Virus infection is one of the most common etiologies of hearing loss. Hearing loss associated with viral infection can be unilateral or bilateral, mild or severe, sudden or progressive, and permanent or recoverable. Many viruses cause hearing loss in adults and children; however, the pathogenesis of hearing loss caused by viral infection is not fully understood. This review describes cytomegalovirus, the most common virus causing hearing loss, and other reported hearing loss-related viruses, along with their pathogenic characteristics and research progress on their pathology, hearing phenotypes, possible associated mechanisms, treatment and prevention measures, aiming to provide diagnostic and treatment assistance to clinical workers.

Species have shown their habital variations in responding to climate change, especially during the spring and summer spawning seasons. The species distribution model (SDM) is considered the most favorable tool to study the potential effects of climate change on species distribution. Therefore, we developed the ensemble SDM to predict the changes in species distribution of Portunus trituberculatus among different seasons in 2050 and 2100 under the climate scenarios RCP4.5 and RCP8.5. The results of SDM indicate that the distribution of this species will move northward and have obviouse seasonal variations. Meanwhile, the suitable habitat for the species will be significantly reduced in summer, with loses rates ranging from 45.23% (RCP4.5) to 88.26% (RCP.8.5) by 2100s. Habitat reduction will mainly occur in the East China Sea and southern part of the Yellow Sea, while there will be a small increase in the northern Bohai Sea. These findings will be important to manage the ecosystem and fishery, provide an information forecast of this species in the future, and maintain species diversity if the seawater temperature rises.

Looking at different operating climatic conditions, the electrical behavior predicting photovoltaic modules gets very important. For the estimation of output power from photovoltaic (PV) plants this is a very essential and basic aspect. In this paper, the relationship between the I-V curve and the irradiation spectrum is discussed by combining the single diode model. An explicit elementary analytical model with two defined shape parameters is discussed and improved with three approximations and second order Taylor expansion. Then, the explicit elementary analytical model is investigated under varying conditions leveraging the four parameters I_ph, I₀, R_s and R_sh from the single diode model. The relationship between the physical parameters and the condition parameters are discussed and applied to extract the shape parameters at different scenarios. Considering the aging effect, the process of calculation to predict the I-V curve under different splitting spectra is simplified as follow: (1) two shape parameters are gotten from the I-V data at measurement reference conditions (MRC); (2) the short circuit current, open circuit voltage and shape parameters under any splitting spectrum can be calculated based on the relationship provided in article; (3) the performance of PV panel can be predicted with parameters. The validation of this model was experimentally proven leveraging monocrystalline silicon photovoltaic module with different splitting films. Results showed that the model accurately predicts the I-V characteristics for the examined PV modules at different irradiance spectra and cell temperatures. Moreover, the presented model performs superior compared to other investigated models when looking at accuracy and simplicity.

Excessive nitrogen application has become a hidden danger threatening the sustainable development of agriculture. Exploring the potential genes will help to improve the nitrogen availability of wheat through molecular breeding. We therefore conducted wheat transcriptomics and proteomics researches under complete culture medium without nitrogen (N0) and complete culture medium with nitrogen (N1). The results showed that, the nitrogen deficit decreased the fresh weight, N content and net photosynthetic rate of winter wheat. 3949 and 2675 differentially expressed genes (DEGs) were identified in the shoot and root, respectively, while 164 and 129 differentially expressed proteins (DEPs) were identified in the shoot and root respectively. 9 genes in shoot and 26 genes in root showed the same trends in RNA and protein levels. 5 genes in shoot and 4 genes in root showed the opposite trends in RNA and protein levels. Pathway enrichment of wheat transcriptome and proteome under nitrogen deficit proposed 3 candidate genes related to photosynthesis in shoot, 4 candidate genes related to carbon metabolism in shoot, and 12 candidate genes related to carbon metabolism in root. Meanwhile, the chromosomal and subcellular localization of these genes were listed, which will provide reference for improving nitrogen availability through molecular breeding.

A novel starch stabilized Mg/Al LDHs material (S-LDH) was prepared in a facile approach and its fluoride ion removal performance was developed. Characterization of S-LDH was employed by using XRD, FTIR and particle size distribution. The adsorption property was studied through the assessment of adsorption isotherms, kinetic models, thermal dynamics and pH influence. The result shows that a low loading of starch of 10 mg onto LDH could obviously improve fluoride removal rate. The S-LDH had 3 times higher adsorption capacity to fluoride than that of Mg/Al LDH to fluoride. The particle size was smaller and the particle size distribution was narrower for S-LDH than that for Mg/Al LDH. Langmuir adsorption isotherm model and pseudo-second-order kinetic model fitted well with the experimental data. In thermodynamic parameters, the enthalpy (△H0) value was 35.63 kJ mol-1 and the entropy (△S0) value was 0.0806 kJ mol-1K-1. The values of △G0 were negative, implying the adsorption process is spontaneous. S-LDH reveals stable adsorption property in a wide pH range from 3 to 9. The mechanism for fluoride adsorption on S-LDH included surface adsorption and interaction ion exchange.

This paper first discusses a fractional-order Liu system of order as low as 2.7 and shows its chaotic characteristics by carrying out numerical simulations such as Lyapunov exponents, bifurcation diagrams and phase portraits. Then, by using the topological horseshoe theory and computer-assisted proof, the existence of chaos in the system is verified theoretically. Finally, the fractional-order system is implemented on a Field Programmable Gate Array (FPGA) and the results obtained show that the fractional-order Liu system is indeed chaotic.

Herpesvirus is a prevalent pathogen that primarily infects human epithelial cells and has the ability to reside in neurons. In the field of otolaryngology, herpesvirus infection primarily leads to hearing loss and vestibular neuritis, and is considered the primary hypothesis regarding the pathogenesis of vestibular neuritis. In this review, we provide a summary of the effects of herpes virus on cellular processes in both host cells and immune cells, with a focus on HSV-1 as illus-trative examples.

Due to the incomplete of China's current social security system, health shocks are one of the main risks faced by rural families. Using data from the 2019 China Household Finance Survey, we examined the impact of borrowing on household welfare when rural households face health shocks. We found that household income and food expenditure both declined significantly when rural households faced health shocks; rural household borrowing was mainly used for the treatment of the diseases, and it had a crowding out effect on tourism and general health care expenditures, but not on education expenditures. We also found that the impact of borrowing on the western region was higher than that on the central and eastern regions from Looking at the impact of borrowing in different regions. Finally, we put forward some suggestions for promoting sustainable rural development from the perspective of medical security, such as accelerating the promotion of new rural medical insurance, helping rural low-income families improve health benefits, establishing diversified financing channels, improving rural financial platforms, and solving the financing difficulties of households to improve the ability of rural households to resist health shocks.

In order to address the issue of nutrient deficiency in coconut coir-based nursery substrates, three materials with nutrient supplementation effects, namely pig manure, composted rice husks, and agricultural humic acid, were added in equal volumes to the coir-based substrate. The newly formulated substrates were then tested for their seedling growth effects on cucumber and rice. Results indicate that the substrate formulation consisting of "10% pig manure + 30% peat + 50% coconut coir + 10% vermiculite" was capable of satisfying the growth requirements of both cucumber and rice seedlings, with the highest acceptance among farmers.

This paper focuses on the effect of malondialdehyde-induced oxidative modification (MiOM) on the gel properties of duck myofibrillar proteins (DMPs). DMPs were first prepared and treated with oxidative modification at different concentrations of malondialdehyde (0, 0.5, 2.5, 5.0 and 10.0 mmol/L). The physicochemical changes (carbonyl and free thiol group content) and gel properties (gel whiteness, gel strength, water holding capacity, rheological properties and mi-cro-structural properties) were then investigated. The results showed that the content of protein carbonyl groups increased with increasing MDA oxidation (P<0.05), while the content of free thiol groups decreased significantly (P<0.05). Meanwhile, there was a significant trend of decrease in gel whiteness; the hardness and water-holding capacity of protein gels increased significantly under the oxidation of low concentration of MDA (0-5 mmol/L), while the hardness of gels decreased under the oxidation of high concentration (10 mM). The storage modulus and loss modulus of oxidized DMPs also increased with increasing concentration; moreover, microstructural analysis confirmed that the gels oxidized at low concentrations were more compact and homogeneous in terms of pore size compared to the high concentration or blank group. In conclusion, moderate oxidation of malondialdehyde was beneficial to improve the gel properties of duck; however, excessive oxidation was detrimental to the formation of dense structured gels.

Based on the dynamic strength variation mechanism of concrete under complex loading conditions, two approaches were devised: numerical testing and CT scanning, guided by the principle of minimizing energy dissipation. A methodology for calculating concrete's failure area and measuring its strength was developed. The analysis delves into the mechanisms behind failure patterns and variations in concrete specimen strength, focusing on crack initiation, development, and the resultant failure surface formed by crack propagation, along with the stress distribution in concrete specimens subjected to diverse loading conditions. Through evaluating the strength and computed failure area of concrete specimens, it is evident that the loading method influences both the strength and failure area of concrete specimens. In general, a larger failure area correlates with a higher measured strength.

Polymer adhesives have emerged as a promising dielectric passivation layer in hybrid bonding for 3D integration while they raise misalignment problems during curing. In this work, the synergistic effect of oxygen plasma surface activation and wetting is utilized to achieve bonding between completed cured polyimides. The optimized process achieves a void-less bonding with a maximum shear strength of 35.3 MPa at a low temperature of 250 °C in merely 2 min, significantly shortening the bonding period and decreasing thermal stress. It is found that the plasma activation generated hydrophilic groups on the polyimide surface, and the wetting process further introduced more -OH groups and water molecular on the activated polyimide surface. The synergistic process of plasma activation and wetting facilitate bridging polyimide interfaces to achieve bonding, providing an alternative path for adhesive bonding in 3D integration.

The statistical technique, the multiple regression model, is employed to analyze the relationship between the dependent variable and several independent variables. The multicollinearity problem is one of the assumptions in the multiple regression model that occurred in the relationship among independent variables. The ordinal least square is the standard method to evaluate parameters in the regression model, but the multicollinearity problem affects the unstable estimator. The Liu regression is proposed to approximate the Liu estimators based on the Liu parameter to overcome multicollinearity. For this paper, we have proposed the modified Liu parameter to estimate the biasing parameter in scaling options to compare the ordinal least square estimator with two modified Liu parameters and six standard Liu parameters. The performance of the modified Liu parameter is considered with the generating independent variables from the multivariate normal distribution in the Toeplitz correlation pattern as the multicollinearity data, where the dependent variable is obtained from the independent variable multiplied with a coefficient of regression and with the error from the normal distribution. The mean absolute percentage error is computed as an evaluation criterion of estimation. For application, the Hepatitis C patients dataset is a real dataset to investigate the benefit of the modified Liu parameter. Through the simulation and real dataset, it can be seen from the results that the modified Liu parameter outperforms the other Liu parameters and the ordinal least square estimator. It can recommend the user for estimating parameters by using the modified Liu parameter when the independent variable exits the multicollinearity problem.

The study of the currently known >3,000 species of snakes can provide valuable insights into the evolution of their genomes. Deinagkistrodon acutus, also known as Sharp-nosed Pit Viper, one hundred-pacer viper or five-pacer viper, is a venomous snake with significant economic, medicinal and scientific importance. Widely distributed in southeastern China and South-East Asia, D. acutus has been primarily studied for its venom. Here, we employed next-generation sequencing to assemble and annotate a highly continuous genome of D. acutus. The genome size is 1.46 Gb; its scaffold N50 length is 6.21 Mb, the repeat content is 42.81%, and 24,402 functional genes were annotated. This study helps to further understand and utilize D. acutus and its venom at the genetic level.

Cellobiose phosphorylase (CBP) catalyzes the reversible phosphorolysis of cellobiose into α-glucose 1-phosphate and glucose. When it was used in transforming cellulose to amylose (PNAS, 110: 7182-7187, 2013) as well as in constructing a yeast with the ability to phosphorolytically use cellodextrin to produce ethanol, a CBP with a broadened substrate specificity would be more desirable. Based on the structure differences in the catalytic loops of CBP and cellodextrin phosphorylase from Clostridium thermocellum (named CtCBP and CtCDP, respectively), CtCBP was mutated. A single-site mutant S497G was identified to have a 5.7-fold higher catalytic efficiency with cellotriose as a substrate in phosphorolytic reaction direction compared to wild type, without any loss of catalytic efficiency on its natural substrate cellobiose. When S497G variant was used in the transformation of mixed cellodextrin (cellobiose + cellotriose) to amylose, a significant increase in amylose yield was achieved compared to that of wild type CtCBP. Structure change in the substrate binding pocket of S497G variant accounted for its capacity to accept longer cellodextrins than cellobiose. Taken together, S497G variant of CtCBP was confirmed to acquire a promising feature favorable to those application scenarios involving cellodextrin’s phosphorolysis.

To achieve a micro-destructive and rapid measurement of the wood density of standing trees, this study investigated the feasibility of using the micro-drilling resistance method, formulated a mathematical model, explored the potential for a unified model across multiple tree species, and analyzed the influence of moisture content on measurement accuracy. First, 231 tree cores and drill resistance data were sampled from Pinus massoniana, Cunninghamia lanceolate, and Cryptomeria fortunei. The basic density and moisture content of each core were measured, and the average value of each resistance data record was calculated. Second, the average drill resistance, the natural logarithm of average drill resistance, and absolute moisture content were used as independent variables, while the wood basic density was used as the dependent variable. Third, the total model of the three tree species and sub-model for each tree species were established through a stepwise regression method. Finally, the accuracy of each model was compared and analyzed with that of using the average basic density of each tree species as an estimated density. The results revealed that the estimation accuracy of the sub-model for each tree species was 1.670 percentage points higher than the average value of each tree species used as the density estimation value for these tree species. Additionally, except for Cryptomeria fortunei, the natural logarithm of drill resistance significantly influenced the wood density model at a significance level of 0.05. Moreover, moisture content significantly affected the total model and sub-models of Pinus massoniana at a significance level of 0.05. The estimation accuracy of the total mathematical model was 2.125 percentage points lower than that achieved using the average basic density of each tree species to predict their density. The results indicated the feasibility of using the micro-drilling resistance method to measure the wood density of standing trees. Moreover, the relationship between wood density and drill resistance did not follow a linear pattern, and moisture content slightly influenced the drill needle resistance. Furthermore, the establishment of a mathematical model for each tree species was deemed essential. This study provides valuable guidance for measuring the wood density of standing trees through the micro-drilling resistance method.

This study aimed to overcome the difficulty of conducting the horizontal-well cavity leaching test in the field and to investigate the long-term stability of the horizontal-well salt-cavity natural gas storage. The simulation test design is combined with the similarity theory to study the cavity expansion characteristics and the influence law of cavity leaching parameters. Through the design of a rubber hose connection, an integrated closed test system for multi-stage horizontal-well cavity leaching and brine drainage was built. The test system also realises the repeatable backward movement of the injection well during the test. A similarity simulation of the test design was carried out, and the test platform was constructed to carry out multi-stage horizontal-well leaching tests with a nitrogen cushion. In the horizontal-well leaching tests with a nitrogen cushion, the influence laws of the well spacing, flow rate and liquid level position on cavity expansion were investigated. Based on the morphological characteristics of the horizontal-well cavity, a numerical model of the horizontal-well salt cavity was developed, which reflects the real cavity morphology leached in the test. The long-term stability of the horizontal-well salt-cavity natural gas storage under different internal pressures was investigated through numerical simulation.

Wool quality and yield are important economic traits of livestock. In this study, the skin tissues of the upper scapula of Super Merino sheep (SM) and Small-Tailed Han sheep (STH) during the growing period were studied. Differentially expressed (DE) long non-coding RNAs (lncRNAs) and messenger RNAs (mRNA) were identified via histopathological observation and high-throughput RNA sequencing. Gene ontology (GO) and the Kyoto Encyclopedia of Genes and Genomes (KEGG) were used to analyze differentially expressed genes. Reverse transcription quantitative Polymerase Chain Reaction (RT-qPCR) was used to verify nine selected DE lncRNAs and five DE mRNAs. Significant differences were found in the expression levels of LOC114113396 (KRTAP15-1), CRABP1, KRT10, KRTAP1-3, KRTAP4.3, KRT2, FGF1, IGF-1, and KIT in SM and STH skin tissues. These results indicate that these mRNAs may play an important role in the growth and development of hair follicles and the regulation of hair fiber traits. Differentially expressed lncRNA target genes and mRNAs were mainly enriched in biological processes and pathways related to skin development and fiber traits, which is consistent with previous studies. LncRNA MSTRG.9225.1, MSTRG.124320.1, MSTRG.96951.1, MSTRG.91685.1, MSTRG.122229.1, MSTRG.89255.1, MSTRG.98769.1, and MSTRG.84658.1 may indirectly participate in the growth and development of sheep hair follicles and the regulation of hair fiber diameter by regulating the expression of their respective target genes. These candidate lncRNAs and mRNAs may provide a basis for the study of sheep hair follicle growth and development and hair fiber traits.

In order to study the strength changes of concrete specimens under different loading conditions, based on the principle of minimum energy dissipation and from the Angle of concrete failure energy per unit area, the finite element numerical simulation software was applied to concrete specimens with different failure modes of tension, compression, bending and torsion, and the double-broken line damage constitutive model was adopted to simulate and analyze the failure forms of concrete specimens under different loading conditions. The failure area and failure energy of each specimen during loading were quantitatively calculated under each failure mode, and the relationship between the failure area and failure energy consumed under different failure modes was analyzed. The results show that under different failure modes, the failure area of concrete specimens is different, the energy consumed during failure is different, and the strength is different. However, in the process of failure, no matter how the failure mode changes, the failure energy W per unit area remains unchanged and is a constant, which is related to the physical properties of concrete itself.

Cytomegalovirus infection contributes to 10-30% congenital hearing loss in children. Vertebrate peripheral auditory organs include the outer, middle and inner ear. Their development is regulated by multiple signaling pathways. However, most ear diseases due to viral infections are due to congenital infections and reactivation, and affect healthy adults to a lesser extent. This may be due to the fact that viral infections affect signaling pathways that are important for the development of peripheral hearing organs. Therefore, an in-depth understanding of the relationship between viral infections and the signaling pathways involved in the development of peripheral hearing organs is important for the prevention and treatment of ear diseases. In this review, we summaries the effects of viruses on signaling pathways and signaling molecules in development of peripheral auditory organ, with a focus on Human cytomegalovirus as an example.

Single-phase-to-ground fault in non-effectively grounded systems poses serious public safety concern. Along with increasing deployment of low-voltage (LV) sensors, new opportunities and ways are created for solving this traditional problem in distribution systems. A new approach, identifying primary single-phase-to-ground line fault and locating it through measurement data from smart sensors deployed in the secondary side of distribution transformers, is proposed in this paper. When a fault occurs in primary distribution feeder, the transient aerial mode voltage (AMV) of each LV smart sensor is calculated. The fault line can be identified by an abrupt change value of AMV at LV side. Next, by finding the position of the maximum value of this AMV from LV sensors on the fault line, the fault location can be pinpointed to two neighboring distribution transformers. The proposed method has been proven to be efficient and reliable by simulation studies.

Street view images can help us better understand the city environment and potential characteristics. With the development of computer vision and deep learning, the technology of semantic segmentation algorithms has become more mature. However, DeeplabV3+, which is commonly used in semantic segmentation, has shortcomings such as a large number of parameters, high requirements for computing resources, and easy loss of detailed information. Therefore, this paper proposes LM-DeeplabV3+, which aims to greatly reduce parameters and computations of the model while ensuring the segmentation accuracy. Firstly, the lightweight network MobileNetV2 is selected as the backbone network, and the ECA attention mechanism is introduced after MobileNetV2 extracts shallow features to improve the ability of feature representation; secondly, the ASPP module is improved, and on its basis, the EPSA attention mechanism is introduced to achieve cross-dimensional channel attention and important feature interaction; thirdly, a loss function named CL loss is designed to balance the training offset of multiple categories and better indicate the segmentation quality. This paper conducted experimental verification on the Cityspaces dataset, and the results showed that the mIoU reached 74.9%, which was an improvement of 3.56% compared to DeeplabV3+; the mPA reached 83.01%, which was an improvement of 2.53% compared to DeeplabV3+.

In an effort to enhance the efficiency and safety of open-pit mines, this study explores the optimization of end slope road parameters and slope structures, specifically focusing on unmanned driving lanes.A significant aspect of the study is the development of a truck trajectory offset model, which considers the different reaction times between automated sensors and human drivers in adapting to environmental changes. To test these concepts, the study uses numerical simulations to confirm the stability of the proposed end slope designs. Using Victory West Mine No. 1 as a case study, the research determines the optimized width for unmanned driving lanes and the maximum angle for safe steepening of end slopes. The findings indicate that the optimized unmanned lane width for NTE240 mining dump trucks is 1743 mm, allowing for a 2-degree increase in the slope angle at the south end slope. This optimization leads to a steep mining stripping volume of 3.2735 million m³ and a coal output of 2.49628 million tons, maintaining a stripping ratio of 1.31m³/t. These results demonstrate that the unmanned driving road width optimization not only ensures slope safety but also significantly boosts the economic benefits of steep mining in open-pit mines.

Ammonium sulfate has been utilized in agriculture; however, there is a dearth of research on its application in maize cultivation subsequent to the implementation of nitrification inhibitors or coating. This study aims to analyze the impacts of various combinations of ammonium sulfate fertilizers on soil nutrients, plant nutrient uptake, yield, and fertilizer utilization efficiency in maize cultivation to ascertain the optimal and stabilized disposal method for ammonium sulfate. A completely randomized design was employed with five treatments (AU, the control using urea; AS, treatment using ammonium sulfate; ASN, treatment using ammonium sulfate with a nitrification inhibitor; ASG, treatment using oil-coated ammonium sulfate; ASD, treatment using oil-humic acid-coated ammonium sulfate). Results showed that: (1) Compared with AU and AS, ASN, ASG and ASD decreased the leaching rates of TN, NH4+-N and NO3-N to the 10-20 cm soil layer, and more residual N was obtained in 0-10 cm soil layer. The first-order kinetic equation Nt=N0(1-e-kt) can better fit the process of nitrogen accumulation and release, and the N release rate constant is AU>CK>AS>ASH>ASN>ASD; (2) Compared with AU and AS treatments, the plant dry weight, grain dry weight, spike width, spike length, and yields of maize increased by 8.85-11.08%, 12.98-14.15%, 2.95-3.52%, 5.50-5.65%, and 43.21-51.10% under ASG treatment respectively. The impact of effective spike number on maize yield was found to be significant, as demonstrated by the path analysis conducted in this study. Furthermore, the accumulation levels of nitrogen, phosphorus, and potassium within above-ground plants significantly increased under the ASG treatment compared to the AU and AS treatments. The partial productivity of nitrogen, phosphorus, and potassium increased by 1.43-1.51-fold under ASG treatment, while grain nitrogen balance, grain phosphorus balance, and grain potassium balance increased by 1.41-1.58-fold, 1.51-1.95-fold, and 1.15-l.96-fold respectively. The oil-coated ammonium sulfate, therefore, exhibited the optimal slow-release effect of nutrients, thereby achieving superior performance in enhancing maize production and efficiency.

This research seeks to advance the understanding of ecological management in the Huaihe River Basin, China. The spatiotemporal variability of the Normalized Difference Vegetation Index (NDVI) and its underlying driving forces are examined utilizing SPOT-NDVI data covering the period 2000-2019. Linear regression analysis is employed to quantify trends and assess the statistical significance of NDVI variations. A differencing approach is subsequently applied to discern the variability in NDVI. The distribution of its spatial pattern stability over 20 years is explored through the coefficient of variation. Lastly, the Geodetector method is utilized to elucidate the driving factors influencing NDVI dynamics. The results indicate that the overall NDVI is generally high, with an overall growth rate of 0.00148/year, and 2010 is identified as a significant inflection point in the trend. NDVI values are notably lower in urban areas, corresponding to urban expansion, except for regions near rivers and lakes. Land use type emerges as the strongest explanatory factor for NDVI among single factors, with climate factors exhibiting a relatively weaker degree of explanatory force. These findings suggest that the overall NDVI in the Huaihe River Basin is high, indicative of a vegetation condition that continues to improve.

Corneal opacity is a leading cause of vision impairment and suffering worldwide. Transplantation can effectively restore vision and reduce chronic discomfort. However, there is a considerable shortage of viable corneal graft tissues. Tissue engineering may address this issue by advancing xeno- keratoplasty as a viable alternative to conventional keratoplasty. In particular, livestock decellularization strategies offer the potential to generate bioartificial ocular prosthetics in sufficient supply to match existing and projected needs. To this end, we have examined the best practices and characterizations that have supported the current state-of-the-art driving preclinical and clinical applications. Identifying the challenges that delimit activities to supplement the donor corneal pool derived from acellular scaffolds allowed us to hypothesize a model for keratoprosthesis applications derived from livestock combining 3D printing and decellularization.

The tourism economy plays an essential role in supporting and driving tourism development. Therefore, studying its resilience is crucial for promoting sustainable and high-quality tourism development. Based on the core essentials of economic toughness, this paper constructs the tourism economic toughness evaluation index system, uses the entropy weight TOPSIS method to measure the tourism economic toughness of 10 counties and cities in the Yili River Valley in 2010-2019, analyzes its spatio-temporal evolution characteristics through the standard deviation ellipse, the traditional Markov chain, and the spatial Markov chain, and uses the grey correlation analysis method to analyze the driving factors of the tourism economic toughness. The results show that: (1) the economic resilience of tourism in the Yili River Valley shows a "W"-shaped time-series dynamic development trend with an average index of 0.28394, in which it experienced a decline from 0.28 to 0.27 during 2012-2013 and 2015-2016; (2) Spatial Pattern: The Yili River Valley tourism economic resilience is characterized by a clear uneven spatial distribution. The city of Yining, representing the northwestern region, exhibits a high level of resilience, while the southwestern region, endowed with rich tourism resources, demonstrates a medium level of resilience. Conversely, the central to southeastern counties and cities, such as ChabuchaerXibo Autonomous County and other counties and cities, are characterized by a lack of developed tourism facilities, which has resulted in a lower level of resilience and a weak development situation; (3) In terms of spatial and temporal evolution, the standard deviation ellipse is stabilized year by year pointing to "northwest-southeast", the clustering tendency is gradually enhanced, and five tourism economic resilience convergence clubs are identified, whose internal transition probability is significantly affected by spatial location, and which show obvious stability and neighborhood effects; (4) Regarding the driving factors, the impact of each driving factor on the resilience of the tourism economy reaches the statistical significance threshold of 0.77 or above. Among them, the number of employees in the tertiary industry, especially the input of high-quality talents in the tourism industry, plays a key role in improving the quality of tourism services and strengthening the industry's ability to withstand risks and development potential.

Abstract: Image aesthetic assessment (IAA) with neural attention has made significant progress due to its effectiveness in object recognition. Current studies have shown that the features learned by convolutional neural networks (CNN) at different learning stages indicate meaningful information. The shallow feature contains the low-level information of images and the deep feature perceives the image semantics and themes. Inspired by this, we propose a visual enhancement network with feature fusion (FF-VEN). It consists of two sub-modules, the visual enhancement module (VE module) and the shallow and deep feature fusion module (SDFF module). The former uses an adaptive filter in the spatial domain to simulate human eyes according to the region of interest (ROI) extracted by neural feedback. The latter not only takes out the shallow feature and the deep feature by transverse connection, but also uses a feature fusion unit (FFU) to fuse the pooled features together with the aim of information contribution maximization. Experiments on standard AVA dataset and Photo.net dataset show the effectiveness of FF-VEN.

The ongoing revolution in Deep Learning is redefining the nature of computing that is driven by the increasing amount of pattern classification and cognitive tasks. Specialized digital hardware for deep learning still holds its predominance due to the flexibility offered by the software implementation and maturity of algorithms. However, it is being increasingly desired that cognitive computing occurs at the edge, i.e. on hand-held devices that are energy constrained, which is energy prohibitive when employing digital von Neumann architectures. Recent explorations in digital neuromorphic hardware have shown promise, but offer low neurosynaptic density needed for scaling to applications such as intelligent cognitive assistants (ICA). Large-scale integration of nanoscale emerging memory devices with Complementary Metal Oxide Semiconductor (CMOS) mixed-signal integrated circuits can herald a new generation of Neuromorphic computers that will transcend the von Neumann bottleneck for cognitive computing tasks. Such hybrid Neuromorphic System-on-a-chip (NeuSoC) architectures promise machine learning capability at chip-scale form factor, and several orders of magnitude improvement in energy efficiency. Practical demonstration of such architectures has been limited as performance of emerging memory devices falls short of the expected behavior from the idealized memristor-based analog synapses, or weights, and novel machine learning algorithms are needed to take advantage of the device behavior. In this work, we review the challenges involved and present a pathway to realize ultra-low-power mixed-signal NeuSoC, from device arrays and circuits to spike-based deep learning algorithms, with ‘brain-like’ energy-efficiency.

Z-ligustilide is a main active ingredient in the volatile oil of Angelica sinensis, a traditional Chinese medicine. Cisplatin is a commonly used chemotherapy drug for the treatment of lung cancer. Efficacy is often limited by the development of drug resistance after long-term treatment. Here, we investigated the effect of the combination of Z-ligustilide and cisplatin (Z-ligustilide+cisplatin) on resistance of cisplatin-resistant lung cancer cells and its action mechanism. Cell viability was analyzed by cell counting kit-8 (CCK-8) assay. Cell cycle and cell apoptosis were examined by flow cytometry assay. mRNA and protein levels of factors related to cell cycle and apoptosis were analyzed by real-time PCR and western blot. Liquid chromatography-mass spectrometry (LC-MS) analysis and RNA sequencing in A549, A549/DDP and A549/DDP cells treated with the Z-ligustilide+cisplatin were performed. The expression of PLPP1 was analyzed by the Cancer Genome Atlas (TCGA). The correlation between PLPP1 and prognosis was evaluated by immunohistochemistry and Kaplan-Meier (KM) plotter analysis. We found that Z-ligustilide+cisplatin could decrease the cell viability of cisplatin-resistant lung cancer cells. Z-ligustilide+cisplatin induced cell cycle arrest, and promoted cell apoptosis of cisplatin-resistant lung cancer cells. Metabolomics combined with transcriptomics revealed that Z-ligustilide+cisplatin inhibited phospholipid synthesis by upregulating the expression of PLPP1. Furthermore, PLPP1 expression was positively correlated with good prognosis. Knockdown of PLPP1 abolished the effects of Z-ligustilide+cisplatin on cell cycle and apoptosis. Z-ligustilide+cisplatin inhibited the activation of AKT by reducing the levels of PIP3 levels. Z-ligustilide+cisplatin induced cell cycle arrest and promoted cell apoptosis of cisplatin-resistant lung cancer cells by inhibiting PLPP1-mediated phospholipid synthesis.

The study of underwater vehicle wake detection is of significant importance within the field of target detection, localisation and tracking of underwater vehicles. Given that propellers are the propellers of modern ships and underwater vehicles, the propeller wake field represents the principal target source for wake detection in underwater vehicles. The objective of this paper is to propose a method for measuring the wake of an underwater propeller based on a position-sensitive detector. A theoretical model of the relationship between the laser spot displacement and the change of refractive index of the wake field is established on the basis of the principle of laser beam deflection. A prototype experimental setup for underwater propeller wake measurement was constructed based on the aforementioned optical measurement method. Furthermore, the simulation of the propeller wake flow field with strong density stratification and linear density stratification was conducted based on the experimental setup. In the experiment, a three-bladed propeller with a diameter of 39mm was selected, the water tank size was 980mm×380mm×380mm, and the laser acted at a distance of 550 mm from the propeller. The experimental results indicate that the wake dissipation time of the propeller in a strong density-stratified water environment is approximately 800s. Following the stabilization of the wake field density, the laser spot position is observed to be stable at 0.341 mm, with a corresponding refractive index change of 2.99×10-6 RIU. The wake dissipation time of the propeller in a linear density-stratified water environment is approximately 750 s. Once the wake field density has reached a stable state, the laser spot position is found to be 0.441mm, corresponding to a refractive index change of 3.87×10-6 RIU. These experimental results are found to be in general agreement with the simulation results of the propeller wake field. A comparison of the experimental device-based wake measurements with the CTD-based wake measurements reveals a consistent trend.

In this paper, a novel permanent magnet-assisted synchronous reluctance machine (PMASynRM) with rare-earth PMs and ferrite magnets is proposed. The performance of PMASynRM is discussed with respected to the different magnet ratio of rare-earth PMs and ferrite magnets. Some characteristics including the flux density, output torque, cogging torque, output power, power factor, torque ripple, loss, efficiency, and demagnetization are calculated by 2-D finite element analysis (FEA). The analysis results show that the excellent performance can be obtained by using hybrid magnet of rare-earth PMs and ferrite magnets with the suitable magnet ratio, and provide some desirable cost-performance trade-off.

The refractive index of seawater is one of the essential parameters in ocean observation, so it is necessary to achieve high precision seawater refractive index measurement. In this paper, we propose a method for measuring the refractive index of seawater based on a Position Sensitive Detector (PSD). Theoretical model is established to depict the correlation between laser spot displacement and refractive index change, utilizing a combination of position sensitive detector and laser beam deflection principle. Based on this optical measurement method, a seawater refractive index measurement system was established. To effectively enhance the sensitivity of refractive index detection, a focusing lens was incorporated into the optical path of the measuring system, and simulations were conducted to investigate the impact of focal length on refractive index sensitivity. The calibration experiment of the measuring system was performed based on the relationship between refractive index of seawater and underwater pressure (depth). By measuring laser spot displacement at different depths, changes in displacement with respect to both refractive index and depth were determined. Experimental results demonstrate that the system exhibits a sensitivity of 9.9277×10−9RIU (refractive index unit), the refractive index deviation due to stability is calculated as ±7.545×10−9RIU. Thereby the feasibility of highly sensitive measurement of seawater refractive index is verified.

In the era of big data with increasingly complex data structures and ever-larger data scales, matrix-type data are becoming highly valued and their applications in the fields of medicine, industry, education, geography, and astronomy are growing in extent. In recent years, significant progress has been made in the practical use of matrix variable t-distribution finite mixture models for handling data in order to address the issues of multi-subgroup structures and long data tails. In this paper, the expectation-maximization (EM) algorithm with penalized maximum likelihood is proposed to resolve the problem of the unbounded nature of the likelihood function applied to the model by considering the degeneracy of the variance-covariance matrix of this model. Our data were analyzed through simulations and real data, and the results demonstrate that our model is effective in both preventing the likelihood function from being unbounded and in ensuring the accuracy of the estimated parameters of the EM algorithm.

Rapid and accurate detection of road cracks is of great significance for road health monitoring, but currently this work is mainly completed through manual site surveys. Low-altitude UAV remote sensing can obtain images with centimeter or even subcentimeter ground resolution, which provides a new efficient and economical approach for rapid crack detection. Nevertheless, crack detection networks face challenges such as edge blurring and misidentification due to the heterogeneity of road cracks and the complexity of the background. To address these issues, we propose a real-time edge reconstruction crack detection network (ERNet) which adopts multi-level information aggregation to reconstruct crack edges and improve the accuracy of segmentation between the target and background. To capture global dependencies across spatial and channel levels, we propose an efficient bilateral decomposed convolutional attention module (BDAM) that combines depth separable convolution and dilated convolution to capture global dependencies across spatial and channel levels. To enhance the accuracy of crack detection, we use a coordinate-based fusion module that integrates spatial, semantic, and edge reconstruction information. In addition, we propose an automatic measurement of crack information for extracting the crack trunk and its corresponding length and width. Experimental results demonstrate that our network achieves the best balance between accuracy and inference speed.

In order to solve the problem of the poor oil displacement effect of high molecular weight alkali/surfactant/polymer (ASP) solution in low permeability reservoirs, Daqing Oilfield uses a partial quality tool to improve the oil displacement effect in low permeability reservoirs. Without changing the oil displacement capability of high molecular weight ASP solution in high permeability oil layers, the ASP solution is actively sheared in low permeability oil layers by using a partial quality tool to increase the injection capability of the solution and improve the overall oil recovery. In order to study the ability of the partial quality tool to improve the oil displacement effect, firstly, the matching degree of high molecular weight ASP solution to low permeability cores is studied, and the ability of quality control tools to change the molecular weight is studied. Then, experimental research on the pressure and oil displacement effect of high molecular weight ASP solution before and after the actions of the partial quality tool is carried out. The results show that ASP solutions with molecular weights of 1900 × 104 and 2500 × 104 have a poor oil displacement effect in low permeability reservoirs. After the action of the partial quality tool, the injection pressure is reduced by 5.22 MPa, and the oil recovery is increased by 7.79%. The injection pressure of the ASP solution after shearing by the partial quality tool is lower than that of the ASP solution with the same molecular weight and concentration without shearing, but the oil recovery is lower. On the whole, the use of the partial quality tool can obviously improve the oil displacement effect in low permeability reservoirs.

Determining the general-name-derived semantic relationships between geographic names often requires consulting many geographic name documents for verification. In geographic name translation and geographic name knowledge graphs, this method cannot meet the needs of large-scale extraction of general-name-derived semantic relationships between geographic entities. To solve this problem, this paper proposes a general-name derivation relation recognition method based on Prompt learning and Semantic Spatiotemporal Distribution Attention Feature Fusion (SSD-AFF). This method adopts a pipe-based relationship recognition strategy. First, the Prompt learning method is adopted to form a general-name derivation pattern with the general-name-derived geographical name category and the original geographical name category as the prompt word, and then the derivation pattern is combined with the geographical name as the input of the model so that the recognition problem of the general-name derivation of the geographical name can be transformed into a classification problem using the bidirectional language model. Then, by analyzing the characteristics of the semantic association and geographical spatio-temporal distribution between the general-name-derived geographical name and the original geographical name, the semantic spatio-temporal distribution characteristics of the general-name-derived geographical name are constructed. Finally, the network model based on the semantic spatio-temporal distribution Attention Feature Fusion (SSD-AFF) is used to distinguish the general-name-derived semantic relationships. The experimental results show that the proposed method has good performance. It can effectively mine the general-name-derived semantic relations between the vector data of geographical entities and has important application value in geographical name translation and geographical name knowledge maps.

In view of the limitations of the existing optimization method of suspender cable force, in order to improve the stress of suspender under completion state and avoid frequent adjustment of cable force and grid beam elevation during construction, a new method of cable force optimization is proposed. The article takes the longest large span arch bridge in the world, Pingnan Third Bridge, a Concrete-filled steel tube (CFST) arch bridge with a span of 575m as the engineering background combined with the finite element analysis and multi-objective optimization method. One cable force optimization method that suspender “Real-time correction during construction, in the process variable optimal and results reliable” during panel girder lifting of long span CFST arch bridges is clarified. Taking the panel girder weight and displacement during the construction as parameter variables, the displacement and unevenness of the panel girder under completion state as constraint conditions, the displacement and cable force during the hoisting construction as the objective equation, through the optimization of the objective equation, the suspender cable force and dis-placement of each hoisting section are calculated. The results show that it is feasible to introduce the optimization theory into the cable force optimization when lifting the panel girder. the segment displacement variation is minimized to meet the destination. The cable force distributed evenly under completion state of the bridge that further making sure the completion state satisfies the requirements. No repeating iteration is needed, thus avoiding cumberso me calculation, getting cable force once. With higher optimization efficiency and better effects, the method provides high value for the cable force calculation of same type bridge suspender construction and for guiding construction.

Short video addiction refers to a psychological dependency on short video applications, characterized by an intense attachment and an inability to control usage, leading to typical addiction symptoms. While its definition bears similarities to substance addiction, significant differences also exist. According to the Diagnostic and Statistical Manual of Mental Disorders, Fifth Edition (DSM-5), published in 2013, short video addiction has not yet been officially classified as an addiction disorder. To facilitate more in-depth and standardized research on short video addiction, it is essential to synthesize and organize existing studies on its theoretical foundations and mechanisms.

Practical applications of CsPbX3 nanocrystals (NCs) are limited by their poor stability. The formation of heterojunction between CsPbX3 NCs and oxides is an effective means to protect perovskite from polar solvents and other external factors. Significantly improving the stability and photocatalytic properties of the core/shell perovskite is very important for its application in photoelectric and photocatalytic technology. Here, we report the synthesis of asymmetrical CsPbBr3/TiO2 core-shell heterostructure NCs at single particle level by hot injection liquid phase synthesis and sol-gel method, where each CsPbBr3 NCs is partially covered by titanium dioxide. It is shown that the type II arrangement is generated at the heterogeneous interface, which greatly facilitates the separation of electron-hole pairs and increases the carrier transport efficiency. More crucial, due to the protection of titanium dioxide shell, the product has higher long-term stability in humid air compared with bare CsPbBr3 NCs. The asymmetrical core-shell heterostructure prepared in this study not only improves the stability of CsPbX3 NCs, but also provides some ideas for optoelectronic device applications and TiO2-based photocatalysts.

The general circuit topology and principles of low-noise high-voltage power supply are investigated to meet the requirements of the high-voltage bias application in air kerma meters. Two topologies, flyback converter and Royer converter are simulated using SPICE simulation program. The simulation results indicate that the circuit structure of the Royer converter is more complex, but it obtains lower output high voltage noise. While we develop an adjustable high-voltage power supply according to the circuit structure of the Royer converter, and tested it to ensure the design requirements for continuously adjustable output high-voltage linearity. The test results show that the linear adjustment rate is not more than ±0.0025%, the load regulation rate is less than ±0.1%, and the output ripple noise voltage percentage is less than 0.01%. These tested performance make it more suitable for accurate nuclear measurements.

Accurate evaluation of patients with disorders of consciousness (DoC) is crucial for personalized treatment. However, misdiagnosis remains a serious issue. Neuroimaging methods could observe the conscious activity in patients who have no evidence of consciousness in behavior, and provide objective and quantitative indexes to assist doctors in their diagnosis. In the review, we discussed the current research based on the evaluation of consciousness rehabilitation after DoC using EEG, fMRI, PET, and fNIRS, as well as the advantages and limitations of each method. Nowadays single-modal neuroimaging can no longer meet the researchers` demand. Considering both spatial and temporal resolution, recent studies have attempted to focus on the multi-modal method which can enhance the capability of neuroimaging methods in the evaluation of DoC. As neuroimaging devices become wireless, integrated, and portable, multi-modal neuroimaging methods will drive new advancements in brain science research.

The metro station ridership features are associated significantly with the built environment factors of the pedestrian catchment area surrounding metro stations. The existing studies have focused on the impact on total ridership at metro stations, ignoring the impact on varying patterns of metro station ridership. Therefore, the reasonable identification of metro station categories and built environment factors affecting the varying patterns of ridership in different categories of stations is very important for metro construction. In this study, we developed a data-driven framework to examine the relationship between varying patterns of metro station ridership and built environment factors in these areas. By leveraging smart card data, we extracted the dynamic characteristics of ridership and utilized hierarchical clustering and K-means clustering to identify diverse patterns of metro station ridership, and finally identified six main ridership patterns. We then developed a new built environment measurement framework and adopted multinomial logistic regression analysis to explore the association between ridership patterns and built environment factors. (1) The clustering analysis result revealed that six station types were classified based on varying patterns of passenger flow, representing distinct functional characteristics. (2) The regression analysis indicated that diversity, density, and location factors were significantly associated with most station function types, while destination accessibility was only positively associated with employment-oriented type station, and centrality was only associated with employment-oriented hybrid type station. These results could inform the coordinated development of rail transit and land use, and the renewal and enhancement of the built environment in the pedestrian catchment area surrounding metro stations.

Researches on the runoff and sediment reduction effects of soil and water conservation measures are being on the rise, which is of great significance for carrying out strategic on soil and water conservation in the Yellow River Basin. Through the analysis of various soil and water conserva-tion measures, runoff, sediment, and rainfall datas in the Sanchuan River Basin from 1960 to 2019, we use the lagrange multiplier method to determining the threshold year of soil and water con-servation measures on runoff and sediment processes. The preliminary conclusion is as follows: The trend of flood season rainfall and annual rainfall in the Sanchuan River Basin is consistent. The 10-year average rainfall in each periods indicates that before 2000, it gradually decreased and then significantly increased. The 10-year average runoff showed a gradual decrease before 2010, followed by a sudden increase, while the 10-year average sediment has shown a decreasing trend years by years, especially after the centralized treatment period. Terrace and dam measures show a trend of first decreasing, then increasing, and then approaching stability during different treat-ment periods, while the trend of forest and grass measures is slightly decreasing and then in-creasing rapidly. The runoff and sediment reduction effects of various soil and water conservation measures during different treatment periods indicate that the runoff reduction effect reached its peak in 2005, while the sediment reduction benefit reached its best in 2015. Based on the compre-hensive benefits of runoff and sediment regulation, 2015 are considered as the threshold year for various soil and water conservation measures, with each measure areas being 4.86 × 104, 17.91 × 104, 1.20 × 104, and 0.83 × 104hm2, respectively. The research results will have certain reference significance for the high-quality development of soil and water conservation in the Yellow River Basin.

Edvard Munch, a founder of Expressionism was pre-occupied with depicting his subjective experience and the most prolific painter of self-portraits since Rembrandt. Based on evidence that faces and self-related images are more salient than other objects it is plausible that self-portraits, in which the subject and object are the same, reflect the artist’s state of mind. Although he suffered from a variety of physical and psychological illness Munch was not diagnosed with any specificity in his lifetime. Posthumous diagnoses include schizophrenia, anxiety, bipolar and other disorders. Recent research has revealed altered visual perception in such patients. The present study empirically analysed three stylistic elements of Munch’s painted self-portraits and portraits: contrast, colour and fractal dimension and his painted productivity, to determine if variations correlate with critical life events and if so whether they indicate states of mind. It found significant increases in contrast and colour brightness and persistent high complexity during critical periods supporting the conclusion that Munch is diagnostically best described as suffering from early onset schizophrenia and comorbid social anxiety disorder.

Many have speculated that events of personal and financial loss in Rembrandt’s life caused depression and that this is revealed by examination of his self-portraits particularly those painted in old age. Some report detecting various physiological diseases associated with aging, including vision impairment, which may have affected his mood and work. Aging and neurodegenerative disease which often accompanies it, are both associated with depression. Recent advances in imaging and computer technology make it possible to empirically examine changes in artistic style which can contribute to understanding artists’ physical and mental health. In the current study changes in contrast, colour and fractal dimension were measured in the entire corpus of Rembrandt’s painted self-portraits and portraits to determine whether changes in style indicate depression or disease. Productivity was also examined as an indirect indicator. Given the high salience attributed to self-images, it also examined whether differences in style could be detected between self-portraits and portraits of related and unrelated others. The results indicate that it is unlikely that Rembrandt suffered from unipolar or bipolar depression, age-related cognitive decline, or neurodegenerative disease. The data are consistent with someone experiencing episodes of low mood consistent with normal grieving and adversity followed by resilient recovery. There is evidence of a gradient in saliency and complexity between self-portraits and related and unrelated portraits, of a less formal style in portraits of related others and of a ‘late’ style identified by leading art historians consistent with macular degeneration. The results are also consistent with an association of aesthetic preference with mid-level fractal values tending towards the Golden Mean long associated with beauty in nature and in art.

The task of weakly supervised point cloud semantic segmentation has received widespread attention and also has been widely used in autonomous driving, robotics, and modern industries. Due to the high dimensionality and large volume of point cloud data, many technical difficulties appeal to weakly supervised semantic processing, especially segmentation. However, weakly-supervised schemes usually provide only partial labelling information of the underlying point cloud data and thus need to effectively extract local features, geometric information, and contextual relationships only using these limited labelled data for supervised learning. To improve weakly-supervised semantic segmentation, we propose a novel segmentation network through the boundary-based feature aggregation based on a K-NN algorithm with down-sampling operation, and also introduce the smoothness loss and Siamese loss for effective segmentation. The experiments on public datasets demonstrate that our presented segmentation method exceeds most of the existing fully supervised and weakly-supervised methods in terms of mIoU. Specifically, our network has high segmentation accuracy on the labels of objects with similar geometrical structures, such as ceiling, wall, floor, chair and table, reaching 91.2%, 98.8%, 83.3%, 75.3% and 80.2%, respectively. Extensive experiments also illustrate its robustness, effectiveness, and generalization of the proposed weakly supervised segmentation network.

The majority of existing numerical simulations of the effect of bridge piers on water movement are based on a limited number of bridge piers at a laboratory scale. Furthermore, some 2D numerical simulations for actual bridge projects have deficiencies, including the use of overly large mesh sizes and an inadequate treatment of bridge piers. In this study, we compare three methods of structural mesh encryption, suspension mesh, and nonstructural mesh based on Delft3D, and apply the optimization scheme to a real bridge project. It is demonstrated that optimal results can be achieved by utilising a grid size comparable to the pier diameter (Dp) in the region away from the piers. In the vicinity of the piers, the grid cell size should be no larger than 1/9 Dp. The suspended grid technique (DD Boundary) can yield results consistent with those obtained using a full-area high-resolution grid, provided that the total number of grids can be reduced and the computational time is considerably reduced. In this study, the unstructured mesh (Deflt3D Flexible Mesh) scheme was unable to capture the oscillations of the wake flow behind the bridge piers. However, the application of the optimized scheme in bridge engineering has demonstrated its practical value. The findings of this study on mesh resolution and suspension mesh scheme can be applied to the Delft3D software and are also useful for other numerical simulation work.

Underwater robots often encounter the influence of confined underwater environments during underwater exploration. These environments include underwater caves, sunken ships, submerged houses, and pipeline structures. Robot positioning in these environments is strongly disturbed, leading not only to the failure of some commonly used positioning methods but also to an increase in errors in positioning systems that normally function well in open water. In order to overcome the limitations of positioning methods in underwater confined environments, researchers have studied different underwater positioning methods and selected suitable methods for positioning in such environments. These methods can achieve high-precision positioning without relying on assistance from other platforms, and are referred to as autonomous positioning methods. Autonomous positioning methods for underwater robots mainly include SINS/DR positioning and SLAM positioning. In addition, in recent years, researchers have also developed some bio-inspired autonomous positioning methods. This article introduces the applicable robot positioning methods and sensors in underwater confined environments and discusses the research directions of robot positioning methods in such environments.

Concrete is more stable than filler as a false roof in a downward approach type infill quarry, but the mechanical model of a concrete false roof is not clear. As a result, there has been limited application. Therefore, it is necessary to establish the mechanical model of a concrete artificial false roof to enhance the stability of the downward approach infill quarry. This paper combines theoretical analysis, model derivation, finite element analysis and field application methods. Firstly, the basic assumptions of thin plate theory and elasticity mechanics are used as the premise to establish the differential equations of the deflection curve of the concrete thin plate false roof. Then, the three types of bending moment generation of the concrete thin plate false roof are explored. Secondly, the relationship between the location of dangerous surface and dangerous point in hard-supported weak-slab structure and soft-supported weak-slab structure is analyzed, and the type of uniform load and calculation model of concrete thin-slab false roof are improved. Finally, according to the established mechanical model of thin slab false roof, finite element analysis and field application were carried out. The results show that there are three types of deflection curve differential equations in the concrete thin slab false roof perpendicular to the strike, and three extreme points exist in the middle section of the thin slab and on both sides of the surrounding rock. The hazardous surface of the hard-supported weak-slab structure is present at the intersection of the encircling rock and the thin-slab fake ceiling, with the perilous point situated on the top of this surface. The hazardous surface of the soft-supported weak-slab structure can be found in the centre section of the thin-slab fake ceiling, with the perilous point being located at the bottom of this surface. Moreover, the damage mode for both structures is that of maximum tensile stress damage. Upon conducting a finite element analysis, the results indicate that the concrete's maximum tensile stress is significantly high.

This paper addresses the input coupling problem for the shape memory alloy (SMA) actuated parallel platform with completely unknown nonlinear dynamics. The problem means that in a parallel platform with multiple SMA actuators acting together, the displacement of one of the actuators will simultaneously affect the remaining actuators to change. Due to the coupling problem and nonlinear characteristics of the SMA actuators, it is not easy to control the platform to achieve bi-directional swing with completely unknown nonlinear dynamics. Therefore, a model-free adaptive sliding mode control method is proposed to improve the control accuracy of the complex motion of the platform, avoiding the complex modeling process of the SMA actuated parallel platform. Based on the model-free adaptive control (MFAC) theory, a multiple input and multiple output (MIMO) dynamic linearized mathematical model of the parallel platform is established using the online input and output data of the system. Then, a sliding mode controller is designed based on the dynamic model. A rigorous theoretical analysis proves that the proposed model-free adaptive sliding mode controller is able to stably control the SMA actuated parallel platform, and its tracking error is uniformly ultimately bounded (UUB). Finally, experiments are conducted on the established SMA actuated parallel platform. The results show that the proposed model-free controller is feasible and effective, and can control the system well to achieve the complex motion of bi-directional swing.

Aiming at the problems of inaccurate segmentation of long object and information loss of small object in real-time semantic segmentation algorithm, this paper proposes a lightweight multi-branch real-time semantic segmentation network based on BiseNetV2. The new auxiliary branch makes full use of spatial details and context information to cover the long object in the field of view. Meanwhile, in order to ensure the inference speed of the model, the asymmetric convolution is used in each stage of the auxiliary branch to design a structure with low computational complexity. In the multi-branch fusion stage, the alignment and fusion module is designed to provide guidance information for deep and shallow feature mapping, so as to make up for the problem of feature misalignment in the fusion of information at different scales, and thus reduce the loss of small target information. In order to further improve the model’s awareness of key information, a global context module is designed to capture the most important features in the input data. The proposed network uses NVIDIA GeForce RTX 3080 Laptop GPU experiment, on the road street view data set Cityscapes and CamVid average occurring simultaneously ratio reached 77.1% and 78.4% respectively, with running speed of 127 frames/s respectively and 112 frames/s. The experimental results show that the proposed algorithm can achieve real-time segmentation and improve the accuracy significantly, showing good semantic segmentation performance

In this paper, we study the well-posedness and asymptotics of a one-dimensional thermoelastic laminated beam system either with or without structural damping, where the heat conduction is given by Fourier's law effective in the rotation angle displacements. We show that the system is well-posed by using Lumer-Philips theorem, and prove that the system is exponentially stable if and only if the wave speeds are equal, by using the perturbed energy method and Gearhart-Herbst-Prüss-Huang theorem. Furthermore, we show that the system with structural damping is polynomially stable provided that the wave speeds are not equal, by using the second-order energy method.

In this study, based on a new quantum integral identity, the authors establish some quantum estimates of Hermite-Hadamard type inequalities for convex functions. These results generalize and improve some known results given in literatures.

Currently, in some domestic and foreign mines, the backfill drilling pipeline experience a rupture phenomenon even when the wear degree is low. This results in a delay in production due to the filling becoming 'sick'. This paper presents, for the first time, the damage mechanism from a mechanical perspective and re-derives the anti-extrusion strength model of the backfill drilling pipeline. We investigate the influence of law on the anti-extrusion strength of pipelines from the perspective of stratum and cement ring. We then verify the theoretical and simulation results through engineering examples. The results demonstrate that the Mises stress criterion is a suitable modification principle for the anti-extrusion strength model of the backfill drilling pipeline. The anti-extrusion strength of the pipeline is related to the elastic modulus and Poisson's ratio of the stratum, and the thickness of the cement ring. It is negatively affected by the depth of the stratum. For hard strata, a cement ring with a smaller elastic modulus is suitable, while for soft stratum, a cement ring with a larger elastic modulus is recommended. When the missing angle of the cement ring is less than 60°, the stress concentration factor increases up to 2.2. The stress unloading capacity of the cement ring ranges from 32.7% to 37.8%, and optimal performance of the cement ring is achieved when it has high strength and low rigidity. The backfill filling pipeline of a copper mine abroad was destroyed due to external extrusion force exceeding its anti-extrusion strength value. The modified pipeline anti-extrusion strength model is 18.2% higher than the casing API strength value. This finding can inform the design of the backfill filling pipeline for China's kilometer-deep wells in the future.

: This study explores the perceptions of Chinese learners in Spain regarding the use of social networks for informal Spanish language learning. The objective is to identify the challenges and benefits of using social networks to address the real needs of students in learning Spanish. A qualitative phenomenological approach was adopted, focusing on participants’ perceptions before and after using social networks. Eight Chinese students were selected for the study. The study was conducted in Valencia and Barcelona, Spain, from 1 September 2023 to 20 March 2024, and three commonly used social media networks were compared. The results indicate positive perceptions towards social media as a tool for learning Spanish, highlighting its usefulness in improving language skills and enhancing cultural awareness. Additionally, Xiaohongshu and Bilibili emerged as the most popular platforms for Spanish language learning among Chinese students. This study concludes that social media effectively meets the authentic needs of Chinese students learning Spanish in Spain, enhancing both language skills and cultural adaptation. This multifaceted approach reflects the complexity of learning Spanish in the digital age, combining personal passion, professional aspirations, and cultural adaptation needs.

The aim of this study was to investigate the biochemical properties and gel-forming capacity of duck myofibrillar proteins under the effects of 2,2'-azobis (2-amidinopropane) dihydrochloride (AAPH)-mediated oxidation. Duck myofibrillar proteins were extracted and treated with different concentrations of AAPH solutions (0, 1, 3, 5, 10 mmol/L) and then analysed for carbonyl content, dynamic rheology, protein profiles and gel-forming properties (colour, water holding capacity, hardness, protein profile, microstructure). The results showed that with increasing AAPH concentration, the carbonyl content of protein showed an increasing trend (p &lt; 0.05); SDS-PAGE pattern results indicated that moderate oxidation (3 mmol/L AAPH) induced myosin aggregation via covalent bonds including disulfide, enhanced protein-protein, and thus improved protein-water interactions and gel strength of DMPs heat-induced gels. However, high oxidation (5 and 10 mmol/L AAPH) led to partial degradation of myosin heavy chain (MHC), as evidenced by lower storage modulus and irregular microstructure, which significantly reduced gelation ability. These results suggest that the internal relationship between alkanoperoxy radical-induced oxidation should be taken into account in the processing of duck meat, as mild protein oxidation is conducive to improving gel quality.

The teaching and learning environment have changed significantly over the last decade with the integration of an increasing amount of information and communication technologies, especially in distance education due to global pandemics, total lockdowns, isolation, and quarantine periods. The number of numerous virtual and non-virtual tools involved in educational processes is growing day by day. In terms of technological innovations used in learning environments, many researchers and educators are trying their best to bring more creative ideas into the technology- based learning environments. Although higher educational institutions have greatly benefited from the growing number of hardware and software resources in the educational process, they have also faced some setbacks that have harmed the learning processes. These technologies have in turn complicated some of the processes in the learning atmosphere. Therefore, we take Spanish teaching course as an example to present the challenging smarter teaching and learning systems that higher educational institutions face today.

In this paper, we consider a fourth-order suspension bridge equation with nonlinear damping term |u_t|^m-2u_t and source term |u|^p-2u. We give necessary and sufficient condition for global existence and energy decay results without considering the relation between m and p. Moreover, when p>m, we give sufficient condition for finite time blow-up of solutions. The lower bound of the blow-up time T_max is also established. It worth to mention that our obtained results extend the recent results of Wang (J. Math. Anal. Appl., 2014) to the nonlinear damping case.

Four Chinese herbs Zhishi, Zhiqiao, Qingpi and Chenpi from Citrus genus were widely used for treating various cardiovascular and gastrointestinal diseases. Although many pharmacological functions of these herb decoctions can be clarified from the bioactivities of identified ingredients, some of them remain confusing. To clarify the reasons of those confusing functions, depending on the extended structure-activity relationships of cholinergic and anti-cholinergic agents, here a simple method for quickly discovering possible choline analogs was established using a specific TLC method, and then stachydrine and choline were first identified from these Citrus herb decoctions based on their NMR and HRMS data. After this, two TLCS methods were first established respectively for the quantitatively analyses of stachydrine and choline, and the contents of both two ingredients and synephrine in 39 samples were determined using the valid TLCS and HPLC methods, respectively. The results showed the contents of stachydrine were 2.4 times to those of synephrine in Zhiqiao while about 1/3 to 2/3 in Zhishi, Qingpi and Chenpi. Simultaneously, the contents of stachydrine, choline and synephrine in these herbs present similar changing trends along with the delay of harvest time. However, the contents of synephrine decrease most rapidly, while those of stachydrine decrease most slowly. Based on these above, comparing with the pharmacological activities and pharmacokinetics reported of stachydrine and synephrine, it indicated that stachydrine and synephrine can be considered as a pair of bioactive equilibrists, especially in the cardio-cerebrovascular protection from these citrus herbs. Simultaneously, it confirmed that stachydrine should play an important role in the pharmacological functions, especially in dual-directionally regulating the uterus and various beneficial effects on cardio-cerebrovascular system, kidney and liver, of these citrus herbs.

It has been empirically observed that the upper tail of the firm size distribution follows either the Pareto distribution or the Zipf distribution, with both patterns being explained by Gibrat’s law (Gabaix, 1999). This article analyzed firm revenue data from China, spanning from 2005 to 2013, to examine the whole range of the firm size distribution. Our empirical analysis revealed that firm revenue data over these years is well fitted by a three-parameter generalized Pareto distribution, with the fitted parameters indicating a dichotomy: The size distribution of large-sized firms, namely the upper tail, is asymptotically characterized by a Pareto distribution or a Zipf distribution, whereas the size distribution of smaller and medium-sized firms is approximated by an exponential distribution. This finding suggests that Gibrat’s law should be extended to account for the emergence of a generalized Pareto distribution.

There are rich proper noun derivative semantic relationships in geographic entity vector data. The identification of traditional proper noun derivative semantic relationships usually requires toponym researchers to examine the source of derived toponyms by consulting a large number of toponym documents. This method cannot adapt to the mining of proper noun derivative semantic relationships for large-scale geographical entity. In this regard, this paper proposes a method of identifying the proper noun derivative semantic relationships for geographical entity by combining prompt learning and XGBoost model. This method transforms the extraction problem of proper noun derivative semantic relationships into a binary classification problem by analyzing the characteristics of the derivation relationship of toponyms in the form of toponyms and the spatial and temporal distribution of geography. Firstly, prompt learning and gaussian mixture model are used to extract and cluster the derivation words of toponyms, so as to realize the recognition of derived toponyms collections. Then, enumerate the possible proper noun derivations in the toponym set, and then the XGBoost model is used to identify the semantic relations derived from the proper noun of geographical entities. In the experiment, the recognition method of proper noun derivative semantic relationships based on prompt learning and XGBoost proposed in this paper has achieved good relationship recognition effect in the experiment. This method has certain practical value in the fields of toponym management and toponym translation.

System-of-systems (SoS) evolution is a complex and unpredictable process. Although various principles to facilitate collaborative SoS evolution have been proposed, there is a lack of experimental data validating their effectiveness. To address these issues, we present an Agent-Based Model (ABM) for SoS evolution in the Internet of Vehicles (IoV) , serving as a quantitative analysis tool for SoS research. By integrating multiple complex and rational behaviors of individuals, we aim to simulate real-world scenarios as accurately as possible. To simulate the SoS evolution process, our model employs multiple agents with autonomous interactions and incorporates external environmental variables. Furthermore, we propose three evaluation metrics: evolutionary time, degree of variation, and evolutionary cost, to assess the performance of SoS evolution. Our study demonstrates that enhanced information transparency significantly improves the evolutionary performance of distributed SoS. Conversely, the adoption of uniform standards only brings limited performance enhancement to distributed SoSs. Although our proposed model has limitations, it stands out from other approaches that utilize Agent-Based Modeling to analyze SoS theories. Our model focuses on realistic problem contexts and simulates realistic interaction behaviors. This study enhances the comprehension of SoS evolution processes and provides valuable insights for the formulation of effective evolutionary strategies.

This study aimed to investigate the incidence of Esox lucius with bacterial septicemia in five fish ponds of Xinjiang, China. We analyzed the water quality of each fish pond as well as the clinical symptoms and pathological changes of fish with bacterial septicemia. Furthermore, we isolated and identified pathogenic bacteria from the liver, spleen, and kidney of the infected fish based on morphology and physiology, as well as using biochemical and molecular biology techniques. By detecting the water quality of the infected fish pond, the clinical symptoms and pathological changes of the infected fish were observed, pathogenic bacteria were isolated and purified from the liver, spleen, and kidney of the died illness fish. the pathogenicity of pathogenic bacteria was identified by morphology, physiology, biochemistry, and molecular biology, and the drug sensitivity of 16 antibiotics was studied by standard Kirby–Bauer disk diffusion method. The results showed that bacterial septicemia of Esox lucius occurred in water with high levels of ammonia nitrogen, nitrates, pH, total alkalinity, and total hardness, mainly caused by the mixed infection of Aeromonas hydrophila, Aeromonas veronii and Aeromonas sobria. A rapid multiplex PCR method for the detection of pathogenic Aeromonas hydrophila was established. The isolates were sensitive to enrofloxacin, flufenicol, and doxycycline and resistant to penicillin and neomycin. This study laid a foundation for the early prediction, warning, rapid diagnosis, and effective prevention and control of bacterial septicemia.

In this paper, we propose an unsupervised blind restoration model for images in hybrid degradation scenes. The proposed model encodes the content information and degradation information of images and then uses the attention module to disentangle the two kinds of information. It can improve the ability of disentangled presentation learning for a generative adversarial network (GAN) to restore the images in hybrid degradation scenes, enhance the detailed features of restored image and remove the artifact combining the adversarial loss, cycle-consistency loss, and perception loss. The experimental results on the DIV2K dataset and medical images show that the proposed method outperforms existing unsupervised image restoration algorithms in terms of peak signal-to-noise ratio (PSNR), structural similarity (SSIM), and subjective visual evaluation.

Current numerical methods for simulating biophysical processes in aquatic environments are typically constructed in a grid-based Eulerian framework or as an individual-based model in a particle-based Lagrangian framework. Often, the biogeochemical processes and physical (hydrodynamic) processes occur at different time and space scales, and changes in biological processes do not affect the hydrodynamic conditions. Therefore, it is possible to develop an alternative strategy to grid-based approaches for linking hydrodynamic and biogeochemical models that can significantly improve computational efficiency for this type of linked biophysical model. In this work, we utilize a new technique which links hydrodynamic effects and biological processes through a property-carrying particle model (PCPM) in a Lagrangian/Eulerian framework. The model is tested in idealized cases and its utility is demonstrated in a practical application to Sandusky Bay. Results show the integration of Lagrangian and Eulerian approaches allows for a natural coupling of mass transport (represented by particle movements and random walk) and biological processes in water columns which is described by a nutrient-phytoplankton-zooplankton-detritus (NPZD) biological model. This method is far more efficient than traditional tracer based Eulerian biophysical models for 3-D simulation, particularly for a large domain and/or ensemble simulations.

Promoting green development has become an important way to optimize the ecological and economic structure and promote sustainable development. The Yangtze River Economic Belt is an important economic corridor in China, and it remains to be examined whether the implementation of environmental regulations has enhanced the green total factor productivity (GTFP) of cities. This paper calculates the green total factor productivity of 107 cities within the Yangtze River Economic Belt by using the super-efficient SBM model and the GML index with Chinese city panel data from 2007-2019 and measures the intensity of environmental regulations through textual analysis. The bidirectional fixed-effects model constructed in this paper suggests an inverted U-shaped relationship between environmental regulation and GTFP, which is confirmed by a series of robustness tests. Green technology innovation and advanced industrial structure play a mechanism role in this. In regions with lower levels of green technology and industrial structure, the inverted U-shaped relationship between environmental regulation and green total factor productivity is more significant. In addition, the phenomenon of GTFP rising and then falling because of environmental regulation is more obvious in cities in the middle and upper reaches of the Yangtze River and outside the urban agglomerations. Therefore, when formulating environmental regulation policies, it is necessary to balance the relationship between economic development and environmental protection and harmonize the environment and economic development of the entire Yangtze River Basin.

To realize the utilization of peanut shell, this study investigates the combustion behavior, chemical kinetics, and thermodynamic parameters of peanut shell using TGA under atmospheric air. Results indicate that increasing the heating rate leads to higher ignition, burnout, and peak temperatures, as observed in the TG/DTG curves shifting to the right. Analysis of combustion performance parameters suggest that higher heating rates can enhance combustion performances. Kinetic analysis using two model-free methods, KAS and FWO, shows that the activation energy (Eα) ranges from 93.30 to 109.65 kJ/mol for FWO and 89.72 to 103.88 kJ/mol for KAS. The data fit well with coefficient of determination values (R2) close to 1. Pre-exponential factors using FWO range from 2.19×106 to 8.06×107 s–1, and for KAS range from9.72×105 to 2.25×107 s–1. Thermodynamic analysis indicates a low-energy barrier (≤ ±6 kJ/mol) between activation energy and enthalpy changes, suggesting easy reaction initiation. Furthermore, variations in enthalpy (ΔH), Gibbs free energy (ΔG), and entropy (ΔS) upon conversion (α) suggest that peanut shell combustion is endothermic and non-spontaneous, with the generation of more homogeneous or well-ordered products as combustion progresses. These findings offer a theoretical basis and data support for the further utilization of agricultural biomass.

Agricultural activities are the second largest source of greenhouse gas emissions, and carbon emissions from agricultural land use (CEALU) have become a hot issue across the world. However, few scholars explored the impact of agricultural land policies on carbon emissions, such as the High-standard farmland construction(HSFC) in China.Thus，by relying on provincial panel data for China for the period 2005-2017, the effect of the high-standard basic farmland construction policy on carbon emissions from agricultural land use per unit area and its regional differences were quantitatively analyzed using the difference-in-difference (DID) model. The results showed that: 1) China's CEALU per unit area presented a fluctuating upward trend during the period 2005-2017, from 392.58 kg/ha to 457.72 kg/ha, with an average annual growth rate of 1.31%. 2) The high-standard farmland construction(HSFC) policy produced a significant carbon emission reduction effect in agricultural land use, and reduced the CEALU per unit area by 10.80% on average. With the promotion of this policy, its carbon emission reduction effect in agricultural land use presented an overall increasing trend. 3) The carbon emission reduction effect of the high-standard farmland construction policy in agricultural land use was significant in central China, but non-significant in eastern China and western China.

Selenium nanoparticles (SeNPs) has higher bioavailability and safety than inorganic selenium, and was widely used in medical, agricultural, nutritional supplements, and antibacterial fields. The present study screened a strain L11 producing SeNPs from a selenium rich dairy cow breeding base in Hubei Province, China. The strain was identified as Bacillus subtilis through physiological, biochemical, and molecular biology analysis. Through optimization of cultivation conditions, the optimal cultivation parameters for L11 to produce SeNPs were pH=6, cultivation temperature of 37 °C, 4 mmol/L Na2SeO3, and cultivation for 48 hours. XPS, SEM-EDS, and TEM were used to verify that the Se particles produced by L11 are SeNPs with diameters ranging from 50 to 200 nm. The combination of protein analysis of different cell components and TEM analysis showed that L11 mainly produces SeNPs through the transformation of the cell's periplasmic space, cell membrane, and cell wall. Adding L11 SeNPs complex to sheep feed can significantly enhance the antioxidant activity and immunity of sheep, and increase the Se content in the neck muscles, liver, and spleen tissues.

Taiwan’s auditors have suffered from processing excessive audit data, including drawing audit evidence. This study advances sampling techniques by integrating machine learning with sampling. This machine learning integration helps avoid sampling bias, keep randomness and variability, and target the risker samples. We first apply a Naive Bayes classifier to classify data into some classes. Next, a user-based, item-based, or hybrid approach is employed to draw audit evidence. The representativeness index is the primary metric for measuring the representativeness of audit evidence. The user-based approach denotes the selection of samples between two percentiles in a class as audit evidence. It may be equivalent to a combination of monetary and variable sampling methods. The item-based approach represents the choice of risky samples as audit evidence. It may be identical to a combination of non-statistical and monetary sampling methods. Auditors can hybridize those user-based and item-based approaches to balance representativeness and riskiness in selecting audit evidence. Three experiments show that sampling using machine learning integration has the benefits of drawing unbiased samples, handling complex patterns, correlations, and unstructured data, and improving efficiency in sampling big data. However, the limitations are the classification accuracy output by machine learning algorithms and the range of prior probabilities.

Mulberry leaves, when infected by pathogens, can suffer significant yield loss or even death if early disease detection and timely spraying are not performed. To enhance the detection performance of mulberry leaf diseases in natural environments and to precisely locate early small lesions, we propose a high-precision, high-efficiency disease detection algorithm named YOLOv8-RFMD. Based on improvements to You Only Look Once version 8 (YOLOv8), we first proposed the Multi Dimension Feature Attention (MDFA) module, which integrates important features at the pixel-level, spatial and channel dimensions. Building on this, we designed the RFMD Module, which consists of the Conv-BatchNomalization-SiLU (CBS) module, Receptive-Field Coordinated Attention (RFCA) Conv, and MDFA, replacing the Bottleneck in the model’s Residual block. We then employed Adown down sampling structure to reduce the model size and computational complexity. Finally, to improve the detection precision of small lesion features, we replaced the complete intersection over union (CIOU) loss function with the Normalized Wasserstein Distance (NWD) loss function. Results show that the YOLOv8-RFMD model achieves an mAP50 of 94.3% and an mAP50:95 of 67.8% on experimental data, representing increases of 2.9% and 4.3% respectively compared to the original model. The model size is reduced by 0.53 MB to just 5.45 MB, and the number of floating-point operations is reduced by 0.3 G to only 7.8 G. The improved model meets the deployment requirements of mobile embedded devices and can provide a theoretical reference for the automated spraying operations of mulberry leaves.

Inflammatory reaction after ischemia-reperfusion contributes significantly to prognosis, and microglia activation is the main resource of inflammation in nervous system. STAT5 is proving to be a highly effective anti-inflammatory therapy with great potential, and inhibition of STAT5 has demonstrated significant anti-inflammation and therapeutic effects, but rarely focus on mechanism of neuroinflammation and brain injury from ischemia-reperfusion. It is the first time to found that the anti-inflammation of dauricine is mainly through STAT5-NF-κB pathway, might act as a STAT5 inhibitor. Dauricine suppressed the inflammation cytokines Eotaxin, KC, TNF-α, IL-1α, IL-1β, IL-6, IL-12β, IL-17α, and also inhibited the microglia activation. STAT5b mutant at Tyr-699 reversed the protective effect of dauricine on oxygen-glucose deprivation-reperfusion injury of neurons, and reactivated the suppression of dauricine on P-NF-κB of microglia. These results suggest that dauricine might suppress the neuroinflammation and protect the neuron from the injury of post-ischemia-reperfusion via mediating the microglia activation through STAT5-NF-κB pathway, and ss a potential therapeutic target for neuroinflammation, STAT5 needs to be raised concern in ischemic stroke.

The refractive index of seawater is one of the essential parameters in ocean observation, so it is necessary to achieve high-precision seawater refractive index measurements. A seawater refractive index measurement system based on position-sensitive detectors is an effective means to achieve high-precision measurement of seawater refractive index. However, in the actual seawater refractive index measurement process, the impact of the measurement error caused by the jitter signal obtained from the measurement on the measurement results cannot be ignored. In this paper, we theoretically analyse the causes of the long jitter signals during seawater refractive index measurement and quantify the influencing factors. Through the analysis, it can be seen that the angle between the two windows in the refractive index measurement area of seawater causes a great error on the measurement results, so the angle between the two windows should be controlled within 2.06° in order to effectively reduce the measurement error. At the same time, the factors affecting the measurement accuracy of the position-sensitive detector are analysed, and the factors leading to the reduction of the measurement accuracy of the position-sensitive detector are mainly the background light, the size of the photosensitive surface, and the change of the temperature of the working environment. For the above factors, we add a narrow-band filter with a bandwidth of 0.9nm in front of the photosensitive surface of the position-sensitive detector during the construction of the measurement system, so as to filter out stray light other than the signal light source. On the premise of ensuring the measuring range of the refractive index of seawater, a position-sensitive detector with a photosensitive surface size of 4 mm×4 mm was selected. In order to reduce the temperature variation of the working environment of the position-sensitive detector, the measurement system was partitioned. In order to validate the testing error range of the optimised test system, standard seawater samples under the same conditions were measured. It can be seen that the jitter signal of the measurement system has been reduced from 0.0022mm before the optimisation to 0.0011mm after the optimisation, and the deviation of the refractive index has been reduced by 1.09×10−8RIU. The experimental results show that the refractive index of seawater has been effectively reduced by adjusting the optical path and the structure of the seawater refractive index measurement system.

Laser scanning 3D imaging technology, because it can get accurate three-dimensional surface data, has been widely used in the search for wrecks and rescue operations, underwater resource development, and other fields. At present, the conventional underwater rotating laser scanning imaging system maintains a relatively fixed light window. However, in low-light situations underwater, the rotation of the scanning device causes some degree of water fluctuation, which warps the light strip data that the system sensor receives about the object's surface. To solve the problem, this research studies an underwater 3D scanning and imaging system that makes use of a fixed-light window and a spinning laser (FWLS). A refraction error compensation algorithm is investigated that is based on the fundamentals of linear laser scanning imaging and the dynamic refraction mathematical model is established by the motion of the imaging device. During the imaging process, the incident angle between the laser and the light window varies due to the scanning mode of the system. The experimental results show that the reconstruction radius error is reduced by 60% (from 2.5 mm to about 1 mm) when the measurement data for a standard sphere with a radius of 20 mm are compensated. Moreover, the compensated point cloud data exhibits a higher degree of correspondence with the model of the standard spherical point cloud. This study has a specific reference value for the refractive error analysis of an underwater laser scanning imaging system, and it provides certain research ideas for the subsequent refractive error analysis of various scanning imaging modalities.

In this paper, we study the semilinear pseudo-parabolic equations $\displaystyle u_{t} - \triangle_{\mathbb{B}}u - \triangle_{\mathbb{B}}u_{t} = \left|u\right|^{p-1}u$ on a manifold with conical singularity, where $\triangle _{\mathbb{B}}$ is Fuchsian type Laplace operator investigated with totally characteristic degeneracy on the boundary $x_{1} = 0$. Firstly, we discuss the invariant sets and the vacuum isolating behavior of solutions with the help of a family of potential wells. Then, we derive a threshold result of existence and nonexistence of global weak solution: for the low initial energy $J(u_{0})<d$, the solution is global in time with $I(u_{0}) >0$ or $\displaystyle\Vert \nabla_{\mathbb{B}}u_{0}\Vert_{L_{2}^{\frac{n}{2}}(\mathbb{B})} = 0$ and blows up in finite time with $I(u_{0}) < 0$; for the critical initial energy $J(u_{0}) = d$, the solution is global in time with $I(u_{0}) \geq0$ and blows up in finite time with $I(u_{0}) < 0$. The decay estimate of the energy functional for the global solution and the estimates of the lifespan of local solution are also given.

Vibration problems have become one of the most important factors affecting robot performance. To this end, a terminal residual vibration suppression method based on joint trajectory optimization is proposed to improve the accuracy and stability of robot motion. Firstly, based on the characteristics of the friction nonlinearity due to joint coupling and physical feasibility of dynamic parameters, a semidefinite programming method is used to identify dynamic parameters with actual physical meaning, thereby obtaining an accurate dynamic model. Then, based on the result of the residual vibration time domain analysis, a joint trajectory optimization model with the goal of minimizing joint tracking error is established. The Chebyshev collocation method is used to discretize the optimization model. The dynamic model is used as the optimization constraint, and barycentric interpolation is used to obtain the optimized joint motion trajectory. Finally, industrial robot experiments prove that the vibration suppression method proposed in this article can reduce the maximum acceleration amplitude of residual vibration by 62% and the vibration duration by 71%. Compared with the input shaping method, the method proposed in this paper can reduce the terminal residual vibration more effectively and ensure the consistency of running time and trajectory.

Promoting the sustainable development of resource-based cities is of great significance to the ecological protection and high-quality development of the Yellow River Basin. Combining the environmental status and economic development, we objectively evaluate the ecological safety level of resource-based cities in the Yellow River Basin, compare and analysis the main factors affecting the ecological safety of different resource-based cities, and formulate precise and differentiated ecological safety protection measures in river basins to achieve high-quality development. Taking the Yellow River Basin as an example, this paper analyses the ecological level of the Yellow River Basin based on the theory of sustainable development, calculates the ecological safety level of 30 resource-based cities in the Yellow River Basin from 2006 to 2020 by TOPSIS model, and makes convergence analysis by classification. Through the DID empirical test of sustainable development planning policy on ecological safety factors, distinguish the development characteristics of different resource-based cities. The results show that: (1) the ecological safety level of resource-based cities in the Yellow River Basin is generally developing well, and there are differences among different types of resource-based cities; (2) the kinetic energy of sustainable development of resource-based cities in the Yellow River Basin is mainly industrial transformation, and the power of science and technology is insufficient; (3) local governments pay limited attention to environmental protection, and the sustainable development planning of resource-based cities in 2013 mainly promotes the adjustment of industrial structure of resource-based cities.

This paper seeks to model the crack propagation in of AAs (aluminum-alloys) 2524-T3 and 7050-T7452 subjected to fatigue loading at low temperature. Fatigue crack growth tests were performed on AAs 2524-T3 and 7050-T7452 subjected to constant-amplitude and actual random-spectra loading histories at room temperature of about 25 °C and at cryogenic temperature of -70 °C, respectively, to determine their crack growth properties and residual lives. The interaction mechanisms between cryogenic temperature and the fatigue load were deduced on the basis of the results of fractographic analysis. Temperature-dependent residual lives under actual random-spectrum load history were modeled based on a modified accumulation damage rule by accounting for the load interaction. Good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed method.

Due to the significant price difference, expensive oils like olive oil are often blended with cheaper edible oils. This practice of adulteration in edible oils, aimed at increasing profits for producers, poses a major concern for consumers. Furthermore, adulteration in edible oils can lead to various health issues impacting consumer well-being. In order to meet the requirements of fast, non-destructive, universal, accurate and reliable quality testing for edible oil, the oblique-incidence reflectivity difference (OIRD) method combined with machine learning algorithms was introduced to detect a variety of edible oils. The prediction accuracy of Gradient Boosting, K-Nearest Neighbor, and Random Forest models exceeded 95%. Experimental results indicate that the OIRD method can serve as a powerful tool for detecting edible oils.

Building outlines extracted from remote sensing images and raster maps often have irregular boundaries, redundant points, inaccurate positions, and unclear turns due to factors such as image quality, complexity of the surrounding environment, and extraction methods. This study proposes a regularization algorithm for right-angled polygon building outlines with jagged edges. First, the minimum bounding rectangle of the building outline is established and populated with a square grid based on the smallest visible length principle. An overlay analysis is then applied to the grid and original building to extract the turning points of the outline. Finally, the building orientation is used as a reference axis to sort the turning points and reconstruct the simplified building outline. Analysis of the experimental results shows that the proposed simplification method enhances the morphological characteristics of building outlines, such as parallelism and orthogonality, while considering simplification principles, such as the preservation of direction, position, area, and shape of the building. The proposed algorithm provides a new regularization method for building outlines with jagged edges.

In this paper, we study the global existence and exponential decay for a dynamic contact problem between a Timoshenko beam with second sound and two rigid obstacles, of which the heat flux is given by Cattaneo's law instead of the usual Fourier's law. The main difficulties arise from the irregular boundary terms, from the low regularity of the weak solution and from the weaker dissipative effects of heat conduction induced by Cattaneo's law. By considering related penalized problems, proving some a priori estimates and passing to the limit, we prove the global existence of the solutions. By considering the approximate framework, constructing some new functionals and applying the perturbed energy method, we obtain the exponential decay result for the approximate solution, and then prove the exponential decay rate to the original problem by utilizing the weak lower semicontinuity arguments.

For better solving both fuzziness and reliability occurring in practical issues simultaneously, Z-number deserves further exploration under uncertainty environment. Based on the credibility distribution and conversion rules, we define its expected value, variance, and semi-variance, and realize the feasibility of calculation by deriving calculation formulas. Moreover, we delve into three characteristics inherent in symmetrical Z-numbers. The link that followed between the variance and the semi-variance of Z-numbers is discovered and proved. Furthermore, we apply the formulas of expected value and variance on Z-numbers to examples, whose consequences validate our proposed formulas. The findings indicate the significance of our study in applying the expected value and variance of fuzzy sets across diverse fields.

Coarse-grained molecular dynamics simulations are employed to investigate the spatiotemporal evolution of vesicles (polymersomes) by the self-assembly of randomly distributed amphiphilic BAB triblock copolymers with hydrophilic A and hydrophobic B blocks in an aqueous solution. The vesiculation pathway consists of several intermediate structures, such as an interconnected network of copolymer aggregates, a cage of cylindrical micelles and a lamellar cage. The cage-to-vesicle transition occurs at a constant aggregation number and practically eliminates the hydrophobic interfacial area between the B block and solvent. Molecular reorganization under-lying the sequence of morphology transitions from a cage-like aggregate to a vesicle is nearly isentropic. The end-to-end distances of isolated copolymer chains in solution and those within a vesicular assembly follow log normal probability distributions. This is attributed to the pre-ponderance of folded chain configurations in which the two hydrophobic end groups of a given chain stay close to each other. However, the probability distribution of end-to-end distances is broader for chains within the vesicle as compared to that of a single chain. This is due to the swelling of the folded configurations within the hydrophobic bilayer. Increasing the hydropho-bicity of the B block reduces the vesiculation time without qualitatively altering the self-assembly pathway.

The intestinal microbiota, comprised of bacteria, archaea, and phages, inhabits the gastrointestinal tract of the organism. Male reproductive sterility is currently a prominent topic in medical research. Increasing research suggests that gut microbiota dysbiosis can result in various reproductive health problems. This article specifically investigates the impact of gut microbiota dysbiosis on male reproductive infertility development. Gut microbiota imbalances can disrupt the immune system and immune cell metabolism, affecting testicular growth and sperm production. This dysfunction can compromise the levels of hormones produced and secreted by the endocrine glands, affecting male reproductive health. Furthermore, imbalance of the gut microbiota can disrupt the gut-brain-reproductive axis, resulting in male reproductive infertility. This article will explore how the imbalance of the gut microbiota impacts male reproductive infertility through immune regulation, endocrine regulation, and interactions of the gut-brain-reproductive axis, concluding with recommendations for prevention and treatment.

This study investigates the impact of specimen size on the mechanical properties of wood, specifically focusing on compression strength, elastic modulus, and Poisson's ratio. Compression tests were conducted using three different specimen sizes (20mm×20mm×30mm, 40mm×40mm×60mm, 60mm×90mm×90mm) in the longitudinal, radial, and tangential directions. Mechanical parameters, failure mechanisms, load-displacement curves, and stress-strain relationships were systematically analyzed for each size. The study also evaluated the influence of specimen size on the accuracy of finite element numerical simulations by utilizing the obtained mechanical parameters. The results reveal a significant correlation between compressive strength and specimen size, indicating a decrease in compressive strength with increasing specimen size. Conversely, elastic modulus and Poisson's ratio exhibit less sensitivity to variations in specimen size. Notably, parameters derived from small-sized specimens (20mm×20mm×30mm) exhibited substantial errors, while those obtained from medium-sized (40mm×40mm×60mm) and large-sized specimens (60mm×90mm×90mm) demonstrated greater reliability, providing precise results in finite element numerical simulations.

High-performance electromagnetic interference (EMI) shielding materials with ultralow density and environment friendly properties are greatly demanded to address electromagnetic radiation pollution. Herein, carbon nanotubes/polylactic acid (CNTs/PLA) materials with different CNTs contents, which exhibit characteristics of light weight, environmental protection and good chemical stability, are fabricated by 3D printing technology, where CNTs are evenly distributed and bind well with PLA. The performances of 3D printed CNTs/PLA composite are improved compared to pure 3D printed PLA composite, which include mechanical properties, conductive behaviors and electromagnetic interference (EMI) shielding. The EMI shielding effectiveness (SE) of CNTs/PLA composite could be improved when the contents of CNTs increase. When it reaches 15 wt%, the EMI SE of 3D printed CNTs/PLA composite could get up to 47.1 dB, which shields 99.998% of electromagnetic energy. Meanwhile, the EMI shielding mechanism of 3D printed CNTs/PLA composite is mainly of absorption loss, and it generally accounted for more than 80% of the total shielding loss. These excellent comprehensive performances endow the 3D printed CNTs/PLA composite with great potential for use in industrial and aerospace area.

This paper mainly explores the feasibility of using desert sand (DS) and recycled aggregate in cement stabilized base. Recycled coarse aggregate (RCA) and DS serve as the substitutes of natural coarse and fine aggregates, respectively, in cement stabilized base. A four-factor and four-level orthogonal test is designed to analyze the unconfined compressive strength, splitting tensile strength, and compressive resilient modulus. Furthermore, this paper investigates the effects of cement content, fly ash (FA) replacement rate, RCA replacement rate, and DS replacement rate on the road performance of cement stabilized base composing of RCA and DS. The test results reveal that the performance of cement stabilized base with partial RCA instead of natural coarse aggregate (NCA) and partial DS instead of natural fine aggregate satisfy the road use. Meanwhile, DS is beneficial to improve the strength of cement stabilized base. The correlation and microscopic analyses of the test results imply the feasibility of applying DS and recycled aggregate to cement stabilized base. It is hoped that this paper can offer a solid theoretical foundation for promoting the application of DS and recycled aggregate in road engineering.

Domain generalization has led to remarkable achievements in Hyperspectral Image (HSI) classification. Inspired by contrastive language-image pre-training (CLIP), the language-aware domain generalization method has been explored to learn cross-domain-invariant representation. However, existing methods face some challenges: 1) The weak capacity to extract long-range contextual information and inter-class correlation. 2) Due to the inadequacies of the large-scale pre-training for HSI data, the spatial-spectral features of HSI and linguistic features can not be straightforwardly alignment. To address the above problems, a novel network has been proposed with a CLIP framework, which consists of an image encoder, based on an encoder-only transformer to obtain the global contextual information and inter-class correlation, a frozen text encoder, and a cross-attention mechanism, named Linguistic-Interact-with-Visual Engager (LIVE), enhances the interaction between two modalities. Extensive experiments demonstrating superior performance over state-of-the-art methods in HSI Domain Generalization with a CLIP framework.

Histone demethylases, enzymes responsible for removing methyl groups from histone proteins, have emerged as critical players in regulating gene expression and chromatin dynamics, thereby influencing various cellular processes. LSD2 and LSD1 have attracted considerable interest among these demethylases because of their associations with cancer. However, while LSD1 has received significant attention, LSD2 has not been recognized to the same extent. In this study, we conduct a comprehensive comparison between LSD2 and LSD1, with a focus on exploring LSD2's implications. While both share structural similarities, LSD2 possesses unique features. Functionally, LSD2 shows diverse roles, particularly in cancer, with tissue-dependent roles. Additionally, LSD2 extends beyond histone demethylation, impacting DNA methylation and DNA damage repair pathways. This study underscores the distinct roles of LSD2, providing insights into their contributions to cancer and other cellular processes.

Contaminants of Emerging Concern (CECs), a new category of contaminants in limelight, is a major issue of global concern. The pervasive nature of CECs and its harmful effects, such as cancer, reproductive disorders, neurotoxicity etc., make the situation alarming. The perilous nature of CECs lies in the fact that even very small concentration of CECs can cause great impacts on living beings. It also has a nature of bioaccumulation. Thus, it is the ultimate need to have efficient sensors for detection of CECs to ensure safe living environment. Electrochemical sensors are an efficient platform for CEC detection as they are highly selective, sensitive, stable, reproducible, and prompt, and can detect very low concentrations of analyte. Major classes of CECs are pharmaceuticals, illicit drugs, personal care products, endocrine disruptors, newly registered pesticides, and disinfection by-products. This review focusses on CECs, including their sources and pathways, health effects caused by them, and electrochemical sensors as reported in literatures under each category for the detection of major CECs.

GaN ultraviolet photodetector with metal-semiconductor-metal structure is achieved by growing on a periodic trapezoid column-shape patterned sapphire substrate using metalorganic chemical vapor deposition. Under 5-V reverse bias, the photodetector fabricated on such patterned sapphire substrate exhibits a lower dark current, a higher photocurrent, and a 476 % enhancement in the maximum responsivity as compare with those of the photodetector fabricated on conventional flat sapphire substrate. It is also found that the much larger UV-to-visible rejection ratio and the fact that responsivity drops in a smaller cut-off region are observed from photodetector fabricated by using a periodic trapezoid column-shape patterned sapphire substrate. These phenomena may all be attributed to the reduction of threading dislocation density and the improved quality of GaN film, as well as the internal reflection and/or scattering effect on the interface between GaN film and the periodic trapezoid column-shape pattern of the substrate.

Background: Pleurotus ostreutus is one of the world’s most commonly consumed mushrooms. Cultivation of mushrooms using wood resources usually results in environmental issues of deforestation. Juncao grass Pennisetum sp, Arundo Donax, and Methodology: Miscanthus are the culture mediums used in this research which offered a composting system most particularly for a simple formulation, cheap and feasible for small farms in cultivating oyster mushrooms. Results: The present study assessed the different junco grass as a substrate for growing Pleurotus ostreatus given the enzyme activities, growth, and yields. In addition, on the other hand, Lignin peroxidase (LiP) was the most active enzyme in each culture material among the other enzyme activities expressed differently between substrate and growing stages. Fruiting bodies harvested on giant grass,Arundo donax,and miscanthus,substrate weighed 159.2g/bag,132g/bag, and 65.1g/bag on average respectively. The biological efficiency of pleurotus cultivated in three different substrates was 75.2%, 63.4%, and 28.7%, respectively. Lignin peroxidase (LiP) was the most active enzyme followed by Laccase in each substrate. At the same time, other enzyme activities were differently expressed between substrate and different developmental stages. Nutrient analysis revealed significant variations, with differences in polysaccharides, proteins, and amino acids among substrates as well as the presence of heavy metals as arsenic, lead, mercury, and cadmium content in all samples was within safe limits. Conclusion: Findings from this study will serve as a solid foundation for future studies aimed at characterizing different substrate responses on enzyme activity. This research provides a sustainable footprint for subsequent research promoting eco-friendly mushroom production. The obtained results indicate that Arundo donax should be a good substrate in place of giant grass, using miscanthus is not productive based on the results obtained in this research the juncao grasses offer a sustainable approach that reduces reliance on wood-based substrates and enhances environmental sustainability.

Survival of Medulloblastoma (MB) depends on various factors, including the gene expression profiles of MB tumor tissues. In this study, we identified 967 MB survival related genes (SRBs) using the gene expression dataset of Cavalli et al. (2017) and the Cox proportional hazards regression model. Notably, the SRGs were over-represented on chromosomes 6 and 17, known for the abnormalities monosomy 6 and isochromosome 17 in MB. The most significant SRG was HMGA1 (high mobility group AT-hook 1), which is a known oncogene and a histone H1 competitor. High expression of HMGA1 was associated with worse survival, primarily in the Group 3γ subtype. The high expression of HMGA1 was unrelated to any known somatic copy number alteration. Most SRGs on chromosome 17p were associated with low expression in Group 4β, the MB subtype with 93% deletion of 17p and 98% copy gain of 17q. Pathway analysis showed that both chromosomes 6 and 17 included SRGs related to telomere maintenance and provide a rationale for testing telomerase inhibitors in Group 3 MBs. We conclude that HMGA1, along with other SRGs on chromosome 6 and 17 warrant further investigation as potential therapeutic targets in selected subgroups or subtypes of MB.

To ensure consumers can purchase high-quality rice, accurate identification of rice varieties is particularly important. Methods: This article conducts research based on machine learning algorithms from the perspectives of image, spectrum, and spectrogram fusion. Six types of hyperspectral image data of rice were preprocessed using convolutional smoothing (SG) and multiple scatter correction (MSC). Texture information of the images was extracted using gray-level co-occurrence matrix. Spectra, texture, and spectrogram data were fused into a new matrix. Spectral, texture, and spectrogram fusion data were used as inputs for the model, and support vector machines (SVM), logistic regression (LR), and K-nearest neighbors (KNN) classification models were constructed and compared. Results: From the classification results, the spectrogram fusion classification performance was better than classification models using only spectra or texture. Conclusion: The research results showed that the accuracy of SVM and LR classification models exceeded 90%, and the LR model performed the best, effectively classifying rice varieties.

Amid the swift progression of the global automobile industry, the aspiration for lightweight vehicle design has surfaced as a crucial approach to boost fuel efficiency and curtail environmental impact. The objective of this study revolves around achieving holistic optimization of vehicle structure via detailed scrutiny of vehicle process characteristics, amalgamated with a Back Propagation neural network (BPNN) optimized by a genetic algorithm (GA) and a topology optimization (TO) method.The process initiates with an examination of the vehicle's technical characteristics, succeeded by an optimization protocol that couples GA with BPNN. This exhaustive optimization procedure derives the best-fit values of design parameters and identifies the globally optimal lightweight design approach. Subsequently, a comprehensive structural optimization is actualized by modifying the topological distribution of the structure.A simulation experiment of the conceptual car body beam skeleton is conducted as a conclusive step, and the anti-collision capacity of the car body beam skeleton is assessed by measuring deformation intrusion. The findings reveal that in the vehicle topology optimization, a comparative analysis of pre and post-optimization results indicates an improved topological density across diverse sections. The topological density of the vehicle's frontal structure escalates from 0.75 to 0.8. Following optimization, the stiffness assessment records a marginal increase (within the range of 0.02–0.05), implying that the lightweight design does not compromise the general rigidity of the structure.The optimized body structure manifests superior crashworthiness in the crash test: the deformation intrusion diminishes by 27% in front-end collisions. In side impacts, the deformation and intrusion at critical points are reduced by 13.15% to 10% respectively. The comprehensive method proposed herein proves to be an efficient strategy to actualize the lightweight design of vehicles.

The long-term use of fertilizers and pesticides in conventional cultivation has resulted in a decrease in soil productivity and vegetable yields in greenhouses. However, only a limited number of studies have explored the impacts of organic cultivation on greenhouse soil. Specifically, there is a scarcity of research examining the alterations in soil aggregate mediated organic carbon and microbial communities, which are known to enhance soil productivity. This study investigated the properties of soil aggregates, including the levels of organic carbon fractions, microbial community, and enzyme activity with the three aggregate classes microaggregates (&lt;0.25 mm), small macroaggregates (2-0.25 mm) and large macroaggregates (&gt;2 mm). These investigations were conducted under three different cultivation methods in a greenhouse: conventional cultivation (CC), integrated cultivation (IC), and organic cultivation (OC) in greenhouse. The results showed that (1) OC and IC promoted the formation of small macro-aggregates and enhanced aggregate stability compared to CC, (2) SOC in the three size fractions of OC increased by 98.99%-92.06% compared to CC; EOC increased by 98.47%-117.59%; POC increased by 138.59%-208.70%; MBC increased by 104.71%-230.61%; DOC increased by 21.93%-40.90%, respectively; (3) Organic cultivation significantly increased enzyme activity in all three particle size aggregates and increased the relative abundance of bacteria in micro-aggregates as well as the relative abundance of fungi in small macro-aggregates. Structural equation model (SEM) analysis revealed that organic farming practices fostered the development of smaller macro-aggregates, elevated microbial and enzyme activities within soil aggregates, and facilitated the conversion of soil nutrients and carbon sequestration. consequently, this led to an increase in soil organic carbon content and improved vegetable yield in greenhouse environments. In conclusion, the soil carbon content and vegetable yield are enhanced through long-term organic cultivation in greenhouses, primarily by increasing the proportion of small macro-aggregates.

Let G[F,Vk, Huv] be the graph with k pockets, where F is a simple graph of order n ≥ 1,Vk= {v1,v2,··· ,vk} is a subset of the vertex set of F and Hvis a simple graph of order m ≥ 2,v is a specified vertex of Hv. Also let G[F,Ek, Huv] be the graph with k edge pockets, where F is a simple graph of order n ≥ 2, Ek= {e1,e2,···ek} is a subset of the edge set of F and Huvis a simple graph of order m ≥ 3, uv is a specified edge of Huvsuch that Huv− u is isomorphic to Huv− v. In this paper, we derive closed-form formulas for resistance distance and Kirchhoff index of G[F,Vk, Hv] and G[F,Ek, Huv] in terms of the resistance distance and Kirchhoff index F, Hv and F, Huv, respectively.

Earth observation satellites can capture images of specific areas in Earth's orbit based on user requirements. Despite the high demand for satellite imagery, satellites remain a scarce resource. When there are many observation tasks that are large and dense, they may interfere with each other due to satellite mobility. To address this issue, a multi-satellite scheduling algorithm based on a task merging mechanism has been proposed. This paper proposes a two-stage approach to the problem: task merging phase and merging task scheduling phase. The task merging phase introduces two methods based on Mean Shift and Complete Graph to generate the merging task set. In the merging task scheduling phase, a multi-satellite scheduling algorithm based on merging tasks is employed to solve the problem. Finally, certain measurement experiments suggest the effectiveness of the algorithm.

Since the 21st century, China's urbanization process has been rapid development, the concept and function of urban public space in the city has been gradually paid attention to. In order to guarantee life and water, most urban construction relies on rivers, and Bridges are the most important way to communicate between urban areas. The main functional part of the bridge is the span structure, that is, the bearing structure of the bridge, and the lower part of the "gray" space formed by the bridge structure. Considering the social level, with the economic growth and urbanization development, people have brought a better living environment and quality of life, and also improved the requirements for urban public environment. In the increasingly tense urban space, how to use and transform the space under the bridge is a problem that needs to be considered and solved. In view of this problem, in this study, we try to solve the micro-transformation of space under Bridges in cities through public art from the perspective of "regional culture" and "art for all". This paper analyzes the micro-transformation of space art under Bridges in two large cities of Shanghai and Foshan, namely, the space under Bridges under Songhong Road in Shanghai, the space under Bridges under Central Of Suzhou River and the space under Bridges under Pingsheng Bridge in Foshan. This paper discusses the cultural intervention of "regional culture" in the micro-transformation of the space under the bridge, and the influence and effect of "art for all" on the public art space under the bridge after the transformation to the community and the public.