In this study, we test the performance of a compact gas chromatograph with photoionization detector (GC-PID) and optimize the configuration to detect ambient (sub-ppb) levels of benzene, toluene, ethylbenzene, and xylene isomers (BTEX). The GC-PID system was designed to serve as a relatively inexpensive (~$10k) and field-deployable air toxic screening tool alternative to conventional benchtop GCs. The instrument uses ambient air as a carrier gas, and consists of a Tenax-GR trap preconcentrator, a gas sample valve, two capillary columns, and a photoionization detector (PID) with a small footprint and low power requirement. The performance of the GC-PID has been evaluated in terms of system linearity and sensitivity in field conditions. The BTEX-GC system demonstrated the capacity to detect BTEX at levels as high as 500 ppb with a linear calibration range of 0-100 ppb. A detection limit lower than 1 ppb was found for all BTEX compounds with a sampling volume of 1 L. No significant drift in the instrument was observed. A time-varying calibration technique was established that requires minimal equipment for field operations and optimizes the sampling procedure for field measurements. With an analysis time of less than 15 minutes, the compact GC-PID is ideal for field deployment of background and polluted atmospheres for near-real time measurements of BTEX. The results highlight the application of the compact and portable GC-PID for community monitoring and screening of air toxics.

An ultra-low anti-reflection optical coating on both surfaces of a plastic cover slip was studied for use in confocal image measurement. The optical reflectance at a wavelength of 632.8 nm was less than 0.1% when the coated sample was placed in a liquid having a refractive index of 1.34 close to the aqueous solution of the biomaterial. The high- and low-index coating films, Substance-2 (PrTiO3) and silicon dioxide (SiO2), were measured by an ellipsometer to determine their optical refraction indices and extinction coefficients. Theoretically, when the two layer thicknesses are designed using the optical admittance diagram of the cover slip to approach the equivalent index of 1.34, a reflectance of 1.6×10-5% in the liquid could be obtained. Experimentally, the reflectance of the sample deposited on the two faces of the cover slip was 4.223±0.145% as measured in the air; and 0.050±0.002% as measured by a He-Ne laser in the liquid.

Federated learning trains a neural network model using the client's data to maintain the benefits of centralized model training, while maintaining the privacy. However, if the client data are not independently and identically distributed (non-IID) because of different environments, the accuracy of the model may suffer from client drift during training owing to discrepancies in each client's data. This study proposes a personalized federated learning algorithm based on the concept of multitask learning to divide each client model into two layers: a feature extraction layer and a category prediction layer. The feature extraction layer maps the input data to a low-dimensional feature vector space. Furthermore, the parameters of the neural network are aggregated with those of other clients using an adaptive method. The category prediction layer maps low-dimensional feature vectors to the label sample space, with its parameters remaining unaffected by other clients to maintain client uniqueness. The proposed personalized federated learning method produces faster learning model convergence rates and higher accuracy rates for the non-IID datasets in our experiments.

Background and Aims: The impact of antibody response after direct-acting antiviral (DAA) therapy in hepatitis C virus (HCV)-infected recipients before and after liver transplantation (LT) is still undetermined. Methods: In this observational cohort study, we aimed to explore the association of changes in anti-HCV antibody titers after pre-LT DAA therapy with allograft injury, including biliary complications (BCs) and acute cellular rejection (ACR). Results: A total of 153 cases were enrolled from January 2015 to February 2021. Serum anti-HCV antibody titers were assessed before and after (day 30) LT. Among all recipients, 31/153 (20.3%) had pre-LT DAA therapy (DAA group) and 122/153 (79.7%) did not undergo pre-LT DAA therapy (DAA-naïve group). Higher incidence of post-LT BCs was observed in the DAA group (P = 0.028). Compared with the DAA-naïve group, the DAA group had a significantly higher mean level of anti-HCV titer upregulation (P = 0.0024); furthermore, among the recipients with BCs (n = 28) and ACR (n = 41), those in the DAA group exhibited significantly higher mean levels of anti-HCV antibody titer upregulation (P < 0.005). Conclusion: In conclusion, we speculated that anti-HCV antibody titer upregulation, which might have been induced by restoration of HCV-specific immune responses with pre-LT DAA therapy, were associated with post-LT allograft injury.

Our results demonstrated that SWT stimulates osteoblastogenesis and increase the cell number of osteoblasts, suggesting positive regulatory effects on osteoblast differentiation. However, the effect of SWT on bone formation need further examination, since the expression of alp gene is downregulated. On the other hand, SWT appears to negatively regulate osteoclast differentiation and bone resorption, as number of osteoclasts and the expression of critical bone resorptive genes are all downregulated. Collectively, SWT might change the equilibrium of bone remodeling and increase the bone mass. Our data provided supportive evidences that this medicine formulation can be applied to treat osteoporosis or bone destructive diseases.

Background Diabetic patients have an increased risk of infections; however, the association between type 2 diabetes and hospital outcomes of sepsis remains controversial when the diabetes severity is not considered. We examined this association using nationwide and hospital-based databases concomitantly. Methods The first part of this study was conducted using 2 nationwide databases: the Longitudinal Cohort of Diabetes Patients and the Longitudinal Health Insurance Database 2000. The diabetic complication burden was evaluated using the adapted Diabetes Complications Severity Index score (aDCSI score). In the second part, we used the hospital-based database with laboratory data, such as initial blood glucose and HbA1c levels, to make comparisons between surviving and dead patients with type 2 diabetes and sepsis. Results The nationwide study included 19,719 type 2 diabetic sepsis patients and an equal number of non-diabetic patients. The diabetic sepsis patients had an increased odds ratio (OR) of 1.14 (95% CI 1.1-1.19) for hospital mortality. The OR for mortality increased as the complication burden increased (diabetic sepsis patients with aDCSI scores of 0, 1, 2, 3, 4, and ≥5 had ORs of 0.91, 0.87, 1.14, 1.25, 1.56, and 1.77 for mortality, respectively (all P<0.001 and P for trend <0.001)). A total of 1,054 diabetic sepsis patients were included from the hospital-based database. Initial blood glucose levels in the surviving and dead diabetic sepsis patients did not differ significantly: 273.9 ± 180.3 versus 266.1 ± 200.2 (mg/dL) (P=0.095). Moreover, the surviving diabetic sepsis patients did not have a lower HbA1c (%): 8.4 ± 2.6 versus 8.0 ± 2.5 (P=0.078). Conclusions In the case of type 2 diabetic sepsis patients, the diabetes-related complication burden is the major determinant of hospital mortality rather than the diabetes itself. Contrary to popular belief, initial blood glucose and HbA1c levels may not be as important as previously thought.

A digital text abstract presents the essential information of an article, and we can find the trend and value of the research by analyzing it rigorously and digging up knowledge. Therefore, this study focuses on the abstracts of index journals in China and Taiwan from July 2010 to June 2020 (a total of 3,283 abstracts). Through the concepts of text mining and natural language processing (NLP), it constructs processes such as text retrieval, text segmentation and word cloud analysis, TF-IDF weight analysis, co-word analysis, network analysis, and trend analysis, and analyses a large amount of text data. The results show that the scope of research in China covers the fields of social sports and sports science, and research in Taiwan covers both natural and social sciences. The network diagram highlights the richness of sports-related research fields in the two regions, but research on sports philosophy is relatively rare. It is suggested that all disci-plines/departments should re-allocate the same resources, so as to show a balanced development trend and help expand a new chapter in the sports academic field.

The paper addresses the challenging issue of trajectory tracking for uncertain quadrotor UAVs, particularly under the constraints of input saturation and external disturbances. It introduces adaptive laws for managing uncertainties in mass and inertia moments without requiring prior knowledge, ensuring effective control even with varying system parameters. To counteract the effects of input saturation, the study incorporates an auxiliary system designed to compensate for these limitations. Additionally, a disturbance observer(DO) is utilized to manage and mitigate the impact of time-varying external disturbances. The proposed control strategy integrates a sliding mode adaptive control approach with an inner-outer loop structure, enhancing robustness and adaptability. Numerical simulations demonstrate the effectiveness of the designed control strategy.

Background: miRNA-122 has been reported to be a useful tool for monitoring ACR after LT. IL-28B SNP rs8099917 genotype is known to contribute to the control of HCV infection. We sought to investigate the relationship between IL-28B SNP rs8099917 genotype and miRNA-122 expression and immune mechanism of ACR after LT using hepatitis C antibody calibration. Patients and Methods: A total of 45 patients with chronic hepatitis C received LDLT. IL-28B SNP rs8099917 genotyping was used to divide TT and GT groups. The relative expression levels of miRNA-122 were calculated by quantitative PCR as 2[(Ct of miR-122) (Ct of U6)] normalized to a reference gene and compared to a control sample, and the anti-HCV titers before and after LT were tracked to observe the relationship with ACR. Results: In the genotype of rs8099917, TT was significantly more associated with higher serum miRNA-122 levels than GT (p = 0.029). The ACR was significantly higher in genotype TT than in GT (p = 0.002). TT was significantly associated with low levels of pre-LT anti-HCV compared with GT (p = 0.022). Multivariate analysis with 95% confidence intervals showed a significant association between rs8099917 genotype TT, lower pre-LT and higher post-LT anti-HCV and ACR. Conclusion: Based on our current data, IL-28B SNP rs8099917 genotype TT may express higher miRNA-122 and correlate with lower Pre-LT and higher Post-LT anti-HCV titers, and may correlate to the pathogenesis of ACR after LT.

Guided ultrasonic waves are suitable for use in the context of structural health monitoring of thin-walled, plate-like structures. Hence, observing the wave propagation in the plates can provide an indication of whether damage has occurred in the structure. In this work, the wave propagation in fiber metal laminate consisting of thin steel foils and layers of carbon fiber-reinforced polymer is studied, focusing on the main propagation characteristics like dispersion diagrams and displacement fields. For this purpose, the dispersion diagrams derived from the analytical framework and numerical simulations are first determined and compared to each other. Next, the displacement fields are computed using the global matrix method for two excitation frequencies. The results derived from the analytical framework is used to validate numerically determined displacement fields based on a 2D and a 3D modeling approach. For both investigations the results of the analytical treatment and the numerical simulation show good agreement. Furthermore, the displacement field reveals the typical and well-known characteristics of the propagation of guided waves in thin-walled structures. Since the use of full 3D models involves a very high computational cost, this work also successfully investigates the possibility for model order reduction to decrease the computational time and costs of the simulation without the loss of accuracy.

Artificial intelligence has garnered significant attention in recent years as a rapidly advancing field of computer technology. With the continual advancement of computer hardware, deep learning has made breakthrough developments within the realm of artificial intelligence. Over the past few years, applying deep learning architecture in medicine and Industrial anomaly inspection has significantly contributed to solving numerous challenges related to efficiency and accuracy. Despite excellent results in radiological, pathological, endoscopic, ultrasonic, and biochemical examinations, this paper utilizes deep learning combined with image processing to identify spinal canal and vertebral foramen dimensions. In existing research, technologies such as corrosion and expansion in magnetic resonance image (MRI) processing have also strengthening the accuracy of results. Indicators such as area and Intersection over Union (IoU)are also provided for assessment. Among them, the mean average precision (mAP), for identifying intervertebral foramen (IVF) and intervertebral disc (IVD) through YOLOv4 is 95.6%. Resnet50 mixing U-Net was employed to identify the spinal canal and intervertebral foramen and achieved IoU scores of 79.11% and 80.89%.

Force reduction is one of the most important benefit of applying ultrasonic vibration on milling. However, most of studies so far are limited to experimental investigation. In the current study, an analytical predictive model on cutting forces in ultrasonic vibration-assisted milling is proposed. The three types of tool-workpiece criteria are considered based on the instantaneous position and velocity of tool center. Type I criterion indicates that there is no contact if the instantaneous velocity is opposite to tool rotation direction. Type II criterion checks whether the vibration displacement is larger than the instantaneous uncut chip thickness. Type III criterion considers the overlaps between current and previous tool paths due to vibration. If none of these criteria is satisfied, milling forces are nonzero. Then the calculation is performed by transforming milling and tool geometry configuration to orthogonal cutting at each instant. The orthogonal cutting forces are predicted through the exhaustive search of shear angle and calculation of shear flow stress on tool-chip interface. The axial force is then calculated based on tool geometry, and the milling forces in feed, cutting, and axial directions are calculated after coordinate transformation. The proposed predictive force model in ultrasonic vibration-assisted milling is validated through comparison to experimental measurements on Aluminum alloy 2A12. The predicted values are able to match the measured milling forces with high accuracy of average difference of 13.6% in feed direction and 13.8% in cutting direction.

In laser-assisted milling, higher temperature in shear zone softens the material potentially resulting in a shift of mean residual stress, which significantly affects the damage tolerance and fatigue performance of product. In order to guide the selection of laser and cutting parameters based on the preferred mean residual stress, inverse analysis is conducted by predicting residual stress based on guessed process parameters, which is defined as the forward problem, and applying iterative gradient search to find process parameters for next iteration, which is defined as the inverse problem. An analytical inverse analysis is therefore proposed for the mean residual stress in laser-assisted milling. The forward problem is solved by analytical prediction of mean residual stress after laser-assisted milling. The residual stress profile is predicted through the calculation of thermal stress, by treating laser beam as heat source, and plastic stress by first assuming pure elastic stress in loading process, then obtaining true stress with kinematic hardening followed by the stress relaxation. The variance-based recursive method is applied to solve inverse problem by updating process parameters to match the measured mean residual stress. Three cutting parameters including depth of cut, feed per tooth, and cutting speed, and two laser parameters including laser-tool distance and laser power, are updated with respected to the minimization of resulting residual stress and measurement in each iteration. Experimental measurements are referred on the laser-assisted milling of Ti-6Al-4V grade 5 and ELI. The percentage difference between experiments and predictions is less than 5% for both materials, and the selection is completed within 50 loops.

The pharmacological effects of the fruiting body of Ophiocordyceps sinensis (Os) exerted antioxidant, anti-virus, and immunomodulatory, whereas the anti-inflammatory effects and active components of Os mycelial submerged culture (OMSC) are not known. This study aimed to investigate the active compounds in the fermented liquid (FLOS), hot water (WEOS), and 50-95% (EEOS-50, EEOS-95) ethanol extracts of OMSC and their anti-inflammatory effects and potential mechanisms in LPS-stimulated microglial BV2 cells. The results demonstrated that all of the OMSC extracts could inhibit NO production in BV2 cells. EEOS-95 exhibited the strongest inhibitory effects (41 % inhibitory ability at 500 µg/mL), and its ergosterol, GABA, total phenolic, and total flavonoid contents were significantly higher than those of the other extracts (18.60, 18.60, 2.28, and 2.14 mg/g, p &lt; 0.05, respectively). EEOS-95 also has a strong inhibitory ability against IL-6, IL-1β and TNF-α with IC50 of 617, 277 and 507 µg/mL, respectively, which is higher than that of 1 mM melatonin. The anti-inflammatory mechanism of EEOS-95 seems to be associated with up-regulation of PPAR-γ/Nrf-2/HO-1 antioxidant-related expression and down-regulation of NF-κB/COX-2/iNOS pro-inflammatory expression signaling. Therefore, we hypothesized that EEOS-95 can prevent neurodegenerative diseases, but the effect on the application in vivo should be further investigated.

Excretory-secretory products (ESPs) are the main research targets for investigating the hosts and helminths interaction. Parasitic worms can migrate to parasitic sites and avoid the host immune response by secreting this product. Angiostrongylus cantonensisis an important food-borne zoonotic parasite that causes severe neuropathological damage and symptoms, including eosinophilic meningitis or meningoencephalitis in humans. Benzaldehydes are organic compounds composed of a benzene ring and formyl substituents. This compound has anti-inflammatory and antioxidation properties. Previous studies showed that 3-hydroxybenzaldehyde (3-HBA) and 4-hydroxybenzaldehyde (4-HBA) can reduce apoptosis in A. cantonensis ESPs treated astrocytes. These results on the protective effect underlying benzaldehyde have primarily focused on cell survival. The study was designed to investigate the molecular mechanisms of endoplasmic reticulum stress (ER stress) and oxidative stress in astrocytes in A. cantonensis ESPs treated astrocytes and to evaluate the therapeutic consequent of 3-HBA and 4-HBA. First, we initially established the RNA-seq dataset in each group, including Normal, ESPs, ESPs+3-HBA, and ESPs+4-HBA. We also found that benzaldehyde (3-HBA and 4-HBA) can stimulate astrocytes to express ER stress-related molecules after ESP treatment. The level of oxidative stress could also be decreased in astrocytes by elevating antioxidant activity and reducing ROS generation. These results suggested that benzaldehyde may be a potential therapeutic compound for human angiostrongyliasis to support brain cell survival by inducing the expression levels of ER stress- and oxidative stress-related pathway.

Lamb waves occur in thin-walled structures in two wave modes, the symmetric and antisymmetric mode. Their oscillation on the structures‘ surfaces is either in phase (symmetric) or shifted by a phase angle of π (antisymmetric). In this work, a method is developed to compare the surfaces‘ oscillation phase relation. It is based on the evaluation of time signals regarding the instantaneous phase angle using the continuous wavelet transformation and as a comparative method the short-time Fourier transformation. For this purpose, numerical simulations utilizing the finite element method provide time signals from the top and bottom surface of different thin-walled structures. They differ with respect to their material settings and laminate configurations. The numerically obtained time signals are evaluated by the developed methods. The occurring oscillation phase differences on the top and bottom surface are studied and both methods are compared. Subsequently, the oscillation phase is evaluated experimentally for the wave propagation in a fiber metal laminate. It is shown that the method based on the continuous wavelet transformation is suitable for the evaluation of oscillation phase relations in time signals. Additionally, it is proven that fiber metal laminates show only two phase relations which indicates the occurrence of Lamb waves.

Currently, efficient utilization of low-grade thermal energy is a great challenge. Thermoelectricity is an extremely promising method of generating electrical energy from temperature differences. As a promising energy conversion technology, thermo-electrochemical cells (TECs) have attracted much attention in recent years for their ability to convert thermal energy directly into electricity with high thermal power. Within TECs, anions and cations gain and lose electrons, respectively at the electrodes using the potential difference between the hot and cold terminals of the electrodes by redox couples. Additionally, the anions and cations therein are constantly circulating and mobile via concentration diffusion and thermal diffusion, providing an uninterrupted supply of power to the exterior. This review article focuses mainly on the operation of TECs, recent ad-vances in redox couples, electrolytes, and electrodes. The outlook for optimization strategies re-garding TECs is also presented in this paper.

Iron overnutrition has been implicated with higher risk of developing metabolic and cardiovascular diseases, including metabolic syndrome (MetS), while iron deficiency anemia exacerbates many underlying chronic conditions. Hemoglobin (Hb) concentration in the blood, which reflects a major functional iron (i.e., heme iron) in the body, may serve as a surrogate of iron nutrition status. We conducted sex-specific observational association studies where we carefully titrated the association between Hb deciles and MetS and its components among the Taiwanese Han Chinese (HC) from the Taiwan Biobank and Europeans of White ancestry from the UK Biobank, representing two large ethnicities. Our data show that at higher-than-normal levels of Hb, increasing deciles of Hb concentration were significantly associated with MetS across all sex subgroups in both ethnicities, with the highest deciles resulting in up to three times greater risks than the reference group [Taiwanese HC: OR=3.17 (95% CI, 2.75-3.67) for Hb >16.5 g/dL in men, OR=3.11 (2.78-3.47) for Hb >14.5 g/dL in women; European Whites: OR=1.89 (1.80-1.98) for Hb >16.24 g/dL in men, OR=2.35 (2.24-2.47) for Hb >14.68 g/dL in women]. The association between stronger risks and increasing Hb deciles was similarly observed with all metabolic components except diabetes. Here we found that both the highest Hb decile groups and contrarily the lowest ones, with respect to the reference, were associated with higher odds of diabetes in both ethnic groups [e.g., Taiwanese HC men: OR=1.64 (1.33-2.02) for Hb >16.5 g/dL, OR=1.71 (1.39-2.10) for Hb <13.5 g/dL; European Whites women: OR=1.39 (1.26-1.45) for Hb >14.68 g/dL, OR=1.81 (1.63-2.01) for Hb <12.39 g/dL]. These findings confirm that elevated Hb concentrations, a potential indicator of iron overnutrition, may play a role in the pathophysiology of MetS and metabolic components.

This paper focuses on parametric model order reduction (PMOR) of guided ultrasonic wave propagation and its interaction with damage in a fiber metal laminate (FML). Structural health monitoring in FML seeks to detect, localize and characterize the damage with high accuracy and minimal use of sensors. This can be achieved by the inverse problem analysis approach which employs the signal measurement data recorded by the embedded sensors in the structure. The inverse analysis requires to solve the forward simulation of the underlying system several thousand times. These simulations are often exorbitantly expensive and triggered the need for improving their computational efficiency. A PMOR approach hinged on the proper orthogonal decomposition method is presented in this paper. An adaptive parameter sampling technique is established with the aid of a surrogate model to efficiently update the reduced-order basis in a greedy fashion. A numerical experiment is conducted to illustrate the parametric training of the reduced-order model. The results show that the reduced-order solution based on the PMOR approach is accurately complying with that of the high fidelity solution.

This study constructs an evaluation system of high-quality utilization of urban land (HUUL) and comprehensively adopts the entropy method, the kernel density estimation, and the geodetector model to analyze the spatio-temporal evolution and driving factors of the HUUL levels of 284 Chinese cities from 2006 to 2020. The measurement results show that during 2006-2020, the HUUL level showed an obvious upward trend, and the eastern region > the central region > the overall region > the western region > the northeastern region. According to the kernel density map, except for the region of the west, there is a trend of different degrees of enlargement of the difference in the main peak position of the HUUL level among cities in the other three regions, and there are individual cities in the eastern and western regions with much higher HUUL levels than the others; According to the results of factor detection, it can be seen that innovative utilization and open utilization are the endogenous dominant factors that promote the improvement of HUUL level, and the level of economic development is the exogenous dominant factor that supports the im-provement of high-quality utilization of urban land.

Based on the minimum conduction band edge caused by the minimum channel potential resulting from the quasi-3D scaling theory and the 3D density of state (DOS) accompanied by the Fermi-Dirac distribution function on the source and drain sides, a unified semiconductor-device-physics-based ballistic model is developed for the threshold voltage of modern multiple-gate (MG) transistors, including FinFET, W-gate MOSFET, and Nanosheet (NS) MOSFET. It is shown that the thin silicon, thin gate oxide, and high work function will alleviate the ballistic effects and resist the threshold voltage degradation. Besides, as the device dimension is further reduced to give rise to the 2D/1D DOS, the lowest conduction band edge is hence increased to resist the threshold voltage degradation. The nanosheet MOSFET exhibits the largest threshold voltage among the three transistors due to the smallest minimum conduction band edge caused by the quasi-3D minimum channel potential. Compared to P-type MOSFET (P-FET), the N-FET shows more threshold voltage because the electron has a more effective mass than the hole

There is a potential for synergy effects in utilizing CO2 for both enhanced gas recovery (EGR) and geothermal energy extraction (CO2-plume geothermal, CPG) from natural gas reservoirs. This “combined CO2-EGR–CPG system” has been introduced as a feasible approach that constitutes a CO2 Capture double-Utilization and Storage (CCUUS) system. In this study, we carry out reservoir simulations, using TOUGH2, to evaluate the sensitivity of the natural gas recovery, pressure buildup, and geothermal power generation performance of the combined system to various key reservoir and operational parameters. The reservoir parameters include horizontal permeability, permeability anisotropy, reservoir temperature, and pore-size-distribution index; while the operational parameters include wellbore diameter and ambient surface temperature. Using an example of a natural gas reservoir model, we also investigate the effects of different strategies of transitioning from the CO2-EGR stage to the CPG stage on the energy-recovery performance metrics and on the two-phase fluid-flow regime in the production well. The simulation results show that overlapping the CO2-EGR and CPG stages and having a relatively brief period of CO2 injection but no production (which we call the CO2-plume establishment stage) achieves the best overall energy (natural gas and geothermal) recovery performance. Permeability anisotropy and reservoir temperature are the parameters the natural gas recovery performance of the combined system is most sensitive to. The geothermal power generation performance is most sensitive to the reservoir temperature and the production wellbore diameter. The results of this study pave the way for future CPG-based geothermal power-generation optimization studies. For a CO2-EGR–CPG project, the results can be a guide regarding the required accuracy of the reservoir parameters during exploration and data acquisition.

It is important to reduce the computation complexity while maintaining the accuracy of convolution neural networks. We deem it is possible to further reduce the network complexity while ensuring the accuracy. In this paper, we propose a novel feature extraction network called DSRNet which is lightweight but effective. DSRNet follows the basic ideas of stacking modules and short connection, introduces Depthwise Separable convolution and utilizes the Dilated convolution. The proposed network has fewer parameters and achieves outstanding speed. We conducted comprehensive experiments on CIFAR10, CIFAR100 and STL10 datasets, and the results showed the DSRNet has great performance improvement in terms of accuracy and speed.

The goal of this paper is to fabricate innovative diaphragm headphones using graphene oxide paper (GOP) and GOP/epoxy nanocomposites (GOPC). Initially, graphene oxide suspension is fabricated, and the vacuum filtration method is adopted to make GOP. Then vacuum bag molding is used to fabricate GOPC from GOP. Hot pressing and associated molds are adopted to fabricate line-indented (GOPC-L) or curve-indented patterns (GOPC-C) on the GOPC. The performance of one kind of GOP and three kinds of GOPC diaphragm headphones is analyzed based on their sound pressure level (SPL) curves achieved by the Soundcheck measurement system. There are four important processing parameters that will influence the performance of the diaphragm, including material type GOP versus GOPC, indented pattern type, sonication time on suspension, and graphene weight fraction in suspension. Compliances of various diaphragms are measured by the Klippel LPM laser measurement system. The results indicate that effects of sonication time and graphene weight fraction on SPL of GOP and GOPC headphones are in reverse, and this is associated with their difference on compliance (modulus), mass, damping ratio, and microstructure uniformity. Either GOPC-L or GOPC-C seems to improve the microstructure of the GOPC, and leads to better SPL performance. The correlation between the previous four factors and SPLs of four kinds of diaphragm headphones is proposed by using scanning electron microscope (SEM) to examine the microstructure of these diaphragms.

In the clock network design, the trade-off between power consumption and timing closure is an important and difficult issue. To achieve this target, a hybrid clock network architecture that combines both clock tree and clock mesh seems to be a promising solution. In this paper, we propose a novel clock mesh architecture – cross-mesh, with the average dispersion of the overall driving force, our methodology creates small non-zero skew clock trees. In addition, we integrate clock gating and register clustering techniques to further reduce dynamic power consumption. The proposed algorithms have four stages: cross-mesh planning, register clustering, mesh line connecting, and load balancing. Experimental results show that our methodology and algorithms get feasible solution effectively and improve both power consumption and clock skew simultaneously.

This study centers on childcare facilities catering to children with moderate cerebral palsy, exploring a four-phase process: (1) cultivating an understanding and acceptance, (2) integrating specialized resources, (3) developing strategic plans, and (4) establishing stable collaboration. The case study demonstrates the profound impact of well-rounded support systems. Children with cerebral palsy showed marked improvements in development and emotional stability. Concurrently, their peers developed greater empathy and cooperative skills, smoothly adjusting to the inclusive setting. Additionally, the childcare staff refined their methods and attitudes, enhancing their ability to meet each child's specific needs and thus elevating the standard of integrated care.Concluding with three strategic recommendations, the paper proposes measures to augment the quality of care for children with special needs. These include defining clearer guidelines and policies for special needs care in childcare environments, emphasizing professional development and the amalgamation of diverse resources to cultivate a more skilled caregiving workforce, and encouraging robust partnerships between parents and childcare facilities. These recommendations are expected to significantly influence the domain of inclusive education, providing crucial insights for those engaged in early childhood care and education..

For the numerical simulation of components made of short fiber-reinforced composites the correct prediction of the deformation including the elastic and plastic behavior and its spatial distribution is essential. When using purely deterministic modeling approaches the information of the probabilistic microstructure is not included in the simulation process. One possible approach for the integration of stochastic information is the use of random fields. In this study numerical simulations of tensile test specimens are conducted utilizing a finite deformation elastic-ideal plastic material model. A selection of the material parameters covering the elastic and plastic domain are represented by cross-correlated second-order Gaussian random fields to incorporate the probabilistic nature of the material parameters. To validate the modeling approach tensile tests until failure are carried out experimentally, that confirm the assumption of spatially distributed material behavior in both the elastic and plastic domain. Since the correlation lengths of the random fields cannot be determined by pure analytic treatments, additionally numerical simulations are performed for different values of the correlation length. The numerical simulations endorse the influence of the correlation length on the overall behavior. For a correlation length of 5mm a good conformity with the experimental results is obtained. Therefore, it is concluded, that the presented modeling approach is suitable to predict the elastic and plastic deformation of a set of tensile test specimens made of short fiber-reinforced composite sufficiently.

Holistic information integrity for managing wicked problems, developing equity is getting attention. Artifitial intelligence based topologies, dual sensor-information nodes, are prototyped to offer more availability, reliability, maintainability for operating healthy urbanism. Bipartite spider-webs, cube-connected cycles are aimed in ‘the radial-ring urban-building skeleton’ and ‘wetlands and sparsely populated areas’, respectively. Furthermore, honeycomb tori, mathematical HT(m), m≥2, for tasks related to wireless communications, are found having two mutually independent Hamiltonian paths (MIHP). This parallelism creates dual cipher-coding, supports logistic privacy, and help prevent information loss, electromagnetic interference, unexpected changes caused by such as clogged water.

Based on the data of A-share listed companies in Shanghai and Shenzhen of China from 2011 to 2018 and the digital inclusive finance index of Peking University (2011-2018), this paper empirically tests the impact of digital finance development on corporate social responsibility in various provinces of China and its impact mechanism. The results show that: (1) the development of digital finance helps to promote the fulfillment of corporate social responsibility; (2) the influence mechanism of the development of digital finance to promote the fulfillment of corporate social responsibility lies in that it reduces the cost of debt financing and leads to the improvement of corporate social responsibility.(3) Further research shows that the positive relationship between digital finance and corporate social responsibility is more significant in private enterprises. At the same time, the impact is more significant in areas with poor market environment. The above research shows that the development of digital finance has a significant positive effect, which will improve the level of corporate social responsibility.

This is a survey study that dialysis patients were randomly sampled from a medical center in northern Taiwan, and those who gave their consent to participate were included in this study. The purpose of this study was to explore the correlation between depression, hope, and quality of life of dialysis patients. All subjects agreed to take "Beck’s Depression Inventory", " The Chinese version of Herth Hope Index" and " The Chinese version of Kidney Disease Quality of Life" (KDQOL-SFTM). Data were processed using SPSS for descriptive and inferential statistics. The results showed that patients were 12.45±SD 9.03, which was mild depression, the mean score of hope was 34.25, which was equivalent to 72.60%, and was at the middle level. In KDQOL-SFTM, the score in mental composite (M=42.65, SD=8.81) was higher than in physical composite (M=37.38, SD=9.28), and the score was at the intermediate quality of life, and hope and depression were significantly and negatively correlated. This study suggests that dialysis case managers provide nursing guidance to help dialysis patients learn comfortable care methods and support the resilience they need.

We aimed to evaluate the protective effects of acetyl-xylogalactan on the activity of RAW264.7 macrophages against heat stress. To this end, we assessed cell survival, phagocytic activity, in-tracellular Ca2+ level, mitochondria potential exchange, apoptotic assay findings, galactosidase activity and the RNA-seq by NGS and real-time polymerase chain reaction (PCR) expression. In our evaluation of macrophage morphology at 37°C and 41°C, the macrophages showed an oval shape at 41°C , unlike the spindle shape at 37°C. Therefore, 41°C was chosen as the heat stress condition. Subsequently, we designed an experiment to evaluate changes in the RAW264.7 macrophages after acetyl-xylogalactan treatment under heat stress. The survival of RAW264.7 macrophages treated with acetyl-xylogalactan was higher than that of controls that were not treated with acetyl-xylogalactan. Moreover, on the basis of the results of the annexin-V detection assay, the apoptotic activity of macrophages appeared to have reduced after treatment with ac-etyl-xylogalactan. Moreover, treatment with acetyl-xylogalactan resulted in a stronger recovery trend in the intracellular Ca2+ and mitochondrial membrane potential after heat stress. RNA sequencing and real-time polymerase chain reaction (PCR) illustrated that Sarcodia suieae acetyl-xylogalactan could upregulate the expression of the anti-apoptosis Cflar gene and down-regulate the expression of the apoptosis factors Ddit3, and Hyou1 to protect macrophages under heat stress.

Embracing innovative digital technologies within educational systems is essential for overcoming challenges in modern learning environments, especially in the post-COVID-19 era. Teaching sustainability management in higher education institutions with innovative digital tools plays a fundamental role in the transition toward sustainable societies. Suitable game design elements play a significant role in facilitating sustainable learning. This study explored the effectiveness of incorporating business simulation games with project-based learning (PBL) in a flipped classroom setting. This approach was adopted within the context of a university cross-border e-commerce course to prepare students for acquiring 21st -century skills as higher-order thinking skills in a rapidly changing educational landscape. A quasi-experimental method was employed, involving a total of 60 university students from China's Zhejiang Province. Participants completed an online questionnaire designed to assess their learning engagement across three dimensions (cognitive, emotional, and behavioral) as well as their higher-order thinking skills (problem-solving, critical thinking, and creativity). The results show that the business simulation games combined with flipped classroom learning had a significantly positive impact on students’ learning outcomes, enhancing their problem-solving, critical thinking, and creative capabilities. Importantly, this approach also improved student engagement and promoted sustainable practices by applying real-life scenarios in an interactive environment. We conclude that business simulation games integrated with project-based learning (PBL) in flipped classroom settings represent a valuable educational approach. This approach not only enhances learning engagement but also fosters the development of higher-order thinking skills, encouraging students to adopt sustainable learning practices.

In all areas of medicine, especially in radiology, computers are increasing year by year. Filmless radiology, speech recognition software, electronic application forms, and teleradiology are recent developments that have greatly improved radiologists' performance. This research explores radiology software trends, predictions, and the challenges posed by informatics and historical trend analysis. The rationale behind this research is that information technology (IT) is overgrowing almost every day. We must continuously seek new ways to apply IT to make more use of resources. Consequently, IT becomes increasingly crucial to radiology organizations' innovative thinking, workflow, and business models. This study aimed to analyze all radiology software publications in the Science Citation Index (SCI). From 1991 to July 2021, SCI was used to search for publications systematically. We have also widely used this historical method in radiology software research. The findings and discussions are base on an assessment of trends, predictions, contributions, and challenges in radiology software, and we are exploring radiology software with six evolutionary stages. The gift of this research is that radiology managers realize that the use of new information technologies is closely related to survival in a competitive environment. Radiology companies can review these new technologies to develop more innovative business models and services to improve operational deficiencies.

Carbapenemase-producing organisms (CPOs) present a major threat to public health, demanding precise diagnostic techniques their detection. Discrepancies among CPO tests have raised concerns, partly due to limitations in detecting bacterial diversity within host/specimen. We explored the impact of unbiased colony selection on carbapenemase testing and assessed its relevance on various tests. Based on "FirstAll" for unbiased colony selection to reduce bias, we compared modified carbapenem inactivation method/EDTA-modified carbapenem inactivation method (mCIM/eCIM), Carba5, the CPO panel, and multiplex PCR (M-PCR). Initially, we compared FirstAll to conventional colony selection for mCIM. Second, we used M-PCR as a reference, to evaluate test performance across seven CPO species. The results revealed that FirstAll selection improved carbapenemase detection, revising false-negative in 10.5% of K. pneumoniae isolates. In addition, 12.4% of CPOs tested positive for multiple carbapenemase genes. Both the Carba5 test and CPO panel showed suboptimal performance (sensitivity/specificity: Carba5 75.5%/89.0%, CPO panel 78.1%/74.0%). Carba5 test provided specific carbapenemase class assignments but CPO panel failed in 20.3% of cases. Carba5 test and the CPO panel results correlated well with ceftazidime-avibactam minimal inhibitory concentrations (MICs). Concordance for class A/D with MICs was 88.3% for Carba5 and 92.0% for the CPO panel; whereas for class B, it was 86.5% for Carba5 and 76.2% for the CPO panel. In conclusion, FirstAll as the unbiased colony selection impacted carbapenemase testing. With FirstAll, the diagnostic performance of either Carba5 or the CPO panel was compromised. The utilization of ceftazidime-avibactam guided by either the CPO panel or Carba5 was appropriate.

This work investigates how integrated polyimide inlays with applied sensor bodies influence the guided ultrasonic wave propagation in narrow glass fiber-reinforced polymer specimens. Preliminary numerical simulations indicate that in a damping-free specimen, the inlays show reflections for the S0-mode propagation. Hence, an air-coupled ultrasonic technique and a 3D laser Doppler vibrometer measurement are used to measure different parts of the propagating waves’ displacement field after burst excitation at different frequencies. No significant reflections on the inlay can be seen in the experiments. However, it is shown that the reflections from the strip specimen’s narrow width cause periodical reflections that superimpose with the excited wave fronts. A continuous wavelet transformation in the time-frequency domain filters discontinuities from the measurement signal and is used for reconstruction of the time signals. The reconstructed signals are used in a spatial continuous wavelet transformation to identify the occurring wavelengths and hence to prove the assumption of reflections from the narrow edges. Since the amplitude of the reflections identified in the numerical data at the polyimide inlays are an order of magnitude smaller than the excited wave packages, it is concluded that material damping of the epoxy resin matrix extincts possible reflections from the inlays.

The working environment of mining electric locomotives is wet and muddy coal mine 1 roadway. There may be idling or slipping between the wheels and rails of mining electric locomotives 2 due to low friction between the wheel and rail and insufficient utilization of creep rate. Therefore, it 3 is necessary to control the creep rate within a reasonable range. In this paper, the autonomous control 4 algorithm for mining electric locomotives based on improved ε-greedy is theoretically proven to be 5 convergent and effective firstly. Secondly, after analyzing the contact state between the wheel and rail 6 under wet and slippery road conditions, it was concluded that the value of creep rate is an important 7 factor affecting the autonomous driving of mining electric locomotives. Therefore, the autonomous 8 control method for mining electric locomotives based on creep control is proposed in this paper. 9 Finally, the effectiveness of the proposed method was verified through simulation. The problem of 10 wheel slipping and idling caused by insufficient friction of mining electric locomotives in coal mining 11 environments is effectively suppressed. Autonomous operation of vehicles with optimal driving 12 efficiency can be achieved through quantitative control and utilization of the creep rate between 13 wheels and rails

Static standing postural stability has been measured by multiscale entropy (MSE), which is used to measure complexity. In this study, we used the average entropy (AE) to measure the static standing postural stability, as AE is a good measure of disorder. The center of pressure (COP) trajectories were collected from 11 subjects under four kinds of balance situation, from stable to unstable: bipedal with open eyes, bipedal with closed eyes, unipedal with open eyes, and unipedal with closed eyes. The AE, entropy of entropy (EoE), and MSE methods were used to analyze these COP data, and EoE was found to be a good measure of complexity. The AE of the 11 subjects sequentially increased by 100%as the balance situations progressed from stable to unstable, but the results of EoE and MSE did not follow this trend. Therefore, AE, rather than EoE or MSE, is a good measure of static standing postural stability. Furthermore, the comparison of EoE and AE plots exhibited an inverted U curve, which is another example of a complexity versus disorder inverted U curve.

The shear stress generated by wall turbulence is the main cause of wall friction resistance in turbulent flow through pipes. This paper investigates the impact of inserting rest periods (regions of constant Reynolds number) within the pulsating operating cycle of velocity on the fully turbulent flow at large time-averaged Reynolds numbers, using the Large Eddy Simulation (LES) method. The study aims to explore the effect of increasing rest periods within pulsations on drag resistance. The dimensionless shear stress and drag reduction rates during different time periods of rest were analyzed. Numerical simulation results indicate that the pulsating velocity operation mode does not necessarily lead to drag reduction; it may even result in increased resistance. Inserting rest periods within the pulsation cycle can achieve drag reduction effects, with the maximum drag reduction rate reaching 21.8\%. Comparisons with experimental data and Direct Numerical Simulation (DNS) from the literature validate the feasibility of using the LES method for pipe pulsating operation modes.

Soy protein isolate (SPI) based materials are abundant, biocompatible, renewable, and biodegradable. In order to improve the tensile strength (TS) of SPI films, we prepared a novel composite film modified with microcrystalline cellulose (MCC) and metal nanoclusters (NCs) in this research. The effects of the modification of MCC on the properties of SPI-Cu NCs and Zn NCs films were investigated. Attenuated total reflectance-Fourier transformed infrared spectroscopy analyses and X-ray diffraction patterns characterized the strong interactions and reduction of the crystalline structure of the composite films. Scanning electron microscope showed the enhanced cross-linked and entangled structure of modified films. Compared with untreated SPI film, the tensile strength of the SPI-MCC-Cu and SPI-MCC-Zn films increased from 2.91 MPa to 13.95 and 6.52 MPa, respectively. Moreover, the results also indicated their favorable water resistance with higher water contact angle. Meanwhile, the composite films exhibited increased initial degradation temperatures, demonstrating their higher thermostability. The results suggested that MCC could effectively improve the performance of SPI-NCs films, which would provide a novel preparation method for environmentally friendly SPI-based films in the applications of packaging materials.

Background: Improving patients’ quality of life (QoL) is a principal objective of all treatment in any clinical setting, including oncology practice. Cancer-associated inflammation is implicated in disease progression and worsening of patients’ QoL. Conventional anticancer therapeutics while selectively eliminating cancerous cells, are evaded by stem cell-like cells, and associated with varying degrees of adverse effects, thus reducing patients’ QoL. This necessitates novel therapeutic approaches with enhanced efficacy, minimal or no treatment-related adverse effects, and improved QoL in patients with cancer, especially those with metastatic/advance stage disease. Methods: Sequel to our team’s previous publication, the present study explores probable effects of Astragalus polysaccharides (PG2) on cancer-related inflammatory landscape and known determinants of QoL, as well as the probable link between the two to provide mechanistic insight. In exploratory double blind randomized controlled trial using patients with metastatic disease (n=23), we comparatively evaluated the therapeutic efficacy of high (500mg) or low (250mg) dose PG2 administered intravenously (i.v.), with particular focus on its suggested anti-inflammatory function and the probable effect of same on QoL indices at baseline, then at weeks 4 and 8 post-PG2 treatment. Results: All 23 patients with metastatic disease treated with either low or high PG2 experienced reduced pain, nausea, vomiting and fatigue, as well as better appetite and sleep, culminating in improved global QoL. This was most apparent in the high dose group, with significant co-suppression of pro-inflammatory interleukin (IL)-1β, IL-4, IL-6, IL-13, IL-17, monocytes chemotactic protein (MCP)1, granulocyte-macrophage colony-stimulating factor (GM-CSF), vascular endothelial growth factor (VEGF), tumor growth factor (TGF)-β1, interferon (IFN)-γ, and immune suppressors IL-10, and IL-12. Univariate and multivariate analyses revealed that IL-1β, IL-13 and GM-CSF are independent prognosticators of improved QoL. Conclusion: This proof-of-concept study provides premier evidence of functional association between PG2 anti-inflammatory effects and improved QoL in patients with advanced stage cancers, laying the groundwork for future larger cohort blinded controlled trials to establish the efficacy of PG2 as adjuvant anticancer therapy in metastatic or advanced stage clinical settings.

Wind energy is a kind of renewable energy with great potential for development. This study mainly investigated the application of shock waves generated by high-pressure gases (wind energy) for generating energy. In this study, we designed a new supersonic shock wave generator that can be reused without disassembling and assembling bolts and developed a supersonic shock wave monitoring system. This system monitored the velocity of the generated shock waves, which was Mach 3-5, and the output pressure was more than 100 times higher than the input pressure of the shock wave generator tank.Then, we developed a power generation system driven by supersonic shock waves based on the characteristics of the new shock wave generator, which can generate high-pressure and high-speed blast waves and can be reused. The shock wave generator can repeatedly generate high-pressure waves to drive the Tesla turbine and then the magnetic energy generator for power generation. We established a complete control process for power generation driven by shock waves by controlling the valve stem. The system can detect the tank pressure, output pressure, gas flow, rotation speed, voltage, and current during the control process for the performance analysis of power generation.

Characterization of cancer cells and neural stem cells indicates that tumorigenicity and pluripotency are coupled cell properties determined by neural stemness, and tumorigenesis represents a process of progressive loss of original cell identity and gain of neural stemness. This reminds of a most fundamental process required for the development of the nervous system and body axis during embryogenesis, i.e., embryonic neural induction. Neural induction is that, in response to extracellular signals that are secreted by the Spemann-Mangold organizer in amphibians or the node in mammals and inhibit epidermal fate in ectoderm, the ectodermal cells lose their epidermal fate and assume the neural default fate and consequently, turn into neuroectodermal cells. They further differentiate into the nervous system and also some non-neural cells via interaction with adjacent tissues. Failure in neural induction leads to failure of embryogenesis, and ectopic neural induction due to ectopic organizer or node activity or activation of embryonic neural genes causes a formation of secondary body axis or a conjoined twin. During tumorigenesis, cells progressively lose their original cell identity and gain of neural stemness, and consequently, gain of tumorigenicity and pluripotency, due to various intra-/extracellular insults in cells of a postnatal animal. Tumorigenic cells can be induced to differentiation into normal cells and integrate into normal embryonic development within an embryo. However, they form tumors and cannot integrate into animal tissues/organs in a postnatal animal because of lack of embryonic inducing signals. Combination of studies of developmental and cancer biology indicates that neural induction drives embryogenesis in gastrulating embryos but a similar process drives tumorigenesis in a postnatal animal. Tumorigenicity is the manifestation of aberrant occurrence of pluripotent state in a postnatal animal. Pluripotency and tumorigenicity are both but different manifestations of neural stemness in pre- and postnatal stage, respectively, of animal life. The unique property of neural stemness is derived from the evolutionary advantage of neural genes and the neural-biased state of the last common unicellular ancestors of metazoan. Based on these findings, I discuss about some confusion in cancer research, propose to distinguish the causality and associations and discriminate causal and supporting factors involved in tumorigenesis, and suggest revisiting the focus of cancer research.

Thalassemia is a heterogeneous congenital hemoglobinopathy common in the Mediterranean region, Middle East, Indian subcontinent, and Southeast Asia with increasing incidence in Northern Europe and North America due to immigration. Iron overloading is one of the major long-term complications in patients with thalassemia and can lead to organ damage and carcin-ogenesis. Hepatocellular carcinoma (HCC) is one of the most common malignancies in both transfusion-dependent thalassemia (TDT) and non-transfusion-dependent thalassemia (NTDT). The incidence of HCC in patients with thalassemia has increased over time, as better chelation therapy confers a sufficiently long lifespan for the development of HCC. The mechanisms of iron overloading-associated HCC development include the increased　reactive oxygen species (ROS), inflammation cytokines, dysregulated hepcidin, and ferroportin metabolism. The treat-ment of HCC in patients with thalassemia was basically similar to those in general population. However, due to the younger age of HCC onset in thalassemia, regular surveillance for HCC development is mandatory in TDT and NTDT. Other supplemental therapy and experience of novel treatment for HCC in thalassemia population were also reviewed in this article.

Background: The circadian system, a vital temporal regulator influencing physiological processes, has implications for cancer development and treatment response. Our study assesses circadian timing's impact on whole-brain radiotherapy outcomes in brain metastases for personalized cancer therapy insights. Aim: Evaluate circadian influence on radiation treatment timing and its correlation with clinical outcomes. Identify patient populations benefiting from interventions synchronizing circadian rhythms, considering subgroup differences and potential disparities related to social determinants of health (SDoH). Design: IRB-approved retrospective analysis of 237 patients undergoing whole-brain radiotherapy for brain metastases (2017–2021), receiving over 80% of treatments in the morning or afternoon. Survival analyses utilized Kaplan–Meier curves. Setting/Participants: Single-institution study involving patients receiving whole-brain radiotherapy. Collected demographic, disease, and socioeconomic parameters from electronic medical records. Results: Morning treatment (n=158) showed a trend towards improved overall survival vs. afternoon (n=79), median survival 158 vs. 79 days (p=0.20, HR=0.84, CI95% 0.84–0.91). Subgroup benefits for morning treatment in females (p=0.04) and trends in controlled primary disease (p=0.11) and breast cancer metastases (p=0.08). SDoH-based disparities observed, with Black and lower-income patients exhibiting diminished circadian influence. Conclusions: Emphasizes chronobiological factors' relevance in brain metastases radiation therapy. Morning treatment correlates with improved survival, particularly in specific subgroups. Identifies potential circadian influence disparities based on SDoH, laying a foundation for personalized cancer therapy and interventions synchronizing circadian rhythms for enhanced treatment efficacy.

Aging and obesity make humans more prone to cardiovascular and metabolic syndrome diseases, leading to several serious health conditions, including dyslipidemia, high blood pressure, and sleep disturbance. Hyperlipidemia means elevated blood lipid levels, including cholesterol and triglycerides. This study aimed to explore the hypolipidemic effect of fermented citrus lemon juice using a hyperlipidemic hamster model. Sugar-free lemon juice’s fermentation was optimized, and the characteristics of fresh and fermented lemon juice (FLJ) were evaluated and compared. In addition, tests were conducted to determine the appropriate hamster feed for the functional animal tests. Then, experiments were conducted to evaluate the hypolipidemic effect of the FLJ, which contained polyphenols and superoxide dismutase-like activity, on a hyperlipidemic hamster model. This study’s pre-fermentation efficiency evaluation found that 21–30 days of bacterial DMS32004 and DMS32005 fermentation of fresh lemon juice provided the best fermentation benefits. In addition, the fermentation evaluation showed that a sugar-free fermentation method provided FLJ with the best benefits. Results showed that the absorption and utilization efficiency of FLJ was higher compared with the unfermented lemon juice. After six weeks of feeding, the total cholesterol and triglyceride values in the blood and liver of the FLJ treatment groups were de-creased compared with the high-fat diet (HFD) group. In addition, the blood low-density lipoprotein cholesterol levels were significantly reduced in the FLJ treatment groups compared with the HFD group. In contrast, the blood high-density lipoprotein to low-density lipoprotein cholesterol ratio increased considerably in the FLJ treatment groups, and the total to high-density lipoprotein ratio was significantly lower than in the HFD group. Compared with the HFD group, the total cholesterol content in the FLJ treatment groups’ feces increased significantly. This study demonstrated that the sugar-free fermentation method and fermentation cycle management provided FLJ with the potential to regulate blood lipids. Further research and verification will be carried out to isolate specific substances from the FLJ and identify their mechanisms of action.

Since the implementation of the Materials Genome Project by the Obama administration in the United States, the development of various computational materials databases has fundamentally expanded the choices of industries such as materials and energy. In the field of thermoelectric materials, the thermoelectric figure of merit ZT quantifies the performance of the material. From the viewpoint of calculations for vast materials, the ZT values are not easily obtained due to their computational complexity. Here, we show how to build a database of thermoelectric materials based on first-principles calculations for the electronic and heat transport of materials. Firstly, the initial structures are classified according to the values of bandgap and other basic properties using the clustering algorithm K-means in machine learning, and high-throughput first principles calculations are carried out for narrow-bandgap semiconductors which exhibiting potential thermoelectric application. The present framework of calculations mainly includes deformation potential module, electrical transport performance module, mechanical and thermodynamic properties module. We have also set up a search webpage for the calculated database of thermoelectric materials, providing searching and viewing the related physical properties of materials. Our work may inspire the construction of more computational databases of first-principle thermoelectric materials and accelerate research progress in the field of thermoelectrics.

The movement of liquid droplets on the energy gradient surface has attracted extensive attention. Inspired by biological features in nature, such as the periodic spindle-shaped nodes in spider silks and conical-like barbs of cacti, the structure-property-function relationship of multifunctional gradient surfaces. In this study, a series of specific patterns are fabricated by 3D printing technology, followed by modification via the atmospheric pressure plasma treatment and liquid phase chemical deposition, resulting in enhancing the ability of water droplets of 5μL to travel 18.47mm on a horizontal plane and 22.75mm against gravity up to 20° tilting angle. Additionally, analysis techniques have been employed including contact angle analyzer, ESCA and laser confocal microscope to evaluate the sample performance. This work could further be applied to many applications related to microfluidic devices, drug delivery and water/fog collection.

Skeletal muscle is a specialized tissue consisting of nondividing and multinucleated muscle fibers. Skeletal muscle-specific myostatin (MSTN) is a secreted protein that acts as a negative regulator of muscle mass by inhibiting proliferation and differentiation of myoblasts. In this study, we established a screening platform to monitor myostatin promoter activity in rat L8 myoblasts. Extract of Glycyrrhiza uralensis (GUE), an oriental herbal medicine, was identified through this screening platform and, the active fractions of GUE were identified by process-scale liquid column chromatography system. For in vivo study, the GUE as a feed additive was investigated in growth-finishing pigs. The results showed that GUE significantly increased body weight, carcass weight and lean content in pigs. Microbiota analysis indicated that GUE did not affect the composition of gut microbiota in pigs. In summary, this established rodent myoblast screening platform was used to identify a myogenesis-related phytogenic, GUE, and further demonstrated that the active fractions inhibited MSTN expression. These finding suggest a novel application for GUE in growth performance enhancement through modulation of MSTN expression. Furthermore, this established screening platform has great potential for identification and evaluation of a wide variety of phytogenics involving in myogenesis.

The advancement of bioconcrete over cementitious composites has brought us to the application of microbes in the field of construction materials. Certain microbes like bacteria, algae, and fungi have been discussed in the review. The purpose of applying these microbes in the matrix is mainly to enhance the concrete’s strength and other properties such as durability, resistance, and self-healing ability. As these microbes are able to induce calcite biomineralizations, the process is also known as Microbiologically Induced Calcite Precipitation (MICP). Some known microorganisms with their mentioned ability are Bacillus subtilis and Bacillus cohnii (bacteria), Chlorella vulgaris and Spirulina platensis (algae), and Trichoderma reesei, Aspergillus niger, and Neurospora crassa (fungi). The paper provides a “state-of-the-art” review of research into the effects of bioconcrete and discusses the overall methodologies of every medium with their physiological, physicochemical and bioengineering properties in the light of recent researches done so far in the same field.

To accurately identify high-quality functional wood with superior mechanical properties and enhance its durability, it is imperative to understand the relationships between the physical and mechanical attributes of diverse wood types. Presently, there exist issues related to accuracy, efficiency, and differentiation in studying these performance correlations. The Liang Kleeman (L-K) information flow theory, a causative analytical approach rooted in fundamental physics principles, offers swift computational capabilities. Furthermore, the coefficient of variation in L-K information flow quantitatively gauges the intensity of causal effects. Therefore, this article adopts a causal artificial intelligence perspective and introduces a wood performance analysis method based on L-K information flow.This study focuses on four Chinese fir varieties, including fast-growing Chinese fir (YKS), red heart Chinese fir (CSH, XXH), and iron heart Chinese fir (XXT). By computing and comparing variation coefficients of L-K information flow for various physical properties and their impact on mechanical properties, causal relationships between these properties are elucidated. These findings are then applied to predict wood mechanical properties, achieving a remarkable maximum accuracy of 90%.In the future, these findings will prove invaluable for the selection of high-quality wood and for improving the manufacturing process to prolong the service life of functionalized wood.

Background: People with Down syndrome (DS) have a trisomy of chromosome 21 and marked deficits in verbal memory but relatively preserved visuospatial perception. Verbal memories are related to semantic knowledge. Little is known about the organization of semantic knowledge in people with DS, which was the aim of this study. Aims: The extent of false memory in people with DS was examined. Possible differences in the number of false memories induced by nominal and verbal themes were examined. Methods and Procedures: In the study phase, ten word lists with semantically related associates were presented. In the recognition phase, participants made judgments on whether each word had been represented previously as semantically related lures, old words, and semantically unrelated new words. Outcomes and Results: Differences in the processing of nominal and verbal theme-related lures were observed among people with DS. When processing nominal theme-related lures, people with DS showed delayed false positives. When processing verbal theme-related lures, people with DS showed no differences compared to controls. Similar patterns have been observed in people with DS when processing nominal theme-related associates and verbal theme-related associates. People with DS have delayed recognition of associates. When processing unrelated words, they showed significantly higher false positives than controls for both nominal and verbal eliciting themes. Further analyses of the themes revealed differences in false positives across syntactic categories among groups. Conclusions and Implications: People with DS showed a delayed recognition of associates and deviance in recognizing unrelated words in the nominal and verbal theme categories. People with DS were delayed in terms of nouns, but deviated with verbs in associated and unrelated words. Additionally, people with DS showed distinct patterns in processing five nominal lures and three verbal lures, suggesting that they formed false memories differently based on distinct syntactic categories. Thus, it was concluded that people with DS develop a deviant semantic structure. Category-based interventions for people with DS should be implemented in order to improve their semantic knowledge through lexical connections.

In cosmology, the cosmic curvature $K$ and the cosmological constant $\Lambda$ are two most important parameters, whose values have strong influence on the behavior of the universe. By analyzing the energy-momentum tensor and equations of state of ideal gas, scalar, spinor and vector potential in detail, we find that the total mass density of all matter is always positive, and the initial total pressure is negative. Under these conditions, by qualitatively analyzing the global behavior of the dynamical equation of cosmological model, we get the following results: (i) $K= 1$, namely, the global spatial structure of the universe should be a 3-dimensional sphere $S^3$. (ii) $0\le\Lambda < 10 ^ {-24} {\rm ly} ^ {-2}$, the cosmological constant should be zero or an infinitesimal. (iii) $a(t)>0$, the initial singularity of the universe is unreachable, and the evolution of universe should be cyclic in time. This means that the initial Big Bang is impossible at all. Since the matter components considered are quite complete and the proof is very elementary and strict, these logical conclusions should be quite reliable. Obviously, these conclusions will be much helpful to correct some popular misconceptions and bring great convenience to further research other problems in cosmology such as property of dark matter and dark energy.

The description of the microscopic world in quantum mechanics is very different from that in classical physics, and there are some points of view that are contrary to intuition and logic. The first is the loss of reality, the behavior of micro particles shows randomness and hopping. The second is the loss of certainty, the conjugate physical variables of a system cannot be determined synchronously, they satisfy the Heisenberg uncertainty principle. The third is the non-local correlation. The measurement of one particle in the quantum entanglement pair will change the state of the other entangled particle simultaneously. In this paper, some concepts related to quantum entanglement, such as EPR correlation, quantum entanglement correlation function, Bell's inequality and so on, are analyzed in detail. Analysis shows that the mystery and confusion in quantum theory may be caused by the logical problems in its basic framework. Bell's inequality is only a mathematical theorem, but its physical meaning is actually unclear. The Bell state of quantum entangled pair may not satisfy the dynamic equation of quantum theory, so it cannot describe the true state of microscopic particles. In this paper, the correct correlation functions of spin entanglement pair and photonic entanglement pair are strictly derived according to normal logic. Quantum theory is a more fundamental theory than classical mechanics, and they are not parallel relation in logic. However, there are still some unreasonable contents in the framework of quantum theory, which need to be improved. In order to disclose the real relationship between quantum theory and classical mechanics, we propose some experiments which show the wave-particle duality simultaneously and provide intuitionistic teaching materials for the new interpretation of quantum theory.

To enhance industrial competitiveness and increase productivity, every country has strived to create a smart factory by introducing technologies such as Internet of Things, big data and artificial intelligence into production line and build cyber-physical system for the purpose of promoting manufacturing efficiency. For mission assignment, production line management or manufacturing field analysis, the location information of employee, machine and material is very essential. To promote manufacturing efficiency, of course, the location information became more important. A Bluetooth low energy (BLE) positioning system for the manufacturing is developed in this research. A "Tag tracking" mechanism is addressed and adopted, which uses Beacon to catch the location information and a BLE receiver is also used to receive the broadcasting information from Beacon. The position information from the BLE receiver will be compared with the data in the database for calculating the location of the target. The status of the target may also be obtained by using the data from the BLE receiver. Comparing with the mobile device, this method can reduce energy consumption and make the maintenance simple and easy. In the real applications, the target may not be limited to human. The "Regional label positioning technology" is also investigated in this research. Defining a suitable zone location and arranging BLE receiver location, and positioning analysis theory are the key factors included in this developed technology. The developed system will be tested for real industry applications. The test results show that the feasibility of this technology.

Floating Offshore Wind Turbine (FOWT) is an innovative technology with little industry guidance for its hull design. Various FOWT floaters with different hull shapes claim to support the same turbines. Structural integrity and material expense analyses of different pontoon shapes were conducted, and it was found that some configurations, such as those with every two columns connected by both pontoon and bracing, have advantages over others. However, it is important to note that the choice of pontoon shape should be based on the wave loading conditions the floater will be exposed to. While a T-shaped pontoon provides a cost-effective solution under certain wave loading scenarios, it may not be the best option for all conditions. Specifically, ring pontoon designs with full bracing were found to be necessary for withstanding certain wave loads. Therefore, it is important to consider different Dominant Load Parameters (DLP) and ensure that a FOWT floater can withstand all applicable DLPs. An uneven hexahedral column shape, which combines the best attributes of square and round shapes, is proposed as a better alternative to cylindrical columns. It offers ease of manufacture and reasonably low drag. Bracing is found to be necessary for withstanding the wind turbine’s incurred moment and forces. The conclusion is that platform design should prioritize manufacturing costs and strength over maximizing hydrodynamic performance.

Tumorigenesis is a complex biological phenomenon that includes extensive genetic and phenotypic heterogeneities and complicated regulatory mechanisms. In the recent few years, our studies demonstrate that tumor-initiating cells are similar to neural stem/progenitor cells in regulatory networks, tumorigenicity and pluripotent differentiation potential. In the review, I will make further discussion on these observations and propose a rule of cell biology by integrating these findings with evidence from developmental biology, tumor biology and evolution, which suggests that neural stemness underlies two coupled cell properties, tumorigenicity and pluripotent differentiation potential. Tumorigenicity and phenotypic heterogeneity in tumor is a result of acquirement of neural stemness in cells. The neural stemness property of tumor-initiating cells can hopefully integrate different concepts/hypotheses underlying tumorigenesis. Neural stem cells/neural progenitors and tumor-initiating cells share regulatory networks; both exhibit neural stemness, tumorigenicity and differentiation potential; both are dependent on expression or activation of ancestral genes (the atavistic effect); both rely primarily on aerobic glycolytic metabolism; both can differentiate into various cells or tissues that are derived from three germ layers, resembling severely disorganized or more severely degenerated process of embryonic development; both are enriched in long genes with more splice variants that provide more plastic scaffolds for cell differentiation, etc. The property of neural stemness might be a key point to understand tumorigenesis and pluripotent differentiation potential, and possibly explain certain pathological observations in tumors that have been inexplicable. Therefore, behind the complexity of tumorigenesis might be a general rule of cell biology, i.e., neural stemness represents the ground state of cell tumorigenicity and pluripotent differentiation potential.

The magnetic field of the earth plays an important role in the ecosystem, and the magnetic field of celestial bodies is also important in the formation of cosmic large-scale structures, but the origin and evolution of the celestial magnetic field is still an unresolved mystery. Many hypotheses to explain the origin have been proposed, but there are some insurmountable difficulties for each one. At present, the theory widely accepted in scientific society is the dynamo model, it says that, the movement of magnetofluid inside celestial bodies, which can overcome the Ohmic dissipative effect and generate persistent weak electric current and macroscopic magnetic field. However, this model needs an initial seed magnetic field, and the true values of many physical parameters inside the celestial body are difficult to obtain, and there is no stable solution to the large range of fluid motion. These are all difficulties for the dynamo model. Furthermore, it is difficult for the dynamo to explain the correlation between the dipole magnetic field and angular momentum of a celestial body. In this paper, by calculating the interaction between spin of particles and gravity of celestial body according to Clifford algebra, we find that a rotational celestial body provides a field $\Omega^\alpha$ for spins, which is similar to the magnetic field of a dipole, and the spins of charged particles within the celestial body are arranged along the flux line of $\Omega^\alpha$, then a macroscopic magnetic field is induced. The calculation shows that the strength of $\Omega^\alpha$ is proportional to the angular momentum of the celestial body, which explains the correlation between the magnetic intensity and angular momentum. The results of this paper suggest that further study of the effects of internal variables such as density, velocity, pressure and temperature of a celestial body on $\Omega^\alpha$ may provide some new insights into the origin and evolution of celestial magnetic field.

This study establishes a multivariate function model for natural human load carrying walking in some typical scenarios like college equipments and materials relocation for students. For classified materials relocation needs and constraints, we obtain the relationship between walking speed and load weight for single person, as well as the time cost for different round trips. By establishing an integer programming model with the minimum total transportation time cost and quality assurance as the objective function and the requirements of negative weight and speed as the constraints conditions, we reach the optimal item allocation methods considering time cost and shelf life were obtained. We discover that there is an approximate linear relationship between the change in natural walking speed and travel time when the load is small, thus obtaining the time cost of student transportation under different round-trip situations. The Monte Carlo simulation algorithm is used to obtain the optimal allocation scheme that meets the efficiency and quality requirements. The analysis methods and results can be used as guidance for task scheduling optimization for material relocation in educational organizations as well as commercial agencies.

In a single-center, retrospective study, 22 cases were enrolled and divided into two groups: those who underwent surgical wide excision (group A) and those who did not (group B). The study included 13 cases in group A and 9 cases in group B. In group A, 6 cases solely underwent surgical wide excision, while 7 cases received additional treatments like radiotherapy or chemotherapy. Conversely, in group B, 4 cases received chemotherapy, 4 cases received radiotherapy, and 1 case was managed through observation alone. The mean follow-up time was 60.15 months in group A and 43.44 months in group B, with no significant difference observed. In group A, 9 cases resulted in mortality, whereas 6 cases died within the follow-up period in group B. Lesion-free intervals post-operation were observed predominantly in group A, while 7 cases in group B never experienced freedom from skin lesions. Kaplan-Meier survival curve analysis demonstrated a significant difference between the survival curves of the two groups (P = 0.046). Among non-HIV Kaposi’s sarcoma patients, surgical wide excision appears to have a role in treatment. Patients in group A exhibit a more favorable outcome in the survival curve analysis.

A Shape Memory Alloy (SMA) enabled Overtopping Wave Energy Converter (OWEC) that maximizes its overtopping discharge, and thus energy output under different wave conditions is presented. Among all the parameters affecting the overtopping discharge rate, the crest freeboard height is the most influential one to control the overtopping discharge rate and the stored overtopping volume behind it. Currently, all the OWEC crest freeboard heights are fixed by design to maximize the discharge rate on one particular sea state. In the present study, we show that the SMA can adjust the crest freeboard height through a control system based on the sea state and achieve an optimal overtopping discharge rate. A scaled OWEC model is built in the lab with its crest freeboard height controlled by springs made of SMA. The length (and thus tension) of the springs is controlled by temperature changes by changing the passing current through the springs. By adjusting the length of the springs based on the incoming wave condition, we adjust the freeboard to an optimal height known to generate a maximum overtopping discharge rate for energy conversion. This smart material-enabled design can maximize the overtopping discharge and thus the output power of the OWEC under various wave conditions. Furthermore, the simplicity of using SMA springs as the actuator leads to the minimum number of moving mechanical parts, which can remarkably decrease maintenance costs. As the proof of concept, two types of tests are conducted in the laboratory using the same OWEC model under several random wave trains generated from spectra with different significant wave heights - one type with a fixed crest freeboard height and the other type featuring the adjustable crest freeboard height controlled by the springs. The substantial increase of harvested output power in the OWEC with the adjustable crest freeboard height may pave the way for more efficient wave energy conversion systems.

A number of epidemiological studies have implicated elevated iron levels with higher risks of cardiometabolic diseases, including the metabolic syndrome (MetS). MetS is a pathologic clustering of metabolic derangements characterized by central obesity, insulin resistance, hypertension, and dyslipidemia, which can all lead to increased cardiovascular disease morbidity and mortality. However, it remains unclear whether a causal association exists between higher iron status and MetS and its associated risk components. Using the data from the Taiwan Biobank (TWB) (19,012 males; 42,340 females) and of the European Whites from the UK Biobank (UKB) (128,549 males; 142,817 females), we first constructed ethnic- and sex-specific hemoglobin-polygenic risk scores (Hb-PRS) as instrumental variable (IV) for iron status with the Hb-associated SNPs we previously identified from genome-wide association studies (GWAS). We then conducted Mendelian randomization (MR) analyses to elucidate the causal role of elevated iron (either Hb-PRS quintiles or continuous Hb-PRS) on various metabolic components. MR-Egger regressions determined the potential pleiotropic effects of the constructed Hb-PRSs, while the causal relationship of Hb-PRS with anemia served as a control in the analyses. The mean Hb concentration range corresponding to the Hb-PRS quintiles is relatively narrow in both UKB (14.91-15.21 g/dL for males and 13.39-13.71 g/dL for females) and TWB (14.79-15.28 g/dL for males and 12.78-13.21 g/dL for females). In these windows of Hb-PRSs, we found differential associations of Hb-PRS with diabetes (T2D) or hyperglycemia (HGY) as compared to other MetS components. The highest quintiles of Hb-PRSs were causally associated with greater risks of hypertension (HTN) and hypertriglyceridemia (DLP) (i.e., [Taiwanese HC males: Q5 vs. Q1 ORHTN = 1.10 (1.00–1.21), p = 0.0473, Q4 vs. Q1 ORDLP = 1.10 (1.00–1.22), p = 0.0485; European White males: ORHTN = 1.05 (1.01–1.09), p = 0.0194, ORDLP = 1.04 (1.00–1.08), p = 0.0468]). Interestingly, we obtained a consistent negative causal association between increasing Hb-PRS quintiles and T2D or HGY risk across all sex subgroups (i.e., [Taiwanese HC females: ORHGY = 0.89 (0.84–0.95), 0.88 (0.83–0.94), 0.87 (0.82–0.93), 0.86 (0.81–0.92) from Q2 to Q5; European White females: ORHGY = 0.92 (0.87–0.98), 0.91 (0.86–0.97), 0.93 (0.87–0.98), 0.87 (0.82–0.93) from Q2 to Q5; all p &lt; 0.05]. The positive causal relationships between Hb-PRSs and diastolic blood pressure (DBP) and triglycerides (TG) but inverse causal association with glucose (GLU) and glycated hemoglobin (HbA1c) further corroborated such findings. There is, however, a lack of causal association with central obesity (CO), while a U-shaped type of causality was observed for gout (GT) or hyperuricemia (HUA). Sensitivity analyses, which excluded subjects based on self-reports of health conditions or medications and hospital episode statistics data, revealed similar results. Our MR studies confirm a modest causal relationship between propensity of elevated iron status and increased risk of HTN and DLP. We have further observed that modestly lower iron levels causally contribute to the development of T2D. Further validation and elucidation of the underlying biological mechanisms are highly warranted.

Taiwan's bed and breakfast (B&B) development has been more than 25 years ago, from the first generation of retirement to the B&B industry, serving tourists from all over the world accom-modation, providing breakfast and accommodation mode to the present, after the change of employees from the second generation, more and more attention is paid to the cultivation and cultivation of business ability. With the advent of the era of AI technology networking, the ca-pabilities required for B&B operation are more focused on all aspects of service, and the good marketing ability of B&B can promote a green chimney-free tourism economy, which is also a favorite industry of various governments and the public. This study explores the basic vocational competency indicators required for running a B&B, with (1)EQ emotion management skills, (2)Financial management ability, (3)(SK) technical skills, and (4)Marketing and promotion management capabilities. Through the study method, the K-S Z test was determined by the con-sensus conclusion of expert reliability and validity p value

The objective of this study is to investigate the use of excavation behavior prediction and analysis software in the field of civil en-gineering. PLAXIS and SoilWorks, widely used in the engineering and academic communities, were employed as research tools for analyzing gravel layers and deriving appropriate ranges of soil elastic modulus for different software programs. By collecting excavation cases in the Xindian area of New Taipei City, Taiwan, and conducting deep excavation analysis using the displacement of retaining walls, this study provides recommended ranges for localized selection of soil elastic modulus. The suggested range for PLAXIS is 7,840 N/m² to 9,800 N/m², while Soil-Works suggests a range of 2,450 N/m² to 3,430 N/m². These ranges allow for reasonable estimation of maximum deformations during the final excavation stage. Based on the research findings, it is recommended that engineers refer to the provided ranges when selecting soil elastic modulus for excavation analysis in gravel layers using different soft-ware programs in the Xindian area of Taiwan to improve the accuracy of deformation predictions during the final excavation stage. These results serve as important references for engineers and contribute to the effective prediction and management of excavation behavior in civil engineering projects.

Aluminum alloy (Al6061) sheet micro-hole processing is extensively used in smartphones, tablet PC, and smart wearable devices. The micro-hole processing is commonly performed using laser, micro drilling, microstamping, micro discharge, and chemical etching technologies. Micro-stamping technology is characterized by precision and rapid processing, but the precision positioning of the punch head and lower die is one of the major difficulties in micro-hole stamping, especially in manufacturing array micro-holes. This study used stamping without die technology. This technology uses an array punch head to punch the lower die holes on the base, then performs array micro-hole stamping. The experimental results show that a micro-hole array with 37 micro-holes were successfully manufactured and can be reproduced many times. Tapered array micro-holes with a high aspect ratio can be manufactured using this stamping without die technology; the micro-hole depth can be 260μm, the inlet diameter is 116μm, and the outlet diameter is 25μm. This study has successfully developed the feasibility of array micro-hole stamping technology.

A novel flexible humidity sensor, incorporating gold nanoparticles (Au NPs) and a trifunctional organosilica compound, has been developed through the integration of sol-gel processing, free radical polymerization, and self-assembly techniques. The trifunctional organosilica was initially synthesized by modifying (3-mercaptopropyl)trimethoxysilane (thiol-MPTMS) with 3-(trimethoxysilyl)propyl methacrylate (vinyl-TMSPMA). Subsequently, a hydrophilic polyelectrolyte, [3(methacryloylamino)propyl]trimethyl ammonium chloride (MAPTAC), was grafted onto the MPTMS-TMSPMA gel. The Au NPs were assembled onto the thiol groups present in the MPTMS-TMSPMA-MAPTAC gel network. The compositional and microstructural properties of the Au NPs/MPTMS-TMSPMA-MAPTAC composite film were investigated utilizing Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). The presence of thiol groups and mesoporous silica skeletons ensured the stability of the humidity-sensing film on the substrate under highly humid conditions, while the hydrophilic groups functioned as humidity-sensitive sites. This innovative humidity sensor demonstrated high sensitivity, acceptable linearity, minimal hysteresis, and rapid response time across a broad range of working humidity levels. Based on the complex impedance spectra analysis, hydronium ions (H₃O⁺) were determined to govern the conductance process of the flexible humidity sensor.

Background: People with Williams syndrome (WS) are characterized with hypersociability, fluency in languages, and advantageous face-processing skills, leading to the proposal of a social module. Previous studies on the mentalizing abilities of people with WS using two-dimensional pictures and mindreading from eyes, including normal-like, delayed, and deviant behaviors, have yielded mixed results. This study thus examined the mentalizing ability of people with WS through structured computerized animations of false belief tasks to investigate whether inferences about other people’s minds can be improved in this population. Method: Participants were shown animations with unexpected location and content changes. After viewing each animation, participants had to answer four types of questions: character identification, reality, memory, and false belief. Their responses were recorded and analyzed. Results: Comprehension of false belief was observed in 4-year-old healthy children, whereas children with WS showed unsuccessful comprehension of false belief (until they attained a mental age of 5.3 years), suggesting an improvement in theory of mind resulting from viewing structured computerized animations. This age is earlier than that reported by previous studies for using theory of mind to pass false belief tests (8.5 years old), even challenging the age at which individuals failed to pass the tests (12.10 years old). Conclusions: Structured computerized animations enhanced the mentalizing ability of people with WS to a certain extent. Compared to the typically developing controls, people with WS presented with a lower developmental level in processing false belief tasks. The educational implication of this study is to develop computerized social skills interventions for people with WS.

Because imbalanced power will cause the loss of the propulsion motor of the railway vehicle, and the increase in temperature will shorten the service life of the electric vehicle. Not only this, but also increase the cost of electricity and maintenance. In the past, the industry only focused on methods to improve power quality such as load capacity, relay setting, and harmonic resolution. Now, the consider of three-phase unbalance rate (TPUR) must be applied. I propose special transformers wiring (STW) to improve the three unbalance rates and provide different transformer wiring methods. According to the IEEE Committee, in the future, power companies will need to install balanced relay stations to improve three-phase unbalance rate. the internal regulations of Taipower must be less than 4.5% (voltage unbalance rate (NPSUR)of 2.5% and motor temperature rise of 12.5%). the derivation of the transformer "three-phase unbalance rate" model is the focus of the railway system. This research is based on the model derivation of different wiring methods to improve the hot problem caused by the three-phase imbalance and improve the service life of the train. And pointed out that Scott, Le-Blanc, Modified-Woodbridge three wiring methods can be applied to future railway system routes to improve the three-phase unbalance rate, in line with the IEEE standard of less than 2%.

Agriculture is an industry that heavily relies on the environment. The increasing frequency of ex-treme disasters attributable to climate change has adversely affected agricultural land and dis-rupted the stability of the supply of agricultural products. Therefore, we implemented a research program focused on current strategies for adapting to agricultural meteorological disasters. The primary goal was to actively promote disaster prevention information and techniques through information platforms and applications and to provide refined forecasting and an early warning system to enhance preparedness for and recovery from agricultural disasters. This initiative can transform passive mitigation into dynamic action by disseminating crucial information to farmers. We integrated meteorological data and crop characteristics to develop disaster prevention strate-gies for the predisaster, during-disaster, and postdisaster stages to empower farmers to implement autonomous disaster prevention, ensuring their profitability and minimizing the impact of disas-ters. This paper presents an agricultural disaster prevention system involving cross-disciplinary collaboration to establish an early warning system for crop disasters. However, the effectiveness of the early warning system relies on the availability of complete meteorological and crop infor-mation, necessitating high-density agricultural meteorological stations, refined weather forecast services, historical crop damage data, and ongoing research and development on disaster preven-tion technology. In the system, a diversified social media interface is used to provide local farmers with weather forecast information. When impending disasters are identified, the platform acti-vates disaster prevention measures to reduce agricultural losses. This article paper introduces Taiwan’s agricultural disaster prevention system as a complete disaster prevention strategy.

Chimeric antigen receptor (CAR) T-cell therapy has greatly improved outcomes for patients with relapsed or refractory hematological malignancies. However, challenges such as treatment resistance, relapse, and severe toxicity still hinder its widespread clinical application. Traditional transcriptome analysis has provided limited insights into the complex transcriptional landscape of both leukemia cells and engineered CAR-T cells, as well as their interactions within the tumor microenvironment. However, with the advent of single-cell sequencing techniques, a paradigm shift has occurred, providing robust tools to unravel the complexities of these factors. These techniques enable unbiased analysis of cellular heterogeneity and molecular patterns. These insights are invaluable for precise receptor design, guiding gene-based T cell modification, and optimizing manufacturing conditions. Consequently, this review utilizes modern single-cell sequencing techniques to clarify the transcriptional intricacies of leukemia cells and CAR-Ts. The aim of this manuscript is to discuss the potential mechanisms that contribute to the clinical failures of CAR-T immunotherapy. We will examine the biological characteristics of CAR-Ts, the mechanisms that govern clinical responses, and the intricacies of adverse events. By exploring these aspects, we hope to gain a deeper understanding of CAR-T therapy, which will ultimately lead to improved clinical outcomes and broader therapeutic applications.

Currently, urban renewal activities in China are booming. And promoting the renovation of public buildings is the key due to its large scale, high cost and significant impact to the nature and social environment. To reduce the ambiguity and uncertainty in evaluating the potential for renewal of existing public buildings, a renewal potential evaluation model combining game theory combination weighting method and cloud model theory is proposed. The paper constructs a comprehensive evaluation index system based on relevant standards and literature. Game theory is used to optimize the weights obtained by AHP and entropy weight methods to obtain a combined weight. MATLAB programming is used to calculate the comprehensive cloud parameters of the evaluation index for the potential renewal of existing public buildings and therefore generate cloud Graphs. Through case study in Nanjing of China, it has been demonstrated that the combination empowerment cloud model can objectively reflect the relationship between the fuzziness and randomness of evaluation indicators for public building renewal potential. The expression of cloud Graphs can intuitively reflect the magnitude of renewal and renovation potential and the degree of uncertainty in evaluation results. The research result provides useful references for the sustainable utilization of building resources in the era of building.

Biodiversity plays an important role in maintaining the ecological balance of the earth. The study of traditional knowledge related to biological resources is a hot issue in the field of international biodiversity conservation. Xishuangbanna is a key area of biodiversity and a cultural hotspot of international significance. According to the Technical Regulation for Classification, Investigation, and Inventory of Traditional Knowledge Relating to Biological Diversity issued by the Ministry of Ecology and Environment, we investigated and catalogued the traditional knowledge related to biodiversity of the Jino people who have lived in Xishuangbanna for generations, and collected 490 entries of traditional knowledge related to biodiversity of the Jino people. Drawing on the traditional knowledge diversity index calculation method proposed by Wang Guoping, the overall traditional knowledge α-diversity index of the Jino people is 0.63, indicating that the richness of the traditional knowledge of the Jinuo people is relatively high. The traditional culture related to biodiversity, the traditional knowledge related to agricultural genetic resources, and the traditional technology related to the sustainable utilization of biological resources are relatively rich and diverse. The diversity index is 0.86, 0.82 and 0.79 respectively. In addition, Xishuangbanna has invested a lot of energy in biodiversity protection, including the establishment of nature reserves, botanical gardens, zoos, ecological tea gardens and other species reserves, the promulgation of laws and policies related to biodiversity protection, and has achieved remarkable results in in-situ protection and ex-situ protection. On the basis of analyzing the progress and achievements of biodiversity conservation in Xishuangbanna, this study points out that Xishuangbanna faces challenges such as the loss of traditional knowledge, insufficient conservation efforts, and great changes in land use, and puts forward corresponding suggestions.

This study presents a vibration control using actively tunable vibration absorbers (ATVA) to suppress vibration of a thin plate. The ATVA’s is made of a sandwich hollow structure embedded with the electrorheological fluid (ERF). ERF is considered to be one of the most important smart fluids and it is suitable to be embedded in a smart structure due to its controllable viscosity property. ERF’s apparent viscosity can be controlled in response to the electric field and the change is reversible in 10 microseconds. Therefore, the physical properties of the ERF-embedded smart structure, such as the stiffness and damping coefficients, can be changed in response to the applied electric field. A mathematical model is difficult to be obtained to describe the exact characteristics of the ERF embedded ATVA because of the nonlinearity of ERF’s viscosity. Therefore, a fuzzy modeling and experimental validations of ERF-based ATVA from stationary random vibrations of thin plates are presented in this study. Because Type-2 fuzzy sets generalize Type-1 fuzzy sets so that more modelling uncertainties can be handled, a semi-active vibration controller is proposed based on Type-2 fuzzy sets. To investigate the different performances by using different types of fuzzy controllers, the experimental measurements employing type-1 fuzzy and interval type-2 fuzzy controllers are implemented by the Compact RIO embedded system. The fuzzy modeling framework and solution methods presented in this work can be used for design, performance analysis, and optimization of ATVA from stationary random vibration of thin plates.

This paper reassesses the detrimental effect on fatigue performance due to thicker sections based on extensive fatigue strength test database, taken from research program worldwide over the past half of a century in offshore oil &amp; gas and renewable industry. The data entries in the database have been evaluated to ensure its data integrity. Statistical analyses on these S-N data are performed with or without the thickness correction at different exposure level to corrosive environment, in order to re-evaluate the suitability of current standards in regard to the thickness effect. The study has concentrated on T-joint, transverse butt welded joint and tubular joint as these are the most commonly used joint types in the offshore wind industry. The analysis indicates general agreement of fatigue strength with the thickness effects in current standard for in air conditions but great conservatism for corrosive environment.

The concept of Design Fatigue Factors (DFFs) was introduced for providing desired level of safety in structural fatigue design, often associated with damage calculated from S-N curves. Calculation of fatigue damage from S-N curves can be affected by multiple factors, e.g. types of weld class, corrosion condition, loading conditions, stress concentration on different geometries etc. Each of them can be subject to different level of uncertainties. This study intends to recalibrate the DFFs from a detailed reliability analysis by investigating the probabilistic models derived from the database of S-N curves that has been most frequently used in offshore wind industry. The results of such study indicate that the DFFs can be reduced substantially for the corrosive environmental fatigue models from current standards to the same level of target reliability.

Dry eye syndrome (DES) has become increasingly prevalent due to the prolonged use of digital devices in modern society. Individual supplementation with lutein or docosahexaenoic acid (DHA) demonstrated potential benefits for eye health. This study aimed to investigate the effects of lutein plus DHA complex supplementation on DES, visual function, and memory in healthy individuals. Thirty-four participants, aged 40~60 years, received lutein/DHA complex supplements (containing 10 mg free-form lutein, 200 mg DHA, 30 mg red algae extract (astaxanthin), phosphatidylserine, and vitamin A) for 12 weeks. Ophthalmological examinations and memory tests were carried out, and a questionnaire was administered at weeks 0, 6, and 12 of the study. After 12 weeks of the intervention, the tear break-up time had significantly increased, and intraocular pressure (IOP) had significantly decreased. This suggests that lutein/DHA complex supplementation may reduce the IOP and offer potential benefits for DES, as indicated by improved tear stability.

Patients receiving hemodialysis are at risk of vascular access infections (VAIs) and particularly vulnerable to the opportunistic pathogen Staphylococcus aureus. Hemodialysis patients were also at increased risk of infection during the COVID-19 pandemic. Therefore, this study determined the change in the molecular and antibiotic resistance profiles of S. aureus isolates from VAIs during the pandemic compared with before. 102 S. aureus isolates were collected from VAIs between November 2013 and December 2021. Before the pandemic, 69 isolates were collected, 58%, 39.1%, and 2.9% from arteriovenous grafts (AVGs), tunneled cuffed catheters (TCCs), and arteriovenous fistulas (AVFs), respectively. The prevalence of AVG and TCC isolates changed to 39.4% and 60.6%, respectively, of 33 isolates during the pandemic. Sequence type (ST)59 was the predominant clone in TCC-methicillin-resistant S. aureus (MRSA) and AVG-MRSA before the pandemic, whereas the predominant clone was ST8 in AVG-MRSA during the pandemic. ST59 carrying the ermB gene was resistant to clindamycin and erythromycin. By contrast, ST8 carrying the msrA gene was exclusively resistant to erythromycin. The ST distribution for different VAIs changed from before to during the pandemic. The change in antibiotic resistance rate for different VAIs was closely related to the distribution of specific STs.

This paper proposes a parameter coordination optimization design of Power System Stabilizer (PSS) based on an improved Quasi-Affine Transformation Evolutionary (QUATRE) algorithm to suppress low-frequency oscillation and improve the dynamic stability of power system. To begin, the Simulated Annealing (SA) algorithm randomly updates the globally optimal solution of each QUATRE iteration and matches the inferior solution with a certain probability to escape the local extreme point. This new algorithm is first applied to power system. Second, Since damping ratio is one of the criteria to measure the dynamic stability of power system, this paper sets the objective function according to the principle of maximization of damping coefficient of electromechanical mode, and uses SA-QUATRE to search a group of global optimal PSS parameter combinations to improve the stability margin of the system as much as possible. Finally, the method's rationality and validity were validated by applying it to the simulation examples of IEEE 4-machine 2-area system with different operation states. The comparison with the traditional optimization algorithm shows that the proposed method has more advantages for multi-machine PSS parameter coordination optimization, and can restrain the low-frequency oscillation of power system more effectively and enhance the system stability.

Hepatocellular carcinoma (HCC) is the fifth most common type of cancer, and is the third leading cause of cancer-related deaths each year. It involves a multi-step progression and is strongly associated with chronic inflammation induced by the intake of environmental toxins and/or viral infections (i.e., hepatitis B and C viruses). Although several genetic dysregulations are considered to be involved in disease progression, the detailed regulatory mechanisms are not well defined. Homeobox (Hox) genes that encode transcription factors with homeodomains control cell growth, differentiation, and morphogenesis in embryonic development. Recently, more aberrant expressions of Hox genes were found in a wide variety of human cancer, including HCC. In this review, we summarize the currently available evidence related to the role of Hox genes in the development of HCC. The objective is to determine the roles of this conserved transcription factor family and its potential use as a therapeutic target in future investigations.

The composition and pattern of ecosystems are important factors determining the overall status and spatial differences of ecosystem service functions. However, under the background of differential land policies and ecological protection policies, research on the trend of ecological system pattern changes in the Fenhe River Basin is insufficient. Taking the upper and middle reaches of the Fenhe River Basin as the study area, based on long-term NDVI index and multi-period LUCC remote sensing images, this study used spatial statistics and time trend analysis methods to analyze the spatio-temporal dynamic changes of vegetation, land use, landscape pattern, and explored the impact of major driving factors on ecosystem changes. The results show that: (1) From 2010 to 2020, the vegetation cover in the upper and middle reaches of the Fenhe River Basin increased, with an annual NDVI increment of 0.003 (P<0.001). NDVI showed an increasing trend spatially, with significant statistics (P<0.001) and significant changes (P<0.05) in vegetation in high-altitude mountain areas, and the vegetation cover was mostly forests or grasslands. There was no significant change in vegetation cover in the low-lying urban agglomeration area. (2) From 2010 to 2020, the area of water bodies or wetlands in the study area significantly decreased, with 51.3% converted to arable land and 33.9% transferred to construction land, while only 2.2% remained as water bodies or wetlands. From 2015 to 2020, the trend of water body changes slowed down, with the proportions of conversion to arable land and construction land being 44.0% and 18.4% respectively, while the area of wetlands or water bodies remained at 16.3%. During the period of 2015-2020, the area of water bodies or wetlands converted to other land types increased by more than 14% compared to 2010-2015. This proportion reached more than 30% compared to the 13th Five-year Plan Period. (3) From 2010 to 2020, the spatial changes of landscape diversity (SHDI) and evenness (SHEI) of LUCC showed heterogeneous characteristics. In the high-altitude areas near the river basin boundary, the values of SHDI and SHEI were below 1.0. While in the low-altitude plain areas and urban areas with relatively frequent human activities, the values of SHDI and SHEI were above 1.0, and the values in urban areas could reach above 1.5. The evolution of ecosystem patterns in the upper and middle reaches of the Fenhe River Basin in the past decade has been clarified, providing a scientific basis for the construction and management of ecological environment governance and restoration projects in the Fenhe River Basin, and providing practical references for ecological protection and high-quality development practice in the Yellow River Basin.

3D Zernike moments based on 3D Zernike polynomials have been successfully applied to the field of voxelized 3D shape retrieval and have attracted more attention in biomedical image processing. As the order of 3D Zernike moments increases, both computational efficiency and numerical accuracy decrease. Due to this phenomenon, a more efficient and stable method for computing high-order 3D Zernike moments was proposed in this study. The proposed recursive formula for computing 3D Zernike radial polynomials combines the recursive calculation of spherical harmonics to develop a voxel-based algorithm for the calculation of 3D Zernike moments. The algorithm was applied to the 3D shape Michelangelo's David with a size of 150×150×150 voxels. As compared to the method without additional acceleration, the proposed method uses a group action of order sixteen orthogonal group and saving unnecessary iterations, the factor of speed-up is 56.783±3.999 when the order of Zernike moments is between 10 and 450. The proposed method also obtained an accurate reconstructed shape with the error rate (normalized mean square error) of 0.00 (4.17×10^-3) when the reconstruction was computed for all moments up to order 450.

Background: Gastric cancer (GC) is one of the leading malignancy diseases worldwide, especially in Asian. CAST is a potential oncogene in GC carcinogenesis process. The character of macrophage infiltration in GC microenvironment was also unaddressed. Methods: We first applied machine searching in gene candidate evaluation of GC. CAST expression was analyzed via the Human Protein Atlas (HPA) and Gene Expression Profiling Interactive Analysis 2 (GEPIA2) database. Protein-protein interaction (PPI) network was downloaded from STRING. We investigated the impact of CAST on clinical prognosis using Kaplan-Meier plotter. The correlations between CAST and Lgr5 and macrophage infiltration in GC was surveyed via TIMER 2.0. Finally, GeneMANIA was also used to evaluate the possible functional linkage between genes. Results: After machine-assisted searching, CAST expression was found signicant difference in the overall survival of GC patients. STRING revealed CAST related proteomics and transcriptomics associations, mainly about CAPN family. Moreover, CAST significantly impacts the prognosis of GC from other datasets validation. Notably, high CAST expression was correlated with worse overall survival in GC patients (hazard ratio = 1.59; logrank P = 9.4 x 10-8). CAST and Lgr5 expressions were both positively correlated with WNT 2 and WNT 2B. Among GC patients in several datasets, CAST and macrophage infiltration evaluated together showed no obvious trend toward poor clinical overall survival. Conclusion: CAST plays an important role in GC clinical prognosis and is associated with WNT 2/WNT 2B/Lgr5. Our study denmostrated that CAST in GC overall survival is regulated by macrophage infiltration.

Background: Cancer patients require cross-professional care during the diagnosis and treatment periods. Therefore, methods for effectively carrying out case management are essential to tumor care. Purpose: To investigate the effects of using the community software LINE Official Ac-count on oral cancer case management. Methods: An experimental design was used; 100 patients were randomly divided into two groups by using a computer-generated random number table. The experimental group used LINE Official Account, which gave them self-care information, timely messages, and one-on-one health-care consultations. The control group followed standard healthcare practices. Results: The experimental group was satisfied with the self-care information provided by LINE Official Account (86.9%), patients regularly checked the self-care information (89.4%) and would check the information when receiving a push notification (54.3%). Ten patients used the one-on-one consultation(20.0%). LINE Official Account had a significant effect on the rate of participation in support groups. Generalized estimating equations indicated a significant difference between the two groups regarding the overall quality of life over 7 days (P = 0.023). Conclusion: Community software applications used in oncological case management can improve self-management and empower, also enable tracking of long-term follow-up effectiveness and reinforce the case manager’s role as a family therapist. Therefore, this study recommends that case manager systems be incorporated into mobile applications to increase the sustainable management, accessibility, effectiveness, and satisfaction of oncological management systems. This study also provides the value of Sustainable Development Goals (SDGs) with Good Health and Well-being, and decreased social withdrawal among patients with oral cancer.

Simply Summary: Translation of new cancer treatments between pets and human were noticed in comparative oncological investigation. The current study aims at evaluating a polyacetylenic glucoside purified from an edible herb, Bidens pilosa, to present its anti-angiogenic effects. We innovatively find this polyacetylenic glucoside, cytopiloyne, shows anti-angiogenic effect on different in vitro assays and various in vivo animal models under hypoxia. Based on results of this study, cytopiloyne will be a prospective herb angiogenesis inhibitor candidate to control animal or human cancer formation as adjuvant therapy. Abstract: Anti-angiogenesis is a pivotal combination treatment approach in cancer therapy but rare using on companion animals. This study aimed at evaluating the anti-angiogenic effect of a B. pilosa sourced polyacetylenic glucoside, cytopiloyne, on various in vitro assays and in vivo models. We provide evidences showing that CP has anti-angiogenic activities. Firstly, CP inhibited sponge/ Matrigel plug angiogenesis from tumor cells and decreased the survival of tumor cells on hypoxic conditions. Besides, CP declined PKCα protein expression which a protein leads to the growth and spread of tumors under hypoxia. Secondly, inhibitory effects of CP on endothelial angiogenesis were confirmed by chick chorioallantoic membrane assay, tube formation of SVEC4-10 cells and Matrigel plug assay. A dose-dependent CP treatment inhibited 4T1 cells proliferation under hypoxia and migration. It also suppresses VEGF transcription under hypoxia. Finally, we found that CP decreased PDIA4, a novel regulator of cancer growth, expression in endothelial cells. This effect was confirmed by PDIA4 knockout mice with reduced angiogenesis in Matrigel plug assay. Taken together, these results suggest that CP might act as a promising anti-angiogenic herbal agent candidate to be used in animal hypervascularized cancer of veterinary medicine or in combination to control human cancer as adjuvant therapy.

Background: Auriculotherapy is a widely used approach for alleviating discomfort in patients experiencing pain, itchiness, sleep disturbances, and heightened anxiety. This method is also applicable to patients dealing with significant burn scars, who often encounter similar symptoms. Employed as an adjuvant therapy, auriculotherapy demonstrates potential in mitigating these clinical manifestations among individuals with major burn scars. These symptoms are known to be influenced by the autonomic nervous system. Objectives: Despite the absence of current data elucidating the impact of auriculotherapy on the autonomic nervous system, we embarked on an analysis of our heart rate variability (HRV) data to evaluate autonomic system functionality before and after the administration of auriculotherapy. Methods: Paired-samples t-tests and linear regression analysis of HRV variables and correlations with TBSA before and after auriculotherapy of a cohort of 31 survivors from 2016 Formosa Color Dust Explosion was carried out. Results: Significant change of specific HRV variables were found before and after auriculotherapy, and significantly negative correlations was revealed between TBSA and pre-SD prior to auriculotherapy. Conclusion: Our study showed that auriculotherapy may, at least in part, restore the equilibrium of autonomic nervous system and improve HRV parameters.

Visual-inertial integrated navigation system (VINS) has been extensively studied over the past decades to provide accurate and low-cost positioning solutions for autonomous systems. Satisfactory performance can be obtained in an ideal scenario with sufficient and static environment features. However, there are usually numerous dynamic objects in deep urban areas, and these moving objects can severely distort the feature tracking process which is fatal to the feature-based VINS. The well-known method mitigates the effects of dynamic objects is to detect the vehicles using deep neural networks and remove the features belongs to the surrounding vehicle. However, excessive exclusion of features can severely distort the geometry of feature distribution, leading to limited visual measurements. Instead of directly eliminating the features from dynamic objects, this paper proposes to adopt the visual measurement model based on the quality of feature tracking to improve the performance of VINS. Firstly, a self-tuning covariance estimation approach is proposed to model the uncertainty of each feature measurements by integrating two parts: 1) the geometry of feature distribution (GFD), 2) the quality of feature tracking. Secondly, an adaptive M-estimator is proposed to correct the measurement residual model to further mitigate the impacts of outlier measurements, such as the dynamic features. Different from the conventional M-estimator, the proposed method effectively alleviates the reliance of excessive parameterization of M-estimator. Experiments are conducted in a typical urban area of Hong Kong with numerous dynamic objects, and the results show that the proposed method could effectively mitigate the effects of dynamic objects and improved accuracy of VINS is obtained when compared with the conventional method.

Caring for dolphins is a delicate process that requires experienced caretakers to pay close attention to their behavioral characteristics. However, caretakers may sometimes lack experience or not be able to give their full attention, which can lead to misjudgment or oversight. To address these issues, a dolphin behavior analysis system has been designed to assist caretakers in making accurate assessments. The study utilized image preprocessing techniques to reduce sunlight reflection in the pool and enhance the outline of dolphins, making it easier to analyze their movements. The dolphins were divided into 11 keypoints using an open-source tool called DeepLabCut, which helped accurately mark various body parts for skeletal detection. The AquaAI Dolphin Decoder (ADD) was then used to analyze six dolphin behaviors. To improve behavior recognition accuracy, the Long Short-Term Memory (LSTM) neural network was introduced. The ADD and LSTM models were integrated to form the ADD-LSTM system. Several classification models, including unidirectional and bidirectional LSTM, GRU, and SVM, were compared. The results showed that the ADD module combined with a double-layer bidirectional LSTM method achieved high accuracy in dolphin behavior analysis. The accuracy rates for each behavior were over 90%.

Copper-based nanoparticles were synthesized using the glycine–nitrate process (GNP) by using copper nitrate trihydrate [Cu(NO₃)₂‧3H₂O] as the main starting material and glycine [C₂H₅NO₂] as the complexing and incendiary agent. The as-prepared powders were characterized through X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET) analysis, X-ray photoelectron spectroscopy, and scanning electron microscopy. Using Cu(NO₃)₂.3H₂O as the oxidizer (N) and glycine as fuel (G), we obtained CuO, mixed-valence copper oxides (CuO + Cu₂O, G/N = 0.3–0.5), and metallic Cu (G/N = 0.7). The XRD and BET results indicated that increasing the glycine concentration (G/N = 0.7) and reducing particle surface area increased the yield of metallic Cu. The effects of varying reaction parameters such as catalyst activity, catalyst dose, and H₂O₂ concentration on nonylphenol-9-polyethoxylate (NP9EO) degradation were assessed. With a copper‐based catalyst in a heterogeneous system, the NP9EO and total organic carbon removal efficiencies were 83.1% and 70.6%, respectively, under optimum operating conditions (pH, 6.0; catalyst dose, 0.3 g/L; H₂O₂ concentration, 0.05 mM). The results suggested that removal efficiency increased with an increase in H₂O₂ concentration but decreased when the H₂O₂ concentration exceeded 0.0.5 mM. Furthermore, the trend of photocatalytic activity was as follows: G/N = 0.5 > G/N = 0.7 > G/N = 0.3. The G/N = 0.5 catalysts showed the highest photocatalytic activity and resulted in 94.6% NP9EO degradation in 600 min.

With the prevalence of smartphones, the scope of mobile applications has been significantly broadened in the past few years including almost every aspect of our daily life. Among the applications, message dissemination services play a significant role. Traditionally, users send messages to the servers, which forward them according to friend lists. This client-server architecture is efficient with the support of infrastructures, however, it restricts the application scope and may hinder the wide deployment of location-based mobile applications. This paper proposes a novel communication model called passive broadcast for local message dissemination. In this new model, each node does not maintain a connection state and data delivery is initialized by a receiver via a ’scan’ operation. The representative carriers of passive broadcast include Bluetooth and WiFi-Direct, both of which define a mandatory ‘peer discovery’ function. Passive broadcast features negligible cost for establishing and maintaining direct links and is extremely suitable for short message dissemination in proximity. Furthermore, we study the operation management in the proposed communication model with complete protocols and in-depth analysis for optimization. We prototyped our solution on commercial phones and evaluated it with extensive experiments and simulation.

In the last decades, we have witnessed a spectacular information explosion over the Internet. Millions of users are consuming the Internet through various services, such as mobile applications, and online games. The service providers, at the back-end side, are supported by state-of-art infrastructures. Targeting on providing the services at scale, virtualization is one of the emerging technologies used in data centers and cloud environments to improve the quality of services. In this project, we aim to develop a dynamic resource management scheme based on virtual containers. It collects the runtime job progress from the running tasks and allocates the resources dynamically to improve the overall system performance.

Smartphone has become one of the most revolutionary devices in the history of computing. With various kinds of applications, the scope of smartphone has been significantly broadened in the past few years including almost every aspect in our daily life. However, due to the limited on-board resources such as CPU, storage, network bandwidth and battery power, smartphones and the mobile network serving them bring new challenges that have not been encountered in the traditional computing and networking environments. This dissertation focuses on the research areas of improving the network architecture and enhancing the current applications on smartphones. It mainly investigates the areas in the following two directions for three representative categories of mobile services. - In the first direction, the dissertation aims to develop new communication models for smartphone Ad-Hoc networks to achieve efficient communication in the proximity. It is motivated by the fact that smartphone Ad-Hoc networks can help improve the current location-based services and propel new applications. Moreover, the new communication models provide complementary alternatives to the traditional infrastructure-based wireless networks. - In the second direction, the dissertation focuses on improving the other two categories of services, cloud storage services and real-time video streaming services for mobile devices. In the field of cloud storage, we introduce a cloud-assisted approach to provide a set of advanced file operations, such as encryption, decryption and compression, on smartphones. Furthermore, by utilizing the on-board Near Field Communication(NFC) module, we develop an algorithm to securely share the files between mobile devices. For the services of real-time video streaming, we propose approaches that identify a user’s status by analyzing the accelerometer data and then, dynamically adjust the buffer mechanism to save network bandwidth on smartphones.

This study evaluated the mechanical strengths of three types of orthodontic micro-implants by analyzing their structural configurations. Thirty micro-implants of three types (diameter 1.5 mm, Types A, B, C) were assessed. All micro-implants were manually driven into artificial bones at an 8-mm depth. The insertion torque (IT), pullout strength (PS), and gripping volume (GV) of each type were measured. Intergroup comparisons and intragroup correlation were investigated by statistical analysis. Type B had the greatest inner–outer diameter ratio (0.67), and Type A had the smallest (0.53). The IT of Type A (5.26 Ncm) was significantly (p = 0.038) lower than that of Type C (8.8 Ncm). There was no significant difference in the pullout strength (p = 0.868). The GV of Type A (9.7 mm3) was significant (p < 0.01) greater than Type C (8.4 mm3). Type C was significant (p < 0.01) greater than Type B (7.2 mm3). Spearman’s rho rank correlation test showed that PS of Type B was correlated significantly with GV. In conclusion, the design of thread and its GV were the important factors on the mechanical strengths of micro-implant.

Artificial intelligence (AI) is revolutionizing the textile industry by improving the prediction of fabric properties and handfeel, which are essential for assessing textile quality and performance. However, the practical application and translation of AI-predicted results into real-world textile production remain unclear, posing challenges for widespread adoption. This paper systematically reviews AI-driven techniques for predicting these characteristics by focusing on model mechanisms, dataset diversity, and prediction accuracy. Among 811 papers initially identified, 26 were selected for in-depth analysis through both bibliometric and content analysis. The review categorizes and evaluates various AI approaches, including machine learning, deep learning, and hybrid models, across different types of fabric. Despite significant advances, challenges remain, such as ensuring model generalization and managing complex fabric behavior. Future research should focus on developing more robust models, integrating sustainability, and refining feature extraction techniques. This review highlights the critical gaps in the literature and provides practical insights to enhance AI-driven prediction of fabric properties, thus guiding future textile innovations.

Construction productivity entails a wide range of work combinations. When human resources are scarce, it is critical to replace manpower with machinery, and calculating machinery productivity is crucial. Traditional labor productivity methods, however, cannot address dredging complex multi-attribute decision-making (MADM) problems. Aiming to address the limitations of the traditional labor productivity method, this paper extends the data envelopment analysis (DEA) and proposes a new dredging productivity evaluation method. The proposed method can solve the problem of evaluating various combinations of factors (single-input, multiple-input, sin-gle-output, and multiple-output) and the problem suggesting that the efficiency of the DEA method'scalculation results is equal to 1. The effectiveness of the proposed method was verified using reservoir dredging examples. The simulation results show that the proposed method has broad applicability, can accurately evaluate the related dredging performance issues, and provide directions for construction managers to improve labor productivity.

Cholangiocarcinoma is the most common primary malignant tumor of the bile duct. The current standard first-line treatment for advanced or metastatic cholangiocarcinoma is gemcitabine and cisplatin. However, few effective treatment choices exist for refractory cholangiocarcinoma, and additional therapeutic drugs are urgently required. Our previous work demonstrated that the ALDH isoform 1A3 plays a vital role in the malignant behavior of cholangiocarcinoma and may serve as a new therapeutic target. In this study, we found a positive correlation between ALDH1A3 protein expression levels and cell migration abilities of three cholangiocarcinoma cell lines, which was verified using ALDH1A3-overexpressing and ALDH1A3-knockdown clones. We also used ALDH1A3-high and ALDH1A3-low populations of cholangiocarcinoma cell lines from the Library of Integrated Network-based Cellular Signatures (LINCS) program and assessed the effects of ruxolitinib, a commercially available JAK2 inhibitor. Ruxolitinib had a higher cytotoxic effect when combined with gemcitabine. Furthermore, the nuclear translocation STAT1 and STAT3 heterodimers were markedly diminished by ruxolitinib treatment, possibly resulting in decreased ALDH1A3 activation. Notably, ruxolitinib alone or combined with gemcitabine led to significantly reduced tumor size and weight. Collectively, our studies suggest that ruxolitinib might suppress the ALDH1A3 activation through the JAK2/STAT1/3 pathway in cholangiocarcinoma, and trials should be undertaken to evaluate its efficacy in clinical therapy.

Age-related sarcopenia meaningfully increases the risks of functional limitations and mortality in the elderly. Although circulating microRNAs (c-miRNAs) are associated with aging-related cellular senescence and inflammation, the relationships between c-miRNAs and sarcopenia in the elderly remain unclear. This study investigates whether circulating myo-miRNAs and inflammation-related miRNAs are associated with sarcopenia in the elderly. This study recruited 77 eligible subjects (41 males and 36 females) from 597 community-dwelling older adults, and then divided into normal (n=24), dynapenic (loss of muscular function without mass, n=35), and sarcopenic groups (loss of muscular function with mass, n=18). Moreover, myo-miRNAs (c-miRNA-133a and c-miRNA-486), inflammation-related miRNAs (c-miRNA-21 and c-miRNA-146a), and inflammatory-related cytokine levels in plasma were determined using quantitative polymerase chain reaction and ELISA, respectively. The results demonstrated that sarcopenic group exhibited lesser skeletal muscle mass index (SMI), handgrip strength, and gait speed, as well as, lower c-miR-486 and c-miR-146a levels, compared to those of normal and dynapenic groups. Moreover, c-miR-486 level was positively related to SMI (r=0.334, P=0.003), whereas c-miR-146a level was positively associated with SMI (r=0.240, P=0.035) and handgrip strength (r=0.253, P=0.027). In the receiver operating characteristic analysis for predicting sarcopenia, the area under the curve in c-miR-486 was 0.708 (95% confidence interval: 0.561-0.855, P=0.008) and c-miR-146a was 0.676 (95% CI: 0.551-0.801, P=0.024). However, no significant relationships were observed between SMI/ handgrip strength/gait speed and plasma myeloperoxidase/interleukin-1?/interleukin-6 levels. In conclusion, myo-miRNA (c-miR-486) and inflammation-related miRNA (c-miR-146a) are superior to inflammatory peroxide/cytokines in plasma for serving as critical biomarkers of age-related sarcopenia.

This study aims to determine the protective effects of red seaweed Eucheuma cottonii (EC) ethanol extract on acute colitis disease in mice. Male BALB/c mice used for acute colitis disease model by induced 2.5% (w/v) of dextran sulfate sodium (DSS) for 7 days for all groups, except control group. The DSS-induced mice then treated by three different doses of EC extracts (0.35, 0.70, 1.75 g/kg body weight), curcumin (as a positive control, 0.10 g/kg), and a group was orally only by water. In 8^th day, the mice sacrificed and collected the blood, then measured the body weight, colon weight, and colon length. Disease activity index (DAI), pro-inflammatory such as tumor necrosis factor (TNF)-α, interleukin (IL)-1β, and IL-6, as well as IL-10 as anti-inflammatory were measured. The results showed that after treatment for 7 days, EC extract protected the weight loss and decreased the colon weight per length ratio. In addition, EC extract also decreased the pro-inflammatory cytokines expression in serum and increased the IL-10. Moreover, EC extract protected the colonic tissue damage. According to this results, the EC ethanol extract might be can used for the treatment of colitis disease.

3D-mapping-aided (3DMA) global navigation satellite system (GNSS) positioning that improves positioning performance in dense urban areas has been under development in the recent years, but it still faces many challenges. This paper details a new algorithm that explores the potential of using building boundary for positioning. Rather than applying complex simulations to analyze and correct signal reflections by buildings, the approach utilizes a convolutional neural network to differentiate between the sky and building in a sky-pointing fisheye image. A new skymask matching algorithm is then proposed to match the segmented fisheye images with skymasks generated from a 3D building model. Each matched skymask holds a latitude and longitude coordinate to determine the precise location of the fisheye image. The results are then compared with the conventional GNSS and advanced 3DMA GNSS positioning methods. The aims of the proposed algorithm are to increase positioning and heading accuracy in a rich urban environment.

Identifying locations of landslide slip surfaces provides critical information for understanding the volume of landslides and the scale of disasters, which is essential for formulating disaster preparedness and mitigation strategies. Based on hydrogeological survey data from 24 deep-seated landslide-prone sites in Taiwan's mountainous regions, this study first developed the hydraulic conductivity potential index (HCPI) using principal component analysis to quantify hydraulic properties of disturbed rock formation with six geological factors. Then, The regression analysis was performed to construct a permeability estimation model for the geological environment of landslides. Finally, the established model was utilized to develop an identification method for potential slip depths in landslide-prone sites. Results indicated a strong relation between HCPI and hydraulic conductivity with a determination coefficient of 0.895. The relation equation confirmed that its generated data concerning the depths of significant changes in hydraulic conductivity could be used to identify potential slip surfaces. Additionally, this study successfully establishes a rule for identifying potential slip zones by summarizing data concerning the generated hydraulic conductivity profiles, stratigraphic lithology, existing inclinometer slip depth records, and groundwater level of landslide sites. This identification method was then applied to predict potential slip depths for ten landslide sites where slip surfaces have not yet occurred. These findings offer a new alternative to having early information on potential sliding depths for timely disaster management and control implementation.

Hepatocellular carcinoma (HCC) is the most common type of primary liver cancer and is highly invasive and easily recurs. For HCC, chemotherapy shows a limited effect. The gold standard for HCC treatment includes curative surgical resection or liver transplantation. However, the recur-rence rate at 5 years after liver resection is estimated at approximately 70% and even at 5 years after liver transplantation, it is 20%. Therefore, improving survival outcomes after curative surgi-cal resection of liver cancer is crucial. This review highlights the importance of identifying risk factors for HCC recurrence following radical surgical resection and adjuvant therapy options that may reduce the recurrence risk and improve overall survival, including local adjuvant therapy (e.g., transcatheter arterial chemoembolization and radiotherapy), adjuvant systemic therapy (e.g., small molecule targeted therapy and immunotherapy), and other adjuvant therapies (e.g., chem-otherapy). However, further research is needed to refine the use of these therapies and optimize their effectiveness in preventing HCC recurrence.

(1) Background: ganoderic acids (GAs) are specific triterpenes of Ganoderma lucidum. The HPLC fingerprint profile of GAs of the fruiting body has been well-known, but the mycelial fingerprinting remains unclear. (2) Methods: the ethanol extract of the mycelium of G. lucidum (YK-01) was further purified by preparative HPLC. The HPLC spectra for four strains of G. lucidum and one strain of G. formosanum (purple lingzhi) were investigated. (3) Results: nineteen lanostane triterpenes, including five new triterpenes, GA-TP (1), ganodermic acid Jc (GmA-Jc) (2), GmA-Jd (3), GA-TQ1 (4), and ganoderal B1 (5), and fourteen known triterpenes 6-19 were isolated from the ethanol extract. A green chemical HPLC analytical method was developed by using ethanol and acetic acid as mobile phase. These triterpenes comprise of a unique HPLC triterpenoid spectral pattern of G. lucidum mycelium. All four G. lucidum strains showed the same HPLC spectral pattern, whereas G. formosanum displayed a different pattern. Quantitation methods for ganoderic acid T (10) and S (12) were also validated. (4) Conclusions: the triterpenoid HPLC analytical method can be used to identify G. lucidum species, and to determine the contents of GA-T and GA-S.