Bionic robotic hand can perform many movements similar to human hand. But there is still a significant gap in manipulation between robot and human hand. It is necessary to understand the finger kinematics and motion patterns of human hand to improve the performance of robotic hand. This study aimed to comprehensively investigate normal hand motion patterns by evaluating the kinematics of hand grip and release in healthy individuals. The data corresponding to rapid grip and release were collected from the dominant hand of 22 healthy people by sensory glove. The kinematics of 14 finger joints were analyzed, including the dynamic range of motion (ROM), peak velocity, joint sequence and finger sequence. The results show that the proximal interphalangeal (PIP) joint had a largest dynamic ROM than metacarpophalangeal (MCP) and distal interphalangeal (DIP) joints. Besides, the PIP joint had the highest peak velocity, both in flexion and extension. For joint sequence, the PIP joint moved prior to the DIP or MCP joints during flexion, while extension started in DIP or MCP joints, followed by PIP joint. Regarding the finger sequence, the thumb started to move before four fingers, and stopped moving after the fingers during both grip and release. This study explored the normal motion patterns in hand grip and release, which provided kinematic reference for the design of robotic hand and thus contribute to its development.

Aiming at the removal of radioactive cobalt ions from water by graphene oxide (GO), the adsorption mechanism of Co2+ on graphene oxide was analyzed using the quantum chemical calculation software Gaussian 16 based on the density functional theory. The influence of material structure factors such as carboxyl group, hydroxyl group, epoxy group and graphene sheet as well as external environmental factors such as pH, temperature and interfering ions on the adsorption effect was determined, and the influence of external environment was verified through experiments. Through calculation and experiment, it was found that the existence of oxygen-containing functional groups on graphene oxide can improve the adsorption efficiency of the materialappropriately,and increasing pH under acidic conditions was also helpful to improve the adsorption effect, and the material had certain selectivity for Co2+, the adsorption capacity and selectivity could be further improved when it was modified by increasing hydroxyl group.

As a critical transmitter, the compact 532 nm lasers operating on high repetition and narrow pulse widths have been used widely for airborne or space-borne laser active remote sensing. We developed a free space pumped TEM₀₀ mode sub-nanosecond 532 nm laser that occupied a volume of less than 125 mm × 50 mm × 40 mm (0.25 liters). The fundamental 1064 nm laser consists of a passively Q-switched composite crystal microchip laser and an off-axis, two-pass power amplifier. The pump sources were two single-emitter semiconductor laser diodes (LD) of 808 nm with a maximum continuous wave (CW) power of 10 W each. The average power of fundamental 1064 nm laser was 1.26 W with the laser operating at 16 kHz repetition rates, and 857ps pulse widths. Since the beam distortion would be severe in microchip lasers in terms of the increase in heat load, for obtaining a high beam quality of 532 nm, the beam distortion was compensated by adjusting the distribution of pumping beam in our experiment of fundamental amplification. Furthermore, better than 0.6 W average power, 770 ps, beam quality of M² ＜1.2, and 16 kHz pulse output at 532 nm was obtained by a Type I LiB₃O₅ (LBO) crystal in the critical phase matching (CPM) regime for second harmonic generation (SHG).

We tested selecting data randomly or proportionally in class imbalanced sample. Collecting data into the training and test set according to the initial ratio of QSOs, galaxies and stars were rec-ommended. We experimented using the original imbalanced data or introducing the class balance technologies: SMOTE, SMOTEENN, SMOTETomek, ADASYN, BorderlineSMOTE1, Border-lineSMOTE2, and RandomUndersampling. The SMOTEENN performed the best in the Sample 1. The LightGBM, CatBoost, XGBoost, and RF were compared when adopting the SMOTEENN using the petroMag_u, petroMag_g, petroMag_r, petroMag_i, petroMag_z, J, H, Ks, W1, W2, W3, W4 magnitudes as features. All of the precisions or recalls exceeded 0.94. The RF cost a little more time than the other three algorithms, but resulted in the best evaluating indicators. Utilizing the SMOTEENN +RF technology, the precision, recall and f1-score for QSOs (galaxies, stars) could achieve 0.98 (0.99, 0.98), 0.99 (0.96, 1.00), 0.98 (0.97, 0.99) respectively in Sample 1. Utilizing the SMOTEENN +RF technology, the precision, recall and f1-score for QSOs (galaxies, stars) could achieve 0.94 (0.96, 0.96), 0.98 (0.90, 0.97), 0.96 (0.93, 0.97) using the petroMag_u, petroMag_g, petroMag_r, petroMag_i, petroMag_z, W1, W2, W3, W4 magnitudes as features.

This article is a study on the (k,s)-Riemann-Liouville fractional integral, a generalization of the Riemann-Liouville fractional integral. Firstly, we introduce several properties of the extended integral of continuous functions. Furthermore, we make the estimation of the Box dimension of the graph of continuous functions after the extended integral. It presents that the upper Box dimension of the (k,s)-Riemann-Liouville fractional integral for any continuous functions is no more than the upper Box dimension of the functions on the unit interval I=[0,1], which indicates that the upper Box dimension of the integrand f(x) will not be increased by the σ-order (k,s)-Riemann-Liouville fractional integral ksD−σf(x) where σ>0 on I. Additionally, we prove that the fractal dimension of ksD−σf(x) of one-dimensional continuous functions f(x) is still one.

The majority of existing numerical simulations of the effect of bridge piers on water movement are based on a limited number of bridge piers at a laboratory scale. Furthermore, some 2D numerical simulations for actual bridge projects have deficiencies, including the use of overly large mesh sizes and an inadequate treatment of bridge piers. In this study, we compare three methods of structural mesh encryption, suspension mesh, and nonstructural mesh based on Delft3D, and apply the optimization scheme to a real bridge project. It is demonstrated that optimal results can be achieved by utilising a grid size comparable to the pier diameter (Dp) in the region away from the piers. In the vicinity of the piers, the grid cell size should be no larger than 1/9 Dp. The suspended grid technique (DD Boundary) can yield results consistent with those obtained using a full-area high-resolution grid, provided that the total number of grids can be reduced and the computational time is considerably reduced. In this study, the unstructured mesh (Deflt3D Flexible Mesh) scheme was unable to capture the oscillations of the wake flow behind the bridge piers. However, the application of the optimized scheme in bridge engineering has demonstrated its practical value. The findings of this study on mesh resolution and suspension mesh scheme can be applied to the Delft3D software and are also useful for other numerical simulation work.

Heterosis plays a significant role in enhancing variety, boosting yield, and raising economic value, but the molecular mechanism is still unclear. We analyzed the transcriptomes and 3D genomes of hybrid (F1) and its parents (w30 and 082). Analysis of the expression revealed a total of 485 specially expressed genes (SEGs), 173 differentially expressed genes (DEGs) above parental expression level, more actively expressed genes and up-regulated DEGs in F1. Further study revealed that the DEGs detected in F1 and its parents were mainly involved in response to auxin, plant hormone signal transduction, DNA metabolic process, Purine metabolism, starch and sucrose metabolism, which suggested that these biological processes may play a crucial role in the heterosis of B. rapa. The analysis of 3D genome data revealed that hybrid F1 tend to contain more transcriptionally active A compartments after hybridization. Additionally, F1 had a smaller TAD (topologically associated domain) genome length, but the number was the highest, and the expression change of activated TAD was higher than repressed TAD. More specific TAD boundaries were detected between parents and F1. Subsequently, 140 DEGs with genomic structural variants were selected as potential candidate genes. Among them, we found two DEGs with consistent expression changes in A/B compartments and TADs. Our findings suggest that genomic structural variants, such as TADs and A/B compartments, may affect gene expression and contribute to heterosis in B. rapa. This study provides further insight into the molecular mechanism of heterosis in B. rapa.

Arid- and semi-arid Central Asia is particularly sensitive to climate change. The changes in extreme precipitation in Central Asia stemming from climate warming are the subject of intense debate within the scientific community. This study employed a Morlet wavelet analysis to examine the annual occurrence number of extreme precipitation in Central Asia from May to September during the period of 1951–2005. Their modulating planetary-scale climate modes were identified by using a linear regression analysis. Two major scales of the temporal variability were derived: 2–3.9 yr and 4–6 yr. The dominant variability was 2–3.9-yr scale and was associated with the negative phase of the Polar/Eurasia (POL) pattern. The 4–6-yr scale provided a secondary contribution and was closely linked to the negative phase of the North Atlantic Oscillation (NAO). These planetary climate modes acted as precursors of extreme precipitation over Central Asia. The negative phase of POL directly contributed to a negative height anomaly over Central Asia, which was intimately related to extreme precipitation. In contrast, the negative NAO phase possibly manifested as a Rossby wave source, which was subsequently exported to Central Asia through a negative–positive–negative Rossby wave train.

Background: Micronutrients has roles in strengthening and maintaining immune function, but its supplementation and/or deficiency effects on respiratory tract infections are inconclusive. This review aims to systematically assess the associations between micronutrient supplementation or deficiency, with novel coronavirus incidence and disease severity. Methods: Systematic literature searches conducted in 5 electronic databases identified 751 unique studies, of which 33 studies (5 supplementation studies, 1 supplementation and deficiency study, and 27 deficiency studies) were eventually included in this review. Proportions of incidence and severity outcomes in each group, and adjusted summary statistics with their relevant 95% confidence intervaIs (CI) were extracted. Data from 19 studies were pooled in meta-analysis using the generic inverse variance method. Findings: A total of 360,346 patients across 16 countries, with a mean age between 32 and 87.7 years, were involved across 33 studies. All studies were on COVID-19 infections. In individuals without micronutrient deficiency, there was a significant reduction on odds of COVID-19 incidence (pooled OR: 0.37, 95% CI: 0.18, 0.78), and ICU admissions or severe/critical disease onset (pooled OR: 0.26, 95% CI: 0.08, 0.89). Insignificant protective effects were observed on other outcome measures – mortality, ICU admission, progression to respiratory-related complications, severe/critical disease onset or requiring respiratory support and hospitalization rate. Conclusion: The absence of micronutrient deficiency significantly reduced COVID-19 incidence and clinical deterioration in hospitalized patients. Usage of micronutrients as prophylaxis and complementary supplement in therapeutic management of COVID-19 patients may be a promising and cost-effective approach warranting in-depth investigation.

Based on the data of A-share listed companies in Shanghai and Shenzhen of China from 2011 to 2018 and the digital inclusive finance index of Peking University (2011-2018), this paper empirically tests the impact of digital finance development on corporate social responsibility in various provinces of China and its impact mechanism. The results show that: (1) the development of digital finance helps to promote the fulfillment of corporate social responsibility; (2) the influence mechanism of the development of digital finance to promote the fulfillment of corporate social responsibility lies in that it reduces the cost of debt financing and leads to the improvement of corporate social responsibility.(3) Further research shows that the positive relationship between digital finance and corporate social responsibility is more significant in private enterprises. At the same time, the impact is more significant in areas with poor market environment. The above research shows that the development of digital finance has a significant positive effect, which will improve the level of corporate social responsibility.

In this paper, a distributed algorithm is proposed to solve a consensus convex optimization problem. It is a Jacobi-proximal alternating direction method of multipliers with a damping parameter $\gamma$ in the iteration of multiplier. Compared with existing algorithms, it has the following nice properties: (1) The restriction on proximal matrix is relaxed substantively, thus alleviating the weight of the proximal term. Therefore, the algorithm has a faster convergence speed. (2) The convergence analysis of the algorithm is established for any damping parameter $\gamma\in(0,2]$, which is larger ones in the literature. In addition, some numerical experiments and an application to a logistic regression problem are provided to validate the effectiveness and the characteristics of the proposed algorithm.

It is time-consuming for acquiring complete data by fully phase encoding in two orthogonal directions along with one frequency encoding direction. Undersampling in the 3D k-space is promising in accelerating such 3D MRI process. Though 3D undersampling can be conducted according to predefined probability density, the density based method is not optimal. Because of the large amount of 3D data and computational cost, it is challenging to perform data-driven and learning-based 3D undersampling and subsequent 3D reconstruction. To tackle this challenge, this paper proposes a deep neural network called EEUR-Net, realized by optimizing specific undersampling patterns for the fully-sampled 3D k-space data. Innovatively, our undersampling algorithm employs an end-to-end deep learning approach to optimize phase encoding patterns and uses a 3D U-Net for image reconstruction of undersampled data. Through end-to-end training, we obtain an optimized 3D undersampling pattern, which significantly enhances the quality of the reconstructed image under the same acceleration factor. A series of experiments on a knee MRI dataset demonstrated that, in comparison to standard random uniform, radial, Poisson and equispaced Cartesian undersampling schemes, our end-to-end learned undersampling pattern considerably improves the reconstruction quality of undersampled MRI images.

A full connected world is expected to gain in the 6th generation mobile network (6G). As a typi-cal fully connected scenario, the internet of vehicle (IoV) enables intelligent vehicle operations via artificial intelligence (AI) and edge computing technologies. In the future of vehicular net-works, wide variety of services need powerful computing resources and higher quality of ser-vice (QoS). Existing resources are insufficient to match these requirements. Aim to this problem, An intelligent service offloading framework is provided. Based on the framework, an Algorithm of Improved Gradient Descent (AIGD) is created to accelerate the speed of iteration. So, the con-vergence of convolutional neural network (CNN) based on AIGD is able to be accelerated too. Then, an Algorithm of convolutional long short-term memory (CN_LSTM) Based Traffic Predic-tion (ACLBTP) is designed to gain the predicted number of vehicles belonged to the edge node. At last, an Algorithm of Service Offloading Based on CN_LSTM (ASOBCL) is conducted to of-fload these services to the vehicles belonged to the edge node. In ASOBCL, sorting technique is adopted to speed up the offloading work. Simulation results demonstrate the fact that the pre-diction strategy designed in this paper has high accuracy. The low offloading time and main-taining stable load balance is gained via running ASOBCL. Low offloading time means short response time. And, the QoS is guaranteed. So, these strategies designed in this paper are effec-tive and valuable.

In a global context, the story of the Jesuit compound in Shanghai, since its establishment by French Jesuits in 1847, reflected not only conflicts between rival powers in Europe but also the fight for their interests in the Eastern world. The Pope, who was stuck without legal status in the Vatican after 1861, was also seeking the chance to save the authority of the Church in the face of questions regarding the extent of his temporal power and the status of Rome in the context of Italian unification. As in the Reformation, a break-through in the east seemed to offer a solution for losses in Europe. However, the Jesuits to the East in the late 19th century were not only troops working and fighting on behalf of the Pope; their identities under the French Protectorate added complexity to an already complicated story involving not just the Church, but the course of world history.The female Catholic orders at the east bank of Zi-ka-wei compound became a unique window to approach the complexity.

The development of subterranean non-motorized traffic infrastructure, commonly referred to as the underground pedestrian system (UPS), has become increasingly necessary in densely populated megacities worldwide as a means of advancing the Sustainable Development Goal 11, which aims to promote sustainable cities and communities. To improve the overall spatial performance, it is imperative to decipher the fundamental formation mechanism of sustainable underground pedestrian systems (SUPS) that is simultaneously influenced by spatial morphology and pedestrian behaviors. Thereby, two representative case studies, namely Wujiaochang UPS and Loushanguanlu UPS located in Shanghai, were selected for an in-depth investigation. This study employed correlation and regression analysis to examine the impact of spatial configuration variables and spatial attribute factors on pedestrian flow distributions in distinct SUPSs. The findings indicate that the variables of Betweenness, as measured by both Euclidean and Angular metrics, along with the presence of metro station locations and commercial space connected by UPS, are the three most significant factors influencing pedestrian behaviors in both scenarios. The disclosure has been made that Wujiaochang UPS is seamlessly integrated into a comprehensive three-dimensional pedestrian network both above and below ground. On the other hand, it appears that Loushanguanlu UPS exhibits a greater degree of self-sufficiency as an underground system. This study aims to elucidate the mechanism underlying the development of SUPSs, thus offering effective guidance for the implementation of three-dimensional walking systems in cities that prioritize sustainability.

Epoxy asphalt (EA) concrete is widely used in constructing long-span steel bridge pavements (SBDPs). This study aims to derive a fatigue damage evolution law, conducting an experimental investigation of SBDP. First, a general theoretical form of the fatigue damage evolution law of materials is established based on the thermal motion of atoms. Then, fatigue experiments demonstrate that this evolution law well represents the known damage–life relationships of SBDP. Taking into account the experimental relationships between damage and fatigue life under symmetrical cyclic loadings with different overload amplitudes and temperature variations, a detailed damage evolution law is deduced. Finally, the role of damage accumulation is discussed on the basis of the proposed damage evolution law for the extreme situation of heavy overload and severe environments. The results show that both heavy loading and falling temperatures increase the fatigue damage of SBDP considerably; therefore, SBDP should avoid heavy loading combined with winter temperatures. EA shows a fatigue life two to three times longer than that of modified matrix asphalt (SMA) or guss asphalt (GA). For the same thickness, EA pavement is demonstrated to be more suitable for an anti-fatigue design of large-span SBDP under high traffic flows and low temperatures.

Since Hydrogen Sulfide (H2S) was recognized as a gas transmitter, its detection and quantifica-tion have become a hot research topic among chemists and biologists. In this area. fluorescent probes have shown great advantages: fast and strong responds, low detection limit and easy ma-nipulation. Here we developed a new fluorescent probe that detected H2S selectively among various bioactive and inorganic salts. This probe was based on the core structure of fluorescein and reacted with H2S through azide-reduction. Great linearity was achieved correlating fluores-cence intensity and H2S concentrations in solution. The detection of H2S in cancer cells was also achieved.

Runtime verification (RV) is a lightweight approach to detecting temporal errors of system at runtime. It confines the verification on observed trajectory which avoids state explosion problem.To predict the future violation, some work proposed the predictive RV which uses the information from models or static analysis. But for software whose models and codes cannot be obtained, or systems running under uncertain environment, these predictive methods cannot take effect. Meanwhile, RV in general takes multi-valued logic as the specification languages, for example the " true, false and inconclusive" in three-valued semantics. They cannot give accurate quantitative description of correctness when "inconclusive" is encountered. We in this paper present a RV method which learns probabilistic model of system and environment from history traces and then generates probabilistic runtime monitor to quantitatively predict the satisfaction of temporal property at each runtime state. In this approach, Hidden Markov Model (HMM) is firstly learned and then transformed to Discrete Time Markov Chain (DTMC). To construct incremental monitor, the monitored LTL property is translated into Deterministic Rabin Automaton (DRA). The final probabilistic monitor is obtained by generating the product of DTMC and DRA, and computing the probabilities for each state. With such method, one can give early warning once the probability of correctness is lower than pre-defined threshold, and have the chance to do adjustment in advance. The method has been implemented and experimented on real UAS (Unmanned Aerial Vehicle) simulation platform.

In this work, a novel heterojunction based on ZnSnO3/ZnO nanofibers was prepared using electrospinning method. The crystal, structural and surface compositional properties of sample based on ZnSnO3 and ZnSnO3/ZnO composite nanofibers were investigated by X-ray diffractometer (XRD), Scanning electron microscope (SEM), X-ray photoelectron spectrometer (XPS) and Brunauer-Emmett-Teller (BET). Compared to pure ZnSnO3 nanofibers, the ZnSnO3/ZnO heterostructure nanofibers display high sensitivity and selectivity response with fast response towards ethanol gas at low operational temperature. The sensitivity response of sensor based on ZnSnO3/ZnO composite nanofibers were 19.6 towards 50 ppm ethanol gas at 225°C, which was about 1.5 times superior than that of pure ZnSnO3 nanofibers, which can be owed mainly to the presence of oxygen vacancies and the synergistic effect between ZnSnO3 and ZnO.

Exploiting the linguistic knowledge of the source language for neural machine translation (NMT) has recently achieved impressive performance on many large-scale language pairs. However, since the Turkish→English machine translation task is low-resource and the source-side Turkish is morphologically-rich, there are limited resources of bilingual corpora and linguistic information available to further improve the NMT performance. Focusing on the above issues, we propose a multi-source NMT approach that models the word feature in parallel to external linguistic features by using two separate encoders to explicitly incorporate linguistic knowledge into the NMT model. We extend the word embedding layer of the knowledge-based encoder to accommodate for each word’s linguistic annotations in the context. Moreover, we share all parameters across encoders to enhance the representation ability of the NMT model on the source language. Experimental results show that our proposed approach achieves substantial improvements of up to 2.4 and 1.1 BLEU scores in Turkish→English and English→Turkish machine translation tasks, respectively, which points to a promising way to utilize the source-side linguistic knowledge for the low-resource NMT.

Quasi-bound state in the continuum (QBIC) can effectively enhance the interaction of terahertz (THz) wave with matters due to the tunable high-Q property, which has a strong potential application in detection of low-concentration biological samples in the THz band. In this paper, a novel THz metamaterial sensor with a double-chain separated resonant cavity structure based on QBIC is designed and fabricated. The process of excitation of the QBIC mode is verified and the structural parameters are optimized after considering the ohmic loss by simulations. The simulated refractive index sensitivity of the sensor is up to 544 GHz/RIU, much higher than those of recently reported THz metamaterial sensors. Sensing sensitivity of the proposed metamaterial sensor is confirmed in experiment by detecting low-concentration lithium citrate (LC) and bovine serum albumin (BSA) solutions. The limits of detection (LoDs) are obtained to be 0.0025 mg/mL (12 μM) for LC and 0.03125 mg/mL (0.47 μM) for BSA, respectively, both of which excel over most of reported results in previous studies. These results indicate that the proposed THz metamaterial sensor has excellent sensing performances and can well be applied to the detection of low concentration biological samples.

Previously, pseudomyogenic hemangioendothelioma (PMHE) is regarded as epithelioid sarcoma-like hemangioendothelioma due to significant histologic overlapping and diffuse cytokeratin expression since the first description in 1992. After considerable controversy and long-term debating, it is currently defined as a distinct intermediate malignant, rarely metastasizing neoplasm with vascular/endothelial differentiation in nature. PMHE is characterized by young age (typically < 40 years old) and extremity location (approximately ~80%) with t(7:19) SERPINE1-FOSB fusion as the most common molecular alteration. Here we reported a 59-year-old male presenting with multifocal lesions, including right temporalis muscle, right frontoparietal calvarium, right pterygoid muscles, and right mandibular condyle. Histologic examination of the lesion from right temporal mass revealed a multinodular biphasic lesion composed of sheets and fascicles of elongated spindle cells, and epithelioid small round to ovoid cells infiltrating into the adjacent skeletal muscle admixed with abundant neutrophilic infiltration. No rhabdomyoblast-like cells, prominent nuclear pleomorphism and mitosis were identified. IHC staining showed that the tumor cells were diffusely and strongly positive for FOSB, pan-cytokerain (AE1/AE3), CD31, ERG, and molecular testing further demonstrated a t(9:19) EGFL7::FOSB fusion mRNA. This constellation of morphological, IHC and molecular findings was consistent with the diagnosis of PMHE. This is the first reported case of multiple PMHEs with EGFL7::FOSB fusion in a patient aged more than 50 years old in the head and neck area. Since the vast majority of the differential diagnoses of PMHE are high-grade malignancies with aggressive clinical behavior and PMHE is rarely reported in the head and neck region, awareness of this tumor will avoid misdiagnosis and over-treatments of this entity.

Indirect fracturing from roof rock to coal using a horizontal well is a new and promising technology for coalbed methane surface exploitation in soft and low-permeability coal seams. In order to study the propagation law of hydraulic fracture across the coal-rock interface, a pore pressure cohesive element is used to establish a numerical model for indirect fracturing. Combined with practical engineering in 3# coal seam in Xinjing mine in China, the propagation behavior of hydraulic fracture across the coal-rock interface was researched, and the range of horizontal well position for indirect fracturing was determined. The results show that: (1) the pore pressure cohesive element can be used to simulate accurately the interaction between hydraulic fracture and natural fracture, and the propagation of hydraulic fracture across the coal-rock interface. (2) As the vertical distance between the horizontal well and coal-rock interface decreases, the breakdown pressure of perforation decreases; while the injection pressure increases when the hydraulic fracture crosses the coal-rock interface. (3) For the indirect fracturing engineering in 3# coal seam in Xinjing mine, the vertical distance between the horizontal well and coal-rock interface should not be larger than 2.0m to make the hydraulic fracture propagate into the coal seams.

Blind deconvolution (BD) is one of the effective methods that help pre-process vibration signals and assist in bearing fault diagnosis. Currently, most BD methods design an optimization criterion and use frequency or time domain information independently to optimize a deconvolution filter. It recovers weak periodic impulses related to incipient faults. However, the random noise interference may cause the optimizer to overfit. The time-domain-based BD methods tend to extract fault-unrelated single peak impulse, and the frequency-domain-based BD methods tend to retain the maximum energy frequency component, which will lose the fault-related harmonics frequency components. To solve the above issue, we propose a hybrid criterion that combines the kurtosis for time domain optimization and the $G-l_1/l_2$ norm for the frequency domain. These two criteria are monotonically increasing and decreasing, so they mutually constrain to avoid overfitting. After that, we design a multi-task one-dimensional convolutional neural network with time and frequency branches to achieve an optimal solution for this hybrid criterion. The multi-task neural network realizes the simultaneous optimization of two domains. Experimental results show that our proposed method outperforms other state-of-the-art methods.

The restriction of normal blood flow is the cause of many diseases including stroke and coronary artery diseases. To study the consequences of vessel blockade, previous models mainly focused on major arteries and have been well studied. However, the sequela from interruption of capillary vessels by microemboli was less well characterized. In this study, we exploited polystyrene microspheres as a mimicry of microemboli and found that microspheres of this size can be trapped in capillary vessels of all organs without causing apparent acute morbidities of the host. Interestingly, we accidentally found significantly increased recruitment of monocyte to the brain vasculature expressing low levels of Ly6C expression, but not to other organs. Further study revealed the spleen is the major origin of the recruited monocyte. Most importantly, VCAM-1 which is constitutively expressed on mouse brain vasculature orchestrates the recruitment of monocyte. Blockade of VCAM-1 in mice can substantially reduce monocyte recruitment. Interestingly, monocytes get activated through TNF- signaling which likely happens in the spleen instead of the brain. Collectively, we found a unique monocyte recruitment strategy in the brain comparing to other orangs, in response to capillary blockade induced by polystyrene microspheres.

As an implementation of inverse Radon transform, the Second-order Divided-difference Back Projection (SDBP) technique has been proposed in this paper, by which the accurate CT reconstruction can be theoretically realized. A computational model for CT reconstruction filter expressions has been derived on the basis of SDBP technique. The method reveals the correlation between the convolution kernel for data restoration and the filter expression. By substituting kernel functions into the computational model, the amplitude sequences of a variety of filters can be calculated. On the proposed filter construction method, the decomposition form of filters has been discovered, where a series of basic filters have been acquired. The properties of any filter depend on the decomposed basic filters. Basic filters can be used to compose filters in actual needs.

Gastric mixing relies both on enzymatic reactions and mechanical solicitations through antral contraction waves (ACWs). This work aims at discussing the influence of ACWs frequency and digesta viscosity on human gastric mixing efficiency by comparison with that of a soft elastic reactor (SER), that induces mixing by vibration of its wall in a similar way as ACWs promote stomach motility. The SER mixing curve was considered in order to determine the flow regime reached during gastric mixing. The number of contractions required to achieve homogenization was found to depend on the viscosity of the stomach content and the ACWs amplitude. Moreover, it was deduced from the same range of SER and ACWs operating points that the mechanical solicitation provided by human peristalsis was low and that gastric mixing was confined in laminar regime. Further efforts are needed to investigate the role of other physiological processes such as gastric secretions and emptying in overall gastric mixing performance.

Alloy 800H stands as one of the few code qualified materials for fabricating in core and out of core components operating in high temperature reactors (HTRs). Welding is a common practice for assembling these components, however, the election of a suitable filler material is essential to enhance the high-temperature creep resistance of Alloy 800H weldments in high temperature applications. In this study, Inconel 625 and Haynes 230 filler material were used to weld the Alloy 800H plates employing the Gas Tungsten Arc Welding (GTAW) technique. The high temperature tensile, creep rupture property, microstructural stability and evolution of the weldments after high temperature exposure were investigated and compared with Alloy 800H. The results showed that the both weldments exhibited enhanced tensile and creep behavior at 760 oC. The creep rupture time of the weldments with Inconel 625 filler and Haynes 230 filler materials was about two and three time longer than that of Alloy 800H base metal when tested at 80 MPa and 760 oC, respectively. Carbides (MC and M23C6) were commonly observed in the microstructure of both the weld and base metals in the two weldments after high temperature creep tests. However, the Inconel 625 filler weldment displayed detrimental δ and Laves phase in the fusion zone and these precipitates could be potential sites for initiating cracks following prolonged high temperature exposure. The study showed that the weldment with Haynes 230 exhibited better phase stability and creep rupture property than the one with Inconel 625 filler material, suggesting its potential as a candidate filler material for Alloy 800H for further investigation. The finding also emphasizes the critical consideration of microstructural evolutions and phase stability in evaluating high temperature materials and their weldments in high temperature reactor applications.

Objective: To evaluate the effect of propofol combined with psychological intervention on pain and emotional evaluation in painless colonoscopic colonic polypectomy patients undergoing endoscopic mucosal resection (EMR).Methods: A total of 80 patients who underwent painless colonoscopic colonic polypectomy with EMR treatment between June 2020 and June 2022 were selected in order of admission and divided into two groups. The control group received conventional analgesia, while the observation group received propofol combined with psychological intervention. Pain visual analog scale (VAS) and emotional scale were used to evaluate pain and emotions in both groups of patients. Adverse reactions and clinical efficacy were also compared between the two groups.Results: The two groups of patients were generally comparable with no significant differences (P > 0.05). The VAS score in the observation group was significantly lower than that in the control group (P < 0.05), and the emotional scale score was also improved compared to the control group (P < 0.05). The number of patients with adverse reactions in the observation group was less than that in the control group. The clinical effective rate in the observation group was significantly higher than that in the control group (P < 0.05).Conclusion: Propofol combined with psychological intervention can effectively alleviate pain and improve emotional status in painless colonoscopic colonic polypectomy patients undergoing EMR treatment, thereby increasing the comfort and success rate of the surgery. The number of patients with adverse reactions in the observation group was less than that in the control group, and the clinical effective rate in the observation group was significantly higher than that in the control group (P < 0.05).

This paper aims to build up a preference function to evaluate the public benefits of the type of agricultural farming, biodiversity, water provisions, land use type, ecotourism modes, and a monetary attribute (environmental trust fund and willingness to contribute) associated with an ecosystem service and land use program in a forest park. This study used the choice experiments to build a random utility model, analyze the average preference for the above land use attributes based on the conditional logit and used a latent class model to test the resident’s heterogeneous preferences for land use planning in the forest park. We also estimated the welfare derived from various land use programs. The empirical result had shown that: (1) increasing organic farming area, maintaining the status quo of species biodiversity, increasing the surface water provision, increasing the area of custom flora, increasing the wetland area, and setting up an integrated framework for ecotourism increase the public’s preference for the land use program; (2) we found that farmer and non-farmer haven’t the same land use preferences; (3) the ecotourism development program incorporating biodiversity, organic farming, ethnobotany, and wetland area with integrated ecotourism are more preferred than other land use program scenarios.

Shale gas reservoirs (SGR) are important replacements for conventional energy resources and have been widely exploited by hydraulic fracturing technologies. On the one hand, due to the inherent ultra-low permeability and porosity, there is stress sensitivity in the reservoirs generally. On the other hand, hydraulic fractures and the stimulated reservoir volume (SRV) generated by the massive hydraulic fracturing operation have contrast properties with the original reservoirs. These two phenomena bring huge challenges in SGR transient pressure analysis. Although some works in the literatures have been done on the transient pressure analysis of multi-fractured horizontal wells in SGR, unfortunately, none of them has taken the stress sensitivity and spatially varying permeability of SRV zone into consideration simultaneously. To fill this gap, this paper first idealizes the SGR to be four linear composite regions. What’s more, SRV zone is further divided into sub-sections on the basis of non-uniform distribution of proppant within SRV zone which easily yields spatially varying permeability away from the main hydraulic fracture. The stress sensitivity is characterized by the varying permeability depended on the pore pressure. By means of perturbation transformation and Laplace transformation, an analytical multi-linear flow model (MLFM) is obtained and validated by the comparison with the previous model. On the basis of our model, the flow regimes are identified and the sensitivity analysis of critical parameters are conducted to further understand the transient pressure behaviors. The research results provided by this work are of significance for well test interpretation and production performance analysis of SGR.

The ATP-binding cassette (ABC) transporter ABCG2 is a significant urate transporter with a high capacity, and it plays a crucial role in the development of hyperuricemia and gout. Therefore, it has the potential to be targeted for therapeutic interventions. Cortex Fraxini, a traditional Chinese medicine (TCM), has been found to possess anti-hyperuricemia properties. However, the specific constituents of Cortex Fraxini responsible for this effect are still unknown, particularly the compound that is responsible for reducing uric acid levels in vivo. In this study, we propose a target screening protocol utilizing bio-affinity ultrafiltration mass spectrometry (BA-UF-MS) to expediently ascertain ABCG2 ligands from the plasma of rats administered with Cortex Fraxini. Our screening protocol successfully identified fraxin as a potential ligand that interacts with ABCG2 when it functions as the targeted protein. Subsequent investigations substantiated fraxin as an activator of ABCG2. These findings imply that fraxin exhibits promise as a drug candidate for the treatment of hyperuricemia. Furthermore, the utilization of BA-UF-MS demonstrates its efficacy as a valuable methodology for identifying hit compounds that exhibit binding affinity towards ABCG2 within TCMs.

G protein-coupled receptor 15 (GPR15, also known as BOB) is an extensively studied orphan GPCR involving HIV infection, colonic inflammation and smoking-related diseases. Recently, GPR15 was deorphanized and its corresponding natural ligand demonstrated an ability of inhibiting cancer cell growth. However, no study reported the potential role of GPR15 in a pan-cancer manner. Using large-scale publicly available data from the Cancer Genome Atlas (TCGA) and the Genotype-Tissue Expression (GTEx) databases, we found that GPR15 expression is significantly lower in colon adenocarcinoma (COAD) than in normal tissues. And among 33 cancer types, GPR15 expression is significantly correlated with the prognoses of COAD, neck squamous carcinoma (HNSC), lung adenocarcinoma (LUAD) positively and stomach adenocarcinoma (STAD) negatively. This study also revealed that commonly upregulated gene set in the high GPR15 expression group (stratified via median) of COAD, HNSC, LUAD and STAD are enriched in immune systems, indicating that GPR15 might be considered as a potential target for cancer immunotherapy. Furthermore, we modelled the 3D structure of GPR15 and conducted the structure-based virtual screening. The top 8 hits compounds were screened and then subjected to molecular dynamics (MD) simulation for stability analysis. Our study provided novel insights into the role of GPR15 in a pan-cancer manner and discovered a potential hit compound for GPR15 antagonists.

The mitigation of NLOS (non-line-of-sight) propagation conditions is one of main challenges in wireless signals based indoor localization. When RFID localization technology is applied in applications, RSS fluctuates frequently due to the shade and multipath effect of RF signal, which could result in localization inaccuracy. In particularly, when tags carriers are walking in LOS (line-of-sight) and NLOS hybrid environment, great attenuation of RSS will happen, which would result in great location deviation. The paper proposes an IMU-assisted (Inertial Measurement Unit) RFID based indoor localization in LOS/NLOS hybrid environment. The proposed method includes three improvements over previous RSS based positioning methods: IMU aided RSS filtering, IMU aided LOS/NLOS distinguishing and IMU aided LOS/NLOS environment switching. Also, CRLB (Cramér-Rao Low Bound) is calculated to prove theoretically that indoor positioning accuracy for proposed method in LOS/NLOS mixed environment is higher than position precision of only use RSS information. Simulation and experiments are conducted to show that proposed method can reduce the mean positioning error to around 3 meters without site survey.

Objectives: The purpose of this study is to determine the association between umbilical venous blood flow (UVBF) to placental pulsatility index (PPI) ratio and gestational age (GA) in women undergoing prenatal assessments and adverse pregnancy outcome (APO) screening Methods: Between January and December 2022, sonographic examinations were conducted to assess the fetal umbilical cord insertion site in singleton fetuses, and hemodynamic indices of the umbilical artery, umbilical vein, and uterine artery were computed. Through regression analysis, we derived the optimal regression equation to elucidate the UVBF/PPI ratio parameters based on GA. Results: Among 492 singleton fetuses between 21+0 and 40+6 weeks of gestation in the final study. The average fetal UVBF/PPI ratio was 180.45±119.32. Correlation analysis revealed a positive relationship between the UVBF/PPI ratio and GA(p = .000). Using regression analysis, the best-fit regression equation was the linear function model, which explains the value of UVBF/PPI ratio parameters based on GA. Lower UVBF/PPI ratio revealed a positive relationship in the low birth weight fetuses (p=0.021) and higher preterm delivery rate (p=0.034). Cerebroplacental ratio (CPR) showed a high correlation with the UVBF/PPI ratio (r=0.471, p=0.000). Conclusions: The findings of our analyses revealed that contribute to our understanding of fetal hemodynamics and highlight the potential of UVBF/PPI ratio as a predictive marker for adverse pregnancy outcomes, such as preterm birth, low birth weight, or potential fetal hypoxemia. It might be useful for prenatal counseling and clinical purposes.

An eight-sided prism sample, obtained from a hot-rolled AZ31 magnesium alloy sheet, was compressed at room temperature along the transverse direction to investigate the influence of local strain on twinning behavior using electron backscatter diffraction (EBSD) measurements. The octagonal surface of the sample was divided into distinct regions based on hardness distribution and metallographic observations. The EBSD maps of different areas show significant variations, suggesting that these areas experienced different local strain conditions. The EBSD measurements provided detailed data from three distinct regions, with the strain state known in two regions and uncertain in the third. The combined analysis of the Schmid factor (SF) and the strain compatibility factor (m') was employed to study twin variant selection. The comparison of twinning behavior in different regions showed that the strain compatibility factor offered a more comprehensive explanation for the observed twinning pattern in the region with local shear strain.

In this work, the recently proposed cracking elements method (CEM) is used for simulating the damaging processes of structures with initial imperfections. CEM is built in the framework of conventional FEM which is formally like a special type of finite element. The disconnected piecewise cracks are used for representing crack paths. Taking the advantages of CEM that both the initiations and propagations of cracks can be naturally captured, we numerically study the uni-axial compression tests of specimens with multiple joints and fissures, where the cracks may propagate from the tips, or from some other unexpected positions. Though uni-axial compression tests are considered, mainly tensile damage criteria are used in the numerical model. On one hand, the results demonstrate the robustness and effectiveness of the CEM while on the other hand, some drawbacks of the present model are demonstrated, showing the future work.

This study chose the indoor soil column test as the main method and the field test as the validation test to investigate the effects of various straw mulching techniques (surface, deep and straw mulching + deep burial) on evaporation and salt dynamics in saline soils. The results showed that straw mulching treatment could effectively reduce soil water evaporation, promote desalination in the stage of leaching infiltration and alleviate salt return in the stage of water evaporation, and the effect of straw mulching + deep burial treatment was better than that of single-layer straw mulching treatment. The indoor soil column test showed that S2D1 treatment (a 2:1 ratio of soil surface cover to the amount of straw buried 40cm below the soil surface) had the best effect on the suppression of soil moisture evaporation, and the cumulative evaporation of soil moisture was reduced by 65.85% compared with that of the CK, and the rate of salinity return in the evaporation stage was effectively reduced by 92.04% compared with that of the CK. In addition, there is a significant positive correlation between cumulative evaporation of soil moisture and cumulative soil salinity, which implies that cumulative soil salinity increases with cu-mulative evaporation of soil moisture. The results of the field experiment were consistent with the soil column test, and the S2D1 treatment was able to maintain high soil moisture content in all soil layers in all periods of the experiment and kept soil salinity in the 0-40 cm soil layer at a low level. However, in the 40-80 cm soil layer, the soil salinity suppression effect of DB treatment (straw buried at 40 cm below soil surface) was the best. So in summary, the S2D1 treatment had the best salinity and evapo-transpiration suppression effect in saline soils. This study is of great significance for the resource uti-lization of straw waste, improvement of water utilization and efficiency, and soil salinization manage-ment.

Surface initiated atom transfer radical polymerization (SI-ATRP) is one of the most versatile technique to modify the surface properties of material. Recent developed metal free SI-ATRP makes such technique more widely applicable. Herein photo-induced metal-free SI-ATRP of methacrylates, such as methyl methacrylate, N-isopropanyl acrylamide, and N,N- dimethylaminoethyl methacrylate, on the surface of SBA-15 was reported to fabricate organic-inorganic hybrid materials. SBA-15 based polymeric composite with adjustable graft ratio was obtained. The structure evolution during the SI-ATRP modification of SBA-15 was monitored and verified by FT-IR, XPS, TGA, BET, and TEM. The obtained polymeric composite showed enhanced adsorption ability for the model compound toluene in aqueous. This procedure provides a low cost, ready availability, and facile modification way to synthesize the polymeric composites without the contamination of metal.

To further explore the bearing capacity and sustainable construction of vacuum drainage pipe (VDP) piles, field tests were carried out to compare and analyze the ultimate single pile bearing capacity, pile side friction and pile end resistance of ordinary piles and vacuum drainage pipe piles. The effect of the VDP pile on energy conservation and emission reduction in practical projects is discussed. The results shows that the VDP pile basically eliminated the soil squeeze and did not cause excessive relative displacement of pile and soil after vacuum consolidation. The VDP pile enhances pile side friction resistance, resulting in a 17.6% increase in ultimate bearing capacity compared to traditional piles. The VDP pile method can reduce carbon emissions by 31.4% compared to traditional methods. This study provides guidance for the production and design of VDP piles in the future and demonstrates their potential for energy conservation and emission reduction benefits compared to traditional methods.

Our aim was to evaluate efficacy and safety of 30mL CaO alone or plus Asc in bowel preparation before colonoscopy. Two hundred and forty six patients were allocated randomly to ingest 2L PEG with 30mL CaO, 1L PEG with 30mL CaO plus 5g Asc, or 3L PEG. We used Boston Bowel Preparation Scale (BBPS) to evaluate bowel preparation efficacy. We also determined other outcomes such as procedure time, polyp or adenoma detection rate and adverse events (AEs). Of 282 patients recruited, 36 were excluded. Groups were matched for baseline characteristics except weight (P = 0.020) and body mass index (BMI) (P = 0.003). Patient’s satisfaction were higher in 2L PEG-CaO (P = 0.016) and 1L PEG-CaO-Asc groups (P = 0·017). Patients’ compliance was 67.5%, 71.4% and 80.5% in 3L PEG, 2L PEG-CaO and 1L PEG-CaO-Asc groups (P = 0.014). Adequate bowel preparation rate was 75%, 78.57% and 53.66% in 3L PEG, 2L PEG-CaO and 1L PEG-CaO-Asc groups (P = 0.021). There were no differences in terms of remaining outcomes. Despite an increase in patients’ satisfaction and compliance, 1L PEG-CaO-Asc significantly decreased adequate bowel preparation rate. However, 2L PEG-CaO improved the patients' satisfaction and compliance and increased adequate bowel preparation rate.

Underwater target detection is widely used in various applications such as underwater search and rescue, underwater environment monitoring, and Marine resources survey. However, the visibility of the underwater environment and the accuracy of target detection can be affected by complex underwater light changes and unpredictable background noise. To address these issues, we propose an improved underwater target detection algorithm based on YOLOv8n. Our algorithm focuses on three aspects. Firstly, we replace the original C2f module with Deformable Convnets v2 to enhance the adaptive ability of the target region in the convolution check feature map and extract the target region's features more accurately. Secondly, we introduce SimAm, a non-parametric attention mechanism, which can deduce and assign three-dimensional attention weights without adding network parameters. Lastly, we optimize the loss function by replacing the CIOU loss function with the Wise-IOU loss function. To conduct our experiments, we create our own dataset of underwater target detection for experimentation. Meanwhile, we also utilized the Pascal VOC dataset to evaluate our approach. The [email protected] and [email protected]:0.95 of the original YOLOv8n algorithm on the underwater target detection were 88.6% and 51.8%, respectively, and the improved algorithm [email protected] and [email protected]:0.95 can reach 91.8% and 55.9%. The original YOLOV8n algorithm was 62.2% and 45.9% [email protected] and [email protected]:0.95 on the Pascal VOC dataset, respectively. The improved YOLOV8n algorithm [email protected] and [email protected]:0.95 were 65.7% and 48.3%, respectively. The floating-point computation volume of the model is reduced by about 6%. The above experimental results prove the effectiveness of our method.

In large-capacity energy storage systems, instructions are decomposed typically using an equalized power distribution strategy, where clusters/modules operate at the same power and durations. When dispatching shifts from stable single conditions to intricate coupled conditions, this distribution strategy inevitably results in increased inconsistency and hastened system aging. This paper presents a novel differentiated power distribution strategy comprising three control variables: the rotation status, the operating boundaries for both Depth of Discharge (DOD) and C-rates (C) within a control period. The proposed strategy integrates an aging cost prediction model developed to express the mapping relationship between these control variables and aging costs. Additionally, it incorporates the multi-colony particle swarm optimization (Mc-PSO) algorithm into the optimization model to minimize aging costs. The aging cost prediction model consists of three functions: predicting health features (HFs) based on the cumulative charge/discharge throughput quantity and operating boundaries, characterizing HFs as comprehensive scores, and calculating aging costs using both comprehensive scores and residual equipment value. Further, we elaborated on the engineering application process for the proposed control strategy. In the simulation scenarios, this strategy prolonged the service life by 14.62%, reduced the overall aging cost by 6.61%, and improved module consistency by 21.98%, compared with the traditional equalized distribution strategy. In summary, the proposed strategy proves effective in elongating service life, reducing overall aging costs, and increasing the benefit of energy storage systems in particular application scenarios.

Biomimetic design has recently received widespread attention. Inspired by the Terebridae structure, this paper provides a structural form for suppressing vortex-induced vibration (VIV) response. Four different structural forms are shown, including the traditional smooth cylinder (P0), the Terebridae-inspired cylinder with a helical angle of 30° (P30), the Terebridae-inspired cylinder with a helical angle of 60° (P60), and the Terebridae-inspired cylinder with a helical angle of 90° (P90). And computational fluid dynamics (CFD) method is adopted to solve the flow pass the Terebridae-inspired structures, and the vibration equation is solved using the Newmark-β method. The results show that the VIV responses are effectively controlled in the lock-in region for P30, P60, and P90, and P60 shows the best VIV suppression performance. The transverse amplitude and the downstream amplitude can be reduced by 82.67% and 91.43% respectively for P60 compared with that for P0, and the peak of the mean-drag coefficient is suppressed by 53.33%. The Q-criterion vortices of P30, P60, and P90 are destroyed, with irregular vortices shedding. It is also found that the boundary layer separation is located on the Terebridae-inspired ribs. The twisted ribs cause the separation point to constantly change along the spanwise direction, resulting in the development of the boundary layer separation being completely destroyed. The strength of the wake flow is significantly weakened for the Terebridae-inspired cylinder. In the lock-in region, the motion trajectory presents a typical 8-shaped for P0, while the motion trajectory of the Terebridae-inspired cylinder tends to be a flat 1-shaped.

In recent years, cemented tailings/paste backfill (CPB) become more and more important to maintain mine structure and keep mining stope to be stable in deep underground mining. Deep mining process often accompanied by blasting, rock burst and other high-speed dynamic loading. So it’s important to make research on dynamic behavior and characteristics of CPB. In this paper, a series of dynamic loading tests on CPB specimens by SHPB were taken to study the characteristic of stress-strain, dynamic strength, deformation and failure of CPB. The experimental results revealed that some CPB specimens have 1~2 lower stress peaks after reaching the peak stress before getting completely failed. The greater the cement-sand ratio was, the more obvious of strain reaction was. This property mainly showed like follows. The greater the cement-sand ratio was, the greater the dynamic compressive strength was under similar velocity impact; the dynamic compressive strength and the average strain rate were quadratic equation relationship, and the greater the cement-sand ratio was, the higher increase rate of dynamic compressive strength caused by strain rate. The dynamic compressive strength enhancement factor increased with the increase of the strain rate, and is larger than that of rock samples. The failure forms of CPB specimens under low-speed impact were almost the same as them under static uniaxial and triaxle compression. The CPB specimens were crushed broken under the critical strain rate, similar to the failure mode of low strength concrete. The experimental research results will improve our understanding the dynamic mechanical property of CPB and help to guide the strength design of deep mining backfill.

The present study was to investigate effects of total flavonoids from Taraxacum mongolicum Hand.-Mazz. (FT) on fermentation quality, antioxidant status and microbial community of Caragana korshinskii Kom. (CK) silage. CK was ensiled with no additive (CON), 1% FT and 2% FT on a fresh weight (FW) basis for 60 days. The results showed that 1% FT and 2% FT groups displayed higher DM content than CON group, and 2% FT group had the best effect on nutrient preservation. Compared with CON and 1% FT groups, 2% FT group exhibited the best silage fermentation quality and the highest antioxidant activity, including increased lactic acid, acetic acid concentrations and the activities of antioxidant enzymes, as well as decreased pH and the ammonia nitrogen (NH₃-N) concentration. Moreover, 2% FT addition significantly affected the microbial community, such as increased abundance of Lactobacillus and decreased abundances of Pseudomonas and unidentified Cyanobacteria. The abundances of Lactobacillus parafarraginis and Lactobacillus brevis were negatively correlated to pH, while they were positively correlated with T-AOC, GSH-Px and CAT activities. In conclusion, 2% FT may be used as additives to inhibit the growth of undesirable microorganisms and promote fermentation quality and antioxidant activity of CK silage.

TiO2-based building materials have air purification, auto-cleaning and sterilization functions, and these innovative green building materials have great potential for energy-saving and emission reduction applications in the future. However, there are still great challenges in improving photocatalytic efficiency and stability from laboratory to practical applications. In recent years, researchers have done a lot of work to improve the efficiency and stability of TiO2-based building materials. This paper briefly discussed the air purification principle by photocatalytic building, and the preparation techniques of TiO2-based building materials and the strategies to improve the efficiency of TiO2. Moreover, this paper has outlined the key factors that affect the photocatalytic building performance in practical applications, and analyzed the limitations and future development trends. Finally, we proposed some suggestions for further research on photocatalytic buildings and its application in practice, aiming to provide an efficient reference for developing highly efficient and stable photocatalytic building materials. The aim of this paper is to provide effective guidance for the application of TiO2-based photo-catalysts in the field of green buildings, helping to develop more efficient and stable low-carbon buildings for the development of sustainable cities.

Effectively mapping and monitoring rubber plantation is still changing. Previous studies have explored the potential of phenology features for rubber plantation mapping through a pixel-based approach (pixel-based phenology approach). However, in fragmented mountainous Xishuangbanna, it could lead to noises and low accuracy of resultant maps. In this study, we investigated the capability of an integrated approach by combining phenology information with an object-based approach (object-based phenology approach) to map rubber plantations in Xishuangbanna. Moderate Resolution Imaging Spectroradiometer (MODIS) data were firstly used to acquire the temporal profile and phenological features of rubber plantations and natural forests, which delineates the time windows of defoliation and foliation phases. Landsat images were then used to extract a phenology algorithm comparing three different approaches: pixel-based phenology, object-based phenology, and extended object-based phenology to separate rubber plantations and natural forests. The results showed that the two object-based approaches achieved higher accuracy than the pixel-based approach, having overall accuracies of 96.4%, 97.4%, and 95.5%, respectively. This study proved the reliability of a phenology-based rubber mapping in fragmented landscapes with a distinct dry/cool season using Landsat images. This study indicated that the object-based phenology approaches can effectively improve the accuracy of the resultant maps in fragmented landscapes.

Quantitative analysis of human gait is critical for early discovery, progressive tracking, and rehabilitation of neurological and musculoskeletal disorders, such as Parkinson’s Disease, stroke, and Cerebral Palsy. Gait analysis typically involves estimating gait characteristics, such as spatio-temporal gait parameters and gait health indicators (e.g., step time, length, symmetry, and balance). Traditional methods of gait analysis involve the use of cameras, wearables, and force plates, but are limited in operational requirements when applied in daily life - such as direct line-of-sight, carrying devices, and dense deployment. This paper introduces a novel approach for gait analysis by passively sensing footstep-induced floor vibrations during walking using vibration sensors mounted on the floor surface. Our approach is non-intrusive, scalable, and perceived as more privacy-friendly, making it suitable for continuous gait health monitoring in daily life. We developed a floor vibration-based gait analysis framework to estimate various gait parameters that are used as standard metrics in medical practices, including temporal parameters (step, stride, stance, swing, double-support, single-support time) and spatial parameters (step length, width, angle, stride length), and extracts gait health indicators (cadence/walking speed, left-right symmetry, gait balance, initial contact types). The main challenge is that floor vibrations are distinct across different floor types. To address this challenge, our approach develops floor-adaptive algorithms to extract floor-specific features and is designed to be generalizable to various settings, including homes, hospitals, and eldercare facilities. We evaluate our approach through real-world walking experiments with 20 adults with 12,231 labeled gait cycles across concrete and wooden floors. Our results show 90.5% (RMSE 0.08s), 71.3% (RMSE 0.38m), and 92.3% (RMSPE 7.7%) accuracy in estimating temporal, spatial parameters, and gait health indicators, respectively.

We suppose that a Cooper pair (CP) will experience a damping force exerted by the condensed matter. A Langevin equation of a CP in two dimensional condensed matter is established. Following a method similar to Nelson's stochastic mechanics, generalized Schr\"{o}dinger equation of a CP in condensed matter is derived. If the CPs move with a constant velocity, then the corresponding direct current (DC) electrical conductivity can be calculated. Therefore, a Drude like formula of resistivity of CPs is derived. We suppose that the damping coefficient of CPs in two dimensional cuprate superconductors is a linear function of temperature. Then the resistivity and scattering rate of CPs turn out to be also linear-in-temperature. The origin of linear-in-temperature resistivity and Planckian dissipation in cuprate superconductors may be the linear temperature dependence of the damping coefficient of CPs.

The pointing accuracy of large radio telescopes is affected by antenna structure errors, installation errors, servo errors, gravity, and varying environmental factors. It is hard to estimate the pointing error of radio telescopes under solar radiation via the traditional multi-parameter static pointing models, due to the time-varying characteristics of the dynamic pointing error. There is still no effective way to estimate the dynamic pointing error of large radio telescopes under solar radiation up to now. To estimate the dynamic pointing error of large radio telescopes under solar radiation, a new way based on digital twin(DT) is tried in this paper. The operational framework of the DT system of large radio telescopes is introduced first. Then, the Wuqing 70-m radio telescope(WRT70) is taken as the research object, the digital models of which are created. Finally, the reliability of the WRT70's DT system is verified and the dynamic pointing error of WRT70(staying at the position of the elevation angle of 90° and the azimuth angle of 180°) on two sunny days in different seasons is estimated by the created DT system. The research results show that the pointing error of large radio telescopes under solar radiation fluctuates greatly and the seasonal differences are very striking. The maximum elevation pointing error of WRT70 under solar radiation around the winter solstice is over 40 arcsec, which should never be ignored. The way is feasible to estimate the dynamic pointing error of large radio telescopes staying at a specific position under solar radiation via constructing a DT system in this paper, but it is not yet able to estimate effectively the dynamic pointing error of large radio telescopes being in action. It is expected to establish a dynamic pointing error model and calibrate the dynamic pointing errors of large radio telescopes being in action by DT technology in the future.

The thoracic surgery has increased drastically in recent years, especially in the light of the severe outbreak of 2019 novel coronavirus disease (COVID-19). Routine “passive” chest computed tomography (CT) screening of inpatients detects some pulmonary diseases requiring thoracic surgeries timely. As an essential device for thoracic anesthesia, the double-lumen tube (DLT) is particularly important for anesthesia and surgery. With the continuous upgrading of the DLTs and the widespread use of the fiberoptic bronchoscopy (FOB), the position of DLT in thoracic surgery is gradually becoming more stable and easier to observe or adjust. However, the DLT malposition still occurs during transferring patients from supine to lateral position in thoracic surgery, which leads to lung isolation failure and hypoxemia during one-lung ventilation (OLV). Recently some innovative DLTs or improved intervention methods have shown good results in reducing the incidence of DLT malposition. This review aims to summarize the recent studies of the incidence of left-sided DLT malposition, the reasons and effects of malposition, and summarize current methods for reducing DLT malposition and prospects for possible approaches. Meanwhile, we use bibliometric analysis to summarize the research trends and hot spots of the DLT research.

Recent prolonged dry periods and lack of irrigation water have severely affected the productivity of coffee farms’ in the Central Highlands of Vietnam. This paper analyzes the efficiency of irrigation water use for Robusta coffee (Coffea canephora) in Lam Dong province, Highlands, Vietnam. A Cobb-Douglas production function was used to determine coffee productivity’s response to the application of irrigation water and other production factors using data collected from 194 farmers while the Technical Efficiency (TE) and Irrigation Water Use Efficiency (IWUE) were analyzed using a Data Envelopment Analysis (DEA) model. The correlation of different factors to IWUE was determined using the Tobit model. The production function analysis using Cobb-Douglas shows that the volume of irrigation water, amount of working capital, labor and farm size significantly influence coffee productivity. It also shows that indigenous farmers are more efficient in utilizing irrigation water than the (mostly Kinh) migrant farmers. The Tobit result, on the other hand. indicates that farmers’ experience, education level, distance of farm to water source, security of access to water source, extension contact and credit access significantly affect IWUE. The study findings further suggest that mitigating water shortages in coffee farms require sub-regional and national policy support such as better access to credit and extension services, training, land management and household-level effort to improve farming practices, through the application of appropriate technologies and traditional knowledge.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

Objective: This study aimed to demonstrate the availability of portable devices for nasal FeNO measurement, which could replace exhaled NO measurement based on the continuous aspiration of multiple flow measurement systems. Methods: A descriptive cross-sectional study. The healthy subjects without rhinosinusis disorders (control group) and those with diagnosed allergic rhinitis (AR group) were enrolled in the study. They underwent nasal and bronchial FeNO measurements by both fixed flow NObreath® connected to nasal mask and multiple flows HypAir FeNO®. Results: A total of 153 people were recruited including 63 healthy subjects and 90 subjects with AR. There were no statistically significant differences in anthropometric characteristics between the two groups (P > 0.05). There were a significant increase in FeNO values in the AR group compared to the control group; concentrations of nasal and bronchial FeNO mearsured by NObreath® were 76.0 ± 50.7 ppb (vs 36.0 ± 28.1 ppb, P < 0.01) and 32.3 ± 15.4 ppb (vs 9.2 ± 5.6 ppb, P < 0.001), and those mearsured by NObreath® Hypair FeNO® were 1796.9 ± 523.3 ppb (vs 400.2 ± 123.1 ppb, P < 0.001) and 37.3 ± 23.0 ppb (vs 17.4 ± 18.3 ppb, P < 0.01). A weak correlation between the values measured by NObreath® and Hypair FeNO® devices was observed (r = 0.023 and r = 0.089, respectively; p < 0.05). Conclusions: The handheld NObreath® device is effective in measuring FeNO concentrations in both normal subjects and AR patients. The advantages in price and size, creating a compact, low-cost device that is convenient for use and research.

Collapsibility is an inherent characteristic of loess, which is often treated by adding industrial materials such as cement and lime in engineering, it seriously damages the reclamation performance of soil. Degradable calcium lignosulfonate (CLS) has a good prospect in balancing soil stabilization and environmental protection. Therefore, this paper evaluates the collapsibility and mechanical characteristics of CLS improved loess based on the collapsibility test, grey correlation analysis, and unconfined compressive strength test. The results show that when the content is 3%, the stabilization effect is most obvious, and the collapsibility coefficient can be reduced by more than 95%. The order of grey correlation degree of collapsibility on each index is moisture content, void ratio, dry density, and CLS content from large to small. The unconfined compressive strength increases rapidly in the first 14 days and then decreases with the content. When the content is too high, the strength of improved loess is lower than that of plain loess. Combined with SEM, microstructure parameters, and X-ray diffraction analysis, the carbonate minerals can play the role of filling pores and connecting soil particles, which reduces the grain size of mineral composition and the thickness of the electric double layer and makes the structure more compact. The research results have scientific significance and application value for the ecological modification research and engineering application of soil.

Ce-promoted NiMgAl mixed-oxide (NiCex-C, x = 0, 1,5,10) catalysts were prepared from the quaternary hydrotalcite precursors for CO2 hydrogenation to methane. By engineering the Ce contents, NiCe5-C showed its prior catalytic performance in low-temperature CO2 hydrogenation, being about 3 times higher than that of Ce-free NiCe0-C catalyst (TOF of NiCe5-C and NiCe0-C: 1.19 h-1 vs 0.39 h-1 @ 250 oC). With extensive characterization, it was found that Ce dopants promoted the reduction of NiO by adjusting the interaction between Ni and Mg(Ce)AlOx support. The higest ratio of surface Ni0/(Ni2+Ni0) was obtained over NiCe5-C. Meanwhile, the surface basicity was tailored with Ce dopants. The strongest medium-strength basicity and highest capacity of CO2 adsorption was achieved on NiCe5-C with 5wt% Ce content. The TOF tests indicated a good correlation with medium-strength basicity over the NiCex-C samples. The results showed that the high medium-strength and Ce-promoted surface Ni0 species endows the enhanced low-temperature catalytic performance in CO2 hydrogenation to methane.

A 'little brother' of pain, itch is an unpleasant sensation that creates a specific urge to scratch. To date, various machine-learning based image classifiers (MBICs) have been proposed for quantitative analysis of itch-induced scratch behaviour of laboratory animals in an automated, non-invasive, inexpensive and real-time manner. In spite of MBICs' advantages, the overall performances (accuracy, sensitivity and specificity) of current MBIC approaches remains inconsistent, with their values varying from ~50% to ~99%, for which the reasons underlying have yet to be investigated further, both computationally and experimentally. To look into the variation of the performance of MBICs in automated detection of itch-induced scratch, this article focuses on the experimental data recording step, and reports here for the first time that MBICs' overall performance is inextricably linked to the sharpness of experimentally recorded video of laboratory animal scratch behaviour. This article furthermore demonstrates for the first time that a linearly correlated relationship exists between video sharpness and overall performance (accuracy and specificity, but not sensitivity) of MBICs, and highlight the primary role of experimental data recording in rapid, accurate and consistent quantitative assessment of laboratory animal itch.

Plants of the golden Camellia group are not only high-quality camellia germplasm , but also a plant group with rich medicinal and nutritional value, which are used as food, cosmetics and traditional medicine in China. There are approximately 50 species in this group around the world, and more than 30 species of golden camelliaplants have been published in China. The leaves and flowers of these species have similar shapes, so they are often confused as species. Our study used simplified genome sequencing technology to construct a phylogenetic tree of plants in the Chinese golden Camellia group and describe the evolutionary relationships . At the same time, the secondary metabolic indexes of total phenols, total flavonoids, total anthocyanins and ellagic acid in the leaves were determined., and principal component clustering analysis was performed . The results showed that the chemical classification and genetic phylogenetic trees showed some of the same trends, indicating that Camellia chinensis can be used as Biomarkers for chemical type. The research results provide phylogenetic information for the genotype and performance diversity of golden camelliaregionally distributed in China. At the same time, molecular biology phylogenetic methods are used to understand or explain the characteristics of secondary metabolites of golden Camellia , and provide theoretical basis for the search and development of potential bioactive substances.

Xinjiang, as a climate-sensitive region in northwest China, holds significant importance in studying extreme weather events for agricultural production and socioeconomic development. Based on data from 52 meteorological stations and 23 extreme climate indicators in Xinjiang from 1960 to 2021, the 5a moving average, linear trend estimation, climate tendency rate, and GIS spatial analysis methods are used to analyze the distribution and change characteristics of extreme climate. The results revealed that from 1960 to 2021, TXx, TNx, TXn, TNn, FD, ID, TN10p, TX10p, and WSDI showed a significant upward trend, while SU, TR, TN90p, TX90p, and CSDI showed a significant downward trend. What is more, the range of changes in the extreme temperature indexes from 1990 to 2021 is higher than that of 1960 to 1989. The high-value areas of extreme indexes are primarily concentrated in the northern part, while the high-value areas of cold event indexes are mainly distributed in the southern part. The upward/downward trends all accounting for over 80.00% of the entire region. The Rx1day, Rx5day, PRCPTOT, R95p, R99p, R10, R20, and R25 showed a significant growth trend from 1960 to 2021, and the range of change in the extreme precipitation indexes from 1990 to 2021 was lower than that from 1960 to 1989. Moreover, their high-value areas and high climate tendency areas are mainly concentrated in the northern and western parts of Xinjiang, with upward trends all accounting for over 71.00% of the entire region. The research results provide theoretical foundations for formulating climate risk strategies in the northwest region of China.

For paramagnetic and elastic materials in the presence of quasi-static magnetic field, there is correspondingly quasi-static magnetic pressure, in contrast to the radiational electromagnetic pressure associated with electromagnetic momentum density. A thermodynamic pressure demagnetization is demonstrated. For the elastic dielectrics in the presence of quasi-static electrical field, its dual effect can be easily obtained by variable transformation.

Background: Recent researches have investigated the biological importance of RNA N1-methyladenosine (m1A) modifications in oncogenesis and progression of head and neck squamous cell carcinoma (HNSCC). However, whether m1A modifications also have latent effect in tumor microenvironment (TME) generation and immune regulation in HNSCC is unknown. Methods: We evaluated the m1A modification patterns and related to these modification patterns with TME cell infiltration features in 1041 HNSCC samples by bioinformatics approach. Results: The m1A score is an independent prognostic indicator. HNSCC patients with low m1A score group with poor overall survival (OS) was mainly characterized by stroma activation, lack of sufficient immune infiltration, and exhibited an immune- desert TME phenotype. Low m1A scores were also correlated with increased tumor mutation burden (TMB), and HNSCC patients with high TMB and low m1A scores had the worst OS. In addition, anti-CTLA-4 combined with anti-PD1 treatment was more effective in the high m1A score subgroup than in the low m1A score subgroup. Conclusions: This study revealed that m1A modifications play a non-negligible role in developing the TME versatility and complexity of HNSCC. Assessing m1A modification patterns in HNSCC helps improve our comprehension of its TME infiltration profile and guides more effective immunotherapeutic approaches.

Plants produce above- and below-ground biomass. However, our understanding of both production and decomposition of below-ground biomass is poor, largely because of the difficulties of accessing study materials. Below-ground organic matter decomposition studies are scanty and especially rare in the tropics. Here, we used a litter bag experiment to quantify the mass loss and nutrients dynamics of decomposing twigs and fine roots from an arbuscular mycorrhizal fungal associated tree, Parashorea chinensis, in a tropical rain forest in Southwest China. Overall, twig litter decomposed 1.9 times faster than fine roots (decay rate (k) twig=0.255, root=0.134). The difference in decomposition rates can be explained by a difference in phosphorus (P) concentration, availability and use by decomposers or C quality. Both materials showed an increase in N concentration, with final measurements still higher than initial levels. This suggests N may not be available due to microbial immobilization. Both carbon and nitrogen dynamics were significantly predicted by mass loss and showed a negative and positive relationship, respectively. Our study results imply that fine roots carbon and nitrogen contribute more to soils organic matter and enlarge the resident time. Therefore, better understanding of carbon cycle requires better understanding of mechanisms governing below ground biomass decomposition.

We report the strong coupling between plasmonic surface lattice resonances (SLRs) and photonic Fabry-Pérot (F-P) resonances in a microcavity embedded with two-dimensional periodic array of metal-insulator-metal nanopillars. For such a plasmonic-photonic system, we show that the SLR can be strongly coupled to the F-P resonances of both the odd- and even orders, and that the splitting energy reaches as high as 138 meV in the visible regime. We expect that this work will provide a new scheme for strong coupling between plasmonic and photonic modes.

Water pollution, intensified by the release of hard-to-degrade pollutants, poses severe threats to ecosystems, human health, and economic development. The existing advanced oxidation processes often involve high operational costs and may result in secondary pollution, highlighting the necessity for innovative and more sustainable solutions. To address these challenges, our study introduces a cost-effective and eco-friendly corona discharge barrier plasma discharger for wastewater treatment. Through the central composite design/response surface methodology, a high decolorization rate of 98% of methylene blue (MB) within 10 minutes was achieved by optimizing parameters such as pH and voltage. Furthermore, the mechanisms of the generation of reactive oxygen species via this device was discussed in detail and the degradation pathways of MB were described. Moreover, this device is also very energy-efficient, with a low energy density and electrical energy per order of 0.15 watt/mL and 5.79 kWh/m³/order, respectively. In conclusion, the plasma discharger developed in this study provides a cost-effective and environmentally sustainable solution for dye wastewater treatment. This research contributes significantly to the advancement of sustainable dye wastewater management practices, offering an innovative method that meets both environmental and economic objectives.

This paper draws upon the theory of turbulence in physics to explore the similarities and differences between volatility in financial markets and turbulent phenomena at a statistical physics level. By analogizing the dynamics of financial markets with fluid turbulence, we have developed an innovative analytical framework aimed at deepening the understanding of the complexity inherent in financial markets. Our research methodology includes a comparative analysis of simulated time series data for the Standard & Poor's 500 Index and fully developed turbulent velocity time series. We focus on the similarities in key statistical physical properties, including probability distributions, correlation structures, and power spectral densities. Furthermore, we have established a model of capital flow in financial markets and proposed corresponding solutions. Through computational simulations and data analysis, we find that while financial market volatility shares some statistical characteristics with turbulent phenomena, significant differences exist in the shapes of probability distributions and the temporal scales of correlations. This suggests that although financial markets exhibit patterns akin to turbulence, the behavior of this complex, multi-variable driven system does not completely correspond to natural turbulence, highlighting the limitations of directly applying turbulence theory to financial market analysis. Our study offers a new perspective for the theories of financial markets and the field of econophysics, providing fresh insights into the complexity of financial markets and contributing to the prevention and management of financial risk.

The spectra and global distributions of the X-ray emissions generated by the solar wind charge-exchange (SWCX) process in the terrestrial magnetosheath are investigated based on a global hybrid model and a global geocoronal hydrogen model. The solar wind O6+ ions which are the primary charge state for oxygen ions in solar wind are considered. The line emissivity of the charge-exchange born O5+ ions are calculated by Spectral Analysis System for Astrophysical and Lab oratory (SASAL). It is found that the emission lines from the O5+ ranges from 105.607 to 118.291 eV with the strong line at 107.047 eV. We then simulated the magnetosheath X-ray emission intensity distributions with a virtual camera at two positions of north pole and dusk at six stages during the passing of a perpendicular interplanetary shock combined with a tangential discontinuity structure through the Earth’s magnetosphere. During this process, the X-ray emission intensity increases with time, and the maximum value is 27.11 keV cm-2 s-1 sr-1 on the dayside, which is 4.5 times that before the solar wind structure reaches the Earth. A clear shock structure can be seen in the magnetosheath and moves earthward. The maximum emission intensity seen at dusk is always higher than that seen at north pole.

ALDH+ H1975 lung adenocarcinoma stem cells (LSCs) are a rare cell population identified in lung adenocarcinoma (LUAD). LSCs can self-renew, drive tumor initiation, growth, metastasis, and recurrence, and are also the predominant cause of poor prognosis due to their intrinsic resistance to drugs and chemotherapy. Consequently, LSCs are a promising target for LUAD therapy. Noncoding RNAs (ncRNAs), including microRNAs (miRNAs), long noncoding RNAs (lncRNAs), and circular RNAs (circRNAs), exert many significant regulatory functions in the pathogenesis of human cancers, showing the necessity for a comprehensive understanding of the mechanisms that underlie lung carcinogenesis. Nonetheless, research on many known transcripts and messenger RNAs (mRNAs) has already generated new information. Unknown biomarkers in ncRNAs and systematic and comprehensive interrelation with unknown ncRNAs and mRNAs may provide further insights into the biology of LUAD. Herein, a set of novel ncRNAs that include miRNAs, lncRNAs, circRNAs, were identified and differentially expressed patterns of ncRNAs and mRNAs in LSCs and ALDH- H1975 LUAD tumor cells (LTCs) were obtained using stringent bioinformatics pipelines. Through a meta-analysis of the identified landscapes, novel competitive endogenous RNA (ceRNA) networks were constructed to reveal the potential molecular mechanisms that regulate the hallmarks of LSCs and LTCs. This study presents a summary of novel ncRNAs and the fundamental roles of differentially expressed ncRNAs implicated in the activity of LSCs and LTCs. In addition, the study also provides a comprehensive resource for the future identification of diagnostic, therapeutic, and prognostic biomarkers in LUAD.

In order to realize the sustainable utilization of water resources and the sustainable development of economy, the evaluation index system of water use efficiency system and economic development system was constructed. Entropy weight method and comprehensive evaluation method were adopted to determine the index weights and conduct comprehensive evaluation for the two systems. The coupling coordination model was used to calculate the coupling degree, coordination degree and coupling coordination degree of the two systems. The annual coupling stage and coupling coordination intensity of the two systems were analyzed and determined. The results showed that the comprehensive evaluation values of both water use efficiency system and economic development system in Jinan City increased greatly from 2008 to 2017, and showed a changing trend of ups and downs. The two systems were in the antagonistic stage, and were gradually approaching the running-in stage, indicating that they were in the state of common development. The coupling coordination degree of the two systems gradually increased in waves, progressed from the moderately to the highly coordinated coupling. In the future, if the water control path appropriate to Jinan City can be explored actively, the water-saving kinetic energy of economic development can be increased constantly, and the linkage effect between economic development and water resources utilization can be given full play to, the two systems will be in the orbit with the benign interaction and healthy harmonious development.

Background: Coronavirus Disease 2019 (COVID-19) has been demonstrated to be the cause of pneumonia. Nevertheless, it has not been reported as the cause of acute myocarditis or fulminant myocarditis. Case presentation: A 63-year-old male was admitted with pneumonia and cardiac symptoms. He was genetically confirmed as having COVID-19 according to sputum testing on the day of admission. He also had elevated troponin I (Trop I) level (up to 11.37 g/L) and diffuse myocardial dyskinesia along with a decreased left ventricular ejection fraction (LVEF) on echocardiography. The highest level of interleukin-6 was 272.40 pg/ml. Bedside chest radiographs showed typical ground-glass changes indicative of viral pneumonia. Laboratory test results for viruses that cause myocarditis were all negative. The patient conformed to the diagnostic criteria of the Chinese expert consensus statement for fulminant myocarditis. After receiving antiviral therapy and mechanical life support, Trop I was reduced to 0.10 g/L, and interleukin-6 was reduced to 7.63 pg/ml. Moreover, the LVEF of the patient gradually recovered to 68%. The patient died of aggravation of secondary infection on the 33^rd day of hospitalization. Conclusion: COVID-19 patients may develop severe cardiac complications such as myocarditis and heart failure. This is the first report of COVID-19 complicated with fulminant myocarditis. The mechanism of cardiac pathology caused by COVID-19 needs further study.

Laser additively manufactured (LAM) Ti–6Al–4V alloy has huge application potential in aerospace structural parts such as turbine blades. However, there are few studies on the fatigue properties of such LAM parts under vibration loading, particularly with regard to anisotropy. In this paper, vibration fatigue properties of LAM Ti-6Al-4V by laser melted deposition process were investigated along the transversely deposited (TD) direction and parallelly deposited (PD) direction. Through the first-order bending vibration experiments, LAM Ti-6Al-4V alloy exhibits obvious anisotropic fatigue properties and significant dispersion in fracture position. The fracture morphology analysis reveals that the vibration fatigue failure was mainly dominated by the LAM process-induced defects and the microstructure. For the LAM samples without defects at crack initiation sites, the fatigue behavior is controlled by the prior β columnar grains with preferential orientation, which leads to enhanced fatigue crack propagation resistance for the PD samples. For the LAM samples with defects at initiation sites, having lower fatigue lives, the fatigue anisotropy strongly depends on the projection area of the lack-of-fusion defects relative to the loading direction, resulting in better fatigue performance for the TD samples.

The AREB/ABF (ABA response element binding) proteins in plants are vital for plant stress responses, but the understanding of AREB/ABFs in orchid species, an important traditional medicinal and ornamental plants, is limited. Here, twelve AREB/ABF genes were identified within three orchids’ complete genome and classified into three groups (groups I, II, and III) via a phylogenetic analysis, which was further supported by the analysis of their conserved motifs and gene structures. The cis-elements analysis showed that hormone response elements followed by light and stress responses were widely rich in AREB/ABFs. A prediction analysis of orchid ABRE/ABF-mediated regulatory network was further constructed through cis-regulatory elements (CREs) analysis of their promoter regions and revealed that several transcriptional factor (TF) gene family were abundant as the potential regulators for orchid AREB/ABFs. Expression profile analysis based on public transcriptomic data showed that most AREB/ABF genes have distinct tissue-specific expression patterns in orchid plants. Additionally, DcaABI5 as the homolog of ABA INSENSITIVE 5 (ABI5) from Arabidopsis was selected for further analysis. The results showed that Arabidopsis transgenic overexpressing DcaABI5 could rescue the ABA insensitive phenotype in the mutant abi5. Collectively, these findings will provide valuable information on AREB/ABF genes in orchids.

In China, there is an increasing need for greater genetic diversity in maize (Zea mays L.) germplasm and hybrids appropriate for mechanical harvesting. In order to test and distinguish American maize inbred lines with exceptional combining ability, four Chinese maize inbred lines (Chang7-2, Zheng 58, four-144 and four-287) were used to judge the combining ability and heterosis of 16 USA inbred lines by a NCII genetic mating method. The results showed that among the American inbred lines, 6M502A, LH208, NL001, LH212Ht, PHW51, FBLA and LH181 expressed good GCA for yield characteristics; while RS710, PHP76, FBLA, and PHJ89 showed excellent GCA for machine harvesting characteristics. Five hybrids (NL001 × Chang7-2, LH212Ht × Chang7-2, FBLA × four-144, LH181 × four-287, PHK93 × four-287) had better SCA values for yield characteristics, at 1.69, 1.07, 1.48, 1.84 and 1.05, respectively; while NL001 × Chang 7-2, 6M502A × Chang7-2, LH212Ht × Chang7-2, LH181 × four-287, PHW51 × Chang7-2 had better TCA values for yield characteristics, at 3.03, 2.80, 2.41, 2.19 and 1.91, respectively; NL001 × Chang7-2, 6M502A × Chang7-2, LH212Ht × Chang7-2, LH181 × four-287, PHW51 × Chang7-2 showed excellent Control Heterosis values, with 21.48%, 19.64%, 15.93%, 14.05% and 11.60% increases, respectively, compared to the check and potential for future utilization in Inner Mongolian corn production.

Vaccines trigger a complicated immunological response that includes B and T cells, with B cells producing antibodies. SARS-CoV-2 immunity weakens over time after vaccination. Discovering key changes in antigen-reactive antibodies over time after vaccination could help improve vaccine efficiency. In this study, we collected data on blood antibody levels in a cohort of healthcare workers vaccinated for COVID-19 and obtained 73 antigens in samples from four groups according to the duration after vaccination, including 104 unvaccinated healthcare workers, 534 healthcare workers within 60 days after vaccination, 594 healthcare workers between 60 and 180 days after vaccination, and 141 healthcare workers over 180 days after vaccination. An efficient machine learning based framework containing four feature selection methods (least absolute shrinkage and selection operator, light gradient boosting machine, Monte Carlo feature selection, and maximum relevance minimum redundancy) and four classification algorithms (decision tree, k-nearest neighbor, random forest, and support vector machine) was designed to screen out essential antigens. Several efficient classifiers with weighted F1 value around 0.75 were constructed. This study revealed that S1+S2, S1.mFcTag, S1.HisTag, S1, S2, Spike.RBD.His.Bac, Spike.RBD.rFc, and S1.RBD.mFc were most highly ranked among all features, where S1 and S2 are the subunits of Spike, and the suffixes represent the tagging information of different recombinant proteins. Meanwhile, the classification rules were extracted from the optimal decision tree to explain quantitatively the roles of antigens in the classification. This study identified antibodies associated with decreased clinical immunity based on populations with different time spans after vaccination. These antibodies have important implications for maintaining long-term immunity to SARS-CoV-2.

In recent years, due to the low energy utilization of the whole life-cycle of buildings and the di-minished indoor and outdoor comfort of buildings and the impact on the surrounding environ-ment caused by the carbon emissions of the building life-cycle, the establishment of a whole life- cycle carbon emission model for buildings to improve their energy utilization at all stages of their life-cycle has received unprecedented attention. In China, the construction industry has become a major carbon emitter, and traditional houses, as a green development building type, are an effec-tive way to achieve carbon neutrality in buildings, but the existing green building evaluation system lacks quantitative indicators of carbon emissions in the building life-cycle. The exclusive evaluation indexes for regional and characteristic buildings, such as traditional houses, are ne-glected; This study explored the formula for calculating the life-cycle carbon emissions model of traditional residential houses under a carbon emission intervention and used real measurements of the physical environment and comparative analysis of the limitations of existing local stand-ards; The results showed that the carbon emission calculation formulas for each stage of the life-cycle of traditional residential houses must be established by combining the selection of local building materials, and the materials for sustainable energy and carbon sinks of green systems. Based on the results of indoor and outdoor heat and humidity environmental tests of residential houses and an analysis of the limitations of existing evaluation indexes due to locality, four im-portant factors affecting locality green buildings in terms of energy utilization, site ecology and landscape, land saving and material saving were extracted; on this basis, the whole life-cycle carbon emission model of traditional residential houses is constructed by combining the existing green building evaluation standards with the carbon emission indexes of the life-cycle of tradi-tional residential houses.

Cycas (family Cycadaceae), spread throughout tropical and subtropical regions, is crucial in con-servation biology. Due to the subtle morphological variations between species, a solid spe-cies-level phylogeny for Cycas is lacking. Because of the rapid progress in high-throughput se-quencing technology, it has become feasible to acquire complete chloroplast (cp) genome se-quences, which provide a molecular foundation for phylogenetic research. In the present study, we employed next-generation sequencing technology to assemble and analyze the chloroplast genomes of six Cycas plants, including their genome structure, GC content, and nucleotide di-versity. The Cycas chloroplast genome spans 162,038 to 162,159 bp and contains 131 genes, in-cluding 86 protein-coding genes, 37 transfer RNA (tRNA) genes, and 8 ribosomal RNA (rRNA) genes. Through a comparative analysis, we found that the chloroplast genome of Cycas was highly conserved, as indicated by the contraction and expansion of the inverted repeat (IR) re-gions and sequence polymorphisms. In addition, several non-coding sites (psbK-psbI, petN-psbM, trnE-UUC-psbD, ndhC-trnM-CAU, and rpl32-trnP-GGG) showed significant varia-tion. The utilization of phylogenetic analysis relying on protein-coding genes has substantiated the division of Cycas primarily into four groups. The application of these findings will prove valuable in evaluating genetic diversity and the phylogenetic connections among closely related species. Moreover, it will provide essential support for the advancement of wild germplasm re-sources.

Supplementary lighting is commonly used in high-quality seedling production. In this study, grafted tomato seedlings were grown for 10 days in a glasshouse with a 16-hour daily supplementary lighting at 100 μmol·m⁻²·s⁻¹ PPFD from either high pressure sodium (HPS), metal halide (MH), far-red (FR), white LEDs (W), or mixed LEDs (W₁R₂B₁) to determine which light sources improve the seedling quality. The control did not have any supplementary light. The physiological parameters and the expression of genes related to photosynthesis were analyzed. The results show that the root length, biomass, number of leaves, chlorophyll (SPAD), dry weight to height ratio (WHR) of the scion, and specific leaf weight (SLW) were the greatest for grafted seedlings grown in W₁R₂B₁. The level of root ball formation was the greatest for seedlings grown in W₁R₂B₁, followed by those grown in W, HPS, and MH. Seedlings grown in FR did not fare very well, as they were very thin and weak. Moreover, the expression of two photosynthetic genes (PsaA and PsbA) was significantly increased by W₁R₂B₁ and W, which suggests that the plastid or nuclear genes might be regulated. The overall results suggest that W₁R₂B₁ was the most suitable light source to enhance the quality of grafted tomato seedlings. The results of this study could be used as a reference for seedling production in glasshouses, and provide new insights in the research of lights affecting the development of plants.

The genetic diversity of coronavirus (CoV) is high, and its infection in animals has not yet been fully revealed. By RT-PCR detection of partial RNA dependent RNA polymerase (RdRp) gene of CoV, we screened a total of 502 small mammals belonging to 18 species in 12 genera and 4 orders collected in Dali and Nujiang Prefecture of Western Yunnan Province, China. The prevalence of β-CoV in Chevrieri's field mouse (Apodemus chevrieri) and Lancangjiang field mouse (A. ilex) were 3.54% (4/113) and 6.67% (6/90), respectively; the prevalence of α-CoV in White-footed Indochinese rat (Rattus nitidus) and long-tailed red-toothed shrew (Episoriculus leucops) was 75% (3/4) and 5.88% (1/17), respectively. The co-infection rates of β-CoV and α-CoV in Kachin red-backed vole (Eothenomys cachinus), Norway rat (R. norvegicus) were 2.22% (2/90), 3.85% (1/26) respectively. The identity of the partial RdRp genes obtained of 13 strains of β-CoV was 83.42%-99.23% at nucleotide level, and it is worth noting that the two strains from Kachin red-backed vole showed highly homology to BOV-36/IND/2015 from Indian bovine and DcCoV-HKU23 from one-humped camel (Camelus dromedarius) in Morocco, the nucleotide similarity between 97.86%-98.33%. Similarly, the identity of the 7 strains of α-CoV among the partial RdRp sequences was 94.00%-99.18% at nucleotide levels. The viral load in different tissues was measured by quantitative RT-PCR (qRT-PCR). The average CoV viral load in small mammalian intestinal tissue was 1.25×106copies/g, differently, the mean CoV viral load in liver, heart, lung, spleen and kidney tissue was from 1.29×103 to 4.02×103copies/g, which revealed that CoV has extensive tropism of intestinal tissue in small mammals (P &lt; 0.0001). This result revealed the genetic diversity, epidemiology, and infective tropism of α-CoV and β-CoV in small mammals from Dali and Nujiang, which deepens the comprehending of the retention and infection of coronavirus in natural hosts.

In-depth insights into the profound impacts of climate change and human activities on water resources are garnered through the dynamic changes in surface water, a crucial aspect of effective water resource management and the preservation of aquatic ecosystems. This paper introduces an innovative approach employing the random forest algorithm for the systematic extraction and monitoring of surface water at large regional or national scales. This method integrates spectral bands, spectral indices, and digital elevation model data, offering a novel perspective on this critical task. A data filling model is proposed to mitigate the impact of missing data due to cloud cover. Leveraging the capabilities of the Google Earth Engine (GEE), detailed information on surface water dynamics during the rainy and dry seasons in the Yangtze River Basin (YRB) from 1991 to 2021 is extracted using Landsat time series imagery. The analysis encompasses spatial-temporal variation characteristics and trends, with a specific focus on the intricate interplay between the areal extent of surface water and hydro-meteorological factors in each sub-basin of the YRB. Importantly, this includes considerations of potential groundwater contributions to surface water. Key findings from our research include: (1) Achieving a remarkable overall accuracy of 0.96 ± 0.03 in obtaining reliable surface water datasets with the support of GEE. (2) Identifying significant trends, such as a noteworthy increase in rainy season surface water bodies (+248.0 km2·yr−1) and a concerning decrease in surface ice/snow cover during both rainy and dry seasons, with change rates of −39.7 km2·yr−1 and −651.3 km2·yr−1, respectively. (3) Uncovering the driving mechanisms behind these changes, revealing positive correlations between the areal extent of rainy season surface water bodies and precipitation, as well as negative correlations between surface ice/snow cover area and average surface skin temperature. It is crucial to note that these driving factors exhibit variation among secondary river systems, underscoring the complexity of surface water dynamics. Furthermore, comparative analyses with existing surface water products are conducted, contributing to a deeper understanding of the advantages and uncertainties inherent in our proposed extraction method. The proposed method for large-scale surface water extraction not only enhances the monitoring of spatio-temporal surface water dynamics in the YRB but also provides valuable insights for the sustainable utilization and protection of water resources, considering the potential role of groundwater in supplementing surface water.

This literature review paper delves into the synergies between Climate-Smart Agriculture (CSA) and the effective management of food losses. With the escalating challenges posed by climate change and the pressing need to address food security concerns, the intersection of these two critical domains becomes paramount for sustainable agricultural practices. The review explores existing research on the implementation of climate-smart agricultural techniques and their impact on mitigating food losses throughout the agricultural value chain. The paper synthesizes findings related to climate-resilient crop varieties, precision farming, water-use efficiency, and sustainable soil management, highlighting their contributions to reducing post-harvest losses and enhancing overall food security. In addition to summarizing current knowledge, this paper identifies gaps in the literature and proposes avenues for future research. This review serves as a foundation for researchers, policymakers, and practitioners seeking to contribute to the advancement of climate-smart agriculture and the reduction of food losses, paving the way for a more sustainable and resilient global food system.

Cross-field innovation in faba bean breeding has added significant value to the traditional faba bean planting industry by allowing for the selection of faba bean varieties with a dual purpose as ornaments and food. In order to improve the selection efficiency, we determined 17 phenotypes related to ‘dual purpose’ faba beans and evaluated 37 new breeding lines, which were bred for 10 years by our team, and two traditional faba bean varieties by means of an Analytic Hierarchy Process. The lines and varieties were evaluated and sorted into five grades, from which two breeding lines with excellent comprehensive phenotypes and dual ornamental and food functions were selected. The new line GS5 passed the identification of Crop Identification Committee of Chongqing Seed Industry Association on November 25, 2021 and was renamed "Doumei 1 hao" with the identification number of " 202111". The results confirmed that the comprehensive evaluation system constructed in this study can be used for the effective selection of dual-purpose faba bean lines, providing an empirical approach for strategic decision-making by breeders.

Chitosan (CTS) is widely used in agriculture as a soil amendment, plant growth regulator and promoter of cold resistance. However, the effects of CTS on strawberry seedlings under the combined stress of high-temperature and high-light are unclear. In this study, Xuelixiang strawberry was used as a test material, and 100 mg·kg-1 CTS solution was sprayed onto the leaves. We measured the chlorophyll content, membrane peroxidation, reactive oxygen species content, antioxidant enzyme content, AsA-GSH cycle activity and other related indicators of strawberry seedling leaves under the combined stress of high-temperature and high-light and found that CTS can increase the contents of antioxidants, increase the contents of osmotic adjustment substances, increase the activity of antioxidant enzymes activity,; remove reactive oxygen species over time, reduce the damage of reactive oxygen species to photosynthetic organs and cell membranes, and improve the photosynthesis efficiency of leaves of strawberry plants under high-temperature and high-light stress, thereby reducing damage to strawberry seedlings caused by high-temperature and high-light.

Abstract: The COVID-19 pandemic significantly disrupted global healthcare systems. The impacts of SARS-CoV-2 infection on urticaria and its management are unknown. To collect information about patients with urticaria infected with SARS-CoV-2 and to investigate the impact of SARS-CoV-2 infection on urticaria severity, course, and treatment to better support recovery. This was a questionnaire-based study of patients with urticaria infected with SARS-CoV-2. Changes in urticaria severity (measured with the urticaria activity score (UAS)), course, and treatment were assessed before, during, and after SARS-CoV-2 infection. Mean (± SD) UAS scores were 5.17 ± 1.67, 4.23 ± 1.98, and 4.37 ± 1.93 before, during, and after SARS-CoV-2 infection, respectively (F = 8.839, p < 0.01). The median (IQR) wheal score was 0.464 (0.464, 0.763), 0.464 (0.138, 0.763), and 0.464 (0.138, 0.763) before, during, and after infection, respectively (Kruskal-Wallis H-test, H=12.230, p = 0.02). The median (IQR) pruritus score was 0.695 (0.395, 0.695), 0.394 (0.123, 0.695), and 0.394 (0.123, 0.695) before, during, and after infection, respectively (Kruskal-Wallis H-test, H = 21.001, p < 0.01). Within the limitations of a questionnaire study, urticaria appears to improve during SARS-CoV-2 infection, worsens slightly after recovery, and the frequency of Western medicine use increases.

To conduct a precise impact assessment of marine diesel engines, a 200t floating impact platform was utilized to simulate realistic testing conditions. The testing generated the acceleration time curve and the impact response spectrum for the diesel engine. According to the applicable standards, the spectral velocity was chosen as the evaluation index, and an evaluation of the longitudinal, transverse, and vertical impact environment of the diesel engine was conducted. The shock factor interpolation method was corrected using the confidence interval based on normal distribution, and the interpolated confidence interval of the shock factor was determined. The findings reveal that: The 200t-class floating shock platform is capable of providing a reliable shock environment for diesel engine tests. The shock wave serves as the primary external force during the experiment, and the impact of bubble pulsation can be disregarded when assessing using the floating shock platform. To more accurately describe the experimental shock intensity when presented with dispersed data, the confidence interval can be utilized, and the resulting prediction formula provides a higher level of impact safety. The obtained conclusions can serve as a reference for predicting the shock environment of large shipboard equipment using the shock platform.

This article presents a comprehensive framework for valuing financial instruments subject to credit risk. In particular, we focus on the impact of default dependence on asset pricing, as correlated default risk is one of the most pervasive threats in financial markets. We analyze how swap rates are affected by bilateral counterparty credit risk, and how CDS spreads depend on the trilateral credit risk of the buyer, seller, and reference entity in a contract. Moreover, we study the effect of collateralization on valuation, since the majority of OTC derivatives are collateralized. The model shows that a fully collateralized swap is risk-free, whereas a fully collateralized CDS is not equivalent to a risk-free one.

The petrogenesis of high Ba-Sr granitoids provide a great significance to penetrate the Proto-Tethys evolution in the North Qilian orogenic belt. This paper presents a combination of zircon U-Pb age, whole-rock major and trace element concentrations, and Sr-Nd-Hf isotopic data for Caowa high Ba-Sr dioritic intrusion from the eastern part of the North Qilian orogenic belt, aiming to decipher its petrogenesis and tectonic setting. LA-ICP-MS zircon U-Pb dating yields an emplacement age of 447±3 Ma for the Caowa intrusion, indicating a magmatic activity of the late Ordovician. The Caowa quartz diorites contain moderate contents of SiO2, MgO, Mg# and resultant high concentrations of Na2O+K2O, Fe2O3T and Al2O3, displaying calc-alkaline and metaluminous characteristics. Their relatively elevated Ba (up to 1165 ppm) and Sr (561 to 646 ppm) contents, with obvious enrichment in LILEs (e.g. Ba、Th、U) and depletion in HFSEs (e.g. Nb、Ta、Ti) resemble those of typical high Ba-Sr granitoids in subduction zone. Together with enriched Sr-Nd isotopic compositons[(87Sr/86Sr)i=0.7082−0.7086, εNd(t)= -5.1 to -4.9], and relatively extensive εHf(t) values (-13.2 to +8.5) of zircons, it suggests that these high Ba-Sr quartz diorites were derived from a mixture magma source between the ancient crust materials and the enriched lithospheric mantle metasomatised by fluid was released from subducted oceanic crust or sediment. Taking into account the ophiolites, high pressure metamorphic rocks and arc magmatic rocks in the region, we infer that affected by the northward subduction of the Qilian Proto-Tethys ocean, the Laohushan oceanic crust of the North Qilian back-arc basin was subducted during the Late Ordovician and resulted in extensive metasomatism of lithospheric mantle by fluids derived from oceanic crust or sediments, and the Caowa high Ba-Sr quartz diorites generated in the process of crust-mantle interaction during the Late Ordovician.

Existing research concerning the effects of the sitting birth position during the second stage of labour on maternal and neonatal outcomes remains controversial, and there is a lack of studies to explore its effect on the childbirth experience. The objective of this study is to explore whether the sitting birth position would influence maternal and neonatal outcomes, as well as the childbirth experience reported by Chinese women using the Childbirth Experience Questionnaire (CEQ). A total of 296 women (including primiparous women and multiparous women) were enrolled in our study, and they were divided into the sitting position cohort (n=106) or the lithotomy position cohort(n=116). The study found that primiparous women in the sitting position cohort had a shorter duration of the second stage of labour, higher spontaneous vaginal birth rates, lower episiotomy rates and better childbirth experience (p<0.01). There was no significant difference for perineal lacerations, 2h-postpartum haemorrhage (P>0.05) between the two cohorts of primiparous women. After adjusting for confounding factors through multiple linear and logistic regression analyses, the results remained consistent with those reported above. No neonate in each cohort had Apgar scores at 1min and 5 min postpartum less than 7 or the Cord artery pH less than 7.00, regardless of parity. In addition, among multiparous women, there was no significant difference in any maternal and neonatal outcomes and women’s CEQ scores (p>0.05) between two cohorts. Based on the findings, we recommend that women could take the sitting birth position into account when giving birth for a positive childbirth experience, especially for primiparous women. The study could also serve as a reference for healthcare providers in the management of childbirth positions and the development of high-quality maternal care.

In this paper, the sol−gel method was used to synthesize powders of LaMnO3 (LMO), La0.85Ca0.15MnO3 (LCM), and La0.85Sr0.15MnO3 (LSM). We investigated the impact of substituting Ca and Sr at the A−site on the perovskite crystal structure and electrochemical capabilities of LMO. LCM retained its orthogonal structure in comparison to the parent LMO components, whereas LSM transitioned to a rhombic structure. At 0.5 A/g, the specific capacitance of LCM and LSM electrodes is 185.5 F/g and 248 F/g, respectively.The specific capacitance of LCM was more three times than that of the LMO electrode. Among the three samples (LMO, 22.25 m2 g−1; LSM, 31.56 m2 g−1), the LCM sample exhibited the highest specific surface area of 38.79 m2 g−1. The charge transfer resistances of the LMO, LCM, and LSM are 0.48 Ω, 0.36 Ω, and 0.38 Ω, correspondingly. The LCM electrode exhibits the greatest capacitance performance due to its more refined morphology, increased concentration of oxygen vacancy, and more complete utilization of the perovskite bulk structure. The above results demonstrate that Ca or Sr substitution of A−site compounds has great potential for supercapacitor applications.

Halide perovskite materials gain enormous attention for their semiconducting properties, higher power conversion efficiency and potential applications in a wide range field of studies along with their two key limitations: stability and toxicity. In spite of great progress made on the halide perovskites and many promising research developments, overcoming these limitations is not realized yet. Therefore, coordination engineering of new framework for obtaining alternative new halide perovskite materials and fundamental understanding of the coordination chemistry and electronic interactions forming the structure of these newly engineered halide perovskite materials might be one way in order to overcome the issues related to both stability and toxicity. In this review, the current development of halide perovskite families, both lead halide perovskites and lead free halide perovskites followed by coordination engineering of the new frameworks to engineer new halide perovskite materials will be reviewed comprehensively. Moreover, all the concerns of the fundamental ideas of coordination chemistry and electronic interactions that are keys in forming the halide perovskite structures are discussed in detail and form the main aim of this review. Interestingly, we also discuss recent potential energy applications beyond photovoltaic and this review has completed with an essential and open question: ‘what could happen in the future of halide perovskites?’ in order to excite commercial enterprises and research institutions again as well as to get motivating new predictions on the future continuity of this field.

Echinococcus granulosus is a harmful cestode parasite which could cause Cystic Echinococcosis in humans, various livestock species and wild animals. Calmodulin (CaM), a Ca²⁺ sensor protein, is widely expressed in eukaryotes and mediates a variety of cellular signaling activities. In our study, the CaM in Echinococcus granulosus (rEgCaM) was successfully cloned and the molecular and biochemical characterizations of rEgCaM were identified. The results showed that rEgCaM was a highly conserved calcium-binding protein, consisting of 149 amino acids. Immunoblot analysis revealed that rEgCaM could be identified using E. granulosus infected sheep serum. The usage of rEgCaM as antigen was evaluated by indirect ELISA which exhibited a high sensitivity of 90.3% but low specificity (47.1%). rEgCaM was mainly located in the tegument tissues and parenchymal region of protoscoleces, the tegument and inner body of adult worm and predominantly expressed in the germinal layer. The mRNA expression of rEgCaM in PSCs were gradually decreased with the increase death of PSCs. In electrophoretic mobility tests and ANS assays, rEgCaM showed a typical calcium-binding protein characteristics. This is the first report on CaM from E. granulosus and rEgCaM is considered to be involved in some important biological function of E. granulosus as a calcium-binding protein.

Objective: To study the factors affecting the time of umbilical cord shedding in premature infants.Methods: A total of 151 premature infants who were born in the obstetrics department of a Class III hospital in Hefei from November 2020 to June 2021 were selected as subjects. All premature infants and their families met the complete inclusion criteria. A total of 33 related factors from 3 aspects, including the birth situation of premature infants, the condition of premature infants in hospital and the condition of pregnant mothers, were collected for univariate analysis and multiple Logistic regression analysis. The relevant factors affecting the umbilical cord shedding time of premature infants were screened through the univariate analysis results, and the main factors affecting the umbilical cord shedding time of premature infants were screened through the multiple Logistic regression analysis results.it was found that the weight, gestural age, admission age, whether the premature infants were combined with NRDS, the use of antibiotics, the duration in the warm box, the initial temperature in the warm box, the duration of light therapy, the degree of Apgar for 1 minute, the maternal education level had an effect on the time of umbilical cord shedding of premature infants (P < 0.05). Through Logistic multiple regression analysis, it was screened that the duration of premature infants in the incubator was the main factor affecting the umbilical cord shedding time of premature infants (P < 0.05).Conclusion: Factors such as premature infants' weight, gestural age, admission age, whether they are combined with NRDS, antibiotic use, duration in the incubator, initial temperature in the incubator, duration of phototherapy, Apgar level of 1 minute, and maternal education level will affect the umbilical cord shedding time of premature infants. Among them, duration in the incubator is the main factor affecting the umbilical cord shedding time of premature infants.

Fifteen new diterpenoids, namely xishaklyanes A-O (1-15), along with three known related ones (16-18), were isolated from the soft coral Klyxum molle collected from Xisha Islands, South China Sea. The stereochemistry of the new compounds were elucidated by a combination of detailed spectroscopic analyses, chemical syntheses, quantum chemical calculations and comparison with the reported data. The absolute configuration of compound 18 was established by the modified Mosher's method for the first time. In bioassay, some of these compounds exhibited considerable antibacterial activities on fish pathogenic bacteria, and compound 4 showed the most effective activity with MIC of 0.225 g/mL against Lactococcus garvieae.

Functional connectivity (FC) is a potential candidate that can increase the performance of brain-computer interfaces (BCIs) in the elderly because of its compensatory role in neural circuits. However, it is difficult to decode FC by current machine learning techniques because of a lack of its physiological understanding. To investigate the suitability of FC in BCI for the elderly, we propose the decoding of lower- and higher-order FCs using a convolutional neural network (CNN) in six cognitive-motor tasks. The layer-wise relevance propagation (LRP) method describes how age-related changes in FCs impact BCI applications for the elderly compared to younger adults. Seventeen younger (24.5±2.7 years) and twelve older (72.5±3.2 years) adults were recruited to perform tasks related to hand-force control with or without mental calculation. CNN yielded a six-class classification accuracy of 75.3% in the elderly, exceeding the 70.7% accuracy for the younger adults. In the elderly, the proposed method increases the classification accuracy by 88.3% compared to the filter-bank common spatial pattern (FBCSP). LRP results revealed that both lower- and higher-order FCs were dominantly overactivated in the prefrontal lobe depending on task type. These findings suggest a promising application of multi-order FC with deep learning on BCI systems for the elderly.

The need for cross-modal retrieval (CMR) among users is growing because of the swift advancements in computer vision and natural language processing. Promoting home operating systems is greatly aided by the openKylin home operating system. It is focused on enhancing the functionality of the operating system with safe and dependable operating technologies. Practical implications abound for integrating computer vision research into home operating systems. A multimodal retrieval approach based on openKylin is presented to improve the usability of text search graphs, audio, and video. The overview of pertinent domestic and international research is the main topic of this article. This technological advancement. It then offers details on the design, implementation procedure, and final implementation outcomes for demonstration. The works of natural operations show that this strategy has excellent accuracy and performance.

We suppose that vacuum is filled with a kind of continuously distributed matter which may be called the $\Omega(1)$ substratum, or the electromagnetic aether. Suppose that the time scale of a macroscopic observer is very large compares to the the Maxwelllian relaxation time of the $\Omega(1)$ substratum. Thus, the macroscopic observer concludes that the $\Omega(1)$ substratum behaves like a Newtonian-fluid. Inspired by H. A. Lorentz, we speculate that electric charges may be extremely small hard spherical sources or spherical sinks with finite radii. Based on the spherical source and spherical sink model of electric charges, we derive Coulomb's law of interactions between static electric charges in vacuum. Further, we derive a reduced form of the Lorentz's force law for static electric charges in vacuum.

Buckling defect will appear on the outer surface of the deformed ring during constrained ring rolling (CRR) of aluminum alloy thin wall conical ring with inner high ribs (AATWCRIHR), if the geometrical dimension of the ribs doesn't match the wall thickness. To avoid the buckling defect, a quantitative method for characterizing the degree of the buckling defect is proposed using the area of buckling profile. Then an orthogonal experimental scheme was designed taking the width of the middle rib, thickness of wall, and height of the middle rib as design variables and defining the area of buckling profile as optimization objective. Subsequently, a quadratic polynomial response surface model was established by combining the optimization algorithm with the finite element method (FEM), and the geometrical dimension of the middle ribs of the deformed AATWCRIHR is optimized. Also the optimal parameter combination to minimize the area of buckling profile is obtained and verified using FE simulation. Results show that the AATWCRIHR after optimization doesn’t generate the buckling defect during constrained ring rolling, and it is proved that the quantitative buckling defect representation method and the optimization design method based on the response surface model and the finite element simulation results are feasible for the constrained ring rolling process of the AATWCRIHR.

Here, satellite images from 2006 to 2022 were collected to assess changes in the sandbar topography of the Nakdong River Estuary region, southeast of South Korea. The employed method of satellite image acquisition involves capturing images at the same time each year to facilitate a comparison of topographical changes over time. The shorelines of the islands in the study area, including Jinwoo Island, Shinja Island, and Doyo Sandbar, were analyzed. Shoreline analysis was performed using the digital shoreline analysis system (DSAS) package in ArcGIS. The results indicate that Jinwoo Island is expanding at 6.46 m/year in the direction of Nulcha Island. The western side of Shinja Island is expanding at 4.76 m/year, whereas the eastern side is retreating at a rate of 24.41 m/year. In the case of the Doyo Sandbar, the southern shoreline is retreating at a rate of 14.69 m/year; however, the speed is gradually decreasing. Marked topographical changes are evident in the Nakdong River Estuary, and the interlinked barrier islands undergo deposition and erosion, leading to alterations in the shoreline. These findings serve as foundational data for predicting and addressing environmental and social issues arising in the Nakdong River Estuary region due to climate change.

Chinese texts often feature a substantial volume of normative content, and their analysis has increasingly become a focal point in recent semantic analysis endeavors. Enhancing the effectiveness of text classification and clustering is pivotal in unveiling the intricate semantics within extensive textual data. Empirical research within the realm of computational social science has underscored the need for improved explanatory power when it comes to general text clustering methods applied to normative texts. This study introduces an innovative hierarchical clustering method that incorporates part-of-speech (POS) features and pioneers a novel semantic network model. It achieves this by amalgamating a POS-based feature weight calculation method with hierarchical clustering techniques. To assess its efficacy, the method is rigorously evaluated across three diverse text datasets, encompassing normative reports, news articles, and social media content. The experimental results unequivocally demonstrate the superior performance of the POS-HC method, surpassing the traditional TF and TF-IDF feature extraction methods in terms of clustering accuracy, and surpassing some existing clustering methods. Furthermore, its classification effectiveness exhibits notable advantages, particularly in the semantic classification of normative texts.

To estimate the progressive collapse resistance capacity of a multi-column frame tube structure with the assembled truss beam composite floor (ATBCF), the pushdown analysis, and the nonlinear dynamic analysis as well, are conducted for such a structure by using the alternate load path (ALP) method. The bearing capacities of the remaining structures at three different work conditions, which are the side middle column failure, the edge middle column failure, and the corner column failure, are individually studied, and the collapse mechanism for the remaining structures is analyzed from the aspects of the internal force redistribution and the failure mode of the second defense line. Simultaneously, the influence of the column failure time on the dynamic response of the remaining structure and the dynamic amplification coefficient are discussed. The results show that the residual bearing capacity of the remaining structure with the bottom corner column failure is higher than that of the one with the side or edge middle column failure, while the latter has a stronger plastic deformation capacity. When the ALP method is adopted to operate the progressive collapse analysis, it is reasonable to take the column failure time as 0.1 times of the first-order vertical vibration period of the remaining structure, and it is suitable to set the dynamic amplification coefficient as of 2.0, which is the ratio of the maximum dynamic displacement to the static displacement of the remaining structure under the transient loading condition.

The robust control of high precision electromechanical systems, such as micropositioners, is challenging in terms of the inherent high nonlinearity, the sensitivity to external interference, and the complexity of accurate identification of the model parameters. To cope with these problems, this work investigates a disturbance observer-based deep reinforcement learning control strategy to realize high robustness and precise tracking performance. Reinforcement learning has shown great potential as optimal control scheme, however, its application in micropositioning systems is still rare. Therefore, embedded with the integral differential compensator (ID), deep deterministic policy gradient (DDPG) is utilized in this work with the ability to not only decrease the state error but also improves the transient response speed. In addition, an adaptive sliding mode disturbance observer (ASMDO) is proposed to further eliminate the collective effect caused by the lumped disturbances. The sterling performance is revealed with intensive tracking simulation experiments and demonstrates the improvement in the accuracy and response time of the controller.