In the context of high-temperature water vapor treatment, Zn-Mg-Al alloy-coated steel sheets exhibit the emergence of a black surface. This study aims to explore the factors and mechanisms contributing to surface blackening by inducing black surfaces on Zn-Mg-Al alloy-coated steel sheets, which were fabricated through molten coating subjected to water vapor treatment at 150 degrees Celsius. The surfaced composition was predominantly identified as ZnO, a zinc oxide film, validated through X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). Morphological analysis of the surface and cross-section post-water vapor treatment revealed a disrupted lamellar structure with diffused features, resulting in the formation of an oxide film. Optical properties analysis demonstrated an increased absorbance and a decreased bandgap energy after water vapor treatment, indicative of an augmented blackening effect. Consequently, the high-temperature water vapor treatment led to the formation of oxides on the surface, with the highly reactive Mg and Al extracting oxygen from the predominantly present ZnO surface. This process resulted in the creation of an oxygen-deficient oxide, ultimately causing surface blackening.

The post-weld heat treatment (PWHT) cracking susceptibility of a coarse grain heat-affected zone (CGHAZ) in SA213-T23 (2.25Cr-1.6W steel), used for boiler tubes employed in thermal power plants, was investigated using a Gleeble thermal cycle simulator. The PWHT cracking susceptibility test was performed at 650℃, 700℃ and 750℃, and it can be judged that the lower the reduce of area, the more susceptible it is to PWHT cracking. The results of the test also showed higher cracking susceptibility at 650℃ and 700℃, mostly involving intergranular fracture, while at 750℃, transgranular fracture was exhibited. Therefore, the PWHT cracking susceptibility is considered to be closely related to grain boundary. The microstructure of the simulated CGHAZ and PWHT at 650℃, 700℃and 750℃ was observed after etching with nital and alkaline sodium picrate etchants. Alkaline sodium picrate etched microstructures showed a white band at the grain boundary at 650℃, 700℃ and 750, that did not appear in nital etching. Analysis of the white band using EPMA, TEM and nanoindentation revealed that it was intergranular ferrite depleted with C, W and Cr as compared to that in the matrix. Based on these results, we investigated the mechanism of intergranular ferrite formation during PWHT and its effect on PWHT cracking susceptibility at 650℃, 700℃ and 750℃.

Little is known about the effect of statin use in lung cancer development in idiopathic pulmonary fibrosis (IPF). We analyzed the database of the National Health Insurance Service to further investigate the clinical impacts of statin on lung cancer development and overall survival (OS) in IPF patients. The analysis included 9,182 individuals diagnosed with IPF, of which 3,372 (36.7%) were statin users. Compared to statin non-users, the time from diagnosis of IPF to lung cancer development and OS were longer in statin users in IPF patients. In Cox proportional hazard regression models, higher statin compliance, statin use, and being female had an inverse association with lung cancer risk, while older age at diagnosis of IPF and smoking history were associated with higher risk of lung cancer in IPF patients. For OS, statin use, female sex, higher exercise frequency, and diabetes were associated with longer survival. In contrast, older age at diagnosis of IPF and smoking history were associated with shorter OS in IPF patients. These data from a large population indicate that statin had an independent protective association with lung cancer development and mortality in IPF patients.

.Purpose: This paper presents a comparative analysis of state-of-the-art DIR algorithms in the context of head and neck squamous cell carcinoma (HNSCC) radiation therapy. Materials and Methods: We used a dataset of head and neck cancer patients within the Cancer Image Archive, which includes 31 patients with 3D CT image data from pre-treatment, mid-treatment, and post-treatment stages of radiotherapy. We applied DIR algorithms to two datasets, one for pre-treatment to mid-treatment registration and another for mid-treatment to post-treatment registration, by aligning one CT image to another CT image. To quantitatively analyze the patient data, we focused on the spinal cord, optic nerve, brain stem, cochlea, and PTV as the OAR datasets. To verify the DIR algorithm, we used two non-learning-based methods, SyN and NiftyReg, as well as three deep learning-based methods, Voxelmorph, Cyclemorph, and Transmorph. We trained a deep learning model by adjusting the ratio of the training dataset, validation dataset, and test dataset to 7:1:2. Results: The average DSCs of SyN and NiftyReg, the non-learning-based methods, were 0.74±0.06 and 0.70±0.12, respectively. The deep learning-based methods, Voxelmorph, Cyclemorph, and Transmorph, had average DSCs of 0.72±0.08, 0.68±0.11, and 0.69±0.13, respectively. The deep learning DIR algorithm produced transformed outputs of OAR/PTV in a shorter time than other models, including commercial and conventional mathematical algorithms (At Inference(sec/images), Voxelmorph: 0.36, Cyclemorph: 0.3, Transmorph: 5.1, SyN: 140, NiftyReg: 40.2). Conclusions: In conclusion, our study provides a comprehensive comparison of commercial DIR algorithms with traditional and deep learning-based DIR methods. Our results demonstrate that commercial DIR algorithms outperform traditional DIR methods in terms of accuracy and efficiency. However, we also show that deep learning-based DIR methods have the potential to achieve similar performance to commercial algorithms with proper training and optimization. Our findings suggest that both commercial and deep learning-based DIR methods have their respective advantages and limitations, and the choice of method should depend on the specific requirements of the clinical application. Overall, our study contributes to ongoing efforts to improve the accuracy and efficiency of DIR methods for better patient outcomes.

The purpose of this study is to compare and analyze the kinematic characteristics of the upper limb segments during the archery shooting of Paralympic Wheelchair Class archers (ARW2 - second wheelchair class – paraplegia or comparable disability) and Paralympic Standing Class archers (ARST - standing archery class – loss of 25 points in the upper limbs or lower limbs), where archers are classified according to their disability grade among elite disabled archers. The participants of this study were selected as seven elite athletes with disabilities, 4 ARW2, and 3 ARST. The analysis variables were 1) the time required for each phase, 2) the angle of inclination of the body center, 3) the change of trajectory of body center, and 4) the change of movement locus of bow center by phase when performing six shots in total. The ARW2 group showed a longer time than the ARST group, and the angle of the body did not show a significant difference between the two groups. Although there was no significant difference in the mean score between the two groups, it was judged that kinematic performance according to each group was, in that there was a measurable variation in kinematic variables.

The purpose of this paper is to find the time optimal control to a target set for semilinear stochastic functional differential equations involving time delays or memories under general conditions on a target set and nonlinear terms even though the equations contain unbounded principal operators. Our research approach is construct a fundamental solution for corresponding linear systems and establish variations of constant formula of solutions for given stochastic equations. The existence result of time optimal controls for one point target set governed by the given semilinear stochastic equation is also established.

Yttrium oxide (Y2O3) resistive random-access memory (RRAM) devices were fabricated using the sol–gel process on indium tin oxide/glass substrates. These devices exhibited conventional bipolar RRAM characteristics, without requiring a high voltage forming process. The effect of current compliance on the Y2O3 RRAM devices was investigated and revealed that as the set current compliance values increased, the resistance values gradually decreased. Consequently, intermediate resistance values were obtained, which are suitable for multi-level cell (MLC) switching. The fabricated Y2O3 RRAM devices were capable of functioning as an MLC with a capacity of 2 bits in one cell, utilizing three low resistance states and one common high resistance state. The potential of the Y2O3 RRAM for neural networks was further explored through numerical simulations. Hardware neural networks based on the Y2O3 RRAM demonstrated effective digit image classification with a high accuracy rate of approximately 88%, comparable to the ideal software-based classification (~92%). This suggests that the proposed RRAM has the potential to be utilized as a memory component in practical neuromorphic systems.

Prostaglandin E2 (PGE2) is an important biological mediator involved in the defense against Mycobacterium tuberculosis (Mtb) infection. Currently, there are no reports on the mycobacterial components that regulate PGE2 production. Previously, we have reported that RpfE-treated dendritic cells (DCs) effectively expanded the Th1 and Th17 cell responses simultaneously; however, the mechanism underlying Th1 and Th17 cell differentiation is unclear. Here, we show that PGE2 produced by RpfE-activated DCs via the MAPK and cyclooxygenase 2 signaling pathways induces Th1 and Th17 cell responses mainly via the EP4 receptor. Furthermore, mice administered intranasally with PGE2 displayed RpfE-induced antigen-specific Th1 and Th17 responses with a significant reduction in bacterial load in the lungs. Furthermore, the addition of optimal PGE2 amount to IL-2-IL-6-IL-23p19-IL-1β was essential for promoting differentiation into Th1/Th17 cells with strong bactericidal activity. These results suggest that RpfE-matured DCs produce PGE2 that induces Th1 and Th17 cell differentiation with potent anti-mycobacterial activity.

Static and dynamic analysis of website security risks is generally used for website security meas-urements. The website security measurements method recently proposed includes similarity hash-based website security risk analysis and machine learning-based website security risk anal-ysis. In this study, a method that can be performed through information disclosed on the Internet was proposed to measure the risk of a website. DNS information, IP information, and website history information are required to measure the risk of a website. In addition, global traffic rank-ing, malicious code distribution history, and HTTP access status can be checked in the website history information. In this study, information related to the security risk of websites in a total of 2,000 domains was collected and analyzed in 1,000 normal and malicious domains. Through the experiment results, 11 open information collection items were selected to measure the security risk of the website. This study presented the possibility of using public information collection to measure website security risk.

We propose an electrocardiogram (ECG) signal-based algorithm to estimate the respiratory rate is a significant informative indicator of physiological state of a patient. The consecutive ECG signals reflect the information about the respiration because inhalation and exhalation make transthoracic impedance vary. The proposed algorithm extracts the respiration-related signal by finding out the commonality between the frequency and amplitude features in the ECG pulse train. The respiration rate can be calculated from the principle components after the procedure of the singular spectrum analysis. We achieved 1.7569 breaths per min of root-mean-squared error and 1.7517 of standard deviation with a 32-seconds signal window of the Capnobase dataset, which gives notable improvement compared with the conventional Autoregressive model based estimation methods.

Regardless of country and age, the importance of history education is always being emphasized. Although the importance of history education is being emphasized in Korea, there are many difficulties in getting students to understand history properly through school classes alone, and it is also difficult to attract students to participate in classes. The effectiveness of education using games has been proven 20 years ago, and the demand for game-based education is gradually increasing in the current education world, which is becoming more open. In this paper, based on the effects proven through research on the existing game-based education, the improvement of historical thinking ability, experiential history learning, and the problems of game-based education introduced in the ESN report and the discomfort of teachers who participated in the education were improved. A plan was suggested to select and use games suitable for basic education. In this thesis, we selected a history game with a clear historical and periodic background and without distortion of history, and experimented with teaching using games focusing on historical thinking and empirical history learning. The learning achievement of textbook-based education was compared.

Regardless of country and age, the importance of history education is always being emphasized. Although the importance of history education is being emphasized in Korea, there are many difficulties in getting students to understand history properly through school classes alone, and it is also difficult to attract students to participate in classes. The effectiveness of education using games has been proven 20 years ago, and the demand for game-based education is gradually increasing in the current education world, which is becoming more open. In this paper, based on the effects proven through research on the existing game-based education, the improvement of historical thinking ability, experiential history learning, and the problems of game-based education introduced in the ESN report and the discomfort of teachers who participated in the education were improved. A plan was suggested to select and use games suitable for basic education. In this thesis, we selected a history game with a clear historical and periodic background and without distortion of history, and experimented with teaching using games focusing on historical thinking and empirical history learning. The learning achievement of textbook-based education was compared.

(1) Background: The COVID-19 pandemic has affected healthcare utilization rates on a global scale. This study aimed to analyze whether the COVID-19 pandemic affected the characteristics of first-visit patients with peripheral facial palsy visiting a Korean Medicine hospital and to observe characteristics changes in them. (2) Methods: This study analyzed the electronic medical records of 2,310 first-visit patients with peripheral facial palsy who visited the Facial Palsy Center, Korean Medicine Hospital, Kyung Hee University Medical Center from January 1, 2019 to December 31, 2021 in terms of demographic characteristics, disease phase, residence locations, hospital visit route, and patient care type. (3) Results: There were significant relationships between the presence of the COVID-19 pandemic (i.e., before and during) and the number of patients by disease phase (p=0.043), residence locations (p=0.003), residence locations in Seoul (p=0.003), and patient care types (p=0.003). (4) Conclusions: There were several differences in characteristics of first-visit patients with peripheral facial palsy visiting a Korean Medicine hospital during COVID-19 pandemic in terms of demographic characteristics, disease phase, residence locations, residence locations in Seoul, and patient care types.

The present study was conducted to investigate the effects of rhizome extract of Dioscorea batatas (Dioscoreae Rhizoma, Chinese Yam) and its bioactive compound, allantoin, on myoblast differentiation and mitochondrial biogenesis in skeletal muscle cells. Yams were extracted in water and the extract was analyzed by HPLC. The expression of C2C12 myotubes differentiation and mitochondrial biogenesis regulators were determined by reverse transcriptase (RT)-PCR or Western blot. The glucose levels and total ATP contents were determined by glucose consumption, glucose uptake and ATP assays, respectively. Treatment with yam extract (1 mg/mL) and allantoin (0.2 and 0.5 mM) significantly increased of MyHC expression compared with non-treated myotubes. Yam extract and allantoin significantly increased the expression of mitochondrial biogenesis regulating proteins, PGC1?, Sirt-1, NRF-1, and TFAM, as well as the phosphorylation of AMPK and ACC in C2C12 myotubes. Furthermore, yam extract and allantoin significantly increased the glucose uptake levels and the ATP contents. Finally, HPLC analysis revealed that the yam extract contained 1.53% of allantoin. Yam extract and allantoin, stimulated myoblast differentiation into myotubes and increased energy production through upregulation of mitochondrial biogenesis regulators. These findings indicate that yam extract and allantoin can help to prevent the skeletal muscle dysfunction through stimulation of energy metabolism.

Suitable soil structure and nutrient security are important for plant growth and development, characteristics of soil fractal dimension and distribution of physical and chemical properties and their interactions play an important role in studying the stability of soil structure and water and fertilizer cycles. As a sustainable management model, intercropping has positive benefits for erosion control, spatial optimization of resources, as well as improving system productivity. The effects of four intercropping methods on soil fractal dimension and physicochemical properties were investigated by intercropping Salvia miltiorrhiza with forage and S. miltiorrhiza with forest under typical karst rock desertification habitats in Guizhou. The results showed that soil nutrient content of intercropping was significantly higher than that of monoculture, the organic carbon content of soil grown under forest is higher than other treatments, and there was a non-significant change in soil water content of intercropping compared with monoculture. The soil fine-grained matter of intercropping was significantly higher than that of monoculture, while the soil fractal dimension showed a tendency to become larger with the increase of fine-grained matter. The intercropping planting, due to its component types and spatial and temporal configurations, leads to differences in soil water and fertilizer interactions, which can be combined with other ecological restoration measures to optimize the composite model and jointly promote the restoration and development of ecologically fragile areas.

Our study provides guidelines on how to build long-term customer relationship in the non-contract mechanism context. More specifically, the findings show that special, social, and core benefits influence calculative commitment, and operational and special benefits influence affective commitment. This study also supports that calculative and affective commitment play a crucial role in understanding multi-channel agencies’ loyalty. In sum, this study revealed that calculative and affective commitment can be considered as partial or full mediators in the relationship between RBs (relational benefits) and loyalty. This study not only contributed to the existing SET (social exchange theory) and RBs paradigm but also provided practical implications for food distribution management.

In the context of partial autonomy, where autonomous vehicles and humans share control of the vehicle, bringing out-of-the-loop drivers back into the loop is a significant challenge. While warning signal design guidelines are commonly used to provide alerts, few studies have examined each signal in depth with an emphasis on the autonomous environment. This study aims to fill this gap by investigating visual, auditory, and tactile stimuli and modifying their sub-attributes to explore variations related to age, gender, and other individual backgrounds. A driving simulator was utilized to create a realistic driving environment and measure participants' reaction times in takeover request situations. Analysis of the data revealed correlations between age and reaction times for auditory and tactile signals, with interaction effects observed between age and sub-attribute intensity. Additionally, participants exhibited varying reaction time patterns in response to different sub-attribute intensities. By evaluating individual differences in perception based on modality characteristics, often overlooked in prior research, this study serves as a foundational contribution to future research in the field.

Background/Aims: Conflicting results have been reported regarding the interaction between proton pump inhibitors (PPIs) and clopidogrel. We investigated whether concomitant PPI use influenced the risk of recurrence in patients with stroke and myocardial infarction (MI). Methods: This study used two databases for different designs, the Korean National Health Insurance Service (NHIS) database for a self-controlled case series design, and the national sample cohort of the NHIS database converted to the Observational Medical Outcomes Partnership-Common Data Model version for a cohort study. Results: In the PPI co-prescription group, recurrent hospitalization with stroke occurred in 17.6% of the 8,201 patients with history of stroke, and recurrent MI occurred in 17.1% of the 1,216 patients with history of MI during 1 year. According to the self-controlled case series, the overall relative risk (RR) of recurrent stroke was 2.09 [95% confidence interval (CI); 1.83-2.38], and the RR showed an increasing trend with PPI duration. In the cohort study, there was a higher incidence of recurrent stroke in the PPI co-prescription group [Hazard ratio (HR): 1.34, 95% CI: 1.01-1.76, P=0.04]. The overall RR of recurrent MI was 1.47 (95% CI; 1.02-2.11) in the self-controlled case series; however, there was no statistically significant difference in recurrent MI in the cohort study (HR:1.42, 95% CI:0.79-2.49, P=0.23). The impact of individual PPIs on stroke and MI showed different patterns. Conclusions: PPI co-prescription with clopidogrel was associated with recurrent stroke; however, its association with recurrent MI remains inconclusive. The influence of individual PPIs should be clarified in the future.

Obesity, which is characterized by an excessive accumulation of body fat, is one of the critical factors causing metabolic syndrome. Many studies have been performed to identify appropriate agents to control obesity, but toxicity remains a problem. Herein, we identified that phenylbutyrate (PBA), which has been used to treat urea cycle disorder with very low toxicity for a long time, efficiently inhibited high fat-induced body weight gain in a diet-induced obesity mouse model (DIO model). PBA treatment decreased body fat mass and increased lean composition. Moreover, PBA increased brown adipose tissue (BAT) activity by increasing glucose uptake, thereby improving glucose tolerance and insulin tolerance. Interestingly, PBA could induce the expression of phosphofructokinase (PFKL), a key enzyme in the glycolytic pathway, and knocking down PFKL dramatically repressed the expression level of Ucp1 as well as those of Prdm16, Cidea, Pgc1α, and Pparγ, which are marker genes for BAT activation. These results strongly suggested that PBA could increase energy expenditure by increasing BAT activity via the induction of PFKL. Taken together, PBA could be used as a therapeutic agent for people with obesity to prevent the development of metabolic syndrome.

Previous studies had shown that mRNA, miRNA and lncRNA were associated with cardiovascular diseases. The study was aimed to explore the differential expressions of mRNA, lncRNA and miRNA between coronary artery disease (CAD) and healthy control, and their interaction in CAD. We investigated the differential expression of ceRNA between CAD and healthy control through data collected from Gene Expression Omnibus (GEO) microarrays. Furthermore, we investigated the biological function of these differential expressions of ceRNAs by Gene Ontology (GO), Kyoto Encyclopedia of Genes and Genomes (KEGG) analyses. Protein-protein interaction (PPI) network was created to identify the hub genes. Biosystems and literature search were performed for signaling pathways and their function of the included differential expression ceRNAs. A total of 456 miRNA expression profiles, 16,325 mRNA expression profiles, and 2,869 lncRNA expression profiles were obtained. Eleven Go and KEGG pathways (count ≥9), top 15 of PPI network node connectivity rank, and top 15 of ceRNA network node degree centrality rank were achieved at the statistical significance level (P<0.05). We further identified that several differential expressions of ceRNAs and their signaling pathways were associated with CAD through biosystems and literature search. Based on eleven Go and KEGG pathways, top 15 of PPI network node connectivity rank, and top 15 of ceRNA network node degree centrality rank in CAD population, our findings would contribute to further exploration for the molecular mechanism of CAD.

Speech/music classification that facilitates optimized signal processing from classification results has been extensively adapted as an essential part of various electronics applications, such as multi-rate audio codecs, automatic speech recognition, and multimedia document indexing. In this paper, a new technique to improve the robustness of speech/music classifier for 3GPP enhanced voice service (EVS) using long short-term memory (LSTM) is proposed. For effective speech/music classification, feature vectors implemented with the LSTM are chosen from the features of the EVS. Experiments show that LSTM-based speech/music classification produces better results than conventional EVS under a variety of conditions and types of speech/music data.

To expand the application scope and increase the demand for non-crimp fabrics (NCFs) as a lightweight vehicle material, the delamination and thermal strain in NCF composites must be restricted. Accordingly, to simultaneously improve the interfacial bonding and thermal stability of the NCF composites, in this study the epoxy resin, in which SiO2 nanoparticles was modified by a silane coupling agent, were infused to the stacked NCFs and between the layers of NCFs through the vacuum-assisted resin infusion molding (VARIM) process.

To solve the problem that sampling-based Rapidly-exploring Random Tree (RRT) method is difficult to guarantee optimality. This paper proposed the Post Triangular Processing of Midpoint Interpolation method minimized the planning time and shorter path length of the sampling-based algorithm. The proposed Post Triangular Processing of Midpoint Interpolation method makes a closer to the optimal path and somewhat solves the sharp path problem through the interpolation process. The experiments were conducted to verify the performance of the proposed method. Applying the method proposed in this paper to the RRT algorithm increases the efficiency of optimization compared to the planning time.

The epithelial-mesenchymal transition (EMT) is a major event in idiopathic pulmonary fibrosis pathogenesis. Here, we investigated whether growth arrest-specific protein 6 (Gas6) plays a protective role in lung fibrosis via suppression of the EMT and fibroblast activation. rGas6 ad-ministration inhibited the EMT in isolated mouse ATII cells 14 days post-BLM treatment based on morphologic cellular alterations, changes in mRNA and protein expression profiles of EMT markers, and induction of EMT-activating transcription factors. BLM-induced increases in gene expression of fibroblast activation-related markers and the invasive capacity of primary lung fi-broblasts in primary lung fibroblasts were reversed by rGas6 administration. Furthermore, the hydroxyproline content and collagen accumulation in interstitial areas with damaged alveolar structures in lung tissue were reduced by rGas6 administration. Targeting Gas6/Axl signaling events with specific inhibitors of Axl (BGB324), COX-2 (NS-398), EP1/EP2 receptor (AH-6809), or PGD2 DP2 receptor (BAY-u3405) reversed the inhibitory effects of rGas6 on EMT and fibroblast activation. Finally, we confirmed the antifibrotic effects of Gas6 using Gas6−/− mice. Therefore, Gas6/Axl signaling events play a potential role in inhibition of EMT process and fibroblast acti-vation via COX-2-derived PGE2 and PGD2 production, ultimately preventing the development of pulmonary fibrosis.

We investigated the characteristics of surface wind speeds and temperatures predicted by the local data assimilation and prediction system (LDAPS) operated by the Korean Meteorological Administration. First, we classified automated weather stations (AWSs) into four categories [urban flat (Uf), rural flat (Rf), rural mountainous (Rm), and rural coastal (Rc) terrains] based on the surrounding land cover and topography, and selected 25 AWSs representing each category. Then we calculated the mean bias error of wind speed (WE) and temperature (TE) using AWS observations and LDAPS predictions for the 25 AWSs in each category for a period of 1 year (January–December 2015). We found that LDAPS overestimated wind speed (average WE = 1.26 m s–1) and underestimated temperature (average TE = –0.63°C) at Uf AWSs located on flat terrain in urban areas because it failed to reflect the drag and local heating caused by buildings. At Rf, located on flat terrain in rural areas, LDAPS showed the best performance in predicting surface wind speed and temperature (average WE = 0.42 m s–1, average TE = 0.12°C). In mountainous rural terrain (Rm), WE and TE were strongly correlated with differences between LDAPS and actual altitude. LDAPS underestimated (overestimated) wind speed (temperature) for LDAPS altitudes that were lower than actual altitude, and vice versa. In rural coastal terrain (Rc), LDAPS temperature predictions depended on whether the grid was on land or sea, whereas wind speed did not depend on grid location. LDAPS underestimated temperature at grid points on the sea, with smaller TE obtained for grid points on sea than on land.

To assess the usefulness of an attachable video laryngoscope (AVL) by attaching a camera and monitor to a conventional Macintosh laryngoscope (CML). Normal and tongue edema airway scenarios were simulated using a manikin. Twenty physicians performed tracheal intubations using CML, AVL, Pentax AWS® (AWS), and McGrath MAC® (MAC) in each scenario. Ten physicians with more than 10 cases of clinical experience with tracheal intubation using CML were included in the skilled group. Ten physicians with less than 10 cases of clinical experience with tracheal intubation using CML were included in the unskilled groups. The time required to intubate and the success rate were recorded. The degree of difficulty of use and glottic view assessment scored by participants. All 20 participants successfully completed the study. There was no difference in the success rate and time required for tracheal intubation in the normal airway scenarios. For the skilled group, in the tongue edema airway scenario, the AWS had the highest success rate (100%) followed by AVL (60%), MAC (60%), and CML (20%) (p = 0.001). The time required to intubate with the AWS was significantly shorter than with AVL (10.2 vs 22.3 s; p=0.002) or MAC (10.2 vs 23.7 s; p=0.001). There was no significant (p &gt; 0.05) difference between AVL and MAC. The degree of Difficulty of Use for AVL was significantly lower than that for CML (7.8 vs 2.8; p &lt; 0.001). There was no significant (p &gt; 0.05) difference between AVL and other video laryngoscopes. AVL had a higher rate of successful tracheal intubation than CML in the tongue edema scenario. AVL showed a similar success rate and time of tracheal intubation to the MAC. Therefore, AVL may be a possible alternative video laryngoscope device.

The etiological agent of various viral diseases has been identified, and clinical characteristics and complications of each disease are well known. In general, a viral disease appears as acute systemic inflammatory disease, but after acute infection, some patients remain asymptomatic carriers or suffer chronic viral diseases, suggesting that the phenomena are unavoidable processes for viruses’ coexistence with their hosts as virome in microbiota of human species. Although each viral disease has been described as having different pathophysiology, the host's control systems, including immune systems, against the insults from any viral infections, have the same components in previously healthy hosts. Therefore, considering the characteristics of the life cycle of viruses being dependent on the host cell and the same immune components of the host, it is reasonable assumption that there is a common immune mechanism to respond to the insults from all viral diseases. The authors discuss on the characteristics of virus infection and unresolved issues in viral diseases and propose a rationale of early immune modulators for acute insults from viral diseases based on our clinical experiences and the protein-homeostasis-system hypothesis.

When disposing of waste metal resources in landfills, environmental issues such as soil contamination may arise. Recycling these resources not only recovers valuable metals but also mitigates environmental pollution. Platinum (Pt), a valuable metal used in fuel cells for its high water production activity, will see increased future demand as a fossil fuel alternative. This study analyzes the environmental and resource reduction effects of recycled Pt, considering the growing emphasis on its recycling for stable supply and demand of Pt. The environmental impact and resource consumption of recycled Pt with primary Pt (from natural mines) were compared and analyzed using the Life Cycle Assessment (LCA) technique. Results revealed that resource consumption for primary Pt was 8.25E+01 kg Sb-eq./kg, significantly more than the 5.45E+00 kg Sb-eq./kg for recycled Pt. This represents an environmental reduction effect of approximately 93%. In the case of greenhouse gas emissions, primary Pt emitted 1.35E+04 kg CO2-eq./kg, while recycled Pt emitted 6.94E+02 kg CO2-eq./kg, resulting in an environmental reduction effect of approximately 95%. In conclusion, recycling Pt, compared to primary extraction, offers substantial environmental and resource reduction benefits. This study underscores the significance of recycling and highlights the potential environmental improvements achievable through sustainable practices.

Acute pancreatitis (AP) is a leading gastrointestinal disease that cause hospitalization. Initial management in the first 72 h after the diagnosis of AP is pivotal, which can influence the clinical outcomes of the disease. Initial management, including fluid resuscitation, pain control, nutritional support, antibiotic use, and endoscopic retrograde cholangiopancreatography (ERCP) in gallstone pancreatitis, plays a fundamental role in AP treatment. Recent updates for fluid resuscitation, including treatment goals, the type, rate, volume, and duration, have triggered a paradigm shift from aggressive hydration with normal saline to goal-directed and non-aggressive hydration with lactated Ringer’s solution. Evidence of the clinical benefit of early enteral feeding is becoming definitive. Routine use of prophylactic antibiotics is generally limited, and the procalcitonin based algorithm of antibiotic use has recently been investigated to distinguish between inflammation and infection in patients with AP. Although urgent ERCP (within 24 h) should be performed for patients with gallstone pancreatitis and cholangitis, urgent ERCP is not indicated in patients without cholangitis. Furthermore, convalescent treatment, including cholecystectomy in gallstone pancreatitis and alcohol intervention in alcoholic pancreatitis, is also important for improving the prognosis and prevent recurrence in patients with AP. This review focuses on recent updates on the initial and convalescent management strategies for AP.

The study is to identify motivational factors that lead to collective intelligence and to understand how these factors relate to each other and to innovation capabilities in enterprises. The relationships between each of the sub-factors of the collective intelligence construct with the sub-factor of incremental innovation were examined. The study used the convenience sampling of corporate employees who use collective intelligence from corporate panel members (n=1500). Collective intelligence was found to affect work process, operations, and service innovation. This suggests that as work processes are made more innovative, the more actively collective intelligence is pursued, the greater the improvement in the performance of work processes, work procedures, work efficiency, customer satisfaction, and services. This study provides significant implications for corporations operating collective intelligence services such as online communities. First, such corporations vitalize their services by raising the quality of information and knowledge shared in their communities. Additionally, contribution motivations that take the characteristics of knowledge and information contributors into consideration require further development.The sample for this study was identified through convenience sampling of corporate employees who use collective intelligence from corporate panel members (n=1500). Collective intelligence was found to affect work process, operations, and service innovation. This suggests that as work processes are made more innovative, the more actively collective intelligence is pursued, the greater the improvement in the performance of work processes, work procedures, work efficiency, customer satisfaction, and services. This study provides significant implications for corporations operating collective intelligence services such as online communities. First, such corporations vitalize their services by raising the quality of information and knowledge shared in their communities. Additionally, contribution motivations that take the characteristics of knowledge and information contributors into consideration require further development.

Rottlerin(R) is a natural extract from Mallotus philippensis with antiviral properties. Feline Infectious Peritonitis (FIP) is a fatal disease characterized by systemic granulomatous inflammation and high mortality, with no established prevention or cure. We investigated antiviral effect of liposome loaded R, Rottlerin-liposome(RL) against Feline infectious peritonitis virus (FIPV), the causative agent. We demonstrated that R and RL inhibited FIPV replication in dose dependently with a PKCδ related manner, not only in the early endocytosis step but also in the late step of replication. RL resolved the low solubility issue of rottlerin and improved its inhibition efficacy at the cellular level. Based on these findings, we suggest that RL has a value for further research as a potential antiviral agent against FIPV.

Due to growing concerns about environmental pollution from plastic waste, plastic recycling research is gaining momentum. Traditional methods, such as incorporating inorganic particles, increasing cross-linking density with peroxides, and blending with silicone monomers, often improve mechanical properties but reduce flexibility for specific performance requirements. This study focuses on synthesizing silica nanoparticles with vinyl functional groups and evaluating their mechanical performance when used in recycled plastics. Silica precursors, namely sodium silicate, and vinyltrimethoxysilane (VTMS), combined with a surfactant, were employed to create pores, increasing silica's surface area. Early-stage introduction of vinyl functional groups prevented the typical post-synthesis reduction in surface area. Porous silica was produced in varying quantities of VTMS, and the synthesized porous silica nanomaterials were incorporated into recycled Polyethylene to induce cross-linking. Despite a decrease in surface area with increasing VTMS content, a significant surface area of 883 m2/g was achieved. In conclusion, porous silica with the right amount of vinyl content exhibited improved mechanical performance, including increased tensile strength, compared to conventional porous silica. This study shows that synthesized porous silica with integrated vinyl functional groups effectively enhances the performance of recycled plastics.

Liver cirrhosis is a chronic disease that is characterized by the presence of fibrosis and regeneration of nodules in the liver whose consequences are the development of portal hypertension and liver failure. Cirrhosis arises from a wide variety of chronic diseases, which progresses slowly after years or decades. Liver cirrhosis is a public health problem. It is usually associated with viral hepatitis, consumption of alcohol, metabolic syndrome, autoimmune processes, storage diseases, toxic substances, and medications. Cirrhosis is the fourteenth most common cause of death in adults throughout the world, the fourth in Europe and the ninth in the United States. The prevalence of this disease is underestimated because it is symptomatic it is not diagnosed in initial stages, and it usually goes to the decompensated stage at a rate of 5 to 7% per year. We review here the epidemiology, pathophysiology, etiology, and diagnosis of liver cirrhosis.

This study was designed to assess the reliability of geographic information using satellite image information in ungauged basins. For this, this study constructed geographic information using actual gauged data and satellite information data and conducted runoff analysis through S-RAT, a rainfall–runoff model, and performed the comparison and analysis of geographic information and runoff data. For actual gauged data, the gauged geographic information of the Water Resources Management Information System (WAMIS) was collected, and for satellite information, the image information of moderate-resolution imaging spectroradiometer (MODIS) observation sensor loaded on Terra Satellite was collected. As analysis areas, three basins where mountains occupy more than 80% and another three basins where urban areas occupy more than 7% in the Han River basin were selected. According to the analysis result, the gauged information and satellite image information showed great difference in runoff, maximum 50% in peak flood and maximum 17% in total flood, in the rivers with many urban areas, while the runoff difference in the rivers with many mountains showed maximum 13% in peak flood and 4% in total flood. What showed the greatest difference in image information was land use, and it turned out that the MODIS satellite recognized the urban rivers as cities for more than maximum 60% compared to WAMIS-gauged data. Meanwhile, in the forest area, the MODIS satellite image showed error of less than 5% of the WAMIS-gauged data, which indicates that it has higher applicability in Mountain Rivers.

2.25Cr-1Mo steel with high strength at high temperatures and good hydrogen resistance is widely used for power generation boiler material in high temperature and pressure use environments. Following the test evaluation of the ASME Boiler and Pressure Vessel Code, specimens from the base metal of a boiler pipe were found to have impact toughness values of 285 and 21 ft-lb, which are drastically different values. The analysis of the fracture surface of the 21 ft-lb test specimen revealed MnS inclusions, and it was found that cracks initiated at the inclusions. Observation of the cross-section of the crack propagation front revealed that cracks propagated along the ferrite regions and precipitate voids. Inclusions were also found in the 285 ft-lb impact specimen; however, the volume fraction of the inclusions was significantly less than that of the 21 ft-lb specimen. It was also found that the ferrite and carbide content of the 285 ft-lb specimen was less than 21 ft-lb specimen. The reason that the inclusions, ferrite, and carbide content differed in the two adjacent impact test specimens was analyzed. The effects of micro-segregation, such as MnS inclusions on ferrite and carbide, were compared and analyzed.

Aim: To improve risk stratification in early-stage endometrial cancer (EC), we performed mo-lecular classification, and L1CAM immunohistochemistry (IHC) for additional risk assessment. Method: We analyzed archival tumor tissue from 247 early-stage EC patients. POLE mutations were detected using a Droplet digital polymerase chain reaction assay and Sanger sequencing, while the mismatch repair (MMR) status was determined by MMR protein IHC and MSI test. Additionally, we conducted IHC of p53 and L1CAM. Results: The 247 ECs were categorized into four subgroups: POLE-mutated (13.0%), MMR-deficient (27.9%), p53-abnormal (8.5%), and non-specific molecular profile (NSMP, 50.6%). We further subcategorized NSMP subgroup into NSMP-L1CAMneg (44.9%) and NSMP-L1CAMpos (5.7%), which we refer to as the molecu-lar-L1CAM classification. The molecular-L1CAM classification was an independent prognostic factor for recurrence-free survival (RFS) and overall survival (OS) (p <0.001, each). Similarly, the simplified L1CAM-p53 categorization, for practical use, remained an independent prognostic factor for RFS and OS (p <0.001, p =0.003, respectively). Conclusion: Integrating the molecu-lar-L1CAM classification or the simplified L1CAM/p53 categorization can enhance risk stratifi-cation in early-stage EC, providing valuable prognostic information to guide treatment deci-sions and improve patient outcomes.

The wind observations for multiple levels (40–200 m) have been conducted for a long time (2016–2020) on Jeju Island of South Korea. This study aims at understanding the vertical and temporal characteristics of lower atmosphere. Jeju Island is a region located at mid-latitude and is affected by seasonal monsoon wind. The maximum wind speed appears in the lower layer during day time and is delayed in the upper layer during latter time in diurnal cycle. In summer season, the surface layer increases up to 160 m during day time via dominant solar radiation effect, which is higher than those for other seasons. However, the maximum wind speed in winter season appears irregularly among altitudes, and the surface layer is ~100 m, which is lower than that in summer season. It can be attributed to the increase in the mean wind speed in diurnal cycle caused by the strong northwestern wind for winter season. These results imply that the relationship between near-surface and higher altitudes is primarily affected by solar radiation and seasonal monsoon winds. These results are expected to contribute to site selection criteria for wind farms and to the assessment concerning planetary boundary layer modeling.

Sphingolipids are ubiquitous in eukaryotes and certain prokaryotes, where they serve as vital components of biological membranes and as bioactive molecules. Chloroplasts have complex membrane structures that play crucial roles in photosynthesis, but their specific sphingolipidome remains unreported. In this study, we used high-performance liquid chromatography-mass spectrometry (HPLC-MS/MS) to analyze the sphingolipidome of purified Arabidopsis thaliana chloroplasts. We detected 92 chloroplast sphingolipids. The chloroplast sphingolipidome differed from total leaf (TL) samples, having a higher content of free long-chain bases and hydroxyceramides, and a greater proportion of complex sphingolipids with 16C fatty acid (FA) forms. Notably, chloroplast glucosylceramides were predominantly the d18:1 h16:0 and t18:1 h16:0 forms, rather than the 24C FA form found in TL and other cellular structures. Comparing the sphingolipidomes of different cellular structures underscores the inhomogeneity of intracellular distribution of sphingolipids. This provides a robust reference for further elucidating the function of sphingolipids in plant cells.

The role of upfront primary tumor resection (PTR) in patients with unresectable metastatic col-orectal cancer (CRC) without severe symptoms remains controversial. We retrospectively ana-lyzed the role of PTR in overall survival (OS) in different subgroups. Among 331 patients diag-nosed with synchronous metastatic CRC between 2010 and 2020, 223 were analyzed. The PTR group (n = 42) showed better performance (p = 0.038); higher frequencies of right-sided origin (p = 0.014), T4 stage (p = 0.005), M1a stage (p = 0.015), and <2 organ metastases (p = 0.002); and re-ceived fewer targeted agents (p < 0.001) than the chemotherapy group (n = 181). The PTR group showed longer OS (20.5 versus 14.0 months, p = 0.016), but PTR was marginally related to OS in multivariate analysis (p = 0.060). Male sex (p = 0.022), good performance status (p = 0.07), left-sided tumor (p = 0.069), low serum carcinoembryonic antigen level (p = 0.092), T3 stage (p = 0.029), M1a stage (p = 0.025), <2 organ metastases (p = 0.017), and administration of targeted agents, especially bevacizumab (p = 0.024), were related to survival benefit after PTR. Upfront PTR should be considered when selecting patients with favorable prognoses for bevacizumab administration.

Directed Energy Deposition (DED) is a process that enables high-speed deposition with a sub-millimeter thickness using laser technology. Thus far, defect studies on additive manufacturing, including DED, have focused mostly on preventing pores and crack defects that reduce fatigue strength. On the other hand, evaporation products, fumes and spatters, generated by the high energy have often been neglected despite being some of the main causes of porosity and defects. In high-quality metal deposition, the problems caused by evaporation products are difficult to solve, but they have not yet caught the attention of metallurgists and physicists. This review examines the effect of the laser, material, and process parameters on the evaporation products to help obtain a high-quality metal film layer in thin-DED.

Antibiotics’ effect on Mycoplasma pneumoniae (MP) infection still remains controversial. A prospective study of 257 children with MP pneumonia during a recent epidemic (2015-2016) was conducted. All MP pneumonia patients were treated with corticosteroids within 24-36 h after admission. Initially, oral prednisolone (1 mg/kg) or intravenous methylprednisolone (IVMP) (1-2 mg/kg) was administered for mild pneumonia patients, and IVMP (5 -10 mg/kg/day) for severe pneumonia patients. If patients showed persistent fever for 36-48 hours or disease progression, additive IVMP (5 mg/kg or 10 mg/kg) was given. Eighty-five patients received only a broad-spectrum antibiotic without macrolide. The mean age and the male:female ratio were 5.6 ± 3.1 years, respectively. Seventy-four percent of patients (190/257) showed immediate defervescence within 24 h, and 95.7% (246/257) of patients showed defervescence within 72 h with improvements in clinical symptoms. Eight patients who received additive IVMP also showed clinical improvement within 48 h without adverse reactions. There were no clinical or laboratory differences between patients treated with a macrolide (n = 172) and without (n = 85). Early corticosteroid therapy might reduce disease morbidity and prevent disease progression in MP pneumonia patients without side effects, and antibiotics may have limited effects on MP infection.

As one of GEO-constellation for environmental monitoring in the next decade, Geostationary Environment Monitoring Spectrometer (GEMS) is designed to observe the Asia Pacific region to provide the information on the atmospheric chemicals, aerosol and cloud properties. For the continuous monitoring of the sensor performance after its launch in early 2020, here we suggest deep convective clouds (DCCs) as a possible target for the vicarious calibration of GEMS, the first UV/VIS hyperspectral sensor onboard a geostationary satellite. Tropospheric Monitoring Instrument (TROPOMI) and Ozone Monitoring Instrument (OMI) are used as a proxy of GEMS, and a conventional DCC detection approach applying the thermal threshold test is used for the DCC detection based on the collocations with Advance Himawari-8 Imager (AHI) onboard Himawari-8 geostationary satellite. DCCs are frequently detected over the GEMS observation area on average over 200 pixels in a single observation scene. Considering the spatial resolution of GEMS, 3.5 km×7 km which is similar to TROPOMI, and its temporal resolution (8 times a day), availability of DCCs for vicarious calibration of GEMS is expected to be sufficient. Inspection of the DCC reflectivity spectra estimated from the OMI and TROPOMI data also shows a promising result. Even though, their observation geometry and sensor characteristics are quite a different, the estimated DCC spectra agree quite a well within a known uncertainty range with comparable spectral features. When the DCC detection is further improved by applying both visible and infrared tests, the variability of DCC reflectivity from the TROPOMI data is reduced by half, from 10% to 5%. This is mainly due to the efficient screening of cold thin cirrus with the visible test and of bright warm clouds with the infrared test. The precise DCC detection is also expected to contribute to the accurate characterization of the cloud reflectivity, which will be further investigated.

Purpose: Intervertebral disc is a leading avascular organ in the body. Hence, it may utilize autophagy and apoptosis to alive in unfavorable condition like stress and mechanical force. But excessive force and stress is a key cause to intervertebral disc degeneration (IVDD). Purpose of this study is to identify, external fixator (EF) and saline injection (SI) may induce autopahgy and apoptosis mediated nucleus pulposus (NP) cells death in rat tail’s disc and which method is better for studying autophagy and apoptosis. Methods: Sixteen 9-week-old male Sprague–Dawley rat tails were treated with 0.9% saline and EF (two-cross kirschner wires) for 6 weeks and 12 weeks as well. Treated discs were dissected for checking out participation of autopahgy and apoptosis to intervertebral disc degradation (IVDD). For identifying them, we performed H&E staining, Masson’s trichrome staining, and Immunohistochemistry (IHC) for LC3, Beclin-1and P62 as well as MMP-2, MMP-3 and TIMP-1.Furthermore, we performed quantitative polymerase chain reaction (qPCR)to check out autophagy related gene expression (beclin-1, LC3 and P62) and apoptosis related gene expression (MMP-2, MMP-3 and TIMP-1) respectively. Results: More insidious nucleus pulposus (NP) cell degeneration was indentified in (EF) group than in (Ctrl) control group. And rate of degradation was elevated with increasing duration of compression, but SI group cannot distinguish the margin of AF and NP cells. Highest along with lateral expression was found for LC3, Beclin-1, and P62 of both groups. Up-regulated and central expression was observed for MMP-2, MMP-3 and TIMP-1 of both groups, although SI group cannot recognize the margin between NP and AF cells. Utmost autophagy related gene expression was identified in EF group than in SI group. Besides, maximum autophagy accumulating materials was found in EF group than in SI group. And it was amplified along with increasing the duration of compression. Highest, apoptotic gene expression was observed in SI group, whereas, EF group showed lowest expression. Conclusion: External fixator (EF) method was better to study autophagy and apoptosis because it enhanced IVDD after compression which is actively linked with autophagy and apoptosis. Degeneration process was conversely proportional along with duration of compression. On contrary, saline injection (SI) could not distinguish AF and NP cell border.

FMD is a highly contagious animal disease that occurs in cloven-hoofed animals including pigs. To prevent FMD, vaccines and adjuvants are used to induce an immune response, but it is not sufficient to show the effect of preventing viral infection. In this study, we conducted to evaluate the increasing effect of FMD vaccine SP antibody by administrating Zn-ASP to 100 pigs from three test pig farms with feed. FMD vaccine antibody titer and immunological index were analyzed using an enzyme-linked immunosorbent assay (ELISA) kit, and hematological and blood biochemical parameters were analyzed using an automatic blood analyzer. The titer of FMD vaccine SP antibody in the 0.2% Zn-ASP-administered group significantly increased compared to that in the positive control group only injected with FMD vaccine at 4 weeks after the first vaccination and at 4, 8 and 16 weeks after the second vaccination, respectively (p&lt;0.05). The FMD vaccine SP antibody positive rate was 100% until shipment. IFN-γ and IgA were significantly increased by Zn-ASP administration 4 weeks after the first vaccination and 4 weeks after the second vaccination (p&lt;0.05). On the other hand, serum AST, and CPK (p&lt;0.001) were significantly decreased by Zn-ASP. Our results show that the administration of Zn-ASP is effective in enhancing the antibody titer and immunity of the FMD vaccine by FMD vaccination, and it is thought that it can be used as an oral adjuvant (OrAd) to prevent viral diseases such as FMD.

Purpose: To evaluate clinical outcomes after bilateral mix-and-match cataract surgery using extended depth of focus (EDOF) and diffractive multifocal (DMF) intraocular lenses (IOLs). Methods: Thirty-seven patients received Tecnis Symfony EDOF IOL (ZXR00) implantation in the dominant eye, and Tecnis +3.25 DMF IOL (ZLB00) in the non-dominant eye. Patients were followed for 3 months, and uncorrected and corrected distance visual acuity (UDVA, CDVA) , uncorrected intermediate and near visual acuity (UIVA, UNVA), contrast sensitivity, defocus curves, stereopsis, and patient satisfaction were assessed. Results: At 3 months, mean logMAR UDVA was 0.07 ± 0.09 in EDOF IOL eyes, 0.12 ± 0.11 in DMF IOL eyes, and 0.02 ± 0.05 in both eyes. UIVA was 0.11 ± 0.11 in EDOF IOL eyes, 0.16 ± 0.12 in DMF IOL eyes, and 0.04 ± 0.07 in both eyes. UNVA was 0.25 ± 0.15 in EDOF IOL eyes, 0.22 ± 0.16 in DMF IOL eyes, and 0.13 ± 0.13 in both eyes. Thirty patients(81.1%) were more than satisfied with near vision, and 8 patients(21.6%) complained of severe glare and halo. Spectacle independence for near vision was achieved in 34 patients(91.9%), and 31 patients(83.8%) had better than a 50 second arc of stereopsis. Conclusion: Mix-and-match cataract surgery with EDOF and DMF IOL implantation provided good visual outcomes through all distances. Also excellent patient satisfaction was achieved with high level of spectacle independence and minimal photic phenomena.

Despite numerous studies on cancer treatment, cancer remains a challenging disease to cure, even after decades of research. In recent years, cancer vaccine has emerged as a promising approach for cancer treatment, offering few unexpected side effects compared to existing therapies. How-ever, cancer vaccine faces obstacles to commercialization due to its low efficacy. Particularly, the Toll-like receptor (TLR) adjuvant system, specifically the TLR 7/8 agonist, has shown potential for activating Th1 immunity, which stimulates both innate and adaptive immune responses through T cells. In this study, we developed ProLNG-S, a cholesterol-conjugated form of resiquimod (R848), to enhance immune efficacy by stimulating the immune system and reducing toxicity. ProLNG-S was formulated as ProLNG-001, a positively charged liposome, and co-administered with oval-bumin (OVA) protein in the B16-OVA model. ProLNG-001 effectively targeted secondary lym-phoid organs, resulting in a robust systemic anti-tumor immune response and tumor-specific T cell activation. Consequently, ProLNG-001 demonstrated potential for preventing tumor progression and improving survival compared to AS01 by enhancing anti-tumor immunity.

This study aims to evaluate the climate-change response of greening persistently vacant houses and barren sites in deteriorated high-density residential areas in old downtown metropolitan areas. The current status of building demolition sites in Ami-dong and Chojang-dong, Busan Metropolitan City, was examined. In this area, of the 340 vacant houses from 2017, 246 (72.35%) remained persistently vacant till 2020. In 2020, 213 barren sites were neglected after building demolition. Amongst these sites, 177 (83.10%) were paved with concrete. Persistently vacant houses and barren sites were afforested, and the climate-change response was quantified in terms of flood reduction and CO2 mitigation in four scenarios (current, concrete, ground cover plants, and trees). Runoff analysis was performed using the Korea low-impact development model (K-LIDM) to assess flood mitigation. The tree scenario showed average runoff mitigations of 1.71%, 2.38%, and 3.06% in the long-term, 30-year, and 2-year rainfall scenarios, respectively. Additionally, 3058 deciduous broadleaf trees may be planted in the study area to promote CO2 mitigation. Thus, an additional annual carbon fixation of 62,123.78 kg CO2 may be expected. The greening of vacant houses and demolished sites was effective in all aspects of the climate-change response, and tree-based greening exhibited the most significant effect.

The effects of chemical composition and solidification rate on the solidification behavior of high-Cr white irons were investigated through directional solidification. Increasing the solidi-fication rate in hypoeutectic alloys caused the finer dendrite arm spacing as expected. The eutec-tic structure which formed in the interdendritic region comprised of M7C3 and austenite, how-ever, secondary dendrite arms of hypoeutectic alloys contained a few M7C3 particles that solidi-fied prior to the eutectic structure. The transition from cellular to dendritic solidification oc-curred at a solidification rate between 50 µm/s and 100 µm/s in a near eutectic alloy. In the near eutectic alloy with cellular solidification, a directionally arrayed in-situ composite of M7C3/austenite formed within the cell. Speckle-like feature appeared in the intercellular region due to M23C6 carbide precipitation during subsequent cooling after freezing. Like dendrite arm spacing in hypoeutectic alloys, the inter-speckle spacing and the inter-fibre spacing became finer with increasing solidification rate in the cellular solidification range.

The aim of this work is to study the phase transformations, microstructures and mechanical properties of the martensitic stainless steel (MSS) 410 deposits produced by laser powder-directed energy deposition (LP-DED) additive manufacturing. The LP-DED MSS 410 deposits underwent the post heat treatment in austenitizing at 980℃ for 3hrs and followed by different tempering treatment at the temperatures of 250, 600, and 750℃ for 5hrs, respectively. The analyses of phase transformations and microstructural evolutions of LP-DED MSS 410 were carried out using X-ray diffraction, SEM-EDS, and EBSD. Vickers hardness and tensile strength properties were also measured to analyze the effects of the different tempering heat treatments. It reveals that as-built MSS 410 has very fine lath martensite and high hardness of about 480HV1.0 and tensile strength of about 1280 MPa, but elongation was very lower than the post heat treated ones. Precipitations of chromium carbide (Cr23C6) were most commonly observed at the grain boundaries and the entire matrix at the tempering temperatures of 600℃ and 750℃. In general, the tensile strengths de-creased from 1381MPa to 688MPa as tempering temperatures increased up to 750℃ from 250℃. Additionally, as the tempering temperature increased, the chromium carbide and tempered mar-tensite structures became coarser.

Rotorcrafts operate HUMS for fault diagnosis, but the capabilities of HUMS analysts are important due to the complex mechanical configuration of rotorcraft and the difficulty of analysis. Accordingly, an advanced algorithm is needed to identify faults, and flight data can be used to develop the algorithm. However, flight data contains abnormal or missing data due to problems such as sensor defects, which can be a major problem in algorithm development. Therefore, in this paper, we study a gap filling method using MLP to obtain normal data when there are problems such as abnormal or missing data in rotorcraft flight data. Existing methods typically fill the gap through interpolation or curve fitting using the before and after values of missing data. However, in this study, normal values were estimated using the values of other parameters at the moment of missing or abnormal data occurred. As a result of evaluating the performance of the trained MLP using normal data, it was confirmed that the output of the model well estimates the changing trend of the target. And when abnormal data was applied to the trained model, it was confirmed that point outliers were eliminated and appropriate values were found in the case of missing data.

Rapeseed (Brassica napus L.) is one of the most oil crop, and its commercial value is contingent upon its agronomic characteristics and oil quality. In this study, 73,226 single nucleotide polymorphisms (SNPs) across 95 rapeseed mutant lines derived from gamma rays and their original cultivar (‘Tamra’) obtained from genotyping-by-sequencing (GBS) was investigated gene ontology (GO) analysis and genome-wide association study (GWAS). GWAS was conducted on agronomic (plant height, ear length, thousand seed weight and seed yield) and oil (fatty acid and crude fat) traits. GO analysis showed that many genes displaying SNPs were involved in cellular processes, intracellular anatomical structures and organic cyclic compound binding. A total of 149 significant SNPs were associated with the agronomic traits (76 SNPs) and oil traits (73 SNPs). Bna.A05p02350D (SFGH) and Bna.C02p22490D (MDN1) were selected as novel candid genes for thousand seed weight. In addition, Bna.C03p14350D (EXO70) and Bna.A09p05630D (PI4Kα1) were selected as novel candidate genes for the erucic acid and crude fat content, respectively. These findings could facilitate the identification of optimal genotypes for breeding new cultivars, and association studies represent an economically efficient tool for mutant screening and the selection of elite rapeseed-breeding lines.

This comprehensive review explores the advancements in Orthognathic and Oral Maxillofacial Surgery, focusing on the integration of 3D Printing and Virtual Surgical Planning (VSP). Traditional surgical methods, while effective, come with inherent risks and complications, and can lead to variability in outcomes due to the reliance on the surgeon's skill and experience. The shift towards patient-centric care necessitates personalized surgical methods, which can be achieved through advanced technology. The amalgamation of 3D printing and VSP revolutionizes surgical planning and implementation by providing tactile 3D models for visualization and planning, and accurately designed surgical guides for execution. This convergence of digital planning and physical modeling facilitates a more predictable, personalized, and precise surgical process. However, the adoption of these technologies presents challenges, including the need for extensive software training and the steep learning curve associated with computer-aided design programs. Despite these challenges, the integration of 3D printing and VSP paves the way for advanced patient care in orthognathic and oral maxillofacial surgery.

Some time ago, Kobayashi et al. experimentally studied the so-called Lee-Naughton-Lebed's (LNL) angular effect in strong electric fields [K. Kobayashi, M. Saito, E. Omichi, and T. Osada, Phys. Rev. Lett. \textbf{96}, 126601 (2006)]. They found that strong electric fields split the LNL conductivity maxima in $\alpha$-(ET)$_2$-based organic conductor and hypothetically introduced the corresponding equation for conductivity. In this Letter, for the first time we suggest quantum mechanical theory of the LNL angular oscillations in moderately strong electric fields. In particular, we demonstrate that the obtained by us approximate theoretical formula coincides with the hypothetical one and well describes the above mentioned experiments.

This study aims to suggest a basis for the selection of technologies for developing high-performance buildings to reduce energy consumptions and greenhouse gas emissions. Energy-saving technologies comprising of 15 cases were categorized into passive, active, and renewable energy systems. EnergyPlus v8.8 was used to analyze the contribution of each technology in reducing the primary energy consumptions and CO₂ emissions in the Korean climate. The primary energy consumptions of the base model were 464.1 and 485.1 kWh/m²a in the Incheon and Jeju, respectively, and the CO₂ emissions were 83.4 and 87.4 kgCO₂/m²a, respectively. Each technology (cases 1–15) provided different energy-saving contributions in the Korean climate depending on their characteristics. The heating, cooling, and other energy-saving contributions of each technology indicate that their saving rates can be used when selecting suitable technologies during the cooling and heating seasons. Case 15 (active chilled beam with dedicated outdoor air system + ground source heat pump) showed the highest energy saving rate. In case 15, the Incheon and Jeju models were reduced by 189.4 (59.2%) and 206.2 kWh/m²a (57.4%) compared to the base case, respectively, and the CO₂ emissions were reduced by up to 32.7 (60.8%) and 35.6 kgCO₂/m²a (59.3%), respectively.

Alginate, a biopolymer promising in food, biomedical, pharmaceutical, and electronic materials industries, is characterized by its biodegradability, biocompatibility, low toxicity, and gel-forming properties. It is most abundantly found in brown algae. However, conventional dilute acid and alkali extraction methods face limitations in commercialization due to their long processing time, low throughput, and high solvent requirements. In this study, a microwave-assisted extraction (MAE) process for sodium alginate was designed to improve extraction efficiency. Solid/liquid ratio, extraction temperature, and extraction solvent concentration were major variables affecting sodium alginate extraction from Undaria pinnatifida(sea mustard). They were then statistically optimized using response surface methodology. Under optimal conditions (13.27 g/L, 91.86 ℃, 2.51 %(w/v), and 15 min), the yield was 38.41 %, which was 93.43 % of the theoretical content of sodium alginate in Undaria pinnatifida. Our work has confirmed the productivity and industrial feasibility of efficient extraction of sodium alginate from marine biomass, and we hope that it will serve as an encouraging case for the application of biopolymers as one of the desirable options for alternative petrochemicals to construct a sustainable society.

Hair loss attributed to excessive stress from work and lifestyle changes has become a growing concern, particularly among young individuals. However, currently used drugs such as minoxidil and finasteride impose a plethora of side effects. Therefore, natural substances as alternatives have garnered research interest. A recent study showed the efficacy of Malva verticillata seed extracts in alleviating hair loss via upregulation of the Wnt/β-catenin signaling pathway. In this study, the efficacy of M. verticillata seed extracts on alleviation of hair loss was further investigated. Further fractionation and purification of the seed extracts using silica gel column chromatography and preparative high-performance liquid chromatography helped identify linoleic acid (LA) and oleic acid as the major bioactive components. LA insufficiency is reported to cause hair loss. However, its mechanism of action is not clearly known. Here, we explored the efficacy of LA treatment on preventing hair loss and its underlying mechanism of action. We found that LA treatment activated Wnt/β-catenin signaling and induced dermal papilla cell (DPC) proliferation in cell proliferation assays. Moreover, it increased the expression of cell cycle proteins such as cyclin D1 and cyclin-dependent kinase 2. LA treatment also increased the expression of vascular endothelial growth factor, insulin-like growth factor-1, hepatocyte growth factor, and keratinocyte growth factor in a concentration-dependent manner and significantly inhibited that of DKK-1, induced by dihydrotestosterone. These findings suggest that LA treatment induces hair growth by increasing DPC proliferation and alleviates androgenic alopecia by activating Wnt/β-catenin signaling in DPCs.

Recent technological improvements have made abundant changes in construction industry. In specific, some technical applications, such as Building Information Modeling (BIM) opens up many possibilities. Some studies have articulated the use of BIM and its advantages in construction, but most of them are theoretical, not practical. This study is to provide an insight to such obstacles in BIM research. By investigating a real project that could utilize BIM in planning and construction phases, the authors try to investigate a possible outline of advantages in BIM implementation. The study area was set to a railway construction site in South Korea. The site covers a multiple railway tracks, stations, telecommunication facilities, infrastructure facilities, railway structures, and so numerous. In the site, the authors have identified 12 errors in 7 projects that could be prevented if BIM was utilized before the construction. The total upfront costs required to provide a BIM for 7 projects were $116,348. On the other hand, the total costs required to fix the errors in 7 projects were $166,486. This can be regarded as the benefits of using BIM because if BIM was implemented then the associated errors are easily replaced. Therefore, the benefit-cost ratio can be estimated as 1.32 for one-month delay and 1.36 for a three-month delay.

The aim of this study is to investigate transient dynamic flow characteristics of the fluid flow through 5-way electric coolant valve (PCCV : Penta-Control Coolant Valve). To achieve this goal, the present paper attempts the three-dimensional dynamic simulation of the fluid flow through the valve using a commercial CFD solver with moving mesh technique to consider flow inertia and dynamic flow in the opening and closing stages of the ball valve rotating motion. Firstly, dynamic flow characteristics and the thermal mixing inside the PCCV ball valve during the opening and closing stage was analyzed. It is found that the discrepancies between dynamic and steady state simulation is remarkable when fluxes with different levels of enthalpy and momentum flow into the PCCV leads to strong flow interference and flow inertia, while the discrepancies are relatively small at low rotation speed and weak flow interference. Then, the effect of dynamic flow characteristics of the valve on dynamic thermal mixing characteristics at two different ball valve rotational speeds and rotational directions were investigated. It was found that the dynamic flow and thermal mixing characteristics inside the PCCV are greatly affected by the rotation speed, rotation direction, and degree of flow interference between fluxes. It is helpful for the design of the better coolant control strategies and the improvement of the FCEV thermal management system.

Targeted next-generation sequencing (NGS) technology detects specific mutations that can provide treatment opportunities for colorectal cancer (CRC) patients. We included 145 CRC patients who underwent surgery. We analyzed the mutation frequencies of common actionable genes and their association with clinicopathological characteristics and oncologic outcomes using targeted NGS. Approximately 97.9% (142) of patients showed somatic mutations. Frequent mutations were observed in TP53 (70%), KRAS (49%), and APC (47%). TP53 mutations were significantly linked to higher overall stage (p=0.038) and lower disease-free survival (DFS) (p=0.039). ATM mutation was significantly associated with higher tumor stage (p=0.012) and shorter overall survival (OS) (p=0.041). Stage 3 and 4 patients with ATM mutations (p=0.023) had shorter OS, and FBXW7 mutation was significantly associated with shorter DFS (p=0.002). In multivariate Cox regression analysis, ATM mutation was an independent biomarker for poor prognosis of OS (p=0.022). TP53 and FBXW7 mutations are independent biomarkers for poor prognosis of DFS (p=0.042 and 0.030, respectively). A comprehensive analysis of the molecular markers for CRC can provide insights into the mechanisms underlying disease progression and help optimize a personalized therapy.

This study investigated the relationship of acrosome reactions and fatty acid composition on fertility in boar sperm. The acrosome reaction of sperm was induced via methyl-beta-cyclodextrin (MBCD), and acrosome reaction, plasma membrane integrity, and fertility were analyzed. The fatty acid composition of the excess acrosome reacted sperm was determined via gas chromatography. The results showed that the acrosome reaction in sperm was induced over 85% of the time by 60 mM MBCD treatment, and the plasma membrane integrity was significantly decreased and was dependent on the MBCD level. The acrosome reacted sperm resulted in significantly higher saturated fatty acids (SFAs) and lower unsaturated fatty acids (PUFAs) than the non-acrosome reaction group. Moreover, the acrosome reacted sperm from 60 mM MBCD significantly decreased in vitro fertility and blastocyst formation relative to non-acrosome reacted sperm, and the acrosome reaction was positively correlated with SFAs and negatively correlated with PUFAs. Of these fatty acids, C22:5n-6 (docosapentaenoic acid [DPA]) and C22:6n-3 (docosahexaenoic acid [DHA]) were directly negatively correlated with the acrosome reaction (r = -0.982 and -0.947, respectively). In conclusion, the excessive acrosome reactions may occur by reducing the PUFAs, which may then dramatically decrease sperm fertility in pigs.

Hair loss attributed to excessive stress from work and lifestyle changes has become a growing concern, particularly among young individuals. However, currently used drugs such as minoxidil and finasteride impose a plethora of side effects. Therefore, natural substances as alternatives have garnered research interest. A recent study showed the efficacy of Malva verticillata seed extracts in alleviating hair loss via upregulation of the Wnt/β-catenin signaling pathway. In this study, the efficacy of M. verticillata seed extracts on alleviation of hair loss was further investigated. Further fractionation and purification of the seed extracts using silica gel column chromatography and preparative high-performance liquid chromatography helped identify linoleic acid (LA) and oleic acid as the major bioactive components. LA insufficiency is reported to cause hair loss. However, its mechanism of action is not clearly known. Here, we explored the efficacy of LA treatment on preventing hair loss and its underlying mechanism of action. We found that LA treatment activated Wnt/β-catenin signaling and induced dermal papilla cell (DPC) proliferation in cell proliferation assays. Moreover, it increased the expression of cell cycle proteins such as cyclin D1 and cyclin-dependent kinase 2. LA treatment also increased the expression of vascular endothelial growth factor, insulin-like growth factor-1, hepatocyte growth factor, and keratinocyte growth factor in a concentration-dependent manner and significantly inhibited that of DKK-1, induced by dihydrotestosterone. These findings suggest that LA treatment induces hair growth by increasing DPC proliferation and alleviates androgenic alopecia by activating Wnt/β-catenin signaling in DPCs.

Whole blood viscosity, a hemorheological factor, is currently used for diagnosis, as it is correlated with various vascular diseases that are difficult to diagnose early with a general blood test. It was determined that it was necessary to set reference intervals for further studies and utilization of whole blood viscosity in cats, a representative companion animal, and this study was conducted. 50 healthy cats were recruited for the study and whole blood viscosity, complete blood count, and serum chemistry tests were performed. The reference intervals of whole blood viscosity were 15.169 to 43.684 cP at a shear rate of 1 s-1 reflecting diastole, and 3.524 to 5.544 cP at a shear rate of 300 s-1 reflecting systole. Red blood cells, hematocrit, hemoglobin, white blood cells, and neutrophils in the complete blood count, and total protein, albumin, globulin, and cholesterol in the serum chemistry were significantly correlated with whole blood viscosity. The results of this study set reference intervals of whole blood viscosity for healthy cats in a wide shear rate range that has not yet been fully established and investigated its correlation with other blood indicators.

The CCAAT/enhancer-binding protein β (C/EBPβ) is a transcription factor that regulates cellular proliferation, differentiation, apoptosis and tumorigenesis. Although the pro-oncogenic roles of C/EBPβ have been implicated in various human cancers, how it contributes to tumorigenesis or tumor progression has not been determined. Immunohistochemistry with human non-small cell lung cancer (NSCLC) tissues revealed that higher levels of C/EBPβ protein are expressed compared to normal lung tissues. Knockdown of C/EBPβ by siRNA reduced the proliferative capacity of NSCLC cells by delaying G₂/M transition of the cell cycle. In C/EBPβ-knockdown cells, a prolonged increase in phosphorylation of cyclin dependent kinase 1 at tyrosine 15 (Y15-pCDK1) was displayed with increased Wee1 and decreased Cdc25B expression, simultaneously. ChIP analysis showed that C/EBPβ bound to distal promoter regions of WEE1 and repressed WEE1 transcription through the interaction with histone deacetylase 2. Treatment of C/EBPβ-knockdown cells with a Wee1 inhibitor induced a decrease in Y15-pCDK1 and recovered cells from G₂/M arrest. In the xenograft tumors, the depletion of C/EBPβ significantly reduced tumor growth. Taken together, these results indicate that Wee1 is a novel transcription target of C/EBPβ that is required for the G₂/M phase of cell cycle progression, ultimately regulating proliferation of NSCLC cells.

Motivated by empirical observations, we propose a possible extension of Gibrat's law. By applying it into the random growth theory of income distribution (Gabaix, 2009), we find that the income distribution is described by a generalized Pareto-type distribution (GPD) with three parameters. We observe that there is a parameter /elta in the GPD that plays a key role in determining the shape of income distribution. By using the Kolmogorov-Smirnov test, we empirically show that, for typical market-economy countries, /elta is close to 0 significantly, such that the income distribution is characterized by a two-class pattern in which the bottom 90% of the population is approximated by an exponential distribution and the richest 1%~3% is approximated by an asymptotic power law. However, we empirically find that, for China both in planned economy period and in early stages of market reformation (from 1978 to 1990), /elta is significantly deviated from 0, such that the bottom of the population no longer conforms to an exponential distribution.

Purpose: The intervertebral disc is a leading avascular organ in the body that may gather nutrition through diffusion. It maintains homeostasis by the use of autophagy and apoptosis to survive in unfavorable conditions such as stress and mechanical force. Therefore, excessive force and stress beyond normal conditions may cause intervertebral disc degeneration. The purpose of this study was to examine which is the better method, either external fixator (EF) or saline injection (SI), for inducing autophagy and apoptosis-mediated nucleus pulposus (NP) cell death in the discs of rat tail’s. Methods: Sixteen, nine-weeks-old male Sprague–Dawley rat tails were treated with 0.9% saline and EF (two-cross Kirschner wires) for a period ofsix and twelve weeks. Treated discs were dissected to identify the participation of autophagy and apoptosis in intervertebral disc degeneration. For identification purposes, H&amp;E staining, Masson’s trichrome staining, and immunohistochemistry (IHC) for LC3, beclin-1, and P62 in addition to MMP-2, MMP-3, and TIMP-1 were performed. Furthermore, we performed real-time polymerase chain reaction (RT-PCR) to observe autophagy-related gene expression (beclin-1, LC3, and P62) and apoptosis-related gene expression (MMP-2, MMP-3, and TIMP-1). Results: TheEF group showed more insidious NP cell degeneration than the control (Ctrl) group. Degeneration was elevated with increasing compression duration of EF group, whereas the SI group could not distinguish the margin of annulus fibrosus (AF) and NP cells. LC3, beclin-1, and P62 showed the highest and lateral expression whilst MMP-2, MMP-3, and TIMP-1 showed up-regulated and central expression in both groups, although the SI group could not recognize the boundary between NP and AF cells. The EF group showed the highest autophagy-related gene expression whereas the SI group showed lower expression. In addition, the EF group showed more autophagy-accumulating materials than the SI group which elevated with increasing compression duration. Furthermore, the SI group induced the highest apoptotic gene expression, but the EF group showed the lowest expression. Conclusion: The EF method was better for studying autophagy and apoptosis because it enhanced intervertebral disc degeneration after compression, which is actively linked to autophagy and apoptosis. The degeneration process was elevated by increasing the compression duration, but SI could not distinguish AF and NP cell margins.

The whole genome sequencing (WGS) has become a crucial tool to understand genome structure and genetic variation. The MinION sequencing of Oxford Nanopore Technologies (ONT) is an excellent approach for performing WGS and has advantages in comparison with other Next-Generation Sequencing (NGS): It is relatively inexpensive, portable, has simple library preparation, can be monitored in real-time, and has no theoretical limits on read length. Sorghum bicolor (L.) Moench is diploid (2n = 2x = 20) with a genome size of about 730 Mb, and its genome sequence information is released in the Phytozome database. Therefore, sorghum can be be used as a good reference. However, plant species have complex and large genomes compared to animals or microorganisms. As a result, complete genome sequencing is difficult for plant species. MinION sequencing that produces long-reads can be an excellent tool to overcome the weak assembly of short-reads generated from NGS by minimizing the generation of gaps or covering the repetitive sequence that appears on the plant genome. Here, we conducted the genome sequencing for S. bicolor cv. BTx623 using the MinION platform and obtained 895,678 reads and 17.9 gigabytes(Gb) (ca. 25X coverage of reference) from long-read sequence data. Through a de novo assembly using two different tools and mapped assembled contigs against the sorghum reference genome, a total of 6,124 contigs (covering 45.9%) were generated from Canu, and a total of 2,661 contigs (covering 50%) were generated from Minimap and Miniasm with a Racon pipeline. Our results provide a pipeline of long-read sequencing analysis for plant species using the MinION platform and a clue to determine the total sequencing scale for optimal coverage based on various genome sizes.

The reaction mechanism of the carboxylation of K-2-naphthoxide was investigated by density functional theory calculations and spectroscopic studies. The reaction intermediates and products were confirmed by CO₂ adsorbed-FTIR and ¹H-NMR measurements. Four steps of the reaction pathway were identified: CO₂ activation, electrophilic substitution, CO₂-K complex rearrangement, and H-shift, producing 2-hydroxy-1-naphthoic acid (2,1-HNA), 2-hydroxy-3-naphthoic acid (2,3-HNA), and 2-hydroxy-6-naphthoic acid (2,6-HNA). The occurrence of CO₂-K complex rearrangement was also confirmed. These energy profiles of reaction pathways for the reaction intermediates were well consistent the experimental results on the carboxylation of K-2-naphthoxide.

Abstract: Global ecological concern regarding the transfer of fouling organisms to ship hulls is increasing. This study investigated the species composition, dominant species, distribution patterns, community structure, and life-cycle differences of hull-fouling macroinvertebrates on five research vessels (R/Vs: Isabu, Onnuri, Eardo, Jangmok 1, and Jangmok 2) operated by the Korea Institute of Ocean Science and Technology (KIOST). Hull-fouling macroinvertebrates were collected three to five times on quadrats from the upper and middle sectors of the hull sides, bottom, and niche areas (the propellers and shafts and the thrusters). A total of 47 macroinvertebrate species were identified, represented by 8,519 individuals(ind.)/m2 and a biomass of 1,967 gWWt/m2 on the five vessels. The number of species, density, and biomass were greater on the coastal vessels the Eardo, Jangmok 1, and Jangmok 2 than on the ocean-going vessels the Isabu and Onnuri. Among the coastal vessels, barnacles were the most abundant and had the greatest density, while mollusks had the highest biomass. Differences between hull sectors showed that the highest species abundance and density appeared on all hulls in ports and bays where the Jangmok 1 operated, while the highest species abundance, density, and biomass were identified in the niche areas of the Eardo, which operated farther from the coast. The hull-fouling macroinvertebrates that exceeded 1% of all organisms were the barnacles Amphibalanus amphitrite, Balanus trigonus, and Amphibalanus improvisus; the polychaete Hydroides ezoensis; the bivalves Magallana gigas and Mytilus galloprovincialis; and the amphipod Jassa slatteryi. The dominant species were cosmopolitan and globally distributed, and many of them were cryptogenic. Six native species were identified: M. gigas, H. ezoensis, the amphipod Melita koreana, the isopod Cirolana ko-reana, and the barnacle B. trigonus and F. kondakovi. Eight non-indigenous species (NIS) were de-tected: barnacles A. amphitrite and A. improvisus, the bivalve M. galloprovincialis, the polychaete Perinereis nuntia, amphipods J. slatteryi and Caprella californica, and bryozoans Bugulina californica and Bugula neritina. Of the fouling macroinvertebrates found on the vessel hulls, 13% were native and 17% were NIS. The nMDS ordination analysis of the five vessels showed four clusters of fouling macroinvertebrate communities: two ocean clusters (the Isabu and Onnuri), one coastal cluster (the Eardo and Jangmok 2), and one local cluster (the Jangmok 1). More diverse communities developed on the hulls of vessels that operated locally rather than globally or in deep oceans. Spearman rank correlation showed that biological indices such as number of species, density, and biomass correlated highly and positively with the numbers of days on coastal operations and negatively with the number days on ocean operations. The species diversity index correlated positively with the total number of anchoring days and coastal operation days and negatively with the total number of operation days and ocean operation days. The macroinvertebrates differed by the area of operation, the port of anchorage, the number of days in operation and at anchor, and the hull sectors. There is no previous research data on hull-fouling macroinvertebrates in the Republic of Korea, and this study provides a basis for future studies to identify introduced species and their differences based on operation area.

Although the number of unwed mothers have mental health problems and intellectual disability, little research have focused on their mental and cognitive status. Since there has been public stigma of unwed mother in South Korea, they tend to conceal their status and less likely to seek psychiatric and psychological help. In this context, this study aims to assess current status of their mental health and intellectual characteristics. A total 48 unwed mothers from two shelter homes in South Korea were agreed to participate in the study. To compare mental health and intellectual abilities of unwed mothers with the general women population, reference data from national studies was used. Unwed mothers were more likely to have mood disorder, post traumatic stress disorder(PTSD), alcohol and nicotine use disorder, attention-deficit hyperactivity disorder (ADHD) than the general women population. Among 48 participants, 20 (41.7%) were lower than 70 Intelligence Quotient (IQ) and the mean of IQ (78.31) was significantly lower than normalized IQ mean of general women population. In logistic regression analysis, psychiatric disorders were associated intellectual disability. This study confirmed that unwed mothers dwelling in Korean shelter homes have more experience of mental disorders and lower intellectual ability than general women population.

An 11-month-old castrated male Pomeranian presented with nonunion following a femoral fracture that occurred after femoral head and neck osteotomy. Radiography and computed tomography revealed severe atrophy of the proximal bone fragment and retardation of the ipsilateral distal fragment and tibia. An autogenous bone graft using coccygeal bone was performed, in which three-and-a-half coccyges were placed in series and fixed using an orthogonal locking plate. To promote bone healing and facilitate proper weight bearing and ambulation, bone morphogenetic proteins, biphasic calcium phosphate, platelet-rich plasma, passive range of motion exercises, transcutaneous electrical nerve stimulation, neuromuscular electrical stimulation, and low level laser therapy were applied. During the four-year follow-up, it was observed that the previously engrafted bone healed well and maintained stability over a prolonged period, resulting in the patient being able to walk and trot comfortably with good outcomes. However, some degree of lameness was noted during galloping owing to limb shortening and joint contracture.

In the era of big data, feature engineering has proved its efficiency and importance in dimensionality reduction and useful information extraction from original features. Feature engineering can be expressed as dimensionality reduction and is divided into two types of methods such as feature selection and feature extraction. Each method has its pros and cons. There are a lot of studies to combine these methods. Sparse autoencoder (SAE) is a representative deep feature learning method that combines feature selection with feature extraction. However, existing SAEs do not consider the feature importance during training. It causes extracting irrelevant information. In this paper, we propose a parallel guiding sparse autoencoder (PGSAE) to guide the information by two parallel guiding layers and sparsity constraints. The parallel guiding layers keep the main distribution using Wasserstein distance which is a metric of distribution difference, and it suppresses the leverage of guiding features to prevent overfitting. We perform our experiments using four datasets that have different dimensionality and number of samples. The proposed PGSAE method produces a better classification performance compared to other dimensionality reduction methods.

The work proposes a backtesting analysis in comparison between the Lee-Carter and the Cairns-Blake-Dowd mortality models, employing Italian data. The mortality data come from the Italian National Statistics Institute (ISTAT) database and span the period 1975-2014, over which we computed back-projections evaluating the performances of the models in comparisons with real data. We propose three different backtest approaches, evaluating the goodness of short-run forecast versus medium-length ones. We find that both models were not able to capture the improving shock on the mortality observed for the male population on the analyzed period. Moreover, the results suggest that CBD forecast are reliable prevalently for ages above 75, and that LC forecast are basically more accurate for this data.

Agriculture (crop production, land use, and livestock) is the second most important greenhouse gas (GHG) emitting sector after the energy sector. Agriculture is also recognized as the source and sink of GHGs. Evidence demonstrates that the application of high amounts of nitrogen-rich fertilizers enhances methane (CH4) and nitrous oxide (N2O) emissions, which are potent GHGs with a high global warming potential (GWP). Considering its global contribution to the climate crisis, reducing GHG emissions in agriculture would considerably lower its share of the global GHG emission records, which may lead to enormous benefits for the environment and food production systems. Several diverging and controversial views questioning the actual role of plants in the current global GHG budget continue to nourish the debate globally. We must acknowledge that considering the beneficial roles of major GHGs to plants at a certain level of accumulation, implementing GHG mitigation measures from agriculture is indeed a complex task. This review seeks to provide key approaches for GHG mitigation in the literature (environmentally friendly crop cultivation and residue management practices, improvement of plants nutrients/fertilizer use efficiency, exploring the genetic diversity for low GHG emission, soil methane-producing bacteria, integrated soil fertility management, improved livestock feeding efficiency, and production, etc.). This work gathers key approaches from 275 peer-reviewed publications, including experimental research papers, review articles, and books, discussing greenhouse gas emissions mechanisms and mitigation to unravel effective strategies for GHG mitigation, proven to be effective or carry the potential to mitigate GHG generation from agriculture. This review also discusses in depth the significance and the dynamics of strategies regarded as game changers with a high potential to enhance, in a sustainable manner, the resilience of agricultural systems. Agricultural GHG mitigation approaches discussed in this work can serve as game changers in global efforts to reducing GHG emissions and alleviating the impact of climate change through sustainable agriculture and informed-decision making.

Studies have shown increased nontuberculous mycobacterial pulmonary disease (NTM) incidence with inhaled corticosteroid (ICS) use in patients with chronic respiratory diseases; however, this association in chronic obstructive pulmonary disease (COPD) remains insufficiently studied. Using a nationwide population-based database of the Korean National Health Insurance Service, newly diagnosed COPD patients (20052018) treated with inhaled bronchodilators were selected. An NTM case was defined by the presence of the first diagnostic code following inhaled bronchodilator use. Results indicated that ICS users did not have an increased risk of NTM disease compared to non-ICS users (hazard ratio [HR], 1.121; 95% confidence interval [CI], 0.9501.323; p = 0.1755). The highest quartile of the cumulative ICS dose was associated with the development of NTM (1.200, 0.9501.323, p = 0.0497). Medium (1.229, 1.0081.499, p = 0.0410) and high daily doses of ICS (1.637, 1.2412.160, p = 0.0005) were associated with an increased risk of NTM disease. There was no difference in the risk of NTM according to ICS type. ICS use may not increase the risk of developing NTM disease in patients with COPD. However, physicians should weigh the potential benefits and risks of ICS, especially when using high doses and prolonged durations.

This study investigates the application of frequency augmentation techniques to improve condition-based maintenance (CBM+) systems for airborne weapon systems, focusing on the predictive accuracy of velocity and acceleration parameters. Utilizing MIL-STD-1553B MUX data from 138 sorties of fixed-wing aircraft, we explored six augmentation methods, including traditional interpolations (linear, quadratic, cubic spline) and advanced machine learning models (K-Nearest Neighbor, LSTM, and Bi-LSTM). Our findings indicate that while traditional methods like linear interpolation are more effective for velocity parameters, advanced ML techniques, particularly Bi-LSTM, provide better results for acceleration parameters, which exhibit more complex and rapid variability. The study underscores the necessity of tailoring augmentation approaches to specific parameter characteristics and highlights the potential of ML models in capturing intricate patterns within time-series data. These insights are critical for advancing CBM+ systems in military avionics, enhancing reliability and operational efficiency through improved data processing strategies. Future work should explore more performant augmentation techniques, such as by integrating multi-dimensional datasets, and explore ways to develop automated tools for a more powerful predictive maintenance framework.

Optic nerve sheath diameter (ONSD) can help predict the neurologic outcome of patients with post-cardiac arrest (CA) return of spontaneous circulation (ROSC). We aimed to investigate the effect of ONSD changes before and after CA on neurologic outcomes in patients with ROSC after CA using brain computed tomography (CT). The study included patients hospitalized after CA, who had undergone pre- and post-CA brain CT from January 2001 to September 2020. The patients were divided into good and poor neurologic outcome (GNO and PNO, respectively) groups based on the neurologic outcome at hospital discharge. We performed between-group comparisons of the amount and rate of ONSD changes on brain CT and calculated the area under the curve (AUC) to determine their predictive value for neurologic outcomes. Among the 96 enrolled patients, 25 had GNO. Compared to the GNO group, the PNO group showed significantly higher amount (0.30 vs. 0.63 mm; p=0.030) and rate of change (5.26 vs. 12.29 %; p=0.041). The AUC for predicting PNO was 0.64 (95% CI=0.53–0.73; p=0.04) and patients with a rate of ONSD change &gt;27.2% had PNO with 100% specificity and positive predictive value. Hence, ONSD changes may predict neurologic outcomes in patients with post-CA ROSC.

Emerging evidence indicates that intracellular calcium (Ca2+) levels and their regulatory proteins play essential roles in normal stem cell proliferation and differentiation. Cancer stem-like cells (CSCs) are subpopulations of cancer cells that retain characteristics similar to stem cells and play an essential role in cancer progression. Recent studies have reported that the Orai3 calcium channel plays an oncogenic role in human cancer. However, its role in CSC remains underexplored. In this study, we explored the effects of Orai3 in the progression and stemness of oral/oropharyngeal squamous cell carcinoma (OSCC). Orai3 expression was increased in a stepwise manner during the progression of OSCC. In addition, Orai3 was highly enriched in CSC populations of OSCC. Ectopic Orai3 expression in non-tumorigenic immortalized oral epithelial cells increased intracellular Ca2+ levels, acquiring malignant growth and CSC properties. Conversely, silencing of endogenous Orai3 in OSCC cells suppressed CSC phenotype, indicating a pivotal role of Orai3 in CSC regulation. Moreover, Orai3 markedly increased the expression of inhibitor of DNA binding 1 (ID1), a stemness transcription factor. Orai3 and ID1 were highly expressed in CSCs compared to non-CSCs, implying the functional importance of the Orai3/ID1 axis in CSC regulation. Furthermore, suppression of ID1 abrogated CSC phenotype in the cell with ectopic Orai3 overexpression and OSCC. Our study reveals that Orai3 is a novel functional CSC regulator in OSCC and further suggests that Orai3 plays an oncogenic role in OSCC by promoting cancer stemness via ID1 upregulation.

This paper proposed a triangular inequality-based rewiring method for the Rapidly exploring Random Tree (RRT)-Connect robot path-planning algorithm that guarantees the planning time compared to the RRT algorithm, to bring it closer to the optimum. To check the proposed algorithm’s performance, this paper compared the RRT and RRT-Connect algorithms in various environments through simulation. From these experimental results, the proposed algorithm shows both quicker planning time and shorter path length than the RRT algorithm and shorter path length than the RRT-Connect algorithm with a similar number of samples and planning time.

The bark of Rhus verniciflua Stokes (RVS) is used as a food additive and herbal medicine for various inflammatory disorders and cancer in Eastern Asia. RVS exerted anti-inflammatory effects in lipopolysaccharide (LPS)-stimulated RAW264.7 cells, but whether this effect occurs in macrophages after oral administration has not been determined. We used a thioglycollate-induced peritonitis model to obtain macrophages from mice given RVS. We examined the systemic inflammatory response to intraperitoneal LPS. RVS-treated mice had an increased population of peritoneal exudate cells expressing CD11b and SRA. Increased uptake of Alexa Fluor 488-labeled acetylated lipoprotein was observed in monocyte-derived macrophages from RVS-treated mice. When these cells from the RVS group were stimulated with LPS, the levels of tumor necrosis factor (TNF)- and interleukin (IL)-6 in the supernatant decreased, but the level of IL-12 increased. The surface expression of CD86 was reduced, but surface expression of class II MHC molecules was increased. RVS suppressed the serum levels of LPS-induced TNF- and IL-6. RVS enhanced monocyte differentiation in thioglycollate-induced peritonitis by increasing scavenger receptor expression and activity. Macrophages isolated from mice given RVS responded differently to LPS. These findings demonstrate that RVS confers selective anti-inflammatory activity without causing the overall inhibitory effects on immune cells.

Lithium-ion batteries (LIBs) have become indispensable energy storage devices for various applications, ranging from portable electronics to electric vehicles and renewable energy systems. The performance and reliability of LIBs depend on several key components, including the electrodes, separators, and electrolytes. Among these, the choice of binder materials for the electrodes plays a critical role in determining the overall performance and durability of LIBs. This review introduces polymer binders that have been traditionally used in the cathode, anode, and separator materials of LIBs. Furthermore, it explores the problems identified in traditional polymer binders and examines the research trends in next-generation polymer binder materials for lithium-ion battery as alternatives.

This paper proposes two max-pooling engines, named the RTB-MAXP engine and the CMB-MAXP engine, with a scalable window size parameter for FPGA-based convolutional neural network (CNN) implementation. The max-pooling operation for the CNN can be decomposed into two stages, i.e., a horizontal axis max-pooling operation and a vertical axis max-pooling operation. These two one-dimensional max-pooling operations are performed by tracking the rank of the values within the window in the RTB-MAXP engine and cascading the maximum operations of the values in CMB-MAXP engine. Both the RBM-MAXP engine and the CMB-MAXP engine were implemented using VHSIC Hardware Description Language (VHDL) and verified by simulations. They have been employed for and tested in our CNN accelerator targeting at the CNN model YOLOv4-CSP-S-Leaky for object detection.

Lithium sulfur (Li–S) batteries are expected to be very useful for next-generation transportation and grid storage because of their high energy density and low cost. However, their low active material utilization and poor cycle life limit their practical application. The use of a carbon-coated separator in these batteries serves to inhibit the migration of the lithium polysulfide intermediate and increases the recyclability. We report the extent to which the electrochemical performance of Li–S battery systems depends on the characteristics of the carbon coating of the separator. Carbon-coated separators containing different ratios of carbon black (Super-P) and vapor-grown-carbon-fibers (VGCF) were prepared and evaluated in Li–S batteries. The results showed that larger amounts of Super-P on the carbon-coated separator enhanced the electrochemical performance of Li–S batteries; for instance, the pure Super-P coating exhibited the highest discharge capacity (602.1 mAh g-1 at 150 cycles) with a Coulombic efficiency exceeding 95%. Furthermore, the separators with the pure Super-P coating had a smaller pore structure, and hence limited polysulfide migration, compared to separators containing Super-P/VGCF mixtures. These results indicate that it is necessary to control the porosity of the porous membrane to control the movement of the lithium polysulfide.

Workplace bullying is a prevalent issue with a significant impact on employees’ mental health. This study aimed to explore the relationship between workplace bullying and the prevalence of depression with a particular focus on the role of gender. A total of 12,344 Korean employees aged 19–65 years were included in the study. They completed questionnaires including the Korean version of the Occupational Stress Scale, the Oldenburg Burnout Inventory, and the Center for Epidemiologic Studies Depression Scale (CES-D). A score of 16 or higher in CES-D indicated depression. The association between workplace bullying and depression was analyzed using logistic regression analyses. The average CES-D scores were higher for both male and female employees who experienced bullying than for those who did not (p &lt; 0.001). The association between the experience of workplace bullying and the prevalence of depression was statistically significant for both genders, with a stronger correlation observed among male employees (p for interaction &lt;0.001). Organizations are urged to address workplace bullying, particularly for male employees, through the implementation of anti-bullying strategies and policies, as well as the provision of mental health resources and support.

Depressive disorder in childhood and adolescence is a highly prevalent mood disorder that tends to recur throughout life. Untreated mood disorders can adversely impact a patient's quality of life and cause socioeconomic loss. Thus, an accurate diagnosis and appropriate treatment is crucial. However, until now, diagnoses and treatments are conducted according to clinical symptoms. Objective and biological validation are lacking. This may result in a poor outcome for patients with depressive disorder. Research has been conducted to identify the biomarkers that are related to depressive disorder. Cumulative evidence has revealed that certain immunologic biomarkers in-cluding brain-derived neurotrophic factor (BDNF) and cytokines, gastrointestinal biomarkers, hormones, oxidative stress, and certain hypothalamus-pituitary axis biomarkers are associated with depressive disorder. This article reviews the biomarkers related to the diagnosis and treatment of pediatric depressive disorders. To date, clinical biomarker tests are not yet available for diagnosis or for the prediction of treatment prognosis. However, cytokines such as Interleukin-2, interfer-on-gamma, tumor necrosis factor-alpha, and BDNF have shown significant results in previous studies of pediatric depressive disorder. These biomarkers have the potential to be used for diagnosis, prognostic assessment, and group screening for those at high risk.

Sphingosine 1-phosphate (S1P) is a signaling lipid molecule involved in various cellular processes. It is important to develop a quantitative method for S1P to determine endogenous levels and to investigate its functions. Especially since S1P is a tiny lipid component of most biological samples, highly sensitive analysis by LC-MS/MS is required. The main challenge in S1P analysis by chromatography is peak broadening due to the presence of a polar phosphate and zwitterion formation in S1P. In this study, we used hydrogen fluoride (HF) to efficiently remove a phosphate and then analyzed the surrogate, sphingosine, as a sharp peak by LC-ESI-MS/MS. We optimized the dephosphorylation reaction in terms of reaction time, temperature, and HF concentration. Multiple reaction monitoring (MRM) for dephosphorylated form of S1P and C17-S1P as internal standard at m/z transition 300.4&gt;282.4 (quantification ion), 300.4&gt;262.4 (qualification ion), 286.3&gt;268.2 (internal standard). This method was validated by essential parameters such as specificity, linearity, range, LOQ, LOD, accuracy, precision, and repeatability. To confirm this new method, we quantified S1P levels in various serum products (100.02 ~ 284.38 nM). To apply the method in vivo, we analyzed S1P in plasma and kidney tissues obtained from a chronic kidney disease (CKD) mouse model. S1P levels were increased only in CKD kidney tissue but not in plasma. In conclusion, by applying the dephosphorylation step with HF, we established a new sensitive LC-MS/MS quantitative method for S1P that can be applied to biological samples.

Obesity and overweight are associated with many metabolic diseases, such as hypertension, diabetes, and dyslipidemia, which are closely related to a sedentary lifestyle and lack of exercise. Aerobic exercise effectively increases the high-density lipoproteins-cholesterol (HDL-C) levels and decreases the triglyceride (TG) levels. The consumption of Cuban policosanol (Raydel®) is also effective in enhancing the HDL-C quantity and HDL functionality to treat dyslipidemia and hypertension. On the other hand, no study has examined the effects of a combination of high-intensity exercise and policosanol consumption in obese subjects to improve metabolic disorders. In the current study, 17 obese subjects (average BMI 30.0±1.1 kg/m2, eight male and nine female) were recruited to participate in a program combining exercise and policosanol (20 mg) consumption for 12 weeks. After completion, their BMI, waist circumference, total fat mass, systolic blood pressure (SBP), and diastolic blood pressure (DBP) decreased by approximately 15% (p=0.022), 12.7% (p=0.008), 33% (p=0.006), 11% (p<0.046), and 13% (p=0.007), respectively. In the serum lipid profile, at week 12, they showed a remarkable decrease in the total cholesterol (TC) and triglyceride (TG) levels, up to 17% (p<0.019) and 54% (p<0.002) from the baseline, respectively. Although the serum HDL-C was increased by approximately +12% from the baseline, the percentage of HDL-C in TC, HDL-C/TC (%), was increased by up to +32% (p=0.007) at week 12. The serum coenzyme Q10 (CoQ10) level was increased 1.2-fold in all participants at week 12 from the baseline. In particular, the male participants showed a 1.4-fold increase (p=0.027) from the baseline. The larger increase in serum CoQ10 was correlated with the larger increase in the serum HDL-C during 12 weeks. The hepatic function parameters were improved; the serum -glutamyl transferase decreased at week 12 by up to 55% (p<0.007), while the aspartate aminotransferase and alanine transaminase levels decreased within the normal range. In the lipoprotein level, the extent of oxidation and glycation were reduced significantly in VLDL and LDL, with a remarkable decrease in the TG content in particles. The antioxidant abilities of HDL2 and HDL3, such as paraoxonase (PON) and ferric ion reduction ability (FRA), were enhanced significantly by up to 1.8-fold (p<0.001) and 1.6-fold (p<0.001) at week 12. The particle size and number of HDL2 were increased up to +10% during the 12 weeks with a remarkable decrease in the TG content, glycation extent, oxidation up to 32% (p=0.032), 18% (p=0.043), and 11% (p=0.023), respectively. The particle number and diameter of HDL3 were increased by up to +9% with a remarkable increase in the PON activity, FRA activity, and TC content of +82% (p<0.001), +56% (p<0.001), and +32% (p=0.009), respectively. Expression of apolipoproteinA-I in HDL2 and HDL3 were significantly elevated more in both gender around 30~48% with more distinct band intensity and less glycation at week 12. These improvements in HDL quality and functionality were linked to the higher survivability of adult zebrafish and their embryos. Under the co-presence of carboxymethyllysine (CML), a microinjection of HDL2 to zebrafish embryo from week 0 resulted in approximately 47% survivability with developmental defects and attenuated speed. On the other hand, the HDL2 microinjection from week 12 resulted in remarkably higher survivability (~ 70%). In conclusion, 12 weeks of Cuban policosanol (Raydel®, 20 mg) consumption with high-intensity exercise showed significant improvement in blood pressure, body fat mass, blood lipid profile without liver damage, CoQ10 metabolism, and renal impairment. At week 12, all participants showed a remarkable decrease in oxidation and glycation extent in the VLDL and LDL with a decrease in the TC and TG content. Significant enhancement of the qualities and functionalities in HDL2 and HDL3 by the policosanol consumption were also detected: increase in apoA-I content, TC content, particle size, and particle numbers along with antioxidant abilities, such as PON and FRA.

The populations of clearwing moth borers in Korea have recently exploited and severe damage on pin oaks (Quercus palustris Munchh.). We conducted the field monitoring and the molecular analyses to identify them in an integrated manner. Morphological examination and molecular analyses on COI-gene based intra-and inter-specific genetic divergences (GD) were revealed that the borers were recognized as two invasive species, Sphecodoptera sheni and Paranthrenella pinoakula sp. nov.. The maximum intraspecific GD was found to be 1.9%, whereas the minimum interspecific GD was confirmed as 8.1%, with a distinct barcoding gap. Both MJ network and NJ tree were also showed that 18 haplotypes (HAPs) were detected from the 52 COI sequences. The borers were revealed total 17 HAPs: i) H1-H7 were detected from all seven regions with S. sheni; ii) Wonju and Goyang populations of S. sheni were revealed as more than three HAPs; iii) H7 was closely connected with H8 of Chinese population of S. sheni; iv) H9-H10 were detected as the other samples from Wonju population with P. pinoakula sp. n., and closely located with congeneric species. Maximum likelihood tree also revealed that P. pinoacula sp. n. nested within the congeneric species by genetically separating from the S. sheni.

Herein, we developed a highly sensitive and specific bimolecular fluorescence complementation (BiFC)-based influenza A virus (IAV) sensing system created by combining a galactose/glucose-binding protein (GGBP) with an N-terminal large domain (YN1-172) and a C-terminal small domain (YC173-239) of enhanced yellow fluorescence protein (eYFP). The GGBP-based BiFC reporter exhibits the fluorescence reconstitution as a result of conformational changes in GGBP when lactose, derived from 6’-silalyllactose used as a substrate for neuraminidase (NA), binds to GGBP in the presence of IAV. The system showed a linear dynamic range from 1 x 100 TCID50/mL to 1 x 107 TCID50/mL, with a detection limit of 4 x 101 TCID50/mL for IAV (H1N1), demonstrating ultra-high sensitivity. Our system exhibited fluorescence intensity enhancements in the presence of IAV, while displaying weak fluorescence signals when exposed to NA-deficient viruses such as RSV A, RSV B, adenovirus and rhinovirus, thereby indicating selective responses for IAV detection. Taken together, our system provides a simple, highly sensitive and specific IAV detection platform based on BiFC capable of detecting the ligand-induced protein conformational changes, obviating the need for virus culture or RNA extraction processes.

When wastewater containing methylene blue, a cationic dye is improperly treated or immediately dumped into the environment, it can degrade the quality of water bodies and contaminate the ecological environment. The removal of methylene blue from the aqueous solution is critical and urgent. The present work focuses on the use of maize stalk agricultural waste to prepare an adsorbent for the removal of cationic dye (methylene blue) from an aqueous solution. The prepared maize stalk biochar (MSB) was modified with MnO2 and the modified maize stalk biochar was characterized using Fourier transform infrared (FTIR) spectroscopy. Taguchi technique was employed to determine the optimum conditions for the removal of methylene blue (MB) dye from aqueous solution by MMSB. The factors were adsorbent dose (0.5, 1.0 and 1.5 g/100 mL), initial dye concentration (100, 200 and 300 mg/L), contact time (30, 60, 90 minutes) and pH (4, 6 and 8). Among the investigated process factors, adsorption efficiency was influenced by adsorbent dose and initial MB dye concentration. The optimum parameters were 1 g/100 mL adsorbent dose, 100 mg/L initial dye concentration, 60 minutes contact time and a pH of 8.0. This yielded a removal efficiency of 87.49% with adsorption capacity of 206.53 mg/g. The adsorption kinetics agreed with the pseudo-second-order (R2 of 0.999968) model and fitted a Langmuir isotherm (R2 of 0.9795) representing homogeneous monolayer chemisorption.

This paper introduces a fusion convolutional architecture for efficient learning of spatio-temporal features in video action recognition. Unlike 2D CNNs, 3D CNNs can be applied directly on consecutive frames to extract spatio-temporal features. The aim of this work is to fuse the convolution layers from 2D and 3D CNNs to allow temporal encoding with fewer parameters than 3D CNNs. We adopt transfer learning from pre-trained 2D CNNs for spatial extraction, followed by temporal encoding, before connecting to 3D convolution layers at the top of the architecture. We construct our fusion architecture, semi-CNN, based on three popular models: VGG-16, ResNets and DenseNets, and compare the performance with their corresponding 3D models. Our empirical results evaluated on the action recognition dataset UCF-101 demonstrate that our fusion of 1D, 2D and 3D convolutions outperforms its 3D model of the same depth, with fewer parameters and reduces overfitting. Our semi-CNN architecture achieved an average of 16 – 30% boost in the top-1 accuracy when evaluated on an input video of 16 frames.

The global shrimp farming industry is impacted by various infectious diseases, leading to marked production losses. Virulent Vibrio parahaemolyticus strains (VPAHPND) and other Vibrio species cause acute hepatopancreatic necrosis disease (AHPND) in shrimp. We isolated a binary toxin PirA/B-bearing V. campbellii strain (HJ-2023) from a Korean shrimp farm. The biochemical characteristics and antibiotic susceptibility of HJ-2023 were analyzed and compared to those of PirA/B-bearing VPAHPND. Non-AHPND-causing V. campbellii was the control. The pathogenicity of each strain was analyzed in white-leg shrimp. Phylogenetic analysis classified the isolated HJ-2023 strain as V. campbellii. Biochemical tests confirmed distinct properties of HJ-2023, compared to the genetically similar V. harveyi group. The AHPND-causing toxin gene of HJ-2023 showed 100% similarity to the rpoD gene of VCAHPND. An antibiotic disc susceptibility test indicated that HJ-2023 showed resistance to ampicillin, clindamycin, lincomycin, and erythromycin, which is effective against gram-positive bacteria, and showed weak sensitivity to gentamycin. Furthermore, HJ-2023 was 25% less toxic than VPAHPND but could be lethal during aquaculture-related outbreaks. These results highlight the complexity and virulence of AHPND-causing strains through multiple pathways and confirm the pathogenicity of V. campbellii, which increases the risk posed by AHPND to shrimp aquaculture. Our findings could help prevent AHPND.

Marine algae have been considered as abundant source of bioactive compounds with cosmeceutical potential. Recently, a great deal of interest has focused on the health-promoting effects of marine bioactive compounds. Carbohydrate is a major and abundant constitute of marine algae that have been utilized in cosmetic formulations, such as moisturizing and thickening agents. In addition, marine carbohydrates have been suggested as promising bioactive biomaterials for various skin beneficial properties, such as anti-oxidant, anti-melanogenic and anti-skin aging. Therefore, marine algae carbohydrates have potential of skin health benefits for value-added cosmeceutical application. The present review focused on the various biological capacities and potential skin health benefits of bioactive marine carbohydrates.

Surface area and pore size distribution of Eucalyptus samples pretreated by different methods were determined by the Brunauer-Emmett-Teller (BET) technique. Three methods were applied to prepare cellulosic biomass samples for BET measurements: air, freeze, and critical point drying (CPD). Air and freeze drying caused severe collapse of biomass pore structures, but CPD effectively preserved biomass morphology. Surface area of CPD prepared Eucalyptus samples was determined to be 58–161 m2/g, whereas air and freeze dried samples were 0.5–1.3 and 1.0–2.4 m2/g, respectively. Average pore diameter of CPD prepared Eucalyptus samples were 61–70Å. CPD preserved Eucalyptus sample morphology by replacing water with a non-polar solvent, CO2 fluid, which prevented hydrogen bond reformation in the cellulose.

In the process of use and manufacture, carbon fiber foam sandwich structures were often damaged by low-energy impact, resulting in performance degradation. Therefore, it was necessary to study the damage caused by low-speed impact of composite sandwich structures. In this paper, based on Hashin failure criterion, an equivalent finite element model of carbon fiber foam sandwich panel under low velocity impact was established. The model was used to simulate the damage of foam sandwich panel with [±45°/±45°/ (core) /±45°/±45°] ply structure under the impact energy of 10.58J, 21.17J, 31.75J and 42.34J. The simulation results of impact damage depth were compared with the experimental results. The error was less than 10%, which proved the rationality of the impact equivalent model. The model was used to predict and analyze the damage of foam sandwich panels with [±45°/ (core) /±45°], [±45°/ (0°, 90°) / (core) /±45°] and [±45°/ (0°, 90°) (core) / (0°, 90°) /±45°] ply structures under 21.17J impact energy. By comparing and analyzing the damage situation, impact force response time and impact velocity response time, the low energy impact resistance was analyzed. The results showed that increasing the number of ply structure of [±45°] can reduce the impact damage degree and improve the bearing capacity of sandwich panels.

In the crustacean immune system, leucine-rich repeat (LRR) is one of the major structures for recognizing pathogen-associated molecular patterns (PAMPs). LRR domain-containing proteins belong to the LRR family, which is a large group of proteins with more than 6000 genes in the database. They are involved in very diverse physiological functions mainly by interacting with other proteins. In a previous study, the LvLRRm, a transmembrane protein containing only LRR domain, was identified in the white leg shrimp, Litopenaeus vannamei. Its versatile role in performing multiple immunomodulation activities has been reported. However, there is still a lack of research on its efficient function at the protein level. To investigate its interactions with other proteins, we applied a convenient method called ‘Hybrid LRR technique’ to produce a recombinant LvLRRm. The LvLRRm and hagfish’s variable lymphocyte receptors (VLRs) fragments were fused to the conserved LxxLxLxxN motif while retaining the β-strand. In addition, we established interactions between hybrid-proteins and flagellin of Salmonella by performing surface plasmon resonance (SPR) analysis. The designed hybrid proteins showed potential for universal applications without losing protein functions.

Cisplatin is a widely used anticancer drug for treating solid tumors, but it is associated with severe side effects, including nephrotoxicity. Various studies have suggested that the nephrotoxicity of cisplatin could be overcome; nonetheless, an effective adjuvant drug has not yet been established. Oleanolic acid acetate (OAA), a triterpenoid isolated from Vigna angularis, is commonly used to treat inflammatory and allergic diseases. This study aimed to investigate the protective effects of OAA against cisplatin-induced apoptosis and necroptosis using TCMK-1 cells and a mouse model. In cisplatin-treated TCMK-1 cells, OAA treatment significantly reduced Bax and cleaved-caspase3 expression, whereas increased Bcl-2 expression. Moreover, in cisplatin-induced kidney injury mouse model, OAA treatment alleviated weight loss in the body and major organs and also relieved cisplatin-induced nephrotoxicity symptoms. RNA sequencing analysis of kidney tissues identified lipocalin-2 as the most upregulated gene by cisplatin. Additionally, necroptosis-related genes such as receptor interacting protein kinase (RIPK) and mixed lineage kinase domain like (MLKL) were identified. In vitro study, the phosphorylation of RIPKs and MLKL was reduced by OAA pretreatment in both cisplatin-treated cells and cells boosted by co-treatment with z-VAD-FMK. In conclusion, OAA could protect the kidney from cisplatin-induced nephrotoxicity and may serve as an anticancer adjuvant.

Objective: The main purpose of the study is to investigate the combined effects of polydeoxyribonucleotide (PDRN) and extracorporeal shock wave therapy (ESWT) sequences on the regenerative processes in atrophied animal muscles. Methods: Thirty male New Zealand rabbits, aged 12 weeks, were divided into five groups: normal saline, PDRN, ESWT, PDRN injection before ESWT, and PDRN injection after ESWT. Following 2 weeks of cast immobilization, the respective treatments were administered to the atrophied calf muscles. Radial ESWT was performed twice weekly. The evaluation included measurements of calf circumference, tibial nerve compound muscle action potential (CMAP), and gastrocnemius (GCM) muscle thickness after 2 weeks of treatment. Histological and immunohistochemical staining, as well as Western blot analysis, were conducted 2 weeks post-treatment. Staining intensity and extent were assessed using semi-quantitative scores. Results: Groups 4 and 5 demonstrated significantly greater calf muscle circumference, GCM muscle thickness, tibial nerve CMAP, and GCM muscle fiber cross-sectional area (types I, II, and total) than in the remaining three groups (p < 0.05), while they did not did not differ significantly in these parameters. Groups 2 and 3 showed the higher values for all the observations compared to group 1 (p < 0.05). Group 4 had the greatest ratio of vascular endothelial growth factor (VEGF) to platelet endothelial cell adhesion molecule-1 (PECAM-1) in the gastrocnemius muscle fibers than in the other four groups (p < 0.05). Western blot analysis revealed significantly higher expression of angiogenesis cytokines in groups 4 and 5 than in the remaining (p < 0.05). Conclusion: The combination of ESWT and PDRN injection demonstrated superior regenerative efficacy for atrophied calf muscle tissue in rabbit models than these techniques alone or saline. Particularly, administering ESWT after PDRN injection yielded the most favorable outcomes in specific parameters.

The economic development and infrastructure of a nation are closely interrelated. In addition, public trust in national infrastructure facilities is closely linked to the preservation of the advantages provided by these facilities to the public. Since the 1970s, Korea has achieved exponential economic growth over a short period of time and the number of infrastructure facilities has increased correspondingly. This compressed economic development has been underpinned by the national infrastructure, whose safety and usability have been excluded from the scope of the development. However, after around 30 years, structural deterioration coupled with general insensitivity to safety in today’s society has considerably reduced public trust in using the infrastructure. Realistically, policies that mainly focus on developing new technologies related to infrastructure construction have led to practical limitations that discourage the development of technologies for maintenance or inspection. Furthermore, current maintenance works face certain limitations caused by various reasons: insufficient budget, increasing number of infrastructure facilities requiring maintenance, shortage of manpower, and rapidly increasing number of aging infrastructure facilities. To overcome these limitations, a new approach is required that is different from general inspection methods under the existing rules and regulations. In this context, this study aimed to explore the efficiency of bridge inspection and maintenance by unmanned aerial vehicles (UAVs) that could observe inaccessible areas, could be conveniently and easily controlled, and could offer high economic benefits. To this end, various tests were performed on elevated bridges, and suitable UAV images were obtained. The obtained UAV images were inspected by using machine vision technology, thereby excluding subjective evaluations by humans. Methods for enhancing the objectivity of the inspection were also discussed. The test results showed that both the efficiency and objectivity of the proposed method were better than those of the existing bridge maintenance and inspection methods.

Aim The use of prophylactic antibiotics prior to colorectal surgery reduces surgical site infections. Cefazolin and metronidazole is a standard regimen. Ampicillin-sulbactam may be an alternative, but the data are limited. We compared the efficacy of ampicillin-sulbactam with cefazolin and metronidazole as prophylactic antibiotics. Methods Patients who underwent colorectal surgery at Inha University Hospital between 2010 and 2020 were treated prophylactically with cefazolin and metronidazole or ampicillin-sulbactam, and observed for 30 days following surgery. The primary outcome was surgical site infections. Secondary outcomes were deep/organ infections and the need for drainage. Results SSIs occurred in 2.6% (17/646) of the ampicillin-sulbactam group and was not inferior to the occurrence in the cefazolin and metronidazole group (3.8%, 21/556). There was no significant difference between the two groups in the secondary outcomes. Conclusion Compared with the cefazolin and metronidazole combination, the ampicillin-sulbactam group is non-inferior as a preoperative prophylactic antibiotic regimen for colorectal surgery.

This study investigated novel quantitative traits loci (QTLs) associated with the control of grain shape and size as well as grain weight in rice. We employed a joint strategy multiple GAPIT (Genome Association and Prediction Integrated Tool) models [(Bayesian-information and Linkage-disequilibrium Iteratively Nested Keyway (BLINK)), Fixed and random model Circulating Probability Uniform (FarmCPU), Settlement of MLM Under Progressive Exclusive Relationship (SUPER), and General Linear Model (GLM)]–High Density SNP Chip DNA Markers (60,461) to conduct a Genome-Wide Association Study (GWAS). GWAS was performed using genotype and grain-related phenotypes of 143 recombinant inbred lines (RILs). Data show that parental lines (Ilpum and Tung Tin Wan Hein 1, TTWH1, Oryza sativa L., ssp. japonica and indica, respectively) exhibited divergent phenotypes for all analyzed grain traits), which was reflected in their derived population. GWAS results revealed the association between seven SNP Chip makers and quantitative trait loci (QTLs) for grain length, co-detected by all GAPIT models on (Chr) 1–3, 5, 7, and 11), were qGL1-1BFSG (AX-95918134, Chr1: 3820526 bp) explains 65.2%–72.5% of the phenotypic variance explained (PVE). In addition, qGW1-1BFSG (AX-273945773, Chr1: 5623288 bp) for grain width explains 15.5%–18.9% of PVE. Furthermore, BLINK or FarmCPU identified three QTLs for grain thickness independently, and explain 74.9% (qGT1Blink, AX-279261704, Chr1: 18023142 bp) and 54.9% (qGT2-1Farm, AX-154787777, Chr2: AX-154787777 bp) of the observed PVE. For t length-to-width ratio, the qLWR2BFSG (AX-274833045, Chr2: 10000097 bp) explains nearly 15.2%–32% of PVE for LWR. Likewise, the major QTL for thousand-grain weight (TGW) was detected on Chr6 (qTGW6BFSG, AX-115737727, 28484619 bp) and explains 32.8%–54% of PVE. The qTGW6BFSG QTL coincides with qGW6-1Blink for grain width and explained 32.8%–54% of PVE. Putative Candidate genes pooled from major QTLs for each grain traits have interesting annotated functions that require functional studies to elucidate their function in the control of grain size, shape, or weight in rice. Genome selection analysis proposed makers useful for downstream marker-assisted selection based on genetic merit of RILs.