW/cm²). The enhanced photocatalytic activity for TiO₂/AC is due to the synergistic effect of the high adsorption capability of AC and the high photocatalytic activity of TiO₂. Furthermore, TiO₂/AC promotes the separation of photoexcited electron/hole (e^-/h⁺) pairs to reduce their recombination rate and thus enhance photocatalytic activity. The optimal TiO₂/AC composite in this study can be used for treating industrial or household wastewater with organic pollutants.

In recent years, the rapid development of computer-aided planning and design technology has provided a new perspective for the study of complex problems such as the generation of architectural complex forms. This study focuses on how to apply parameterization technology to analyze and articulate traditional spatial form composition rules, aiming to minimize reliance on subjective human judgment in the protection and renewal design of the historical style of traditional villages. It aims to establish digital generative design tools to address the challenges of accurately inheriting and innovatively utilizing historical and cultural information in traditional settlements. It introduces how to rely on parameterization technology to analyze the spatial form composition rules, parameter extraction rules, and spatial reconstruction rules of traditional villages, facilitating the complete process from spatial features to parameterization rules, and then to the application of computational methods to deduce spatial features. It also includes case studies demonstrating the application of parameterization technology tools for village protection and explores the role of generative design tools in preserving the spatial style of these settlements.

We show that combining vibrational spectroscopy with signal processing can result in a scheme for ultrasensitive detection of molecules. We consider the vibrational spectrum as a signal on the energy axis and apply a matched filter on that axis. On the example of a nerve agent molecule, we show that this allows detecting a molecule by its vibrational spectrum even when the recorded spectrum is completely buried in noise, when conventional spectroscopic detection is impossible. Detection is predicted to be possible with signal-to-noise ratios in recorded spectra as low as 0.1. We study the importance of spectral range used for detection as well as of the quality of the computed spectrum used to program the filter, specifically, the role of anharmonicity, of the exchange correlation functional, and of the basis set. The use of the full spectral range rather than of a narrow spectral window with key vibrations is shown to be advantageous, as well as accounting for anharmonicity.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

As the embedded device and internet of things (IoTs) concept prevalent in today's world, there is an increasing demand for the security and performance requirements on deploying these devices to private and public sectors. The crucial part of it is to protect privacy, confidentiality and integrity, meanwhile, maintain an adequate level of performance during transmission, storage and access of critical information. While the conventional cryptography methods, such as the Advanced Encryption Standard (AES), SHA$-$2 hashing method and RSA and Diffie Hellman for message authentication and identification, work well on systems which have reasonable processing power and memory capabilities. These do not scale well into a world with embedded systems and sensor networks, in conjunction with their nature of smaller size and lower cost. Thus, in the context of resource constrained device, lightweight cryptography methods are proposed to overcome many of the problems of conventional cryptography possessed. This includes constraints related to physical size, processing requirement, memory limitation, energy drain and production cost. This paper provides a survey of the architectures that are defined as replacements for conventional ciphers within an IoTs space and discuss some trends in the design of future lightweight algorithms. The performance metrics are carefully chosen to reflect and assess the suitability for embedded devices. The aim of this research is to identify the various performance metrics applied on different types of symmetric block ciphers especially lightweight ciphers and compare the results on versatile platforms with stream ciphers and public key methods. The comparative analysis on efficient LW cipher will be tested against other similar block ciphers on both MacBook Pro with Intel core and resource constrained device Raspberry Pi with ARM processor.

Purpose: To clarify the mechanism of state anxiety on intertemporal decision-making, two studies were conducted to investigate the role of trait anxiety and inhibitory control. Study 1 examined the moderating effect of trait anxiety. Study 2 continued to investigate the mediating effect of inhibition control on the basis of study 1. Methods: A total of 266 Chinese college students participated. Participants’ state anxiety, trait anxiety and intertemporal decision-making were measured by questionnaires (scales) respectively. And inhibition control was evaluated by two-choice oddball paradigm. Results: The results of Study 1 indicated that state anxiety could predict intertemporal decision-making and that the moderating effect of trait anxiety on this relationship was significant. Study 2 found that inhibitory control could completely moderate the relationship between state anxiety and intertemporal decision-making and that this indirect effect was affected by trait anxiety. Conclusion: 1)Individuals with higher trait anxiety are more inclined to make more impulsive and intertemporal decisions when they have a high level of state anxiety; 2)state anxiety allows inhibitory control ability to have a further effect on intertemporal decision-making; and 3)the higher trait anxiety in individuals, the stronger mediating effect of inhibitory control on the relationship between state anxiety and intertemporal decision-making.

Knee osteoarthritis is the most popular type of osteoarthritis that causes extreme pain in elderly. Currently there is no cure for osteoarthritis. To lessen clinical symptoms, glucosamine was suggested. The primary goal of our study is to evaluate the efficacy and safety of glucosamine from recent studies. Electronic databases such as PubMed, Scopus, Cochrane were used to assess RCT. From the beginning through March 2023, the papers were checked, and if they fulfilled the inclusion criteria, they were then examined. WOMAC and VAS scales were considered as main outcome measure. A total of 15 studies were selected. Global pain was significantly decreased in comparison to placebo, as measured by the VAS index, with an overall effect size SMD of -7.41 ([95% CI] 14.31, 0.51). The WOMAC scale confirmed that pain, stiffness, and physical function had improved, however the effects were insufficient. A statistical update also revealed that there were no reports of serious medication interactions or significant adverse events. To summarize, glucosamine is more effective than a placebo at reducing pain in knee osteoarthritis patients. In long-term treatment, oral glucosamine sulfate 1500 mg/day is believed to be well tolerated.

Xinjiang, as a climate-sensitive region in northwest China, holds significant importance in studying extreme weather events for agricultural production and socioeconomic development. Based on data from 52 meteorological stations and 23 extreme climate indicators in Xinjiang from 1960 to 2021, the 5a moving average, linear trend estimation, climate tendency rate, and GIS spatial analysis methods are used to analyze the distribution and change characteristics of extreme climate. The results revealed that from 1960 to 2021, TXx, TNx, TXn, TNn, FD, ID, TN10p, TX10p, and WSDI showed a significant upward trend, while SU, TR, TN90p, TX90p, and CSDI showed a significant downward trend. What is more, the range of changes in the extreme temperature indexes from 1990 to 2021 is higher than that of 1960 to 1989. The high-value areas of extreme indexes are primarily concentrated in the northern part, while the high-value areas of cold event indexes are mainly distributed in the southern part. The upward/downward trends all accounting for over 80.00% of the entire region. The Rx1day, Rx5day, PRCPTOT, R95p, R99p, R10, R20, and R25 showed a significant growth trend from 1960 to 2021, and the range of change in the extreme precipitation indexes from 1990 to 2021 was lower than that from 1960 to 1989. Moreover, their high-value areas and high climate tendency areas are mainly concentrated in the northern and western parts of Xinjiang, with upward trends all accounting for over 71.00% of the entire region. The research results provide theoretical foundations for formulating climate risk strategies in the northwest region of China.

The TiO₂ nanostructures resulted by pyrolysis of TiCl₄ at low temperature of 80 ^oC are found to be a mixture of amorphous TiO₂ complexes and anatase nanostructure whose ratio depends on the pH of the pyrolysis medium. At low pH level, the resulting TiO₂ nanostructure is predominant anatase and gradually shifts to the amorphous TiO₂ complexes with pH level increasing. By means of heat treatment, the amorphous TiO₂ complexes can be converted back to the anatase nanostructure and then transform to rutile with the elevating temperature. Amongst of the TiO₂ nanostructure recovered from amorphous TiO₂ complexes, the anatase shows to be the most effective photocatalyst in decomposition of methylene blue.

Porous tantalum (Ta) is a promising biomaterial and has been applied in orthopedics and dentistry for nearly two decades. The high porosity and interconnected pore structure of porous Ta promise fine bone ingrowth and new bone formation within the inner space, which further guarantee rapid osteointegration and bone-implant stability in long term. Porous Ta has high wettability and surface energy that can facilitate adherence, proliferation and mineralization of osteoblasts. Meanwhile, low elastic modulus and high friction coefficient of porous Ta can effectively avoid stress shield effect, minimize marginal bone loss and ensure primary stability. Accordingly, the satisfactory clinical application of porous Ta based implants or prostheses are mainly derived from its excellent biological and mechanical properties. With the advent of additive manufacturing, personalized porous Ta based implants or prostheses have shown their clinical value in the treatment of individual patient who need specially designed implant or prosthesis. In addition, many modification methods have been introduced to enhance the bioactivity and antibacterial property of porous Ta with promising in vitro and in vivo research results. In any case, choosing suitable patients is of great importance to guarantee surgical success after porous Ta insertion.

Head and neck squamous cell carcinoma (HNSCC) is a type of cancer that arises from the epithelium lining of the oral cavity, hypopharynx, oropharynx, and larynx. Despite advancement of the current treatment to HNSCC, such as surgery, chemotherapy, and radiotherapy, the overall survival rate of HNSCC remains poor due to late diagnosis and acquired resistance to treatment. Natural products have been extensively explored as a safer and more acceptable alternative to current treatments, with numerous studies displaying their potential against HNSCC. This review highlights preclinical studies in the past 5 years involving natural products against HNSCC and explores the signalling pathways altered by these products. This review also addresses challenges and future directions of the use of natural products as chemotherapeutic and chemoprevention agents against HNSCC.

As a renewable industrial crop, Miscanthus offers numerous advantages, namely high photosynthesis activity (as a C4 plant) and exceptional CO2 fixation rate. These properties make Miscanthus very attractive for industrial exploitation, such as lignin generation. Here, we present a systematic study analyzing the correlation of the lignin structure with Miscanthus genotype and plant portion (stem versus leaf). Specifically, the ratio of the three monolignols and corresponding building blocks as well as the linkages formed between the units have been studied. Depending on the Miscanthus genotype and plant component (leaf versus stem), correlations between chemical structure and properties of the lignins have been determined, i.e. correlations in molecular weight, polydispersity and decomposition temperature. Lignin isolation was performed using non-catalyzed organosolv pulping and the structure analysis includes NREL, FTIR, UV-Vis, HSQC-NMR, TGA, pyrolysis GC/MS. Structural differences were found for stem and leaf-derived lignins. Compared to beech wood lignins, Miscanthus lignins possess lower molecular weight and narrow polydispersities (< 1.5 Miscanthus vs. > 2.5 beech) corresponding to improved homogeneity. In addition to conventional univariate analysis of FTIR spectra, multivariate chemometrics revealed distinct differences for aromatic in-plane deformations of stem versus leaf-derived lignins. These results emphasize the potential of Miscanthus as low-input resource and Miscanthus-derived lignin as promising agricultural feedstock.

Aim at a better understanding of the flow field around a fully appended Joubert BB2 submarine model and complementing the experimental investigations of the wake of the hydroplanes and sail, the Large eddy simulation (LES) with the dynamic Smagorinsky model is conducted. Three sets of grids with a maximum grid number of up to 228 million are designed, to perform the LES simulation for the Joubert BB2 at 10° yaw conditions, with a freestream Reynolds (Re) number based on the local freestream velocity and the hull length of ReL=2.2×107. And comparison of the wake of the cruciform appendage is made with experiments, to verify the computational accuracy and examine the influence of the spatial resolution. A satisfactory result shows more favorable agreement with experimental measurements as the improvement of spatial resolution, with the relative error of the vortice centers well within 7.2% in the most refined grid arrangement. And under this grid arrangement, the evolution characteristics of three co-rotating vortices originating from the cruciform appendage are further described in detail at straight ahead and 10° yaw conditions.

The current study aimed to investigate the relationship between physical activity (PA) level and inhibitory control performance and then determine whether this association was mediated by multiple sleep parameters (i.e., subjective sleep quality, sleep duration, sleep efficiency, sleep disturbance). Methods. 180 healthy university students (age: 20.15 ± 1.92 years) from the East China Normal University were recruited in the present study. PA level, sleep parameters, and inhibitory control performance were assessed using the International Physical Activity Questionnaire (IPAQ), the Pittsburgh Sleep Quality Index Scale (PSQI), and a Stroop test, respectively. Data were analyzed using structual equation modeling. Results. A higher level of PA was linked to better cognitive performance. Furthermore, higher subjective sleep quality and sleep efficiency were associated with better inhibitory control performance. The mediation analysis revealed that subjective sleep quality and sleep efficiency mediated the relationship between PA level and inhibitory control performance. Conclusion. Our results are in accordance with the literature and buttress the idea that a healthy lifestyle that involves a relatively high level of regular PA and adequate sleep patterns is beneficial for cognition (e.g., inhibitory control performance). Furthermore, our study adds to the literature that sleep quality and sleep efficiency mediates the relationship of PA and inhibitory control performance expanding our knowledge in the field of exercise-cognition.

Objective: To study the factors affecting the time of umbilical cord shedding in premature infants.Methods: A total of 151 premature infants who were born in the obstetrics department of a Class III hospital in Hefei from November 2020 to June 2021 were selected as subjects. All premature infants and their families met the complete inclusion criteria. A total of 33 related factors from 3 aspects, including the birth situation of premature infants, the condition of premature infants in hospital and the condition of pregnant mothers, were collected for univariate analysis and multiple Logistic regression analysis. The relevant factors affecting the umbilical cord shedding time of premature infants were screened through the univariate analysis results, and the main factors affecting the umbilical cord shedding time of premature infants were screened through the multiple Logistic regression analysis results.it was found that the weight, gestural age, admission age, whether the premature infants were combined with NRDS, the use of antibiotics, the duration in the warm box, the initial temperature in the warm box, the duration of light therapy, the degree of Apgar for 1 minute, the maternal education level had an effect on the time of umbilical cord shedding of premature infants (P < 0.05). Through Logistic multiple regression analysis, it was screened that the duration of premature infants in the incubator was the main factor affecting the umbilical cord shedding time of premature infants (P < 0.05).Conclusion: Factors such as premature infants' weight, gestural age, admission age, whether they are combined with NRDS, antibiotic use, duration in the incubator, initial temperature in the incubator, duration of phototherapy, Apgar level of 1 minute, and maternal education level will affect the umbilical cord shedding time of premature infants. Among them, duration in the incubator is the main factor affecting the umbilical cord shedding time of premature infants.

Sensory descriptive analysis was used to evaluate the aged Feng-flavored baijiu. The results indicated that there are notable differences in the samples of different ages. The samples with shorter storage times and fresh distilled Baijiu present bran flavor, and fresh green flavor. with the increase of storage time, the fragrance of honey, sweetness, flowers, and aging gradually increases. The samples of Feng-flavored baijiu were dected by Headspace solid-phase microextraction (HS-SPME) combined with comprehensive two-dimensional gas chromatography time-of-flight mass spectrometry (GC×GC–TOFMS) , in total, 496 sustances were identified in all samples, mainly containing 14 types of substances, such as esters, aldehydes etc., of which 42 substances were found in Feng-flavored baijiu for the first time. Chemometrics was used to analyze the key differential compounds. 143 differential compounds closely related to aging were preliminarily screened, and principal component analysis revealed that these samples were separated by year. 65 differential compounds were selected out by partial least squares discriminant analysis(PLS-DA). Furthermore, 43 key differential compounds were selected from the aged Feng-flavored baijiu combined with variable importance in projection and Pearson correlation coefficients. Partial least squares regression (PLSR) was used to research the correlation of sensory properties and key differential compounds, and the results indicated that most compounds were closely related to the aged Baijiu . This study afford theoretical basis and reference for flavor research of Feng-flavored baijiu.

The antiradical and antimicrobial activity of lignin and lignin-based films are both of great interest for applications such as food packaging additives. The polyphenol structure of lignin in addition to the presence of O-containing functional groups is potentially responsible for these activities. This study used DPPH assays to discuss the antiradical activity of HPMC/lignin and HPMC/lignin/chitosan films. The scavenging activity (SA) of both binary (HPMC/lignin) and ternary (HPMC/lignin/chitosan) systems was affected by the percentage of the added lignin: the 5% addition showed the highest activity and the 30% addition had the lowest. Both, scavenging activity and antimicrobial activity are depending on the biomass source showing the following trend: organosolv of softwood > Kraft of softwood > organosolv of grass. Testing the antimicrobial activities of lignins and lignin-containing films showed high antimicrobial activities against gram-positive and gram-negative bacteria at 35 °C and at low temperatures (0-7 °C). Purification of kraft lignin has a negative effect on the antimicrobial activity while storage has positive effect. The lignin release in the produced films affected the activity positively and the chitosan addition enhances the activity even more for both gram-positive and gram-negative bacteria. Testing the films against spoilage bacteria that grow at low temperatures revealed the activity of the 30% addition on HPMC/L1 film against both B. thermosphacta and P. fluorescens while L5 was active only against B. thermosphacta. In HPMC/lignin/chitosan films the 5% addition exhibited activity against both B. thermosphacta and P. fluorescens.

The COVID-19 pandemic has expanded globally and caused serious consequence in both health system and the economy. MPV is one of two oral antivirals for COVID-19 with mild-to-moderate symptoms that have received FDA approval so far. This study aims to evaluate the cost-utility of using MPV in COVID-19 treatment. To compare the utility costs of MPV and non-MPV treatments for COVID-19 patients, we used a decision tree model. Data on clinical efficacy, cost, and quality of life were gathered from previous studies. The incremental effective cost ratio (ICER) calculated based on costs incurred and quality-adjusted life years (QALY), was considered as primary out-come. The total cost of MPV treatment and not using MPV was 15,362,516 VND (618 USD) and 15,771,262 VND (634 USD), respectively. The estimated QALY with using-MPV was 28.33, while without MPV was 19.72. The ICER was dominant, resulting in savings of 47,453 VND/QALY (1.9 USD). MPV is a cost-effective medication used to treat COVID-19. In mild-to-moderate COVID-19 patients, MPV considerably lowers costs and improves quality of life. However, several clinical factors of the drug still need to be taken into account.

SARS-CoV2 (corona virus) has spread globally at an unprecedented rate; so far, increasing SARS-CoV2-infected individuals have been identified. Although the situation in China is improving and is currently under control, the outbreak in other countries and its pandemic management is only beginning to develop. Based on 154 SARS-CoV2 genome sequence analyses, we used receptor–ligand docking to identify one potential point mutation (V354F) on the spike structure which enhances spike binding to ACE2 receptors underlying potential super infection. Importantly, the V354F site on spike S1 had been identified in 5/10 infected French patients living in Paris, who sharing 100% identical SARS-CoV2 genomes. With Covid-19 cases increasing rapidly in France that could lead to a new explosion, we suggest that the French government should identify all potential super spreaders and treat them accordingly. In summary, our study provides on of the measures to avoid the potential second worldwide explosion of SARS-CoV2.

In this study, we demonstrate a high luminous efficacy of 118 lm/W and high reliability through 450°C thermal aging of white LEDs (WLEDs) utilizing four-inch YAG: Ce3+ phosphor-in-glass (PiG) plates designed for vehicle headlights. The sintering process of mixing glass and phosphor typically generates pores, which can scatter light and reduce the luminous efficacy of the fabricated PiG. In this study, we produced four-inch PiG plates under four different fabrication conditions to evaluate their luminous efficacy. Our results revealed that the PiG plate with a thin thickness of 0.08 mm exhibited a 16.83% increase in luminous efficacy compared to the 0.15 mm plate, attributed to reduced light interaction with the pores. Unlike silicone-based phosphor WLEDs, which offer high performance but lower reliability due to the silicone resin's low transition temperature (150°C), our novel thin PiG plate achieves high performance and reliability. This advancement suggests that the proposed thin PiG plate could replace traditional silicone-based phosphors, enabling the development of high-quality WLEDs for vehicle headlights in automotive applications.

Food waste is a common issue arising from grinding of food by experimental animals, leading to excessive food scraps falling into cages. In the wild, animals grind food by gnawing vegetation and seeds, potentially damaging the ecological environment. However, limited ecology studies have focused on food grinding behavior since the last century, with even fewer on rodent food grinding, particularly recently. Although food grinding function is partially understood, biological purposes remain under-investigated and driving factors unclear. This review aims to explain potential causes of animal food grinding, identify influencing factors, and discuss contexts and limitations. Specifically, we emphasize recent progress on gut microbiota significance for food grinding. Moreover, we show abnormal food grinding is determined by degree of excess normal behavior, emphasizing food grinding is not meaningless. Findings from this review promote comprehensive research on the myriad factors, multifaceted roles, and intricate evolution underlying food grinding behavior, benefiting laboratory animal husbandry and ecological environment protection, and identifying potential physiological benefits yet undiscovered.

This study assesses the biomethane (CH4) generation and greenhouse gas (GHG) emissions resulting from municipal solid waste landfilling in Phnom Penh, Cambodia, with a focus on the impact of fugitive CH4 emissions and operation processes in four landfilling scenarios: simple dumping (S1), improved management with leachate treatment (S2), engineered landfill with flaring (S3), and engineered landfill with energy recovery (S4). The study also considered the environmental benefits of carbon sequestration and landfill gas utilization. The LandGEM and IPCC FOD models were used to calculate CH4 generation over the period of 2009-2022, and it was found that approximately 18 and 21 M kg/year of CH4 are released, respectively. The energy potential from CH4 recovery was 51–61 GWh/year. Overall GHG emissions in S2 were the highest, amounting to 409–509 M kg CO2-eq/year, while S1 had lower emissions at 397–496 M kg CO2-eq/year. Flaring captured CH4 in S3 could reduce GHG emissions by at least 55%, and using captured CH4 for electricity production in S4 could mitigate at least 83% of GHG emissions. Electricity recovery (S4) could avoid significant amounts of GHG emissions (˗104.5 kg CO2-eq/tMSW). The study suggests that landfill gas-to-energy could significantly reduce GHG emissions.

Arthropods, the most abundant group in ecosystems, play crucial roles in human production. Soil physicochemical properties reflect soil health and are linked to arthropods through cascading effects. Gravel-sand mulching, commonly practiced in dry farming regions, initially aids in water retention and temperature regulation. However, long-term cultivation can lead to land degradation and habitat fragmentation. This study aimed to investigate field systems using multiple comparison, linear, and nonlinear correlation analyses to explore the effects of different tillage durations on soil properties and arthropod diversity under gravel-sand mulching. Results indicate that arthro-pod diversity was lower while the fields maintained better soil fertility than the desert steppe. Both soil fertility and arthropod diversity declined significantly with increased years of cultivation. Mantel tests revealed no significant response of desert steppe arthropods to the altered soil properties of gravel-sand mulched fields. However, the Generalized Additive Model analysis indicated significant linear correlations between arthropod occurrence and total nitrogen (positive), available phosphorus, and water content (negative). Arthropod abundance showed significant nonlinear correlations with total potassium, alkali hydrolyzable nitrogen, and organic matter (OM), with OM changes having the most pronounced impact. Thus, gravel-sand mulching can maintain soil fertility over time but at the expense of local arthropod diversity.

This study aimed to identify sociodemographic and health indicators of diet quality in pre-frail community-dwelling older adults. Pre-frail older adults are those at risk of progression to clinical manifestations of frailty and are targets for preventative intervention. We previously reported that pre-frail older adults have reasonably good overall diet quality. However, further analyses found low intake of energy, protein and several micronutrients. Methods: We collected detailed dietary intake from pre-frail (FRAIL scale 1-2) older adults using NZ Intake24, an online version of 24-hour multiple pass dietary recall. Diet quality was ascertained with the Diet Quality Index-International (DQI-I). We used regression Generalised Linear Models to determine predictors of diet quality and Classification and Regression Tree (CART) analysis to examine the complex relationships of predictors and identified profiles of sub-groups of older adults that predict diet quality. Results. The median age in this sample (n=468) was 80.0 years (77.0-84.0). Living with others, high deprivation index and a higher BMI were independent predictors of poorer diet quality. With CART analysis, we found that those with a BMI &gt;29 kg/m2, living with others and younger than 80 years were likely to have a lower diet quality. Conclusions: We found BMI, living arrangement and socioeconomic status were independent predictors of diet quality in pre-frail older adults, with BMI being the most important variable in this sample when the interacting relationships of these variables were considered. Future research is needed to determine the similarities and/or differences in the profile of subgroups of older adults with poorer diet quality.

In this article, we present the use of the coupled land surface model and groundwater flow model SWAT-MODFLOW with the decision support tool WEAP (Water Evaluation and Planning software) to predict future surface water abstraction scenarios in a complex river basin, under conditions of climate change. The modeling framework is applied to the Dee River catchment in Wales, United Kingdom. Regarding hydrology, the coupled model improves overall water balance and low streamflow conditions, compared to a stand-alone SWAT model. The calibrated SWAT-MODFLOW is employed with high resolution climate model data from the UKCP18 project with future scenario of RCP85 from 2020 to 2040. Then, water supply results from SWAT-MODFLOW are fed into WEAP as input for the river reach in the downstream region of the river basin. This system is utilized to create various future scenarios of surface water abstraction of public water supply in the downstream region: maximum licensed withdraw, 50 % authorized abstractions, monthly time series with 1% increase of water use, and maximum water withdraw year based on historical records repeated every year with 1% increase of water use, to estimate the unmet demands and streamflow requirement. This modeling approach can be used in other river basins to manage scenarios of supply and demand.

Robotic path planning is a field of research which is gaining traction given the broad domains of interest to which path planning is an important systemic requirement; the aim being to optimise the efficacy of robotic movements in a defined operational environment. For example, robots have been employed in many domains including: cleaning robots (such as vacuum cleaners), automated paint spraying robots, window cleaning robots, forest monitoring robots, agricultural robots (often driven using satellite and geostationary positional satellite data). Additionally, mobile robotic systems have been utilised in disaster areas and locations hazardous to humans (such as war zones in mine clearance). The coverage path planning problem describes an approach which is designed to determine the path that traverses all points in a defined operational environment while avoiding static and dynamic (moving) obstacles. In this paper we present our proposed Smooth-STC model, the aim of the model being to identify an optimal path, avoid all obstacles, prevent (or at least minimise) backtracking, and maximise the coverage in any defined operational environment. The experimental results in a simulation show that, in uncertain environments, our proposed smooth STC method achieves an almost absolute coverage rate and demonstrates improvement when measured against alternative conventional algorithms.

To explore the effects of pymetrozine on the reproductive behavior of N. lugens, we established a bioassay method to accurately evaluate the toxicity of pymetrozine in N. lugens and establish the level of pymetrozine resistance of N. lugens in the field. In this study, pymetrozine’s effects on the fecundity of N. lugens were evaluated using the topical application method and rice-seedling dipping method. Moreover, the resistance of N. lugens to pymetrozine in a pymetrozine-resistant strain (Pym-R) and two field populations (YZ21 and QS21) was determined using the rice-seedling dipping method and fecundity assay methods. The results showed that treatment of N. lugens third-instar nymphs with LC15, LC50, and LC85 doses of pymetrozine resulted in significantly reduced male fertility and female fecundity. In addition, N. lugens adults treated with pymetrozine using the rice-seedling dipping and topical application method also exhibited significantly in-hibited male courtship, fertility, and female receptivity. Using the rice-stem dipping method, pymetrozine resistance was shown to be at high levels in Pym-R (194.6-fold), YZ21 (205.9-fold), and QS21 (212.8-fold), with LC50 values of 522.520 mg/L (Pym-R), 552.962 mg/L (YZ21), and 571.315 (QS21) mg/L. However, when using the rice-seedling dipping or topical application fe-cundity assay method, Pym-R (EC50: 14.370 mg/L, RR=12.4-fold; ED50: 0.560 ng/adult, RR=10.8-fold), YZ21 (EC50: 12.890 mg/L, RR=11.2-fold; ED50: 0.280 ng/adult; RR=5.4-fold), and QS21 (EC50: 13.70 mg/L, RR=11.9-fold) exhibited moderate or low levels of resistance to pymet-rozine. Our studies show that pymetrozine can significantly inhibit the fecundity of N. lugens. The fecundity assay results showed that N. lugens only developed low to moderate levels of resistance to pymetrozine, indicating that pymetrozine can still achieve effective control on the next gen-eration of N. lugens populations.

Background. There is limited evidence on the relationship between chronic kidney disease (CKD) and frailty in older people in Vietnam. This study aimed to examine the prevalence of frailty and its impact on mortality in older patients with end-stage renal disease. Method. This is a prospective, observational study at two large Dialysis Centres in Vietnam from November 2020 to June 2021. Consecutive older patients diagnosed with end-stage renal disease and on dialysis were recruited. Participants’ frailty status was defined by the Clinical Frailty Scale (CFS). The study outcome was all-cause mortality at 6th month. Results. A total of 175 participants were recruited (mean age 72.4 years, 58.9% female). Using the cut-point of CFS ≥4, 87.4% of the participants were frail. Mortality at 6th month was 14.9%, 31.9% in participants with CFS ≥7, 12.8% in participants with CFS=6, 7.5% in participants with CFS from 4 to 5, and 4.5% in participants with CFS ≤3 (p=0.001). Cox regression analysis showed that compared to the non-frail participants, the probability of death over 6 months was nearly 2-fold higher in the mildly frail, 3-fold higher in the moderately frail, and 9-fold higher in the severely frail participants. Conclusion. This study demonstrated a very high prevalence of frailty in older patients with end-stage renal disease and dialysis and the significant impact of frailty severity on mortality. Healthcare providers should consider incorporating frailty screening into routine care for older patients with end-stage renal disease and dialysis.

The reliance on cloud computing services and related technologies has increased due to their many benefits, including resource sharing and the need for organizations to maintain their competitive advantage in the digital market. Also, the pace of cloud growth has significantly increased because of COVID-19. Many companies and businesses have shifted their core processes to the cloud for seamless operations during the pandemic. This migration of legacy systems to the cloud creates many opportunities for businesses. However, on the other hand, it may also bring substantial challenges. Hence, a careful decision is needed to align with company goals. In this paper, we demonstrate the need and advantages of cloud computing, followed by highlighting AWS's characteristics as one of the leading cloud service providers. We also discuss the merger of AWS with SDN to improve cloud data security and performance. The outcomes of this study can provide a data migration strategy and guide decision-makers toward a secure and sustainable migration to a cloud computing environment.

Rapid urbanization has dramatically spurred the economic development over the past three decades, especially in China, but has nevertheless had negative impacts on natural resources since it is an irreversible process. Thus, it is essential to timely monitor and quantitatively analysis the changes in land use over time and to identify the landscape pattern variation related to growth mode in different period. This study aims at inspecting spatiotemporal characteristics of landscape pattern respond to land use changes in Xuzhou city during the period from 1985 to 2015. In this connection, we proposed a new spectral index, named the Normalized Difference Enhanced Urban Index (NDEUI), which combines data from NTL (Nighttime light) from the Defense Meteorological Satellite Program/Operational Linescan System (DMSP/OLS) with annual maximum Enhanced Vegetation Index (EVI) to reduce the detection confusion between urban areas and barren land, as well as follows. NDEUI-assisted Random Forests algorithm was implemented to obtain the land use/land cover (LULC) maps of Xuzhou in 1985, 1995, 2005 and 2015, respectively. Here, four different periods viz. 1985–1995, 1995–2005, 2005–2015 and 1985–2015 are chosen for the change analysis of land use and landscape pattern. The results indicated that the urban area has increased by about 30.65%, 10.54%, 68.77%, and 143.75% during the four periods mentioned above at the main expense of agricultural land, respectively. The spatial trend maps revealed that continuous transition from other land use types into urban land has appeared a dual-core development mode throughout the urbanization process, located at the new city region and the Jiawang district, mainly affected by the construction of new city region, freeway and the high railway station. Furthermore, we quantified the patch complexity, aggregation, connectivity and diversity of landscape employing a number of landscape metrics to represent the changes of landscape pattern at both class and landscape level, affected by urbanization during the study period. The results showed that with regard to the four aspects of landscape pattern, there were considerable differences among the four years, mainly owing to the increasing dominance of urbanized land. Spatiotemporal variation of landscape pattern was also conducted on the basis of subgrids in 900 m × 900 m. Combined with the land use changes and spatiotemporal variation of landscape pattern, it can be concluded that different urbanization modes and intensity result in variously the spatiotemporal evolution of landscape patterns. For Xuzhou city, the urban growth mainly appeared a leapfrog mode alone both sides of the roads during the period of 1985 to 1995, and then shifted into edge-expansion mode during the period from 1995 to 2005, whereas the edge-expansion and leapfrog modes coexisted for the period from 2005 to 2015. The high valuable spatiotemporal information generated utilizing RS and GIS in this study may give assistance to urban planners and policymakers to well understand urban dynamics and evaluate their spatiotemporal and environmental impacts at a local level for the sake of sustainable urban planning in the future.

In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

The Vu Gia - Thu Bon River Basin (VG-TB) is confronting numerous challenges related to water security (WS), particularly in the face of the impacts of climate change. These challenges manifest in salinity intrusion, altered rainfall patterns, and reduced water supply in downstream areas. To assess the current state of water security in the basin, the study employed statistical analysis methods, Process Analysis Method (PAM), SMART, and Analytic Hierarchy Process (AHP) to develop a comprehensive Assessment Framework for Water Security (AFWS) in the VG-TB. The AFWS encompasses five key dimensions, 17 indicators, and 28 variables, aligning with the UN-Water definition of water security and addressing the Sustainable Development Goal 6 (SDG6) criteria for global water sustainability. It also adheres to the Asian Development Bank's (ADB) approach to water security assessment as outlined in the Asian Water Development Outlook (AWDO) reports. This allows for the computation of a comprehensive Water Security Index (WSI) for specific regions, serving as a foundation for decision-making and policy formulation aimed at enhancing water security in the context of climate change and facilitating sustainable basin development in the future.

In view of the fact that the field monitoring information can more intuitively and accurately reflect the stability state of slopes, this paper takes the warning threshold of slope deformation rate monitoring as the slope stability evaluation standard, and puts forward a method for solving the safety coefficient of rocky slopes. The discrete element method 3DEC, which is suitable for rocky slopes, is selected as the numerical calculation tool, and the convergence criterion of its strength reduction method is modified to the slope deformation rate threshold, and the method is realized by the bifurcation method through its built-in FISH programming language. The results of the classical case show that, by selecting the slope deformation rate threshold in the appropriate interval, the results of this paper's method are very close to those of the finite unit stress method and the limit equilibrium method, which verifies the reliability of this paper's method. Further, the method of this paper is applied to an open-pit mine slope project, based on the slope deformation on-site monitoring data, through the time series prediction method to determine the slope deformation rate warning threshold, using the threshold as an evaluation criterion to solve the slope's coefficient of safety, the calculation results show that: the slope's coefficient of safety in natural working conditions is 1.086, basically stable, suffered from continuous rainfall, the slope body is gradually saturated, the slope's coefficient of safety is reduced to 0.987, the slope's safety is reduced to 0.987. After continuous rainfall and gradual saturation of the slope, the coefficient of safety decreased to 0.987, destabilizing and destroying, which is consistent with the site conditions.

A novel five-surface phosphor-in-glass (FS-PiG) for high illumination and excellent color uniformity in larger-scale LEDs for sensor light source application is demonstrated. YAG phosphor (Y3Al5O12:Ce3+) was uniformly mixed with ceramic and sintered at 680°C to form a phosphor wafer. A sophisticated laser engraving was employed on the phosphor wafer to form a saddle-shaped large-scale FS-PiG LEDs. The performance of the FS-PiG LEDs exhibited the illumination of 401lm, average color temperature (CCT) of 5488K±110K, and color coordinates (CIE) of (0.3179±0.003, 0.3352±0.003). In contrast to convention single-surface phosphor-in-glass (SS-PiG) LEDs, the performance exhibited the illumination of 380lm, average CCT of 5830K±758K, and CIE of (0.3083±0.07, 0.3172±0.07). These indicated that the performance of the FS-PiG LEDs was higher than the SS-PiG LEDs for illumination, CCT, and CIE of 1.7, 7, and 23 times, respectively. Furthermore, the FS-PiG LEDs demonstrate lower lumen loss of 2% and less chromaticity shift of 5.4x10-3 under accelerated aging at 350°C for 1008 hours, owing to the high ceramic melting temperature of up to 510°C. In this study, the proposed FS-PiG larger-scale LEDs having excellent optical performance and high reliability may be the promising candidates to replace the convention phosphor-in-organic silicone material used in high-power LEDs for the next generation of sensor light sources, display, and headlight applications.

Nowadays, with smartphones people can easily take photos, post photos to any social networks and use the photos for some purposes. This leads to a social problem that unintended appearance in photos may threaten the privacy of photographed person. Some solutions to protect facial privacy in photos have already been proposed. However, most of them rely on different techniques to de-identify photos which can be done only by photographers, giving no choice to photographed person. To deal with that, we propose an approach that allows photographed person to proactively detect whether someone is intentionally/unintentionally trying to take pictures of him/her. Thereby, he/she can have appropriate reaction to protect the privacy. In this approach, we assume that the photographed person uses a wearable camera to record the surrounding environment in real-time. The skeleton information of likely photographers who are captured in the monitoring video is then extracted to be put into the calculation of dynamic programming score which is eventually compared with a threshold for recognition of photo-taking behavior. Experimental results demonstrate that by using the proposed approach, the photo-taking behavior is precisely recognized with high accuracy of 92.5%.

This literature review paper delves into the synergies between Climate-Smart Agriculture (CSA) and the effective management of food losses. With the escalating challenges posed by climate change and the pressing need to address food security concerns, the intersection of these two critical domains becomes paramount for sustainable agricultural practices. The review explores existing research on the implementation of climate-smart agricultural techniques and their impact on mitigating food losses throughout the agricultural value chain. The paper synthesizes findings related to climate-resilient crop varieties, precision farming, water-use efficiency, and sustainable soil management, highlighting their contributions to reducing post-harvest losses and enhancing overall food security. In addition to summarizing current knowledge, this paper identifies gaps in the literature and proposes avenues for future research. This review serves as a foundation for researchers, policymakers, and practitioners seeking to contribute to the advancement of climate-smart agriculture and the reduction of food losses, paving the way for a more sustainable and resilient global food system.

Halide perovskite materials gain enormous attention for their semiconducting properties, higher power conversion efficiency and potential applications in a wide range field of studies along with their two key limitations: stability and toxicity. In spite of great progress made on the halide perovskites and many promising research developments, overcoming these limitations is not realized yet. Therefore, coordination engineering of new framework for obtaining alternative new halide perovskite materials and fundamental understanding of the coordination chemistry and electronic interactions forming the structure of these newly engineered halide perovskite materials might be one way in order to overcome the issues related to both stability and toxicity. In this review, the current development of halide perovskite families, both lead halide perovskites and lead free halide perovskites followed by coordination engineering of the new frameworks to engineer new halide perovskite materials will be reviewed comprehensively. Moreover, all the concerns of the fundamental ideas of coordination chemistry and electronic interactions that are keys in forming the halide perovskite structures are discussed in detail and form the main aim of this review. Interestingly, we also discuss recent potential energy applications beyond photovoltaic and this review has completed with an essential and open question: ‘what could happen in the future of halide perovskites?’ in order to excite commercial enterprises and research institutions again as well as to get motivating new predictions on the future continuity of this field.

With the introduction of HTTP/3, whose transport is no longer the traditional TCP protocol but the novel QUIC protocol, research for solutions to the unfairness of Adaptive Streaming over HTTP (HAS) has become more challenging. That is, because of different transport layers, the HTTP/3 may not be available for some networks and the clients have to use HTTP/2 for their HAS applications instead. Therefore, the scenario that HAS over HTTP/3 (HAS/3) compete against HTTP/2 (HAS/2) must be considered seriously. However, there have been a shortage of investigations on the performance and the origin of the unfairness in such a cross-protocol scenario in order to produce proper solutions. Therefore, this paper provides a performance evaluation and root-cause analysis of the cross-protocol unfairness between HAS/3 and HAS/2. It is concluded that, due to differences in the congestion control mechanisms of QUIC and TCP, HAS/3 clients obtain larger congestion windows, thus requesting higher video bitrates than HAS/2. As the problem lies in the transport layer, existing client-side ABR-based solutions for the unfairness from the application layer may perform suboptimally for the cross-protocol case.

Evapotranspiration is a critical component of the hydrological cycle, and it has a decisive impact on the ecosystem balance in arid and semi-arid regions. The Yinchuan Plain, located in the Gobi of Northwest China, has a strong surface ET. In order to assess the ET pattern in this region, we obtained the ETa of Yinchuan Plain between 1987 and 2020 using the GEE platform. We employed the Surface Energy Balance Model (SEBAL), specifically geeSEBAL, to analyze the change pattern of ET over different seasons, years, and land types. The results show that: ① In spring, the daily ETa of the Yinchuan Plain is highest in the central lake wetland area, with a maximum value of 4.32 mm day-1. In summer, it is concentrated around the croplands and water bodies, with a maximum value of 6.90 mm day-1; In Autumn and winter, it is mainly concentrated around the water bodies and impervious areas, with maximum values of 3.93 and 1.56 mm day-1, respectively. ② From 1987 to 2020, the ET of the Yinchuan Plain showed an obvious upward and downward trend in some areas with significant land use changes, but the overall ET of the region remained relatively stable without dramatic fluctuations. ③ The evapotranspiration of different underlying land use types in the Yinchuan Plain region is as follows: water body&gt;cultivated land&gt;impervious&gt;grassland&gt;bare land. Our results showed that geeSEBAL is highly applicable in the Yinchuan Plain area. It allows for the accurate and detailed inversion of ET in the study area, which facilitates the study of regional hydrological cycle and water governance.

Classical laws of friction suggest that friction force is proportional to the normal load and independent of the nominal contact area. As a great improvement in this subject, it is now widely accepted that friction force is proportional to the real area in contact, and much work has been conducted based on this hypothesis. In present study, this hypothesis will be carefully revisited by measuring the friction force and real contact area in-site and real-time at both normal loading and unloading stages. Our experiments reveal that the linear relation always holds between friction force and normal load. However, for the relation between friction force and real contact area, the linearity holds only at the loading stage while fails at the unloading stage. This study may improve our understanding of the origin of friction.

The osteoarthritis (OA), the main cause of disability, is a chronic condition that most frequently affects older adults. As the population ages, the cost of treatment is placing pressure on the healthcare budget. As a result, it is imperative to evaluate the medicines' cost-effectiveness and the influence they have on health resource allocation. Hence, our study aims to summarize the cost and outcome of utilizing glucosamine in OA treatment. Authentic databases like Medline, Cochrane, and Scopus were adopted for the identification process up until July 2023. Our primary inclusion criteria centered on the economic evaluation of Glucosamine in OA treatments with provided the incremental cost-effectiveness ratio (ICER) at least. The Quality of Health Economic Studies (QHES) instrument was applied to grade the quality of the studies. A total of 7 qualified studies were selected and discussed the cost-effectiveness of glucosamine with or without other formulations. All of them demonstrated that glucosamine was cost-effective. There was an in-creasement of QALY when incorporating Glucosamine into conventional care. Moreover, Crystalline Glucosamine Sulfate (pCGS) was more cost-effective than the Other Formulations of Glucosamine (OFG). In overall, utilizing pCGS was more beneficial than OFG in terms both of cost and quality of life.

This study presents a tri-layer broadband metamaterial absorber which operates in the GHz range. The absorber was composed of a polyhedral iron-cobalt alloy/graphite nanosheet material arranged in a flat sheet with two punched-in rings for the top layer, a continuous FR-4 layer at the middle, and a continuous copper layer at the bottom. For the normal incidence of electromagnetic wave, the proposed absorber demonstrated an exceptional broadband absorption in a frequency range of 7.9-14.6 GHz, revealing an absorption exceeding 90%. The absorption magnitude remains to be above 90% in a frequency range of 8-11.1 GHz for transverse-electric-polarized waves at incident angles up to 55°. For both transverse-magnetic- and electric-polarized waves, the absorption exceeds 90% in a frequency range of 9.5-14.6 GHz. The physical mechanism behind the absorption properties is analyzed thoroughly through the electric- and magnetic-field distributions. The obtained results could contribute potentially to the development of microwave applications based on metamaterial absorbers, such as radar-stealth technology, electromagnetic shielding for health safety and reduced electromagnetic interferences for high-performance communications and electronic devices.

Rotary tillage is a main management tillage practices and widely applied in the North China Plain. However, the long term rotary tillage (depth of 20 cm) results in soil compaction and plow pan formation, which reduces water use efficiency and nutrient uptake, and then impedes the yield increase. In this study, a 3-year field experiment was conducted to investigate the influence of different depths of tillage on soil bulk density, field capacity, water use, photosynthetic rate, nutrients and maize yields in the North China Plain. Three depths of tillage (D20, depth of 20 cm; D25, depth of 25 cm; D30, depth of 30 cm) were assessed. D25 and D30 significantly reduced soil bulk density and improved field capacity in 10-20 and 20-30 cm soil layer, compared to D20. Soil water consumption for D25 was significantly higher 10.12% and 6.61% than that for D20 and D30, respectively. Photosynthetic rate for D25 significantly improved than that for D20 and D30. Total nitrogen in 0-20cm soil layer decreased with the depths of tillage. The maize yields for D25 significantly increased by 20.92% and 21.56% compared to that for D20 and D30, respectively. Structural equation models showed that the total effects of tillage, total nitrogen, photosynthesis and soil water consumption on yields were 0.019, -0.628, 0.121, and 0.895 (path coefficients λ), respectively. The results demonstrated that D25 could improve maize yields, water use efficiency, photosynthetic rate by improving soil water consumption. Depth of 25 cm is optimal tillage practice for the maize production in the North China Plain.

Our skin is constantly exposed to blue light (BL), which is abundant in sunlight and emitted by digital devices. Prolonged exposure to BL can lead to oxidative stress-induced damages and skin hyperpigmentation. In this study, we investigated the protective effects of tocotrienol-rich fraction (TRF) on BL-induced oxidative stress and hyperpigmentation in B16-F1 melanocytes. Alpha-tocopherol (αTP) was used as a comparator. Our results showed that TRF effectively suppressed the formation of reactive oxygen species, and preserved the mitochondrial membrane potential. Additionally, TRF exhibited anti-apoptotic properties by reducing the activation of p38 mitogen-activated protein kinase molecule and downregulating the expression of cleaved caspase-3. Moreover, TRF modulated tyrosinase activity, resulting in a lowered rate of melanogenesis and reduced melanin production. In contrast, αTP did not exhibit the significant protective effects against skin damages and pigmentation in BL-induced B16-F1 cells. Therefore, this study indicates that TRF may offer superior protective effects over αTP against the effects of BL on melanocytes. These findings demonstrate the potential of TRF as a protective natural active against BL-induced skin damages and hyperpigmentation via its antioxidative and anti-melanogenic properties.

Pipelines are widely used globally, particularly in Nigeria, to transport raw and processed hydrocarbon fluids, including crude oil, from the point of production to the shore for export, processing facilities and distribution of refined products to depots for sales and consumption. Although pipelines are designed to withstand environmental and physical shocks, intermittently, pipelines are exposed to natural or human-induced conditions that damage pipelines and disrupt their functionality. These disruptions could result from operational defects or vandalism, causing an economic loss of up to US$ 658.5 million as observed in the Niger Delta from 1990 to 2022. Furthermore, product loss of about 705,100 barrels observed over the same period has caused environmental and social impacts, damaging the natural environment, destroying livelihoods supported by the ecosystem, and deteriorating the health of residents as documented in several literatures. To mitigate these issues and ensure the safe and reliable conveyance of crude oil in pipelines, measures must be taken to timely detect spillages and intervene during oil spillages to minimize damage and loss. Such detection methods include external, visual/ biological and internal/computation-based approaches. This paper uses a mixed-method approach to review the literature on the causes and impact of crude oil pipeline leakage in the Niger Delta region of Nigeria and highlights some methods that could be applied to detect pipeline leakage, as well as their strengths and inefficiencies. This paper further assesses the joint investigation visit mechanisms for oil spill response used in the oil and gas industry in Nigeria and identified that between 2006 to 2021, it took an average of 4 days to report oil spill occurrence, and 21 days to respond. Also, for 18 percent of the spill occurrences in that period, there were no JIV. This study suggests that the gap in the JIV mechanism can be addressed by integrating technology to enhance detectability and minimize the cost of monitoring. The paper also guides the way forward to develop and improve the reliability of pipeline leak detection systems.

To estimate the progressive collapse resistance capacity of a multi-column frame tube structure with the assembled truss beam composite floor (ATBCF), the pushdown analysis, and the nonlinear dynamic analysis as well, are conducted for such a structure by using the alternate load path (ALP) method. The bearing capacities of the remaining structures at three different work conditions, which are the side middle column failure, the edge middle column failure, and the corner column failure, are individually studied, and the collapse mechanism for the remaining structures is analyzed from the aspects of the internal force redistribution and the failure mode of the second defense line. Simultaneously, the influence of the column failure time on the dynamic response of the remaining structure and the dynamic amplification coefficient are discussed. The results show that the residual bearing capacity of the remaining structure with the bottom corner column failure is higher than that of the one with the side or edge middle column failure, while the latter has a stronger plastic deformation capacity. When the ALP method is adopted to operate the progressive collapse analysis, it is reasonable to take the column failure time as 0.1 times of the first-order vertical vibration period of the remaining structure, and it is suitable to set the dynamic amplification coefficient as of 2.0, which is the ratio of the maximum dynamic displacement to the static displacement of the remaining structure under the transient loading condition.

Influenced by geological, climatic, and natural weathering factors, the Great Wall heritage is sus-ceptible to deformations, posing significant challenges to the comprehensive preservation of the Great Wall sites. To investigate techniques for monitoring deformations in extensive linear cultural heritage sites, such as the Great Wall, this study utilizes the SBAS-InSAR technique for deformation monitoring and analysis. A dataset comprising 161 Sentinel-1A images spanning from March 2017 to January 2022 was chosen for SBAS-InSAR processing, yielding a deformation velocity field. To verify result credibility, a typical mountainous segment spanning approximately 896.53 km within the Great Wall landscape corridor underwent analysis. The findings suggest that around 75.8% of the landscape corridor along the Shanxi section of the Ming Great Wall maintain relative stability, displaying deformation rates varying from -10 to 10 mm/year. The remaining 24.2% of the land-scape corridor experiences notable deformations, including a maximum subsidence rate of 33.1 mm/year and a maximum subsidence of 148.6 mm. This study illustrates the potential utility of the SBAS-InSAR technique for monitoring and evaluating surface deformations in extensive linear cultural heritage sites.

The fluorine-less noble-gas containing anions OBONgO- and OCNNgO-have been studied by correlated electronic structure calculation and density functional theory. The obtained energetics indicates that for Ng = Kr and Xe, these anions should be kinetically stable at low temperature. The molecular structures and electron density distribution suggests that these anions are stabilized by ion-induced dipole interactions with charges concentrated on the electronegative OBO and OCN groups. The current study shows that in additional to the fluoride ion, polyatomic groups with strong electronic affinities can also form stable noble-gas containing anions of the type X-...NgO.

Food insecurity has adverse consequences on women and child health in a developing country. This study aims to fill the existing research gap by examining the dynamic impacts of food insecurity on women and child health outcomes, this study adds fresh large scale panel data; and unlike the existing studies, this study estimates the short-run dynamics on food insecurity on women as child health of developing countries. We found that there was a positive association between health expenditure, women's fertility rate, women, and child health outcomes. There was a negative and statistically significant impact of food insecurity on women anemia in developing countries of Asia. Overall, the empirical analysis found that there was a strong strength to be a negative correlation between food insecurity and women and child health outcome, particularly in relation to women’s participation as a productive labor force. The study suggests that there is need to multidimensional approaches such as women and child health outcome, is needed to advance this type of research areas and should be followed broad-spectrum policy interventions to improve the women and child health status as part of sustainable development goals.

As the largest carbon pool on Earth, forest ecosystems are essential to maintaining carbon sink balance. However, accurately estimating the carbon sequestration and carbon storage of forest resources remains an urgent issue to address. Plot investigation, model estimation, and machine learning are examples of current approaches. Nevertheless, because of variables such as regional characteristics and plot size, large-scale and extensive region estimates are comparatively scarce. This study, which focuses on Tianzhu County, aims to comprehensively analyze and estimate the Net Primary Productivity (NPP), carbon storage, and carbon density of the forest ecosystem in this area by integrating data from forest resource inventory and the CASA model. The main conclusions are as follows: (1) The main vegetation types in Tianzhu County include coniferous forests, broad-leaved forests, mixed forests, and shrub forests; (2) Accordin g to the CASA model calculations, the annual cumulative NPP in Tianzhu County in 2020 ranges from a maximum of 249.63 gC/m² to a minimum of 3.40 gC/m², with the forest NPP amounting to 134,674.65 tons of carbon. Based on MODIS observation data, the forest’s NPP is 171,728.32 tons of carbon, with a maximum of 325.36 gC/m² and a minimum of 0.02 gC/m²; (3) At the pixel scale, the carbon storage of forests in Tianzhu County is 361,700 tons. Specifically, 46,500 tons of carbon are stored in coniferous forests, 1,100 tons in broad-leaved forests, 500 tons in mixed forests, and 313,600 tons in shrub forests.

In order to study the crystallinity of different density polyethylenes, the experimental study on the transformation of the conductance mechanism under high electric field was carried out. The X-ray Diffraction(XRD), Different Scanning Calorimeter(DSC), Direct Current(DC) breakdown of Low-density polyethylene(LDPE), Linear low density polyethylene(LLDPE), Medium density polyethylene(MDPE) and High-density polyethylene(HDPE) and the electric field of 5-200kV/mm were tested. Conductivity characteristics experiments, in addition, using the mathematical formula of a variety of conductance mechanisms, the electric field-current density curves of the four kinds of polyethylene were fitted to analyze the conductance transition of the above four kinds of polyethylene in non-ohmic regions under different high field strengths. mechanism. The experimental results show that as the density of polyethylene increases, the crystallinity increases continuously, and the continuous increase of crystallinity causes the electric conduction flow under the same field strength to decrease significantly. The field strength corresponding to the two turning points in the conductance characteristic curve increases simultaneously. Large, the breakdown field strength increases; through analysis, it is found that in the high field, as the electric field increases, the conductance mechanism develops from the ohmic conductance of the low field strength region to the bulk effect of the high field strength region (Poole-Frenkel). Then the electrode effect to the high field strength (Schottky), and the threshold field strength of this conductance mechanism transition increases with the increase of crystallinity.

Buckling defect will appear on the outer surface of the deformed ring during constrained ring rolling (CRR) of aluminum alloy thin wall conical ring with inner high ribs (AATWCRIHR), if the geometrical dimension of the ribs doesn't match the wall thickness. To avoid the buckling defect, a quantitative method for characterizing the degree of the buckling defect is proposed using the area of buckling profile. Then an orthogonal experimental scheme was designed taking the width of the middle rib, thickness of wall, and height of the middle rib as design variables and defining the area of buckling profile as optimization objective. Subsequently, a quadratic polynomial response surface model was established by combining the optimization algorithm with the finite element method (FEM), and the geometrical dimension of the middle ribs of the deformed AATWCRIHR is optimized. Also the optimal parameter combination to minimize the area of buckling profile is obtained and verified using FE simulation. Results show that the AATWCRIHR after optimization doesn’t generate the buckling defect during constrained ring rolling, and it is proved that the quantitative buckling defect representation method and the optimization design method based on the response surface model and the finite element simulation results are feasible for the constrained ring rolling process of the AATWCRIHR.

An undescribed diterpene, stellerterpenoid A (1) and two undescribed sesquiterpenoids, stellerterpenoids B and C (2-3), together with six known compounds, were isolated from the roots of Stellera chamaejasme L. Their structures were elucidated by extensive spectroscopic data (1D, 2D NMR, IR, UV and HR-ESI-MS). The absolute configuration of 1-3 were elucidated based on ECD calculation. Among of them, stellerterpenoid A was a rare 13, 14 - seco nortigliane diterpenoid and stellerterpenoid B was a guaiacane type sesquiterpenoid with an unusual 1, 2-diketone moiety. The known stelleraguaianone B (5) exhibited moderate activity to suppress NO production in LPS - simulated macrophages with an IC50 value of 24.76 ± 0.4 μM. None of the compounds showed inhibitory influenza virus and tumor activity.

This study aimed to present a systematic meta-analysis examining the association between Helicobacter pylori (H. pylori) infection, hemoglobin A1c levels, and the development of type 1 diabetes mellitus. The initial search identified 451 articles related to the association between H. pylori infection and T1DM. Among them, 14 articles had 2,971 participants meeting the inclusion criteria for advanced meta-analysis. A significant association was observed between H. pylori infection and T1DM, with an odds ratio (OR) of 1.87 (95% confidence interval [CI]: 1.27–2.78, p = 0.002). A subgroup analysis on H. pylori status showed that a longer duration of diabetes diagnosis and higher hemoglobin A1c levels were significantly associated with H. pylori infection (p < 0.001 for both). However, there was no significant association between H. pylori infection and the diagnostic age of diabetes (p = 0.306). These findings contribute to the understanding of the association between H. pylori infection and T1DM, thereby highlighting the potential role of H. pylori in influencing the duration and glycemic control of diabetes.

We report on space-selective crystallization of congruent and polar Sr2TiSi2O8 crystals in a stoichiometric SrO-TiO2-SiO2 glass induced by (1030 nm, 300 fs) femtosecond laser irradiation. This allows us to compare with non-congruent laser induced crystallization of polar LiNbO3, in non stoichiometric Li2O-Nb2O5-SiO2 glass and gain information on the mechanism of nanocrystals orientation with the laser polarization that we pointed out previously. Using scanning electron microscopy (SEM), Second-harmonic generation (SHG) and electron backscattered diffraction (EBSD), we studied the laser induced crystallization according to the laser processing parameters (pulse energy, pulse repetition rate, scanning speed). We found 1) a domain where the laser track is filled with crystals not perfectly textured (low energy), 2) a domain where an amorphous volume remain surrounded by a crystallized shell (high energy). This arises from Sr out-diffusion and may gives rise to crystallization of both SrTiO3 and Sr2TiSi2O8 phases at low speed. In the one-phase domain (at higher speed), it is found the possibility to elaborate a tube with a perfect fresnoite texture. Significant difference in size and morphology whereas crystallization threshold remains similar are discussed based on glases thermal propeties. Contrarily to Li2O-Nb2O5-SiO2 (LNS) glass, no domain of oriented nanocrystallization controlled by the laser polarization has been found in SrO-TiO2-SiO2 (STS) glass, which is attributed to the larger crystallization speed in STS glass. No nanogratings have also been found that is likely due to the congruency of the glass.

The article delves into the intricate phase transitions of 1-Octadecanol and n-Nonadecane within a binary system, unveiling dynamic structural changes under varying conditions. Through Fouri-er-transform infrared (FTIR) analysis, specific molecular vibrations were identified, shedding light on the molecular composition and interactions. The study highlights the challenges in detecting subtle phase transitions and emphasizes the individuality of molecular behaviours in closely related compounds. The findings underscore the complexity of phase transitions in binary systems and advocate for a nuanced approach to studying molecular structures and behaviours. Addi-tionally, the research contributes valuable insights into the molecular dynamics of Organic Polymer Functional Adsorption Materials, offering implications for synthetic waxy layers in plant epidermis.

Structural health monitoring has been studied by a number of researchers as well as various industries to keep up with the increasing demand for preventive maintenance routines. This work presents a novel method for reconstruct prompt, informed strain/stress responses at the hot spots of the structures based on strain measurements at remote locations. The structural responses measured from usage monitoring system at available locations are decomposed into modal responses using empirical mode decomposition. Transformation equations based on finite element modeling are derived to extrapolate the modal responses from the measured locations to critical locations where direct sensor measurements are not available. Then, two numerical examples (a two-span beam and a 19956-degree of freedom simplified airfoil) are used to demonstrate the overall reconstruction method. Finally, the present work investigates the effectiveness and accuracy of the method through a set of experiments conducted on an aluminium alloy cantilever beam commonly used in air vehicle and spacecraft. The experiments collect the vibration strain signals of the beam via optical fiber sensors. Reconstruction results are compared with theoretical solutions and a detailed error analysis is also provided.

The intestinal microbiota, comprised of bacteria, archaea, and phages, inhabits the gastrointestinal tract of the organism. Male reproductive sterility is currently a prominent topic in medical research. Increasing research suggests that gut microbiota dysbiosis can result in various reproductive health problems. This article specifically investigates the impact of gut microbiota dysbiosis on male reproductive infertility development. Gut microbiota imbalances can disrupt the immune system and immune cell metabolism, affecting testicular growth and sperm production. This dysfunction can compromise the levels of hormones produced and secreted by the endocrine glands, affecting male reproductive health. Furthermore, imbalance of the gut microbiota can disrupt the gut-brain-reproductive axis, resulting in male reproductive infertility. This article will explore how the imbalance of the gut microbiota impacts male reproductive infertility through immune regulation, endocrine regulation, and interactions of the gut-brain-reproductive axis, concluding with recommendations for prevention and treatment.

Concrete cracks and local damage can affect the bond performance between concrete and steel bars, thereby reducing the durability of reinforced concrete structures. Compared with general concrete crack repair methods, biomineralization repair not only has effective bonding capabilities but is also particularly environmentally friendly. In view of this, this study aimed to apply biomineralization technology to repair damaged fiber-reinforced lightweight aggregate concrete (LWAC). Two groups of LWAC specimens were prepared. The control group used lightweight aggregates (LWAs) without bacterial spores and nutrient sources, and the experimental group used LWAs containing bacterial spores and nutrient sources. These specimens were first subjected to compression tests and pull-out tests, respectively, and thus were damaged. After the damaged specimen healed itself in different ways for 28 days, secondary compression and pull-out tests were conducted. The self-healing method of the control group involved placing the specimens in an incubator. The experimental group was further divided into experimental group I and experimental group II. The self-healing method of experimental group I was the same as that of the control group. The self-healing method of experimental group II involved soaking the specimen in a mixed solution of urea and calcium acetate for two days, and then taking it out and placing it in an incubator for two days, with a cycle of four days. The test results showed that, compared with the control group specimens, the relative bond strength ratio of the experimental group II specimens increased by 17.9%. Moreover, the EDS and XRD analysis results confirmed that the precipitate formed at the crack was calcium carbonate, which improved the compressive strength and bond strength after self-healing. This indicates that the biomineralization maintenance method used in experimental group II is more effective.

Acting as the most abundant and widely distributed volatile secondary metabolites in plants, terpenoids play crucial roles in diverse physiological regulations and metabolic processes. Terpene synthases occupy a decisive proportion in determining the composition and diversity of terpenoids; though their regulatory effects have been extensively investigated across various plant species, limited studies have focused on the upstream transcriptional regulation of terpene synthases. In this study, we unveil linalool as the predominant volatile compound in Freesia hybrida flowers, demonstrating a gradual release pattern during flower blooming. In the context of the transcriptome, a typical MYB transcription factor, FhMYB108, was screened based on digital expression profile correlation analysis and homologous gene comparison. FhMYB108 is capable of regulating the expression of terpene synthase FhTPS1, and both their expression levels exhibit a gradual increase concomitant with flower opening. Moreover, transcriptional regulation and transient expression assays revealed that FhMYB108 exerts a stimulatory effect on the transcription of A. thaliana AtTPS14, while no significant increase in AtTPS14 expression was observed upon stabilization of FhMYB108 in Arabidopsis. Investigate its reason, the highly expressed AtMYC2 in A. thaliana can interact with FhMYB108 to suppress the activation of AtTPS14 by FhMYB108. The present study not only elucidated the regulatory mechanism underlying linalool synthesis, but also discovered the synergistic effect of MYB and bHLH transcription factors in governing the biosynthesis of volatile terpenoids.

Flexible and stretchable conductive materials have received significant attention in several applications such as flexible displays and sensors. In this paper, we report a highly dispersed porous Ag nanoflakes with clean surfaces were fabricated through an explosive growth process. The evolution process from silver nanoflakes to nanomeshes occurred by the novel “dissolution–recrystallization” solvothermal process. The as-obtained Ag meshes have the dual nature of nanoflakes and nanoparticles, which could create an intercross and interpenetration conductive network structures between silver and polymer in the printed elastic conductor, therefore, the silver meshes as conductive fillers used in elastic conductor simultaneously exhibit high conductivity and mechanical durability.

The continental shale layers are more complex in matrix pore-microfracture interactions and connectivity characteristics under the influence of tuff devitrification, which limits the explicit understanding of the coupling relationship between wettability and pore structure, as well as hydrocarbon flow behavior. Therefore, the influence of tuffaceous components on the reservoir formation mechanism and oil-rich effect of the continental shale formation system is a critical issue to be solved. The Upper Triassic Yanchang Formation tuffaceous shale in Ordos Basin and the Middle Permian Jingjingzigou Formation tuffaceous shale in the southern margin of Junggar Basin is taken as the research objects, using whole-rock mineral composition analysis, FE-SEM observation and digital image processing and extraction, as well as wettability angle determination and spontaneous imbibition experiments to illustrate the influence of the difference of devitrification extent on reservoir pore connectivity and interfacial wettability in two different environments of freshwater and saline lacustrine basins, and summarize the reservoir formation differential pattern under the influence of devitrification. The results show that the saline lacustrine is significantly modified by devitrification. The pore plane porosity of the devitrified tuffaceous shales in the saline lacustrine is higher than that of the tuffaceous shales in the freshwater; the oleophilic of the saline lacustrine tuffaceous shales is better than that of the tuffaceous shales in the freshwater, moreover, the pore connectivity of the saline lacustrine tuffaceous shales is better than that of the tuffaceous shales in the freshwater. Wettability and connectivity control the storage performance of shale oil in the tuffaceous shales formation system. The more oleophilic the reservoir wettability is, the better the pore connectivity is, and the better the reservoir of tuffaceous shale formation system is. According to the different extents of devitrification, two different reservoir formation models of freshwater and saline lacustrine are established, which are of great theoretical and practical significance to enrich the theory of shale oil enrichment and reservoir formation in the continental shale formation system and to guide the exploration of continental shale oil benefits.

A new quinazolinone alkaloid, named peniquinazolinone A (1), as well as eleven known com-pounds, 2-(2-hydroxy-3-phenylpropionamido)-N-methylbenzamide (2), viridicatin (3), viridicatol (4), (±)-cyclopeptin (5a/5b), dehydrocyclopeptin (6), cyclopenin (7), cyclopenol (8), methyl-indole-3-carboxylate (9), 2,5-dihydroxyphenyl acetate (10), methyl m-hydroxyphenylacetate (11), conidiogenone B (12), was isolated from the endophytic Penicillium sp. HJT-A-6. The chemical structures of all compounds were elucidated by comprehensive spectroscopic analysis, including 1D, 2D NMR, and HRESIMS. The absolute configuration at C-13 of peniquinazolinone A (1) was established by applying the modified Mosher’s method. Compounds 2, 3, and 7 exhibited an op-timal promoting effect on the seed germination of Rhodiola tibetica at a concentration of 0.01 mg/mL, while the optimal concentration for compounds 4 and 9 to promote Rhodiola tibetica seed germination was 0.001 mg/mL. Compound 12 showed optimal seed-germination-promoting activity at a concentration of 0.1 mg/mL. Compared with the positive drug 6-benzyladenine (6-BA), compounds 2, 3, 4, 7, 9, and 12 could extend the seed-germination period of Rhodiola tibetica up to the 11th day.

Temporal downscaling of gridded geophysical data is essential for improving climate models, weather forecasting, and environmental assessments. However, existing methods often could not accurately capture multi-scale temporal features, affecting their accuracy and reliability. To address this issue, we introduce an Enhanced Residual U-Net architecture for temporal downscaling. The architecture, which incorporates residual blocks, allows for deeper network structures without the risk of overfitting or vanishing gradients, thus capturing more complex temporal dependencies. The U-Net design inherently could capture multi-scale features, making it ideal for simulating various temporal dynamics. Moreover, we implement a flow regularization technique with advection loss to ensure that the model adheres to physical laws governing geophysical fields. Our experimental results across various variables within the ERA5 dataset demonstrate an improvement in downscaling accuracy, outperforming other methods.

The narrow parking space will result in difficulties in path planning and spot turning caused by sudden changes and discontinuities in path curvature. To address the problem, this paper investigates the performance of three path planning algorithms and proposes a path optimization algorithm. First, the narrow parking space is defined based on single-step parking of the arc-line combination parking algorithm. Second, to compare the arc-line combination algorithm, Hybrid A* algorithm, and particle swarm optimization parking algorithm under different narrow parking spaces, a multi-objective evaluation function is proposed, including three evaluation indicators, namely, the path length, the number of positive and negative conversions of vehicle speed, and the smoothness of the path. Their performance is compared by simulation conducted in MATLAB, the results show that the Hybrid A* algorithm is the better than others for narrow parking spaces. Third, to smooth the planning path, a path optimization algorithm based on the cubic B-spline curve and gradient descent is proposed. Finally, the simulation is conducted between the proposed algorithm and Hybrid A* algorithm, the result shows that the proposal can effectively eliminate the curvature mutation point and constrain the path curvature to meet the requirements of a smooth path.

A fast algorithm is established to transform points of the unit sphere into fundamental region symmetrically. With the resulting algorithm, a flexible form of invariant mappings is achieved to generate aesthetic patterns with symmetries of the regular polyhedra. This method avoids the order restriction of symmetry groups, which can be similarly extended to treat regular polytopes in n-dimensional space for n>=4.

Studies report variable effects of sex hormones on serious diseases. Severe disease and mortality rates in COVID-19 show marked gender differences that may be related to sex hormones. Sex hormones regulate the expression of the viral receptors ACE2 and TMPRSS2, which affect the extent of viral infection and consequently cause variable outcomes. In addition, sex hormones have complex regulatory mechanisms that affect the immune response to viruses. These hormones also affect metabolism through obesity, and severe disease can result from complications such as thrombosis. This review presents the latest research on the regulatory functions of hormones in viral receptors, immune responses, complications as well as their role in COVID-19 progression. It also discusses the therapeutical possibilities of these hormones by reviewing the recent findings of clinical and assay studies.

Amylin, also known as islet amyloid polypeptide (IAPP), is a metabolic homeostasis-related hormone that is produced and released by the β cells of the pancreas, the same cells that produce insulin. Insulin-degrading enzyme (IDE) is a protease enzyme that plays an essential role in the breakdown and degradation of various peptides, including insulin and amylin. Direct binding & interaction between amylin and IDE is inextricably linked to the degradation of amylin, and research and development effort in this area is crucial to understand the potential therapeutic implications of disrupting the IDE-amylin interaction in the context of conditions where metabolic homeostasis needs to be regulated, such as diabetes and obesity. Here, this article incorporates currently available experimental complex structure of amylin and IDE, and delves deep into the interstructural biophysics underlying the binding interface of the two interacting partners. With a set of comprehensive structural biophysical analysis, this article identified an intriguing region of high electrostatic potential indicative of strong binding sites between the first N-terminal lysine (Lys1, K1) residue of amylin and Glu341 (E341) of IDE. This unique electrostatic hotspot presented herein paves the way for the rational design of drug-like small molecules that can selectively disrupt this interaction, offering a targeted therapeutic strategy for improved metabolic homeostasis, particularly for patients with diabetes and obesity.

Background: Pediatric ureteropelvic junction obstruction (UPJO) is a common urinary tract issue. Accurate assessment of postoperative kidney function is crucial for prognosis. Previous studies mainly focused on postoperative renal function and individual factors. Radionuclide imaging was costly and unsuitable for long-term follow-up. For aligning closely with clinical needs, we emphasizing renal morphology enhancement, and comprehensively analyzed factors influencing UPJO surgery outcomes. Methods: We retrospectively studied 150 pediatric UPJO patients (July 2012-July 2022) with severe anteroposterior renal pelvis dilation (APD grades 4-5) who underwent laparoscopic dismembered pyeloplasty. Demographics, symptoms, preoperative findings, and postoperative renal ultrasounds were assessed. We performed multivariable logistic regression analysis to identify significant predictors of prognosis and construct a regression model. Results: Among the 150 pediatric patients, 78 (52%) showed improvement in renal morphology after surgery. In the multivariate logistic regression analysis, age at surgery, duration of hydronephrosis, body weight, and preoperative creatinine were identified as significant prognostic factors for postoperative outcomes. The nomogram (AUC: 0.92) was constructed based on these factors and could serve as a useful tool for clinicians in evaluating the surgical prognosis of children with UPJO. Conclusions: This study reveals that among pediatric patients with severe hydronephrosis resulting from UPJO, those who are younger, have a shorter duration of illness, normal serum creatinine levels, and a healthy body weight tend to experience better postoperative recovery. This finding emphasizes the importance of adopting more proactive clinical interventions when managing such cases, with the goal of achieving enhanced recovery outcomes for affected children.

The apparent metal-insulator transition (MIT) in two-dimension (2D) was discovered by Kravchenko et al. [1] more than two decades ago in strongly interacting 2D electrons residing in a Si-metal-oxide-semiconductor field-effect transistor (Si-MOSFET). Its origin remains unresolved. Recently, low magnetic field reentrant insulating phases (RIPs), which dwell between the zero-field (B=0) metallic state and the integer quantum Hall (QH) states where the Landau-level filling factor υ > 1, have been observed in strongly correlated 2D GaAs hole systems with large interaction parameter rs (~20-40) and high purity. A new complex phase diagram was proposed, which includes zero field MIT, low magnetic field RIPs, integer QH states, fractional QH states, high field RIPs and insulating phases (HFIPs) with υ < 1 in which the insulating phases are explained by the formation of Wigner crystal. Furthermore, evidences of new intermediate phases were reported. All contribute to the further understandings of the puzzle. This review article serves the purpose of summarizing those recent experimental findings and theoretical endeavors, to foster future research efforts.

Skin image analysis using artificial intelligence (AI) has recently attracted significant research interest, particularly for analyzing skin images captured by mobile devices. Acne is one of the most common skin conditions with profound effects in severe cases. In this study, we developed an AI system called AcneDet for automatic acne object detection and acne severity grading using facial images captured by smartphones. AcneDet includes two models for conducting two tasks: (1) a Faster R-CNN-based deep learning model for the detection of acne lesion objects of four types including blackheads/whiteheads, papules/pustules, nodules/cysts, and acne scars; and (2) a LightGBM machine learning model for grading acne severity using the Investigator’s Global Assessment (IGA) scale. The output of the Faster R-CNN model, i.e., the counts of each acne type, were used as input for the LightGBM model for acne severity grading. A dataset consisting of 1,572 labeled facial images captured by both iOS and Android smartphones was used for training. The results show that the Faster R-CNN model achieves a mAP of 0.54 for acne object detection. The mean accuracy of acne severity grading by the LightGBM model is 0.85. With this study, we hope to contribute to the development of artificial intelligent systems that are able to help acne patients understand more about their conditions and support doctors in acne diagnosis.

Alternative fertilizations are essential to minimize the deteriorating effects of chemical fertilizers on soil and water quality/health. Accordingly, the present work investigated the effects of combined organic-inorganic fertilization (COIF) on wheat and rice yields, soil nutrients, and soil Cd accumulation. Hence, seven different treatments were set up: control (CK); conventional fertilization (CF); optimized fertilization (OF); organic fertilizer replacing 25% (T1) and 50% (T2) of OF; and organic nitrogen (N) replacing 25% (M1) and 50% (M2) of OF-N. Overall, significant increases occurred in the yields of COIF crops. Compared with the CF, the highest wheat and rice yields happened in M1 treatment (approximately by18.5%) (P &lt; 0.05). COIF slightly alleviated soil acidification, and improved the cation exchange capacity (CEC) of the study soils. Besides, COIF treatments significantly increased the contents of total phosphorus, total potassium, available phosphorus, and available potassium by 6.35 to 16.9 %, 3.17 to 10.9 %, 5.53 to 28.7 %, and 2.6 to 12 %, respectively (P &lt;0.05). Nevertheless, negligible increases took place in Cd content of COIF soils compared with the CK. Altogether, our results concluded on 25% replacement of OF-N by organic N (M1) to effectively improve the fertility/ecological sustainability of the study soils.

Since the launch of Protein Data Bank (PDB) in 1971, Cartesian coordinate system (CCS) has been the default approach to specify atomic positions in biomolecular experimental structures with X, Y and Z. In 2020, a local spherical coordinate system (LSCS) approach was proposed as an alternative to CCS, i.e., ρ, θ and φ. Recently, the continued application of deep learning technology in protein structure prediction (PSP) saw a leap forward in the accuracy of PSP, as evidenced by AlphaFold of Google’s DeepMind. However, there still is room for the improvement of the performances of PSP algorithms to date. Given that geometrically, CCS and LSCS are like the two sides of a coin, this short article puts forward a hypothesis that the time is now ripe to end the half-a-century burial of ρ, θ and φ in PDB, and use them as LSCS features for the design of novel PSP algorithms in future.