In recent years, cemented tailings/paste backfill (CPB) become more and more important to maintain mine structure and keep mining stope to be stable in deep underground mining. Deep mining process often accompanied by blasting, rock burst and other high-speed dynamic loading. So it’s important to make research on dynamic behavior and characteristics of CPB. In this paper, a series of dynamic loading tests on CPB specimens by SHPB were taken to study the characteristic of stress-strain, dynamic strength, deformation and failure of CPB. The experimental results revealed that some CPB specimens have 1~2 lower stress peaks after reaching the peak stress before getting completely failed. The greater the cement-sand ratio was, the more obvious of strain reaction was. This property mainly showed like follows. The greater the cement-sand ratio was, the greater the dynamic compressive strength was under similar velocity impact; the dynamic compressive strength and the average strain rate were quadratic equation relationship, and the greater the cement-sand ratio was, the higher increase rate of dynamic compressive strength caused by strain rate. The dynamic compressive strength enhancement factor increased with the increase of the strain rate, and is larger than that of rock samples. The failure forms of CPB specimens under low-speed impact were almost the same as them under static uniaxial and triaxle compression. The CPB specimens were crushed broken under the critical strain rate, similar to the failure mode of low strength concrete. The experimental research results will improve our understanding the dynamic mechanical property of CPB and help to guide the strength design of deep mining backfill.

After long years of development, the technology of analyzing the working condition of power units based on vibration signals has had relatively stable applications, but the accuracy and the degree of automation and intelligence for fault diagnosis are still inadequate due to the limitations of the current development of key technologies. With the development of big data and artificial intelligence technology, the involvement of new technologies will be an important boost to the development of this field. To support the subsequent research, bibliometrics is used as a tool to sort out the development of the technology in this field at the macro level; at the micro level, the classical and key literature is studied to grasp the development status at the technical level and prepare for the selection of entry points to continue in-depth innovation afterwards.

This letter presents a dual-frequency terahertz amplitude modulator based on a cross-shaped structure and U-shaped metal patches. Its structural unit is a typical metal-substrate structure. The top metal consists of a cross-shaped structure and U-shaped metal patches, and the bottom substrate layer is made of quartz. Amplitude modulation is achieved by adjusting the temperature of the vanadium dioxide (VO2) patches. The modulation depth can be approximately 75%. The mechanism of the resonance frequency is explained by the equivalent circuit model. The proposed structure shows good amplitude modulation capability at different incidence and azimuth angles by changing the location of the VO2 patches. The dual-frequency terahertz amplitude modulator can be used in terahertz communication, imaging, etc.

Orchids are often a mystery because of their close and complex relationships with various microorganisms in the natural environment. Orchids rely on microorganisms to obtain nutrients, affecting their seed germination, protocorm, and adult plant growth. Currently, the majority of relevant research is concentrated on isolating and identifying environmental microorganisms that support orchid development and growth. With the development of metagenomic technology, our understanding of orchid mycorrhizal fungi (OMF) and root-associated bacteria (RAB) has been expanded. New research results and discoveries have emerged, which require a comprehensive assessment to provide a reference for studying microorganisms related to orchids. Therefore, we present a comprehensive summary, identifying significant inadequacies of present methodologies while providing ideas for further research.

Nowadays, the study of preparing silica/rubber composites, which can be used in “green tire”, in energy saving method is fast-growing. In our work, silica modified by using alcohol polyoxyethylene ether (AEO) and 3-Mercaptopropyltriethoxysilane (K-MEPTS) together were investigated. Thermal gravimetric analyzer (TGA) result indicated that both AEO and K-MEPTS could be grafted on the silica surface. Raman spectroscopy confirmed that the AEO could generate a certain steric hindrance for the mercaptopropyl group on K-MEPTS. Silica modified by using AEO and K-MEPTS together can be completely co-coagulated with the rubber in preparing silica/natural rubber (NR) composites by latex compounding method. AEO can form a physical interface between silica and rubber; meanwhile, K-MEPTS can form a chemical interface between silica and rubber. The effects of chemical and physical interface between silica and rubber on dynamic and mechanical performances of silica/NR composites were also given in this research. A proper combination of physical and chemical interface between silica and NR can improve performances of silica/NR composites.

Japanese encephalitis is a zoonotic disease caused by Japanese encephalitis virus (JEV). It is mainly epidemic in Asia with an estimated 69,000 cases occurring per year. However, no approved agents are available for the treatment of JEV infection, and existing vaccines cannot resist various types of JEV strains. Drug repurposing is a new concept for finding new indication of existing drugs, and recently, it has been used to discover new antiviral agents. Identifying host proteins involved in the progress of JEV infection and using these proteins as targets are the center of drug repurposing for JEV infection. In this study, based on the gene expression data of JEV infection and the phenome-wide association study (PheWAS) data, we identified 286 genes participating in the progress of JEV infection using the systems biology methods. The enrichment analysis of these genes suggested that the genes identified by our methods were predominantly related to viral infection pathways and immune response-related pathways. We found that bortezomib which can target these genes may have potential effect on the treatment of JEV infection. Subsequently, we evaluated the antiviral activity of bortezomib using the JEV-infected mice model. The results showed that bortezomib can lower JEV-induced lethality in mice, alleviate suffering in JEV-infected mice and reduce the damage in brains caused by JEV infection. This work provides a new method for the development of antiviral agents.

The aim of this paper is to use the elementary method and the properties of the second kind Stirling numbers to study the congruence properties of a new sequence, which is closely related to Fubini polynomials and Euler numbers, and give some interesting congruences for it. This solves a problem proposed by the first author at an unpublished paper.

The greatly diversified flowering plants (angiosperms) are the dominating and defining group in the current earth ecosystem. However, from which group by what way the flowers, especially their gynoecia (key characteristics of angiosperms), are derived have been the questions in botany unanswered over centuries. Such an embarrassing situation can be attributed to the lack of plants with partially enclosed ovules, which are supposed to be a post between gymnosperms and angi-osperms. Here we report a fossil plant that has an apparent coniferous vegetative and reproduc-tive morphologies but has a single seed partially wrapped by the subtending bract. Such a mor-phology suggests that the carpels in angiosperms may be equivalent to bracts enclosing their axil-lary seed(s). Such a non-traditional interpretation of the homology of angiosperm carpels is com-patible with various new progresses made in botany and is in line with Tomlinson’s recent hy-pothesis. Together with other fossil evidence reported recently, it appears that gynoecia in angio-sperms are derived in multiple ways.

This paper first introduces the main classification of brain diseases and the main causes of these diseases. It is followed by wavelet analysis, which is a mathematical function or wave-like pattern used to transform data, which can decompose the signal into different wavelet functions, each of which is related to a specific scale or frequency. Wavelet analysis has been applied in many fields such as image processing, data analysis and engineering. In addition, wavelet is also used in the analysis of biological signals. Wavelet analysis breaks down brain signals, such as EEG or fMRI data, into various frequency components at different scales. Wavelet analysis provides time-frequency localization. Pattern recognition can be enhanced by isolating salient features in the data. Wavelet denoising can effectively separate noise from underlying brain signals. Wavelet denoising usually adopts threshold method. Wavelet analysis can enhance pattern recognition by isolating salient features in the data. Researchers can train machine learning models based on these wavelet-derived features to recognize specific patterns associated with different neurological disorders. Wavelet analysis can track these changes by continuously evaluating the frequency content of the neuroimage data over time. Through continuous efforts, wavelet theory and technology have become valuable tools in the field of neuroscience and brain disease research.

To explore the effects of pymetrozine on the reproductive behavior of N. lugens, we established a bioassay method to accurately evaluate the toxicity of pymetrozine in N. lugens and establish the level of pymetrozine resistance of N. lugens in the field. In this study, pymetrozine’s effects on the fecundity of N. lugens were evaluated using the topical application method and rice-seedling dipping method. Moreover, the resistance of N. lugens to pymetrozine in a pymetrozine-resistant strain (Pym-R) and two field populations (YZ21 and QS21) was determined using the rice-seedling dipping method and fecundity assay methods. The results showed that treatment of N. lugens third-instar nymphs with LC15, LC50, and LC85 doses of pymetrozine resulted in significantly reduced male fertility and female fecundity. In addition, N. lugens adults treated with pymetrozine using the rice-seedling dipping and topical application method also exhibited significantly in-hibited male courtship, fertility, and female receptivity. Using the rice-stem dipping method, pymetrozine resistance was shown to be at high levels in Pym-R (194.6-fold), YZ21 (205.9-fold), and QS21 (212.8-fold), with LC50 values of 522.520 mg/L (Pym-R), 552.962 mg/L (YZ21), and 571.315 (QS21) mg/L. However, when using the rice-seedling dipping or topical application fe-cundity assay method, Pym-R (EC50: 14.370 mg/L, RR=12.4-fold; ED50: 0.560 ng/adult, RR=10.8-fold), YZ21 (EC50: 12.890 mg/L, RR=11.2-fold; ED50: 0.280 ng/adult; RR=5.4-fold), and QS21 (EC50: 13.70 mg/L, RR=11.9-fold) exhibited moderate or low levels of resistance to pymet-rozine. Our studies show that pymetrozine can significantly inhibit the fecundity of N. lugens. The fecundity assay results showed that N. lugens only developed low to moderate levels of resistance to pymetrozine, indicating that pymetrozine can still achieve effective control on the next gen-eration of N. lugens populations.

Purpose: Acute kidney injury (AKI) is a severe symptom of the 2019 novel coronavirus disease (COVID-19), especially for patients in a critical condition.This study explored the potential mechanism of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) on AKI at the single-cell level. Methods: 15 normal human kidney samples were collected and analyzed using single-cell RNA sequencing (scRNA-seq). Subsequently, we analyzed the components and proportions of kidney cells expressing the host cellular receptor ACE2 and the key protease TMPRSSs family, and analyzed the expression differences in Occidental and Asian populations. Results: We drafted the currently available world's largest human kidney cell atlas with 42,589 cells and identified 19 clusters through unsupervised hierarchical clustering analysis. ACE2 and TMPRSSs genes were significantly co-expressed in podocytes and proximal convoluted tubules as potential host cells targeted by SARS-CoV-2. Comparative analysis showed that ACE2 expression in kidney cells was no less than that in the lung, esophagus, small intestine and colon, suggesting that the kidney may be an important target organ for SARS-CoV-2. In addition, given the high expression of ACE2 and kidney disease-related genes in Occidental donors relative to Asian donors, Occidental populations with SARS-CoV-2 infection might be a higher risk of of kidney injury.

In our article in Genome Biology Ecology six years ago, one complete plastid genome of Belian was assembled for comparative analyses of the plastomes in Lauraceae. However, Ariati et al. (2023) concluded that our sequenced Belian individual could be located in the clade of Myristicaceae instead of that of Lauraceae. Here, we performed re-analyses of additional two Belian plastomes, along with 42 plastomes from plants spanning ten families of the Magnoliids. The plastomes of the three Belian individuals range from 157,535 to 157,577 bp in length. Comparative genomic analysis revealed 170 mutation sites in their plastomes, which include 111 substitutions, 53 indels, and six microinversions. Phylogeny was reconstructed using maximum likelihood and Bayesian approaches for 44 magnoliids species indicated that our three Belian individuals are nested among the species in the family Lauraceae rather than Myristicaceae.

The Yixian Formation (Lower Cretaceous) of China is famous worldwide for its fossils of early angio-sperms, but there is only one record of flower bud hitherto. A previous fossil record of flower bud just showed the appearance and lacked any internal details. Such a lacuna in knowledge of flower buds hin-ders our understanding of the evolution of flowers. Our new specimen was collected from an outcrop of the Yixian Formation (the Barremian-Aptian, Lower Cretaceous) near Dawangzhangzi, Lingyuan, Liao-ning, China. The specimen was observed and photographed using a Sony ILCE-7 digital camera and a Nikon SMZ1500 stereomicroscope, and details were observed using a TESCAN MAIA3 SEM. Our ob-servations document a fossil flower bud, Archaebuda cretaca sp. nov, from the Lower Cretaceous of China. The occurrence of two species of Archaebuda in the Yixian Formation not only confirms the ex-istence of the expected gynoecium (and possible androecium) in a flower bud, but also underscores the occurrence of typical flowers in the Early Cretaceous.

Land plants have undergone their great diversification and evolution in the past 400 million years. Although appearing complex and hard to grasp, the evolution of plants centers around an invariable core development process, SRC (Sexual Reproductive Cycle). Various modifications have been added sequentially to this core process, and thus creating various novel organs and distinguishing their bearers one from another. Reproductive organs of all land plants, including sporangium, megasporangium, metamegasporangium (= ovule), and various metamegasporangium complexes, are derived from terminal sporangia in the earliest land plants. Throughout the million-year-long evolution, plants sequentially recruit associating accessories to protect their vulnerable core parts (spore and gamete). The occurrence of every single of these novelties is a stair marking land plant reproduction evolution and leads to enhanced offspring development conditioning (ODC).

Resection of malignant lesions in the oral and maxillofacial area causes functional and morphological defects. To recover from these defects, reconstruction surgery is needed such as a primary closure or a flap. There are advantages and disadvantages to the method of using the primary closure and the flap, and the choice of procedure is entirely up to a surgeon. The purpose of this study is to evaluate availability of primary closure in patients. For 10 years from January 2010 to May 2020, patients who recovered using flaps after removing malignant lesions from the oral cavity and those who closed the lesion using primary closure were investigated. The investigation was conducted by searching the database of the hospital. There were 85 patients who removed malignant lesions in the oral and maxillofacial area, and among them 16 patients closed the soft tissue defects using primary closure. Operation time, histologic types, stages, wound status, and period of hospitalization according to the patients' medical records were investigated retrospectively. Between the staging and the primary closure, statistically significant differences were observed between stage I and stage II patients in 13 patients using the primary closure. (P=0.046). Statistically significant differences were identified between operation time and primary closure, with an average of 4.02 hours (P=0.015). The average period of hospitality for patients who underwent primary closure was 13.4 days, compared to 26.7 days for those who underwent flap surgery. This difference was statistically significant (P=0.0003). This study evaluated the use of primary closure in patients who underwent resection of malignant lesions in the oral and maxillofacial area. Although the majority of patients underwent reconstruction with flaps, our results showed that primary closure can be a viable option for certain patients with early-stage lesions. Therefore, oral and maxillofacial surgeons should carefully consider various evaluation criteria and select appropriate reconstruction methods to optimize functional and aesthetic outcomes for each patient.

The Shimensi super-large tungsten polymetallic deposit is located in Late Jurassic- Early Cretaceous Porphyry-Skarn tungsten ore belt in the south Yangtze metallogenic belt. There are 3 types of mineralization: veinlet-disseminated type, thick quartze vein type and hydrothermal crypto-explosive breccia type. Based on geological studies, this paper presents new petrographic, microthermometric, laser Raman spectroscopic and hydrogen and oxygen isotope research of the fluid inclusions from the deposit. The results show that there are five different types of fluid inclusions: liquid-rich inclusions, vapor-rich inclusions, pure liquid inclusions, pure vapor inclusions, and fluid inclusions containing a solid crystal. The homogenization temperatures of the fluid inclusion range from 140℃-270℃, the salinities are 3%-5% NaCleq and the densities of ore-forming fluid range from 0.64 g/cm3 to 0.99 g/cm3. For the analyses of Laser Raman spectroscopic, the ore-forming fluids can be approximated by a Ca2+-Na+-SO42--Cl- fluid system with small amount of CO2, CH4 and N2. Otherwise, the datas of the pressure, pH and Eh show a fluid metallogenic environment of low pressure, weak acid and weak reduction. The values of the homogenization temperature in 3 types of orebodies suggest that the mineralization is characterized by the decrease of the temperature under the condition of the fluid immiscibility. The H-O isotope values are interpreted to indicate that the ore-forming fluids are mainly composed of magmatic water, and also the meteoric water was added with the process of the magma rising.

This study used Dutch potatoes at the end of dormancy as the material to explore the impact of menthol (0.2 and 0.5 g/kg based on potato mass) treatment on sprouting inhibition and potato quality. The findings revealed that a menthol concentration of 0.5 g/kg effectively inhibited potato tuber sprouting and significantly reduced glucoside alkaloids production. After a storage period of 15 days, the sprouting percentage and glucoside alkaloids content of potatoes treated with 0.5 g/kg menthol were observed to be significantly lower at 4.17% and 68.63 mg/kg, respectively, compared to the control group which exhibited values of 100% and 282.01 mg/kg, respectively (P < 0.05). Throughout the storage period, 0.5 g/kg of menthol promoted respiration, reduced malondialdehyde production in potatoes, inhibited polyphenol oxidase activity, and slowed down tissue browning. Additionally, it mitigated the decline in starch and soluble protein content, inhibiting the accumulation of reducing sugars.

Fabrication of durable materials with excellent oil adsorption capacity and separation performance for the treatment of oily wastewater is meaningful based on smart responsiveness. Herein, a solvent-responsive melamine sponge (MS) was developed via silanization followed by the in-situ growth of zeolitic imidazolate framework-8 (ZIF-8). Detailed characterization of the resultant composite MS was conducted using scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR). The multiscale hierarchical MS substrate exhibited highly hydrophobic property in the pH range of 1-11, along with a satisfactory adsorption capacity in the range of 65.4-134.2 g/g for different oils. The modified surface transformed from superhydrophobicity/superlipophilicity to superhydrophilicity/underwater superoleophobicity upon ethanol wetting, reverting to its original superhydrophobic state upon drying. The separation flux of the MS substrate was above 1.5×104L/m2h for both oil and water removal, along with the separation efficiency more than 98.7%. No obvious changes of the separation performance after 50 successive immiscible oil/water separation indicated the excellent durability and robustness of the anchored ZIF-8 nanoparticles on the surface of modified MS substrate. More importantly, oil-in-water emulsion separation was successfully carried out via the ZIF-8 MS composite with a high separation efficiency over 99.1%. The developed smart sponge with high oil absorption capacity, excellent chemical stability and fire resistance exhibited a wide range of potential practical applications in the convenient treatment of oily wastewater.

In recent years, Chinese manufacturing enterprises compete to chase the wave of "digital revolution", digital empowerment has become an important strategic path of technological reform for many manufacturing enterprises. Based on the micro data of listed companies, this paper investigates the impact of digital transformation of Chinese listed companies on the quality of their export products. It is found that digital transformation can significantly improve the quality of enterprises' export products. After a series of robustness tests, this conclusion is still valid, and there are two ways to improve innovation performance and total factor productivity. The export product quality enhancement effect of enterprise digital transformation also has the heterogeneity of ownership, region and industry. In the further study, this paper also examines the impact of digital transformation on the internal salary gap of enterprises, and finds that digital transformation may increase the internal salary gap of enterprises, and form a "masking effect" on the quality of export products. To a certain extent, this paper deepens the understanding of the study of enterprise digital transformation on the quality of export products and its differences, and provides certain guidance for enterprises to implement the strategy of digital transformation.

To estimate the degree of quantum entanglement, it is important to understand the statistical behavior of functions of spectrum of density matrices such as von Neumann entropy, quantum purity, and entanglement capacity. These entangle- ment metrics over different generic state ensembles have been studied intensively in the literature. As an alternative metric, in this work we study sum of square root spectrum of density matrices, which is relevant to negativity and fidelity in quantum information processing. In particular, we derive the exact mean and vari- ance of sum of square root spectrum over the Bures-Hall generic state ensemble extending known results obtained recently over the Hilbert-Schmidt ensemble.

The main idea of this paper is to investigate the exact solutions and dynamic properties in optical nanofibers, which is modeled by space-time fractional perturbed nonlinear schr\"odinger equation involving Kerr law nonlinearity with conformal fractional derivative. Firstly, by the complex fractional traveling wave transformation, the traveling wave system of the original equation is obtained, then a conserved quantity, namely the Hamiltonian is constructed, and the qualitative analysis of this system is conducted via this quantity by classifying the equilibrium points. Moreover, the prior estimate of the existence of the soliton and periodic solution is established via the bifurcation method. Furthermore, all exact traveling wave solutions are constructed to illustrate our results explicitly by the complete discrimination system for polynomial method.

Recent advances in satellite technology have brought enormous potential to ecosystem mapping, which is one of the fundamental components of environmental studies. In this paper, a Random Forest classifier is applied for the strict assessment of the efficiency of ecosystem mapping through a detailed comparative analysis between combined Sentinel-1 and Sentinel-2 data and stand-alone Sentinel-2 imagery over three priority ecosystems, including wetlands, riverine areas, and mangroves in Bangladesh. The collocated images, based on the integration of Sentinel-1 data with Sentinel-2 data, would do better than Sentinel-2 imagery alone over various ecosystems. Particularly, in this study, attention focused on the Hakaluki Haor area for the wetlands, the Padma-Jamuna River confluence for the riverine ecosystem, and the Sundarban forest for mangroves. By leveraging Synthetic Aperture Radar (SAR) data in C-band dual-polarization from Sentinel-1 and four spectral bands (blue, green, red, and near-infrared) from Sentinel-2, the study analyzes imagery from December 2022 to February 2023. A 5% cloud masking filter is applied to optical data to enhance accuracy. In this methodology, 70% of the total signature values are used for training the classification model and the remaining 30% for testing. It can be noticed from the results that with the use of fused data, remarkably high accuracy in classification has been improved, such as overall accuracies of 94.17% for mangroves, 87.30% for riverine, and 85.96% for wetland ecosystems. In contrast, the use of singular Sentinel-2 imagery yields lower accuracies of 91.56%, 85.21%, and 82.51% for the respective ecosystems. The integration of radar data is shown to provide critical information, especially in environments with dense vegetation or cloud cover, where optical data alone may be insufficient. The findings of this study underline the limitations of relying on Sentinel-2 imagery to capture complex details of diverse ecosystems and highlight the need to include Sentinel-1 data for a more holistic analysis. This fusion allows improved accuracy to be achieved, which not only brings in more depth of ecological knowledge but also underpins more effective conservation strategies.

Digital technology makes energy systems more dynamic, efficient, reliable and sustainable. Promoting the digital governance of renewable energy is not only a key part of energy transformation, but also an important initiative to cope with the global energy crisis, which provides a new impetus for realizing the goal of net-zero emissions. In order to achieve the "dual-carbon" goal, China has been actively promoting energy reform and enhancing the wide application of digital technologies in the development and utilization of renewable energy. The digital governance system and governance capacity of renewable energy is an important support for the modernization of the national governance system and governance capacity. Although the digital governance of renewable energy in China has better policy support and advantages, the dilemmas it faces are still relatively prominent, including unsound laws and policies, insufficient governance capacity, and security loopholes in digital technology, etc. Therefore, this paper proposes a problem-oriented approach to the digital governance of renewable energy. Therefore, this paper puts forward problem-oriented optimization suggestions to innovate the legal system of renewable energy digital governance, promote the digital transformation of China's renewable energy industry, provide development space for renewable energy digital governance in a diversified mode, and enhance the digital governance capacity by improving the renewable energy security system.

In recent decades, with the ever-growing scale of video data, near-duplicate videos continue to emerge. Data quality issue caused by near-duplicate videos is becoming more and more prominent, which has affected the application of normal videos. Although current studies on near-duplicate video detection can be helpful to uncover data quality issues for videos, they still lack a process of automatic merging for the video data represented by high-dimensional features, which are difficult to automatically clean the near-duplicate videos to improve data quality for video datasets. At present, there are few studies on near-duplicate video data cleaning. The existing studies have the sensitive problems of video data orderliness and clustering initial center under a condition that prior distribution is unknown, which seriously affect the accuracy of near-duplicate video data cleaning. To address the above issues, an automatic near-duplicate video data cleaning method based on a consistent feature hash ring is proposed in this paper. First, a residual network with convolutional block attention modules, a long short-term memory deep network, and an attention model are integrated to construct an RCLA deep network with the multi-headed attention mechanism to extract spatiotemporal features of video data. Then, a consistent feature hash ring is constructed, which can effectively alleviate the sensitivity of video data orderliness while providing a condition of near-duplicate video merging. To reduce the sensitivity of the initial cluster centers to results of near-duplicate video cleansing, an optimized feature distance-means clustering algorithm is constructed by utilizing a mountain peak function on a consistent feature hash ring, which can implement automatic cleaning of near-duplicate video data. Finally, experiments are conducted based on a commonly used dataset named CC_WEB_VIDEO and a coal mining video dataset. Compared with some existing works, simulation results demonstrate that the performance of the proposed method.

This paper studies a model of dynamic compensation and capital structure with managerial traits. We show that Optimistic manager perceives equity as more undervalued than debt, while, confident manager perceives debt as more undervalued than equity. Managerial risk aversion mitigates manager’s bias. The risk aversion of the optimistic manager has a convex effect on the optimal coupon. There exists the level of risk aversion eliminating the bias on the leverage. The managerial optimist has an ambiguous effect on the owner’s bankruptcy level. The risk aversion has a convex effect on the owner’s bankruptcy level. The optimistic/confident manager underestimates the credit spread. The risk aversion has convex effect on the credit spread. In contrast to rational manager, the optimistic/confident manger has higher level of effort. The risk aversion has a negative effect on the effort.

Currently, peptic ulcers are widely studied as an infectious disease caused by Helicobacter pylori primarily due to 3 supporting evidences, and this etiology may explain the other 3 observations, but cannot confront the challenges of the 15 major characteristics and the other 75 observations/phenomena of peptic ulcers. To address the challenges, a recently published Complex Causal Relationship with its accompanying methodologies was applied to analyze existing data. Peptic ulcers are identified as a psychosomatic disease triggered by psychological stress, where Helicobacter pylori plays a secondary role in only the late phase of ulceration. This new etiology elucidated all the 15 major characteristics and 81 observations/phenomena of peptic ulcers in a series of 6 articles. This sixth article focuses exclusively on the controversies surrounding the role of Helicobacter pylori in peptic ulcers. In-depth analyses find that all the 3 evidences supporting “peptic ulcers are an infectious disease caused by Helicobacter pylori” are deceiving, and 2 of the 3 explainable observations may have been misinterpreted. Meanwhile, the definitions of ‘etiological factor’ and ‘causality’ do not support ‘H. pylori infection is an etiological factor of peptic ulcers’, and existing literatures have presented a controversial view on the role of Helicobacter pylori in peptic ulcers. Interestingly, if “peptic ulcers are an infectious disease caused by Helicobacter pylori” is considered an illusion, all the characteristics of the disease, along with all the clinical, epidemiological, and laboratory observations/phenomena, can be fully understood. This illusion has misguided peptic ulcer research over the past 36 years with little progress in the field, and that may represent a widespread situation in modern medical research, resulting in a direct interference with the true understanding of disease. Evidently, keeping the concept “illusion” in mind may help remove a huge obstacle that impedes medical advance, thereby facilitating the in-depth study of disease.

The two-scale method (TSM) is an effective approach to simulate electromagnetic (EM) scattering from rough sea surface, to interpret physical interaction of EM wave with rough sea surfaces. The sea surface roughness spectrum and the cutoff wavenumber are two key factors affecting the accuracy of TSM simulation. This paper takes the geophysical model functions (GMFs) of different band as reference, and quantitatively studies the two factors based on the numerical simulation of different polarization backscattering coefficients. The numerical simulation demonstrates that Apel spectrum is more suitable for the backscattering simulation in C/X/Ku-band, and the optimal cutoff wavenumbers are also derived for TSM simulation of EM scattering in C/X/Ku-band. Then an empirical model function of optimal cutoff wavenumbers with respect to frequency, incident angle and wind speed are obtained with regression method. Finally, the simulation results with the new model function of cutoff wavenumber are compared with the GMF and measured data in different bands and they are all consistent. Moreover, a physical explanation for the optimal cutoff wavenumber is also given.

The article focuses on breast cancer, mammography, and artificial intelligence. First, breast cancer is a widespread health problem that affects millions of people worldwide, and mammography is a widely adopted screening method. Then it introduced the advantages of mammography after AI participation, and introduced the importance of early detection of breast cancer and the application of artificial intelligence in breast cancer detection and treatment. From these aspects extend to the entire medical field of artificial intelligence issues. Several times throughout the paper, ethical issues that could arise from applying AI to healthcare are highlighted. At the end of the article, the paper describes the continued development of AI-based mammography analysis over the next period of time.

Chronic obstructive pulmonary disease (COPD) is associated with high morbidity and mortality globally. Studies show that airway mucus hypersecretion strongly compromises lung function, leading to frequent hospitalization and mortality, highlighting an urgent need for effective COPD treatments. MUC5AC is known to contribute to severe muco-obstructive lung diseases, worsening COPD pathogenesis. Various pathways are implicated in the aberrant MUC5AC production and secretion MUC5AC. These include signaling pathways associated with mucus-secreting cell differentiation [ nuclear factor-κB (NF-кB)and IL-13-STAT6- SAM pointed domain containing E26 transformation-specific transcription factor (SPDEF), as well as epithelial sodium channel (ENaC) and cystic fibrosis transmembrane conductance regulator (CFTR)], and signaling pathways related to mucus transport and excretion-ciliary beat frequency (CBF). Various inhibitors of mucus hypersecretion are in clinical use but have had limited benefits against COPD. Thus, novel therapies targeting airway mucus hypersecretion should be developed for effective management of muco-obstructive lung disease. Here, we systematically review the mechanisms and pathogenesis of airway mucus hypersecretion, with emphasis on multi-target and multi-link intervention strategies for the elucidation of novel inhibitors of airway mucus hypersecretion.

Bearings are widely used in various types of electrical machinery and equipment. As their core components, failures will often cause serious consequences . At present, most methods of parameter adjustment are still manual adjustment of parameters. This adjustment method is susceptible to prior knowledge and easy to fall into the local optimal solution, failing to obtain the global optimal solution and requires a lot of resources.Therefore, this paper proposes a new method of bearing fault diagnosis based on wavelet packet transform and convolutional neural network optimized by simulated annealing algorithm.The experimental results show that the method proposed in this paper has a more accurate effect in feature extraction and fault classification compared with traditional bearing fault diagnosis methods. At the same time, compared with the traditional artificial neural network parameter adjustment, this paper introduces the simulated annealing algorithm to automatically adjust the parameters of the neural network, thereby obtaining an adaptive bearing fault diagnosis method. To verify the effectiveness of the method, the Case Western Reserve University bearing database was used for testing, and the traditional intelligent bearing fault diagnosis method was compared. The results show that the method proposed in this paper has good results in bearing fault diagnosis. Provides a new way of thinking in the field of bearing fault diagnosis in parameter adjustment and fault classification algorithms

Perinatal brain injury is a major public health problem burdened with high morbidity, mortality and severe neurological sequelae. Despite advances in neonatal life-saving technologies, neonatal encephalopathy lacks specific and effective treatment. Therefore, mechanisms of central nervous system changes associated with perinatal brain injury have been a hot topic of neonatology research. In recent years, researchers have shifted more focus from neurons themselves to perineuronal cells and intercellular interactions. As a member of the nervous system network, astrocytes are one of the dominant glial cells that regulate ion homeostasis, blood flow, and antioxidant function in the brain. Their changes in molecular mechanisms (e.g., alterations in RNA regulatory networks) during brain injury storms deserve further attention. Non-coding RNAs participate in and promote reactive pathophysiologic changes in astrocytes. The review summarizes and discusses the role of non-coding RNAs in astrocytes in recent years in studies of neonatal brain injury. It focuses on the most studied disease-related ncRNAs: miRNAs, lncRNAs and circRNAs, and hopes to provide possible directions for pathophysiological studies and therapeutic approaches of neonatal brain injury.

Abstract: Safety issues related to the electrification of more electric aircraft (MEA) need to be addressed because of the increasing complexity of aircraft electrical power systems and the growing number of safety-critical sub-systems that need to be powered. Managing the energy storage systems and the flexibility in the load-side plays an important role in preserving the system’s safety when facing an energy shortage. This paper presents a system-level centralized operation management strategy based on model predictive control (MPC) for MEA to schedule battery systems and exploit flexibility in the demand-side while satisfying time-varying operational requirements. The proposed online control strategy aims to maintain energy storage (ES) and prolong the battery life cycle, while minimizing load shedding, with fewer switching activities to improve devices lifetime and to avoid unnecessary transients. Using a mixed-integer linear programming (MILP) formulation, different objective functions are proposed to realize the control targets, with soft constraints improving the robustness of the model. Besides, an evaluation framework is proposed to analyze the effects of various objective functions and the prediction horizon on system performance, which provides the designers and users of MEA and other complex systems with new insights into operation management problem formulation.

Tao and Ming (name) or Tao and Yan (language or speech) is an inseparable pair of important concepts in traditional Chinese language philosophy. In LaoTze’s opinion, Tao could not be spoken out, and language or speech could not reach Tao’s essence. Yan and Tao are separated from each other, and they are paradoxical. All the confusion derives from Yan regardless of how delicate they are. Tao can be expressed in words, but it will never be expressed through common languages. In this article, Tao is regarded as a human being’s thoughts or intentions and is even considered to be the origin of the real world. Language can express people’s thought, although it has some limitations. There exist some contradictions between the real word and the world expressed in words. To enable people to better understand the existence of the real world from multiple perspectives at the language or linguistic level without being constrained by words, this article studies LaoTze’s linguistic philosophy reflected in his opinion on the relationship between Tao and Yan and makes a comparative analysis of modern Western language philosophers’ stand on language (or speech) and existence.

Carpels are a reproductive feature restricted to angiosperms, therefore they are a focus of many botanical studies. However, there are controversies over the nature of carpels. A reason underly-ing these controversies is mixing implications given by conflicting interpretations on fossil carpels in early fossil angiosperms from the Cretaceous. These controversies hinder a clear understanding of angiosperm evolution and systematics. A key to these questions is older fossil fruits bearing concerned information. Here we report a new fossil fruit, Xenofructus dabuensis gen. et sp. nov, from the Middle Jurassic of Liaoning, China. Unlike previously reported fruits of early angio-sperms that were interpreted as bearing seeds either on adaxial or abaxial margin by various au-thors, our fossil demonstrates clearly that the seeds in Xenofructus are neither borne on the adaxial nor abaxial margin of the fruit, instead the seeds of Xenofructus are borne on an axis positioned between two margins. This new feature implies that a placenta in carpels is an ovule/seed-bearing axis, a carpel is a composite organ comprising an enclosing leaf (fruit wall) and an axis (placenta). The adaxial or abaxial position of ovules/seeds frequently seen in fossil and extant angiosperms is a consequence derived through long time evolution (coalescence of placenta with either margin of fruits). Carpels can be taken as foliar structures enclosing their associated ovulate branches.

Autonomous vehicles (AVs) may not only reduce parking demand, but also free up on-street parking spaces. From the perspective of bus priority, converting on-street parking lots into dedicated bus lanes can both ensure bus priority and accommodate non-bus traffic, helping to reduce congestion and pollution. In order to study the impact of conversion of on-street parking lots to bus lanes on traffic flow, a microscopic simulation framework based on VISSIM is proposed in this paper. Data was collected using the floating car method and video recording method to quantify the factors affecting traffic flow due to the conversion of on-street parking. The VISSIM simulation model was then calibrated. According to the proportion of the on-street parking lots into a bus lane, the on-street parking lots conversion simulation model of different scenarios was established, and the influence of different on-street parking lots conversion ratio on traffic efficiency and pollution emission was quantitatively analyzed. Finally, the optimization method based on bus lane network connectivity is discussed. The results indicate that: When the on-street parking lots conversion ratio is approximately 100%, bus speed increases by 21.03%, bus delays decrease by 14.27%, and bus parking instances decrease by 11.31%. Total emissions are negatively correlated with vehicle speed. As the conversion rate of on-street parking increases, the emissions of road segments and the entire road network gradually decrease. At a conversion ratio of 100%, the average total emissions for road segments have the highest reduction rate, decreasing by 4.12%. At a conversion ratio of 50%, the average emission total for the road network shows the largest reduction, falling by 2.88%.

It is expected that scholars will continue to strengthen the depth and breadth of theoretical research on RIS, so as to provide a higher theoretical upper bound for the engineering application of RIS. While making breakthroughs in academic research, great progress has been made in engineering application research and industrialization promotion. This article will provide an overview of RIS engineering applications, mainly including the typical features, typical classifications, and typical deployment scenarios of RIS. Then the challenges and candidate solutions of the RIS are systematically and deeply analyzed, involving the cascade channel decoupling for solving the RIS beamforming, the influences and solutions of RIS regulation constraints, RIS system architecture of network controlled mode, the integrated channel regulation and information modulation, TDD mechanism used for RIS. Future trends and challenges are also provided.

In this work, the Ni/Ti/Nb multilayer composite was successfully manufactured by accumulative pack-roll bonding. The microstructure evolution and mechanical properties of the composite during the accumulative roll bonding (ARB) process were investigated by scanning electron microscopy(SEM), energy dispersive spectrometer(EDS), transmission electron microscopy (TEM), micro-hardness and tensile tests. The results showed that after 5 passes of the ARB process, the deformations of layers were relatively uniform, and no large number of interlayer fractures occurred. The microstructures of Ni and Ti were both equiaxed grains with a grain size of 200 nm and 150 nm, respectively, and finer equiaxed grains of the Ni layer were observed at the interface. The laminar structure of Nb layer was observed. The tensile strength and micro-hardness increased significantly as the number of ARB increased. After 5 passes of the ARB process, the tensile strength of the composite reached 792.3 MPa, and the micro-hardness of Ni, Ti, and Nb were increased to 270.2, 307.4, and 243.4 HV, respectively.

Questions：SAP in mountainous cities of China serve as crucial carriers for species and wild food, constituting potential green infrastructure. These patches should be recognized as locally specific resources. This study investigates the transformation characteristics of the landscape patterns of SAP, along with their elements, across urban-rural gradients, providing foundational support for the planning of conservation and utilization strategies. Location: Yongchuan area of Chongqing in southwest China. Methods: The study investigated urban-rural gradient-based transformation of SAP. A four-direction transect space was selected and divided into uniform sample squares. Fragstats 4.3 calculated the landscape index of SAP, and Spearman correlation coefficients in SPSS were used to evaluate the influence of landform and artificial factors on agroforestry patch transformation. Results: 1) Patch area (PA), Plaque density (PD), and CLUMPY of SAP systematically transform, showing increased SAP areas and higher connectivity with greater distance from the city, resulting in reduced patch fragmentation. However, Edge density (ED) and Largest plaque index (LPI) exhibit irregular transformation patterns. 2) With increased distance from the city, woodland patch area and connectivity increase, leading to decreased fragmentation, dispersal, and lower fractal dimensions. Conversely, Cultivated land follows the opposite trend. garden land patch area, fractal dimension, fragmentation, and dispersal all increase, while connectivity decreases. 3) Landscape pattern transformations of SPA are significantly influenced by artificial factors. Woodland patches are influenced similarly by landform and artificial factors. In contrast, cultivated land and garden land patches are more significantly impacted by artificial factors. Conclusions: SAP exhibit differentiated conservation and utilization measures across urban-rural gradients. Small patches located far from urban centers may benefit from systematic conservation measures to prevent further fragmentation and erosion in peri-urban areas.

As traditional supply chains face increasingly severe environmental issues and countries promote green development and sustainable development policy concepts, cultivating green supply chain operation models is gradually being highly valued by current governments and enterprises. Generally speaking, the production of green products incurs higher additional costs and thus their total production costs also increase. In this work, the product green level is related to the random demand. Under the green supply chain buy-back contract with the green product R&amp;D cost sharing between the manufacturer and the retailer, both the product green level and the order quantity need to be decided to maximize the channel profit. In order to coordinate the green supply chain, the manufacturer needs to share both the risk of good salvage and the green product R&amp;D cost with the retailer. We find that both the wholesale price and buy-back price increase in the manufacturer’s proposition of the green product R&amp;D cost, but decrease in emission reduction efficiency coefficient or carbon trading price. In addition, the product green level, the optimal order quantity and the channel profit increase in emission reduction efficiency coefficient, but decrease in the R&amp;D cost coefficient of the product green level. Interestingly, we find that if the carbon trading price is low, the manufacturer will set a low product green level and the product carbon emission trading is a cost for the supply chain. The increment of the carbon trading price leads to a higher cost such that the channel profit is decreased. However, if the carbon trading price is high, the manufacturer will set a high product green level and the product carbon emission trading is a revenue for the supply chain. The increment of the carbon trading price leads to a higher revenue such that the channel profit is increased.

Semantic communication is not obsessed with improving the accuracy of transmitted symbols, but is concerned with expressing the desired meaning that the symbol sequence exactly carried. However, the generation and measurement of semantic messages are still an open problem. Expansion combines simple things into complex systems and even generates intelligence, which is consistent with the evolution of the human language system. We apply this idea to semantic communication system, quantifying and transmitting semantics by symbol sequences, and investigate the semantic information system in a similar way as Shannon did for digital communication systems. This work was the first to propose the concept of semantic expansion and knowledge collision, which may provide a new paradigm for semantic communications. We believe that expansion and collision will be the cornerstone of semantic information theory.

The Goldbach Conjecture, which is frequently termed as “1 + 1”, has been a fascinating goal for many mathematicians over centuries. A Chinese mathematician, Dr. Jingrun Chen, proved 1 + 2, which is a great success and the best result so far achieved. Although there were several attempts proving the conjecture, these attempts are either tediously long, complicated, or logically imperfect, thus not widely accepted. Taking advantage of the periodicity of primes, here the author provides a straight forward rigorous proof for the Conjecture.

The popularity and growth of additive manufacturing(AM) in recent years are due to its ability to provide innovative solutions to complex manufacturing challenges and its potential to transform the way products are designed, developed, and produced. In this work, the numerical simulation geometry of the model extruder from nozzle is established along with the material extrusion process. The high gravity material extrusion system (HG-MEX) properties and characteristics during filament fabrication are evaluated. This work investigates the effects of gravity on the material extrusion process from nozzle extrusion. This work is unique in the incorporation of fluid surface characteristics to represent the performance and contact with the material extrusion in additive manufacturing. The use of simulation in high gravity material extrusion in additive manufacturing is a meaningful and valuable approach to improving the quality and efficiency of the process.

Remote sensing technology is crucial for accurate rooftop detection, benefiting urban planning, disaster management, and solar resource estimation. This study employs Efficient Interactive Segmentation (EISEG) to enhance the efficiency of remote sensing image labeling, with a particular focus on rooftop detection. It is necessary to use modern technology because traditional manual labelling methods are labor-intensive and complicated. The study introduces a novel framework on deep learning semantic segmentation models, facilitating an efficient approach to rooftop identification using high-resolution UAV remote sensing datasets. Large dataset of labeled UAV rooftop building images, in which each superpixel region is assigned a binary label indicating rooftop presence. Advanced methods including Asymmetric Neural Network (ANN), Dual At-tention Network (DANet), PP-LiteSeg, and Deeplab3 are implemented for automatic rooftop detection due to their higher performance and advanced architectures. These models are executed on the Baidu deep learning platform PaddlePaddle, generating initial rooftop segmentation maps crucial for estimating photovoltaic resources. The ANN model emerges with the highest accuracy at 96%, followed by DANet at 95.09%, PP-LiteSeg at 94.54%, and Deeplab3 at 81.61%. The outcomes presenting efficient models for automated rooftop identification, and demonstrating the continuous need for improving deep learning techniques in smart and sustainable cities.

This study empirically examines the spatial spillover effect of various environmental regulations on green technology innovation using panel data from 284 county-level cities in China between 2007 and 2019. A geographical-economic spatial weight matrix is constructed, and the spatial Durbin model is employed to identify the specific characteristics of this spillover effect. The findings indicate that the spatial spillover effect of green technology innovation primarily occurs through geographical transmission. However, there is no significant spatial autocorrelation when using the economic distance weight matrix. Various types of environmental regulations influence the spatial spillover effect of green technology innovation in distinct ways. Specifically, Market-motivated environmental regulation exhibits a U-shaped relationship with the spatial spillover effect, while Command-controlled environmental regulation demonstrates an inverted U-shaped relationship, suggesting a complementary effect. Additional research shows that the upgrading of industrial structure acts as a mediator between command environmental regulation and the spatial spillover effect of green technology innovation. Government departments should comprehensively coordinate Market-motivated environmental regulation and Command-controlled environmental regulation, accurately assess the intensity of Command-controlled measures, and prevent the migration of green technology innovation elements caused by excessive regulatory measures within enterprises.

MCrAlX (M: Ni or Co or both, X: minor elements) coatings have been widely used to protect hot components in gas turbines against oxidation and hot corrosion at high temperatures. Understanding the influence of the X-elements on oxidation behaviour is important in the design of durable MCrAlX coatings. In this study, NiCoCrAlX coatings doped with Y+Ru and Ce, respectively, were deposited on Inconel-792 substrate by HVOF. The samples were subjected to isothermal oxidation test in laboratory air at 9000, 1000, 1100 ºC and cyclic oxidation test between 100 ºC and 1100 ºC with 1 hour dwell time at 1100 ºC. It was observed that the coating with Ce shows a much higher oxidation rate than the coating with Y+Ru under both isothermal and cyclic oxidation tests. Besides, β-depletion due to interdiffusion between coating and substrate was significantly lower with Ru addition. Simulations results using both a moving phase boundary model and an established oxidation-diffusion model show that Ru stabilize β grains which reduces β-depletion of coating due to substrate interdiffusion. This paper presents a comprehensive study of the influence of Ce and Ru on oxidation behaviour including investigation of the microstructure evolution influenced by oxidation time at coating surface and coating-substrate interface combining experiment and simulation results.

Regional Climatic Comfort Index (CCI) deteriorated significantly due to the climate change and anthropogenic interference. Knowledge regarding the long-term temporal dynamics of CCI in typical regions should be strengthened. In this study, we analyze the temporal and spatial evolution of CCI from 1969 to 2018 in Guangdong Province, based on meteorological indicators, including heat, humidity, wind and cloth loading etc.. Additionally, the population exposure to climate unconformity was examined since 1990 with the help of population data. Our study found that: (1) the warming and humidifying of the summer climate served as the main driving force for the continuous deterioration of CCI, with the comfortable days decreased by 1.06d/10a and the extremely muggy days increased by 2.83d/10a; (2) spatially, the lowest climate comfortability concentrated in southwestern Guangdong with more than 50 uncomfortable days each year, while the climate comfortability in northeastern Guangdong tends to deteriorated whit higher rate, which can reach as high as 6d/10a; (3) in summer, the population exposure to uncomfortable climate highly centralized in the Pearl River Delta, Shantou, Jieyang, and the surrounding areas, and both area and population exposure showed increasing trends. Particularly, Shenzhen held the highest growth rate of population exposure with an increase rate of 2.94 million/10a; (4) although the discomfort distribution and deterioration rate vary across the province, the spatial heterogeneity of comfortability is diminishing in Guangdong Province. This study will provide scientific reference for regional urban planning, thermal environment improvement, local resident health risk analysis, and key strategy implementation, etc.

This paper studies the pilot control strategy and workload of tilt-rotor aircraft dynamic conversion procedure between helicopter mode and fixed-wing mode. A nonlinear flight dynamics model of tilt-rotor aircraft with full flight modes is established. On this basis, a nonlinear optimal control model of dynamic conversion is constructed, considering factors such as conversion corridor limitations, pilot control, flight attitude, engine rated power, and wing stall effects. To assess pilot workload, an analytical method based on wavelet transform is proposed, which examines the mapping relationship between pilot control input's amplitude, constituent frequencies, and control tasks. By integrating the nonlinear optimal control model and the pilot workload evaluation method, the analysis of pilot control strategy and workload during the conversion procedure is conducted, leading to the identification of strategies to reduce pilot workload. The results indicate that incorporating the item of pilot workload in the performance index results in a notable reduction in the magnitude of collective stick inputs and longitudinal stick inputs. Moreover, it facilitates smoother adjustments in altitude and pitch attitude. Additionally, the conversion of the engine nacelle can be achieved at a lower and constant angular velocity. In summary, the conversion and reconversion procedures are estimated to have a low workload (Level 1 ~ Level 2), with relatively simple and easy manipulation for the pilot.

Purpose：Herein, aimed to explore routines to improve students' physical health.Methods:We explored the integration of extracurricular fitness running "Lerun" into college physical education curriculum. Firstly, experimental and the referring groups were selected by experimental method, in which only the experimental group was intervened in combination with extracurricular fitness running "Lerun". After two experiments, the experimental and referring groups were compared in terms of physical fitness (speed, strength, endurance, flexibility, explosive force, etc.), sports skills, body shape, cardiopulmonary function, etc. Results:After T-test, significant differences (p<0.05) between these two groups prove that the students' physical health status of experimental group is better than that of the referring group. Conclusion：It manifests that integrating extracurricular fitness running "Lerun" into college physical education curriculum is an effective means to improve students' physical health.

A space charge density wireless measurement system based on the idea of distributed measurement is proposed for collecting and monitoring the space charge density in an ultra-high-voltage direct-current (UHVDC) environment. The proposed system architecture is composed of a number of wireless nodes connected with space charge density sensors and a base station. The space charge density sensor based on atmospheric ion counter method is elaborated and developed, and the ARM microprocessor and Zigbee radio frequency module are applied. The wireless network communication quality and the relationship between energy consumption and transmission distance in the complicated electromagnetic environment is tested. Based on the experimental results, the proposed measurement system demonstrates that it can adapt to the complex electromagnetic environment under the UHVDC transmission lines and can accurately measure the space charge density.

A lignin modified salt resistance branched high-performance water reducer was prepared via free radical polymerization. The water reducing agent was identified through Fourier transform infrared analysis, thermal gravimetric analysis, and scanning electron microscopy. The experiment conducted on cement paste demonstrates that the water-reducing efficiency can reach a maximum of 44%. Additionally, the significant spatial steric hindrance of the application enhances the dispersal capability of the water-reducing agent, resulting in effective water reduction and reduced viscosity. In addition, its compressive strength is the highest after 3-day curing and 3, 7, 28-day standard curing, and it has the best overall performance both in water and saline water prepared systems.The application in oil cement slurry shows that it exhibits good dispersibility in fresh water, saline water, and substitute ocean water. In the Halfaya and Missan Oilfields of Iraq, BHPWR was used in slurry with a density of 2.28g cm-3 for casing the 244.5 mm salt paste layer of five wells. Cementing results exceeded expectations with over 85% excellent and 100% qualified.

Facing the charging difficulties of free-floating shared electric vehicle and the high cost of mobile charging for single demand, this article proposes a collaborative charging planning method based on the complementary advantages of fixed charging stations and mobile charging vehicles, which can charge shared electric vehicles more efficiently and reduce the charging cost at the same time. A bi-level programming model for fixed and mobile cooperative charging is constructed. The upper level of the model is the minimization model of system charging total cost, seeking the optimal charging scheme and the number of mobile charging vehicles. The lower model is a fixed and mobile cooperative charging path planning model, which calculates the optimal routes for mobile charging vehicles and the shared electric vehicles that need to be transferred to the fixed charging station. The example results show that the cost of the proposed fixed-mobile cooperative charging scheme is reduced by 12.6% compared with the pure fixed charging scheme and 14.9% compared with the pure mobile charging scheme

The potential effect of implementing environmental regulations on economic growth is a controversial issue for a long time. As portrayed by Porter hypothesis, environmental regulations may impact on economic growth by reconstructing the economic structure. A number of previous literature proved the connections between the above three parties. With the intention of exploring the nature of this mechanism, it is important to understand the internal inter-relation of the three parties, requiring data from a large economy experiencing the transition in economic structure. By constructing a panel containing data from 30 Chinese provinces over 10 years (2008-2019), this paper investigate the dynamic inter-relation of the three parties by introducing PVAR model with Granger Test. Results reveal that environmental regulations give a “U” shaped impact to economic growth. In return, economic growth promotes the development of economy with a weakening strength. In addition, results also support the hypothesis that economic structure is the intermediate of economic growth and environmental regulations. There is a rooftop for the effect of economic structure to environmental regulations. The rooftop may signify the best optimization of primary structure.

Background: There is considerable evidence to support the association between environmental tobacco smoke (ETS) exposure and children’s burden of disease. However, literature on the health outcomes of prenatal ETS exposure among Chinese children has not yet been comprehensively reviewed. Objective: This systematic scoping review examines the currently available evidence and identifies gaps for further research on the health consequences of prenatal ETS exposure among Chinese children. Methods: Following the JBI scoping review methodological framework, we conducted a computer-aid search of three electronic databases-- PubMed, EBSCOhost, and ProQuest to include studies from January 2011 to May 2023 that addressed the health outcomes of Chinese children whose mothers were exposed to ETS at any stage of the pregnancy. Further, a methodological quality assessment of the selected articles was conducted, using JBI Critical Appraisal Checklists. Results: A total of 30 articles were reviewed, including eleven high-quality studies and nineteen moderate-quality studies. Five main themes, including hypertension, foetal and children’s development, behavioural disorders, respiratory outcomes, and other health outcomes. Majority of studies showed positive link between prenatal ETS exposure and increase risk of preterm birth, and moderately, foetal growth restriction. Few studies explored other potential adverse outcome of ETS, including hypertension, respiratory morbidity, lung function and asthma in their children. Conclusion: The current available evidence on prenatal ETS exposure in Chinese children has unveiled a wide range of health outcomes, including preterm birth, foetal development, behavioural disorders and much more. However, Chinese studies in this area are still lacking and a gap still exists in relation to the strength of association between prenatal ETS exposure and some health risks. Efficient anti-smoking policies and smoking cessation programs should be developed to promote maternal and child health. Further research is also needed to provide better evidence in this field.

The human serotonin transporter (hSERT) terminates neurotransmission by removing serotonin from the synaptic cleft, which is an essential process plays an important role in depression. In addition to substrate serotonin, hSERT is also the target of drugs of abuse like cocaine and clinically used antidepressants such as escitalopram and paroxetine. To date, few studies attempt to investigate the unbinding mechanism underlying the orthosteric and allosteric modulation of hSERT. The high-resolution X-ray structure of hSERT resolved recently enables us to theoretically study the unbinding of the above four ligands against the S1 or S2 site of hSERT, by means of molecular docking, molecular dynamics (MD) and potential of mean force (PMF) simulations. We proved that for either the S1 or S2 site, the other three ligands (cocaine, escitalopram and paroxetine) are much more favorable than the original substrate serotonin, whether in kinetics along the unbinding pathways or in thermodynamics at the equilibrium states. Furthermore, the S1 site is much more favorable than the S2 site, for each ligand. Interestingly, inspection revealed that there are ~ 3Å lengths between the allosteric site of serotonin and cocaine, and an unseen un-binding pathway for escitalopram at the S1 site except for verification of the broadest trail.

In recent years, electroencephalogram (EEG) emotion recognition has emerged as a research hotspot in the field of artificial intelligence (AI). Despite advancements in EEG-based emotion recognition, room for enhancing performance persists due to EEG signal redundancy and limitations in feature extraction, leading to inefficient models and emotional information loss. To fully utilize EEG's emotional information and improve recognition accuracy while reducing computational costs, this paper proposes a Convolutional-Recurrent Hybrid Network with a dual-stream adaptive approach and an attention mechanism (CSA-SA-CRTNN). Firstly, the model utilizes a CSAM module to assign corresponding weights to EEG channels. Then, an adaptive dual-stream convolutional-recurrent network (SA-CRNN and MHSA-CRNN) is applied to extract local spatial-temporal features. After that, the extracted local features are concatenated and fed into a temporal convolutional network with a multi-head self-attention mechanism (MHSA-TCN) to capture global information. Finally, the extracted EEG information is used for emotion classification. We conducted binary and ternary classification experiments on the DEAP dataset, achieving 99.26% and 99.15% accuracy for arousal and valence in binary classification, and 97.69% and 98.05% in ternary classification, surpassing relevant algorithms. Additionally, the model's efficiency is significantly higher than other models, achieving better accuracy with lower resource consumption.

3D object detection is essential for an accurate and reliable autonomous driving system. Currently, the methods used by the state-of-the-art two-stage detectors are not flexible enough and their fea-ture extraction capabilities are very limited to cope effectively with the disorder and irregularity of point clouds. In this paper, we combine the advantages of both PV-RCNN and PAConv (Position Adaptive Convolution) to create a completely new network, FANet, in order to overcome the ir-regularity and disorder of point clouds. The convolution in our network builds convolutional ker-nels from a basic weight matrix, whose combined coefficients are learned adaptively by LearnNet from relative points. This network allows for flexible modeling of complex spatial variations and geometric structures in the 3D point cloud, enabling better extraction of point cloud features and producing high-quality 3D proposal boxes. Compared to other methods, FANet is superior in terms of 3D object detection accuracy. Extensive experiments on the KITTI dataset have shown a signif-icant improvement in our approach.

The Subtropical Front (STF) plays a key role in the ecology of Chilean jack mackerel Trachurus murphyi. Nonetheless, there are few remote sensing studies of the STF in the open Southeast Pacific Ocean, and almost all of them have been conducted by satellite oceanographers in Russia and Ukraine to support respective large-scale fisheries of jack mackerel in this region. We reviewed these studies that documented long-term seasonal and interannual variability of the STF from sea surface temperature (SST) and sea surface height (SSH) data. We also mapped the STF from satellite sea surface salinity (SSS) data of the SMOS mission (2012-2019). The Subtropical Front consists of two fronts -- North and South STF about 500 km apart -- that border the Subtropical Frontal Zone (STFZ) in-between. The STF is density-compensated, with spatially divergent manifestations in temperature and salinity. In the temperature field, the STF extends in the WNW to ESE direction in the Southeast Pacific. In the salinity field, the STFZ appears as a broad frontal zone, extending zonally between 30-35°S across the entire South Pacific. Three major types of satellite data – SST, SSH, and SSS – can be used to locate the STF. The SSH data is most advantageous with regard to the jack mackerel fisheries owing to the all-weather capability of satellite altimetry and the radical improvement of the spatial resolution of SSH data in the near future. Despite the dearth of dedicated in situ studies of the South Pacific STFZ, there is a broad consensus regarding the STFZ being the principal spawning and nursing ground of T. murphyi as well as a major migration corridor between Chile and New Zealand.

The European Union Water Framework Directive (2000/60/EC; WFD) aims to achieve a good ecological and chemical status of all bodies of surface water by 2027. The development of an integrated guidance on surface water chemical monitoring (e.g. WFD Guidance Document No. 7/19) has been transferred into national German law (Ordinance for the Protection of Surface Waters, OGewV). For the majority of compounds, this act requires a monthly sampling frequency to assess the chemical water quality status of a surface water body. To evaluate the representativeness of the sampling strategy under the OGewV, high-frequency online monitoring data is investigated under different sampling scenarios and compared with current, monthly grab sampling strategy. About 23 million data points were analyzed for this study, three chemical parameters (dissolved oxygen, nitrate-nitrogen, chloride concentration) and discharge data were selected from four catchment of different sizes ranging from 51391 km² to 84 km² (Elbe, Vereinigte Mulde, Neiße and two stations at Lockwitzbach). In this paper we proposed short-term online-monitoring (STOM) as a sampling alternative. STOM considers the placement of online sensors over a limited duration and return interval. In general we: (I) compare the results of conventional grab sampling with STOM, (II) investigate the different performance of STOM and grab sampling using discharge data as proxy for analyzing event-mobilized pollutants and (III) investigate the related uncertainties and costs of both sampling methods. Results show, that STOM outperforms grab sampling for parameters where minimum/maximum concentrations are required by law as the probability to catch a single extreme value is higher with STOM. Furthermore, parameters showing a pronounced diurnal pattern, like dissolved oxygen, are also captured considerably better. The performance of STOM showed no substantial improvements for parameters with small concentration variability, as nitrogen-nitrate The analysis of discharge events as a proxy parameter for event-mobilized pollutants proved that the probability of capturing samples during events is significantly increased by STOM.

Background: The seasonal variation of peptic ulcers is a rhythmic phenomenon reported worldwide, exhibiting diverse patterns and controversies. Unfortunately, it has remained an unresolved mystery for more than 90 years. Numerous studies have found that this phenomenon was closely associated with multiple environmental factors, but the underlying mechanism has never been elucidated. Objectives: This study aims to elucidate the seasonal variation of peptic ulcers and identify the role of environmental factors in the disease. Methods: Based on a recently identified etiology of peptic ulcers, two inverse operations in calculus, differentiation and integration, are iterated to analyze the existing data. First, the fluctuation curve in the seasonal variation is differentiated twice into the monthly incidences caused by multiple individual environmental factors, and the fluctuation curve due to each individual environmental factor is generated separately. Second, the monthly incidences caused by the individual environmental factors are integrated twice to reproduce the fluctuation curves in the seasonal variation of peptic ulcers. Results: The differentiations of the fluctuation curves in the season variation reveal a parallel relationship between the psychological impacts of each individual environmental factor and the monthly incidences of peptic ulcers. The integrations of the monthly incidences caused by 3 environmental factors reproduce the fluctuation curves in 3 representative seasonal patterns of peptic ulcers but make the parallel relationships invisible. Discussion: The parallel relationships revealed a causal role of environmental factors in peptic ulcers, whereas the reproduction of the fluctuation curves elucidated that multiple environmental factors cause the seasonal variation of peptic ulcers by Superposition Mechanism. The regional differences in environmental factors result in the diverse patterns, as well as the controversy questioning the seasonality of peptic ulcers. Significantly, the data analyses exemplify the application of a new concept, Superposition Mechanism, which might be an indispensable methodological complement to life science and medicine.

Background: In 1962, Susser and Stein observed that the mortality rates of peptic ulcers in England and Wales increased markedly in the 1910s, maintained at a high level during the 1910s-1940s, and began to decline steadily since the early 1950s. They termed this epidemic pattern a birth-cohort phenomenon, but its mechanism has never been elucidated. Susser and Stein speculated that the occurrences of extraordinary social environmental factors roughly fit the fluctuations, but the role of environmental factors in peptic ulcers has never been identified. Objectives: This study aims to elucidate the mechanism of the birth-cohort phenomenon of peptic ulcers and identify the role of environmental factors in the disease. Methods: Starting from an etiology identified recently, this study uses the two inverse operations in calculus, differentiation, and integration, to analyze the existing data. First, a fluctuation curve in the birth-cohort phenomenon is differentiated into multiple annual mortality rates caused by individual environmental factors. Second, these annual mortality rates are integrated to reproduce the fluctuation curve in the birth-cohort phenomenon. Results: The differentiation reveals a parallel relationship between the psychological impacts of environmental factors and the mortality rates of peptic ulcers, whereas the integration reproduces a representative fluctuation curve in the birth-cohort phenomenon. The successive occurrences of multiple social environmental factors from the 1910s to 1940s maintained the increase in mortality rates, while the sustained improvements in living environments explained the steady decline of the mortality rates from the early 1950s. Conclusion: The parallel relationship suggests a causal role of environmental factors in peptic ulcers, whereas the reproduction of a representative fluctuation curve indicates that multiple environmental factors caused the birth-cohort phenomenon by Superposition Mechanism. Significantly, this study challenges the current reductionist approach used to study disease in modern medicine by demonstrating the effectiveness of an opposite methodological concept focused on integration.

The Connor–Davidson Resilience Scale (CD-RISC) and the Brief Resilience Scale (BRS) are two widely used scales to measure resilience. Although both scales seek to assess an individual’s ability to recover from and adapt to disruptions or stressful events, they may capture different aspects of resilience. While the CD-RISC focuses on resources that can help individuals recover from and adapt to disruptions or stressful events, the BRS directly measures one’s ability to bounce back or be resilient. The aim of this study is to empirically examine the differences between the CD-RISC and the BRS. Two samples (n = 202, 246) consisting of undergraduate students from Taiwan were used. The results of confirmatory factor analysis show that the CD-RISC and the BRS are highly correlated but still distinct. The results of regression analyses show that the CD-RISC and the BRS have unique predictive effects on depression and life satisfaction. The research findings suggest that the CD-RISC and the BRS capture different aspects of resilience. For future research on resilience, researchers should pay attention to the differences between these scales and choose the one that most closely fits their research purpose.

With the rapid development of network science, Turing pattern on complex networks has attracted extensive attention from researchers. In this paper, we focus on spatial patterns in multiplex ER (Erdös-Rényi) random networks, taking the predator-prey model with Allee effect and hyperbolic mortality as an example. In theory, the threshold condition for generating Turing pattern is given using the Turing instability theory of multiplex networks. Numerically, we design relevant experiments to explore the impact of network topology on Turing pattern. The factors considered include model parameters, diffusion rate, average degree of the network, and differences in the average degree of different layers. The results indicate that the importance of diffusion rate and network average degree for Turing pattern is affirmed on the single-layer network. For multiplex networks, the differentiation of average degrees in different layers controls the generation of Turing pattern, which is not affected by the diffusion rates of the two populations. More interestingly, we observe the switching of Turing pattern and spatiotemporal pattern. We believe that these findings contribute to a better understanding of self-organization on complex networks.

Loess is a special soil with high water sensitivity, which covers a large area in northwest China. Cracks are prone to generate in loess under the arid and semi-arid climate, which will provide the preferential channel for water and reduce the mechanical properties of soils. It is of great significance to understand the evolution characteristics and mechanisms of the cracks in loess areas. At present, the researches on cracks in soils are mainly concentrated in the characteristics of different cracking patterns. However, the spacing cracks are mostly discussed in materials like rock and concrete, rather than soils. The cracking characteristics and mechanisms of spacing cracks in loess is still inadequate. In this research, the drying tests of loess are carried out with different sizes of specimens. The parameters of spacing cracks and local strain distributions of the loess samples are obtained via PCAS and DIC methods during desiccation, respectively. The cracking modes, space cracking laws like insertion and saturation of spacing cracks are revealed. Finally, the size effect on the characteristics of spacing cracks is verified with a discrete element software MatDEM.

The e-commerce platform in the digital economy era has evolved into a data platform ecosystem built around data resources and data mining technology systems. The most typical applications of big data are also concentrated in the field of e-commerce. E-commerce companies should first grasp the interactive relationship among the three major factors of data, technology and innovation, e-commerce platform operation is a multidisciplinary research field. It is not easy for researchers to obtain a panoramic view of the knowledge structure in this field. Knowledge graph is a kind of graph that shows the development process and structure relationship of knowledge with the field of knowledge as the object. It is not only a visual knowledge mapping, but also a serialized knowledge pedigree, which provides researchers with a quantitative research method for the development trend of statistics and academic status. The purpose of this research is to help researchers understand the key knowledge, evolutionary trends and research frontiers of current research. This study uses Citespace bibliometric analysis to analyze the data of the Science Net database and finds that: 1) The development of the research field has gone through three stages, and some representative key scholars and key documents have been recognized; 2) the common knowledge mapping of literature The co-occurrence of citations and keywords shows research hotspots; 3) The results of burst detection and central node analysis reveal research frontiers and development trends. Today, the visualization of big data brings different challenges. The abstraction between the world and today's data visualization occurs when the data is captured. Every user sees his own visualization data generated by standardized calculations. At the same time, there are still many controversies in the theoretical model, structure and structural dimensions. This is the direction that future researchers need to further study.

Based on a rich data set of recoveries donated by a debt collection business, recovery rates for non-performing loans taken from a single European country are modelled using linear regression, linear regression with Lasso, beta regression and inflated beta regression. We also propose a two-stage model: beta mixture model combined with a logistic regression model. The proposed model allows us to model the multimodal distribution we find for these recovery rates. All models are built using loan characteristics, default data and collections data prior to purchase by the debt collection business. The intended use of the models is to estimate future recovery rates for improved risk assessment, capital requirement calculations and bad debt management. They are compared using a range of quantitative performance measures under K-fold cross validation. Among all the models, we find that the proposed two-stage beta mixture model performs best.

Tulou dwellings in Southeast China have captivated global interest due to their distinctive appearance, sustainable construction materials and technologies, and their defensive and collective housing functions. Despite several recognized as World Cultural Heritage sites, the vast majority of tulou buildings are undergoing irreversible decline and destruction, necessitating a comprehensive and systematic study. Taking 83 Tulou buildings in Raoping County, Chaozhou City, Guangdong Province as the research object, this study reconstructs the historical scenes and systematically reveals the emergence, popularity, and consolidation process of tulou dwellings as integrated defensive and residential buildings for ordinary people by conducting a comprehensive analysis of historical documents and local chronicles. Based on an extensive field investigation, the study systematically analyzes the geospatial distribution and the spatial characteristics of Raoping tulou and its residential unit. The results demonstrate the adaptability and flexibility of tulou dwellings, showcasing their developmental process and revealing the inclusive nature of these traditional residences, as well as the initiative of those who reside within them. The research findings contribute to a more dynamic, comprehensive, and authentic understanding of tulou and Chinese traditional residences, providing valuable references for the preservation and sustainable development of tulou architectural heritage.

In pattern recognition domain, deep architectures are widely used nowadays and they have achieved fine grades. However, these deep architectures need special demands, especially big datasets and GPU. Aiming to gain better grades without deep networks, we propose a simplified algorithm framework using fusion features extracted from the salient areas of faces. Furthermore, the proposed algorithm has achieved a better result than some deep architectures. For extracting more effective features, this paper firstly defines the salient areas on the faces. This paper normalizes the salient areas of the same location in the faces to the same size, therefore it can gain more similar features from different subjects. LBP and HOG features are extracted from the salient areas, fusion features’ dimensions are reduced by Principal Component Analysis( PCA) and we apply softmax to classify the six basic expressions at once. This paper proposes a salient areas definitude method which uses peak expressions frames to compare with their neutral faces. This paper also proposes and applies the idea of normalizing the salient areas to align the specific areas which express the different expressions. This makes the salient areas found from different subjects have the same size. Besides, gamma correction method is firstly applied on LBP features in our algorithm framework which improves our recognition rates significantly. By applying this algorithm framework, our research has gained state-of-the-art performances on CK+ database and JAFFE database.

Quantifying the landscape pattern change can effectively demonstrate the ecological progresses and the consequences of urbanization. Based on remotely sensed land cover data in 1994, 2000, 2006 and a gradient analysis with landscape metrics at landscape- and class- level, we attempted to characterize the individual and entire landscape patterns of Shanghai metropolitan during the rapid urbanization. We highlighted that a roadscape transect approach that combined the buffer zone method and the transect-based approach was introduced to describe the urban-rural patterns of agricultural, residential, green, industrial, and public facilities land along the railway route. Our results of landscape metrics showed significant spatiotemporal patterns and gradient variations along the transect. The urban growth pattern in two time spans conform to the hypothesis for diffusion–coalescence processes, implying that the railway is adaptive as a gradient element to analyze the landscape patterns with urbanization. As the natural landscape was replaced by urban landscape gradually, the urban fringe expanded radically. The results also showed that the desakota region expanded its extent widely. Satellite towns witnessed the continual transformation from the predominantly rural landscape to peri-urban landscape. Furthermore, the gap between urban and rural areas remained large especially in public service. More reasonable urban plans and land use policies should push to make more of an effort to transition from the urban-rural separation to coordinated urban-rural development. This study is a meaningful trial in demonstrating a new form of urban–rural transects to study the landscape change of large cities from a strategic viewpoint. By combining gradient analysis with landscape metrics, we addressed the process of urbanization both spatially and temporally, and provided a more quantitative approach to urban studies.

In this paper, by evaluating extreme value of the qth-power current, a torque sharing function (TSF) family for reducing the torque ripples in the switched reluctance motor (SRM) is proposed. The optimization criteria of the TSF has two secondary objectives, including the maximization of the torque-speed range and the minimization of copper loss. The evaluation indices in terms of the peak phase current, the rms phase current, and the torque ripple factor are compared between the proposed TSF family and four conventional TSFs including linear, sinusoidal, exponential, and cubic TSFs. An optimization objective function that combines the maximum absolute value of the rate-of-change of the flux linkage (MAV-RCFL) and the qth-power of current is proposed and a weighting factor is used to balance the influence of the two optimization objectives. An optimal TSF can be easily obtained by solving the optimization problem from the TSF family. The proposed TSF is validated by using simulations and experiments with a three-phase 6/4 SRM with 7.5 kW, 3000 rpm, and 270 V DC-link voltage. The dynamic simulation model is implemented in Matlab/Simulink. The results demonstrate the validity and superiority of the proposed control method; the optimal TSF provides better torque-speed performance, and a better reduction in copper loss and torque ripples at high speed compared to the conventional TSFs obviously.

Hemodynamics is the eternal theme of the circulatory system. Abnormal hemodynamics and cardiac and pulmonary development intertwine to form the most important features of children with congenital heart diseases (CHDs), thus determining these children’s long-term quality of life. However, due to the lack of neonatal rodent models of CHDs, it is unclear how CHD-associated hemodynamics shape postnatal cardiac and pulmonary development. Here, we review the varieties of hemodynamic abnormalities that exist in children with CHDs, the recently developed neonatal rodent models of CHDs, and the inspirations these models have brought us in the areas of cardiomyocyte proliferation and maturation, and in alveolar development. Furthermore, current limitations, future directions, and clinical decision-making based on these inspirations are highlighted. Understanding how CHD-associated hemodynamic scenarios shape postnatal heart and lung development may provide a novel path to improving the long-term quality of life of children with CHDs, transplantation of stem cell–derived cardiomyocytes, and cardiac regeneration.

This study mainly experimentally investigates and explores the effects of local low-frequency vibrations on the starting-up and heat transfer characteristics of the pulsating heat pipe. A micro motors with the vibration frequency of 200 Hz were imposed on the external surface of evaporation, condensation and adiabatic section of the pulsating heat pipe, respectively, and the starting-up temperature and the average temperatures along the evaporation section as well as the thermal performances of the vibrating heat pipe were experimentally scrutinized under the local vibrations of different positions. The following important conclusions can be achieved by the experimental study: 1) The effect of vibrations at the evaporation section and at the adiabatic section on the starting-up time of pulsating heat pipe is more significant than that at the condensation section. 2) The vibrations at different positions can reduce the starting-up temperature of the pulsating heat pipe. The effect of the vibrations at the evaporation section is the best as the heating power is lower, and the effect of the vibration at the adiabatic section is the best as the heating power is higher. 3) The vibrations at the evaporation section and at the adiabatic section can reduce the thermal resistance of the pulsating heat pipe. However, the vibrations at the condensation section have little effect on the thermal resistance of the pulsating heat pipe. 4) The vibrations at the evaporation section and at the adiabatic section can effectively reduce the temperature of evaporation section of the pulsating heat pipe, but the vibrations at the condensation section have no effect on the temperature of evaporation section of the pulsating heat pipe.

In wireless sensor networks (WSNs), each sensor node can estimate the global parameter from the local data in distributed manner. This paper proposed a robust diffusion estimation algorithm based on minimum error entropy criterion with self-adjusting step-size, which are referred to as diffusion MEE-SAS (DMEE-SAS) algorithm. The DMEE-SAS algorithm has fast speed of convergence and is robust against non-Gaussian noise in the measurements. The detailed performance analysis of the DMEE-SAS algorithm is performed. By combining the DMEE-SAS with diffusion minimum error entropy (DMEE) algorithms, an Improving DMEE-SAS algorithm is proposed, in non-stationary environment where tracking is very important. The Improving DMEE-SAS algorithm can avoid insensitivity of the DMEE-SAS algorithm due to the small effective step-size near the optimal estimator, and obtain a fast convergence speed. Numerical simulations are given to verify the effectiveness and advantages of these proposed algorithms.

Proteomics research has become one of the most important topics in the fields of life science and natural science. At present, research on protein–protein interaction networks (PPINs) mainly focuses on detecting protein complexes or function modules. However, existing approaches are either ineffective or incomplete. In this paper, we investigate function module detection mechanisms in PPIN, including open databases, existing detection algorithms and recent solutions. After that, we describe the proposed solution based on simplified swarm optimization (SSO) algorithm and gene ontology knowledge. The proposed solution implements SSO algorithm for clustering proteins with similar function, and imports biological gene ontology knowledge for further identifying function complexes and improving detection accuracy. Furthermore, we use four different categories of species dataset for experiment: Fruitfly, Mouse, Scere, and Human. The testing and analysis result show that the proposed solution is feasible, efficient and could achieve a higher accuracy of prediction than existing approaches.

As the COVID-19 pandemic has caused enormous damage to society, economy and public health security, it is crucial to combat the epidemic and allocate social and health resources effectively. Global optimization algorithms are extensively used in many domains to find optimal solutions to complex problems. Thus, a survey of three typical global optimizations applied on the COVID-19 pandemic is timely. This article is structured into three typical global optimization algorithms - Genetic Algorithm, Particle Swarm Optimization, and Cat Swarm Optimization - and summarizes the framework models and practical applications, as well as other optimization methods that may be applied to COVID-19. Finally, current unresolved challenges and future research opportunities to be explored are summarized.

Pandemics caused by viruses have threatened lives of thousands of people. Viral infection is a complex and diverse process, and substantial studies have been complemented in understanding the biochemical and molecular interactions between viruses and hosts. However, the physical microenvironment where infections implement is often less carefully considered, and the role of mechanobiology in viral infection remains elusive. Mechanobiology focuses on sensation, transduction and response to intracellular and extracellular physical factors by tissues, cells and extracellular matrix. The intracellular cytoskeleton and mechanosensors have been proved to be extensively involved in virus life cycle. Furthermore, innovative methods in vivo and in vitro are being utilized to elucidate how extracellular factors including stiffness, forces and topography in regulating viral infection. Our current review covers how physical factors from different sources coordinate virus infection. We further discuss how this knowledge can be harnessed in future research on cross-fields of mechanobiology and virology.

The development of hybrid unmanned aerial underwater vehicles (HAUVs) compatible with the advantages of the aerial vehicles and the underwater vehicles is of great significance. This paper presents the first study on a new HAUV layout using four rotors to realize the medium crossing motion of a transverse slender body similar to the fuselage of a missile or a submarine, that is the hybrid aerial underwater quadrotor (HAUQ). Then a robust control strategy is proposed for the take-off HAUQ on the water in the presence of unknown disturbances and complex model dynamic uncertainties. As a semi-submersible HAUQ rises straightly from the water, the inside of the slender fuselage placed horizontally is filled with water. The center of the mass, the moment of inertia, and the arm of force of the HAUQ will change rapidly in the takeoff phase from the water since the rapid non-uniform change of mass caused by the passive fast drainage. It is difficult to establish a accurate mathematical model of the complex dynamic changes caused by the multi-media dynamics, the fast changing buoyancy, and the added mass crossing air–water surface. Therefore, an uncertain kinematic and dynamic model is established through the passive fast nonuniform change and the complex dynamics are considered as the unknown terms, and the external disturbances of gust and other factors are assumed as the bounded disturbance input. A robust design approach is introduced to deal with the fast time-varying mass disturbance based on the input-to-state stability (ISS) theorem. The complex dynamics are estimated using the basis function and the unknown weight parameters, and the adaptive laws are adopted for the on-line estimation of the unknown weight parameters. Consider the residual disturbance of the uncertain nonlinear system as a total disturbance term, a disturbance observer is introduced for disturbance observation. The numerical simulation shows the feasibility and robustness of the proposed algorithm.

Material identification based on R_value (transparency natural logarithm ratio of low-energy to high-energy) of line-scan dual-energy X-ray transmission (DE-XRT) has a good prospect for industrial application. Unfortunately, the DE-XRT signals before attenuation cannot be directly measured, whereas their precision is very important to R_value. Therefore, a context-based signal synthesis method which takes the filtered signals that remove high-frequency noises and retain low-frequency actual fluctuations as the reference value, and takes into account the vertical (forward/column) direction and horizontal (scanning/row) direction anisotropy of line-scan images was proposed. The vertical is a time series with continuity of signal trend; the horizontal is a spatial characteristic with the fluctuation synchronization within the same row signals. The special synthesis evaluations of curve synthesis difference and surface synthesis difference were also proposed. Experimental results show that the tow evaluations are both only about 0.0007, and it only takes 35 ms to complete the surface synthesis of 119×119 pixels on the CPU with 3.4 GHz main frequency. The presented method can achieve high signal synthesis precision and calculation real-time, so as to facilitate DE-XRT material identification. It can be extended to improve the precision of numerical synthesis in other line-scan uncomplete signals.

Background: Alzheimer's disease (AD) is a leading cause of dementia, significantly influenced by the Apolipoprotein E4 (APOE4) gene and gender. This study aims to use machine learning (ML) algorithms to predict brain age and assess AD risk by considering the effects of APOE4 genotype and gender. Methods: We collected brain volumetric MRI data and medical records from 1100 cognitively unimpaired individuals and 602 AD patients. We applied three ML regression models—XGBoost, Random Forest (RF), and Linear Regression (LR)—to predict brain age. Additionally, we introduced two novel metrics, Brain Age Difference (BAD) and Integrated Difference (ID), to evaluate model performance and analyze the influence of APOE4 genotype and gender on brain aging. Results: AD patients displayed significantly older brain ages compared to their chronological ages, with BADs ranging from 6.5 to 10 years. The RF model outperformed both XGBoost and LR in terms of accuracy, delivering higher ID values and more precise predictions. Comparing APOE4 carriers with non-carriers, the models showed enhanced ID values and consistent brain age predictions, improving overall performance. Gender-specific analyses indicated slight enhancements, with models performing equally well on both genders. It indicates that APOE4 may be a more robust predictor of brain age than gender. Conclusion: Robust ML models for brain age prediction can be pivotal in the early detection of AD risk via MRI brain structural imaging, especially for APOE4 carriers. Such early identification may facilitate timely preventive interventions for AD.

Ce-promoted NiMgAl mixed-oxide (NiCex-C, x = 0, 1,5,10) catalysts were prepared from the quaternary hydrotalcite precursors for CO2 hydrogenation to methane. By engineering the Ce contents, NiCe5-C showed its prior catalytic performance in low-temperature CO2 hydrogenation, being about 3 times higher than that of Ce-free NiCe0-C catalyst (TOF of NiCe5-C and NiCe0-C: 1.19 h-1 vs 0.39 h-1 @ 250 oC). With extensive characterization, it was found that Ce dopants promoted the reduction of NiO by adjusting the interaction between Ni and Mg(Ce)AlOx support. The higest ratio of surface Ni0/(Ni2+Ni0) was obtained over NiCe5-C. Meanwhile, the surface basicity was tailored with Ce dopants. The strongest medium-strength basicity and highest capacity of CO2 adsorption was achieved on NiCe5-C with 5wt% Ce content. The TOF tests indicated a good correlation with medium-strength basicity over the NiCex-C samples. The results showed that the high medium-strength and Ce-promoted surface Ni0 species endows the enhanced low-temperature catalytic performance in CO2 hydrogenation to methane.

In recent years, semantic communication has received significant attention from both academia and industry, driven by the growing demands for ultra-low latency and high-throughput capabilities in emerging intelligent services. Nonetheless, a comprehensive and effective theoretical framework for semantic communication has yet to be established. In particular, finding the fundamental limits of semantic communication, exploring the capabilities of semantic-aware networks, or utilizing theoretical guidance for deep learning in semantic communication are very important yet still unresolved issues. In general, the mathematical theory of semantic communication and the mathematical representation of semantics are referred to as semantic information theory. In this paper, we introduce the pertinent advancements in semantic information theory. Grounded in the foundational work of Claude Shannon, we present the latest developments in semantic entropy, semantic rate-distortion, and semantic channel capacity. Additionally, we analyze some open problems in semantic information measurement and semantic coding, providing a theoretical basis for the design of a semantic communication system. Furthermore, we carefully review several mathematical theories and tools and evaluate their applicability in the context of semantic communication. Finally, we shed light on the challenges encountered in both semantic communication and semantic information theory.

Thin-film lithium niobate has gained significant attention in photonics due to its broad optical transparency, high refractive index, nonlinear coefficient, and substantial electro-optic coefficient. It holds great promise for developing electro-optic modulators with low loss, a compact size, and wide bandwidth. This study focuses on a meticulous investigation utilizing microwave photonics to establish a high-performance electro-optic modulator. Specifically, we analyze the optical mode field distribution and traveling wave electrode structure of lithium niobate thin-film materials. The proposed modulator achieves an impressive half-wave voltage-length product of 1.69 V·cm, a negligible metal loss of 0.01 dB/cm, and a substantial 3dB electro-optic bandwidth of 50 GHz. This research successfully realizes low-loss, high-efficiency LNOI electro-optical modulators, providing a strong foundation for large-scale integrated optoelectronic systems.

Utilizing ecological engineering to manage pests by enhancing the biological control function of natural predators through the selection of high-efficiency bank plants and the establishment of bank plant systems within agricultural ecosystems is an optimal strategy. While bank plant systems have found widespread use in greenhouse crop cultivation, their application in rice fields remains limited. This study aimed to assess the efficacy of Leersia sayanuka as a bank plant for controlling planthoppers and to explore the potential of sesame as a complementary plant to enhance the effectiveness of the bank plant system through field trials. The findings revealed that planting a strip of L. sayanuka, at least 50 cm wide and extending over 1 m in length, had a notable impact on planthopper control in paddy fields. Moreover, the incorporation of Sesamum indicum, a nectar plant, into the bank plant system consisting of L. sayanuka, Nilaparvata muiri, and Anagrus nilaparvatae, led to a significant increase in the population of Anagrus spp. in rice fields. This increase was accompanied by a rise in the egg parasitism rate targeting rice planthoppers, resulting in a marked improvement in overall rice planthopper control in paddy fields. Thus, the combined system demonstrated efficiency as an effective bank plant system for managing rice planthoppers.

As the application of cyber-physical systems (CPSs) becomes more and more widespread, its security is becoming a focus of attention. Currently, there has been much research on the security defense of the physical layer of the CPS. However, most of the research only focuses on one of the aspects, for example, attack detection, security state estimation or recovery control. Obviously, the effectiveness of security defense targeting only one aspect is limited. Therefore, in this paper, a set of security defense processes is proposed for the case that a CPS containing multiple sensors is subject to three kinds of stealthy attacks (i.e., zero-dynamics attack, covert attack, and replay attack). Firstly, the existing attack detection method based on improved residuals is used to detect stealthy attacks. Secondly, based on the detection results, an optimal state estimation method based on improved Kalman filtering is proposed to estimate the actual state of the system. Then, based on the optimal state, internal model control (IMC) is introduced to complete the recovery control of the system. Finally, the proposed methods are integrated to give a complete security defense process, and the simulation is verified for three kinds of stealthy attacks. The simulation results show that the proposed methods are effective.

We propose a computer-generated hologram method for near-eye virtual reality and augmented reality 3D display. A 3D object located near the holographic plane is projected onto a projection plane to obtain a plurality of projected images with different angles. The hologram is calculated by superposition of projected image convolution with a specific PSF through the interference of reference wave with object wave. Holographic 3D display systems with LED as illumination, 4f optical filtering system and lens as eyepiece for near-eye VR display and HOE as combiner for near-eye AR display are designed. The results show that the proposed method is about 38 times faster than the conventional point cloud method. The proposed method is flexible to produce speckle noise free high-quality VR and AR images with efficient focus and defocus capabilities.

Ti and its alloys are the most commonly used materials for biomedical applications. However, bacterial infection after implant placement is still one of the significant rising complications. Therefore, the application of the antimicrobial agents into implant surfaces to prevent implant-associated infection has attracted lots of attention. Scientific papers have shown that inorganic antibacterial metal element (e.g. Ag, Cu, Zn) can be introduced to implant surfaces with the addition of metal nanoparticles or metallic compounds into electrolyte via micro-arc oxidation (MAO) technology. In this review, the effects of the composition and concentration of electrolyte and process parameters (e.g. voltage, current density, oxidation time) on morphological characteristics (e.g. surface morphology, bonding strength), antibacterial ability and biocompatibility of MAO antimicrobial coating were discussed in detail. Anti-infection and osseo-integration can be simultaneously accomplished with the selection of the proper antibacterial elements and operating parameters. Besides, MAO assisted by magnetron sputtering (MS) to endow Ti-based implant materials with superior antibacterial ability and biocompatibility was also discussed. Finally, the development trend of MAO technology in the future was forecasted.

Reinfection with severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) variants due to immune escape challenges the global response to the pandemic. We estimated the Omicron reinfection prevalence among people who had previous SARS-CoV-2 infections in Shanghai, China. We conducted a telephone survey in December 2022 for those who were previously infected with Omicron between March and May 2022. Information on demographics, coronavirus disease 2019 (COVID-19) testing, and vaccination history was collected. The overall and subgroup reinfection rates were estimated and compared. Among the 1981 respondents who were infected between March and May 2022, 260 had positive nucleic acid or rapid antigen tests in December 2022, with an estimated reinfection rate of 13.1% (95% confidence interval [95% CI]: 11.6-14.6). The reinfection rate for those who had a booster vaccination was 11.4% (95% CI: 9.2-13.7), which was significantly lower than that for those with an incomplete vaccination series (15.2%, 95% CI: 12.3-18.1) (adjusted odds ratio [aOR]: 0.579; 95% CI: 0.412–0.813). Reinfection with the Omicron variant was lower among individuals with previous SARS-CoV-2 infection and had completed a booster vaccination, suggesting that hybrid immunity can offer better protection against reinfection with Omicron sublineages.

With the increasing prominence of renewable energy sources providing flexibility to the power grid, there is a growing recognition of the need to expand virtual Energy Storage Systems (ESS) to replace traditional ESS, which faces challenges in terms of supply and scalability. Grid-connected microgrids can supply power stably and are being built, so they can be used as virtual ESS to provide flexibility to the power system. This study proposes an approach to determine the optimal Power Conversion System (PCS) and battery capacity for a Virtual Energy Storage System(VEES) based on a grid-connected microgrid incorporating Photovoltaic (PV) and ESS. In this paper, it is assumed that microgrids can provide flexibility to the grid by participating in the energy trading market, there are corresponding profits and penalties for order. Numerical examples are performed to demonstrate the effectiveness of the proposed method.

Major emergencies can have a devastating impact on society, becoming a catalyst for social disorder and unrest and a trigger for social or political change. In today's world of frequent emergencies, the emergency management capacity of local governments is key to promoting safe operations and maintaining stability in cities and towns. Aiming to explore the direction and focus of local government emergency management capacity building, this paper establishes a local government emergency capacity evaluation system based on the emergency management process and combines Gray-Dematel, a gray decision laboratory analysis method, and AISM, an adversarial explanatory agency model, to derive the importance and intrinsic relationship among emergency capacity indicators. The algorithm describes the importance degree of each indicator in the system and also helps better understand the intrinsic relationship among the indicators. The outcomes of this research can be used to outline directional suggestions for the development of local government emergency response capacity and provide a new theoretical basis for more effective construction of local government emergency response capacity.

In this study, we explore the potential of using a straightforward neural network inspired by the retina model to efficiently restore low-light images. The retina model imitates the neurophysiological principles and dynamics of various optical neurons. Our proposed neural network model reduces the computational overhead compared to traditional signal-processing models while achieving results similar to complex deep learning models from a subjective perceptual perspective. By directly simulating retinal neuron functionalities with neural networks, we not only avoid manual parameter optimization but also lay the groundwork for constructing artificial versions of specific neurobiological organizations.

Focused microwave breast hyperthermia (FMBH) employs a phased antenna array to perform beamforming that can focus microwave energy at targeted breast tumors. Selective heating of the tumor endows the hyperthermia treatment with high accuracy and low side effects. The effect of FMBH is highly dependent on the applied phased antenna array. This work investigates the effect of polarizations of antenna elements on the microwave focusing results by simulations. We explore two kinds of antenna arrays with the same number of elements using different digital realistic human breast phantoms. The first array has all the elements’ polarization in the vertical plane of the breast while the second array has half elements’ polarization in the vertical plane and the other half in the transverse plane, i.e., cross polarization. In total 96 sets of different simulations are performed, and the results show that the second array leads to a better focusing effect in dense breasts than the first array. This work is very meaningful for the potential improvement of the antenna array for FMBH, which is of great significance for the future clinical applications of FMBH. The antenna array with cross polarization can also be applied in micro-wave imaging and sensing for biomedical applications.

China is a traditional agricultural country, and the integration of rural industries has become an essential policy direction for the current strategy of agricultural modernization in China. In recent years, the agricultural industrial chains across various regions of China have consistently expanded and extended. The multifunctionality of agriculture is continuously unearthed, and the principal entities managing agriculture have become increasingly diversified and have grown significantly. New industries and forms in agriculture emerge incessantly. Accurately and profoundly understanding the inherent features of the integration of industries in rural China, establishing a scientific and rational measurement index system in line with the current status and development goals of rural China, and employing appropriate measurement methods to assess its development level and process, is instrumental in comprehending the level of integrated development in various regions. This aids in identifying challenges in the developmental process and proposing targeted developmental strategies. Hence, this paper, rooted in the integration of rural industries, cross-industry, industry extension, industry agglomeration, and industry penetration, sets up an measurement index system. Using provincial panel data from 2011 to 2020, the paper measures the level of integrated development in rural industries across China and its 31 provinces. Based on the measurement results, further techniques such as kernel density estimation and Gini coefficient decomposition have been used to analyze the spatial distribution characteristics and dynamic trends of the integrated development of rural industries in China. Research indicates that during the sample period, the overall level of integrated development in rural industries in various provinces in China has shown an upward trend. Development among the eastern, central, and western regions is highly uneven, but this disparity has been gradually narrowing in recent years. Furthermore, the levels of integrated development in different provinces exhibit significant spatial agglomeration effects. The development level of neighboring regions significantly impacts the province's development status. In the process of integrated development of rural industries in China, there's a trend where "it's easier to downgrade than to upgrade," with very few regions achieving leapfrog development.

Single-phase-to-ground fault in non-effectively grounded systems poses serious public safety concern. Along with increasing deployment of low-voltage (LV) sensors, new opportunities and ways are created for solving this traditional problem in distribution systems. A new approach, identifying primary single-phase-to-ground line fault and locating it through measurement data from smart sensors deployed in the secondary side of distribution transformers, is proposed in this paper. When a fault occurs in primary distribution feeder, the transient aerial mode voltage (AMV) of each LV smart sensor is calculated. The fault line can be identified by an abrupt change value of AMV at LV side. Next, by finding the position of the maximum value of this AMV from LV sensors on the fault line, the fault location can be pinpointed to two neighboring distribution transformers. The proposed method has been proven to be efficient and reliable by simulation studies.

Bipolar neutrosophic set is an important extension of bipolar fuzzy set. This set is a hybridization of bipolar fuzzy set and neutrosophic set. Every element of a bipolar neutrosophic set consists of three independent positive membership functions and three independent negative membership functions. In this paper, we develop cross entropy measures of bipolar neutrosophic sets and prove its properties. We also define cross entropy measures of interval bipolar neutrosophic sets and prove its properties. Thereafter, we develop two novel multi-attribute decision making methods based on the proposed cross entropy measures. In the decision making framework, we calculate the weighted cross entropy measures between each alternative and the ideal alternative to rank the alternatives and choose the best one. We solve two illustrative examples of multi-attribute decision making problems and compare the obtained result with the results of other existing methods to show the applicability and effectiveness of the developed method. In the end, the main conclusion and future scope of research are summarized.

Forests play a pivotal role within the ecological milieu, with alterations to forested areas not only impacting the local environment but also serving as a significant contributing factor to the occurrence of landslide disasters. However, the significance of forests in connection with deep seated landslides is diminished. In instances of extreme events, heavy rainfall, highly weak slopes, or seismic events, it is improbable for forest cover to exert any influence. Due to extensive agricultural irrigation, the Heifangtai terrace of China has experienced a significant rise in groundwater levels, leading to the occurrence of numerous landslides. Through field investigations and remote sensing interpretation, this study has revealed dramatical geomorphological changes in the Heifangtai terrace due to the occurrence of widespread landslides. These changes are likely to disrupt the pre-existing hydrological balance within the study area, thereby altering the conditions for landslides. Therefore, understanding how the evolution patterns of loess landslides can be assessed is a crucial scientific issue for predicting the conditions of landslide occurrence. Taking the evolution of landslides along the edge of the Heifangtai terraces as an example, this study first classified different types of loess landslides. Subsequently, the temporal and spatial distribution characteristics of these landslides were analyzed. Finally, utilizing the FLAC3D software, the stability of the loess slopes at the edge of the Heifangtai terrace was examined under the lateral evolution mode. The research findings indicate that the current loess landslides in the Heifangtai terrace exhibits longitudinal multi-periodicity and lateral group-occurring behavior, which is significant for assessing loess landslides along the edge of Heifangtai terraces.

The purpose of this study is to ascertain whether implementation difficulty can be used in slot allocation model as a new mechanism for slightly weakening grandfather right. According to which, a linear integer programming model is designed to compare and analyze displacement, implementation difficulty and priority with different weights. Test results show that the implementation difficulty can be significantly reduced without causing excessive displacement and disruption of existing priorities, by weight setting while declared capacity is cleared. In addition to this, whether the movements are listed in order of descending priority or not have great impact on displacement and implementation difficulty within slot allocation model. Capacity is surely a key factor affecting displacement and implementation difficulties. This study contributes to propose a new mechanism for slightly weakening grandfather right, which can help decision makers to upgrade slot allocation policies.

The production of instant green tea requires hot-water extraction, which is time consuming and contributes to losses in aromatic compounds. In this study, an ultrasonic-assisted technology was used to improve the extraction efficiency of green tea, thereby shortening extraction time from 45 to 15 min. In pure water, the dissolution of caffeine and theanine did not change significantly, but total catechin dissolution increased by 0.23 mg/mL and total tea polyphenol dissolution decreased by 3.2 mg/mL. In 76.2% ethanol, the dissolution of caffeine and theanine did not change significantly, but total catechin dissolution increased by 1.57mg/mL and total tea polyphenol dissolution decreased by 1.5 mg/mL. Additionally, we used microwave-assisted technology to further improve the extraction efficiency of green tea, which shortened the extraction time to 2 min. However, the extraction rate remained unchanged. In pure water, the dissolution of caffeine and theanine did not change significantly, but the dissolution of total catechins increased by 0.41 mg/mL and the dissolution of tea polyphenols decreased by 2.9 mg/mL. Ultrasonic treatment increased the proportion of 3-hydroxybutan-2-one, (5S)-5-(hydroxymethyl)oxolan-2-one and 2-phenylethanol, which were the main aroma compounds in tea. Microwave treatment changed the aroma compounds in tea, causing losses in aroma compounds with low boiling point and maintaining (5S)-5-(hydroxymethyl)oxolan-2-one. The taste and aroma of instant green tea improved based on sensory evaluation results.

For personalized recommender systems,matrix factorization and its variants have become mainstream in collaborative filtering.However,the dot product in matrix factorization does not satisfy the triangle inequality and therefore fails to capture fine-grained information. Metric learning-based models have been shown to be better at capturing fine-grained information than matrix factorization. Nevertheless,most of these models only focus on rating data and social information, which are not sufficient for dealing with the challenges of data sparsity. In this paper,we propose a metric learning-based social recommendation model called SRMC.SRMC exploits users' co-occurrence pattern to discover their potentially similar or dissimilar users with symmetric relationships and change their relative positions to achieve better recommendations.Experiments on three public datasets show that our model is more effective than the compared models.

China combines green energy and industrial policy in its power market reform with various policy initiatives, including price support scheme for electricity from renewable sources and subsidies in the push for broader use of greener energy. This study focuses on the impacts of power market reform on the stock price volatility of listed power companies: 1) we use the Iterative Cumulative Sums of Squares (ICSS) algorithm to identify structural break points in stock prices; 2) we analyze the characteristics of stock price volatility based on the GARCH model; 3) we report the impact of power regulation on stock price fluctuations based on the Autoregressive Distributed Lag (ARDL) model. The result suggests three structural breaks in China’s power stock price volatility were related to the promulgation of power market reform policies. We find that industrial policies promote the reduction of power stock price fluctuations and its impact on power stock price volatility is consistent in the long run. However, our study also indicates the recent policies related to renewable energy do not have a very significant impact on the power stock market.

High-precision displacement sensing has been widely used across from both scientific researches and industrial applications. The recent interests in developing micro-opto-electro-mechanical systems (MOEMS) have given rise to an excellent platform for miniaturized displacement sensors. Advancement in this field during past years is now yielding integrated high-precision sensors which show great potential in applications ranging from photoacoustic spectroscopy to high-precision positioning and automation. In this review, we briefly summarize different techniques for high-precision displacement sensing based on MOEMS, and discuss the challenges for future improvement.

An active power dispatch method for a microgrid (MG) with multi-type loads, renewable energy sources (RESs) and distributed energy storage devices (DESDs) is the focus of this paper. The MG operates in a grid-connected model, and distributed power sources contribute to the service for load demands. The outputs of multiple DESDs are controlled to optimize the active power dispatch. Our goal with optimization is to reduce the economic cost under time-of-use (TOU) price, and to adjust the excessively high or low load rate of distributed transformers (DTs) caused by the peak-valley demand and load uncertainties. To simulate a practical environment, the stochastic characteristics of multi-type loads are formulated. The transition matrix of system state is provided. Then, a finite-horizon Markov decision process (FHMDP) model is established to describe the dispatch optimization problem. A learning-based technique is adopted to search the optimal joint control policy of multiple DESDs. Finally, simulation experiments are performed to validate the effectiveness of the proposed method, and the fuzzification analysis of the method is presented.