Background and Objective: Although whole body-electromyostimulation (WB-EMS) has been shown to favorably improve body composition in several research studies, it has not been confirmed how it affects adipose tissue-derived biomarkers and circumferences of the abdomen and thighs. Materials and Methods: Twenty participants of obese elderly women were randomly classified into an EMS group (EMSG; n = 10) or a non-EMS group (CON; n = 10). The WB-EMS suits used in this study enabled the simultaneous activation of 8 muscle groups with selectable intensities for each phase. Stimulation frequency was selected at 85 Hz, impulse-width at 350 μ seconds, and impulse-rise as a rectangular application. Impulse duration was 6 seconds with a 4-second break between impulses. The EMS sessions were combined with aerobic dancing 3 times a week for 12 weeks. Both groups received the same program; however, the CON did not receive electrical stimuli. Biomarkers and body composition including circumferences of the abdomen and thighs were measured on Week 0 and Week 12. Results: Compared with the CON, 1) a significant effect of the EMS-intervention concerning decreased body weight (p = 0.032) and increased basal metabolic rate (p = 0.029) were evident. The thigh subcutaneous fat and total fat of EMSG were not significantly changed, but those of CON were significantly increased after 12 weeks. 2) The biomarkers of CON either increased or showed no change, although the interleukin (IL)-6 was significantly (p = 0.028) decreased in EMSG. Specifically, C-reactive protein (CRP; p = 0.005) and alpha-fetoprotein (p = 0.050) of CON were significantly increased after 12 weeks. In addition, the IL-6 (p = 0.034), CRP (p = 0.001), carcinoembryonic antigen (p = 0.017), and low density lipoprotein (p = 0.005) of EMSG were lower than those of CON in the end of experiment. 3) Conclusions: The results indicate that EMS intervention improved body composition and reduced negative biomarkers, thus highlighting its effectiveness.

Resection of malignant lesions in the oral and maxillofacial area causes functional and morphological defects. To recover from these defects, reconstruction surgery is needed such as a primary closure or a flap. There are advantages and disadvantages to the method of using the primary closure and the flap, and the choice of procedure is entirely up to a surgeon. The purpose of this study is to evaluate availability of primary closure in patients. For 10 years from January 2010 to May 2020, patients who recovered using flaps after removing malignant lesions from the oral cavity and those who closed the lesion using primary closure were investigated. The investigation was conducted by searching the database of the hospital. There were 85 patients who removed malignant lesions in the oral and maxillofacial area, and among them 16 patients closed the soft tissue defects using primary closure. Operation time, histologic types, stages, wound status, and period of hospitalization according to the patients' medical records were investigated retrospectively. Between the staging and the primary closure, statistically significant differences were observed between stage I and stage II patients in 13 patients using the primary closure. (P=0.046). Statistically significant differences were identified between operation time and primary closure, with an average of 4.02 hours (P=0.015). The average period of hospitality for patients who underwent primary closure was 13.4 days, compared to 26.7 days for those who underwent flap surgery. This difference was statistically significant (P=0.0003). This study evaluated the use of primary closure in patients who underwent resection of malignant lesions in the oral and maxillofacial area. Although the majority of patients underwent reconstruction with flaps, our results showed that primary closure can be a viable option for certain patients with early-stage lesions. Therefore, oral and maxillofacial surgeons should carefully consider various evaluation criteria and select appropriate reconstruction methods to optimize functional and aesthetic outcomes for each patient.

Colorectal cancer (CRC) is the third most commonly diagnosed cancer worldwide, and despite advances in treatment, survival rates are still low; therefore, the development of novel drugs is imperative. Acetylcorynoline (ACN) is derived from Corydalis ambigua. The effect of ACN on colon cancer is still unknown. Therefore, we investigated its potential effects. Our data showed that ACN inhibited cell viability and proliferation. Moreover, ACN induced apoptosis and cell cycle arrest by inhibiting cell growth. In the present study, we hypothesized that ACN regulates c-Myc through CNOT2 or MID1IP1. ACN reduced the protein expression of oncogenic genes, decreased c-Myc half-life, and rapidly inhibited the serum stimulation response. Moreover, knockdown of CNOT2 and MID1IP1 with ACN increased apoptosis and further reduced the expression of oncogenes. In addition, ACN exhibited a synergistic effect with low-dose of 5-fluorouracil (5-FU) and doxorubicin (Dox). Collectively, our data demonstrates that ACN inhibited c-Myc expression through CNOT2 and MID1IP1 and induced apoptosis. These findings indicate the potential of ACN as a therapeutic agent against colon cancer.

We present a distributed optical-fiber temperature sensor with enhanced sensitivity based on an Al-coated fiber using the Rayleigh backscattering spectra (RBS) shift in optical frequency-domain reflectometry (OFDR). The Al-coated sensing fiber with a higher thermal expansion coefficient compared to silica produces a strain-coupled shift in the RBS under an increase in temperature. This effect leads to an enhanced temperature sensitivity of the distributed measurement scheme. Our results revealed that the temperature sensitivity obtained using the Al-coated fiber in OFDR was ~56% higher relative to that of a single-mode fiber. Moreover, the minimum measurable temperature recorded was 1 °C with a spatial resolution of 5 cm.

The present study was conducted to investigate the effects of rhizome extract of Dioscorea batatas (Dioscoreae Rhizoma, Chinese Yam) and its bioactive compound, allantoin, on myoblast differentiation and mitochondrial biogenesis in skeletal muscle cells. Yams were extracted in water and the extract was analyzed by HPLC. The expression of C2C12 myotubes differentiation and mitochondrial biogenesis regulators were determined by reverse transcriptase (RT)-PCR or Western blot. The glucose levels and total ATP contents were determined by glucose consumption, glucose uptake and ATP assays, respectively. Treatment with yam extract (1 mg/mL) and allantoin (0.2 and 0.5 mM) significantly increased of MyHC expression compared with non-treated myotubes. Yam extract and allantoin significantly increased the expression of mitochondrial biogenesis regulating proteins, PGC1?, Sirt-1, NRF-1, and TFAM, as well as the phosphorylation of AMPK and ACC in C2C12 myotubes. Furthermore, yam extract and allantoin significantly increased the glucose uptake levels and the ATP contents. Finally, HPLC analysis revealed that the yam extract contained 1.53% of allantoin. Yam extract and allantoin, stimulated myoblast differentiation into myotubes and increased energy production through upregulation of mitochondrial biogenesis regulators. These findings indicate that yam extract and allantoin can help to prevent the skeletal muscle dysfunction through stimulation of energy metabolism.

The biological synthesis of nanoparticles has been emerging as an environmentally benign and eco-friendly method owing to its cost-effectiveness and high efficiency. Recently, the biological synthesis of semiconductor and metal-doped semiconductor nanoparticles with enhanced photocatalytic degradation efficiency and anticancer and antibacterial properties have gained tremendous attention. In pursuit of this purpose, for the first time, we biosynthesized zinc oxide (ZnO) and silver/ZnO nanocomposites (NCs) as semiconductor and metal-doped semiconductor nanoparticles, respectively, using the cell-free filtrate (CFF) of Lysinibacillus sphaericus bacterium. The biosynthesized ZnO and Ag/ZnO were characterized by various techniques such as ultraviolet-visible spectroscopy, X-ray diffraction, Fourier-transform Infrared spectroscopy, Field-emission scanning electron microscopy, transmission electron microscopy, and photoluminescence spectroscopy. The photocatalytic degradation potential of these semiconductor/metal-semiconductor nanoparticles was evaluated against the degradation of azo dye methylene blue (MB) under simulated solar irradiation. Ag/ZnO showed 90.7 ± 0.91% photocatalytic degradation of MB, compared to 50.7 ± 0.53% by ZnO in 120 min. The cytotoxicity of ZnO and Ag/ZnO on human cervical HeLa cancer cells was determined using an MTT assay. Both nanomaterials exhibited cytotoxicity in a concentration-dependent and time-dependent manner on HeLa cells. The antibacterial activity was also determined against Gram-negative (Escherichia coli) and Gram-positive (Staphylococcus aureus). Compared to ZnO, Ag/ZnO NPs showed higher antibacterial activity. Hence, the biosynthesis of semiconductor nanoparticles could be a promising strategy for developing hybrid metal/semiconductor nanomaterials for different biomedical and environmental applications.

The phylogenetic relationships among the Peninsular Malaysian orchid genus Coelogyne were studied by morphological characteristics and by sequencing the internal transcribed region (ITS) from the nuclear ribosomal DNA (nrDNA). Coelogyne is a large genus of about 200 species distributed in pantropical areas from the Himalayas, Sri Lanka, India, Southern China and throughout South East Asia to Papua New Guinea. The widely accepted previous classification system was exclusively based on floral morphology. There were very few molecular systematic studies of Coelogyne done in Peninsular Malaysia thus far. In this study, 59 Coelogyne taxa were collected from throughout Peninsular Malaysia and 57 of them were identified to the species level. To study the phylogeny of this genus, morphological characters were utilized together with molecular evidences to generate the systematic hypotheses. Cluster analysis was performed using both the vegetative and floral characters. The results showed that three sections of Peninsular Malaysian Coelogyne, namely Longifoliae, Speciosae and Fuliginosae were sister groups which were more closely related by forming one clade than they were with the other sections. Another clade consisted of four other sections, namely Flaccidae, Coelogynae, Tomentosae and Verrucosae. Molecular phylogenies obtained by using the Neighbour Joining method revealed the close relationship between the sections Tomentosae and Verrucosae, whereas usage of the Maximum Likelihood method demonstrated that three sections namely Longifoliae, Speciosae and Fuliginosae were sister groups since they formed a single clade.

Suppressors of cytokine signaling (SOCS) influence cytokine and growth factor signaling by negatively regulating the JAK-STAT pathway. This maintains homeostasis during host immune response. However, functional characterization of SOCS family members in invertebrates is limited. In this study, we discovered the Type-I subfamily of the SOCS genes in the mealworm beetle, T. molitor. The full-length ORFs of TmSOCS5, TmSOCS6, and TmSOCS7 consisted of 1,389, 897 and 1,458 nucleotides, encoding polypeptides of 462, 297 and 485 amino acids, respectively, The C-terminal region of TmSOCS was highly conserved in the SH2 and SOCS box domains. Phylogenetic analysis revealed that the three SOCS genes clustered within the same sub-family and the highest amino acid identity was with the Tribolium castaneum SOCS genes (TcSOCS). While the expression of TmSOCS5 and TmSOCS6 was low in larval, pupal, and adult stages of the insect, TmSOCS7 showed higher expression. The expression of TmSOCS5 and TmSOCS6 was higher in larval hemocytes and adult ovary. The microbes expressed the three TmSOCS genes to varying degrees. C. albicans elicited the strongest response in the host with highest 15-fold expression in TmSOCS7 3 h post-inoculation. Collectively, these data suggest that the Type I TmSOCS could play a role in eliciting host immunity.

In the crustacean immune system, leucine-rich repeat (LRR) is one of the major structures for recognizing pathogen-associated molecular patterns (PAMPs). LRR domain-containing proteins belong to the LRR family, which is a large group of proteins with more than 6000 genes in the database. They are involved in very diverse physiological functions mainly by interacting with other proteins. In a previous study, the LvLRRm, a transmembrane protein containing only LRR domain, was identified in the white leg shrimp, Litopenaeus vannamei. Its versatile role in performing multiple immunomodulation activities has been reported. However, there is still a lack of research on its efficient function at the protein level. To investigate its interactions with other proteins, we applied a convenient method called ‘Hybrid LRR technique’ to produce a recombinant LvLRRm. The LvLRRm and hagfish’s variable lymphocyte receptors (VLRs) fragments were fused to the conserved LxxLxLxxN motif while retaining the β-strand. In addition, we established interactions between hybrid-proteins and flagellin of Salmonella by performing surface plasmon resonance (SPR) analysis. The designed hybrid proteins showed potential for universal applications without losing protein functions.

Electromyostimulation (EMS) has been shown to improve body composition, but what biomarkers it affects has not been investigated. The purpose of this study was to compare the EMS-effect of aerobic dance on fatness and biomarkers’ levels in obese elderly women. Methods: Twenty-five women with obesity were randomly classified into a control group (CON; n = 12) and EMS group (EMSG; n = 13). EMS suits used in this study enabled the simultaneous activation of eight muscles with selectable intensities. Program sessions of EMS were combined with aerobic dance three times a week for 8 weeks. Although both groups received the same program, CON did not receive electrical stimuli. Results: Compared with CON, a significant effect of the EMS intervention concerning decreased fatness, as well as an increased skeletal muscle mass and basal metabolic rate, were evident. Compared with CON, aerobic dancing with an EMS suit also improved biomarkers in EMSG. Cytokines, including interleukin-6, tumor necrosis factor, C-reactive protein, resistin, and carcinoembryonic antigen were significantly changed in EMSG, whereas those of CON did not change from the baseline to the end of the experiment. These results showed significant differences between groups. Similarly, the changes caused by EMS were represented in high-density lipoprotein-cholesterol and low-density lipoprotein-cholesterol. Conclusions: The results indicate that a significant effect due to the EMS intervention was found concerning body composition and biomarkers in obese elderly women.

Herein, we developed a highly sensitive and specific bimolecular fluorescence complementation (BiFC)-based influenza A virus (IAV) sensing system created by combining a galactose/glucose-binding protein (GGBP) with an N-terminal large domain (YN1-172) and a C-terminal small domain (YC173-239) of enhanced yellow fluorescence protein (eYFP). The GGBP-based BiFC reporter exhibits the fluorescence reconstitution as a result of conformational changes in GGBP when lactose, derived from 6’-silalyllactose used as a substrate for neuraminidase (NA), binds to GGBP in the presence of IAV. The system showed a linear dynamic range from 1 x 100 TCID50/mL to 1 x 107 TCID50/mL, with a detection limit of 4 x 101 TCID50/mL for IAV (H1N1), demonstrating ultra-high sensitivity. Our system exhibited fluorescence intensity enhancements in the presence of IAV, while displaying weak fluorescence signals when exposed to NA-deficient viruses such as RSV A, RSV B, adenovirus and rhinovirus, thereby indicating selective responses for IAV detection. Taken together, our system provides a simple, highly sensitive and specific IAV detection platform based on BiFC capable of detecting the ligand-induced protein conformational changes, obviating the need for virus culture or RNA extraction processes.

Studies have shown increased nontuberculous mycobacterial pulmonary disease (NTM) incidence with inhaled corticosteroid (ICS) use in patients with chronic respiratory diseases; however, this association in chronic obstructive pulmonary disease (COPD) remains insufficiently studied. Using a nationwide population-based database of the Korean National Health Insurance Service, newly diagnosed COPD patients (20052018) treated with inhaled bronchodilators were selected. An NTM case was defined by the presence of the first diagnostic code following inhaled bronchodilator use. Results indicated that ICS users did not have an increased risk of NTM disease compared to non-ICS users (hazard ratio [HR], 1.121; 95% confidence interval [CI], 0.9501.323; p = 0.1755). The highest quartile of the cumulative ICS dose was associated with the development of NTM (1.200, 0.9501.323, p = 0.0497). Medium (1.229, 1.0081.499, p = 0.0410) and high daily doses of ICS (1.637, 1.2412.160, p = 0.0005) were associated with an increased risk of NTM disease. There was no difference in the risk of NTM according to ICS type. ICS use may not increase the risk of developing NTM disease in patients with COPD. However, physicians should weigh the potential benefits and risks of ICS, especially when using high doses and prolonged durations.

Purpose: To evaluate clinical outcomes after bilateral mix-and-match cataract surgery using extended depth of focus (EDOF) and diffractive multifocal (DMF) intraocular lenses (IOLs). Methods: Thirty-seven patients received Tecnis Symfony EDOF IOL (ZXR00) implantation in the dominant eye, and Tecnis +3.25 DMF IOL (ZLB00) in the non-dominant eye. Patients were followed for 3 months, and uncorrected and corrected distance visual acuity (UDVA, CDVA) , uncorrected intermediate and near visual acuity (UIVA, UNVA), contrast sensitivity, defocus curves, stereopsis, and patient satisfaction were assessed. Results: At 3 months, mean logMAR UDVA was 0.07 ± 0.09 in EDOF IOL eyes, 0.12 ± 0.11 in DMF IOL eyes, and 0.02 ± 0.05 in both eyes. UIVA was 0.11 ± 0.11 in EDOF IOL eyes, 0.16 ± 0.12 in DMF IOL eyes, and 0.04 ± 0.07 in both eyes. UNVA was 0.25 ± 0.15 in EDOF IOL eyes, 0.22 ± 0.16 in DMF IOL eyes, and 0.13 ± 0.13 in both eyes. Thirty patients(81.1%) were more than satisfied with near vision, and 8 patients(21.6%) complained of severe glare and halo. Spectacle independence for near vision was achieved in 34 patients(91.9%), and 31 patients(83.8%) had better than a 50 second arc of stereopsis. Conclusion: Mix-and-match cataract surgery with EDOF and DMF IOL implantation provided good visual outcomes through all distances. Also excellent patient satisfaction was achieved with high level of spectacle independence and minimal photic phenomena.

This case report describes evidence of intratubular biomineralization in root canal filled with calcium enriched material after 8 years of clinical maintenance. The schematic findings of dentinal tubules were investigated with scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). The root canal obturation material was closely adapted to root dentin surface, suggesting the possibility of chemical bonding between the two interfaces. SEM and EDS observation of dentinal tubules showed intratubular biomineralized crystal structures with Ca/P ratio in a range of 1.30–2.12, suggesting bioactive capacity of calcium enriched cement.

This study examines the effect of a corporate citizenship-oriented high performance work system (CC-oriented HPWS) and the interactive influence of CC-oriented HPWS and person-organization fit (PO fit) on creativity at the individual level. Our analysis of field data collected from 303 employees in two branch companies with a two-phase collection method provides empirical support for our theoretical model. The results indicate that high performance work system (HPWS) reflecting corporate citizenship (CC) correlates positively with individual creativity. In addition, the moderating effect of PO fit is significant in the relationship between CC-oriented HPWS and creativity at the individual level. On this basis, this paper discusses the theoretical and practical implications of these findings for future research.

Breath volatile organic compound analysis is a non-invasive tool for assessing health status; the compositional profile of these compounds in the breath of patients with chronic kidney disease is believed to change with decreasing renal function. We aimed to identify breath volatile organic compounds for recognizing patients with chronic kidney disease. Using thermal desorption-gas chromatography-mass spectrometry, untargeted analysis of breath markers was performed using breath samples of healthy controls (n=18) versus non-dialysis (n=21) and hemodialysis (n=12) patients with chronic kidney disease in this cross-sectional study. A total of 303 volatile organic compounds alongside 12 clinical variables were used to determine the breath volatile organic compound profile. Metabolomic analysis revealed that age, systolic blood pressure, and fifty-eight breath volatile organic compounds differed significantly between the chronic kidney disease group (non-dialysis + hemodialysis) and healthy controls. Thirty-six volatile organic compounds and two clinical variables that showed significant associations with chronic kidney disease in the univariate analysis were further analyzed. Different spectras of breath volatile organic compounds between the control and chronic kidney disease groups were obtained. Multivariate model incorporating age, 2-methyl-pentane, and cyclohexanone showed high performance (accuracy, 86%) in identifying patients with chronic kidney disease, with odds ratios (95% confidence interval) P-values of 0.18 (0.07-2.49) 0.013; 2.10 (0.94-2.24) 0.025; and 2.31 (0.88–2.64) 0.008, respectively. Hence, renal dysfunction-associated characteristic profiles of breath volatile organic substances can be used as non-invasive markers to screen for chronic kidney disease.

Motivated by empirical observations, we propose a possible extension of Gibrat's law. By applying it into the random growth theory of income distribution (Gabaix, 2009), we find that the income distribution is described by a generalized Pareto-type distribution (GPD) with three parameters. We observe that there is a parameter /elta in the GPD that plays a key role in determining the shape of income distribution. By using the Kolmogorov-Smirnov test, we empirically show that, for typical market-economy countries, /elta is close to 0 significantly, such that the income distribution is characterized by a two-class pattern in which the bottom 90% of the population is approximated by an exponential distribution and the richest 1%~3% is approximated by an asymptotic power law. However, we empirically find that, for China both in planned economy period and in early stages of market reformation (from 1978 to 1990), /elta is significantly deviated from 0, such that the bottom of the population no longer conforms to an exponential distribution.

The aim of this study was to analyze whether the respiratory variation in ECG standard lead II R-wave amplitude (ΔRDII) could be used to assess intravascular volume status following inferior vena cava (IVC) clamping. This clamping causes an acute decrease in cardiac output during liver transplantation (LT). We retrospectively compared ΔRDII and related variables before and after IVC clamping in 34 recipients. Receiver operating characteristic (ROC) curve and area under the curve (AUC) analyses were used to derive a cutoff value of ΔRDII for predicting pulse pressure variation (PPV). After IVC clamping, cardiac output significantly decreased while ΔRDII significantly increased (P = 0.002). The cutoff value of ΔRDII for predicting a PPV >13% was 16.9% (AUC: 0.685) with a sensitivity of 57.9% and specificity of 77.6% (95% confidence interval 0.561 – 0.793, P = 0.015). Frequency analysis of ECG also significantly increased in the respiratory frequency band (P = 0.016). Although significant changes in ΔRDII during vena cava clamping were found at norepinephrine doses < 0.1 μg/kg/min (P = 0.014), such changes were not significant at norepinephrine doses > 0.1 μg/kg/minP = 0.093). ΔRDII could be a noninvasive dynamic parameter in LT recipients presenting with hemodynamic fluctuation. Based on our data, we recommended cautious interpretation of ΔRDII may be requisite according to vasopressor administration status.

As climate changes, our daily life has been much influenced by abnormal meteorological phenomena such as heavy rainfall, heat wave, heavy snowfall, and fine dust. Atmospheric air quality is worsening day by day and indoor air quality is also affected by interconnected daily activities throughout the inside and outside of buildings and houses. Nowadays, pollutants from various sources are emitted, transformed by sunlight, vapor, and ozone and transported into the city from country to country. Due to these reasons, there have been high demands to monitor the transportation of particulate matters and improve air quality. Monitoring of pollutants and identification of type and its concentration enables us to track and control its generation and consequently find out the solution. However, monitoring of pollutants, especially, particulate matter generation and its transportation is still not fully operated in atmospheric air due to its open nature and meteorological factors. Even though indoor air is relatively easy to monitor and control than outdoor in the aspect of specific volume and contaminant source, but it still needs to consider the meteorological parameters because indoor air is not fully separated from the outdoor air flow and contaminants transportation. In this study, optical approach using spectral sensor was attempted to reveal the feasibility of wavelength and chromaticity values of reflected light from specific particles. From the analysis of reflected light of various particulate matters according to different liquid additives, parameter studies were performed to investigate which experimental conditions can contribute to the enhanced selective sensing of particulate matters. Five different particulate matters such as household dust, soil, talc powder, gypsum powder and yellow pine tree pollen were utilized and observed to elucidate the relationship between property of particulate matter and detected light spectrum. Applicable approaches to assist current particle matter sensors and improve the selective sensing were suggested.

In this study, we repositioned thiopurine drugs used for the treatment of acute leukaemia as new tyrosinase inhibitors. Tyrosinase catalyses two distinct and successive oxidations in melanin biosynthesis: the conversions of tyrosine to dihydroxyphenylalanine (DOPA) and DOPA to dopaquinone. Continuous efforts are underway to discover small molecule inhibitors of tyrosinase for therapeutic, cosmetic, and agricultural purposes. Structure-based virtual screening has predicted inhibitor candidates for mushroom tyrosinase from drugs approved by the US Food and Drug Administration (FDA). Enzyme assays have confirmed the thiopurine leukaemia drug, thioguanine, as a tyrosinase inhibitor. Two other thiopurine drugs, mercaptopurine and azathioprine, were also evaluated for their tyrosinase inhibitory activity; mercaptopurine caused stronger inhibition than thioguanine did, whereas azathioprine was a poor inhibitor. The inhibitory constants of thioguanine and mercaptopurine were calculated as 52 and 16 µM, respectively, and the value of mercaptopurine was comparable to that of the well-known inhibitor kojic acid (13 µM). The cell lysate and melanin content assay in B16F10 melanoma cells confirmed that the compounds inhibited mammalian tyrosinase. In particular, 50 µM thioguanine reduced the melanin content by 57% without cytotoxicity. Furthermore, the thiopurine drugs shared little chemical similarity with the known tyrosinase inhibitors.

Since electrical resistivity of concrete can be measured in a more rapid and simple way than chloride diffusivity, it should be primarily regular quality control of the electrical resistivity of concrete which provides the basis for indirect of quality control of concrete durability during the concrete construction. If this is realized, the electrical resistivity of concrete can be a crucial parameter to establish maintenance strategy for marine concrete structures. Electrical resistivity of concrete is important to estimate two processes involved in corrosion of reinforcement: initiation (chloride penetration) and propagation (corrosion rate). The resistivity of concrete structure exposed to chloride indicates the risk of early corrosion damage, because a low resistivity is related to rapid chloride penetration and to high corrosion rate. Concrete resistivity is a geometry-independent material property that describes the electrical resistance, which is the ratio between applied voltage and resulting current in a unit cell. The current is carried by ions dissolved in the pore liquid. While some data exist on the relationship between moisture content on electrical resistivity of concrete, very little research has been conducted to evaluate the effect of chloride on the conduction of electricity through concrete. The purpose of this study is to examine and quantify the effect of pore water and chloride content on surface electrical resistivity measurement of concrete. It was obvious that chloride content had influenced the resistivity of concrete and the relationship showed a linear function. That is, concrete with chloride ions had a comparatively lower resistivity. Chloride can lead to underestimate the electrical resistivity of concrete. Conclusively, this paper suggested the quantitative solution to depict the electrical resistivity of concrete with various chloride contents.

The adapted Posner spatial cue-target paradigm was used to explore the relationship between exogenous temporal attention caused by rhythm and endogenous and exogenous spatial attention. The study was divided into two experiments. In Experiment 1, 33 participants used arrow cues to orient endogenous spatial attention and rhythm to orient exogenous temporal attention. In Experiment 2, with 29 participants, exogenous spatial attention was directed by highlighting the cue box. Exogenous temporal attention was directed by rhythm. Experiment 1 indicated that RTs were faster for attended targets than the unattended. The main effect of temporal attention was significant, with RTs being faster for synchrony and late compared to early. RTs were faster for late compared to synchrony. The main effect of stimulus repetition was significant, with faster RTs for targets when the rhythmic cue consisted of five compared to four. The interaction between spatial attention and temporal attention was not significant. Experiment 2 demonstrated that exogenous spatial attention only exhibited IOR under early four stimulus repetitions. The main effect of temporal attention was significant, with RTs being faster for synchrony and late compared to early. The main effect of stimulus repetition was significant, with faster RTs for targets when the rhythmic cue consisted of five compared to four. The interaction between spatial attention and temporal attention was significant. The results indicated that rhythmic temporal attention supported foreperiod effects. Exogenous temporal attention and endogenous spatial attention independently affect behavior, while exogenous temporal attention and exogenous spatial attention mutually influenced behavior.

OBJECTIVE: Although 3D-printed anatomic models are not new to medicine, the high costs and lengthy production times entailed have limited their application. Our goal was developing a new and less costly 3D modeling method to depict organ-tumor relations at faster printing speeds. METHODS: We have devised a method of 3D modeling using DICOM images. Coordinates are extracted at a specified interval, connecting them to create mesh-work replicas. Adjacent constructs are depicted by density variations, showing anatomic targets (ie, tumors) in contrasting color. RESULTS: An array of organ solid-tumor models were printed via Fused Deposition Modeling 3D printer at significantly less cost ($0.05/cm3) and time expenditure (1.73 min/cm3; both, p<.001). Printed models helped promote visual appreciation of organ-tumor anatomy and adjacent tissues. Our mesh-work 3D thyroidal prototype reproduced glangular size/contour and tumor location, readily approximating the surgical specimen. CONCLUSIONS: This newly devised mesh-type 3D printing method may facilitate anatomic modeling for personalized care and improve patient awareness during informed surgical consent.

Xerostomia is a subjective symptom of dry mouth resulting from various causes, including side effects of medication, systemic disorders, radiation, and Sjögren’s syndrome. Recently, the number of patients afflicted with xerostomia has increased due to an increase in the elderly population and patients on medication.; (2) Methods: A systematic approach is required to determine the etiology and management of xerostomia. This review summarizes recent literatures on the diagnosis and management of xerostomia.; (3) Results: A patient with xerostomia experiences difficulty in chewing, swallowing, speaking, tasting, and maintaining oral hygiene. Xerostomia and hyposalivation are uncomfortable side-effects in many patients. Assessing the function of the salivary gland is essential for selecting an appropriate treatment, improving symptoms, and preventing oral complications. Also, a more systematic approach is required to differentiate the subjective symptoms of the patient from the objective hyposalivation.; and (4) Conclusions: Although there is no standardized treatment for xerostomia, doctors need to endeavor and adapt the various treatments of xerostomia, to unearth the optimal treatment required for the patient.

Astroviruses (AstVs) have been detected in a wide range of animal species, including mammals and birds. Recently, a novel AstVs associated with neurological symptoms has been detected in the brain of some mammals. Raccoon dog AstV has been reported recently in China. However, there have been no reports in South Korea. Therefore, the present study aimed to detect and genetically characterize AstVs in intestine and brain tissues of 133 wild raccoon dogs collected in Korea between 2017 and 2019. Seven wild raccoon dogs were positive for AstV, four of which were also detected in brain tissue. Analysis of the capsid protein amino acid sequences of raccoon dog AstVs detected in Korea revealed a high similarity to canine AstVs, suggesting possible interspecies transmission between raccoon dogs and dogs. Phylogenetic and capsid protein amino acid sequence analysis of raccoon dog AstVs detected in brain 17-148B strain belonged to the HMO clade and exhibited conserved sequences found in neurotropic AstVs (NT-AstVs), indicating their potential as NT-AstVs. However, the pathogenicity and transmission routes of the raccoon dog AstV detected in Korea have not yet been elucidated, so further research and continued surveillance for AstV in wild raccoon dogs are needed.

World Health Organization (WHO) provides the guideline for managing the Particulate Matter (PM) level because when the PM level is higher, it threats the human health. For managing PM level, the procedure for measuring PM value is needed firstly. We use Tapered Element Oscillating Microbalance (TEOM)-based PM measuring sensors because it shows higher cost-effectiveness than Beta Attenuation Monitor (BAM)-based sensor. However, TEOM-based sensor has higher probability of malfunctioning than BAM-based sensor. In this paper, we call the overall malfunction as an anomaly, and we aim to detect anomalies for the maintenance of PM measuring sensors. We propose a novel architecture for solving the above aim that named as Hypothesis Pruning Generative Adversarial Network (HP-GAN). We experimentally compare the several anomaly detection architectures to certify ours performing better.

Hypoeutectic Al-Si-Cu-Mg alloys are promising candidates for use in automobile parts. Therefore, various attempts have been made to develop alternative casting technologies to improve the mechanical properties of cast alloys. In this study, the effects of modification with different levels of strontium (Sr) on primary and eutectic silicon (Si) in hypoeutectic Al-Si-Cu-Mg alloys were investigated. Using a gravity cast process, the Sr-modified samples were prepared from melts with four levels (100, 200, 300, and 400 ppm) of Sr. In addition, the wear properties of the cast samples were studied using a block-on-ring wear-testing machine. The sizes of the primary Si phases increased with increasing Sr content in the alloys. Moreover, more finely dispersed eutectic Si was observed with higher Sr content. In frictional wear tests, the specific wear rates of the test specimens decreased as the Sr content increased from 200 to 400 ppm. Coarse Si phases are considered to act as solid lubricants in the contact region during sliding.

Human adipose stem cell-derived extracellular vesicles (hASC-EVs) are key mediators of paracrine signaling with promising therapeutic applications. Although hASC-EVs are derived from human cells and are less immunogenic, their immunogenicity cannot be completely excluded. Here, we evaluate the immune responses of ICR and C57BL/6 mice to high doses of hASC-EVs for 10 days after injection. Lymphocyte subpopulations are analyzed using flow cytometry at 0.5, 1, 3 and 24 h post injection. In the spleen and blood of C57BL/6 mice, neutrophils sharply increased at 0.5 h and decreased at 3 h following hASC-EV treatment. We observe increased proportions of monocytes, macrophages, and natural killer cells at 3 h but returned to similar level of vehicle control at 24 h post injection in the spleen and blood of ICR mice. Although the in vivo experiments reveal different immune responses to hASC-EV treatment in C57BL/6 and ICR strains, no major changes occur in human peripheral blood mononuclear cell composition after applying hASC-EVs in vitro. In conclusion, unlike those in mice, immune responses to hASC-EVs in humans are not detectable, indicating a minimal risk of fatal side-effects from hASC-EV-based therapies.

Abstract: The frequency and intensity of air pollution are two of most critical issues the world faces in dealing with global environmental problems. They are both important areas that need to be improved. Our previous research [20] examines the assessment of fine dust pollution in Baekryeong island by statistical reasoning through one specific example of inland city (Yanggu) in Republic of Korea; however, given that Baekryeong Island is a remote island, there has been little focus on in-depth examination of its effect on the high density of fine dust in Baekryeong Island. The purpose of this article is twofold: (i) to examine the effect of a remote island on the high density of fine dust on Baekryeong Island using statistical reasoning and to provide a more specific statistical basis for the claim that one of the non-negligible factors influencing the high density of fine dust on Baekryeong Island is the geographic proximity to China; and (ii) to present brief discussion of fundamental cause of fine dust and global air pollution issues, which are not discussed in [20].

Flammability was evaluated and the results showed the values of critical flux at extinguishment (CFE) as 49.5kW/㎡ on average, total heat release (Qt) as 0.21MJ on average, and peak heat release rate (Qp) as 0.66kW on average, which satisfied all of the thresholds presented by the IMO. Therefore, flame-retardant plywood, of which the flame-retardant performance was evaluated, was determined to be an applicable finishing material that satisfies fire safety standards.

Abstract: The biological process of photosynthesis was critical in catalyzing the oxygenation of Earth’s atmosphere 2.5 billion years ago, changing the course of development of life on Earth. Recently, the fields of applied and synthetic photosynthesis have utilized the light-driven protein-pigment supercomplexes central to photosynthesis for the photocatalytic production of fuel and other various valuable products. The reaction center Photosystem I is of particular interest in applied photosynthesis due to its high stability post-purification, non-geopolitical limitation, and its ability to generate the greatest reducing power found in Nature. These remarkable properties have been harnessed for the photocatalytic production of a number of valuable products in the applied photosynthesis research field. These primarily include photocurrents and molecular hydrogen as fuels. The use of artificial reaction centers to generate substrates and reducing equivalents to drive non-photoactive enzymes for valuable product generation has been a long-standing area of interest of the synthetic photosynthesis research field. In this review, we cover advances in these areas and further speculate synthetic and applied photosynthesis as photocatalysts for the generation of valuable products.

Enveloped viruses represent a significant category of pathogens that cause serious diseases in animals. These viruses express envelope glycoproteins that are singularly important during infection of host cells by mediating fusion between the viral envelope and host cell membranes. Despite low homology at protein levels, three classes of viral fusion proteins have, as of yet, been identified based on structural similarities. Their incorporation into viral particles is dependent upon their proper sub-cellular localization after being expressed and folded properly in the endoplasmic reticulum (ER). However, viral protein expression can cause stress in the ER, and host cells respond to alleviate the ER stress in the form of the unfolded protein response (UPR); the effects of which have been observed potentiating or inhibiting viral infection. One important arm of UPR is to elevate the capacity of the ER-associated protein degradation (ERAD) pathway, which is comprised of host quality control machinery that ensures proper protein folding. In this review, we provide relevant details regarding viral envelope glycoproteins, UPR, ERAD, and their interactions in host cells.

In recent years, bone tissue engineering (BTE) has made significant progress in promoting the direct and functional connection between bone and graft, including osseointegration and osteoconduction, to facilitate the healing of damaged bone tissues. Herein, we introduce a new, environmentally friendly, and cost-effective method for synthesizing reduced graphene oxide (rGO) and hydroxyapatite (HAp). The method uses epigallocatechin-3-O-gallate (EGCG) as a reducing agent to synthesize rGO (E-rGO), and HAp powder is obtained from Atlantic bluefin tuna (Thunnus thynnus). The physicochemical analysis indicated that the E-rGO/HAp composites had exceptional properties for use as BTE scaffolds, as well as high purity. Moreover, we discovered that E-rGO/HAp composites facilitated not only proliferation, but also early and late osteogenic differentiation of human mesenchymal stem cells (hMSCs). Our work suggests that E-rGO/HAp composites may play a significant role in promoting the spontaneous osteogenic differentiation of hMSCs, and we envision that the E-rGO/HAp composites could serve as promising candidates for BTE scaffolds, stem cell differentiation stimulators, and implantable device components due to their biocompatible and bioactive properties. Overall, we suggest a new approach for developing cost-effective and environmentally friendly E-rGO/HAp composite materials for BTE application.

Honey bee (Apis mellifera) health is crucial for honey bee products, and effective pollination and is closely associated with gut bacteria. Various factors such as reduced habitat, temperature, disease, and diet affect the health of honey bees, by disturbing the homeostasis of the gut microbiota. In this study, high-throughput 16S rRNA gene sequencing was used to analyze the gut microbiota of Apis mellifera subjected to seven different diets. The identified microbiota in the Apis mellifera gut from all the diets consisted of Lactobacillus (62%), followed by Rhizobiaceae (21%), Snodgrassella (4%), and Erwiniaceae (4%) among other 33 genera. Based on diet types, Lactobacillus a lactic acid bacteria (LAB), dominates the microbiota with the highest relative abundance in AIGT+SAC (91%), AIGT+Soytide (88%), and AIGT+Apple juice (69%) diet groups. Bifidobacterium and Commensalibacter appeared as the second most abundant genera in AIGT+SAC and AIGT+Soytide diet groups, respectively. These bacteria are important markers for honey bee health. Considering the importance of these diets in shaping their host microbiome into a healthy status. Individual honey bee health (IHH) was observed to validate the quality and correlation between the microbiota and honey bee health. The results were consistent, indicating that Apis mellifera fed on AIGT+Soytide and AIGT+SAC diet showed the highest health expression level of vitellogenin. The group with 60%Syrup possessing Rhizobiaceae as the dominant taxa showed poor health status. This finding paved the way for establishing a link between gut microbiota and IHH under different diets.

This study aims to spatially analyze the distribution characteristics of vacant homes in Asan-si, Chungcheongnam-do, and understand the differences in factors causing vacant homes by type. We use a variety of statistical methods to examine these factors and identify key influencing factors such as the number of vacant stores, changes in overall population, land use complexity, and physical characteristics of land and buildings. The findings reveal that the factors contributing to the occurrence of vacant homes vary significantly by region and property type, highlighting the need for region-specific policies. For instance, in old town areas, small lot ratios and land use complexity are significant, while in rural village, the average number of floors and land use complexity play a major role. This study underscores the diversity of factors influencing vacant homes, suggesting that policies should be tailored to the unique characteristics of different regions to effectively address this issue.

: Medial temporal lobe atrophy (MTA) remains an important imaging biomarker in brain magnetic resonance imaging (MRI) for diagnosing and evaluating Alzheimer's disease (AD). We compared the detection performance for determining significant MTA and the correlation with Scheltens' scale between two automatic volumetry software, NeuroQuant® and Aqua®, in non-AD and AD groups. Overall, 127 (non-AD, 54; AD, 73) individuals who underwent three-dimensional T1-weighted volumetric MRI in our hospital between January and August 2011 were enrolled and retrospectively analyzed using NeuroQuant® and Aqua®. The accuracy, sensitivity, and specificity for detecting significant MTA and the correlation for Scheltens' scale with the mean hippocampal volume of each software were evaluated. The study sample’s mean age was 78 (range, 59–97) years. Regarding accuracy and specificity, Aqua® was non-inferior to NeuroQuant®. Aqua® had significantly higher overall specificity than NeuroQuant® for detecting significant MTA. Additionally, the calculated mean hippocampal volume of Aqua® was more correlated with Scheltens' scale (Kendall's τ, - 0.48) than that of NeuroQuant® (Kendall's τ, - 0.20). The accuracy and specificity of Aqua® in detecting MTA are not inferior to those of NeuroQuant®. Additionally, Aqua® has a stronger correlation of mean hippocampal volume with Scheltens' scale than NeuroQuant®.

To ensure consumers can purchase high-quality rice, accurate identification of rice varieties is particularly important. Methods: This article conducts research based on machine learning algorithms from the perspectives of image, spectrum, and spectrogram fusion. Six types of hyperspectral image data of rice were preprocessed using convolutional smoothing (SG) and multiple scatter correction (MSC). Texture information of the images was extracted using gray-level co-occurrence matrix. Spectra, texture, and spectrogram data were fused into a new matrix. Spectral, texture, and spectrogram fusion data were used as inputs for the model, and support vector machines (SVM), logistic regression (LR), and K-nearest neighbors (KNN) classification models were constructed and compared. Results: From the classification results, the spectrogram fusion classification performance was better than classification models using only spectra or texture. Conclusion: The research results showed that the accuracy of SVM and LR classification models exceeded 90%, and the LR model performed the best, effectively classifying rice varieties.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

Urbanization and industrialization processes in Mongolia have been significant and rapid for the last half-century. During this period, changes in political and economic systems, growth in the population, and the occasional harsh climate conditions were subject to fluctuations in the natural resource usage. The total Ecological Footprint (EF) in Mongolia has increased from 6.8 million global hectares (gha) in 1961 to 14.6 million gha in 2012. However, Biocapacity (BC) has decreased from 50.6 million gha in 1961 to 39.0 million gha in 2012. The study shows that grazing land Footprint and carbon uptake land Footprint are the two major contributors of the recent intensified use of biological resources. To ensure stable economic development and sustainable use of natural resources, environmental planning is required to consider both the population’s pressure on the environment and the ecosystem’s regeneration capacity, simultaneously. We have proposed a few possible strategies for sustainable utilization of grazing land Footprint and carbon Footprint. For grazing land Footprint, efficient management of both herding practice and number of animals should be considered. In case of carbon Footprint, it is estimated that with the improved combustion efficiencies of coal-based power plants and the maximum use of renewable energy, carbon dioxide (CO₂) emissions in Mongolia can be reduced up to 30% compared to the base line business as usual case in 2030.

Eruca sativa is a commonly used edible plant in Italian cuisine. E. sativa 70% ethanol extract (ES) was fractionated with five organic solvents. Ethyl acetate fraction(EEA) had the highest antioxidant activity, which was correlated with the total polyphenol and flavonoid content. ES and EEA acted as PPAR-α ligands by PPAR-α competitive binding assay. EEA significantly increased cornified envelope formation as a keratinocyte terminal differentiation marker in HaCaT cells. Further, it significantly reduced nitric oxide and pro-inflammatory cytokines in lipopolysaccharide-stimulated RAW 264.7 cells. The main flavonol forms detected in high amounts from EEA are mono-, and di-glycoside of each aglycone. Flavonol mono-glycosides were shown to be a potent PPAR-α ligand using molecular docking simulation and showed the inhibition of nitric oxide. These results suggest that E. sativa is suitable for use in improving skin barrier function and inflammation in skin disorders, such as atopic dermatitis.

The Silk Road pattern (SRP) and Circumglobal teleconnection pattern (CGT) are two well-known teleconnection patterns along the Eurasian westerly jet during boreal summer, which are often regarded as one teleconnection pattern. In view of the distinct features of the SRP/CGT on the interannual (IA) and interdecadal (ID) timescales, the present study investigates the linkages and differences between the SRP and CGT on the two timescales. On the IA timescale, the SRP and CGT feature a similar circumglobal wave train structure with strong and significant centers over Eurasia, but show clear independences. Specifically, the SRP and CGT illustrates largely the mid-/high-latitude-related and tropics-related parts of the Northern Hemisphere upper-tropospheric circulation variations, respectively. Also, the CGT shows a stronger connection to the Indian summer monsoon (ISM) heating and El Niño–Southern Oscillation than the SRP, which makes the CGT more like a tropical-forcing-driven atmospheric mode but the SRP more like an internal atmospheric mode. The linkages and differences between them are associated with their asymmetry relationship during their positive and negative phases, which are attributed mainly to the asymmetry impact of the ISM heating/cooling on the Eurasian circulations. On the ID timescale, the SRP and CGT are characterized by a coherent two-wave train structure over Eurasia, and feature more like the same teleconnection pattern, which are associated with the Pacific Decadal Oscillation and Atlantic Multidecadal Oscillation. The present findings on the linkages and differences between the SRP and CGT are helpful to understand the variability and prediction of the SRP and CGT.

This paper provides attempts to formalize Hayek’s theory of knowledge. It has been theoretically shown that exponential income distribution is a spontaneous order of the well-functioning market economy. We show that this theoretical result is supported by the empirical evidence from the United Kingdom and China. In particular, we empirically show how the income structure of China evolved towards an exponential distribution after the market-oriented economic reformation. Furthermore, we strictly prove that, if the income structure of an economy obeys an exponential distribution, the income summation over all households leads to an aggregate production function with Hicks-neutral-like technical progress, in which the technology factor is exactly equal to society’s information stock that is a result of combining all of decentralized decisions.

This paper presents a piezoresistive pressure sensor with a shield layer for improved stability. Compared with the conventional piezoresistive pressure sensors, p-type piezoresistors are covered by an n-type shield layer, which is formed by ion implantation. The proposed pressure sensors have been successfully fabricated by bulk micromachining techniques. The impact of electrical field on piezoresistors is studied by simulation. The temperature drift of the pressure sensor has been investigated by both simulation and experimental measurement. Characteristics of developed pressure sensors are tested from -40 C to 125 C. A sensitivity of 0.022 mV/V/KPa and a maximum non-linearity of 0.085% FS are measured for the fabricated sensor in a pressure range of 1 MPa. The temperature coefficients of resistance of shielded piezoresistors are found to be smaller than those of un-shielded ones. It is demonstrated that the shield layer is able to reduce the drift caused by electrical field and ambient temperature variation.

(1) Background : When placing implants in the maxillary posterior region with insufficient alveolar bone, a maxillary sinus elevation is necessary. Autogenous bone, though biologically ideal, poses risks and discomfort due to donor site harvesting. Block-type autogenous tooth bone graft material, made from the patient’s own extracted tooth, offers similar biological stability without these drawbacks; (2) Methods : This study observed the progress of 19 implant patients who were treated with maxillary sinus elevation procedures using block-type autogenous tooth bone graft material at the Daegu Catholic University Medical Center. Extracted teeth were processed into demineralized tooth block bone. After elevating the sinus membrane, implants and the tooth bone graft material were placed in the space, and the bony window was repositioned. Postoperative evaluations through clinical observation and radiographic imaging assessed sinus membrane elevation, alveolar bone height increase, and implant osseointegration; (3) Results : Results showed proportional increases in alveolar bone height to the graft material size, with long-term stability. No postoperative complications occurred, even with sinus membrane perforation, and implants remained stable; (4) Conclusions : The study concludes that maxillary sinus lifts using block-type autogenous tooth bone graft material provide excellent bone induction and biocompatibility, making it a highly beneficial method for both dentists and patients.

We show that an exponential income distribution will emerge spontaneously in a peer-to-peer economic network that shares the publicly available technology. Based on this finding, we identify the exponential income distribution as the benchmark structure of the well-functioning market economy. However, a real market economy may deviate from the well-functioning market economy. We show that the deviation is partly reflected as the invalidity of exponential distribution in describing the super-low income class that involves unemployment. In this regard, we find, theoretically, that the lower-bound u of exponential income distribution has a linear relationship with (per capita) unemployment compensation. In this paper, we test this relationship for the United Kingdom from 2001 to 2015. Our empirical investigation confirms that the income structure of low and middle classes (about 90% of populations) in the United Kingdom exactly obeys exponential distribution, in which the lower-bound u is exactly in line with the evolution of unemployment compensation.

This study investigated the impact of boron and copper on the microstructure and mechanical properties of Spheroidal graphite Cast Iron (SCI). The addition of boron increased the ferrite content, while copper increased the stability of pearlite. The interaction between boron and copper significantly increased the ferrite content. Differential Scanning Calorimetry (DSC) revealed that boron decreased the enthalpy change of the α + Fe3C -> γ transformation and increased the enthalpy change of the α -> γ transformation. The addition of boron and copper reduced the tensile and yield strength but increased elongation and impact energy. The findings provide valuable insights into the effect of boron and copper on SCI, facilitating the design and development of high-performance SCI materials.

Long-haul COVID-19 illness first gained widespread recognition among social support groups and later in scientific and medical communities. This illness is mysterious as it affects COVID-19 survivors at all levels of disease severity, even younger adults and children. While the precise definition may be lacking, the defining symptoms are fatigue, dyspnea, and headache that last for months after hospital discharge. The less typical symptoms may include cognitive impairments, chest and joint pains, myalgia, smell and taste dysfunctions, cough, mood changes, and gastrointestinal and cardiac issues. Presently, there is limited literature discussing the possible pathophysiology, risk factors, and treatments in long-haul COVID-19, which the current review aims to address. In brief, long-haul COVID-19 may be driven by long-term lung and brain damage and unresolved inflammation from multiple sources. The associated risk factors may include female sex, more than five early symptoms, early dyspnea, and specific biomarkers like D-dimer. While only rehabilitation training has been useful for long-haul COVID-19, therapeutics repurposed from mast cell activation syndrome, myalgic encephalomyelitis/chronic fatigue syndrome, and pulmonary fibrosis also hold potential. In sum, this review hopes to provide the current understanding of what is known about long-haul COVID-19.

Service robots operating in indoor environments should recognize dynamic changes from sensors, such as RGB-D camera, and recall the past context. Therefore, we propose a context query-processing framework, comprising spatio-temporal robotic context query language (ST-RCQL) and spatio-temporal robotic context query-processing system (ST-RCQP), for service robots. We designed them based on the spatio-temporal context ontology. ST-RCQL can query not only the current context knowledge but also the past. In addition, ST-RCQL includes a variety of time operators and time constants, and thus queries can be written very efficiently. The ST-RCQP is a query-processing system equipped with a perception handler, working memory, and backward reasoner for real-time query-processing. Moreover, ST-RCQP accelerates query-processing speed by building a spatio-temporal index in the working memory, where percepts are stored. Through various qualitative and quantitative experiments, we demonstrate the high efficiency and performance of the proposed context query-processing framework.

The development of printing technologies has enabled the realization of electric circuit fabrication on flexible substrate. However, the current technique remains restricted to single-layer patterning. In this paper, we demonstrate a fully solution-processable patterning approach for multi-layer circuits using a combined method of laser sintering and ablation. Selective laser sintering of silver (Ag) nanoparticle-based ink is applied to make conductive patterns on a heat-sensitive substrate and insulating layer. The laser beam path and irradiation fluence are controlled to create circuit patterns for flexible electronics. Microvia drilling using femtosecond laser through the polyvinylphenol-film insulating layer by laser ablation, as well as sequential coating of Ag ink and laser sintering, achieves an interlayer interconnection between multi-layer circuits. The dimension of microvia is determined by a sophisticated adjustment of laser focal position and intensity. Based on these methods, the flexible electronic circuit with chip-size-package light-emitting diodes was successfully fabricated and demonstrated with functional operations.

Osteoporosis is an abnormal bone remodeling condition characterized by decreased bone density, which leads to high risks of broken bones. Previous studies have demonstrated that Lycii Radicis Cortex (LRC) extract inhibits bone loss in ovariectomized (OVX) mice by enhancing the osteoblast differentiation. A bioactive compound, Kukoamine B (KB), was identified from a fractionation of LRC extract as a candidate component responsible for an anti-osteoporotic effect. This study investigated the anti-osteoporotic effects of KB using in vitro and in vivo osteoporosis models. KB treatment significantly increased the osteoblastic differentiation and mineralized nodule formation of osteoblastic MC3T3-E1 cells, while it significantly decreased the osteoclast differentiation of primary-cultured monocytes derived from mouse bone marrow. The effects of KB on osteoblastic and osteoclastic differentiations under more physiological conditions were also examined. In the co-culture of MC3T3-E1 cells and monocytes, KB promoted osteoblast differentiation but did not affect osteoclast differentiation. For the in vivo experiments, KB significantly inhibited OVX-induced bone mineral density loss and restored the impaired bone structural properties in osteoporosis model mice. These results suggest that KB may be a potential therapeutic candidate for the treatment of osteoporosis.

To address the insufficient mechanical properties of calcined phosphogypsum, this research aims to investigate the utilization of basalt fiber and calcium carbonate whiskers as reinforcing agents. The study examines their impact on the flexural and compressive strength, toughness, water resistance, and tensile strength of calcined phosphogypsum. In the individual tests, basalt fibers with different lengths (3 mm, 6 mm, 9 mm, and 18 mm) were added at dosages of 0%, 0.5%, 1.0%, and 1.5% respectively. The findings demonstrate that basalt fiber effectively enhances the flexural and compressive strength, toughness, and tensile strength of calcined phosphogypsum, albeit potentially compromising water resistance. Among the various fiber lengths, the 6 mm fibers exhibit the most advantageous influence on the performance of calcined phosphogypsum. A subsequent test was conducted to investigate the impact of cross-scale fibers on the properties of calcined phosphogypsum by mixing 6 mm basalt fibers and calcium carbonate whiskers. The results illustrate that calcium carbonate whisker refines the pores, thereby improving the flexural strength and toughness of calcined phosphogypsum. Furthermore, it compensates for the water resistance limitations associated with the sole utilization of basalt fiber while further augmenting the tensile strength and strain capacity. However, it should be noted that increasing the dosage of both calcium carbonate whiskers and basalt fibers concurrently leads to increased porosity of phosphogypsum and reduced compressive strength.

Hashimoto’s thyroiditis (HT) is a common autoimmune disease, with its prevalence rapidly increasing. Both genetic and environmental risk factors contribute to the development of HT. Recently, viral infection has been suggested to act as a trigger of HT by eliciting the host immune response and subsequent autoreactivity. We analyzed features of HT through bioinformatics analysis so as to identify markers of HT development. We accessed public microarray data of HT patients from the Gene Expression Omnibus (GEO) and obtained differentially expressed genes (DEGs) under HT. Gene Ontology (GO) and KEGG pathway enrichment analyses were performed for functional clustering of our protein-protein interaction (PPI) network. Utilizing ranked gene lists, we performed Gene Set Enrichment Analysis (GSEA) using the clusterprofiler R package. By comparing the expression signatures of the huge perturbation database with the queried rank-ordered gene list, connectivity map (CMap) analysis was performed to screen potential therapeutic targets and agents. The gene expression profile of the HT group was in line with general characteristics of HT. Biological processes related to the immune response and viral infection pathways were obtained for the upregulated DEGs. GSEA results revealed activation of autoimmune disease-related pathways and several viral infection pathways. Autoimmune disease and viral infection pathways were highly interconnected by common genes, while the HLA genes which are shared by both were significantly upregulated. CMap analysis suggested that perturbagens, including SRRM1, NLK, and CCDC92, have the potential to reverse the HT expression profile. Several lines of evidence suggested that viral infection and the host immune response are activated during HT. Viral infection is suspected to act as a key trigger of HT by causing autoimmunity. SRRM1, an alternative splicing factor, which responds to viral activity, might serve as potential marker of HT.

A space charge density wireless measurement system based on the idea of distributed measurement is proposed for collecting and monitoring the space charge density in an ultra-high-voltage direct-current (UHVDC) environment. The proposed system architecture is composed of a number of wireless nodes connected with space charge density sensors and a base station. The space charge density sensor based on atmospheric ion counter method is elaborated and developed, and the ARM microprocessor and Zigbee radio frequency module are applied. The wireless network communication quality and the relationship between energy consumption and transmission distance in the complicated electromagnetic environment is tested. Based on the experimental results, the proposed measurement system demonstrates that it can adapt to the complex electromagnetic environment under the UHVDC transmission lines and can accurately measure the space charge density.

Potential breeding habitat of egrets and herons was evaluated using the Maximum Entropy Model (MaxEnt). Model output can help guide management of nuisance egret and heron rookeries in urban forests of Daejeon Metropolitan City, Korea. This study examined 126 locations regarded as breeding sites of egrets and herons at the nationwide census conducted by the National Institute of Environmental Research between 2011 and 2012. In addition, 252 randomly selected locations were used to identify the significant variables among a total of 15 environmental variables within 4 factors (topography, natural environment, distance and climate). Twelve variables were significantly different between the breeding and randomly selected points. The final 10 variables were selected through Pearson’s correlation analysis. Using MaxEnt, breeding area was estimated using the 10 selected variables in Daejeon. The area under the receiver operating characteristic curve (AUC) was 0.950, which was the average value through 10-fold cross-validation to estimate the model reliability. The potential breeding habitat for egrets and herons was estimated to be 106.69 km2 (19.76% of the total area) in Daejeon. Within the estimated potential habitat, 11.82 km2 (12.46%) were less than 50 m from the residential district while 79.85 km2 (88.92%) were more than 50m from the residential district. Discriminative management strategies considering the breeding location of egrets and herons should be applied not only to minimize conflicts with residents, but also to maintain stable egret and heron breeding sites in Daejeon, Korea.

Coastal areas are increasingly being damaged with the expansion of seawater intrusion areas. We suggest a three-step method for reducing seawater intrusion areas by predicting future damage to groundwater being used continuously. First, the area most vulnerable to seawater intrusion damage is selected from among 25 areas on the west coast of the Republic of Korea. Having identified the Taean area as the region in question in the second step, we use RCP 4.5 and 8.5 as future sea level rise scenarios and predict the future usage of groundwater using linear-regression analysis of data for the past 10 years. Consequently, for RCP 8.5 (groundwater-usage scenario 1.0), 68.5% of the total Taean area is projected to be influenced by seawater intrusion. In the third step, the effectiveness of seawater intrusion reduction measures is analyzed considering the projected future situation and the local characteristics of the Taean area. After considering the effects of alternative locations, as well as seawater intrusion related data, alternatives were prioritized using a multi-criteria decision-making method. Consequently, 3, 5, and 4 were prioritized in the listed order, and we judged that by applying seawater intrusion area reduction measures according to this result, we will achieve the biggest effect.

This study delves into the atmospheric corrosion behavior of chromium-free complex-phase steel (CP), specifically investigating the influence of wet/dry frequency and ratio in cyclic corrosion tests (CCT). The study employs a modified ISO 14993 standard CCT method, which involves salt spray, dry, and wet stages. After 15 and 30 CCT cycles, mass loss, maximum corrosion depth, and corrosion products were analyzed to gain insights into corrosion mechanisms. In general, increasing the frequency and wet/dry stage ratio in CCT extends the time for autocatalytic reactions to occur, leading to accelerated localized CP corrosion and increased pitting factors. However, as the rust layer thickens, uniform corrosion may also intensify, so careful considerations are necessary. This study underscores the importance of controlling the frequency and ratio of wet/dry stages in CCT for effectively analyzing localized corrosion behavior in specimens.

Hemangioblasts give rise to endothelial progenitor cells (EPCs), which also express the cell surface markers CD133 and C-kit. They may differentiate into the outgrowth endothelial cells (OECs) that control neovascularization in the developing embryo. Reduced levels of EPC in circulation have been linked to human cardiovascular disorders, according to numerous studies. Furthermore, preeclampsia and senescence have been linked to levels of EPCs produced from cord blood. Uncertainties surround how preeclampsia affects the way EPCs function. It is reasonable to speculate that preeclampsia may have an impact on the function of fetal EPCs during the in utero period; however, given the present literature's suggestion that maternal vasculopathies, including preeclampsia, damage fetal circulation. Additionally, the differentiation potential and general activity of EPCs may serve as an indicator of the health of the fetal vascular system since they promote neovascularization and repair during pregnancy. Thus, the purpose of this review is to compare, through assessment of their quantity, differentiation potency, angiogenic activity, and senescence, the angiogenic function of fetal EPCs obtained from cord blood for normal and pregnancy problems. This will shed light on the relationship between the angiogenic function of fetal EPCs and pregnancy complications, which could have an effect on the management of long-term health issues like metabolic and cardiovascular disorders in offspring with abnormal vasculature development.

The intense motion of a ship can greatly impacts the comfort of crew members and the safety of the vessel. Therefore, accurately estimating and predicting ship attitudes has become an important issue. This paper introduces the latest development in functional deep learning model called DeepOnet. It takes wave height as input and ship motion as output, using a cause-to-result prediction approach. The modeling data used in this study is sourced from publicly available experimental data from the Iowa Institute of Hydraulic Research. Firstly, parameters system tuning was conducted for the neural network's hyperparameters to determine the appropriate combination of parameters. Secondly, the DeepOnet model for wave height and multi-degree-of-freedom motion was established, and the influence of increasing time steps on prediction accuracy was examined. Finally, a comparison was made between the DeepOnet model and the classical time series model LSTM. It was found that the DeepOnet model had a 10-fold improvement in accuracy for roll and heave attitudes. Moreover, as the forecast duration increased, the advantage of DeepOnet showed a trend of strengthening. As a functional prediction model, DeepOnet provides a new promising tool for very short-term prediction of ship motion.

ABSTRACT: Iodixanol is an iso-osmolar nonionic dimeric hydrophilic contrast agent with a higher viscosity than the monomeric agents. It is the only Food and Drug Administration (FDA)approved isoosmolar agent in the United States, and it is the only contrast agent with an FDA-approved indication for use in cardiac computed tomographic angiography (CCTA), to assist in the diagnostic evaluation of patients with suspected coronary artery disease. In clinical studies, it has been noted to have fewer side effects and similar image quality when compared to low osmolar contrast media. This can be attributed to the pharmacological properties of iodixanol. In the field of cardiology, iodixanol among other intravenous contrast media is used for coronary computed tomography angiography and cardiac catheterization. In this article, the use, tolerability and efficacy of iodixanol in the field of cardiology are reviewed, specifically evaluating the use for CCTA and coronary angiography, including outcome studies, randomized trials and comparisons to other contrast agents.

The non-pharmaceutical interventions implemented to prevent the spread of COVID-19 have affected the epidemiology of other respiratory viruses. In South Korea, Human metapneumovirus (HMPV) typically occurs from winter to the following spring; however, it was not detected for two years during the COVID-19 pandemic and re-emerged in the fall of 2022, which is a non-epidemic season. To examine the molecular genetic characteristics of HMPV before and after the COVID-19 pandemic, we analyzed 427 HMPV-positive samples collected in the Gwangju area from 2018 to 2022. Among these, 24 samples were subjected to whole-genome sequencing. The results showed a shift in the predominant genotype from A2b2 before the COVID-19 pandemic to A2b1 in 2022. Furthermore, a significant increase in HMPV cases was observed in the 6–10-year age group. Since the onset of the COVID-19 pandemic, social distancing have reduced the possibility of HMPV exposure and herd immunity due to non-transmission, resulting in the introduction of new HMPV genotypes in different seasons.

Although Eulerian approaches are standard in computational acoustics, they are less effective for certain classes of problems like bubble acoustics and combustion noise. A different approach for solving acoustic problems is to compute with individual particles following particle motion. In this paper, a Lagrangian approach to model sound propagation in moving fluid is presented and implemented numerically, using three meshfree methods to solve the Lagrangian acoustic perturbation equations (LAPE) in the time domain. The LAPE split the fluid dynamic equations into a set of hydrodynamic equations for the motion of fluid particles and perturbation equations for the acoustic quantities corresponding to each fluid particle. Then, three meshfree methods, the smoothed particle hydrodynamics (SPH) method, the corrective smoothed particle (CSP) method, and the generalized finite difference (GFD) method, are introduced to solve the LAPE and the linearized LAPE (LLAPE). The SPH and CSP methods are widely used meshfree methods, while the GFD method based on the Taylor series expansion can be easily extended to higher orders. Applications to modeling sound propagation in steady or unsteady fluids in motion are outlined, treating a number of different cases in one and two space dimensions. A comparison of the LAPE and the LLAPE using the three meshfree methods is also presented. The Lagrangian approach shows good agreement with exact solutions. The comparison indicates that the CSP and GFD method exhibit convergence in cases with different background flow. The GFD method is more accurate, while the CSP method can handle higher Courant numbers.

Background: We conducted research on the newly developed personalized recommendation service (PRS) of the global network of Korean scientists and engineers (KOSEN) in order to explore the information usage behavior and importance of the PRS used by Korean scientists and engineers. Methods: In order to understand information usage behavior, we gathered data from 513 survey results and analyzed them in terms of information usage behavior and the corresponding importance in each of the service quality areas. Results: We analyzed the 321 outcomes that indicated non-use of the PRS in order to understand the underlying reason(s); we employed 192 results that demonstrated the use of functionality to examine information usage behavior and importance. They found that the predominant motive for non-use of the service resulted from the respondents not knowing how to use it. According to demographic characteristics, the usage behavior of the PRS showed a difference regarding the purpose of using the service in the categories of gender and major field of study. Furthermore, users were concerned with various components of the PRS such as ease of use, design, relevance of content, user support, and interactivity. Conclusions: We suggest reinforcing user education degree and promotion to enhance the PRS. Since users were concerned with ease of use, design, relevance, user support, and interactivity, we recommend these as major points for improvement.

Practical applications of CsPbX3 nanocrystals (NCs) are limited by their poor stability. The formation of heterojunction between CsPbX3 NCs and oxides is an effective means to protect perovskite from polar solvents and other external factors. Significantly improving the stability and photocatalytic properties of the core/shell perovskite is very important for its application in photoelectric and photocatalytic technology. Here, we report the synthesis of asymmetrical CsPbBr3/TiO2 core-shell heterostructure NCs at single particle level by hot injection liquid phase synthesis and sol-gel method, where each CsPbBr3 NCs is partially covered by titanium dioxide. It is shown that the type II arrangement is generated at the heterogeneous interface, which greatly facilitates the separation of electron-hole pairs and increases the carrier transport efficiency. More crucial, due to the protection of titanium dioxide shell, the product has higher long-term stability in humid air compared with bare CsPbBr3 NCs. The asymmetrical core-shell heterostructure prepared in this study not only improves the stability of CsPbX3 NCs, but also provides some ideas for optoelectronic device applications and TiO2-based photocatalysts.

The aim of this work is to study the phase transformations, microstructures and mechanical properties of the martensitic stainless steel (MSS) 410 deposits produced by laser powder-directed energy deposition (LP-DED) additive manufacturing. The LP-DED MSS 410 deposits underwent the post heat treatment in austenitizing at 980℃ for 3hrs and followed by different tempering treatment at the temperatures of 250, 600, and 750℃ for 5hrs, respectively. The analyses of phase transformations and microstructural evolutions of LP-DED MSS 410 were carried out using X-ray diffraction, SEM-EDS, and EBSD. Vickers hardness and tensile strength properties were also measured to analyze the effects of the different tempering heat treatments. It reveals that as-built MSS 410 has very fine lath martensite and high hardness of about 480HV1.0 and tensile strength of about 1280 MPa, but elongation was very lower than the post heat treated ones. Precipitations of chromium carbide (Cr23C6) were most commonly observed at the grain boundaries and the entire matrix at the tempering temperatures of 600℃ and 750℃. In general, the tensile strengths de-creased from 1381MPa to 688MPa as tempering temperatures increased up to 750℃ from 250℃. Additionally, as the tempering temperature increased, the chromium carbide and tempered mar-tensite structures became coarser.

Several types of guided bone regeneration materials are available with various properties and clinical indications. Among them, dentin-derived matrix from extracted teeth is an excellent alternative to traditional graft materials, such as allografts and xenografts. Different clinical preparation protocols exist: block form versus powder form, demineralized versus non-demineralized form. Out of these methods, demineralization protocols for dentin-derived matrix from extracted teeth have been noted for a wide range of successful clinical outcomes. The purpose of this animal study was to find out the most effective method of demineralizing dentin-derived matrix to result in the highest regenerative ability in the bone graft material in rabbit calvaria. The study conducted a comparative histomorphometric analysis of four groups in distinguished matrix conditions: a control group without graft placement, a non-demineralized dentin-derived matrix graft placement group, a 15-minute demineralized dentin-derived matrix graft placement group, and a 30-minute demineralized dentin-derived matrix graft placement group. Regenerative processes were evaluated three times at 2, 4, and 8 weeks post-graft placement. These groups of rabbits were evaluated randomly in a blinded setting to prevent bias. Among the four groups compared, the group with a 15-minute demineralized dentin-derived matrix graft showed the most efficient bone regeneration in the histomorphometric analysis. Based on this animal study, it was apparent that a 15-minute demineralization of dentin-derived matrix is the preferred preparation protocol to maximize the regenerative potential in the matrix.

This paper discovers that current variational principle and Noether theorem for different physics systems with (in)finite freedom systems have missed the double extremum processes of the general extremum functional that both is deduced by variational principle and is necessarily taken in deducing all the physics laws, but these have not been corrected for over a century since Noether's proposing her famous theorem, which result in the crisis deducing relevant mathematical laws and all physics laws. This paper discovers there is the hidden logic cycle that one assumes Euler-Lagrange equations, and then he finally deduces Euler-Lagrange equations via the equivalent relation in the whole processes in all relevant current references. This paper corrects the current key mistakes that when physics systems choose the variational extreme values, the appearing processes of the physics systems are real physics processes, otherwise, are virtual processes in all current articles, reviews and (text)books. The real physics should be after choosing the variational extreme values of physics systems, the general extremum functional of the physics systems needs to further choose the minimum absolute extremum zero of the general extremum functional, otherwise, the appearing processes of physics systems are still virtual processes. Using the double extremum processes of the general extremum functionals, the crisis and the hidden logic cycle in current variational principle and current Noether theorem are solved. Furthermore, the new mathematical and physical double extremum processes and their new mathematical pictures and physics for (in)finite freedom systems are discovered. This paper gives both general variational principle and general Noether theorem as well as their classical and quantum new physics, which would rewrite all relevant current different branches of science, as key tools of studying and processing them.

Despite UAV multi-target detection exhibits considerable developmental potential worldwide, it suffers distinct challenges compared with traditional tasks in this field. These challenges include insufficient feature extraction capabilities for small targets, limited capabilities for multi-dimensional feature fusion, as well as constraints on hardware computation parameters. Especially in mission scenarios such as disaster detection, these challenges will be further amplified. Consequently, this paper introduces SSE-YOLO, an innovative YOLO framework algorithm specially designed to address these challenges. To enhance the model's feature extraction capability, we employ the SPDConv module to replace the original Conv in the backbone section, utilizing depth-separable convolution instead of traditional convolution pooling. Concurrently, we eliminate the SPPF module at the bottom and address a new Separate Kernel Attention Pyramid Pooling (SKAPP) module, substantially enhancing the feature fusion capability at the model's core. Moreover, to address the challenge of multi-dimensional feature fusion, we replace the Concat module of the neck and head with E-BiFPN, transmitting feature information from the backbone to the lower network through four CBS blocks, which effectively resolves the issue of lost contextual information in the model. Meanwhile, SSE-YOLO undergoes ablation experiments on the VisDrone2019 dataset to evaluate its effectiveness against alternative methods, and experimental results illustrate the model's exceptional precision in detecting UAV targets. In comparison to models with comparable experimental accuracy, SSE-YOLO requires remarkably fewer parameters. On the VisDrone2019-DET-test-dev dataset, SSE-YOLO enhances mAP by 17.3%, with a 42.5% reduction in the parameter amounts. Therefore, the proposed method effectively tackles the challenge of reconciling low parameters and high accuracy, presenting a novel pathway for deep learning-based UAV multi-target detection.

The 2019 novel coronavirus (2019-nCoV) causes novel coronavirus pneumonia (NCP). Given that approved drug repurposing becomes a common strategy to quickly find antiviral treatments, a collection of FDA-approved drugs can be powerful resources for new anti-NCP indication discoveries. In addition to synthetic compounds, Chinese Patent Drugs (CPD), also play a key role in the treatment of virus related infections diseases in China. Here we compiled major components from 38 CPDs that are commonly used in the respiratory diseases and docked them against two drug targets, ACE2 receptor and viral main protease. According to our docking screening, 10 antiviral components, including hesperidin, saikosaponin A, rutin, corosolic acid, verbascoside, baicalin, glycyrrhizin, mulberroside A, cynaroside, and bilirubin, can directly bind to both host cell target ACE2 receptor and viral target main protease. In combination of the docking results, the natural abundance of the substances, and botanical knowledge, we proposed that artemisinin, rutin, glycyrrhizin, cholic acid, hyodeoxycholic acid, puerarin, oleanic acid, andrographolide, matrine, codeine, morphine, chlorogenic acid, and baicalin (or Yinhuang Injection containing chlorogenic acid and baicalin) might be of value for clinical trials during a 2019-nCov outbreak.

A total internal reflection photonic crystal fiber (PCF) based on hexagonal core is proposed for gas sensing in a specific wavelength range. The higher sensitivity and lower confinement loss were realized by the structure of the proposed PCF consists of two layers with circular holes rotated hexagonally around a core region and six slotted air-hole in the cladding based on numerical analysis. The simulation results show that the enhancement of the relative sensitivity has been done by enhancing the diameter of the hexagonal shape air-hole cladding (d1) and the hexagonal arranged holes around the central solid core (d0) in this design. Also, the confinement loss has been reduced by enhancing the ratio of length to width of slotted holes (l/w) and decreasing the cladding air-hole diameters (d1). As the refractive index increases, the wavelength shifts toward the long wavelength. And in a certain temperature range, the transmission characteristics of the device does not change with the temperature. The results are helpful for designing high performance PCF for gas sensing applications.

This paper discovers that current canonical variational principle and canonical Noether theorem of (in)finite freedom systems for different physics systems have neglected doublet extreme value processes of the general extreme value functional that both is derived by variational principle and is necessarily be taken in deriving all ( quantum ) physics laws in phase space, but which have not been done for over one century since Noether's showing her distinguished theorem, which lead to the crisis deriving all (quantum) physics laws (necessary) in phase space. We discover there is the hidden logic cycle that people assume canonical equations, and then they finally deduce canonical equations by the equivalent relation in the whole processes in all current references. We correct the current key mistake concepts that when physics systems take the variational extreme values, the appearing processes of the physics systems are real physics processes, otherwise, are virtual processes in all current references. The real physics should be what after taking the physics systems' variational extreme values, the physics systems' general extremum functional needs to further take the general extremum functional's minimum absolute extremum zero, otherwise, the appearing processes of physics systems still are virtual processes. Conservation current equations and conservation currents, in phase space, of general canonical variational principle and general canonical Noether theorem are, respectively, deduced for the first time. Using the general extremum functionals' doublet extreme value processes, the hidden logic cycle and the crisis in current canonical variational principle and current canonical Noether theorem are solved. Consequently, the new mathematical pictures, classical and quantum new physics in phase space and the new mathematical and physical doublet extremum processes for (in)finite freedom systems are discovered. General canonical variational principle and general canonical Noether theorem naturally are given, which would rewrite all the different sciences in phase space, as key tools of studying and dealing with them.

Cement-free concrete has superior physical performance, such as strength and durability, compared to OPC concrete, however, it has the disadvantage of large shrinkage. Large shrinkage can cause cracks due to shrinkage stress in the long term. In this study, a shrinkage reducing agent (SRA) was used to reduce the shrinkage of cement-free mortar; its content was increased from 0.0 to 1.5 %. For an SRA content of 1.0 %, a calcium sulfoaluminate (CSA) expansive additive (EA) (2.5, 5.0, and 7.5%) was added. To calculate the shrinkage stress of cement-free mortar using the SRA and EA, the compressive strength, elastic modulus, and total and autogenous shrinkage were measured. The unit shrinkage stress of cement-free mortar was obtained by multiplying the elastic modulus by the length change and accumulated to obtain the shrinkage stress acting on the mortar according to the age. The shrinkage stress of cement-free mortar showed different tendencies as the age increased. At early ages, the shrinkage rate of the mortar occupied a large proportion of the shrinkage stress. In the long term, the shrinkage stress was significantly affected by the elastic modulus. As a result, SRA was found to be effective in reducing the shrinkage stress by decreasing both the elastic modulus and shrinkage. However, EA increased the shrinkage stress over the long term due to an increase in elastic modulus even though it compensated for early-ages shrinkage.

This paper studies a model of dynamic compensation and capital structure with managerial traits. We show that Optimistic manager perceives equity as more undervalued than debt, while, confident manager perceives debt as more undervalued than equity. Managerial risk aversion mitigates manager’s bias. The risk aversion of the optimistic manager has a convex effect on the optimal coupon. There exists the level of risk aversion eliminating the bias on the leverage. The managerial optimist has an ambiguous effect on the owner’s bankruptcy level. The risk aversion has a convex effect on the owner’s bankruptcy level. The optimistic/confident manager underestimates the credit spread. The risk aversion has convex effect on the credit spread. In contrast to rational manager, the optimistic/confident manger has higher level of effort. The risk aversion has a negative effect on the effort.

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

This paper introduces an alternative method to design the path following controller of an under-actuated spherical mobile robot, which has a single pendulum structure its inside as a driving mechanism. The mechanism has an under-actuated problem; two inputs for the roll and pitch but no direct input for the yaw. In order to overcome this problem, the proposed method defines a virtual reference input for the heading direction. The virtual reference input works as a control input since it can be arbitrarily designed just like the reference input of a conventional system. The control scheme using the defined virtual reference input achieves the stabilization and path following control of the under-actuated spherical mobile robot without any additional control technique. The stability of the proposed control scheme is guaranteed by Lyapunov stability analysis, and simulation results are given to demonstrate its performance.

Beta-carotene is a fat-soluble antioxidant commonly found in foods such as fruits, vegetables, and palm oil. Despite various liquid chromatography methods are proposed to detect and measure the sera carotenoid level, a long retention time to elute this marker is needed. This study attempted to develop a rapid reverse phase method in eluding beta-carotene in human sera. The researchers managed to elute the antioxidant in 2.2 minutes by applying a combination of a C8 column, mobile phase comprising of acetonitrile mixed with methanol in 70:30 proportion, and an ultra-high performance liquid chromatography system. The outputs had a good calibration curve (R²=0.959) and low coefficient of variation (0.2%), suggesting this protocol is reliable. A column with a lower carbon chain such as C8 allows the beta-carotene molecule to flow through the column faster. Besides, selecting solvents with high elution strength coupled with an ultra-high performance liquid chromatography system which equipped with high pressure can force the beta-carotene through the column in a shorter duration compared to previous reported methods. Therefore, it is recommended to adopt this protocol in epidemiological studies where beta-carotene is screened as a dietary biomarker associated with disease of interest by using human sera in the population level.

Decapod assemblages in Zostera marina beds from two bays adjacent to unvegetated habitats were investigated to assess their influence on decapod assemblages. Thirty-eight decapod species belonging to 4 taxa were collected using a small beam trawl at four habitat types from two different locations off the coast of Namhae Island, southern Korea. Dominant decapod taxon at all habitats was the caridean shrimps, with Eualus leptognathus, Heptacarpus pandaloides, Latreutes anoplonyx, La. laminirostris and Palaemon macrodactylus being the most abundant caridean species. Crabs were characterized by the highest biomass, but moderate species richness and abundance. Penaeoids and sergestoids shrimps only accounted for <1% of the total decapod abundance. The number of species, their abundance, and the diversity of decapod assemblages varied greatly by habitat type, season, and diel patterns. Species number and abundance peaked in seagrass beds of southern exposed bays during the autumn, and were lowest in unvegetated habitats during the summer months. Diel decapod species and catch rates were higher at night. Dense seagrass vegetation and nighttime supported greater decapod species richness and higher mean densities, but not diversity. Multivariate analyses revealed that habitat type and season significantly affected the structure of decapod assemblages, but diel patterns had a minor influence. Among decapod species, Pa. macrodactylus and Pugettia quadridens characterized the decapod assemblages in seagrass beds at the northern semi-closed bay, while Telmessus acutidens, Crangon affinis, Cr. hakodatei, Charybdis japonica and Portunus sanguinolentus were significantly associated with both vegetated and unvegetated habitats at the southern exposed bay, with the former two species more abundant during winter and spring.

Face routing has been adopted in wireless sensor networks (WSNs) where topological changes occur frequently or maintaining full network information is difficult. For message forwarding in networks, a planar graph is used to prevent looping, and because long edges are removed by planarization and the resulting planar graph is composed of short edges, messages are forwarded along multiple nodes connected by them even though they can be forwarded directly. To solve this, face routing using information on all nodes within 2-hop range was adopted to forward messages directly to the farthest node within radio range. However, as the density of the nodes increases, network performance plunges because message transfer nodes receive and process increased node information. To deal with this problem, we propose a new face routing using the planar graphs of neighboring nodes to improve transfer efficiency. It forwards a message directly to the farthest neighbor and reduces loads and processing time by distributing network graph construction and planarization to the neighbors. It also decreases the amount of location information to be transmitted by sending information on the planar graph nodes rather than on all neighboring nodes. Simulation results show that it significantly improves transfer efficiency.

It has been well known that the exponential distribution is the only continuous distribution that has the memoryless property. Here, we observe that, if the exponential distribution dominates an economy as a probability distribution of income acquisition, then the memoryless property imposes equal opportunities on agents in this economy to acquire earnings. Based on this observation, we propose to identify the emergence of an exponential income distribution as a potential necessary condition for guaranteeing the equality of opportunity. Together with other conditions (such as social and economic mobility), it would promote equal opportunities for income acquisition among citizens. Empirically, we employ the latest data available from four representative market-economy countries (the United Kingdom, the United States, Canada, and China) to demonstrate that the exponential distribution is a stylized feature of the income structure of the low- and middle-income class, which occupies the great majority of populations. By contrast, the top income classes in these countries obey the Pareto distribution. To validate the relationship between exponential distribution and equal opportunity, we empirically show how the income structure of the low- and middle-income class in China (from 1978 to 2015) evolved towards an exponential distribution after the market-oriented economic reformation.

In accordance with regulations set forth by the Ministry of Land, Infrastructure, and Transport in Korea regarding the "Flame Retardant Performance of Building Finishing Materials and Fire Spread Prevention Structure," it is mandated that semi-noncombustible materials have a total heat emission less than 8 MJ/m². Consequently, our study aimed to determine the ideal quantity of flame-retardant treatment required to meet the fire safety standards for Korean larch and Japanese cedar, commonly used exterior materials in Korean construction. To this end, we investigated using a cone calorimeter to observe changes in the THR (Total Heat Released) based on the AFI (Amount of Flame-retardant Impregnation) in Korean larch and Japanese cedar. Our findings indicated that the AFI needed to satisfy the prescribed flame-retardant standard of 8 MJ/m² was THR 299 MJ/m² for Korean larch and THR 526 MJ/m² for Japanese cedar. As a result, we established optimal impregnation levels of flame retardant for both species.

The spring-in phenomenon of the composite parts can affect the assembly process. This study aims to predict the spring-in phenomenon of carbon fiber reinforced plastic (CFRP) part. Here, we predict the spring-in of the CFRP part using a coupled analysis of the forming and cooling processes during the stamping process. First, a simulation of the entire forming process, such as the transfer of the composite laminate, gravity analysis, and forming was performed to obtain the temperature distribution of the CFRP part. Subsequently, a finite-element (FE) simulation of the cooling process was conducted to predict the spring-in phenomenon of the shaped CFRP part using the temperature data obtained in the forming simulation. Finally, a CFRP part was manufactured and compared with the results of the FE simulation.

Although there are a large number of databases available for regulatory elements, bottleneck has been created by the lack of bioinformatics tools for predicting types of mechanisms underlying actions of regulatory elements. To reduce the gap, we developed ARabidopsis Transcription regulatory Factor Domain-domain interaction Analysis Tool- Liquid-liquid phase separation (LLPS), Oligomerization, GO analysis (ART FounDATion-LOG), a useful toolkit for protein-nucleic acid interactions (PNI) and protein-protein interactions (PPI) analysis based on domain-domain interaction (DDI). LLPS, protein oligomerization, structural properties of protein domains, and protein modifications are major components in orchestrating spatio-temporal dynamics of PPI and PNI. Our goal is to integrate PPI/PNI information into development of prediction model for identifying important genetic variants in peach. The program unified inter-database relational keys by protein domains for facilitating inference from the model species. Key advantage of the program lies in the integrated information of related features: LOG, structural characterization of domain (e.g. domain linker, intrinsically disordered regions, DDI, domain-motif (peptide) interaction, beta-sheet and transmembrane helices), and post-translational modification. We provided simple tests to demonstrate how to use the program. The program may be applied to other eukaryotic organisms. The program codes and data are freely available for download at and https://sourceforge.net/projects/artfoundation-log/.

The synergistic efficacy of combined treatment mild heat (MH) and dielectric barrier discharge (DBD) plasma in Bacillus cereus-contaminated red pepper powder was tested. A cocktail of three strains of B. cereus (NCCP 10623, NCCP 14579, ATCC 11778) was inoculated onto red pepper powder and then treated with MH (60 ℃ for 5-20 min) and DBD plasma (5-20 min). Treatment with MH and DBD plasma alone for 5~20 min resulted in reductions of 0.23~1.43 and 0.12~0.96 log CFU/g, respectively. Combined treatment with MH and DBD plasma was the most effective at reducing B. cereus counts on red pepper powder and resulted in log-reductions of ≥ 6.0 log CFU/g. The largest synergistic values (4.24-4.42 log) against B. cereus in red pepper powder were obtained by the combination of 20 min MH and 5~15 min DBD plasma. Hunter color ‘‘L’’, ‘‘a’’, and ‘‘b’’ values of the combination-treated samples were not significantly different from those of non-treated samples. Also, no significant (p > 0.05) differences in pH values between samples were observed. Therefore, these results suggest that the combination of MH treatment and DBD plasma can be potentially utilized in the food industry to effectively inactivate B. cereus without incurring quality deterioration of red pepper powder.

Many studies on flexible strain and pressure sensors have been reported due to growing interest in wearable devices for healthcare. However, most are fabricated with multiple ingredients and complicated methods even though commercial textiles, such as cotton, nylon, polyester, and silk were used. Here we present flexible pressure and strain (motion) sensors prepared with only graphene oxide (GO) and commercial silk fabrics and yarns. The pressure sensors were fabricated by simply dipping the silk fabric into GO solution followed by thermal treatment at 400 °C for reduction of GO (rGO). The pressure sensors were made from rGO-coated fabrics, which were stacked in 3-, 5-, and 7-layers. The super-sensitivity of 2.58 ×103 kPa-1 at low pressure was observed in the 7-layer pressure sensor. The strain sensors were obtained from rGO-coated twisted silk yarns whose gauge factor was 0.307. Although this value is small or comparable to other sensors, it is appropriate for motion sensing. The results of this study show a cost-effective and simple method for the fabrication of pressure and motion sensors with commercial silk and GO.

Background/Objectives: This study aims to investigate the influence of root canal morphology and various treatment variables on the outcomes of root canal treatments (RCT) in mandibular second molars, assessed through cone-beam computed tomography (CBCT) imaging. Methods: A total of 150 CBCT images were examined, comprising 100 cases of persistent endodontic infections and 50 from previously treated root canals with normal apices in mandibular second molars. CBCT was utilized to evaluate root canal configuration, the radiographic quality of coronal restorations and treated canal systems, and the presence of periapical lesions. Statistical analyses were performed to explore correlations between these factors. Results: The presence of a C-shaped root canal configuration did not demonstrate a significant correlation with periapical lesions (p=0.05). Factors influencing endodontic treatment outcomes included the presence of missing canals (p=0.018), underfilling or overfilling (p=0.045), and inadequate coronal restoration (p=0.006). The presence of a missing canal was identified as the variable most significantly associated with periapical lesions (OR=3.103). Leaky canals were more commonly observed in C-shaped root canals (p&lt;0.001). Conclusions: Regardless of the root canal morphology of mandibular second molars, successful RCT depends on thorough disinfection to eliminate any untreated canals, precise three-dimensional filling of the canals at the correct working length, and a securely sealed coronal restoration to prevent leakage.

Background and Objectives: The arthroscopic biceps rerouting (BR) technique was introduced as a novel technique for large-to-massive rotator cuff tears (LMRCT). This method can restore shoulder stability, and its biomechanical effect was verified in a cadaver experiment. Recent reports have shown favourable clinical outcomes. This study aimed to compare the clinical outcomes of partial repair with those of BR technique in LMRCT. Materials and Methods: We included 72 patients who had undergone LMRCT. Arthroscopic partial repair was performed in 31 patients (group I), while repair with the BR technique was performed in 41 patients (group II). Functional and imaging outcomes were evaluated and compared using a visual analogue scale for pain, range of motion (ROM), American Shoulder and Elbow Surgeons (ASES) score, Constant score, and Korean Shoulder Score (KSS) before the surgery and at 3, 6, and 12 months after the surgery and at the last follow-up. Tendon integrity was investigated using magnetic resonance in all the patients at 12 months postoperative. Results: Mean follow-up period was 22.11 ± 10.47 months (range, 12–53 months). Forward flexion (P=0.02) and external rotation at the side (P=0.04) were significantly higher in group II than in group I on postoperative day (POD) 12. For internal rotation, group II showed significant improvement compared to group I on POD 3 (P=0.002) and at six months postoperative (P=0.01). On POD 12, the ASES (P=0.047) and KSS (P=0.048) were better in group II. Significant improvements in pain and clinical scores were observed in both groups at the last follow-up. However, there were no significant differences in pain, clinical scores, or ROM between the two groups at the last follow-up. Retear of the repaired tendon was observed in nine patients in group I (29.03%) and 8 in group II (19.51%, P = 0.35). Conclusions: Partial repair and repair using the BR technique effectively improved clinical and radiologic outcomes. The BR technique revealed early recovery of ROM and better clinical results than partial repair until one year postoperatively. This could be a useful method in LMRCT.

The blended perfluorinated sulfonic acid ionomers are prepared to have equivalent weight (EW) ~1000, 980, and 830. The catalyst layers (CLs) using blended PFSA ionomers with different side chain lengths and EWs are investigated, compared to the CLs utilizing single ionomers. The IEC results indicate that the blended ionomers have the targeted EWs. As a result, it is found that the blended ionomers exhibit higher ion conductivity than the single ionomers at all temperatures due to higher water uptake of the blended ionomers. Even though they have a similar EW, it implies that the blended ionomers have bulk structure to form competent free volume. The blended ionomers with short side chain (SSC) and low EW can help reduce the activation energy due to the enhanced hydrophobic and hydrophilic segregation. In addition, it is observed that the catalyst layers using the blended ionomer form more porous microstructure to help reduce the resistance of oxygen transport and attributes to lower mass transfer loss. This effect is significantly revealed in the fuel cell operation at not the lower temperature (70 °C) and full humidification (100%) but the elevated temperature (80 °C) and lower relative humidity (50 and 75%). The blended ionomer-based catalyst layers with higher water uptake and porous CL structure result in higher fuel cell performance and better mass transport than the single ionomer-based catalyst layers.

South Korea proposed reducing greenhouse gas emissions by 37% compared to the expected emissions by 2030 as the POST-2020 greenhouse gas reduction target. Electric vehicle distribution in the public sector is essential to achieve the carbon dioxide reduction target for transportation. In particular, when buses with internal combustion engines, which travel long distances and contribute substantially to greenhouse gas emissions, are replaced with electric buses, it is expected that greenhouse gas emissions will be significantly reduced. There are three types of electric buses with different power supply systems: a plug-in type in which power is supplied when a plug is inserted, a battery-swapping type in which a battery mounted on top of the vehicle is swapped at a swapping station, and a wireless type in which the battery is wirelessly charged through self-induction at a charging facility installed on the road. Vehicles of each charging type have different advantages and disadvantages. The performance, charging type, battery capacity, and operating environment of electric buses are mutually related parameters that must be considered when introducing such vehicles. Therefore, the optimal charging type must be selected according to the operating environment to enable the widespread use of electric buses. As such, this report proposes the optimal charging type according to the operating environment of public-sector electric vehicles.

Background: Particulate matter and urban air pollution affect the human body and can lead to death. Epidemiological studies should consider the exposure to pollutants and the diverse responses of individuals depending on their sensitivity to the pollutants. Methods: In this study, air pollution measurements were obtained hourly at measuring stations operated by the national and local governments to increase the reliability of the measured values. A β-ray absorption method was used to analyze the measurements of fine dust and determine the particulate matter content. Results: The air pollution data were log-converted to enable the comparison of data from different time periods. The comparison was made, focusing on the period of Seoul's fine dust policy. As a result, the cancer incidence rate also decreased after the policy. The data on individual characteristics were obtained from a survey of Seoul citizens conducted from 2015 to 2016 and using indicators such as the quality of life and social trust of Seoul citizens. Concludions: The survey on the living environment and residence indicated that 80% of the heads of households were men. Women had a greater dissatisfaction than men with the residential, economic, and social environments. The survey questions on well-being were related to the internal and external environment such as air pollution, noise, and fine dust.

The Meissner effect is a special property of superconductors. In this paper, based on the characteristics of the Meissner effect, a superconducting phase transition model of a superconductor under a changing magnetic field is proposed. A thermodynamic analysis was performed on the model to calculate both the changes in the thermodynamic parameters of the superconductor during the phase transition and the changes in the overall work and energy of the model. For Model 1 in the present study, the thermodynamic energy of the superconductor was not conserved due to the phase change of the superconductor under a changing magnetic field.

The physics of Hubble's law, motivated by the anomalous acceleration of Pioneer 10/11, suggests that the Hubble constant corresponds to a gravitational field of the Universe. The Hubble constant inferred from Pioneer 10/11 data is $\sim 69$ km/s/Mpc. The anomalous acceleration of Pioneer 10/11 can be interpreted as an observational evidence for Mach's principle. The redshift is an apparent value. Its intrinsic value has a limit resulting to $v

Knowledge-intensive business services (KIBS) are professional services that create new added value by creating, accumulating, and disseminating new knowledge. When it comes to conducting business involving new technology, KIBS play the roles of innovator, user, and producer of new technology that has led to technological innovation. This study aimed to determine the role of KIBS as a tool for innovation in a country’s economic system. Specifically, the degree and role of their impact on the Korean economy were analyzed and compared for the entire KIBS sector, T-KIBS (a new technology-based professional service), P-KIBS (a traditional professional service), and every subsector. For this purpose, the demand-inducement model, supply inducement model, and interlinkage effects method were applied using the 2019 input-output table published in 2022. The analysis showed that the indirect production inducement effect of the entire KIBS industry on other industries was 0.800 KRW, the indirect added value inducement effect was 0.330 KRW, and the supply disruption effect was 1.144 KRW. For T-KIBS, the indirect production inducement effect was 0.687 KRW, the indirect added value inducement effect was 0.272 KRW, and the supply disruption effect was 0.730 KRW. For P-KIBS, the indirect production inducement effect was 1.472 KRW, the indirect added value inducement effect was 0.646 KRW, and the supply disruption effect was 2.657 KRW. Finally, regarding the economic ripple effect of the KIBS subsector, legal and management support services and advertisements corresponding to P-KIBS showed higher figures than the T-KIBS subsectors in all sectors, including production inducement, the added value inducement effect, and the supply disruption effect. These results revealed that in the South Korean economic system, KIBS contribute to production and value addition across all industrial sectors. It is apparent that the absence of supply significantly disrupts other industries. Furthermore, production inducement effects are evenly distributed among all the KIBS subsectors in the secondary and tertiary sectors, while the value-added effects have a greater impact on the tertiary sector. In terms of the supply shortage effects, the secondary sector experiences a more significant impact. This underscores the crucial role of KIBS in sustaining and enhancing overall economic activity in South Korea. This study is significant in that it not only investigated KIBS as an industry group using the advantages provided by industry linkage analysis but also examined and compared detailed subsectors, thereby elaborately evaluating the influence relationship between KIBS and other industries. Therefore, the results presented in this study are expected to be useful for fostering the KIBS industrial sector and establishing economic innovation policies using KIBS.

Static and dynamic analysis of website security risks is generally used for website security meas-urements. The website security measurements method recently proposed includes similarity hash-based website security risk analysis and machine learning-based website security risk anal-ysis. In this study, a method that can be performed through information disclosed on the Internet was proposed to measure the risk of a website. DNS information, IP information, and website history information are required to measure the risk of a website. In addition, global traffic rank-ing, malicious code distribution history, and HTTP access status can be checked in the website history information. In this study, information related to the security risk of websites in a total of 2,000 domains was collected and analyzed in 1,000 normal and malicious domains. Through the experiment results, 11 open information collection items were selected to measure the security risk of the website. This study presented the possibility of using public information collection to measure website security risk.

For the elimination of radio-frequency interference (RFI) in a passive microwave radiometer, the threshold level is generally calculated from the mean value and standard deviation. However, a serious problem that can arise is an error in the retrieved brightness temperature from a higher threshold level owing to the presence of RFI. In this paper, we propose a method to detect and mitigate RFI contamination using the threshold level from statistical criteria based on a spectrogram technique. Mean and skewness spectrograms are created from a brightness temperature spectrogram by shifting the 2-D window to discriminate the form of the symmetric distribution as a natural thermal emission signal. From the remaining bins of the mean spectrogram eliminated by RFI-flagged bins in the skewness spectrogram for data captured at 0.1-s intervals, two distribution sides are identically created from the left side of the distribution by changing the standard position of the distribution. Simultaneously, kurtosis calculations from these bins for each symmetric distribution are repeatedly performed to determine the retrieved brightness temperature corresponding to the closest kurtosis value of three. The performance is evaluated using experimental data, and the error in the retrieved brightness temperature is observed to be less than approximately 3 K from a window with a size of 100 × 100 time-frequency bins according to the RFI levels and cases.

The microbiota of human breast milk (HBM) contributes to infant gut colonization; however, whether bacterial extracellular vesicles (EVs) are present in HBM or might contribute to this process remains unknown. In the present study, we characterized the HBM microbiota of healthy Korean mothers and measured the key bacteria likely affecting infant gut colonization by analyzing both the microbiota and bacterial EVs. A total of 22 HBM samples were collected from lactating mothers. The DNA of bacteria and bacteria-derived EVs was extracted from each sample. Gene analysis was performed using Illumina MiSeq. Firmicutes accounted for the largest portion among the phyla, followed by Proteobacteria, Bacteroides, and Actinobacteria in both bacteria and bacterial EV samples. At the genus level, Streptococcus (25.1%) and Staphylococcus (10.7%) were predominant in bacterial samples, whereas Bacteroides (9.1%), Acinetobacter (6.9%), and Lactobacillaceae(f) (5.5%) were prevalent in bacterial EV samples. Several genera including Bifidobacterium were significantly positively correlated between the two samples. Our findings reveal the diverse bacterial communities in HBM of healthy lactating mothers and suggest the presence of key bacteria with metabolic activity in HBM and that EVs derived from these bacteria may contribute to the vertical transfer of gut microbiota from mother to infant.

This chapter aims to construct a relatively complete, universal, and highly reliable road surface state monitoring and perception system through the research of the A1 contact road reconstruction project of an international airport (hereinafter referred to as the “airport”). The system design is based on on-the-spot investigation, theoretical analysis, and engineering practice, using vibrating string type and resistive strain sensors as sensing means, real-time high-frequency signal acquisition technology as the guide, 4G router for wireless communication technology as the media, and storage technology for monitoring system based on server storage terminals. In combination with engineering background, aircraft motion state, main landing gear configuration, sensor selection and evaluation, and other major factors, the actual monitoring information needs of the plane are fully taken into account, as well as the difference in sensor information types, and the system design is carried out by stratification and classification.

In order to study the performance of a new type of cement-based grouting material under the coupling effect of freezing-thawing cycle and sulfate attack, experiments were designed and carried out. The damage mechanism of the material under the coupling effect of freezing-thawing and Na2SO4 solution was analyzed by measuring the mass change, relative dynamic elastic modulus, compressive strength loss and microstructure of the new grouting material. With increasing freeze-thaw cycles, mass loss and compres-sive strength loss of the sample in 15% Na2SO4 solution gradually increase, and the relative dynamic elastic modulus gradually decreases. During a 30-cycle freeze-thaw cycle, the mass loss rate, compressive strength loss rate, and relative dynamic elastic modulus of the sample are 4.17%, 24.59%, and 84.3%, respectively, showing good corrosion resistance and frost resistance durability. Microscopic analysis showed that SO42- caused the decomposition of C-S-H gel in the sample and the formation of Gypsum, and the widening of crack width aggravated the internal deterioration, indicating that the material deterioration rate increased under the dual-factor coupling effect.

Timely and accurate information on tree species is crucial for the sustainable management of natural resources, forest inventory, biodiversity detection, and carbon stock calculation. The advancement of remote sensing technology and artificial intelligence has facilitated the acquisition and analysis of remote sensing data, resulting in more precise and effective classification of tree species. Multimodal remote sensing data and deep learning seem to be the current tree species classification research mainstream, whether or not. The current review on the remote sensing data and deep learning tree species classification methods perspectives to analyze the unimodal and multimodal remote sensing data and classification methods in this realm is missing. To bridge the gap, we search for major trends in the remote sensing data and tree species classification methods, provide a detailed overview of classic deep learning-based methods for tree species classification, and discuss the limitations.

Liquid metal alloy, incorporated with microfluidic manipulation, has become a promising candidate for flexible resistive sensor array (RSA) that can imitate the functions of human skin. One advantage of RSA with shared rows and shared columns is to reduce the number of wires from M × N to M + N (rows: M and columns: N) and hence to greatly lessen the complexity and burden on the electrical system. The associated drawback is the crosstalk effect between adjacent elements during measurement. Although many literatures have reported several methods to resolve this limitation, almost all of them focus only on the high resistance value (≥100 Ω) RSA. There is a lack of detailed experimental data that addresses low resistance RSA with sensing elements below 100 Ω. Here, we aim to fill the gap of this field. We established two common RSA readout systems, i.e. zero potential methods (ZPM) (setting non-scanned-sampling-electrode zero potential (S-NSSE-ZP) and setting non-scanned-sampling-electrode zero potential with amplifier (S-NSSE-ZP-A)) and to compare their performances in low resistance value (≤100 Ω) RSA. For ideal resistor RSA, the measurement results show that S-NSSE-ZP has at least one time higher error than S-NSSE-ZP-A.

Hematopoietic stem cells (HSCs) are responsible for the production of blood cells throughout the human life span. Single HSCs can give rise to at least eight distinct blood cell lineages. Together, hematopoiesis, erythropoiesis and angiogenesis coordinate several biological processes, such as cellular interactions in development and proliferation, guided migration, lineage programming and reprogramming by transcription factors. Any dysregulation of these processes may result in hematological disorders and/or malignancies. Several studies of the molecular mechanisms governing HSC maintenance have demonstrated that protein regulation by the ubiquitin proteasomal pathway is crucial for normal HSC function. Recent studies have shown that the reversal of ubiquitination by deubiquitinating enzymes (DUBs) plays an equally important role in hematopoiesis; however, there is only limited additional information regarding the biological function of DUBs. In this review, we focus on recent discoveries that have led to a better understanding of the physiological roles of DUBs in hematopoiesis, erythropoiesis and angiogenesis. In addition, we discuss the DUBs associated with common hematological disorders and malignancies, which may potentially be therapeutic drug targets.