The twisted Wang transform distribution family, defined as the composition of parameter shifted inverse CDF function with an original CDF function, is found to be most suitable for matching low shape factor distributions, characterizing hard to fit or to simulate reinsurance portfolio losses for some perils from our previous study. Among them, the best form for matching a hard-to-fit empirical loss distribution for a specific peril, is the Exponential Fractional Extra Power 0 Distribution in (0,1) with CDF:.The simplest yet still a good form of this family is the Transformed Hyperbolic Tangent Distribution with CDF:,which has analytical formulas for the moments. The twisted Wang transform distribution family is compared and confirmed to be superior to all other well-known distribution families through extensive numerical optimization practice, distribution forms guesses, and computer-aided exploration experiments.

Existing studies often lack a systematic solution for Unmanned Aerial Vehicles (UAV) inspection system, which hinders their widespread application in crack detection. To enhance its practicality, this study proposes a formal and systematic framework for UAV inspection systems, specifically designed for automatic crack detection and pavement distress evaluation. The framework integrates UAV data acquisition, deep learning based crack identification, and road damage assessment in a comprehensive and orderly manner. Firstly, the flight control strategy is presented, and road crack data is collected using the DJI Mini 2 UAV imagery, establishing a high-quality UAV crack image datasets with ground truth information. Secondly, a validation and comparison study is conducted to enhance the automatic crack detection capability and provide an appropriate deployment scheme for UAV inspection systems. This study develops automatic crack detection models based on mainstream deep learning algorithms(namely, Faster-RCNN, YOLOv5s, YOLOv7-tiny, and YOLOv8s) in urban road scenarios. The results demonstrate that the Faster-RCNN algorithm achieves the highest accuracy and is suitable for online data collection of UAV and offline inspection at work stations. Meanwhile, the YOLO models, while slightly lower in accuracy, are the fastest algorithm and are suitable for lightweight deployment of UAV with online collection and real-time inspection. Quantitative measurement methods for road cracks are presented to assess road damage, which will enhance the application of UAV inspection systems and provide factual evidence for maintenance decisions made by road authorities.

Doubly-fed induction generators (DFIG) find extensive application in variable-speed wind power plants, providing notable advantages such as cost-effectiveness, operational flexibility across varying speeds, and enhanced power quality. This research focuses on the control of DFIGs employed in variable-speed wind turbine configurations. A suitable mathematical model is chosen for representative systems following a comprehensive review of contemporary research. Subsequent analysis reveals the instability of the open-loop time response of the system. To address this instability, the initial approach involves the implementation of the conventional Model Predictive Controller (MPC). However, the outcomes indicate that this controller falls short of delivering satisfactory performance despite the enhanced stability. In the subsequent phase, efforts are made to mitigate the impact of wind input variability by utilizing the Kalman filter, given its effectiveness in handling high variability. Following this, a novel methodology is introduced, which combines nonlinear MPC with the Lyapunov function. This method is based on the nonlinear model of the system. By using the Lyapunov function in the nonlinear MPC structure, the stability of the designed controller is guaranteed. The simulation results conducted using MATLAB software show that the output variables of the modeled DFIG system achieve stability within a reasonable timeframe applying the input.

Road cracks significantly affect the serviceability and safety of roadways, especially in mountainous terrain. Traditional inspection methods, such as manual detection, are excessively time-consuming, labor-intensive, and inefficient. Additionally, multi-function detection vehicles equipped with various sensors are expensive and not suitable for mountainous roads due to poor conditions. To address these challenges, this study proposes a customized Unmanned Aerial Vehicles (UAV) inspection system designed for automatic crack detection. The system focuses on enhancing autonomous capabilities in mountainous terrains by incorporating embedded algorithms for route planning, autonomous navigation, and automatic crack detection. The slide window method is proposed to enhance the autonomous navigation of UAV flights by generating path planning in mountainous roads. This method compensates for GPS/IMU positioning errors, particularly in GPS-denied or GPS-drift scenarios. Moreover, the YOLOv8 algorithm is introduced to conduct autonomous crack detection from UAV imagery in the offboard module. To validate our UAV inspection system's performance, we conducted several experiments to assess its accuracy, robustness, and efficiency. The experimental results demonstrate that our UAS inspection system accurately estimates the flight trajectory along the mountainous road for autonomous navigation. Furthermore, the experimental detection results also demonstrate that the YOLOv8 algorithm achieves higher recognition accuracy compared to the YOLOv5, and YOLOv7-tiny algorithms, exceeding 3.1%,and 6.8% of mAP, respectively. In summary, the UAV inspection system proposed in this study can provide a useful tool and technological guidance for the regular inspection of mountainous roads.

Polyvinyl alcohol-engineering cementitious composites (PVA-ECC) has been widely applied in bridge deck repairing or widening, the common practice for doing this is that a portion of a bridge is left open to traffic while the closed portion is constructed, which expose the early age PVA-ECC to the vehicle-induced vibrations. However, whether vehicle-induced vibrations affect the tensile performance of early age PVA-ECC remains unknow. The purpose of this study was to conduct laboratory test programs on how much vehicle-induced vibrations during early ages affected the tensile performance of PVA-ECC. A self-improved device was used to simulate the vehicle-induced vibrations, and after vibrating with the designed variables, both a uniaxial tensile test and a grey correlation analysis were performed. The results indicated that: the effects of vehicle-induced vibrations on the tensile performance of early age PVA-ECC were significant, and they generally tended to be negative in this investigation. In particular, for all of the vibrated PVA-ECC specimens, the most negative age when vibrated occurred during the period between the initial set and the final set. We concluded that although vehicle-induced vibrations during the setting periods had no substantial effects on the inherent strain-hardening characteristics of PVA-ECC, the effects should not be ignored.

The decreasing width, increasing aspect ratio RDL presents significant challenges to design for reliability (DFR) of advanced package. Therefore, this paper proposes a ML based RDL modeling and simulation method. In the method, RDL is divided into blocks and subdivided into pixels of metal percentage, and the RDL is digitalized as tensors. Then, an ANN-based surrogate model is built and trained by a subset of tensors to predict the equivalent material properties of each block. Lastly, all blocks are transformed into elements for simulations. For validation, line bending simulations were conducted on an RDL, with the reaction force as accuracy indicator. The results show that neglecting layout impact causes critical errors as substrate thins. By the method, the reaction force error is 2.81% and the layout impact can accurately be considered with 200×200 elements. For application, the TCT maximum temperature state simulation was conducted on a CPU chip. The simulation indicates that for advanced package the maximum stress more likely occurs in RDL rather than bumps, both RDL and bumps are critical impacted by layouts, and RDL stress is also impacted by vias/bumps. The proposed method precisely concerns layout impacts with little resources, presents an opportunity of efficiency improvement.

To describe the hysteresis nonlinearities in smart actuators, numerous models have been presented in the literature, among which the Preisach operator would be the most effective one due to its capability in capturing multi-loop or sophisticated hysteresis curves. When such an operator is coupled with uncertain nonlinear dynamics, especially in noncanonical form, it is a challenging problem to develop techniques to cancel out the hysteresis effects, and at the same time achieve asymptotic tracking performance. To resolve this problem, in this paper, we investigate the problem of iterative inverse-based adaptive control for an uncertain noncanonical nonlinear systems with unknown input Preiasch hysteresis, and a new adaptive version of the closest match algorithm is proposed to compensate for the Preisach hysteresis. With our scheme, the stability and convergence of the closed-loop system can be established. The effectiveness of the proposed control scheme is illustrated by simulation and experiment results.

In order to reduce the risk of grid transient voltage instability brought about by the new energy and system dynamic loads and the increasing proportion of new energy access, this paper proposes a differentiated dynamic reactive power compensation configuration method for suppressing transient voltage dip instability. The method first establishes a dynamic reactive power device configuration index system based on a multi-binary table, and then establishes a differentiated dynamic reactive power compensation device configuration model based on the node instability risk characteristics by combining with the regional division of system transient voltage instability risk. The model takes the investment cost and suppression effect as the optimization objectives, and realizes differentiated dynamic reactive power compensation by flexibly adjusting the optimization weights of economic benefits and reactive power compensation effects in the configuration process; Compared with the traditional compensation methods, differentiated compensation can significantly improve the economic benefits of reactive power compensation configuration. Finally, taking the IEEE39 node test system as an example, the improved TLBO algorithm is used to solve the model, which verifies the accuracy and effectiveness of the method proposed in this paper.

Purpose: The purpose of this study is to further explore how e-loyalty and E-marketing influences E-trust and satisfy the demand by offering fresh perspectives based on research as well as emphasis on the factors influencing the E-trust such as culture as a mediator. This study not only contributed theoretically but also presented practical implementations. Design/methodology/approach: Online survey was used to obtain data by focusing the Hospitality sector (Hotel Industry) and verifying the conceptual framework. Data was collected in multiple time lags. Findings: Findings showed that the E-trust influenced by E-loyalty and E-Marketing. E-trust comes from the previous experiences, e-loyalty and e-marketing. Further, some trends such as culture influenced the e-trust. Research limitation/implications: The present study is quite suitable for those Researchers interested in learning more about the effects of E-loyalty and E-marketing on user E-trust and how to mitigate cultural influences can benefit from the current study. This research also has implications for those who wish to improve market allure and survival in digital world. This study focused on the hospitality sector (Hotel Industry) in China; however, the sector and geography could be altered to suit the needs of the study's participants. Practical implications: The present study delivers the practical guidelines which are quiet suitable for understanding the formation of E-loyalty, E-marketing, and E-trust through which specific E-marketing strategy can be designed to deal with the consumer’s E-loyalty and their expectations as per their Cultural perspective. At some particular regions/countries, cultural trends are more important than practical market. This research study practically showed that how culture changed the consumer set of mind. Originality/value: The relationship between E-loyalty, E-marketing, E-trust, specifically with the cultural influence in digital market has been the subject of few research.

(1) Background: AI technology has been deeply applied to online shopping platform to provide more accurate and personalized services for consumers. It is of great significance to study the different functional experience of AI for consumers to improve the current application status of AI technology.(2)Method: Based on the "S-O-R" model, this study divided the AI technology expe-rienced by the consumers of online shopping platform into accuracy, insight and interaction experience. Takes the perceived value as the mediating variable from the prospect of perceived utility value and perceived hedonic value. This article use empirical research method to analyze the effect of three dimensions of online shopping AI experience to research the internal influence mechanism of consumers purchase intention. (3) Results:① The accuracy, insight and interaction experience of AI marketing technology have a significant positive impact on consumers' per-ceived utility value and hedonic value respectively; ②Both of the perceived utility value and perceived hedonic value obtained by AI technology experience can promote the formation of consumers' purchase intention; ③ The perceived hedonic value was better than perceived utility value to promote the consumers' purchase intention; ④The results of multi group analysis show that some younger and less experiences consumers groups prefer the pleasure experience such as shopping desire stimulation, shopping process relaxation and pleasure that AI marketing brought. However, utilitarian value cannot promote this kind of consumers' purchase intention. (4) Con-clusions: Perceived utility value and perceived hedonic value can be the intermediary between AI technology and consumers' purchase intention.

Recent researches indicated that metal nanoparticles which have the unique optical properties can be used to enhance the spectral response of the photovoltaic modules. Since most of the nanoparticles have enhancement effects in a specific wavelength range, improving the spectral response of the photovoltaic modules in a broadband range is crucial for their applications in imaging, energy harvesting, and optical communication. In this study, flower-like silver particles are applied to achieve the enhancement effects in a broadband range. The optical absorption of photovoltaic modules is improved in a broad wavelength range of 400~2000 nm by immobilizing flower-like silver particles onto an amorphous Si p-i-n structure, and the peak responsivity of the spectral response is enhanced by about 10 times. Theoretical investigation further elaborates that the enhancement originates from the near-field effects of silver particles due to the interaction of different parts of the flower-like silver particles. Through these studies, we demonstrate that, utilizing the subwavelength silver particles with roughness surface can achieve the spectral response of the photovoltaic modules enhanced in broadband range, which can improve the utilization efficiency of optical energy for the applications of sensing, imaging, optical communication, and energy harvesting.

The COVID-19 pandemic has now become very severe as never before due to the overwhelming spread of Omicron. We found that Omicron outbreak can be effectively prevented by inactivated vaccines, which averted an outbreak of more than 1.6 million people in Hangzhou, China. The 36 mutations in the target spike protein of Omicron neutralizing antibody enable it to evade the immune protection afforded by vaccines. This is because that mRNA and adenovirus-vector vaccines are designed to recognize the spike (S) glycoprotein of the SARS-CoV-2 wild-type (WT) strain. However, Inactivated vaccines contain the whole viral antigens and remain stable in their recognition of newly emerging variants of SARS-CoV-2. Our study confirmed the advantage of inactivated vaccines in the face of highly mutated Omicron variant and provided a basis for the development of effective vaccines to prevent future long-term transmission, mutation and recurrence of SARS-CoV-2.

Introduction: Spinal epidural arteriovenous fistulas (SEDAVFs) are extremely rare and the pathological process still remains unclear. Nevertheless, neurofibromatosis, surgery, as well as trauma have been implicated as causes. Nevertheless, long standing chronic vertebral compression fractures (VCFs) as a cause of SEDAVFs has not been reported in literature. Case Presentation: Our cases comprised of a male and female with ages 67 and 62 year respectively. They presented with weakness of bilateral lower extremities and back pain. Their symptoms deteriorated into mild recto-bladder dysfunction as well as hypoesthesia of lower limbs. They both had history of road traffic accidents (RTAs) prior to their symptomatology. In both cases, Magnetic resonance imaging (MRI) revealed VCFs prior to the above symptomatology. Spinal digital subtraction angiography (DSA) was used to confirm SEDAVFs in both cases. We utilized the trans-arterial route with Onyx embolization agent to obliterate both fistulae and their symptom resolved after the embolization. Two-years follow-ups revealed no recurrence of their fistulae. Conclusion: The initial long standing VCFs caused by trauma resulted in perforation of the dorsal somatic branches of the radicular artery leading to the occurrences of SEDAVFs in our cases.

Archie model is the basis of calculating oil saturation, but there are some limitations when using this model to calculate oil saturation in water-flooded layer. The main reason is that the main parameters, such as rock resistivity and formation water resistivity, are constantly changing dynamic parameters in the underground with the influence of injected water. Considering that water-flooded layers changes with injection waters, influence factors of rock resistivity and formation water resistivity of primary parameters are analyzed. Considering the dynamic data of water cut is the most reactive underground fluid characteristics of real information, combined with dynamic and static, and the “double ratio” model of later development by the same sedimentary layer is established, which realizes the inversion of rock resistivity and formation water resistivity, then modified Archie model relating to water-flooded layers of the same sedimentary explaining formation. The explanation of actual data indicates that the “double ratio” model well considers the dynamic variation of production data, which makes the inversion of the flooded rock resistivity relatively accurate, besides, the modified Archie model can accurately calculate the oil saturation of water-flooded layers with a reasonable result, which offers scientific basis for the predicting of remaining oil distribution rules.

Objective: To visualize and analyze the published literature on diabetes and pyroptosis based on a bibliometric approach, so as to provide a comprehensive picture of the hot research directions and dynamic progress in this field. Methods: This study was based on the web of science core collection database to conduct a comprehensive search of the published literature in the field of diabetes and Pyroptosis from January 1985 to August 2022, including the published research literature in this field, as well as a visual analysis of the number of citations, year of publication, journal, author, research institution, country, and research topic. Results: A total of 139 literature on research related to diabetes and cellular scorch from 2011 to 2022 were retrieved, with a total of 3009 citations and a maximum of 255 citations for a single article, which had a first authorSchmid-Burgk, JL The first author of this article is from Germany; among 20 publishing countries, China leads with 100 articles; among 222 publishing institutions, Harbin Medical University leads with 18 articles and 184 citations; among 980 authors, Chen, X from China tops the list of high-impact authors with 5 articles and 29 citations; Among the 98 journals, "CELL DEATH DISEASE" ranked first in both volume and high impact journals with 4 articles and 29 citations; among 349 keywords, "pyroptosis" ranked first with a cumulative frequency of 65 times. The cluster analysis was divided into three categories, chronic complications of diabetes and pyroptosis (67 articles), diabetes and pyroptosis (60 articles), and diabetes combined with other diseases and pyroptosis (12 articles), and the number of articles related to diabetes and its chronic complications increased rapidly from 2019, among which, diabetic cardiomyopathy (27 articles) had the highest number of articles. Conclusions: Based on a comprehensive analysis of published literature in the field of diabetes and pyroptosis from 2011-2022, this study achieved a visual analysis of studies with significant and outstanding contributions to the field, thus framing a picture showing the development and changes in the field. At the same time, this study provides research information and direction for clinicians and investigators to conduct diabetes and pyroptosis related research in the future.

The circadian clock regulates daily changes in behavioral, endocrine and metabolic activities in mammals. Circadian rhythms in cellular physiology are significantly affected by aging. In particular, we previously found that aging has profound impact on daily rhythms in mitochondrial functions, leading to increased oxidative stress. However, this is unlikely due to malfunction of molecular clocks in the suprachiasmatic nucleus or peripheral tissues, as robust clock oscillations are observed therein in old animals. Nonetheless, aging induces changes in gene expression levels and rhythms in various peripheral and probably central tissues. In this article, we review findings on the roles of the circadian clock and aging in regulating mitochondrial rhythms and redox homeostasis. Chronic sterile inflammation is implicated in mitochondrial dysfunction and increased oxidative stress during aging. In particular, upregulation of CD38 by inflammatory response can disturb mitochondrial functions in multiple ways.

Multidisciplinary Design Optimization (MDO) is the most active field in the design of current complex system engineering, which is possessed with such two difficulties as subsystem information exchange and analytical and computational complexity of systems. Therefore, an improved collaborative optimization algorithm based on ANN (artificial neural network) response surface was proposed dependent on the consistency constraint algorithm and concurrent subspace algorithm. As an optimization method with secondary structure, it satisfied only local constraints in discipline layer, but provided a coordinated mechanism for interdisciplinary conflict in system layer. Finally, it was applied in the multidisciplinary design optimization of autonomous underwater vehicle (AUV). As shown from the result, the MDO convergence stability and reliability of low resistance, low noise and high maneuvering performance of the AUV shape can be ensured by the improved collaborative optimization algorithm, thus verifying the effectiveness of the algorithm.

This study investigated the mechanical properties and fatigue behavior of FH36 steel plate rolled in different directions. By adopting a sequential rolling process in the rolling direction (RD) and transverse direction (TD), the differences in properties between RD and TD were eliminated, resulting in nearly identical tensile properties. The steel plate exhibited a yield strength of approximately 420 MPa, a tensile strength of approximately 506 MPa, and an elongation of approximately 25%. Fatigue tests conducted at room temperature and -60℃ showed a fatigue limit of the maximum stress of 488 MPa at room temperature and 500 MPa at -60℃, indicating improved low-temperature fatigue performance. The fracture surfaces displayed distinct characteristics, such as oblique shearing fractures for high-cycle fatigue and cup-cone shape fractures for low-cycle fatigue. The fatigue source zone were both on the surface of the specimens. As the maximum stress increased, the area of the crack propagation zone for high-cycle fatigue decreased, while the area of the final fracture zone, the number of dimples and the proportion of the LAGBs increased.

Cell autonomous circadian oscillation is present in central and various peripheral tissues. The intrinsic tissue clock and various extrinsic cues drive gene expression rhythms. Transcription regulation is thought to be the main driving force for gene rhythms. However, how transcription rhythms arise remains to be fully characterized, due to the fact that transcription is regulated at multiple steps. In particular, Pol II recruitment and pause release are two critical regulatory steps that determine the status of Pol II pausing. Recently, we showed that Pol II pausing exhibits genomewide changes during daily transcription in mouse liver. In this article, we review historical as well as recent findings on the regulation of transcription rhythms. We also discuss the possible mechanisms for daily changes in Pol II pausing and the critical involvement of Pol II pausing regulation in generating rhythmic transcription output.

An inverse aeroacoustic problem for a helicopter rotor combined with aerodynamic constraint is proposed based on Ffowcs Williams and Hawkings equation in subsonic. The rotor noise includes thickness noise and loading noise when quadrupole noise is neglected. Thickness noise is related to geometry and motion conditions. Loading noise is related to the pressure on the wall. Therefore, the equation between pressure on the wall and far-field noise can be established, thus the pressure on the wall can be obtained by solving this equation. Since this equation is an ill-posed, the singular value decomposition combined with the regulation method is applied and the aerodynamic constraint is taken into account. The direct noise prediction is verify firstly and then the inverse problem is solved. The reconstruction pressure is compared to the input data. The result is in good agreement with the input value. At the same time, the influence of interference noise is also considered. Under low signal-to-noise ratio, the reconstruction result is also reasonable.

Cadmium (Cd) contamination in rice grains is posing a significant threat to global food security. To restrict the transport of Cd in the soil-rice system, an efficient way is to use the ionomics strate-gy. Since calcium (Ca) and Cd have similar ionic radii, their uptake and translocation may be linked in multiple aspects in rice. However, the underlying antagonistic mechanisms are still not fully understood. Therefore, we first summarized the current knowledge on the physiological and molecular footprints of Cd translocation in plants and then explored the potential antagonistic points between Ca and Cd in rice, including exchange adsorption on roots, plant cell wall compo-sition, co-transporter gene expression, and transpiration inhibition. This review provides sugges-tions for the Ca/Cd interacting study in rice and introduces the ionomics research to better control the accumulation of Cd in plants.

Vegetation has a significant influence on velocity distribution and turbulent energy in a confluence channel. A laboratory measurement with ADV was used to investigate the flow through a Y-shaped confluence channel partially covered with rigid vegetation on its inner bank. In this study, the flow velocities in cases with and without vegetation were measured by the ADV in a Y-shaped confluence channel. The results clearly show that the existence of non-submerged rigid plants has changed the internal flow structure, that the velocity in the non-vegetated area is greater than in the vegetated area, and that there is a large exchange of mass and momentum between the vegetated and non-vegetated areas. The velocity on both sides is significantly reduced when vegetation is present. In the vicinity of tributaries, due to the presence of vegetation, the high-velocity area moved rapidly to the middle of the non-vegetated area, and the secondary flow phenomenon disappeared. In the mainstream, when vegetation was present, circulation disappeared, and the degree of lateral mixing decreased. The presence of vegetation caused a great change in the internal flow structure and made the flow in non-vegetated areas more intense.

(1) Background: After the discovery and application of Chlamydomonas reinhardtii channelrhodopsins, the optogenetic toolbox has been greatly expanded with engineered and newly discovered natural channelrhodopsins. However, channelrhodopsins of higher Ca2+ conductance or more specific ion permeability are still in demand. (2) Methods: In this study, we mutated the conserved aspartate of the transmembrane helix 4 (TM4) within Chronos (Stigeoclonium helveticum channelrhodopsin = ShChR) and PsChR (Platymonas subcordiformis channelrhodopsin) and compared them with published ChR2 (C. reinhardtii channelrhodopsin-2) aspartate mutants. (3) Results: We found that the ChR2 D156H mutant (XXM) showed enhanced Na+ and Ca2+ conductance, which was not noticed before, while the D156C mutation (XXL) influenced the Na+ and Ca2+ conductance only slightly. Furthermore, the D173H mutant of PsChR showed a much improved photocurrent, compared to wildtype, and even higher Na+ selectivity to H+ than XXM. PsChR D173H also showed a strongly enhanced Ca2+ conductance, more than 2-fold that of the calcium translocating L132C of ChR2 (CatCh). (4) Conclusions: We found that mutating the aspartate of the TM4 to histidine influences the ion selectivity of channelrhodopsins. With the large photocurrent and enhanced Na+ selectivity and Ca2+ conductance, XXM and PsChR D139H are promising powerful optogenetic tools, especially for Ca2+ manipulation.

Obesity results in hepatic fat accumulation, i.e., steatosis. Besides the fat overload, impaired fatty acid β-oxidation also promotes steatosis. Fatty acid β-oxidation takes place in mitochondria and peroxisomes. Usually very long chain and branched-chain fatty acids are first oxidized in peroxisomes, and the resultant short chain fatty acids are further oxidized in mitochondria. Peroxisome biogenesis is regulated by peroxin 16 (PEX16). In liver-specific PEX16 knockout (Pex16Alb-Cre) mice, hepatocyte peroxisomes were absent, but hepatocytes proliferated, and liver mass was enlarged. These results suggest that normal liver peroxisomes restrain hepatocyte proliferation and liver sizes. After high fat diet (HFD) feeding, body weights were increased in PEX16 floxed (Pex16fl/fl) mice and adipose-specific PEX16 knockout (Pex16AdipoQ-Cre) mice but not in the Pex16Alb-Cre mice, suggesting that the development of obesity is regulated by liver PEX16 but not by adipose PEX16. However, it was previously reported that HFD-induced obesity in the Pex16AdipoQ-Cre mice was more severe than in the wild type mice, which was not observed until 27 weeks of HFD feeding. Thus, liver initiates the development of obesity, which is enhanced by abnormal adipocytes. HFD increased liver mass in the Pex16fl/fl mice but somehow reduced the already enlarged liver mass in the Pex16Alb-Cre mice. Basal levels of serum triglyceride, free fatty acids and cholesterol were decreased whereas serum bile acids were increased in the Pex16Alb-Cre mice, and HFD-induced steatosis was not observed in the Pex16Alb-Cre mice. These results suggest that normal liver peroxisomes contribute to the development of liver steatosis and obesity.

Microscopic vision plays an important role in automated micro-assembly. However, some uncertain factors in the assembly process, such as occlusion and stains can lead to the mistakes of feature extraction. Herein, to solve the problem, the deep learning techniques are introduced into the feature recognition tasks, focusing on the attention mechanism and visualizing CNNs for DL-based microscopic vision. The main contributions are summarized as follows: The CBAM attention mechanism is combined with the YOLOv5 algorithm to improve the accuracy and robustness of feature extraction. The micropart feature occlusion experiment results show that at 70% occlusion degree, YOLOV5-CBAM can reach 97.9% [email protected], which is 4.6% higher than the original one. Visualization analysis of DL-based model is conducted using Grad-CAM to make the decision result more transparent and avoid potential visual detection risks during assembly. The heatmap matching degree between GT area and high-light area is increased by 27.81% on average, which further verify the effectiveness of attention mechanism in micropart feature localization. Additionally, micropart surface stain and droplet quality classification models based on ResNet50 are trained to replace the manual sorting. The visual results are consistent with human eye discernment and judgement, confirming the reliability of parts and droplets sorting.

In this paper, the methods and their analysis for estimating the location of three dimension (3-D) single source buried in lossy medium are presented with uniform circular array (UCA). The mathematical model of the signal in the lossy medium is proposed. Using location information in the covariance matrix obtained by sensors’ output, the equations of the source location (azimuth angle, elevation angle and range) are obtained. The phase and amplitude of the covariance matrix function are used to process these equations respectively. Then, the phase and amplitude of the covariance matrix function are used to process the source localization in the conductive medium together. By analyzing the characteristics of the proposed methods and MUSIC method, the computational complexity and the valid range of these methods are given. From the results, whether the loss is known, we can choose the appropriate method to process the issues (localization in lossless medium or lossy medium).

Wearable touch sensors, which can convert force or pressure signals into quantitative electronic signals, have emerged as an essential smart sensing devices and played an important role in various cutting-edge fields, including wearable health monitoring, soft robots, electronic skin, artificial prosthetics, AR/VR, and the Internet of Things. Flexible touch sensors have made significant advancements, while construction of novel touch sensors via mimicking the unique properties of biological materials and biogenetic structures always remains a hot research topic and significant technological pathway. This review provides a comprehensive summary of the research status of wearable touch sensors constructed by imitating the material and structural characteristics in nature, and also summarizes the scientific challenges and development tendency of this aspect. Firstly, the research status for constructing flexible touch sensors based on biomimetic materials is summarized, including hydrogel materials, self-healing materials, and other bioinspired or biomimetic materials with extraordinary properties. Then, design and fabrication of flexible touch sensors based on bionic structures for performance enhancement are fully discussed. These bionic structures include special structures in plants, special structures insects/animal, and special structures in human body. Moreover, a summary of the current issues and future prospects for developing wearable sensors based on bioinspired materials and structures is discussed.

Due to the non-degradability of petroleum-based packaging materials, serious environmental pollution and the depletion of non-renewable resources have become pressing issues. In order to actively promote green production and address these concerns, there is an urgent need for new packaging materials to replace traditional plastic products. Starch-based packaging materials, composed of starch, fiber, and plasticizers, offer a degradable and environmentally friendly alternative. Starch alone cannot undergo thermoplastic processing due to its inherent structural characteristics. Therefore, researchers have explored modifications by incorporating plasticizers to create processable thermoplastic starch (TPS). However, there are challenges related to the high crystallinity and poor compatibility between TPS and fibers, resulting in decreased mechanical properties. To address these challenges, a novel approach combining plasticizer optimization and response surface method (RSM) optimization has been proposed to enhance the mechanical properties of starch-based packaging materials. This method leverages the advantages of composite plasticizers and process parameters. The findings demonstrate that the composite plasticizer effectively disrupt the hydrogen bonding and granule morphology of starch, leading to a significant reduction in crystallinity. Based on these findings, the optimal process parameters are determined using the RSM, resulting in a forming temperature of 198 °C, forming time of 5.4 minutes, and AC content of 0.84 grams. Compared with the non-optimized values, the tensile strength increases by 12.2% and the rebound rate increases by 8.1%.

The Pingbei area is the main accumulation area of oil and gas in the Xihu Sag. The phase characteristics of oil and gas in this area are complex, and the understanding of their genesis is still unclear. In this paper, based upon discussions of crude oil and natural gas geochemical data, integrated with local geological features, we discuss the sources, migration, and phase state characteristics of oil and gas in the Pingbei area of the Xihu Sag. The study results showed that the crude oil and natural gas in the Pingbei area are coal-derived and the oil and gas produced by the humic organic matter during the maturity stage. The oil and gas source correlation showed that crude oil and natural gas have good affinity with the Eocene Pinghu Formation (PF) coal-bearing source rocks. Crude oil has the characteristics of near-source accumulation and short-distance migration while natural gas is supplied from a dual source: the coal-derived hydrocarbon rocks of PH in the deep part of the study area, supplemented by the coal-derived hydrocarbon rocks of PH on the bottom of the slope, and adjacent hydrocarbon-bearing sub sag. The distribution characteristics and geochemical migration indices of hydrocarbon showed that the oil generated from the hydrocarbon source rocks of PH in the deep Pingbei area mainly migrates vertically along the fault connecting the reservoir and the source rocks to the trap, where it accumulates, while the natural gas exhibits deep and large faults that mainly migrate vertically, supplemented by its lateral migration along the composite transport system composed of faults and sandstone layers in the slope zone. The mechanisms of produced, exhausted, and geochromatographic effects (PGE), as well as evaporative fractionation (EF) and phase-controlled migration fractionation (PMF), result in the obvious discrepancy of hydrocarbon’s properties on the vertical profiles.

Intelligent systems are increasingly present in various areas of society, gaining special relevance in healthcare environments. In this work, grounded on previous developments proposed by the authors, the evolution and improvement of a novel intelligent system focused on the diagnosis of obstructive sleep apnea (OSA) is addressed. To do this, starting from two packages of information of a heterogeneous nature, and deploying a set of Machine Learning classification algorithms, focused each of them on different levels of the apnea-hypopnea index (AHI), as well as a set of cascaded expert systems, it is possible to obtain a series of risk metric pairs (Statistical Risk, Symbolic Risk) for each AHI level, understood as a warning forecast associated with the early detection of the pathology. The risk indicators of each pair are subsequently aggregated by means of a symbolic inference system, whose knowledge base was determined using the automatic rule generation approach proposed by Wang and Mendel. At the output of each inference system, a risk indicator is obtained for each AHI level, the Apnea Risk, whose interpretation makes it possible to discriminate between patients who could suffer OSA and those who do not, as well as to generate the appropriate recommendations. For the initial tests of the system, the design and development of a specific software artifact was carried out using data from 4,400 patients from the Álvaro Cunqueiro Hospital in Vigo, obtaining when applied to the test set AUC values within the range 0.74–0.88, which invites optimism and points to the benefits expected from the architecture of the proposed intelligent system.

Plants of the genus Monochoria have long been utilized in food, cosmetics, and traditional herbal treatment. Thailand has the highest species diversity of this genus and a new member, Monochoria angustifolia (G. X. Wang) Boonkerd & Tungmunnithum has been recently described. This plant is called “Siam Violet Pearl” as a common name or “ไข่มุกสีม่วงแห่งสยาม” as its vernacular name in the same meaning in Thai language. Despite their importance, few researches on Monochoria species have been conducted. This study, thus, provided the results to fill in this gap by: i) determining flavonoids phytochemical profiles of 25 natural populations of M. angustifolia covering the whole floristic regions in Thailand, and ii) determining antioxidant activity using various antioxidant assays to investigate the probable mechanism. The results revealed that M. angustifolia presented a higher flavonoid content than the outgroup, M. hastata. Our results also revealed that flavonoids might be used to investigate Monochoria evolutionary connections and for botanical authentication. The various antioxidant assays revealed that M. angustifolia extracts preferentially act through a hydrogen atom transfer antioxidant mechanism. Pearson correlation analysis indicated significant correlations emphasizing that the antioxidant capacity is most probably the result of a complex phytochemical combinations rather than of a single molecule. Altogether, these results showed that this new species provide an attractive alternative starting material with phytochemical variety and antioxidant potential for the phytopharmaceutical industry.

In this work, we designed a MEMS device which allows simultaneous direct measurement of mechanical properties during deformation under external stress and characterization of the evolution of microstructure of nanomaterials within a transmission electron microscope. This MEMS device makes it easy to establish the correlation between microstructure and mechanical properties of nanomaterials. The device uses piezoresistive sensors to qualitatively measure the force and displacement of nanomaterials, e.g., in wire and thin plate forms. The device has a theoretical displacement resolution of 0.19 nm and a force resolution of 2.1 μN. The device has a theoretical displacement range limit of 2.74 μm and a load range limit of 27.75 mN.

The study of trophic relationships among closely related species plays an important role in deepening our understanding of the resource utilization characteristics, differentiation patterns, and population dynamics of co-occurring species in the same habitat. This research uses two congeneric fish species, Pennahia pawak and Pennahia anea, as examples. Based on stomach content analysis and carbon-nitrogen stable isotope analysis, a comparative analysis of their feeding habits and trophic niches is conducted. Additionally, spatial niche analysis is employed to explore the coexistence and competitive mechanisms between these two closely related fish species. The results showed that both P. pawak and P. anea had similar feeding habits, mainly feeding on Pisces and Macrura, but there were some feeding preferences between the two species. Interspecific prey overlap was meaningful but not significant, with an overlap coefficient of 0.56. There were significant differences in feeding habits between the two species during different seasons. Based on stable isotope analyses, body length of both species had a significant positive correlation with δ15N (Pearson r=0.65, P<0.01; Pearson r=0.44, P<0.01), but not with δ13C (P>0.05). Standard ellipse corrected area (SEAc) of P. pawak and P. anea were 0.65 and 1.16, while the trophic niche overlap was only 0.29, which was not significant; the spatial niche width of the two was 1.19 and 0.58, respectively, and the spatial niche overlap was only 0.20, which was not significant. Intra-species competition was intense in P. pawak and P. anea, but reduced feeding specialization had a mitigating effect on intra-species competition. Interspecific competition was present but not significant, and was mitigated by trophic and spatial niche differentiation.

Due to the global warming and dynamic changes in pathogenic virulence, leaf rust caused by Puccinia triticina has greatly expanded its epidermic region and become a severe threat to global wheat production. Genetic bases of wheat resistance to leaf rust mainly relies on the leaf rust resistance (Lr) gene or quantitative trait locus (QLr). Although these genetic loci have been insensitively studied during the last two decades, an updated overview of Lr/QLr in a genome-wide level is urgently needed. This review summarized recent progresses in genetic studies of wheat resistance to leaf rust. Wheat germplasms with great potentials in genetic improvement of resistance to leaf rust were highlighted. Key information about the genetic loci carrying Lr/QLr were summarized. A genome-wide chromosome distribution map for all the Lr/QLr was generated based on the released wheat reference genome. In conclusion, this review has provided valuable sources for both wheat breeders and researchers to understand the genetics of resistance to leaf rust in wheat.

Although the concept of additive manufacturing has been proposed for several decades, momentum of selective laser melting (SLM) is finally starting to build. In SLM, density and surface roughness, as the important quality indexes of SLMed parts, are dependent on the processing parameters. However, there are few studies on their collaborative optimization in SLM to obtain high relative density and low surface roughness simultaneously in the previous literature. In this work, the response surface method was adopted to study the influences of different processing parameters (laser power, scanning speed and hatch space) on density and surface roughness of 316L stainless steel parts fabricated by SLM. The statistical relationship model between processing parameters and manufacturing quality is established. A multi-objective collaborative optimization strategy considering both density and surface roughness is proposed. The experimental results show that the main effects of processing parameters on the density and surface roughness are similar. It is noted that the effects of the laser power and scanning speed on the above objective quality show highly significant, while hatch space behaves an insignificant impact. Based on the above optimization, 316L stainless steel parts with excellent surface roughness and relative density can be obtained by SLM with optimized processing parameters.

In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

Multimodal remote sensing data classification can enhance the model’s ability to distinguish land features through multimodal data fusion. In this context, how to help models understand the relationship between multimodal data and target tasks is the focus of researchers. Inspired by human feedback learning mechanisms, causal reasoning mechanisms, and knowledge induction mechanisms, this paper integrates causal learning, reinforcement learning, and meta learning into a unified remote sensing data classification framework and proposed the causal meta-reinforcement learning (CMRL). First, based on feedback learning mechanisms, we have overcome the limitations of traditional implicit optimization of fusion features and customized a reinforcement learning environment for multimodal remote sensing data classification tasks. Through feedback interactive learning between agents and the environment, we help them understand the complex relationships between multimodal data and labels, thereby achieving full mining of multimodal complementary information. Second, based on the causal inference mechanism we designed causal distribution prediction action, classification reward, and causal intervention reward, capturing pure causal factors in multimodal data and cutting off false statistical associations between non-causal factors and class labels. Finally, based on the knowledge induction mechanism, we designed a bi-layer optimization mechanism based on meta-learning. By constructing a meta training task and meta validation task simulation model in the generalization scenario of unseen data, we helped the model induce cross-task shared knowledge, thereby improving its generalization ability for unseen multimodal data. The experimental results on multiple sets of multimodal datasets show that the proposed method achieved state-of-the-art performance in multimodal remote sensing data classification tasks.

The motor protein Prestin found in the outer hair cells (OHCs) of the inner ear is responsible for producing high sensitivity and sharp frequency selectivity for mammalian hearing. Some studies have suggested that Prestin could serve as a serological biomarker for cochlear damage since OHCs are highly vulnerable to damage from various sources of insults. However, the reported data are inconsistent and lack appropriate negative controls. To investigate this further, we measured Prestin quantities in the bloodstream using ELISA kits from different companies. Wildtype (WT) mice were exposed to different ototoxic treatments, including noise exposure and ototoxic reagents that kill OHCs rapidly. Prestin-knockout (KO) mice were used as a negative control. Our data show that some ELISA kits were not able to detect Prestin specifically. The ELISA kit that could detect Prestin protein from cochlear homogenates failed to detect Prestin in the bloodstream despite significant damage to OHCs in cochleae. Furthermore, the optical densities of samples, which correlate to Prestin quantities, were significantly influenced by hemolysis in the samples. In conclusion, Prestin from OHCs is not a sensitive and reliable serological biomarker for detecting cochlear damage in mice.

Meat serves as a vital component of the human diet, offering a rich source of protein and essential trace elements. China stands as both a significant producer and consumer of meat on a global scale, leading the world in terms of total meat production and consumption. As the standard of living within the country continues to rise, there is a growing emphasis on the nutritional value and safety of meat consumption. The tenderness of meat is a critical factor influencing its overall quality. Traditionally, tenderness has been assessed through shear force testing, a method that is inherently destructive, inefficient, and results in considerable sample wastage. In light of these drawbacks, non-destructive testing techniques have emerged as a preferred alternative, promising greater accuracy, efficiency, and convenience without compromising the integrity of the samples. This paper delves into the application of five advanced non-destructive testing technologies in the realm of meat tenderness assessment. These include near-infrared spectroscopy, hyperspectral imaging, Raman spectroscopy, airflow optical fusion detection, and nuclear magnetic resonance detection. Each technology is scrutinized for its respective strengths and limitations, providing a comprehensive overview of their current utility and potential for future development. Moreover, the integration of these techniques with the latest advancements in artificial intelligence (AI) technology is explored. The fusion of AI with non-destructive testing offers a promising avenue for the development of more sophisticated, rapid, and intelligent systems for meat tenderness evaluation. This integration is anticipated to significantly enhance the efficiency and accuracy of quality assessment in the meat industry, ensuring a higher standard of safety and nutritional value for consumers. The paper concludes with a set of technical recommendations aimed at guiding the future direction of non-destructive, AI-enhanced meat tenderness detection, thereby contributing to the ongoing improvement of the meat industry in China and beyond.

This paper aims to build up a preference function to evaluate the public benefits of the type of agricultural farming, biodiversity, water provisions, land use type, ecotourism modes, and a monetary attribute (environmental trust fund and willingness to contribute) associated with an ecosystem service and land use program in a forest park. This study used the choice experiments to build a random utility model, analyze the average preference for the above land use attributes based on the conditional logit and used a latent class model to test the resident’s heterogeneous preferences for land use planning in the forest park. We also estimated the welfare derived from various land use programs. The empirical result had shown that: (1) increasing organic farming area, maintaining the status quo of species biodiversity, increasing the surface water provision, increasing the area of custom flora, increasing the wetland area, and setting up an integrated framework for ecotourism increase the public’s preference for the land use program; (2) we found that farmer and non-farmer haven’t the same land use preferences; (3) the ecotourism development program incorporating biodiversity, organic farming, ethnobotany, and wetland area with integrated ecotourism are more preferred than other land use program scenarios.

The electroencephalogram (EEG) is a record of brain activity. Brain Computer Interface (BCI) technology formed by the EEG signal has become one of the hotspots at present. How to extract the feature signal of EEG is the most basic research of BCI technology. In this paper, A new method of recognizing fatigue, conscious, concentrated state of human brain is proposed by the combination of discrete wavelet transform and the neural network based on EEG signal. First of all, the law signal is preprocessed by the wavelet denoising method because the law EEG signal contains a large number of high frequency noise, which is decomposed into multi-layer high frequency signal and low frequency signal. thus, δ wave, θ wave, α wave, β wave are obtained by the wavelet transform. And then, frequency band energy of the different wave is regards as the feature signal of EEG. In the experiment, the feature signal is classified by radial basic function (RBF) and annealed chaotic competitive learning network (ACCLN). RBF and ACCLN networks are trained with 500 sets of sample data and are tested by 100 sets of samples in different mental states. The experimental results show that the average accuracy of RBF network under three conditions are 88.75%, 88.25%, 88.5%, respectively, and the correct rate of ACCLN network is 97%, 98%, 98%, respectively.

Concrete is more stable than filler as a false roof in a downward approach type infill quarry, but the mechanical model of a concrete false roof is not clear. As a result, there has been limited application. Therefore, it is necessary to establish the mechanical model of a concrete artificial false roof to enhance the stability of the downward approach infill quarry. This paper combines theoretical analysis, model derivation, finite element analysis and field application methods. Firstly, the basic assumptions of thin plate theory and elasticity mechanics are used as the premise to establish the differential equations of the deflection curve of the concrete thin plate false roof. Then, the three types of bending moment generation of the concrete thin plate false roof are explored. Secondly, the relationship between the location of dangerous surface and dangerous point in hard-supported weak-slab structure and soft-supported weak-slab structure is analyzed, and the type of uniform load and calculation model of concrete thin-slab false roof are improved. Finally, according to the established mechanical model of thin slab false roof, finite element analysis and field application were carried out. The results show that there are three types of deflection curve differential equations in the concrete thin slab false roof perpendicular to the strike, and three extreme points exist in the middle section of the thin slab and on both sides of the surrounding rock. The hazardous surface of the hard-supported weak-slab structure is present at the intersection of the encircling rock and the thin-slab fake ceiling, with the perilous point situated on the top of this surface. The hazardous surface of the soft-supported weak-slab structure can be found in the centre section of the thin-slab fake ceiling, with the perilous point being located at the bottom of this surface. Moreover, the damage mode for both structures is that of maximum tensile stress damage. Upon conducting a finite element analysis, the results indicate that the concrete's maximum tensile stress is significantly high.

The SK model proposed by Sherrington and Kirkpatrick is an important mean field model for spin glasses. The dependence structure of Hamiltonians of the SK model is considered in this paper. We have investigated the covariance matrix of Hamiltonians of the SK model, and establish a relationship between the rank of the corresponding covariance matrix and the dimension of the space spanned by the Hamiltonians. Finally, we also give an upper bound for the rank of the covariance matrix, which might be the best.

A portable laser photoacoustic sensor based on a Field-Programmable Gate Array (FPGA) is reported for methane detection. A tunable DFB diode laser in the 1654 nm wavelength range is used as an excitation source. The photoacoustic signal processing was implemented by a FPGA device. A small resonant photoacoustic cell is designed. The minimum detection limit (1σ) of 10 ppm for methane (CH₄) is demonstrated.

Hepatic carboxylesterase 1(CES1) metabolizes many prodrugs into active ingredients or direct-acting drugs into inactive metabolites. We aim to develop a semi-physiologically based pharmacokinetic model(Semi-PBPK model) to simultaneously predict pharmacokinetics of CES1 substrates and their active metabolites in liver cirrhosis(LC) patients. Six prodrugs(enalapril, benazepril, cilazapril, temocapril, perindopril and oseltamivir) and three direct-acting drugs (flumazenil, pethidine and remimazolam) were selected. The parameters including organ blood flows, plasma binding protein concentrations, functional liver volume, hepatic enzymatic activity, glomerular filtration rate(GFR) and gastrointestinal transit rate were introduced into the simulation. Pharmacokinetic profiles of these drugs and their active metabolites were simulated in 100 virtual subjects. The developed semi-PBPK model, following validation in healthy subjects, was extrapolated to LC patients. Most of the observations are within the 5% and 95% quantile of simulations from 100 virtual patients. The estimated AUC and Cmax are within 0.5-2-fold of observation. The sensitivity analysis showed that the decreased plasma exposure of active metabolite due to the decreased CES1 was partly attenuated by the decreased GFR. Conclusion: The developed PBPK model has successfully predicted pharmacokinetics of CES1 substrates and their metabolites in healthy subjects and LC patients, which assists in tailoring dosages of CES1 substrates in LC patients.

Currently, in some domestic and foreign mines, the backfill drilling pipeline experience a rupture phenomenon even when the wear degree is low. This results in a delay in production due to the filling becoming 'sick'. This paper presents, for the first time, the damage mechanism from a mechanical perspective and re-derives the anti-extrusion strength model of the backfill drilling pipeline. We investigate the influence of law on the anti-extrusion strength of pipelines from the perspective of stratum and cement ring. We then verify the theoretical and simulation results through engineering examples. The results demonstrate that the Mises stress criterion is a suitable modification principle for the anti-extrusion strength model of the backfill drilling pipeline. The anti-extrusion strength of the pipeline is related to the elastic modulus and Poisson's ratio of the stratum, and the thickness of the cement ring. It is negatively affected by the depth of the stratum. For hard strata, a cement ring with a smaller elastic modulus is suitable, while for soft stratum, a cement ring with a larger elastic modulus is recommended. When the missing angle of the cement ring is less than 60°, the stress concentration factor increases up to 2.2. The stress unloading capacity of the cement ring ranges from 32.7% to 37.8%, and optimal performance of the cement ring is achieved when it has high strength and low rigidity. The backfill filling pipeline of a copper mine abroad was destroyed due to external extrusion force exceeding its anti-extrusion strength value. The modified pipeline anti-extrusion strength model is 18.2% higher than the casing API strength value. This finding can inform the design of the backfill filling pipeline for China's kilometer-deep wells in the future.

To facilitate the computation of the uniaxial compressive strength value of the cemented paste backfill under the condition of high sand-cement ratio, and to analyze the size effect of the cemented paste backfill with high sand-cement ratio under varied aspect ratios, the cemented paste backfill specimens with sand-cement ratios of 8:1-24:1 and aspect ratios of 0.5, 1, and 2 were prepared. Through response surface experiments and finite element analysis, the influence of three aspect ratios on the cemented paste backfill strength was explored, and the failure characteristics and size effect mechanisms of cemented paste backfill with various aspect ratios were analyzed. The model of strength conversion between cemented paste backfill with different aspect ratios was established. The results show that the compressive strength of the cemented paste backfill decreases with the increase of the aspect ratio under the same mass concentration and sand-cement ratio. When the aspect ratio is 0.5 and 1, the splitting failure is the main factor; when the aspect ratio is 2, the shearing failure is the main factor. The three-dimensional stress caused by the end effect of the cemented paste backfill is the main reason for the high strength when the aspect ratio is 0.5. Due to the one-dimensional stress zone generated in the middle of the cemented paste backfill with an aspect ratio of 2 in the laboratory, its strength value is closer to the actual uniaxial compressive strength value of the cemented paste backfill. The strength values of the cemented paste backfill with aspect ratios of 0.5 and 1 were higher than the actual uniaxial compressive strength values in the laboratory. The rationality of the theoretical analysis was verified by the ABAQUS analysis results. According to the experimental results, a strength conversion model between different aspect ratios is established, which can provide a reference for the design of the uniaxial compressive strength of the cemented paste backfill.

The epidemic of Coronavirus Disease 2019 (Covid-19) has brought many changes to people's life. This study aims to analysis Chinese people's psychological change and life after quarantining Wuhan and explore the influencing factors. Based on data from a web-survey after quarantining Wuhan (N=3268), the principal-component-analysis (PCA), multiple-linear-regression (MLR), propensity-score-matching (PSM) were used to explore the psychological change of people in China and the influencing factors. 83.3% of the respondents said that the impact of the epidemic on their life had increased after quarantining Wuhan. A considerable proportion of people's anxiety increased, being reflected in negative emotion, behavioral response and physiological response. The proportion of people who said their anxiety had increased in Wuhan was higher than that in other regions (p <0.05). The anxiety of people who were in medical isolation increased less than those who were not (p <0.05). All three aspects of people’s anxiety were positively related with time of medical isolation and degree of the attention on the epidemic (p＜0.05) except the effect of attention degree on the physiological response (p＝0.06). The measure of medical isolation at home should be advocated. Yet people should reduce the concern for the epidemic while paying attention to self-protection.

In this work, a novel single crystal (3-(4-chlorophenyl)-4,5-dihydroisoxazol-5-yl)methyl benzenesulfonate has been synthetized via a one-pot sequential strategy under sonication. A single crystal X-ray diffraction analysis was reported. In the crystal, a layer structure is generated by C—H···O and C—H···N hydrogen bonds. A Hirshfeld surface analysis indicates that the most important contributions to the crystal packing are from H···H (28.9%), H···O/O···H (26.7%) and H···C/C···H (15.8%) interactions. The optimized structure calculated using density functional theory at the B3LYP/6–311 G+(d,p) level is compared with the experimentally determined structure in the solid state. The calculated highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) energy gap is 4.6548 eV.

China's economic development has shifted from high speed to high quality. This study constructs an evaluation index for China’s high-quality development utilizing a new development concept. The entropy method and cluster analysis were used to assess the level of high-quality development in China between 2015 and 2021. Kernel density estimation method was employed to explore spatiotemporal dynamics. The results reveal significant differences in the level of economic development among provinces in China; the eastern region is significantly better than the central, northeastern, and western regions. From the perspective of the sub-item evaluation, challenges with uneven, uncoordinated, and insufficient economic development exist in various Chinese provinces.

Abstract: The EMU(electric multiple units) traction motors are powered by converters. The PWM(pulse width modulation) voltage increases the voltage stress borne by the motor insulation system, making the ITSC(inter-turn short-circuit) fault more prominent. An index based on short-circuit thermal power was proposed in the article to evaluate the non-metallic ITSC faults degree. The apFFT(all phase FFT) time-shift phase difference correction with double Hanning-windows is used to calculate the fundamental frequency of the traction motor's ZSVC（zero se-quence voltage component）, the fundamental amplitudes of ZSVC and three-phase current. The five parameters are used as fault features to train the SVM (support vector machine)fault diagnosis model. The SVM hyper-parameters C and g are optimized by K-CV (K fold cross-validation) and grid search methods. The experimental verification was carried out by the EMU electric traction simulation experimental platform. According to the non-metallic degree index proposed in this article, the experimental samples were divided into three categories, normal, incipient and serious fault samples. The ITSC fault diagnosis accuracy was 100% on the training data set and 93.33 % on the test data set. There was no misclassification between normal and serious ITSC fault samples.

Driving factors of smart city construction are exploratively studied by grounded theory method based on text sources from journal papers in SCI and CSSCI databases. Initial scale of driving factors about smart city construction is obtained on the basis of above analyses. This paper modifies measuring items of the initial scale with a small sample pretest and reliability test, then forms final items by exploratory factor analysis. According to the above scale, questionnaires are designed to obtain empirical data, and confirmatory factor analysis is used to verify further validity and reliability of the scale. The results show that driving factors of smart city construction include three main dimensions: problem-oriented factors, business- or technology-driven factors and endogenous development requirements.

Early diagnosis and treatment have always been highly desired in the fight against cancer, and detection of circulating tumor DNA (ctDNA) has recently been touted as highly promising for early cancer screening. Consequently, the detection of ctDNA in liquid biopsy gains much attention in the field of tumor diagnosis and treatment, which has also attracted research interest from the industry. However, traditional gene detection technology is difficult to achieve low cost, real-time and portable measurement of ctDNA. Electroanalytical biosensors have many unique advantages such as high sensitivity, high specificity, low cost and good portability. Therefore, this review aims to discuss the latest development of biosensors for minimal-invasive, rapid, and real-time ctDNA detection. Various ctDNA sensors are reviewed with respect to their choices of receptor probes, detection strategies and figures of merit. Aiming at the portable, real-time and non-destructive characteristics of biosensors, we analyze their development in the Internet of Things, point-of-care testing, big data and big health.

A single paragraph of about 200 words maximum. For research articles, abstracts should give a pertinent overview of the work. We strongly encourage authors to use the following style of structured abstracts, but without headings: (1) Background: Place the question addressed in a broad context and highlight the purpose of the study; (2) Methods: briefly describe the main methods or treatments applied; (3) Results: summarize the article's main findings; (4) Conclusions: indicate the main conclusions or interpretations. The abstract should be an objective representation of the article and it must not contain results that are not presented and substantiated in the main text and should not exaggerate the main conclusions.

An eight-sided prism sample, obtained from a hot-rolled AZ31 magnesium alloy sheet, was compressed at room temperature along the transverse direction to investigate the influence of local strain on twinning behavior using electron backscatter diffraction (EBSD) measurements. The octagonal surface of the sample was divided into distinct regions based on hardness distribution and metallographic observations. The EBSD maps of different areas show significant variations, suggesting that these areas experienced different local strain conditions. The EBSD measurements provided detailed data from three distinct regions, with the strain state known in two regions and uncertain in the third. The combined analysis of the Schmid factor (SF) and the strain compatibility factor (m') was employed to study twin variant selection. The comparison of twinning behavior in different regions showed that the strain compatibility factor offered a more comprehensive explanation for the observed twinning pattern in the region with local shear strain.

The nuclear factor-ĸB (NF-ĸB) transcriptional system is a major effector pathway involved in inflammatory responses. Previous studies found that a Gardenia decoction (GD) inhibited the expression of NF-κB in a lipopolysaccharide (LPS)-stimulated mouse intestinal injury model. Herein, we hypothesized that geniposide (GE), a component of Gardenia jasminoides Ellis, also exerts anti-inflammatory effects and inhibits NF-ĸB activity in LPS-induced intestinal epithelial cells (IEC-6). IEC-6 cells were stimulated with LPS, following which the effects of GE on NF-ĸB signaling in the IEC-6 cells were examined by western blotting to detect IĸB phosphorylation/degradation. The expression of NF-κB was determined by immunofluorescence assay (IFA). Enzyme-linked immunosorbent assay (ELISA) was used to detect the inhibitory effect of GE on the release of tumor necrosis factor-α (TNF-α), interleukin-6 (IL-6) and interleukin-1β (IL-1β) activated by LPS in IEC-6 cells. In addition, the migration ability of IEC-6 cells was observed by the scratch method. These results showed that GE dose-dependently downregulated levels of the proinflammatory cytokines TNF-α, IL-6 and IL-1β that had been upregulated by LPS and suppressed the phosphorylation of IĸB and NF-ĸB induced by LPS. Our findings indicated that GE could reduce LPS-induced NF-ĸB signaling and proinflammatory expression in IEC-6 cells and significantly enhance the migration of IEC-6 cells. Moreover, GE inhibited the expression of NF-κB, nuclear transfer, and transcriptional activity in IEC-6 cells. GE could block the synthesis of inflammatory factors of IEC-6 cells by inhibiting activation of the IĸB/NF-κB signaling pathway induced by LPS.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

Since the electro-hydraulic servo shaking table exists many nonlinear elements, such as, dead zone, friction and blacklash, its acceleration response has higher harmonics which result in acceleration harmonic distortion, when the electro-hydraulic system is excited by sinusoidal signal. For suppressing the harmonic distortion and precisely identify harmonics, a combination of the adaptive linear neural network and least mean M-estimate (ADALINE-LMM), is proposed to identify the amplitude and phase of each harmonic component. Namely, the Hampel’s three-part M-estimator is applied to provide thresholds for detecting and suppressing the error signal. Harmonic generators are used by this harmonic identification scheme to create input vectors and the value of the identified acceleration signal is subtracted from the true value of the system acceleration response to construct the criterion function. The weight vector of the ADALINE is updated iteratively by the LMM algorithm, and the amplitude and phase of each harmonic, even the results of harmonic components, can be computed directly online. The simulation and experiment are performed to validate the performance of the proposed algorithm. According to the experiment result, the above method of harmonic identification possesses great real-time performance and it has not only good convergence performance but also high identification precision.

The carbonyl iron particles were dispersed in a polychloroprene rubber (CR) matrix under an external magnetic field for practical application as microwave absorption composites film. The film prepared under external magnetic field with a thickness of only 0.54 mm showed least reflection loss of -15.98 dB and the reflection loss value less than -10.0 dB over the frequency range of 11.4~14.8 GHz. In comparison with the microwave absorption properties of calculation by transmission line theory based on the tested relative complex permittivity and permeability and film prepared by general route without external magnetic field, the film made with external magnetic field exhibited more excellent microwave absorption properties, strongly depending on the increment of anisotropy and rearrangement of magnetic particles. The results indicated the composite film made under external magnetic field have excellent microwave absorption properties, which suggest that the composites thin film could be used as a thinner and lighter microwave absorber.

This literature review paper delves into the synergies between Climate-Smart Agriculture (CSA) and the effective management of food losses. With the escalating challenges posed by climate change and the pressing need to address food security concerns, the intersection of these two critical domains becomes paramount for sustainable agricultural practices. The review explores existing research on the implementation of climate-smart agricultural techniques and their impact on mitigating food losses throughout the agricultural value chain. The paper synthesizes findings related to climate-resilient crop varieties, precision farming, water-use efficiency, and sustainable soil management, highlighting their contributions to reducing post-harvest losses and enhancing overall food security. In addition to summarizing current knowledge, this paper identifies gaps in the literature and proposes avenues for future research. This review serves as a foundation for researchers, policymakers, and practitioners seeking to contribute to the advancement of climate-smart agriculture and the reduction of food losses, paving the way for a more sustainable and resilient global food system.

This study investigates the impact of specimen size on the mechanical properties of wood, specifically focusing on compression strength, elastic modulus, and Poisson's ratio. Compression tests were conducted using three different specimen sizes (20mm×20mm×30mm, 40mm×40mm×60mm, 60mm×90mm×90mm) in the longitudinal, radial, and tangential directions. Mechanical parameters, failure mechanisms, load-displacement curves, and stress-strain relationships were systematically analyzed for each size. The study also evaluated the influence of specimen size on the accuracy of finite element numerical simulations by utilizing the obtained mechanical parameters. The results reveal a significant correlation between compressive strength and specimen size, indicating a decrease in compressive strength with increasing specimen size. Conversely, elastic modulus and Poisson's ratio exhibit less sensitivity to variations in specimen size. Notably, parameters derived from small-sized specimens (20mm×20mm×30mm) exhibited substantial errors, while those obtained from medium-sized (40mm×40mm×60mm) and large-sized specimens (60mm×90mm×90mm) demonstrated greater reliability, providing precise results in finite element numerical simulations.

The AREB/ABF (ABA response element binding) proteins in plants are vital for plant stress responses, but the understanding of AREB/ABFs in orchid species, an important traditional medicinal and ornamental plants, is limited. Here, twelve AREB/ABF genes were identified within three orchids’ complete genome and classified into three groups (groups I, II, and III) via a phylogenetic analysis, which was further supported by the analysis of their conserved motifs and gene structures. The cis-elements analysis showed that hormone response elements followed by light and stress responses were widely rich in AREB/ABFs. A prediction analysis of orchid ABRE/ABF-mediated regulatory network was further constructed through cis-regulatory elements (CREs) analysis of their promoter regions and revealed that several transcriptional factor (TF) gene family were abundant as the potential regulators for orchid AREB/ABFs. Expression profile analysis based on public transcriptomic data showed that most AREB/ABF genes have distinct tissue-specific expression patterns in orchid plants. Additionally, DcaABI5 as the homolog of ABA INSENSITIVE 5 (ABI5) from Arabidopsis was selected for further analysis. The results showed that Arabidopsis transgenic overexpressing DcaABI5 could rescue the ABA insensitive phenotype in the mutant abi5. Collectively, these findings will provide valuable information on AREB/ABF genes in orchids.

The soybean yield per unit area and soybean acreage are increased to boost overall soybean production as two effective solutions. There is a large area of saline soils in northeast China, where if soybeans could be grown with the help of isolated saline-tolerant rhizobia, the cultivation area of soybeans in China can be effectively expanded. Several rhizobia with different salt-, acid- and alkali-resistant characteristics were obtained in this research by isolating, identifying, and analyzing the nitrogen-fixing activities of indigenous rhizobia from different soybean planting soils, and further analyzed the host compliance between rhizobia and different soybean germplasm concerning 30 representative germplasm resources in the northeast region. Collectively, the results of the resistance study of HLNEAU2 isolated from the Shaanxi region are great references for guiding the application of rhizobia on soybeans.

There are rich proper noun derivative semantic relationships in geographic entity vector data. The identification of traditional proper noun derivative semantic relationships usually requires toponym researchers to examine the source of derived toponyms by consulting a large number of toponym documents. This method cannot adapt to the mining of proper noun derivative semantic relationships for large-scale geographical entity. In this regard, this paper proposes a method of identifying the proper noun derivative semantic relationships for geographical entity by combining prompt learning and XGBoost model. This method transforms the extraction problem of proper noun derivative semantic relationships into a binary classification problem by analyzing the characteristics of the derivation relationship of toponyms in the form of toponyms and the spatial and temporal distribution of geography. Firstly, prompt learning and gaussian mixture model are used to extract and cluster the derivation words of toponyms, so as to realize the recognition of derived toponyms collections. Then, enumerate the possible proper noun derivations in the toponym set, and then the XGBoost model is used to identify the semantic relations derived from the proper noun of geographical entities. In the experiment, the recognition method of proper noun derivative semantic relationships based on prompt learning and XGBoost proposed in this paper has achieved good relationship recognition effect in the experiment. This method has certain practical value in the fields of toponym management and toponym translation.

We suppose that a Cooper pair (CP) will experience a damping force exerted by the condensed matter. A Langevin equation of a CP in two dimensional condensed matter is established. Following a method similar to Nelson's stochastic mechanics, generalized Schr\"{o}dinger equation of a CP in condensed matter is derived. If the CPs move with a constant velocity, then the corresponding direct current (DC) electrical conductivity can be calculated. Therefore, a Drude like formula of resistivity of CPs is derived. We suppose that the damping coefficient of CPs in two dimensional cuprate superconductors is a linear function of temperature. Then the resistivity and scattering rate of CPs turn out to be also linear-in-temperature. The origin of linear-in-temperature resistivity and Planckian dissipation in cuprate superconductors may be the linear temperature dependence of the damping coefficient of CPs.

Intense climate change and rapid urbanization have increased the risk of urban flooding, seriously affecting urban economic and social stability. Enhancing the urban flood resilience (UFR) has required a new solution to cope with urban flood disasters. In this study, taking Yingtan city as an example, a system of indicators for evaluating UFR was constructed, with 17 representative indicators, comprising three subsystems: socio-economic, ecological and infrastructural. A hybrid (FAHP-EWM)-TOPSIS model was applied, to develop an index-based measurement to compare and evaluate UFR, and Gray Relational Analysis (GRA) was used to discover the main factors affecting UFR. In addition, the natural discontinuous method was innovatively used to divide the UFR grade interval into levels, and the grade change was evaluated based on the TOPSIS method. The results showed that (1) from 2010 to 2022, the UFR in Yingtan City increased by 80.69%, and the factors affecting UFR are highly correlated with urban infrastructure development. However, the ecological resilience in the subsystem showed a fluctuating downward trend, because of the influence of the surface area of lakes and rivers. (2) The grades of UFR for Yingtan City increased from Level III (2010 and 2016) to Level IV (2022), with local financial expenditures and the age structure of the population being the main factors currently limiting the development of UFR. The study provides a theoretical basis for the construction of an indicator system for assessing the UFR of Yingtan and proposes practical improvement directions for UFR.

Distributed/semi-distributed models are considered to be sensitive to the spatial resolution of the data input. In this paper, we take a small catchment in high urbanized Yangtze River Delta, Qinhuai catchment as study area, to analyze the impact of spatial resolution of precipitation and the potential evapotranspiration (PET) on the long-term runoff and flood runoff process. The data source includes the TRMM precipitation data, FEWS download PET data, and the interpolated metrological station data. GIS/RS technique was used to collect and pre-process the geographical, precipitation and PET series, which were then served as the input of CREST (Coupled Routing and Excess Storage) model to simulate the runoff process. The results clearly showed that, the CREST model is applicable to the Qinhuai catchment; the spatial resolution of precipitation had strong influence on the modelled runoff results and the metrological precipitation data cannot be substituted by the TRMM data in small catchment; the CREST model was not sensitive to the spatial resolution of the PET data, while the estimation fourmula of the PET data was correlated with the model quality. This paper focused on the small urbanized catchment, suggesting the influential explanatory variables for the model performance, and providing reliable reference for the study in similar area.

This research focuses on the Hopf bifurcation occurring at a singular point with high-order degeneracy in a class of three-dimensional systems. Based on center manifold theorem, by expanding the technique for determining singular point values of degenerate singularities in two-dimensional systems, the formal series method to determine the singular point values at the high-order degenerate critical point is discussed. Furthermore, a class of specific three-dimensional differential systems with high-order degenerate singularities is explored. By computing the singular point values and determining center conditions, we proved that a minimum of 5 small-amplitude limit cycles in the vicinity of the origin. This research provides new perspectives on the center problem and limit cycle bifurcation in high-dimensional systems with high-order degenerate singular points.

L-Theanine, a unique non-protein amino acid, is an important bioactive component of green tea. Previous studies have shown that L-theanine has many potent health benefits, such as anti-anxiety effect, regulation of immune response, relaxing neural tension, reducing oxidative damage. However, little is known concerning whether L-theanine can improve the clearance of mitochondrial DNA (mtDNA) damage in organisms. Here, we reported that L-theanine treatment increased ATP production and improved mitochondrial morphology to extend the lifespan of UVC-exposed nematodes. Mechanistic investigations showed that L-theanine treatment enhanced the removal of mtDNA damage and extended lifespan by activating autophagy, mitophagy, mitochondrial dynamics, and mitochondrial unfolded protein response (UPRmt) in UVC-exposed nematodes. In addition, L-theanine treatment also up-regulated the expression of genes related to mitochondrial energy metabolism in UVC-exposed nematodes. Our study provided a theoretical basis for the possibility that tea drinking may prevent mitochondrial related diseases.

The near-infrared (NIR) organic dyes with strong ultrafast nonlinear optical (NLO) activities are of importance for various applications. However, such kinds of dyes are still scarce. In this work, we have compared the NLO properties of two NIR Aza-BODIPY derivatives, in which the strong electron-donating groups, namely 4-(N, N-dimethylamino) phenyl and 1-ethyl-1,2,3,4-tetrahydroquinoline groups, are connected with the cores of Aza-BODIPY. Z-Scan experimental results show that two Aza-BODIPY derivatives exhibit strong saturation absorption and large modulation depth under the excitation of femtosecond pulses at 800 nm. Under 1300 nm excitation, two derivatives exhibit strong nonlinear refraction. In addition, the Aza-BODIPY derivatives also display effective two-photon excited fluorescence emission in the wavelength range of 1200-1600 nm. Based on the experimental results, it is found that 1-ethyl-1,2,3,4-tetrahydroquinoline group can more effectively enhance the NLO properties of Aza-BODIPY derivatives compared with the 4-(N, N-dimethylamino) phenyl group, thus providing new possibilities for the design and development of NIR NLO materials.

The association between normal-range triglycerides and diabetes mortality remains unclear. This cohort study aimed to elucidate this relationship by examining 19,010 US adult participants with fasting serum triglycerides below 150 mg/dL. Cox proportional hazards models were employed to estimate mortality hazard ratios (HRs) and 95% confidence intervals (CIs). Participants were followed up for a mean of 15.3 years, during which 342 diabetes deaths were recorded. A 1-natural-log-unit increase in triglycerides was associated with a 57% higher risk of diabetes mortality (adjusted HR, 1.57; 95% CI, 1.04–2.38). Comparable results were obtained when triglycerides were analyzed in quartiles. Receiver operating characteristic curve analysis identified an optimal triglyceride cutoff of 94.5 mg/dL for diabetes mortality; individuals with triglyceride levels above this threshold faced a greater risk of diabetes mortality (adjusted HR, 1.43; 95% CI, 1.12–1.83). Further investigation revealed a positive association between normal triglyceride levels and all-cause mortality, though no association was observed between normal triglycerides and mortality from hypertension or cardiovascular disease. In conclusion, elevated triglycerides within the normal range were associated with an increased risk of diabetes mortality. Individuals with triglyceride levels of 95 mg/dL or higher may require vigilant monitoring for diabetes and its associated complications.

An accurate assessment of the stage-discharge relationship in open channel flows is necessary and important to the design and management of hydraulic structures and engineering in practical hydrosystems such as rivers and streams. While the flow structures and patterns at open channel junctions are interesting and have been widely studied in the literature, this paper focuses further on the effect of flow junctions on stage-discharge relationship at mountain river confluences. In this study, both the flume and physical model experiments are designed and performed carefully to test and analyze the complex flow structures and characteristics at river confluences with different configurations and hydraulic conditions. The impacts of the flow junctions on the traditional stage-discharge relationship are analyzed in this study. The results of this study are discussed in the paper for the understanding of flow structures at flow junctions and the design and management of hydraulic structures in river engineering.

The Yixian Formation (Lower Cretaceous) of China is famous worldwide for its fossils of early angio-sperms, but there is only one record of flower bud hitherto. A previous fossil record of flower bud just showed the appearance and lacked any internal details. Such a lacuna in knowledge of flower buds hin-ders our understanding of the evolution of flowers. Our new specimen was collected from an outcrop of the Yixian Formation (the Barremian-Aptian, Lower Cretaceous) near Dawangzhangzi, Lingyuan, Liao-ning, China. The specimen was observed and photographed using a Sony ILCE-7 digital camera and a Nikon SMZ1500 stereomicroscope, and details were observed using a TESCAN MAIA3 SEM. Our ob-servations document a fossil flower bud, Archaebuda cretaca sp. nov, from the Lower Cretaceous of China. The occurrence of two species of Archaebuda in the Yixian Formation not only confirms the ex-istence of the expected gynoecium (and possible androecium) in a flower bud, but also underscores the occurrence of typical flowers in the Early Cretaceous.

Focused microwave breast hyperthermia (FMBH) employs a phased antenna array to perform beamforming that can focus microwave energy at targeted breast tumors. Selective heating of the tumor endows the hyperthermia treatment with high accuracy and low side effects. The effect of FMBH is highly dependent on the applied phased antenna array. This work investigates the effect of polarizations of antenna elements on the microwave focusing results by simulations. We explore two kinds of antenna arrays with the same number of elements using different digital realistic human breast phantoms. The first array has all the elements’ polarization in the vertical plane of the breast while the second array has half elements’ polarization in the vertical plane and the other half in the transverse plane, i.e., cross polarization. In total 96 sets of different simulations are performed, and the results show that the second array leads to a better focusing effect in dense breasts than the first array. This work is very meaningful for the potential improvement of the antenna array for FMBH, which is of great significance for the future clinical applications of FMBH. The antenna array with cross polarization can also be applied in micro-wave imaging and sensing for biomedical applications.

The foot-mounted inertial navigation system is an important application of pedestrian navigation as it in principle does not rely any external assistance. A real-time range decomposition constraint method is proposed in this paper to combine the information of dual foot-mounted inertial navigation systems. It is well known that low-cost inertial sensors with ZUPT (zero-velocity update) and range decomposition constraint perform better than in either single way. This paper recommends that the distance of separation between the position estimates of feet-mounted inertial navigation systems be restricted in the ellipsoidal constraint which relates to the maximum step and leg height. The performance of the proposed method is studied utilizing experimental data. The results indicate that the method can effectively correct the dual navigation systems’ position over the existing spherical constraint.

Open-vocabulary learning has recently gained prominence as a means to enable image segmentation for arbitrary categories based on textual descriptions. This advancement has extended the applicability of segmentation systems to a broader range of generally purpose scenarios. However, current methods often revolve around specialized architectures and parameters tailored to specific segmentation tasks, resulting in a fragmented landscape of segmentation models. In response to these challenges, we introduce OVAMTSeg, a versatile framework designed for Open-Vocabulary and Multitask Image Segmentation. OVAMTSeg harnesses adaptive prompt learning to empower the model to capture category-sensitive concepts, enhancing its robustness across diverse multi-task and scenario contexts. Text prompts are employed to effectively capture semantic and contextual features of the text, while cross-attention and cross-modal interactions enable the fusion of image and text features. Furthermore, a transformer-based decoder is incorporated for dense prediction. Extensive experimental results underscore the effectiveness of OVAMTSeg, showcasing its state-of-the-art performance and superior generalization capabilities across three segmentation tasks. Notable achievements include a 47.5 mIoU in referring expression segmentation, 51.6 mIoU on Pascal-VOC with four unseen classes, 46.6 mIoU on Pascal-Context in zero-shot segmentation, 65.9 mIoU on Pascal-5i, and 35.7 mIoU on COCO-20i datasets for one-shot segmentation.

This paper presents a piezoresistive pressure sensor with a shield layer for improved stability. Compared with the conventional piezoresistive pressure sensors, p-type piezoresistors are covered by an n-type shield layer, which is formed by ion implantation. The proposed pressure sensors have been successfully fabricated by bulk micromachining techniques. The impact of electrical field on piezoresistors is studied by simulation. The temperature drift of the pressure sensor has been investigated by both simulation and experimental measurement. Characteristics of developed pressure sensors are tested from -40 C to 125 C. A sensitivity of 0.022 mV/V/KPa and a maximum non-linearity of 0.085% FS are measured for the fabricated sensor in a pressure range of 1 MPa. The temperature coefficients of resistance of shielded piezoresistors are found to be smaller than those of un-shielded ones. It is demonstrated that the shield layer is able to reduce the drift caused by electrical field and ambient temperature variation.

The integrated stress response (ISR) is an adaptational signaling pathway that is induced in response to different stimuli, such as accumulation of unfolded and misfolded protein, hypoxia, amino acid deprivation, viral infection and ultraviolet light. It has been known that viral infection can activate ISR, but the role of ISR during viral infection is still unclear. In some cases, ISR is a protective mechanism of host cell against infection with virus whilst ISR may be hijacked by viruses for facilitating its replication. In this review, we highlighted recent advances on induction of ISR upon viral infection and the downstream responses involved such as autophagy, apoptosis, formation of stress granules and innate immunity response. We then discussed the molecular mechanism of ISR regulating viral replication and how viruses antagonize this cellular stress response resulting from ISR.

We study a two-echelon supply chain made up of a supplier and a manufacturer, both of which can reduce their component/product carbon emissions. With the vertical technology spillovers, we explore the optimal decisions of centralized and decentralized supply chains with price dependent demand and propose coordination strategy for the decentralized supply chain. Considering the cost contraction effectiveness of the technology spillovers, the centralized and decentralized game theoretic models of a two-echelon supply chain are developed to investigate optimal decisions of pricing and carbon emissions reduction. Through a systematic comparison and numerical analysis, we show that the profits of both players and the entire supply chain improve with the effect of technology spillovers increasing. Carbon emissions reduction will be taken by various protective measures so that the supplier and the manufacturer who do not innovate can hardly share the results of innovating via the “free-riding” methods when the technology spillover is relatively small. We also propose a revenue-cost sharing contract through bargaining to enhance the performance of the decentralized supply chain.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.

Intermetallic compounds are increasingly being expected to utilize in tribological environments, but to date the works are hindered by insufficient ductility at low and medium temperature. This paper presents a novel multiphase intermetallic alloy with the chemical composition of Mo-40Ni-13Si (at.%). Microstructure characterization reveals that a certain amount of ductile Mo phases formed during the solidification process of ternary Mo-Ni-Si alloy melt, which is undoubtedly beneficial to the ductility improvement of intermetallic alloy. Tribological properties of the designed alloy, including wear resistance, friction coefficient and metallic tribological compatibility, were evaluated under dry sliding wear test conditions at room temperature. Results suggested that the multiphase alloy possesses an excellent property for room-temperature wear applications, which is attributed to the unique microstructural features and thereby good combination in hardness and ductility. The corresponding wear mechanism is also reported by observing the worn surface, subsurface and wear debris of alloy, which to be found is soft abrasive wear.

Reverse water gas shift reaction (RWGS) is an important process which plays a vital role in many CO2 utilization related reactions. Noble metals are the most active catalysts in RWGS, but the high price and low reserve strangled their applications. In the present work, we reported a non-transition-metal MgAl2O4 catalyst which showed outstanding activity and stability at high temperatures in the RWGS reaction and improved performance after doping of single atomic Nin+. The catalyst can obtain 46% of CO2 conversion in durability test of 75 h at 800 °C under high weight hourly space velocities (225 000 ml g-1 h-1). The adsorption sites, possible reaction route, and effects of Nin+ single atoms on the (111) surface of MgAl2O4 for RWGS were investigated by in situ DRIFTS and DFT calculations. The results indicated that the rate determining reaction step of RWGS on MgAl2O4 and Ni (SA)/MgAl2O4 were both the reaction of OH* + H* → H2O* + *, but the energy barrier was significantly reduced after introducing single atomic Nin+. Nin+ atoms can increase the hydroxyl coverage on the surface of catalyst and Al3+ sites near the Nin+ ion are considered as the predominant active sites for RWGS reactions.

Compressed carbon dioxide energy storage (CCES) offers several benefits over other existing energy storage systems, including ease of liquefaction, high energy storage density, and environmental friendliness. As a result, the research progress, economic and technological feasibility, and system operation of the CCES system are all discussed in depth in this study. The system evaluation method is summarized and the compressed carbon dioxide storage is analyzed, and the performance optimization direction of the compressed carbon dioxide energy storage technology is discussed. When the overall performance of a transcritical CCES system, a supercritical CCES system and a liquid CCES system are compared, it is discovered that the supercritical CCES system has better thermodynamic characteristics and a simpler system configuration, making it suitable for large-scale development and use. The goal of the CCES system's future development is to create a design with an optimum compression and expansion ratio, a more precise analysis and system model, and multi-field coupling. This review's discussion serves as a guide for the best design and use of the CCES system.

Observe the synergistic effect and dose-effect relationship of Trimethoprim (TMP) on bactericidal activity with Flos Lonicerae in vitro. Microamount chessboard dilution method was conducted to determine the minimal inhibitory concentration (MIC) of Trimethoprim, Flos Lonicerae, as well as the combination of Trimethoprim and Flos Lonicerae separately against Staphylococcus aureus, Escherichia coli in vitro and Salmonella. The pour plate count method was used to determine the combined bactericidal activity of Flos Lonicerae combined with Different concentrations TMP. The results showed that the MIC values of the combination of Flos Lonicerae with TMP was much less than the MIC values of the independent use of Flos Lonicerae or TMP, The FIC values of the combination of Flos Lonicerae with TMP were between 0.5 and 1, there was additive effect between them. The bactericidal rates were fitted with least square method, the 95% confidence intervals of the optimal blending quantity about the combination of Flos Lonicerae with TMP on the test organisms were 231μg·mL^-1-249μg·mL^-1, 237μg·mL^-1-259μg·mL^-1, and 235 -259μg·mL^-1

Water quality assessment in pastoral of Tibetan Plateau, which is water sources for about 40% of world's population and the runoff-yield area of Yellow rivers, is very important. In this paper, Xiahe county which belongs to Tibetan Plateau pastoral was investigated. Six parameters(via, chloride, COD, ammonia nitrogen, nitrate, fluoride, sulfate) were selected to assess the water quality and health degree by using fuzzy comprehensive evaluation methods. The hydrochemical type in surface water was of HCO3--Mg2+-Ca2+ type. The cations and anions in surface water were mainly from weathering and dissolution of carbonate rock. Results showed that the water quality in all 69 sampling sites was all of class Ⅰ. The integrated health degree reached more than 0.85 and the health rate were 100%. Although ammonia nitrogen was regarded as the main contamination factor, but it had a little effect on the entire body of water. Overall, the surface water qualities of most samples in Xiahe County was good condition.

A large core size and bending resistance are very important properties of mid-infrared energy transfer fibers, but large core sizes usually lead to a deterioration of bending properties. A negative-curvature nested node-free anti-resonant hollow-core fiber (AR-HCF) based on quartz is proposed. It was made by adding a nested layer to a previous AR-HCF design to provide an additional anti-resonance region while keeping the gap between adjacent tubes strictly correlated to the core diameter to produce a node-free structure. These features improve the fiber’s bending resistance while achieving a larger core diameter. The simulation results show that the radial air-glass anti-resonant layer is increased by the introduction of the nested anti-resonant tube, and the weak interference overlap between the fiber core and the cladding mode is reduced, so the fiber core’s limiting loss and the sensitivity to bending are effectively reduced. When the capillary wall thickness t of the fiber is 0.71 μm, the core diameter D is 70 μm, the ratio of the inner diameter of the cladding capillary to the core diameter d/D is 0.62, and the diameter of the nested tube is d0=29 μm, the fiber has a lower limiting loss at the wavelength of 2.79 μm, and the limiting loss is 3.28×10-4 dB/m. At the same time, the optimized structure also has good bending resistance. When the bending radius is 30 mm, the bending loss is only 4.72×10-2 dB/m. To our knowledge, this is the first research to achieve an anti-bending low-loss micro-structure hollow fiber with a bending radius of less than 30 mm in the 2.79 μm band. An anti-bending low-loss anti-resonant hollow-core fiber with this structure constitutes a reliable choice for the light guiding system of a 2.79 μm band erbium laser therapy instrument.

Volatile organic compounds (VOCs) released from plants have been correlated with disease-status. Analysis of VOCs using GC-MS is time-consuming, laboratory-based, and requires specialist training. Electronic nose devices (E-nose) provide a portable alternative. Three different E-nose devices were compared to assess how accurately they could detect Mango Twig Tip Dieback and Panama disease in banana. The devices were initially trained on known volatiles, then pure cultures of Pantoea sp., Staphylococcus sp., and Fusarium odoratissimum, and finally, on infected and healthy mango leaves and field-collected, infected banana pseudo-stems. The experiments were repeated three times with six replicates for each host-pathogen pair. The variation between healthy and infected host materials was evaluated by principal component and linear discriminant analysis, cross-validation and chemometric data analysis. GC-MS analysis was conducted contemporaneously and identified an 80% similarity between healthy and infected plant material. The portable C 320 was 100% successful in discriminating known volatiles but had a low capability in differentiating healthy and infected plant substrates. The advanced devices (PEN 3 / MSEM 160) successfully detected healthy and diseased samples with a high variance. The results suggest that E-nose devices are more sensitive and accurate in detecting changes of VOCs between healthy and infected plants compared to headspace GC-MS.

With the development of organizational biology and forced from the EU Cosmetic Regulation (EU/1223/2009) with the complete ban of animal testing for cosmetic purposes, 3D skin models have been widely developed due to their similar physiological structure and metabolic function to native human tissue. 3D skin models for in vitro cosmetic evaluation are still promising alternative methods for evaluating phototoxicity, corrosivity and irritation. These models have been used for early screening and later validation of toxicity and efficacy evaluation by many well-known cosmetic companies. 3D skin models have become an important tool in cosmetic evaluation research. This article reviews the development of 3D skin models and their application in cosmetic evaluation. An outlook on the current application and future technological development directions in the cosmetic field is also presented.

The group delay response of chirped fiber Bragg gratings (CFBG) written in polarization-maintaining fiber can be measured using the beat spectrum of the reflections from the two polarization axis, with a resolution and reproducibility better than 50 fs. The method is theoretically described, and we analyze the effect of group delay ripples (GDR) on the performance of a stretcher-compressor pair used in chirped pulse amplification systems. Ripples with a spectral period of the order of the pulse bandwidth are the most deleterious. Those are readily captured with our method, despite the limit on resolution due to the fiber polarization beat length. As a rule of thumb, the GDR should not exceed half the pulse duration. The reconstructed phase of the CFBG is also used to predict the pulse compression performance for a given device. Measurement of GDR as low as 161 fs is experimentally demonstrated.

Smart City has emerged as the mainstream paradigm for urban governance innovation, sustainable development, and strategy upgrades, which is drawing attention from scholars worldwide. However, current frameworks for Smart City assessment remain incomplete and simplistic. In is paper, 30 national or provincial capitals in China were selected and we designed a tri-dimensional SPI model—Social, Physical, and Information Space—for smart city spatial development assessment. Utilizing methods such as entropy weighting, coupled coordination degree models, and the Dagum Gini coefficient, this study assesses the spatial development and coupled coordination of 30 cities from 2011 to 2019. Finally, by means of BP neural networks, the study examines the contribution of each indicator to the spatial coupled coordination. The results indicated that with a narrowing disparity in development speeds among different regions, the spatial coupled coordination development level of smart capitals in China has steadily increased, presenting a pattern of staggered distribution. Moreover, the IS subsystem plays the most significant role in coupled coordination. The significance of this research lies in its tri-dimensional spatial perspective of the spatial development and coupled coordination differences of the Smart City, providing evidence-based support for the regional layout and optimization in China.

To assure the opacity, an optimal problem is to retain the occurring events sequences as many as possible. Contrary to such problem, the other optimal problem is to preserve the minimal occurring events sequences. In the paper, based on the choosing cost, an optimal opacity-enforcing model is presented to minimize the sum of discount choosing cost, which is not only to preserve the opacity, but also to retain the secret to the maximum. To solve the model, two scenarios on opacity are considered. For the two scenarios, some algorithms are presented to achieve the optimal solution for the model by using the method of dynamic programming. And then, the solutions produced by the algorithms are proved correctly by theoretical proof. Finally, some illustrations for the algorithms are given.

Recycling waste products is an environmental-friendly activity that can bring benefits to accompany, saving manufacturing costs and improving economic efficiency. For the beer industry, recycling bottles can reduce manufacturing costs and reduce the industry's carbon footprint. This paper presents a model for a multi-objective collection-distribution center location and allocation problem in a closed loop supply chain for the beer industry, in which the objective is to minimize total costs and transportation pollution. Uncertainties in the form of randomness and fuzziness are jointly handled in this paper to ensure a more practical problem solution, for which returned bottle sand unusable bottles are considered fuzzy random variables. A heuristic algorithm based on priority-based global-local-neighbor particle swarm optimization (pb-glnPSO) is applied to ensure reliable solutions for this NP-hard problem. A case study on a beer operation company is conducted to illustrate the application of the proposed model and demonstrate the priority-based global-local-neighbor particle swarm optimization.

In recent years, cerium dioxide (CeO2) has attracted considerable attention owing to its remarkable performance in various applications, including photocatalysis, fuel cells, and catalysis. This study explores the effect of nickel (Ni) doping on the structural, thermal, and chemical properties of CeO2 nanorods, particularly focusing on oxygen vacancy-related phenomena. Utilizing X-ray powder diffraction (XRD), alterations in crystal structure and peak shifts were observed, indicating successful Ni doping and the formation of Ni2O3 at higher doping levels, likely due to non-equilibrium reactions. Thermal gravimetric analysis (TGA) revealed changes in oxygen release mechanisms, with increasing Ni doping resulting in the release of lattice oxygen at lower temperatures. Raman spectroscopy corroborated these findings by identifying characteristic peaks associated with oxygen vacancies, facilitating the assessment of Ni doping levels. Overall, this study underscores the substantial impact of Ni doping on CeO2 nanorods, shedding light on tailored catalytic applications through modulation of oxygen vacancies while preserving the nanorod morphology.

We investigate and discuss in detail the structure of the restricted singular value decomposition for a tensor triplet under t-product (T-RSVD). The algorithm is provided with a numerical example illustrating the main result. For applications, we consider color image watermarking processing with T-RSVD.

In agriculture, soil-borne fungal pathogens, especially Fusarium oxysporum strains, are posing a serious threat to efforts to achieve global food security. In the search for safer agrochemicals, silica nanoparticles (SiO2NPs) have recently been proposed as a new tool to alleviate pathogen damage including Fusarium wilt. Hollow mesoporous silica nanoparticles (HMSNs), a unique class of SiO2NPs, have been widely accepted as a desired pesticide carrier. However, their role in enhancing the disease resistance and the specific mechanism remain unknown. In this study, three sizes of HMSNs (19, 96 and 406 nm as HMSNs–19, HMSNs–96 and HMSNs–406, respectively) were synthesized and characterized to determine their effects on seed germination, seedling growth, and Fusarium oxysporum f. sp. phaseolus (FOP) suppression in cowpea roots by foliar spray using phenotypes, fresh biomass and disease progression as indicators. The results revealed that three HMSNs exhibited no adverse impacts on seed germination and tended to improve plant growth. Also, they exert their FOP suppression with a size- and concentration-dependent manner. HMSNs–406 possessed the best control effect at a concentration of 1000 mg/L showing an upto 40.00% decline in the disease severity. The Si(OH)4 control was also effective on FOP suppression at a lower concentration of 100 mg/L, whereas its higher concentrations exhibited obviously adverse impacts on FOP control, seed germination and plant growth. Moreover, we conformed that HMSNs posed their Fusarium wilt suppression in cowpea plant by activating SA (salicylic acid)-dependent SAR (systemic acquired resistance) responses rather than directly suppressing FOP. A higher level of SA content and elevated expression of its maker genes of PR-1 and PR-5 in HMSNs–406 treated cowpea roots provided substantial evidences of this mode of action. Other resistance-related genes, as well as defense-responsive enzymes, were also involved in the HMSNs-activated SAR pathway. Overall, for the first time, our results extended a new role of HMSNs as a potent elicitor to serve as a versatile alternative for plant disease protection of low cost, highly efficiency and sustainability.

Advanced lithography requires highly sensitive photoresists to improve lithographic efficiency, and it is critical yet challenging to develop high-sensitivity photoresists and imaging strategies. Here, we report a novel strategy for ultra-high sensitivity using hexafluoroisopropanol (HFIP)-containing fluoropolymer photoresists. The incorporation of HFIP, with its strong electrophilic property and electron-withdrawing effect of the fluorine atoms, significantly increases the acidity of the photoresist after exposure, enabling imaging without conventional photoacid generators (PAGs). The HFIP-containing photoresist has been evaluated by electron beam lithography to achieve a trench of ~40 nm at an extremely low dose of 3 μC/cm2, which shows sensitivity enhancement by ~10 times to the commercial PAGs involved system, revealing its high-sensitivity and high-resolution features. Our results demonstrate a new type of PAGs and a novel approach to higher-performance imaging beyond conventional photoresist performance tuning.

Despite the partial disclosure of driving scenario knowledge graphs, they still fail to meet the comprehensive needs of intelligent connected vehicles for driving knowledge. Current issues include the high complexity of pattern layer construction, insufficient accuracy of information extraction and fusion, and limited performance of knowledge reasoning models. To address these challenges, a hybrid knowledge graph method was adopted in the construction of the Driving Scenario Knowledge Graph (DSKG). Firstly, core concepts in the field were systematically sorted and classified, laying the foundation for the construction of a multi-level classified knowledge graph top-level ontology. Subsequently, by deeply exploring and analyzing the Traffic Genome data, 34 entities and 51 relations were extracted and integrated with the ontology layer, achieving the expansion and updating of the knowledge graph. Then, in terms of knowledge reasoning models, an analysis of the training results of the TransE, Complex, Distmult, and Rotate models in the entity linking prediction task of DSKG revealed that the Distmult model performed the best in metrics such as hit rate, making it more suitable for inference in DSKG. Finally, a standardized and widely applicable Driving Scenario Knowledge Graph was proposed. The DSKG and related materials have been publicly released for use by industry and academia.

Osteoporosis (OP), a prevalent skeletal disorder characterized by compromised bone strength and increased susceptibility to fractures, poses a significant public health concern. This review aims to provide a comprehensive analysis of the current state of research in the field, focusing on the application of proteomic techniques to elucidate diagnostic markers and therapeutic targets for OP. The integration of cutting-edge proteomic technologies has enabled the identification and quantification of proteins associated with bone metabolism, leading to a deeper understanding of the molecular mechanisms underlying OP. In this review, we systematically examine recent advancements in proteomic studies related to OP, emphasizing the identification of potential biomarkers for OP diagnosis and the discovery of novel therapeutic targets. Additionally, we discuss the challenges and future directions in the field, highlighting the potential impact of proteomic research in transforming the landscape of OP diagnosis and treatment.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.