This study aims to exploit the distinctive properties of carbon nanotube materials, which are particularly pronounced at the microscopic scale, by deploying fabrication techniques that allow their features to be observed macroscopically. Specifically, we aim to create a semiconductor device that exhibits flexibility and the ability to modulate its electromagnetic wave absorption frequency by means of biasing. Initially, we fabricate a sheet of carbon nanotubes through a vacuum filtration process. Subsequently, phosphorus and boron elements are separately doped into the nanotube sheet, enabling it to embody the characteristics of a PN diode. Measurements indicate that, in addition to the fundamental diode's current-voltage relationship, the device also demonstrates intriguing transmission properties under the TEM mode of electromagnetic waves. It exhibits a frequency shift of approximately 2.3125 GHz for each volt of bias change. The final result is a lightweight and flexible carbon-based semiconductor microwave filter, which can conform to curved surfaces. This feat underscores the potential of such materials for innovative and effective electromagnetic wave manipulation.

In the context of the coordinated development of digital economy and environmental protection, we take the strategy of "Broadband China" as a quasi-natural experiment, adopts the panel data of 284 cities from 2007 to 2020, and evaluates the policy effect of digital economy on total factor energy efficiency through the progressive DID model. The results show that: The construction of "Broadband China" demonstration city has significantly promoted the improvement of the total factor energy efficiency of the demonstration city, but there is also significant urban heterogeneity, which is manifested in the significant improvement of the total factor energy efficiency of the eastern city, the southern city, the big city and the non-resource-based city. It has no significant effect on the total factor energy efficiency of central and western cities, northern cities, small and medium-sized cities and resource-based cities. The construction of "Broadband China" demonstration cities can improve total factor energy efficiency by promoting technological progress and strengthening environmental regulations. Therefore, we should further strengthen the construction of digital infrastructure and give full play to its positive effects. Different cities should seek differentiated development paths based on their own resource endowments and development conditions, so that the digital economy can effectively improve the total factor energy efficiency.

In this paper, we present a novel Two-Echelon Ground Vehicle and Its Mounted Unmanned Aerial Vehicle Cooperated Routing Problem (2E-GUCRP). The 2E-GUCRP arises in the field of Unmanned Aerial Vehicle (UAV) Routing Problem such as those encountered in the context of city logistics. In a typical cooperated system, the UAV is launched from the Ground Vehicle (GV) and automatically flies to the designated target. Meanwhile, acting as a mobile base station, the GV can charge or change the UAV’s battery on the designated landing points to enable the UAV to continue its mission. The objective is to design efficient GV and UAV routes to minimize the total mission time while meeting the operational constraints. A Mixed Integer Programming (MIP) model, which could be solved by commercial software, is constructed to describe this problem. In order to quickly solve the medium-scale problems, two existing heuristics to solve 2E-VRP are improved. The computational experiments are set up to compare our model with the 2E-VRP. The results indicate that the 2E-GUCRP obtains a better efficiency. Further discussion of the practical instance points out that the increase in efficiency is related to the speed relationship between the GV and the UAV.

This paper first discusses a fractional-order Liu system of order as low as 2.7 and shows its chaotic characteristics by carrying out numerical simulations such as Lyapunov exponents, bifurcation diagrams and phase portraits. Then, by using the topological horseshoe theory and computer-assisted proof, the existence of chaos in the system is verified theoretically. Finally, the fractional-order system is implemented on a Field Programmable Gate Array (FPGA) and the results obtained show that the fractional-order Liu system is indeed chaotic.

The location routing problem of unmanned aerial vehicles (UAV) in border patrol for intelligence, surveillance and reconnaissance is investigated, where the location of UAV base stations and the UAV flying routes for visiting the targets in border area are jointly optimized. The capacity of the base station and the endurance of the UAV are considered. A binary integer programming model is developed to formulate the problem, and two heuristic algorithms combined with local search strategies are designed for solving the problem. The experiment design for simulating the distribution of stations and targets in border is proposed for generating random test instances. Also, an example based on the Sino-Vietnamese border is presented to illustrate the problem and the solution approach. The performance of the two algorithms are analyzed and compared through randomly generated instances.

A new variant of two-echelon routing problem is investigated, where the truck and the drone are used to cooperatively complete the deliveries of all parcels. The truck not only acts as a tool for parcel delivery, but also serves as a moving depot for the drone. The drone can carry several parcels and take off from the truck, while returning to the truck after completing the delivery. The energy consumption model for the routing process of the drone is analyzed, when it is utilized to deliver multiple parcels. A two-stage route-based modelling approach is proposed to optimize both the truck’s main route and the drone’s adjoint flying routes. A hybrid heuristic integrating nearest neighbor and cost saving strategies is developed to quickly construct a feasible solution. The simulated annealing algorithm is applied to improve the quality of the solution, where a Tabu list is employed to improve the search efficiency. Random instances at different scales are used to test the performance of the proposed algorithm. A case study based on the practical road network in Changsha, China, is presented, through which the sensitivity analysis is conducted with respect to some critical factors.

A novel high-voltage powerline inspection system is investigated, which consists of the cooperated ground vehicle and drone. The ground vehicle acts as a mobile platform that can launch and recycle the drone, while the drone can fly over the powerline for inspection within limited endurance. This inspection system enables the drone to inspect powerline networks in a very large area. Both vehicle’ route in the road network and drone’s routes along the powerline network have to be optimized for improving the inspection efficiency, which generates a new two-layer point-arc routing problem. Two constructive heuristics are designed based on “Cluster First, Rank Second” and “Rank First, Split Second”. Then local search strategies are developed to further improve the quality of the solution. To test the performance of the proposed algorithms, practical cases with different-scale are designed based on the road network and powerline network of Ji’an, China. Sensitivity analysis on the parameters related with the drone’s inspection speed and battery capacity is conducted. Computational results indicate that technical improvement on the inspection sensor is more important for the cooperated ground vehicle and drone system.

The effects of climate change on yield and quality for different climate regions had high uncertainty. Risk assessment is an effective measure to assess the seriousness of the projected impacts for decision-makers. The modified quality model was used to simulate integrated impacts of climate change, environment and management on wheat yield and quality. Then, the Canadian Earth System Model (CanESM2) was used to forecast the daily meteorological data, and Statistical Down Scaling Model was used for downscaling. CERES-Wheat was combined with the forecasted meteorological data to simulate the future wheat yield and grain protein concentration (GPC). The risk of wheat yield and quality in three climatic regions of Shaanxi combined with two climate change scenarios of CanESM2 were assessed. Temperature increased 0.22-3.34 °C and precipitation increased 10-60 mm for RCP4.5 and RCP8.5. Elevated temperature and precipitation had positive effects on yield in all regions. The yield risk of most regions with climate change decreased 3.8%-25.1%. The GPC risk of all regions with climate change decreased 7.3%-27.2%. Irrigation decreased yield risk greatly in all regions, while had totally different effects for the three climatic regions. Yield risk with irrigation decreased 37.7%-52.1% in different climate. In contrast to previous studies, GPC risk with irrigation increased greatly 25.8%-28.9% in humid region, 3.9%-8.8% in sub-humid region, and decreased 37.7%-52.1% in semi-arid region. Climate change decreased yield risk and GPC risk together. While irrigation decreased yield risk greatly in all regions, had totally different effects for the three climatic regions.

A metering roundabout where traffic is controlled by traffic lights with phase times influenced by queue detector occupancy might be the solution to enhance performance when there are unbalanced traffic flows at roundabouts. There have, however, been minimal studies on how the distance of the queue detector from the stop line affects signal phase time durations and the queuing lengths. This research, therefore, seeks to develop a Cuckoo Search/Local search Algorithm using parameters such as arrival volumes, conflicting volumes, detector distance and phase time to investigate the relationship of signal setting, detector location and queuing formulations. Also, some additional statistical tests were performed for the fitness of the data. In order to conduct solid model validations, model output data was compared against the AIMSUN model. The results from the analyses demonstrated that the queue detector distance can affect phase time durations and vehicle queuing lengths on the controlling approach as well as queuing lengths on the metered approach. This study showed that, based on the study for the Old Belair Road roundabout in Adelaide, South Australia, the total queue length (controlling + metered) will be minimized when the detector is relocated at 209 meters from the roundabout stop line, giving longer phase green times and resulting in decreased intersection queuing lengths.

High-rise building fires pose a serious threat to the lives and property safety of the people. The lack of reliable and accurate positioning means is one of the main difficulties faced by rescue. In the absence of prior knowledge of the high-rise building fire environment, the coverage deployment of mobile base stations is a challenging problem that has not received much attention in the literature. This paper studies the problem of autonomous optimal deployment of base stations in high-rise building fire environment based on UAV group. A novel problem formulation is proposed that solves the non line of sight (NLOS) positioning problem in complex unknown environment. The purpose of this paper is to realize the coverage and deployment of mobile base stations in complex and unknown fire environment. The NLOS positioning problem in the fire field environment is turned into the line of sight (LOS) positioning problem through the optimization algorithm. And there are more than three LOS base stations nearby any point in the fire field. A control law which is formulated in a mathematically precise problem statement is developed that guarantees to meet mobile base stations deployment goal and to avoid collision. Finally, positioning accuracy of our method and that of common method were compared. The simulation result showed that the positioning accuracy of simulated firefighter in the fire field environment was improved greatly.

The advancement of mass spectrometry technologies has revolutionised plant metabolomics research by enabling the acquisition of raw metabolomics data. However, the identification, analysis, and visualisation of these data require specialised tools. Existing solutions lack a dedicated plant-specific metabolite database and pose usability challenges. To address these limitations, we developed PlantMetSuite, a web-based tool for comprehensive metabolomics analysis and visualisation. PlantMetSuite encompasses interactive bioinformatics tools and databases specifically tailored for plant metabolomics data, facilitating upstream-to-downstream analysis in metabolomics and supporting integrative multi-omics investigations. PlantMetSuite can be accessed directly through a user's browser without the need for installation or programming skills. The tool is freely available at https://plantmetsuite.verygenome.com/ and will undergo regular updates and expansions to incorporate additional libraries and newly published metabolomics analysis methods. The tool's significance lies in empowering researchers with an accessible and customisable platform for unlocking plant metabolomics insights.

Today, we are all threatened by an unprecedented pandemic: COVID-19. How different is it from other coronaviruses? Will it be attenuated or become more virulent? Which animals may be its original host? In this study, we analyzed 377 publicly available complete genome sequences for the COVID-19 virus, the previously known flu-causing coronaviruses (HCov-229E, HCov-OC43, HCov-NL63 and HCov-HKU1) and the lethal, pathogenic P3/P4 viruses, SARS, MERS, Victoria, Lassa, Yamagata, Ebola, and Dengue. We found strong similarities between the current circulating COVID-19 and SARS and MERS, as well as COVID-19 in rhinolophines and pangolins. On the contrary, COVID-19 shares little similarity with the flu-causing coronaviruses and the other P3/P4 viruses. Strikingly, we observed divergence of COVID-19 strains isolated from human hosts has steadily increased from December 2019 to March 2020, suggesting COVID-19 is actively evolving in human hosts. From all existing human COVID-19 genome sequences, we calculated the first common model that represents the shared sequences of the human COVID-19 strains, which provides important information for vaccine and antibody development. Geographic and time-course analysis of the evolutionary trees of the human COVID-19 reveals possibly heterogeneous evolutional paths among strains from 21 countries. This finding has important implications to the management of COVID-19 and the development of vaccines.

Vanadium is a well-known essential trace element, which usually exists in oxidation states in form of vanadate cation intracellularly. The pharmacological study of vanadium begins at the discovery of its unexpected inhibitory effect on ATPase. Thereafter, the protective effects on cells and the abilities in glucose metabolism regulation were observed from vanadium compound, leading to the application of vanadium compounds in clinical trials for curing diabetes. Alzheimer’s dis-ease (AD) is the most common dementia disease in elderly people. However, there is still no efficient agents for treating AD safely to date. This is mainly because of the complexity of the pathology, which are characterized by the senile plaques composed by amyloid-beta (Aβ) protein in the parenchyma of brain and the neurofibrillary tangles (NFTs) derived from hyperphosphorylated tau protein in neurocyte, along with mitochondrial damage, and eventually the central nervous system (CNS) atrophy. AD was also illustrated as type-3 diabetes, because of the observations of insulin deficiency and the high level of glucose in cerebrospinal fluid (CSF), as well as the im-paired insulin signaling in brain. In this review, we summarized the advance of applicating vanadium compound on AD treatment in experimental research and pointed out the limitation of the current study on using vanadium compounds in AD treatment. We hope it will help the future study in this field.

The statistical technique, the multiple regression model, is employed to analyze the relationship between the dependent variable and several independent variables. The multicollinearity problem is one of the assumptions in the multiple regression model that occurred in the relationship among independent variables. The ordinal least square is the standard method to evaluate parameters in the regression model, but the multicollinearity problem affects the unstable estimator. The Liu regression is proposed to approximate the Liu estimators based on the Liu parameter to overcome multicollinearity. For this paper, we have proposed the modified Liu parameter to estimate the biasing parameter in scaling options to compare the ordinal least square estimator with two modified Liu parameters and six standard Liu parameters. The performance of the modified Liu parameter is considered with the generating independent variables from the multivariate normal distribution in the Toeplitz correlation pattern as the multicollinearity data, where the dependent variable is obtained from the independent variable multiplied with a coefficient of regression and with the error from the normal distribution. The mean absolute percentage error is computed as an evaluation criterion of estimation. For application, the Hepatitis C patients dataset is a real dataset to investigate the benefit of the modified Liu parameter. Through the simulation and real dataset, it can be seen from the results that the modified Liu parameter outperforms the other Liu parameters and the ordinal least square estimator. It can recommend the user for estimating parameters by using the modified Liu parameter when the independent variable exits the multicollinearity problem.

The accuracy of sales prediction models based on the big data of online word-of-mouth (eWOM) is still not satisfied. We argue that eWOM contains heat and sentiments of different product dimensions, which can improve the accuracy of these models. In this paper, we propose a dynamic topic analysis (DTA) framework in order to extract heat and sentiments of product dimensions from the big data of eWOM. Finally, we propose an autoregressive-heat-sentiment (ARHS) model, which integrates heat and sentiments of dimensions into the baseline predictive model. The empirical study in movie industry confirms that heat and sentiments of dimensions can improve the accuracy of sales prediction model. ARHS model is better for movie box-office revenue prediction than other models.

Use of antibiotics and other chemicals to combat disease outbreaks have been a bottleneck for the sustainable growth of shrimp industry. Among various replacement proposed, organic acid (OA) and their salts (OS) are commonly used by farmers and feed millers. However, in free forms, their requirement is very high (2-3 kg/MT) as they tend to disassociate before reaching the hindgut. The dosage can be reduced by microencapsulation of the ingredients. In this study, a 63-day trial was conducted to assess the effects of OA and OS (COMP) microencapsulated (ENCAP) with fat (HF), fat + alginate (HA), wax esters – (WE), and HA and WE (HAWE) on performance, digestive enzyme, immune, and resistance to Vibrio parahaemolyticus. A positive control (PC, 200 g/kg fishmeal - FM) and a negative control (NC, 130 g/kg FM) diet were formulated. Eight other diets were formulated supplementing NC diet with microencapsulated OA (OAHF, OAHA, OAWE, OAHAWE) and OS (OSHF, OSHA, OSWE, OSHAWE). Among the ENCAPs, significant difference was observed in serum malondialdehyde (P = 0.026) where HF showed the lowest level (6.4 ±0.3 mmol/L). Significant interactions between COMP and ENCAP were observed in lipid deposition (P = 0.047), serum alkaline phosphatase and acid phosphatase (P < 0.0001), and hepatopancreatic and serum phenol oxidase (P < 0.0001). Despite no differences, 96-h mortality during pathogenic Vibrio parahaemolyticus challenge in all treatment diets (45% - 56%) was lower compared to the NC diets (63%). In conclusion, use of HF microencapsulated OA diets could provide improved performance and disease resistance that could contribute to the reduction of antibiotic use by the shrimp industry.

A fluorescent probe, N'-((3-methyl-5-oxo-1-phenyl-4, 5-dihydro-1H-pyrazol-4-yl) methylene)-2-oxo-2H-chromene-3-carbohydrazide (MPMC), was synthesized and characterized. Characterizations of the synthetic MPMC were conducted by proton nuclear magnetic resonance (1HNMR) spectroscopy and carbon-13 nuclear magnetic resonance spectroscopy (13C NMR). The fluorescence emission behaviors of probe MPMC towards diverse metal ions were detected and the probe exhibited high sensitivity and selectivity towards Cu2+ over other metal ions via quenching of its fluorescence. Furthermore, the existence of other metal actions made no difference on the fluorescence intensity of the MPMC-Cu2+ system apparently, that is, MPMC displayed a good anti-interference ability. Job’s plot of MPMC and copper ions indicated the detection limit was 15.16 nM (R2=0.9612) for the assayed actions, with a stoichiometric ratio of 1:1 for MPMC and Cu2+. Additionally, the color of MPMC probe solution changed from nearly colorless to yellow in the presence of Cu2+ in visible light, which the color change could be observed by the naked eye. Similarly, the color resolved bright yellow into blue in ultraviolet light. Also reusability studies indicated that MPMC probe was reusable. The pH effect of probe MPMC to Cu2+ had a broad range of pH detection 4.0 to 11.0. The response time of MPMC probe for determining Cu2+ was within 1 min. The recognition of Cu2+ by MPMC performed on pre-treated paper under sunlight and UV light both had a distinct colour change. Thus, the solid-state method for detecting Cu2+ with the naked-eye, was both economical and convenient.

Adlay (Coix lachryma-jobi L. var. ma-yuen Stapf) contains various phytonutrients for treating many diseases in Asia. To investigate whether orally administered of adlay bran oil (ABO) can cause drug interactions, the effects of ABO on the pharmacokinetics of five cytochrome P450 (CYP) probe drugs were evaluated. Rats were given a single oral dose (2.5 mL/kg BW) of ABO 1 h before administration of a drug cocktail either orally or intravenously, and blood was collected at various time points. A single oral dose of ABO administration did not affect the pharmacokinetics of five probe drugs when given as a drug cocktail intravenously. However, ABO increased plasma theophylline, dextromethorphan, and diltiazem when co-administered an oral drug cocktail. After 7-days of feeding with an ABO-containing diet, plasma concentrations of theophylline and chlorzoxazone were increased after oral administration of drug cocktail. The major CYP enzyme activities in liver and intestinal were not affected by ABO treatment. Results from this study indicate that a single oral dose or short-term administration of ABO may increase plasma drug concentrations when ABO is given concomitantly with drugs. ABO is likely to enhance intestinal drug absorption. Therefore, caution is needed to avoid food-drug interactions between ABO and co-administered drugs.

Multicellular organisms organize themselves according to two principles; first, the equilibrium between the driving force of unstable state cells and apoptosis or senescence; and second, the mutual equilibrium between the functional requirements of different types of cells. For the first principle, we deduce that stem cells at different levels have their own growth limits, which are determined by two factors: the ability of the stem cells to enter an unstable state (specifically, the ability of cells to divide and differentiate); and the rate of cellular senescence, loss of function, and finally, apoptosis. The superposition of stem cell limits at different levels over each other can amplify small differences at the genetic level. Moreover, the growth limits of different organs are different, which lead to different individuals having completely different appearances. The second principle is that the sum of the specific output functions of an organ must be equal to the overall demand for the function to be provided by the organ. If negative entropy input can meet this equilibrium, defects in certain genes will cause these defective individuals to become larger or develop other morphology.

As the number of end-of-life vehicles continues to grow, the field of separation technology for broken copper and aluminium parts of end-of-life vehicles has emerged as a significant area of research. As a key technology for the separation of non-magnetic non-ferrous metals, such as copper and aluminium, eddy current separation can achieve efficient separation of non-magnetic non-ferrous metals according to their differing conductivity and density. Nevertheless, further research is required in the separation of large-scale broken copper and aluminium parts of end-of-life vehicles. This paper presents a novel magnetic roller model comprising circumferential and axial periodic arrangements of permanent magnets. A single permanent magnet was constructed as an equivalent current model, and the magnetic scalar potential equations were solved using simulation tools. This allowed the distribution of the magnetic field outside the magnetic roller to be studied. The results demonstrate that the novel permanent magnet array magnetic roller can enhance the magnetic field intensity and action distance of the external magnetic field, which is more conducive to the separation of large-scale broken copper and aluminium parts of scrap cars. The findings of this research provide a theoretical foundation for the separation of scrap car broken copper and aluminium parts.

Relapsed leukemia following initial therapeutic response and remission is difficult to treat and causes high patient mortality. Leukemia relapse is due to residual quiescent leukemia cells that escape conventional therapies and later reemerge. Eliminating not only growing but quiescent leukemia cells is critical to effectively treating leukemia and preventing its recurrence. Such therapeutic agents, however, are lacking in the clinic. Here we report that a 4-arylmethyl derivative of the natural anticancer compound curcumin demonstrates a dual effect in eliminating both growing and quiescent leukemia cells. This curcumin derivative, C212, on the one hand, inhibits growing leukemia cells at a higher efficacy than curcumin by inducing apoptosis and cell cycle arrest; it, on the other hand, kills quiescent leukemia cells that are resistant to conventional chemotherapy drugs. Furthermore, C212 drives leukemia cells into and kills them at deep quiescence, avoiding the potential risk associated with awaking therapy-resistant subpopulation of quiescent leukemia cells. Lastly, we show that C212 induces apoptosis and drives cells into deep dormancy at least partially by binding to and inhibiting Hsp90, leading to client protein degradation and protein aggregation. Further elucidating the molecular mechanisms underlying the dual function of C212 in eliminating both growing and quiescent leukemia cells will aid the development of novel therapies against leukemia relapse.

We propose a new approach of extending the laser filament plasma channel. By adding a circular aperture quartz plate before the focusing lens, the extension of the plasma channel is doubled. The effects of different diameters, thicknesses of the circular aperture quartz plate and different pulse energies on the length of the plasma channel were investigated. The experimental results show that the thickness of the quartz plate and the depth of the hole have little effects on the plasma channel of the filament, and the diameter of the hole in the center of the quartz plate has a significant effect on the length of the optical filament. The moving-focus model is used to explain the extension of the optical filament.

Heterosis plays a significant role in enhancing variety, boosting yield, and raising economic value, but the molecular mechanism is still unclear. We analyzed the transcriptomes and 3D genomes of hybrid (F1) and its parents (w30 and 082). Analysis of the expression revealed a total of 485 specially expressed genes (SEGs), 173 differentially expressed genes (DEGs) above parental expression level, more actively expressed genes and up-regulated DEGs in F1. Further study revealed that the DEGs detected in F1 and its parents were mainly involved in response to auxin, plant hormone signal transduction, DNA metabolic process, Purine metabolism, starch and sucrose metabolism, which suggested that these biological processes may play a crucial role in the heterosis of B. rapa. The analysis of 3D genome data revealed that hybrid F1 tend to contain more transcriptionally active A compartments after hybridization. Additionally, F1 had a smaller TAD (topologically associated domain) genome length, but the number was the highest, and the expression change of activated TAD was higher than repressed TAD. More specific TAD boundaries were detected between parents and F1. Subsequently, 140 DEGs with genomic structural variants were selected as potential candidate genes. Among them, we found two DEGs with consistent expression changes in A/B compartments and TADs. Our findings suggest that genomic structural variants, such as TADs and A/B compartments, may affect gene expression and contribute to heterosis in B. rapa. This study provides further insight into the molecular mechanism of heterosis in B. rapa.

The ANFC/ABPE-10 composite film was prepared by ABPE-10 impregnating into ANFC films under negative pressure. And the composite film had meted high performance FOLED substrate requirement even when ANFC dosage was high for approximately 70%, which was consistent with for low cost efficiency, recyclability, and environmentally friendly. The enhanced properties of ANFC films were mainly because of the nature of ABPE-10 itself and the IPN structure formed between ABPE-10 and ANFC film. The transparency of composite films with different ANFC dosage was significantly increased from 67% to 88% by UV-Vis analysis. The composite film inherited the properties of AFNC, obtaining low CTE characteristics and ductile compact structure. The contact angles of ANFC films increased by 102% from 49.2° to 102.9°after dipping ABPE-10. Additionally, the composite films had outstanding mechanical properties such as tensile strength 173.72 MPa, Young’s modulus 4.06 GPa, and elongation at break 5.81%.

With the development of health service, animal husbandry, aquaculture and chemical industry, more and more pollutants are discharged into the water environment, including antibiotics and heavy metal ions. These hazard substances pose a great threat to environment safety and human health. As two kinds of new green solvents, ionic liquids (ILs) and deep eutectic solvents (DESs) are widely used in various fields including separation and environmental engineering, which are attracting huge attention from academia and industry. In this study, the optimal ionic liquid and deep eutectic solvent were selected and their complex with β-cyclodextrin (β-CD) were firstly prepared by simple and effective inclusion way. After necessary characterization and analysis, two kinds of complex were applied to prepare a special sorbent disc with two different sides by adding diluent (excipient) and pressing under 5~15 MPa. As the result, the IL and DES could be stably immobilized on the disc and play the key role in selective adsorption for targets. Besides that, the experiments of different hazardous substances achieved the expected results. Based on this study, the complex disc showed a lot of merits in the separation performance, easy preparation and use, simple operation, and good stability. It was believed to be a useful tool for water purification and detection.

Saline soil from the coast is a valuable resource that is readily available. It is also a valuable resource for reserving arable land. It has been demonstrated that adding organic fertilizers to salinized soils can effectively enhance them. However, since the improvement of saline soils cannot be achieved by a single measure, the effects of compound measures of organic fertilizers combined with mineral elements, humic acid, are significant and might be examined in depth. In order to explore the effects of various measures on the features of pH, electrical conductivity (EC), and nutrient changes in coastal salinized soils in Yancheng, Jiangsu Province, a ryegrass-alfalfa rotation with organic fertilizer as well as compound measures was designed. The findings indicated that the total nitrogen (TN) content of the soil increased and that all organic fertilizer composites decreased the electrical conductivity of the surface soil. However, the organic fertilizer with microbial fertilizer and humic acid was especially effective at regulating the pH and electrical conductivity of the surface soil during the time when salts were prone to accumulating. In conclusion, our findings point to new approaches to lowering salinity and boosting fertility in coastal saline soils: organic fertilizer with microbial fertilizers and humic acid, as well as organic fertilizer with Attapulgite clay.

Digital-Radio-Frequency-Memory (DRFM) has emerged as an advanced technique to achieve diverse jamming signals, due to its capability of intercepting waveforms within a short time. Multiple-Input Multiple-Output (MIMO) radars can transmit agile orthogonal waveform sets for different pulses to combat the DRFM-based jamming, where any two groups of waveform sets are also orthogonal. In order to design multiple groups of orthogonal waveform sets at the same time, this article formulates a group orthogonal waveforms optimal design model, whose objec-tive function is the weighted sum of the intra- and inter-group orthogonal performances metrics. To solve this optimization problem, this article proposes a group orthogonal waveforms design algorithm. Based on a primal-dual type method and proper relaxations, the proposed algorithm transforms the original problem into a series of simple sub-problems. Numerical results demonstrate that the proposed algorithm has the ability to balance the intra- and inter-group orthogonal performances by adjusting the weighting factors, which is not available using other state-of-the-art orthogonal waveform design algorithms.

Autonomous target recognition (ATR) plays a crucial role in maintaining situational awareness during environmental monitoring. Unmanned aerial vehicles (UAVs) equipped with autonomous target recognition technology can gather and analyze real-time information about targets, including their locations, sizes, and types. However, UAV-captured images in complex real-world environments often display significant variations in perspective and scale due to changes in UAV altitude and distance. Existing methods for autonomous target recognition on UAVs struggle to capture targets from large field-of-view and multi-scale images, resulting in low recognition accuracy and high false-positive rates. This paper introduces two novel Slimmable neural network models, namely SE-YOLOv5s and ST-YOLOv5s, which are based on the YOLOv5s architecture. These models incorporate the Squeeze and Excitation and Swin-Transformer mechanisms to enhance the ability to extract features from large field-of-view and multi-scale images. To evaluate their performance, experiments were conducted on the Visdrone19 aerial dataset. Compared to the state-of-the-art YOLOv5s algorithm, the utilization of SE-YOLOv5s and ST-YOLOv5s for autonomous target recognition on low-altitude drones resulted in improvements in both accuracy and false-positive rates. These proposed methods combine Slimmable neural network design with feature enhancement mechanisms, addressing the challenges posed by complex real-world environments in UAV missions. The advancements in autonomous target recognition on low-altitude drones will significantly contribute to enhancing situational awareness in future environmental monitoring.

The surface electromyogram (sEMG)--based gesture recognition to the development of intelligent prostheses has emerged as a promising avenue for upper limb amputees. However, the temporal variations in sEMG have rendered recognition models less efficient than anticipated. Cross-session calibration and training data indicate the capacity to reduce this variation. The impact of varying calibration and training data amounts on gesture recognition performance for amputees is still unknown. To assess these effects, we present four datasets for the evaluation of calibration data and examine the impact of training data volume on benchmark performance. Two amputees who had undergone amputations years prior were recruited and seven sessions of data were collected for analysis from each of them. The experimental results show that the calibration data improved the average accuracy per subject by 3.03% and 6.16%, respectively, compared to the baseline results. Moreover, it was found that to collect training data for modeling, boosting the number of training sessions proves more efficient than increasing the number of trials within a single session. Two potentially effective strategies are proposed in light of this research to enhance the cross-session models further. We consider these findings to be of the utmost importance for the commercialization of intelligent prostheses, as they demonstrate the criticality of gathering calibration and cross-session training data, as well as offer effective strategies for maximizing the utilization of the entire dataset.

(1) Background: Bacterial reinfection and root fracture are the main culprits related to root canal treatment failure. This study aimed to assess the utility of quercetin solution as an adjunctive endodontic irrigant that strengthen root canal dentin with commitment anti-biofilm activity and bio-safety. (2) Methods: Based on a noninvasive dentin infection model, dentin tubules infected with Enterococcus faecalis (E. faecalis) were irrigated with sterile water (control group), and 0, 1, 2, 4 wt% quercetin-containing ethanol solutions. The live and dead bacteria proportions within E. fae-calis biofilms were analyzed using confocal laser scanning microscopy (CLSM). Elastic modulus and hydroxyproline release and X-ray photoelectron spectroscopy (XPS) characterization was tested on irrigant-treated demineralized dentin to evaluate irrigants’ biostability. The cytotoxicity of irrigants was tested by CCK-8 assay. (3) Results: Quercetin increased the proportion of dead bacteria volumes within E. faecalis, and improved the flexural strength of dentin collagen com-pared to control group. The XPS characterization revealed an increase in C-O peak area under both C1s and O1s narrow-scan spectra. The CCK-8 assay confirmed no cytotoxicity of quercetin solutions. (4) Conclusions: Quercetin exhibited anti-biofilm activity, collagen-stabilizing effect as well as cytocompatibility, supporting quercetin as a potential candidate for endodontic irrigant.

Background: Estrogen homeostasis is crucial for bladder function, and estrogen deprivation resulting from ovarian removal or ovarian dysfunction may lead to various bladder dysfunctions. However, the specific mechanisms are not fully understood. Methods: We simulated estrogen deprivation using a rat ovariectomy model and supplemented estrogen through subcutaneous injections. The metabolic characteristics of bladder tissue were analyzed using non-targeted metabolomics, followed by bioinformatics analysis to preliminarily reveal the association between estrogen deprivation and bladder function. Results: We successfully established a rat model with estrogen deprivation and, through multivariate analysis and validation, identified several promising biomarkers represented by 3, 5-tetradecadiencarnitine, lysoPC (15:0), and cortisol. Furthermore, we explored estrogen deprivation-related metabolic changes in the bladder primarily characterized by amino acid metabolism imbalance. Conclusions: This study, for the first time, depicted the metabolic profile of bladder resulting from estrogen deprivation, providing an important experimental basis for future research on bladder dysfunctions caused by estrogen deprivation.

The integration of deep neural networks into sparse Synthetic Aperture Radar (SAR) imaging has been explored to enhance SAR imaging performance and reduce the system’s sampling rate. However, the scarcity of training samples and mismatches between the training data and the SAR system pose significant challenges to the method’s further development. In this paper, we propose a novel SAR imaging approach based on Deep Image Prior Powered by RED (DeepRED), enabling unsupervised SAR imaging without the need for additional training data. Initially, DeepRED is introduced as the regularization technique within the sparse SAR imaging model. Subsequently, variable splitting and the Alternating Direction Method of Multipliers (ADMM) are employed to solve the imaging model, alternately updating the magnitude and phase of the SAR image. Additionally, the SAR echo simulation operator is utilized as an observation model to enhance computational efficiency. Through simulations and real data experiments, we demonstrate that our method maintains imaging quality and system downsampling rate on par with deep neural network-based sparse SAR imaging, but without the requirement for training data.

This study presents application of demand response strategy in a standalone wind-solar-battery hybrid energy system (HES). Inputs for the designed HES are wind speed, solar radiation, temperature and load demand which is variable with time. In this study, hourly values of meteorological data and hourly load demand are considered in one year. An improved gravitational search algorithm (IGSA) is used to optimize the configuration of the standalone wind-solar-battery hybrid power system. The optimal objectives of the system are cost of the system in life cycle, the loss of power supply probability（LPSP）and the energy excess percentage（EXC）.The effect of demand response on economic benefit and energy storage allocation of the standalone wind-solar-battery system is studied. The obtained optimal configuration of the proposed HES can provide minimal energy cost with excellent performance and reduced waste and unmet load.

Pollution caused by copper is one of the key factors of environment contamination. As one of heavy metals, copper is hard to decompose in nature, the biological enrichment of which may lead to severe damage to health. Cu²⁺ detection, thus, possesses a bright application prospect both in environment protection and in human health. In this paper, a dual-functional fluorescence-magnetic composite nano-platform has been designed to sensitively detect, meanwhile capture and remove Cu²⁺ in the solution of water and ethanol (1:1, v/v). The core-shell structure nanoparticle synthesized by using Fe₃O₄ as core and SiO₂ as shell, is covalently bonded with rhodamine derivatives on the silica layer to construct the nano-platform. The emission is increased upon the addition of Cu²⁺, showing fluorescence turn on effect for the detection, and the limit of detection which was as low as 1.68 nM. Meanwhile, Cu²⁺ ions are captured by the coordination with rhodamine derivatives, and can be removable with the help of magnetic field.

The dual-station Interferometric Synthetic Aperture Radar (InSAR) system can overcome the physical limitations imposed by the baseline of single-station dual-antenna InSAR. It provides greater flexibility and can enhance elevation measurement accuracy through a well-designed baseline configuration.Unmanned aerial vehicles (UAV) equipped with dual-station InSAR, with relatively low cost and high flexibility, are useful for mapping and land resource exploration. However, due to challenges including spatiotemporal synchronization and motion errors, there are limited reports on UAV-borne dual-station InSAR. This paper proposes a comprehensive method for processing data from small UAV-borne dual-station InSAR by integrating two-way synchronization chain signals. The proposed method includes compensation for time and phase synchronization errors, trajectory refinement with synchronized chain and Position and Orientation System (POS) data, high-precision dual-station InSAR imaging and interferometric processing. Height inversion results based on the proposed method is also provided, demonstrating the effectiveness of the proposed method and improving interferometric accuracy at calibration points from 0.66 meters to 0.42 meters.

In order to realize rapid and nondestructive monitoring of wheat biomass in field, field experiments based on different densities, nitrogen fertilizer and variety treatments were studied. RGB images of wheat in the main growth stage were obtained by UAV, and wheat color and texture feature indices were obtained by image processing, and wheat biomass was obtained by field sampling in the same period. Then the relationship between different color and texture feature indices and wheat biomass was analyzed to select the color and texture feature index suitable for wheat biomass estimation. The results showed that there was a high correlation between image color index and wheat biomass in different stages, and most of them reached a very significant correlation level. However, the correlation between image texture feature index and wheat biomass was poor, only a few indexes reached significant or extremely significant correlation level. Based on the above results, the color indices with the highest correlation to wheat biomass or the combining indices of color and texture feature in different growth stage were used to construct estimation model of wheat biomass. The models were validated using independently measured biomass data, and the correlation between simulated and measured values reached the significant level, RMSE were smaller. This indicated that the estimated results by the models were reliable and accurate. It also showed that the estimation models of wheat biomass combined with color and texture feature indices of UAV image were better than the single color index models. The results would provide a new method for real-time monitoring of wheat field growth and biomass estimation.

Drought stress severely affects the normal growth and development of wheat, leading to reduced yields and quality. To address the lag and limitations of traditional drought monitoring methods, this paper proposes a drought stress monitoring model for winter wheat during critical growth stages based on deep learning. By acquiring drought stress images of winter wheat during three critical growth stages: rise-jointing, heading-flowering and flowering-maturity, a dataset correlating these images with soil moisture monitoring data was established. The DenseNet121 network model was selected as the base network to extract phenotypic features of winter wheat under drought stress. Variables such as the model's training approach, changes in learning rate, and whether an attention mechanism was included, were used to conduct eight sets of model training and optimization strategy experiments. A drought stress monitoring model for winter wheat during critical growth stages based on an improved DenseNet-121 was constructed. The results showed that the average recognition accuracy of the eighth group in the test set reached 94.67%, indicating good application prospects in the recognition of drought stress levels during critical growth stages of wheat.

Natural cellulose hydrogels have been widely used to enhance mechanical properties. However, existing natural fiber composite hydrogels are not reusable, limiting their potential applications. To address this issue, we designed and prepared a polyvinyl alcohol/glycerol /bamboo microfibril double network tough hydrogel using a simple method. The bamboo microfibril and polyvinyl alcohol form a tight and rigid network through hydrogen bonding, improving mechanical properties. The prepared polyvinyl alcohol/glycerol/bamboo microfibril double network tough hydrogel has the advantages of reusability and fatigue resistance. Furthermore, both the elastic modulus and toughness of the hydrogel increase with increasing bamboo microfibril content. We also demonstrated that the hydrogel can be recast after cyclic compression, maintaining its recyclability, stability, and certain stiffness and toughness. Our study highlights the potential of hydrogels for controllable mechanical properties, fatigue resistance and shows that polyvinyl alcohol/glycerol/bamboo microfibril hydrogel has broad value for plasticity and reuse.

The color changes corresponding to chromophore structures in lignin caused by exposure of Eucalyptus（Eucalyptus grandis and E. urophylla）to heat were investigated. Eucalyptus wood samples were heated in saturated steam atmospheres for 10 h at 110℃, 130℃, and 150℃. The lignin was isolated before and after heat treatment. The physicochemical properties of the lignin and changes in chromophore structures during heat treatment was evaluated through wet chemical analysis, FTIR, UV-Vis, GPC, XPSand 13C-NMR. The color of the wood became darker and redder with the increase in pressure and temperature. Depolymerization and dehydration reactions occurred via demethoxylation with heat treatment in saturated steam at 110℃ or 130℃. Lignin condensed to form insoluble compounds after heat treatment in saturated steam at 150℃. G units increased and S units decreased through demethylation during heat treatment, as revealed by FTIR and 13C-NMR analysis.

The lactic acid bacteria Streptococcus thermophilus and Lactobacillus helveticus are commonly used as starter cultures in dairy product production. This study aimed to investigate the characteristics of fermented milk using different ratios of these strains and analyze the changes in volatile compounds during fermentation and storage. The 10:1 ratio of Streptococcus thermophilus CICC 6063 to Lactobacillus helveticus CICC 6064 showed optimal fermentation time (4.2 h), viable cell count (9.64 log10 colony-forming units/mL), and sensory evaluation score (79.1 points). In total, 56 volatile compounds were identified and quantified by solid-phase microextraction and gas chromatography–mass spectrometry (SPME-GC-MS), including aldehydes, ketones, acids, alcohols, esters, and others. Among these, acetaldehyde, 2,3-butanedione, 2,3-pentanedione, 2-heptanone, acetoin, and 1-heptanol had the highest odor activity values and contributed to the characteristic flavor of fermented milk. The concentrations and types of key flavor compounds reached their peak at the end of fermentation. Throughout the fermentation and storage process, the levels of 2,3-pentanedione and acetoin exhibited synergistic dynamics. These findings enhance our understanding of the chemical and molecular characteristics of milk fermented with Streptococcus thermophilus and Lactobacillus helveticus, providing a basis for improving the flavor and odor of dairy products during fermentation and storage.

To investigate whether the ech42 gene in Clonostachys rosea can improve the biocontrol efficacy of Bacillus amyloliquefaciens and its molecular mechanism.Compared to the wild type, the B. amyloliquefaciens transformed with the ech42 gene exhibited a higher chitinase activity. The B. amyloliquefaciens-ech42 also showed a significantly higher biocontrol efficiency against B. cinerea when tomato plants were pre-treated with amyloliquefaciens-ech42. No significant difference of control efficiency was observed between the wild type and amyloliquefaciens-ech42 when tomato plants were first infected by B. cinerea. In addition, the activity of the defense-related enzyme polyphenol oxidase, but not superoxide dismutase was significantly higher in amyloliquefaciens-ech42 than in the wild type.The ech42 enhances the Bacillus amyloliquefaciens biocontrol efficiency by increasing the capacity of protection/prevention to plants, rather treating/killing the pathogens.

The Paeonia suffruticosa, called as 'Feng Dan', has been used for thousands of years in traditional Chinese medicine. In our chemical investigation on the root bark of the plant, five new phenolic dimers, namely paeobenzofuranone A‒E (1‒5), have been characterized. Their structures were determined by spectroscopic analysis including 1D and 2D NMR, HRESIMS, UV, and IR, as well as ECD calculations. Compounds 2, 4, and 5 showed cytotoxicity against three human cancer cell lines with IC50 values ranging from 6.7 to 25.1 μM. Compounds 1 and 2 showed certain inhibitory activity on NO production. To the best of our knowledge, the benzofuranone dimers and their cytotoxicity of P. suffruticosa are reported for the first time.

14-Deoxy-11,12-didehydroandrographolide (deAND), a diterpenoid in Andrographis paniculata (Burm. f.) Nees, acts as a bioactive phytonutrient that can treat many diseases. To investigate the protective effects of deAND on reducing fatty liver disease, male mice were fed a high-fat and high-cholesterol (HFHC) diet without or with 0.05% and 0.1% deAND supplementation. Cholesterol accumulation, antioxidant and anti-inflammatory activities in liver and liver injury were evaluated after deAND treatment. The results show that deAND treatment for 7 weeks reduced plasma alanine aminotransferase activity and lowered hepatic cholesterol accumulation, tumor nuclear factor-α, and histological lesions. 0.1% deAND treatment reduced HFHC diet-induced apoptosis by lowering the caspase 3/pro-caspase 3 ratio. After 11-weeks of deAND treatment, increased NOD-like receptor protein 3 (NLRP3), capase-1, and interleukin-1β protein levels in liver were suppressed by deAND treatment. In addition, nuclear factor erythroid 2-related factor 2 (Nrf2) mRNA expression, heme oxygenase-1 protein expression, and the activities of glutathione peroxidase and glutathione reductase were increased in mice fed the HFHC diet. However, those activities of antioxidant enzymes or proteins were also upregulated by 0.1% deAND treatment. Furthermore, deAND treatment tended to lower hepatic lipid peroxides. Finally, deAND treatment reversed the depletion of hepatic glutamate level induced by HFHC diet. These results indicate that deAND may ameliorate HFHC diet-induced steatohepatitis and liver injury by increasing antioxidant and anti-inflammatory activities.

As one of the main equipment of coal transportation, the belt conveyor with detection system is an important direction for the development of intelligent mine. The occurrences of non-coal foreign objects making contact with belts are common phenomenon in complex production environments and improper human operations. In order to avoid major safety accidents caused by scratches, deviation and breakage of the belt, a foreign object detection method is proposed for belt conveyor in this work. Firstly, a foreign object image dataset is collected and established, and IAT image enhancement module and attention mechanism of CBAM are proposed to enhance image data sample. Moreover, to predict the angle information of foreign objects with large aspect ratios, a rotating decoupling head is designed, and a MO-YOLOX network structure is constructed. Some experiments are carried out with the belt conveyor in the mine intelligent mining equipment laboratory, and the detections of different foreign objects are analyzed. Experimental results show that the accuracy, recall, and mAP50 of the proposed rotating frame foreign object detection method reaches 93.87%, 93.69%, and 93.72%, and the average inference time of foreign object detection is 25 ms.

Malaxidinae is one of the confusing groups with classification in Orchidaceae. Previous phylogenetic analysis reveals that the relationships among the taxa in Malaxidinae have not yet been reliably established using a few plastome regions or nuclear ribosomal internal transcribed spacer (nrITS). In the present study, the complete plastomes of Oberonia integerrima and Crepidium purpureum were assembled using high-throughput sequencing. Combined with publicly available complete plastome data, this resulted in a data set of 19 plastomes, including 17 species of Malaxidinae. The plastome feature and phylogenetic relationship were compared and analyzed. The results showed that: (1) The plastomes of Malaxidinae species possessed the quadripartite structure of typical angiosperms, with sizes ranging from 142,996 bp to 158,787 bp and encoding from 125 to 133 genes. The ndh genes were lost or pseudogenized with varying degrees in six species. An unusal inversion was detected in the Large Single-Copy region (LSC) of Oberonioides microtatantha. (2) A total of 8 regions, including ycf1, matK, rps16, rpl32, ccsA-ndhD, clpP-psbB, trn-FGAA-ndhJ, and trnSGCU-trnGUCC, were identified as mutational hotspots. (3) Based on complete plastomes, 68 protein-coding genes and 51 intergenic regions, respectively, the phylogenetic analyses resolved genera-level relationships in this subtribe with strong support. The Liparis was supported as polyphyletic.

In an effort to enhance the efficiency and safety of open-pit mines, this study explores the optimization of end slope road parameters and slope structures, specifically focusing on unmanned driving lanes.A significant aspect of the study is the development of a truck trajectory offset model, which considers the different reaction times between automated sensors and human drivers in adapting to environmental changes. To test these concepts, the study uses numerical simulations to confirm the stability of the proposed end slope designs. Using Victory West Mine No. 1 as a case study, the research determines the optimized width for unmanned driving lanes and the maximum angle for safe steepening of end slopes. The findings indicate that the optimized unmanned lane width for NTE240 mining dump trucks is 1743 mm, allowing for a 2-degree increase in the slope angle at the south end slope. This optimization leads to a steep mining stripping volume of 3.2735 million m³ and a coal output of 2.49628 million tons, maintaining a stripping ratio of 1.31m³/t. These results demonstrate that the unmanned driving road width optimization not only ensures slope safety but also significantly boosts the economic benefits of steep mining in open-pit mines.

To investigate the impact of electrode structure on Electrical Stimulation Therapy (EST) for chronic wound healing, this study designed three variants of flexible microelectrodes (FMs) with Ag-Cu coverings (ACCs), each exhibiting distinct geometrical configurations: hexagonal, cross-shaped, and serpentine. These were integrated with PPY@PDA/PANI (3/6) hydrogel dressings. Comprehensive animal studies, coupled with detailed electrical and mechanical modeling and simulations, were conducted to assess their performance. Results indicated that the serpentine-shaped FM outperformed its counterparts in terms of flexibility and safety, exhibiting minimal thermal effects and a reduced risk of burns. Notably, FMs with metal coverings under 3% demonstrated promising potential for optoelectronic self-powering capabilities. Additionally, simulation data highlighted the significant influence of hydrogel non-uniformity on the distribution of electrical properties across the skin surface, providing critical insights for optimizing EST protocols when employing hydrogel dressings.

Infectious keratitis (IK) represents a major cause of corneal blindness. This study aims to investigate the demographics, risk factors, microbiological characteristics and antibiotic susceptibility patterns of IK in Taiwan over the past 15 years. A retrospective population-based study was conducted using the Chang Gung Research Database. Patients with IK were identified by diagnostic codes for corneal ulcer from 2004 to 2019. Of 7807 included subjects, 45.2% of patients had positive corneal cultures. The proportion of contact lens-related IK declined, while that of IK related to systemic diseases grew. The percentage of isolated gram-positive bacteria surpassed that of gram-negative bacteria in the 15-year period. The prevalence of Pseudomonas aeruginosa showed a decreasing trend (p = 0.004), whereas coagulase-negative Staphylococcus (CNS) and Propionibacterium species were increasingly detected (p &lt; 0.001). Overall, the trend of antibiotic susceptibility of both gram-positive and gram-negative bacteria did not change throughout the study period. The susceptibility to the test antibiotics maintained over 90% in gram-negative isolates during 15 years. Vancomycin preserved 100% susceptibility to all gram-positive isolates. Since most tested antibiotics exhibited stable susceptibility over decades, this study reinforced that fluoroquinolones and fortified vancomycin continue to be good empiric therapies for treating bacterial keratitis in Taiwan.

(1) Background: in the context of sustainable development goals (SDGs), this work explores the repair direction of future cultivated land protection policies based on the Smith policy implementation model from the historical evolution to ensure that the cultivated land protection policy does not deviate during the implementation process. (2) Methods: this paper uses literature research and inductive deduction methods to sort out the evolution process of Chinese cultivated land protection policy, summarize the successful experience of transferring the focus of cultivated land protection in chronological order, and conclude the repair direction of Chinese cultivated land protection. (3) Results: although the Chinese cultivated land protection policy in the historical evolution has through three significant phases, there are still certain issues in the development trend of Chinese cultivated land protection policy based on regional division of labor for grain transportation and sales. (4) Conclusion: directly utilizing feedback from farmers as stakeholders will contribute to the maturity and improvement of cultivated land protection policies in the specific implementation of cultivated land protection policies.

The total ionizing dose (TID) effect significantly impacts the electrical parameters of fully depleted silicon on insulator (FDSOI) devices and even invalidates the on-off function of devices. At present, most of the irradiation research on the circuit level is focused on the single event effect, and the research on the total ionizing dose effect is very little. Therefore, this study mainly analyzes the influence of TID effects on a CMOS inverter circuit based on 22 nm FDSOI transistors. First, we constructed and calibrated an N-type FDSOI metal-oxide semiconductor (NMOS) structure and P-type FDSOI metal-oxide semiconductor (PMOS) structure. The transfer characteristics and trapped charge distribution of these devices were studied under different irradiation doses. Next, we studied the TID effect on an inverter circuit composed of these two MOS transistors. The simulation results show that when the radiation dose is 400 krad (Si), the logic threshold drift of the inverter is approximately 0.052 V. These results help further investigate the impact on integrated circuits in the irradiation environment.

Flour yield determined the profitability of flour mill, but the intrinsic variability of the grain makes it very complex to analysis and estimate wheat grain flour yield. Simulation for flour yield attributes offer considerable advantages in flour mill, if reliable predictions of flour yield can be provided, because the wheat grain characteristics can be tested before milling. If this is possible, the characteristics thus observed could be quantified more reliably and objectively by Structural Equation Modelling (SEM). SEM was used to look for the most important wheat grain characteristics on flour yield, and then these wheat grain characteristics were used to simulate flour yield. Furthermore, the regressive equation was verified by the field experiment. The coefficient of variation of grain characteristics was low and distributed rather closely. The results of SEM showed that test weight had the most significantly effects on flour yield, followed by the hardness index. Test weight and hardness index could excellently estimate flour yield by multiplicative effect of test weight and hardness index, and which could determine 68% of the variation in flour yield. The simulation result can not only predict flour yield, but also look for the important grain characteristics for the flour yield.

Glycosaminoglycans (GAGs) with unique structures from marine animals show intriguing pharmacological activities and negligible biological risks, providing more options for us to explore safer agents. Swim bladder is a tonic food and folk medicine, and its GAGs show good anticoag-ulant activity. In this study, two GAGs SJG-1.0 and GMG-1.0 have been extracted and isolated from the swim bladder of Sphyraena jello and Gadus morhua. The physicochemical properties, pre-cise structural characteristics, and anticoagulant activities of these GAGs were determined. The analysis results of the SJG-1.0 and GMG-1.0 showed that they were chondroitin sulfate (CS)/dermatan sulfate (DS) hybrid chains with molecular weights of 109.32 kDa and 123.13 kDa, respectively. They were mainly composed of the repeating disaccharide unit of -{IdoA-α1,3-GalNAc4S-β1,4-}- (DS-A). The DS-B disaccharide unit of -{IdoA2S-α1,3-GalNAc4S-β1,4-}- also existed in both SJG-1.0 and GMG-1.0. SJG-1.0 had a higher proportion of CS-O disaccharide unit -{-GlcA-β1,3-GalNAc-β1,4-}-, while GMG-1.0 contained higher proportion of CS-E disaccha-ride unit -{-GlcA-β1,3-GalNAc4S6S-β1,4-}-. The disaccharide compositions of the GAGs varied in a species-specific manner. Anticoagulant activity assay revealed that both SJG-1.0 and GMG-1.0 had potent anticoagulant activity, which can significantly prolong activated partial thrombosis time. GMG-1.0 also can prolong the thrombin time. SJG-1.0 showed no intrinsic tenase inhibition ac-tivity, while GMG-1.0 can obviously inhibit intrinsic tenase with EC50 of 58 nM. Their significantly different anticoagulant activities may be due to their different disaccharide structural units and proportions. These findings suggested that the swim bladder CS/DS hybrid chains with well-defined structure may be safer anticoagulants with low bleeding risk.

Bulbophyllum is one of the largest genera and presents some of the most intricate taxonomic problems in the family Orchidaceae, including species of ornamental and medical importance. The lack of knowledge regarding the characterization of Bulbophyllum chloroplast (cp) genomes has imposed current limitations on our study. Here, we reported the complete cp genomes of seven Bulbophyllum species, including B. ambrosia, B. crassipes, B. farreri, B. hamatum, B. shanicum, B. triste and B. violaceolabellum, and compared with related taxa to provide a better understanding of their genomic information on taxonomy and phylogeny. A total of 28 Bulbophyllum cp genomes exhibit typical quadripartite structures with lengths ranging from 145,092 bp to 165,812 bp and GC content of 36.60% to 38.04%. Each genome contained 125–132 genes, encompassing 74–86 protein-coding genes, 38 tRNA genes, and eight rRNA genes. The genome arrangements, gene contents and length were similar with differences observed in ndh gene composition. A total of 18–49 long repeats and 38–80 simple sequence repeats (SSRs) were detected and the single-nucleotide (A/T) was dominant in Bulbophyllum cp genomes, with an obvious A/T preference. An analysis of relative synonymous codon usage (RSCU) revealed Leucine (Leu) was the most frequently used codon, while cysteine (Cys) was the least used. Six highly variable regions including ndhF-trnLUAG, trnTUGU-trnLUAA, trnFGAA-ndhJ, rps15-trnNGUU, rbcL-accD and psbI-trnSGCU were identified based on the ranking of the Pi values, had the potential to serve as DNA markers for species identification and phylogeny of the genus Bulbophyllum. Phylogenetic analysis based on the complete cp genome sequences and 68 protein-coding genes strongly supported 28 Bulbophyllum species can be divided into four branches and sects. Brachyantha, Cirrhopetalum, Leopardinae defined by morphology were non-monophyly. Our results enriched the genetic resources of Bulbophyllum species, providing valuable information to illustrate the complicated taxonomy, phylogeny and evolution process of the genus.

A real-time two-way direct load control (TWDLC) of central air-conditioning chillers in wide area is proposed to provide demand response. The proposed TWDLC scheme is designed to optimize the load shedding ratio of every customer under control to ensure the target load to be shed is met at every scheduling period. In order to overcome the load reduction uncertainties of TWDLC, an innovative solution is proposed by applying a certain degree of loosening on the constraint of the actual shed load. Fuzzy linear programming is utilized to solve the optimization problem with fuzzy constraints. The proposed fuzzy linear programming problem is solved by delicately transforming it into a regular liner programming problem. A selection scheme used to obtain the feasible candidates set for load shedding at every sampling interval of TWDLC is also designed along with the fuzzy linear programming.

We study the electron tunneling (ET) and local Andreev reflection (AR) processes in a quantum dot (QD) coupled to the left and right ferromagnetic leads with noncollinear ferromagnetisms. In particular, we consider that the QD is also side-coupled to a nanowire hosting Majorana bound states (MBSs) at its ends. Our results show that when one mode of the MBSs is coupled simultaneously to both spin-up and spin-down electrons on the QD, the height of the central peak is quite different from that if the MBS is coupled to only one spin component electrons. The ET and AR conductances which are mediated by the dot-MBS hybridization strongly depend on the angle between the left and right magnetic moments in the leads, which result in sign change of the angle-dependent tunnel magnetic resistance. This result is very different from case when the QD is coupled to regular fermonic mode, and can be used for detecting the existence of MBSs, a current challenge in condensed matter physics under extensive investigations.

Camouflage is a natural or artificially process to prevent an object from being detected while camouflage breaking is a countering process for the identification of the concealed object. We report that a perfectly camouflaged object in a two-dimensional scene can be retrieved and detected with stereo-vision assisted three-dimensional (3D) imaging perceived with stereopsis. The analysis is based on binocular energy model applied to general 3D settings. We show that a perfectly concealed object with random noise background can be retrieved with vision’s stereoacuity to resolve the hidden structures. The theoretical analysis is further tested and demonstrated with distant natural images taken by a drone-camera, processed with a computer and displayed in an autostereoscopy. The recovered imaging is presented with removal of the background interference to demonstrate the general applicability for camouflage breaking with stereo imaging and sensing.

Multi-wire saw machining (MWSM) used for slicing hard-brittle materials in semiconductor, is an important material removal process that uses free abrasives. Cutting model of single-wire saw machining (SWSM) is the basis of MWSM, and the material removal mechanism of SWSM can better understand than MWSM. Mathematical model (includes brittle fracture and plastic deformation) is presented in this paper for SWSM ceramic with abrasives. This paper determines the effect of various machining parameters on the removal of hard-brittle materials. For brittle fracture of SWSM ceramics, the minimum of the strain energy density is used as a fracture criterion. The material removed of SWSM ceramics due to plastic deformation is calculated using the equations of motion. Actual wire-sawing experiments are conducted to verify the results from the developed mathematical model. Theoretical results agree with experimental data and practical experience. The developed mathematical model shows that brittle fracture plays a major concern role in material removed of SWSM ceramics. Wire speed and working load have positively correlated with material removed of SWSM ceramics. The coefficient of friction is low, a lateral crack, which propagates almost parallel to the working surface, leads to more brittle fracture and material removed is increased on SWSM ceramics.

To achieve a micro-destructive and rapid measurement of the wood density of standing trees, this study investigated the feasibility of using the micro-drilling resistance method, formulated a mathematical model, explored the potential for a unified model across multiple tree species, and analyzed the influence of moisture content on measurement accuracy. First, 231 tree cores and drill resistance data were sampled from Pinus massoniana, Cunninghamia lanceolate, and Cryptomeria fortunei. The basic density and moisture content of each core were measured, and the average value of each resistance data record was calculated. Second, the average drill resistance, the natural logarithm of average drill resistance, and absolute moisture content were used as independent variables, while the wood basic density was used as the dependent variable. Third, the total model of the three tree species and sub-model for each tree species were established through a stepwise regression method. Finally, the accuracy of each model was compared and analyzed with that of using the average basic density of each tree species as an estimated density. The results revealed that the estimation accuracy of the sub-model for each tree species was 1.670 percentage points higher than the average value of each tree species used as the density estimation value for these tree species. Additionally, except for Cryptomeria fortunei, the natural logarithm of drill resistance significantly influenced the wood density model at a significance level of 0.05. Moreover, moisture content significantly affected the total model and sub-models of Pinus massoniana at a significance level of 0.05. The estimation accuracy of the total mathematical model was 2.125 percentage points lower than that achieved using the average basic density of each tree species to predict their density. The results indicated the feasibility of using the micro-drilling resistance method to measure the wood density of standing trees. Moreover, the relationship between wood density and drill resistance did not follow a linear pattern, and moisture content slightly influenced the drill needle resistance. Furthermore, the establishment of a mathematical model for each tree species was deemed essential. This study provides valuable guidance for measuring the wood density of standing trees through the micro-drilling resistance method.

IoT is a computational perception that defines a situation, where smart objects are interconnected to the internet/ network. In the last few years, IoT objects have increased in all sectors/ fields and use in all domains of our lives. As the number of devices increases, the privacy of data becomes an important issue. To deal with this issue different techniques have been used by researchers in this field. Unfortunately, these methods have less traceability, privacy of data, and accountability. This paper aims to design a blockchain-based network architecture for Traceability, Data privacy, and Accountability (TDA). Technologies of blockchain are known as a distributed ledger of transactions record, which record the life span information with a timestamp. The major features of blockchain are persistency, decentralization, and audibility. These features help to decrease the budget and increase efficiency. Moreover, to strengthen the TDA architecture, this paper also discusses the performance of the proposed architecture.

Three new cembranoids (1–3) and a new casbanoid (4), along with three known analogues (5–7), have been isolated from the soft coral Sinularia nanolobata collected off Ximao Island. The structures including the absolute configurations of new compounds were established by extensive spectro-scopic data analysis, time-dependent density functional theory/electronic circular dichroism (TDDFT-ECD) calculations and the comparison with spectroscopic data of known compounds. In in vitro bioassay, compounds 1 and 5 exhibited moderate cytotoxic activities against human erythroleukemia (HEL) cells line with IC50 values of 37.1 and 42.4 uM, respectively.

Thyroid nodules (TNs) are common thyroid lesions in older population. Few studies focused on the prevalence of TNs and its relationship to lifestyle characteristics and dietary habits in centenarians. The current study aimed to determine the prevalence of TNs in Chinese centenarians using high-resolution ultrasound equipment and investigate its relationship to lifestyles and dietary habits. The current study was part of China Hainan Centenarian Cohort Study (CHCCS) which conducted in Hainan, an iodine sufficient region in China. A total of 874 permanent residents aged 100 years or older (mean age, 102.8 ± 2.8 years) without any missing data were included in the analysis. Among the participants, 649 of them were detected at least one thyroid nodule under the ultrasound examinations. The overall prevalence rate of TNs was 74.3%. The prevalence of TNs was higher in participants who were females, hypertension, diabetes, and underweight than their counterparts. Multivariate logistic regression analyses showed that being female, hypertension, diabetes, betel quid consumption, red meat consumption were independent risk factors, while being underweight, and nut consumption were independent protective factors for TNs. Our findings indicate that the presence of thyroid nodules was highly prevalent in Chinese centenarians, particularly in females. In addition to gender, hypertension, diabetes, and underweight, the presence of TNs was independently associated with betel quid, red meat, and nut consumptions. Further prospective studies are warranted to verify these associations in population from different age strata, races, cultures, and iodine backgrounds.

Keywords: Porcine reproductive and respiratory syndrome virus, baculovirus surface display vectors, neutralizing antibody, IFN-γ, IL-4.

In this paper, four lithological parameters, i.e. thermal conductivity, particle size, porosity and saturation, are investigated by combining experimental observations with numerical simulations to study the influence laws and mechanisms of action on the combustion process of methane hydrate sediments. The variation of combustion characteristics parameters such as flame height, effective combustion ratio and dimensionless discharge water mass with the lithological parameters are studied. In addition, the combustion mechanism of lithologic parameters on methane hydrate deposits is revealed. Combining the experimental results and simulation calculations, to optimize the combustion of methane hydrate sediments, it is recommended to use methane hydrate sediment samples with high saturation and low thermal conductivity, while the oxidant concentration and porosity of methane hydrate sediment samples should be increased.

Objectives. Invasive fungal spondylodiscitis (IFSD) is rare and could be lethal in certain circumstances. Previous literature revealed limited data concerning the outcomes. This study aimed to establish a risk-scoring system. Methods. A total of 53 patients were included in the study from a multi-centered database in Taiwan. All the clinicopathological and laboratory data were retrospectively analyzed. Variables strongly related to 1-year mortality were identified using a multivariate Cox proportional hazards model. A receiver operating characteristic curve was used to express the performance of our IFSD scoring model. Results. Five strong predictors were included in the IFSD score: predisposing immunocompromised state, the initial presentation of either radiculopathy or myelopathy, initial laboratory findings of WBC > 12.0 or < 0.4 103/uL, hemoglobin < 8 g/dL, and evidence of candidemia. 1-year mortality rates for patients with IFSD Scores of 0, 1, 2, 3, and 4 were 0%, 16.7%, 56.3%, 72.7%, and 100%, respectively. The area under the curve of the receiver operating characteristic curve was 0.823. Conclusions. We developed a practical scoring model with easily obtained demographic, clinical, and laboratory parameters to predict the probability of 1-year mortality in patients with IFSD. However, more large-scale and international validations would be necessary before this scoring model is commonly used.

Silicon has been proved to be one of the most promising anode materials for the next generation of lithium-ion battery. For the application in batteries, Si anode should have high capacity and must be industrially scalable. In this study, we have designed and synthesised a hollow structure to meet these requirements. All the processes are carried out without special equipment. The Si nanoparticles that are commercially available are used as the core sealed inside TiO₂ shell, with rationally designed void space between the particles and shell. The Si@TiO₂ are characterised using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and scanning electron microscope (SEM). The optimised hollow structured silicon nanoparticles, when used as anode in lithium-ion battery, exhibit a high reversible specific capacity over 600 mAhg-1. This excellent electrochemical property of the nanoparticles can be attributed to their optimised phase and unique hollow nanostructure.

In this paper, a novel permanent magnet-assisted synchronous reluctance machine (PMASynRM) with rare-earth PMs and ferrite magnets is proposed. The performance of PMASynRM is discussed with respected to the different magnet ratio of rare-earth PMs and ferrite magnets. Some characteristics including the flux density, output torque, cogging torque, output power, power factor, torque ripple, loss, efficiency, and demagnetization are calculated by 2-D finite element analysis (FEA). The analysis results show that the excellent performance can be obtained by using hybrid magnet of rare-earth PMs and ferrite magnets with the suitable magnet ratio, and provide some desirable cost-performance trade-off.

This manuscript proposes a novel tangent-graph-based method that provides all distinctive topology paths, as a set of trajectories that can not be transformed into each other by gradual bending and stretching without colliding with obstacles. As the global optimal trajectory (limited by dynamic constraints) may not correspond to the shortest path (almost without dynamic constraints), it is important to provide all distinctive topology paths rather than just the globally shortest one. One of the application is provide initial paths for trajectory planning methods, such as time elastic band (TEB) and dynamic window approach (DWA). Considering that a mobile platform is always working in a dynamic changing environment and that update the whole graph is time consuming, a dynamic rectify method is proposed to update tangents according to local map provided by sensor reading. Finally, results under real grid maps are presented.

Path planning in 3D environment is a fundamental research area for robots and autonomous vehicles. Based on the principle ``the shortest path consists of tangents'', RimJump* is proposed as a tangent-based path planning method suitable for finding the shortest path (both off-ground and on-ground) in 3D space (e.g., octomap and point cloud) for mobile platform to follow. RimJump* searches the tangent graph in the form of a path tree and considers the geometrical properties of the locally shortest path. Therefore, the method can provide all of the locally shortest paths that connect the starting point and the target, including the globally shortest path. And the time cost of RimJump* is insensitive to map scale increases in comparison to methods that search the whole passable space rather than the surface of the obstacle, e.g., Dijkstra and A*. In the Results, RimJump* is compared with other methods in terms of path length and time cost.

The theory of the continuous two-dimensional (2D) Fourier Transform in polar coordinates has been recently developed but no discrete counterpart exists to date. In the first part of this two-paper series, we proposed and evaluated the theory of the 2D discrete Fourier Transform (DFT) in polar coordinates. The theory of the actual manipulated quantities was shown, including the standard set of shift, modulation, multiplication, and convolution rules. In this second part of the series, we address the computational aspects of the 2D DFT in polar coordinates. Specifically, we demonstrate how the decomposition of the 2D DFT as a DFT, Discrete Hankel Transform (DHT) and inverse DFT sequence can be exploited for efficient code. We also demonstrate how the proposed 2D DFT can be used to approximate the continuous forward and inverse Fourier transform in polar coordinates in the same manner that the 1D DFT can be used to approximate its continuous counterpart.

The rapid advancement of technology has led to increased electronic consumption and a corresponding rise in e-waste generation. To address this issue, this study develops a low-carbon e-commerce closed-loop supply chain (LCE-CLSC) system with remanufacturer, platform, and the government as key stakeholders. An evolutionary game approach is employed to investigate the system's dynamics, analyzing the impact of stakeholder strategies on system equilibrium. Numerical simulations reveal important findings: Firstly, government initiatives promoting recycling, carbon taxes on traditional products, can incentivize remanufacturers to produce low-carbon items and encourage platform investment in recycling services. Secondly, higher sales revenues motivate remanufacturers to produce low-carbon products. Thirdly, consumer sensitivity to recycling services strengthens waste recovery when platforms increase investments in these services, leading to remanufacturers choosing low-carbon production. Lastly, government subsidies may become ineffective if the cost of remanufacturers' carbon reduction and platforms' recycling services exceeds their affordability. These findings offer insights for the sustainable development of obsolete electronic product recycling systems.

To understand the molecular mechanism underlying yellowing in pineapples during ripening, coupled with alterations in fruit quality, comprehensive metabolome and transcriptome investigations were carried out. These investigations were conducted using the pulp samples collected at three distinct stages of maturity: young fruit (YF), mature fruit (MF), and fully mature fruit (FMF). This study revealed a noteworthy increase in the levels of total phenols and flavones, coupled with a concurrent decline in lignin and total acid content, as the fruit transitioned from YF to FMF. Furthermore, the analysis yielded 167 differentially accumulated metabolites (DAMs) and 2194 differentially expressed genes (DEGs). Kyoto Encyclopedia of Genes and Genomes enrichment analysis based on DAMs and DEGs revealed that the biosynthesis of plant secondary metabolites, particularly the flavonol, flavonoid, and phenypropanoid pathways, plays a pivotal role in fruit yellowing. Additionally, a comprehensive regulatory network encompassing genes that contribute to metabolisms of flavones, flavonols, lignin, and organic acids was proposed. This network sheds light on the intricate processes that underlies fruit yellowing and quality alterations. These findings enhance our understanding of the regulatory pathways governing pineapple ripening and offer valuable scientific insight into the molecular breeding of pineapples.

Excretory-secretory products (ESPs) are the main research targets for investigating the hosts and helminths interaction. Parasitic worms can migrate to parasitic sites and avoid the host immune response by secreting this product. Angiostrongylus cantonensisis an important food-borne zoonotic parasite that causes severe neuropathological damage and symptoms, including eosinophilic meningitis or meningoencephalitis in humans. Benzaldehydes are organic compounds composed of a benzene ring and formyl substituents. This compound has anti-inflammatory and antioxidation properties. Previous studies showed that 3-hydroxybenzaldehyde (3-HBA) and 4-hydroxybenzaldehyde (4-HBA) can reduce apoptosis in A. cantonensis ESPs treated astrocytes. These results on the protective effect underlying benzaldehyde have primarily focused on cell survival. The study was designed to investigate the molecular mechanisms of endoplasmic reticulum stress (ER stress) and oxidative stress in astrocytes in A. cantonensis ESPs treated astrocytes and to evaluate the therapeutic consequent of 3-HBA and 4-HBA. First, we initially established the RNA-seq dataset in each group, including Normal, ESPs, ESPs+3-HBA, and ESPs+4-HBA. We also found that benzaldehyde (3-HBA and 4-HBA) can stimulate astrocytes to express ER stress-related molecules after ESP treatment. The level of oxidative stress could also be decreased in astrocytes by elevating antioxidant activity and reducing ROS generation. These results suggested that benzaldehyde may be a potential therapeutic compound for human angiostrongyliasis to support brain cell survival by inducing the expression levels of ER stress- and oxidative stress-related pathway.

This study uses a mass-spring-damping system to simulate the repeated strain of liquefaction cyclic triaxial tests. The two results are compared in this paper to understand the feasibility of the mass-spring-damping system developed in this paper and the feasibility of future research on this related topic and development potential. The main factors affecting this mode's repeated strain are the spring coefficient k and the external force Q0. The spring coefficient has an inverse relationship but does not increase in multiples. The external force has a direct proportional relationship but does not increase the result- a non-multiple increase. When the pore water pressure of the liquefied cyclic triaxial test specimen rises, it will cause the specimen to liquefy, decreasing effective stress, shear modulus G, and damping ratio D, causing an increase in strain. The shear modulus and damping ratio are related to the spring coefficients k and c. Both are variables that change with time. This article takes an original thin-tube specimen at point A in the Yunlin area in Taiwan as a testing example. Through Mathematica software, it can be obtained that the mass m=1kg, the spring coefficient k=244e-0.1t kgf/cm, and the damping coefficient c=0.739e-0.257t kgf-s/cm and external force Q0=10.1sin2πt kg; Finally, this study selected the original thin-tube specimens from four locations in the Yunlin area, and simulated the repeated strain amount of the cyclic triaxial test specimens through a spring-damping system. The results show that the spring-damping system is feasible for simulated cyclic triaxial tests because the model is simple and the parameters are easy to understand and obtain, which also shows the extensibility of this model. Preliminary results of the research show that this model can further simulate the repeated strain obtained by cyclic triaxial tests without considering the increased trend in pore water pressure and the decrease in effective stress during cyclic loading.

Developing and utilising of underground space is an vital direction for urban growth. Underground commercial streets, as a significant component of underground space accommodating extensive human social activities, and consequently necessitate the creation of human-scale spaces. In the evolution of urban design development towards greater refinement, applying architectural theories and excessively subjective designs has resulted in a deficiency of human-centered design and a disordered spatial environment. This study merges environmental psychology and architectural theory to determine the appropriate length of spatial scale. Two experiments focusing on spatial perception evaluation were conducted using a virtual experimental platform that featured varying dimensions of spatial scale combinations. These quantified combinations were correlated with perception evaluation, and regression analysis was employed to identify appropriate scale ranges, which were superimposed on the range of length selection. Finally, the optimal length and scale combination for underground commercial street spaces were established, providing a reference for the human-centered design of these environments.

A new power receiving unit (PRU) is proposed in this paper for the resonant wireless power transfer (WPT), which is characterized by the capability of attracting high power from the power transmitting unit (PTU). The resonant WPT is designed for delivering the electrical power to the PRU attached on an electrical vehicle (EV) chassis 50cm away from a PTU installed on the ground. The proposed PRU uses only the passive elements such as inductors, diodes and the capacitors, which needs no initial power from the EV. It is then applicable for charging a battery to several hundred volts for even a first-time charging battery. At a switching frequency of the resonant WPT in the experiment being 4MHz, the proposed PRU behaves itself as a negative impedance converter (NIC) in the subharmonics of 4MHz. The NIC effect plus the subharmonic oscillation causes an instability current charging the battery connected to the PRU. In this paper, we simulated the PRU and performed the experiment. The experiment demonstrates a battery charging of 150W from 50cm away using three D-mode GaN HEMT transistors via the instability current ramp. The power transfer efficiency (PTE) improved as the power delivered to load (PDL) goes higher. The best power transfer efficiency (PTE) is 65% in the present findings. The simulation analysis shows that the circuit allows itself be used to much higher power transfer when it is implemented with more GaN HEMT transistors connected in parallel. The theoretical derivation of the PRU circuit is also used to support both the experimental and simulation results.

In this study, the apparent variation range of acoustical parameters were investigated in a concert hall. The initial time delay gap (ITDG) was evaluated in terms of its just noticeable difference (JND) through two instruments, the cello and the trumpet. Even though the IDTG values were prolonged over the measurements and were not significantly varied, an ITDG range of 22 - 220 ms in increments of 91 steps was produced electro-acoustically in an anechoic chamber with a loudspeaker. The result of JNDc ((delta gap/gap) was rated 0.059 and 0.081 at 50% “different” judgement ranges for the cello and trumpet tracks, respectively. The effective duration of the autocorrection function (ACF) of the continuous brainwaves (CBWs) within the alpha (8-13 Hz) frequency range on the left hemisphere responding to 91-step ITDG increments revealed that the continuous ratio minimum Tauee e of CBW was approximately equal to 0.28 s on the trumpet. The continuous ratios of Tauee e_min ((Tauee e_min_rear - Tauee e_min_front)/ Tauee e_min_front) of CBWs were constantly at 0.4. Furthermore, a homologous period of resonance between the subjective JNDc and Tauee e values of the ACF of CBWs in the alpha range allowed us to conclude that the subjective JND of the ITDG in a room is related to the W_IACC value of the interaural cross-correlation function, which reflect the characteristics of source signal themselves and arouse the activities of brain on the right hemisphere (p < 0.01).

In the field of Natural Language Processing (NLP), Large Language Models (LLMs) have shown great potential in document-level event extraction tasks, but existing methods face challenges in the design of prompts. To address this issue, we propose an optimization strategy called "Definition-driven Document-level Event Extraction (DDEE)." By adjusting the length of the prompt and enhancing the clarity of heuristics, we have significantly improved the event extraction performance of LLMs. We used data balancing techniques to solve the long-tail effect problem, enhancing the model's generalization ability for event types. At the same time, we refined the prompt to ensure it is both concise and comprehensive, adapting to the sensitivity of LLMs to the style of prompts. In addition, the introduction of structured heuristic methods and strict limiting conditions has improved the precision of event and argument role extraction. These strategies not only solve the prompt engineering problems of LLMs in document-level event extraction but also promote the development of event extraction technology, providing new research perspectives for other tasks in the NLP field.

Rapid and accurate detection of road cracks is of great significance for road health monitoring, but currently this work is mainly completed through manual site surveys. Low-altitude UAV remote sensing can obtain images with centimeter or even subcentimeter ground resolution, which provides a new efficient and economical approach for rapid crack detection. Nevertheless, crack detection networks face challenges such as edge blurring and misidentification due to the heterogeneity of road cracks and the complexity of the background. To address these issues, we propose a real-time edge reconstruction crack detection network (ERNet) which adopts multi-level information aggregation to reconstruct crack edges and improve the accuracy of segmentation between the target and background. To capture global dependencies across spatial and channel levels, we propose an efficient bilateral decomposed convolutional attention module (BDAM) that combines depth separable convolution and dilated convolution to capture global dependencies across spatial and channel levels. To enhance the accuracy of crack detection, we use a coordinate-based fusion module that integrates spatial, semantic, and edge reconstruction information. In addition, we propose an automatic measurement of crack information for extracting the crack trunk and its corresponding length and width. Experimental results demonstrate that our network achieves the best balance between accuracy and inference speed.

Estimating the ocean’s subsurface thermohaline information from satellite measurements is essential for understanding ocean dynamics and El Niño phenomenon. This paper proposes an improved double-output Residual Neural Network (DO-ResNet) model to concurrently estimate the ocean subsurface temperature (OST) and ocean subsurface salinity (OSS) in the tropical Western Pacific using multi-source remote sensing data, including sea surface temperature (SST), sea surface salinity (SSS), sea surface height anomaly(SSHA), sea surface wind (SSW), and geographical information (including longitude (LON) and latitude (LAT)). In the model experiment, Argo data were used to train and validate the model, and the root mean square error (RMSE), normalized root mean square error (NRMSE) and coefficient of determination (R²) were employed to evaluate the model's performance. The results showed that the sea surface parameters selected in this study have a positive effect on the estimation process, and the average RMSE and R² values for estimating OST (OSS) by the proposed model are 0.34 °C (0.05 psu) and 0.91 (0.95), respectively. Under the data conditions considered in this study, DO-ResNet demonstrates superior performance relative to the extreme gradient boosting model, random forest model, and artificial neural network model. Additionally, this study evaluates the model’s accuracy by comparing its estimations of OST and OSS across different depths with Argo-derived data, demonstrating the model's ability to effectively capture the most spatial features, and by comparing NRMSE across different depths and seasons, the model displays strong seasonal adaptability. In conclusion, this research introduces a novel artificial intelligence technique for estimating OST and OSS in the tropical Western Pacific Ocean.

In order to cope with the challenges of physical and psychological aging in the indigenous people in Taiwan, most of the tribes in Taiwan set up cultural health stations for indigenous elderly. These community care facilities have practiced many health promotion activities, such as the reminiscence, life review, and arts activity. However, there was little exploration into the benefit of indigenous people’s practice the life review activity in Taiwan—the gap this study aimed to fill. This study adopts life review therapy through a set of innovative life review activity designs in indigenous older adults, including activity planning, and indigenous cultural elements. A qualitative study design using semi-structured interviews was used to obtain data from a purposive sample. Ten participants who assessed to the cultural health stations services and participated in the life review activities of the indigenous older adults in southern Taiwan were interviewed individually. The data were analyzed using Graneheim and Lundman’s qualitative content analysis. The theme—“experiences and benefits of participating”—and two categories with six subcategories emerged. The results demonstrated that the participation of the indigenous elderly in life review activities with cultural elements had obvious benefits for their mental health. Life review therapy can be incorporated as a supplementary LTC treatment for the indigenous people, thereby, promoting the positive emotions of the indigenous elderly.

Simple summary: The noninvasive differentiation of hepatocellular carcinoma (HCC) from intrahepatic cholangiocarcinoma (ICC) remains challenging. In recent years, the number of studies on the application of radiomics in liver cancer has grown dramatically. However, there have been very few studies on the differentiation of HCC from ICC based on multisequence magnetic resonance imaging (MRI) radiomics. This study aimed to investigate the efficacy of a radiomic model based on preoperative fat suppression T2-weighted imaging (FS-T2WI) and dynamic contrast-enhanced MRI features in the arterial phase (A) and portal venous phase (P) for the differentiation of HCC from ICC. Abstract: The purpose of this study was to investigate the efficacy of magnetic resonance imaging (MRI) radiomics in differentiating hepatocellular carcinoma (HCC) from intrahepatic cholangiocarcinoma (ICC). The clinical and MRI data of 129 pathologically confirmed HCC cases and 48 ICC cases from April 2016 to December 2021 at the Affiliated Hospital of North Sichuan Medical College were retrospectively analyzed. Included cases were randomly divided at a ratio of 7:3 into a training group of 124 cases (90 HCC cases and 34 ICC cases) and a validation group of 53 cases (39 HCC cases and 14 ICC cases). Radiomic features were extracted from axial fat-suppression T2-weighted imaging (FS-T2WI) and axial arterial-phase (A) and portal-venous-phase (P) dynamic contrast-enhanced MRI sequences, and the corresponding datasets were generated. The least absolute shrinkage and selection operator (LASSO) method was used to select the best radiomic features. Logistic regression was used to establish a radiomic model for each sequence (FS-T2WI, A, and P models) and a joint model (M model) integrating the radiomic features of all the sequences. The performance of each model was evaluated using the area under the receiver operating characteristic curve (AUC). The AUC of the FS-T2WI, A, P, and M models for distinguishing HCC from ICC was 0.693, 0.863, 0.818, and 0.914 in the training group and 0.690, 0.784, 0.727, and 0.802 in the validation group, respectively. The results of this study suggest that MRI-based radiomics may help noninvasively differentiate HCC from ICC. The model integrating the radiomic features of multiple sequences showed further improvement in performance.

Oxygen evolution reaction is a momentous part of electrochemical energy storage and conversion devices such as rechargeable metal-air batteries. It is particularly urgent to develop low-cost and efficient electrocatalysts for oxygen evolution reactions. As a potential substitute for noble metal electrocatalysts, transition metal selenides are still challenging in improving the activity of oxygen evolution reaction and the research of reaction intermediates. In this study, a simple one-step solvothermal method was used to prepare a polymetallic compound carbon matrix composite (Co9Se8/Ni3Se4/Fe3O4@C) with a multilayered nanosheets structure. It exhibited good OER activity in an alkaline electrolyte solution with an overpotential of 268 mV at 10 mA/cm2 in an alkaline medium. Besides, this catalyst also showed excellent performance in the 24 hours stability test. The composite presents a multi-layer sheet structure, which effectively improves the contact between the active site and the electrolyte. The selenide formed by Ni and Co has a synergistic effect, Fe3O4 and Co9Se8 form a heterojunction structure, which can effectively improve the reaction activity by initiating the electronic coupling effect through the interface modification. In addition, carbon quantum dots have rich heteroatoms and electron transferability, which improves the electrochemical properties of the composites. This work provides a new strategy for the preparation of highly efficient OER electrocatalysts utilizing the multimetal synergistic effect.

Practical applications of CsPbX3 nanocrystals (NCs) are limited by their poor stability. The formation of heterojunction between CsPbX3 NCs and oxides is an effective means to protect perovskite from polar solvents and other external factors. Significantly improving the stability and photocatalytic properties of the core/shell perovskite is very important for its application in photoelectric and photocatalytic technology. Here, we report the synthesis of asymmetrical CsPbBr3/TiO2 core-shell heterostructure NCs at single particle level by hot injection liquid phase synthesis and sol-gel method, where each CsPbBr3 NCs is partially covered by titanium dioxide. It is shown that the type II arrangement is generated at the heterogeneous interface, which greatly facilitates the separation of electron-hole pairs and increases the carrier transport efficiency. More crucial, due to the protection of titanium dioxide shell, the product has higher long-term stability in humid air compared with bare CsPbBr3 NCs. The asymmetrical core-shell heterostructure prepared in this study not only improves the stability of CsPbX3 NCs, but also provides some ideas for optoelectronic device applications and TiO2-based photocatalysts.

Reasonable allocation of production plans and saving the overall electricity cost are crucial for large manufacturing conglomerates, which is an effective way for conglomerates to realize open-source and cost-saving. This paper develops an optimization model of off-site industrial production scheduling for enterprises in response to the problems of high electricity costs due to the irrational allocation of production schedules on the demand side of China's electric power and the difficulty of promoting industrial and commercial distributed photovoltaic (PV) projects in China. The model makes full use of the conditions of different PV resources and different electricity prices in different places to optimize the scheduling of industrial production in different places. The model is embedded with two sub-models of the electricity price prediction model and distributed photovoltaic kWh cost model to complete the model parameters, in which the electricity price prediction model utilizes the LSTM neural network. The integrated model is then solved by the particle swarm algorithm. To verify the effectiveness of the model in solving the problem of off-site production scheduling on the demand side of electricity, the research team researched two off-site pharmaceutical factories belonging to the same large pharmaceutical company. Finally, the research data were substituted into the model for solving, and it was concluded that the optimization model could significantly reduce the cost of electricity consumption of the enterprise by about 7.9 %.

Agriculture is an industry that heavily relies on the environment. The increasing frequency of ex-treme disasters attributable to climate change has adversely affected agricultural land and dis-rupted the stability of the supply of agricultural products. Therefore, we implemented a research program focused on current strategies for adapting to agricultural meteorological disasters. The primary goal was to actively promote disaster prevention information and techniques through information platforms and applications and to provide refined forecasting and an early warning system to enhance preparedness for and recovery from agricultural disasters. This initiative can transform passive mitigation into dynamic action by disseminating crucial information to farmers. We integrated meteorological data and crop characteristics to develop disaster prevention strate-gies for the predisaster, during-disaster, and postdisaster stages to empower farmers to implement autonomous disaster prevention, ensuring their profitability and minimizing the impact of disas-ters. This paper presents an agricultural disaster prevention system involving cross-disciplinary collaboration to establish an early warning system for crop disasters. However, the effectiveness of the early warning system relies on the availability of complete meteorological and crop infor-mation, necessitating high-density agricultural meteorological stations, refined weather forecast services, historical crop damage data, and ongoing research and development on disaster preven-tion technology. In the system, a diversified social media interface is used to provide local farmers with weather forecast information. When impending disasters are identified, the platform acti-vates disaster prevention measures to reduce agricultural losses. This article paper introduces Taiwan’s agricultural disaster prevention system as a complete disaster prevention strategy.

YOLOv8, as an efficient object detection method, can swiftly and precisely identify objects within images. However, traditional algorithms encounter difficulties when detecting small targets in remote sensing images, such as missing information, background noise, and interactions among multiple objects in complex scenes, which may affect performance. To tackle these challenges, we propose an enhanced algorithm optimized for detecting small objects in remote sensing images, named HP-YOLOv8. Firstly, we design the C2f-D-Mixer (C2f-DM) module as a replacement for the original C2f module. This module integrates both local and global information, significantly improving the ability to detect features of small objects. Secondly, we introduce a feature fusion technique based on attention mechanisms, named Bi-Level Routing Attention in Gated Feature Pyramid Network (BGFPN). This technique utilizes an efficient feature aggregation network and reparameterization technology to optimize information interaction between different scale feature maps, and through the Bi-level Routing Attention (BRA) mechanism, it effectively captures critical feature information of small target objects. Finally, we propose the Smooth Mean Perpendicular Distance Intersection over Union (SMPDIoU) loss function. The method comprehensively considers the shape and size of detection boxes, enhances the model's focus on the attributes of detection boxes and provides a more accurate bounding box regression loss calculation method. To demonstrate our approach's efficacy, we conduct comprehensive experiments across the RSOD, NWPU VHR-10, and VisDrone2019 datasets. The experimental results show that the HP-YOLOv8 achieves 95.11%, 93.05%, and 53.49% in the [email protected] metric, and 72.03%, 65.37%, and 38.91% in the more stringent [email protected]:0.95 metric, respectively.

Short video addiction refers to a psychological dependency on short video applications, characterized by an intense attachment and an inability to control usage, leading to typical addiction symptoms. While its definition bears similarities to substance addiction, significant differences also exist. According to the Diagnostic and Statistical Manual of Mental Disorders, Fifth Edition (DSM-5), published in 2013, short video addiction has not yet been officially classified as an addiction disorder. To facilitate more in-depth and standardized research on short video addiction, it is essential to synthesize and organize existing studies on its theoretical foundations and mechanisms.

Determining the general-name-derived semantic relationships between geographic names often requires consulting many geographic name documents for verification. In geographic name translation and geographic name knowledge graphs, this method cannot meet the needs of large-scale extraction of general-name-derived semantic relationships between geographic entities. To solve this problem, this paper proposes a general-name derivation relation recognition method based on Prompt learning and Semantic Spatiotemporal Distribution Attention Feature Fusion (SSD-AFF). This method adopts a pipe-based relationship recognition strategy. First, the Prompt learning method is adopted to form a general-name derivation pattern with the general-name-derived geographical name category and the original geographical name category as the prompt word, and then the derivation pattern is combined with the geographical name as the input of the model so that the recognition problem of the general-name derivation of the geographical name can be transformed into a classification problem using the bidirectional language model. Then, by analyzing the characteristics of the semantic association and geographical spatio-temporal distribution between the general-name-derived geographical name and the original geographical name, the semantic spatio-temporal distribution characteristics of the general-name-derived geographical name are constructed. Finally, the network model based on the semantic spatio-temporal distribution Attention Feature Fusion (SSD-AFF) is used to distinguish the general-name-derived semantic relationships. The experimental results show that the proposed method has good performance. It can effectively mine the general-name-derived semantic relations between the vector data of geographical entities and has important application value in geographical name translation and geographical name knowledge maps.

Taiwan's bed and breakfast (B&B) development has been more than 25 years ago, from the first generation of retirement to the B&B industry, serving tourists from all over the world accom-modation, providing breakfast and accommodation mode to the present, after the change of employees from the second generation, more and more attention is paid to the cultivation and cultivation of business ability. With the advent of the era of AI technology networking, the ca-pabilities required for B&B operation are more focused on all aspects of service, and the good marketing ability of B&B can promote a green chimney-free tourism economy, which is also a favorite industry of various governments and the public. This study explores the basic vocational competency indicators required for running a B&B, with (1)EQ emotion management skills, (2)Financial management ability, (3)(SK) technical skills, and (4)Marketing and promotion management capabilities. Through the study method, the K-S Z test was determined by the con-sensus conclusion of expert reliability and validity p value

Quantifying the landscape pattern change can effectively demonstrate the ecological progresses and the consequences of urbanization. Based on remotely sensed land cover data in 1994, 2000, 2006 and a gradient analysis with landscape metrics at landscape- and class- level, we attempted to characterize the individual and entire landscape patterns of Shanghai metropolitan during the rapid urbanization. We highlighted that a roadscape transect approach that combined the buffer zone method and the transect-based approach was introduced to describe the urban-rural patterns of agricultural, residential, green, industrial, and public facilities land along the railway route. Our results of landscape metrics showed significant spatiotemporal patterns and gradient variations along the transect. The urban growth pattern in two time spans conform to the hypothesis for diffusion–coalescence processes, implying that the railway is adaptive as a gradient element to analyze the landscape patterns with urbanization. As the natural landscape was replaced by urban landscape gradually, the urban fringe expanded radically. The results also showed that the desakota region expanded its extent widely. Satellite towns witnessed the continual transformation from the predominantly rural landscape to peri-urban landscape. Furthermore, the gap between urban and rural areas remained large especially in public service. More reasonable urban plans and land use policies should push to make more of an effort to transition from the urban-rural separation to coordinated urban-rural development. This study is a meaningful trial in demonstrating a new form of urban–rural transects to study the landscape change of large cities from a strategic viewpoint. By combining gradient analysis with landscape metrics, we addressed the process of urbanization both spatially and temporally, and provided a more quantitative approach to urban studies.

The growing demands of material longevity in marine environments necessitate the development of highly efficient, low-cost and durable corrosion protective coatings. Although magnesium alloys are widely used in the automotive and aerospace industries, severe corrosion issues still hinder their long-term service in naval architecture. In present work, an epoxy composite coating containing sericite nanosheets is prepared on the AZ31B Mg alloy by one-step electrophoretic deposition method to improve corrosion resistance. Due to the PEI modification, positively-charged sericite nanosheets can be highly orientated in an epoxy coating under the influence of an electric field. The sericite-incorporated epoxy coating prepared in the emulsion with 4 wt.% sericite exhibits the highest corrosion resistance in 3.5 wt.% NaCl solution, as manifested by electrochemical corrosion and long-term immersion tests. The highly-orientated sericite nanosheets in epoxy coating provide excellent barrier effect against corrosive media, thereby significantly improving the long-term anti-corrosion performance of the epoxy coating. This work provides new insight toward the design of lamellar filler/epoxy coatings with superior anticorrosion performance and shows promise in the corrosion protection of magnesium alloys.

Electrically conductive polymer composites are in high demand for modern technologies, however, the intrinsic brittleness of conducting conjugated polymers and the moderate electrical conductivity of engineering polymer/carbon composites have highly constrained their applications. In this work, super high electrical conductive polymer composites were produced by a novel hot embossing design. The polydimethylsiloxane (PDMS) composites containing short carbon fiber (SCF) exhibited an electrical percolation threshold at 0.45 wt%, and reached a saturated electrical conductivity of 49 S/m at 8 wt% of SCF. When reduced the sample thickness from 1.0 mm to 0.1 mm by the hot embossing process, a compression-induced percolation threshold occurred at 0.3 wt%, while the electrical conductivity was further enhanced to 378 S/m at 8 wt% SCF. Furthermore, the additional of a second nanofiller of 1 wt%, such as carbon nanotube or conducting carbon black further increased the electrical conductivity of the PDMS/SCF (8 wt%) composites to 909 S/m and 657 S/m, respectively. The synergy of the densified conducting filler network by the mechanical compression and the hierarchical micro-/nanoscale filler approach has realize super high electrical conductive yet mechanical flexible polymer composites for modern flexible electronics applications.

Edvard Munch, a founder of Expressionism was pre-occupied with depicting his subjective experience and the most prolific painter of self-portraits since Rembrandt. Based on evidence that faces and self-related images are more salient than other objects it is plausible that self-portraits, in which the subject and object are the same, reflect the artist’s state of mind. Although he suffered from a variety of physical and psychological illness Munch was not diagnosed with any specificity in his lifetime. Posthumous diagnoses include schizophrenia, anxiety, bipolar and other disorders. Recent research has revealed altered visual perception in such patients. The present study empirically analysed three stylistic elements of Munch’s painted self-portraits and portraits: contrast, colour and fractal dimension and his painted productivity, to determine if variations correlate with critical life events and if so whether they indicate states of mind. It found significant increases in contrast and colour brightness and persistent high complexity during critical periods supporting the conclusion that Munch is diagnostically best described as suffering from early onset schizophrenia and comorbid social anxiety disorder.

Many have speculated that events of personal and financial loss in Rembrandt’s life caused depression and that this is revealed by examination of his self-portraits particularly those painted in old age. Some report detecting various physiological diseases associated with aging, including vision impairment, which may have affected his mood and work. Aging and neurodegenerative disease which often accompanies it, are both associated with depression. Recent advances in imaging and computer technology make it possible to empirically examine changes in artistic style which can contribute to understanding artists’ physical and mental health. In the current study changes in contrast, colour and fractal dimension were measured in the entire corpus of Rembrandt’s painted self-portraits and portraits to determine whether changes in style indicate depression or disease. Productivity was also examined as an indirect indicator. Given the high salience attributed to self-images, it also examined whether differences in style could be detected between self-portraits and portraits of related and unrelated others. The results indicate that it is unlikely that Rembrandt suffered from unipolar or bipolar depression, age-related cognitive decline, or neurodegenerative disease. The data are consistent with someone experiencing episodes of low mood consistent with normal grieving and adversity followed by resilient recovery. There is evidence of a gradient in saliency and complexity between self-portraits and related and unrelated portraits, of a less formal style in portraits of related others and of a ‘late’ style identified by leading art historians consistent with macular degeneration. The results are also consistent with an association of aesthetic preference with mid-level fractal values tending towards the Golden Mean long associated with beauty in nature and in art.

Researches on the runoff and sediment reduction effects of soil and water conservation measures are being on the rise, which is of great significance for carrying out strategic on soil and water conservation in the Yellow River Basin. Through the analysis of various soil and water conserva-tion measures, runoff, sediment, and rainfall datas in the Sanchuan River Basin from 1960 to 2019, we use the lagrange multiplier method to determining the threshold year of soil and water con-servation measures on runoff and sediment processes. The preliminary conclusion is as follows: The trend of flood season rainfall and annual rainfall in the Sanchuan River Basin is consistent. The 10-year average rainfall in each periods indicates that before 2000, it gradually decreased and then significantly increased. The 10-year average runoff showed a gradual decrease before 2010, followed by a sudden increase, while the 10-year average sediment has shown a decreasing trend years by years, especially after the centralized treatment period. Terrace and dam measures show a trend of first decreasing, then increasing, and then approaching stability during different treat-ment periods, while the trend of forest and grass measures is slightly decreasing and then in-creasing rapidly. The runoff and sediment reduction effects of various soil and water conservation measures during different treatment periods indicate that the runoff reduction effect reached its peak in 2005, while the sediment reduction benefit reached its best in 2015. Based on the compre-hensive benefits of runoff and sediment regulation, 2015 are considered as the threshold year for various soil and water conservation measures, with each measure areas being 4.86 × 104, 17.91 × 104, 1.20 × 104, and 0.83 × 104hm2, respectively. The research results will have certain reference significance for the high-quality development of soil and water conservation in the Yellow River Basin.

The task of weakly supervised point cloud semantic segmentation has received widespread attention and also has been widely used in autonomous driving, robotics, and modern industries. Due to the high dimensionality and large volume of point cloud data, many technical difficulties appeal to weakly supervised semantic processing, especially segmentation. However, weakly-supervised schemes usually provide only partial labelling information of the underlying point cloud data and thus need to effectively extract local features, geometric information, and contextual relationships only using these limited labelled data for supervised learning. To improve weakly-supervised semantic segmentation, we propose a novel segmentation network through the boundary-based feature aggregation based on a K-NN algorithm with down-sampling operation, and also introduce the smoothness loss and Siamese loss for effective segmentation. The experiments on public datasets demonstrate that our presented segmentation method exceeds most of the existing fully supervised and weakly-supervised methods in terms of mIoU. Specifically, our network has high segmentation accuracy on the labels of objects with similar geometrical structures, such as ceiling, wall, floor, chair and table, reaching 91.2%, 98.8%, 83.3%, 75.3% and 80.2%, respectively. Extensive experiments also illustrate its robustness, effectiveness, and generalization of the proposed weakly supervised segmentation network.

Variable flow emitters are a new type of emitter for underground drip irrigation that are used in locations where soil moisture is difficult to transport to the surface, which leads to crop emer-gence difficulties. The flow channel structure parameters of emitters affect the hydraulic per-formance of the emitter and its anticlogging ability. In this study, the variable flow emitter at the conventional low–flow water supply stage is taken as the research object. A combination of CFD numerical simulation of a two–phase flow of water and sand and clear water testing of test samples is applied to study the influence laws of 10 groups of variable flow emitter structural combinations on the effluent flow rate (q), flow index (x), particle passage rate and flow field inside the flow channel. The results show that the Realizable k–ε turbulence model can be used to simulate the flow field inside the variable flow emitter flow channel. The nRMSE between the measured and simulated values of q is 11.23%, and the relative error between the measured and simulated values of x is 4.66%, which gives a high simulation accuracy. The polar analysis shows that the tooth angle A has the smallest effect on the effluent flow rate q0.1 under 0.1 MPa, x, and particle passage rate of the variable flow emitter. The depth of the flow channel D, the spacing of the teeth B, and the height of the teeth E have a different order of precedence in the influence of the three indices, which are D > B > E > A, B > E > D > A, and E > B > D > A, respectively. The value of particle passage rate is positively correlated with the mean flow velocity (v) and the mean turbulent kinetic energy (k) in the flow channel, and particle passage rate tends to increase and then decrease with the increase of x. The retention time (t) of the particles in the flow channel is closely related to the magnitude of v and k. Three multivariate linear regression equations (R2 = 0.883 ~ 0.995) were constructed for q0.1, x, and particle passage rate versus the flow channel structural parameters. Using the scipy.optimize.minimize function in Python, we de-termined the three optimal combinations of flow channel structural parameters corresponding to better hydraulic performance: q0.1 is 1.5 or 2 L/h (objective function y = min x), better clogging resistance (y = max particle passage rate), and both (y = min (0.5 x - 0.5 particle passage rate)). The research results can provide a ref-erence for the optimal design of variable flow emitters.

In order to reduce the silique shattering loss of rapeseed mechanical harvesting process, based on the state of force on the silique during rapeseed harvesting reel branch, Ningza 1810, Zhenyou 8 and Fengyou 306 were used as research objects, and the experimental research on the factors affecting rapeseed siliques shattering was carried out using the swing impact method. The experimental analysis showed that: rapeseed varieties, silique moisture content, silique growth position, collision material, impact speed, force position and other factors had significant effects on silique shattering. The impact velocity was less than 1.5m·s-1, the difference on the effect of each factor on pod-shattering was not significant, it was not easy to shatter when the moisture content of rapeseed silique was higher. The impact resistance of the front side of rapeseed was 2 to 4 times that of the bonding surface of rapeseed petals, the shattering rate of the top rapeseed silique was twice that of the bottom siliques, when siliques were supported, they were more likely to shatter under external forces than when they were unsupported. The experimental study of the mechanical properties of rapeseed siliques was carried out using the impending fracture method, the experimental analyses showed that the support position and force position of the silique, the loading speed and the growth position of the silique had a significant effect on the mechanical properties of the silique. The maximum cracking force was higher and bending strength was stronger when the body of the silique was supported, which the range of the maximum cracking force were 3.05N to 4.16N, and the bending strength range were 8.48 MPa to 11.57 MPa. The maximum cracking force and bending strength of the silique was stronger when the front side of the silique petal was pressurized than when the bonding surface of the petal was pressurized. Based on Pearson's correlation and grey correlation analysis, the morphological characteristics of rapeseed siliques were ranked in order of their influence on the performance of siliques in terms of the angle between silique and stalk, stalk diameter, petal thickness, beak length, silique thickness, silique width and silique length. This study can be used as a reference for the design and optimization of the rapeseed harvesting reel branch mechanism and the selection of machine harvestable rapeseed varieties.

Background: Coronavirus Disease 2019 (COVID-19) has been demonstrated to be the cause of pneumonia. Nevertheless, it has not been reported as the cause of acute myocarditis or fulminant myocarditis. Case presentation: A 63-year-old male was admitted with pneumonia and cardiac symptoms. He was genetically confirmed as having COVID-19 according to sputum testing on the day of admission. He also had elevated troponin I (Trop I) level (up to 11.37 g/L) and diffuse myocardial dyskinesia along with a decreased left ventricular ejection fraction (LVEF) on echocardiography. The highest level of interleukin-6 was 272.40 pg/ml. Bedside chest radiographs showed typical ground-glass changes indicative of viral pneumonia. Laboratory test results for viruses that cause myocarditis were all negative. The patient conformed to the diagnostic criteria of the Chinese expert consensus statement for fulminant myocarditis. After receiving antiviral therapy and mechanical life support, Trop I was reduced to 0.10 g/L, and interleukin-6 was reduced to 7.63 pg/ml. Moreover, the LVEF of the patient gradually recovered to 68%. The patient died of aggravation of secondary infection on the 33^rd day of hospitalization. Conclusion: COVID-19 patients may develop severe cardiac complications such as myocarditis and heart failure. This is the first report of COVID-19 complicated with fulminant myocarditis. The mechanism of cardiac pathology caused by COVID-19 needs further study.

Combining Matrix-Assisted Laser Desorption/Ionization Time-of-Flight (MALDI-TOF) spectra data and artificial intelligence (AI) has been introduced for rapid prediction on antibiotic susceptibility test (AST) of S. aureus. Based on the AI predictive probability, the cases with probabilities between low and high cut-offs are defined as “grey zone”. We aimed to investigate the underlying reasons of unconfident (grey zone) or wrong predictive AST. A total 479 S. aureus isolates were collected, analyzed by MALDI-TOF, and AST prediction, standard AST were obtained in a tertiary medical center. The predictions were categorized into the correct prediction group, wrong prediction group, and grey zone group. We analyzed the association between the predictive results and the demographic data, spectral data, and strain types. For MRSA, larger cefoxitin zone size was found in the wrong prediction group. MLST of the MRSA isolates in the grey zone group revealed that uncommon strain types composed 80%. Amid MSSA isolates in the grey zone group, the majority (60%) was composed of over 10 different strain types. In predicting AST based on MALDI-TOF AI, uncommon strains and high diversity would contribute to suboptimal predictive performance.