A composite flocculant P(AM–DMDAAC) was synthesized by the copolymerization of acrylamide (AM) and dimethyl diallyl ammonium chloride (DMDAAC). Using microwave (MV) assistance with ammonium persulfate as initiator, the synthesis provided short reaction time and better solubility product. Nuclear magnetic resonance spectroscopy (1H NMR and 13C NMR), Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and differential thermal analysis-thermo gravimetric analyzer (DTA-TGA) were used to determine the structure and morphology of P(AM–DMDAAC). Parameters affecting the intrinsic viscosity ([η]) of P(AM–DMDAAC), such as microwave time, mass ratio of DMDAAC to AM, initiator ammonium persulfatedosage, sodium benzoate dosage, bath time, reaction temperature and pH value were examined. Results showed that the optimum synthesis conditions were microwave time 1.5 min, m(DMDAAC): m(AM) is 4:16, 0.5 wt‰ initiator, 0.4 wt‰ EDTA, 0.3 wt‰ sodium benzoate, 2 wt‰ urea, 4 h bath time, 4.0h reaction time and pH 2. To study the removal of phenol by P(AM–DMDAAC), the influence of flocculant dose, pH value and the stirring speed were investigated, with optimization providing 99.8 % removal.

Water resource is considered as a significant factor in development of regional environment and society. Water consumption prediction can provide important decision basis for the regional water supply scheduling optimisations. According to the periodicity and randomness nature of the daily water consumption data, a Markov modified autoregressive moving average (ARIMA) model is proposed in this study. The proposed model, combined with the Markov chain, can correct the prediction error, reduce the continuous superposition of prediction error, and improve the prediction accuracy of future daily water consumption data. The daily water consumption data of different monitoring points are used to verify the effectiveness of the model, and the future water consumption is predicted, in the study area. The results show that the proposed algorithm can effectively reduce the prediction error compared to the ARIMA.

Yaw misalignment can make a wake steer, which is an effective method to increase the power of wind farms, but it also increases the fatigue load of the turbines. In this paper, the method of combining yaw misalignment and pitch control (CYMP) is proposed to investigate the potential to mitigate wake interference, the wind velocity distribution and turbulence distribution in the wake, as well as the power and load changes of the wind turbine are studied, focusing on power in-crement and fatigue damage reduction. Although some studies have found that the method of CYMP are beneficial to increase power generation and reduce fatigue loads, there are no papers that have made a detailed analysis of the effects of wake turbulence, wind speed distribution, power, especially fatigue damage under this control. Simulation tool FAST.Farm is used to model and analyze wind farms, obtain the variation details of wake and provide simulation data for calculating power and fatigue load. The pitch control brings bias to the CYMP optimization results was neglected, the case studies show that the method of CYMP can reduce the fatigue load by 10.29% and increase the total power by 1.7% compared with only wake steering. The Model Predictive Control collaborative method based on CYMP is proposed, which can increase power by more than 2% and reduce thrust by more than 4% under 10m/s turbulent wind.

Over the past four decades, China has experienced a nutritional transition and has developed the largest population of internet users. In this study, we evaluated the impacts of internet access on the nutritional intake in Chinese rural residents. An IV-Probit-based propensity score matching method was used to determine the impact of internet access on nutritional intake. The data were collected from 10042 rural households in six Chinese provinces. The results reveal that rural residents with internet access have significantly higher energy, protein, and fat intake than those without. Chinese rural residents with internet access consumed 1.35% (28.62 kcal), 5.02% (2.61 g), and 4.33% (3.30 g) more energy, protein, and fat, respectively. There was heterogeneity as regards the intake of energy, protein, and fat among those in different income groups. Moreover, non-staple food consumption is the main channel through which internet access affects nutritional intake. The results demonstrate that the local population should use the internet to improve their nutritional status. Further studies are required to investigate the impact of internet use on food consumed away from home and micronutrients intake.

This paper proposes a solution for the problem of mobile robot navigation and trajectory interpolation in dynamic environments with large scenes. The solution combines a semantic laser SLAM system that utilizes deep learning and a trajectory interpolation algorithm. The paper first introduces some open-source laser SLAM algorithms and then elaborates in detail on the general framework of the SLAM system used in this paper. Secondly, the concept of voxel is introduced into the occupation probability map to enhance the ability of local voxel maps to represent dynamic objects. Then, in this paper, we propose a PointNet++ point cloud semantic segmentation network combined with deep learning algorithms to extract deep features of dynamic point clouds in large scenes and output semantic information of points on static objects. A descriptor of the global environment is generated based on its semantic information. Closed-loop completion of global map optimization is performed to reduce cumulative error. Finally, T-trajectory interpolation is utilized to ensure the motion performance of the robot and improve the smooth stability of the robot trajectory. The experimental results indicate that the combination of the semantic laser SLAM system with deep learning and the trajectory interpolation algorithm proposed in this paper yields better graph building and loop closure effects in large scenes at SIASUN large scene campus. The use of T-trajectory interpolation ensures vibration-free and stable transitions between target points.

The pathogen Cryptococcus neoformans is a major cause of fungal meningitis in humans. As with other melanotic microorganisms associated with human diseases, the cell wall-associated melanin of C. neoformans is a major virulence factor that contributes to its ability to evade host immune responses. The levels of melanin substrate and the regulation of melanin formation could be influenced by the microbiota-gut-brain axis. Moreover, recent studies show that C. neoformans infection causes dysbiosis in the human gut microbiome. In this review, we discuss the potential association between cryptococcal meningitis and the gut microbiome. Additionally, we emphasize the promising prospects of targeting the gut microbiome as a means of diagnosing and treating this debilitating disease.

High-entropy alloys have attracted widespread attention from researchers worldwide due to their unique microstructure and outstanding mechanical properties, making them a prominent focus in the field of metallurgy. Among the various high-entropy alloys, the CoCrCuNi system was among the first alloys discovered, and it has shown significant progress in development. By employing different preparation and heat treatment processes, researchers have obtained alloys with diverse performances. The addition of various alloying elements or other components can lead to pronounced variations in the properties of CoCrCuNi high-entropy alloys. This work provides a comprehensive review of recent research progress on CoCrCuNi high-entropy alloys both domestically and internationally. It covers the preparation methods, thermodynamic and kinetic simulation calculations, as well as discussions on heat treatment processes and the influence of alloying elements on the microstructure and mechanical properties of CoCrCuNi high-entropy alloys. Finally, the review concludes with a prospective analysis and predictions for the potential applications and future directions in developing novel high-entropy alloys.

Motivation: UCSC Xena platform provides huge amounts of processed cancer omics data from big public projects like TCGA or individual reserach groups for enabling unprecedented research opportunities. In 2019, we developed UCSCXenaTools, an R package for retrieval of UCSC Xena data. However, an easier dataset exploration and analysis tool is still lack, especially for researchers without programming experience. Results: We develop UCSCXenaShiny, an R Shiny package to quickly explore, download all datasets from UCSC Xena data hubs. In addiction, a module based analysis framework is constructed to analyze and visualize data. Availability: https://github.com/openbiox/UCSCXenaShiny or https://cran.r-project.org/package=UCSCXenaShiny.

In recent years, ozone (O3) pollution has been rapidly spreading, restricting further improvement of air quality in China. Investigating the interaction of O3 concentration and identifying their driven cities are important for the prevention and control of O3 pollution in China. However, the complex interaction between O3 pollution between the cities and their driven cities has not yet been revealed. In this study, we address this gap based on complex network methods. Specifically, an ozone relational network is constructed using an association calculation method. The driven nodes and spatial clusters were analyzed based on the maximum matching algorithm and the Louvain algorithm. The findings of the study reveal an aggregation phenomenon in the ozone network concerning distance. Furthermore, as the threshold Tc varies, the proportion of driven nodes exhibits a positive correlation. Moreover, a closer threshold value corresponds to a higher coincidence ratio of the driven nodes. The results provide scientific guidance for national O3 pollution prevention and regional synergy formatting. Furthermore, the introduced network-based approaches offer a mythological framework for the study of air pollution in key cities and clusters.

During public health events, Active Mobility (walking and cycling) plays an important role in securing residents' travel. To enhance the resilience of urban transportation, this article integrates the travel environment elements for walking and cycling and constructs a travel environment for Active Mobility evaluation index system. This article uses survey data from the main urban area of Harbin in the context of the COVID-19 pandemic in May 2022, and combines the Gradient Boosting Decision Tree (GBDT) and Impact-Asymmetry Analysis (IAA) methods to analyze the satisfaction of the travel environment for Active Mobility. It proposes strategies for optimizing the travel environment for Active Mobility, ensuring residents' travel during public health events, guiding them to adopt Active Mobility, and improving urban transportation resilience. This research shows that Active Mobility can enhance urban transportation resilience. In addition, there are differences in resident demand for walking and cycling environments in the travel environment for Active Mobility. Residents are more concerned about the comfort of the walking environment, while they prioritize the convenience of the cycling environment.

The use of salt rock for underground radioactive waste disposal facilities requires a comprehensive analysis of creep-damage process in salt rock. A computer-controlled creep setup is employed to carry out a creep test of salt rock lasted as long as 359 days under a constant uniaxial stress. The AE space-time evolution and energy releasing characteristics during creep test are studied in the meantime. A new creep-damage model is proposed on the basis of fractional derivative by combining the AE statistical regularity. It indicates that the AE data in non-decay creep process of salt rock can be divided into three stages. Furthermore, the parameters of new creep-damage model are determined by Quasi-Newton method. The fitting analysis suggests that the creep-damage model based on fractional derivative in this paper provides a precise description of full creep regions in salt rock.

The human serotonin transporter (hSERT) terminates neurotransmission by removing serotonin from the synaptic cleft, which is an essential process plays an important role in depression. In addition to substrate serotonin, hSERT is also the target of drugs of abuse like cocaine and clinically used antidepressants such as escitalopram and paroxetine. To date, few studies attempt to investigate the unbinding mechanism underlying the orthosteric and allosteric modulation of hSERT. The high-resolution X-ray structure of hSERT resolved recently enables us to theoretically study the unbinding of the above four ligands against the S1 or S2 site of hSERT, by means of molecular docking, molecular dynamics (MD) and potential of mean force (PMF) simulations. We proved that for either the S1 or S2 site, the other three ligands (cocaine, escitalopram and paroxetine) are much more favorable than the original substrate serotonin, whether in kinetics along the unbinding pathways or in thermodynamics at the equilibrium states. Furthermore, the S1 site is much more favorable than the S2 site, for each ligand. Interestingly, inspection revealed that there are ~ 3Å lengths between the allosteric site of serotonin and cocaine, and an unseen un-binding pathway for escitalopram at the S1 site except for verification of the broadest trail.

Beef potentiator is an important flavor enhancer in food industry, while it is prone to generating insufficient taste compounds and off-odor compounds during enzymatic hydrolysis of beef, resulting in poor flavor of beef potentiator. It has been extensively reported that sonication is capable of improving food flavor. However, the effect of sonication on the flavor of enzymatically hydrolyzed beef liquid (EHBL) was scarcely reported. Herein, we investigated the effect of sonication on the flavor of EHBL using quantitative descriptive analysis (QDA), physicochemical analysis and SPME-GC-olfactometry/MS. QDA showed that sonication had a significant effect on taste improvement and off-odor removal of EHBL. Compared with the control, sonication (40 kHz, 80 W/L) increased the contents of total nitrogen, formaldehyde nitrogen, total sugar, reducing sugar, free amino acids (FAAs) and hydrolysis degree of EHBL by 19.25%, 19.80%, 11.83%, 9.52%, 14.37% and 20.45%. Notably, sonication markedly enhanced the contents of sweet FAAs, umami FAAs and bitter FAAs of EHBL by 19.66%, 14.04% and 9.18%, respectively, which contributed to the taste improvement of EHBL. SPME-GC-olfactometry/MS analysis showed that aldehydes and alcohols were the main contributors to aroma compounds of EHBL, sonication significantly increased the contents of key aroma compounds and 115.88% of alcohols content in EHBL. Notably, sonication decreased contents of the fishy odorants, hexanoic acid and nonanal, markedly by 35.29% and 26.03%, which was responsible for the aroma improvement of EHBL. Therefore, sonication could become a new potential tool to improve the flavor of EHBL.

Limonene is a valuable monoterpenoid that with diverse applications. Microbial biosynthesis offers a sustainable alternative to plant-based extraction, which is prone to hinderance by climate change and acreage. In the present study, the effects on limonene production of carbon source, inoculum, working volume, temperature, pH, dodecane coverage, and media were investigated with engineered strains of Rhodosporidium toruloides. Through single-factor and orthogonal experiments, the limonene titer was improved from 52.2 to 358.1 mg/L on 250-mL flask, a 586% increase. The optimized medium was MM, with a working volume of 50 mL, inoculum OD600=0.6, 22 °C, pH 6, and dodecane coverage (v/v) of 20%. The results here demonstrated that the R. toruloides could be explored as an efficient limonene producer and facilitate other monoterpenoids biosynthesis with R. toruloides.

Genome-scale metabolic models (GEMs) have been widely used for phenotypic prediction of microorganisms. However, the lack of other constraints in the stoichiometric model often leads to a large metabolic solution space inaccessible. Inspired by previous studies that take allocation of macromolecule resources into account, we developed a simplified Python-based workflow for constructing enzymatic constrained metabolic network model (ECMpy) and constructed an enzyme-constrained model for Escherichia coli (eciML1515) by directly adding a total enzyme amount constraint in the latest version of GEM for E. coli (iML1515), considering the protein subunit composition in the reaction, and automated calibration of enzyme kinetic parameters. Using eciML1515, we predicted the overflow metabolism of E. coli and revealed that redox balance was the key reason for the difference between E. coli and Saccharomyces cerevisiae in overflow metabolism. The growth rate predictions on 24 single-carbon sources were improved significantly when compared with other enzyme-constrained models of E. coli. Finally, we revealed the tradeoff between enzyme usage efficiency and biomass yield by exploring the metabolic behaviors under different substrate consumption rates. Enzyme-constrained models can improve simulation accuracy and thus can predict cellular phenotypes under various genetic perturbations more precisely, providing reliable guidance for metabolic engineering.

Stormwater management is a key urban issue in the world, in line with the global issues of urban sprawl and climate change. It is urgent to investigate the effectiveness in managing stormwater with different strategies for maintain urban resilience. A method based on a storm water management model (SWMM) was developed for assessing the control of stormwater runoff volume and the percentage removal of suspended solids by implementing a Sponge City strategy. An interdisciplinary approach was adopted incorporating Low Impact Development (LID) with urban Green Infrastructure and Gray Infrastructure paradigms in a typical old residential community in Suzhou, China. Four types of sponge facilities for reducing stormwater runoff were bio-retention cells, permeable pavements, grassed pitches, and stormwater gardens. The simulation results indicate that the stormwater pipe system can meet the management standard for storms with a five-year recurrence interval. The volume capture ratio of annual runoff is 91% and the reduction rate of suspended solids is 56%. This study demonstrates that Sponge City strategy is an effective approach for managing stormwater, particularly in old and densely populated urban areas. Implementing spongy facilities with a LID strategy for stormwater management can significantly enhance urban water resilience and increase ecosystem services.

With the gradual improvement of coal mining efficiency, the disturbance of groundwater system caused by the high-intensity mining mode also increases, which is a more severe challenge to the prevention of mine safety and the protection of water resources in mining areas. How to accurately describe the dynamic changes of the groundwater system under mining and quantitatively predict mine water inflow is a major problem in the current research. Based on the full analysis of the response characteristics of groundwater system to the extraction disturbance, this paper forms a kind of method to establish a mine hydrogeological conceptual model that can accurately represent the water inrush process, and uses the MODFLOW non-structural division grid to accurately characterize the formation structure, and finally make accurate water inflow prediction. Taking the Caojiatan Coal Mine in Shaanxi Province, China as an example, a numerical model of unstructured mine water inrush was established for the first time, and the changes of water inflow source and water inflow intensity were quantitatively evaluated. Compared with the traditional water inflow prediction method, it is found that the prediction accuracy is improved by 12%~17% by detailing the response characteristics of complex groundwater system under high-strength coal seam mining conditions. The method is of great significance and promotion value for the comprehensive understanding of the disturbance characteristics of human underground engineering activities, such as coal mining, on the groundwater system, and for accurately predicting water inflow.

Using the data of China's A-share non-financial listed enterprises from 2015 to 2022 as a sample, this study empirically tests the impact of ESG rating disagreement on corporate debt financing cost. The results show that ESG rating disagreement significantly increases the debt financing costs of enterprises, and this result still holds after a series of robustness tests such as replacing the dependent and independent variables and PSM approach. Meanwhile, the heterogeneity analysis reveals that non-state-owned enterprises and enterprises in non-heavily polluting industries are more sensitive to ESG ratings disagreement. In addition, mechanism analysis shows that corporate financing constraints mediate the relationship between ESG rating disagreements and debt financing costs. The findings of this study provide important evidence for understanding the impact of ESG rating disagreement on the costs of debt financing, enrich the meaning of ESG rating disagreement, and reveal the significance of unifying ESG rating standards.

The transforming growth factor-β (TGF-β), in which overexpression have been associated with various diseases, has become an attractive molecular target for the treatment of cancers. Three series of 3-substituted-4-(quinoxalin-6-yl) pyrazoles 14a–h, 15a–h, 16a–h, 22a, 22b, 22d, 23a, 23b, 23d, 24b, and 24d were synthesized and evaluated for their activin receptor-like kinase 5 (ALK5) and p38α mitogen activated protein (MAP) kinase inhibitory activity in an enzymatic assays. Among these compounds, the most active compound 16f inhibited ALK5 phosphorylation with an IC₅₀ value of 0.28 µM, with 98% inhibition at 10 µM. Compound 16f also had good selectivity index of >35 against p38α MAP kinase, with 9.0-fold more selective than clinical candidate, compound 3 (LY-2157299). Molecular docking study was performed to identify the mechanism of action of the synthesized compounds and their good binding interactions were observed. ADMET prediction of good active compounds showed that these ones possess good pharmacokinetics and drug-likeness behavior.

Silicon carbide single crystal (SiC) has been widely used in the field of power devices, while it is difficult to fabricate ultra-flat surface by traditional manufacturing technologies due to its difficult-to-machine property. This paper investigates the interaction process during femtosecond laser ablation of crystalline silicon carbide based on the two-temperature model simulation and experimental study. The findings reveal that parameters such as laser pulse energy, scanning interval, and defocus amount exert significant influence on ablation depth, roughness, and surface morphology. The femtosecond laser proves effective in removing surface defects from cut SiC substrates, albeit resulting in increased surface roughness. However, subsequent polishing treatment of the laser-ablated silicon carbide surface can mitigate this roughness, underscoring the feasibility of laser surface ablation for silicon carbide single crystals.

In response to the structural optimization problem of PCB stator coreless disc motors, the orthogonal response surface method was used to optimize the motor structure, determine the basic parameters of the motor preliminarily, and conduct orthogonal experiments on the motor parameters based on the optimization design objectives, The optimization factors were the quantity of magnetic pole of the motor rotor, the ratio of main/auxiliary pole size, the thicknessof the permanent magnet, and the air gap length.The motor torque，the amplitude of magnetic density of the air gap and waveform distortion rateare used as optimization objectives. The motor parameters that make the motor torque reach the maximum, the air gap magnetic density maximum, and the waveform distortion rate minimum. Due to the use of PCB plates instead of motor stator cores in PCB coreless disc motors,The service life of the PCB board during motor operation will be reduced with the temperature rise generated by the stator winding To solve this problem, the response surface analysis of the motor is carried out to reduce the temperature rise of the stator windings during the operation of the motor. PCB board and stator winding are the main factors affecting the temperature rise of the motor.Taking the thickness of the PCB board, the hole diameter on the board, and the uneven width of the stator winding as optimization factors, the motor parameters with the lowest temperature rise of the motor winding are obtained. Simulation analysis is conducted using Ansys/Maxwell software, and the results prove the feasibility of optimization.

Establishing an accurate mathematical model is the foundation of simulating the motion of marine vehicles and structures, and it is the basis of modeling-based control design. System identification from observed input-output data is a practical and powerful method. However, for modeling objects with different characteristics and known information, a single modeling framework can hardly meet the requirements of model establishment. Moreover, there are some challenges in system identification, such as parameter drift and overfitting. In this work, three robust methods are proposed for generating ocean hydrodynamic models based on Bayesian regression. Two Bayesian techniques, semi-conjugate linear regression and noisy input Gaussian process regression, are used for parametric and nonparametric gray-box modeling and black-box modeling. The experimental free-running tests of the KVLCC2 ship model and a multi-freedom wave energy converter (WEC) are used to validate the proposed Bayesian models. The results demonstrate that the proposed schemes for system identification of the ship and WEC have good generalization ability and robustness. Finally, the developed modeling methods are evaluated considering the aspects required conditions, operating characteristics and prediction accuracy.

Four previously undescribed highly oxygenated diterpenoids (1–4), zeylleucapenoids A–D, characterized by halimane and labdane skeletons, were isolated from the aerial parts of Leucas zeylanica. Their structures were elucidated primarily by NMR experiments. The absolute configuration of 1 was established by theoretical ECD calculations and X-ray crystallographic analysis, whereas those for 2−4 were assigned by theoretical ORD calculations. Zeylleucapenoid D (4), with an IC₅₀ value of 38.45 μM in RAW264.7 macrophages and nontoxic activity for zebrafish embryo, and obviously inhibited pro-inflammatory cytokines TNF-α and IL-6 in a dose-dependent manner. Compound 4 inhibited of the expression of inducible nitric oxide synthase (iNOS) and cyclooxygenase-2 (COX-2). Furthermore, molecular docking analysis indicated the possible mechanism of action for 4 may be bind to targets by hydrogen- and hydrophobic- bond interactions.

The Yangtze River is cross-linked with numerous lakes within its floodplain and is a worldwide biodiversity hotspot. There is no evidence indicating when this unique river-lake system developed. The endemic East Asian cyprinid clade has evolved diverse spawning adaptations to different flow conditions. Our ancestral egg-type reconstruction showed an ancestral state of adhesive eggs and later demersal eggs origination (both stream adaptations). Semi-buoyant eggs emerged ~18 Mya as a fast-flowing river adaptation, with increased hydration via three yolk protein degradation pathways, ion transport pathways and egg envelope permeability transition pores. Adhesive eggs evolved secondarily ~14 Mya with the egg envelope increasing to four layers and an adhesive layer, along with an increase in adhesiveness via microfilament/adhesive-related protein crosslinking and enhanced glycosaminoglycan biosynthesis, improving adherence to submerged lake plants, indicating that the cross-linked river-lake system formed in the mid-Miocene. This study provides a unique biological evidence for large-scale water system evolution.

Mountain ecosystems are crucial for global biodiversity conservation. However, their landscape features are constantly changing owing to urban expansion. Understanding the relationships between biotic communities and landscape features is essential for biodiversity conservation. This study aimed to examine the effect of land-cover type on avian communities in Lishui, a mountainous urban area in eastern China. Avian surveys were conducted using a total of 168 line transects across different land-cover types once per season from December 2019 to January 2021. We assessed the diversity of bird communities by calculating various metrics at both taxonomic and functional levels. Among the land-cover types measured, woodland, built-up land, cultivated land, and water bodies significantly influenced bird community diversity and composition. Species richness, species abundance, and functional richness were negatively correlated with the proportion of woodland but positively correlated with the proportion of non-natural land cover, such as built-up and cultivated land. In contrast, functional evenness was positively correlated with the proportion of woodland and grassland but negatively correlated with the proportion of non-natural land cover. Land-cover type also exhibited significant correlations with avian functional characteristics such as diet, foraging strata, and body mass, thereby influencing the overall community structure. Our results indicated that mountainous landscape patterns substantially affect avian communities. Different land-cover types possess varying resource endowments that affect the distribution of avian species. Therefore, urban landscape planning in mountainous areas should carefully consider the various functions provided to organisms by different types of land cover to promote biodiversity.

Reducing the hardness of hard water is of great concern nowadays due to some adverse effects on water pipes, boilers and soap consumption. Using the method of biomineralization to precipitate calcium and magnesium ions to become carbonate minerals was one of the most important innovations for reducing the hardness of hard water. The present study sought to explore the physical and chemical conditions of carbonates bio-precipitation and the potential use of Bacillus licheniformis SRB2 strain (GenBank: KM884945.1) isolated from sludge sample of Moshui River (Shandong University of Science and Technology, Qingdao, China) in reducing the hardness of hard waters by the induction of carbonate minerals. In this study, B. licheniformis SRB2 strain was identified based on the morphological, biochemical and 16S rDNA gene sequence homology analysis. The carbonate minerals induced by B. licheniformis bacteria in the liquid culture medium with 3% NaCl and Mg/Ca molar ratio of 0, 6, 8, 10 and 12 were investigated. The culture medium was inoculated with the bacterial liquid seed was set as the experimental group and the other culture medium was inoculated with the same volume of distilled water was set as the control group. The mineral phases, micromorphologies, and crystal structures were analyzed using X-ray powder diffraction, scanning electron microscope, energy dispersive X-ray detector, high resolution transmission electron microscopy and selected area electron diffraction. The bacterial concentrations and pH values of the solution were measured by a spectrophotometer and a pH meter, respectively. The urease secreted by B. licheniformis SRB2 was found to greatly increase the pH values of the liquid medium, which favored the formation of calcium carbonate.As a result, Mg²⁺ and Ca²⁺ ion concentrations decreased greatly due to the biomineralization of calcium carbonate and nesquehonite minerals in the presence of B. licheniformis SRB2 bacterium. There were only few calcium carbonates and no nesquehonite minerals in the control groups. It was also found that the minerals of nesquehonite induced by B. licheniformis SRB2 had a phenomenon of preferred orientation. What was more, even though Mg²⁺ ions inhibited the precipitation of Ca²⁺ ions, but under the action of B. licheniformis SRB2 bacteria, the inhibition effect was significantly declined. The bio-precipitation of calcium carbonate and nesquehonite minerals may represent a new method of pretreatment for the hardness reduction of hard water. The accomplished study is of certain interest for interpretation of the carbonates biomineralization in natural environment, and maybe also has a certain application value in the former processing of hard water

In this study, 10%PTFE/PEEK blend were modified by potassium titanate whisker (PTW) and chopped glass fiber (GF), respectively. The blends were prepared by three-screw extruder. Through the investigation of thermal stability, tribological properties, mechanical properties and rheological behavior, the effects of reinforcing agents were determined. The results illustrated that the mechanical properties of 10%PTFE/PEEK blend can be dramatically improved by adding reinforcing agent of PTW or GF, and the reinforcing effect of GF was especially obvious. As for tribological properties, 1% addition was the best proportion. The friction coefficient and wear rate of the blend with 1% PTW were 0.283 and 4.97 × 10^-6 mm³/N · m, which decreased by 7.2% and 21% compared with those of the blend without reinforcing agent.

Gut microbiota dysfunction is a key factor affecting chronic kidney disease (CKD) susceptibility. Puerariae Lobatae Radix (PLR), a traditional Chinese medicine and food homologous herb, is known to promote gut microbiota homeostasis, however, its role in renoprotection remains unknown. This study aimed to investigate the efficacy and potential mechanism of PLR to alleviate CKD. An 8-week 2% NaCl-feeding murine model was applied to induce CKD and evaluate the therapeutic effect of PLR supplementary. After gavage for 8 weeks, PLR significantly alleviated CKD-associated creatinine, urine protein increasement and nephritic histopathological injury. Moreover, PLR protected kidney from fibrosis by reducing inflammatory response and down-regulating the canonical Wnt / β-catenin pathway. Further, PLR rescued gut microbiota dysbiosis and protected high salt-induced gut barrier dysfunction. We found enrichment of Akkermansia and Bifidobacterium after PLR intervention, the relative abundance of which were in positive correlation with normal maintenance of renal histology and function. Next, fecal microbiota transplantation experiment verified that the positive effect of PLR on CKD was at least partially exerted through gut microbiota reestablishment and down-regulation of the Wnt / β-catenin pathway. Our study provides evidence for new function of PLR on kidney protection and put forward a potential therapeutic strategy target for CKD.

The thesis proposes a argument that a mass point moving in a horizontal circle on the Earth’s surface can generate a radial centrifugal force of the Earth’s center of mass, thus realizing an unconventional anti-gravity path. Based on the author’s theory of absolute airspace and its reference system, and through the theoretical analysis of the difference in the distribution of gravitational acceleration at different latitudes caused by the rotation of the earth, and the centrifugal force of a mass point moving in a horizontal circle on the earth’s surface is analyzed, the validity of the argument is demonstrated. At the same time, the paper puts forward two possible basic principles, and makes theoretical analysis and demonstration. Conceive of the concrete experimental verification of principle two is proposed. Four technical schemes for anti-gravity ascent are proposed and basic analysis is made. On the premise of not fully considering the practical technical ability, it is theoretically proved that three of them have realistic operability and development potential. In theory, this paper opens up a different way of anti-gravity for human beings, which will bring new ideas and prospects for human beings to get rid of the bondage of gravity.

This paper is based on the concept of absolute airspace and its local absolute stationary reference system proposed by the author, on the premise of abandoning space concept and the relativity principle of relativity theory, It is proposed that general relativity and special relativity can be unified into Simple and practical a space-time transformation theory which fully includes other basic physical principles of relativity. And the unified and simple expression of the time transformation effect is proved and deduced. By comparing with the theoretical derivation and checking calculation of Hafele-Keating experiment in an ideal state, It is proved that the expression of time transformation effect proposed in this paper is completely correct. Compared with the theory of relativity, the calculation is simpler and more accurate. The paper also puts forward two checking prediction of physical cases about the time transformation effect, which are left for the capable competent unit or individual to verify in practice.

The paper suggests that the physical priciple of special relativity's space-time transformation effect is wrong, Uniform linear motion without acceleration does not exist objectively, nor does its same reference frames. Therefore, it is inferred that the space-time transformation effect of special relativity is caused by the acceleration of moving objects, special relativity is only a part of general relativity, not a theoretical system that exists independently from general relativity. The corresponding mathematical demonstration and calculation verification are carried out, and the result proves that the inference of the paper is correct. At the same time, it further explains that the concept of absolute airspace is correct. Special relativity has serious errors in the concept of space, the principle of relativity and the physical principle of space-time transformation effect. Therefore, it is necessary to make a series of revisions to the theory of relativity and to reinterpret some related physical problems.

In this paper, the Hafele‐Keating experiment and the geostationary orbit satellite of related physics problems of are analyzed and discussed in detail. If researchers read the paper and think about it, It will be found that the Hafele‐Keating experiment and the geostationary satellite problem prove that some of the core ideas and theories of relativity are seriously wrong. Isnʹt that a very serious problem in physics? Canʹt this cause the academic circles to pay great attention to it? Isnʹt this worthy of in‐depth analysis and research? The core of the paper is to point out that there are problems with the space concept and the reference system theory of classical physics and relativity, And that would bring up a whole host of physics problems. It takes a concerted effort from the academic community, Do furtherin‐depth analysis and research. Strive forthe further discovery and perfection of physics theory.

In this paper, under the symmetric entropy and the scale squared error loss functions, we consider the maximum likelihood (ML) estimation and Bayesian estimation of the Shannon entropy and Rényi entropy of the two-parameter inverse Weibull distribution. In the ML estimation, the dichotomy is used to solve likelihood equation. In addition, the approximation confidence interval is given by the Delta method. Because the form of estimation results is more complex in the Bayesian estimation, the Lindley approximation method is used to achieve the numerical calculation. Finally, Monte Carlo simulations and a real data set are used to illustrate the results derived. By comparing the mean square error between the estimated value and the real value, it can be found that the performance of ML estimation of Shannon entropy is better than that of Bayesian estimation, and there is no significant difference between the performance of ML estimation of Rényi entropy and that of Bayesian estimation.

Fabrication of a nanocrystal zinc oxide (ZnO)/nitrogen-doped (N-doped) graphene composite using a novel and facile in situ sol-gel technique is demonstrated. Two-dimensional nanostructure morphology with uniform ZnO nanoparticles (average diameter of 10.25 nm) anchored on N-doped graphene nanosheets was observed via electron microscopy. Because of the polar heteroatoms on the graphene sheets, an abundance sites for polysulfide absorption were provided. More importantly, the strong chemical interaction between ZnO and polysulfides efficiently hindered the transport of polysulfides. Consequently, the lithium/sulfur (Li/S) battery with the ZnO/N-doped graphene composite-coated separator delivered enhanced performance in terms of discharge capacity and cycling stability when compared to the cell with a normal separator. With the modified separator, the battery achieved a discharge capacity as high as 942 mAh g^-1 for the first cycle and remained at 90.02 mAh g^-1 after the 100th charge/discharge test at 0.1 C. Results indicate that impeding the shuttling of polysulfides contributes to efficiently improving the behavior of the Li/S battery.

Fabrication of a nanocrystal zinc oxide (ZnO)/nitrogen-doped (N-doped) graphene composite using a novel and facile in situ sol-gel technique is demonstrated. Two-dimensional nanostructure morphology with uniform ZnO nanoparticles (average diameter of 10.25 nm) anchored on N-doped graphene nanosheets was observed via electron microscopy. Because of the polar heteroatoms on the graphene sheets, an abundance sites for polysulfide absorption were provided. More importantly, the strong chemical interaction between ZnO and polysulfides efficiently hindered the transport of polysulfides. Consequently, the lithium/sulfur (Li/S) battery with the ZnO/N-doped graphene composite-coated separator delivered enhanced performance in terms of discharge capacity and cycling stability when compared to the cell with a normal separator. With the modified separator, the battery achieved a discharge capacity as high as 942 mAh g^-1 for the first cycle and remained at 90.02 mAh g^-1 after the 100th charge/discharge test at 0.1 C. Results indicate that impeding the shuttling of polysulfides contributes to efficiently improving the behavior of the Li/S battery.

A variety of myricetin derivatives bearing ferulic acid amide scaffolds were designed and synthesized. The structures of all title compounds were determined by 1 H NMR, 13 C NMR, 19 F NMR and HRMS. Preliminary bioassays suggested that some of the target compounds exhibited remarkable antiviral activities. In particular, compound 4l possessed significant protection activity against tobacco mosaic virus (TMV), with an half maximal effective concentration (EC50) value of 196.11 μg/mL, which was better than commercial agent ningnamycin (447.92 μg/mL). Meanwhile, microscale thermophoresis (MST) indicated that compound 4l have strong binding capability to tobacco mosaic virus coat protein (TMV-CP) with dissociation constant (Kd) values of 0.34 μmol/L, which was better than ningnamycin (0.52 μmol/L). These results suggest that novel myricetin derivatives bearing ferulic acid amide scaffolds may be considered as an activator for antiviral agents.

The recyclable paper based on photochromic materials not only reduces the pollution in the paper manufacture process, but also reduces the pollution caused by the use of ink, which receives wide attention. In this paper, a serial of PMoA-PWA/ZnO/PVP hybrid films which had different ratio of PMoA/PWA was prepared by the ultrasonic composite method. The results indicated that the hybrid film prepared when the ratio of PMoA to PWA was 3 had the best photochromic performance. In this system, ZnO was the photosensitizer while PMoA/PWA was the chromophore. The photochromic mechanism of PMoA-PWA/ZnO/PVP hybrid film was based on the photogenerated electron transfer mechanism. ZnO generated photoelectron under the excitation of visible light, then PMoA and PWA obtained the photoelectron and produced photoreduction reaction to generate heteropolyblue. The visible light photochromic paper was prepared by loaded PMoA-PWA/ZnO/PVP hybrid film (A3) on A4 paper. Application test showed that the prepared paper had extremely stable, excellent and reversible visible light photochromic properties, whether it was printing patterns or words and could replace the ordinary paper to realize the reuse of paper.

Using graph theory, computer aided motion, static force and power flow analysis of planetary gear mechanism is realized. The motion, static force and efficiency calculations of 6HP26 automatic transmission are carried out. Based on kinematic and static force analysis model, related matrices are acquired. Hence, kinematic and static force analysis of planetary gear mechanism is achieved. The link power can be determined by the link speed and torque. Power flow diagrams of each gear are acquired. The efficiency is calculated by transmission ratio method.

A practical method is presented to estimate rare earth elements (REE) concentrations in magmatic vapour phase (MVP) in equilibrium with water-saturated granitic melts based on empirical fluid-melt partition coefficients of REE (k_P^REE). The values of k_P^REEcan be calculated from a set of new polynomial equations linking to the chlorine molality (m_Cl^v) of the MVP associated with granitic melts, which are established via a statistical analysis on the existing experimental dataset. These equations may be applied to the entire pressure range (0.1 to 10.0 kb) within the continental crust, suggesting that light REEs behave differently in magmatic fluids, i.e. either being fluid compatible with higher m_Cl^v or fluid incompatible with lower m_Cl^v values. In contrast, heavy REEs are exclusively fluid incompatible and partition favourably into granitic melts. Consequently, magmatic fluids tend to be rich in LREE relative to HREE, leading to REE fractionation during the evolution of magmatic hydrothermal systems. Maximum k_P^REEvalue for each element is predicted and presented in a REE distribution diagram constrained by the threshold of m_Cl^v. REE contents of the granitic melt is approximated by whole-rock analysis, so that REE concentrations in the associated MVP would be estimated from the value of k_P^REE given chemical equilibrium retains. Two examples are provided respectively, to show the use of this method as a REE tracer to fingerprint the source of ore-fluids responsible for the Lake George intrusion-related Au-Sb deposit in New Brunswick (Canada), and for the Bakircay Cu-Au (-Mo) porphyry systems in northern Turkey.

In this work, the Ni/Ti/Nb multilayer composite was successfully manufactured by accumulative pack-roll bonding. The microstructure evolution and mechanical properties of the composite during the accumulative roll bonding (ARB) process were investigated by scanning electron microscopy(SEM), energy dispersive spectrometer(EDS), transmission electron microscopy (TEM), micro-hardness and tensile tests. The results showed that after 5 passes of the ARB process, the deformations of layers were relatively uniform, and no large number of interlayer fractures occurred. The microstructures of Ni and Ti were both equiaxed grains with a grain size of 200 nm and 150 nm, respectively, and finer equiaxed grains of the Ni layer were observed at the interface. The laminar structure of Nb layer was observed. The tensile strength and micro-hardness increased significantly as the number of ARB increased. After 5 passes of the ARB process, the tensile strength of the composite reached 792.3 MPa, and the micro-hardness of Ni, Ti, and Nb were increased to 270.2, 307.4, and 243.4 HV, respectively.

Spermatogonial stem cells (SSCs) are the only primitive spermatogonial cells in males that can naturally transmit genetic information to their offspring and replicate throughout their lives. Phospholipase D family member 6 (PLD6) has recently been found to be a surface marker for SSCs in mice and boars; however, it has not been validated in cattle. The results of RT-PCR and qRT-PCR found that the relative expression of PLD6 gene in the testicular tissues of 2-year-old Simmental calves was significantly higher than that of 6-month-old calves. Immunofluorescent staining further verified the expression of PLD6 protein in bovine spermatogenic cells like germ cell marker VASA. Based on multiple bioinformatic databases, PLD6 is a conservative protein which has high homology with mouse Q5SWZ9 protein. It is closely involved in the normal functioning of the reproductive system. Molecular dynamics simulation analyzed the binding of PLD6 as a phospholipase to cardiolipin (CL), and PLD6-CL complex showed high stability. The protein interaction network analysis showed that there is a significant relationship between PLD6 and piRNA binding protein. PLD6 acts as an endonuclease and participates in piRNA production. In addition, PLD6 in bovine and mouse testes has a similar expression pattern with the spermatogonium-related genes VASA and PIWIL2. In conclusion, these analyses imply that PLD6 has a relatively high expression in bovine testes and could be used as a biomarker for spermatogenic cells including SSCs.

Assessing the quality of corn seeds necessitates evaluating their content of water, fat, protein, and starch. This study integrates hyperspectral imaging technology with chemometric analysis techniques to achieve non-invasive and rapid detection of multiple key components in corn seeds. Hyperspectral images of the embryo surface of maize seeds were collected within the wavelength range of 1100~2498nm. Subsequently, image segmentation techniques were applied to extract the germ structure of the corn seeds as the region of interest. Seven spectral data preprocessing algorithms were employed, and the Detrending Transformation (DT) algorithm was identified as the optimal preprocessing method through comparative analysis using the Partial Least Squares Regression (PLSR) model. To reduce spectral redundancy and streamline the prediction model, three algorithms were employed for characteristic wavelength extraction: Successive Projections Algorithm (SPA), Competitive Adaptive Reweighted Sampling (CARS), and Uninformative Variable Elimination (UVE). Using both the original spectra and the extracted characteristic wavelengths, four content detection models were constructed: PLSR, Back Propagation Neural Network (BPNN), Radial Basis Function Neural Network (RBFNN), and Least Squares Support Vector Machine (LSSVM). The experimental results demonstrate that the DT-CARS-LSSVM model exhibits exceptional accuracy and stability in predicting these four key components, with determination coefficients of 0.9877, 0.9344, 0.9827, and 0.9592, respectively. This study not only provides a scientific basis for evaluating the quality of corn seeds but also opens up new avenues for the development of non-invasive detection technology in related fields.

With the development of Global Navigation Satellite Systems (GNSS), the quality and anti-jamming capability of satellite navigation signals are crucial. Binary Offset Carrier (BOC) modulation faces issues of false locking due to multi-peak ambiguity in its autocorrelation function, limiting its application. This paper examines FH-BOC modulation, which integrates BOC with frequency hopping technology, significantly improving anti-jamming, anti-multipath performance, and spectral efficiency. To meet the high dynamic tracking demands of FH-BOC signals, this study explores three types of carrier tracking loops: the traditional second-order frequency-locked loop assisted a third-order phase-locked loop, a linear Kalman filter-based tracking algorithm, and an adaptive Kalman filter-based tracking algorithm. A composite code tracking loop is also proposed. Simulations show that the adaptive Kalman filter algorithm achieves high-precision carrier tracking in dynamic environments and quickly converges during transitions. The composite code tracking loop, aided by the carrier loop, ensures precise synchronization of pseudocode and frequency-hopping subcarrier phases, demonstrating the superior performance of FH-BOC modulation in dynamic environments.

：Non-Euclidean data, such as social networks, and citation relationships between documents, has node information and structural information. Graph Convolutional Network(GCN) can automatically learn node features and association information between nodes. The core ideology of the graph convolutional network is to aggregate node information by using edge information, thereby generating a new node feature. In the process of updating node features, there are two core influencing factors. One is the number of neighboring nodes of the central node, the other is the contribution of the neighboring nodes to the central node. Due to the previous GCN methods not simultaneously considering the numbers and different contributions of neighboring nodes to the central node, we design the Adaptive Attention Mechanism(AAM). To further enhance the representational capability of the model, we utilize Multi-Head Graph Convolution(MHGC). Finally, we adopt cross-entropy(CE) loss function to describe the difference between the predicted results of node categories and the ground truth (GT). Combined with backpropagation, this ultimately achieves accurate node classification. Based on AAM, MHGC and CE, we contrive the novel Graph Adaptive Attention Network (GAAN). Experiments show that the classification accuracy has achieved outstanding performances on Cora, Citeseer and Pubmed datasets.

The existing segmentation-based scene text detection methods mostly need complicated post-processing, and the post-processing operation is separated from the training process, which greatly reduces the detection performance. The previous method, DBNet successfully simplified post-processing and integrated the post-processing into a segmentation network. However, the training process of the model took a long time for 1200 epochs and the sensitivity to texts of various scales was lacking, leading to some text instances being missed. Considering the above two problems, we design the text detection Network with Binarization of Hyperbolic Tangent(HTBNet). First of all, we propose Binarization of Hyperbolic Tangent (HTB), optimized along with which, the segmentation network can expedite the initial convergent speed by reducing the amount of epochs from 1200 to 600. Because features of different channels in the same scale feature map focus on the information of different regions in the image, to better represent the important features of all objects in the image, we devise the Multi-Scale Channel Attention(MSCA). Meanwhile considering that multi-scale objects in the image cannot be simultaneously detected, we propose a novel module named Fused Module with Channel and Spatial(FMCS), which can fuse the multi-scale feature maps from channel and spatial dimension. Finally we adopt cross entropy as the loss function, which measures the difference between predicted values and ground truths. The experimental results show that HTBNet compared with lightweight models has achieved competitive performance and speed on Total-Text(F-measure:86.0%, FPS:30) and MSRA-TD500 (F-measure:87.5%, FPS:30).

Neonicotinoids (NEOs) have become the most widely used insecticides in the world since the mid-1990s. According to Chinese dietary habits, rice and water are usually heated before being consumed, but the information about the alteration through the heat treatment process is very limited. In this study, the parents of NEOs (p-NEOs) accounted for >99% of the total NEOs mass (∑NEOs) in both uncooked (median: 66.8 ng/g) and cooked (median: 41.4 ng/g) rice samples from Guangdong Province, China, while the metabolites of NEOs (m-NEOs) involved in this study accounted for less than 1%. We aimed to reveal the concentration changes of NEOs through heat treatment process, thus, several groups of rice and water samples from Guangdong were cooked and boiled, respectively. Significant (p < 0.05) reductions in acetamiprid, imidacloprid (IMI), thiacloprid, and thiamethoxam (THM) have been observed after the heat treatment of the rice samples. In water samples, the concentrations of THM and dinotefuran decreased significantly (p < 0.05) after the heat treatment. These results indicate the degradation of p-NEOs and m-NEOs during the heat treatment process. However, the concentrations of IMI increased significantly in tap water samples (p < 0.05) after heat treatment process, which might be caused by the potential IMI precursors in those industrial pesticide products. The concentrations of NEOs in rice and water can be shifted by the heat treatment process, so this process should be considered in relevant human exposure studies.

This paper aims to explore the relationship between airfoil deformation and airfoil aerial-aquatic adaptation. The form of “flexible skin and rigid drive structura” holds immense potential for various applications. In this study, we utilize the B-spline method to parametrically describe the airfoil shape. An airfoil deformation parameterization method is proposed based on the isogeometric method. This method allows us to depict airfoil deformation as the position and displacement of the driving point, enabling an expression of the flexible skin's deformation driven by the internal structure. We utilize the Xfoil application and Gaussian regression method to elucidate the relationship between driving point position and displacement and the airfoil's dynamic performance. Additionally, we employ the Sobol method to assess the sensitivity of the driving point variables to the airfoil's dynamic performance. Our findings indicate that the attack angle of the airfoil exhibits the highest sensitivity index to the airfoil's dynamic performance. Furthermore, variables of the driving point situated at the leading and trailing edges of the lower surface significantly impact the airfoil lift coefficient, those located at the mid-section of the upper surface have a considerable effect on the airfoil drag coefficient.

The intense motion of a ship can greatly impacts the comfort of crew members and the safety of the vessel. Therefore, accurately estimating and predicting ship attitudes has become an important issue. This paper introduces the latest development in functional deep learning model called DeepOnet. It takes wave height as input and ship motion as output, using a cause-to-result prediction approach. The modeling data used in this study is sourced from publicly available experimental data from the Iowa Institute of Hydraulic Research. Firstly, parameters system tuning was conducted for the neural network's hyperparameters to determine the appropriate combination of parameters. Secondly, the DeepOnet model for wave height and multi-degree-of-freedom motion was established, and the influence of increasing time steps on prediction accuracy was examined. Finally, a comparison was made between the DeepOnet model and the classical time series model LSTM. It was found that the DeepOnet model had a 10-fold improvement in accuracy for roll and heave attitudes. Moreover, as the forecast duration increased, the advantage of DeepOnet showed a trend of strengthening. As a functional prediction model, DeepOnet provides a new promising tool for very short-term prediction of ship motion.

The degree of ore rock fragmentation of mine blasting is an important index for evaluating the effect of engineering blasting. In order to study the effect of millisecond delayed blasting on the internal fragmentation of the ore rock, LS-DYNA numerical simulation software was used to obtain the damage characteristics of the ore rock in the blasting area using the RHT model. The Mohr-Coulomb strength damage criterion was applied to analyze the internal stress state of the ore rock, and the effects of 25ms, 50ms and 75ms delay time conditions on ore rock fragmentation were studied. The results show that, within a certain range of delay time, the degree of rock fragmentation increases with the increase of delay time. The stress state in the ore rock due to blasting is strengthened with the increase of delay time in the direction of the blast hole, which shows that the stress concentration is strengthened from the excavation face to the interior of the ore rock. The damage and the degree of fragmentation show a characteristic relationship of 25ms＜50ms＜75ms, which is verified by carrying out blasting experiments on site.

In (Semigroup Forum 77: 325-338, 2008) Mahmoudi M. and Renshaw J. solved a study that covers of cyclic $S$-acts over monoids. This article is an attempt to initiate the covers of finitely generated $S$-acts. We give a necessary and sufficient condition for a monoid to have the properties that $n$-generated $S$-acts have strongly flat covers, Condition $(P)$ covers and projective covers. The main conclusions extend some known results. We show also that Condition $(P)$ covers of finitely generated $S$-acts are not unique, unlike the situation for strongly flat covers. Additionally, we demonstrate that the property of Enochs' $\mathcal{X}$-precover of $S$-act $A$, where $\mathcal{X}$ denotes a class of $S$-acts that are closed under isomorphisms.

Aiming to diminish the defects caused by high-speed pulsed GMAW welding, such as non-penetration, non-fusion, humping and undercut, the paper proposed an improved twin-wire double-pulsed high-speed welding process by introducing the impact of additional shielding gas on the welding pool and the effects of different shielding gas flowrates on the microstructure and mechanical properties of the welded seam was investigated. The 2205 duplex stainless steel plate was used as the base material for the butt welding test, and the welded seams were subjected to tensile test, metallographic analysis, hardness analysis, and nondestructive testing. The results indicate that as the flowrate of additional shielding gas increases in the range of 8 L/min~16 L/min, the width of the welded seam increases and the height of reinforcement decreases gradually. However, a grooved seam with a lower middle region and higher sides will appear when the gas flowrate becomes excessively large. The test results indicate that the jet impact force is relatively moderate when the flowrate of the additional shielding gas is 12 L/min and thus, is optimal for the welded seam.

In the neuroscience research field, specific for medical imaging analysis, how to mining more latent medical information from big medical data is significant for us to find the solution of diseases. In this review, we focus on neuroimaging data that is functional Magnetic Resonance Imaging (fMRI) which non-invasive techniques, it already becomes popular tools in the clinical neuroscience and functional cognitive science research. After we get fMRI data, we actually have various software and computer programming that including open source and commercial, it's very hard to choose the best software to analyze data. What's worse, it would cause final result imbalance and unstable when we combine more than software together, so that's why we want to make a pipeline to analyze data. On the other hand, with the growing of machine learning, Python has already become one of very hot and popular computer programming. In addition, it is an open source and dynamic computer programming, the communities, libraries and contributors fast increase in the recent year. Through this review, we hope that can make neuroimaging data analysis more easy, stable and uniform base the one platform system.

In the realm of Lithium-ion batteries, issues like material aging and capacity decline contribute to performance degradation or potential safety hazards. Predicting Remaining Useful Life (RUL) serves as a crucial method to assess the health of batteries, thereby enhancing reliability and safety. Currently hybrid approaches for batteries RUL estimation are prevalence and gained fruitful development. In this paper, a hybrid voting ensembles combining Gradient Boosting, Random Forest and K-Nearest Neighbors is proposed to predict the capacity fade trend and knee point. Finally, extensive experiments are conducted using CALCE CS2 datasets. According to the experimental results, the proposed approach supersedes the single deep learning approach for RUL prediction and the knee point is predicted accurately. Besides prediction purpose, this innovated approach can be also proposed to be integrated into the real-world application for wider usage.

Optical network monitoring and soft failure identification such as optical filter shifting and filter tightening is increasingly significant in the future complex and dynamic optical networks. Center frequency shift of optical filtering device in optical network has a serious impact on the perfor-mance of multi-span transmission, especially in high spectrum efficiency faster-than-Nyquist (FTN) transmission systems with various optical switching and add/drop nodes. Existing moni-toring schemes generally have problem of high cost, high complexity and the inability to realize multi-channel online monitoring, which makes it difficult to be applied in wavelength division multiplexing (WDM) system with numerous nodes. In this paper, a monitoring scheme of fre-quency shift of optical filtering devices based on optical label (OL) is proposed and demonstrated. The signal spectrum of each channel is intentionally divided into many sub-bands with corre-sponding optical labels loading. The characters of spectrum power changing caused by frequency shift can be reflected on labels power changing of each sub-band, which are used to monitor and estimate the value of frequency shift by DSP algorithm. Simulation results shows that the that the monitoring errors of frequency shift can be kept below 0.5GHz reasonably after 10-span WDM transmission in FTN polarization multiplexing m-ary quadrature amplitude modulation (PM-mQAM) systems. In addition, 250km fiber transmission experiments are also carried out and the similar results are obtained, which further verify the feasibility of our proposed scheme. The characters of low cost, high reliability and efficiency make it a better candidate for practical ap-plication in the future FTN WDM networks.

In this paper, we study the well-posedness and asymptotics of a one-dimensional thermoelastic laminated beam system either with or without structural damping, where the heat conduction is given by Fourier's law effective in the rotation angle displacements. We show that the system is well-posed by using Lumer-Philips theorem, and prove that the system is exponentially stable if and only if the wave speeds are equal, by using the perturbed energy method and Gearhart-Herbst-Prüss-Huang theorem. Furthermore, we show that the system with structural damping is polynomially stable provided that the wave speeds are not equal, by using the second-order energy method.

A PLS-based quality prediction method is proposed for batch processes using two-dimensional extended windows. To realize the adoption of information in the direction of sampling time and batch, a new definition region of support (ROS), k-i-back-extended region of support (KIBROS), is proposed to establish the extended window, which including the data of the previous sampling times in the same batch, the data of the same sampling time in the historical batches, the data of the previous sampling times in the historical batches and the data of the later sampling times in the historical batches. According to these regions of support, extended windows are established, and different models are proposed based on the extended windows for batch processes quality prediction. Further, using a typical batch process as an example, the injection molding process, the proposed quality prediction method is experimentally verified, proving that the proposed methods have higher prediction accuracy than the traditional method and the prediction stability is also improved.

As a universal pathogen leading to neonatal defects and transplant failure, Human cytomegalovirus (HCMV) has strict species specificity that the inability to using this virus in animals has hampered its pathogenesis study. However, the mechanism of cross-species barrier remains elusive that no non-human cell model has been established to fill this knowledge gap. We observed that primary dermis fibroblasts (TSDF) isolated from the Chinese tree shrew (Tupaia belangeri chinensis), a small laboratory animal with close affinity to primates, were permissive to HCMV replication. In TSDF infected with GFP-expressing HCMV, the green fluorescence and cytopathic effect were observed and the expression of 3 kinetic genes and replication of viral genome were detected. The cell-free viruses produced in TSDF reached 103 pfu/mL at 96 hpi, which were 10-fold lower than in primary human foreskin fibroblasts. Our results demonstrated that TSDF supported low level of lytic replication of HCMV. The TSDF model provides a useful platform for the mechanism study of species barrier of HCMV.

Micro/Nano Robot is an intelligent and efficient microrobot that can perform specific tasks under the influence of external stimuli. Depending on the application scenarios, the microrobot can adaptively transform into appropriate functional forms under different external stimuli, thus perfectly matching the needs. To date, microbots have been widely used in targeted therapy, drug delivery, tissue engineering, environmental remediation, and other fields. Although the applications of microrobots are promising, there are only a few reviews that can focus on the preparation methods and driving mechanisms. Therefore, it is necessary to outline the current status of the development of these microrobots in order to provide some new insights for the further development of the field. Therefore, this paper reviews the research progress of microrobots in terms of preparation methods, stimulus response mechanisms and applications, and highlights the applicability of different preparation methods and stimulus types. Finally, the current challenges faced by microrobots are highlighted and possible solutions are proposed to facilitate the practical application of microrobots.

Salidroside, a valuable phenylethanoid glycoside, is obtained from plants belonging to the Rhodiola genus, known for its diverse biological properties. At present, salidroside is still far from large-scale industrial production due to the lower titer and higher process cost. In this study, we constructed a biosynthetic pathway from L-tyrosine to salidroside in Saccharomyces cerevisiae. To increase sali-droside production, we for the first time constructed an in vivo UDP-glucose regeneration system that sucrose synthase GmSUS worked in conjunction with UDP-glucose transferase RrUGT33 to improve the UDP-glucose availability with inexpensive sucrose as the consumed substrate. Finally, the molar conversion rate of L-tyrosine could reach 95%. To further reduce the cost, co-culture with E. coli that synthesized L-tyrosine de novo resulted in an 81% reduction in the final substrate cost per 1 kg of salidroside compared to the initial cost. The final titer of salidroside obtained 3.8 g/L and was the highest titer achieved at the Shake-Flask-Level in the existing reports. And this marked the first successful synthesis of salidroside in an in situ enhanced UDP-glucose system using sucrose. This accomplishment laid a robust groundwork for further investigations into the synthesis of other notable glycosides and natural compounds.

Aiming at the problems of inaccurate segmentation of long object and information loss of small object in real-time semantic segmentation algorithm, this paper proposes a lightweight multi-branch real-time semantic segmentation network based on BiseNetV2. The new auxiliary branch makes full use of spatial details and context information to cover the long object in the field of view. Meanwhile, in order to ensure the inference speed of the model, the asymmetric convolution is used in each stage of the auxiliary branch to design a structure with low computational complexity. In the multi-branch fusion stage, the alignment and fusion module is designed to provide guidance information for deep and shallow feature mapping, so as to make up for the problem of feature misalignment in the fusion of information at different scales, and thus reduce the loss of small target information. In order to further improve the model’s awareness of key information, a global context module is designed to capture the most important features in the input data. The proposed network uses NVIDIA GeForce RTX 3080 Laptop GPU experiment, on the road street view data set Cityscapes and CamVid average occurring simultaneously ratio reached 77.1% and 78.4% respectively, with running speed of 127 frames/s respectively and 112 frames/s. The experimental results show that the proposed algorithm can achieve real-time segmentation and improve the accuracy significantly, showing good semantic segmentation performance

A novel metal-doped carbon quantum dot, zinc-chlorine co-doped carbon quantum dots (Zn/Cl-CQDs), has been developed for the fluorescent probe detection of vitamin B2 and the analysis of the correlation properties of this carbon quantum dot and vitamin B2. Stability experiments demonstrate that Zn/Cl-CQDs possess good fluorescence properties under alkaline conditions. However, when vitamin B2 is added into Zn/Cl-CQDs, the fluorescence intensity decreases sharply, indicating that a fluorescence quenching phenomenon occurs between vitamin B2 and Zn/Cl-CQDs. Lastly, the use of Zn/Cl-CQDs in the detection of vitamin B2 tablets and vitamin B2-rich fruits resulted in recovery rates of 98.2% and 100.6%, respectively. Therefore, this method can be well applied to the detection and analysis of vitamin B2, and has great development prospects in the pharmaceutical industry and food monitoring fields.

Nitrile butadiene rubber (NBR) and its various composites are extensively studied as matrix materials for oil-free lubricated mechanical friction surfaces. While numerous macroscopic friction experiments can compare the frictional performance of different NBR composites, the complex material preparation and low experimental efficiency pose challenges. Nanoscale molecular dynamics (MD) simulations can help develop materials with improved friction properties, but they cannot directly provide the friction coefficients of actual macroscopic friction surfaces. Therefore, it is important to integrate the advantages of macroscopic and nanoscale friction studies and perform a synergistic analysis to modify the friction properties of composite materials. In this study, a multi-scale approach is proposed to simulate the frictional characteristics of carbon nanotube (CNT)-reinforced NBR by combining the MD friction simulation， micromechanical bridging model, and macroscopic finite element analysis (FEA) methods. The results of the multi-scale friction simulation of copper (Cu)-CNT/NBR composites show that the addition of CNTs significantly improves the frictional properties of NBR, and the extent of the improvement is related to the mass fraction of CNTs. As the mass fraction of CNTs increases (0%, 1.25%, 2.5%, 5%), the coefficient of friction decreases from 0.50 to 0.38. The results are validated by ring-block friction experiments at the same scale as the simulations.

The tourism economy plays an essential role in supporting and driving tourism development. Therefore, studying its resilience is crucial for promoting sustainable and high-quality tourism development. Based on the core essentials of economic toughness, this paper constructs the tourism economic toughness evaluation index system, uses the entropy weight TOPSIS method to measure the tourism economic toughness of 10 counties and cities in the Yili River Valley in 2010-2019, analyzes its spatio-temporal evolution characteristics through the standard deviation ellipse, the traditional Markov chain, and the spatial Markov chain, and uses the grey correlation analysis method to analyze the driving factors of the tourism economic toughness. The results show that: (1) the economic resilience of tourism in the Yili River Valley shows a "W"-shaped time-series dynamic development trend with an average index of 0.28394, in which it experienced a decline from 0.28 to 0.27 during 2012-2013 and 2015-2016; (2) Spatial Pattern: The Yili River Valley tourism economic resilience is characterized by a clear uneven spatial distribution. The city of Yining, representing the northwestern region, exhibits a high level of resilience, while the southwestern region, endowed with rich tourism resources, demonstrates a medium level of resilience. Conversely, the central to southeastern counties and cities, such as ChabuchaerXibo Autonomous County and other counties and cities, are characterized by a lack of developed tourism facilities, which has resulted in a lower level of resilience and a weak development situation; (3) In terms of spatial and temporal evolution, the standard deviation ellipse is stabilized year by year pointing to "northwest-southeast", the clustering tendency is gradually enhanced, and five tourism economic resilience convergence clubs are identified, whose internal transition probability is significantly affected by spatial location, and which show obvious stability and neighborhood effects; (4) Regarding the driving factors, the impact of each driving factor on the resilience of the tourism economy reaches the statistical significance threshold of 0.77 or above. Among them, the number of employees in the tertiary industry, especially the input of high-quality talents in the tourism industry, plays a key role in improving the quality of tourism services and strengthening the industry's ability to withstand risks and development potential.

Functional partially linear regression model, contains a functional linear part and a non-parametric part, in which testing the linear relationship between the response and the functional predictor is of fundamental importance. When functional data cannot be approximated with a few principal components, based on a pseudo estimate for the unknown non-parametric component, we develop a U-statistic of order-two in this paper. Under some regularity conditions, we use the martingale central limit theorem to prove that the proposed test statistic is asymptotically normal. The finite sample performance with simulation studies and real data application are assessed to verify the proposed test procedure.

Amid escalating urbanization, devising rational commercial space layouts is a critical challenge. Leveraging machine learning, this study uses a Back-propagation (BP) neural network to optimize commercial spaces in Weinan City's central urban area. The results indicate an increased number of commercial facilities with a trend of multi-centered agglomeration and outward expansion. Based on these findings, we propose a strategic framework for rational commercial space development emphasizing aggregation centers, development axes, and spatial guidelines. This strategy provides valuable insights for urban planners in small and medium-sized cities in the Yellow River Basin and metropolitan areas, ultimately showcasing the power of machine learning in enhancing urban planning.

The current outbreak of coronavirus disease (COVID-19) caused by SARS-CoV-2 in Wuhan, China has killed more than 2600 people since December 2019. Currently there is no effective treatment for this epidemic. Drug for anti SARS-CoV-2 are urgently needed. In this study we evaluated two compound libraries containing launched drugs and compounds from 300 kinds of Traditional Chinese Medicine in order to find anti SARS-CoV-2 drugs. Docking and then calculating binding free energy were performed as workflow against four key anti-SARS-CoV-2 drug targets, 3CLpro, PLpro and RdRp from SARSCoV-2, and AAK1 from human as well. As a result, drugs launched with potential for antiviral usage were selected in the hope of providing some knowledge for future drug discovery.

Differences in the physical and chemical properties of reclaimed water (RW) and natural surface water (SW) lead to the differences in terms of nitrogen and phosphorus release when pipeline sediments enter these water bodies. The nitrogen and phosphorus release kinetics from pipe sediments with different particle sizes have been investigated. The results demonstrated that both SW and RW had a pH buffering effect after sediment addition, and the final pH (approximately 8.1) of RW was lower. The release of total phosphorus (TP) and ammonia nitrogen ( NH₄⁺-N) fitted the first-order kinetic model where the release of TP reached equilibrium; TP release was inhibited in both SW and RW, where RW exhibited the lowest (by a factor of 1.23~2.44) release (0.002 mg/g). The release of NH4+-N was promoted in both SW and RW; the maximum release in RW was 0.0188 mg/g. The amounts of NH₄⁺-N released in SW and RW were 1.02-1.40 and 1.30-1.80 times that of the control group (CG), respectively. The percentage of TP and NH₄⁺-N release in the three groups was highest in 75-154 μm pipe sediment, reaching 34.53% and 43.51% in SW and RW, respectively. These results can assist in the development of water quality evolution models for specific urban scenarios, and provide important guidance for the precise regulation of recharge water quality during and after rainfall.

Topology optimization is a pioneering design method that can provide various candidates with high mechanical properties. However, the high-resolution for the optimum structures is highly desired, normally in turn leading to computationally intractable puzzle, especially for the famous Solid Isotropic Material with Penalization (SIMP) method. In this paper, an efficient and high-resolution topology optimization method is proposed based on the Super-Resolution Convolutional Neural Network (SRCNN) technique in the framework of SIMP. The SRCNN includes four processes, i.e. refining, path extraction & representation, non-linear mapping, and reconstruction. The high computational efficiency is achieved by a pooling strategy, which can balance the number of finite element analysis (FEA) and the output mesh in optimization process. To further reduce the high computational cost of 3D topology optimization problems, a combined treatment method using 2D SRCNN is built as another speeding-up strategy. A number of typical examples justify that the high-resolution topology optimization method adopting SRCNN has excellent applicability and high efficiency for 2D and 3D problems with arbitrary boundary conditions, any design domain shape, and varied load.

Robotic systems have been widely used in various industries, so the security of communication between robots and their components has become an issue that needs to be focused on. As a framework for developing robotic systems, the security of ROS2 can directly affect the security of the upper-level robotic systems. Therefore, it is a worthwhile research topic to detect and analyze the security of ROS2. In this paper, we adopt a formal approach to analyze the security of the communication mechanism of ROS2. First, we use a state transition system to model the potential vulnerabilities of ROS2 based on the ROS2 communication mechanism and the basic process of penetration testing. Secondly, we introduce the CIA model on the basis of the established vulnerability model and use LTL to define its security properties. Then, we design and implement a vulnerability detection tool for ROS2 applications based on the vulnerability model and security properties. Finally, we experimentally test some ROS2-based applications, and the results show that ROS2 has vulnerabilities without additional protection safeguards.

This study investigated the effect of replacing part of the dietary soybean meal with either polymer-coated urea or gelatinized starch urea on the performance, nutrient digestibility, blood biochemical indexes, ruminal fermentation and rumen microflora of Angus heifers. The urea release profiles of two kinds of slow-release urea were evaluated in vitro and indicated a superior nitrogen retention with the polymer-coated urea. 210 purebred Angus cattle (BW = 314.26 kg) were divided into three groups: no urea group (CON), polymer-coated urea group (PCU), gelatinized starch urea group (GSU), 20g/kg polymer-coated urea or 25g/kg gelatinized starch urea was used to replace part of soybean meal in the concentrate feed respectively according to the principle of iso-metabolic energy and iso-nitrogenous. During the whole experiment, the ADG of PCU group was higher than both the GSU group and the CON group. The feed-weight ratio of the PCU group was significantly lower than both the GSU group and the CON group during the 90-day feeding period. The ADF apparent digestibility in the PCU group was significantly higher than that of the CON group, and extremely significantly higher than that of the GSU group. On the 86th day, the ALB content in the PCU group was significantly higher than that in the CON group. The contents of acetic acid and butyric acid, total volatile fatty acid and propionic acid were significantly higher in the PCU group than in the CON group. Bacterial diversity analysis found that the abundance of Firmicutes was higher in the PCU group than that in the GSU group and the CON group at the phylum level, and inverse result was observed in Bacteroidetes. The abundance of Paraprevotella was higher in the PCU group, whereas higher abundance of Prevotella was found in the GSU group at the genus level. These results indicate that both polymer-coated urea and gelatinized starch urea can replace part of soybean meal in the diet, and the amount of substitution in this trial had no diverse effect on the performance of Angus heifers, and the effect and economic benefits brought by polymer-coated urea were better than gelatinized starch urea.

Geological structures such as joints and faults in rock mass have significant influence on open pit mining. Hence, it is critical to develop a understanding of dynamic joint behaviour under blasting loading. This in turn can provide both theoretical and practical guidance to improve blasting rock fragmentation and associated bucket excavating efficiency. In this paper, delayed blasting on the highwall bench at Baiyunebo open-pit mine was used as an example, a nonlinear joint blasting model was also constructed. By simplifying the blasting wave propagation velocity, the P-wave normal incidence to the joint was obtained. The peak vibration velocity was 0.33m/s at 3.0s. The S-wave reflected by the joint interface was first reflected backward and then forward, which the peak vibration velocity was 0.027 m/s. By combining the relevant stress and displacement theories of type I and II cracks, the equipotential diagrams of the stress and displacement field with the vibration velocity of the particle were obtained. σx was positive in the direction of 0~330° and subjected to tensile stress, whereas σy was positive in the direction of 0~180° and under tensile stress. The longitudinal σy along joint was low in compressive stress distribution area and did not affect surrounding rock at the time. The stress concentration appeared in the lower right corner. Based on the continuous behavior of stress wave in joints, the asymmetry and continuous changes reflected in the whole process could not be analysed by the contour diagram. Hence, ANSYS used to analyse distribution of the stress field. The intensity of the shock wave after detonation was greater than that of the rock strength. Subsequently, the sub-layer shock wave supplemented the shock wave energy that was not enough to break the rock and induced further cracking. This was able to be visualized by the degree of color change post-processing. It was concluded that with the attenuation of the detonation wave energy, the stress exhibited a decreasing trend in this process. According to distribution of the peak effective stress, it was found that the peak value first increased to 10-12 MPa and then showed a downward trend. Overall, the results were validated against the finite element simulation and mathematical analysis.

Container crane has been widely used for port operation. However, the structure of port container crane is large, which always lead to crane damage under the vibration and strong wind. Therefore, a method for vibration reduction of container crane structure based on particle damping technology is proposed. In this investigation, the scale 1:80 crane model is built, the equivalent mechanical model is also established to preliminary verify the effect of vibration suppression. Furthermore, the dependence of vibration suppression effect on the key parameters of the damper, i.e., filling material, filling rate, particle size, and installation position of dampers are analyzed through experiments. The results indicate that the vibration peak of the crane structure displayed in Simulink oscilloscope is weakened and lags behind, the installation of the damper brings the effect of vibration suppression for the crane, the vibration suppression effect reaches 25%; the crane mode obtains the best vibration suppression effect under the condition that the material filled in the damper has a large density and elastic modulus, sufficient collision space and high collision frequency, and the dampers are installed far away from the crane center of gravity. The optimum parameters of the damper obtained from experiments, 12 mm lead beads, filling rate of 60%, installed in the distal ends within the strength range of the forearm of the crane. It is thus concluded that the particle damping technology has provided an effective way in wind and vibration reduction for container crane.

In high-risk railway construction, personal protective equipment monitoring is critical but challenging due to small and frequently obstructed targets. We propose YOLO-EA, an innovative model that enhances safety measure detection by integrating ECA into its backbone's convolutional layers, improving discernment of minuscule objects like hardhats. YOLO-EA further refines target recognition under occlusion by replacing GIoU with EIoU loss. YOLO-EA's effectiveness was empirically substantiated using a dataset derived from real-world railway construction site surveillance footage. It outperforms YOLOv5, achieving 98.9% precision and 94.7% recall, up 2.5% and 0.5% respectively, while maintaining real-time performance at 70.774 fps. This highly efficient and precise YOLO-EA holds great promise for practical application in intricate construction scenarios, enforcing stringent safety compliance during complex railway construction projects.

This study presents an exploration into identifying the interactions between ocean waves and the continental margin in the origination of double-frequency (DF, 0.1-0.5 Hz) microseisms recorded at 33 stations across East Coast of USA (ECUSA) during a ten-day period of ordinary ocean wave climate. Daily primary vibration directions are calculated in three frequency bands and projected as great circles passing through each station. In each band, the great circles from all stations exhibit largest spatial density primarily near the continental slope in the western North Atlantic Ocean. Generation mechanisms of three DF microseism events are explored by comparing temporal and spatial variations of the DF microseisms with the migration patterns of ocean wave fronts in Wavewatch III hindcasts. Correlation analyses are conducted by comparing the frequency compositions of and calculating the correlation coefficients between the DF microseisms and the ocean waves recorded at selected buoys. The observations and analyses lead to a hypothesis that the continental slope causes wave reflection, generating low frequency DF energy and that the continental shelf is where high frequency DF energy is mainly generated in ECUSA. The hypothesis is supported by the primary vibration directions being mainly perpendicular to the strike of the continental slope.

Species data of 249 National Nature Reserves in China was used to identify potential underlying drivers of latitudinal gradients in plant diversity. We used generalized linear models (GLMs) to assess the correlations between predictor and response variables. We also used SAM (Spatial Analysis in Macroecology) to eliminate autocorrelation along each of the 249 studied locations. We used the Akaike information criterion (AICc; Montoya et al. 2007) to select the independent variables were those included in the best models from different combinations of climate, habitat and animal variables. Variance partitioning was used to decompose the variation in plant richness across different taxonomic levels among the three groups of predictors. We found that: Total plant species, gymnosperms, angiosperms and ferns showed significant latitudinal trends in richness (p < 0.001). Water-energy and habitat variables generally explained more variation in richness across different plant groups than did animal richness. Annual precipitation was selected as the best water-energy variable across different taxonomic plants groups, soil PH and elevation range were selected as the best habitat variables across different taxonomic plant groups. The independent effects of habitatvariables were higher than that of water-energy and animal variables across different taxonomic plants groups. Water-energy, habitat heterogeneity, and animal variables explain 48.8% of the variation in total species richness, 28.2% in gymnosperm richness, 44.2% in angiosperm richness, and 38.9% in fern richness.Plants showed significant latitudinal trends in richness (p < 0.001). Water-energy and habitat variables generally explained more variation in richness across different taxonomic plants groups than did animal variables. The independent effects of habitat variables were higher than those of water-energy and animal variables across different taxonomic plants groups.

Moisture and thermal are the key factors for influencing methane desorption during CBM exploitation. Using high pressure water injection technology into coalbed, new fractures and pathways are formed to methane transport. It is existed a phenomenon of water inhibiting gas flow. This study is focused on various water pressures impacted on gas adsorbed coal samples, then the desorption capacity could be revealed under different conditions. And the results are shown that methane desorption capacity was decreased with water pressure increased at room temperature and the downtrend would be steady until water pressure was large enough. Heating could promote gas desorption capacity effectively, with the increasing of water injection pressures, the promotion of thermal on desorption became more obvious. These results are expected to provide a clearer understanding of theoretical efficiency of heat water or steam injection into coalbed, they can provide some theoretical and experimental guidance on CBM production and methane control.

The new digital infrastructure has become an important basis for the green development of agriculture. This paper selects provincial sample data from 2006 to 2022, constructs an indicator system to measure new digital infrastructure and agricultural green total factor productivity, and explores how new digital infrastructure can promote agricultural green development. The results show that: (1) the new digital infrastructure has a significant role in promoting the green development of agriculture, and this conclusion is still valid after processing endogeneity and heteroscedasticity; (2) Technology and land factors play an intermediary role in the promotion of green agricultural development by the new digital infrastructure, that is, the new digital infrastructure helps to improve the quality and technical level of cultivated land and thus promote green agricultural development; (3) Labor force factors optimize the mediating role of technology factors, that is, the higher the quality of labor force, the stronger the role of the new digital infrastructure in promoting the green development of agriculture through the technological path; (4) The effect of new digital infrastructure on the green development of agriculture is obviously heterogeneous, and the effect is more obvious in northwest China and the regions with lower marketization level, higher environmental regulation level. This study is helpful to clarify the relationship between new digital infrastructure and agricultural green development in China, and provide corresponding policy suggestions for promoting regional agricultural green development.

This study establishes a multivariate function model for natural human load carrying walking in some typical scenarios like college equipments and materials relocation for students. For classified materials relocation needs and constraints, we obtain the relationship between walking speed and load weight for single person, as well as the time cost for different round trips. By establishing an integer programming model with the minimum total transportation time cost and quality assurance as the objective function and the requirements of negative weight and speed as the constraints conditions, we reach the optimal item allocation methods considering time cost and shelf life were obtained. We discover that there is an approximate linear relationship between the change in natural walking speed and travel time when the load is small, thus obtaining the time cost of student transportation under different round-trip situations. The Monte Carlo simulation algorithm is used to obtain the optimal allocation scheme that meets the efficiency and quality requirements. The analysis methods and results can be used as guidance for task scheduling optimization for material relocation in educational organizations as well as commercial agencies.

This study derives space travel pricing by Walrasian Equilibrium, which is logical reasoning from the general relativity theory (GRT), the accounting equation, and economic supply and demand functions. The Cobb-Douglas functions embed the endogenous space factor as new capital to form the space travel firm's production function, which is also transformed into the consumer's utility function. Thus, the market equilibrium occurs at the equivalence of supply and demand functions, like the GRT presents the equivalence between the spatial geometric tensor and the energy-momentum tensor, which explains the principles of gravity and the motion of space matter in the spacetime framework. The mathematical axiomatic set theory of the accounting equation explains the equity premium effect that causes a short-term accounting equation inequality, then reaches the equivalence by suppliers' incremental equity through the closing accounts process of the accounting cycle. On the demand side, the consumption of space travel can be assumed as a value at risk (VaR) investment to attain the specific spacetime curvature in an expected orbit. Spacetime market equilibrium is then achieved to construct the space travel pricing model. The methodology of econophysics and analogy method was applied to infer the space travel pricing by the model of profit maximization, single-minded, and envy-free pricing in unit-demand markets. A case study with simulation was conducted for empirical verification of the math models and algorithm. Results show that space travel pricing remains the principle of market equilibrium but needs to be extended to the spacetime tensor of GRT.

To promote low-carbon and green travel, this study proposes a tripartite evolutionary game model among new energy vehicle manufacturers, consumers, and government agencies. The game strategy combinations of each party and the stability conditions of the equilibrium point in the evolutionary game system are analyzed, and the validity of the conclusions is verified through simulation results. The study shows a strong correlation between the three parties in the evolutionary game system. From the perspective of car manufacturers, the probability of producing new energy vehicles is positively proportional to the subsidy received from new energy policy, the additional revenue gained from the management of the carbon trading scheme, and the fine received for producing conventional fuel vehicles. However, from the consumer perspective, the likelihood that consumers purchase new energy vehicles is positively related to the utility value to consumers and the coverage of public charging points in the city, and inversely related to the sales price of new energy vehicles. From the government perspective, a combination of direct subsidy policies and indirect support strategies should be considered to stimulate the rapid development of the new energy vehicle industry.

Additive manufacturing (AM) offers customization of microstructure and mechanical properties of fabricated components according to the material selected, and process parameters applied. Selective laser melting (SLM) is the commonly used technique for processing high strength aluminum alloys. Selection of SLM process parameters could control the microstructure of parts and their mechanical properties. However, the process parameters limit and defects obtained inside the as-built parts present obstacles to customized part production. This study investigates the influence of SLM process parameters on the quality of as-built Al6061 and AlSi10Mg parts according to the mutual connection between the microstructure characteristics and mechanical properties. The microstructure of both materials was characterized for different parts processed over a wide range of SLM process parameters. The optimized SLM parameters were investigated to eliminate the internal microstructure defects. The behaviour of mechanical properties of parts was presented through regression models generated from the design of experiment (DOE) analysis for the results of hardness, ultimate tensile strength, and yield strength. A comparison between the results obtained and that reported in the literature is presented to illustrate the influence of process parameters, build environment, and powder characteristics on the quality of parts produced. The results obtained from this study could help to customize the part’s quality by satisfying their design requirements in addition to reducing the as-built defects which in turn reduce the amount of the post-processing needed.

To estimate the progressive collapse resistance capacity of a multi-column frame tube structure with the assembled truss beam composite floor (ATBCF), the pushdown analysis, and the nonlinear dynamic analysis as well, are conducted for such a structure by using the alternate load path (ALP) method. The bearing capacities of the remaining structures at three different work conditions, which are the side middle column failure, the edge middle column failure, and the corner column failure, are individually studied, and the collapse mechanism for the remaining structures is analyzed from the aspects of the internal force redistribution and the failure mode of the second defense line. Simultaneously, the influence of the column failure time on the dynamic response of the remaining structure and the dynamic amplification coefficient are discussed. The results show that the residual bearing capacity of the remaining structure with the bottom corner column failure is higher than that of the one with the side or edge middle column failure, while the latter has a stronger plastic deformation capacity. When the ALP method is adopted to operate the progressive collapse analysis, it is reasonable to take the column failure time as 0.1 times of the first-order vertical vibration period of the remaining structure, and it is suitable to set the dynamic amplification coefficient as of 2.0, which is the ratio of the maximum dynamic displacement to the static displacement of the remaining structure under the transient loading condition.

Background: Along with sarcopenia, delayed blood pressure (BP) recovery after standing and orthostatic hypotension (OH) are among key clinical challenges associated with ageing. Previous studies have reported an association between sarcopenia and delayed orthostatic BP recovery and OH. However, the haemodynamic mechanisms underlying this association remain unclear. Methods: 107 attendees to a falls and syncope clinic aged 50+ years underwent an active stand test with non-invasive beat-to-beat haemodynamic measurement. Hand grip strength and 5-chair stands time were measured. Muscle mass was estimated using bioelectrical impedance analysis, and participants were classified as non-sarcopenic and sarcopenic. Mixed effects models with linear splines were used to model the effect of sarcopenia status on Modelflow®-derived mean arterial pressure (MAP), cardiac output (CO), total peripheral resistance (TPR), stroke volume (SV) and heart rate (HR) after standing, while controlling for potential confounders. Results: Sarcopenia was associated with: attenuated recovery of MAP in the 10-20s period after standing (β -0.67, P<0.001); attenuated rise to peak (0-10s) and recovery from peak (10-20s) of CO (β -0.05, P<0.001; β 0.06, P<0.001); attenuated recovery (10-20s) of TPR from nadir (β -0.02, P<0.001) and attenuated recovery from peak (10-20s) of SV (β 0.54, P<0.001). HR was not significantly associated with sarcopenia status at any time interval after standing. Conclusion: The attenuated BP recovery after standing seen in sarcopenia appears to be driven by initial diminished peak of CO followed by attenuated recovery of CO from peak and TPR from nadir. The CO finding appears to be driven by SV rather than HR. Potential mechanisms for these findings include: cardio-sarcopenia, the effects of sarcopenia on the autonomic nervous system and/or the skeletal muscle pump.

In this paper, the methods and their analysis for estimating the location of three dimension (3-D) single source buried in lossy medium are presented with uniform circular array (UCA). The mathematical model of the signal in the lossy medium is proposed. Using location information in the covariance matrix obtained by sensors’ output, the equations of the source location (azimuth angle, elevation angle and range) are obtained. The phase and amplitude of the covariance matrix function are used to process these equations respectively. Then, the phase and amplitude of the covariance matrix function are used to process the source localization in the conductive medium together. By analyzing the characteristics of the proposed methods and MUSIC method, the computational complexity and the valid range of these methods are given. From the results, whether the loss is known, we can choose the appropriate method to process the issues (localization in lossless medium or lossy medium).

In order to better understand the source-sink flow and relationships of Zinc (Zn) and other nutrients in wheat (Triticum aestivum L.) plants for biofortification and improving grain nutritional quality, effects of reducing photoassimilate source (through the flag leaf removal and spike shading) or sink (through 50% spikelets removal) in the field on accumulation of Zn and other nutrients in wheat grains of two cultivars (Jimai 22 and Jimai 44) were investigated under two soil Zn application levels. The single panicle weight (SPW), kernel number per spike (KNPS), thousand kernel weight (TKW), total grain weight (TGW), concentrations and yields of various nutrient elements (Zn, Fe, Mn, Cu, N, P, K, Ca and Mg), phytate phosphorus (phytate-P), phytic acid (PA) and phytohormones (ABA: abscisic acid, and the ethylene precursor ACC: 1-aminocylopropane-1-carboxylic acid), and C/N ratios were determined. Soil Zn application significantly increased concentrations of grain Zn, N and K. Cultivars showing higher grain yields had lower grain protein and micronutrient nutritional quality. SPW, KNPS, TKW (with an exception of TKW in half spikelets removal), TGW, and nutrient yields in wheat grains were most severely reduced by half spiklets removal, secondly by spike shading, and slightly by flag leaf removal. Grain concentrations of Zn, N and Mg consistently showed negative correlations with SPW, KNPS and TGW, but positively with TKW. There were general positive correlations among grain concentrations of Zn, Fe, Mn, Cu, N and Mg, and bioavailability of Zn and Fe (estimated by molar ratios of PA/Zn, PA × Ca/Zn, PA/Fe, or PA × Ca/Fe). Although concentrations of Zn and Fe were increased and Ca was decreased in treatments of half spikelets removal and spike shading, the simultaneously increased PA limited the increase in bioavailability of Zn and Fe. In general, different nutrient elements interact with each other and are affected to different degrees by source-sink manipulations. Elevated endogenous ABA levels and ABA/ACC ratios were associated with increased TKW and grain-filling of Zn, Mn, Ca and Mg, and inhibited K in wheat grains. However, effects of ACC were diametrically opposite. These results provide basis for wheat grain biofortification to alleviate human malnutrition.

GABAA receptors are channel proteins crucial to mediating neuronal balance in the CNS. The structure of GABAA receptors allows for multiple binding sites and is key to drug development. Yet, the formation mechanism of the receptor’s distinctive pentameric structure is still unknown. This study aims to investigate the role of three predominant subunits of the human GABAA receptor in the formation of protein pentamers. Through purifying and refolding the protein fragments of the GABAA receptor α1, β2, and γ2 subunits, homopentamers were visualised with negative staining and Cryo-EM. To aid the analysis, AlphaFold2 was used to compare the structures. Results show that α1 and β2 subunit fragments successfully formed homo-oligomers, particularly homopentameric structures, while the predominant heteropentameric GABAA receptor was also replicated through the combination of the three subunits. However, it is still unclear whether γ2 subunits can form homopentamers or their main purpose is to bring together the α1 and β2 subunits to form GABAA receptors. Nevertheless, this study will lead to a deeper understanding of the atomic structure of GABAA receptors, especially in the formation mechanism of complex protein structures, and hopefully pave the way to the development of novel therapeutics for neuropsychiatric diseases.

In order to study the collapse failure of shaft wall of high depth inclined ore-pass under ore impact wear behavior, 25 ore-passes in a deep mine in Yunnan, China were investigated. Considering the ore-pass structural characteristics and the impact wear effect of ore on shaft wall, the shaft wall damage model of high depth inclined ore-pass is constructed based on the contact mechanics theory. Furthermore, No. 1#, 2#, 3# and 9# ore-passes of the mine are taken as examples for analysis, and the three results of theoretical analysis, numerical simulation and engineering case are used for comparison and verification. The shaft wall damage degree is predicted, and the damage mechanism between total shaft wall damage volume Qtol and ore-pass depth H, ore-pass dip angle θ, inclined angle of chute α, shaft diameter D and ore block size P is quantitatively investigated. The results show that the rationality of the proposed model is verified by numerical analysis and field engineering situations. Moreover, the deeper ore-pass depth H, the more shaft wall damage volume Qtol with the increase of collision frequency. Qtol increases exponentially with P and increases gradually with D. With the increase of θ or α, Qtol increases generally first and then decreases. Therefore, Qtol can be effectively reduced by selecting the appropriate structure parameters of ore-pass and adopting the technology of drilling straight ore-pass. This work provides technical support for long period safe operation of high depth inclined ore-pass.

Fusarium dry rot is one of the major postharvest potato diseases of during storage after harvest, which not only results in quality degradation but also brings up huge economic losses. The dis-ease can be elicited by some species of Fusarium, the pathogenic fungi of Fusarium causing potato dry rot are considerably diverse in various countries and regions. Fusarium spp. infection is as-sociated with dry rot produce mycotoxins, which has phytotoxicity and mycotoxicoses on hu-mans and animals. Chemical synthetic fungicide is considered as the main control measure to Fusarium dry rot of potato, nevertheless, it is unfortunate that the persistent application inevitably results in the emergency of resistant strain and environmental contamination. A comprehensive disease control strategy includes potato cultivar selection, appropriate cultural practices (crop rotation, cultivate pattern, fertilization, and irrigation), harvesting process and postharvest treatment (harvesting, classification, packaging, wound healing), storage condition (environ-mental disinfection, temperature, humidity and gas composition) along with the application of fungicide pre-harvest or postharvest. Recently, emerging studies indicated that eco-friendly strategies include physical control, chemical methods (such as the application of generally rec-ognized as safe (GRAS) compounds or chemical (elicitors) and biological control have been in-troduced to combat Fusarium dry rot of potato.

With the recent developments in augmented reality (AR) technologies comes an increased interest in the use of smart glasses for hands-on training. Whether this interest is turned into market success or not depends at the least on whether the interaction with smart AR glasses satisfies users, an aspect of AR use that so far has received little attention. With this contribution, we seek to change this. The objective of the article, therefore, is to investigate user satisfaction in AR applied to three cases of practical use. User satisfaction of AR can be broken down into satisfaction with the interaction and satisfaction with the delivery device. A total of 142 participants from three different industrial sectors contributed to this study, namely, aeronautics, medicine, and astronautics. In our analysis, we investigated the influence of different factors, such as age, gender, level of education, level of Internet knowledge, and the roles of the participants in the different sectors. Even though users were not familiar with the smart glasses, results show that general computer knowledge has a positive effect on user satisfaction. Further analysis using two-factor interactions shows that there is no significant interaction between the different factors and user satisfaction. The results of the study affirm that the questionnaires developed for user satisfaction of smart glasses and the AR application performed well, but leave room for improvement.

Buckling defect will appear on the outer surface of the deformed ring during constrained ring rolling (CRR) of aluminum alloy thin wall conical ring with inner high ribs (AATWCRIHR), if the geometrical dimension of the ribs doesn't match the wall thickness. To avoid the buckling defect, a quantitative method for characterizing the degree of the buckling defect is proposed using the area of buckling profile. Then an orthogonal experimental scheme was designed taking the width of the middle rib, thickness of wall, and height of the middle rib as design variables and defining the area of buckling profile as optimization objective. Subsequently, a quadratic polynomial response surface model was established by combining the optimization algorithm with the finite element method (FEM), and the geometrical dimension of the middle ribs of the deformed AATWCRIHR is optimized. Also the optimal parameter combination to minimize the area of buckling profile is obtained and verified using FE simulation. Results show that the AATWCRIHR after optimization doesn’t generate the buckling defect during constrained ring rolling, and it is proved that the quantitative buckling defect representation method and the optimization design method based on the response surface model and the finite element simulation results are feasible for the constrained ring rolling process of the AATWCRIHR.

In the fifth generation communication system, millimeter wave (mmWave) networks will coexist with traditional micro wave (μWave) networks, which allows for higher data transmission rate and better user experience. In this paper, we give a comprehensive framework of mathematical models and analytical methods for multi-tier mmWave and μWave hybrid caching networks based on stochastic geometry. We propose an association strategy by assuming average biased-received power association and Rayleigh fading. Accordingly, by using a D-ball approximating blockage model of mmWave networks, expressions of the cell association probability and the coverage probability of the hybrid networks are derived. Also, we use the average successful delivery probability as the performance metric to analyze the existing caching placement strategies. Simulation results validate the accuracy of our analytical conclusions.

The prediction of stock prices holds significant implications for researchers and investors in evaluating stock value and risk. In recent years, researchers have increasingly replaced traditional machine learning methods with deep learning approaches in this domain. However, the application of deep learning in forecasting stock prices is confronted with the challenge of overfitting. To address the issue of overfitting and enhance predictive accuracy, this study proposes a stock prediction model based on GRU (Gated Recurrent Unit) with reconstructed datasets. This model integrates data from other stocks within the same industry, thereby enriching the extracted features and mitigating the risk of overfitting. Additionally, an auxiliary module is employed to augment the volume of data through dataset reconstruction, thereby enhancing the model’s training comprehensiveness and generalization capabilities. Experimental results demonstrate a substantial improvement in prediction accuracy across various industries.

In the world city theory, most researchers focus on the service sector in the urban economy and less discuss the role of manufacturing. However, the path of only emphasizing financial and corporate service could not fit the sustainability concept. Compared to Anglo-American world city, Global South’s world cities have distinct pathway to be industrialization, tertiarization and globalization. This paper adopted dynamic historic perspective with first-hand materials including in-depth interviews with managers and government officers and second-hand data including yearbook statics and economic census to closely examine the emerging world city-- ‘World Factory’ in Global South, Guangzhou in China, from 1949 to 2015, to emphasize how manufacturing affects the urban globalization through three dimensions, economic, social and spatial dimensions. To make the confirmation of the role of manufacturing in Guangzhou as sustainable world city, we find manufacturing in Guangzhou builds up the basic foundation of export-oriented economy and makes positive effects on urban economic transformation. In addition, manufacturing remains important source of employment and foreign immigration. Along with urbanization and industrialization, urban spatial expansion and aggregation changes with different urban development concept. We provide new insights on multiple globalization on manufacturing for sustainable world city.

Euler sums are alternating (or level two) extension of multiple zeta values (MZVs). Kaneko and Tsumura initiated the study of multiple T-values (MTVs), another level two generalization, by restricting the summation indices in the definition of MZVs to a fixed parity pattern. In this paper, we shall study finite MTVs and their alternating versions which are level two and level four variations of finite MZVs, respectively. We conjecture that all finite MZVs are in the Q-span of finite MTVs which in turn apparently lie in the span of finite Euler sums, and the inclusions are both proper. We shall first provide some structural results for Euler sums of small weights, guided by the author's previous conjecture that the finite Euler sum space of weight w is isomorphic to a quotient Euler sum space of weight w. Then, by utilizing some well-known properties of the classical alternating MTVs, we shall derive a few important Q-linear relations among the finite alternating MTVs, including the reversal, linear shuffle and sum relations. We then compute the upper bound for the dimension of the Q-span of weight w finite (alternating) MTVs for w<9, both rigorously using the newly discovered relations and numerically aided by computers.

Spacecraft recovery technology is crucial in the field of aerospace, in which the parachute plays a key role in slowing down the descent speed of the spacecraft and realizing a smooth landing. In order to construct a dynamically adjustable parachute deployment strategy, it is necessary to measure the parachute dynamic load accurately in real time. However, the existing sensor measurement scheme is difficult to meet the measurement requirements due to its large structure and complex wiring. In order to meet the current demand for real-time measurement of parachute cords dynamic load, a miniature measuring instrument is designed.According to the function and technical requirements of the miniature measuring instrument, the hardware modules of the acquisition system are selected and designed, and the integration debugging and performance optimization of the microcontroller module, A/D sampling module, signal acquisition circuit and power supply module are carried out. The software of the parachute cords tension acquisition system based on the miniature measuring instrument is developed. The elastomer is modeled by using SolidWorks and statically analyzed by using AnsysWorkbench finite element analysis software. Then the final structure of the elastomer and the pasting position of the strain gage are determined through the results analysis as well as experimental verification. The hardware module of the signal acquisition system for the miniature measuring instrument is then encapsulated. The force value of the miniature measuring instrument is calibrated and tested many times by using the microcomputer-controlled electronic universal testing machine. The experimental results show that the designed miniature measuring instrument has accurate data, strong stability and good real-time performance, which meets the demand for real-time accurate measurement of miniature measuring instrument, and can provide reliable data for parachute cords parameter validation and stepless unfolding design.

This study investigates the impact of specimen size on the mechanical properties of wood, specifically focusing on compression strength, elastic modulus, and Poisson's ratio. Compression tests were conducted using three different specimen sizes (20mm×20mm×30mm, 40mm×40mm×60mm, 60mm×90mm×90mm) in the longitudinal, radial, and tangential directions. Mechanical parameters, failure mechanisms, load-displacement curves, and stress-strain relationships were systematically analyzed for each size. The study also evaluated the influence of specimen size on the accuracy of finite element numerical simulations by utilizing the obtained mechanical parameters. The results reveal a significant correlation between compressive strength and specimen size, indicating a decrease in compressive strength with increasing specimen size. Conversely, elastic modulus and Poisson's ratio exhibit less sensitivity to variations in specimen size. Notably, parameters derived from small-sized specimens (20mm×20mm×30mm) exhibited substantial errors, while those obtained from medium-sized (40mm×40mm×60mm) and large-sized specimens (60mm×90mm×90mm) demonstrated greater reliability, providing precise results in finite element numerical simulations.

Classifying network flow subsequences in an Industrial IoT gateway is an effective method for identifying Industrial IoT faults. This paper proposes a subsequence classification algorithm SSGBUL-IKNN based on unsupervised learning encoding to address the problem of low classification accuracy. Firstly, we built a network module based on unsupervised learning to encode the flow sequence of the Industrial IoT gateway. In the encoding module, a subsequence calibration algorithm controls the increasing error during the coding process. Then, the specific fault type is obtained through an improved KNN classification algorithm based on the indication distance source from the integrated coding sequences converted by multi-dimensional network flow sequences. The test result on three Industrial IoT datasets of a sewage treatment plant shows that the accuracy of SSGBUL-IKNN in this paper exceeds 92%, significantly higher than the algorithm DTW and TSF. It reaches the classification requirements of Industrial IoT fault diagnosis.

Numerous dynamic and complicated processes characterize development from the oocyte to the embryo. However, given the importance of functional transcriptome profiles, long non-coding RNAs, single-nucleotide polymorphisms, and alternative splicing during embryonic development, the effect that these features have on the blastomeres of 2-, 4-, 8-, 16-cell, and morula stages of development have not been studied. Here, we conducted a scRNA-seq survey of cells from sheep from the oocyte to the blastocyst developmental stages. We then carried out experiments to identify and functionally analyze the transcriptome profiles, long non-coding RNAs, single-nucleotide polymorphisms (SNPs), and alternative splicing (AS). We founded that between the oocyte and zygote groups significantly down-regulated genes and the second-largest change in gene expression occurred between the 8- and 16-cell stages. We used various methods to construct a profile to characterize cellular and molecular features and systematically analyze the related GO and KEGG profile of cells of all stages from the oocyte to the blastocyst. This large-scale, single-cell atlas provides key cellular information and will likely assist clinical studies in improving preimplantation genetic diagnosis.

Kombucha is a popular sparkling sugared tea, fermented by a symbiotic culture of acetic acid bacteria (AAB) and yeast. The demand for Kombucha is increasing worldwide mainly due to its perceived health benefits and appealing sensory properties. This study isolated and characterised the dominant AAB and yeast from starter culture and Kombucha broth after 0, 1, 3, 5, 7, 9, 11, and 14 days of fermentation at ambient temperature (~22°C). Changes in the microbial composition were associated with variations in the physico-chemical characteristics of Kombucha tea, such as pH, titratable acidity, and total soluble solids (TSS). During fermentation, the acidity increased, and TSS decreased. The yield, moisture content and water activity of the cellulosic pellicles which had developed by the end of fermentation were attributed to the presence of AAB. Yeast and AAB were isolated from the Kombucha samples using glucose yeast extract mannitol ethanol acetic acid (GYMEA) and yeast extract glucose chloramphenicol (YGC) media respectively, using serial dilutions. Phenotypic and taxonomic identification of AAB and yeast were determined by morphological and biochemical characterisation, followed by sequence analysis of the ribosomal RNA gene (16S rRNA for AAB and ITS for yeast). The dominant AAB species in the cellulosic pellicle and Kombucha broth was identified as Komagataeibacter rhaeticus. The yeast isolates belonged to Debaryomyces prosopidis and Zygosaccharomyces lentus.

Additive manufacturing (AM) provides customization of the microstructure and mechanical properties of components. Selective laser melting (SLM) is the commonly used technique for processing high strength Aluminum alloys. Selection of SLM process parameters could control the microstructure of fabricated parts and their mechanical properties. However, process parameter limits and defects inside the as-built parts present obstacles to customized part production. This study is the second part of a comprehensive work that investigates the influence of SLM process parameters on the quality of as-built Al6061 and AlSi10Mg parts. The microstructure of both materials was characterized for different parts processed over a wide range of SLM process parameters. The optimized SLM parameters were investigated to eliminate the internal microstructure defects. Mechanical properties of the parts were illustrated by regression models generated with design of experiment (DOE) analysis. The results reported in this study were compared to previous studies, illustrating how the process parameters and powder characteristics could affect the quality of produced parts.