MCrAlX (M: Ni or Co or both, X: minor elements) coatings have been widely used to protect hot components in gas turbines against oxidation and hot corrosion at high temperatures. Understanding the influence of the X-elements on oxidation behaviour is important in the design of durable MCrAlX coatings. In this study, NiCoCrAlX coatings doped with Y+Ru and Ce, respectively, were deposited on Inconel-792 substrate by HVOF. The samples were subjected to isothermal oxidation test in laboratory air at 9000, 1000, 1100 ºC and cyclic oxidation test between 100 ºC and 1100 ºC with 1 hour dwell time at 1100 ºC. It was observed that the coating with Ce shows a much higher oxidation rate than the coating with Y+Ru under both isothermal and cyclic oxidation tests. Besides, β-depletion due to interdiffusion between coating and substrate was significantly lower with Ru addition. Simulations results using both a moving phase boundary model and an established oxidation-diffusion model show that Ru stabilize β grains which reduces β-depletion of coating due to substrate interdiffusion. This paper presents a comprehensive study of the influence of Ce and Ru on oxidation behaviour including investigation of the microstructure evolution influenced by oxidation time at coating surface and coating-substrate interface combining experiment and simulation results.

Based on previous research results, we propose a new preprocessing HSS iteration method (PHSS) for the generalized Lyapunov equation. At the same time, the corresponding inexact PHSS algorithm (IPHSS) is given from the angle of application. All the new methods presented in this paper have given the corresponding convergence proof. The numerical experiments are carried out to compare the new method with the existing methods, and the improvement effect is obvious. The feasibility and effectiveness of the proposed method are proved from two aspects of theory and calculation.

In the early stage of new vehicle development, the requirements of maximum performance of the air conditioning (AC) system are obtained through Amesim software simulation, but the calibration control of the AC system is usually carried out in the prototype-build vehicle test stage, and the test time is spanned up to 10 months after spring (autumn), summer and winter, of which up to 2 months are for environment chamber tests. Due to the long calibration cycle of AC control in the road test, which seriously affects the vehicle launch time, virtual calibration technology of air conditioning system is developed to shorten the calibration cycle of AC systems and ensure the quality of vehicles. In the project development stage, the calibration control of the vehicle AC system can be realized to carry out the functional test of the AC system in advance. In that, the grade of maturity for the AC system control can be improved, the on-road calibration test cycle can be shortened, and the development cost can be saved.

Fabrication of durable materials with excellent oil adsorption capacity and separation performance for the treatment of oily wastewater is meaningful based on smart responsiveness. Herein, a solvent-responsive melamine sponge (MS) was developed via silanization followed by the in-situ growth of zeolitic imidazolate framework-8 (ZIF-8). Detailed characterization of the resultant composite MS was conducted using scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR). The multiscale hierarchical MS substrate exhibited highly hydrophobic property in the pH range of 1-11, along with a satisfactory adsorption capacity in the range of 65.4-134.2 g/g for different oils. The modified surface transformed from superhydrophobicity/superlipophilicity to superhydrophilicity/underwater superoleophobicity upon ethanol wetting, reverting to its original superhydrophobic state upon drying. The separation flux of the MS substrate was above 1.5×104L/m2h for both oil and water removal, along with the separation efficiency more than 98.7%. No obvious changes of the separation performance after 50 successive immiscible oil/water separation indicated the excellent durability and robustness of the anchored ZIF-8 nanoparticles on the surface of modified MS substrate. More importantly, oil-in-water emulsion separation was successfully carried out via the ZIF-8 MS composite with a high separation efficiency over 99.1%. The developed smart sponge with high oil absorption capacity, excellent chemical stability and fire resistance exhibited a wide range of potential practical applications in the convenient treatment of oily wastewater.

Ionic gel electrolyte retains the characteristics of non-volatilization, non-flammability and outstanding electrochemical stability of ionic liquid, and shows good electrochemical performance combined with the excellent characteristics of different matrix materials, which is considered to be the best choice to achieve the high energy density and safety at the same time. In this paper, a flexible and self-healing ionic gel electrolyte is prepared by solvent-assisted method based on a zteric ion (ZI) copolymer. Abundant hydrogen bonds and synergistic interaction of ions in the electrolyte system endowed it with wonderful self-healing ability. The ionic conductivity of 9.06×10-4 S cm-1 at room temperature was achieved. Besides, the tLi+ was also increased to 0.312. The self-healing function of the ionic gel electrolyte ensured the long-term tolerance of the SHIGE. The capacity retention rate of the Li//LiFePO4 battery is 96% after 155 cycles at 0.1 C at 60 oC. This polymer electrolyte is expected to solve the problem of increasing polarization，which is caused by the low lithium ions migration number in ionic liquid electrolyte. And ultimately, it gives rise to a good rate performance.

The greatly diversified flowering plants (angiosperms) are the dominating and defining group in the current earth ecosystem. However, from which group by what way the flowers, especially their gynoecia (key characteristics of angiosperms), are derived have been the questions in botany unanswered over centuries. Such an embarrassing situation can be attributed to the lack of plants with partially enclosed ovules, which are supposed to be a post between gymnosperms and angi-osperms. Here we report a fossil plant that has an apparent coniferous vegetative and reproduc-tive morphologies but has a single seed partially wrapped by the subtending bract. Such a mor-phology suggests that the carpels in angiosperms may be equivalent to bracts enclosing their axil-lary seed(s). Such a non-traditional interpretation of the homology of angiosperm carpels is com-patible with various new progresses made in botany and is in line with Tomlinson’s recent hy-pothesis. Together with other fossil evidence reported recently, it appears that gynoecia in angio-sperms are derived in multiple ways.

Spacecraft recovery technology is crucial in the field of aerospace, in which the parachute plays a key role in slowing down the descent speed of the spacecraft and realizing a smooth landing. In order to construct a dynamically adjustable parachute deployment strategy, it is necessary to measure the parachute dynamic load accurately in real time. However, the existing sensor measurement scheme is difficult to meet the measurement requirements due to its large structure and complex wiring. In order to meet the current demand for real-time measurement of parachute cords dynamic load, a miniature measuring instrument is designed.According to the function and technical requirements of the miniature measuring instrument, the hardware modules of the acquisition system are selected and designed, and the integration debugging and performance optimization of the microcontroller module, A/D sampling module, signal acquisition circuit and power supply module are carried out. The software of the parachute cords tension acquisition system based on the miniature measuring instrument is developed. The elastomer is modeled by using SolidWorks and statically analyzed by using AnsysWorkbench finite element analysis software. Then the final structure of the elastomer and the pasting position of the strain gage are determined through the results analysis as well as experimental verification. The hardware module of the signal acquisition system for the miniature measuring instrument is then encapsulated. The force value of the miniature measuring instrument is calibrated and tested many times by using the microcomputer-controlled electronic universal testing machine. The experimental results show that the designed miniature measuring instrument has accurate data, strong stability and good real-time performance, which meets the demand for real-time accurate measurement of miniature measuring instrument, and can provide reliable data for parachute cords parameter validation and stepless unfolding design.

As traditional supply chains face increasingly severe environmental issues and countries promote green development and sustainable development policy concepts, cultivating green supply chain operation models is gradually being highly valued by current governments and enterprises. Generally speaking, the production of green products incurs higher additional costs and thus their total production costs also increase. In this work, the product green level is related to the random demand. Under the green supply chain buy-back contract with the green product R&D cost sharing between the manufacturer and the retailer, both the product green level and the order quantity need to be decided to maximize the channel profit. In order to coordinate the green supply chain, the manufacturer needs to share both the risk of good salvage and the green product R&D cost with the retailer. We find that both the wholesale price and buy-back price increase in the manufacturer’s proposition of the green product R&D cost, but decrease in emission reduction efficiency coefficient or carbon trading price. In addition, the product green level, the optimal order quantity and the channel profit increase in emission reduction efficiency coefficient, but decrease in the R&D cost coefficient of the product green level. Interestingly, we find that if the carbon trading price is low, the manufacturer will set a low product green level and the product carbon emission trading is a cost for the supply chain. The increment of the carbon trading price leads to a higher cost such that the channel profit is decreased. However, if the carbon trading price is high, the manufacturer will set a high product green level and the product carbon emission trading is a revenue for the supply chain. The increment of the carbon trading price leads to a higher revenue such that the channel profit is increased.

Rotary tillage is a main management tillage practices and widely applied in the North China Plain. However, the long term rotary tillage (depth of 20 cm) results in soil compaction and plow pan formation, which reduces water use efficiency and nutrient uptake, and then impedes the yield increase. In this study, a 3-year field experiment was conducted to investigate the influence of different depths of tillage on soil bulk density, field capacity, water use, photosynthetic rate, nutrients and maize yields in the North China Plain. Three depths of tillage (D20, depth of 20 cm; D25, depth of 25 cm; D30, depth of 30 cm) were assessed. D25 and D30 significantly reduced soil bulk density and improved field capacity in 10-20 and 20-30 cm soil layer, compared to D20. Soil water consumption for D25 was significantly higher 10.12% and 6.61% than that for D20 and D30, respectively. Photosynthetic rate for D25 significantly improved than that for D20 and D30. Total nitrogen in 0-20cm soil layer decreased with the depths of tillage. The maize yields for D25 significantly increased by 20.92% and 21.56% compared to that for D20 and D30, respectively. Structural equation models showed that the total effects of tillage, total nitrogen, photosynthesis and soil water consumption on yields were 0.019, -0.628, 0.121, and 0.895 (path coefficients λ), respectively. The results demonstrated that D25 could improve maize yields, water use efficiency, photosynthetic rate by improving soil water consumption. Depth of 25 cm is optimal tillage practice for the maize production in the North China Plain.

Most machine learning and deep learning algorithms can only use low-dimensional data as input, but the data that must be processed in practical applications is diverse and irregular. There are two main problems with big dynamic data. (1) The size of the embedding table grows linearly with the vocabulary size, resulting in massive memory consumption. (2) For different newly added vocabularies. To solve these two problems, this paper proposes a novel embedding algorithm that can learn attribute associations with entities based on deep and hash algorithms. Taking movie data as an example, the encoding method and the specific flow of the algorithm are presented in detail, and the effect of dynamic reuse of data models is realized. Compared with the four existing embedding algorithms which can fuse entity attribute information, the deep hash embedding algorithm proposed in this paper has obvious optimization of time and space complexity.

In this paper, we shall introduce the interval-valued spatial error model. Based on the idea of least square method of single-valued case, we give the parameter estimator for interval-valued spatial error model. The theoretical properties of the proposed estimator are proved. Finally, we give the numerical analysis and a real example.

Chondrocytes maintain the normal morphological structure and physiological function of articular cartilage. However, the increased expression of inflammatory mediators and matrix-degrading enzymes in chondrocytes can promote ECM degradation, consequently disrupting the physiological function of articular cartilage and ultimately leading to the onset of osteoarthritis (OA). Usnic acid (UA), an extract derived from plants, possesses multiple bioactive properties including anti-inflammatory and antioxidant effects. Hence, this study aims to explore the molecular mechanisms underlying its protective effects in an in vitro simulated model of OA in rat chondrocytes. In vivo experiments encompassed three groups: Control, Model, and Usnic acid (50 mg/kg), with sample extraction following 12 weeks of administration. Pathological alterations in articular cartilage were evaluated using Safranin O-fast green staining. Immunohistochemistry (ICH) analysis was employed to assess the expression of matrix degradation-related markers. The levels of serum cytokines were quantified via ELISA assays. In this study, primary rat chondrocytes were employed as the experimental subject. After a 24-hour treatment period, culture supernatants, total RNA, total protein, and nuclear protein were extracted from the different chondrocyte groups. ELISA and qPCR methods were used to measure levels of IL-6, TNF-α, and PGE2. WB and qPCR were employed to assess levels of p65, p-p65, IκBα, p-IκBα, Nrf2, HO-1, NQO1 ADAMTS-4, MMP-1, MMP-3, MMP-13, INOS, COX-2, and COL2A1. IF analysis was performed to examine Nrf2, p-p65 and COL2A1. Results: (1) In vivo, intraperitoneal injection of usnic acid (50mg/kg) can alleviate pathological changes in articular cartilage and the levels of inflammatory and oxidative-related matrix in the serum. (2) UA reduced the level of inflammatory cytokines in IL-1β-induced chondrocytes supernatant. (3) UA can produce anti-inflammatory and antioxidant effects and inhibit chondrocytes matrix degradation through the Nrf2 and NF-κB pathways. (3) The mechanism by which UA exerts a protective role in chondrocytes is mediated by Nrf2 Conclusion: UA inhibits the expression of chondrocyte matrix degradation-related components through Nrf2 mediated Nrf2 pathway and NF-κB pathway, promotes the production of protective substances, and ultimately exerts a protective effect on chondrocytes.

Noisy data is always encountered in real applications, such as bioinformatics, neuroimage and remote sensing. Existing methods mainly consider linear or generalized linear errors-in-variables regression, while relatively little attention is paid for the multivariate response case, and how to evaluate the estimation performance under perturbed covariates is still an open question. In this paper, we consider the information-theoretic limitations of estimating a low-rank matrix in the multi-response errors-in-variables regression model. By application of the information theory and statistical techniques on concentration inequalities, the minimax lower bound is provided in terms of the squared Frobenius loss, which recaptures the rate provided under the clean covariate assumption in previous literatures. Hence our result further indicates that though under the more realistic errors-in-variables situation, no more samples are required so as to achieve a rate-optimal estimation.

The aim of this study was to examine and understand the physiological and biochemical components of the blood and vitreous humor of goldfish (Carassius auratus). Blood was drawn from the arterial (static) line and vitreous humour was extracted using a syringe from healthy goldfish. An automatic haematology analyzer was used to detect 17 physiological indicators, including white blood cells and red blood cells. At the same time, 20 biochemical indexes, including albumin, calcium, and glutamic pyruvic transaminase, were found in the automatic biochemical analyzer. Experiments were also conducted on the effect of blood and vitreous fluid collection on the subsequent survival rate of the celestial goldfish. The findings demonstrated that there were values for 17 physiological indicators in the blood of the goldfish, including red blood cells (2.19 × 1012), white blood cells (62.21 × 109), hemoglobin (138.25g/L), and no eosinophils or basophils. However, no data for 17 physiological indications of vitreous humor were discovered. The quantities of total protein, glutamic oxaloacetic transaminase, and potassium in the vitreous humor were substantially lower than those in the serum (P < 0.01) according to the results of 20 biochemical indexes in the serum and vitreous humor of goldfish. Alkaline phosphatase, chlorine, and creatinine between vitreous humor and serum did not differ significantly(P > 0.05). The levels of glutamic pyruvic transaminase and γ-glutamyl transpeptide in vitreous humor were significantly higher than those in serum (P < 0.01). This experiment provides basic datas for the healthy culture of goldfish and the perfection of hematology in goldfish, and the results will be convenient for the further study of development and formation of celestial eye traits.

The activated carbons (ACs) derived from okara powder waste with high surface areas were modified with ammonia aqueous solution impregnation in an autoclave to enhance their CO2 adsorption properties toward CO2. The impregnated ACs were characterized in which surface chemical composition and properties of the ACs were analyzed by SEM-EDS, FTIR. Activated carbons were functionalized with ammonia aqueous solution (25%) through a hydrothermal process within 24; 48, and 72 hours. The adsorption performance of CO2 onto carbon samples was experimentally evaluated through a breakthrough adsorption experimental setup at room temperature. FTIR spectra confirm the N-containing in N-modified activated carbons and the presence of the –C = O stretch and N-H groups. CO2 uptakes of N-modified activated carbons are 0.24; 1.47; and 1.20 mmol/g, which are relatively comparable with those of activated carbons studied in in the literature.

Metabolites present in the hemolymph of honey bees play a crucial role in modulating the metamorphic process within the species. However, the precise alterations in metabolite composition, along with the associated variances and regulatory pathways implicated during the larvae-to-pupae metamorphosis of honey bees, remain incompletely elucidated. In this investigation, we gathered hemolymph samples from honey bee larvae at three distinct physiological stages-feeding, prepupal, and pupae and subjected them to metabolite analysis utilizing the liquid chromatography-mass spectrometry (LC-MS) technique. Employing principal component analysis (PCA) and partial least squares-discriminant analysis (PLS-DA), we identified significant differential metabolites and conducted a metabolic pathway analysis on those differentially up-regulated during the prepupal and pupae stages. Notably, metabolites up-regulated in the hemolymph of prepupal stage larvae primarily governed glucose metabolism and fat digestion and absorption, while those in pupae stage larvae were involved in regulating chitin and lipopolysaccharide precursor formation, as well as the biosynthesis of phenylalanine, tyrosine, and tryptophan. These findings bear significant implications for advancing our comprehension of the metamorphic processes in honey bees.

At present paper, we aim to study the long-time behavior of a stochastic semi-linear degenerate parabolic equation on bounded or unbounded domain and driven by a nonlinear noise and defined. Since the theory of pathwise random dynamical systems can not be applied directly to the equation with nonlinear noise, first, we establish the existence of weak pullback mean random attractors for the equation by applying the theory of mean-square random dynamical systems; then, we prove the existence of (pathwise) pullback random attractors for the Wong-Zakai approximate system of the equation. In addition, we establish the upper semicontinuity of pullback random attractors for the Wong-Zakai approximate system of the equation under consideration driven by a linear multiplicative noise.

The present study propose an innovative turn-boring operation method and focuses on finding optimal turn-boring process parameters for Ti-6Al-4V by considering multiple performance characteristics using Taguchi orthogonal array with the grey relational analysis, the effect of machining variables such as, feed rate, depth of cut and cutting speed are optimized with considerations of multiple performance characteristics namely surface roughness, roundness error, material removal rate and power consumption the optimal values were found out from the Grey relational grade. The result of the Analysis of Variances (ANOVA) is shown that the most significant factor is cutting speed, followed by feed rate, radial depth of cut. Finally, confirmation tests were carried out to make a comparison between the experimental results. Experimental results have shown that machining performance in the turn-boring process can be improved effectively through this approach.

In 2011-2012, Northern Vietnam suffered its first large scale hand foot and mouth disease (HFMD) epidemic. Two sets of official guidelines were issued during the outbreak to handle the HFMD crisis. The city of Hai Phong was therefore used as a model to analyze the impact of the guidelines release. 9621 HFMD cases were reported in Hai Phong city from April 2011 to December 2012. Three distinct waves of HFMD occurred. Enterovirus A71 and Coxackievirus A16 were successively associated to the epidemics. Two periods, before and after guidelines realease, could be distinguished which were characterized by different patient patterns Time to admission and severity changed notably. Guideline publication help the health system refocusing on the 0.5-3 years age group with highest incidence of the disease. The three waves showed different special distribution but main routes of infection were rivers and local secondary roads most likely through local trade and occupational movements of people.

Aims: To assess the occurrence of Chemotherapy-induced nausea and vomiting (CINV) after standard antiemetic therapy in the acute (24 h post-chemotherapy) and delayed (2–5 days post-chemotherapy) phases, as well as to identify risk factors for CINV in the acute and delayed phases. Methods: This prospective longitudinal and observational study analyzed the data of 400 breast cancer patients scheduled for chemotherapy over two cycles in two hospitals. The self-report survey was developed to assess the occurrence of CINV and their associated factors. CINV was evaluated with a Multinational Association of Supportive Care in Cancer Antiemetic Tool (MAT) on days 2 and 6 of chemotherapy. The incidence of acute and delayed CINV were presented by frequency and percentage. Generalized equation estimates (GEE) was used to identify risk factors of acute and delayed CINV. Results: There were 400 evaluable patients with complete Round 1 data, 334 for Round 2 data. Among 400 patients, 29.8% and 23.5% experienced acute and delayed CINV, respectively. Risk factors associated with for acute CINV were pain/insomnia, history of CINV, history of motion sickness (MS), and highly emetogenic chemotherapy regimen, while history of MS, CINV history, number of completed chemotherapy cycle number < 3, and the incidence of acute CINV were risk factors of delayed CINV (all p < 0.05). Conclusions: The findings may help nurses working for Chinese population in identifying patients at risk for CINV and in planning effective program to reduce the occurrence of CINV.

This paper proposes a novel hybrid control strategy for quadrotor unmanned aerial vehicles (UAVs) based on bio-inspired neural dynamics. This strategy addresses the velocity jump issue prevalent in traditional backstepping control and the control signal chattering problem common in traditional sliding mode control. The control system comprises an outer-loop bio-inspired backstepping controller and an inner-loop bio-inspired sliding mode controller, ensuring smooth trajectory tracking even in the presence of external disturbances. The stability of the quadrotor UAV control system is rigorously analyzed using Lyapunov stability theory. Extensive comparative simulation experiments are conducted to assess the robustness and effectiveness of the control system. Results demonstrate superior trajectory tracking performance of the proposed control system compared to other control systems for quadrotor UAVs.

This paper presents a comprehensive cost-benefit analysis of producing alternative phosphorus (P) fertilizers from recycled water treatment residuals (Fe-WTR) and cowshed effluents, under the umbrella of circular economy approach. Fe-WTR is compared to a synthetic adsorbent, layered double hydroxide (LDH). Dairy wastewater is used as a P source for both adsorbents. The cost of 1 ton P-Fe-WTR sums up to 329 Euro. In contrast, the use of synthetic adsorbents (P-LDH) incurs significantly higher costs, amounting to 3329 Euros per ton, underscoring the economic advantage of utilizing waste-derived materials. Adopting Fe-WTR fertilizer not only offers substantial cost savings by avoiding landfill fees (40-150 Euros per ton) and wastewater discharge fines (500 Euros per ton) but also reduces environmental impacts. This sustainable method mitigates eutrophication and pollution, presenting a dual benefit of cost-effectiveness and environmental protection. Although our results are based on a specific case study, they reflect the potential value of extending the circular economic approach to P production worldwide: Recycling P from waste streams can be economically viable and environmentally preferable at large, aligning with global sustainability goals and demonstrating the practicality of circular economy principles in environmental management.

The human serotonin transporter (hSERT) terminates neurotransmission by removing serotonin from the synaptic cleft, which is an essential process plays an important role in depression. In addition to substrate serotonin, hSERT is also the target of drugs of abuse like cocaine and clinically used antidepressants such as escitalopram and paroxetine. To date, few studies attempt to investigate the unbinding mechanism underlying the orthosteric and allosteric modulation of hSERT. The high-resolution X-ray structure of hSERT resolved recently enables us to theoretically study the unbinding of the above four ligands against the S1 or S2 site of hSERT, by means of molecular docking, molecular dynamics (MD) and potential of mean force (PMF) simulations. We proved that for either the S1 or S2 site, the other three ligands (cocaine, escitalopram and paroxetine) are much more favorable than the original substrate serotonin, whether in kinetics along the unbinding pathways or in thermodynamics at the equilibrium states. Furthermore, the S1 site is much more favorable than the S2 site, for each ligand. Interestingly, inspection revealed that there are ~ 3Å lengths between the allosteric site of serotonin and cocaine, and an unseen un-binding pathway for escitalopram at the S1 site except for verification of the broadest trail.

This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

Directed energy deposition (DED) is an efficient method to fabricate functionally graded materials (FGMs) with gradient composition and complex structures, allowing for local tailoring of properties instead of the costly need for extraneous welds and joints. In this study, a FGM from stainless steel to Inconel alloy was successfully fabricated using the powder-based laser DED. A very refined grain structure has been observed in at the composition with 75 wt.% Inconel alloy content, which also exhibits the highest (entropy). For the first time, the post heat treatments, microstructure and aging precipitation behaviors of FGMs were systematically studied via experimental characterization and computation, to elucidate their effects on the gradient smoothing and mechanical properties. The diffusion and segregation of Ni, Nb and Ti elements underly the transformation mechanism between Laves, δ, γ’ and γ’’ phases during precipitation. Homogenization on FGMs not only eliminates the heterogeneity inherited from the AM process, but also provides a practical way to smoothen the gradient on composition and microstructure for the eventual good gradient properties. It has a direct influence on the following precipitation behaviors in the FGM, which highly relies on the diffusion degree of the elements in the matrix and grain boundaries. The high-throughput thermodynamic modeling and kinetic modeling were exploited to evaluate the experimental microstructure and address computational uncertainty using different thermodynamic conditions and databases, which enables an accelerated design through local tailoring of process-structure-property relationships to develop new functional materials.

Drug-target affinity (DTA) prediction is crucial for understanding molecular interactions and aiding drug discovery and development. While various computational methods have been proposed for DTA prediction, their predictive accuracy remains limited, failing to delve into the structural nuances of interactions. With increasingly accurate and accessible structure prediction of targets, we developed a novel deep learning model, named S2DTA, to accurately predict DTA by fusing sequence and structural knowledge of drugs, targets, and pockets using heterogeneous models based on graph and semantic networks. Experimental findings underscored that complex feature representations imparted negligible enhancements to the model’s performance. However, the integration of heterogeneous models demonstrably bolstered predictive accuracy. In comparison to three state-of-the-art methodologies, the supremacy of S2DTA became strikingly apparent. It showcased a noteworthy 25.2% reduction in Mean Absolute Error (MAE) and an impressive 20.1% decrease in Root Mean Square Error (RMSE). Furthermore, S2DTA exhibited substantial advancements in other pivotal metrics, including Pearson Correlation Coefficient (PCC), Spearman, Concordance Index (CI), and R2. These metrics experienced remarkable increments of at least 19.6%, 17.5%, 8.1%, and a remarkable 49.4%, respectively. Finally, we conducted interpretability analysis on the effectiveness of S2DTA by bidirectional self-attention mechanism, fully proving that S2DTA is a valuable and accurate tool for predicting DTA. For further exploration, the source data and code repository can be accessed at https://github.com/dldxzx/S2DTA.

Cordyceps sinensis is one rare medicinal fungus produced in the Qinghai-Tibetan Plateau. Its quality and price varies hugely with different habitat, and its numerous substitutes have sprung up in functional food markets. This paper aims to discriminate the geographic origin of wild C. sinensis and its substitutes via the element analyzer-isotope ratio mass spectrometry and gas chromatography-isotope ratio mass spectrometry. The δ¹³C values of major fatty acids in the lipids of Cordyceps sinensis are characterized unanimously by the variation relation C_18:0 ﹤ C_18:2 ≈ C_16:0 ﹤ C_18:1; while their fluctuation intervals are notably different between those of neutral and polar lipids. The comparative analysis of the δ¹³C ratios of major fatty acids in lipids of Cordyceps sinensis suggests that the δ¹³C patterns may be sensitive potential indicators to discriminate its geographical origin. The δ¹³C values of individual major fatty acids of lipids from the cultivated stromata of Cordyceps militaris (SCM), the fermented mycelia of Hirsurella sinensis (FMH) and Paecilomyces epiali (FMP) range from −31.2‰ to −29.7‰, −16.9‰ to −14.3‰, and −26.5‰ to −23.9‰, respectively. Their δ¹³C pattern of individual major fatty acids may be used as a potential indicator to discriminate the products of natural C. sinensis and its substitutes.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

An active power dispatch method for a microgrid (MG) with multi-type loads, renewable energy sources (RESs) and distributed energy storage devices (DESDs) is the focus of this paper. The MG operates in a grid-connected model, and distributed power sources contribute to the service for load demands. The outputs of multiple DESDs are controlled to optimize the active power dispatch. Our goal with optimization is to reduce the economic cost under time-of-use (TOU) price, and to adjust the excessively high or low load rate of distributed transformers (DTs) caused by the peak-valley demand and load uncertainties. To simulate a practical environment, the stochastic characteristics of multi-type loads are formulated. The transition matrix of system state is provided. Then, a finite-horizon Markov decision process (FHMDP) model is established to describe the dispatch optimization problem. A learning-based technique is adopted to search the optimal joint control policy of multiple DESDs. Finally, simulation experiments are performed to validate the effectiveness of the proposed method, and the fuzzification analysis of the method is presented.

With the increasing of copper consumption, the in-use stock of copper tends to increase. This paper used the “average use life method” to quantify the amount of copper in-use stock, and calculated the average age of in-use stock. It was indicated that the total in-use stock had an overall smooth trends, and reached its peak in 2007 was about 68.9 Mt (million tons), in addition, in-use stock per capita reached its peak ,234 kg/capita in 2001. The results demonstrated that during the period 1992-2002, the average age of copper in-use stock was continually decreased, but gradually increased since the year 2003. The fixed assets depreciation method used in this paper is applied to analyze depreciated copper in-use stock, and to analyze the relationship with economic indicator (GDP). It is demonstrated that it was inconsistent with the theory of Environmental Kuznets Curve (EKC) before 2000, this might be the demand for copper in the service sector is greater than the reduced strength of alternatives. Finally, scenario analysis of future copper in-use stock and depreciated copper in-use stock per capita in the U.S. were presented. The corresponding average age of the in-use stock will have a slight rise in the next decade.

Carbonaceous material (CM) is common in meta-sediments and is generally interpreted to be intimately associated with gold mineralization. For the Bumo deposit in Hainan Province, South China, CM is mainly hosted by greenschist facies- to amphibolite-facies metamophic rocks of the Paleo- to Mesoproterozoic Baoban Group and by auriferous veins and is used as an important gold prospecting indicator. However, the genesis of CM and the relationship with gold mineralization are still not clear. Field work and thin section observation indicates that two types of CM occur, i.e., layered and veinlet. Layered CM, up to meters thick, prevails in the deposit. More importantly, Au-bearing sulfides are commonly distributed along the boundary between the quartz veins and layered CM. In contrast, veinlet CM, co-precipitated with gold and sulfides, has the thickness of micro- to centi- meters, and these thin veins occur in quartz veins and hydrothermally altered rocks. Scanning Electron Microscope (SEM) analysis indicates that layered CM has a stringy shape and laminate structure, while veinlet CM occurs as isometric particles. Raman carbonaceous material geothermometer indicates that layered CM with high maturity is formed at elevated temperatures of 400 – 550°C, consistent with X-ray diffraction (XRD) analysis. In contrast, veinlet CM with low maturity is formed at 200 – 350°C, generally consistent with gold mineralization. In addition, layered CM has δ13C values ranging from -30 to -20%, demonstrating a biogenic origin. Consequently, it is interpreted that layered CM is formed by a pre-ore metamorphic event during Caledonian, and its reducing nature promotes gold precipitation via destabilization of aqueous Au bisulfide complexes or facilitating sulfidation. Veinlet CM is hydrothermal origin, and its precipitation modified the chemical conditions of ore fluids, leading to the destabilization of Au complexes and thus favorable for mineralization.

The research on the distribution of rural buildings is one of the fundamental works of urban-rural development in Vietnam. Adopting Mask R-CNN deep learning framework and collecting sub-meter remote sensing images, this research used a remote sensing interpretation model of rural buildings trained based on East Asian characteristics of rural buildings and successfully recognized about 2.87 million rural buildings in 34 Vietnamese provincial administrative districts with a total area of rural buildings of 2,492 million square meters. The reliability of the identification results was verified by manual detection and quantitative statistics, and a multi-scale database of rural buildings in Vietnam based on individual rural buildings was created. Based on the database, this paper analyzes the distribution characteristics of rural buildings and summarizes characteristics of rural buildings distribution at the country, regional, and provincial scales. The identification results lay the foundation for the next study of urban-rural relations in Southeast Asia and the construction of a basic database on villages.

A new longitudinal flow heat dissipation theory for cylindrical batteries is proposed in order to increase the energy density and uniform temperature performance of cylindrical lithium-ion battery packs while also shrinking their size by roughly 10%. First, a genetic algorithm is used to identify the single cell's thermal properties. Based on this, modeling and simulation are used to examine the thermal properties of the longitudinal flow-cooled battery pack. It is found that the best coolant flow scheme has one inlet and one outlet from the end face, taking into account the cooling effect of the battery pack and engineering viability. Lastly, Thermal Dummy Cells (TDC) is used to conduct a validation test of the liquid cooling strategy. Additionally, the simulation and test results demonstrated that the liquid cooling solution can keep the battery pack's maximum temperature rise under the static conditions of a continuous, high-current discharge at a rate of 3C to 20 °C and under the dynamic conditions of the New European Driving Cycle (NEDC) to 2 °C. In applications where the space requirements for the battery pack are quite severe, the longitudinal flow cooling method has some advantages.

Objective: This study aimed to demonstrate the availability of portable devices for nasal FeNO measurement, which could replace exhaled NO measurement based on the continuous aspiration of multiple flow measurement systems. Methods: A descriptive cross-sectional study. The healthy subjects without rhinosinusis disorders (control group) and those with diagnosed allergic rhinitis (AR group) were enrolled in the study. They underwent nasal and bronchial FeNO measurements by both fixed flow NObreath® connected to nasal mask and multiple flows HypAir FeNO®. Results: A total of 153 people were recruited including 63 healthy subjects and 90 subjects with AR. There were no statistically significant differences in anthropometric characteristics between the two groups (P > 0.05). There were a significant increase in FeNO values in the AR group compared to the control group; concentrations of nasal and bronchial FeNO mearsured by NObreath® were 76.0 ± 50.7 ppb (vs 36.0 ± 28.1 ppb, P < 0.01) and 32.3 ± 15.4 ppb (vs 9.2 ± 5.6 ppb, P < 0.001), and those mearsured by NObreath® Hypair FeNO® were 1796.9 ± 523.3 ppb (vs 400.2 ± 123.1 ppb, P < 0.001) and 37.3 ± 23.0 ppb (vs 17.4 ± 18.3 ppb, P < 0.01). A weak correlation between the values measured by NObreath® and Hypair FeNO® devices was observed (r = 0.023 and r = 0.089, respectively; p < 0.05). Conclusions: The handheld NObreath® device is effective in measuring FeNO concentrations in both normal subjects and AR patients. The advantages in price and size, creating a compact, low-cost device that is convenient for use and research.

The prediction of system degradation is very important as it serves as an important basis for the formulation of condition-based maintenance strategies. An effective health indicator (HI) plays a key role in the prediction of system degradation as it enables vital information for critical tasks ranging from fault diagnosis to remaining useful life prediction. To address this issue, a method for monitoring data fusion and health indicator construction based on autoencoder (AE) and long short-term memory (LSTM) network is proposed to improve the predictability and effectiveness of health indicator in this study. Firstly, an unsupervised method and overall framework for HI construction is built based on deep autoencoder and LSTM neural network. The neural network is trained fully based on the normal operating monitoring data and then the construction error of the AE model is adopted as the health indicator of the system. Secondly, we propose related machine learning techniques for monitoring data processing to overcome the issue of data fusion, like mutual information for sensor selection and t-distributed stochastic neighbor embedding (T-SNE) for operating condition identification, etc. Thirdly, in order to verify the performance of the proposed method, experiments are conducted based on CMAPSS dataset and results are compared with algorithms of principal component analysis (PCA) and vanilla autoencoder model. Result shows that LSTM-AE model outperforms the PCA and Vanilla-AE model in metrics of monotonicity, trendability, prognosability and fitness. Fourthly, in order to analyze the impact of the time step of the LSMT-AE model on HI construction, we construct and analyze the system HI curve under different time steps of 5, 10, 15, 20, and 25 cycles. Finally, the results demonstrate that the proposed method for HI construction can effectively characterize the health state of system, which is helpful for further failure prognostics and converting the scheduled maintenance into condition-based maintenance.

We propose a new approach of extending the laser filament plasma channel. By adding a circular aperture quartz plate before the focusing lens, the extension of the plasma channel is doubled. The effects of different diameters, thicknesses of the circular aperture quartz plate and different pulse energies on the length of the plasma channel were investigated. The experimental results show that the thickness of the quartz plate and the depth of the hole have little effects on the plasma channel of the filament, and the diameter of the hole in the center of the quartz plate has a significant effect on the length of the optical filament. The moving-focus model is used to explain the extension of the optical filament.

Copper demand for a country's copper industry has a greater pull effect. China's copper consumption in 2015 has accounted for 50% of the world. The scientific forecast of China's copper demands trend is also an important basis for analyzing its future environmental impact. This paper assumes that China's economy will be developing high, medium and low scenarios, and forecasts economic and social indicators such as total GDP, population and per capita GDP in China from 2016 to 2030. Then, predicted the demand of copper resources in China from 2016 to 2030 by the combination of system dynamics model, vector autoregressive moving average model and inverted U-type empirical model. The results show that: (1) in 2020, 2025 and 2030, China's refined copper demand will be 13 Mt, 15 Mt and 15.5 Mt. (2) China's copper demand growth slowed down significantly from 2016-2030. (3) 2025-2030, China's copper resource demand is stable, into the platform of demand growth, the highest peak value in 2027 will be 15.5 Mt. (4) 2030 years later, China's copper resource demand will enter a slow decline.

Chemistry has been viewed as one of the most fruitful near-term applications to science of quantum computing. Recent work in transitioning classical algorithms to a quantum computer has led to great strides in improving quantum algorithms and illustrating their quantum advantage. Much less effort has been placed on how one finishes these calculations by using the results from the quantum computer (on the active region of the molecule) and embeds them back into the remainder of the molecule in order to determine the properties of the entire molecule. Such strategies are critical if one wants to expand the focus to biochemical molecules that contain active regions that cannot be properly explained with classical algorithms on classical computers. While we do not solve this problem here, we provide an overview of where the field is going to enable such problems to be tackled in the future.

The complete genomic sequence of a Cassava common mosaic virus Linggao isolate (CsCMV-LG) was determined from cassava (Manihot esculenta Crantz) with mild leafy mosaic symptom to no symptom in China. Excluding the poly(A) tail, the CsCMV-LG genome (GenBank accession No. MT038420) is 6374 nucleotides (nts) in length, with five major open reading frames encoding a 1450-amino acids (aa) RNA-dependent RNA polymerase (RdRp), three triple gene block (TGB) proteins (231-aa, 110-aa and 95-aa), and a 229-aa coat protein (CP). Phylogenetic analysis indicated that the complete genome of the CsCMV-LG is closely related to that of CsCMV-Brazilian which has been assigned to the genus Potexvirus, but the sequence identity shared only 88.0%. Notable, the mild CsCMV-LG isolate can also infect Nicotiana benthamiana in laboratory through rub inoculation causing mild vein yellowing at 15-day post inoculation. This is the first full-length genome sequence of a distinct isolate of Cassava common mosaic virus (CsCMV) infecting cassava in Hainan, China.

Research on the development of new lightweight Al-Li alloys using selective laser melting pro-cess has great potential for industrial applications. This paper reports on the development of novel aluminum-lithium alloys using selective laser melting technology. Al-Cu-Li-Mg-Ag-Sc-Zr pre-alloyed powders with lithium contents of 1 wt.%, 2 wt.% and 3 wt.%, respectively, were prepared by inert gas atomization. After SLM process optimization, the microstructure and me-chanical properties of the as-formed specimens were investigated. The densification of the three newly developed alloys are 99.51 %, 98.96 % and 92.01 %, respectively. They all have good form-ability, with the lithium loss rate about 15 %. The as-formed alloy with 1% Li content presents good comprehensive properties with a yield strength of 412.6 ± 16.0 MPa, an ultimate tensile strength of 461.1 ± 11.7 MPa, and an elongation of 13.6 ± 1.1%. The three alloys exhibit a layered molten pool stacking morphology and have a typical heterostructure. The columnar crystals and equiaxed fine grains are alternately arranged, and most of the precipitated phases are enriched at the grain boundaries. The change of Li content mainly affects the precipitation of Cu-containing phase. When the Li content is 1 wt.%, there are θ phase, T1 phase and TB phase. When Li increased to 2 wt.%, T1 and T2 phases precipitated together. When Li reaches 3 wt.%, δ' phase precipitates with T2 phase. This study provides useful guidance for the future SLM form-ing of new crack-free and high-strength Al-Li alloys.

The proton exchange membrane fuel cell (PEMFC) is a critical and essential component of zero-emission electro-hydrogen generators. An accurate prediction of its performance is important for optimal operation management and preventive maintenance of these generators. However, the prediction is not simple because the PEMFCs have complex electrochemical reactions with multiple nonlinear relations between operating variables as inputs and voltage as output. In this paper, we propose an efficient prediction approach based on XGBRegressor and Tree-structured Parzen Estimator. In addition, to better select relevant features, Kernel Principal Component Analysis and Mutual Information are jointly used. The proposed approach allows consideration of the dynamic operating conditions of the PEMFC. To test and validate the robustness of the proposed approach, a real data-set of ten PEMFCs was considered. Furthermore, a comparison study with traditional machine learning models, such as artificial neural networks and support vector machine regression, was investigated. The obtained results confirm that our model outperforms the considered traditionel machine learning models.

: AliCPT-1 is the first Cosmic Microwave Background (CMB) experiment in China, dedicated to achieve accurate measurements of B-mode polarization. Situated in Ali of Tibet, China, this telescope is currently undergoing deployment and will operate in two frequency bands centered at 90 and 150 GHz. The Far-Field Flat Mirror（FFF）is a calibration device of AliCPT-1 telescope for far-field beam mapping. The design of FFF is optimized for easy assembly and adjustment. Meteorological station data reveals that the maximum wind speed near FFF is 17.5 m/s, while the maximum wind speed on the windward side is 8 m/s. The wind pressure on FFF was analysed using a maximum wind speed of 17.5m/s as the input condition, based on the fluid-structure coupling method in ANSYS. The results demonstrate that it is safe and reliable when withstanding combined gravity and wind pressure loads. The torque on the mount is within the motor rated torque. The flatness of the FFF reflective surface can be adjusted to an RMS value of 0.05 mm when taken into account the effect of gravity and assembly accuracy. The deformation caused by the maximum wind loads is approximately 0.0587 mm under the protection of wind-proof wall. The combined deformation is 0.077 mm in RMS value combining the two influences, which is less than 1/20 of wavelength. The FFF mirror assembly is stable and precisely for telescope calibration.

Cucumber (Cucumis sativus L.) is a vital economic vegetable crop, and TRM (TONNEAU1 Recruiting Motif) gene plays a key role in cucumber organ growth. However, the pan-genomic characteristics of the TRM gene family and their expression patterns under different stresses have not been reported in cucumber. In this study, we identified 29 CsTRMs from the pan-genomes of 13 cucumber accessions, with CsTRM29 existing only in PI183967. Most CsTRM proteins exhibited differences in sequence length, except five CsTRMs having consistent protein sequence lengths among the 13 accessions. All CsTRM proteins showed amino acid variations. Analysis of CsTRM gene expression patterns revealed that six CsTRM genes strongly changed in short-fruited lines compared with long-fruited lines. And four CsTRM genes strongly responded to salt and heat stress, while CsTRM14 showed responses to salt stress, powdery mildew, gray mold and downy mildew. Some CsTRM genes were induced or suppressed at different treatment timepoint, suggesting that cucumber TRM genes may play different roles in responses to different stresses, with expression patterns varying with stress changes. Remarkably, the expression of CsTRM21 showed considerable change between long and short fruit and in responses to abiotic stresses (salt stress, heat stress) as well as biotic stresses (powdery mildew, gray mold), suggesting a dual role of CsTRM21 in both fruit shape determination and stress resistance. Collectively, this study provided a base for further functional identification of CsTRM genes in cucumber plant growth and stress resistance.

: The activated carbons (ACs) derived from okara powder waste with high surface areas were modified with ammonia aqueous solution impregnation in an autoclave to enhance their CO2 adsorption properties toward CO2. The impregnated ACs were characterized in which surface chemical composition and properties of the ACs were analyzed by SEM-EDX, FTIR. Activated carbons were functionalized with ammonia aqueous solution (25%) through a hydrothermal process within 24; 48, and 72 hours. The adsorption performance of CO2 onto carbon samples was experimentally evaluated through a TPD CO2 measurement. FTIR spectra confirm the N-containing in N-modified activated carbons and the presence of the –C = O stretch and N-H groups. CO2 uptakes of N-modified activated carbons are 0.24; 1.78; 2.24 and 1.26 mmol/g, which are relatively comparable with those of activated carbons studied in in the literature.

The lower reaches of the Changhua River are located in the northwest of Hainan Island, and the shallow groundwater in this area is the main water source for residents living at both sides of the river. In order to sustain the exploitation and use of water resources in this area, it is essential to clarify the chemical characteristics and the formation mechanism of the groundwater. We collected 100 sets of shallow groundwater samples from the lower reaches of the Changhua River, and analyzed the chemical characteristics of the groundwater in shallow aquifers as well as its controlling factors by means of the methods including descriptive statistical analysis, Piper diagram, Gibbs diagram, and ion ratio. The results show that the overall characteristics of groundwater in the study area are near-neutral to weakly alkaline nature, indicating a generally oxidized environment. The groundwater involves in 56 chemical types, and the most predominant types are Ca•Na-HCO3 and Ca-HCO3, respectively. NO- 3 has become a macro component exceeding SO2- 4in most of the sampling groundwater, suggesting a significant impact of human activities in this area. At the same time, the chemical characteristics of groundwater in the study area are mainly affected by the water-rock interaction, while the water-rock interaction is mostly affected by the dissolution of silicate rocks and less by the dissolution of carbonate rocks and evaporite rocks. According to the ion ratio results, Na+ and K+ in the study area are mainly from the leaching of silicate rocks, Ca2+ and Mg2+ are mainly from the dissolution of carbonate rocks, in addition to a certain degree of cationic exchange. NO- 3 is mainly related to human activities, and the human activities are more affected by agricultural activities and domestic sewage than by industrial and mining activities. This study can provide a reference for the development and protection of shallow groundwater in the lower reaches of the Changhua River.

The interface of a structural system in the soil is usually unsaturated. A decrease in the shear strength of the soil-structure interface can degrade the structure, especially under humid conditions. Studying the shear characteristics of the silt-concrete interface using a shear apparatus. Suction-controlled ring shear tests were carried out on the silt-concrete interface for three interface roughness values. The influence of the matric suction (s) and interface roughness (R) on the shear strength index of the silt-concrete interface was analyzed. The test results showed that high values of s and R improved the shear strength of the interface, but the result was affected by the net normal stress (NNS). High values of NNS and R improved the strain-hardening characteristics. NNS, s, and R significantly affected the interface shear shrinkage. The internal friction angle of the saturated interface was smaller than that of saturated silt, whereas the opposite occurred in the unsaturated state. The cohesion and internal friction angle of the interface rose with an increase in R, and they were larger than that of silt. A shear strength model of the silt and interface was established.

The emergence of non-canonical amino acids (ncAAs) has enriched the functional pool inherent in canonical amino acids (cAAs). ncAAs are important building blocks in the production of various pharmaceuticals. The biosynthesis of ncAAs has emerged as an alternative to traditional chemical synthesis because of its environmental friendliness and high efficiency. The breakthrough genetic code expansion (GCE) technique developed in recent years has allowed for the incorporation of ncAAs into target proteins, giving them special functions and biological activities. Biosynthesis of ncAAs and their incorporation into target proteins within a single microbe has become an enticing application of such molecules. Based on that, in this study we first review the biosynthesis methods for ncAAs and analyze the difficulties in biosynthesis. We then summarize the GCE methods and analyze their advantages and disadvantages. Further, we review the application progress of ncAAs and anticipate the challenges and future development directions of ncAAs.

Lithium rich layered oxides (LRLO) are a wide class of innovative active materials for positive electrodes in lithium-ion (LIB) and lithium-metal secondary batteries (LMB). LRLOs are over-stoichiometric layered oxides rich in lithium and manganese, with general formula Li1+xTM1-xO2, where TM is a blend of transition metals comprising Mn (main constituent), Ni, Co, Fe and others. Due to the very variable composition and the extended defectivity their structural identity is still debated among researchers being likely an unresolved hybrid between a monoclinic (mC24) and a hexagonal lattice (hR12). Once casted in composite positive electrode films and assembled in LIBs or LMBs, LRLOs can delivery reversible specific capacities above 220-240 mAhg-1, thus beyond any other available intercalation cathode material for LIBs, with mean working potential above 3.3-3.4 V vs Li for hundreds of cycles in liquid aprotic commercial electrodes. In this review we critically outline the recent advancements in the fundamental understanding of the physico-chemical properties of LRLO as well as the most exciting innovations in their battery performance. We focus in particular on the elusive structural identity of these phases, on the complexity of the reaction mechanism in batteries as well as on practical strategies to minimize or remove cobalt from the lattice while preserving the outstanding performance upon cycling.

Europium (Eu)-doped fluorapatite (FA) nanorods has a similar biocompatibility with hydroxyapatite (HA) in terms, attracted much attention as cell imaging biomaterials due to their luminescent property. Here, we will discuss the new feature of europium doped fluorapatite (Eu-FA) nanorods as anticancer drug carrier. Eu-FA nanorods was prepared using a hydrothermal method. The morphology, crystal structure, fluorescence and composition are investigated. The specific crystal structure, enabling an effective loading of drug molecules. Doxorubicin (DOX), used as an anticancer model drug, was shown to be effectively loaded onto the surface of the nanorods. The DOX release was fairly pH-dependent, occurring more rapidly at pH 5.5 than pH 7.4 was observed. The intracellular penetration of the DOX-loaded Eu-FA nanorods (Eu-FA/DOX) can be imaged in situ due to the self-fluorescence property. Treatment of melanoma A375 cells with Eu-FA/DOX elicited a more effective apoptosis rate than direct DOX treatment. Overall, Eu-FA show great promise for tracking and treating tumor, may potentially useful as a multifunctional carrier system to effectively load and sustainably deliver drugs.

Lyme disease (LD) is a tick-transmitted infection caused by Borrelia burgdorferi sensu lato species which includes B. burgdorferi, B. afzelii, and B. garinii. The majority of patients with early LD can be cured by standard treatment, yet some still suffer from post-treatment Lyme disease syndrome (PTLDS). The presence of Borrelia persisters has been proposed as a contributing factor, which cannnot be completely killed by the currently used antibiotics for Lyme disease. Finding new pharmaceuticals targeting Borrelia persisters is crucial in developing more effective treatment. Here, we first confirmed the existence of persisters in cultures of B. garinii and B. afzelii and then conducted high-throughput screening of a custom drug library against persister-rich stationary-phase cultures of B. garinii and B. afzelii. Among 2427 compounds screened, hypocrellin A (HA), anthracycline class of drugs, and topical antibiotics along with some other natural compounds were identified to have strong potential in killing persisters of B. garinii and B. afzelii. HA was the most active anti-Borrelia compound, capable of eradicating stationary-phase Borrelia persisters, in particular when combined with doxycycline and/or ceftriaxone. Liposoluble antioxidant vitamin E was found to antagonize the activity of HA, indicating HA’s target is the cell membrane where HA-triggered reactive oxygen species (ROS) generation took place in the presence of light. HA was found to have distinct bactericidal activity against Borrelia species but had poor or no activity against Gram-positive and Gram-negative bacteria. Identification of the above-mentioned drug candidates may help to develop more effective therapies for LD.

Reducing CO2 emissions is urgently needed to slow down the impacts of climate change. CO2 capture using an amine solution has been developed and implemented on pilot and commercial scales. However, amine scrubbing, in particular, produces a lot of degraded solvent as waste and is energy intensive. Solid sorbents have been called to overcome those drawbacks. In this work, waste biomass-derived carbon materials were developed and tested for CO2 capture and conversion. Advanced thermal chemical processes i.e. hydrothermal and pyrolysis were applied to produce materials from agri-food waste such as soybean and okara. It was found that the number of functional groups (-C=O and -OH) in activated carbon appears in the synthesized materials, implying the generation of surface oxygenated groups. Preliminary results showed that the synthesized activated carbons are obtained with good yields, and a relatively high surface area, which may be applied as CO2 adsorption materials to solve the CO2 emission problems.

p-Hydroxyphenylpyruvate dioxygenase (HPPD) is not only the useful molecular target in treating life-threatening tyrosinemia type I, but also an important target for chemical herbicides. A combined in silico structure-based pharmacophore and molecular docking based virtual screening were performed to identify novel potential HPPD inhibitors. The complex based pharmacophore model (CBP) with 0.721 of ROC used for screening compound showed remarkable ability to retrieve known active ligands from decoy molecule. The ChemDiv database was screened using CBP-Hypo2 as a 3D query, and the best-fit hits subjected to molecular docking with two methods of LibDock and CDOCKER in Accelrys Discovery Studio 2.5(DS 2.5) to discern interactions with key residues at the active site of HPPD. 4 Compounds with top rank in HipHop model and well-known binding model were finally chosen as identification of lead compounds with potentially inhibitory effects on active site of target. The results provided powerful insight to the development of novel HPPD inhibitors herbicides using computational techniques.

In pattern recognition domain, deep architectures are widely used nowadays and they have achieved fine grades. However, these deep architectures need special demands, especially big datasets and GPU. Aiming to gain better grades without deep networks, we propose a simplified algorithm framework using fusion features extracted from the salient areas of faces. Furthermore, the proposed algorithm has achieved a better result than some deep architectures. For extracting more effective features, this paper firstly defines the salient areas on the faces. This paper normalizes the salient areas of the same location in the faces to the same size, therefore it can gain more similar features from different subjects. LBP and HOG features are extracted from the salient areas, fusion features’ dimensions are reduced by Principal Component Analysis( PCA) and we apply softmax to classify the six basic expressions at once. This paper proposes a salient areas definitude method which uses peak expressions frames to compare with their neutral faces. This paper also proposes and applies the idea of normalizing the salient areas to align the specific areas which express the different expressions. This makes the salient areas found from different subjects have the same size. Besides, gamma correction method is firstly applied on LBP features in our algorithm framework which improves our recognition rates significantly. By applying this algorithm framework, our research has gained state-of-the-art performances on CK+ database and JAFFE database.

Quantifying the landscape pattern change can effectively demonstrate the ecological progresses and the consequences of urbanization. Based on remotely sensed land cover data in 1994, 2000, 2006 and a gradient analysis with landscape metrics at landscape- and class- level, we attempted to characterize the individual and entire landscape patterns of Shanghai metropolitan during the rapid urbanization. We highlighted that a roadscape transect approach that combined the buffer zone method and the transect-based approach was introduced to describe the urban-rural patterns of agricultural, residential, green, industrial, and public facilities land along the railway route. Our results of landscape metrics showed significant spatiotemporal patterns and gradient variations along the transect. The urban growth pattern in two time spans conform to the hypothesis for diffusion–coalescence processes, implying that the railway is adaptive as a gradient element to analyze the landscape patterns with urbanization. As the natural landscape was replaced by urban landscape gradually, the urban fringe expanded radically. The results also showed that the desakota region expanded its extent widely. Satellite towns witnessed the continual transformation from the predominantly rural landscape to peri-urban landscape. Furthermore, the gap between urban and rural areas remained large especially in public service. More reasonable urban plans and land use policies should push to make more of an effort to transition from the urban-rural separation to coordinated urban-rural development. This study is a meaningful trial in demonstrating a new form of urban–rural transects to study the landscape change of large cities from a strategic viewpoint. By combining gradient analysis with landscape metrics, we addressed the process of urbanization both spatially and temporally, and provided a more quantitative approach to urban studies.

Discrete distribution estimation is a fundamental statistical tool, which is widely used to perform data analysis tasks in various applications involving sensitive personal information. Due to privacy concerns, individuals may not always provide their raw information, which leads to unpredictable biases in the final results of estimated distribution. Local Differential Privacy (LDP) is an advanced technique for privacy protection of discrete distribution estimation. Currently, typical LDP mechanisms provide same protection for all items in the domain, which imposes unnecessary perturbation on less sensitive items and thus degrades the utility of final results. Although, several recent works try to alleviate this problem, the utility can be further improved. In this paper, we propose a novel notion called Item-Oriented Personalized LDP (IPLDP), which independently perturbs different items with different privacy budgets to achieve personalized privacy protection. Furthermore, to satisfy IPLDP, we propose the Item-Oriented Personalized Randomized Response (IPRR) based on the observation that the sensitivity of data shows an inverse relationship with the population size of respective individuals. Theoretical analysis and experimental results demonstrate that our method can provide fine-grained privacy protection and improve data utility simultaneously.

Near-surface humidity (Qa) is a key parameter that modulates oceanic evaporation and influences the global water cycle. Remote sensing observations act as feasible sources for long-term and large-scale Qa monitoring. However, existing satellite Qa retrieval models are subject to apparent uncertainties due to model errors and insufficient training data. Based on in situ observations collected over the China Seas over the last two decades, a deep learning approach named Ensemble Mean of Target deep neural networks (EMTnet) was proposed to improve the satellite Qa retrieval over the China Seas for the first time. The EMTnet model outperforms five representative existing models by nearly eliminating the mean bias and significantly reducing the root-mean-square error in satellite Qa retrieval. According to its target deep neural networks selection process, the EMTnet model can obtain more objective learning results when the observational data are divergent. The EMTnet model was subsequently applied to produce a 30-year monthly gridded Qa data over the China Seas. It indicates that the climbing rate of Qa over the China Seas under the background of global warming are probably underestimated by current products.

Null-flux Electro-dynamic suspension (EDS) system promises to be one of the feasible high-speed maglev systems above 600 km/h. On account of its greater current-carrying capacity, superconducting magnet can provide super-magnetomotive force that is required for null-flux EDS system and cannot be provided by electromagnets and permanent magnets. There is already a relatively mature high-speed maglev technology with low temperature superconducting (LTS) magnets as the core, which works in the liquid helium temperature region (T≤4.2 K). 2-Generation high temperature superconducting (HTS) magnet winded by REBa2Cu3O7−δ (REBCO, RE=rare earth) tapes works above 20 K region and do not need to count on liquid helium which is rare on earth. This paper designed HTS no-insulation closed-loop coils applied for EDS system and energized with persistent current switch. The coils can work at persistent current model and has premier thermal quench self-protection. Besides, a full size double-pancake module was designed and manufactured in this paper, and it was tested in liquid nitrogen. The double-pancake module’s critical current is about 54 A and it is capable of working at persistent current model, whose average decay rate measured in 12 hours is 0.58%/day.

In Acropora, the complex canals in a coral colony connect all polyps into a holistic network to collaborate in performing biological processes. There are various types of canals, including calice, axial canals, and other internal canals, with structures that are dynamically altered during different coral growth states due to internal calcium transport. However, few studies have considered the regulation of calcium transport in Acropora. In this study, we investigated the morphological changes of the axial canal in six Acropora muricata samples by high resolution micro-computed tomography, observing the patterns of the axial canal during the processes of new branch formation and truncated branch rebuilding. We visualized the formation of a new branch from a calice and deposition of the iconic hexactin skeletons in the axial canal. Furthermore, the diameter and volume changes of the axial canal in truncated branches during rebuilding processes were calculated, revealing that the volume ratio of calcareous deposits in the axial canal exhibit significant increases within the first three weeks, returning to levels in the initial state in the following week. This work indicates that the axial canal can transport calcium to form hexactin skeletons in a new branch and rebuild the tip of a truncated branch. The calcium transport along canal network regulates various growth processes, including budding, branching, skeleton forming, and self-rebuilding of an Acropora colony. Understanding the changes in canal function under normal and extreme conditions will provide theoretical guidance for restoration and protection of coral reefs.

After cut by basecutter, sugarcane stalks are carried to a chopper by the basecutter and the feeding/conveying rollers train of harvester. However, the conventional feeding/conveying channels of sugarcane chopper harvesters, when harvesting seriously lodged sugarcane, have numerous drawbacks, including easy clogging, and poor adaptability. In order to resolve these problems, a novel design and layout method of feeding/conveying and chopping channel are proposed in the paper. And a chopper centrally-mounted channel is designed for a sugarcane chopper harvester as well, which has been implemented in the HN4GDL-91 harvester. The proposed channel consists of a feeding/conveying rollers train, a chopper, and a billet conveying device. By mounting the chopper between the feeding/conveying rollers train and the billets conveying device, the harvester can avoid the chopper chopping back the billets, thus improving the harvest quality. The feeding/conveying rollers train is designed with only a pair of feeding rollers and a pair of conveying rollers, achieving a short channel path. Moreover, the structure of the basecutter and the mechanism carrying stalks to feeding rollers are studied via theoretical analysis and tests. The relationship between the basecutter and the chopper centrally-mounted channel is also conducted in systematic analysis. The results of the theoretical analysis show that the inclination angle of the disc of basecutter should be 2° greater than the angle of the feeding conveying channel (both angles are from the horizontal plane). The inclination angle of the disc of basecutter should go from 10° to 15°. A field experiment with four factors and three levels indicates that the field loss rate is 2.45%, the feed quantity is 16.66 kg/s, and the qualified rate of the billets is 98.02%, while the number of sugarcane stalks in a clump, the ground speed of harvester the rotational speed of the chopper, and the rotational speed of feeding/conveying roller are 10, 1.09 m/s, 390 r/min, and 230 r/min, respectively. It is concluded that the proposed chopper centrally-mounted channel could improve the conveying and harvesting performance significantly.

ALDH+ H1975 lung adenocarcinoma stem cells (LSCs) are a rare cell population identified in lung adenocarcinoma (LUAD). LSCs can self-renew, drive tumor initiation, growth, metastasis, and recurrence, and are also the predominant cause of poor prognosis due to their intrinsic resistance to drugs and chemotherapy. Consequently, LSCs are a promising target for LUAD therapy. Noncoding RNAs (ncRNAs), including microRNAs (miRNAs), long noncoding RNAs (lncRNAs), and circular RNAs (circRNAs), exert many significant regulatory functions in the pathogenesis of human cancers, showing the necessity for a comprehensive understanding of the mechanisms that underlie lung carcinogenesis. Nonetheless, research on many known transcripts and messenger RNAs (mRNAs) has already generated new information. Unknown biomarkers in ncRNAs and systematic and comprehensive interrelation with unknown ncRNAs and mRNAs may provide further insights into the biology of LUAD. Herein, a set of novel ncRNAs that include miRNAs, lncRNAs, circRNAs, were identified and differentially expressed patterns of ncRNAs and mRNAs in LSCs and ALDH- H1975 LUAD tumor cells (LTCs) were obtained using stringent bioinformatics pipelines. Through a meta-analysis of the identified landscapes, novel competitive endogenous RNA (ceRNA) networks were constructed to reveal the potential molecular mechanisms that regulate the hallmarks of LSCs and LTCs. This study presents a summary of novel ncRNAs and the fundamental roles of differentially expressed ncRNAs implicated in the activity of LSCs and LTCs. In addition, the study also provides a comprehensive resource for the future identification of diagnostic, therapeutic, and prognostic biomarkers in LUAD.

An emerging picture in cancer biology is that, paradoxically, chemotherapy can actively induce changes that favor cancer progression. These pro-cancer changes can be either inside (intrinsic) or outside (extrinsic) the cancer cells. In this review, we will discuss the extrinsic pro-cancer effect of chemotherapy; that is, the effect of chemotherapy on the non-cancer host cells to promote cancer progression. We will focus on metastasis, and will first discuss recent data from mouse models of breast cancer. Intriguingly, despite reducing the size of primary tumors, chemotherapy changes the tumor microenvironment, resulting in an increased escape of cancer cells into the blood stream. Furthermore, chemotherapry changes the tissue microenvironment at the distant sites, making it more hospitable to cancer cells upon their arrival. We will then discuss the idea and evidence that these devastating pro-metastatic effects of chemotherapy can be explained in the context of stress response. At the end, we will discuss the potential relevance of these mouse data to human breast cancer and their implication on chemotherapy in the clinic.

Photosynthetic function, photoprotection, and the response of related proteomics of mulberry (Morus alba L.) seedling leaves under NaCl and NaHCO3 stress with the same Na+ concentration (100 mmol•L-1) were studied by using photosynthetic gas exchange and chlorophyll fluorescence techniques combined with TMT proteomics. The results showed that NaCl stress had no significant effect on photosystem II (PSII) activity in mulberry seedling leaves, and the expressions of the related proteins, OEE3-1 and PPD4, of the PSII oxygen-evolving complex (OEC) and the antenna proteins, CP24 10A, CP26, and CP29, of LHCII in the leaves also increased to varying degrees. The photosystem I (PSI) activity in the leaves of mulberry seedling also increased, and the expressions of some proteins, PsaF, PsaG, PsaH, PsaL, PsaN, and Ycf4, in PSI increased significantly under NaCl stress. Under NaHCO3 stress, the activity of PSII and PSI and the expression of their protein complexes and the electron transfer-related proteins significantly decreased. NaCl stress had little effect on RuBP regeneration during dark reaction in the leaves and the expressions of glucose synthesis related proteins and net photosynthetic rate (Pn) did not decrease significantly. The leaves could adapt to NaCl stress by reducing stomatal conductance (Gs) to increase water use efficiency (WUE). Under NaHCO3 stress, the expression of dark reaction-related proteins was mostly down-regulated, and Gs was significantly reduced, which indicated that non-stomatal factors were important reasons for the significant inhibition of carbon assimilation. In the photoprotective mechanism under NaCl stress, the expression of cyclic electron flow (CEF) related proteins, ndhH, ndhI, ndhK, and ndhM, involved in NAD(P)H dehydrogenase (NDH) and the key enzyme of the xanthophyll cycle, violaxanthin de-epoxidase (VDE) were up-regulated. In addition, the ratio of xanthophyll cycle components (A+Z)/(V+A+Z) was increased. The expressions of proteins FTR and Fd-NiR, which are related to Fd-dependent ROS metabolism and nitrogen metabolism, were also significant up-regulated under NaCl stress, which can effectively reduce the electronic pressure on Fd. Under NaHCO3 stress, the expressions of CEF-related proteins, VDE, ZE, FTR, Fd-NiR, Fd-GOGAT, SGAT, and GGAT, were significant down-regulated, and the photoprotective mechanism, like the xanthophyll cycle, CEF, and photorespiration, might be damaged, resulting in the inhibition of PSII activity and carbon assimilation in leaves of mulberry seedling under NaHCO3 stress.

The influence of pH, temperature, biopolymer ratio, total concentration, and ionic concentration on the interaction between egg white protein (EWP) and chitosan (CS) was investigated through turbidity, zeta potential, and state diagram in our research. In addition, phase behavior was observed under various conditions. The turbidity of EWP remained low (turbidity&lt;0.03) and basically unchanged at a wide range of pH (4.0-8.0), while the turbidity of CS was slightly higher (turbidity&lt;0.2) after pH 7.0 than before. Moreover, under the same conditions, a sharply rising peak pattern was observed for the complex between EWP and CS. The maximum turbidity value was observed at 55°C, and the temperature had a mild effect on turbidity. The optimum EWP to CS ratio was found to be 12:1 based on the experiment of the turbidity curves and state diagrams influenced by different biopolymer mixing ratios. With the enhanced concentrations of total biopolymer, the maximum turbidity rose insignificantly above 0.1%.

Human pose estimation is a complex detection task in which the network needs to capture the rich information contained in the images. In this paper, we propose MSTPose (Multi-Scale Transformer for human Pose estimation). Specifically, MSTPose leverages a high-resolution Convolution neural network (CNN) to extract texture information from images. For the feature maps from three different scales produced by the backbone network, each branch performs the coordinate attention operations. The feature maps are then spatially and channel-wise flattened, combined with keypoint tokens generated through random initialization, and fed into a parallel Transformer structure to learn spatial dependencies between features. As the Transformer outputs one-dimensional sequential features, the mainstream two-dimensional heatmap method is abandoned in favor of one-dimensional coordinate vector regression. The experiments show that MSTPose outperforms other CNN-based pose estimation models and demonstrates clear advantages over CNN + Transformer networks of similar types.

Obsessive-Compulsive Disorder (OCD) is a mental health condition marked by recurrent intrusive thoughts or sensations that compel individuals to perform repetitive behaviors or mental acts. Obsessions and compulsions significantly disrupt daily life and cause considerable distress. Early identification and intervention improve long-term outcomes. This study aimed to evaluate the ability of four advanced artificial intelligence models (ChatGPT-3.5, ChatGPT-4, Claude, and Bard) to accurately recognize OCD compared to human professionals and to assess recommended therapies and stigma attributions. This study was conducted during March 2024 utilizing 12 vi-gnettes. Each vignette depicted a client, either a young adult or a middle-aged male or female, attending an initial therapy session. Each vignette was evaluated ten times, resulting in 480 evaluations. The results were compared with those of a human sample of 514 psychotherapists, as reported by Canavan. Significant differences were found. AI models demonstrated higher OCD recognition rates and confidence levels than human professionals and showed 100% confidence in recognition, compared to 87% among psychotherapists. AI models also recommended evi-dence-based interventions more frequently, with ChatGPT-3.5 and Claude at 100%, ChatGPT-4 at 90%, and Bard at 60%, compared to 61.9% among psychotherapists. Additionally, AI models ex-hibited significantly lower stigma and danger estimations, though both AI and psychotherapists demonstrated high willingness to treat the described cases. The findings suggest that AI models surpass human professionals in recognizing OCD and recommending evidence-based treatments while also demonstrating lower stigma. These results highlight the potential of AI tools to enhance OCD diagnosis and treatment in clinical settings.

Sclerotinia sclerotiorum is a devastating fungal pathogen that causes severe crop losses worldwide. It is of vital importance to understand its pathogenic mechanism for disease control. Through a forward genetic screen combined with next-generation sequencing, a putative protein kinase, SsCak1, was found to be involved in growth and pathogenicity of S. sclerotiorum. Knockout and complementation experiments confirmed that deletions in SsCAK1 caused defects in mycelium and sclerotia development, as well as appressoria formation and host penetration, leading to complete loss of virulence. These findings suggest that SsCak1 is essential for growth, development and pathogenicity of S. sclerotiorum. Therefore, SsCak1 could serve as a potential target for the control of S. sclerotiorum infection through host-induced gene silencing (HIGS), which could increase crop resistance to the pathogen.

Here, we have discovered a X-ray excited long afterglow phosphor β-NaYF₄: Tb³⁺. After the irradiation of X-ray, the green emission can persist for more than 240 h. After 36 h, the afterglow intensity arrived at 0.69 mcd•m^-2, which can clearly be observed by naked eyes. Even after 84 h, the afterglow emission brightness still reached 0.087 mcd•m^-2. Also, combined with the results of thermoluminescence and photoluminescence, the super long afterglow emission of β-NaYF₄: Tb³⁺ can be ascribed to the tunneling model associated with F centers. More importantly, the super long green afterglow emission of β-NaYF₄: Tb³⁺ has been successfully used as in vivo light source to activate g-C₃N₄ for photodynamic therapy（PDT）and bacteria destruction. Furthermore, super long persistent luminescence of β-NaYF₄: Tb³⁺ could be repeatedly charged by X-ray for many circulations, which indicates that the phosphors have high photo stability under repeated cycles of alternating X-ray irradiation.

Adult neural stem and progenitor cells (NSPCs) contribute to learning, memory, maintenance of homeostasis, energy metabolism and many other essential processes. They are highly heterogeneous populations that require input from a regionally distinct microenvironment including a mix of neurons, oligodendrocytes, astrocytes, ependymal cells, NG2+ glia, vasculature, cerebrospinal fluid (CSF), and others. The diversity of NSPCs is present in all three major parts of the CNS, i.e., the brain, spinal cord, and retina. Intrinsic and extrinsic signals, e.g., neurotrophic and growth factors, master transcription factors, and mechanical properties of the extracellular matrix (ECM), collectively regulate activities and characteristics of NSPCs: quiescence/survival, proliferation, migration, differentiation, and integration. This review discusses the heterogeneous NSPC populations in the normal physiology and highlights their potentials and roles in injured/diseased states for regenerative medicine.

RNA interference (RNAi) is one of the main mechanisms for disease resistance and small RNA production in plants. The main proteins involved in RNAi include Dicer-like (DCL), RNA-dependent RNA polymerase (RDR), double-stranded RNA-binding (DRB), and Argonaute (AGO). Juglandaceae contains a variety of important woody plants, and walnuts are one of the four major woody plant groups and one of the four major dried fruits in the world. To clarify the evolution and functional differentiation of RNAi-related proteins in the walnut (Juglans regia) genome, this study integrated various web resources from gene family acquisition to structural analysis and transcriptome data to correlate walnuts and their congeners. The walnut genome has 5 DCL, 13 RDR, 15 DRB and 15 AGO genes, similar genes encoding conserved protein structural domains and conserved motifs with similar subcellular localization. Walnut AGO proteins are classified into three classes and seven subclasses. The DCL is divided into four categories, while RDR is mainly divided into four categories, and DRB can be divided into six categories. The exception is that the copy number of walnut RDR1 is 9, in which seven RDR1 are distributed in clusters on chromosome 16. Purifying selection drove the formation of walnut genes, but protein classes were subjected to varying degrees of purifying selection. Additionally, these results showed some similarity in other plants of the walnut family. Moreover, different RNAi-related genes of walnut produced abundant selective expression in response to different tissues and stresses. In this study, DCL, RDR, DRB and AGO gene families were identified and analysed in the genome of the walnut family for the first time and preliminarily examined the evolution, structure and expression characteristics of these families to provide a preliminary basis for the evolution of the walnut RNAi pathway and breeding research.

The unique characteristics of frescoes on overseas Chinese buildings can attest to the integration and historical background of Chinese and Western cultures. Reasonable analysis and preservation of overseas Chinese frescoes can provide sustainable development for culture and history. This research adopts the image analysis technology based on artificial intelligence, and proposes a ResNet-34 model and method integrating transfer learning. This deep learning model can identify and classify the source of the frescoes of the emigrants, and can effectively deal with the problems such as the small number of fresco images on the emigrants' buildings, poor quality, difficulty in feature extraction, and similar pattern text and style. The experimental results show that the training process of the model proposed in this article is stable. On the constructed Jiangmen and Haikou fresco JHD datasets, the final accuracy is 98.41%, and the recall rate is 98.53%. The above evaluation indicators are superior to classic models such as AlexNet, GoogLeNet, and VGGNet. It can be seen that the model in this article has strong generalization ability and is not prone to overfitting. It can effectively identify and classify the cultural connotations and regions of frescoes.

Purpose: Acute kidney injury (AKI) is a severe symptom of the 2019 novel coronavirus disease (COVID-19), especially for patients in a critical condition.This study explored the potential mechanism of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) on AKI at the single-cell level. Methods: 15 normal human kidney samples were collected and analyzed using single-cell RNA sequencing (scRNA-seq). Subsequently, we analyzed the components and proportions of kidney cells expressing the host cellular receptor ACE2 and the key protease TMPRSSs family, and analyzed the expression differences in Occidental and Asian populations. Results: We drafted the currently available world's largest human kidney cell atlas with 42,589 cells and identified 19 clusters through unsupervised hierarchical clustering analysis. ACE2 and TMPRSSs genes were significantly co-expressed in podocytes and proximal convoluted tubules as potential host cells targeted by SARS-CoV-2. Comparative analysis showed that ACE2 expression in kidney cells was no less than that in the lung, esophagus, small intestine and colon, suggesting that the kidney may be an important target organ for SARS-CoV-2. In addition, given the high expression of ACE2 and kidney disease-related genes in Occidental donors relative to Asian donors, Occidental populations with SARS-CoV-2 infection might be a higher risk of of kidney injury.

Motivation: there is a paradox at the heart of informatics where practical implementation generally fails to understand the socio-technical impact of novel technologies and disruptive innovation when adopted in `real-world’ systems. This phenomenon, termed technological determinism, is manifested in a time-lag between the adoption of novel technologies and an understanding of the underlying theory which develops following research into their adoption. Methods: we consider informatics theory as it relates to: social informatics and how humans’ function in society, the relationship between society and technology, information systems, information systems design, and human-computer interactions. The challenges posed by novel technologies and disruptive innovation are considered as they relate to information systems and information systems design. Open research questions with directions for future research are discussed with an introduction to and our proposed approach to socio-technical information system design. Significance: we conclude that the adoption of disruptive innovation presents both opportunities and threats for all stakeholders in computerised systems. However, determinism is a topic requiring research to generate a suitable level of understanding and technological determinism remains a significant challenge.

Earthquake-triggered landslides represent a significant seismic-related disaster, posing threats to both the lives and properties of individuals in affected areas. Furthermore, they can result in road and river blockages, as well as other secondary disasters, significantly impacting post-earthquake rescue efforts. Efficient and accurate rapid assessment of high-risk landslide zones carries important implications for decision-making in disaster response and for mitigating potential secondary disasters. This study uses the high-intensity Zone VII to IX of the 5 September 2022 Luding Ms6.8 earthquake as a case study. The "difference method" and the "cumulative displacement method," based on the simple Newmark model, are employed to assess earthquake-triggered landslides. The evaluation results from both methods demonstrate that the areas posing an ex-tremely high risk of earthquake-triggered landslides are predominantly situated on the western side of the Xianshuihe Fault. Actual landslide data verification shows that both models have high predictive accuracy, with the difference method model slightly outper-forming the cumulative displacement method model. Moreover, the study recommends determining threshold values for each landslide hazard interval with significant physical meaning using past strong earthquake data as soon as possible when utilizing the difference method to assess the risk of earthquake-triggered landslides.

Biotic and abiotic factors influence the formation of fungal-algal pairings in lichen symbiosis. It is poorly known which factors determine the specific associations, especially when distantly related fungi are considered. Here, we investigated the effect of different drivers on the association patterns of taxonomically diverse lichenized fungi and their trebouxioid symbiotic partners. In 200 samples collected across three biomes, we found 41 species of lichenized fungi, associating with 16 species of trebouxioid green algae, of which 62% were previously unreported. Species identity of the fungal and algal partner had the greatest effect on the outcome of the symbiosis compared with abiotic factors such as climatic variables and geographic distance. Partner specificity was found to be higher in tropical regions than in temperate and arctic regions. Co-phylogenetic analyses indicated congruent phylogenies of trebouxioid algae and associated fungi, rejecting their random associations. Evolutionary mechanisms contributing most to the observed phylogenetic patterns were ‘loss’ and ‘failure to diverge’ of the algal partners. This study broadens our knowledge of fungi-algae symbiotic patterns in view of Trebouxia-associated fungi.

Tuberculosis (TB) remains a global healthcare crisis with an estimated 10 million new cases and 1.4 million deaths per year TB is caused by infection with the major human pathogen Mycobacte-rium tuberculosis, which is difficult to rapidly diagnose and treat. There is an urgent need for new methods of diagnosis, sufficient in vitro models which capably mimic all physiological condi-tions of the infection, and high-throughput drug screening platforms. Microfluidic-based tech-niques provide single-cell analysis which reduces experimental time, the cost of reagents, and have been extremely useful for gaining insight into monitoring microorganisms. This review out-lines the field of microfluidics and discusses the use of this novel technique so far in M. tuberculo-sis diagnostics, research methods, and drug discovery platforms. The practices of microfluidics have promising future applications for diagnosing and treating TB.

A new algorithm is developed in this study to automatically detect reinforced concrete structures' rebar locations and diameters using the ground penetrating radar technique. The method approximates the hyperbolic signatures using two-way travel time and bi-quadratic equations. The study includes formulating electromagnetic wave speed in reinforced concrete (RC) structures. The algorithm was used in a computer code to provide an automated analysis of ground-penetrating radar data collected from a pre-planned survey grid. Two RC slabs were fabricated and tested to validate the proposed method. The proposed method is efficient in signal processing and accurately and reliably determining the rebar information.

BackgroundIntracranial hemorrhage (ICH) in pregnancy, estimated at 1 in 10,000 cases, presents significant diagnostic challenges prenatally despite advanced imaging techniques such as ultrasound (US) and MRI. Detecting ICH is crucial for pregnancy management and future treatment decisions aimed at improving fetal survival and reducing brain damage. This report presents the diagnosis and outcomes of two cases of prenatal ICH.Cases presentationThe first case involves a 30-year-old pregnant woman with irregular prenatal care diagnosed with ICH at 32 weeks of gestation via US and MRI. She chose to continue the pregnancy, delivering a 3160g male infant at 36 weeks via cesarean section. Following NICU care including resuscitation and ventriculoperitoneal shunt placement, the infant was discharged. Subsequent examinations showed a reduction in ventricle size. In the second case, a 27-year-old woman taking acenocoumarol for a mechanical heart valve developed fetal subdural hemorrhage detected by US and MRI. She opted to terminate the pregnancy, resulting in a stillborn male infant weighing 1530g.ConclusionFetal ICH presents with varying severity and prognostic implications, diagnosed and graded using US. Fetal cranial MRI may help clarify the etiology. Management remains controversial, with termination of pregnancy potentially warranted in severe cases due to poor prognosis. Further research is needed to refine management and improve outcomes in fetal ICH.

Abstract: The traditional model of closed circuit ball milling systems has been used for several decades, however, if the classifier of the closed circuit ball mill system performs the duties of both pre-classification and check-classification, the characterization error of the traditional model is large. To address this problem, a new model is obtained by modifying and supplementing the traditional one. The most important feature of the new model compared to the traditional model is that the circulating load is considered to be the fresh feed for the entire system rather than the ball mill. The error between the slurry level height calculated using the traditional model and the actual is 52.31%, which is 13.77 times higher than that of the new model. When the relative capacity varies greatly, that of the ball mill calculated by the traditional model fluctuates between 0.95 and 1.15, while the new model is 0.6 to 1.4. The new model has a higher accuracy than the traditional model in characterizing the production status of the grinding system, which is of some significance for industrial production.

Colorectal liver metastases (CRLM) patients combined with hepatic lymph node metastases was a negative prognostic factor associated with outcomes. Up to now, there was still lack of a reliable method to identify the status of hepatic lymph nodes. The aim of this study was to investigate the predictive ability of mono-exponential, bi-exponential, and stretched-exponential diffusion-weighted imaging (DWI) models to distinguish between benign and malignant hepatic lymph nodes in CRLM patients who underwent neoadjuvant chemotherapy prior to surgery. In total, 97 CRLM patients with pathologically proved hepatic lymph node status were included. Various quantitative parameters, including the apparent diffusion coefficient (ADC) from mono-exponential model, D, D*, and f derived from intravoxel incoherent motion (IVIM) model, as well as DDC and α from stretched-exponential model (SEM), were measured. Multivariate analysis revealed that the pre- treatment DDC value and the short diameter of the largest lymph node after treatment were independent predictors of metastatic hepatic lymph nodes. A nomogram combining these two factors demonstrated excellent performance in distinguishing between benign and malignant lymph nodes in CRLM patients, with an area under the curve (AUC) of 0.873. Therefore, the nomogram can serve as a preoperative assessment tool for determining the status of hepatic lymph nodes and aiding in the decision-making process for surgical treatment in CRLM patients.

To further explore the bearing capacity and sustainable construction of vacuum drainage pipe (VDP) piles, field tests were carried out to compare and analyze the ultimate single pile bearing capacity, pile side friction and pile end resistance of ordinary piles and vacuum drainage pipe piles. The effect of the VDP pile on energy conservation and emission reduction in practical projects is discussed. The results shows that the VDP pile basically eliminated the soil squeeze and did not cause excessive relative displacement of pile and soil after vacuum consolidation. The VDP pile enhances pile side friction resistance, resulting in a 17.6% increase in ultimate bearing capacity compared to traditional piles. The VDP pile method can reduce carbon emissions by 31.4% compared to traditional methods. This study provides guidance for the production and design of VDP piles in the future and demonstrates their potential for energy conservation and emission reduction benefits compared to traditional methods.

The aim of this paper is to use the elementary method and the properties of the second kind Stirling numbers to study the congruence properties of a new sequence, which is closely related to Fubini polynomials and Euler numbers, and give some interesting congruences for it. This solves a problem proposed by the first author at an unpublished paper.

Sympatric distribution and temporal overlap of cryptic zooplankton species pose a challenge to the framework of the niche differentiation theory and the mechanisms allowing competitor coexistence. We applied the methods of phylogenetic analysis, DNA taxonomy and statistical analysis to study the temporal distribution patterns of cryptic B. calyciflorus species, an excellent model, in three lakes, and to explore the putative mechanisms for their seasonal succession and temporal overlap. The results showed that in the warm-temperate Lake Yunlong, B. fernandoi and B. calyciflorus s.s. underwent a seasonal succession, which was largely attributed to their differential adaptation to water temperature. In the subtropical Lake Jinghu, B. fernandoi, B. calyciflorus s.s. and B. dorcas exhibited both seasonal succession and temporal overlap. Seasonal successions were largely attributed to their differential adaptation to temperature, and temporal overlap resulted from their differential responses to algal food concentration. In the tropical Lake Jinniu, B. calyciflorus s.s. persisted throughout the year, and overlapped with B. dorcas for 5 months. Temporal overlap resulted from their differential responses to copepod predation. These results indicated that the temporal distribution pattern of cryptic B. calyciforus species and the mechanism allowing competitor coexistence vary with different climate zones.

Lung cancer is a common malignant tumor of the lung and the leading cause of cancer mortality worldwide. Non-small-cell lung cancer (NSCLC) accounts for 80%–85% of lung cancer, 40% of NSCLCs will have spread beyond the lungs by the time it is diagnosed. Long non-coding RNA (LncRNA) prostate androgen-regulated transcript 1 (PART-1) was reported that promote the development of several cancers. In the current study, we conducted experiments to investigate the role of PART-1 in the proliferation, invasion, and migration of NSCLC. The expression level of the PART-1 gene increased significantly in the NSCLC cell lines, including A549, H1229, H1650, H1975, and PC9. Knocking down of PART-1 inhibited the proliferation, invasion, and migration of A549 cells, moreover, decreased the tumor proliferation in nude mice. We confirmed that PART-1 targeted miR-204-3p directly, and miR-204-3p targeted the insulin-like growth factor binding protein 2 (IGFBP-2) directly. Furthermore, we discovered that PART-1 involved the NSCLC progression by regulating the miR-204-3p-targeted IGFBP-2 pathway. LncRNA PART-1 might be a target for treating NSCLC, and a warning sign of diagnosis of early lung cancer.

Mitochondrial alternative oxidase 1a (AOX1a) plays an extremely important role in critical node of seed viability. However, the regulatory mechanism is still poorly understood. The study aims to identify regulatory mechanisms by comparing between OsAOX1a-RNAi and wild type (WT) rice seed during artificial aging treatment. Gain weight and P50 significantly decreased in OsAOX1a-RNAi rice seed, indicating that there might be impaired in seed development and storability. Compared to WT seeds in the 100%, 90%, 80%, and 70% germination, respectively, NADH and succinate-dependent O2 consumption, the activity mitochondrial malate dehydro-genase and ATP contents were decreased in OsAOX1a-RNAi seeds in the 100%, 90%, 80%, and 70% germination, respectively, indicating that mitochondrial status in the OsAOX1a-RNAi seeds after imbibition was weaken than the WT. In addition to, the reduced abundance of complex I N and P module subunits might showed that the capacity of mitochondrial electron transfer chain was significantly inhibited in the OsAOX1a-RNAi seed at critical node of seed viability. Above results might indicated that the ATP production was impaired in OsAOX1a-RNAi seeds during ageing. Therefore, we conclude that the activities of mitochondrial metabolism and alternative pathways were severely inhibited in OsAOX1a-RNAi seeds at critical node of viability, which was leading to accelerate the collapse of seed viability. The precise regulatory mechanism of the alternative pathway at the critical node of viability still needs to be further analyzed.

Background: The role of preoperative serum carcinoembryonic antigen (sCEA) and postopeative tissue CEA (tCEA ) were widely elaborated separately for colorectal cancer (CRC). But the role of the combined sCEA and tCEA was scarcely described by now. Methods: 1757 cases of 0~ⅣCRC from January 2006 to January 2016 in our institution were involved. Clinicopathological features and follow up data were collected. 0 stage was combined into 0&Ⅰ stages. SCEA was classified to normal and high(>10ng/ml) and tCEA were classified into three grades (+,++,+++). So combined groups were six (2ⅹ3). ANOVA and Crosstab were used to analyze continuous and counting data, Univariate and multivariate were analyzed by Cox regression. All data were analyzed by SPSS27 and survival curves with number at risk were visualized by R 4.3.1. Results: Gender, age, tumor location, tumor size, blood loss, T stage, differentiation, harvested lymph nodes, positive lymph nodes, chemotherapy, TNM stage and complication have difference between the combined CEA test (all P

We report on the role of synergistic polarization of Ba0.9Sr0.1TiO3 (BST) nanoparticles in sulfur cathodes to enhance the redox kinetics of polysulfides for high-capacity Li-S batteries. Ferroelectric nanoparticles are known to significantly improve the electrochemical performance of Li-S batteries due to their inherent self-polarization and high adsorption capacity towards polysulfides. X-ray diffraction spectra confirmed the tetragonal symmetry (c/a=1.0073), while Raman spectroscopic analysis validated the presence of tetragonal orientation Raman modes in BST-modified composites. Scanning electron microscope (SEM) images showed a homogeneous distribution of BST in the sulfur cathode system, with grain sizes ranging from 1 to 1.5 μm. Notably, the BST-coupled S50BST30CB10PVDF10 composite cathode achieved a capacity of approximately 820 mAh/g at 100 mA/g, maintaining stability over 100 cycles, demonstrating improved electrochemical performance. Two distinct plateaus between 2.3 V to 2.0 V and 2.0 V to 1.5 V further underscore the superior performance of BST ferroelectric nanoparticles in enhancing the redox kinetics of Li-S batteries. By leveraging the favourable affinity of polar substances towards polysulfides, we aimed to create a more stable reactive environment within the cathodic site, effectively trapping polysulfide intermediates through the synergistic polarization of BST nanoparticles. The synergistic polarization induced by the asymmetric crystal structure of ferroelectrics is anticipated to generate internal electric fields, enhancing chemisorption with heteropolar reactive. The observed high cyclic stability further validates the efficacy of these composite cathodes in mitigating the polysulfide shuttle effect, offering promising prospects for advancing Li-S battery technology.

Cost-efficient catalyst for hydrogen evolution reaction (HER) and methanol oxidization reaction (MOR) is of great importance for industrial application. The alloying of platinum with cheap transition metal offers a great opportunity to reduce cost and enhance the electro-catalytic performance. Herein, we report a simple and green route to synthesize porous Pt-Cu catalysts, where Pt-Cu solid particles were first produced by using cuprous chloride (CuCl) nanoparticles as the template, followed by a dealloying treatment to obtain final porous product. The porous alloy nanoparticles show higher catalytic activity and superior stability for HER and methanol oxidation reaction, which is beneficial from the porous structure and synergetic effect between Pt and Cu.

This experiment was conducted to study the effects of Cyfluthrin (Cy) exposure on neurobehaviour, hippocampal tissue and synaptic plasticity in Wistar rats. First, high-dose Cy exposure can cause nerve injury with symptoms such as deficits in learning and memory ability, spatial exploration and autonomic motor ability. Moreover, it was found that medium- and high-dose Cy exposure can cause disordered energy metabolism in hippocampal cells and an abnormal release of the neurotransmitter Glu. Second, pathological brain sections showed that the middle and high doses of Cy caused deformation, reduction and disorder of hippocampal pyramidal cells, a decrease in the number of Nissl bodies, pyknosis of the hippocampal cell nuclear membrane and serious damage to organelles, indicating that exposure to these doses of Cy may cause hippocampal tissue damage in rats. Third, with the increase in exposure dose, the morphological changes in hippocampal synapses were more obvious, including blurred synaptic spaces, decreased synaptic vesicles and a decreased number of synapses. Moreover, the expression levels of the key synaptic proteins PSD-95 and SYP also decreased in a dose-dependent manner, indicating obvious synaptic damage. Finally, the study found that medium and high doses of Cy could upregulate the expression of A2AR in the hippocampus, and the expression levels of inflammatory factors and apoptosis-related proteins increased in a dose-dependent manner. Moreover, the expression of A2AR mRNA was correlated with neurobehavioural indicators, inflammatory factors, synaptic plasticity factors and apoptosis factors, suggesting that Cy may cause nerve damage in rats and has a close relationship with A2AR.

In this article, we introduce some multi-messenger studies of blazars. Main contents contain the following parts, 1. the subclasses of blazars and the observational characteristics, 2. emission variabilities from the multi-messenger observations, 3. the physical origin for the multi-messenger studies. Based on mid-IR observations collected from the $WISE$ database, we collect two sources (BZQ J1700+6830 and BZQ J1842+6809) to analyze the mid-IR variabilities. \\ (1) For BZQ J1700+6830, the period is $P\approx$ 42 hr at the four bands ($W1$, $W2$, $W3$, $W4$); for BZQ J1842+6809, the period is $P\approx$ 123 hr at the two bands ($W1$, $W2$). \\ (2) Using the periodicities, we calculate that the central black hole mass ($BH$) should be $M = (5.44\sim33.0)\times10^8M_{\odot}$ for BZQ J1700+6830 and $M = (1.13\sim6.88)\times10^9M_{\odot}$ for BZQ J1842+6809.\\ (3) For the two sources, during the flaring stage, we find anti-clockwise variation trends based on the time-based relations built by the spectral indices ($\alpha$) and flux densities ($F$).\\ (4) We calculate the Doppler factor ($\delta$) when the sources are in the dimming or brightening stages, and find that with the frequency increasing, the Doppler factor become stronger.

Initial periods of adsorption kinetics play an important role in estimating the initial adsorption rate and rate constant of adsorption process. Several adsorption processes rapidly occur, and the experimental data of adsorption kinetics under the initial periods can contain potential errors. The pseudo-second-order (PSO) kinetic model has been popularly applied in the field of adsorption. The use of the nonlinear optimization method to obtain the parameters of the PSO model can minimize error functions during modelling compared to the linear method. However, the nonlinear method has limitations in that it cannot directly recognize potential errors in the experimental points of time-dependent adsorption, especially under the initial periods. In this study, for the first time, the different linear types (Types 1–6) of the PSO model are applied to discover the error points under the initial periods. The result indicated that the fitting method using its linear equations (Types 2–5) is really helpful for identifying the error (doubtful) experimental points from the initial periods of adsorption kinetics. The imprecise points lead to low adjusted R2 (adj-R2), high reduced χ2 (red-χ2), and high Bayesian information criterion (BIC) values. After removing those points, the experimental data were adequately fitted with the PSO model. statistical analyses demonstrated that the nonlinear method must be used for modelling the PSO model because its red-χ2 and BIC were lower than the linear method. Type 1 has been extensively applied in the literature because of its very high adj-R2 (0.9999) and its excellent fitting to experimental points. However, its application should be limited because the potential errors from experimental points were not identified by this type. For comparison, the other kinetic models (i.e., pseudo-first-order, pseudo-nth-order, Avrami, and Elovich) are applied. The modelling result using the nonlinear forms of those models indicated that the fault experimental points from the initial periods were not detected.

The mangrove plant Acanthus ilicifolius and its relative, A. mollis, have been previously proved to possess diverse pharmacological effects. Therefore, evaluating the differentially expressed proteins of these species under tidal flooding stress is essential to fully exploit and benefit from their medicinal values. The roots of A. ilicifolius and A. mollis were exposed to 6 h of flooding stress per day for 10 days. The dry weight, hydrogen peroxide (H2O2) content, anatomical characteristics, carbon and energy levels, and two-dimensional electrophoresis coupled with MALDI-TOF/TOF MS technology were used to reveal the divergent flooding resistant strategies. A. ilicifolius performed better under tidal flooding stress, which was reflected in the integrity of the morphological structure, more efficient use of carbon and energy, and a higher percentage of up-regulated proteins associated with carbon and energy metabolism. A. mollis could not survive in flooding conditions for a long time, as revealed by incomplete cell structures of the roots, less efficient use of carbon and energy, and a higher percentage of down-regulated proteins associated with carbon and energy metabolism. Energy provision and flux balance played a role in the flooding tolerance of A. ilicifolius and A. mollis.

Terrestrial plant resources are becoming increasingly scarce; moreover, the development of science and technology has facilitated the exploration of marine ecosystems. We isolated and identified six novel (1–6) and six (7–12) known secondary metabolites of Alternaria sp MCCC 3A00467 by chromatographic and spectroscopic techniques and investigated their antitumor activities in human myeloma (U266), liver cancer (HepG2), and lung cancer (A549) cells by the MTT assay. Among these compounds, the new compounds 2, 3 and 4 exhibited excellent anticancer activities with IC₅₀ values of 21.98, 24.99 and 14.78 μg/mL, respectively. These compounds obtained from a marine source have the potential to be developed into novel anticancer drugs.

Fructan, a fructose polymer, is used as carbohydrate reserve in many plants. The nutritional and therapeutic benefits of fructans have attracted increasing interest by consumers and food industry. In the course of evolution, many plants have developed the ability of regulating plant frunctan metabolism genes to produce different structures and chain length fructans, which are strongly correlated with their survival in harsh environments. De nevo domestication of fructan-rich plants based on genome editing is a viable and promising approach to improve human dietary quality and reduce the risk of chronic disease. These advances will greatly facilitate breeding and production of tailor-made fructans as a healthy food ingredient from wild plants such as polygonati rhizoma. The purpose of this review is to broaden our knowledge on plant fructan biosynthesis, evolution and beneficial applications for human health.

To study the influence of electrothermal effect of ESD protection device on the reliability of inte-grated circuit,a theoretical model of ESD protection device thermal resistance is constructed in the paper based on the Conservation of Energy Principle. By analyzing the temperature relativity between electricity parameter and thermology parameter of ESD protection device characterized by self-heating thermal resistance, the quantitative relationship expression of physical parameter and geometric parameter is obtained, which can be used to improve ESD protection device elec-tro-thermal effect. The simulation testing and the real tape-out testing of ESD protection device self-heating thermal resistance based on ggNMOS are shown and compared. It is concluded that self-heating thermal resistance is an effective index for the protection device electrothermal char-acterization. Based on the established model, the self-heating thermal resistance could be decreased to improve the homogeneity of the heat transference. The uneven distribution of device temperature can be reduced, and the overall reliability of chips can be improved.

Hepatic carboxylesterase 1(CES1) metabolizes many prodrugs into active ingredients or direct-acting drugs into inactive metabolites. We aim to develop a semi-physiologically based pharmacokinetic model(Semi-PBPK model) to simultaneously predict pharmacokinetics of CES1 substrates and their active metabolites in liver cirrhosis(LC) patients. Six prodrugs(enalapril, benazepril, cilazapril, temocapril, perindopril and oseltamivir) and three direct-acting drugs (flumazenil, pethidine and remimazolam) were selected. The parameters including organ blood flows, plasma binding protein concentrations, functional liver volume, hepatic enzymatic activity, glomerular filtration rate(GFR) and gastrointestinal transit rate were introduced into the simulation. Pharmacokinetic profiles of these drugs and their active metabolites were simulated in 100 virtual subjects. The developed semi-PBPK model, following validation in healthy subjects, was extrapolated to LC patients. Most of the observations are within the 5% and 95% quantile of simulations from 100 virtual patients. The estimated AUC and Cmax are within 0.5-2-fold of observation. The sensitivity analysis showed that the decreased plasma exposure of active metabolite due to the decreased CES1 was partly attenuated by the decreased GFR. Conclusion: The developed PBPK model has successfully predicted pharmacokinetics of CES1 substrates and their metabolites in healthy subjects and LC patients, which assists in tailoring dosages of CES1 substrates in LC patients.

Extracts of Cordyceps militaris which possess the bioactive capacity such as antimicrobial activity and DPPH-free radical scavenging capacity, are applied to the serum product. This finished serum product has been evaluated the in vitro bioactivity and the stability with expect to find out a good extract with a suitable percentage used for serum product as natural materials on preservatives and antioxidation.

Two-dimensional (2D) transition metal dichalcogenides (TMDCs) nanosheets have shown extensive applications due to their excellent physical and chemical properties. However, the low light absorption efficiency limits their application in optoelectronics. By rolling up 2D TMDCs nanosheets, the one-dimensional (1D) TMDCs nanoscrolls are formed with spiral tubular structure, tunable interlayer spacing and opening ends. Due to their increased thickness of scroll structure, the light absorption is enhanced. Meanwhile, the rapid electron transportation is confined along the 1D structure. Therefore, the TMDCs nanoscrolls show improved optoelectronic performance compared to 2D nanosheets. In addition, the high specific surface area and active edge site from bending strain of basal plane make them promising materials for catalytic reaction. Thus, the TMDCs nanoscrolls have attracted intensive attention in recent years. In this review, the structure of TMDCs nanoscrolls is firstly demonstrated and followed by various preparation methods of the TMDCs nanoscrolls. Afterwards, the applications of TMDCs nanoscrolls in the fields of photodetection, hydrogen evolution reaction, and gas sensing are discussed.

Group A rotaviruses (RVA) have been identified as the leading cause of neonatal calf diarrhea (NCD) In Yunnan, China, despite the limited documentation on this issue within the country. Given the significant impact on animal health and welfare, further attention is warranted to comprehend the prevalence and epidemiology of this disease. In this study, we isolated RVA strains from NCD clinical samples to support RVA epidemic study and further disease control in Yunnan. Material and Methods: Ten fecal samples were obtained from calves with a single episode of neonate calf diarrhea from a farmer during a severe NCD outbreak. For the diagnosis of Group A rotavirus (RVA) infection, fecal reverse transcription-polymerase chain reaction (RT-PCR) was employed as the primary method. Subsequently, RVA isolation was conducted on MA104 cells, with inoculates being pretreated with trypsin TPCK to enhance viral infectivity. The isolated RVA strain was further confirmed through RT-PCR and immunofluorescence assay. Results: RVA virus was isolated from clinical samples following six passages depended on trypsin treatment of inoculates. The sign of CPE detected consisted of increased cell granularity, obscure cell boundaries, cell rounding, and eventual degeneration and detachment of cells. Analysis of sequencing revealed that field isolates was of group A serotype. Phylogenetic analysis based on the ORF sequences of the VP4 and VP7 sequences segments indicated that the isolate was classified as the P[1] genotype. VP4 gene of strain YN-1 shares 75.2%-99.7% nucleotide identity of and 81.6%–99.7% amino acid identity with the complete VP4 sequences of the P[1]. The complete VP7 gene of YN-1 is 981 nucleotide long and encode 326 amino acids. The RotaC v2.0 analysis classified the sequence as the G8 genotype. The VP7 gene of strain YN-1 shares 88.5%-97.7% nucleotide identity and 94.2%-99.1% amino acid identity. Conclusion: This is the first study in China which reports the circulation of Group A NCD on cattle farms in the field. Our study constitutes a crucial and a necessary step allowing preventive and veterinary medicine to support RVA disease controls in Yunnan province, China.

The active power-assist function greatly expands the potential applications of exoskeleton robots, yet the motion intention estimation (MIE) for active power-assist strategy is quite problematic. Through the analysis of the conduction path and the different stage manifestations of motion intention in human body, we confirmed that the joint torque of human body meets the basic requirements of MIE for the active power-assist that we suggest, namely: (i) it reflects the direction and intensity of the wearer’s efforts; (ii) it precedes the human limb motion; (iii) it generates real-time and continuous output. Thus, an online calculation method of human joint torque was proposed. The sensing system integrated in exoskeleton robots was designed to perceive motion data and foot contact force of a human body. A special inverse dynamics with a parameterized model of the human body was proposed. Contrast experiments were carried out with the motion capture system, which results’ accuracy and similarity were evaluated via the root mean square error and correlation coefficient. The comparative analysis of two synchronous results shows good accuracy of the proposed MIE method, which lays the foundation for the realization of active power-assist.

With advances in next-generation sequencing(NGS) technologies, large number of multiple types of high-throughput genomics data are available. A great challenge in exploring cancer mechanism is to identify the driver genes from the mutation genes by analyzing and integrating multi-types genomics data. Breast cancer is known as a heterogeneous disease. The identification of subtype-specific driver genes is critical to guide the diagnosis, assessment of prognosis and treatment of breast cancer. We developed an integrated frame based on gene expression profilings and copy number variation(CNV) data to identify breast cancer subtype-specific driver genes. In this frame, we employed statistical machine-learning method to select gene subsets and utilized an module-network analysis method to identify potential candidate driver genes. The final subtype-specific driver genes were acquired by paired-wise comparison in subtypes. To validate specificity of the driver genes, the gene expression data of these genes were applied to classify the patient samples with 10-fold cross validation and the enrichment analysis were also conducted on the identified driver genes. The experimental results show that the proposed integrative method can identify the potential driver genes and the classifier with these genes acquired better performance than with genes identified by other methods.