The combination of neural network and beamforming has been proved to be very effective in multi-channel speech separation. But its performance faces a challenge in complex environment. In this paper, an iteratively refined multi-channel speech separation method is proposed for the challenge, where the proposed is composed of initial separation and iterative separation. In initial separation, the time-frequency domain dual-path recurrent neural network neural network (TFDPRNN), minimum variance distortionless response (MVDR) beamformer and post-separation (also TFDPRNN) are cascaded for obtaining the first additional input in iterative separation. In iterative separation, the MVDR beamformer and post-separation are iteratively used, where the output of the MVDR beamformer is used as an additional input of the post-separation network and the final output comes from post-separation module. This iteration of the beamformer and post-separation is fully employed for promoting their individual optimization, which ultimately improves the overall performance of speech separation in multi-speaker scenarios. Experiments on the spatialized version of the WSJ0-2mix corpus show that our proposed method is significantly better than the current popular methods. In addition, the method also has a good effect on the dereverberation task.

The use of salt rock for underground radioactive waste disposal facilities requires a comprehensive analysis of creep-damage process in salt rock. A computer-controlled creep setup is employed to carry out a creep test of salt rock lasted as long as 359 days under a constant uniaxial stress. The AE space-time evolution and energy releasing characteristics during creep test are studied in the meantime. A new creep-damage model is proposed on the basis of fractional derivative by combining the AE statistical regularity. It indicates that the AE data in non-decay creep process of salt rock can be divided into three stages. Furthermore, the parameters of new creep-damage model are determined by Quasi-Newton method. The fitting analysis suggests that the creep-damage model based on fractional derivative in this paper provides a precise description of full creep regions in salt rock.

Three new compounds (1, 11 and 12), together with 32 known ones, were isolated from the root bark of Morus alba L. using various chromatographic methods. The structures of the undescribed compounds were elucidated based on 1D, 2D NMR and HRESIMS data analysis, while the known ones were identified by comparison of their spectroscopic data with those reported in the literature. All the isolates were evaluated for their cytotoxic activities against human gastric cancer HGC27 cells by CCK-8 assay. Among them, compounds 5, 8, 10 and 30 exhibited cytotoxic activities on HGC27 cells with IC50 values of 10.24 ± 0.89 μM, 28.94 ± 0.72 μM, 6.08 ± 0.34 μM and 33.76 ± 2.64 μM, respectively. Furthermore, compound 10 was confirmed to reduce proliferation ability, increase apoptosis rate and inhibit cell migration pathway by annexin V/PI double staining experiment, transwell experiment and western blot analysis.

Different inlet structures have a significant impact on the internal flow characteristics of a solid-magnesium powder water ramjet engine. Based on the magnesium-water reaction model, a computational fluid dynamics (CFD) method is applied to establish a numerical simulation method for the internal flow field of the engine, and the internal flow characteristics of the engine under different inlet structure conditions are studied. The simulation results show that high-temperature gas can effectively promote the ignition of magnesium powder at the top of the combustion chamber, while accelerating the evaporation of the first inlet water and increasing the combustion rate of magnesium powder. The secondary inlet has the most significant effect on the temperature inside the combustion chamber. When the secondary inlet flow rate increases towards the top of the combustion chamber, it increases the amount of heat absorbed by the evaporating water at the top of the chamber, thereby reducing the temperature at the top of the combustion chamber. However, when the flow rate is low, it results in insufficient oxidizer at the top of the combustion chamber, which is unfavorable for the combustion of magnesium powder.

Current numerical methods for simulating biophysical processes in aquatic environments are typically constructed in a grid-based Eulerian framework or as an individual-based model in a particle-based Lagrangian framework. Often, the biogeochemical processes and physical (hydrodynamic) processes occur at different time and space scales, and changes in biological processes do not affect the hydrodynamic conditions. Therefore, it is possible to develop an alternative strategy to grid-based approaches for linking hydrodynamic and biogeochemical models that can significantly improve computational efficiency for this type of linked biophysical model. In this work, we utilize a new technique which links hydrodynamic effects and biological processes through a property-carrying particle model (PCPM) in a Lagrangian/Eulerian framework. The model is tested in idealized cases and its utility is demonstrated in a practical application to Sandusky Bay. Results show the integration of Lagrangian and Eulerian approaches allows for a natural coupling of mass transport (represented by particle movements and random walk) and biological processes in water columns which is described by a nutrient-phytoplankton-zooplankton-detritus (NPZD) biological model. This method is far more efficient than traditional tracer based Eulerian biophysical models for 3-D simulation, particularly for a large domain and/or ensemble simulations.

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

The control of alumina morphology is crucial yet challenging for its various applications. Un-fortunately, traditional methods for preparing alumina particles suffer from several limitations such as irregular morphology, poor dispersibility, and restricted application areas. In this study, we develop a novel method for preparing spherical mesoporous alumina using chitin and Plu-ronic P123 as mixed templates. The effects of reaction temperature, time, and the addition of mixed templates on the phase structure, micromorphology, and optical absorption properties of the samples were investigated. The experimental results indicate that lower temperature and shorter reaction time facilitated the formation of spherical mesoporous alumina with excellent CO2 adsorption capacity. The periodic density functional theory (DFT) calculations demonstrate that both (110) and (100) surfaces of γ-Al2O3 can strongly adsorb CO2. The difference in the amount of CO2 adsorbed by Al2O3 is mainly due to the different surface areas, which give dif-ferent number of exposed active sites. This approach introduces a novel strategy for utilizing bi-ological compounds to synthesize spherical alumina and greatly enhances mesoporous alu-mina's application efficiency in adsorption fields. Moreover, the study explored the electro-chemical performance of the synthesized product using cyclic voltammetry and discovered im-proved loading of electrocatalysts and enhanced electrocatalytic activity.

Tungsten and its alloys are considered as a key component in high temperature environment. Self-passivating W-Si-xY alloys with different Y contents made from the powders milled for different times were prepared by mechanical alloying (MA) and spark plasma sintering (SPS). Their microstructures and oxidation resistance were investigated. It is found that the oxidation resistance of the alloys with low Y contents (0Y and 2Y) made from 20 h-milled powders is worse than that of the alloys made from 4 h-milled powders. It is because the protective WO3/SiO2 composite layer is discontinuous. While the alloys with high Y contents (4Y and 6Y) made from 4 h and 20 h-milled powders show good oxidation resistance. Even, the thickness of the oxide layer of the alloys with 4Y and 6Y made from 20 h-milled powders after oxidation at 1000 ℃ for 2 h is 84.0 μm and 70.7 μm, less than that made from 4 h-milled powders. This is due to the size and distribution of W5Si3, Y2Si2O7 aggregates and W-Y-O melt. The synergistic effects of Y contents and milling time on the microstructures and oxidation resistance of the alloys are revealed.

In this paper, MgAl Layered double hydroxides (LDH) were synthesized by co-precipitation method using a colloid mill and characterized by XRD, IR and SEM. The LDHs was repeatedly tested and compared with different bearing lifetime tester in lithium base grease, and it was found that the environmental-friendly LDHs had greater performance than the traditional antioxidant, and it was the development direction of a new generation of environmental-friendly antioxidants in the future. By adding LDHs into large electric shovel greats (GRK-A) in open-pit coal mine, it can be seen by PDSC evaluation that the service lifetime of grease is extended by 20% while the overall performance of grease is not affected. With the increase of LDHs addition, the grease sample gets the greater activation energy, the stronger thermal oxidation and decomposition resistance. Comparing the energy storage modulus and flow transition index at different temperatures, it can be seen that adding the right amount of LDHs needs close attention for the system oxidation resistance and viscoelasticity. For the electric shovel grease system, the best oxidation resistance and rheological properties can be achieved by adding 2% of LDHs. The rheological viscosity-temperature curves show that the grease samples with different ratios of solid LDHs have better low-temperature properties than the mine grease.

The external and internal structures of male and female adults of Culicoides grisescens Edwards, were examined with scanning electron microscope (SEM) and tissue section techniques. Specimens were collected from Qilian Mountain National Park in Qinghai Province, China. The ultrastructure and morphology of compound eyes, antenna, maxillary palpus, spermathecae, genitalia and other structural characteristics of both male and female adults of C. grisescens are described. Internal structures of the species are described, including histological sections of the digestive, nervous, respiratory, and reproductive systems. This paper provides visual and descriptive details for the systematic taxonomic study of Ceratopogonidae.

Sialylated milk oligosaccharides (SMOs) is the most important oligosaccharides in human milk oligosaccharides (HMOs), and have a multifunctional health benefit, and the most abundant SMOs are sialyllactose (SLs). The previous studies indicate that the growth of tumor cells, and angiogenesis on tumor tissues with Lewis lung carcinoma, melanoma, and colon carcinoma cells could be prevented by SL. Thus, it has been proposed that SL might be an ideal candidate for the development of anti-angiogenic drugs without any side effects. It has been proposed that the Sialic acid (Sia) can be produced through SL’s hydrolysis, and the dietary Sia is further transported to the brain and other tissues though blood for formation of CMP-Sia, the activated precursor of Sia, and then is catalyzed by polysialyltransferases (polySTs) for synthesis of polysialic acid (polySia) or polysialylation of neural cell adhesion molecule (NCAM). Thus, it’s necessary to study and develop new inhibitors, which not only modulate a proper balance between the gut health and neuros system development, but also inhibit the overexpression of polySia, and thus block the tumor cell migration. In this study, we proposed that 3’-SL and 6’-SL may be more ideal inhibitors comparing with two previous inhibitors, the low molecular weight heparin (LMWH) and cytidine monophosphate (CMP) in the previous studies.

Background Acute kidney injury (AKI) is a common comorbidity in the intensive care unit (ICU), with higher mortality rate among those who receive continuous renal replacement therapy (CRRT). This study aimed to investigate the association of white blood cell (WBC) levels with all-cause mortality in AKI patients undergoing CRRT. Method We conducted a post hoc analysis of ICU patient data from multiple centers in Korea. First, the levels of WBCs were classified into four groups based on quartiles. Second, the relationship between different WBC levels and mortality was investigated with the Kaplan-Meier (K-M) survival curves, Cox proportional hazards model, and generalized additivity model (GAM). Finally, we used multiple imputation to avoid bias caused by non-randomized missing data. The endpoints were short-term (28 days) and long-term (90 days) mortality. Result In our analysis, a total of 1,100 ICU patients were included. Among them, 670 (60.90%) and 781 (71.00%) died within 28 and 90 days, respectively. K-M survival curves showed that patients with the lowest WBC levels had the highest risk of mortality for both outcomes. Adjusted multivariate Cox regression analysis confirmed that compared with the reference level (quartile 2), low WBC levels increased the risk of both 28-day mortality (quartile 1, HR = 1.43, 95% CI: 1.13–1.83, P = 0.004) and 90-day mortality (quartile 1: HR = 1.32; 95% CI: 1.05-1.66, P = 0.016). GAM analysis showed a non-linear, U-shaped relationship between pre-CRRT WBC levels and all-cause mortality (non-linear P < 0.05). Conclusion The baseline WBC level is an independent predictor of prognosis for ICU patients receiving CRRT. Patients in the lowest WBC quartile had the highest risk of all-cause mortality. These results provide further evidence that early observation and intervention may have a prognostic value for these high-risk patients.

In view of the limitations of the existing eccentricity error separation method of the rotary table, an eccentricity error separation method based on the phase feature of the moiré signal of single reading head is proposed herein. A grating pair transmission model is established based on the analysis of the principle of the rotary table, thereby the influence of eccentricity error on the phase feature of the moiré signal in the rotation course of the rotary table is clarified, and the corresponding model between the phase feature spectral components and the eccentricity error is established. The verification experiments of the proposed method are carried out based on the laboratory-made circuit system. After verifying the accuracy of the data acquisition of the laboratory-made circuit board, the verification experiments of the eccentricity error separation effect of the proposed method are carried out. The experimental data are compared with those of the traditional method and the results show that the error between the two methods is 2.34μm and the relative error is 2.3%.

The process of shock wave focusing can make the strength of shock waves be continuously accumulated and turned into detonation wave in Pulse Detonation Engine (PDE). However, its effective application needs the inlet jets be in high temperature and velocity, which is difficult to be satisfied under certain conditions. Therefore, in this paper, metal magnesium assisted detonation initiation is proposed and the effect of magnesium particle addition on the shock wave focusing process in a kerosene-fueled PDE with cavity configuration is investigated through numerical simulation. The result showed that when the temperature of the premixed fuel/air jets injected in opposite direction was set as 650 K, the collision of leading shock waves on the central axis was the main source of energy deposition and the shock wave focusing could make the detonation be initiated in the cavity. When the temperature of jets is reduced to 550 K, fuel ignition and detonation could not be achieved through shock wave focusing. Then adding metal magnesium particles into the combustor made the energy deposition be enhanced and the detonation be induced. The diffusion of metal particles can significantly change the structure, motion, merging and dissipation of vortices in the flow field. Generally, the shock wave focusing process is basically not affected with metal particles injection. Therefore, this method can be successfully employed for detonation initiation in the cavity when the fuel/air premixed jet temperature is not high for PDE.

Viruses can induce the fusion of infected and neighboring cells, leading to the formation of syncytia. Cell-cell fusion is mediated by viral fusion proteins on the plasma membrane of infected cells that interact with cellular receptors on neighboring cells. Viruses use this mechanism to spread rapidly to adjacent cells or escape host immunity. For some viruses, syncytium formation is a hallmark of infection and a known pathogenicity factor. For others, the role of syncytium formation in viral dissemination and pathogenicity remains poorly understood. Human cytomegalovirus (HCMV) is an important cause of morbidity and mortality in transplant patients and the leading cause of congenital infections. Clinical HCMV isolates have broad cell tropism but differ in their ability to induce cell-cell fusions, and little is known about the molecular determinants. We developed a system to analyze HCMV glycoprotein B (gB) variants in a defined genetic background. HCMV strains TB40/E and TR were used as vectors to compare the fusogenicity of six gB variants from congenitally infected fetuses with those from three laboratory strains. Five of them conferred the ability to induce fusion of MRC-5 human embryonic lung fibroblasts to one or both backbone strains, as determined by a split GFP-luciferase reporter system. The same gB variants were not sufficient to induce syncytia in infected ARPE-19 epithelial cells, suggesting that additional factors are involved. The system described here allows a systematic comparison of the fusogenicity of viral envelope glycoproteins and may help to clarify whether fusion-promoting variants are associated with increased pathogenicity.

During public health events, Active Mobility (walking and cycling) plays an important role in securing residents' travel. To enhance the resilience of urban transportation, this article integrates the travel environment elements for walking and cycling and constructs a travel environment for Active Mobility evaluation index system. This article uses survey data from the main urban area of Harbin in the context of the COVID-19 pandemic in May 2022, and combines the Gradient Boosting Decision Tree (GBDT) and Impact-Asymmetry Analysis (IAA) methods to analyze the satisfaction of the travel environment for Active Mobility. It proposes strategies for optimizing the travel environment for Active Mobility, ensuring residents' travel during public health events, guiding them to adopt Active Mobility, and improving urban transportation resilience. This research shows that Active Mobility can enhance urban transportation resilience. In addition, there are differences in resident demand for walking and cycling environments in the travel environment for Active Mobility. Residents are more concerned about the comfort of the walking environment, while they prioritize the convenience of the cycling environment.

Establishing an accurate mathematical model is the foundation of simulating the motion of marine vehicles and structures, and it is the basis of modeling-based control design. System identification from observed input-output data is a practical and powerful method. However, for modeling objects with different characteristics and known information, a single modeling framework can hardly meet the requirements of model establishment. Moreover, there are some challenges in system identification, such as parameter drift and overfitting. In this work, three robust methods are proposed for generating ocean hydrodynamic models based on Bayesian regression. Two Bayesian techniques, semi-conjugate linear regression and noisy input Gaussian process regression, are used for parametric and nonparametric gray-box modeling and black-box modeling. The experimental free-running tests of the KVLCC2 ship model and a multi-freedom wave energy converter (WEC) are used to validate the proposed Bayesian models. The results demonstrate that the proposed schemes for system identification of the ship and WEC have good generalization ability and robustness. Finally, the developed modeling methods are evaluated considering the aspects required conditions, operating characteristics and prediction accuracy.

L-Theanine, a unique non-protein amino acid, is an important bioactive component of green tea. Previous studies have shown that L-theanine has many potent health benefits, such as anti-anxiety effect, regulation of immune response, relaxing neural tension, reducing oxidative damage. However, little is known concerning whether L-theanine can improve the clearance of mitochondrial DNA (mtDNA) damage in organisms. Here, we reported that L-theanine treatment increased ATP production and improved mitochondrial morphology to extend the lifespan of UVC-exposed nematodes. Mechanistic investigations showed that L-theanine treatment enhanced the removal of mtDNA damage and extended lifespan by activating autophagy, mitophagy, mitochondrial dynamics, and mitochondrial unfolded protein response (UPRmt) in UVC-exposed nematodes. In addition, L-theanine treatment also up-regulated the expression of genes related to mitochondrial energy metabolism in UVC-exposed nematodes. Our study provided a theoretical basis for the possibility that tea drinking may prevent mitochondrial related diseases.

Salidroside, a valuable phenylethanoid glycoside, is obtained from plants belonging to the Rhodiola genus, known for its diverse biological properties. At present, salidroside is still far from large-scale industrial production due to the lower titer and higher process cost. In this study, we constructed a biosynthetic pathway from L-tyrosine to salidroside in Saccharomyces cerevisiae. To increase sali-droside production, we for the first time constructed an in vivo UDP-glucose regeneration system that sucrose synthase GmSUS worked in conjunction with UDP-glucose transferase RrUGT33 to improve the UDP-glucose availability with inexpensive sucrose as the consumed substrate. Finally, the molar conversion rate of L-tyrosine could reach 95%. To further reduce the cost, co-culture with E. coli that synthesized L-tyrosine de novo resulted in an 81% reduction in the final substrate cost per 1 kg of salidroside compared to the initial cost. The final titer of salidroside obtained 3.8 g/L and was the highest titer achieved at the Shake-Flask-Level in the existing reports. And this marked the first successful synthesis of salidroside in an in situ enhanced UDP-glucose system using sucrose. This accomplishment laid a robust groundwork for further investigations into the synthesis of other notable glycosides and natural compounds.

The iridoids of H. diffusa play an important role in the anti-inflammatory process, but the specific iridoid with anti-inflammatory effect and its mechanism is lack of study. An iridoid compound named scandoside (SCA) was isolated from H. diffusa and its anti-inflammatory effect was investigated in lipopolysaccharide (LPS)-induced RAW 264.7 cells. Its anti-inflammatory mechanism was confirmed by in intro experiment and molecular docking analysis. As results, SCA significantly decreased the productions of nitric oxide (NO), prostaglandin E₂ (PGE₂), tumor necrosis factor-α (TNF-α) and interleukin-6 (IL-6) and inhibited the levels of inducible nitric oxide synthase (iNOS), cyclooxygenase-2 (COX-2), TNF-α and IL-6 mRNA expression in LPS-induced RAW 264.7 cells. SCA treatment suppressed the phosphorylation of inhibitor of nuclear transcription factor kappa-B alpaha (IκB-α), p38, extracellular signal-regulated kinase (ERK) and c-Jun N-terminal kinase (JNK). The docking data suggested that SCA had great binding abilities to COX-2, iNOS and IκB. Taken together, the results indicated that the anti-inflammatory effect of SCA is due to inhibition of pro-inflammatory cytokines and mediators via suppressing the nuclear transcription factor kappa-B (NF-κB) and mitogen-activated protein kinase (MAPK) signaling pathways, which provided useful information for its application and development.

In this paper, under the symmetric entropy and the scale squared error loss functions, we consider the maximum likelihood (ML) estimation and Bayesian estimation of the Shannon entropy and Rényi entropy of the two-parameter inverse Weibull distribution. In the ML estimation, the dichotomy is used to solve likelihood equation. In addition, the approximation confidence interval is given by the Delta method. Because the form of estimation results is more complex in the Bayesian estimation, the Lindley approximation method is used to achieve the numerical calculation. Finally, Monte Carlo simulations and a real data set are used to illustrate the results derived. By comparing the mean square error between the estimated value and the real value, it can be found that the performance of ML estimation of Shannon entropy is better than that of Bayesian estimation, and there is no significant difference between the performance of ML estimation of Rényi entropy and that of Bayesian estimation.

This paper studies the maximum reliability of multi-hop relay UAV, in which UAV provides wireless services for remote users without direct communication link on the ground as a coded cooperative relay. In this paper, the analytical expressions of total power loss and total bit error rate are derived as reliability measures. Firstly, based on the environmental statistical parameters, a LOS probability model is proposed. Then the problem of minimizing the bit error rate of static and mobile UAVs is studied. The goal is to minimize the total bit error rate by jointly optimizing the height, elevation, power and path loss, and subject to the maximum allowable path loss con-straints, transmission power allocation constraints and UAV height and elevation constraints. At the same time the total path loss is minimized to achieve maximum ground communication cov-erage. However, the formulated joint optimization problem is non-convex and generally difficult to solve. Therefore, we decomposed the problem into two subproblems and proposed an effective joint optimization iteration algorithm. Finally, the simulation results are given, and the analysis shows that the optimal height of different reliability measures is slightly different, and using the mobility of UAVs can improve the reliability of communication performance.

A practical method is presented to estimate rare earth elements (REE) concentrations in magmatic vapour phase (MVP) in equilibrium with water-saturated granitic melts based on empirical fluid-melt partition coefficients of REE (k_P^REE). The values of k_P^REEcan be calculated from a set of new polynomial equations linking to the chlorine molality (m_Cl^v) of the MVP associated with granitic melts, which are established via a statistical analysis on the existing experimental dataset. These equations may be applied to the entire pressure range (0.1 to 10.0 kb) within the continental crust, suggesting that light REEs behave differently in magmatic fluids, i.e. either being fluid compatible with higher m_Cl^v or fluid incompatible with lower m_Cl^v values. In contrast, heavy REEs are exclusively fluid incompatible and partition favourably into granitic melts. Consequently, magmatic fluids tend to be rich in LREE relative to HREE, leading to REE fractionation during the evolution of magmatic hydrothermal systems. Maximum k_P^REEvalue for each element is predicted and presented in a REE distribution diagram constrained by the threshold of m_Cl^v. REE contents of the granitic melt is approximated by whole-rock analysis, so that REE concentrations in the associated MVP would be estimated from the value of k_P^REE given chemical equilibrium retains. Two examples are provided respectively, to show the use of this method as a REE tracer to fingerprint the source of ore-fluids responsible for the Lake George intrusion-related Au-Sb deposit in New Brunswick (Canada), and for the Bakircay Cu-Au (-Mo) porphyry systems in northern Turkey.

Using graph theory, computer aided motion, static force and power flow analysis of planetary gear mechanism is realized. The motion, static force and efficiency calculations of 6HP26 automatic transmission are carried out. Based on kinematic and static force analysis model, related matrices are acquired. Hence, kinematic and static force analysis of planetary gear mechanism is achieved. The link power can be determined by the link speed and torque. Power flow diagrams of each gear are acquired. The efficiency is calculated by transmission ratio method.

Yaw misalignment can make a wake steer, which is an effective method to increase the power of wind farms, but it also increases the fatigue load of the turbines. In this paper, the method of combining yaw misalignment and pitch control (CYMP) is proposed to investigate the potential to mitigate wake interference, the wind velocity distribution and turbulence distribution in the wake, as well as the power and load changes of the wind turbine are studied, focusing on power in-crement and fatigue damage reduction. Although some studies have found that the method of CYMP are beneficial to increase power generation and reduce fatigue loads, there are no papers that have made a detailed analysis of the effects of wake turbulence, wind speed distribution, power, especially fatigue damage under this control. Simulation tool FAST.Farm is used to model and analyze wind farms, obtain the variation details of wake and provide simulation data for calculating power and fatigue load. The pitch control brings bias to the CYMP optimization results was neglected, the case studies show that the method of CYMP can reduce the fatigue load by 10.29% and increase the total power by 1.7% compared with only wake steering. The Model Predictive Control collaborative method based on CYMP is proposed, which can increase power by more than 2% and reduce thrust by more than 4% under 10m/s turbulent wind.

Four previously undescribed highly oxygenated diterpenoids (1–4), zeylleucapenoids A–D, characterized by halimane and labdane skeletons, were isolated from the aerial parts of Leucas zeylanica. Their structures were elucidated primarily by NMR experiments. The absolute configuration of 1 was established by theoretical ECD calculations and X-ray crystallographic analysis, whereas those for 2−4 were assigned by theoretical ORD calculations. Zeylleucapenoid D (4), with an IC₅₀ value of 38.45 μM in RAW264.7 macrophages and nontoxic activity for zebrafish embryo, and obviously inhibited pro-inflammatory cytokines TNF-α and IL-6 in a dose-dependent manner. Compound 4 inhibited of the expression of inducible nitric oxide synthase (iNOS) and cyclooxygenase-2 (COX-2). Furthermore, molecular docking analysis indicated the possible mechanism of action for 4 may be bind to targets by hydrogen- and hydrophobic- bond interactions.

ESG (Environmental, Social, and Governance) responsibility fulfillment increasingly affects enterprise valuation. Although researchers debate about the precise effects, the prevailing view suggests a linear relationship between ESG performance and enterprise value. This study introduces a novel ESG responsibility performance metric through the Regulated Intermediary Model to delve into this relationship within the Chinese context. Our findings reveal an inverted U-shaped relationship between ESG performance and enterprise value, with financing constraints having a significant moderating effect. These findings remain robust after employing instrumental variables to mitigate potential endogeneity. Heterogeneity analysis demonstrates that this inverted U-shaped relationship is particularly pronounced in non-polluting and non-state-owned enterprises. Moreover, a comparison between equity and debt financing mechanisms underscores that improved ESG performance is associated with lower cost of equity financing, thereby enhancing enterprise value. Financial institutions are encouraged to leverage innovative financial instruments to diversify enterprise financing channels and alleviate financing constraints of enterprises that fulfill their ESG responsibilities.

A variety of myricetin derivatives bearing ferulic acid amide scaffolds were designed and synthesized. The structures of all title compounds were determined by 1 H NMR, 13 C NMR, 19 F NMR and HRMS. Preliminary bioassays suggested that some of the target compounds exhibited remarkable antiviral activities. In particular, compound 4l possessed significant protection activity against tobacco mosaic virus (TMV), with an half maximal effective concentration (EC50) value of 196.11 μg/mL, which was better than commercial agent ningnamycin (447.92 μg/mL). Meanwhile, microscale thermophoresis (MST) indicated that compound 4l have strong binding capability to tobacco mosaic virus coat protein (TMV-CP) with dissociation constant (Kd) values of 0.34 μmol/L, which was better than ningnamycin (0.52 μmol/L). These results suggest that novel myricetin derivatives bearing ferulic acid amide scaffolds may be considered as an activator for antiviral agents.

In 2020 the world experienced the threat of the COVID-19 epidemic, as seniors and chronic disease patients typically try to reduce their exercise and social activities to avoid increasing the risk of infection, which could lead to increased loneliness and even many diseases. This research combining golf croquet games with AIoT companion robots constructs a home-based intelligent exercise system thus uses the Technology Acceptance Model (TAM), deduces users’ intention to use this system based on perceived usefulness and perceived ease of use, and adds the needs of love and belonging, esteem, cognitive, aesthetic, and self-actualization in Maslow’s needs theory to conduct system needs analysis. The analysis results show that participants have a high level of acceptance of this system, believing that it is easy to learn and operate, can increase interaction with others, also found that this system can improve self-confirmation, satisfying the third for knowledge, feeling happy, and self-actualization needs are easier to fulfill. In the future, we shall collect and record the seniors in the process of use, so as to find out their health problems as soon as possible, expand their daily life through this exercise, and achieve the goal of happy living and health care.

In this work, the Ni/Ti/Nb multilayer composite was successfully manufactured by accumulative pack-roll bonding. The microstructure evolution and mechanical properties of the composite during the accumulative roll bonding (ARB) process were investigated by scanning electron microscopy(SEM), energy dispersive spectrometer(EDS), transmission electron microscopy (TEM), micro-hardness and tensile tests. The results showed that after 5 passes of the ARB process, the deformations of layers were relatively uniform, and no large number of interlayer fractures occurred. The microstructures of Ni and Ti were both equiaxed grains with a grain size of 200 nm and 150 nm, respectively, and finer equiaxed grains of the Ni layer were observed at the interface. The laminar structure of Nb layer was observed. The tensile strength and micro-hardness increased significantly as the number of ARB increased. After 5 passes of the ARB process, the tensile strength of the composite reached 792.3 MPa, and the micro-hardness of Ni, Ti, and Nb were increased to 270.2, 307.4, and 243.4 HV, respectively.

Lyme disease, the leading vector-borne ailment in the U.S., annually affects an estimated 476,000 individuals, predominantly in the Northeast and Upper Midwest. Despite its increasing incidence, the evaluation of risk within U.S. cities, including natural public lands, remains inadequate. This study focuses on blacklegged tick occurrences and Borrelia burgdorferi infection prevalence in 24 Staten Island parks, aiming to assess Lyme disease exposure risk. Monthly acarological risk index (ARI) calculations from 2019 to 2022 revealed elevated values (0.16-0.53) in specific parks, notably Wolfe’s Pond Park, High Rock Park, Clay Pit Pond Park, Clove Lake Park, and Fair View Park. June (0.36) and November (0.21) consistently exhibited heightened ARIs, aligning with peak tick collection months. Despite stable yearly infection rates at 28.97%, tick densities varied significantly between parks and years. Identifying a high transmission risk in specific parks in Staten Island, a highly urbanized part of New York City, emphasizes the continuous necessity for Lyme disease risk management, even within the greenspaces of large cities.

With the aging of China's population, the problem of pension security has become more and more prominent, and whether delayed retirement can effectively alleviate the pension fund gap and ensure the sustainability of the pension fund has become the focus of social concern. This study predicts the income and expenditure of urban workers' basic pension insurance fund from 2021 to 2050 by constructing an actuarial model of pension insurance fund income and expenditure, and simulates the effect of delayed retirement policy. The prediction results show that under the existing system, the basic pension insurance fund for urban workers will have a shortfall for the first time in 2027, and the shortfall will expand year by year. Compared with the non-implementation of delayed retirement policy, the simulation of the implementation of delayed retirementt program delayed the emergence of the fund gap until 2029, and the forecast period of the pension fund gap significantly narrowed, indicating that delayed retirement policy has a certain positive impact on alleviating the pressure of pension payments, but delayed retirementt can not completely eliminate the pension fund gap. In view of this, this paper suggests that a progressive and flexible delayed retirement policy should be introduced as soon as possible to better adapt to the needs of different groups. At the same time, differentiated policies should be formulated for different groups of people and a pension incentive mechanism for delayed retirement should be set up to improve public acceptance of delayed retirement policy. In addition, delayed retirement policy should be combined with other measures, such as lowering the corporate contribution rate and enhancing the value-added capacity of the pension fund, so as to ensure the sustainability of the pension fund.

Neonicotinoids (NEOs) have become the most widely used insecticides in the world since the mid-1990s. According to Chinese dietary habits, rice and water are usually heated before being consumed, but the information about the alteration through the heat treatment process is very limited. In this study, the parents of NEOs (p-NEOs) accounted for >99% of the total NEOs mass (∑NEOs) in both uncooked (median: 66.8 ng/g) and cooked (median: 41.4 ng/g) rice samples from Guangdong Province, China, while the metabolites of NEOs (m-NEOs) involved in this study accounted for less than 1%. We aimed to reveal the concentration changes of NEOs through heat treatment process, thus, several groups of rice and water samples from Guangdong were cooked and boiled, respectively. Significant (p < 0.05) reductions in acetamiprid, imidacloprid (IMI), thiacloprid, and thiamethoxam (THM) have been observed after the heat treatment of the rice samples. In water samples, the concentrations of THM and dinotefuran decreased significantly (p < 0.05) after the heat treatment. These results indicate the degradation of p-NEOs and m-NEOs during the heat treatment process. However, the concentrations of IMI increased significantly in tap water samples (p < 0.05) after heat treatment process, which might be caused by the potential IMI precursors in those industrial pesticide products. The concentrations of NEOs in rice and water can be shifted by the heat treatment process, so this process should be considered in relevant human exposure studies.

Robotic systems have been widely used in various industries, so the security of communication between robots and their components has become an issue that needs to be focused on. As a framework for developing robotic systems, the security of ROS2 can directly affect the security of the upper-level robotic systems. Therefore, it is a worthwhile research topic to detect and analyze the security of ROS2. In this paper, we adopt a formal approach to analyze the security of the communication mechanism of ROS2. First, we use a state transition system to model the potential vulnerabilities of ROS2 based on the ROS2 communication mechanism and the basic process of penetration testing. Secondly, we introduce the CIA model on the basis of the established vulnerability model and use LTL to define its security properties. Then, we design and implement a vulnerability detection tool for ROS2 applications based on the vulnerability model and security properties. Finally, we experimentally test some ROS2-based applications, and the results show that ROS2 has vulnerabilities without additional protection safeguards.

Leading and lagging Key performance indicators (KPIs) provide a means for assurance that risk control systems, to prevent or limit major hazards. The relative importance degree of KPIs provides a theorical guidance for monitoring, inspection and maintenance of structural integrity. In this paper, structural integrity KPIs are classified into leading and lagging KPIs based on Bowtie methodology and the importance degree of the KPIs are evaluated by weight calculation on the basis of Fuzzy analytical hierarchy process (FAHP).

A composite flocculant P(AM–DMDAAC) was synthesized by the copolymerization of acrylamide (AM) and dimethyl diallyl ammonium chloride (DMDAAC). Using microwave (MV) assistance with ammonium persulfate as initiator, the synthesis provided short reaction time and better solubility product. Nuclear magnetic resonance spectroscopy (1H NMR and 13C NMR), Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and differential thermal analysis-thermo gravimetric analyzer (DTA-TGA) were used to determine the structure and morphology of P(AM–DMDAAC). Parameters affecting the intrinsic viscosity ([η]) of P(AM–DMDAAC), such as microwave time, mass ratio of DMDAAC to AM, initiator ammonium persulfatedosage, sodium benzoate dosage, bath time, reaction temperature and pH value were examined. Results showed that the optimum synthesis conditions were microwave time 1.5 min, m(DMDAAC): m(AM) is 4:16, 0.5 wt‰ initiator, 0.4 wt‰ EDTA, 0.3 wt‰ sodium benzoate, 2 wt‰ urea, 4 h bath time, 4.0h reaction time and pH 2. To study the removal of phenol by P(AM–DMDAAC), the influence of flocculant dose, pH value and the stirring speed were investigated, with optimization providing 99.8 % removal.

In high-risk railway construction, personal protective equipment monitoring is critical but challenging due to small and frequently obstructed targets. We propose YOLO-EA, an innovative model that enhances safety measure detection by integrating ECA into its backbone's convolutional layers, improving discernment of minuscule objects like hardhats. YOLO-EA further refines target recognition under occlusion by replacing GIoU with EIoU loss. YOLO-EA's effectiveness was empirically substantiated using a dataset derived from real-world railway construction site surveillance footage. It outperforms YOLOv5, achieving 98.9% precision and 94.7% recall, up 2.5% and 0.5% respectively, while maintaining real-time performance at 70.774 fps. This highly efficient and precise YOLO-EA holds great promise for practical application in intricate construction scenarios, enforcing stringent safety compliance during complex railway construction projects.

Aiming to diminish the defects caused by high-speed pulsed GMAW welding, such as non-penetration, non-fusion, humping and undercut, the paper proposed an improved twin-wire double-pulsed high-speed welding process by introducing the impact of additional shielding gas on the welding pool and the effects of different shielding gas flowrates on the microstructure and mechanical properties of the welded seam was investigated. The 2205 duplex stainless steel plate was used as the base material for the butt welding test, and the welded seams were subjected to tensile test, metallographic analysis, hardness analysis, and nondestructive testing. The results indicate that as the flowrate of additional shielding gas increases in the range of 8 L/min~16 L/min, the width of the welded seam increases and the height of reinforcement decreases gradually. However, a grooved seam with a lower middle region and higher sides will appear when the gas flowrate becomes excessively large. The test results indicate that the jet impact force is relatively moderate when the flowrate of the additional shielding gas is 12 L/min and thus, is optimal for the welded seam.

In the neuroscience research field, specific for medical imaging analysis, how to mining more latent medical information from big medical data is significant for us to find the solution of diseases. In this review, we focus on neuroimaging data that is functional Magnetic Resonance Imaging (fMRI) which non-invasive techniques, it already becomes popular tools in the clinical neuroscience and functional cognitive science research. After we get fMRI data, we actually have various software and computer programming that including open source and commercial, it's very hard to choose the best software to analyze data. What's worse, it would cause final result imbalance and unstable when we combine more than software together, so that's why we want to make a pipeline to analyze data. On the other hand, with the growing of machine learning, Python has already become one of very hot and popular computer programming. In addition, it is an open source and dynamic computer programming, the communities, libraries and contributors fast increase in the recent year. Through this review, we hope that can make neuroimaging data analysis more easy, stable and uniform base the one platform system.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

Spirit of science is one of the important components of science education theory. It not only directly affects the level of science education, but also indirectly affects the selection, education and evaluation of scientific researchers, and the development of science and technology in a country or region. Although more than a century ago, the researchers began to discuss the topic of spirit of science. However, to date, the research of the definition, attribute, structural model and its characteristics of the spirit of science has not yet made a breakthrough. Based on the detailed literature review, the related theoretical analysis and the research of the structural model of the spirit of science, this paper puts forward the new definition, the attribute and the establishment of the structural model of the spirit of science, and analyzes the match the situation from new structural model of the spirit of science and the scientific nature published by the American Society for the Advancement of Science. The results of this study are of great significance for raising the level of scientific education and cultivating future scientific researchers, enhancing their motivation and skills in innovation in scientific research and promoting the development of future scientific undertakings.

The objective of this study was to investigate the concentration and spatial distribution patterns of six potentially toxic heavy metal elements (Mn, Zn, Cr, Pb, Cu and Ni) in bus station dusts in the Xifeng district of Gansu province, NW China. The contents were analyzed for Mn, Zn, Cr, Pb, Cu and Ni by using S8 TIGER Brochures wavelength dispersive X-ray fluorescence spectrometry. Geoaccumulation index (Igeo ), enrichment factor (EF), pollution index (PI) and integrated pollution index(IPI) were calculated to evaluate the heavy metal contamination level of bus station dusts. The results indicate that, in comparison with the background values of local soil, bus station dusts in Xifeng have elevated metal concentrations as a whole. The concentrations of heavy metals investigated in this paper are compared with the reported data of other cities. The results show that the arithmetic means of Mn, Zn, Cr, Pb, Cu and Ni are 440.8, 137.9, 60.0, 42.8, 33.5 and 19.8mg kg−1 respectively. The mean values of Igeo reveal the order of Ni<Mn<Cr<Cu<Zn<Pb. The high Igeo and EF for Cu, Zn and Pb in bus station dusts indicate that there is a considerable Cu, Zn and Pb pollution, which mainly originate from traffic and industry activities. The Igeo and EF of Ni, Mn and Cr are low and the assessment results indicate an absence of distinct Ni, Mn and Cr pollution in bus station dusts. The assessment results of PI also support Cu, Zn and Pb in bus station dusts presented middle pollution, and IPI indicates heavy metals of bus station dusts polluted seriously.

Micro/Nano Robot is an intelligent and efficient microrobot that can perform specific tasks under the influence of external stimuli. Depending on the application scenarios, the microrobot can adaptively transform into appropriate functional forms under different external stimuli, thus perfectly matching the needs. To date, microbots have been widely used in targeted therapy, drug delivery, tissue engineering, environmental remediation, and other fields. Although the applications of microrobots are promising, there are only a few reviews that can focus on the preparation methods and driving mechanisms. Therefore, it is necessary to outline the current status of the development of these microrobots in order to provide some new insights for the further development of the field. Therefore, this paper reviews the research progress of microrobots in terms of preparation methods, stimulus response mechanisms and applications, and highlights the applicability of different preparation methods and stimulus types. Finally, the current challenges faced by microrobots are highlighted and possible solutions are proposed to facilitate the practical application of microrobots.

Optical network monitoring and soft failure identification such as optical filter shifting and filter tightening is increasingly significant in the future complex and dynamic optical networks. Center frequency shift of optical filtering device in optical network has a serious impact on the perfor-mance of multi-span transmission, especially in high spectrum efficiency faster-than-Nyquist (FTN) transmission systems with various optical switching and add/drop nodes. Existing moni-toring schemes generally have problem of high cost, high complexity and the inability to realize multi-channel online monitoring, which makes it difficult to be applied in wavelength division multiplexing (WDM) system with numerous nodes. In this paper, a monitoring scheme of fre-quency shift of optical filtering devices based on optical label (OL) is proposed and demonstrated. The signal spectrum of each channel is intentionally divided into many sub-bands with corre-sponding optical labels loading. The characters of spectrum power changing caused by frequency shift can be reflected on labels power changing of each sub-band, which are used to monitor and estimate the value of frequency shift by DSP algorithm. Simulation results shows that the that the monitoring errors of frequency shift can be kept below 0.5GHz reasonably after 10-span WDM transmission in FTN polarization multiplexing m-ary quadrature amplitude modulation (PM-mQAM) systems. In addition, 250km fiber transmission experiments are also carried out and the similar results are obtained, which further verify the feasibility of our proposed scheme. The characters of low cost, high reliability and efficiency make it a better candidate for practical ap-plication in the future FTN WDM networks.

Water resource is considered as a significant factor in development of regional environment and society. Water consumption prediction can provide important decision basis for the regional water supply scheduling optimisations. According to the periodicity and randomness nature of the daily water consumption data, a Markov modified autoregressive moving average (ARIMA) model is proposed in this study. The proposed model, combined with the Markov chain, can correct the prediction error, reduce the continuous superposition of prediction error, and improve the prediction accuracy of future daily water consumption data. The daily water consumption data of different monitoring points are used to verify the effectiveness of the model, and the future water consumption is predicted, in the study area. The results show that the proposed algorithm can effectively reduce the prediction error compared to the ARIMA.

A novel metal-doped carbon quantum dot, zinc-chlorine co-doped carbon quantum dots (Zn/Cl-CQDs), has been developed for the fluorescent probe detection of vitamin B2 and the analysis of the correlation properties of this carbon quantum dot and vitamin B2. Stability experiments demonstrate that Zn/Cl-CQDs possess good fluorescence properties under alkaline conditions. However, when vitamin B2 is added into Zn/Cl-CQDs, the fluorescence intensity decreases sharply, indicating that a fluorescence quenching phenomenon occurs between vitamin B2 and Zn/Cl-CQDs. Lastly, the use of Zn/Cl-CQDs in the detection of vitamin B2 tablets and vitamin B2-rich fruits resulted in recovery rates of 98.2% and 100.6%, respectively. Therefore, this method can be well applied to the detection and analysis of vitamin B2, and has great development prospects in the pharmaceutical industry and food monitoring fields.

Nitrile butadiene rubber (NBR) and its various composites are extensively studied as matrix materials for oil-free lubricated mechanical friction surfaces. While numerous macroscopic friction experiments can compare the frictional performance of different NBR composites, the complex material preparation and low experimental efficiency pose challenges. Nanoscale molecular dynamics (MD) simulations can help develop materials with improved friction properties, but they cannot directly provide the friction coefficients of actual macroscopic friction surfaces. Therefore, it is important to integrate the advantages of macroscopic and nanoscale friction studies and perform a synergistic analysis to modify the friction properties of composite materials. In this study, a multi-scale approach is proposed to simulate the frictional characteristics of carbon nanotube (CNT)-reinforced NBR by combining the MD friction simulation， micromechanical bridging model, and macroscopic finite element analysis (FEA) methods. The results of the multi-scale friction simulation of copper (Cu)-CNT/NBR composites show that the addition of CNTs significantly improves the frictional properties of NBR, and the extent of the improvement is related to the mass fraction of CNTs. As the mass fraction of CNTs increases (0%, 1.25%, 2.5%, 5%), the coefficient of friction decreases from 0.50 to 0.38. The results are validated by ring-block friction experiments at the same scale as the simulations.

Background Dietary guidelines typically recommend limiting the intake of fresh red meat, yet evidence linking red meat consumption with adverse health outcomes is inconsistent. Objective To assess the level of evidence from existing systematic reviews and meta-analyses and analyze the association between high consumption of red meat and cancer risk and adverse health outcomes. Methods Eight databases were searched to collect systematic reviews and meta-analyses from database inception to December 2022. Two independent reviewers screened and extracted data and used the AMSTAR 2 tool to evaluate methodological quality of the included studies. Meta-analysis was conducted using STATA 17.0. Results A total of 18 studies were included, of which 5 were rated as high quality, 4 as medium quality, 6 as low quality, and 3 as extremely low quality. Of the 9 SRs/MAs included, primary studies with overlap were identified, and 14 studies were eventually included. The meta-analysis results showed that compared with the lowest intake of red meat, the highest intake of red meat was associated with an increased risk of colorectal cancer (OR 1.21, 95% CI 1.07-1.37), gastric cancer (OR 1.37, 95% CI 1.18-1.59), non-Hodgkin's lymphoma (OR 1.10.95% CI 1.02-1.19), stroke (RR 1.11, 95% CI 1.03-1.20), type 2 diabetes (RR 1.19 95% CI 1.04-1.37), and ischemic heart disease (RR 1.09, 95% CI 1.06-1.12), as well as a negative effect on total cholesterol (WMD 0.264, 95% CI 0.144-0.383), triglycerides (WMD -0.181, 95% CI -0.349 to -0.013), low-density lipoprotein (WMD 0.198, 95% CI 0.065-0.330), and high-density lipoprotein (WMD -0.065, 95% CI -0.109 to -0.020). However, the associations with breast cancer (RR 1.05 95% CI 1.00-1.11), glycemic control (WMD 0.040, 95% CI 0.049-0.129), and changes in body weight status [overweight (β 0.89, 95% CI 0.48-1.64); obesity (β 1.06, 95% CI 0.30-3.71)] were not significant. Conclusions This comprehensive umbrella review suggests that high consumption of red meat may increase the risk of colorectal cancer, gastric cancer, non-Hodgkin lymphoma, stroke, type 2 diabetes, and cardiovascular disease, and that reducing red meat intake is a key modifiable dietary factor for reducing risk. However, there was no significant correlation with breast cancer, kidney stones, age-related eye disease or changes in body weight.

In this paper, we tackle air quality forecasting by using machine learning approaches to predict the hourly concentration of air pollutants (e.g., Ozone, PM_2.5 and Sulfur Dioxide). Machine learning, as one of the most popular techniques, is able to efficiently train a model on big data by using large-scale optimization algorithms. Although there exists some works applying machine learning to air quality prediction, most of the prior studies are restricted to small scale data and simply train standard regression models (linear or non-linear) to predict the hourly air pollution concentration. In this work, we propose refined models to predict the hourly air pollution concentration based on meteorological data of previous days by formulating the prediction of 24 hours as a multi-task learning problem. It enables us to select a good model with different regularization techniques. We propose a useful regularization by enforcing the prediction models of consecutive hours to be close to each other, and compare with several typical regularizations for multi-task learning including standard Frobenius norm regularization, nuclear norm regularization, ℓ_2,1 norm regularization. Our experiments show the proposed formulations and regularization achieve better performance than existing standard regression models and existing regularizations.

In this nano era, nanomaterials and nanostructures are popular in developing novel functional materials. However, the combinations of nanoproducts with materials at micro and macro scale can open new routes for conceiving novel materials with an improved or even new functional performances. In this study, a brand-new hybrid, containing both nanofibers and particles having a microsize, was fabricated using a sequential electrohydrodynamic atomization (EHDA) process. Firstly, the microparticles loaded with drug (berberine hydrochloride, BH) molecules in the cellulose acetate (CA) were fabricated using a solution electrospraying process. Later, these microparticles were suspended into a co-dissolved solution containned BH and a hydrophilic polymer (polypyrrolidone, PVP), and were co-electrospun into the nanofiber/microparticle hybrids. The EHDA processes were clearly recorded, and the resultant products showed a typical hybrid topography, with microparticles distributed all over the nanofibers, which was demonstrated by SEM assessments. FTIR and XRD demonstrated that the components within the hybrids were presented in an amorphous state and have fine compatibility with each other. In vitro dissolution tests verified that the hybrids were able to provide the designed dula-step drug release profiles, a combination of the fast release step of BH from the hydrophilic PVP nanofibers through an erosion mechanism and the sustained release step of BH from the insoluble CA microparticles via a typical Fickian diffusion mechanism. The present protocols pave a new way for developing trans-scale functional materials.

Over the past four decades, China has experienced a nutritional transition and has developed the largest population of internet users. In this study, we evaluated the impacts of internet access on the nutritional intake in Chinese rural residents. An IV-Probit-based propensity score matching method was used to determine the impact of internet access on nutritional intake. The data were collected from 10042 rural households in six Chinese provinces. The results reveal that rural residents with internet access have significantly higher energy, protein, and fat intake than those without. Chinese rural residents with internet access consumed 1.35% (28.62 kcal), 5.02% (2.61 g), and 4.33% (3.30 g) more energy, protein, and fat, respectively. There was heterogeneity as regards the intake of energy, protein, and fat among those in different income groups. Moreover, non-staple food consumption is the main channel through which internet access affects nutritional intake. The results demonstrate that the local population should use the internet to improve their nutritional status. Further studies are required to investigate the impact of internet use on food consumed away from home and micronutrients intake.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

Channel bends are one of the most important characteristic features of natural streams. These bends often create the conditions for a hyporheic zone, which has been recognized as a critical component of stream ecosystems. The streambed vertical hydraulic conductivity (K_v), vertical hydraulic gradient (VHG) and Darcian flux (DF) in the hyporheic zone were estimated at 61 locations along a channel bend of the Beiluo River during July 2015 and January 2016. All the streambed attributes showed great spatial variability along the channel bend. Both upward fluxes and downward fluxes occurred during the two test periods, most of studied stream sections were controlled by downwelling, indicating stream water discharge into the subsurface. The average downward flux was higher at the downstream side than at the upstream side of the channel bend, especially in July 2015. The distribution of streambed sediment grain size has a significant influence on the variability of K_v; high percentages of silt and clay sediments generally lead to low K_v values. Higher K_v at the depositional left bank at the upstream site shifted toward the erosional right bank at the downstream site, with K_v values positively correlated with the water depth. This study suggested that the variabilities of K_v and VHG were influenced by the stream geomorphology and that the distribution of K_v was inversely related, to a certain extent, to the distribution of VHG across the channel bend. K_v and VHG were found to have opposite effects on the DF, and the close relationship between K_v and DF indicated that the water fluxes were mainly controlled by K_v.

Differences in the physical and chemical properties of reclaimed water (RW) and natural surface water (SW) lead to the differences in terms of nitrogen and phosphorus release when pipeline sediments enter these water bodies. The nitrogen and phosphorus release kinetics from pipe sediments with different particle sizes have been investigated. The results demonstrated that both SW and RW had a pH buffering effect after sediment addition, and the final pH (approximately 8.1) of RW was lower. The release of total phosphorus (TP) and ammonia nitrogen ( NH₄⁺-N) fitted the first-order kinetic model where the release of TP reached equilibrium; TP release was inhibited in both SW and RW, where RW exhibited the lowest (by a factor of 1.23~2.44) release (0.002 mg/g). The release of NH4+-N was promoted in both SW and RW; the maximum release in RW was 0.0188 mg/g. The amounts of NH₄⁺-N released in SW and RW were 1.02-1.40 and 1.30-1.80 times that of the control group (CG), respectively. The percentage of TP and NH₄⁺-N release in the three groups was highest in 75-154 μm pipe sediment, reaching 34.53% and 43.51% in SW and RW, respectively. These results can assist in the development of water quality evolution models for specific urban scenarios, and provide important guidance for the precise regulation of recharge water quality during and after rainfall.

Topology optimization is a pioneering design method that can provide various candidates with high mechanical properties. However, the high-resolution for the optimum structures is highly desired, normally in turn leading to computationally intractable puzzle, especially for the famous Solid Isotropic Material with Penalization (SIMP) method. In this paper, an efficient and high-resolution topology optimization method is proposed based on the Super-Resolution Convolutional Neural Network (SRCNN) technique in the framework of SIMP. The SRCNN includes four processes, i.e. refining, path extraction & representation, non-linear mapping, and reconstruction. The high computational efficiency is achieved by a pooling strategy, which can balance the number of finite element analysis (FEA) and the output mesh in optimization process. To further reduce the high computational cost of 3D topology optimization problems, a combined treatment method using 2D SRCNN is built as another speeding-up strategy. A number of typical examples justify that the high-resolution topology optimization method adopting SRCNN has excellent applicability and high efficiency for 2D and 3D problems with arbitrary boundary conditions, any design domain shape, and varied load.

Geological structures such as joints and faults in rock mass have significant influence on open pit mining. Hence, it is critical to develop a understanding of dynamic joint behaviour under blasting loading. This in turn can provide both theoretical and practical guidance to improve blasting rock fragmentation and associated bucket excavating efficiency. In this paper, delayed blasting on the highwall bench at Baiyunebo open-pit mine was used as an example, a nonlinear joint blasting model was also constructed. By simplifying the blasting wave propagation velocity, the P-wave normal incidence to the joint was obtained. The peak vibration velocity was 0.33m/s at 3.0s. The S-wave reflected by the joint interface was first reflected backward and then forward, which the peak vibration velocity was 0.027 m/s. By combining the relevant stress and displacement theories of type I and II cracks, the equipotential diagrams of the stress and displacement field with the vibration velocity of the particle were obtained. σx was positive in the direction of 0~330° and subjected to tensile stress, whereas σy was positive in the direction of 0~180° and under tensile stress. The longitudinal σy along joint was low in compressive stress distribution area and did not affect surrounding rock at the time. The stress concentration appeared in the lower right corner. Based on the continuous behavior of stress wave in joints, the asymmetry and continuous changes reflected in the whole process could not be analysed by the contour diagram. Hence, ANSYS used to analyse distribution of the stress field. The intensity of the shock wave after detonation was greater than that of the rock strength. Subsequently, the sub-layer shock wave supplemented the shock wave energy that was not enough to break the rock and induced further cracking. This was able to be visualized by the degree of color change post-processing. It was concluded that with the attenuation of the detonation wave energy, the stress exhibited a decreasing trend in this process. According to distribution of the peak effective stress, it was found that the peak value first increased to 10-12 MPa and then showed a downward trend. Overall, the results were validated against the finite element simulation and mathematical analysis.

Container crane has been widely used for port operation. However, the structure of port container crane is large, which always lead to crane damage under the vibration and strong wind. Therefore, a method for vibration reduction of container crane structure based on particle damping technology is proposed. In this investigation, the scale 1:80 crane model is built, the equivalent mechanical model is also established to preliminary verify the effect of vibration suppression. Furthermore, the dependence of vibration suppression effect on the key parameters of the damper, i.e., filling material, filling rate, particle size, and installation position of dampers are analyzed through experiments. The results indicate that the vibration peak of the crane structure displayed in Simulink oscilloscope is weakened and lags behind, the installation of the damper brings the effect of vibration suppression for the crane, the vibration suppression effect reaches 25%; the crane mode obtains the best vibration suppression effect under the condition that the material filled in the damper has a large density and elastic modulus, sufficient collision space and high collision frequency, and the dampers are installed far away from the crane center of gravity. The optimum parameters of the damper obtained from experiments, 12 mm lead beads, filling rate of 60%, installed in the distal ends within the strength range of the forearm of the crane. It is thus concluded that the particle damping technology has provided an effective way in wind and vibration reduction for container crane.

Osteoporosis (OP), a prevalent skeletal disorder characterized by compromised bone strength and increased susceptibility to fractures, poses a significant public health concern. This review aims to provide a comprehensive analysis of the current state of research in the field, focusing on the application of proteomic techniques to elucidate diagnostic markers and therapeutic targets for OP. The integration of cutting-edge proteomic technologies has enabled the identification and quantification of proteins associated with bone metabolism, leading to a deeper understanding of the molecular mechanisms underlying OP. In this review, we systematically examine recent advancements in proteomic studies related to OP, emphasizing the identification of potential biomarkers for OP diagnosis and the discovery of novel therapeutic targets. Additionally, we discuss the challenges and future directions in the field, highlighting the potential impact of proteomic research in transforming the landscape of OP diagnosis and treatment.

This study presents an exploration into identifying the interactions between ocean waves and the continental margin in the origination of double-frequency (DF, 0.1-0.5 Hz) microseisms recorded at 33 stations across East Coast of USA (ECUSA) during a ten-day period of ordinary ocean wave climate. Daily primary vibration directions are calculated in three frequency bands and projected as great circles passing through each station. In each band, the great circles from all stations exhibit largest spatial density primarily near the continental slope in the western North Atlantic Ocean. Generation mechanisms of three DF microseism events are explored by comparing temporal and spatial variations of the DF microseisms with the migration patterns of ocean wave fronts in Wavewatch III hindcasts. Correlation analyses are conducted by comparing the frequency compositions of and calculating the correlation coefficients between the DF microseisms and the ocean waves recorded at selected buoys. The observations and analyses lead to a hypothesis that the continental slope causes wave reflection, generating low frequency DF energy and that the continental shelf is where high frequency DF energy is mainly generated in ECUSA. The hypothesis is supported by the primary vibration directions being mainly perpendicular to the strike of the continental slope.

Species data of 249 National Nature Reserves in China was used to identify potential underlying drivers of latitudinal gradients in plant diversity. We used generalized linear models (GLMs) to assess the correlations between predictor and response variables. We also used SAM (Spatial Analysis in Macroecology) to eliminate autocorrelation along each of the 249 studied locations. We used the Akaike information criterion (AICc; Montoya et al. 2007) to select the independent variables were those included in the best models from different combinations of climate, habitat and animal variables. Variance partitioning was used to decompose the variation in plant richness across different taxonomic levels among the three groups of predictors. We found that: Total plant species, gymnosperms, angiosperms and ferns showed significant latitudinal trends in richness (p < 0.001). Water-energy and habitat variables generally explained more variation in richness across different plant groups than did animal richness. Annual precipitation was selected as the best water-energy variable across different taxonomic plants groups, soil PH and elevation range were selected as the best habitat variables across different taxonomic plant groups. The independent effects of habitatvariables were higher than that of water-energy and animal variables across different taxonomic plants groups. Water-energy, habitat heterogeneity, and animal variables explain 48.8% of the variation in total species richness, 28.2% in gymnosperm richness, 44.2% in angiosperm richness, and 38.9% in fern richness.Plants showed significant latitudinal trends in richness (p < 0.001). Water-energy and habitat variables generally explained more variation in richness across different taxonomic plants groups than did animal variables. The independent effects of habitat variables were higher than those of water-energy and animal variables across different taxonomic plants groups.

This study derives space travel pricing by Walrasian Equilibrium, which is logical reasoning from the general relativity theory (GRT), the accounting equation, and economic supply and demand functions. The Cobb-Douglas functions embed the endogenous space factor as new capital to form the space travel firm's production function, which is also transformed into the consumer's utility function. Thus, the market equilibrium occurs at the equivalence of supply and demand functions, like the GRT presents the equivalence between the spatial geometric tensor and the energy-momentum tensor, which explains the principles of gravity and the motion of space matter in the spacetime framework. The mathematical axiomatic set theory of the accounting equation explains the equity premium effect that causes a short-term accounting equation inequality, then reaches the equivalence by suppliers' incremental equity through the closing accounts process of the accounting cycle. On the demand side, the consumption of space travel can be assumed as a value at risk (VaR) investment to attain the specific spacetime curvature in an expected orbit. Spacetime market equilibrium is then achieved to construct the space travel pricing model. The methodology of econophysics and analogy method was applied to infer the space travel pricing by the model of profit maximization, single-minded, and envy-free pricing in unit-demand markets. A case study with simulation was conducted for empirical verification of the math models and algorithm. Results show that space travel pricing remains the principle of market equilibrium but needs to be extended to the spacetime tensor of GRT.

The weight coefficients of the diaphragm spring depend on experiences in the traditional optimization. However, this method not only cannot guarantee the optimal solution but it is also not universal. Therefore, a new optimization target function is proposed. The new function takes the minimum of average compress force changing of the spring and the minimum force of the separation as total objectives. Based on the optimization function, the result of the clutch diaphragm spring in a car is analyzed by the non-dominated sorting genetic algorithm (NSGA-II) and the solution set of Pareto is obtained. The results show that the pressing force of the diaphragm spring is improved by 4.09%by the new algorithmand the steering separation force is improved by 6.55%, which has better stability and steering portability. The problem of the weight coefficient in the traditional empirical design is solved. The pressing force of the optimized diaphragm spring varied slightly during the abrasion range of the friction film, and the manipulation became remarkably light.

To promote low-carbon and green travel, this study proposes a tripartite evolutionary game model among new energy vehicle manufacturers, consumers, and government agencies. The game strategy combinations of each party and the stability conditions of the equilibrium point in the evolutionary game system are analyzed, and the validity of the conclusions is verified through simulation results. The study shows a strong correlation between the three parties in the evolutionary game system. From the perspective of car manufacturers, the probability of producing new energy vehicles is positively proportional to the subsidy received from new energy policy, the additional revenue gained from the management of the carbon trading scheme, and the fine received for producing conventional fuel vehicles. However, from the consumer perspective, the likelihood that consumers purchase new energy vehicles is positively related to the utility value to consumers and the coverage of public charging points in the city, and inversely related to the sales price of new energy vehicles. From the government perspective, a combination of direct subsidy policies and indirect support strategies should be considered to stimulate the rapid development of the new energy vehicle industry.

Additive manufacturing (AM) offers customization of microstructure and mechanical properties of fabricated components according to the material selected, and process parameters applied. Selective laser melting (SLM) is the commonly used technique for processing high strength aluminum alloys. Selection of SLM process parameters could control the microstructure of parts and their mechanical properties. However, the process parameters limit and defects obtained inside the as-built parts present obstacles to customized part production. This study investigates the influence of SLM process parameters on the quality of as-built Al6061 and AlSi10Mg parts according to the mutual connection between the microstructure characteristics and mechanical properties. The microstructure of both materials was characterized for different parts processed over a wide range of SLM process parameters. The optimized SLM parameters were investigated to eliminate the internal microstructure defects. The behaviour of mechanical properties of parts was presented through regression models generated from the design of experiment (DOE) analysis for the results of hardness, ultimate tensile strength, and yield strength. A comparison between the results obtained and that reported in the literature is presented to illustrate the influence of process parameters, build environment, and powder characteristics on the quality of parts produced. The results obtained from this study could help to customize the part’s quality by satisfying their design requirements in addition to reducing the as-built defects which in turn reduce the amount of the post-processing needed.

Synthesis of poly(o-phenylenediamine) (PoPD) and poly(o-phenylenediamine)-ZnO (PoPD-ZnO) nanocomposites on carbon steel by in-situ polymerization with HCl acid as doping acid Material coating. The composition and structure of PoPD-ZnO nanocomposites were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) and scanning electron microscopy (SEM). The corrosion protection ability of polymer coatings in 3.5% NaCl was studied by potentiodynamic polarization curves and electrochemical impedance spectroscopy. It can be seen from the electrochemical corrosion experimental data that PoPD-WPU coating (PWC) and PoPD-ZnO-WPU coating (PZWC) can effectively improve the corrosion resistance of the carbon steel substrate, and the corrosion rate is reduced by 2-3 orders of magnitude compared with carbon steel. The conclusion demontrates that PoPD can effectively extend the service life of carbon steel substrates. In addition, it is advantageous to form a compact and low-defect coating when added nano-particle ZnO, which is advantageous for the POPD film to develop its good barrier property and corrosion resistance.

In this paper, a semi-empirical model of air waves induced by falling rock is described. The model is composed of a uniform motion phase (velocity close to 0 m·s^-1) and an acceleration movement phase. The uniform motion phase was determined based on experimentally and the acceleration movement phase was derived by theoretical analysis. A series of experiments were performed to verify the semi-empirical model and elucidated the law of the uniform motion phase. The acceleration movement phase accounted for a larger portion with a greater height of the falling rock. Experimental results of different falling heights of the goaf showed close agreement with theoretical analysis values. The semi-empirical model could accurately and conveniently estimate the velocity of air wave induced by falling rock. Thus, the semi-empirical model can provide a reference and basis for estimating the speed of air waves and designing protective measures in mines.

The current outbreak of coronavirus disease (COVID-19) caused by SARS-CoV-2 in Wuhan, China has killed more than 2600 people since December 2019. Currently there is no effective treatment for this epidemic. Drug for anti SARS-CoV-2 are urgently needed. In this study we evaluated two compound libraries containing launched drugs and compounds from 300 kinds of Traditional Chinese Medicine in order to find anti SARS-CoV-2 drugs. Docking and then calculating binding free energy were performed as workflow against four key anti-SARS-CoV-2 drug targets, 3CLpro, PLpro and RdRp from SARSCoV-2, and AAK1 from human as well. As a result, drugs launched with potential for antiviral usage were selected in the hope of providing some knowledge for future drug discovery.

In this paper, the methods and their analysis for estimating the location of three dimension (3-D) single source buried in lossy medium are presented with uniform circular array (UCA). The mathematical model of the signal in the lossy medium is proposed. Using location information in the covariance matrix obtained by sensors’ output, the equations of the source location (azimuth angle, elevation angle and range) are obtained. The phase and amplitude of the covariance matrix function are used to process these equations respectively. Then, the phase and amplitude of the covariance matrix function are used to process the source localization in the conductive medium together. By analyzing the characteristics of the proposed methods and MUSIC method, the computational complexity and the valid range of these methods are given. From the results, whether the loss is known, we can choose the appropriate method to process the issues (localization in lossless medium or lossy medium).

A novel verifiable privacy preservation scheme for outsourcing medical image to cloud through ROI based crypto-watermarking is proposed in the paper. In the proposed scheme, data owner firstly carries out substitution of S-box for the region of interest (ROI) of medical image, and then separates the image into 4 most significant bits (MSBs) plane and 4 least significant bits (LSBs) plane images. Secondly, the hash value of ROI is embedded into the two separated bit plane images using reversible watermarking algorithm. Lastly, some selected hash values are transformed into the initial parameters of chaotic maps, and the two sharing secrets, which are produced through chaos based encryption algorithm, are finally outsourced to two different cloud servers. For authorized users, they can get shares from different cloud servers, and then can losslessly recover the original medical image through a series of decryption operations and extraction of watermarking. Furthermore, the users can verify whether the original image is completely reconstructed or not, they even can locate the tampered parts inside ROI if anyone of the sharing secrets is damaged. Some experiments analyses and comparisons are given to show the security and effectiveness of proposed scheme.

Background: Along with sarcopenia, delayed blood pressure (BP) recovery after standing and orthostatic hypotension (OH) are among key clinical challenges associated with ageing. Previous studies have reported an association between sarcopenia and delayed orthostatic BP recovery and OH. However, the haemodynamic mechanisms underlying this association remain unclear. Methods: 107 attendees to a falls and syncope clinic aged 50+ years underwent an active stand test with non-invasive beat-to-beat haemodynamic measurement. Hand grip strength and 5-chair stands time were measured. Muscle mass was estimated using bioelectrical impedance analysis, and participants were classified as non-sarcopenic and sarcopenic. Mixed effects models with linear splines were used to model the effect of sarcopenia status on Modelflow®-derived mean arterial pressure (MAP), cardiac output (CO), total peripheral resistance (TPR), stroke volume (SV) and heart rate (HR) after standing, while controlling for potential confounders. Results: Sarcopenia was associated with: attenuated recovery of MAP in the 10-20s period after standing (β -0.67, P<0.001); attenuated rise to peak (0-10s) and recovery from peak (10-20s) of CO (β -0.05, P<0.001; β 0.06, P<0.001); attenuated recovery (10-20s) of TPR from nadir (β -0.02, P<0.001) and attenuated recovery from peak (10-20s) of SV (β 0.54, P<0.001). HR was not significantly associated with sarcopenia status at any time interval after standing. Conclusion: The attenuated BP recovery after standing seen in sarcopenia appears to be driven by initial diminished peak of CO followed by attenuated recovery of CO from peak and TPR from nadir. The CO finding appears to be driven by SV rather than HR. Potential mechanisms for these findings include: cardio-sarcopenia, the effects of sarcopenia on the autonomic nervous system and/or the skeletal muscle pump.

Due to the long-term deformation settlement of foundations, issues such as damage and functional failure of buildings and structures have long been of concern in the engineering field. The creep of soil is one of the primary causes leading to long-term deformation of foundations. In this paper, the consolidation deformation, creep characteristics, and creep model of reconstituted saturated silty clay were studied by isotropic compression test and triaxial shear creep test. The results show that for the isotropic compression test, although the applied load adopts different stages of loading, as long as the final applied confining pressure is the same, the number of stages applied by the confining pressure has little effect on the final isotropic consolidation deformation of the sample and the triaxial undrained shear strength after creep. However, for the triaxial shear creep test, it is found that under the same final deviatoric stress, the final deviatoric strain of the sample is closely related to the number of loading stages of deviatoric stress. It shows that the more loading stages of the sample loaded with the same deviatoric stress, the smaller the final deviatoric strain, and the triaxial undrained shear strength of the sample after creep will increase. In addition, it is reasonable to determine the pore pressure dissipation of the sample to 95%((u0-u0)/u0=95%) as the main consolidation end time (tEOP) of the sample. The isotropic consolidation creep curves and the triaxial shear creep curves show certain nonlinearity. Then the logarithmic model and the hyperbolic model were used to fit the creep curves of the samples. It is found that the hyperbolic model has a better fitting effect than the logarithmic model, but for the triaxial shear creep test, the creep parameters of the sample change greatly. Therefore, studying the creep characteristics of soil under different pre-loading steps is of significant engineering importance for evaluating the long-term deformation of underground structures.

Background: The COVID-19 outbreak has accelerated the huge difference between medical care and disease prevention in Chinese medical institutions. This study aimed to investigated the relationship between the symbiotic units, environments, models, and effects of the integration of medical and disease prevention. Methods: This cross-sectional study involved 762 employees of public hospitals in 11 cities in Zhejiang Province by random stratified sampling. We analyzed the influence paths of elements in the mechanism of integration of medical and disease prevention and the mediating effect of symbiotic models among symbiotic units, symbiotic environments, and effects for on this integration. Results: The path coefficient of symbiotic unit on the symbiosis model was 0.46 (p&lt;.001), the path coefficient of symbiotic environment on symbiosis model was 0.52 (p&lt;.001). The path coefficient of the symbiotic unit and environment was 0.91 (p&lt;.001). The symbiotic models exhibited a partial mediation effect between symbiotic units and the effect of this integration. Sobel test = 3.27, β = 0.152, and the mediating effect accounted for 34.6%. Conclusions: It is suggested that Health policy-makers and public hospital managers should provide sufficient symbiotic units, establish collaborative symbiotic models, and improve the effects of integration of medical and disease prevention in public hospitals.

Predators are dependent on the capture of prey to meet their energetic and nutritive requirements, imposing a regime of predation risk. Consequently, prey experience both consumptive and non-consumptive effects. Non-consumptive effects may manifest through altered growth and ontogenetic trajectories of prey species, a dynamic modulated by olfactory or other sensory cues from predators. Bactrocera dorsalis Hendel represents a great invasive threat to global horticulture. While earlier research has primarily centered on the consumptive interactions between B. dorsalis and its natural enemies, the potential consequences of non-consumptive interactions on the development of B. dorsalis have been overlooked. In this study, we investigated the impact of predation risk effects, induced by both visual exposure to the predatory mantis Hierodula patellifera Serville and its associated odor, on the life history traits of B. dorsalis. Female B. dorsalis demonstrated reduced development time in the presence of isolated H. patellifera or H. patellifera odor, yet evidenced significantly increased fecundity. Conversely, males displayed no significant change in development time. Additionally, neither female nor male body weight at death was significantly influenced by predation risk from isolated predators or predator odor. These results indicated adaptive developmental strategies of B. dorsalis when faced with risks from predators and highlight the important role of predator odor, which has the potential to lay the groundwork for improving biological control efforts and innovative approaches within pest control.

This study extends the CGAN-based MODIS cloud vertical-profile (64×64-scene, about 70km width×15km height) retrieval technique developed by Leinonen et al. (2019) [1] to construct seamless 3D cloud fields for the MODIS granules [2]. Firstly, the accuracy and spatial continuity of the Leinonen et al. [1] retrievals are statistically evaluated. Then, according to the characteristics of the retrieval error, a spatially overlapping-scene ensemble generation method and a bi-directional Ensemble Binning Probability Fusion (CGAN-BEBPF) technique are developed, which improves the CGAN retrieval accuracy and support to construct seamless 3D clouds. The CGAN-BEBPF technique involves three steps: cloud masking, intensity scaling, and optimal value selection. It ensures adequate coverage of the low reflectivity areas while preserving the high reflectivity cloud cores. The technique is applied to retrieve the 3D cloud fields of Typhoon Chaba and a multi-cell convective system. The cloud structures of the CGAN-BEBPF results are highly consistent with the ground-based radar observations. It can retrieve weak clouds at the top levels of convective storms and hurricanes that were missed by ground-based radars and fill the gaps of the ground-based radar lower-level PPI scan. Overall, CGAN-BEBPF can be automated to retrieve the rich informative 3D structures of typhoons and severe convective systems over the oceans along the MODIS swath, which certainly presents great value for improving maritime and near-shore typhoons and convection prediction and other cloud-sensitive applications.

In order to study the collapse failure of shaft wall of high depth inclined ore-pass under ore impact wear behavior, 25 ore-passes in a deep mine in Yunnan, China were investigated. Considering the ore-pass structural characteristics and the impact wear effect of ore on shaft wall, the shaft wall damage model of high depth inclined ore-pass is constructed based on the contact mechanics theory. Furthermore, No. 1#, 2#, 3# and 9# ore-passes of the mine are taken as examples for analysis, and the three results of theoretical analysis, numerical simulation and engineering case are used for comparison and verification. The shaft wall damage degree is predicted, and the damage mechanism between total shaft wall damage volume Qtol and ore-pass depth H, ore-pass dip angle θ, inclined angle of chute α, shaft diameter D and ore block size P is quantitatively investigated. The results show that the rationality of the proposed model is verified by numerical analysis and field engineering situations. Moreover, the deeper ore-pass depth H, the more shaft wall damage volume Qtol with the increase of collision frequency. Qtol increases exponentially with P and increases gradually with D. With the increase of θ or α, Qtol increases generally first and then decreases. Therefore, Qtol can be effectively reduced by selecting the appropriate structure parameters of ore-pass and adopting the technology of drilling straight ore-pass. This work provides technical support for long period safe operation of high depth inclined ore-pass.

Fusarium dry rot is one of the major postharvest potato diseases of during storage after harvest, which not only results in quality degradation but also brings up huge economic losses. The dis-ease can be elicited by some species of Fusarium, the pathogenic fungi of Fusarium causing potato dry rot are considerably diverse in various countries and regions. Fusarium spp. infection is as-sociated with dry rot produce mycotoxins, which has phytotoxicity and mycotoxicoses on hu-mans and animals. Chemical synthetic fungicide is considered as the main control measure to Fusarium dry rot of potato, nevertheless, it is unfortunate that the persistent application inevitably results in the emergency of resistant strain and environmental contamination. A comprehensive disease control strategy includes potato cultivar selection, appropriate cultural practices (crop rotation, cultivate pattern, fertilization, and irrigation), harvesting process and postharvest treatment (harvesting, classification, packaging, wound healing), storage condition (environ-mental disinfection, temperature, humidity and gas composition) along with the application of fungicide pre-harvest or postharvest. Recently, emerging studies indicated that eco-friendly strategies include physical control, chemical methods (such as the application of generally rec-ognized as safe (GRAS) compounds or chemical (elicitors) and biological control have been in-troduced to combat Fusarium dry rot of potato.

With the recent developments in augmented reality (AR) technologies comes an increased interest in the use of smart glasses for hands-on training. Whether this interest is turned into market success or not depends at the least on whether the interaction with smart AR glasses satisfies users, an aspect of AR use that so far has received little attention. With this contribution, we seek to change this. The objective of the article, therefore, is to investigate user satisfaction in AR applied to three cases of practical use. User satisfaction of AR can be broken down into satisfaction with the interaction and satisfaction with the delivery device. A total of 142 participants from three different industrial sectors contributed to this study, namely, aeronautics, medicine, and astronautics. In our analysis, we investigated the influence of different factors, such as age, gender, level of education, level of Internet knowledge, and the roles of the participants in the different sectors. Even though users were not familiar with the smart glasses, results show that general computer knowledge has a positive effect on user satisfaction. Further analysis using two-factor interactions shows that there is no significant interaction between the different factors and user satisfaction. The results of the study affirm that the questionnaires developed for user satisfaction of smart glasses and the AR application performed well, but leave room for improvement.

In addition to provide an extremely clean environment for primary loop of high-temperature gas-cooled reactor (HTR), the primary helium circulator (PHC) using electromagnetic levitation technology also provides an effective means for vibration control. Besides synchronous vibration produced by mass imbalance and sensor runout, double-frequency vibration produced by unbalanced magnetic pull (UMP) is serious in PHC engineering prototype (PHC-EP). In this paper, we firstly analyzed the mechanism of UMP and the multi-frequency vibration characteristics in combination with the PHC-EP. Then we put forward a distributed iterative learning control (ILC) algorithm and a parallel control scheme to suppress the periodic vibrations. Finally, we verified the methods by carrying out experimental researches on the active magnetic bearing (AMB) bench of PHC-EP. The results show that the methods put forward in this paper have significant control effect on the double-frequency vibration generated by UMP of the PHC-EP, and provide theoretical and practical references for the PHC safe operation in HTR.

In the new period, the state has made every effort to promote the new urbanization of public sports service. Entropy method, coupled coordination model, cold hot spot analysis is used to explore the dynamic relationship between public sports services and the development of new urbanization in China from 2008 to 2017. The results show that: (1) The development of the internal subsystem of public sports service is not balanced, the sports financial investment system grows rapidly, but the development of professional sports talent team is slow. (2) The imbalance of regional development cannot be ignored, and the public sports service level shows a decreasing gradient from east to west. (3) The regional development features are different. The eastern region is dominated by the coordinated development of sports public service and urbanization, while the central region is mainly in the type of public sports service lag, while the western region has multiple complex characteristics of low-level coordination and public sports service lag. Therefore, it is proposed that the construction of modern public sports service system should be investigated in the context of the development of new urbanization. It should be promoted from the following aspects: promoting the extension of public sports service to rural areas, engendering the "citizen's right" of sports health to the migrant population, conforming to the trend of mass sports intelligence, developing green sports and revitalizing idle sports assets in cities.

Plant cells' ability to withstand abiotic stress is strongly linked to modifications in their mechanical characteristics. Nevertheless, the lack of a workable method for consistently tracking plant cell mechanical properties severely restricts our comprehension of the mechanical alterations in plant cells under stress. With Polyethylene Glycol (PEG6000), we created a drought-like environment, and we used the Double Resonator Piezoelectric Cytometry (DRPC) method to dynamically and non-invasively track changes in the stress (ΔS) created and viscoelasticity (storage modulus G' and loss modulus G") of protoplasts and suspension cells of rice during drought stress. The findings demonstrate that, rice suspension cells and protoplasts react mechanically differently to 5%–15% PEG6000 stress, implying distinct resistance mechanisms. However, neither of them can withstand 25% PEG6000 stress, they respond mechanically similarly to 25% PEG6000 stress. The results of DRPC are further corroborated by the morphological alterations of rice cells and protoplasts observed under an optical microscope. To sum up, the DRPC technique functions as a precise cellular mechanical sensor and offers novel research tools for the evaluation of plant cell adversity and differentiating between the mechanical reactions of cells and protoplasts under abiotic stress.

Carotid atherosclerotic lesions are a major cause of cerebrovascular disease (CVD). Identification and quantification of carotid plaques are important for categorizing the vulnerability of plaques for rupture and assessing the impact of treatments. The irregularity of plaque surface is associated with previous plaque rupture and plays an important role in the risk of stroke. Thus, the aim of this study is to develop and validate novel vulnerability biomarkers from three-dimensional ultrasound (3DUS) images by analyzing the surface morphological characterization of carotid plaque using fractal geometry features. 3D box-counting and 3D blanket are the two types of 3D fractal dimension that were employed to describe the smoothness of plaques. This fractal dimension analysis tool was used to evaluate the effect of atorvastatin using 3DUS carotid images, which were acquired from 6 patients treated with atorvastatin with 80 mg daily and 5 patients with placebo. The Student's T Test results showed that those two fractal features were effective for detecting the statin-related changes in carotid atherosclerosis with p<0.0068 and p<0.015 respectively, suggesting that 3D fractal dimension measurements can be used effectively to analyze the surface characteristics of carotid plaques, especially for evaluating the impact of the treatment.

Rhododendron chrysanthum Pall., live in Changbai Mountain being exposed to chilling temperature, high light intensities and water scarcity condition. To adapt to the harsh environment, the cold resistance mechanisms of R. chrysanthum have been successfully evolved in the long-term adaptive process. In our present work, the methods of proteomics combined with physiological and biochemical analyses were used to investigate the effects of cold stress on the photosynthesis and antioxidant system of Rhododendron chrysanthum Pall. and the molecular mechanisms involved in cold resistance of plants. A total of 153 photosynthesis related proteins were identified in present work, of which 7 proteins including Rubisco large subunit (rbcL) were up-regulated in experiment group (EG) compared with control group (CG). Simultaneously, four chlorophyll fluorescence parameters were measured in present study. The results showed that the maximum photochemical efficiency of photosystem II (Fv/Fm), actual quantum yield of PSII (Y(II)) and photochemical quenching (qP) were significantly higher in EG, whereas the non-photochemical quenching (NPQ) was notably decreased. Cold stress could lead to a significant reduction in electron transport rate (ETR) accompanied with an increase in excitation pressure (1-qP). The abundance of PetE which involved in the plants photosynthetic electron transfer was also significantly influenced by cold stress. Moreover, the up-regulated expressions and higher levels of enzymatic activities of Glutathione peroxidase (GPX) and Ascorbate peroxidases (APXs) were detected in EG. All these changes which can help plants to survive in low temperature are considered as the crucial parts of cold tolerance mechanisms. These results revealed that photosynthesis and redox adjustment play significant roles in the defense of cold-induced damage.

The prediction of stock prices holds significant implications for researchers and investors in evaluating stock value and risk. In recent years, researchers have increasingly replaced traditional machine learning methods with deep learning approaches in this domain. However, the application of deep learning in forecasting stock prices is confronted with the challenge of overfitting. To address the issue of overfitting and enhance predictive accuracy, this study proposes a stock prediction model based on GRU (Gated Recurrent Unit) with reconstructed datasets. This model integrates data from other stocks within the same industry, thereby enriching the extracted features and mitigating the risk of overfitting. Additionally, an auxiliary module is employed to augment the volume of data through dataset reconstruction, thereby enhancing the model’s training comprehensiveness and generalization capabilities. Experimental results demonstrate a substantial improvement in prediction accuracy across various industries.

In the world city theory, most researchers focus on the service sector in the urban economy and less discuss the role of manufacturing. However, the path of only emphasizing financial and corporate service could not fit the sustainability concept. Compared to Anglo-American world city, Global South’s world cities have distinct pathway to be industrialization, tertiarization and globalization. This paper adopted dynamic historic perspective with first-hand materials including in-depth interviews with managers and government officers and second-hand data including yearbook statics and economic census to closely examine the emerging world city-- ‘World Factory’ in Global South, Guangzhou in China, from 1949 to 2015, to emphasize how manufacturing affects the urban globalization through three dimensions, economic, social and spatial dimensions. To make the confirmation of the role of manufacturing in Guangzhou as sustainable world city, we find manufacturing in Guangzhou builds up the basic foundation of export-oriented economy and makes positive effects on urban economic transformation. In addition, manufacturing remains important source of employment and foreign immigration. Along with urbanization and industrialization, urban spatial expansion and aggregation changes with different urban development concept. We provide new insights on multiple globalization on manufacturing for sustainable world city.

The performance of the absolute atom gravimeters used on moving platforms, such as vehicles, ships and aircrafts, is strongly affected by the vibration noise. To suppress its influence, we summarize a vibration compensation method utilizing data measured by a classical accelerometer. The measurements with the accelerometer show that the vibration noise in the vehicle can be 2 order of magnitude greater than that in the lab during daytime, and can induce an interferometric phase fluctuation with a standard deviation of 16.70π. With the compensation method, our vehicle-mounted atom gravimeter can work normally in these harsh conditions. Comparing the Allan standard deviations before and after the vibration noise correction, we find a suppression factor of 22.74 can be achieved in static condition with an interrogation time of T = 20 ms, resulting a sensitivity of 1.35 mGal/Hz1/2, and a standard deviation of 0.5 mGal with an average time of 10 s. We also demonstrate the first test of an atom gravimeter in a moving vehicle, in which a suppression factor of 50.85 and a sensitivity of 60.88 mGal/Hz1/2 were realized with T = 5 ms.

In order to better understand the source-sink flow and relationships of Zinc (Zn) and other nutrients in wheat (Triticum aestivum L.) plants for biofortification and improving grain nutritional quality, effects of reducing photoassimilate source (through the flag leaf removal and spike shading) or sink (through 50% spikelets removal) in the field on accumulation of Zn and other nutrients in wheat grains of two cultivars (Jimai 22 and Jimai 44) were investigated under two soil Zn application levels. The single panicle weight (SPW), kernel number per spike (KNPS), thousand kernel weight (TKW), total grain weight (TGW), concentrations and yields of various nutrient elements (Zn, Fe, Mn, Cu, N, P, K, Ca and Mg), phytate phosphorus (phytate-P), phytic acid (PA) and phytohormones (ABA: abscisic acid, and the ethylene precursor ACC: 1-aminocylopropane-1-carboxylic acid), and C/N ratios were determined. Soil Zn application significantly increased concentrations of grain Zn, N and K. Cultivars showing higher grain yields had lower grain protein and micronutrient nutritional quality. SPW, KNPS, TKW (with an exception of TKW in half spikelets removal), TGW, and nutrient yields in wheat grains were most severely reduced by half spiklets removal, secondly by spike shading, and slightly by flag leaf removal. Grain concentrations of Zn, N and Mg consistently showed negative correlations with SPW, KNPS and TGW, but positively with TKW. There were general positive correlations among grain concentrations of Zn, Fe, Mn, Cu, N and Mg, and bioavailability of Zn and Fe (estimated by molar ratios of PA/Zn, PA × Ca/Zn, PA/Fe, or PA × Ca/Fe). Although concentrations of Zn and Fe were increased and Ca was decreased in treatments of half spikelets removal and spike shading, the simultaneously increased PA limited the increase in bioavailability of Zn and Fe. In general, different nutrient elements interact with each other and are affected to different degrees by source-sink manipulations. Elevated endogenous ABA levels and ABA/ACC ratios were associated with increased TKW and grain-filling of Zn, Mn, Ca and Mg, and inhibited K in wheat grains. However, effects of ACC were diametrically opposite. These results provide basis for wheat grain biofortification to alleviate human malnutrition.

Research has shown a protective association between social support and depression, depression among stroke patients, and health impacts of depression. Yet not much is known on the effect of social support on depression among stroke patients. This review aims to summarize the current research examining the association between social support and depression among stroke patients. A literature search was performed in PubMed to find original peer-reviewed journal articles from 2016 to Mar. 12, 2023 that examined the association between social support and depression among stroke patients. The search terms were depression and "social support" and stroke, which lead to 172 articles. After abstract review, seven observational studies that studied the target association among stroke patients were selected. One additional study was found using PsycINFO as a complementary source with the same search strategy and criteria. Overall, a negative association was found between social support and depression among stroke patients in seven studies, with more social support leading to lower rates of depression post-stroke. One study found that social support was positively related with depression, but the result was nonsignificant. Overall, the results of recent studies suggest that social support is negatively associated with depression among stroke patients. In most studies, this association was statistically significant. The findings suggest the importance of improving social support perceived by stroke patients in the prevention of depression after the occurrence of stroke.

A wealth of Full Waveform (FW) LiDAR data are available to the public from different sources, which is poised to boost the extensive application of FW LiDAR data. However, we lack a handy and open source tool that can be used by potential users for processing and analyzing FW LiDAR data. To this end, we introduce waveformlidar, an R package dedicated to FW LiDAR processing, analysis and visualization as a solution to the constraint. Specifically, this package provides several commonly used waveform processing methods such as Gaussian, adaptive Gaussian and Weibull decompositions, and deconvolution approaches (Gold and Richard-Lucy (RL)) with users’ customized settings. In addition, we also developed functions to derive commonly used waveform metrics for characterizing vegetation structure. Moreover, a new way to directly visualize FW LiDAR data is developed through converting waveforms into points to form the Hyper Point cloud (HPC), which can be easily adopted and subsequently analyzed with existing discrete-return LiDAR processing tools such as LAStools and FUSION. Basic explorations of the HPC such as 3D voxelization of the HPC and conversion from original waveforms to composite waveforms are also available in this package. All of these functions are developed based on small-footprint FW LiDAR data, but they can be easily transplanted to the large footprint FW LiDAR data such as Geoscience Laser Altimeter System (GLAS) and Global Ecosystem Dynamics Investigation (GEDI) data analysis. It is anticipated that these functions will facilitate the widespread use of FW LiDAR and be beneficial for better estimating biomass and characterizing vegetation structure at various scales. The package and code examples can be found at https://github.com/tankwin08/waveformlidar.

We propose a novel plasmon nano-optical antenna that consists of three vertically superimposed discs with different materials. Two symmetrical nanometer-scale Yagi antenna elements with gold-material are embedded into the surface of the middle disc with silicon dioxide. Based on plasmon theory and Yagi antenna principle, we explore the properties of the far-field radiation and near-field transmission of the antenna in near infrared band. It is found that the pattern of the xoy plane in the antenna can be adjusted in arbitrary direction. The far-field pattern and near-field transmission spectrum can be reconfigured by changing the angle a of the Yagi antenna elements in the middle disc. Moreover, we also discuss the influences of the widths and lengths of the elements on the near-field transmission spectrum when a is fixed at 0 degree.

This paper describes the formulations for viscoplasticity of metals based on the Chaboche and Delobelle model. The implementations of the viscoplastic models were detailed herein and then implemented via user subroutines for material models (UMAT) in ABAQUS. Two typical metals, i.e., 316 Stainless Steel and Zircaloy-4, were chosen as examples and their viscoplastic behaviors were captured. Numerical simulations are compared to reported experiments to validate the models and the UMAT codes. Typical viscoplastic behaviors of both metals, such as stress relaxation and creep, were captured well against available experiments. We publicize all the data and codes via: https://github.com/XJTU-Zhou-group/ABAQUS_UMAT_316ss_Zr4.

Current adaptive cruise control (ACC) systems adopt fixed desired time headway, which leads to an abrupt speed reduction after being cut-in by a lane changer in front or when changing lanes too close to the new leader. In contrast, human drivers behave differently and feature a variable spacing within 20 or 30 seconds right after a cut-in or lane change. Motivated by the smooth transition found in driver relaxation, the paper aims to incorporate relaxation into ACC systems. Based on the open-source ACC platform, Openpilot, Comma.ai, the paper proposes a feasible relaxation model compatible with current factory ACCs, which has also been tested using a market car with stock ACC hardware. The study further investigates the impact of relaxation ACC on traffic operation. Numerical simulation suggests that incorporating relaxation into ACC can help: i) reduce the magnitude of speed perturbations in both cut-in vehicles and followers; ii) stabilize the lane-changing traffic by reducing the speed variance and prevent the lateral propagation of congestion, and iii) increase the average vehicle speed and capacity in merging traffic.

Kombucha is a popular sparkling sugared tea, fermented by a symbiotic culture of acetic acid bacteria (AAB) and yeast. The demand for Kombucha is increasing worldwide mainly due to its perceived health benefits and appealing sensory properties. This study isolated and characterised the dominant AAB and yeast from starter culture and Kombucha broth after 0, 1, 3, 5, 7, 9, 11, and 14 days of fermentation at ambient temperature (~22°C). Changes in the microbial composition were associated with variations in the physico-chemical characteristics of Kombucha tea, such as pH, titratable acidity, and total soluble solids (TSS). During fermentation, the acidity increased, and TSS decreased. The yield, moisture content and water activity of the cellulosic pellicles which had developed by the end of fermentation were attributed to the presence of AAB. Yeast and AAB were isolated from the Kombucha samples using glucose yeast extract mannitol ethanol acetic acid (GYMEA) and yeast extract glucose chloramphenicol (YGC) media respectively, using serial dilutions. Phenotypic and taxonomic identification of AAB and yeast were determined by morphological and biochemical characterisation, followed by sequence analysis of the ribosomal RNA gene (16S rRNA for AAB and ITS for yeast). The dominant AAB species in the cellulosic pellicle and Kombucha broth was identified as Komagataeibacter rhaeticus. The yeast isolates belonged to Debaryomyces prosopidis and Zygosaccharomyces lentus.

In this paper, thin plate theory and moderately thick plate theory are proposed for analyzing the bending problem of rectangular plates with stepped thickness resting on elastic half-space foundation. The ground reaction is considered as an unknown coefficient and the hypothesis of Winkler foundation model and two-parameter ground model is eliminated in this method, so as to obtain the law of internal force distribution of the plate and the distribution law of contact reaction force between the stepped rectangular plate and foundation. The stepped rectangular plate is divided into upper and lower plates, and thin plate theory and moderately thick plate theory are used to obtain the analytical solution. The obtained analytical solutions in this paper are compared with results reported in other publications to verify the accuracy of this method. The effects of the elastic modulus and dimensions of the plate, and theory of plate are also considered. The analytical solutions show that it is feasible to decompose the stepped rectangular plate into two plates for analyzing the bending properties of stepped rectangular plate, and this method provide a reference for the study of multilayer stepped rectangular plates.

(1) Background: Heat stress detrimentally restricted the economic in dairy farming production, therefore, this study was designed to investigate how automatic spraying method on alleviating heat stress on cows. (2) Methods: A total of 1208 multiparous dairy cows were randomly allocated into 6 barns, three barns were equipped with automatic sprinklers (SP), each barn was considered as a replicate. The other three barns were considered as control treatments (CON). Each barn was considered as a replicate. (3) Results: body temperature and milk somatic cell count were significantly decreased, while DMI, milk yield, and milk fat content significantly increased with spraying treatment. ICR was improved from 30% to 35%. Rumen fermentation was enhanced by the increased levels of total VFA, acetate, propionate, and butyrate with the spraying treatment. Rumen microbiota results showed at the phylum level, rumen Fibrobacters abundance significantly increased by the spraying treatment. At the genus level, Eubacterium, Shuttleworthia, Saccharofermentans, Lachnospira, Pseudobutyrivibrio, Selenomonas, and Succinivibrio abundance were significantly increased, while Ruminococcaceae and Rikenellaceae abundance were significantly decreased in the rumen with spraying treatment. (4) Conclusion: this study demonstrated automatic spraying modulated the rumen microbiota composition and fermentation function, and effectively meliorated side-effects of heat stress on dairy cows.

Brain metastasis (BrM), involving the spread of cells from a primary tumor through the blood circulation system to the brain microvasculature, eventually progresses despite multiple treatments and remains a substantial contributor to major mortality in patients with advanced- stage cancer. Molecular signatures and immune cellular components of the tumor microenvironment (TME) are emerging as essential regulators involved in establishing an organ-specific metastasis (colonization) and therapeutic response. A comprehensive understanding of detailed characterization and the immune landscape in context of process of BrM formation will greatly expand the horizon of treatments available to target these deadly diseases. In this review, we provide a comprehensive picture of the complex interactions between tumor cells and immune cellular components participated in the BrM process. Based on this knowledge, we will discuss opportunities and challenges for therapeutic strategies against BrM.

The pathogen Cryptococcus neoformans is a major cause of fungal meningitis in humans. As with other melanotic microorganisms associated with human diseases, the cell wall-associated melanin of C. neoformans is a major virulence factor that contributes to its ability to evade host immune responses. The levels of melanin substrate and the regulation of melanin formation could be influenced by the microbiota-gut-brain axis. Moreover, recent studies show that C. neoformans infection causes dysbiosis in the human gut microbiome. In this review, we discuss the potential association between cryptococcal meningitis and the gut microbiome. Additionally, we emphasize the promising prospects of targeting the gut microbiome as a means of diagnosing and treating this debilitating disease.

Additive manufacturing (AM) provides customization of the microstructure and mechanical properties of components. Selective laser melting (SLM) is the commonly used technique for processing high strength Aluminum alloys. Selection of SLM process parameters could control the microstructure of fabricated parts and their mechanical properties. However, process parameter limits and defects inside the as-built parts present obstacles to customized part production. This study is the second part of a comprehensive work that investigates the influence of SLM process parameters on the quality of as-built Al6061 and AlSi10Mg parts. The microstructure of both materials was characterized for different parts processed over a wide range of SLM process parameters. The optimized SLM parameters were investigated to eliminate the internal microstructure defects. Mechanical properties of the parts were illustrated by regression models generated with design of experiment (DOE) analysis. The results reported in this study were compared to previous studies, illustrating how the process parameters and powder characteristics could affect the quality of produced parts.

In this study, 10%PTFE/PEEK blend were modified by potassium titanate whisker (PTW) and chopped glass fiber (GF), respectively. The blends were prepared by three-screw extruder. Through the investigation of thermal stability, tribological properties, mechanical properties and rheological behavior, the effects of reinforcing agents were determined. The results illustrated that the mechanical properties of 10%PTFE/PEEK blend can be dramatically improved by adding reinforcing agent of PTW or GF, and the reinforcing effect of GF was especially obvious. As for tribological properties, 1% addition was the best proportion. The friction coefficient and wear rate of the blend with 1% PTW were 0.283 and 4.97 × 10^-6 mm³/N · m, which decreased by 7.2% and 21% compared with those of the blend without reinforcing agent.

Structural health monitoring has been studied by a number of researchers as well as various industries to keep up with the increasing demand for preventive maintenance routines. This work presents a novel method for reconstruct prompt, informed strain/stress responses at the hot spots of the structures based on strain measurements at remote locations. The structural responses measured from usage monitoring system at available locations are decomposed into modal responses using empirical mode decomposition. Transformation equations based on finite element modeling are derived to extrapolate the modal responses from the measured locations to critical locations where direct sensor measurements are not available. Then, two numerical examples (a two-span beam and a 19956-degree of freedom simplified airfoil) are used to demonstrate the overall reconstruction method. Finally, the present work investigates the effectiveness and accuracy of the method through a set of experiments conducted on an aluminium alloy cantilever beam commonly used in air vehicle and spacecraft. The experiments collect the vibration strain signals of the beam via optical fiber sensors. Reconstruction results are compared with theoretical solutions and a detailed error analysis is also provided.