Semisolid casting can provide excellent castings, but the nature of the pore-forming mechanisms has not been properly clarified. In the current communication, it was suggested that hydrogen precipitated during slurry making might have a decisive role in the formation of both gas and shrinkage porosity. Intensive stirring at the end of the slurry making process may act as a degassing step. Without the intense stirring, structures of primary slurry particles form around the hydrogen pores, strongly affecting pore formation and feeding during the intensification stage.

TiO2-based building materials have air purification, auto-cleaning and sterilization functions, and these innovative green building materials have great potential for energy-saving and emission reduction applications in the future. However, there are still great challenges in improving photocatalytic efficiency and stability from laboratory to practical applications. In recent years, researchers have done a lot of work to improve the efficiency and stability of TiO2-based building materials. This paper briefly discussed the air purification principle by photocatalytic building, and the preparation techniques of TiO2-based building materials and the strategies to improve the efficiency of TiO2. Moreover, this paper has outlined the key factors that affect the photocatalytic building performance in practical applications, and analyzed the limitations and future development trends. Finally, we proposed some suggestions for further research on photocatalytic buildings and its application in practice, aiming to provide an efficient reference for developing highly efficient and stable photocatalytic building materials. The aim of this paper is to provide effective guidance for the application of TiO2-based photo-catalysts in the field of green buildings, helping to develop more efficient and stable low-carbon buildings for the development of sustainable cities.

To prepare an edible coating with a good preservative effect on sweet cherries, carboxymethyl chitosan (CMCS) and gelatin (GL) were selected as the film-forming matrix in this experiment, and CaCl2 and ascorbic acid (AA) were added as crosslinking agents and antioxidants, respectively. First, the film was prepared by the casting method, and the film formula with better mechanical and barrier performance was filtered out by one-factor and response surface optimization test, and the differences in the preservation effect of different film formulations (CMCS-GL, CaCl2- CMCS-GL, AA -CaCl2- CMCS-GL) on sweet cherries were compared. and then the different film formulations were compared. The difference in film formulation on the preservation effect of sweet cherries was investigated. The results showed that the optimal formulation for an edible film based on CMCS-GL with good performance was CMCS: GL (w:w)=2:1, with the additional amount of 1% glycerol, 2% CaCl2, 0.1% Tween-20, 2% AA, the tensile strength, elongation at break, oxygen permeability and water vapor permeability of the film obtained with this formula were: 16.28 MPa, 71.46%, 1.39×10-12 g- cm/(cm2-s-Pa), 5.10×10-11 cm3-cm/(m2-s-Pa), respectively. In the preservation of sweet cherries, all three film formulations effectively reduced the rotting rate and weight loss during storage while preserving the high hardness and skin color of the fruit. Among them, the formulation AA -CaCl2- CMCS-GL showed the best preservation effect and can be used as a new method for postharvest preservation of sweet cherries.

Amylose content (AC) stands as a pivotal determinant of rice grain quality, primarily governed by the Waxy gene (Wx), with its allelic diversity significantly influencing AC variation. In the current culinary landscape, soft rice varieties, known for their low AC and superior palatability, are particularly sought after by consumers. Notably, many soft japonica rice varieties cultivated in southern China, including the Nangeng series, are characterized by the presence of the Wxmp allele, derived from the ancestral Wxmq allele. While both alleles are associated with reduced AC, there remains a paucity of detailed understanding regarding the interplay between specific functional single nucleotide polymorphisms (SNPs) within these alleles and the overarching rice grain quality. Employing site-directed mutagenesis, we engineered three distinct transgenic rice lines, each harboring either the Wxmp, Wxmq, or Wxb-5c alleles, against the background of the glutinous rice cultivar Nip(wx). This suite of transgenic rice showcased a gradation ingrain transparency inversely correlated to AC, delineating a sequence from Wxmq, signifying the lowest, through Wxmp, to Wxb-5c, indicating the highest. Consequently, this gradation in AC precipitated variations in other rice grain physicochemical attributes, such as the taste value of cooked rice, gel consistency (GC), and starch pasting properties. Furthermore, analyses of gene expression and enzyme activity revealed that the functional SNPs, Ex4-53G/A and Ex5-53T/C, lead to a decline in the GBSSI enzyme activity without affecting expression levels. These findings underscore the potential of harnessing these SNPs in breeding programs aimed at developing soft rice varieties endowed with enhanced culinary qualities.

This paper addresses the effect of both microstructure and relative humidity on the long-term creep properties of sustainable calcium carbonate (CaCO₃) cements. Those can be prepared by mixing amorphous calcium carbonate and vaterite with water. A larger starting amount of vaterite, X_V, within the mixture design gives a higher elasticity and resistance to the specimens due to the larger overall bridging area within the newly formed calcite crystals. Regarding creep properties for a given relative humidity, the amplitude of creep strain decreases with X_V, and makes the relation between the elastic modulus, E, and hardness, H, of the samples to be linear with the contact creep modulus, C. On the other hand, for a given composition, the amplitude of creep increases with the relative humidity, making the contact creep modulus, Ci, to rise exponentially with the elastic modulus, E, and hardness, H, of the specimens. The most probable creep mechanisms for this kind of cement seem to be a combination of microcraking in the early stages and dissolution and reprecipitation of calcite in the long-term (also known as pressure solution theory). The presence of water in pores with increasing relative humidity might enhance the local dissolution of calcite, and hence the creep amplitude.

Meshfree particle method, which is always regarded as a pure Lagrangian approach, is easily represented complicated domain topologies, moving boundaries, and multiphase media. Solving acoustic problems with the mesfree particle method forms a branch of the acoustic wave modeling field, namely, particle-based computational acoustics (PCA). The aim of this paper is to improve the accuracy of using the PCA method to solve two-dimensional acoustic problems, and realize the particle representation with a hybrid meshfree and finite-difference time-domain (FDTD) method for acoustic boundary conditions at both the plane and curved surface. As a widely used Lagrangian meshfree method, the smoothed particle hydrodynamics (SPH) based on the support domain and the kernel function has developed rapidly in recent years. The traditional SPH method is easily implements parallel processing and has been applied in sound wave simulation. As a corrective method with higher accuracy than SPH, the acoustic propagation and scattering in the time domain is simulated with the corrective smoothed particle method (CSPM). Moreover, a hybrid meshfree-FDTD boundary treatment technique is utilized to represent different acoustic boundaries in the Lagrangian approach. In this boundary treatment technique, the parameter value of virtual particles is obtained with the FDTD method, which concerns truncation errors based on the Tayler series expansion. Soft, rigid, and Mur’s absorbing boundary conditions are developed to simulate sound waves in finite and infinite domain. Results of modeling acoustic propagation and scattering show that CSPM is accurate and convergence with exact solutions, and different acoustic boundaries are validated to be effective in the computation.

Abstract: Image aesthetic assessment (IAA) with neural attention has made significant progress due to its effectiveness in object recognition. Current studies have shown that the features learned by convolutional neural networks (CNN) at different learning stages indicate meaningful information. The shallow feature contains the low-level information of images and the deep feature perceives the image semantics and themes. Inspired by this, we propose a visual enhancement network with feature fusion (FF-VEN). It consists of two sub-modules, the visual enhancement module (VE module) and the shallow and deep feature fusion module (SDFF module). The former uses an adaptive filter in the spatial domain to simulate human eyes according to the region of interest (ROI) extracted by neural feedback. The latter not only takes out the shallow feature and the deep feature by transverse connection, but also uses a feature fusion unit (FFU) to fuse the pooled features together with the aim of information contribution maximization. Experiments on standard AVA dataset and Photo.net dataset show the effectiveness of FF-VEN.

This paper studies a model of dynamic compensation and capital structure with managerial traits. We show that Optimistic manager perceives equity as more undervalued than debt, while, confident manager perceives debt as more undervalued than equity. Managerial risk aversion mitigates manager’s bias. The risk aversion of the optimistic manager has a convex effect on the optimal coupon. There exists the level of risk aversion eliminating the bias on the leverage. The managerial optimist has an ambiguous effect on the owner’s bankruptcy level. The risk aversion has a convex effect on the owner’s bankruptcy level. The optimistic/confident manager underestimates the credit spread. The risk aversion has convex effect on the credit spread. In contrast to rational manager, the optimistic/confident manger has higher level of effort. The risk aversion has a negative effect on the effort.

A solid structure, such as a road, building wall or envelop, used as a solar collector is considered an effective and new way to use renewable energy. This paper focused on the temperature characteristics of four structures exposed to sunshine: asphalt, red brick, composite cement and concrete road slab. Furthermore, the collected heat based on a hydraulic system was investigated experimentally. For the four structure slabs, their temperature differences are due to solar radiation absorption varied greatly by the material’s heat absorptance and color. Through the test, asphalt slab attained the highest temperature and had the weakest reflection among the structures. Compared with the others, the temperature of the asphalt slab was greater by 8.1%, 14.9% and 16.4% than the brick, composite cement and concrete, respectively. The reflection intensity growth ratio was defined and indicates the growth potential for absorbing radiation in the solid slab surface. From the experiments, it was concluded that a suitable selection of road materials can greatly improve the thermal absorption, conduction and penetration into the solid slab. The collected heat capability was approximately 250 W/m2 to 350 W/m2 in the natural summer condition. A black coating or a surface modification can collect more heat, reaching greater than 250 W/m2. The solar collecting heat efficiency with a surface configuration of the road slab can reach above 30% in the summer time.

This paper considers the Hermitian solutions of a new system of commutative quaternion matrix equations, we establish both necessary and sufficient conditions for the existence of solutions. Furthermore, we derive an explicit general expression when it is solvable. To illustrate our main findings, we present two numerical algorithms and examples in this paper.

Newly build offshore wind farms (OWFs) render a collision risk between ships and installations. The paper proposed a real-time traffic monitoring method based on machine vision and deep learning technology to improve the efficiency and accuracy of the traffic monitoring system in the vicinity of offshore wind farms. Specifically, the method employs real automatic identification system (AIS) data to train a machine vision model, which is then used to identify passing ships in OWF waters. Furthermore, the system utilizes stereo vision techniques to track and locate the positions of passing ships. The method is tested in offshore water in China to validate its reliability. The results prove that the system sensitively detects the dynamic information of the passing ships, such as the distance between ships and OWFs, ship speed and course. Overall, this study provides a novel approach to enhancing the safety of OWFs, which is increasingly important as the number of such installations continues to grow. By employing advanced machine vision and deep learning techniques, the proposed monitoring system offers an effective means of improving the accuracy and efficiency of ship monitoring in challenging offshore environments.

Chalcones are a class of flavonoids possessing a variety of biological activities, including antimicrobial and antioxidant effects. Therefore, chalcones and their derivatives have potential use in the control of postharvest diseases. In this work, the effects of 2ʹ,4ʹ-dichloro-chalcone on the in vitro growth and in vivo pathogenicity of F. tricinctum and T. roseum were investigated. The results showed that 100 µM of 2ʹ,4ʹ-dichloro-chalcone strongly inhibited mycelial growth and conidial production of F. tricinctum (32.3%) and T. roseum (65.2%) in vitro. This treatment also significantly inhibited the expansion of potato dry rot from F. tricinctum (48.6%) and apple rot spot from T. roseum (36.2%). The incubation of F. tricinctum and T. roseum conidia with this agent for 2 h increased their cell membrane permeability by 25% and 22.5%, respectively and conidial membrane permeability by 41.7 and 65.4%, respectively. This treatment also significantly inhibited the total respiration rate and activated the cyanide-resistant respiratory pathway in both pathogens. Protein immunoblotting showed that the treatment increased alternative oxidase (AOX) levels after 4 h in F. tricinctum and T. roseum by 52.76% and 39.13%, respectively. Conclusion: 100 µM 2ʹ,4ʹ-dichloro-chalcone significantly inhibited mycelial growth and spore production in F. tricinctum and T. roseum in vitro and reduced their pathogenicity in postharvest potato and apple crops. Further analysis indicated that 2ʹ,4ʹ-dichloro-chalcone disrupted the integrity of cell membranes and the mitochondrial respiratory electron transport chain which leaded to ROS burst and oxidative stress, AOXs were induced directly or indirectly, and the cyanide resistant respiratory pathway was activated. The in vitro growth and pathogenicity of F. tricinctum and T. roseum were inhibited.

Aim: We estimated the correlation between serum bilirubin concentrations and insulin resistance in advanced maternal age without diabetes mellitus. Method: The cross-sectional study involved consecutive 50 women of advanced maternal age without diabetes mellitus, and insulin resistance (IR) was diagnosed according to the homeostatic model assessment insulin resistant (HOMA-IR) formula and the cut-off point was set to more than 2.5. Serum bilirubin and HOMA-IR were compared between the IR (+) and IR (-) groups. Results: We found that serum bilirubin levels in the IR subjects were significantly decreased compared to those without IR (p = 0.0252). Serum bilirubin concentrations were negatively correlated with the weight and the fasting insulin concentrations in all subjects (r=−0.282, p=0.047, r=-0.424, p=0.002). Additionally, serum bilirubin had a negatively correlation with HOMA-IR (r = -0.410, p = 0.003) in all subjects. The multiple linear regression analysis found that serum total bilirubin levels were independently correlated with HOMA-IR (beta = -0.392, p= 0.015) in these subjects. Conclusions: The study demonstrated that serum bilirubin concentrations had negatively correlation with insulin resistance in advanced pregnant women without diabetes mellitus, and decreased serum bilirubin may forebode increased gestational diabetes mellitus risk in our study population.

The Mine Internet of Things (MIoT), as a key technology for reconstructing post-disaster communication networks, enables to realize the safety monitoring and controlling of the affected roadway. However, due to the challenging underground mine environment, the MIoT suffers from severe signal attenuation, vulnerable nodes, and limited energy, which result in low network reliability of the post-disaster MIoT. To improve the transmission reliability as well as to reduce energy consumption, a directional-area-forwarding-based energy-efficient opportunistic routing (DEOR) for the post-disaster MIoT is proposed. DEOR defines a forwarding zone (FZ) for each node to route packets toward the sink. The candidate forwarding set (CFS) is constructed by the nodes within the FZ that satisfy the energy constraint and the neighboring node degree constraint. The nodes in CFS are prioritized based on the routing quality evaluation by taking the local attributes of nodes into consideration, such as the directional angle, transmission distance, and residual energy. DEOR adopts a recovery mechanism to address the issue of void nodes. The simulation results validate that the proposed DEOR outperforms ORR, OBRN and ECSOR in terms of energy consumption, average hop count, packet delivery rate, and network lifetime.

Autonomous aerial refueling technology is an effective solution to extend flight duration of unmanned aerial vehicles, and also a great challenge due to its high risk. For autonomous probe-and-drogue refueling tasks, relative navigation to provide relative position between the receiver aircraft and the refueling drogue is the first and essential step, and vision-based method is the most frequently used. A new monocular vision navigation sensor with image processing strategy consisting of the drogue detection method and the tracking method is developed for autonomous aerial refueling in this paper. In the drogue detection method, thresholding and mathematical morphology method are adopted to eliminate image interference, and contours extraction method is applied to obtain all contours, which are then subsequently checked to achieve target contour of drogue. In the tracking method, a rectangle of interest (ROI) of current frame image is determined by positioning results of last frame, and then processed by the previous drogue detection method. Finally, the proposed image processing strategy in monocular vision navigation sensor is validated using real flight images, which are captured from an autonomous aerial refueling testbed using a micro six-rotor aircraft as receiver aircraft.

Land-cover classification that uses very-high-resolution (VHR) remote sensing images is a topic of considerable interest. Although many classification methods have been developed, there is still room for improvements in the accuracy and usability of classification systems. In this paper, a novel post-processing approach based on a dual-adaptive majority voting strategy (D-AMVS) is proposed for improving the performance of initial classification maps. D-AMVS defines a strategy for refining each label of a classified map that is obtained by different classification methods from the same original image and fusing the different refined classification maps to generate a final classification result. The proposed D-AMVS contains three main blocks. 1) An adaptive region is generated by extending gradually the region around a central pixel based on two predefined parameters (T1 and T2) in order to utilize the spatial feature of ground targets in a VHR image. 2) For each classified map, the label of the central pixel is refined according to the majority voting rule within the adaptive region. This is defined as adaptive majority voting (AMV). Each initial classified map is refined in this manner pixel by pixel. 3) Finally, the refined classified maps are used to generate a final classification map, and the label of the central pixel in the final classification map is determined by applying AMV again. Each entire classified map is scanned and refined pixel by pixel based on the proposed D-AMVS. The accuracies of the proposed D-AMVS approach are investigated through two remote sensing images with high spatial resolutions of 1.0 and 1.3 m, respectively. Compared with the classical majority voting method and a relatively new post-processing method called general post-classification framework, the proposed D-AMVS can achieve a land-cover classification map with less noise and higher classification accuracies.

The objective of this study is to design an optimal model predictive control (MPC) strategy using manipulated variables to control the production of a sufficient amount of hydrogen through low temperature autothermal reforming of dimethyl ether (DME), a reforming reaction performed using PdO/ZnO/γ-Al2O3 catalysts coated on honeycomb cordierite ceramics. Experiments and simulation have verified that the optimal activity temperature of the catalyst is 400 °C, and the hydrogen volume fraction in syngas is over 43%. In the implementation of the hydrogen production system, the MPC controller can precisely determine the feed rates of DME, high-purity air, and water based on the space state equation of the reformer, to achieve the anti-disturbance of the reformer temperature. Thus, the reduction of hydrogen yield and sintering of the catalyst as a result of overheating are prevented. As the static and dynamic performance of hydrogen production exhibits excellent tracking of the setpoints, an autonomous, automated, and reliable continuous system was designed to meet the desired hydrogen demand situation. This study shows that an autonomous, automated, and reliable continuous hydrogen production reforming system can be designed to actively respond to the on-board hydrogen usage situation.

Although Eulerian approaches are standard in computational acoustics, they are less effective for certain classes of problems like bubble acoustics and combustion noise. A different approach for solving acoustic problems is to compute with individual particles following particle motion. In this paper, a Lagrangian approach to model sound propagation in moving fluid is presented and implemented numerically, using three meshfree methods to solve the Lagrangian acoustic perturbation equations (LAPE) in the time domain. The LAPE split the fluid dynamic equations into a set of hydrodynamic equations for the motion of fluid particles and perturbation equations for the acoustic quantities corresponding to each fluid particle. Then, three meshfree methods, the smoothed particle hydrodynamics (SPH) method, the corrective smoothed particle (CSP) method, and the generalized finite difference (GFD) method, are introduced to solve the LAPE and the linearized LAPE (LLAPE). The SPH and CSP methods are widely used meshfree methods, while the GFD method based on the Taylor series expansion can be easily extended to higher orders. Applications to modeling sound propagation in steady or unsteady fluids in motion are outlined, treating a number of different cases in one and two space dimensions. A comparison of the LAPE and the LLAPE using the three meshfree methods is also presented. The Lagrangian approach shows good agreement with exact solutions. The comparison indicates that the CSP and GFD method exhibit convergence in cases with different background flow. The GFD method is more accurate, while the CSP method can handle higher Courant numbers.

With increasing demand from unmanned driving and robotics, more attention has been paid to point cloud-based 3D object accurate detection technology. However, due to the sparseness and irregularity of the point cloud, the most critical problem is how to utilize the relevant features more efficiently. In this paper, we proposed a point-based object detection enhancement network to improve the detection accuracy in the 3D scenes understanding based on the distance features. Firstly, the distance features are extracted from the raw point sets and fused with the raw features about reflectivity of the point cloud to maximizing the use of information in point cloud. Secondly, we enhanced the distance features and raw features that we collectively refer to them as self-features of the key points in Set Abstraction (SA) layers with the self-attention mechanism, so that the foreground points can be better distinguished from the background points. Finally, we revised the group aggregation module in SA layers to enhance the feature aggregation effect of key points. We conducted experiments on the KITTI dataset and nuScenes dataset and the results show the enhancement method proposed in this paper has excellent performance.

The 2019 novel coronavirus (2019-nCoV) causes novel coronavirus pneumonia (NCP). Given that approved drug repurposing becomes a common strategy to quickly find antiviral treatments, a collection of FDA-approved drugs can be powerful resources for new anti-NCP indication discoveries. In addition to synthetic compounds, Chinese Patent Drugs (CPD), also play a key role in the treatment of virus related infections diseases in China. Here we compiled major components from 38 CPDs that are commonly used in the respiratory diseases and docked them against two drug targets, ACE2 receptor and viral main protease. According to our docking screening, 10 antiviral components, including hesperidin, saikosaponin A, rutin, corosolic acid, verbascoside, baicalin, glycyrrhizin, mulberroside A, cynaroside, and bilirubin, can directly bind to both host cell target ACE2 receptor and viral target main protease. In combination of the docking results, the natural abundance of the substances, and botanical knowledge, we proposed that artemisinin, rutin, glycyrrhizin, cholic acid, hyodeoxycholic acid, puerarin, oleanic acid, andrographolide, matrine, codeine, morphine, chlorogenic acid, and baicalin (or Yinhuang Injection containing chlorogenic acid and baicalin) might be of value for clinical trials during a 2019-nCov outbreak.

The calcium-sensing receptor (CAS), as a chloroplast thylakoid membrane protein, involved in the process of [Ca2+] ext-induced [Ca2+]cyt increase (CICI) in the plant. However, the underlying mechanism regulating this process is lacking. Furthermore, recent evidence suggests that CAS may perform additional roles in the plant. Here, we provide an update covering the multiple roles of CAS in stomatal movement regulation and calcium signaling in the plant. We also analysis the possible phosphorylation mechanism of CAS by light and discuss the role of CAS in abiotic stress (drought, salt stress) and biotic stresses (plant immune signaling). Finally, we provide a perspective for future experiments which are required to fill gaps in our understanding of the biological function of CAS in the plant.

Codon use bias is an important characteristic in the process of genetic information transmission of species. With the publication of the genome of C. panzhihuaensis, it is of great significance to investigate the codon use bias for understanding the genetic evolution of this species and for molecular breeding. In this study, Perl language and CodonW 1.4.2 software was used to systematically analyze the coding gene sequences of the C. panzhihuaensis genome, obtain the characteristics of codon use, and identify the sources of variation affecting codon use. The results showed that GC3s content, GCall content, and ENC value were 46.75%, 47.67%, and 52.8 respectively. As the first seed plant, the GC3 content of Cycas is similar to that of most gymnosperms and most dicotyledons, but considerably different from that of monocotyledons.RSCU value was greater than 1, among which 21 codons ended in U or A. Enc-plot analysis, PR2-plot neutral plot analysis, and correlation coefficient analysis of Axis1 with GC3s and CAI revealed that the codon bias was mainly affected by natural selection, but also by mutation pressure and other factors. Thirty-one optimal codons of Cycas genes were screened. This research can provide a reference for the phylogeny and genome codon evolution of Cycas.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

We investigate and discuss in detail the structure of the restricted singular value decomposition for a tensor triplet under t-product (T-RSVD). The algorithm is provided with a numerical example illustrating the main result. For applications, we consider color image watermarking processing with T-RSVD.

Many parameters and complex boundaries are involved in the spatial arrangement of an under-ground powerhouse for a hydropower station, which requires reference to many relevant cases and specifications. However, in practical applications, retrieving relevant cases or specifications is difficult, and there is a lack of knowledge of cascading logic among design parameters. For this question, a targeted knowledge graph based on knowledge graph management technology is established to support subsequent applications. This paper proposes a new concept of con-structing a knowledge graph for building information modeling (BIM) underground power-houses of hydropower stations. Firstly, the ontology skeleton of hydropower station spatial ar-rangement design, which represents the knowledge organization structure of the knowledge graph, is reconstructed by carefully analyzing the requirements for intelligent modeling of un-derground powerhouses. A large amount of unstructured data is identified based on optical character recognition (OCR) technology and is divided into words to extract correlation knowledge based on THULAC. In the next step, the knowledge triad of the spatial arrangement of the underground powerhouse is extracted based on ChatGPT and stored in a Neo4j knowledge base to build a knowledge graph. Finally, the knowledge graph is serviced to realize the query of knowledge and parameter recommendation to assist the digital intelligent design of spatial arrangement of an underground powerhouse of pumped storage hydropower stations.

Motivated by empirical observations, we propose a possible extension of Gibrat's law. By applying it into the random growth theory of income distribution (Gabaix, 2009), we find that the income distribution is described by a generalized Pareto-type distribution (GPD) with three parameters. We observe that there is a parameter /elta in the GPD that plays a key role in determining the shape of income distribution. By using the Kolmogorov-Smirnov test, we empirically show that, for typical market-economy countries, /elta is close to 0 significantly, such that the income distribution is characterized by a two-class pattern in which the bottom 90% of the population is approximated by an exponential distribution and the richest 1%~3% is approximated by an asymptotic power law. However, we empirically find that, for China both in planned economy period and in early stages of market reformation (from 1978 to 1990), /elta is significantly deviated from 0, such that the bottom of the population no longer conforms to an exponential distribution.

Speaker recognition methods based on convolutional neural networks (CNN) have been widely used in the security field and smart wearable devices. However, the traditional CNN has a large number of hyperparameters that are difficult to be determined, which makes the model easy to fall into local optimum or even fail to converge during the training process. Intelligent algorithms such as particle swarm optimization and genetic algorithm are used to solve the above problems. However, these algorithms have poor performance compared with the current emerging meta-heuristic algorithms. In this study, the dung beetle optimized convolution neural network (DBO-CNN) is proposed to identify the speakers, which is helpful in finding suitable hyperparameters for training. By testing the dataset of 50 people, it was demonstrated that the accuracy of the model was significantly improved by using this approach. Compared with the traditional CNN and CNN optimized by other intelligent algorithms, the accuracy of DBO-CNN has increased by 0.6%~4.8%, and reached 98.3%.

In order to realize the sustainable utilization of water resources and the sustainable development of economy, the evaluation index system of water use efficiency system and economic development system was constructed. Entropy weight method and comprehensive evaluation method were adopted to determine the index weights and conduct comprehensive evaluation for the two systems. The coupling coordination model was used to calculate the coupling degree, coordination degree and coupling coordination degree of the two systems. The annual coupling stage and coupling coordination intensity of the two systems were analyzed and determined. The results showed that the comprehensive evaluation values of both water use efficiency system and economic development system in Jinan City increased greatly from 2008 to 2017, and showed a changing trend of ups and downs. The two systems were in the antagonistic stage, and were gradually approaching the running-in stage, indicating that they were in the state of common development. The coupling coordination degree of the two systems gradually increased in waves, progressed from the moderately to the highly coordinated coupling. In the future, if the water control path appropriate to Jinan City can be explored actively, the water-saving kinetic energy of economic development can be increased constantly, and the linkage effect between economic development and water resources utilization can be given full play to, the two systems will be in the orbit with the benign interaction and healthy harmonious development.

The Woka-Cuona rift zone, situated in the easternmost portion of southern Tibet, displays complex geological conditions. It consists of three distinct grabens or half grabens, spanning the Himalayan and Gangdese terranes from south to north. Examining the distribution patterns and genetic mechanism of the geothermal system in the Woka-Cuona rift zone holds significant guidance for studying the genetic mechanisms of geothermal systems and the production and utilization of ge-othermal resources in the rift zones of southern Tibet. Based on the geological conditions of the study area, the mechanism of rift formation and the distribution characteristics of geothermal water in the three distinct grabens were analyzed through data collection, ground surveys, geochemical analysis, and isotope analysis. Alongside topographic, drainage, and structural features, the Woka-Cuona rift zone was subdivided into four zones from north to south - Woka, Qiongduojiang, northern Cuona, and southern Cuona grabens. Additionally, the study investigated the geochemical char-acteristics, recharge sources, and water-rock interactions of geothermal water in different zones, providing a scientific foundation for subsequent geothermal energy production.

In the paper, the authors establish two identities to express the generating function of the Chebyshev polynomials of the second kind and its higher order derivatives in terms of the generating function and its derivatives each other, deduce an explicit formula and an identities for the Chebyshev polynomials of the second kind, derive the inverse of an integer, unit, and lower triangular matrix, present several identities of the Catalan numbers, and give some remarks on the closely related results including connections of the Catalan numbers respectively with the Chebyshev polynomials, the central Delannoy numbers, and the Fibonacci polynomials.

Polysaccharide from Ficus carica L. (FCP) exert multiple biological activities, as a biological macromolecule, the available knowledge about the specific structures and mechanisms of biological activity of purified 'Brunswick' fig polysaccharide is currently limited. In the present study, by chemical purification and characteristics identified via specific instruments, and then the impact of FCP on the immunomodulation activity in vitro and in vivo was examined. Structural char-acteristics showed that the molecular weight of the FCP was determined to be 127.5 kDa, the primary monosaccharides present in the FCP were galacturonic acid (GalA), arabinose (Ara), galactose (Gal), rhamnose (Rha), glucose (Glc), and xylose (Xyl) at a ratio of 0.321:0.287:0.269:0.091:0.013:0.011. Based on the investigation of in vitro immunomodulatory ac-tivity, FCP was found to stimulate the production of NO, TNF-α, and IL-6 and increased the pi-nocytic activity of macrophages. Further analysis revealed that FCP activated macrophages by interacting with toll-like receptor 4 (TLR4). Moreover, the in vivo test results indicate that FCP showed significant increase serum pro-inflammatory factors in immunosuppressed mice. Overall, this study suggests that FCP has the potential to be utilized as a novel immunomodulator in the pharmaceutical and functional food industries.

Cu-Sn shape-memory microwires were fabricated by a glass-coated melt spinning method. Effects of Sn content on the microstructure and mechanical property of microwires were investigated. The phase transforms from martensite to austenite with Sn content increasing from 14.0 atomic percent (at.%) to 16.5 at.%, and highly ordered intermetallic phase, δ, formed with higher Sn content. The fracture stress, σf, and the critical stress for martensitic transformation, σMs, increases with Sn content increasing. The mechanical property as well as superelasticity were improved greatly by high cooling rate of the glass-coated melt spinning method.

The hospital indoor environment plays a significant role in shaping the microbial exposures that humans encounter. Resistance to antibiotics is one of the mechanisms employed by bacteria to develop resilience against stress in indoor environments. The extensive usage of antibiotics has been a key factor in driving changes in the ecological function of antibiotic resistance genes (ARGs) and their acquisition by pathogenic bacteria. By integrating the 16S rRNA Illumina sequencing and high throughput-qPCR approaches with water and air dust samples across seven departments at Peking University Shenzhen Hospital, China, this study yielded intriguing findings regarding the department-specific variation, transmission, and correlation of bacteria, ARGs and MGEs within the hospital indoor environment. One notable observation was that the seasonal variation played a vital role in shaping the bacterial composition in the overall hospital indoor environment across seven studied departments. Nevertheless, a similar significant seasonal impact was only observed in the blood test room and emergency departments, rather than in the other five departments. Another intriguing finding was the correlation between ARGs and MGEs abundance. This correlation was evident in the overall hospital indoor environment, which was conversely not found in the emergency, pneumology and gynecology departments. Additionally, while there was no significant relationship that occurred between bacterial communities and ARGs/MGEs within the hospital, the gynecology department demonstrated a close link between bacterial communities and the presence of ARGs/MGEs. Notably, the gynecology department also stood out as an important source of bacteria and ARGs/MGEs for other departments. This study underscores the need for careful surveillance and monitoring of antibiotic resistance, particularly in Legionella spp. in man-made water systems. The findings also show the importance of monitoring and understanding the genetic elements such as Tp614 involved in gene transfer and recombination, as well as their impact on antimicrobial treatment efficacy.

Spider silk has excellent strength and elasticity in natural, researchers have been working for decades try to achieve natural spider silk outstanding mechanical properties using recombinant spider silk protein (spidroin) through artificial spinning. In this work, we chose wet spinning method to explore the relationship between concentration of coagulation bath and fiber performance. It was found that the concentration of methanol has important effect on fiber continuity, diameter and mechanical properties. Lower concentration favors spinning continuous thinner, fibers with high strain. Secondary stretching benefits spinning silk fibers with stable mechanical properties, and thermal stability. Through applying different methanol concentration and additional stretching, we obtained silk fibers with Young’s modulus of 3.052± 2.626 GPa, stress of 25.3944 ± 17.48 MPa, and strain of 140 ± 95.4%.

Genetic engineering and directed evolution are effective methods to address the low yield and poor industrialization level of microbial target products. The current research focus is on how to efficiently and rapidly screen beneficial mutants from constructed large-scale mutation libraries. Traditional screening methods such as plate screening and well plate screening are severely limited in their development and application due to their low efficiency and high costs. In the past decade, microfluidic technology has become an important high-throughput screening technology due to its fast speed, low cost, high automation, and high screening throughput, and it has developed rapidly. Droplet-based microfluidic high-throughput screening has been widely used in various fields such as strain/enzyme activity screening, pathogen detection, single-cell analysis, drug discovery, and chemical synthesis, and has been widely applied in industries such as materials, food, chemicals, textiles, and biomedicine. In particular, in the field of enzyme research, droplet-based microfluidic high-throughput screening has shown excellent performance in discovering enzymes with new functions, improved catalytic efficiency or stability, acid-base tolerance, etc. Currently, droplet-based microfluidic high-throughput screening technology has achieved high-throughput screening of enzymes such as glycosidase, lipase, peroxidase, protease, amylase, oxidase, and transaminase, as well as high-throughput detection of products such as riboflavin, coumarin, 3-dehydroquinate, lactic acid, and ethanol. This article reviews the application of droplet-based microfluidics in high-throughput screening, with a focus on high-throughput screening strategies based on UV, visible, and fluorescence spectroscopy, including labeled optical signal detection screening, as well as label-free electrochemical detection, mass spectrometry, Raman spectroscopy, nuclear magnetic resonance, etc. Furthermore, the research progress and development trends of droplet-based microfluidic technology in enzyme modification and strain screening are also introduced.

To study the oil and gas distribution law in the slope area of the hydrocarbon-bearing basin, the distribution of the effective dominant path of sand bodies transporting oil and gas is a fundamental subject. In this paper, we introduced an effective way to predict such transport paths and applied the method to study the sand bodies of the lower first member of the Shahejie Formation (E3s1L) in the southern area of the Qikou Depression in the Bohai Bay Basin (Qinan). We first define the dominant hydrocarbon transport paths of the sand body as the superimposed area of the contiguously distributed area of the sand body and the paleotectonic ridges at the top of the formation where the sand body is located. Then we define the oil and gas supply area of the oil source fault as the overlapped area of the favorable transport path of oil source faults and the width of the associated fracture zone. Stacking the two areas, we can delineate the distribution of the effective dominant transport paths of the sand bodies. The results from our case study of the Qinan area show that the effective dominant paths of sand bodies transporting oil and gas in the E3s1L Formation in the Qinan area are distributed throughout the region with better development in the west than in the east. The paths in the eastern part extend from north to south, while the paths in the western part extend from northeast to southwest, which is favorable for the convergence of oil and gas generated from the source rocks of the third member of Shahejie Formation (Es3) in the Northeastern main depression of Qikou and the formation of oil and gas accumulations in the l E3s1L Formation. The results are consistent with the fact that oil and gas discovered in the E3s1L Formation in the Qinan region are mainly distributed in the central and western regions, with a small amount in the southeast. Therefore, the suggested method is feasible to predict the effective dominant path of sand bodies transporting oil and gas.

A single fracture is the basic unit of fracture medium, and the roughness of fracture wall surface is an important factor influencing hydraulic characteristics of the flow in bedrock fracture. However, effects of the shape and density of roughness elements (various bulges/pits on rough fracture wall surfaces) on water flow in a single rough fracture have not been thoroughly discovered. Thus the water flow in single fracture with different shapes and densities of roughness elements was simulated by using Fluent software in this study. The results show that in wider fractures the flow rate mainly depends on fracture aperture, while in narrow and close fracture medium the surface roughness of fracture wall is the main factor of head loss of seepage; there is a negative power exponential relation between the hydraulic gradient index and the average fracture aperture, i.e. with the increase of fracture aperture, the relative roughness of fracture and the influence weight of hydraulic gradient both decrease; and in symmetrical-uncoupled fractures there is a super-cubic relation between the discharge per unit width and average aperture. Above results would help to deepen the understanding of rough fracture seepage.

Objective: Identify factors associated with excessive day time sleepiness (EDS) in individuals with obstructive sleep apnea (OSA), and analyze the effects that obesity and gender have on excessive daytime sleepiness in such individuals. Methods: A total of 160 people were selected for this study. All the people have completed a clinical evaluation, and whose apnea-hypopnea index (AHI) > 10 events/hour of sleep on polysomnography were included in the study from the Department of otolaryngology. Results: The Mean age was 43.87±11.34 years, mean EDS score was 14.09± 4.91, and mean AHI was 43.88±20.66 events/hour of sleep. Male presented lower mean age, higher EDS scores, and more time in apnoea, whereas females presented with higher mean age, lower EDS scores, and less time in sleep apnea. The EDS score showed best correlation with duration of apnoea (r = 0.448; p < 0.01), peripheral oxygen saturation (SpO₂; r = -0.458; p < 0.01) and AHI (r = 0.484; p < 0.01). The mean body mass index (BMI) was 27.41±3.86 kg/m². Normal, Overweight, obese, and morbidly obese were observed in 20%, 61%, 18%, and 0.6% of cases, respectively. Severity of the disease best correlated with BMI (r = 0.421; p < 0.01). Conclusions: OSA is predominant in males (M/F 5:1), and obese population. Females diagnosed with OSA have higher mean age. However, EDS scores and time spent in sleep apnoea is lower in females. Higher BMI is associated with EDS, irrespective of gender.

Periodontitis is a progressive and inflammatory oral disease and results in the damage of the supporting tissues of teeth. Peroxiredoxin6 (PRDX6) is an antioxidant enzyme and has been identified as a regulator in redox balance. This study aimed to investigate whether PRDX6 could protect human gingival fibroblasts (HGFs) from lipopolysaccharide (LPS) induced inflammation and its mechanisms. Here, both inflamed and non-inflamed human gingival tissues were collected to assess the expression of PRDX6 and NRF2 by Immunohistochemistry and Western blotting. Furthermore, HGFs were stimulated with LPS, MJ33 (PRDX6 phospholipase A2 inhibitor), or ML385 (NRF2 inhibitor). The expression levels of inflammatory cytokines were measured by RT-qPCR and ELISA, and reactive oxygen species (ROS) was detected using DCFH-DA. PRDX6 was downregulated in inflamed gingival tissues. In HGFs, LPS induced inflammatory cytokines and ROS was upregulated in PRDX6 knockdown cells. Furthermore, co-treatment with MJ33 alleviated LPS-induced inflammatory cytokines and ROS, while inhibiting NRF2 upregulated those in HGFs. Therefore, this study provided a new mechanistic insight that PRDX6, regulated by the NRF2 signaling, alleviates LPS- induced periodontitis in human gingival fibroblasts.

As the PCIe 6.0 specification places higher requirements on signal integrity and transmission la-tency, it becomes especially important to improve signal transmission performance at the physical layer of the transceiver interface. Retimer circuit as a key component of high-speed serial interface, its delay and jitter size directly affect the overall performance of PCIe. For the conventional Retimer circuit with large latency and low jitter performance, this paper proposes a low latency and low jitter Retimer circuit based on CDR+PLL architecture for PCIe 6.0, using a jitter canceling filter circuit to eliminate the frequency difference between the retiming clock and data, reduce the retiming clock jitter, and improve the quality of Retimer output data; The data is sampled using the retiming clock and then output, avoiding the problem of large penetration latency of con-ventional Retimer circuits. The circuit is designed using CMOS 28nm process. Simulation results show that when 112Gbps PAM4 data is input to the Retimer circuit, the Retimer penetration la-tency is 27.3 ps, which is 83.5% lower than the conventional Retimer structure; the output data jitter is 741 fs, a 31.4% reduction compared to the conventional Retimer structure.

In order to study the effects of dietary folic acid (FA) supplementation on growth performance and immune status in weanling piglets, a single factorial randomized block design trial with 6 dietary FA levels at 0.35, 0.66, 2.19, 5.18, 7.51 or 10.81 mg/kg was conducted. A total of 108 crossbred (Landrace × Yorkshire) castrated weanling piglets (at 21 d of age) were allocated by body weight into 36 feeding cages (3 piglets/cage), which were allotted randomly into 6 dietary groups (6 cages/group). Piglets were fed ad libitum for 24 days. Blood samples were collected on the 24th day. The growth performance and the immune parameters were measured. Results showed that FA supplementation increased the serum FA level of weaned piglets (p < 0.01), and tended to increase the body weight (BW) at 45 d of age (p < 0.1) and the average daily gain (ADG) from 29 d to 45 d of age (p < 0.1). FA addition improved the feed efficiency (G/F) from 21 d to 45 d of age (p < 0.01), and with significant effects at 21 d to 45 d of age with FA 2.19 or 7.51 mg/kg (p < 0.05). Dietary FA at 0.66 or 2.19 mg/kg increased the serum CD3+CD8+ subset (p < 0.05), decreased the CD3+CD4+ / CD3+CD8+ ratio (p < 0.05); Moreover, FA addition increased the serum IFN-γ level (p < 0.05). In conclusion, the adequate dietary FA is necessary to improve the immunity and growth performance of weaned piglets at 21 d of age. The suitable dietary FA level for immune function from 21 d to 45 d of age was 0.66 mg/kg, while were 6.82 mg/kg from 21 d to 28 d of age and 5.42 mg/kg from 29 d to 45 d of age respectively for feed efficiency.

The spectra and global distributions of the X-ray emissions generated by the solar wind charge-exchange (SWCX) process in the terrestrial magnetosheath are investigated based on a global hybrid model and a global geocoronal hydrogen model. The solar wind O6+ ions which are the primary charge state for oxygen ions in solar wind are considered. The line emissivity of the charge-exchange born O5+ ions are calculated by Spectral Analysis System for Astrophysical and Lab oratory (SASAL). It is found that the emission lines from the O5+ ranges from 105.607 to 118.291 eV with the strong line at 107.047 eV. We then simulated the magnetosheath X-ray emission intensity distributions with a virtual camera at two positions of north pole and dusk at six stages during the passing of a perpendicular interplanetary shock combined with a tangential discontinuity structure through the Earth’s magnetosphere. During this process, the X-ray emission intensity increases with time, and the maximum value is 27.11 keV cm-2 s-1 sr-1 on the dayside, which is 4.5 times that before the solar wind structure reaches the Earth. A clear shock structure can be seen in the magnetosheath and moves earthward. The maximum emission intensity seen at dusk is always higher than that seen at north pole.

This research is aimed to investigate the effects of Lactoplantibacillus plantarum (L. plantarum) on growth performance, oxidation resistance, immunity, as well as cecal microbiota in broilers. This work classed three hundred and sixty 1-day-old broilers as three groups randomly, including control (CON, basal diet), antibiotic (ANT, 75 mg kg-1 chlortetracycline added into basal diet), or probiotic group (LP, 5×108 CFU kg-1 Lactoplantibacillus plantarum HJLP-1 contained within basal diet). Animal were then fed for 42 days, and each group consisted of 15 broilers for 8 replicates. Compared with CON, L. plantarum supplementation significantly improved the average weight daily gain (AWDG) (P < 0.05) while reducing feed-to-gain ratio over the entire supplemental period (P < 0.05). Birds fed L. plantarum had marked lower serum ammonia and xanthine oxidase levels (P < 0.05) than those in ANT and CON. Significant improvements (P < 0.05) of superoxide dismutase, catalase, serum IgM and IgY contents in broilers fed L. plantarum were also observed when compared those in CON and ANT groups. Both L. plantarum and antibiotics decreased the pro-inflammatory factor IL-1β level significantly (P < 0.05), while only L. plantarum promoted the anti-inflammatory factor IL-10 level dramatically in the serum (P < 0.05) compared with CON. The L. plantarum dramatically (P < 0.05) increased acetic acid and butyric acid concentrations in the cecal contents，when compared to those in CON and ANT. Among the differences revealed by 16S rRNA analysis, L. plantarum markedly improved the community richness of cecal microbiota. At the genus level, butyric acid-producing bacteria Ruminococcus and Lachnospiraceae were found in higher relative abundance in samples of L. plantarum treated birds. In conclusion, dietary L. plantarum supplementation promoted the growth and health of broilers, likely by inducing a shift in broiler gut microbiota toward short-chain fatty acid (SCFA)-producing bacteria. Therefore, L. plantarum has tremendous potential as an alternative for antibiotics in poultry breeding.

With the advancement of technology, signal modulation types are becoming increasingly diverse and complex. The phenomenon of signal time-frequency overlap during transmission poses significant challenges for the classification and recognition of mixed signals, including poor recognition capabilities and low generality. This paper presents a recognition model for fine-grained analysis of mixed signal characteristics, proposing a Geometry Coordinate attention mechanism and introducing a low-rank bilinear pooling module to more effectively extract signal features for classification. The model employs a residual neural network as its backbone architecture and utilizes the Geometry Coordinate attention mechanism for time-frequency weighted analysis based on information geometry theory. This analysis targets multiple-scale features within the architecture, producing time-frequency weighted features of the signal. These weighted features are further analyzed through a low-rank bilinear pooling module, combined with the backbone features, to achieve fine-grained feature fusion. This results in a fused feature vector for mixed signal classification. Experiments were conducted on a simulated dataset comprising 39,600 mixed signal time-frequency plots. The model was benchmarked against a baseline using a residual neural network. The experimental outcomes demonstrated an improvement of 9% in the exact match ratio and 5% in the Hamming score. These results indicate that the proposed model significantly enhances the recognition capability and generalizability of mixed signal classification.

This paper proposes a new approach for multi-focus images fusion based on Region Mosaicing on Contrast Pyramids (REMCP). A density-based region growing method is developed to construct a focused region mask for multi-focus images. The segmented focused region mask is decomposed into a mask pyramid, which is then used for supervised region mosaicking on a contrast pyramid. In this way, the focus measurement and the continuity of focused regions are incorporated and the pixel level pyramid fusion is improved at the region level. Objective and subjective experiments show that the proposed REMCP is more robust to noise than compared algorithms and can fully preserves the focus information of the multi-focus images meanwhile reducing distortions of the fused images.

Contrafreeloading (CFL) refers to animals' tendency to prefer obtaining food through effort rather than free access to food. Researchers have proposed various hypotheses to explain this intriguing phenomenon, but few studies have comprehensively analyzed its influencing factors. In this study, we observed the choice of alternative food containers in budgerigars to investigate their CFL tendencies and the effects of pre-training, food deprivation, and effort required on the CFL levels. The results show that, like most captive animals, budgerigars without food deprivation tend to choose challenging food containers. Additionally, the study finds that pre-trained budgerigars prefer to choose highly challenging food containers, while food-deprived budgerigars tend to choose Easy food containers. Moreover, budgerigars showed more selection time proportion on moderate challenging than high challenging food containers. In conclusion, budgerigars exhibit CFL tendencies, and pre-training enhances their CFL levels, while high challenge and deprivation of food decrease their contrafreeloading level. Studying animal contrafreeloading can help understand why animals choose to expend effort to obtain food rather than accessing it for free, and it also has implications for setting feeding environments to enhance the animal welfare of captive and domesticated animals.

As an outstanding information carrier, skyrmion is increasingly widely used in devices based on complex geometries. To achieve the skyrmion-based spintronic devices, a reasonable and feasible nanotrack is essential. In this paper, we conducted a study on the current-driven skyrmion movement in a circular-ring-shaped nanotrack. Our results suggest that the asymmetry of the inside and outside boundary of the circular ring changed the stable position of the skyrmion, causing it to move like the skyrmion Hall effect when driven by currents. Moreover, the asymmetric boundaries have advantages in enhancing or weakening the skyrmion Hall effect. Additionally, we also compared the skyrmion Hall effect from the asymmetric boundary of circular ring nanotracks with that from inhomogeneous DMI. It is found that the skyrmion Hall effect caused by the circular ring is significantly greater than that caused by the inhomogeneous DMI. These results contribute to our understanding of the skyrmion dynamics in confined geometries and offer an alternative method for controlling the skyrmion Hall effect of skyrmion-based devices.

Because rice is native to tropical and subtropical regions, it is generally more sensitive to cold stress compared to other cereals. Low temperature stress has become one of the most important conditions that affects the growth, development, and yield of rice. Plant NAC (NAM, ATAF1/2, and CUC) transcription factors are known to play significant regulatory roles in the stress response. In our research, we found that OsNAC050 (LOC_Os03g60080） is mainly expressed in leaves, and low temperature can further up-regulate its expression. OsNAC050 mutants created using CRISPR-Cas9 gene editing technology showed significantly enhanced tolerance to low temperature treatment. Detection of enzyme activities related to the redox pathway also showed that the mutants had stronger viability under low temperature stress. Comparative transcriptome analysis showed that photosynthesis and soluble sugar metabolism were significantly affected in the osnac050 mutant lines, suggesting that OsNAC050 may participate in the above molecular pathways in the response to low temperature stress. The results will enhance our understanding of molecular mechanisms underlying the responses to cold stress in rice and can provide new strategies for engineering cold-tolerance in high-yielding rice varieties.

The adapted Posner spatial cue-target paradigm was used to explore the relationship between exogenous temporal attention caused by rhythm and endogenous and exogenous spatial attention. The study was divided into two experiments. In Experiment 1, 33 participants used arrow cues to orient endogenous spatial attention and rhythm to orient exogenous temporal attention. In Experiment 2, with 29 participants, exogenous spatial attention was directed by highlighting the cue box. Exogenous temporal attention was directed by rhythm. Experiment 1 indicated that RTs were faster for attended targets than the unattended. The main effect of temporal attention was significant, with RTs being faster for synchrony and late compared to early. RTs were faster for late compared to synchrony. The main effect of stimulus repetition was significant, with faster RTs for targets when the rhythmic cue consisted of five compared to four. The interaction between spatial attention and temporal attention was not significant. Experiment 2 demonstrated that exogenous spatial attention only exhibited IOR under early four stimulus repetitions. The main effect of temporal attention was significant, with RTs being faster for synchrony and late compared to early. The main effect of stimulus repetition was significant, with faster RTs for targets when the rhythmic cue consisted of five compared to four. The interaction between spatial attention and temporal attention was significant. The results indicated that rhythmic temporal attention supported foreperiod effects. Exogenous temporal attention and endogenous spatial attention independently affect behavior, while exogenous temporal attention and exogenous spatial attention mutually influenced behavior.

Plant endophytic fungi and rhizosphere soil fungi are often reported as biocontrol agents against plant pathogens or with plant growth promotion potential. Four treatments were performed in field and greenhouse experiments where cucumber plants were inoculated with Trichoderma harzianum and Fusarium oxysporum in 2022. The roots, stems and leaves of cucumber plants and their rhizosphere soil were collected twice individually from the field and greenhouse for isolation of cucumber endophytic and rhizosphere soil fungi. All 74 genera and 1275 fungal strains were sequenced by rDNA ITS. The PDA media yielded the highest number of genera isolated from cucumber plants, rhizosphere soil and both compared to other media. There were no significant differences among the 4 media for the isolation of cucumber endophytic fungi. The best media for isolating fungi from roots and stems were MRBA and PDA, respectively. PDA and CZA had higher isolation efficiency for the rhizosphere soil fungi than MRBA. The 28 fungal genera had high isolation efficiency, and the endophytic Trichoderma strains were best isolated by MEA. It is suggested that PDA can be used as a basic medium, and different media can be considered for specific fungal genera.

Objectives: The purpose of this study is to determine the association between umbilical venous blood flow (UVBF) to placental pulsatility index (PPI) ratio and gestational age (GA) in women undergoing prenatal assessments and adverse pregnancy outcome (APO) screening Methods: Between January and December 2022, sonographic examinations were conducted to assess the fetal umbilical cord insertion site in singleton fetuses, and hemodynamic indices of the umbilical artery, umbilical vein, and uterine artery were computed. Through regression analysis, we derived the optimal regression equation to elucidate the UVBF/PPI ratio parameters based on GA. Results: Among 492 singleton fetuses between 21+0 and 40+6 weeks of gestation in the final study. The average fetal UVBF/PPI ratio was 180.45±119.32. Correlation analysis revealed a positive relationship between the UVBF/PPI ratio and GA(p = .000). Using regression analysis, the best-fit regression equation was the linear function model, which explains the value of UVBF/PPI ratio parameters based on GA. Lower UVBF/PPI ratio revealed a positive relationship in the low birth weight fetuses (p=0.021) and higher preterm delivery rate (p=0.034). Cerebroplacental ratio (CPR) showed a high correlation with the UVBF/PPI ratio (r=0.471, p=0.000). Conclusions: The findings of our analyses revealed that contribute to our understanding of fetal hemodynamics and highlight the potential of UVBF/PPI ratio as a predictive marker for adverse pregnancy outcomes, such as preterm birth, low birth weight, or potential fetal hypoxemia. It might be useful for prenatal counseling and clinical purposes.

Japanese encephalitis is a zoonotic disease caused by Japanese encephalitis virus (JEV). It is mainly epidemic in Asia with an estimated 69,000 cases occurring per year. However, no approved agents are available for the treatment of JEV infection, and existing vaccines cannot resist various types of JEV strains. Drug repurposing is a new concept for finding new indication of existing drugs, and recently, it has been used to discover new antiviral agents. Identifying host proteins involved in the progress of JEV infection and using these proteins as targets are the center of drug repurposing for JEV infection. In this study, based on the gene expression data of JEV infection and the phenome-wide association study (PheWAS) data, we identified 286 genes participating in the progress of JEV infection using the systems biology methods. The enrichment analysis of these genes suggested that the genes identified by our methods were predominantly related to viral infection pathways and immune response-related pathways. We found that bortezomib which can target these genes may have potential effect on the treatment of JEV infection. Subsequently, we evaluated the antiviral activity of bortezomib using the JEV-infected mice model. The results showed that bortezomib can lower JEV-induced lethality in mice, alleviate suffering in JEV-infected mice and reduce the damage in brains caused by JEV infection. This work provides a new method for the development of antiviral agents.

The interfacial mechanics and electrical properties of the SiC reinforced copper matrix composites were studied via the first principles method. The work of adhesion (Wad) and the interfacial energies were calculated to evaluate the stabilities of the SiC/Cu interfacial models. The carbon terminated (CT)-SiC/Cu interfaces were predicted more stable than those of the silicon terminated (ST)-SiC/Cu from the results of the Wad and interfacial energies. The interfacial electron properties of SiC/Cu were studied via the charge density distribution, charge density difference, electron localized functions and partial density of the state. The covalent C-Cu bonds were formed based on the results of the electron properties, which further explained the fact that the interfaces of the CT-SiC/Cu are stable than those of the ST-SiC/Cu. The interfacial mechanics of the SiC/Cu were investigated via the interfacial fracture toughness and ultimate tensile stress, and the results indicate that both CT- and ST-SiC/Cu interfaces are hard to fracture. The ultimate tensile stress of the CT-SiC/Cu is nearly 23GPa, which is smaller than those of the ST-SiC/Cu of 25 GPa. The strains corresponding to their ultimate tensile stresses of the CT- and ST-SiC/Cu are about 0.28 and 0.26, respectively. The higher strains of CT-SiC/Cu indicate their stronger plastic properties on the interfaces of the composites.

Rare study on quantitative relationship between energetic impact of debris flows on the intensity and duration of growth disturbances of tree rings was carried out, partly due to lack of feasible approaches and detailed field evidence. In this study, we firstly determine the age of a recent debris flow derived from historic landslide deposits at Qingyang mountain (QYM) on the northeastern Tibet plateau by dendrogeomorphic technique. We acquired the quantitative data of annual widths of tree rings in history and confirmed the influence of debris flow rather than other factors (e.g. climatic event and inset outbreaking) in disturbing the growth of tree rings in a specific year. Using the approach, we determined the age of the debris flow at QYM occurred in 1982, which was speculated to be triggered by high monthly precipitation of July in 1982. Subsequently, based on the boundaries of historic debris flow identified on remote sensing images before and after 1982 and depth-integrated continuum model, we reconstructed the process of 1982-debris flow and obtained the kinematic energy of debris flow impacting on the sampled trees. Based on the study, we observed that two growth disturbance patterns of tree rings influenced by the reconstructed 1982-debris flow were revealed including growth suppression and asymmetric growth. A raw logarithm relationship between duration (i.e. lasting time for the disturbed tree rings to recover the initial width) and intensity of growth disturbances (i.e. growth suppression ratio of disturbed tree rings) was obtained. We concluded that there is a negative exponential relationship between simulated kinematic energy of debris flow impacting on the disturbed trees and time to recover the initial width of corresponding tree rings.

During choriogenesis in insects, chorion (eggshell) is formed by surrounding follicular epithelial cells in ovarioles. However, the regulatory endocrine factor(s) activating choriogenesis and the chemical components on eggshell deserve further exploration. In two representative Coleopterans, a Coccinellid Henosepilachna vigintioctopunctata and a Chrysomelid Leptinotarsa decemlineata, genes encoding the 20-hydroxyecdysone (20E) receptor heterodimer, ecdysone receptor (EcR) and ultraspiracle (USP), and two chitin biosynthesis enzymes UDP-N-acetylglucosamine pyrophosphorylase (UAP) and chitin synthase (ChS1), were highly expressed in ovaries of the young females. RNA interference (RNAi)-aided knockdown of either HvEcR or Hvusp in H. vigintioctopunctata inhibited oviposition, suppressed the expression of HvChS1, and lessened the positive signal of Calcofluor staining on the chorions, which suggests the reduction of a chitin-like substance (CLS) deposited on eggshells. Similarly, RNAi of LdEcR or Ldusp in L. decemlineata constrained oviposition, decreased the expression of LdUAP1 and LdChS1, and declined CLS contents in the resultant ovaries. Knockdown of LdUAP1 or LdChS1 caused similar defective phenotypes, i.e., reduced oviposition and CLS contents in the L. decemlineata ovaries. These results, for the first time, indicate that 20E signaling activates choriogenesis in two Coleopteran species. Moreover, our findings propose the deposition of a CLS on the chorions.

This general review assesses the impact of physical exercise on oxidative and nitrosative stress and the counteractive role of antioxidants, drawing from a systematic literature search up to March 2024 in databases like PubMed and Web of Science. The review highlights studies on the effect of exercise on the production of reactive oxygen species (ROS) and reactive nitrogen species (RNS) and antioxidant responses in both human and animal models based on rigorous inclusion and exclusion criteria. Due to the variety of exercise types and participants' characteristics, a narrative synthesis approach was adopted. The findings indicate that moderate exercise boosts antioxidant defenses, known as hormesis, whereas excessive physical activity may increase oxidative and nitrosative damage. The review also explores the complex effects of antioxidant supplementation, revealing that while natural dietary antioxidants support health, high-dose supplements could potentially hinder positive adaptations to exercise. Recommendations for athletes and the general active population highlight the importance of balancing exercise and dietary intake to optimize health benefits. The review concludes with a call for more detailed research on tailored exercise and nutrition plans to dissect these intricate relationships further.

Five new perylenequinone derivatives, altertoxins VIII-XII (1-5), as well as one known compound cladosporol I (6), were isolated from the fermentation broth of Cladosporium sp. KFD33 from a blood cockle from Haikou Bay, China. Their structures were determined based on spectroscopic methods and ECD spectra analysis along with quantum ECD calculations. Compounds 1-6 exhibited quorum sensing inhibitory activities against Chromobacterium violaceum CV026 with MIC values of 30, 30, 20, 30, 20 and 30 μg/well, respectively.

Semi-continuous data are very common in the social science and economics. In this paper, a Bayesian variable selection procedure is developed to assess the influence of exogenous factors including observed and unobserved on the semi-continuous data. Our formulation is based on the two-part latent variable model with polytomous response. We consider two schemes for the penalties of regression coefficients and factor loadings: the Bayesian spike and slab bimodal prior and the Bayesian lasso prior. Within the Bayesian framework, we implement Markov Chains Monte Carlo sampling method to conduct posterior inference. To facilitate posterior sampling, we recast the logistic model in part one as the norm-like mixture model. Gibbs sampler is designed to draw observations from the posterior. Our empirical results show that with suitable hyper-parameters, the spike and slab bimodal method slightly outperforms the Bayesian lasso in the current analysis. Finally, a real example related to the China household finance survey is analyzed to illustrate the application of the methodology.. .

The pathogenicity of grapevine geminivirus A (GGVA), a recently identified DNA virus, to grapevine plants remains largely unclear. Here, we report a new GGVA isolate (named GGVAQN) obtained from grapevine ‘Queen Nina’ plants with severe disease symptoms; the infectious clone of GGVAQN (pXT-GGVAQN) was also constructed. Infection assays indicated that Nicotiana benthamiana plants inoculated with GGVAQN display upward leaf curling and chlorotic mottling symptoms. Direct injection of Agrobacterium tumefaciens cells carrying pXT-GGVAQN into roots of in vitro-grown ‘Red Globe’ grape plantlets by syringe led to systemic infection with GGVAQN, and the plants exhibited chlorotic mottling symptoms on their upper leaves, and downward curling, interveinal yellowing, and leaf-margin necrosis symptoms on their lower leaves. Our results provide insights into the pathogenicity of GGVA, and a simple and efficient inoculation method to deliver infectious viral clones to woody perennial plants.

Watermelon fusarium wilt caused by Fusarium oxysporum f.sp. niveum (FON) is a destructive soil-borne disease throughout the world leading to serious economic losses and limit watermelon production. Cuminic acid, extracted from the seed of Cuminum cyminum L., belongs to benzoic acid analogues. In this study, the median effective concentration (EC₅₀) values for cuminic acid in inhibiting mycelial growth of FON was 22.53μg/mL. After treatment with cuminic acid, mycelial morphology was seriously influenced; cell membrane permeability and glycerol content were increased markedly, but pigment and mycotoxin (mainly fusaric acid) were significantly decreased. Synthesis genes of bikaverin and fusaric acid both were down regulated compared with the control confirmed by quantitative RT-PCR. In greenhouse experiments, cuminic acid at all concentrations displayed significant bioactivities against FON. Importantly, significant enhancement of activities of SOD, POD, CAT and decrease of MDA content after cuminic acid treatment in watermelon leaves were observed in vivo. These indicated that cuminic acid not only showed high antifungal activity, but also could enhance the self-defense system of the host plant. Above all, cuminic acid showed the potential as a biofungicide to control FON.

The calculation of the exact value of the square root of 2 is requested. In order to obtain its infinite value, A new concept is proposed where the accumulations of the infinitely many of finity is indicated by the change in direction which means that there is a jump from finity to infinity .The meaningless for an infinite number with a decimal point is indicated by this jump because any decimal number only have meanings within a finite range values and there is only an infinite integer quantity that can not be operated by algorithms like operations of multiplication，division,addition, and subtraction . The final result of the change in direction is two quantity where the second quantity and the first quantity extend in parallel line and never intersect and the second quantity represent the size of the first quantity. The first quantity is the infinitely great that can't be talked about anything outside of it and can compress any quantities outside of it to nothing and it is the exact value of the square root of 2 .

Abstract Although we know something about single cell neuromuscular junction, It is still mysterious how multiple skeletal muscle cells coordinate to complete the intricate spatial curve movement. Here I propose a hypothesis that skeletal muscle cell populations with action potentials are alligned according to a curved manifolds on space(a curved shape on space) and the skeletal muscle also moves according to this corresponding shape(manifolds) when an specific motor nerve impulses are transmitted. the action potential of motor nerve fibers has the characteristics of time curve manifold and this time manifold curve of motor nerve fibers come from visual cortex in which a spatial geometric manifolds are formed within the synaptic connection of neurons. This spatial geometric manifolds of the synaptic connection of neurons orginate from spatial geometric manifolds in outside nature that are transmitted to brain through the cone cells and ganglion cells of the retina.Further,the essence of life is that life is an object that can move autonomously and the essence of life's autonomous movement is the movement of proteins. theoretically, due to the infinite diversity of geometric manifold shapes in nature, the arrangement and combination of 20 amino acids should have infinite diversity, and the geometric manifold formed by protein three-dimensional spatial structure should also have infinite diversity.

An approximate calculation of the spatial characteristics on finite range is required, so one quantitative continuum represents the accumulation of infinite great quantities is artificially divided it into smaller and camparable parts in which calculus operation can be applied .This operation is defined as Theorem 1 in which infinity is not involved, there is a camparable finity is constantly (forever) approaching and not reaching infinity, and only staying within a finite range. Theorem 1 can exist in this paper as a new mathematical basis for physics. Because the essence of all physical quantities is size comparison, and the size comparison relation of matter can only be space/time, so relation formula space/time is the only expression of the concept of matter, all physical quantities are applicable to this expression, each different physical quantity is a multi-dimensional representation of this expression. A new mass energy formula is aslo derived from this paper.

Abstract Unlike accelerated motion or curvalinear motion,a nonlinear motion state(non-inertial system) can be described by differential equations or the other algebric equations in axiom 2, the accelerated motion in axiom 3 can be considered to be described by using the equation of the linear and curvilinear process of the continuum extending to infinitely distance.Further, this linear and curvilinear process of the continuum is a quantitative continuum in essence as a unity of infinitely quantities and infinitely dimensions at infinite distance (infinity) relative to all orientations in which we exist. These indicates that an accelerated motion accumulates continuously started from a finite quantities, leaping to transit from finite to infinite quantities by an infinitely great accelerating force.

To provide carbon steel a long corrosion protection effect in NaCl solution with various pH, a pH-controlled intelligent inhibitor based on poly-acrylamide (PAM) and oleate imidazoline (OIM) was synthesized. SEM, FT-IR and TGA results indicating the OIM inhibitor was successfully loaded into PAM hydrogel with a very high content (39.64 wt%). The OIM release behavior from hydrogel structure have two stages, quickly release and sustained release. The pH of solution could affect the initial release kinetics of OIM inhibitor and the diffusion path in hydrogel structure. Weight loss measurement of L80 steel in different pH solution with OIM@PAM proved the inhibitor responsive release mechanism and an-ti-corrosion performance. The inhibition efficiency of OIM@PAM can maintain over 80% after long term immersion in harsh corrosive environment (pH 3), which is much higher than the inhibition efficiency of inhibitor in moderate corrosive solution.

We estimated the daily intakes of chlorpyrifos and cypermethrin via ingestion of indoor dust and outdoor soils using the Stochastic Human Exposure and Dose Simulation Model on a probabilistic approach for Taiwan’s homes. Variable information for the daily intake estimation, such as concentration, ingestion rate, body weight, was adopted from previous studies. Monte Carlo simulation was performed with 1,000,000 iterations to simulate a single daily intake, which was shown in terms of percentage of the Acceptable Daily Intake (ADI) of either insecticide. The daily intakes were minimal with a 99% probability; at 99.9th percentile, however, the total intakes leaped to 13.1% and 20.0% of the respective ADIs of chlorpyrifos and cypermethrin. The sensitivity analysis indicated that concentration was the most determinant variable. Compared to the data of daily intakes via dietary ingestion of vegetables derived from a previous study, the estimated intakes by this study were considerable at the highest percentile, which referred to insecticide residues few days after insecticide application. Consequently, the non-dietary ingestion exposure to either insecticide was negligible in most cases; nevertheless, for those with indoor insecticide applications, the daily intakes for young children could be of concern. Frequently home cleaning is recommended to reduce the exposure.

Aflatoxin biosynthesis is correlated with oxidative stress and is proposed to function as a secondary defense mechanism to redundant intracellular reactive oxygen species (ROS). We find that the antioxidant gallic acid inhibits aflatoxin formation and growth in A. flavus in a dose-dependent manner. Global expression analysis (RNA-Seq) of gallic acid treated A. flavus showed that 0.8% (w/v) gallic acid revealed two possible routes of aflatoxin inhibition. Gallic acid significantly inhibited the expression of farB, encoding a transcription factor that participates in peroxisomal fatty acid β oxidation, a fundamental contributor to aflatoxin production. Secondly, the carbon repression regulator encoding gene creA was significantly down regulated by gallic acid treatment. CreA is necessary for aflatoxin synthesis and aflatoxin biosynthesis genes were significantly downregulated in DcreA mutants. In addition, the results of antioxidant enzyme activities and the lipid oxidation levels coupled with RNA-Seq data of antioxidant genes indicated that gallic acid may reduce oxidative stress through the glutathione- and thioredoxin-dependent systems in A. flavus.

Bearings are widely used in various types of electrical machinery and equipment. As their core components, failures will often cause serious consequences . At present, most methods of parameter adjustment are still manual adjustment of parameters. This adjustment method is susceptible to prior knowledge and easy to fall into the local optimal solution, failing to obtain the global optimal solution and requires a lot of resources.Therefore, this paper proposes a new method of bearing fault diagnosis based on wavelet packet transform and convolutional neural network optimized by simulated annealing algorithm.The experimental results show that the method proposed in this paper has a more accurate effect in feature extraction and fault classification compared with traditional bearing fault diagnosis methods. At the same time, compared with the traditional artificial neural network parameter adjustment, this paper introduces the simulated annealing algorithm to automatically adjust the parameters of the neural network, thereby obtaining an adaptive bearing fault diagnosis method. To verify the effectiveness of the method, the Case Western Reserve University bearing database was used for testing, and the traditional intelligent bearing fault diagnosis method was compared. The results show that the method proposed in this paper has good results in bearing fault diagnosis. Provides a new way of thinking in the field of bearing fault diagnosis in parameter adjustment and fault classification algorithms

Current effort with light field displays is mainly concentrated on the widest possible viewing angle, while a single viewer only needs to view the display in a specific viewing direction. To make light field display a practical practice, a super multi-view light field display is proposed to compress the information in the viewing zone of a single user by reducing the redundant viewpoints. A quasi-directional backlight is proposed and a lenticular lens array is applied to achieve the restricted viewing zone. Eye-tracking technique is applied to extend the viewing area. Experimental results show that the proposed scheme can present vivid 3D scene with smooth motion parallax. Only 16.7% conventional light field display data are required to achieve 3D display. Furthermore, an illumination power of 3.5 watt is sufficient to lighten a 31.5-inch light field display，which takes up 1.5% of the illumination power required for planar display of similar configuration.

Fully mechanized mining face production involves complex geological conditions; mining pressure; gas, water, fire and other mining environments. The working face needs a shearer, hydraulic support, a scraper conveyor and other equipment for coordination. The deep integration of intelligent technology with factors such as "humans, machines, the environment, and management" in the workplace is the core content of intelligent coal mines. This paper puts forward an advanced framework for coal mining robot technology systems, including single robots, robotized equipment, robot clusters and unmanned systems. The framework clarifies the common key technologies of coal mining robot research and development and cross-integration with new technologies such as 5G, the industrial internet, big data, artificial intelligence, and digital twins to improve the autonomous and intelligent application of coal mining robots. By establishing a scientific and complete standard system for coal mining robots, we aim to achieve customized research and development and standardized production of various types of robots. A specific analysis was conducted on the research progress of common key technologies such as explosion-proof design, mechanical system innovation, power drive, intelligent sensing, positioning and navigation, and underground communication of coal mining robots. The current research and application status of various types of coal mining robots in China are summarized. A new direction for future coal mine robot research and development is proposed. Moreover, robotic mining systems should be promoted to enhance the overall intelligence level and mining efficiency of mining equipment. To develop human‒machine environment-integrated robots to improve the autonomy and collaboration level of coal mining robots. The digital twinning of the entire mine robot system should be accelerated, the normalized operation level of coal mine robots should be improved, research on coal mining robots, support robots, and transportation robots should be carried out, intelligence should be achieved in fully mechanized mining faces, and equipment support for fewer and unmanned fully mechanized mining faces should be provided. The practical process of implementing coal mining robotization has been summarized, and the technical and engineering feasibility of the coal mining machine population has been verified.

Fiber aggregation in nanocomposites has an important effect on the macroscopic electrical performance. To quantitatively evaluate its effect, an index to characterize the degree of aggregation is imperative, and ideally it should have three features simultaneously, i.e., single-parametric, dimensionless and physically meaningful, applicable to different aggregation topologies, and one-to-one corresponding to material electrical properties. To this end, a new aggregation degree is proposed, which is defined as the average increased number of fibers that connect with each one when fibers aggregate from a uniformly distributed state. This index is applicable to different aggregation topologies from lump-like aggregating clusters to network-like aggregating clusters. This index is proven to only depend on the local features of aggregating clusters, and can be concisely expressed by the characteristic parameters of local structure, via geometric probability analysis and numerical validations. Further, a one-to-one linear relation between the aggregation degree and percolation threshold is established by Monte Carlo simulations, which is independent of the distribution law of the fibers. This work provides a guide to the property characterization, performance prediction and material design of nanocomposites, and also gives a physical insight into the understanding of systems with similar non-uniform distributions.

A fast calculation method for the full parallax high-resolution hologram is proposed based on the elemental light field image (EI) rendering. A 3D object located near the holographic plane is firstly rendered as multiple EIs with a pinhole array. Each EI is interpolated and multiplied by a divergent sphere wave and interfered with a reference wave to form a hogel. Parallel acceleration is used to calculate the high-resolution hologram because calculation of each hogel is independent. A high-resolution hologram with the resolution of 20,0000×20,0000 pixels is calculated only within 8 minutes. Full parallax high-resolution 3D displays are realized by optical reconstructions.

In wireless sensor networks (WSNs), each sensor node can estimate the global parameter from the local data in distributed manner. This paper proposed a robust diffusion estimation algorithm based on minimum error entropy criterion with self-adjusting step-size, which are referred to as diffusion MEE-SAS (DMEE-SAS) algorithm. The DMEE-SAS algorithm has fast speed of convergence and is robust against non-Gaussian noise in the measurements. The detailed performance analysis of the DMEE-SAS algorithm is performed. By combining the DMEE-SAS with diffusion minimum error entropy (DMEE) algorithms, an Improving DMEE-SAS algorithm is proposed, in non-stationary environment where tracking is very important. The Improving DMEE-SAS algorithm can avoid insensitivity of the DMEE-SAS algorithm due to the small effective step-size near the optimal estimator, and obtain a fast convergence speed. Numerical simulations are given to verify the effectiveness and advantages of these proposed algorithms.

Permeability has an important effect on drug absorption. In this study, the effect of different concentrations of sodium sulfobutyl ether-β-cyclodextrin (SBE-β-CD) on the absorption of ranitidine was investigated to examine the mechanism of permeability changes. The results of parallel artificial membrane permeability assay (PAMPA) showed that increasing the concentration of sodium sulfobutyl ether-β-cyclodextrin, 0, 0.12% (w/v), 0.36% (w/v) and 3.6% (w/v), respectively, the apparent permeability coefficient of ranitidine decreased to 4.62×10-5 , 4.5×10-5 , 3.61×10-5 and 1.08×10-5 in Caco-2 cells, respectively. The same results were obtained from oral pharmacokinetic study in rats; Further studies indicated that SBE-β-CD significantly increased the zeta potential of ranitidine. SBE-β-CD interacted with ranitidine charges to form a complex that reduced ranitidine permeability, and SBE-β-CD should be chosen with caution for drugs with poor permeability.

In this study, we resequenced the mitogenomes of P. megacephalus from different regions using a “primer bridging” approach with Sanger sequencing technologies. The mitogenome of this species was found to contain two copies of the ND5 genes and three copies of the control regions. Furthermore, multiple tandem repeats were identified in the control regions. Notably, we observed that there was no correlation between the distribution of species and their genetic distance. However, our research revealed the discovery of the “missing” ATP8 gene in P. megacephalus as well as three other previously published Polypedates, as a result of manual data curation. Using the mitogenome, gene expression analysis was performed via RT-qPCR of liver samples and determined that COIII, ND2, ND4, and ND6 were reduced to 0.64±0.24, 0.55±0.34, 0.44±0.21 and 0.65±0.17 under the low-temperature stress (8℃), respectively, as compared with controls (P<0.05). Remarkably, the transcript of long non-coding RNA (LncRNA) between positions 8029 and 8612 decreased significantly with exposure to low-temperature stress (8℃). Antisense ND6 gene expression showed a downward trend but this was not significant. These results reveal that modulations of protein-coding mitogenomes genes and lncRNAs of P. megacephalus play a crucial part in the molecular response to cold stress.

In tobacco plants, symbiont endophytic fungi are widely distributed in all tissues where they play important roles. It is therefore important to determine the species distribution and characteristics of endophytic fungi in tobacco. Here, two parasitic fungi Leptosphaerulina chartarum and Curvularia trifolii were isolated and identified from normal tobacco tissue. We sequenced the mitogenomes of these two species and analysed their features, gene content, and evolutionary histories. The L. chartarum and C. trifolii mitochondrial genomes were 68,926 bp and 59,100 bp long circular molecules with average GC contents of 28.60% and 29.31%, respectively. The L. chartarum mitogenome contained 36 protein coding genes, 26 tRNA genes, and 2 rRNA genes (rrnL and rrnS), which were located on both strands. The C. trifolii mitogenome contained 26 protein coding genes, 29 tRNA genes, and 2 rRNA genes (rrnL and rrnS). The L. chartarum 26 tRNAs ranged from 70 bp to 84 bp in length, whereas the 29 tRNAs in C. trifolii ranged from 71 bp to 85 bp. L. chartarum and C. trifolii mtDNAs had an identical mitochondrial gene order and orientation and were phylogenetically identified as sisters. These data therefore provide an understanding of the gene content and evolutionary history of species within Pleosporales.

We analyze a time-delayed SIQR model that considers the transportation-related infections and entry-exit screening. This model aims to determine the measures for preventing and controlling major emergent infectious diseases and the associated costs. We calculate the basic reproduction number (R0), apply the linearization method, and construct an appropriate Lyapunov function to determine the stability of the disease-free equilibrium in the local and global. We collect COVID-19 infection data from two regions in the United States in 2020 for data fitting, obtain a set of optimal parameter values, and show that the model is suitable for simulating the outbreak and spread of emerging infectious diseases. We find that transportation-related infections increase the basic reproduction number, enhancing the impact on disease spread. Entry-exit screening effectively suppress the spread of disease by reducing the basic reproduction number. Furthermore, we investigate the influence of the incubation period on disease and find that a shorter incubation period results in a shorter duration but a larger scale of infection, and the peaks are reduced. We conduct a sensitivity analysis of the R0 and propose three measures to prevent the spread of new infectious diseases based on the most sensitive parameters: wearing masks, implementing urban closures, and administering medication to sick but not yet hospitalized patients promptly. In the case of COVID-19, we use Pontryagin’s minimum principle to get time-varying control measures to control the spread of the outbreak. Optimal control effectively controls the development and deterioration of the disease. Finally, several control measures are compared through cost-effectiveness analysis, and the results show that wearing masks is the most cost-effective measure. Our study provides some practical guidance for controlling the spread of major emerging infectious diseases.

This paper presents an efficient topology optimization approach considering fail-safe requirements in the framework of the solid isotropic material with penalization method. Existing methods either are computationally extremely expensive or do not consider fail-safe requirements in the optimization. The current approach not only obtains the fail-safe optimization structure, but also significantly improves the computational efficiency of fail-safe topology optimization. In this method, the worst-case compliance is considered to minimize as the optimization objective, using the Kreisselmeier–Steinhauser function to approximate the non-differentiable max-operator. The sensitivity is derived by the adjoint method, and a general fail-safe optimality criteria method is developed to update design variables. The damage scenarios greatly reduces in the process of failsafe strategy optimization by employing the density-based filter method. Finally, the effectiveness and computational efficiency of this method for fail-safe optimization is verified by several numerical examples.

Previous camera self-calibration methods have exhibited certain notable shortcomings. On one hand, they either exclusively emphasized scene cues or solely focused on vehicle-related cues, resulting in a lack of adaptability to diverse scenarios and a limited number of effective features. Furthermore, these methods either solely utilized geometric features within traffic scenes or exclusively extracted semantic information, failing to comprehensively consider both aspects. This limited the comprehensive feature extraction from scenes, ultimately leading to a decrease in calibration accuracy. Additionally, conventional vanishing point-based self-calibration methods often required the design of additional edge-background models and manual parameter tuning, thereby increasing operational complexity and the potential for errors. Given these observed limitations, and in order to address these challenges, we propose an innovative roadside camera self-calibration model based on the Transformer architecture. This model possesses a unique capability to simultaneously learn scene features and vehicle features within traffic scenarios while considering both geometric and semantic information. Through this approach, our model can overcome the constraints of prior methods, enhancing calibration accuracy and robustness while reducing operational complexity and the potential for errors. Our method outperforms existing approaches on both real-world dataset scenarios and publicly available datasets, demonstrating the effectiveness of our approach.

In swarm-robotics foraging, the purpose of task allocation is to adjust the number of active foraging robots dynamically based on the task demands and changing environment. It is a difficult challenge to generate self-organized foraging behavior in which each robot can adapt to environmental changes. To complete the foraging task efficiently, this paper presents a novel self-organized task allocation strategy known as the dynamic response threshold model (DRTM). To adjust the behavior of the active foraging robots, the proposed DRTM newly introduces the traffic flow density, which can be used to evaluate the robot density. First, the traffic flow density and the amount of obstacle avoidance are used to adjust the threshold which determines the tendency of a robot to respond to a stimulus in the environment. Then, each individual robot uses the threshold and external stimulus to calculate the foraging probability that determines whether or not to go foraging. Simulation and physical experiments are carried out to evaluate the performance of the proposed method. The experimental results show that the DRTM is superior to and more efficient than the adaptive response threshold model (ARTM) in swarm foraging.

Chaphamaparvovirus (ChPV) is an ancient virus that has been detected in a variety of hosts. In this study, based on the phylogenetic analysis and the adaptability of ChPV to multiple hosts, we evaluated the potential of feline (FeChPV) and canine ChPV (CaChPV) for cross-species transmis-sion. Phylogenetic analysis showed that FeChPV and CaChPV were closely related. Notably, two strains of ChPVs isolated from domestic cats and 2 from dogs clustered together with CaChPVs and FeChPVs, respectively, suggesting the stringent boundaries between canine and feline ChPV may be broken. Further analysis revealed that CaChPV and FeChPV were more adapted to dogs than to cats, strongly suggesting the possibility of unidirectional or bidirectional transmission be-tween dogs and cats. Mutation analysis identified several shared mutations in cross-species-transmissible strains that were not located within immune epitopes. Furthermore, the VP struc-tures of FeChPV and CaChPV exhibited a high degree of similarity across both cross-species-transmissible and non-cross-species-transmissible strains. However, definitive experimental evi-dence is lacking, and its capacity for cross-species transmission should be approached with cau-tion and elucidated in further studies.

It is very difficult to accurately divide farmland and woodland in Gaofen 2 (GF-2) remote sensing image, because their single plant coverage is very small, and their spectra are very similar. The ratio of spatial resolution and one plant’s coverage area must be fully taken into account when designing the Convolutional Neural Network structure for extracting them from GF-2 image. We establish a Convolutional Encode Neural Networks model (CENN), The first layer has two sets of convolution kernels to learn the characteristics of farmland and woodland respectively, while the second layer is the encoder to encode the characteristics by transfer function, which can map the results to the corresponding category number. In the training stage, samples of farmland, woodland, and other categories are categorically used to train CENN, as soon as training is accomplished, CENN would acquire enough ability to accurately extract farmland and woodland from remote sensing images. The final extraction result is obtained by implementing per-pixel segmentation of images used to train the CENN. CENN is compared and analyzed with others such as Deep Belief Network (DBN), Full Convolutional Network (FCN), Deeplab Model. The results of experiments show that CENN can more accurately mine the characteristics of farmland and woodland, and it achieves its goal of extracting farmland and woodland with high precision from GF-2 images.

The goal of this lab is to look at how the characteristics of cementitious materials are affected by bending loads combined with dry and wet cycles of sulfate. In this paper, three sets of specimens with different water–cement ratios were designed. This study applied 20% and 40% of the ultimate bending load as a continuous bending load to the cementitious material specimens for a sulfate erosion test. It was discovered that the specimens' porosity, flexural strength, and compressive strength all tended to improve initially before declining as the cementitious material was degraded in the sulfate solution aged. The flexural strength of the cementitious materials declined as the bending load increased, and their internal sulfate ion concentration rose. A transport model of sulfate ions in cementitious materials under the coupling effect of bending load and sulfate erosion was created by combining the improved version of Fick’s second law and chemical reaction kinetics. The simulation results show that the ion transport properties of sulfate ions in cementitious materials are in accordance with the experimental laws. These research results formed the basis of the unified standards for the coupling of load dry and wet cycle systems, as well as evaluating the durability of cementitious materials under corrosive environments.

Enveloped viruses represent a significant category of pathogens that cause serious diseases in animals. These viruses express envelope glycoproteins that are singularly important during infection of host cells by mediating fusion between the viral envelope and host cell membranes. Despite low homology at protein levels, three classes of viral fusion proteins have, as of yet, been identified based on structural similarities. Their incorporation into viral particles is dependent upon their proper sub-cellular localization after being expressed and folded properly in the endoplasmic reticulum (ER). However, viral protein expression can cause stress in the ER, and host cells respond to alleviate the ER stress in the form of the unfolded protein response (UPR); the effects of which have been observed potentiating or inhibiting viral infection. One important arm of UPR is to elevate the capacity of the ER-associated protein degradation (ERAD) pathway, which is comprised of host quality control machinery that ensures proper protein folding. In this review, we provide relevant details regarding viral envelope glycoproteins, UPR, ERAD, and their interactions in host cells.

The basic idea is to expand the completed zeta function $\xi(s)$ in MacLaurin series (infinite polynomial), which can be further expressed as infinite product (Hadamard product) by conjugate complex roots. Finally, the functional equation $\xi(s)=\xi(1-s)$ leads to $(s-\alpha_i)^2 = (1-s-\alpha_i)^2, i \in \mathbb{N}$ with solution $\alpha_i= \frac{1}{2}, i \in \mathbb{N}$, where $\alpha_i$ are the real parts of the zeros of $\xi(s)$, i.e., $s_i =\alpha_i\pm j\beta_i, i\in \mathbb{N}$. Therefore, a proof of the Riemann Hypothesis is achieved.

With the proliferation and development of social media platforms, social media data has become an important source for acquiring spatio-temporal information on various urban events. Providing accurate spatio-temporal information for events contributes to enhancing the capabilities of urban management and emergency response. However, existing research on mining spatio-temporal information of events often focuses solely on textual content, neglecting data from other modalities such as images and videos. Therefore, this study proposes an innovative spatio-temporal information extraction method for multi-modal social media data (MIST-SMMD), which extracts the spatio-temporal information of events from multi-modal data on Weibo at coarse and fine-grained hierarchical levels, serving as a beneficial supplement to existing urban event monitoring methods. This paper takes the "July 20th Zhengzhou Heavy Rainfall" incident as an example, to evaluate and analyze the effectiveness of the proposed method. The results indicate that in the coarse-grained spatial information extraction using only textual data, our method achieves a Spatial Precision of 87.54% within a 60m range, and reaches 100% Spatial Precision for ranges beyond 200m. For fine-grained spatial information extraction, the introduction of other modal data such as images and videos results in a significant improvement in Spatial Error. These results demonstrate the ability of the MIST-SMMD method to extract spatio-temporal information from urban events at both coarse and fine levels, and confirms the significant advantages of multi-modal data in enhancing the precision of spatial information extraction.

During Sep. 2011, forty-four Leymus chinensis culms with stroma development were collected from Inner Mongolia. Stromata surrounded the flag leaf sheathes, white, at the final stage of development. Perithecium but not asci were observed under microscope. Nine epichloid endophyte strains were obtained from Tongliao subdivision, and sixteen from Horqin. Morphological and phylogenetic properties of these strains were investigated. Morphological properties of these strains were similar among these 27 strains. Colonies could grow to 28.5~41.1 mm/21d at 25℃; phialides 24.1~26.4 μm long, 2.1~2.5 μm at base, tapering to less than 1.0 μm at tip; conidia reniform to elliptical, 4.7~5.5×2.8~3.5 μm, indicating typical properties of Epichloë endophytes. Based on the sequences of tefA and tubB gene fragments, strains isolated from Inner Mongolia formed a distinct subclade in E. bromolica/ E. yangzii clade, with a bootstrap value of 66% and 64% respectively. Considering morphological and phylogenetic properties, we tend to determine strains isolated from Leymus chinensis as a new taxon. The detailed taxonomic position of this taxon needs further investigations on hybridization or genomic sequence.

Lactobacillus plantarum has been observed to play a crucial role in shaping the sensory properties of chili sauce. However, the specific taste-active metabolites responsible for the desirable flavor profile of chili sauce remain inadequately characterized. This study employed a combination of metabolomics and web-based computational tools analysis to investigate the dynamic changes in taste-active metabolites during chili sauce fermentation. Initially, metabolites were rapidly annotated using a feature-based molecular network, leading to the tentative annotation of 206 metabolites, of which a significant proportion had not been previously reported. Subsequently, the VirtualTaste tool identified dihydrosphingosine, lactic acid, isoleucine, phytosphingosine, and gluconic acid as potential taste markers for quality control. Finally, pathway enrichment analysis revealed that these components were primarily associated with amino acid tRNA, phenylalanine, tyrosine, and tryptophan biosynthesis, as well as sphingolipid metabolism. This study provides valuable insights into the mechanisms underlying the formation of the distinctive flavor of chili sauce.

Resection of malignant lesions in the oral and maxillofacial area causes functional and morphological defects. To recover from these defects, reconstruction surgery is needed such as a primary closure or a flap. There are advantages and disadvantages to the method of using the primary closure and the flap, and the choice of procedure is entirely up to a surgeon. The purpose of this study is to evaluate availability of primary closure in patients. For 10 years from January 2010 to May 2020, patients who recovered using flaps after removing malignant lesions from the oral cavity and those who closed the lesion using primary closure were investigated. The investigation was conducted by searching the database of the hospital. There were 85 patients who removed malignant lesions in the oral and maxillofacial area, and among them 16 patients closed the soft tissue defects using primary closure. Operation time, histologic types, stages, wound status, and period of hospitalization according to the patients' medical records were investigated retrospectively. Between the staging and the primary closure, statistically significant differences were observed between stage I and stage II patients in 13 patients using the primary closure. (P=0.046). Statistically significant differences were identified between operation time and primary closure, with an average of 4.02 hours (P=0.015). The average period of hospitality for patients who underwent primary closure was 13.4 days, compared to 26.7 days for those who underwent flap surgery. This difference was statistically significant (P=0.0003). This study evaluated the use of primary closure in patients who underwent resection of malignant lesions in the oral and maxillofacial area. Although the majority of patients underwent reconstruction with flaps, our results showed that primary closure can be a viable option for certain patients with early-stage lesions. Therefore, oral and maxillofacial surgeons should carefully consider various evaluation criteria and select appropriate reconstruction methods to optimize functional and aesthetic outcomes for each patient.

Aluminum (Al) and manganese (Mn) toxicity are the top two constraints to crop production in acid soil. Crops have evolved common and specific mechanisms to tolerate the two stresses. In the present study, the responses (toxicity and tolerance) of wheat near-isogenic lines (ET8 and ES8) and their parents (Carazinho and Egret) to Al and Mn were compared by determining physiolog-ical parameters and transcriptome profiling of roots. The results showed that: (1) Carazinho and ET8 exhibited dual tolerance to Al and Mn as compared with Egret and ES8, indicated by higher relative root elongation and SPAD; (2) After entering into roots, Al was mainly distributed in the root and fixed in the cell wall, while Mn was mainly distributed in the cell sap and then trans-ported to leaves. Both Al and Mn stresses decreased the contents of Ca, Mg, and Zn; Mn stress al-so inhibited the accumulation of Fe, while Al showed an opposite effect; (3) Transcriptomic analy-sis identified 5581 differentially expressed genes (DEGs) under Al stress and 4165 DEGs under Mn stress. Among these, 2774 DEGs were regulated by both Al and Mn stresses, while 2280 and 1957 DEGs were exclusively regulated by Al and Mn stress, respectively. GO and KEGG analyses indi-cated that cell wall metabolism responds exclusively to Al, while nicotianamine synthesis exclu-sively responds to Mn. Pathways such as signaling, phenylpropanoid metabolism, and metal ion transport showed commonality and specificity to Al and Mn. TFs, such as MYB, WRKY, and AP2 families, were also regulated by Al and Mn, and WGCNA identified PODP7, VATB2, and ABCC3 as the hub genes for Al tolerance and NAS for Mn tolerance. The identified genes and pathways can be used as targets for pyramiding genes and breeding multi-tolerant varieties.

A novel scheme that can simultaneously measure the Doppler frequency shift (DFS) and angle of arrival (AOA) of microwave signals is proposed. At the signal receiving unit (SRU), two echo signals and the reference signal are modulated by a Sagnac loop structure and sent to the central station (CS) for processing. At the CS, two low-frequency electrical signals are generated after polarization control and photoelectric conversion. The DFS without direction ambiguity and wide AOA measurement can be real-time acquired by monitoring the frequency and power of the two low-frequency electrical signals. In the simulation, an unambiguous DFS measurement with errors of ±3×10-3 Hz and a -90° to 90° AOA measurement range with errors of less than ±0.5° are realized. The safety and robustness of the system to environmental disturbance are improved, and it is more suitable for the modern electronic warfare system.

To ensure consumers can purchase high-quality rice, accurate identification of rice varieties is particularly important. Methods: This article conducts research based on machine learning algorithms from the perspectives of image, spectrum, and spectrogram fusion. Six types of hyperspectral image data of rice were preprocessed using convolutional smoothing (SG) and multiple scatter correction (MSC). Texture information of the images was extracted using gray-level co-occurrence matrix. Spectra, texture, and spectrogram data were fused into a new matrix. Spectral, texture, and spectrogram fusion data were used as inputs for the model, and support vector machines (SVM), logistic regression (LR), and K-nearest neighbors (KNN) classification models were constructed and compared. Results: From the classification results, the spectrogram fusion classification performance was better than classification models using only spectra or texture. Conclusion: The research results showed that the accuracy of SVM and LR classification models exceeded 90%, and the LR model performed the best, effectively classifying rice varieties.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

Urbanization and industrialization processes in Mongolia have been significant and rapid for the last half-century. During this period, changes in political and economic systems, growth in the population, and the occasional harsh climate conditions were subject to fluctuations in the natural resource usage. The total Ecological Footprint (EF) in Mongolia has increased from 6.8 million global hectares (gha) in 1961 to 14.6 million gha in 2012. However, Biocapacity (BC) has decreased from 50.6 million gha in 1961 to 39.0 million gha in 2012. The study shows that grazing land Footprint and carbon uptake land Footprint are the two major contributors of the recent intensified use of biological resources. To ensure stable economic development and sustainable use of natural resources, environmental planning is required to consider both the population’s pressure on the environment and the ecosystem’s regeneration capacity, simultaneously. We have proposed a few possible strategies for sustainable utilization of grazing land Footprint and carbon Footprint. For grazing land Footprint, efficient management of both herding practice and number of animals should be considered. In case of carbon Footprint, it is estimated that with the improved combustion efficiencies of coal-based power plants and the maximum use of renewable energy, carbon dioxide (CO₂) emissions in Mongolia can be reduced up to 30% compared to the base line business as usual case in 2030.

Alcohol abuse can lead to alcoholic liver disease, becoming a major global burden. Hovenia dulcis fruit peduncle polysaccharides (HDPs) has the potential to alleviate alcoholic liver injury may play essential roles in treating for alcohol-exposed liver disease, however, the hepatoprotective effects and mechanisms remain unclear. In this study, the hepatoprotective effects of HDPs and its potential mechanisms were investigated in alcohol-exposed mice by liver metabolomics and gut microbiome. The results found that HDPs reduced medium-dose alcohol-caused dyslipidemia (significantly elevated T-CHO, TG, LDL-C), elevated liver glycogen levels and inhibited intestinal-hepatic inflammation (significantly decreased IL-4, IFN-γ and TNF-α), consequently reversing hepatic pathological changes. By applying gut microbiome analysis, HDPs showed significant decreases in Proteobacteria while significant increases in Firmicutes at the phylum level, and increased Lactobacillus abundance while decreased Enterobacteria abundance, maintaining the composition of gut microbiota. Further hepatic metabolomics analysis revealed that HDPs had a regulatory effect on hepatic fatty acid metabolism, by increasing the major metabolic pathways including arachidonic acid metabolism and glycerophospholipid metabolism and identified two important metabolites C00157 and C04230 involved in the above metabolism. Overall, HDPs reduced intestinal dysbiosis and hepatic fatty acid metabolism disorders in alcohol-exposed mice, suggesting that HDPs has a beneficial effect on alleviating alcohol-induced hepatic metabolic disorders.

The Silk Road pattern (SRP) and Circumglobal teleconnection pattern (CGT) are two well-known teleconnection patterns along the Eurasian westerly jet during boreal summer, which are often regarded as one teleconnection pattern. In view of the distinct features of the SRP/CGT on the interannual (IA) and interdecadal (ID) timescales, the present study investigates the linkages and differences between the SRP and CGT on the two timescales. On the IA timescale, the SRP and CGT feature a similar circumglobal wave train structure with strong and significant centers over Eurasia, but show clear independences. Specifically, the SRP and CGT illustrates largely the mid-/high-latitude-related and tropics-related parts of the Northern Hemisphere upper-tropospheric circulation variations, respectively. Also, the CGT shows a stronger connection to the Indian summer monsoon (ISM) heating and El Niño–Southern Oscillation than the SRP, which makes the CGT more like a tropical-forcing-driven atmospheric mode but the SRP more like an internal atmospheric mode. The linkages and differences between them are associated with their asymmetry relationship during their positive and negative phases, which are attributed mainly to the asymmetry impact of the ISM heating/cooling on the Eurasian circulations. On the ID timescale, the SRP and CGT are characterized by a coherent two-wave train structure over Eurasia, and feature more like the same teleconnection pattern, which are associated with the Pacific Decadal Oscillation and Atlantic Multidecadal Oscillation. The present findings on the linkages and differences between the SRP and CGT are helpful to understand the variability and prediction of the SRP and CGT.

The advancement in science and technology has led to luffa sponge (LS) being widely used as a natural material in industrial application as its polyporous structure and light texture. In order to enhance the utility of LS fibers as the reinforcement of lightweight composite materials, this study investigate its water absorption, mechanical properties, anatomical characteristic and thermal performance. Hence, moisture regain, tensile properties of LS fiber bundles were measured in accordance with standards and the structural characteristics were investigated via microscopic observation. Scanning electron microscopy (SEM) was used to observe the surface morphology and fracture surface of fiber bundles. Test results shows that the special structure where the phloem tissues degenerate to cavities had a significant influence on the mechanical properties of LS fiber bundles. Additionally, the transverse sectional area occupied by fibers in a fiber bundle (SF), wall thickness and ratio of wall to lumen of fiber cell, and crystallinity of cellulose had an impact on the mechanical properties of LS fiber bundles. Furthermore, the fiber bundles density of LS varies range of 385.46-468.70 kg/m³, much less than that of jute (1360.40 kg/m³) and Arenga engleri (950.20 kg/m³) while LS fiber bundles has superior specific modulus.

This paper provides attempts to formalize Hayek’s theory of knowledge. It has been theoretically shown that exponential income distribution is a spontaneous order of the well-functioning market economy. We show that this theoretical result is supported by the empirical evidence from the United Kingdom and China. In particular, we empirically show how the income structure of China evolved towards an exponential distribution after the market-oriented economic reformation. Furthermore, we strictly prove that, if the income structure of an economy obeys an exponential distribution, the income summation over all households leads to an aggregate production function with Hicks-neutral-like technical progress, in which the technology factor is exactly equal to society’s information stock that is a result of combining all of decentralized decisions.

In order to improve the adaptability of broilers to low-temperature environments and their ability to resist acute cold stress (ACS), 240 one-day-old broilers were selected and randomly divided into three groups. The control treatment (CC) was raised at the conventional feeding temperature from 1-43 days (d), the cold stimulation treatments (CS) were kept at 3 °C below the temperature of CC at 1-d intervals for 3 and 6 hours from 15 to 35 d, namely CS3 and CS6, respectively. Then all broilers were kept at 20 °C from 36 to 43 d. ACS was then carried out at 44 d, and the ambient temperature was dropped to 10 °C for 6 hours. The study investigated the production perfor-mance, as well as levels of intestinal barrier genes (including Claudin-1, E-cadherin, Occludin, ZO-1, ZO-2 and Mucin2), secretory IgA in duodenum and jejunum, and immunoglobulins (IgA and IgG) in serum. The results showed that IMCS could increase the daily weight gain and decrease the feed conversion ratio. During the IMCS, the expression levels of intestinal barrier genes were up-regulated and the content of secretory IgA was increased. When IMCS ceased for one week, the level of immunoglobulins in serum stabilized, and the expression levels of Occludin, ZO-2 and Mucin2 still maintained high levels. After ACS, broilers that received IMCS training maintained the high levels of intestinal barrier genes and secretory IgA.

The development of computational acoustics allows simulation of sound generation and propagation in complex environment. In particular, meshfree methods are widely used to solve acoustics problems through arbitrarily distributed field points and approximation smoothness flexibility. As a Lagrangian meshfree method, smoothed particle hydrodynamics (SPH) method reduce the difficulty in solving problems with deformable boundaries, complex topologies, or multiphase medium. The traditional SPH method has been applied in acoustic simulation. This study presents the corrective smoothed particle method (CSPM), which is a combination of SPH kernel estimate and Taylor series expansion. The CSPM is introduced as a Lagrangian approach to improve accuracy in solving acoustic wave equations in the time domain. Moreover, a boundary treatment technique based on the hybrid meshfree and finite difference time domain (FDTD) method is proposed to represent different acoustic boundaries with particles. To model sound propagation in pipes with different boundaries, soft, rigid, and absorbing boundary conditions are built with this technique. Numerical results show that the CSPM algorithm is consistent and demonstrates convergence with exact solutions. Main computational parameters are discussed, and different boundary conditions are validated to be effective for benchmark problems in computational acoustics.