Classifying network flow subsequences in an Industrial IoT gateway is an effective method for identifying Industrial IoT faults. This paper proposes a subsequence classification algorithm SSGBUL-IKNN based on unsupervised learning encoding to address the problem of low classification accuracy. Firstly, we built a network module based on unsupervised learning to encode the flow sequence of the Industrial IoT gateway. In the encoding module, a subsequence calibration algorithm controls the increasing error during the coding process. Then, the specific fault type is obtained through an improved KNN classification algorithm based on the indication distance source from the integrated coding sequences converted by multi-dimensional network flow sequences. The test result on three Industrial IoT datasets of a sewage treatment plant shows that the accuracy of SSGBUL-IKNN in this paper exceeds 92%, significantly higher than the algorithm DTW and TSF. It reaches the classification requirements of Industrial IoT fault diagnosis.

Decades of research identified numerous gene biomarkers of cardiac diseases whose restored sequence or/and expression level was hoped to recover the normal cardiac function. However, each human has unique and dynamic pathophysiological characteristics resulting from the unrepeatable combination of favoring factors such are: race, sex, age, medical history, diet, stress, exposure to toxins, habits etc. As such, no treatment fits everybody and finding personalized solutions is a top priority for medicine of 21st century. The Genomic Fabric Paradigm (GFP) provides the most theoretically possible comprehensive characterization of the transcriptome, its alterations in disease and recovery following a treatment. By attaching to each gene the independent average expression level, expression variation and expression coordination with each other gene, GFP delivers thousands times more information than the traditional analysis. This report presents the theoretical bases of the GFP and some applications to our microarray data from mouse models of post ischemic, and constant and intermittent hypoxia-induced heart failure. The GFP analyses revealed novel transcriptomic aspects of the gene expression control and networking under ischemic conditions. Through all-inclusive characterization of the transcriptome and the unrepeatable gene hierarchy in each condition, GFP is an essential avenue towards development of a truly personalized cardiogenomic therapy.

The service conditions of underground coal mine equipment are poor, and it is difficult to accurately extract the fault characteristics of rolling bearings. In order to better improve the accuracy of fault identification of rolling bearings, a fault detection method based on multiscale permutation entropy and SOA-SVM is proposed. First, the whale optimization algorithm is used to select the modal analysis number K and the penalty factor α of the variational mode decomposition algorithm. Then, the vibration signal of rolling bearings is dissolved according to the optimized variational mode decomposition algorithm, and the multi-scale permutation entropy of the main intrinsic mode function is calculated. Finally, the feature values of the matrix are entered into the SVM algorithm optimized by the seagull optimization algorithm to obtain the classification result. The experimental results based on the published rolling bearing datasets of Western Reserve University show that the identification success rate of the proposed method can reach 98.75%. The fault detection of the rolling bearings can be completed accurately and efficiently.

Modern power systems are confronted with a spread concern on the frequency stability issue due to the widespread integration of randomly fluctuating renewable resources. To address the above concern, this work introduces a load frequency control (LFC) scheme based on a hydrogen based energy-storage unit and a parameter tuning strategy for fractional-order proportional-integral-derivative (FOPID) controller. Firstly, a two-area interconnected power system (IPS) model, including thermal, hydro, solar, wind, gas power generator, and hydrogen based energy-storage unit, is established. Then, a FOPID controller is designed for this IPS model, and an improved gradient-based optimizer (IGBO) is developed to adaptively regulate the parameters of the FOPID controllers. Finally, the effectiveness of the offered LFC scheme are tested through load disturbance and renewable energy fluctuations test scenarios, and provides comparison and robustness analysis among different schemes. The test results validated that the offered LFC scheme can effectively suppress the frequency fluctuations of IPS and has excellent robustness.

Determining the general-name-derived semantic relationships between geographic names often requires consulting many geographic name documents for verification. In geographic name translation and geographic name knowledge graphs, this method cannot meet the needs of large-scale extraction of general-name-derived semantic relationships between geographic entities. To solve this problem, this paper proposes a general-name derivation relation recognition method based on Prompt learning and Semantic Spatiotemporal Distribution Attention Feature Fusion (SSD-AFF). This method adopts a pipe-based relationship recognition strategy. First, the Prompt learning method is adopted to form a general-name derivation pattern with the general-name-derived geographical name category and the original geographical name category as the prompt word, and then the derivation pattern is combined with the geographical name as the input of the model so that the recognition problem of the general-name derivation of the geographical name can be transformed into a classification problem using the bidirectional language model. Then, by analyzing the characteristics of the semantic association and geographical spatio-temporal distribution between the general-name-derived geographical name and the original geographical name, the semantic spatio-temporal distribution characteristics of the general-name-derived geographical name are constructed. Finally, the network model based on the semantic spatio-temporal distribution Attention Feature Fusion (SSD-AFF) is used to distinguish the general-name-derived semantic relationships. The experimental results show that the proposed method has good performance. It can effectively mine the general-name-derived semantic relations between the vector data of geographical entities and has important application value in geographical name translation and geographical name knowledge maps.

Waxy rice is one of the most popular traditional crops served as a staple food in China. In this study, the effect of different factors including α-amylase activity, protein, and amylopectin structure on the pasting properties of four waxy rice varieties were investigated. Rice flours treated with AgNO3 solution, DL-dithiothreitol (DTT) or protease, suggested that both α-amylase activity and protein significantly decrease the pasting viscosity of waxy rice flours. Chain length distribution of amylopectin as measured by high performance ion exchange chromatography (HPAEC-PAD) showed that starch with higher ratio of short chain leading to a higher pasting viscosity. X-Ray diffractograms showed that the crystal type of all the four varieties of rice starches were characteristic A-type. Relative crystallinity of each rice starch was further calculated, and a higher crystallization resulted in a higher viscosity. Our study would provide a fundamental knowledge of the relationship between different factors and waxy starch pasting properties, as well as be a reference for controlling the quality of waxy rice starch-based food.

Arc sensors have been used in seam tracking and widely studied since the 80s; commercial arc sensing products for T and V shaped grooves have been developed. However, it is difficult to use these arc sensors in narrow gap welding because arc stability and sensing accuracy are not satisfactory. Pulse gas melting arc welding (P-GMAW) has been successfully applied in narrow gap welding and all position welding processes, so it is worthwhile to research P-GMAW arc sensing technology. In this paper, we derived a linear mathematical P-GMAW model for arc sensing, and the assumptions for the model are verified through experiments and finite element methods. Finally, the linear characteristics of the mathematical model were investigated. In torch height changing experiments, uphill experiments, and groove angle changing experiments the P-GMAW arc signals all satisfied the linear rules. In addition, the faster the welding speed, the higher the arc signal sensitivities; the smaller the groove angle, the greater the arc sensitivities. The arc signal variation rate needs to be modified according to the welding power, groove angles, and swing or rotate speed.

Mobility as a Service (MaaS) is an innovative transport concept, anticipated to provide travelers with different kinds of travel services, more sustainable than a private car, in a simpler, packaged way. It combines different transport modes to offer a tailored mobility package, like a monthly mobile phone contract. The rapid development of intelligent transportation system and the shared economy has speeded up the development of MaaS in these years. In this paper, we aim at classifying the existing research on MaaS and the characteristics of MaaS into different categories, in order to answer the following questions after reviewing the existing literature: What is MaaS? Who are the main actors in MaaS? How can MaaS be implemented? Why should it be implemented? Where will MaaS end up in this wave of disruption? When we talk about MaaS, what are we focusing on? What is the future leading frequency of MaaS? Finally, based on the existing literature, we envision the leading future of MaaS.

Amid escalating urbanization, devising rational commercial space layouts is a critical challenge. Leveraging machine learning, this study uses a Back-propagation (BP) neural network to optimize commercial spaces in Weinan City's central urban area. The results indicate an increased number of commercial facilities with a trend of multi-centered agglomeration and outward expansion. Based on these findings, we propose a strategic framework for rational commercial space development emphasizing aggregation centers, development axes, and spatial guidelines. This strategy provides valuable insights for urban planners in small and medium-sized cities in the Yellow River Basin and metropolitan areas, ultimately showcasing the power of machine learning in enhancing urban planning.

The genetic code evolved around the reading of the tRNA anticodon on the primitive ribosome, and tRNA-34 wobble and tRNA-37 modifications coevolved with the code. We posit that EF-Tu, the closing mechanism of the 30S ribosomal subunit, methylation of wobble U34 at the 5-carbon and suppression of wobbling at the tRNA-36 position were partly redundant and overlapping functions that coevolved to establish the code. The genetic code devolved in evolution of mitochondria to reduce the size of the tRNAome (all of the tRNAs of an organism or organelle). “Superwobbling” or four-way wobbling describes a major mechanism for shrinking the mitochondrial tRNAome. In superwobbling, unmodified wobble tRNA-U34 can recognize all four codon wobble bases (A, G, C and U), allowing a single unmodified tRNA-U34 to read a 4-codon box. During code evolution, to suppress superwobbling in 2-codon sectors, U34 modification by methylation at the 5-carbon position appears essential. As expected, at the base of code evolution, tRNA-37 modifications mostly related to the identity of the adjacent tRNA-36 base. TRNA-37 modifications help maintain the translation frame during elongation.

The interfacial polymerization (IP) of piperazine (PIP) and trimesoyl chloride (TMC) has been extensively utilized to synthesize nanofiltration (NF) membranes. However, it is still a huge challenge to monitor the IP reaction, because of the fast reaction rate and the formed ultra-thin film. Herein, two effective strategies were applied to reduce the IP reaction rate: (1) the introduction of hydrophilic interlayers between the porous substrate and the formed polyamide layer, and (2) the addition of macromolecular additives in the aqueous solution of PIP. As a result, in situ Fourier transform infrared (FT-IR) spectroscopy was firstly used to monitor the IP reaction of PIP/TMC with hydrophilic interlayers or macromolecular additives in the aqueous solution of PIP. Moreover, the formed polyamide layer growth on the substrate was studied in a real-time manner. The in situ FTIR experimental results confirmed that the IP reaction rates were effectively suppressed and that the formed polyamide thickness was reduced from 138 ± 24 nm to 46 ± 2 nm according to TEM observation. Furthermore, an optimized NF membrane with excellent performance was consequently obtained, which included boosted water permeation of about 141–238 (L/m²·h·MPa) and superior salt rejection of Na₂SO₄ > 98.4%.

Promoting the sustainable development of resource-based cities is of great significance to the ecological protection and high-quality development of the Yellow River Basin. Combining the environmental status and economic development, we objectively evaluate the ecological safety level of resource-based cities in the Yellow River Basin, compare and analysis the main factors affecting the ecological safety of different resource-based cities, and formulate precise and differentiated ecological safety protection measures in river basins to achieve high-quality development. Taking the Yellow River Basin as an example, this paper analyses the ecological level of the Yellow River Basin based on the theory of sustainable development, calculates the ecological safety level of 30 resource-based cities in the Yellow River Basin from 2006 to 2020 by TOPSIS model, and makes convergence analysis by classification. Through the DID empirical test of sustainable development planning policy on ecological safety factors, distinguish the development characteristics of different resource-based cities. The results show that: (1) the ecological safety level of resource-based cities in the Yellow River Basin is generally developing well, and there are differences among different types of resource-based cities; (2) the kinetic energy of sustainable development of resource-based cities in the Yellow River Basin is mainly industrial transformation, and the power of science and technology is insufficient; (3) local governments pay limited attention to environmental protection, and the sustainable development planning of resource-based cities in 2013 mainly promotes the adjustment of industrial structure of resource-based cities.

The research of object classification and part segmentation is a hot topic in computer vision. A considerable number of studies have been carried out about deep learning on 3D point clouds. However,it is challenging to achieve effective feature learning due to sparsity of point clouds. Recently, a variety of Transformers have been adopted to improve point cloud processing and display great potential. Nevertheless, large numbers of Transformer layers tend to incur huge computational and memory costs. PointNet++ is one of the most influential neural architectures for point cloud understanding. Although the accuracy of PointNet++ has been largely surpassed by recent networks, this does not mean that PointNet++ has no potential.Thus, this paper offer two major contributions that significantly improve PointNet++ performance. Firstly, we introduce a novel contextual feature extraction (CFE) block that significantly enhances the feature extraction capabilities of PointNet++ networks. Secondly, to further enhance feature fusion, we seamlessly integrate a mutual learning (ML) block into the network architecture. By embedding these two innovative blocks within each layer of the network, we not only enrich the network's functionality but also impart it with greater robustness and adaptability. The specific experiments were conducted on the S3DIS (6-fold cross-validation) and Modelnet40 datasets with 86.5% and 92.7% accuracy, respectively, which proved that our model is comparable or even better than most existing methods for classification and segmentation tasks.

Introduction: Novel robotic surgery systems (da Vinci Xi) are superior to classical open and laparoscopic techniques with its clear and three-dimensional view. We aimed to present the first case low anterior resection of rectal cancer and vaginal specimen extraction with Da Vinci Xi.Case: A 75-year-old female patient with rectum adenocarcinoma was undergone robotic-assisted low anterior resection (LAR) of the rectum, vaginal removal of the specimen, colorectal anastomosis and loop ileostomy. The operation time was 190 minutes. There were no postoperative complications. Pathological tumor stage was stage pT1N0 with negative proximal, distal and radial resection margins. The patient was discharged on the third postoperative day.Conclusion: Robot-assisted LAR, total mesorectal excision, vaginal removal of the specimen, colorectal anastomosis, and loop ileostomy can be performed easily and safely with Da Vinci Xi at early stage rectal cancer. And the vaginal extraction of the specimen avoids us from a traditional abdominal incision.

The genetic code evolved by parallel tracks of chaotic and ordered processes. Liquid-liquid phase separation (hydrogels), a chaotic process, constructs diverse membraneless compartments within cells, resulting in regulated hydration and sequestration and concentration of reaction components. Hydrogels relate to chaotic amyloid fiber production. We propose that polyglycine and related hydrogels (i.e. GADV; G is glycine), phase separations, membraneless droplets and amyloid accretions organized protocell domains to drive the earliest evolution of the genetic code and the pre-life to cellular life transition. By contrast, evolution of tRNA, tRNAomes, aminoacyl-tRNA synthetases and translation systems followed highly ordered and systematic pathways, described by well-defined mechanisms and rules. The pathway of evolution of aminoacyl-tRNA synthetases, which tracked evolution of the genetic code, is clarified. Hydrogels and amyloids form a chaotic component, therefore, that complemented otherwise systematic processes. We describe with detail a pre-life world in which hydrogels and amyloids provided the selections of the first life.

The 3 31 nucleotide minihelix tRNA theorem describes evolution of type I and type II tRNAs to the last nucleotide. In databases, type I and type II tRNA V loops (V for variable) were improperly aligned, but alignment based on the theorem is accurate. Type II tRNA V arms were a 3’-acceptor stem (initially CCGCCGC) ligated to a 5’-acceptor stem (initially GCGGCGG). The type II V arm evolved to form a stem-loop-stem. In Archaea, tRNALeu and tRNASer are type II. In Bacteria, tRNALeu, tRNASer and tRNATyr are type II. The positioning of the type II V arm is determined by the number of unpaired bases just 5’ of the Levitt base (Vmax). For Archaea, tRNALeu has 2 unpaired bases, and tRNASer has 1 unpaired base. For Bacteria, tRNATyr has 2 unpaired bases, tRNALeu has 1 unpaired base and tRNASer has 0 unpaired bases. Thus, the number of type II tRNAs is limited by the possible set points of the arm. From analysis of aminoacyl-tRNA synthetase structures, contacts to type II V arms appear to adjust allosteric tension communicated primarily via tRNA to aminoacylating and editing active sites. To enhance allostery, it appears that type II V arm end loop contacts may tend to evolve to V arm stem contacts.

There are no theorems (proven theories) in the biological sciences. We propose that the 3 31 nt minihelix tRNA evolution theorem be universally accepted as one. The 3 31 nt minihelix theorem completely describes evolution of type I and type II tRNAs from ordered precursors (RNA repeats and inverted repeats). Despite diversification of tRNAome sequences, statistical tests overwhelmingly support the theorem. Furthermore, the theorem relates the dominant pathway for the origin of life on Earth, specifically, how tRNAomes and the genetic code may have coevolved. Alternate models for tRNA evolution (i.e., 2 minihelix, convergent and accretion models) are falsified. In the context of the pre-life world, tRNA was a molecule that via mutation could modify anticodon sequences and teach itself to code. We relate the clearest history to date of the chemical evolution of life on Earth. From analysis of tRNA evolution, ribozyme-mediated RNA ligation was a primary driving force in evolution of complexity during the pre-life to life transition on Earth.

Evolutionary, sequence and structural analyses of tRNA variable (V) loops provides a new understanding. Type I tRNA V loops have a primordial length of 5 nt, and type II tRNA V loops have a primordial length of 14 nt. Sequence-based alignments of type I and type II V loops gave deceptive results. Type II V loops are characterized by the trajectory of the V arm, the size and sequence of the loop and the first and last V loop nucleotides and their known contacts. Depending on the V arm trajectory, type II V stems and loops can be interaction sites for aminoacyl-tRNA synthetases. So, type II V arms for tRNALeu, tRNASer and tRNATyr (found in Bacteria) were coevolved and selected to distinguish determinants to support cognate tRNA charging. The alignment of type I and type II V loops was adjusted based on tRNA evolution. Results are consistent with Archaea being an older and simpler life form than Bacteria. TRNAome sequences were derived from radiation of an ordered tRNAPri (Pri for primordial) sequence comprised of known RNA repeats and inverted repeats. V loop and tRNA sequences, therefore, convey a history of the primary successful pathway in the origin of life.

With the rapid development of wind power generations, the inertial response of wind turbines (WTs) are widely concerned recently, which is important for grid frequency dynamic and stability. This paper recognizes and understands the inertial response of type-3 and type-4 WTs from the view of equivalent internal voltage, in analogy with typical synchronous generators (SGs). Due to the dynamic of the equivalent inertial voltage different from SGs, the electromechanical inertia of WTs is completely hidden. The rapid power control loop and synchronization control loop is the main reasons that the WT's inertial response is disenabled. On the basis of the equivalent internal voltage's dynamic, the existing inertia control method for WTs are reviewed and summarized as three approaches from the view of WT's control, i.e. optimizing the power control or synchronization control or both. At last, the main challenges and issues of these inertia controls are attempted to explain and address.

Flavin-dependent monooxygenases (FMOs) have made substantial influence as catalysts for monooxygenation reactions, impacting diverse field such as drug metabolism, environmental studies, and natural product synthesis. Their application in biocatalysis boasts several advantages over conventional chemical catalysis, such as heightened selectivity, safety, sustainability, and eco-friendliness. In the realm of biomedicine, FMOs are pivotal in antibiotic research, modulating natural products, antimicrobial agents, and pathways involved in drug synthesis. They're also underscored as potential pharmaceutical targets, pivotal in disease progression and viable for therapeutic intervention. Additionally, FMOs play a substantial role in environmental science, especially in pesticide processing and plant vitality. Their involvement in biosynthesizing compounds like polyethers, tropolones, and ω-hydroxy fatty acids, with remarkable regio- and stereoselectivity, renders them indispensable in drug discovery and development. As our comprehension of FMOs' catalytic mechanisms and structures advances, coupled with cutting-edge biotechnologies like computational design and directed evolution, FMOs are poised to occupy an increasingly significant role in both scientific exploration and industrial applications.

The AREB/ABF (ABA response element binding) proteins in plants are vital for plant stress responses, but the understanding of AREB/ABFs in orchid species, an important traditional medicinal and ornamental plants, is limited. Here, twelve AREB/ABF genes were identified within three orchids’ complete genome and classified into three groups (groups I, II, and III) via a phylogenetic analysis, which was further supported by the analysis of their conserved motifs and gene structures. The cis-elements analysis showed that hormone response elements followed by light and stress responses were widely rich in AREB/ABFs. A prediction analysis of orchid ABRE/ABF-mediated regulatory network was further constructed through cis-regulatory elements (CREs) analysis of their promoter regions and revealed that several transcriptional factor (TF) gene family were abundant as the potential regulators for orchid AREB/ABFs. Expression profile analysis based on public transcriptomic data showed that most AREB/ABF genes have distinct tissue-specific expression patterns in orchid plants. Additionally, DcaABI5 as the homolog of ABA INSENSITIVE 5 (ABI5) from Arabidopsis was selected for further analysis. The results showed that Arabidopsis transgenic overexpressing DcaABI5 could rescue the ABA insensitive phenotype in the mutant abi5. Collectively, these findings will provide valuable information on AREB/ABF genes in orchids.

Background: Although triptorelin acetate (TA) is generally considered a safe medication, severe adverse drug reactions (ADRs) to triptorelin have occurred. In this study, we present the largest retrospective analysis of ADRs related to TA during the treatment of pediatric central precocious puberty. Methods: We describe a total of 38 suspected cases of TA-induced ADRs reported to the pharma-covigilance center of Shenzhen Children’s Hospital from September 2015 to December 2022. Causality assessment was carried out using the validated Kramer’s algorithm. The severity of ADRs was evaluated using the Modified Hartwig and Siegel Scale. Results: The most common ADRs attributed to TA were damage to the cutaneous tissues (29.3%) and reactions affecting the systemic and digestive systems (20.7%). The majority (61.1%) of ADRs occurred within 2 hours of administration. Among the 12 patients with severe ADRs, the three most frequent symptoms were anaphylactic reactions, hip synovitis, and arthralgia. Additional-ly, six patients experienced ADRs due to a change in the manufacturing process. Conclusion: The majority of ADRs observed in pediatric cases were type I anaphylactic reactions, which are rare but life-threatening. It is advisable to perform skin prick tests and intradermal tests when switching pharmaceutical manufacturers.

Recently, various relations and criteria have been presented to establish a proper relationship between control systems and control Global Positioning System (GPS)-intelligent buoy system. Given the importance of controlling the position of buoys and the construction of intelligent systems, in this paper, dynamic system modeling is applied to position marine buoys through the improved neural network with a backstepping technique. This study aims at developing a novel controller based on adaptive fuzzy neural network to optimally track the dynamically positioned vehicle on water with unavailable velocities and unidentified control parameters. In order to model the network with the proposed technique, uncertainties and the unwanted disturbances are studied in the neural network. The presented study aims at developing a neural controlling which applies the vectorial back-stepping technique to the surface ships, which have been dynamically positioned with undetermined disturbances and ambivalences. Moreover, the objective function is to minimize the output error for the neural network (NN) based on closed-loop system. The most important feature of the proposed model for the positioning buoys is its independence from comparative knowledge or information on the dynamics and the unwanted disturbances of ships. The numerical and obtained consequences demonstrate that the controller system can adjust the routes and the position of the buoys to the desired objective with relatively few position errors.

This paper investigates the dynamic properties of artificial neural networks using differential equations and explores the influence of parameters on stability and neural oscillations. By analyzing the equilibrium point of the differential equations, we identify conditions for asymptotic stability and criteria for oscillation in artificial neural networks. Furthermore, we demonstrate how adjusting synaptic weights between neurons can effectively control stability and oscillation. The proposed model offers potential insights into the malfunctioning mechanisms of biological neural networks implicated in neurological disorders like Parkinson's disease tremors and epilepsy seizures, which are characterized by abnormal oscillations.

A fluorescent probe, N'-((3-methyl-5-oxo-1-phenyl-4, 5-dihydro-1H-pyrazol-4-yl) methylene)-2-oxo-2H-chromene-3-carbohydrazide (MPMC), was synthesized and characterized. Characterizations of the synthetic MPMC were conducted by proton nuclear magnetic resonance (1HNMR) spectroscopy and carbon-13 nuclear magnetic resonance spectroscopy (13C NMR). The fluorescence emission behaviors of probe MPMC towards diverse metal ions were detected and the probe exhibited high sensitivity and selectivity towards Cu2+ over other metal ions via quenching of its fluorescence. Furthermore, the existence of other metal actions made no difference on the fluorescence intensity of the MPMC-Cu2+ system apparently, that is, MPMC displayed a good anti-interference ability. Job’s plot of MPMC and copper ions indicated the detection limit was 15.16 nM (R2=0.9612) for the assayed actions, with a stoichiometric ratio of 1:1 for MPMC and Cu2+. Additionally, the color of MPMC probe solution changed from nearly colorless to yellow in the presence of Cu2+ in visible light, which the color change could be observed by the naked eye. Similarly, the color resolved bright yellow into blue in ultraviolet light. Also reusability studies indicated that MPMC probe was reusable. The pH effect of probe MPMC to Cu2+ had a broad range of pH detection 4.0 to 11.0. The response time of MPMC probe for determining Cu2+ was within 1 min. The recognition of Cu2+ by MPMC performed on pre-treated paper under sunlight and UV light both had a distinct colour change. Thus, the solid-state method for detecting Cu2+ with the naked-eye, was both economical and convenient.

The basic idea is to expand the completed zeta function $\xi(s)$ in MacLaurin series (infinite polynomial), which can be further expressed as infinite product (Hadamard product) by conjugate complex roots. Finally, the functional equation $\xi(s)=\xi(1-s)$ leads to $(s-\alpha_i)^2 = (1-s-\alpha_i)^2, i \in \mathbb{N}$ with solution $\alpha_i= \frac{1}{2}, i \in \mathbb{N}$, where $\alpha_i$ are the real parts of the zeros of $\xi(s)$, i.e., $s_i =\alpha_i\pm j\beta_i, i\in \mathbb{N}$. Therefore, a proof of the Riemann Hypothesis is achieved.

The expansion of concrete subjected to extreme elevated temperature is linked with intricate micro-structural variations, such as the transformation of the constituent phases. This study proposes a model to predict the thermal expansion of cement paste and concrete considering micro-structural changes under elevated temperatures ranging from 20°C to 800°C. The model presented can consider characteristics of various aggregates in the calculation of thermal expansion for concrete. The model is a combination of a multi-scale stoichiometric model and a multi-scale composite model. At the cement paste level, the model satisfactorily predicted a test result. At concrete level, upper bounds from the model were matched relatively well with test results by previous researcher. If the mechanical properties, such as elastic modulus (E), Poisson’s ratio (ν), and thermal deformation, of the aggregates used in concrete are given, it is likely that the model will reasonably predict experimental results.

Manufacturing enterprises are increasingly compelled to pursue innovative solutions to environmental issues. Addressing such issues requires mindful leadership to support employees and organizations in maintaining awareness during complex situations, thereby promoting environmental sustainability. Drawing on social information processing theory, this study theorizes and tests the relationships mindfulness leadership, employee moral reflectiveness, environmental passion, and employee green creativity. To test the model, we utilize a two-wave multi-source dataset comprising 215 workers from manufacturing firms in China. The findings demonstrate that mindful leadership is positively related to employee green creativity. Additionally, our research reveals that both moral reflectiveness and environmental passion serve as mediators in linking mindful leadership to employee green creativity. Crucially, our empirical analysis suggests a serial mediation model, examining the sequential role of moral reflectiveness and environmental passion in the relationship between mindful leadership and employee green creativity. The findings provide a new viewpoint on employees' eco-friendly behaviors and have practical implications for improving environmental sustainability within organizations.

From the mid-19th century, Collegiate Gothic architecture gained prominence among American universities. Subsequently, through the efforts of American missionaries, the Collegiate Gothic style spread to Christian universities in Asia. Specifically, this study concentrates on the nuanced relationship between the transnational missionary routes and adopting the Collegiate Gothic style, primarily focusing on Anderson Hall at Soochow University, China. The investigation meticulously dissects the multifaceted factors influencing the choice of architectural styles, considering the perspectives of missionaries, architects, and other key stakeholders. Through an intricate analysis of Anderson Hall, this research illuminates the unique characteristics of Collegiate Gothic architecture. By unraveling the complex layers of East Asian campus heritage, this study enriches our comprehension of its origins. It establishes a robust foundation for guiding the preservation and revitalization of architectural styles within university campuses. This scholarly inquiry holds particular significance for experts in academic heritage conservation.

Factory safety inspections are crucial for ensuring safe production. However, manual inspections present issues such as low efficiency and high workload. Inspection robots provide an efficient and reliable solution for completing patrol tasks. The development of robot localization and path planning technologies provides guarantees for factory inspection robots to autonomously complete inspection tasks in complex environments. This paper studies mapping and localization, as well as path planning methods for robots in order to meet the application requirements of factory inspections. Two SLAM application systems based on multiple-line laser radar and vision are designed for different scenarios in consideration of the limitations of cameras and laser sensors in terms of their own characteristics and applicability in different environments. To address the issue of low efficiency in inspection tasks, a hybrid path planning algorithm that integrates the A-star algorithm and time elasticity band algorithm is proposed. This algorithm effectively solves the problem of path planning in complex environments that is prone to falling into local optimal solutions, thereby improving the inspection efficiency of robots. Experimental tests show that the designed SLAM and path planning methods can meet the needs of robot inspection in complex scenes and have good reliability and stability. The code used in this article is open source and can be accessed at https://github.com/Mxiii99/RSPP_CS.git.

This paper uses the $\exp(-\Phi(\xi))$-Expansion method to investigate solitons to the M-fractional nonlinear Schrödingers equation with cubic nonlinearity. The results obtained are dark solitons, trigonometric function solutions, hyperbolic solutions and rational solutions. Thus, the constraint relations between the model coefficients and the traveling wave frequency coefficient for the existence of solitons solutions are also derived.

To address three important issues related to extraction of water features from Landsat imagery, i.e., selection of water indexes and classification algorithms for image classification, collection of ground truth data for accuracy assessment, this study applied four sets (ultra-blue, blue, green, and red light based) of water indexes (NWDI, MNDWI, MNDWI2, AWEI_ns, and AWEI_s) combined with three types of image classification methods (zero-water index threshold, Otsu, and kNN) to 24 selected lakes across the globe to extract water features from Landsat-8 OLI imagery. 1440 (4x5x3x24) image classification results were compared with the extracted water features from high resolution Google Earth images with the same (or ±1 day) acquisition dates through computing the Kappa coefficients. Results show the kNN method is better than the Otsu method, and the Otsu method is better than the zero-water index threshold method. If the computational cost is not an issue, the kNN method combined with the ultra-blue light based AWEI_ns is the best method for extracting water features from Landsat imagery because it produced the highest Kappa coefficients. If the computational cost is taken into account, the Otsu method is a good choice. AWEI_ns and AWEI_s are better than NDWI, MNDWI and MNDWI2. AWEI_ns works better than AWEI_s under the Otsu method, and the average rank of the image classification accuracy from high to low is the ultra-blue, blue, green, and red light-based AWEI_ns.

Tourism activities generally have a ∩-type lock on the level of tourism ecological security in an area, but when applied to the border areas of China, there are certain specificities in the spatial evolution of tourism ecological security (TES) compared to traditional findings. This paper measures tourism ecological security in China’s border areas from 2009 to 2020 by using the DPSIR model with the superefficient SBM-DEA and analyzes the spatial differences, evolutionary characteristics, and driving factors of tourism ecological security in border areas by using Pearson’s correlation coefficients, center of gravity models, and geographic probes: (1) The overall tourism ecological security index of China’s border provinces is relatively good. Tourism activities do not completely affect the traditional “∩ lock” of the border provinces. The tourism ecological security level of the border provinces presents three spatial-temporal changes (“∩” type, “U” type, “\” type) and four evolution trends (“high–high–high”, “middle–middle–medium”, “medium–low–low”, and “low–low–low”). (2) The overall tourism ecological security level in border areas is polarized between high and low levels, and the ecological security efficiency of the three large areas is spatially characterized as “Southwest Area > Northeast Area > Northwest Area”, and the center of gravity of ecological security is mostly concentrated in Xinjiang, Tibet, and Neimenggu, where the ecological security level is higher. (3) Social and environmental factors are the main factors that influence tourism ecological security in border areas, while economic factors account for a smaller proportion. Accordingly, this thesis also proposes the driving mechanism of the ecological security of tourism sites in border areas in China with a view to providing theoretical support for policy formulation.

The temperature-dependent energy storage properties of four tungsten bronze phase compounds are studied together with an investigation of their structure and temperature-dependent permittivity response, i.e., Ba6Ti2Nb8O30 (BTN), Ba6Zr2Nb8O30 (BZN), Sr3TiNb4O15 (STN) and Sr3ZrNb4O15 (SZN) ceramics. It was found that BZN has smaller grains and a more porous structure than BTN. SZN shows no clear grain boundaries with the most porous structure among all samples, exhibiting a much lower permittivity response than other samples with no signs of phase transitions from room temperature to 400 °C. Though the energy storage response of those samples is generally quite low, it exhibits rather good temperature stability. It was suggested that by obtaining a denser structure through chemical modification or other methods, those tungsten bronze ceramics with good temperature stability could be promising as energy storage devices when improved energy storage properties are achieved.

Phenology is one of the ubiquitous fingerprints of climate change on our ecosystems. Monitoring the spatiotemporal patterns of vegetation phenology is thus critical. A wide range of sensors have been used to monitor vegetation phenology. Sensor point of view and resolution can potentially impact estimates of phenology. We compared three different sensors from three different remote sensing platforms—a UAV mounted RGB camera, an under canopy, upward facing hemispherical camera with R, G and NIR capabilities, and a tower mounted RGB PhenoCam—to estimate spring phenological transition in a mixed-species temperate forest in central Virginia, USA. Our study had two objectives: 1) to compare the above- and below- canopy inference of canopy greenness (green chromatic coordinate and normalized difference vegetation index) and canopy structural attributes (leaf area and gap fraction) by matching under-canopy hemispherical photos with high spatial resolution (0.03 m) drone imagery to find the appropriate spatial coverage and resolution for comparison; 2) to compare how each sensor performed in estimating the temporality of the spring phenological transition. We find that a spatial buffer of 20 m radius for UAV imagery is most closely comparable to under-canopy imagery in this system. Sensors and platforms agree within +/- 5 days of when canopy greenness stabilizes from the spring phenophase into the growing season. This work has implications for paring UAV imagery with both tower-based observation platforms, as well as plot-based studies (e.g. long-term monitoring, existing research networks, permanent plots).

Brain-stimulation reward, also known as intracranial self-stimulation (ICSS), is a commonly used procedure for studying brain reward function and drug reward. In electrical ICSS, an electrode is surgically implanted into the medial forebrain bundle in the lateral hypothalamus or the ventral tegmental area in the midbrain. Operant lever responding leads to the delivery of electrical pulse stimulation. The alteration in the stimulation frequency-lever response curve is used to evaluate the impact of pharmacological agents on brain reward function. If a test drug induces a leftward or upward shift in the ICSS response curve, it implies a reward-enhancing or abuse-like effect. Conversely, if a drug causes a rightward or downward shift in the functional response curve, it suggests a reward-attenuating or aversive effect. A significant drawback of electrical ICSS is the lack of cellular selectivity in understanding the neural substrates underlying drug reward versus aversion. Excitingly, recent advancements in optical ICSS (oICSS) have facilitated the development of at least three cell type-specific oICSS models – dopamine-, glutamate-, and GABA-dependent oICSS. In these new models, a comparable frequency-rate response curve has been established and employed to study the substrate-specific mechanisms underlying brain reward function and a drug's rewarding versus aversive effects. In this review article, we summarize recent progress in this exciting research area. The findings in these new behavioral models have not only increased our understanding of the neural mechanisms underlying drug reward and addiction but have also introduced a novel experimental approach in preclinical medication development for treating substance use disorders.

Elevated indoor CO2 levels might have adverse effects on human health. However, the introduction of outdoor air to lower indoor CO2 concentrations results in significant HVAC energy consumption. Aligning with office hours and the natural light cycle, the utilization of photosynthesis in living walls offers an energy-efficient and sustainable solution for the mitigation of high CO2 levels in office spaces. This study experimentally investigates the impacts of the carbon fixation pathways, light intensity, and substrate moisture content on the CO2 removal rate of living walls at the room scale. Furthermore, the fresh air energy-saving effects of living walls under different scenarios are accurately simulated in EnergyPlus. The results demonstrate that choosing C3 plants over CAM plants in living walls yields higher CO2 removal efficiency. In a 30-m2 office room accommodating 2-3 occupants, living walls can reduce the demand for fresh air by 12.3%-27.8% and decrease fresh air energy consumption by 11.2%-28.2%. The city with the highest energy savings has energy savings that are 4.5 times greater than those of the city with the lowest energy savings. The findings of this research promote the application and development of living walls, thus providing a viable solution for improving indoor air quality.

Gaze tracking of high-speed moving targets is a novel application mode for low Earth orbit microsatellites. In this mode, small satellites are equipped with high-resolution narrow-field-of-view video cameras for stable gaze-tracking imaging of high-speed moving targets. This paper proposes a high-precision attitude adaptive integral sliding mode control method with a feedforward compensation disturbance observer to enhance the capability of a microsatellite attitude control system for gaze tracking of high-speed moving targets. Specifically, first, we present the attitude control system model for microsatellites and the calculation method for the desired attitude of target tracking based on image feedback. Then, an adaptive integral sliding mode attitude control algorithm with a feedforward compensation disturbance observer, which meets the requirements of high-precision tracking control, is designed. The developed algorithm utilizes the disturbance observer to observe the friction torque of the flywheel and compensates for it through feedforward control. It also employs the adaptive integral sliding mode control algorithm to reduce the impact of uncertain disturbances, decrease the steady-state error of the system, and enhance the attitude control precision. Simulation experiments demonstrated that the designed disturbance observer can successfully observe the frictional disturbance torque of the flywheel. The attitude Euler angle control precision for high-speed moving target tracking reached 0.009°, and the angular velocity control precision reached 0.005°/s, validating the effectiveness of the proposed approach.

In this perspective article, we ponder topographical enhancements of artificial neural networks. In our recent paper in JMLR, we proved a quasi-equivalence between the network width and depth and also discussed the power of intra-links, which can be viewed as network height. In 1982, Hopfield published a network to model human associative memory, which contains many loops for dynamic evolution toward fixed points. Based on noising-denoising loops, diffusion models are recently developed to enable Bayesian modeling and inference with big data. Furthermore, we envision development of multi-AI-agent systems through “netware” engineering as a quantum leap of software engineering for emergent behaviors and autonomous AI at individual and population levels. We believe that the novel use of links and loops in space and time via multi-scale coupling would catalyze the next-generation neural networks.

As of not long ago, understanding the administrative conduct of cells has been sought after through autonomous investigation of the transcriptome or the proteome. In view of the focal creed, it was commonly accepted that there exist an immediate correspondence between mRNA records and produced protein articulations. In any case, late examinations have demonstrated that the relationship among's mRNA and Protein articulations can be low because of different factors, for example, unique half lives and post record apparatus. In this manner, a joint investigation of the transcriptomic and proteomic information can give valuable experiences that may not be translated from singular examination of mRNA or protein articulations. This article audits the current significant methodologies for joint investigation of transcriptomic and proteomic information. We order the various methodologies into eight primary classes dependent on the underlying calculation and last investigation objective. We further present analogies with different spaces and talk about the current exploration issues around there.

Evodiamine is a bioactive alkaloid that is specified as a biomarker for the quality assessment of Evodia rutaecarpa and for traditional Chinese medicines containing this plant. We previously reported that quantitative structure-activity modeling indicated that evodiamine may cause cardiotoxicity. However, previous investigations have indicated that evodiamine has beneficial effects in patients with cardiovascular diseases and there are no previous in vitro or in vivo reports of evodiamine-induced cardiotoxicity. The present study investigated the effects of evodiamine on primary cultured neonatal rat cardiomyocytes in vitro, and on zebrafish in vivo. Cell viability was reduced in vitro, where evodiamine had a 24-h 50% inhibitory concentration of 28.44 µg/mL. Cells exposed to evodiamine also showed increased lactate dehydrogenase release and maleic dialdehyde levels, and reduced superoxide dismutase activity. In vivo, evodiamine had a 10% lethal concentration of 354 ng/mL and induced cardiac malfunction, as evidenced by changes in heart rate and circulation, and pericardial malformations. This study indicated that evodiamine could cause cardiovascular side effects involving oxidative stress. These findings suggest that cardiac function should be monitored in patients receiving preparations containing evodiamine.

Vibration signal analysis is regarded as a fundamental approach in diagnosing faults in rolling bearings, and recent advancements have shown notable progress in this domain. However, the presence of substantial background noise often results in the masking of these fault signals, posing a significant challenge for researchers. In response, an Adaptive Denoising Autoencoder (ADAE) approach is proposed in this paper. The data representations are learned by the encoder through convolutional layers, while the data reconstruction is performed by the decoder using deconvolutional layers. Both the encoder and decoder incorporate adaptive shrinkage units to simulate denoising functions, effectively removing interfering information while preserving sensitive fault features. Additionally, dropout regularization is applied to sparsify the network and prevent overfitting, thereby enhancing the overall expressive power of the model. To further enhance ADAE's noise resistance, shortcut connections are added. Evaluation using publicly available datasets under scenarios with known and unknown noise demonstrates that ADAE effectively enhances the signal-to-noise ratio in strongly noisy backgrounds, facilitating accurate diagnosis of faults in rolling bearings.

Numerous researchers acknowledge that occupational pension protects employees. However, the total occupational pension is shared by employees and employers in China, which is a cost. This study aimed to explore the occupational pension on corporate social responsibility (CSR) and organizational resilience. We drew upon insights from cost-stickiness and resource-based theories to develop a model that illuminates how occupational pension affected firms’ stance toward CSR in the context of the COVID-19 pandemic and how this, in turn, has result organizational resilience. This study categorized CSR into strategic and responsive activities based on cost stickiness. We selected a total of 34,145 observations of Chinese listed companies over the period 2010-2023 as a sample to investigate whether occupational pension changes CSR strategies. The results showed that the cost pressure to contribute to occupational pension drove firms to reduce their responsive CSR and boost their strategic CSR. Moreover, strategic CSR improved organizational resilience, but responsive CSR did not. This relationship between occupational pension and CSR was significantly and negatively moderated by the minimum wage and population aging. Whereas, the relationship between CSR and organizational resilience was significantly and positively moderated by digital transformation and marketing capabilities. This study has implications for decision-making regarding high-quality firm development.

Focused microwave breast hyperthermia (FMBH) employs a phased antenna array to perform beamforming that can focus microwave energy at targeted breast tumors. Selective heating of the tumor endows the hyperthermia treatment with high accuracy and low side effects. The effect of FMBH is highly dependent on the applied phased antenna array. This work investigates the effect of polarizations of antenna elements on the microwave focusing results by simulations. We explore two kinds of antenna arrays with the same number of elements using different digital realistic human breast phantoms. The first array has all the elements’ polarization in the vertical plane of the breast while the second array has half elements’ polarization in the vertical plane and the other half in the transverse plane, i.e., cross polarization. In total 96 sets of different simulations are performed, and the results show that the second array leads to a better focusing effect in dense breasts than the first array. This work is very meaningful for the potential improvement of the antenna array for FMBH, which is of great significance for the future clinical applications of FMBH. The antenna array with cross polarization can also be applied in micro-wave imaging and sensing for biomedical applications.

The intricate relationship between physical and social environments within organizations plays a pivotal role in shaping sustainable innovation endeavors. This paper presents a comprehensive analysis of two key dynamics that have garnered substantial scholarly attention for promoting sustainable innovation: the physical environment and the organizational climate. To elucidate the intricate interplay between these dynamics, we propose a novel three-dimensional framework that guides the modeling of the intricate processes through which the physical environment and innovation climate synergistically influence innovation outcomes. Building on this framework, we delve into an in-depth literature review concerning physical environments that exert a significant impact on innovation. Through this review, we identify and elaborate on four pivotal elements of the physical environment: communality, personalization, comfort, and healthiness. Leveraging insights gleaned from this review, we outline two promising avenues for future research in the realm of the physical environment's interaction with the innovation climate. Furthermore, we underscore the critical importance of adopting an interdisciplinary approach that seamlessly integrates insights from both the physical and social domains to comprehensively understand the sustainable innovation landscape.

In this study, cement is used as the component that provides the stabilizing effect in order to evaluate the hardness and stability of loess soil. To assess the strength characteristics of loess soil reinforced with cement, samples were created with four different cement contents and three different curing times. The materials were put through a series of tests to determine their flexural strength, direct shear strength, indirect tensile strength, and unconfined compressive strength. An appropriate cement dosage was found, in addition to a durability index that could be used to quantify the effect of water absorption investigations on cement-stabilized loess. Both of these discoveries were made simultaneously. Analyses of investigations such as scanning electron microscopy (SEM) and energy dispersive X-ray fluorescence spectrometry (XRF) examinations were carried out so that the fundamental mechanics of the materials could be comprehended. According to the findings, the cohesion of cement-stabilized loess is significantly more sensitive to structure than the friction angle of the material, and the cohesion is responsible for the increase in shear strength after remolding. To get the desired level of strength, it is necessary to adjust the cement's proportions. In addition, as the curing period progresses, we see an increase in the cement-stabilized loess's resistance and stiffness. This is because of the interactions that take place between the structure and the mineral composition. It is believed that this event was caused by the cementation that occurs naturally. As a consequence of this reaction, the production of new cementitious materials takes place. The cation exchange that causes the hydration and pozzolanic reaction that leads to the creation of aggregates and interparticle flocculation is responsible for their production. These findings suggest that cement may be utilized as a simple and effective method of loess stabilization, which will ultimately result in improved performance of the loess.

The robust control of high precision electromechanical systems, such as micropositioners, is challenging in terms of the inherent high nonlinearity, the sensitivity to external interference, and the complexity of accurate identification of the model parameters. To cope with these problems, this work investigates a disturbance observer-based deep reinforcement learning control strategy to realize high robustness and precise tracking performance. Reinforcement learning has shown great potential as optimal control scheme, however, its application in micropositioning systems is still rare. Therefore, embedded with the integral differential compensator (ID), deep deterministic policy gradient (DDPG) is utilized in this work with the ability to not only decrease the state error but also improves the transient response speed. In addition, an adaptive sliding mode disturbance observer (ASMDO) is proposed to further eliminate the collective effect caused by the lumped disturbances. The sterling performance is revealed with intensive tracking simulation experiments and demonstrates the improvement in the accuracy and response time of the controller.

The root system plays an irreplaceable role in plant growth. Its improvement can increase crop productivity. However, such system is still mysterious for us. The underlying mechanism has not been fully uncovered. The investigation on proteins related to the root system is an important means to complete this task. In the previous time, lack of root-related proteins makes it impossible to adopt machine learning methods for designing efficient models for the discovery of novel root-related proteins. Recently, a public database on root-related proteins was set up and machine learning methods can be applied in this field. In this study, we proposed a machine learning based model, named Graph-Root, for identification of root-related proteins. The features derived from protein sequences and one network were extracted, where the former features were processed by graph convolutional neural network and multi-head attention, and the later features abstracted the linkage between proteins. These features were fed into the fully connected layer to make prediction. The 5-fold cross-validation and independent tests suggested its good performance. It also outperformed the only one previous model, SVM-Root. Furthermore, the importance of each feature type and component in the proposed model was investigated.

The mangrove plant Acanthus ilicifolius and its relative, A. mollis, have been previously proved to possess diverse pharmacological effects. Therefore, evaluating the differentially expressed proteins of these species under tidal flooding stress is essential to fully exploit and benefit from their medicinal values. The roots of A. ilicifolius and A. mollis were exposed to 6 h of flooding stress per day for 10 days. The dry weight, hydrogen peroxide (H2O2) content, anatomical characteristics, carbon and energy levels, and two-dimensional electrophoresis coupled with MALDI-TOF/TOF MS technology were used to reveal the divergent flooding resistant strategies. A. ilicifolius performed better under tidal flooding stress, which was reflected in the integrity of the morphological structure, more efficient use of carbon and energy, and a higher percentage of up-regulated proteins associated with carbon and energy metabolism. A. mollis could not survive in flooding conditions for a long time, as revealed by incomplete cell structures of the roots, less efficient use of carbon and energy, and a higher percentage of down-regulated proteins associated with carbon and energy metabolism. Energy provision and flux balance played a role in the flooding tolerance of A. ilicifolius and A. mollis.

A large body of research has examined people’s attitudes toward mandatory vaccination to cope with the COVID-19 pandemic. However, studies have yet to explore how Chinese people view the COVID-19 vaccine mandates, let alone placing such views in the country’s highly politicized context. On the other hand, facing the high pressure of loosening its zero-COVID policies amidst the worldwide practices of co-existing with the COVID-19 virus, the country has to improve its vaccination coverage quickly. In this situation, it is more than necessary to systematically investigate the Chinese public’s attitude to mandatory vaccination against the virus and the underlying determinants. The current study utilizes data from a national survey adopting quota sampling to analyze the Chinese public’s medical and non-medical considerations when judging compulsory COVID-19 vaccination. The study reveals that thanks to China’s successful lockdown policies, personal risk, and benefit perceptions did not dominate their views regarding vaccination mandates. Instead, conspiracy beliefs regarding the pandemic outbreaks, conspiratorial thinking, and nationalism more strongly predicted their willingness to accept mandatory vaccination. Given the potentially massive impacts of the COVID-19 infection, if China opens its door and loosens its strict quarantine restrictions, the Chinese public needs to be educated with more medically valuable and relevant information to improve their vaccination protection against COVID-19.

This paper presents ConF, a novel deep learning model designed for accurate and efficient prediction of non-coding RNA families. NcRNAs are essential functional RNA molecules involved in various cellular processes, including replication, transcription, and gene expression. Identifying ncRNA families is crucial for comprehensive RNA research, as ncRNAs within the same family often exhibit similar functionalities. Traditional experimental methods for identifying ncRNA fam-ilies are time-consuming and labor-intensive. Computational approaches relying on annotated secondary structure data face limitations in handling complex structures like pseudoknots and have restricted applicability, resulting in suboptimal prediction performance. To overcome these chal-lenges, ConF integrates mainstream techniques such as residual networks with dilated convolutions and cross multi-head attention mechanisms. By employing a combination of dual-layer convolu-tional networks and BiLSTM, ConF effectively captures intricate features embedded within RNA sequences. This feature extraction process leads to significantly improved prediction accuracy compared to existing methods. Experimental evaluations conducted on a ten-fold publicly available dataset demonstrate the superiority of ConF in terms of accuracy, sensitivity, and other perfor-mance metrics. Overall, ConF represents a promising solution for accurate and efficient ncRNA family prediction, addressing the limitations of traditional experimental and computational methods.

Negative corona discharges occur widely in high voltage transmission lines and charged aircraft, which can cause strong electromagnetic interference. Negative corona discharge is typically performed simultaneously at multiple discharge points. In this study, the current and its EM radiation characteristics of single-needle and multi-needle negative corona discharge in different conditions were tested. The current and electromagnetic radiation characteristics of the two discharge structures were compared. The dipole radiation model was established to analyze the EM radiation characteristics of the negative corona discharge.The results show that, It is only when the voltage reaches a certain threshold that the current and electromagnetic radiation fields of the multi-needle discharge structure will be superimposed and their amplitudes will increase significantly. The frequency of electromagnetic radiation signal does not change with the number of needles, cathode geometry and applied voltage, but only depends on ambient pressure. It provides a basis for detecting corona discharge sources under different conditions.

China's cotton production has shown a concentration to the advantageous regions in recent years. Based on the relevant data of cotton production in China, the study measures the cotton production agglomeration levels of 16 major cotton-producing provinces from 1978 to 2020, summarizes the spatiotemporal evolution characteristics of cotton production agglomeration, and analyzes the factors influencing cotton production agglomeration using spatial econometric models. The results indicate that: Firstly, since the opening-up and reform, China's cotton production agglomeration levels have shown an overall upward trend, exhibiting periodic dynamic changes over time, and the spatial pattern reveals a dynamic regional gradient. Secondly, there is spatial correlation among the production scales of cotton in different provinces, with a trend resembling a "U" shape, and the agglomeration form shows a low-level convergence. Thirdly, technological level, policies, substitute industrial products and foreign trade are identified as important factors. The cotton production in each province is spatially correlated through these factors, and there is also a presence of spillover effects. In conclusion, the government should prioritize considerations of various influencing factors to formulate tailored support policies, promote large-scale production to enhance technological levels, and focus on policies aimed at improving the quality of cotton.

Types of DNA recombination include homologous recombination and nonhomologous recombination. Homologous DNA recombination is a general term that includes exchange of information between chromatids: (reciprocal) crossing-over, gene conversion, and post-meiotic segregation. Gene conversion is now thought to be a type of non-Mendelian segregation of heterozygous markers near the recombination initiation site. Thus, it includes both gene conversion and post-meiotic segregation previously described. DNA non-HR including transpositional recombination and site-specific recombination. Our understanding of the molecular mechanism by which DNA recombination occurs has significantly increased in the past decades. Currently The synthesis-dependent strand annealing model is now thought to give rise to most or all noncrossovers, with the double-strand-break repair model forming mainly crossovers. The Shapiro model proposed by Dr. J. Shapiro explains the molecular mechanism of transpositional recombination. Site-specific recombination results from another distinct model. We previously proposed a novel theory which can provide a more reasonable and simpler explanation accounting for DNA HR including the 3 classes of recombinogenic events described above. In the new supplementedly molecular model, DNA meiotic recombination can be initiated by a copy choice mechanism, that is, copying part of 1 single-stranded DNA template, followed by DNA polymerase switching to another single-stranded DNA template, and then resuming the following DNA synthesis along the new template. The current review suggests that transpositional recombination and site-specific recombination should be initiated by copy choice during DNA synthesis rather than break/join mechanism. The work indicates that review of DNA nonhomologous recombination are very necessary. The novel theory would challenge earlier models accounting for transpositional recombination and site-specific recombination and would be critical to the understanding of the mechanisms. We hope copy choice initiating DNA nonhomologous recombination will be one of the concepts that are explored. Proper and specific experiments are required to reconstruct the detailed mechanism described here.

The role of fractional calculus in circuit systems has received increased attention in recent years. In order to evaluate the effectiveness of time-domain calculation methods in the analysis of fractional-order piecewise smooth circuit systems, an experimental prototype is developed and the effects of three typical calculation methods in different test scenarios are compared and studied in this paper. It is proved that Oustaloup’s rational approximation method usually overestimates the peak-to-peak current and brings in pulse-voltage phenomenon in piecewise smooth test scenarios, while the results of two iterative recurrence-form numerical methods are in good agreement with the experimental results. The study results are dedicated to provide a reference for efficiently deploying calculation methods in fractional-order piecewise smooth circuit systems. Some quantitative analysis results are concluded in this paper.

This study aims to put forth a new method to study the socio-spatial boundaries by using georeferenced community-authored reviews for restaurants. In this study, we show that food choice, drink choice, and restaurant ambience can be good indicators of socio-economic status of the ambient population in different neighborhoods. To this end, we use Yelp user reviews to distinguish different neighborhoods in terms of their food purchases and identify resultant boundaries in 10 North American metropolitan areas. This data-set includes restaurant reviews as well as a limited number of user check-ins and rating in those cities. We use Natural Language Processing (NLP) techniques to select a set of potential features pertaining to food, drink and ambience from Yelp user comments for each geolocated restaurant. We then select those features which determine one’s choice of restaurant and the rating that he/she provides for that restaurant. After identifying these features, we identify neighborhoods where similar taste is practiced. We show that neighborhoods identified through our method show statistically significant differences based on demographic factors such as income, racial composition, and education. We suggest that this method helps urban planners to understand the social dynamics of contemporary cities in absence of information on service-oriented cultural characteristics of urban communities.

In this paper, the fixed-time stabilization problem for a class of uncertain chained system is addressed by using a novel nonsingular recursive terminal sliding mode control approach. A fixed-time controller and an adaptive law are designed to guarantee the uncertain chained form system both Lyapunov stable and fixed-time convergent within the settling time. The advantage of the controller based on the sliding mode is that the settling time does not depend on the system initial state. Furthermore, we use RBF neural network to estimate the uncertainty of the system. Finally, the simulation results demonstrate the performance of the control laws.

The paper focuses on the admissibility problem of descriptor fractional-order systems (DFOSs). The alternate admissibility criteria are addressed for DFOSs with order in (0,2) which involve a non-strict linear matrix inequality (LMI) method and a strict LMI method, respectively. The forms of non-strict and strict LMIs are brand-new and distinguished with the existing literature, which fill the gaps of studies for admissibility. These approaches are available to the order in (0,2) without separating the order ranges into (0,1) and [1,2). In addition, a method involved least real decision variables in terms of strict LMIs is derived which is more convenient to process the practical solution. Three numerical examples are given to illustrate the validity of proposed results.

Polyacetylene phytochemicals are emerging as potentially responsible for the chemoprotective effects of consuming apiaceous vegetables. There is some evidence suggesting that polyacetylenes impact carcinogenesis by influencing a wide variety of signalling pathways, which are important in regulating inflammation, apoptosis, cell cycle regulation, etc. Studies have shown a correlation between human dietary intake of polyacetylene-rich vegetables with reduced risk of inflammation and cancer. Polyacetylene supplementation can influence cell growth, gene expression, and immunological responses, and reduce tumour number in rat and mouse models. Cancer chemoprevention by dietary polyacetylenes involves several mechanisms, including effects on inflammatory cytokines, the NF-κB pathway, antioxidant response elements, UPR pathway, growth factor signalling, cell cycle progression, and apoptosis. This review summarises the published research on falcarinol-type polyacetylene compounds and their mechanisms of action regarding cancer chemoprevention and treatment, and also identifies some gaps in our current understanding of the health benefits of these polyacetylenes.

With the development of society and the economy, the unified planning of architectural style has become a difficult problem in the competition between urban expansion and the protection of tra-ditional buildings in villages and towns. At the same time, it also allows people to re-examine the appearance and quality of life of traditional village buildings. In this paper, the Conditional Gen-erative Adversarial Network (CGAN) is used to construct a method of building facade generation in villages and towns, so as to gradually realize the governance of the style of villages and towns. At the same time, it has also reduced the restoration of the facades of villages and towns and the graphic design of rural tourism products, showing its application value and potential in the field of planning and design. In the research, taking villages and towns in the Wuyishan area of China as an example, the method is used to carry out model training, image generation, and comparison of the derivation results of different assumed building contours and product contours. The research shows that: (1) CGAN can be used to derive and design the facades of conventional civil buildings in villages and towns. (2) In terms of product graphic design, especially the common tourist cultural products fans and water cups, show significant potential. (3) The construction of this method is not only applicable to villages and towns under the World Heritage City, but can be further promoted and used in the future for cities and villages that have a demand for architectural style consistency.

To address the insufficient mechanical properties of calcined phosphogypsum, this research aims to investigate the utilization of basalt fiber and calcium carbonate whiskers as reinforcing agents. The study examines their impact on the flexural and compressive strength, toughness, water resistance, and tensile strength of calcined phosphogypsum. In the individual tests, basalt fibers with different lengths (3 mm, 6 mm, 9 mm, and 18 mm) were added at dosages of 0%, 0.5%, 1.0%, and 1.5% respectively. The findings demonstrate that basalt fiber effectively enhances the flexural and compressive strength, toughness, and tensile strength of calcined phosphogypsum, albeit potentially compromising water resistance. Among the various fiber lengths, the 6 mm fibers exhibit the most advantageous influence on the performance of calcined phosphogypsum. A subsequent test was conducted to investigate the impact of cross-scale fibers on the properties of calcined phosphogypsum by mixing 6 mm basalt fibers and calcium carbonate whiskers. The results illustrate that calcium carbonate whisker refines the pores, thereby improving the flexural strength and toughness of calcined phosphogypsum. Furthermore, it compensates for the water resistance limitations associated with the sole utilization of basalt fiber while further augmenting the tensile strength and strain capacity. However, it should be noted that increasing the dosage of both calcium carbonate whiskers and basalt fibers concurrently leads to increased porosity of phosphogypsum and reduced compressive strength.

Copper-catalyzed and organocopper-involved reactions are of great significance in organic synthesis. To have a deep understanding of the reaction mechanisms, the structural characterizations of organocopper intermediates become indispensable. Meanwhile, the structure-function relationship of organocopper compounds would advance rational design and development of new Cu-based reactions and organocopper reagents. Compared to the mono-carbonic ligand, the C,N- and C,C-bidentate ligands better stabilize the unstable organocopper compounds. The bidentate ligands can chelate to the same copper atom via ?2-mode, forming a mono-cupra-cyclic compounds with at least one acute C-Cu-C angle. When the bidentate ligands bind to two copper atoms via ?1-mode at each coordinating site, the bimetallic macrocyclic compounds will form nearly linear C-Cu-C angles. The anionic coordinating sites of the bidentate ligand can also bridge two metals via ?2-mode, forming organocopper aggregates with Cu-Cu interactions and organocuprates with contact ion pair structures. The reaction chemistry of some selected organocopper compounds is highlighted, showing their unique structure-reactivity relationships.

To address the issue of reduced orbit estimation accuracy resulting from discrepancies between in-orbit measured geomagnetic field values and IGRF model values in autonomous orbit estimation of microsatellites based on geomagnetic field measurements, this study introduces an adaptive cubature H-infinity filtering algorithm. Firstly, it presents the low-altitude orbital dynamics model and geomagnetic field measurement model for microsatellites. Subsequently, within the adaptive cubature H-infinity filtering algorithm, a spherical simplex rule and a second-order Gaussian-Legendre quadrature criterion are employed to compute the spherical surface integral and radial integral. Additionally, a spherical simplex-radial quadrature rule is proposed to enhance the approximation accuracy of nonlinear Gaussian weighted integrals. Furthermore, by integrating extended H-infinity filtering based on game theory with the cubature quadrature rule, an inverse proportional relationship between constraint level and filtering innovation is established. This allows for adaptive adjustment of the constraint level to enhance robustness against model errors. Finally, through semi-physical simulation experiments, it is demonstrated that compared with traditional algorithms, the proposed algorithm improves autonomous orbit estimation position accuracy of microsatellites by 7.49%, while also enhancing velocity accuracy by 3.1%, thus validating its effectiveness.

In GNSS/IMU integrated navigation systems, factors such as satellite occlusion and non-line-of-sight conditions can lead to degradation of satellite positioning results, Subsequently affecting the overall accuracy of the integrated navigation system. To address this issue and ef-fectively utilize historical pseudorange information from satellites, this paper proposes a graph optimization-based GNSS/IMU model with virtual constraints. These virtual constraints are con-structed using satellite ‘s position from previous time step, the rate of change of pseudoranges, and ephemeris data. This virtual constraint can serve as an alternative solution for individual satellites in case of signal anomalies, ensuring the integrity and continuity of the graph optimi-zation model. Additionally, this paper conducts an analysis of the graph optimization model constructed using these virtual constraints, comparing it with traditional integrated navigation graph optimization model, and analyzes and reconstructs the marginalization process based on these virtual constraints. The experimental results, compared with tightly coupled Kalman fil-tering and the original graph optimization method on a set of real-world data, demonstrate that the introduction of virtual pseudoranges maintains high positioning accuracy. The RMSE error between it and the original graph optimization remains within 5%, affirming the high feasibility of this approach.

Zearalenone is one of the most prevalent estrogenic mycotoxins produced mainly by Fusarium family fungi, and harmed the heath of animals. Zearalenone hydrolase is an important enzyme capable of degrading zearalenone into a non-toxic compound. Although previous research has investigated the catalytic mechanism of zearalenone hydrolase, information on its dynamic interaction with zearalenone remains unknown. This study aimed to develop a pipeline for identifying the allosteric pathway of zearalenone hydrolase. Using an identity analysis, we identified hub genes whose sequences can generalize a set of sequences in a protein family. We then utilized a neural relational inference (NRI) model to identify the allosteric pathway of the protein throughout the entire molecular dynamics simulation. The production run lasted 1 microsecond, and we analyzed residues 139-222 for the allosteric pathway using the NRI model. We found that the cap domain of the protein opened up during catalysis, resembling a hemostatic tape. We used umbrella sampling to simulate the dynamic docking phase of the ligand-protein complex and found that the protein took on a square sandwich shape. Our energy analysis using both MMPBSA and PMF analysis showed discrepancies, with scores of -8.45 kcal/mol and -1.95 kcal/mol, respectively. MMPBSA, however, obtained a similar score to that of a previous report.

Although mask-wearing is now widespread, knowledge of how to quantify or improve its performance remains surprisingly limited and largely based on empirical evidence. The objective of this study was to visualize the expiratory airflows from facemasks and evaluate aerosol transmission between two persons. Different visualization methods were explored, including the Schlieren optical system, laser/LED-particle imaging system, thermal camera, and vapor-SarGel system. The leakage flows and escaped aerosols were quantified using a hotwire anemometer and a particle counter, respectively. The results show that mask-wearing reduces the exhaled flow velocity from 2~4 m/s (with no facemask) to around 0.1 m/s, thus decreasing droplet transmission speeds. Cloth, surgical, and KN95 masks showed varying leakage flows at the nose top, sides, and chin. The leakage rate also differed between inhalation and exhalation. The neck gaiter has low filtration efficiency and high leakage fractions, providing low protection efficiency. There was considerable deposition in the mouth-nose area, as well as the neck, chin, and jaw, which heightened the risk of self-inoculation through spontaneous face-touching. A face shield plus surgical mask greatly reduced droplets on the head, neck, and face, indicating that double face coverings can be highly effective when a single mask is insufficient. The vapor-SarGel system provided a practical approach to study interpersonal transmission under varying close contact scenarios or with different face coverings.

Disparities between fold amplitude (A) and intrusion thickness (Hsill) are critical in identifying elastic or inelastic deformation in a forced fold. However, accurate measurement of these two parameters is challenging because of the limit in separability and detectability for the seismic data. In the TZ-47 exploring area from the Tarim Basin, Northwest China, we combined wireline data and 3-D seismic data, to accurately constrain the fold amplitude and total thickness of sills that inducing the roof uplift. The measurement results show that the forced fold amplitude is 155 m and the total sill thickness is 148.4 m. When using a magma density of 2.7 g/cm3, and solid rock density of 3 g/cm3, the molten magma thickness at the time of intrusion would be 153.8 m, which is almost no difference from the forced fold amplitude. Therefore, the TZ-47 fold is a pure elastic forced fold induced by emplacement of multiple sills. Measurement solely based on seismic data may not be able to detect some thin interlayers and may result in large errors.

Wear-resistant steel/carbon steel composite plate not only has the double performance advantage of high strength and wear-resistance, but also can reduce energy consumption and production cost. Based on 50% reduction rate, the wear resistance of BTW1/Q345 composite was studied at different annealing temperatures, and the dry friction and wear tests of BTW1/Q345 composite at different annealing temperatures were carried out by using RETC MFT-5000. The macro-micro morphology and wear mechanism of wear marks at different annealing temperatures were analyzed by using white light interference three-dimensional surface profiler, Scanning electron microscope scanning electron microscope (SEM) and backscatter electron diffraction (EBSD) . The results show that with the increase of annealing temperature, the grain size near the scratch of BTW1 in the wear-resistant layer of the composite plate is refined, and the wear-resistant property is higher than that of the original sample.When the annealing temperature is 860℃,the wear resistance is the best.

As the number of end-of-life vehicles continues to grow, the field of separation technology for broken copper and aluminium parts of end-of-life vehicles has emerged as a significant area of research. As a key technology for the separation of non-magnetic non-ferrous metals, such as copper and aluminium, eddy current separation can achieve efficient separation of non-magnetic non-ferrous metals according to their differing conductivity and density. Nevertheless, further research is required in the separation of large-scale broken copper and aluminium parts of end-of-life vehicles. This paper presents a novel magnetic roller model comprising circumferential and axial periodic arrangements of permanent magnets. A single permanent magnet was constructed as an equivalent current model, and the magnetic scalar potential equations were solved using simulation tools. This allowed the distribution of the magnetic field outside the magnetic roller to be studied. The results demonstrate that the novel permanent magnet array magnetic roller can enhance the magnetic field intensity and action distance of the external magnetic field, which is more conducive to the separation of large-scale broken copper and aluminium parts of scrap cars. The findings of this research provide a theoretical foundation for the separation of scrap car broken copper and aluminium parts.

Rapid urbanization has dramatically spurred the economic development over the past three decades, especially in China, but has nevertheless had negative impacts on natural resources since it is an irreversible process. Thus, it is essential to timely monitor and quantitatively analysis the changes in land use over time and to identify the landscape pattern variation related to growth mode in different period. This study aims at inspecting spatiotemporal characteristics of landscape pattern respond to land use changes in Xuzhou city during the period from 1985 to 2015. In this connection, we proposed a new spectral index, named the Normalized Difference Enhanced Urban Index (NDEUI), which combines data from NTL (Nighttime light) from the Defense Meteorological Satellite Program/Operational Linescan System (DMSP/OLS) with annual maximum Enhanced Vegetation Index (EVI) to reduce the detection confusion between urban areas and barren land, as well as follows. NDEUI-assisted Random Forests algorithm was implemented to obtain the land use/land cover (LULC) maps of Xuzhou in 1985, 1995, 2005 and 2015, respectively. Here, four different periods viz. 1985–1995, 1995–2005, 2005–2015 and 1985–2015 are chosen for the change analysis of land use and landscape pattern. The results indicated that the urban area has increased by about 30.65%, 10.54%, 68.77%, and 143.75% during the four periods mentioned above at the main expense of agricultural land, respectively. The spatial trend maps revealed that continuous transition from other land use types into urban land has appeared a dual-core development mode throughout the urbanization process, located at the new city region and the Jiawang district, mainly affected by the construction of new city region, freeway and the high railway station. Furthermore, we quantified the patch complexity, aggregation, connectivity and diversity of landscape employing a number of landscape metrics to represent the changes of landscape pattern at both class and landscape level, affected by urbanization during the study period. The results showed that with regard to the four aspects of landscape pattern, there were considerable differences among the four years, mainly owing to the increasing dominance of urbanized land. Spatiotemporal variation of landscape pattern was also conducted on the basis of subgrids in 900 m × 900 m. Combined with the land use changes and spatiotemporal variation of landscape pattern, it can be concluded that different urbanization modes and intensity result in variously the spatiotemporal evolution of landscape patterns. For Xuzhou city, the urban growth mainly appeared a leapfrog mode alone both sides of the roads during the period of 1985 to 1995, and then shifted into edge-expansion mode during the period from 1995 to 2005, whereas the edge-expansion and leapfrog modes coexisted for the period from 2005 to 2015. The high valuable spatiotemporal information generated utilizing RS and GIS in this study may give assistance to urban planners and policymakers to well understand urban dynamics and evaluate their spatiotemporal and environmental impacts at a local level for the sake of sustainable urban planning in the future.

Using numerical simulation method, combined with the pre-branch material characteristics of the measurement results, based on the LS-DYNA software to simulate the branch crushing process, the analysis found that not only the existence of the cutter cutting in the branch destruction process, there is also the cutting of the opposing surface of the bending fracture, with the increase in the speed of the knife rollers, the cutter cutting resistance increases, the cutting resistance reaches 2690 N when the cutter at 2500 r/min, the cutter cutting resistance is the smallest in the cutting simulation at the blade angle of 55°, the blade angle is more suitable for the cutting of the branch. In the cutting simulation under different cutting edge angles, the cutting resistance of the tool is the smallest when the edge angle is 55°, which is 1860 N. This edge angle is more suitable for branch crushing and cutting. Using Fluent software to analyse the airflow characteristics of the crushing device, it was found that with the increase of the knife roller speed, the inlet flow and negative pressure of the crushing chamber are increasing, the speed of 2500 r/min, the inlet flow and negative pressure were 1.92 kg/s and 37.16 Pa, which will be conducive to the feeding of branches, but the speed is too high and it will also lead to the enhancement of the vortex of part of the area in the crushing device, which will affect the feeding of branches and the throwing of the crushed material. affect the feeding of branches and the throwing out of crushed materials, and finally determined the speed range of the crushing knife roller is 1800 ~ 2220 r/min. Based on ANSYS/Model module modal analysis of the crushing knife roller, the knife roller of the first six orders of the intrinsic frequency and vibration pattern, crushing knife roller of the lowest order of the modal intrinsic frequency of 137.42 Hz, much larger than the crushing knife roller operating frequency of 37 Hz, the machine will not resonate during operation.

Even though inhalation dosimetry is determined by three factors (i.e., breathing, aerosols, and the respiratory tract), the first two categories have been more widely studied than the last. Both breathing and aerosols are quantitative variables that can be easily changed, while respiratory airway morphologies are difficult to reconstruct, modify, and quantify. Despite several methods are available for model reconstruction and modification, developing an anatomically accurate airway model and morphing it to various physiological conditions remains labor-intensive and technically challenging. The objective of this study is to explore the feasibility of using an adjoint-CFD model to understand airway shape effects on vapor deposition and control vapor flux into the lung. A mouth-throat model was used, with the shape of the mouth and tongue being automatically varied via adjoint morphing, and the vapor transport being simulated using ANSYS Fluent coupled with a wall absorption model. Two chemicals with varying adsorption rates, Acetaldehyde and Benzene, were considered, which exhibited large differences in dosimetry sensitivity to airway shapes. For both chemicals, large shape deformations were explored to find the maximal possible morphing; both the maximal and intermediate deformations were simulated for morphology parametric studies. Results show that changing the mouth-tongue shape can alter the oral filtration by 3.2% for Acetaldehyde and 0.27% for Benzene under a given inhalation condition. This study demonstrates that the hybrid adjoint-CFD approach can be a practical and efficient method to investigate morphology-associated variability in inhalation dosimetry of vapors and nanomedicines.

Cartilage development is a tightly regulated process that involves multiple molecules and signaling pathways. The loss of expression of a single gene can alter cell behavior and disrupt the development of the cartilage. Col11a1 encodes the alpha one chain of the minor fibrillar collagen type XI that is essential in skeletal development. We used an RNAi mediated knockdown approach to investigate the role of Col11a1 expression during chondrogenesis in ATDC5 cells. Col11a1 expression promotes the transition of mesenchymal cells to the chondrogenic phenotype, and reduction of Col11a1 expression interferes with cellular differentiation. Our results indicate that collagen α1(XI) protein is required for chondrocyte cell shape, matrix production, mineralization and gene expression through a mechanism that involves AKT/GSK3β/β-catenin and TCF/LEF activity in ATDC5 cells.

In this study, the degradable superhydrophobic Mg/P/Z/F/H (magnesi-um/poly(-caprolactone)/zinc oxide/1H,1H,2H,2H-perfluorodecyltriethoxysilane (PFDTES)/ heating process) composite materials were prepared through one-step method for enhancing the corrosion resistance of AZ91D magnesium alloys. Electrochemical measurements showed that Mg/P/Z/F/H materials significantly improved the corrosion resistance of magnesium alloys in 3.5 wt.% NaCl. The self-cleaning, adhesion and stability tests suggested that Mg/P/Z/F/H composite materials had well self-cleaning properties, good adhesion strength and stability in wet atmosphere.

Background: The aim of this study is to explore the independent and joint associations between physical activity (PA) and sleep duration with depressive symptoms. Methods: We included and analyzed 18,052 participants (age ≥ 20 years) from the cross-sectional National Health and Nutrition Examination Survey (NHANES) conducted between 2007 and 2014. Results: After adjustment, both males and females showed a significant correlation between PA, sleep duration, and depressive symptoms. In the joint association analysis, we found: 1. The interaction between PA and sleep duration was statistically significant in males but not significant in females (P=0.380). 2. Compared to individuals with the lowest PA level and not meeting the National Sleep Foundation's (NSF) guidelines, those with the highest PA level and recommended sleep duration had a 79% decrease in depression risk in males (odds ratio [OR] 0.21, 95% confidence interval [CI] 0.14-0.32) and a 74% decrease in females (OR 0.26, 95% CI 0.20-0.35). 3. In male participants adhering to NSF guidelines, each increase in PA quartile is associated with a 19% reduction in the risk of depression (OR 0.81, 95% CI 0.71-0.92). Conversely, among male participants not adhering to NSF guidelines, there is a 23% decrease in depression risk (OR 0.77, 95% CI 0.69-0.86). For female participants, the respective reductions in depression risk are 20% (OR 0.80, 95% CI 0.73-0.89) and 14% (OR 0.86, 95% CI 0.80-0.93). Conclusion: For males, adherence to recommended sleep duration weakens the relationship between physical activity and depression, while the opposite is observed for females.

The valley pseudospin properties of electrons in two–dimensional hexagonal materials result in lots of fascinating physical phenomena, which opens up the new field of valleytronics. The valley-contrasting physics aims at distinguishing the valley degree of freedom based on valley–dependent effects. Here, we theoretically demonstrate that both of the valley–selective high harmonic generation and valley–selective electronic excitation can be achieved by using an orthogonal two–color (OTC) laser field in gapped graphene. It is shown that the asymmetry degrees of harmonic yields in the plateaus, cutoff energies of generated harmonics and electron populations from two different valleys can be precisely controlled by the relative phase of the OTC laser field. Thus the selectivity of the dominant valley for the harmonic radiation and electronic polarization can be switched by adjusting the relative phase of the OTC laser field. Our work offers an all–optical route to produce the valley–resolved high harmonic emissions and manipulate the ultrafast valley polarization on a femtosecond timescale in condensed matter.

In this paper, a semi-empirical model of air waves induced by falling rock is described. The model is composed of a uniform motion phase (velocity close to 0 m·s^-1) and an acceleration movement phase. The uniform motion phase was determined based on experimentally and the acceleration movement phase was derived by theoretical analysis. A series of experiments were performed to verify the semi-empirical model and elucidated the law of the uniform motion phase. The acceleration movement phase accounted for a larger portion with a greater height of the falling rock. Experimental results of different falling heights of the goaf showed close agreement with theoretical analysis values. The semi-empirical model could accurately and conveniently estimate the velocity of air wave induced by falling rock. Thus, the semi-empirical model can provide a reference and basis for estimating the speed of air waves and designing protective measures in mines.

In the construction of shield crossing existing mined tunnel without load, it is imperative to develop corresponding design standards that reflect actual engineering force characteristics to ensure the successful completion of tunnel construction. This research uses The MIDAS-GTS finite element software to facilitate the creation of a numerical model of the shield structure for an air-push-over mine tunnel project in Changsha, China, investigating the stress field’s evolution during shield construction, and calculating the maximum positive and negative bending moments and maximum axial forces for different structures and other force states under various construction conditions. This study's findings informed the design and construction optimisation of the shield tunnelling empty-push method. The outcomes of this numerical simulation led to several key findings: (1) The soil density exerted a significantly greater impact on the internal forces of the initial support structure than both the tunnel depth and soil Poisson's ratio. Additionally, a sudden shift in internal forces occurred within the 300-350 mm range when the lining thickness was altered. (2) Factors such as the tunnel depth, soil density, soil Poisson's ratio μ, and lining thickness have a similarly influenced internal forces of the segment and the initial support. Notably, the backfill layer thickness significantly affected the segment’s maximum axial force causing an abrupt change of approximately 300 mm. (3) Under the shield machine equipment’s weight constraint, it is essential to control the guide rail’s thickness, to prevent it from becoming overly large.

The dust originating from the extinct lake of the Aral Sea poses a considerable threat to the sur-rounding communities and ecosystems. The accurate location of these wind erosion areas is an essential prerequisite for controlling sand and dust activity. However, few relevant indicators re-ported in the current study can accurately describe and measure wind erosion intensity. A novel wind erosion intensity (WEI) of a resolution unit was defined in this paper based on the deformation due to the wind erosion in this resolution unit. We also derived the relationship between WEI and soil InSAR temporal decorrelation (ITD). The ITD is usually caused by the surface change over time, which is very suitable for describing wind erosion. However, within one resolution unit, the ITD signal usually includes soil and vegetation contributions, and few studies are referred to this. Therefore, we proposed an ITD decomposition model (ITDDM) to decompose the ITD signal of a resolution unit. The least-squares method (LSM) based on singular value decomposition (SVD) is used to estimate the ITD of soil (SITD) within a resolution unit. We verified the results qualitatively by the landscape photos, which can reflect the actual conditions of the soil. At last, the WEI of the Aral Sea from June 23, 2020, to July 05, 2020, was mapped. The results confirmed that (1) Based on the ITDDM model, the SITD can be accurately estimated by the LSM method, (2) the Aral Sea is experiencing severe wind erosion, and (3) The middle, northeast, and southeast bare areas of the South Aral Sea are where salt dust storms may occur.

Magnetometric Resistivity(MMR) Method, which can use the power supply method of the traditional apparent resistivity method to measure the magnetic field. At present, the application research abroad is relatively extensive, but the domestic(China) research on the application of the MMR method is very few, and it is not even well-known. This paper is based on the MMR theoretical method under the point source DC condition, combined with the abnormal potential method and the modified Biot-Savart law, and using the three-dimensional numerical calculation method of the finite difference method to calculate the abnormal potential field, electric field, and magnetic field on the matlab2018a platform. Calculate, realize the multi-physics simulation in the electromagnetic field through Matlab platform programming, and verify the correctness of the algorithm by the spherical anomaly model with an analytical solution. Through the visual simulation of the three-dimensional data volume of the multi-physics field in the electromagnetic field, we can better understand the response mechanism of the electromagnetic field under DC conditions and grasp their three-dimensional spatial distribution rules. It is hoped that the research in this article can help the research of MMR Personnel better use this method for exploration.

With the rapid development of network science, Turing pattern on complex networks has attracted extensive attention from researchers. In this paper, we focus on spatial patterns in multiplex ER (Erdös-Rényi) random networks, taking the predator-prey model with Allee effect and hyperbolic mortality as an example. In theory, the threshold condition for generating Turing pattern is given using the Turing instability theory of multiplex networks. Numerically, we design relevant experiments to explore the impact of network topology on Turing pattern. The factors considered include model parameters, diffusion rate, average degree of the network, and differences in the average degree of different layers. The results indicate that the importance of diffusion rate and network average degree for Turing pattern is affirmed on the single-layer network. For multiplex networks, the differentiation of average degrees in different layers controls the generation of Turing pattern, which is not affected by the diffusion rates of the two populations. More interestingly, we observe the switching of Turing pattern and spatiotemporal pattern. We believe that these findings contribute to a better understanding of self-organization on complex networks.

The structure characterization of two new polysaccharides from Agrocybe aegerita (AA-P) and Hygrophorus olivaceoalbus (HO-P) by HPGPC, GC-MS, NMR and FT-IR indicated that AA-P was composed of Galactose, Glucose and Arabinose, in the ratio of 3:2:1. Its skeleton structure was consisted of (1→4)-Arap, (1→4,6)-Glup and (1→6)-Galp with one branched chain. The HO-P was consisted of mannose, galactose and glucose in a ratio of 1:1:2. Its skeleton structure was consisted of (1→6)-Galactose residues, (→1)-glucose residues, (1→4)-glucose residues and (1→4,6)-D-mannose residues. There were two branched chains connected to the main chain. AA-P and HO-P had the best stimulation effect on B cells and RAW264.7 cells, respectively, and could both mainly by impacting and reducing G0/G1 phase which lead to a significant proliferation of B cells, T cells and RAW264.7 cells. In addition, AA-P and HO-P could significantly promote the secretion of TNF-α from T cells, the secretion of IgA, IgD, IgE, IgG and IgM from B cells, and the secretion of TNF-α from RAW264.7 cells, but neither of them could impact the secretion of IL-1β from RAW264.7 cells.

Polymethyl methacrylate (PMMA) polymer is widely used in various fields today. In order to thoroughly reveal the structural impact performance of PMMA materials, this paper is based on the comprehensive Johnson-Cook constitutive model and damage failure model, and accurately confirm the J-C constitutive and damage failure model parameters of PMMA through material test data, The dynamic process of steel bullet impacting PMMA plate structure is analyzed by finite element software ABAQUS. The calculation results show that the numerical simulation results in this paper are in good agreement with the experimental test data. Therefore, the feasibility and accuracy of the impact analysis of PMMA structures based on J-C constitutive and damage failure models in this paper are studied. Finally, based on the J-C constitutive model and damage failure model, the variation of the residual velocity of the bullet with the PMMA plate thickness is analyzed in depth, that is, the results show that the residual velocity of the bullet has a certain linear relationship with the plate thickness.

Sign language recognition is essential in hearing-impaired people’s communication. Sign language recognition is an important concern in computer vision and has been developed with rapid progress in image recognition technology. However, sign language recognition using a general monocular camera has problems with occlusion and recognition accuracy in sign language recognition. In this research, we aim to improve accuracy by using a 2-axis bending sensor as an aid in addition to image recognition. We aim to achieve higher recognition accuracy by acquiring hand keypoint information of sign language actions captured by a monocular RGB camera and adding sensor assist. To improve sign language recognition, we need to propose new AI models. In addition, the amount of dataset is small because it uses the original data set of our laboratory. To learn using sensor data and image data, we used MediaPipe, CNN, and BiLSTM to perform sign language recognition. MediaPipe is a method for estimating the skeleton of the hand and face provided by Google. In addition, CNN is a method that can learn spatial information, and BiLSTM can learn time series data. Combining the CNN and BiLSTM methods yields higher recognition accuracy. We will use these techniques to learn hand skeletal information and sensor data. Additionally, the 2-axis Bending sensor glove data support training AI model. Using these methods, we aim to improve the recognition accuracy of sign language recognition by combining sensor data and hand skeleton data. Our method performed better than using skeletal information, achieving 96.5% accuracy in Top-1.

Land use is an embodiment of human socioeconomic activities and represents a bridge between these activities and natural systems. Through social activities, humans transform land use to promote social and economic development and improve production, living conditions, and eco-logical functions of land. Rural residential land represents a space for rural residents to reside in and exhibits spatial characteristics that evolve over time, which is proof of rural socioeconomic development. This paper observes rural residential land in 21 cities on the Grand Canal and analyses its spatial differentiation. Then, it explores the driving factors of this land using spatial grid analysis and the geographic detector model. Lastly, it proposes three different forms of rural residential land based on the results. The study found that: (1) the change of rural residential land in the northern part of the Grand Canal was more volatile than that in the southern part. The change of rural residential land from 1990 to 2020 conformed to the pattern of cultivated land - rural residential land - urban construction land; (2) Based on the driving factors of rural residen-tial land, the land is divided into one-dimensional cities, two-dimensional cities and three-dimensional cities. Circular, linear, and scattered cities of different sizes were affected by socioeconomic factors, transportation accessibility, and the natural environment, respectively; and (3) Finally, according to the spatial differentiation characteristics and the driving factors of rural residential land, the study proposes the construction of three types of villages through the strate-gies of constructing large-scale villages, relocating and reconstructing new villages, and con-structing high-quality villages, respectively. Enhancing the scientific planning of rural residential land and its efficiency can offer the protection of agricultural land and the integration of urban and rural areas in the new era.

Failure characteristics induced by unloading disturbance and the corresponding mechanical mechanism of the coal seam floor are important theoretical bases for water-bursting prevention from the floor of the coal seam and rock burst alarm in deep mining. However, the existing two-dimensional ground-pressure-control theory based on shallow mining cannot sufficiently guide deep-mining practices. In this study, the redistribution of mining-induced stress field in rocks surrounding the longwall face and mechanical behaviors of strata in deep mining are investigated through a combination of numerical simulation, physical simulation, and field measurement. Results demonstrate that mining-induced stress fields in the floor of the longwall face differ in space and time. Vertical stress unloading from top to bottom of the floor and horizontal stress unloading are relatively low. A concentration zone of high horizontal stress exists at stope boundaries. The critical yield load of rock stratum in the floor is determined through thin plate yield theory. Under the combined effect of concentrated high horizontal and vertical resilience stresses, strata in the floor fracture from seam to seam if the load increases to the minimum critical buckling value. Fractured strata slide along the fracture surface, which leads to floor heave. The stope floor shows evident time-delay progressive failure characteristics. The stress shell in the stope floor in deep mining is found to be a sensitive mechanical parameter that produces three-dimensional ground-pressure behavior in the floor. This ground-pressure behavior in the stope floor is controlled by the existence of the corresponding stress shell and effects induced by its space–time evolution. This study provides theoretical basis for the dynamic control of a hazard-inducing environment in engineering and minimizing or altering disaster-occurrence conditions during the construction engineering of the coal seam floor.

Intergenerational integration has given rise to a novel aging paradigm known as all-age communities, which is garnering international attention. In China, the aging population and the implementation of the three-child policy have resulted in increased demand for retirement and childcare services among residents in older neighborhoods. Consequently, there is a pressing need to retrofit these older neighborhoods to accommodate all-age living arrangements given the high demand they generate. Therefore, this study undertakes research interviews with residents and constructs an exploratory theoretical model rooted in established theory. To assess the significance of our model, we employ Smart PLS 3.0 based on 297 empirical data points. Our findings indicate that anxiety has a significant negative effect on payment behavior; objective perception, willingness to pay, and government assistance exert significant positive effects on payment behavior. By comprehensively analyzing the mechanisms underlying residents’ payment behavior, this study provides valuable insights to the government for promoting the aging process within communities and formulating effective transformation policies.

Today, the digital economy has pursued the required social and economic development, and enterprises can achieve long-term sustainability by relying on the digital platform ecosystem. However, the development of the digital economy and the rapid growth of platform ecosystems have also generated some problems. To study effective digital platform ecosystem governance, this study used the tripartite evolutionary game method and analyzed the changes and effects of platform regulation under different development stages from the perspectives of government, platforms, and enterprises. The results indicate that in the early stages, digital platforms primarily relied on the government’s obligation to regulate. With the digital platform ecosystem’s evolution, the platform organization and settled enterprises’ governance effects gradually appeared, establishing the three common constraints of governance mode. Finally, when the digital platform ecosystem is in its self-renewal period, the government effect is reduced, with the platform itself and settled enterprises taking primary supervisory roles. This study provides reasonable methods for effective platform governance at different stages and enriches the theoretical basis and management practices of platform ecosystems.

Existing one-shot neural architecture search (NAS) methods have to conduct a search over a giant super-net, which leads to the huge computational cost. To reduce such cost, in this paper, we propose a method, called FTSO, to divide the whole architecture search into two sub-steps. Specifically, in the first step, we only search for the topology, and in the second step, we search for the operators. FTSO not only reduces NAS’s search time from days to 0.68 seconds, but also significantly improves the found architecture's accuracy. Our extensive experiments on ImageNet show that within 18 seconds, FTSO can achieve a 76.4% testing accuracy, 1.5% higher than the SOTA, PC-DARTS. In addition, FTSO can reach a 97.77% testing accuracy, 0.27% higher than the SOTA, with nearly 100% (99.8%) search time saved, when searching on CIFAR10.

An analytical method was established by HPLC-DAD-ELSD with C18-NH2 column tandem for the simultaneous determination of hydrophobic components atractylenolide I, II, III, atractylone and hydrophilic compounds glucose, fructose and sucrose in the dried rhizome of Atractylodes macrocephala Koidz (a natural raw material for health foods, Bai-Zhu aka. in Chinese). The method combines different separation capabilities of reversed-phase liquid chromatography and hydrophilic interaction liquid chromatography, can provide a new choice for the simultaneous determination of hydrophilic and hydrophobic compounds in traditional Chinese medicines and health foods. It provided a reference method for the quality control of Bai-Zhu. The results showed that the linear correlation coefficients of the established column tandem chromatographic method were all greater than 0.9990, the relative standard deviation was 0.1%-2.8%, and the average recovery was 96.7%-103.1%. The contents of atractylenolide I, II, III, atractylone, fructose, glucose, and sucrose in 17 batches of Baizhu were 172.3-759.8 μg/g, 201.4-612.8 μg/g, 160.3-534.2 μg/g, 541.4-8723.1 μg/g, 6.9-89.7 mg/g, 0.7-7.9 mg/g, and 1.2-21.0 mg/g, respectively.

The application of artificial intelligence to point-of-care testing (POCT) disease detection has become a hot research field, in which breath detection which detects the patient's exhaled VOCs combined with sensor arrays of Convolutional Neural Network (CNN) algorithms as a new lung cancer detection is attracting more researchers' attention. However, due to low accuracy, high complexity computation and large number of parameters make the CNN algorithms difficult transplant to the embedded system of POCT devices. A lightweight neural network (LTNet) in this work is proposed to deal with this problem, and meanwhile, achieve high-precision classification of acetone and ethanol gases, which are respiratory markers for lung cancer patients. Compared to currently popular lightweight CNN models such as EfficientNet, LTNet has fewer parameters (32K) and its training weight size is only 0.155 MB. LTNet achieved an overall classification accuracy of 99.06% and 99.14% in the own mixed gas dataset and the University of California (UCI) dataset, which are both higher than that of the five existing models’, and it also offers the shortest training (844.38s and 584.67s) and inference time (23s and 14s) in the same validation set. Compared to the existing CNN models, LTNet is more suitable for resource-limited POCT devices.

In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

This paper delves into the concept of information within the context of conscious systems, emphasizing the pivotal role of entropy as a fundamental aspect in comprehending consciousness. Drawing on insights from Integrated Information Theory (IIT) and information theory, the argument posits that consciousness entails dynamic information processing, distinct from the static storage and retrieval model employed by modern computers. The intrinsic dynamics of neural systems are explored, illuminating how they integrate incoming stimuli into a unified state of subjective experience, thereby shaping conscious awareness. By considering entropy as a temporal and qualitative value, its significance in reducing uncertainty and facilitating adaptability in conscious systems is underscored. Through a series of principles, the intricate relationship between entropy, neural dynamics, and consciousness is elucidated. This analysis suggests the necessity of rethinking traditional notions of information when applied to conscious systems, highlighting the dynamic nature of consciousness and its interaction with the environment.

Aiming at the problems that the parameters of YOLOv5s model are too large and the computing resources of development board memory are limited, a new target detection method based on deep learning YOLOv5 algorithm model is proposed. First, the light-weight module Gz-ShffleNetv2 is used to construct cotton top bud feature extraction unit, which reduces the number of parameters and improves the running speed. It can be better applied in image classification, speed up detection and meet the requirements of mobile end of development board. Secondly, in order to solve the problem of decreasing detection accuracy caused by lightweight, BotNet and C3SE attention mechanism are added to focus on specific areas of cotton terminal bud. Combined with YYG loss function XIOU boundary frame regression loss, more feature information and rich feature MAP were obtained to further improve the accuracy of target detection. Through analysis of research and experimental results, the average accuracy map reached 91.3% under the Windos system NVIDIA Geforce RTX 2060 SUPER detection. While maintaining high precision identification, the number of parameters of YOLOv6 and YOLOv7-tiny network model is reduced by 83% and 53%, respectively, and the detection accuracy is increased by 1.2% and 7.7%, respectively. Compared with YOLOv5 reasoning image, the speed of image is increased by 0.035s, and the detection accuracy of MAP_0.5:0.95 is increased by 1%. At the same time, PyQt5 and YOLOv5 target detection algorithms are used to design a cotton top bud identification system, which makes cotton top bud detection more intuitive and convenient for subsequent hardware development and use.

By the study of the pattern book Ying Zao Fa Shi (building regulations of Song Dynasty, 1103 AD), while analyzing the combining and dimensioning rule of timber framework and tile work, a model self-generating program has been compiled for the first time. The operating framework has been firstly defined, while solving the issues of clustering principle, connecting method, output classification, etc. with the detailed description of algorithm theory. Taking the corner bracket set and nine-ridge roof for example, after the compilation and debug by Grasshopper, according to various input parameters, various models have been generated automatically by the plugin, proving the velocity and the veracity of the algorithm.

There is a confusion in the original design concept for the tensioning of longitudinally connected reinforcement of CRTSII slab ballastless track. In order to clarify the effect of tension value of longitudinal reinforcement on mechanical characteristics of ballastless track, a three dimensional finite element model considering the nonlinear interaction between the track slab and CA mortar of CRTSII slab ballastless track was established. The mechanical characteristics of the track structure under longitudinal tension load and temperature gradient load of the longitudinal joint were calculated. A method of applying pre-stress to post-pouring concrete was proposed according to the concept of pre-stress loss of pretensioning pre-stressed concrete, reasonable tensile force value was proposed after the crack width and the reinforcement stress of the ballastless track in the operation stage were checked and calculated according to the concrete design principle. When the tension force is greater than 300 kN, it’s harmful to the bonding between the slab and mortar layer, which is prone to interlayer damage. In order to adding pre-stress to concrete of wide joints to ensure the longitudinal stability of ballastless track and the reinforcement stress and crack width to meet the design requirements. It is suggested that the tension force value should be 230 kN, and the temperature difference between reinforcement and concrete should be 30 °C before the initial curdle of wide joint concrete.

To realize the utilization of peanut shell, this study investigates the combustion behavior, chemical kinetics, and thermodynamic parameters of peanut shell using TGA under atmospheric air. Results indicate that increasing the heating rate leads to higher ignition, burnout, and peak temperatures, as observed in the TG/DTG curves shifting to the right. Analysis of combustion performance parameters suggest that higher heating rates can enhance combustion performances. Kinetic analysis using two model-free methods, KAS and FWO, shows that the activation energy (Eα) ranges from 93.30 to 109.65 kJ/mol for FWO and 89.72 to 103.88 kJ/mol for KAS. The data fit well with coefficient of determination values (R2) close to 1. Pre-exponential factors using FWO range from 2.19×106 to 8.06×107 s–1, and for KAS range from9.72×105 to 2.25×107 s–1. Thermodynamic analysis indicates a low-energy barrier (≤ ±6 kJ/mol) between activation energy and enthalpy changes, suggesting easy reaction initiation. Furthermore, variations in enthalpy (ΔH), Gibbs free energy (ΔG), and entropy (ΔS) upon conversion (α) suggest that peanut shell combustion is endothermic and non-spontaneous, with the generation of more homogeneous or well-ordered products as combustion progresses. These findings offer a theoretical basis and data support for the further utilization of agricultural biomass.

Psoriasis is a chronic, multisystem, inflammatory disease. The typical clinical cutaneous manifestation of psoriasis is scaly erythema or plaque, limited or widely distributed. However, psoriasis is far beyond the skin involvement and provides many challenges, including associated comorbidities. In this review, we classify psoriasis as cutaneous and systemic psoriasis, according to the clinical diversity and associated comorbid diseases, and recommend classification criteria for psoriasis. The key objective of this novel classification is to raise awareness of the complexity of this multifaceted disease and help to better understand and manage this complex disease comprehensively.

Coronavirus disease 2019 (COVID-19) is caused by infection with the 2019 novel coronavirus 2 (2019-nCoV, now referred to as SARS-CoV-2). COVID-19 has become a global pandemic since its outbreak at the end of Dec 2019. COVID-19 could lead to severe acute respiratory disease, especially to those who have reduced immunity. Binding of the viral Spike protein (S) to its receptor ACE2 (Angiotensin Converting Enzyme 2) on the surface of target cells has been proven to be key for virus entry and infection. Although ACE2 expression in the respiratory system is necessary for pneumonia infection by SARS-CoV-2, the regulation of ACE2 gene expression remains poorly investigated, especially for patients that are in pre-pathological conditions. Here, by analyzing The Gene Expression Omnibus (GEO) database, we investigated the expression regulation of ACE2 in various kinds of primary epithelial cells from the respiratory system after varies of respiratory viruses infection such as influenza A virus (IFV), respiratory syncytial virus (RSV) and human rhinovirus (hRV). Our analyses reveal that infection of multiple kinds of respiratory viruses or influenza vaccines greatly increased ACE2 expression, suggesting that respiratory viruses infection could represent a high risk factor for developing COVID-19. We also found that the regulatory effect of influenza A virus on ACE2 expression is associated with activation of the interferon beta-induced pathway and viral RNA-activated host response. Together, our data provide a theoretical framework for clinical classification for SARS-CoV-2 infection susceptibility and could be used for future prevention and therapy treatment for COVID-19.

Background: The Hengduan Mountains are one of the most species–rich mountainous areas in the world. The origin and evolution of such a remarkable biodiversity are likely to be associated with geological or climatic dynamics, as well as taxon-specific biotic processes (e.g., hybridization, polyploidization, etc.). Here, we investigate the mechanisms fostering the diversification of the endemic Himalopsyche martynovi complex, a poorly known group of aquatic insects. Methods: We used multiple allelic datasets generated from 691 AHE loci to reconstruct species and RaxML phylogenetic trees. We selected the most reliable phylogenetic tree to perform network and gene flow analyses. Results: Phylogenetic reconstructions and network analysis identified three clades, including H. epikur, H. martynovi sensu stricto and H. cf. martynovi. Himalopsyche martynovi sensu stricto and H. cf. martynovi present an intermediate morphology between H. epikur and H. viteceki, the closest known relative to the H. martynovi–complex. The gene flow analysis revealed extensive gene flow among these lineages. Conclusion: Our results suggest that H. viteceki and H. epikur are likely to have contributed to the evolution of H. martynovi sensu stricto and H. cf. martynovi via gene flow, and thus, our study provides insights in the diversification process of a lesser–known ecological group, and hints at the potential role of gene flow in the emergence of biological novelty in the Hengduan Mountains.