A printed Vivaldi antenna that is optically transparent, ultra-wideband (UWB), and reconfigurable has been developed, fabricated, and tested at millimeter wave frequencies. It covers a broad frequency range of 20-30 GHz by using three PIN diodes. The diodes control the current flow to direct the beam of the antenna. The results of numerical simulations and measurements match at millimeter wave frequencies. The design of this antenna is unique as it allows for a reduction in size and ease of integration while also providing the ability to change the radiation pattern by up to 300 degrees, making it suitable for 5G and 6G communications. Additionally, this antenna can also be useful for RF applications that require dynamic switching of radiation patterns and cognitive radio.

Arsenic is naturally present in many geological formations around the world and is a major source of groundwater contamination. Bolivia is not exempt from this problem. Physical-chemical studies of water quality in deep and shallow wells have determined the presence of arsenic in some areas of the Bolivian Altiplano, valleys, and plains. In the Lake Poopó basin, water from shallow wells (up to 30 m) has arsenic concentrations that exceed the Bolivian drinking water standard and the WHO recommendation of 10 μg-As/l by up to 25 times. In peri-urban areas of Cochabamba, the arsenic content in groundwater is up to 113 μg-As/l. chronic exposure to arsenic is associated with neurological and dermatological problems and carcinogenic effects. To date, no measures have been taken to mitigate the arsenic problem for the rural population, who often rely on arsenic-contaminated water as their only source of drinking water. This contamination represents a serious threat to the health and economic well-being of the inhabitants and ecosystem in these areas. In this work, for arsenic removal, iron and iron oxide nanoparticles obtained from recycling metal chips by top-down and bottom-up technology have been used for arsenic adsorption in an experimental filter combined with other artisanal filtering materials in the form of layers. The results have shown that water contaminated with arsenic after passing through the filter reduces the concentration of total arsenic filtered from 83, 52 ppb to less than 5 ppb, less than the Bolivian standard 512 of 10 ppb for drinking water.

Infrared thermography has already been proven to be a significant method in non-destructive evaluation since it gives information with immediacy, rapidity and low cost. However, the thorniest issue for wider application of IRT is the quantification. In this work, we proposed a specific depth quantifying technique by employing the Gated Recurrent Units (GRU) in composite material samples via pulsed thermography (PT). Carbon Fiber Reinforced Polymer(CFRP) embedded with flat bottom holes were designed via Finite Element Method (FEM) modeling in order to precisely control the depth and geometrics of the defects. The GRU model automatically quantified the depth of defects presented in the CFRP material. The proposed method evaluated the accuracy and performance of synthetic CFRP data from FEM for defect depth predictions.

The saturation properties of symmetric and asymmetric nuclear matter have been computed using the finite range simple effective interaction having Yukawa form-factor. The results of higher order derivatives of the energy per particle and the symmetry energy computed at saturation, namely, Q0, Ksym, Kτ, Qsym, are compared with the corresponding range of values extracted from studies involving theory, experiment and astrophysical observations. The ability of the equations of state computed with this simple effective interaction in predicting the threshold mass for prompt collapse in binary neutron star merger and gravitational redshift have been examined in terms of the compactness of the neutron star and the incompressibility at the central density of the maximum mass star. The correlations existing between neutron star properties with the nuclear matter saturation properties have been analyzed and compared with the predictions of other model calculations.

Coded aperture 3D imaging techniques have been rapidly evolving in the recent years. The two main directions of evolution are in aperture engineering to generate the optimal optical field and in development of computational reconstruction to reconstruct the object’s image from the intensity distribution with a minimal noise. The goal is to find the ideal aperture-reconstruction method pair and if not, to optimize one to match the other for designing an imaging system with required 3D imaging characteristics. Lucy-Richardson-Rosen algorithm (LR²A), a recently developed computational reconstruction method was found to perform better than its predecessors such as matched filter, Weiner filter, phase-only filter, Lucy-Richardson algorithm and non-linear reconstruction (NLR) for certain apertures when the point spread function (PSF) is a real and symmetric function. For other cases of PSF, NLR performed better than the rest of the methods. In this tutorial, LR²A has been presented as a generalized approach for any optical field along with MATLAB codes for reconstruction of any image when the PSF is known. The common problems and pitfalls in using LR²A has been discussed. Simulation and experimental studies for common optical fields such as spherical, Bessel, vortex beams and exotic optical fields such as Airy, scattered and self-rotating beams have been presented. From this study, it can be seen that it is possible to transfer the 3D imaging characteristics from non-imaging type exotic fields to indirect imaging systems faithfully using LR²A. The application of LR²A to medical images such as colonoscopy images and cone beam computed tomography images with synthetic PSF has been demonstrated. We believe that the tutorial will provide a deeper understanding of computational reconstruction using LR²A.

This note applies the Logistic model approximation to determine the suitable start and end dates for the observed epidemic curves in the total number of cases for different countries. The Logistic model is presented and explicit relations for the beginning and end dates are obtained together with the total epidemic duration. Using data from Brazil, Germany, Italy, and South Korea, the extreme dates are calculated. Since the epidemic onset time is found, a fair comparison of the epidemic curve for these countries is obtained. The result does not depend on the poor statistics available in the early phase of the epidemic when the initial number of infectives is unknown. In fact, the total duration depends only on the characteristic time parameter of the LM model.

The purpose of this project is to develop and build an extensible fixture. This fixture is ideal to milling, drilling, and shaping operations. Jigs and fittings are often the most cost-effective methods of mass fabricating a component. As a result, jigs and fittings are used and play a vital part in the mass production system. These are specialist work holding and tool-guiding devices. The quality of jigs and fixtures used in a process has a substantial impact on its performance. A fixture is distinctive because it is meant to fit a given area or shape. The basic purpose of a fixture is to find and, in certain instances, hold a workpiece throughout an operation. A jig differs from a fixture in that it leads the tool to the right position or movement during an operation, in addition to locating and supporting the workpiece. When a key is reproduced, the original key serves as a base for the path reader, which regulates the tool's movement to construct the duplicate key. In this situation, a CWC machine's route reader works as a jig, with the original being referred to as the template. Sometimes the template and jig refer to the same part of a production system.

In recent years, the application of Indoor Positioning Systems (IPS) has experienced a significant increase in demand, with the aging of the world’s population and their changing lifestyles. While outdoor positioning systems, such as the Global Positioning System (GPS), have significantly advanced over the years, indoor positioning has been restrained by the limitations of the employed technologies. This paper presents a hybrid wireless positioning system able to locate wearables indoor accurately. It is based on the Wi-Fi and Bluetooth technologies, by using trilateration to determine the position of Bluetooth low energy (BLE) wearable devices with an accuracy of up to 1.8 meters. A graphical user interface (GUI) was used to illustrate the performance of the proposed systems, by allowing users to visualize the captured data in two dimensions and three- dimensions in real-time.

In a meta-analysis, we examined the behavioral portfolio of invasive brown anoles (Anolis sagrei) and native green anoles (Anolis carolinensis) in urban and non-urban environments. We hypothesized that invasive anoles should display more agonistic and bold signals (head bobbing, dewlap extensions and pushups) than their native range counterparts, and their native competitors. We found that in urban settings, anoles of both species signaled more with dewlap extensions than with head-bobs. The brown anoles displayed significantly higher in non-urban habitats and their native range compared to urban habitats and invasive ranges. The outcome of our analysis suggests that brown anoles have plastic behavioral portfolios, whereas the green anole have relatively balanced preferences for head-bobbing irrespective of the habitat in which the populations were collected. We attribute the success of the brown anole invasion to the flexible strategy in face of higher mate competition, higher predation risks, and less resource competition in the urban environments and invasive ranges. Lastly, we observed publication biases. More studies are conducted with urban and invasive brown anoles and specifically in manipulative mesocosm experimental settings - transplanting populations from native field settings. We show this altered the display rates across all studied signals.

In metal additive manufacturing (AM), precise temperature field prediction is crucial for process monitoring, automation, control, and optimization. Traditional methods, primarily offline and data-driven, struggle with adapting to real-time changes and new process scenarios, which limits their applicability for effective AM process control. To address these challenges, this paper introduces the first physics-informed (PI) online learning framework specifically designed for temperature prediction in metal AM. Utilizing a physics-informed neural network (PINN), this framework integrates a neural network architecture with physics-informed inputs and loss functions. Pretrained on a known process to establish a baseline, the PINN transitions to an online learning phase, dynamically updating its weights in response to new, unseen data. This adaptation allows the model to continuously refine its predictions in real-time. By integrating physics-informed components, the PINN leverages prior knowledge about the manufacturing processes, enabling rapid adjustments to process parameters, geometries, deposition patterns, and materials. Empirical results confirm the robust performance of this PI online learning framework in accurately predicting temperature fields for unseen processes across various conditions. It notably surpasses traditional data-driven models, especially in critical areas like the Heat Affected Zone (HAZ) and melt pool. The PINN’s use of physical laws and prior knowledge not only provides a significant advantage over conventional models but also ensures more accurate predictions under diverse conditions. Furthermore, our analysis of key hyper-parameters—learning rate and batch size of the online learning phase—highlights their roles in optimizing the learning process and enhancing the framework’s overall effectiveness. This approach demonstrates significant potential to improve the online control and optimization of metal AM processes.

We discuss methods for calculation of critical indices and amplitudes from the perturbative expansions. Several important examples of the Stokes flow through 2D and 3D channels are brought up. Power series for the permeability derived for small values of amplitude are employed to calculation of various critical exponents in the regime of large amplitudes. Special nonlinear approximations valid for arbitrary values of the wave amplitude are derived from the expansions. The technique developed for critical phenomena is applied then for relaxation phenomena. The concept of time-translation invariance is discussed, its spontaneous violation and restoration considered. Emerging probabilistic patterns correspond to a local breakdown of time-translation invariance. Their evolution leads to the timetranslation symmetry complete (or partial) restoration. We estimate typical time extent, amplitude and direction for such restorative process. The new technique is based on explicit introduction of origin in time. After some transformations we come to the exponential and generalized, exponential-type solution with explicit finite time scale, which was only implicit in initial parametrization with polynomial approximation. The concept of crash as a relaxation phenomenon, consisting of time-translation invariance breaking and restoration, is put forward. COVID-19 related mini-crash in the time series for Shanghai Composite is discussed as an illustration.

The Indus basin is considered as the one with the highest dependence on snowmelt runoff in High Mountain Asia. The recent High Mountain Asia snow reanalysis enables to go beyond previous studies by evaluating both snowmelt and snow sublimation at the basin scale. Over 2000-2016, basin-average snowmelt is 101 11 Gt.a^-1 (121 ± 13 mm.a^-1), which represents about 25-30% of basin-average annual precipitation. Snow sublimation accounts for 11% of the mean annual snow ablation, but with a large spatial variability across the basin.

We review extrapolation methods for calculation of critical points and indices from the perturbative expansions by means of Pad\'{e}-based techniques and their various post-Pad\'{e} extensions by means of root and factor approximants. Factor approximants are applied to finding critical points. Roots are employed within the context of finding critical index. Additive self-similar approximants are discussed and $DLog$ additive recursive approximants are introduced as their generalization. They are applied to the problem of interpolation.

A large amount of data is produced every day by stakeholders of the Air Traffic Management (ATM) system, in particular airline operators, airports, and air navigation service provider (ANSP). Most data is kept private for many reasons, including commercial and security concerns. More than data, shared information is precious, as it leverages intelligent decision-making support tools designed to smooth daily operations. We present a framework to detect, identify and characterise anomalies in past aircraft trajectory data. It is based on an open source of ADS-B based aircraft trajectories, and extracted information can benefit a wide range of stakeholders: Air Traffic Control (ATC) training centres could play more realistic simulations; ANSP may improve capacity indicators; academics improve safety models and risk estimations; and commercial stakeholders, like airlines and airports, may use such information to improve short-term predictions and optimise their operations. The technique is based on autoencoding artificial neural networks applied on flows of trajectories, which provide a useful reading grid associating cluster analysis with quantified level of abnormality. In particular, we find that the highest anomaly scores correspond to poor weather conditions, whereas anomalies with a lower score relate to ATC tactical actions.

The CoDRIVE solution builds on R&D in the development of connected and autonomous vehicles (CAVs). The mainstay of the system is a low-cost GNSS receiver integrated with a MEMS grade IMU powered with CoDRIVE algorithms and high precision data processing software. The solution integrates RFID (radio-frequency identification) localisation information derived from tags installed in the roads around the University of Nottingham. This aids the positioning solution by correcting the long-term drift of inertial navigation technology in the absence of GNSS. The solution is informed of obscuration of GNSS through city models of skyview and elevation masks derived from 360-degree photography. The results show that predictive intelligence of the denial of GNSS and RFID aiding realises significant benefits compared to the inertial only solution. According to the validation, inertial only solutions drift over time, with an overall RMS accuracy over a 300 metres section of GNSS outage of 10 to 20 metres. After deploying the RFID tags on the road, experiments show that the RFID aided algorithm is able to constrain the maximum error to within 3.76 metres, and with 93.9% of points constrained to 2 metres accuracy overall.

There is limited information on Tamarind production, trade and value added products in Kenya. Of late, there is growing interest in the domestic and export markets due to its multiple uses. The objective of this paper is to review existing literature to identify the missing value chain links which may help catalyse the scaling up of production and commercialization of Tamarind. Selected literature and interviews with traders and extension staff in the Coastal Counties were used to collect information for this study. Tamarind fruits are mainly collected in the wild in semi-arid areas of the country and marketed through informal channels. Mombasa is the terminal market for tamarind from Kenya and Uganda, from where domestic consumers and exporters obtain their supplies. Globally, virtually every part of tamarind tree (pulp, seed, leaves, flowers, bark and roots) has either nutritional, industrial or medicinal value. Tamarind fruit contains substantial levels of carbohydrates, proteins, vitamins, minerals and essential amino acids making it potentially useful in addressing wide spread malnutrition. Its anti-oxidant, anti-inflammatory, anti-microbial, anti-fungal and anti-diabetic properties gives tamarind wider application in conventional and traditional medicine. The findings suggest that scaling up the production and commercialization of tamarind in the country requires both public and private sector investment. The structure of this partnership should consist of the following value chain links: An efficient Seed / seedling system as a source of planting materials; production hubs by farmer associations, government institutions and private farms; aggregation centres for assurance of volumes and quality; processing, value addition and product diversification; an efficient distribution systems of wholesalers and retailers, particularly supermarkets; exporters and consumers. The agenda for further research should include breeding and availing early maturing cultivars demanded by the export market, quality management andvalue addition technologies.

Quantum correlations, especially time correlations, are crucial in ghost imaging in order to significantly reduce the background noise on the one hand while increasing the imaging resolution. Moreover, the time correlations serve as a critical reference, distinguishing between signal and noise, which in turn enable clear visualization of biological samples. Quantum imaging also addresses the challenge involved in imaging delicate biological structures with minimal photon exposure and sample damage. Here we explore the recent progress in quantum correlation-based imaging, notably its impact on secure imaging and remote sensing protocols as well as on biological imaging. We also exploit the quantum characteristics of heralded single-photon sources (HSPS) combined with decoy-state methods for secure imaging. This method uses Quantum Key Distribution (QKD) principles to reduce measurement uncertainties and protect data integrity. It is highly effective in low-photon-number regimes for producing high-quality, noise-reduced images. The versatility of decoy-state methods with WCSs (WCS) is also discussed, highlighting their suitability for scenarios requiring higher photon numbers. We emphasize the dual advantages of these techniques: improving image quality through noise reduction and enhancing data security with quantum encryption, suggesting significant potential for quantum imaging in various applications, from delicate biological imaging to secure quantum communication.

The second external cause of death from unintentional injuries is falls in people over 60, a worldwide public health problem. Associated factors are identified early in Primary Health Care. Thus, we analyze professional narratives about older adults/old age and the organization of services in the presence of fall-inducing frailty. A structured narrative was applied under the following stages: understanding the context; setting/plot/character analysis; and interpretive synthesis. Data were collected from August to November 2022, distributing 21 health professionals in three Narrative Focus Groups. In the analyses, the collective conceptions dialogued with Bourdieu’s Epistemology of field, habitus, and capital. Among the results, technical and common sense representations of older adults were simultaneously observed, along with the belief of old age as a problematic life stage. Care is centered on the installed disease/ailment. Encouraging autonomy and self-care emerges in integrative health practices, which older adults underestimate. Professionals access the lives of older adults according to their habitus, which, in turn, is structured (structuring) in the disputes for installed capital. Thus, the care provided disregards subjectivities and symbolic systems associated with falls.

The purpose of this study is to provide an accurate formula for calculating entropy for short DNA sequences and to demonstrate how to use it to examine leukemia patient surviving. We used IDIBAPS leukemia patient’s data base with 117 anonymized records. The generalized form of the Robust Entropy Estimator (EnRE) for short DNA sequences was proposed and key EnRE futures was showed. The Survival Analysis has been done using statistical package IBM SPSS. Entropy EnRE were calculated for leukemia patients for two samples: A. 2 groups divided by median EnRE and B. 2 groups of patients were formed according to their belonging to 1st and 4th quartiles of EnRE. The result of survival analysis are statistically significant: A. p < 0.05; B. p < 0.005. The death hazard for a patient with EnRE below median is 1.556 times that of a patient with EnRE over median and that the death hazard for a patient of 1st quartile (lowest EnRE) is 2.143 times that of a patient of 4th quartile (highest EnRE). The transition from median to quartile patients’ groups with more EnRE differentiation confirmed the unique significance of the entropy of DNA sequences for leukemia patients surviving.

Currently, peptic ulcers are widely studied as an infectious disease caused by Helicobacter pylori primarily due to 3 supporting evidences, and this etiology may explain the other 3 observations, but cannot confront the challenges of the 15 major characteristics and the other 75 observations/phenomena of peptic ulcers. To address the challenges, a recently published Complex Causal Relationship with its accompanying methodologies was applied to analyze existing data. Peptic ulcers are identified as a psychosomatic disease triggered by psychological stress, where Helicobacter pylori plays a secondary role in only the late phase of ulceration. This new etiology elucidated all the 15 major characteristics and 81 observations/phenomena of peptic ulcers in a series of 6 articles. This sixth article focuses exclusively on the controversies surrounding the role of Helicobacter pylori in peptic ulcers. In-depth analyses find that all the 3 evidences supporting “peptic ulcers are an infectious disease caused by Helicobacter pylori” are deceiving, and 2 of the 3 explainable observations may have been misinterpreted. Meanwhile, the definitions of ‘etiological factor’ and ‘causality’ do not support ‘H. pylori infection is an etiological factor of peptic ulcers’, and existing literatures have presented a controversial view on the role of Helicobacter pylori in peptic ulcers. Interestingly, if “peptic ulcers are an infectious disease caused by Helicobacter pylori” is considered an illusion, all the characteristics of the disease, along with all the clinical, epidemiological, and laboratory observations/phenomena, can be fully understood. This illusion has misguided peptic ulcer research over the past 36 years with little progress in the field, and that may represent a widespread situation in modern medical research, resulting in a direct interference with the true understanding of disease. Evidently, keeping the concept “illusion” in mind may help remove a huge obstacle that impedes medical advance, thereby facilitating the in-depth study of disease.

Industrial fires at facilities including waste management sites, warehouses, factories, chemical works and fuel storage depots are relatively frequent occurrences. Often, these fires occur adjacent to urban communities and result in ground-level airborne pollutant concentrations that are well above guideline values. Land, water, livestock and crops may also be contaminated by the emissions and by firefighting activities. Moreover, impacted communities tend to have a higher proportion of minority ethnic populations, individuals with underlying health vulnerabilities, as well as those of lower socio-economic status. Nevertheless, this is an aspect of air quality that is under-researched, and so this review aims to highlight the public health hazards associated with industrial fires and the need for an effective, coordinated, public health response. We also review the range of monitoring techniques that have been utilised in such fires and highlight the role of dispersion modelling in predicting plume trajectories and in estimating population exposure. We recommend establishing 1-h guideline values for particulate matter to facilitate timely public health interventions and we highlight the need to review regulatory and technical controls for sites prone to fires, particularly in the waste sector.

Molecular visualisation is fundamental in the current scientific literature, textbooks and dissemination materials, forming an essential support for presenting results, reasoning on and formulating hypotheses related to molecular structure. Visual exploration has become easily accessible on a broad variety of platforms thanks to advanced software tools that render a great service to the scientific community. These tools are often developed across disciplines bridging computer science, biology and chemistry. Here we first describe a few Swiss Army knives geared towards protein visualisation for everyday use with an existing large user base, then focus on more specialised tools for peculiar needs that are not yet as broadly known. Our selection is by no means exhaustive, but reflects a diverse snapshot of scenarios that we consider informative for the reader. We end with an account of future trends and perspectives.

The combination of eco-respectful epoxy compounds with the humins, a by-product of biomass chemical conversion technologies, allow the obtention of materials with high added value. In this work, we propose the chemical connection study of humins with two aliphatic diepoxides through the copolymerization reactions to synthesize sustainable bio-based thermosets. The mechanism insights for the crosslinking between the epoxides and humins was proposed considering the different functionalities of the humins structure. FT-IR spectroscopy, 1 D and 2 D NMR spectroscopy techniques were used to build the proposed mechanism. By these techniques, the principal chain connections and the reactivity of all the components were highlighted in the synthesized networks.

Aerosol optical depth (AOT) was measured at Xavier University of Louisiana (29.96ᵒ N, 90.11ᵒ W and about 3m above sea level) using a hand-held sun photometer. AOT was measured at two different wavelengths (green at 505nm and red at 625nm) during the period from Sept-2017 to Feb-2018. In this study, we investigate the relationship between AOT and temperature, precipitation, barometric pressure and relative humidity. The maximum monthly average value for green AOT was 0.176 (measured in September) and the minimum monthly value is 0.040 (measured in January). For the red AOT the maximum monthly average value was 0.123 (measured in September) and the minimum is 0.034 (measured in December). The AOT–temperature relationship was predominantly positive, meaning that high AOT values correspond to high temperatures and low AOT values correspond to low temperatures. Relationship between AOT and rainfall is negative, meaning high rainfall averages are associated with low AOT values. AOT and atmospheric pressure have a predominantly negative relationship. The relationship between relative humidity and AOT is a complicated one and is hard to qualify as relative humidity varies very little during the study period.

Forensic anthropologists play a key role in skeletal trauma analysis and commonly use macroscopic features to distinguish between trauma types. However, this approach can be challenging, particularly in cases of highly comminuted or incompletely recovered fractures. Histological analysis of microscopic fracture characteristics in fractured bones may thus help provide additional information on trauma type and bone fracture biomechanics in general. This study analysed the extent of microcrack damage to osteons in long bones with blunt force trauma (BFT) and gunshot trauma (GST), from both traumatic death cases and post-mortem experimental fractures. We identified four types of osteonal damage (OD). In traumatic death cases, OD affecting the inside of the osteon and compromising the Haversian canal (type 1) was found to be indicative of BFT. Moreover, OD affecting the cement line (type 3) and interstitial lamellae (type 4) was more common in the GST samples. OD affecting the inside of the osteon without compromising the Haversian canal (type 2) was not found to be indicative of either trauma type. In cases of experimental fractures, our study revealed that post-mortem fractures in dry bone samples featured the highest amount of OD, particularly of type 4. This study also found that the experimentally produced GST featured similar OD pattern to GST death cases. These findings support our hypothesis that there are distinct osteonal damage patterns in human long bones with BFT and GST, which are of relevant value for trauma analysis in forensic anthropology.

The established classical method of treating oil refinery effluent is flotation followed by biological treatment. Membrane bioreactors (MBRs) offer more advanced treatment, producing a clarified and potentially reusable treated effluent, but demand robust pretreatment to remove oil and grease (O&G) down to consistent, reliably low levels. An analysis of a full-scale conventional oil refinery ETP based on flotation alone, coupled with projected performance, energy consumption and costs associated with a downstream MBR, have demonstrated satisfactory performance of flotation-based pre-treatment. The flotation processes, comprising an API separator followed by dissolved air flotation (DAF), provided ~90% removal of both total suspended solids (TSS) and O&G coupled with 75% COD removal. The relative energy consumption and cost of the pretreatment, normalised against both the volume treated and COD removed, was considerably less for the API-DAF sequence compared to the MBR. The combined flotation specific energy consumption in kWh was found to be almost an order of magnitude lower than for the MBR (0.091 vs 0.86 kWh per m3 effluent treated), and the total cost (in terms of the net present value) around one sixth that of the MBR. However, the nature of the respective waste streams generated and end disposal of waste solids differs significantly between the pretreatment and MBR stages.

Multi- and hyper-spectral, multi-angular top-of-canopy reflectance data call for an efficient retrieval system which can improve the retrieval of standard canopy parameters (as albedo, LAI, fAPAR), and exploit the information to retrieve additional parameters (e.g. leaf pigments). Furthermore consistency between the retrieved parameters and quantification of uncertainties are required for many applications. % (2) methods We present a retrieval system for canopy and sub-canopy parameters (OptiSAIL), which is based on a model comprising SAIL, PROSPECT-D (leaf properties), TARTES (snow properties), a soil model (BRDF, moisture), and a cloud contamination model. The inversion is gradient based and uses codes % created by Automatic Differentiation. The full per pixel covariance-matrix of the retrieved parameters is computed. For this demonstration, single observation data from the Sentinel-3 SY_2_SYN (synergy) product is used. The results are compared with the MODIS 4-day LAI/fPAR product and PhenoCam site photography. OptiSAIL produces generally consistent and credible results, at least matching the quality of the technically quite different MODIS product. For most of the sites, the PhenoCam images support the OptiSAIL retrievals. The system is computationally efficient with a rate of 150 pixel per second (7 millisecond per pixel) for a single thread on a current desktop CPU using observations on 26 bands. Not all of the model parameters are well determined in all situations. Significant correlations between the parameters are found, which can change sign and magnitude over time. OptiSAIL appears to meet the design goals, puts real-time processing with this kind of system into reach, seamlessly extends to hyper-spectral and multi-sensor retrievals, and promises to be a good platform for sensitivity studies. The incorporated cloud and snow detection adds to the robustness of the system.

Phytochemicals have a long and successful history in drug discovery. With recent advancements in analytical techniques and methodologies, discovering bioactive leads from natural compounds has become easier. Computational techniques like molecular docking, QSAR modelling and machine learning, and network pharmacology are among the most promising new tools that allow researchers to make predictions concerning natural products' potential targets, thereby guiding experimental validation efforts. Additionally, approaches like LC-MS or LC-NMR speed up compound identification by streamlining analytical processes. Integrating structural and computational biology aids in lead identification, thus providing invaluable information to understand how phytochemicals interact with potential targets in the body. Emerging computational approach is machine learning involving QSAR modelling and deep neural networks that interrelate phytochemical properties with diverse physiological activities such as antimicrobial or anticancer effects.

A proportion of osteoarthritis (OA) patients are unsatisfied with post-operative outcomes following total joint replacement surgery (TJR), with insufficient pain relief or poor functional improvement. Predicting those will have poor outcomes would be beneficial for patients and clinicians. The aim of this study was to determine the relationship between baseline anthropometric data and the concentration of pre-operative serum and peri-operative synovial fluid (SF) cytokines with 7-month post-operative outcomes in a cohort of knee and hip OA patients. 160 OA patients were recruited who were scheduled for TJR. The concentration of 24 cytokines were measured in blood and SF by multiplex assay. EQ5Dindex health status was assessed pre-operatively and at 7-months post-operatively. 13% of patients were identified as non-responders based on EQ5Dindex. Compared to responders, non-responders were of higher BMI, had greater waist and hip circumference and had higher levels of SF leptin but lower levels of SF Resistin (p<0.05). Linear regression analysis found a significant relationship between pre-operative body weight and post-operative response (ΔEQ5Dindex; r=0.222, p=0.049). The combination of body weight with SF amphiregulin and SF IL-6 provided an improved predictive model of post-operative response (r=0.470, p=0.035).

The art of representing source code is pivotal in numerous programming analysis applications. Recent strides in neural networks have marked notable successes in this realm. However, the peculiar structural characteristics inherent in programming languages have not been fully exploited in existing models. While neural models based on abstract syntax trees (ASTs) adeptly manage the tree-like nature of source codes, they fall short in discerning the diverse substructural nuances within programs. This paper introduces the Dynamic Syntax Tree Model (DSTM), an innovative approach that fuses various neural network modules into tree architectures tailored to the specific AST of the input. Distinct from preceding tree-based neural models, DSTM adeptly discerns the semantic variances across different AST substructures. We validate DSTM through rigorous testing in program classification and code clone detection, outperforming contemporary methods and demonstrating the benefits of harnessing intricate source code structures.

The three-dimensional printing of scaffolds is an interesting alternative to the traditional techniques of periodontal regeneration. This technique uses computer assisted design and manufacturing after CT scan. After 3D modelling, individualized scaffolds are printed by extrusion, selective laser sintering, stereolithography, or powder bed inkjet printing. These scaffolds can be made of one or several materials such as natural polymers, synthetic polymers, or bioceramics. They can be monophasic or multiphasic and tend to recreate the architectural structure of the periodontal tissue. In order to enhance the bioactivity and have a higher regeneration, the scaffolds can be embedded with stem cells and/or growth factors. This new technique could enhance a complete periodontal regeneration. This review summarizes the application of 3D printed scaffolds in periodontal regeneration. The process, the materials and designs, the key advantages and prospects of 3D bioprinting are highlighted, providing new ideas for tissue regeneration.

The post-2007 crisis-induced an agricultural expansion across Africa, but local level production and marketing experiences remain understudied. This study assesses the dynamics of agricultural expansion and small-scale farmers’ experiences in rural Zambia. Using a mixed research design, data were drawn from surveys, multi-level interviews, group discussions policy reviews and observations. Results show an agriculture expansion among small-scale farmers is underway due to favourable climatic conditions, land, and water availability, enabled by state subsidies, and an emerging market in commercial and supermarket outlets. However, farmers encounter production and marketing challenges related to poor tenure security, late delivery of inputs, and low financing. They face low and fluctuating prices, poor infrastructure, including low levels of mechanisation necessary to expand the production. Overall, despite an agricultural and land-use expansion taking shape, actual benefits for real transformation are largely missing – and currently over their heads. An argument is made that whilst policy actors continue to impress farmers to organise themselves to maximise benefits of an agricultural expansion, actual processes on how farmers can achieve this are missing in policy and practice. This necessitates a focus on multi-level processes aimed at addressing production, storage and marketing dynamics within a progressive coordination arrangement that centralizes small producers. Until that is addressed, the prospects for local development and poverty reduction for small-scale farmers under an agricultural expansion will be slender but continue to centrally reside in the state efforts to create enabling local and community environment that addresses real challenges. Overall, this study helps to extend the debate on diverse processes shaping rural transformation in Zambia and across sub-Saharan Africa, including the role and importance of agricultural expansion.

Inexpensive piezoelectric diaphragms can be used as sensors to facilitate both nozzle height setting and build platform leveling in FFF (Fused Filament Fabrication) 3D printers. Tests simulating nozzle contact are conducted to establish the available output and an output of greater than 8 Volts found at 20 ºC, a value which is readily detectable by simple electronic circuits. Tests are also conducted at a temperature of 80 ºC and, despite a reduction of greater than 80% in output voltage, this is still detectable. The reliability of piezoelectric diaphragms is investigated by mechanically stressing samples over 100,000 cycles at both 20 ºC and 80 ºC and little loss of output over the test duration is found. The development of a nozzle contact sensor using a single piezoelectric diaphragm is described.

The multifarious internal workings of organisms are difficult to reconcile with a single feature defining a state of ‘being alive’. Indeed, definitions of life rely on emergent properties (growth, capacity to evolve, agency) only symptomatic of intrinsic functioning. Empirical studies demonstrate that biomolecules including ratcheting/rotating enzymes, ribozymes and pigment molecules undergo repetitive conformation state changes driven by energy absorption, excitation and relaxation. They exhibit disparate structures, but govern processes relying on directional physical motion (DNA transcription, translation, ATP synthesis, cytoskeleton transport, photosynthetic resonance energy transfer) and share the principle of repetitive uniplanar conformation changes driven by thermodynamic gradients, producing dependable unidirectional motion: ‘heat engines’ exploiting thermodynamic disequilibria to perform work. Recognition that disparate biological molecules share a heat engine principle governing directional motion, working in self-regulating networks, allows a mechanistic definition: life is a self-regulating process whereby matter undergoes cyclic, uniplanar conformation state changes that convert thermodynamic disequilibria into directed motion, performing work that locally reduces entropy. ‘Living things’ are structures including autonomous networks of units operating on the heat engine principle. Death is loss of integrated heat engine function. These principles are independent of any specific chemical environment, and can be applied to other biospheres.

The metal chelator PBT2 (5,7-dichloro-2-[(dimethylamino)methyl]-8-hydroxyquinoline) acts as a terdentate ligand capable of forming binary and ternary Cu2+ complexes. It was clinically trialed as an Alzheimer’s disease (AD) therapeutic but failed to progress beyond phase II. The β-amyloid (Aβ) peptide associated with AD was recently concluded to form a unique Cu(Aβ) complex that is inaccessible to PBT2. Herein, it is shown that the species ascribed to this binary Cu(Aβ) complex in fact corresponds to ternary Cu(PBT2)NIm[Aβ] complexes formed by anchoring of Cu(PBT2) on imine nitrogen (NIm) donors of His side chains. The primary site of ternary complex formation is His6, having a conditional stepwise formation constant at pH 7.4 (K [M−1] ) of log K = 6.4 ± 0.1, and a second site is supplied by His13 or His14 (log K = 4.4 ± 0.1). The stability of Cu(PBT2)NIm[H13/14] is comparable with that of the simplest ternary complexes involving free imidazole (log K = 4.22 ± 0.09) and histamine (log K = 4.00 ± 0.05). The 100-fold larger formation constant for Cu(PBT2)NIm[H6] indicates that outer-sphere ligand–peptide interactions strongly stabilize its structure. Despite the relatively high stability of Cu(PBT2)NImH6, PBT2 is a promiscuous Cu2+-binding ligand capable of forming a ternary Cu(PBT2)NIm complex with any ligand containing NIm donor. These ligands include histamine, L-His, and ubiquitous His side chains of peptides and proteins in the extracellular milieu, whose combined effect should outweigh that of a single Cu(PBT2)NIm[H6] complex regardless of its stability. We therefore conclude that PBT2 is capable of accessing Cu(Aβ) complexes with high stability but not specificity. The results have implications for future AD therapeutic strategies and understanding the role of PBT2 in the bulk transport of transition metal ions. Given the repurposing of PBT2 as a drug for breaking antibiotic resistance, ternary Cu(PBT2)NIm and analogous Zn(PBT2)NIm complexes may be relevant to its antimicrobial properties.

The aim of this work was to test polyamines as potential natural substrates of the Acinetobacter baumannii chlorhexidine efflux protein AceI using near-UV synchrotron radiation circular dichroism (SRCD) spectroscopy. The Gram-negative bacterium A. Baumannii is a leading cause of hospital-acquired infections and an important foodborne pathogen. A. Baumannii strains are becoming increasingly resistant to antimicrobial agents, including the synthetic antiseptic chlorhexidine. AceI was the founding member of the recently recognised PACE family of bacterial multidrug efflux proteins. Using the plasmid construct pTTQ18-aceI(His₆) containing the A. Baumannii aceI gene directly upstream from a His₆-tag coding sequence, expression of AceI(His₆) was amplified in E. coli BL21(DE3) cells. Near-UV (250-340 nm) SRCD measurements were performed on detergent-solubilised and purified AceI(His₆) at 20 °C. Sample and SRCD experimental conditions were identified that detected binding of the triamine spermidine to AceI(His₆). In a titration with spermidine (0-10 mM) this binding was saturable and fitting of the curve for the change in signal intensity produced an apparent binding affinity (K_D) of 3.97 +/- 0.45 mM. These SRCD results were the first experimental evidence obtained for polyamines as natural substrates of PACE proteins.

Infrared thermography has already been proven to be a significant method in non-destructive evaluation since it gives information with immediacy, rapidity, and low cost. However, the thorniest issue for the wider application of IRT is quantification. In this work, we proposed a specific depth quantifying technique by employing the Gated Recurrent Units (GRU) in composite material samples via pulsed thermography (PT). Finite Element Method (FEM) modeling provides the economic examination of the response pulsed thermography. In this work, Carbon Fiber Reinforced Polymer (CFRP) specimens embedded with flat bottom holes are stimulated by a FEM modeling (COMSOL) with precisely controlled depth and geometrics of the defects. The GRU model automatically quantified the depth of defects presented in the stimulated CFRP material. The proposed method evaluated the accuracy and performance of synthetic CFRP data from FEM for defect depth predictions.

his quantitative study investigates teachers' perceptions of self-efficacy during the COVID-19 pandemic and explores the correlation between these perceptions and the preservice training they received. The research addresses the cognitive connection between teachers' current self-efficacy, particularly their satisfaction with and appreciation of preservice lecturers. Utilizing a retrospective lens, the study reveals a significant correlation between teachers' evaluation of their preservice training, especially their appreciation of lecturers, and their present self-efficacy. The findings highlight that teachers, amidst the challenges of the pandemic, evaluated their self-efficacy at a remarkably high level. This underscores their resilience during a period of unprecedented uncertainty, demanding substantial personal and professional adaptability. The nuanced interplay observed suggests that teachers' sense of self-efficacy serves as a predictive variable of their mental and professional resilience when confronting uncertainty and navigating rapid and profound changes, as exemplified by the exigencies of the COVID-19 pandemic.

As climate change should lead to an increase in the vulnerability and the sensitivity of forests to extreme climatic events, quantifying and predicting their response to more severe droughts remains a key task for foresters. Furthermore, recent works have suggested that tree diversity may affect forest ecosystem functioning, including their response to extreme events. In this study we aimed at testing whether the growth response of forest stands to stressful climatic events varied between mixed and monospecific stands, under various environmental conditions. We focused on beech-fir forests (Fagus sylvatica [L.] and Abies alba [L.]) and beech-oak forests (Fagus sylvatica [L.] and Quercus pubescent [L.]) in the French Alps. We used a dendrochronological dataset sampled in forest plots organized by triplets (one mixture and two monospecific stands) distributed in six sites along a latitudinal gradient. We tested (1) whether stand diversity (two-species stands vs monospecific stands) modulates the stands’ response to drought events in terms of productivity, (2) whether species identity may drive the diversity effect on resistance and recovery, and (3) whether this can be explained by interspecific interactions. We found that (1) interspecific differences in response to extreme drought events (possibly due to interspecific differences in hydraulic characteristics) can induce a mixture effect on stand growth, although it appeared (2) to be strongly depending on species identity (positive effect only found for beech-fir mixed stands), while (3) there were no significant non-additive effects of diversity on stand resistance and recovery, except for some specific cases. Overall, our study shows that promoting selected mixed stands management may buffer extrem drought effect on stand productivity.

The resolution of façade construction is not considered in the design process, as it can be expressed by complex technological innovations that emphasize the beauty of buildings. Nevertheless, resorting to this type of technology solution may not always be necessary. This study demonstrates this hypothesis through the investigation of five iconic case studies emphasizing the construction system analysis and the revelation of the brainwave idea. The brainwave idea defines the construction innovation that enables the detail by simplification rather than sophistication. Notable, unlike complex technological innovation, standard systems or elements applied strategically are considered little innovations to facilitate the resolutions of the façade complexity. Many of these innovations occur during the visual and constructive prototype progress required to validate the proposed solution and its performance. Therefore, real-scale prototype development that operates as a real-scale laboratory is necessary to correct and validate successive solutions.

Overcrowding in the emergency department is a problem that generates several implications for bed management, which is deemed one of a hospital's most critical processes. Effective management of hospital production capacity includes bed management processes, which can be improved in order to leverage hospital performance. Thus, this study sought to understand how bed management works and identify the main factors that influence its management. The study was performed through a case study, with data collected from semi-structured interviews and bibliographic research, which were triangulated. Thematic content analysis of the interviews and cross-analysis were performed. As a result, the main factors that influence hospital Bed management were identified: communication between teams and units; definition of performance goals; decisions shared between units; occupation and discharge planning by the teams; length of stay; the role of the nurses; and COVID-19. The greatest difficulties in the management process are related to these factors. Additionally, suggestions are provided to mitigate such reported difficulties.

In Cameroon, alcoholic beverages remain the main consumed drink. In the Northern regions, indigenous sorghum beers are popular and widely consumed in an actively fermenting state by the people. In this study, some physicochemical parameters of the alcoholic sorghum beverages and correlations between them were evaluated during fermentation for 10 days. The indigenous white and red beers were produced at the laboratory scale assisted by experimented producers and some parameters (pH, total acidity, alcohol, sugars, density, total solids, temperature, and conductivity) were measured on the wort and fermented beverages. The pH decreases from 3.2 to 2.4 and 3.11 to 2.41; total acidity increases from 1.07 to 5.1 g/l and 0.5 to 4.6 g/l; alcohol enhances from 0 to 9.5% and 0 to 6.8% (v/v); total solids drop from 13.6 to 5°P and 12.2 to 3.3°P were observed respectively in the white and red sorghum beers. The multivariate analysis showed a good correlation between consumption of sugar, the decrease of total solids and density with the decrease in pH. It was also shown that, a perfect link exist between the production of alcohol and organic acids. The hierarchical analysis showed that indigenous red beer samples fermented for 1 and 2 days and those fermented for 4 to 10 days are related and could be separate in two distinct groups, whereas white turbid beer samples are separated in three different groups, those fermented for 1 to 4 days, those 5 to 6 days and those 7 to 10 days. The results obtained could serve as a guide to better understand the fermentation process of the indigenous alcoholic sorghum-based beverages.

Additive manufacturing (3D printing) and computer-aided design (CAD) still have limited up-take in biomedical and bioengineering research and education, despite the significant potential of these technologies. The utility of organ-scale 3D-printed models of living structures is widely appreciated, while the workflows for microscopy data translation into tactile-accessible replicas are not well developed yet. Here, we demonstrate an accessible and reproducible CAD-based methodology for generating 3D-printed scalable models of human cells cultured in vitro and imaged using conventional scanning confocal microscopy and fused deposition modelling (FDM) 3D printing. We termed this technology CiTo-3DP (Cells-in-Touch for 3D Printing). As a proof-of-concept, we created CiTo-3DP models of human pancreatic cancer cells and healthy dermal fibroblasts by using selectively stained nuclei and the cytoskeleton components (f-actin and α-smooth muscle actin). The production of dismountable sets of cellular components was al-so shown. The CiTo-3DP approach can be adapted to comprehensively present various cell types, subcellular structures and extracellular matrices. We envisage that the resulting CAD and 3D printed models could be used for further applications, including but not limited to in silico simulations for biology, medicine, pharmacological research, tissue engineering, morphometrical analysis, multiphysics modelling, education, rehabilitation of visually impaired people, and integration into virtual reality.

PdRe/Al2O3 catalysts are highly selective for hydrogenation of furfural to furfuryl alcohol (FAL). Moreover, synergy between the metals can result in greater specific activity (higher turnover frequency, TOF) than exhibited by either metal alone. Bimetallic catalyst structure depends strongly on the metal precursors employed and their addition sequence to the support. In this work, PdRe/Al2O3 catalysts were prepared by: (i) co impregnation (CI) and sequential impregnation (SI) of  Al2O3 using HReO4 and Pd(NO3)2, (ii) SI using NH4ReO4 and [Pd(NH3)4(NO3)2], (iii) HReO4 addition to a reduced and passivated Pd/Al2O3 catalyst, and (iv) impregnation with the double complex salt (DCS), [Pd(NH3)4(ReO4)2]. Raman spectroscopy and temperature-programmed reduction (TPR) evidence larger supported PdO crystallites in catalysts prepared using Pd(NO3)2 than [Pd(NH3)4(NO3)2]. Surface [ReO4]- species detected by Raman exhibit TPR peak temperatures from ranging 85 to 260°C (versus 375°C for Re/Al2O3). After H2 reduction at 400°C, the catalysts were characterized by chemisorption, temperature-programmed hydride decomposition (TPHD), CO diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS), and scanning transmission electron microscopy (STEM) with energy-dispersive x-ray (EDX) spectroscopy. The CI catalyst containing supported Pd-Re alloy crystallites had a TOF similar to Pd/Al2O3 but higher (61%) FAL selectivity. In contrast, catalysts prepared by methods (ii-iv) containing supported Pd-Re nanoparticles exhibit higher TOFs and up to 78% FAL selectivity.

Background: The seasonal variation of peptic ulcers is a rhythmic phenomenon reported worldwide, exhibiting diverse patterns and controversies. Unfortunately, it has remained an unresolved mystery for more than 90 years. Numerous studies have found that this phenomenon was closely associated with multiple environmental factors, but the underlying mechanism has never been elucidated. Objectives: This study aims to elucidate the seasonal variation of peptic ulcers and identify the role of environmental factors in the disease. Methods: Based on a recently identified etiology of peptic ulcers, two inverse operations in calculus, differentiation and integration, are iterated to analyze the existing data. First, the fluctuation curve in the seasonal variation is differentiated twice into the monthly incidences caused by multiple individual environmental factors, and the fluctuation curve due to each individual environmental factor is generated separately. Second, the monthly incidences caused by the individual environmental factors are integrated twice to reproduce the fluctuation curves in the seasonal variation of peptic ulcers. Results: The differentiations of the fluctuation curves in the season variation reveal a parallel relationship between the psychological impacts of each individual environmental factor and the monthly incidences of peptic ulcers. The integrations of the monthly incidences caused by 3 environmental factors reproduce the fluctuation curves in 3 representative seasonal patterns of peptic ulcers but make the parallel relationships invisible. Discussion: The parallel relationships revealed a causal role of environmental factors in peptic ulcers, whereas the reproduction of the fluctuation curves elucidated that multiple environmental factors cause the seasonal variation of peptic ulcers by Superposition Mechanism. The regional differences in environmental factors result in the diverse patterns, as well as the controversy questioning the seasonality of peptic ulcers. Significantly, the data analyses exemplify the application of a new concept, Superposition Mechanism, which might be an indispensable methodological complement to life science and medicine.

Background: In 1962, Susser and Stein observed that the mortality rates of peptic ulcers in England and Wales increased markedly in the 1910s, maintained at a high level during the 1910s-1940s, and began to decline steadily since the early 1950s. They termed this epidemic pattern a birth-cohort phenomenon, but its mechanism has never been elucidated. Susser and Stein speculated that the occurrences of extraordinary social environmental factors roughly fit the fluctuations, but the role of environmental factors in peptic ulcers has never been identified. Objectives: This study aims to elucidate the mechanism of the birth-cohort phenomenon of peptic ulcers and identify the role of environmental factors in the disease. Methods: Starting from an etiology identified recently, this study uses the two inverse operations in calculus, differentiation, and integration, to analyze the existing data. First, a fluctuation curve in the birth-cohort phenomenon is differentiated into multiple annual mortality rates caused by individual environmental factors. Second, these annual mortality rates are integrated to reproduce the fluctuation curve in the birth-cohort phenomenon. Results: The differentiation reveals a parallel relationship between the psychological impacts of environmental factors and the mortality rates of peptic ulcers, whereas the integration reproduces a representative fluctuation curve in the birth-cohort phenomenon. The successive occurrences of multiple social environmental factors from the 1910s to 1940s maintained the increase in mortality rates, while the sustained improvements in living environments explained the steady decline of the mortality rates from the early 1950s. Conclusion: The parallel relationship suggests a causal role of environmental factors in peptic ulcers, whereas the reproduction of a representative fluctuation curve indicates that multiple environmental factors caused the birth-cohort phenomenon by Superposition Mechanism. Significantly, this study challenges the current reductionist approach used to study disease in modern medicine by demonstrating the effectiveness of an opposite methodological concept focused on integration.

Defensive behavior is a function of specific survival circuits, the “aversive brain system”, that are thought to be conserved across vertebrates, and involve threat detection and the organization of defensive responses to reduce or eliminate threat. In mammals, these circuits involve amygdalar and hypothalamic subnuclei and midbrain circuits. The increased interest in teleost fishes as model organisms in neuroscience created a demand to understand which brain circuits are involved in defensive behavior. Telencephalic and habenular circuits represent a “forebrain circuit” for threat processing and organization of responses, being important to mounting appropriate coping responses. Specific hypothalamic circuits organize neuroendocrine and neurovegetative outputs, but are the less well-studied in fish. A “midbrain circuit” is represented by projections to interneurons in the optic tectum which mediate fast escape responses via projections to the central gray and/or the brainstem escape network. Threatening stimuli (especially visual stimuli) can bypass the “high road” and directly activate this system, initiating escape responses. Increased attention to these circuits in an evolutionary framework is still needed.

The primary purpose of this article is to present a maturity model dealing with environmental manufacturing processes in a company. First, a theoretical approach is presented where evolution from the first industrial revolution to the present (Industry 4.0.) is outlined with a need to implement environmental initiatives. Chapter two contains a detailed literature review, which resulted in the creation of our own maturity model presented in the next chapter. According to some authors, Industry 4.0 is based on characteristics that have already been the focus of “lean and green” concepts. The practical part of the article is a case study that shows which areas of the manufacturing process have “environmental” potential. The goal was to move from resource consumption, pollutant emissions and more extensive manufacturing towards environmentally responsible manufacturing (ERM). Using environmental materials and methods reduces energy consumption, which generates cost savings and higher profits. Here, VSM (Value Stream Mapping) was applied to identify core processes with environmental potential. The final part of the article summarizes the work and presents future possibilities. This paper provides an understanding of the role of environmental manufacturing in the era of the 4th industrial revolution.

The research paper investigates the synthesis of metal matrix composites (MMCs) through the amalgamation of aluminum and silicon carbide particles, employing a two-step mixing methodology called the stir casting method. Metal matrix composites are materials that enhance the capabilities of a metallic matrix by incorporating another material. This leads to better characteristics such as tensile and shear moduli, fatigue and fracture properties, thermal expansion coefficient, and more. Aluminum-matrix composites are a class of materials that possess distinct characteristics that may be modified by altering factors such as the type of reinforcing material, the amount of reinforcement, and the fabrication technique employed to produce the composite. The concept aims to combine the desirable properties of metals and ceramics by incorporating durable refractory particles into a malleable metal structure. The fabrication process employs the stir casting technique, where reinforcing phases are mechanically stirred into a molten matrix to create cast composites with reinforcement volume percentages of up to 30%. The study utilizes Response Surface Methodology to enhance the mechanical properties of the composites through the optimization of manufacturing parameters, including stirring temperature, time, and speed. The study entails analyzing the correlation between different casting conditions and the resulting changes in hardness and tensile strength.

Background Gingivitis can develop without mechanical cleaning within three weeks. The first clinical sign is bleeding on positive probing. The accumulation of dental biofilm generates an inflammatory gingival response. In the past decade, attention has focused mainly on the interproximal areas and the use of customsized interproximal toothbrushes.The aim of the study was to evaluate the effectiveness of individualized oral hygiene education and its role in dental prevention among patients with dental problems. Methods Before treatment, patients were clinically and radiologically examined, full mouth plaque score (FMPS), full mouth bleeding score (FMBS), and bleeding on brushing (BOB) were recorded, and matrix-metalloproteinase-8 (MMP-8) was measured by using a chair-side MMP-8 measuring system. Patients in group A had gingivitis, but no periodontal damage and patients in group B had periodontal damage. Patients in both groups A and B were identified in to four subgroups based on their toothbrushing habits and the oral health education they received. The three months after initial examination, each patient was examined three more times (2, 4 and 12 weeks later). Results It was concluded that subjects in groups A1 and B1 showed significant reduction in BOB, MMP-8, FMBS and FMPS levels after two weeks. Solo Prophylaxis (A1and B1) remained as a well-constructed protocol with hte complete resolution of interdental inflammation after two weeks. Other subgroups achieved significant reductions only after 12 weeks. Conclusions BOB and MMP-8 are valuable complements in preventive dentistry, and are able to detect potential pathological processes in interproximal spaces. The clinical relevance of BOB, in addition to FMBS, FMPS and gingival inflammation can be demonstrated to patients, which may increase compliance.

Since it was proposed, the Robot Operating System (ROS) has fostered solutions for various problems in robotics in the form of ROS packages. One of these problems is Simultaneous Localization and Mapping (SLAM), a problem solved by computing the robot pose and a map of its environment of operation at the same time. The increasingly availability of robot kits ready to be programmed and also of RGB-D sensors often pose the question of which SLAM package should be used given the application requirements. When the SLAM subsystem must deliver estimates for robot navigation, as is the case of applications involving autonomous navigation, this question is even more relevant. This work introduces an experimental analysis of GMapping and RTAB-Map, two ROS compatible SLAM packages, regarding their SLAM accuracy, quality of produced maps and use of produced maps in navigation tasks. Our analysis aims ground robots equipped with RGB-D sensors for indoor environments and is supported by experiments conducted on datasets from simulation, benchmarks and from our own robot.

Futures markets are mainly used as a tool for price discovery and for risk management on the spot markets and enable diversification for international portfolio investments. With this study we aim (1) to investigate the causality relationship between futures markets and spot market and (2) to examine the causality relationship between futures markets and spot markets in different countries. We are interested in both the futures markets - spot market relations and the interactions between the markets at international level. For variables we used the the BIST30 spot index and BIST30 futures contract representing the Borsa Istanbul market and the Dow-Jones 30 index and Dow-Jones 30 futures contract, which are the most important indices representing the US markets. Daily closing price data for the period between 2nd January, 2009 and 18th June, 2018 were analyzed using correlation, unit root test, causality test and regression equations. The results of the study show that the futures markets continue their price discovery role for both the spot markets and futures markets and are influential on other futures and spot markets at international level. These findings are important for investors wanting to invest in Turkey and in similarly considered emerging market economies. It will help investors take informed decisions by providing them with a more efficient price estimations utilizing the futures markets.

Many applications in the context of Industry 4.0 require precise localization. However, indoor localization remains an open problem, especially in complex environments such as industrial environments. In recent years, we have seen the emergence of Ultra WideBand (UWB) localization systems. The aim of this article is to evaluate the performance of a UWB system to estimate the position of a person moving in an indoor environment. To do so, we implemented an experimental protocol to evaluate the accuracy of the UWB system both statically and dynamically. The UWB system is compared to a ground truth obtained by a motion capture system with a millimetric accuracy.

The authors argue that despite significant numbers of foreign workers present in the Russian labor market Russia remains unattractive for highly skilled foreign workers. The economic crisis the country has faced since 2014 has resulted in a further outflow of foreign nationals from OECD countries. So Russia has to look for employees among newcomers from the former Soviet states, the majority of whom come from Central Asia. Russian politics with regard to immigration is characterized by the collision between “geopolitical” and domestic policy rationales. On one hand, seeking to maximize its influence in the post-Soviet space Russia provides preferential conditions of employment for citizens of partner countries in the framework of the Eurasian Economic Union. On the other hand, the Kremlin is afraid to liberalize its approach to immigration and the integration of immigrants through fear of losing popularity among the electorate. The second substantial feature of Russian immigration politics is an extreme level of securitization of migration issues. The government considers these issues primarily through a policing lens. One cannot claim that the Russian state does not take any steps to liberalize “migratory regulation”; however, the effect of these measures is being vastly reduced by new restrictions. In addition, liberally designed laws do not bring the expected results due to the corrupt practices that pervade the whole of migration regulation.

This research investigated the significance of learning dispositif (LD) and emotional attachment (EA) on perceived learning success (LS) across a diaspora of Western, Russian, Asian, Middle Eastern and Chinese student cohorts. Foucault’s LD captures the disparate socio-cultural contexts, institutional milieus and more or less didactic teaching styles that moderate learning. EA is a multi-dimensional notion involving affective bonds that emerged in child psychology and spread to marketing and other fields. The sequential explanatory research reviewed the learning and EA literatures and generated an LD–EA framework to structure the quantitative phase of its mixed investigations. In 2017 and 2018, the research collected 150 responses and used a range of statistical techniques for quantitative analysis. It found that LS varied significantly across cohorts, intimating that dispositifs influence learning. Nonparametric analysis suggested that EA also influenced learning, but regressions were inconclusive. Exploratory techniques hint at a dynamic mix of emotional or cognitive motivations during the student learning journey, involving structural breaks in student/instructor relationships. Cluster analysis identified distinct student groupings, linked to years of learning. Separately, qualitative analysis of open-ended survey questions and expert interviews intimates that frequent teacher interactions can increase EA. The synthesis of quantitative with qualitative results and pedagogical reflection suggests that LD and EA both influence learning in a complex, dynamic system. The key constituents for EA are Affection, Connection, Social Presence (SP), Teaching Presence (TP) and Flow but student emotional engagement is conditioned by the socio-cultural milieu (LD) and associated factors like relationships and trust. Unlike in the Community of Learning framework, in the EA framework Cognitive Presence (CP) is an outcome of the interaction between these EA constituents, associated factors and the socio-cultural milieu. Finally, whilst awareness of culture and emotions is a useful pedagogical consideration, learning mainstays remain inclusive educational systems that identify student needs and support well-designed programmes. Within these, scaffolded modules should include a variety of engaging learning activities with non-threatening formative and trustworthy summative feedback. We acknowledge some statistical study limitations, but its tentative findings make a useful preliminary contribution

The number of documents published on the Web other languages than English grows every year. As a consequence, it increases the necessity of extracting useful information from different languages, pointing out the importance of researching Open Information Extraction (OIE) techniques. Different OIE methods have been dealing with features from a unique language. On the other hand, few approaches tackle multilingual aspects. In such approaches, multilingual is only treated as an extraction method, which results in low precision due to the use of general rules. Multilingual methods have been applied to a vast amount of problems in Natural Language Processing achieving satisfactory results and demonstrating that knowledge acquisition for a language can be transferred to other languages to improve the quality of the facts extracted. We state that a multilingual approach can enhance OIE methods, being ideal to evaluate and compare OIE systems, and as a consequence, to applying it to the collected facts. In this work, we discuss how the transfer knowledge between languages can increase the acquisition from multilingual approaches. We provide a roadmap of the Multilingual Open IE area concerning the state of the art studies. Additionally, we evaluate the transfer of knowledge to improve the quality of the facts extracted in each language. Moreover, we discuss the importance of a parallel corpus to evaluate and compare multilingual systems.

In cutting processes tool condition affects the quality of the manufactured parts. As such an essential component to prevent unplanned downtime and to assure machining quality is having information about the state of the cutting tool. The primary function of it is to alert the operator that the tool has reached or is reaching a level of ware beyond which behavior is unreliable. In this paper the tool condition is being monitored by analyzing the electric current on the main spindle via an artificial intelligence model utilizing a LSTM neural network. In the current study the tool is monitored while working on a cylindrical raw piece made of AA6013 aluminum alloy with a custom polycrystalline diamond tool, for the purposes of monitoring the ware of these tools. Spindle current characteristics were obtained using external measuring equipment to not influence the operation of the machine included in a larger production line. As a novel approach, an artificial intelligence model based on a LSTM neural network is utilized for the analysis of the spindle current obtained during a manufacturing cycle and assessing the tool ware range in real time. The neural network was designed and trained to notice significant char-acteristics of the captured current signal. The conducted research serves as a proof of concept for use of a LSTM neural network-based model as a method of monitoring the condition of cutting tools.

The 70/30 copper–nickel alloy is mainly used in critical parts with more demanding conditions in marine settings. There is a need for innovative methods that offer fast production and cost-effectiveness to supplement current copper–nickel alloy manufacturing processes. In this study, we employ wire-arc additive manufacturing (WAAM) to fabricate the 70/30 copper–nickel alloy. The as-built microstructure is characterized by columnar grains with prominent dendrites and chemical segregation in the inter-dendritic area. The aspect ratio of the columnar grain increases with increasing travel speed (TS) at the same wire feed speed (WFS). This is in contrast to an equiaxed grain structure with a more random orientation of conventional sample. The sample built with a WFS of 8 m/min, TS of 1000 mm/min, and a track distance of 3.85 mm exhibits superior corrosion properties in the 3.5 wt% NaCl solution compared to the conventional one, as evidenced by a higher film resistance and breakdown potential, along with a lower passive current density of the WAAM sample. The corrosion morphology reveals the critical roles played by the nickel element unevenly distributed between the dendrite core and inter-dendritic area.

Widespread patterns of poor dietary behavior are a key factor causing the increasing prevalence of chronic diseases around the world. Research provides initial insights into the potential of food literacy (FL) to empower individuals to improve their dietary behavior. Yet, studies on FL interventions in working adults are scarce. This study aimed to investigate the short- and long-term effects of a comprehensive 3-week workplace health promotion program (WHPP) on FL and dietary intake (DI) and to examine the association between FL and DI in a sample of 144 German office workers (30.0% female). Using two random intercept mixed linear regression models, we found significant strong improvements for both FL (β = 0.52, p < .0001) and DI (β = 0.63, p < .0001) after the WHPP when compared to baseline. Significant long-term improvements at 18 months where strong for FL (β = 0.55, p < .0001) and small for DI (β = 0.10, p < .0001). FL showed a significant moderate effect on DI across all measurement time points (β = 0.24, p < .0001). Our study fills a gap of long-term findings in the literature on FL interventions, offers insights into underlying mechanisms, and provides recommendations for effective WHPPs.

This study explores the current landscape of social value (SV) research in the construction industry, analyzing global trends and identifying future research directions. Using bibliometric analysis, research published in Elsevier Scopus database from 2013 to 2023 was extracted using the keywords "social value" AND "construction industry." Results indicate a focus on social value indicators, socioeconomic impacts, project management, innovative practices, and cross-sector collaborations. The study also reveals a lack of attention to SV in African countries' construction sectors. By highlighting research areas and identifying gaps, this study contributes to academic literature, suggesting the need for guidelines, particularly in developing countries, and advocating for further research on SV in the built environment and strategies for global social value creation.

Phosphorus (P) is a vital macronutrient crucial for crop productivity. Plants absorb P salts, mainly orthophosphate, from soil, yet the primary P source resides in organic materials. Soil phosphomonoesterases (APases) play a vital role in releasing P from organics via hydrolysis. Acid and alkaline phosphatases are crucial for alleviating P deficiency in plants. In this review focused on agricultural soils, we studied the relationship of biophysicochemical, agricultural management, and climate factors on APases also its connection with crop growth and yields. Our findings indicate a strong linkage between both APases and soil pH, positively influenced by clay content, organic matter, microbial biomass carbon, and nitrogen. Adopting healthy soil practices like balanced organic fertilizer usage, optimal soil water levels, reduced tillage, crop rotation, and using beneficial plant microbes help boost APase activity. However, the connection between APases and crop productivity remains uncertain due to insufficient research in this area. Our review emphasizes the vital need to evaluate the relationship between APases and meso-macrofauna, alongside essential plant nutrients such as potassium, nutrient ratios, and the synergistic effects of various factors. Understanding the rapid, efficient assimilation of P through APases in the plant-soil and/or plant-microbiota ecosystem it can be crucial for crop productivity and yields.

The so-called Born-Huang ansatz is a fundamental tool in the context of ab-initio molecular dynamics, viz., it allows to effectively separate fast and slow degrees of freedom and thus treating electrons and nuclei at different mathematical footings. Here we consider the use of a Born-Huang-like expansion of the three-dimensional time-dependent Schr\"odinger equation to separate transport and confinement degrees of freedom in electron transport problems that involve geometrical constrictions. The resulting scheme consists of an eigenstate problem for the confinement degrees of freedom (in the transverse direction) whose solution constitutes the input for the propagation of a set of coupled one-dimensional equations of motion for the transport degree of freedom (in the longitudinal direction). This technique achieves quantitative accuracy using an order less computational resources than the full dimensional simulation for a prototypical two-dimensional constriction.

Anomaly detection is an active area of research with numerous methods and applications. This survey reviews the state-of-the-art of data-driven anomaly detection techniques and their application to the the aviation domain. After a brief introduction to the main traditional data-driven methods for anomaly detection, we review the recent advances in the area of neural networks, deep learning and temporal-logic based learning. We cover especially unsupervised techniques applicable to time series data because of their relevance to the aviation domain, where the lack of labeled data is the most usual case, and the nature of flight trajectories and sensor data is sequential, or temporal. The advantages and disadvantages of each method are presented in terms of computational efficiency and detection efficacy. The second part of the survey explores the application of anomaly detection techniques to aviation and their contributions to the improvement of the safety and performance of flight operations and aviation systems. As far as we know, some of the presented methods have not yet found an application in the aviation domain. We review applications ranging from the identification of significant operational events in air traffic operations to the prediction of potential aviation system failures for predictive maintenance.

The corrosion behavior of Fe-containing directionally solidified (DS) and centrifugally cast (CC) Al-Si-Cu-Zn alloys with either Co or Ni additions has been investigated. Electrochemical and immersion corrosion methods were used to investigate the corrosion behavior in 0.6 M NaCl after short (1-hour) and long (30-day) exposure periods. The employed solidification methods allowed the production of samples with a wide range of secondary dendrite arm spacing (SDAS) while preserving Si and Fe-containing phases. The 0.5 wt.% Ni and Co additions led to the growth of the AlFeSi(Ni) and AlFeSi(Co) phases, but no binary AlNi nor AlCo intermetallic par-ticles have been generated. Potentiodynamic polarization studies at early exposure revealed an increase in the corrosion potential as the Ni was added for either fast or slow solidified samples. The electrochemical impedance spectroscopy at early exposure demonstrated that the Ni-modified alloy, on the other hand, was associated to smaller charge transfer resistances, in-dicating a reduction in corrosion resistance after short elapsed time into the electrolyte. Howev-er, 30-day immersion tests revealed much lower corrosion rate of the Ni-modified alloy than the other alloys, while the corrosion rates of the Co-modified and non-modified alloys were simi-lar. In the Ni-containing alloy, decreased corrosion rate under long-term corrosion process was attributed to the formation of a thick and dense alumina layer, effectively protecting the surface under such conditions. This work contributes to a better knowledge of the corrosion behavior of Ni- and Co-corrected Al industrial scrap compositions.

As the global demand for water increases, so does the quantity of wastewater requiring treatment. Due to a relatively low carbon footprint, compared with conventional wastewater treatment technologies, anaerobic digestion (AD) was identified in the 1970s as a forerunner in the push for sustainability, when interest in sustainable technologies and renewable energy sources was first sparked. AD technology development ultimately resulted in the discovery of the ‘anaerobic granule’. It is a spontaneously-forming bio-aggregate of microbial cells capable of digesting pollutants and producing methane-rich biogas as a renewable source of bioenergy. The high settling velocity of such granules meant that AD systems could be operated as high-rate treatment processes, because the active, relatively-slow-growing, pollutant-removing biomass would be retained inside, and not washed out of, even bioreactors operated at extremely high volumetric loading rates. In the intervening years the emergence of the anaerobic ammonium oxidising (anammox) granule, aerobic granule, hydrogenic granule, oxygenic photogranule, and many other functionally-specialised granules, has opened new opportunities in wastewater treatment biotechnology. Whilst environmental engineering based around wastewater treatment is still a growing field of research and implementation, the granule (in all forms) is starting to catch the attention of microbial ecologists. It is a self-immobilised biofilm, with many of the properties of ‘conventional’ biofilms formed in Nature. However, as a single entity, a granule represents an entire community of microorganisms, competing or functioning cooperatively or in syntrophy. Together, inside a bioreactor, granules perform side-by-side arguably representing a meta-organism. Granules are gaining traction as the perfect samples for high-throughput studies on fundamental ecological concepts. Granular biofilms can be used to test hypotheses around drivers of diversity, community assembly, biofilm formation and maturation, community expansion and succession, community stress response, among others. This review outlines the history of three of the most influential types of granules: the anaerobic (methanogenic), aerobic and anammox granule. The main biochemical processes found in each type; their primary characteristics; and the typical makeup of the microbial community underpinning the processes are compared. Finally, the adoption of granules as the perfect ‘playground’ for experiments in microbial ecology is reviewed.

Graphene-based Field-Effect Transistors (FETs) integrated with microstrip patch antennas offer a promising approach for Terahertz signal radiation. In this study, a dual-stage simulation methodology is employed to comprehensively investigate the device’s performance. The initial stage, executed in MATLAB, delves into charge transport dynamics within a FET under asymmetric boundary conditions, employing hydrodynamic equations for electron transport in the graphene channel. Electromagnetic field interactions are modeled via Finite-Difference Time-Domain (FDTD) techniques. The second stage, conducted in COMSOL Multiphysics, focuses on the microstrip patch antenna’s radiative characteristics. Notably, analysis of the S11 curve reveals minimal reflections at the FET’s resonant frequency of 1.34672 THz, indicating efficient impedance matching. Examination of the radiation pattern demonstrates the antenna’s favorable directional properties. This research underscores the potential of graphene-based FETs for Terahertz applications, offering tunable impedance matching and high radiation efficiency for future Terahertz devices.

Academic interest in social and human capital is growing significantly. Similarly, their relationship with sustainability is increasing, especially compared to sustainability’s relationship with natural capital and financial and economic capital. Bibliometric and visualization research on these relationships is nonetheless insufficient. This study analyzes the evolution of the literature on natural capital, financial and economic capital, and social and human capital related to sustainability. On the other hand, the study presents a bibliometric analysis on social capital and human capital (SHC) related to sustainability. The article studies 635 references collected from the Web of Science (WoS) Core Collection database and utilizes visualization of similarities (VOS) viewer program to graphically map the material. The analysis involves co-occurrence of keywords, co-citation, and co-authorship. The results reveal not only the state of the art and the leading trends, but also the evolution regarding impact, main journals, documents, topics, authors, institutions, and countries. The study provides researchers and practitioners with a visual and schematic frame of the research on this topic.

In contrast to conventional non-destructive testing (NDT) and non-destructive evaluation (NDE) methodologies, including radiography, ultrasound, and eddy current analysis, the coplanar capacitive sensing technique emerges as a novel and promising avenue within the field. This paper endeavors to elucidate the efficacy of coplanar capacitive sensing, also referred to as capacitive imaging (CI), within the realm of NDT. Leveraging extant scholarly discourse, this review offers a comprehensive and methodical examination of the coplanar capacitive technique, encompassing its fundamental principles, factors influencing sensor efficacy, and diverse applications for defect identification across various NDT domains. Furthermore, this review deliberates on extant challenges and anticipates future trajectories for the technique. The manifold advantages inherent to coplanar capacitive sensing vis-à-vis traditional NDT methodologies not only afford versatility in application but also underscore its potential for pioneering advancements in forthcoming applications.

The relative proportions between nutrients affects the fate of them for metabolic interconversion, storage and turnover or, essentially for energy, in a process of partition modulated by hormonal and metabolic factors. A basic common chow model was used: ST or standard diet, HF high-fat and HP or high-protein had a common substrate. A CF cafeteria-type diet was added for comparison. Rats (female and male) received the diet for 30d. Nutrient intake and body composition were measured. Plasma glucose, lactate, testosterone (T) and estradiol (E2) were measured. Common groups energy intake, was largely based in carbohydrates CH, yielding 6C units, which were fully oxidized or stored as 2C fragments (fatty acids). Lactate (3C) was partially stored as glycerol of TAG. Accrual of 2C far exceeded about ten-fold that of 3C. Amino acid (AA) catabolism yielded 2C, 3C and 4C-5C fragments, the latter acting as Krebs cycle anaplerotic intermediates (KCAI), that facilitated the oxidation of 2C in detriment of TAG accumulation Lactate levels, were related to lactic dehydrogenase activities in muscle and liver. TAG accrual was maximal in CF, quite differently from HF with similar diet lipid proportion. Maximal rates of lipid storage were found in ST (and CF) groups. Females showed a higher ability to oxidize CH and to store less TAG. T increased N and protein deposition, whilst E2 decreased them favoring AA oxidation and the availability of KCAI. In the rat, an effective energy partition scheme requires that about half of the energy is provided by CH (polysaccharide), and needs enough protein to provide KCAI for a smooth 2C oxidation.

Animal welfare assessment protocols are important for identifying welfare problems in conservation programs. This study aimed to develop a baseline welfare protocol for the assessment of welfare in huemul (Hippocamelus bisulcus) in conservation centers. This protocol is based on the Welfare Quality® (WQ) framework for cattle, considering the available literature on the behaviours, ecology, conservation plans, captive management of this species, and welfare assessment protocols for other ungulate species. As a result, the protocol was specifically developed for huemuls and included four principles, 12 criteria, and 23 animal- and resource-based indicators. The 12 criteria of the WQ protocol were reduced to nine, and three new criteria were added because they were both feasible and essential for welfare assessment in captive huemuls. This protocol is mainly intended to identify welfare problems in endangered species in the context of conservation centers (reproduction, rescue, rehabilitation, or treatment centers). Thus, aggregation of different measures to obtain a global score has not been proposed. However, a scoring system that assigns a value on a 0-2 scale (0= No welfare concern; 1= welfare concern; 2= urgent welfare concern) is proposed for each category. Although further research is still needed to fully validate the protocol, this is the first development of a completed protocol for huemul welfare assessment.

Surveillance along the Kenya-Somalia border has been a big challenge that has continuously puzzled the security personnel, due to insurgency of armed militia Al-Shabaab from Somalia , the Kenyan government proposed construction of a barrier wall. This project developed a low cost wireless sensor network surveillance system to be deployed along the Kenya-Somalia border. The research study utilized two PIR sensor for detecting human intrusion, one motion is detected the sensor transmit the data via an Xbee module. Arduino microcontroller was used to process the data collected by the sensor before transmission. The system developed has two units, the Transmitter unit and a User Graphic interface running on Tuna Term software that displays the received data. During testing, the prototype system detected human intrusion, using the Arduino serial monitor the results were displayed before being package for transmission.

Colours act as stimuli capable of inducing physiological and psychological responses, impacting on human life by influencing behaviour, cognition and emotion. Designers frequently draw upon colour association cues in designing products, packaging and marketing materials to exploit the reported human reactions to them. To date, clinicians and foot orthoses manufacturers appear to have given little thought to how the colour of foot orthoses may have impact within the broader context of a biopsychosocial model of healthcare. Here we examine research regarding colour perception and association and provide rationale for how the use of colour in foot orthoses therapy might be better exploited to improve patient outcomes and to form a focus for future research.

The terms 'open' and 'openness' are widely used across the current higher education environment particularly in the areas of repository services and scholarly communications. Open-access licensing and open-source licensing are two prevalent manifestations of open culture within higher education research environments. As theoretical ideals, open-licensing models aim at openness and academic freedom. But operating as they do within the context of global neoliberalism, to what extent are these models constructed by, sustained by, and co-opted by neoliberalism? In this paper, we interrogate the use of open-licensing within scholarly communications and within the larger societal context of neoliberalism. Through synthesis of various sources, we will examine how open access licensing models have been constrained by neoliberal or otherwise corporate agendas, how open access and open scholarship have been reframed within discourses of compliance, how open-source software models and software are co-opted by politico-economic forces, and how the language of 'openness' is widely misused in higher education and repository services circles to drive agendas that run counter to actually increasing openness. We will finish by suggesting ways to resist this trend and use open-licensing models to resist neoliberal agendas in open scholarship.

Chronic myelogenous leukemia (CML) was the first malignancy for which clinical outcome was drastically improved by kinase inhibitor therapy. Kinase inhibitors targeting other well-known oncogenes have been introduced into clinical practice, but none have shown the same magnitude of clinical benefit as ABL1 inhibition in CML. We argue that early detection is an underappreciated, but critically important factor in success of ABL1 inhibitors in treatment of CML. We show that CML provides a window into how many types of cancer may look and behave at an early stage, prior to diagnosis and the development of additional genomic alterations. The remarkable clinical benefits of ABL1 inhibition is likely due to early detection of CML at a stage in which the tumor is driven by single oncogenic alteration which can be successfully controlled by the inhibitor. Thinking of CML as a prototype for effective systemic treatment based on early cancer detection may help to develop strategies for improving treatment for other types of cancer.

In this paper the authors present a method which facilitates computationally efficient parameter estimation of dynamical systems from a continuously growing set of measurement data. It is shown that the proposed method, which utilises Sequential Monte Carlo samplers, is guaranteed to be fully parallelisable (in contrast to Markov chain Monte Carlo methods) and can be applied to a wide variety of scenarios within structural dynamics. Its ability to allow convergence of one's parameter estimates, as more data is analysed, sets it apart from other sequential methods (such as the particle filter).

This paper aims to describe the geometrical structure and explicit expressions of family of finitely parametrized probability densities over smooth manifold $M$. The geometry of family of probability densities on $M$ are inherited from probability densities on Euclidean spaces $\left\{U_\alpha \right\}$ via bundle morphisms, induced by an orientation-preserving diffeomorphisms $\rho_\alpha:U_\alpha \rightarrow M$. Current literature inherits densities on $M$ from tangent spaces via Riemannian exponential map $\exp: T_x M \rightarrow M$; densities on $M$ are defined locally on region where the exponential map is a diffeomorphism. We generalize this approach with an arbitrary orientation-preserving bundle morphism; we show that the dualistic geometry of family of densities on $U_\alpha$ can be inherited to family of densities on $M$. Furthermore, we provide explicit expressions for parametrized probability densities on $\rho_\alpha(U_\alpha) \subset M$. Finally, using the component densities on $\rho_\alpha(U_\alpha)$, we construct parametrized mixture densities on totally bounded subsets of $M$. We provide a description of inherited mixture product dualistic geometry of the family of mixture densities.

This paper builds on previous work introducing the Secure Remote Update Protocol (SRUP)—a secure communications protocol for Command & Control applications in the Internet of Things, built on top of MQTT. This paper builds on the original protocol, and introduces a number of additional message types: adding additional capabilities to the protocol. We also discuss the difficulty of proving that a physical device has an identity corresponding with a logical device on the network, and propose a mechanism to overcome this within the protocol.

Friction stir welding (FSW) is a solid state welding process for joining metallic alloys and dissimilar metals. It has emerged as an alternative technology for welding high strength alloys that are difficult to join with conventional techniques. FSW is used to produce products with better mechanical properties. Now a days aluminum alloys have been widely used in several industrial applications such as aerospace, marine, automobile and commercial applications due to their light weight structure, better mechanical properties and high corrosion resistance.In this work, three welding parameters such as spindle speed, welding speed and plunge depth were considered for friction stir welding. FSW was carried out between dissimilar aluminum alloy plates (AA6061 and AA 8011) to produce butt joint.A Box-Behnken design with three factors and three levels was chosen to minimize the number of experimental conditions .The tensile strength and hardness of the welded regions were evaluated. The optimum level settings and the major parameters that influence the joint strength were obtained by Box-Behnken design.

In this paper, we analyze data from the 2012 Encuesta de Integración Social y Salud (Social Integration and Health Survey) of the Instituto Nacional de Estadística (Spanish National Institute of Statistics) to obtain profiles created by combining disability, poverty and social exclusion. We hypothesize that the probability that people will experience social exclusion increases if they have a disability, chronic illness or limitation in conducting everyday activities, and that this probability is greater for women than for men. To conduct our analysis, we constructed a social exclusion model based on a series of social determinants that acts as a dependent variable. In this context, social exclusion is understood to go beyond the concept of financial poverty. We performed bivariate analyses, in which we calculated the Odds Ratios (OR) for certain variables considered to be predictors of social exclusion. We also performed a means comparison test and an ANOVA test to observe differences between individuals with recognized disability and those without. Finally, we conducted logistic regression analysis to determine which vulnerability profiles are most likely to experience a situation of social exclusion. We also discuss the limitations of our study, and suggest areas in, which the relationships between health, social exclusion and disability can be further investigated.

Within this paper, electro-mechanical long-term tests on a thrust bearing are presented. The effects of an additional electrical load on the bearing raceways and the used lubricant are investigated. Chemical and rheological investigations are presented which show the changes in the lubricant. These investigations are compared with the electrical loads and the occurring raceway damage. In addition, a comparison is made with mechanical reference tests. This procedure makes it possible to classify the changes that occur due to the electrical load and to distinguish the effects from each other. The background to these investigations is the increased occurrence of parasitic currents in electric motors, which can lead to damage to machine elements. The phenomena that occur here are new challenges in the development of drive trains.

Data from ocean color (OC) remote sensing are considered a cost-effective tool for the study of biogeochemical processes globally. Satellite-derived chlorophyll, for instance, is considered an Essential Climate Variable since it is helpful in detecting climate change impacts. Google Earth Engine (GEE) is a planetary scale tool for remote sensing data analysis. Along with OC data, such tools allow an unprecedented spatial and temporal scale analysis of water quality monitoring in a way that has never been done before. Although OC data have been routinely collected at medium (~1 km) and more recently at high (~250 m) spatial resolution, only coarse resolution (≥4 km) data are available in GEE, making them unattractive for applications in the coastal regions. Data reprojection is needed prior to making OC data readily available in the GEE. In this paper, we introduce a simple but practical procedure to reproject and ingest OC data into GEE. The procedure is applicable to OC swath (Level-2) data and is easily adaptable to higher-level products. The results showed consistent distributions between swath and reprojected data, building confidence in the introduced framework. The study aims to start a discussion on making high resolution OC data readily available in GEE.

Artisanal goldminers in Ghana are exposed to various levels and forms of health, safety and environmental threats. Without the required legislation and regulations, artisanal miners are responsible for their own health and safety at work. Consequently, understanding the probabilities of self-protection at work by artisanal goldminers is crucial. A cross-sectional survey of 500 artisanal goldminers was conducted to examine the probabilities of personal protective equipment use among artisanal goldminers in Ghana. The data was subjected to both descriptive and inferential statistics. Initial findings showed that personal protective equipment use among artisanal miners was 77.4%. Overall, higher probabilities of personal protective equipment use was observed among artisanal goldminers who work in good health and safety conditions as compared to artisanal miners who work in poor health and safety conditions. Also, personal protective equipment use was more probable among the highly educated artisanal goldminers, miners who regularly go for medical screening and the most experienced miners. Additionally, personal protective equipment use was more probable among artisanal miners who work in non-production departments and miners who work in the medium scale subsector. Inversely, personal protective equipment use was less probable among female artisanal miners and miners who earn more monthly income ($174 and above). To increase self-care and safety consciousness in artisanal mining, there is the need for a national occupational health and safety legislation in Ghana. Also, interventions and health promotion campaigns for better occupational conditions in artisanal mining should target and revise the health and safety related workplace programs and conditions

This comprehensive review delves into the multifaceted aspects of ERK signaling and the intricate mechanisms underlying distinct cellular fates. ERK1 and ERK2 (ERK) govern proliferation, transformation, epithelial-mesenchymal transition, differentiation, senescence, or cell death, con-tingent upon activation strength, duration, and context. The biochemical mechanisms underlying these outcomes are inadequately understood, shaped by signaling feedback and the spatial localization of ERK activation. Generally, ERK activation aligns with the Goldilocks principle in cell fate determination. Excessive or insufficient ERK activity inhibits growth, whereas moderated activation supports proliferation and survival. Unraveling the intricacies of how the degree of ERK activation dictates cell fate requires deciphering mechanisms encompassing protein stability, transcription factors downstream of ERK, and the chromatin landscape.

Single Image Super Resolution (SSIR) is a problem in computer vision where the goal is 1 to create high-resolution images from low-resolution ones. It has important applications in fields 2 such as medical imaging and security surveillance. While traditional methods such as interpolation 3 and reconstruction-based models have been used in the past, deep learning techniques have recently 4 gained attention due to their superior performance and computational efficiency. This article proposes 5 an Autoencoder based Deep Learning Model for SSIR, in particular, a light model that uses fewer 6 parameters without compromising performance. The down-sampling part of the Autoencoder 7 mainly uses 3 by 3 convolution and has no subsampling layers. The up-sampling part uses transpose 8 convolution and residual connections from the down sampling part. The model is trained using a 9 subset of the VILRC ImageNet database. The model is evaluated using quantitative metrics PSNR, 10 SSIM as well as qualitative measures such as perceptual quality. PSNR and SSIM figures as high as 11 76.06 and 0.93 are reported.

Adaptive mechanisms, such as channel hopping and packet replication, are used in low-power wireless networks to deal with the spatial and temporal variations in the link quality, and meet the reliability requirements of industrial applications (i.e., PDR>99%). However, the benefits of such mechanisms are limited and may have a large impact on end-to-end latency and energy consumption. Hence, in this paper we propose using adaptive modulation diversity, which allows to dynamically select different modulations, to improve link reliability. We present three adaptive modulation diversity selection strategies and validate them using the data derived from a real-world deployment using the IEEE 802.15.4g SUN modulations (i.e., SUN-FSK, SUN-OQPSK and SUN-ODFM) in an industrial environment. The results show that by using adaptive modulation diversity it is possible to improve link reliability regardless of node conditions.

The adoption of harmful postures due to a sedentary lifestyle, which involves long periods at work in offices, is a factor that exacerbates musculoskeletal risks. To examine these risks, there are numerous postures analysis methods, such as Rapid Upper Limb Assessment (RULA) and Rapid Office Strain Assessment (ROSA). RULA is a consolidated method to evaluate the exposure of individual workers to ergonomic risk factors associated with upper extremity musculoskeletal disorders. In turn, ROSA is a more recent method that quantifies exposure to risk factors in an office work environment. This research aims to identify whether there is harmony between these two methods, ROSA and RULA. Through applied research, from a qualitative perspective, the scientific procedures adopted were direct observation and ROSA and RULA postural assessment instruments. The study was conducted in the radiology service and focused on the outpatient reception workstation. Results indicated that further investigation must occur to make working conditions changes as soon as possible and that both methods are harmonic. As contributions of the analysis, we have discussed the working conditions and suggested improvements to reduce the risks of musculoskeletal morbidity symptoms. We recommend future studies aimed at measuring the levels of complementarity between these methods by quantitative approaches.

The urgency for a shift towards cleaner and more efficient energy alternatives for power generation is underscored by the escalating demand for energy and the detrimental environmental impacts of conventional fossil fuels. In the case of automotive power, electric vehicles are being adopted in many applications, however, challenges remain such as extended charging periods and limited ranges between charges. Therefore, this research study conducts a techno-economic analysis of renewable energy technologies (including solar modules, wind turbines and piezoelectric materials) to augment the efficiency and sustainability of electric buses. The study examines the scope for these technologies to be adopted on double-decker electric buses in London in the United Kingdom. The solar modules are placed on the rooftop and sides of the bus generating 15.9 kWh/day and the wind turbine in the front bumper of the bus generates 8.3 kWh/day. However, the piezoelectric material generated only 22.6 Wh/day, rendering it an impractical inclusion in further analysis. Therefore, both the solar modules and wind turbines combined generate 24.2 kWh/day, which can increase the driving range by 16.3 km per day and this results in savings of 19.36 minutes for charging at the stations. Investing in such projects would have a positive return as the internal rate of return (IRR) and net present value (NPV) are 2.8% and £11,175 respectively. The annual revenue would be £6,712, and the greenhouse gas (GHG) reduction would be two metric tons annually. Electricity exported to the grid, the electricity export rate, and the initial investment are identified as key factors influencing power outage in a sensitivity analysis. In conclusion, this numerical modelling study paves the way for experimental validation towards implementation of renewable energy technologies on electric bus fleets.

This research is a preliminary phase of a general effort to develop a generic-data transferring capability via human haptic thermal sensation (generic-data refers to a coded language like Morse or Braille). For the capability to be effective, it must include a large variety of short recognizable cues. Hence, we propose the concept of cues based on sequences of thermal pulses, i.e., combinations of warm and cool pulses with several levels of intensity. The objective of this study was to determine the feasibility of basing a generic-data-transfer capability on thermal cues composed of sequences of short pulses. The research included defining the basic characteristics of the stimuli parameters and developing practical methods for generating and measuring them. Several sequences were designed in light of the relevant data known to date, and tests were conducted. The thermal cues presented to the participants were sensed and recognized by touch. The results indicate high feasibility for a capability that is applicable in various scenarios. In addition, the low impact on human skin temperature due to short stimuli duration represents an inherent advantage for later implementation. This report presents promising findings and offers insights for further investigation.

The theory of heterogeneous nucleation was initially developed as a part of condensed matter physics and later it was used as an important engineering tool to design metallurgical processes. The success leads to wide applications of the theory in metallurgical practice. For example, engineering heterogeneous nucleation in ductile iron has been used to reduce shrinkage defects, suppress cementite formation, and modify size and shape of micro-structural constituencies. This demonstrates how theoretical knowledge could benefit industry practice. This overview aims to summarize the authors’ published studies in co-authorship with colleagues and students, which covered different aspects of engineering heterogeneous nucleation in multiphase cast alloys. Several approaches for engineering heterogeneous nucleation using thermodynamic simulation and practical methods for improving efficiency of nucleation using co-precipitation technique and a local transient melt supersaturation were suggested. Automated Scanning Electron Microscopy Energy-Dispersive-X-ray (SEM/EDX) analysis and a high-resolution Transmission Electron Microscopy (TEM) were used to verify simulation predictions. Practical examples of controlling micro-porosity shrinkage in cast irons with spheroidal graphite are presented to illustrate the power of engineering heterogenous nucleation. The authors appreciate the great efforts that the co-authors have made on the original, overviewed articles here.

1) Background: It has been more than a decade since the concern about addictive use of the Internet and mobile phones was first expressed and its possible inclusion into the lists of mental disorders has been a popular topic of discussion recently, thus it seems to be a fitting moment to investigate the evolution of this issue over time. The aim of the present study was to analyze the evolution of the perception of problematic Internet and smartphone use in young people over the period 2006–2017; 2) Methods: To this end, a questionnaire on Internet use habits and the CERI and CERM questionnaires on negative consequences of Internet and smartphone use were administered to a sample of 792 university students and compared with data from former studies over the period 2006–2017; 3) Results: The perception of problematic Internet and mobile phone use has increased over the last decade, social networks are considered responsible for this increase, and females are the ones perceived to be more affected than males. The degree to which participants agree with the statement “I am addicted to the Internet” can be used as a screening item for problematic use.

The vehicular ad hoc network (VANET) when augmented with internet is called internet of vehicles (IoV). In the IoV, vehicles have on board units (OBUs), use communication technologies and customized software to communicate with infrastructure around them. The vehicles can have permanent connectivity and global network awareness based on cloud computing. IoV technologies are still being assessed to ensure that the network is protected from attacks, supports a dynamic vehicular mobility scenarios and meets the low latency communication requirements between the vehicles and the surrounding infrastructure. To meet these strict Quality of Service (QoS) demands, Unmanned Aerial Vehicles (UAVs) play a vital role in IoV ecosystems. An UAV can serve as a mobile roadside unit (mRSU) to transmit data between vehicles, stationery RSUs and other UAVs. The UAVs have better line of sight (LOS) connections which result in better channel states and lower path loss than fixed RSUs. Although the inclusion of UAVs in vehicular networks has improved the system performance by providing better resource management and routing solutions, the traditional optimization techniques with their limitations are often not applicable. Therefore, in recent years, research community is integrating Artificial Intelligence (AI) and Machine Learning (ML) into UAV based IoV ecosystem to better manage resource allocation, routing and mobility management issues to optimize the overall network performance. In this survey paper we review the existing research done in AI/ML based UAV-IoV networks and communications with focus on resource management and routing from year 2019 to 2023. We have studied different AI techniques, their training attributes and architectures in various research works. The limitations of AI-based approaches in terms of required computational resources, availability of real world data and AI models’ complexity for the UAV-IoV environment are also discussed. Finally, the future directions for UAV-IoV research opportunities that can leverage the full potential of AI are presented.

In the context of freshwater ecosystems, turbidity and suspended solids play crucial roles, with their levels significantly influenced by anthropogenic activities. This study focuses on assessing and monitoring these parameters in Albufera de Valencia using Sentinel-2 imagery. The primary aim is to establish reliable estimation algorithms that can contribute to effective ecosystem management. The study calibrated and validated algorithms for estimating turbidity and suspended solids. The R783×R705/R490 model proved to have the best performance for estimating turbidity and total solids in the Albufera. However, R783/R490 obtained a higher coefficient of de-termination for the organic part, while the R705 band was selected for the inorganic part. However, to achieve better estimates of turbidity and inorganic matter, more research is needed in the future. The implications of excessive suspended solids are underscored, including the depletion of dissolved oxygen, and reduced primary productivity due to limited light penetration and habitat availability. Collaboration between disciplines such as limnology, optics and water chemistry are crucial to advance water quality estimation models in lakes and lagoons such as Albufera. By integrating expertise and approaches from these diverse fields, new knowledge can be gained and the basis for more effective management and conservation strategies can be laid.

Globally, the need for sustainable urban development has never been more urgent than now. This is because estimates indicate that more than half of the global population will be living in urban areas by 2050, with South Africa estimated at 80%. This paper focuses on socio-economic nuances that impede sustainable urban development, as well as the strategies that can accelerate sustainable urban development in South Africa. Through a literature review methodology, the analysis identified the following issues as impediments to sustainable urban development in South Africa, informal settlements and businesses, lack of consultations with urban citizens, unresolved apartheid legacies, violence, crime and insecurity, and migration and immigration intricacies in South Africa. The paper also established the strategies to accelerate sustainable urban development as working with informality and against it, promoting inclusivity and access to resources, formulating, and accelerating policy reforms, investing in rural areas and towns, and finally investing in superior technology and innovation. These findings imply that there is a need to seek alternative development models and approaches, to address social challenges such as poverty, unemployment, and poor housing, aspects that impact negatively on urban development planning and sustainable development. This is because the major challenges to sustainable urban development are human-related challenges, that need social and economic solutions. There is also a need to reduce rural-urban migration by developing rural towns to ease pressure in major towns which are already spilling over.

Deformation flows are flows incorporating shear, strain and rotational components. These flows are ubiquitous in the geophysical flows, such as the ocean and atmosphere. They appear near almost any salience, such as isolated coherent structures (vortices and jets), various fixed obstacles (submerged obstacles, continental boundaries). Fluid structures subject to such deformation flows may exhibit drastic changes in motion. In this review paper, we focus on the motion of a small number of coherent vortices embedded in deformation flows. Problems involving isolated one and two vortices are addressed. When considering a single-vortex problem, the main focus is on the evolution of the vortex boundary and its influence on the passive scalar motion. Two vortex problems are addressed with the use of point vortex models, and the resulting stirring patterns of neighbouring scalars are studied by a combination of numerical and analytical methods from the dynamical system theory. Many dynamical effects are reviewed with emphasis on the emergence of chaotic motion of the vortex phase trajectories and the scalars in their immediate vicinity.

Identification of plants is a challenging task which aims to identify the family, genus, and species level according to morphological features. Automated deep learning-based computer vision algorithms are widely used for identifying plants and can help users to narrow down the possibilities. However, numerous morphological similarities between and within species make the classification difficult. In this paper, we tested a custom convolution neural network (CNN) and vision transformer (ViT) based models using the PyTorch framework to classify plants. We used a large dataset of 88K and 16K images for classifying plants at genus and species levels respectively. Our results show that for classifying plants at the genus level, ViT models perform better compared to CNN-based models ResNet50 and ResNet-RS-420, and other state-of-the-art CNN-based models suggested in previous studies on a similar dataset. The ViT model achieved top accuracy of 83.3% for classifying plants at the genus level. ViT models also perform better for classifying plants at the species level compared to CNN-based models ResNet50 and ResNet-RS-420, with a top accuracy of 92.5%. We show that the correct set of augmentation techniques plays an important role in classification success.

The purpose of this project was to demonstrate the potential of converting an existing internal combustion engine for hydrogen operation at relatively low cost and to optimize the combustion process for ultra-low NOx emissions. The conversion has been carried out on a 450cc naturally aspirated single cylinder engine. The first baseline measurements and setup have shown lower NOx emissions than the baseline gasoline engine (without catalytic converter) for similar power output and engine efficiency. Further optimization of the combustion process allowed to achieve Euro VI and (latest European Commission proposal) Euro VII heavy-duty NOx limits without exhaust gas aftertreatment system (EATS) in steady state conditions. The concept is very promising and the knowledge gained should allow for further optimization to achieve near zero NOx emissions at high engine efficiency and power output with supercharging. It should also allow an efficient conversion of other engine types for different applications. In particular, a project with the aim to convert a heavy duty 6 cylinder engine intended for public transport buses has started. It follows a feasibility study which has shown the competitiveness of the hydrogen engine for this application.

Renewable energy sources are increasingly crucial for meeting global energy demands in an eco-friendly manner, particularly as the world shifts away from fossil fuels and faces higher volatility of the market prices. Portugal, a country with limited fossil fuel reserves and high energy dependency, has heavily invested in renewables in recent years. However, renewables like sunlight, wind, and water are inherently unsteady due to climate influences, resulting in energy production fluctuations. To mitigate this issue, energy storage systems are being deployed to stabilize renewable energy supply during production lulls. This project aims to assess an energy storage system and define technical specification in order to maximize profitability at the Finerge-owned Alto Douro wind farm. To achieve this, we've conducted an energy demand analysis, followed by simulations to assess system performance in relation to energy use and profit, while varying parameters such as power and efficiency. We've also compared commercial proposals from different battery manufacturers utilizing various technologies. Our findings suggest that high-power, quick charge-discharge lithium-ion batteries are the most suitable solution, given their efficiency and modularity. These attributes are vital for achieving current and future profitability.

Background: The pathogenesis of duodenal ulcer has never been explained although the first description of this disease in medical literature appeared in 1817. Marshall et al. concluded that Helicobacter pylori was the most important etiological factor for duodenal ulcer in 1988, but the etiology based on this bacterium is controversial and how the bacterial infection leads to ulceration is presently unknown. Objectives: This study aims to identify the cause of duodenal ulcer, address the controversial issues surrounding Helicobacter pylori, elucidate the roles of gastric acid, and describe the pathological process of duodenal ulceration. Methods: First, a comprehensive systematic review on peptic ulcers (including gastric ulcer and duodenal ulcer) was conducted and the results were summarized. Second, a recently published causal relationship was employed to identify the etiology of peptic ulcers. Third, novel concepts and methods were applied to analyze the existing data on duodenal ulcer. Results: The etiology of duodenal ulcer and the roles of Helicobacter pylori and gastric acid in this disease were identified. The controversies surrounding Helicobacter pylori were addressed, and many characteristics and phenomena/observations of duodenal ulcer were elucidated. The pathological process of duodenal ulceration was described. Conclusion: Existing data accumulated over the past 300 years was sufficient, when analyzed using novel concepts, to understand the pathogenesis of duodenal ulcer. Duodenal ulcer is not an infectious disease caused by the infection of Helicobacter pylori, but a psychosomatic disease triggered by psychological stress. Helicobacter pylori plays a secondary role in only the late phase of duodenal ulceration.

Pattern recognition techniques form the heart of most, if not all, incoherent linear shift-invariant systems. When an object is recorded using a camera, the object information gets sampled by the point spread function (PSF) of the system, replacing every object point with the PSF in the sensor. The PSF is a sharp Kronecker Delta-like function when the numerical aperture (NA) is large with no aberrations. When the NA is small, and the system has aberrations, the PSF appears blurred. In the above case, if the PSF is known, then the object information can be obtained by scanning the PSF over the recorded object intensity pattern and looking for pattern matching conditions through a mathematical process called correlation. In this study, a recently developed deconvolution method, the Lucy-Richardson-Rosen algorithm (LR2A), has been implemented to computationally refocus images recorded in the presence of spatio-spectral aberrations. The performance of LR2A was compared against the Lucy-Richardson algorithm and non-linear reconstruction. LR2A exhibits a superior deconvolution capability even in extreme cases of spatio-spectral aberrations and blur. Experimental results of deblurring a picture captured using high-resolution smartphone cameras are presented. LR2A was implemented to significantly improve the performances of the widely used deep convolutional neural networks for image classification.

Metabolic syndrome is a growing global health problem. Evidence suggests that diets rich in phytochemical-containing herbs and spices can contribute to reduced risk of chronic disease. This review assesses the scope of evidence supporting the use of herbs and spices in the diet for prevention or treatment of metabolic syndrome and associated health conditions. A search of PubMed and Scopus databases was carried out to assess the available clinical or cohort evidence for culinary doses of commonly used herbs and spices. Trials that were measuring health factors related to metabolic disorders or the health of individuals with metabolic syndrome or associated diseases were included. Out of a total of 1742 papers identified, there were 146 relevant studies on black pepper, chilli, cardamom, cinnamon, coriander, cumin, fennel, fenugreek, garlic, ginger, Nigella seed, rosemary, sage and turmeric. No relevant research was found for cloves, mint, oregano, parsley or thyme. Cinnamon, fenugreek and ginger were the herbs/spices with the most published trials on them and showed promise for glycaemic control. Cardamom appears to have potential to reduce inflammatory markers, and cinnamon, ginger and turmeric for blood lipids. Patients with type 2 diabetes were the population most likely to be included in studies, but the preventative benefits of herbs/spices in healthy populations were also investigated, particularly for chilli, ginger and cinnamon. There is evidence for the beneficial effect of culinary doses of many common herbs/spices in the prevention and treatment of metabolic syndrome and associated disorders.