Wind power generation is one of the mainstream renewable energy resources. Voltage stability is as important as the frequency stability of a power system with a high penetration of wind power generation. The advantages of high-voltage direct current (HVDC) transmission systems become more significant with the increase of both installed capacity and transmission distance in offshore wind farms. Therefore, this study discusses about various voltage control methods for wind turbines and HVDC transmission systems. First, various voltage control methods of a wind farm were introduced, and they include QV control and voltage droop control. The reactive power of a wind turbine varies with active power, while the active power from each wind turbine may be different owing to wake effects. Thus, QV and voltage droop control with varying gain values were also discussed in this paper. Next, the voltage control methods for a HVDC transmission system, such as power factor control, voltage control, and Vac-Q control, are also summarized and tested in this study. When a three-phase short circuit fault occurs or a suddan reactive power load increases, the system voltage would drop immediately. Thus, various voltage control methods for wind turbines or HVDC can make the system's transient response more stable. Therefore, this study implemented the simulation scenarios, including a three-phase short circuit fault at the point of common coupling (PCC) or a sudden increase of reactive power load, and adopted various voltage control methods, which aims to verify whether additional voltage control methods are effective to improve the performance of transient voltage.

To further explore the bearing capacity and sustainable construction of vacuum drainage pipe (VDP) piles, field tests were carried out to compare and analyze the ultimate single pile bearing capacity, pile side friction and pile end resistance of ordinary piles and vacuum drainage pipe piles. The effect of the VDP pile on energy conservation and emission reduction in practical projects is discussed. The results shows that the VDP pile basically eliminated the soil squeeze and did not cause excessive relative displacement of pile and soil after vacuum consolidation. The VDP pile enhances pile side friction resistance, resulting in a 17.6% increase in ultimate bearing capacity compared to traditional piles. The VDP pile method can reduce carbon emissions by 31.4% compared to traditional methods. This study provides guidance for the production and design of VDP piles in the future and demonstrates their potential for energy conservation and emission reduction benefits compared to traditional methods.

Our results demonstrated that SWT stimulates osteoblastogenesis and increase the cell number of osteoblasts, suggesting positive regulatory effects on osteoblast differentiation. However, the effect of SWT on bone formation need further examination, since the expression of alp gene is downregulated. On the other hand, SWT appears to negatively regulate osteoclast differentiation and bone resorption, as number of osteoclasts and the expression of critical bone resorptive genes are all downregulated. Collectively, SWT might change the equilibrium of bone remodeling and increase the bone mass. Our data provided supportive evidences that this medicine formulation can be applied to treat osteoporosis or bone destructive diseases.

Chemotherapy treatment based on Cisplatin (CDDP) is established as the drug of choice for head and neck squamous cell carcinoma (HNSCC). Malignant tumors respond to microenvironment alteration through a dynamic balance of mitochondrial fission and fusion. HNSCC is known to have hypoxic conditions, yet the effects and underlying mechanisms of hypoxia on chemosensitivity and mitochondrial dynamics remain unclear. We found that hypoxia promoted mitochondrial fission and CDDP sensitivity in HNSCC cells. Importantly, Mff was shown to be correlated with chemosensitivity in clinical samples of HNSCC that underwent a hypoxic condition. Hypoxia-inducible factor 1 α-subunit (HIF-1α) dramatically increased Mff transcriptional expression and directly bound to Mff. Hypoxia enhanced the release of reactive oxygen species (ROS) and upregulated the expression of Mff via HIF-1α in HNSCC cells. ROS depletion in HNSCC cells attenuated HIF-1α, Mff expression, and mitochondrial fission. Moreover, a knockdown of Mff suppressed hypoxia-induced mitochondrial fission and decreased CDDP chemosensitivity in vivo and in vitro. Our findings revealed that the hypoxia-induced release of ROS promoted mitochondrial fission and CDDP chemosensitivity via the regulation of HIF-1α/Mff in HNSCC cells, indicating that Mff may serve as a new biomarker to predict neoadjuvant chemosensitivity in HNSCC patients

Domain walls were studied for permalloy wires with different depth trenches (500 nm wide, 30 nm thick, 7.5 µm long, the depth of the trench was 0, 4, 5, 8, 10, 12 and 15nm). Permalloy (Ni80Fe20) wires were fabricated by electron beam lithography and Ar ion milling. When the depth of trench is smaller than 12 nm, the switching field (Hs) is increasing with the deeper trench. However, the depth of trench is bigger than half depth of thickness, the Hs is decreasing with the deeper trench. We believed that Hs increased as the trench depth increased was because the magnetic diploes force increased between the magnetic poles on two sides of the trench. The domains of the wires were divided by the trenches and the domain walls were pinned on the trenches these were confirmed by magnetic force microscopy images.

Six Half-ring with varying linewidth from 120nm to 370nm were connected in series on five corners. The magnetization reversal processes were investigated by the measurement of anisotropic magnetoresistances (AMR). The number of switching jumps in the AMR loops, from zero to five, varied with the longitudinal applied field. These discrete jumps result from domain wall nucleating and depinning on the corners. The larger external field applied the fewer number of jumps in the MR curve. This reproducible and particular-respondence of domain wall device in pattern of half-ring wire might be the new promising magnetoelectronic devices.

Cymbidium faberi Rolfe is one of the traditional Chinese orchids with important ornamental value, and the cultivation of Cymbidium faberi Rolfe mutant strains with different appearances is essential to increase its economic value, but at present, the acquisition of Cymbidium faberi Rolfe mutant strains basically relies on natural mutation.The objectives of this research were to mutagenize Cymbidium faberi Rolfe protocorm-like bodies (PLBs) and shoots in vitro using sodium azide (NaN3), and to screen and evaluate mutants in mutagenized Cymbidium faberi Rolfe seedlings using morphological characteristics.Cymbidium faberi Rolfe PLBs and shoots were used as mutagenic materials, and co-cultivated in induced shoots growth medium with the addition of 0.0 (control), 0.5, 1.0, 1.5, 2.0, 2.5, 3.0 mg/L and 0.0 (control), 4.0, 5.0, 6.0, 7.0, 8.0, 9.0, and 10.0 mg/L NaN3 to induce the mutations, and the mortality rates of the PLBs and shoots were increased with the increase of the NaN3 concentration.At 14 d of co-cultivation, PLBs and shoots were most efficiently mutagenized with 1.5 mg/L and 4.0 mg/L NaN3, respectively.After the explants were cultured for 3 months, changes in leaf and flower morphology were observed in some mutants: shorter and thicker leaves, shorter node length, reduced height, and mid-translucent leaves compared with controls; and some Cymbidium faberi Rolfe bloomed prematurely, with single flowers with large, thick petal sepals and small inflorescences, and colours include light green throughout, and a few with purple stamens.This suggests that NaN3 can effectively mutagenise Cymbidium faberi Rolfe PLBs and shoots to satisfy people's demand for Cymbidium faberi Rolfe's ornamental properties while increasing its economic value.

Active films based on carboxymethyl chitosan incorporated corn peptide were developed. Physicochemical properties of the films, including thickness, opacity, moisture content, color, mechanical properties, water vapor permeability, and oil resistance, were measured. Biological activities of the films, including the antioxidant and antibacterial activities, were characterized in terms of 2, 2-diphenyl-1-picrylhydrazyl free radical scavenging activity, reducing power, the total antioxidant activity, and the filter disc inhibition zone method. The results indicated that the incorporation of corn peptide caused interactions between carboxymethyl chitosan and corn peptide in Maillard reaction and gave rise to the films light yellow appearance. Compared with the Control, the degree of glycosylation, browning intensity, thickness, opacity, tensile strength, antioxidant activity, and antibacterial activity of films were increased, but the elongation, vapor permeability, and oil resistance of films were decreased. The films based on corn peptide and carboxymethyl chitosan can potentially be applied to food packaging.

While modeling data in reality, uncertainties in both data (aleatoric) and model (epistemic) are not necessarily Gaussian. The uncertainties could appear with multimodality or any other particular forms which need to be captured. Gaussian mixture models (GMMs) are powerful tools that allow us to capture those features from a unknown density with a peculiar shape. Inspired by Fourier expansion, we propose a GMM model structure to decompose arbitrary unknown densities and prove the property of convergence. A simple learning method is introduced to learn GMMs through sampled datasets. We applied GMMs as well as our learning method to two classic neural network applications. The first one is learning encoder output of autoencoder as GMMs for handwritten digits images generation. The another one is learning gram matrices as GMMs for style-transfer algorithm. Comparing with the classic Expectation maximization (EM) algorithm, our method does not involve complex formulations and is capable of achieving applicable accuracy.

To compare The effects of organic and inorganic impregnation on the properties of unmodified, phenol formaldehyde oligomer-modified (PFOMCF), and sodium silicate-modified Chinese fir wood (SSMCF) were compared using samples prepared using the respiratory impregnation method. Impregnation and reinforcement effects and water resistance of PFOMCF and SSMCF were compared and the results was showed that the weight percentage gain, density increase rate, bending strength, and compressive strength of SSMCF were clearly higher than those of PFOMCF and had a lower water absorption rate within 60 h. The impregnation and reinforcement effects and dimensional stability of SSMCF were better than those of PFOMCF. FT-IR, XRD, CONE, and TGA examinations were used to test and analyze the chemical structure, crystalline structure, flame retardancy, and heat resistance of these modified woods. The results indicated that SSMCF possessed more hydrogen bonds than PFOMCF and that Si–O–Si chemical bonding with high bond energy was formed. Meanwhile, the weakened degree of the diffraction peak of SSMCF was much less than that of PFOMCF. These results explained that the mechanical properties and water resistance of SSMCF were better than PFOMCF. Compared with PFOMCF, SSMCF had a lower heat release rate (HRR), peak-HRR, mean-HRR, total heat release, smoke production rate, and total smoke production as well as higher thermal decomposition temperature and residual rate. Inorganic sodium silicate was shown to be a better flame retardant, while SSMCF had good smoke suppression effects, thermal stability, and safety performance in the case of fire.

Space tourism began in 2001 and became popular in 2021 because of commercial operations. With the development of space technology and commercialization, like re-launchable rockets to travel to space in recent years, it has gradually entered the era of space. However, the space industry causes massive emissions, inducing some opposition to its development. It is essential to investigate the attitude of residents toward space tourism and balance the pros and cons of sustainability. Quantitative analysis was adapted to test two models based on duality theory. The data were obtained from 284 samples from various regions of China and analyzed using the partial least squares structural equation modeling (PLS-SEM). The results show that the two-factor model of economic development conflicted with environmental protection. However, study two indicates that educational interventions can facilitate sustainable space tourism because they mediate the relationship between economic and environmental factors.

The flat terrain in plain areas makes the land easily accessible for cultivation and farming, providing vast opportunities for agricultural development. Additionally, these areas are crucial for urban construction and economic growth. Soil mapping plays a crucial role in understanding soil characteristics and guiding land management practices. However, accurately mapping soils in plain regions can be challenging due to their low spatial variability and diverse land use types. This study focuses on the impact of land cover changes on the accuracy of soil mapping in plain areas, aiming to provide effective assistance in soil mapping through the analysis of their coupling relationship. Starting with a 20-year land cover change analysis, this study utilizes a unified approach that combines expert knowledge, mixed sampling methods, and random forest mapping techniques. The study incorporates environmental covariates that have minimal period influence and synergistically use NDVI (Normalized Difference Vegetation Index) and land cover data from the same year. The analysis is based on transition matrices, confusion matrices, and their derived indicators. The research findings indicate that Tongzhou District has experienced rapid development over the past 20 years, with the area of construction land nearly doubling. 29% of arable land has been converted into construction land, resulting in an increase in the accuracy of the soil map from 58.99% to 66.91% over the 20-year period. The soil change area during this period accounts for 16.5% of the total area, with 51.9% of the changed areas overlapping with land cover change areas. These overlapping regions are predominantly influenced by human activities. In terms of cultivated land types in the study area, the quantity of arable land has decreased by approximately 29% over the 20 years, while the proportion of sandy loam calcareous fluvo-aquic soil and light loam calcareous fluvo-aquic soil, which constitute nearly half of the soil types, has increased. These data demonstrate the coupling relationship between land cover changes and soil type variations, particularly the significant influence of human activities on soil structure. It is evident that on one hand, improving the extent of land use in plain areas enhances the credibility of soil mapping. On the other hand, human activities impact land cover, which in turn affects and reflects changes in the soil.

In the context of inclusive education, digitalization in higher education is designed to promote the ideals of cultural diversity, social inclusivity, and sustainable development through technological means. This study explores the strategies and practices of digitalization in achieving inclusive education goals in higher education, aiming to provide theoretical and empirical foundations for education policymakers, teachers, and technology developers. This study adopts a mixed-methods research design, combining quantitative and qualitative data analysis to assess the current state of digitalization in higher education from various perspectives, particularly its effectiveness in advancing educational inclusivity. Through surveys, in-depth interviews, and case studies, data were collected from teachers, students, and administrative personnel to reveal opportunities and challenges in digital education resources and practices. The results show that while digitalization has improved the accessibility of educational resources, facilitated information sharing and cultural exchange, there are still numerous challenges, such as unequal technology access, insufficient cultural sensitivity in content, and issues related to the depth and quality of online interactions. Furthermore, the study identifies key factors supporting inclusive education, including cross-cultural curriculum design, teacher professional development, and students' critical use of digital tools. Finally, the paper presents a series of strategic recommendations, including the development of multicultural education platforms, strengthening teacher training, and building an inclusive digital environment. These recommendations aim to promote a more coordinated and inclusive higher education digital ecosystem that emphasizes not only technological innovation but also humanistic care and social responsibility. Through these measures, digitalization in higher education can better serve individual growth and comprehensive societal development.

In this paper we study a class of impulsive delayed neural networks with parameter uncertainties and reaction-diffusion terms. Using the properties of M-matrices and some inequality techniques, some sufficient conditions are derived to guarantee the global exponential stability of the given system. The results obtained are presented by simple algebraic inequalities, which are certainly more concise than previous methods. Finally, the validity and usefulness of our results are illustrated by arithmetic examples.

Seven pieces of Lacquer Lian from Warring States Period to Yuan Dynasty were analyzed by means of cross-section observation, Raman spectroscopy (RS) and thermally assisted hydrolysis and methylation pyrolysis coupled with gas chromatography/ mass spectroscopy (THM-Py-GC/MS). The results demonstrate that Lacquer Lian was consisted by three layers, including pigment layer, undercoat layer and ground layer, and lacquering techniques had undergone minimal changes from Warring States Period to Yuan Dynasty, the red mineral pigment was cinnabar, the lacquer sap was urushi. Furthermore, Boiled tung oil was found in the ground layer of lacquerwares from Song Dynasty and Yuan Dynasty.

In this paper, a Markov random field model is proposed to determine a site’s light pollution risk level. The specific data of 12 indicators of five typical cities in China is first collected to establish a hierarchical indicator system using an R-type clustering algorithm. Then, the entropy weight method is used to filter, determine 10-factor indicators, three potential impact indicators, and a light pollution risk index, and establish an undirected probability map model. A light pollution measurement based on Markov random field is obtained, and a location-based light pollution risk assessment index (LBLPRAI) is proposed. LBLPRAI of different types of sites is analyzed, and three possible intervention strategies are proposed to solve the light pollution problem: road lighting system planning, increasing vegetation coverage, and building system planning. Finally, the simulated annealing algorithm is used to determine the best intervention strategy, and it is concluded that the use of strategy 1 in the urban community 2 is the most effective measure, which can reduce the risk level of light pollution by 17.2%.

During the COVID-19 lockdown in Wuhan, transportation, industrial production and other human activities declined significantly, as did the NO2 concentration. In order to assess the relative contributions of different factors to reductions of air pollutants, sensitivity experiments were implemented by random forest (RF) model, with the comparison of contributions of meteorology, road traffic, and emission sources between different periods. Besides, an emulator was operated to suggest an appropriate limit for control of transportation. The RF models showed different mechanisms for air pollutants. Within-city Migration index (WMI) was more important in the normal, pre-lockdown and post-pandemic model while Out-Migration Index (OMI) was emphasized in the lockdown model. In the COVID-19 lockdown period, 73.3% of the reduction can be attributed to the decreased road traffic, showing massive impact of road traffic on the air quality. In the post-pandemic period, meteorology controlled about 42.2% of the decrease and emissions from industry and household controlled 40.0% while road traffic only contributed to 17.8%. It was suggested that priority of restriction should be given to road traffic within the city. A limit of less than 40% on the control of the road traffic can get a better effect, especially for cities with severe traffic pollution.

Accurate estimation of chlorophyll content in wheat leaves can not only reflect its growth and nutritional status, but also provide a scientific basis for field management. In order to evaluate the potential of hyperspectral data to estimate the chlorophyll content of wheat leaves, this study focused on the leaves of wheat at the flag-picking stage, flowering stage, grain filling stage and maturity stage. Based on the framework of five vegetation indexes, the spectral index was con-structed by using the combination of 400-1000nm bands, and the correlation between the con-structed spectral index and the measured chlorophyll value was analyzed, and the optimal spectral index was screened by the correlation coefficient. Based on the optimal spectral index, polynomial regression, random forest, decision tree and artificial neural network were used to establish the estimation model of chlorophyll value, and the optimal model for estimating the chlorophyll value of wheat leaves was selected through model evaluation. The results showed that the five optimal spectral indices at the four growth stages were mainly composed of red band, red edge band and near-infrared band, and the five optimal spectral indices at the grain filling stage had the highest correlation with the chlorophyll value, and the absolute value of the cor-relation coefficient was greater than 0.73, the accuracy of the estimation model established in the four growth stages was different, and the estimation accuracy of the flag stage was the best, with R² and RMSE of 0.79 and 2.63, respectively. The above results show that hyperspectral data is suitable for estimating the chlorophyll value of wheat leaves, and the PR model of flag picking period can be used as the optimal model for estimating the chlorophyll value of wheat leaves.

Background and Objectives: Angioembolization has emerged as an effective therapeutic approach for pelvic hemorrhages; however, its exact effect size remains uncertain. Therefore, we conducted this systematic review and meta-analysis to investigate the effect size of embolization-related pelvic complications after nonselective angioembolization compared to that after selective angioembolization in patients with pelvic injury accompanying hemorrhage. Materials and Methods Relevant articles were collected by searching the PubMed, EMBASE, and Cochrane databases until June 24, 2023. Meta-analyses were conducted using odds ratios (ORs) for binary outcomes. Quality assessment was conducted using the risk of bias tool in non-randomized studies of interventions. Results: Five studies examining 357 patients were included in the meta-analysis. Embolization-related pelvic complications did not significantly differ between patients with nonselective and selective angioembolization (OR 1.581, 95% confidence interval [CI] 0.592 to 4.225, I2 = 0%). However, in-hospital mortality was more likely to be higher in the nonselective group (OR 2.232, 95% CI 1.014 to 4.913, I2 = 0%) than in the selective group. In the quality assessment, two studies were found to have a moderate risk of bias, whereas two studies exhibited a serious risk of bias. Conclusions: Despite the favorable outcomes observed with nonselective angioembolization concerning embolization-related pelvic complications, determining the exact effect sizes was limited owing to the significant risk of bias and heterogeneity. Nonetheless, the low incidence of ischemic pelvic complications appears to be a promising result.

The outbreak of COVID-19 has brought unprecedented risks and challenges to everyone in the world. Myasthenia gravis is an autoimmune disease of the nervous system. Infection can worsen it and cause severe symptoms such as myasthenia crisis and respiratory failure. At present, the pandemic of COVID-19 may promote the aggravation of patients with MG. This article focuses on the respiratory management of MG patients during the epidemic of COVID-19.

The cutter structure and layout scheme of PDC (Polycrystalline Diamond Compact) bits are important factors in improving efficiency. To further improve the drilling efficiency of PDC bits, axe, triangular prism, and cylindrical PDC cutters were used as research objects. Based on the measured granite data, a finite element model of non-homogeneous granite was established and verified by uniaxial compression simulation. The rock-breaking process of different cutter combination schemes was compared using the finite element method, and the parameters in the best scheme were optimized using the Box-Behnken response surface method. The results show that the constructed model of non-homogeneous granite is consistent with the stress-strain relationship of real granite and is reliable. The axe PDC cutter is more aggressive than the other two cutters and is more suitable for the front row of the bit blade tooth arrangement, while the triangular prism cutter is the second most aggressive and is suitable for the rear row of tooth arrangement, and the best combination scheme is the front row of axe cutter and the rear row of triangular prism cutter arranged alternately with the axe cutter. The optimal transverse and longitudinal distances of the optimized triangular prism cutter from the front axe cutter are 10mm and 7mm, and the optimal transverse and longitudinal distances of the rear axe cutter from the front cutter are 10.06mm and 7mm. The drilling speed is more stable during drilling and the PDC bit with mixed tooth arrangement has 16.8% and 16.6% higher rate of penetration(ROP) compared with the bit with single axe cutter and triangular prism cutter, and the drilling speed is more stable during working, which can effectively improve the rock breaking efficiency of the PDC bit. The field application proves that the bit with mixed cutter arrangement is easier to break the complex formations, with more stable ROP and better efficiency. The study can provide theoretical support for the cutter layout of the PDC bit.

Sleep postures monitoring systems in the hospital aim at transforming sensing signals into quantitative data to characterize the sleep behaviors of the patient. However, a home-care sleep posture monitoring system needs to be user friendly. In this paper, we present iSleePost - a user-friendly home-care intelligent sleep posture monitoring system. We address the labor-intensive labeling issue of traditional machine learning approaches in the training phase. Our proposed mobile health (mHealth) system leverages the communications and computation capabilities of mobile phones for provisioning a continuous sleep posture monitoring service. Our experiments show that iSleePost can achieve 90 percent accuracy in recognizing sleep postures. More importantly, iSleePost demonstrates that an easily-wear wrist sensor can accurately quantify sleep postures.

Landing is one of the most dangerous tasks in all the operations on the aircraft carrier, and the landing safety is very important to the pilot and the flight deck operation. The problem of landing path selection is studied in this paper as there several candidates corresponding to different situations. A fuzzy path selection strategy is proposed to solve the problem considering the fuzziness of environmental information and human judgment, and the goal is to provide the pilot with more reasonable decision. The strategy is based on Fuzzy Multi-attribute Group Decision Making (FMAGDM), which has been widely used in industry. Firstly, the background of the path selection problem is given. Then the essential elements of the problem are abstracted to build the conceptual model. A group decision-making method is applied to denote the preference of each decision maker for each alternative route, and the optimal landing path under the current environment is determined taking into account the knowledge and the weight of both decision makers. Experimental studies under different setups, i.e., different environments, are carried out. The results demonstrate that the proposed path selection strategy is validated in different environments, and the optimal landing paths corresponding to different environments can be determined.

CMC/PVA composite nanofiber membrane was prepared by electrostatic spinning method, using carboxymethyl cellulose (CMC) and polyvinyl alcohol (PVA) as raw materials and glutaraldehyde as cross-linking agent. The structure, morphology, thermal stability, and filtration performance of CMC/PVA nanofiber membranes were characterized by advanced instrumental analysis methods such as scanning electron microscopy, Fourier transform infrared spectroscopy, thermogravimetric analysis, ultraviolet analysis and energy spectrum analysis. The results show that the average fiber diameter decreases from 381 nm to 183 nm, when the spinning voltage is 23 KV and the jet speed is 2 µL/min. The obtained fiber has the smallest particle size and the most uniform distribution. Infrared spectroscopy analysis confirms that the adsorption behavior of nanofiber membranes on Cu2+ and Cr6+ is chemical adsorption. The retention rates of CMC/PVA nanofiber membranes for Cu2+ and Cr6+ reached 97% and 98%, respectively.

Image stitching is a crucial aspect of image processing. However, factors like perspective and environment often lead to irregular shapes in stitched images. Cropping or completion methods typically result in substantial loss of information. This paper proposes a method for rectifying irregularly images into rectangles using deformable meshes and residual networks. The method utilizes a convolutional neural network to quantify rigid structures of images. Choosing the most suitable mesh structure based on the extraction results, offering options such as triangular, rectangular, and hexagonal. Subsequently, the irregularly image, predefined mesh structure, and predicted mesh structure are input into a wide residual neural network for regression. The loss function comprises local and global, aimed at minimizing the loss of image information within the mesh and global target. This method not only significantly reduces information loss during rectification but also adapting to different images with various rigid structures. Validation on the DIR-D dataset shows this method outperforms state-of-the-art methods in image rectification.

Both lactic acid and short chain fatty acid (SCFA) play important roles in maintenance of intestinal epithelial structure and function. Trilactic glyceride (TLG) obtains both excellences of lactic acid and SCFA. This study was to investigate the effects of trilactic glyceride on growth performance, blood parameters, liver function, intestinal morphology and intestine function of piglets. Twelve weaned piglets (21±2 d) were randomly allocated to two treatment groups: 1) control group, piglets fed the basal diet; 2) TLG group, piglets fed the basal diet supplemented with 0.5 % TLG. On day 21 of the trial, D-xylose (0.1 g/kg·BW) was orally administrated to all piglets and blood samples were collected 1 h thereafter. Then, all the piglets were sacrificed to examine intestinal mucosal morphology and collect fatty tissue, liver and intestinal mucosa for further analysis. The results showed that: compared with the control group, TLG group decreased blood ALB and GGT on day 10 and 20, TLG group decreased blood TP and increased blood TG on day 20 of the trail (p < 0.05); TLG group decreased blood D-xylose and LDL, increased blood HDL (p < 0.05). These data suggested that supplementing trilactic glyceride had beneficial impacts on promoting nutrients’ metabolism, maintaining intestinal integrity, and alleviating oxidative stress and diarrhoea. Further research of molecular mechanisms showed changing expression levels of related proteins and genes, suggesting that these could be involved in the regulation of the impact. The community composition of the gut microbiota was also found to be altered in several operational taxonomic units within the genus, Prevotella (order Bacteroidales), and the order, Clostridiales.

In the process of construction and operation of the pumping station, a large number of axial flow pumps pose a threat to the survival of fish in the natural environment. Through experiments, the survival conditions of many kinds of fish in extreme positive and negative pressure environment are explored, and -40 kPa is established as the low pressure damage threshold, which is used as a reference to analyze the probability of fish damage caused by pumps. The immersion boundary-lattice Boltzmann numerical method (LES-IB-LBM) based on large eddy simulation is used to optimize the parameters of the prototype runner of axial flow pump. A new type of runner with leading edge thickness of 11.4mm and blade cutting angle of 18 ° is optimized. This kind of runner has both hydraulic performance and fish-passing ability. The runner of the fish-friendly axial flow pump effectively guides the fish into the low risk area and reduces the risk of friction, shear and impact damage to the fish. the total impact mortality ratio of the runner of the axial flow pump before and after optimization is close to 7:1. The pressure damage analysis shows that the lowest negative pressure of the fish is -59.2 kPa, which is higher than -64.5 kPa of the prototype pump, and the highest positive pressure of the body surface is 11.8 kPa, which is lower than the 43.8 kPa of the prototype pump. Shear damage analysis shows that the fish will not be damaged by shear in the prototype pump and fish-friendly pump.

Wireless sensor networks are widely used in many applications such as environmental monitoring, health care, smart grid and surveillance. Many security protocols have been proposed and intensively studied due to the inherent nature of wireless networks. In particular, Wu et al. proposed a promising authentication scheme which is sufficiently robust against various attacks. However, according to our analysis, Wu et al.'s scheme has two serious security weaknesses against malicious outsiders. First, their scheme can lead to user impersonation attacks. Second, user anonymity is not preserved in their scheme. In this paper, we present these vulnerabilities of Wu et al.'s scheme in detail. We also propose a new scheme by fixing such vulnerabilities and improving the performance of the protocol.

TiO2-based building materials have air purification, auto-cleaning and sterilization functions, and these innovative green building materials have great potential for energy-saving and emission reduction applications in the future. However, there are still great challenges in improving photocatalytic efficiency and stability from laboratory to practical applications. In recent years, researchers have done a lot of work to improve the efficiency and stability of TiO2-based building materials. This paper briefly discussed the air purification principle by photocatalytic building, and the preparation techniques of TiO2-based building materials and the strategies to improve the efficiency of TiO2. Moreover, this paper has outlined the key factors that affect the photocatalytic building performance in practical applications, and analyzed the limitations and future development trends. Finally, we proposed some suggestions for further research on photocatalytic buildings and its application in practice, aiming to provide an efficient reference for developing highly efficient and stable photocatalytic building materials. The aim of this paper is to provide effective guidance for the application of TiO2-based photo-catalysts in the field of green buildings, helping to develop more efficient and stable low-carbon buildings for the development of sustainable cities.

With the continuous development of deep learning, the application of object detection based on deep neural network in the coal mine has been expanding. Simultaneously, as the production applications demand higher recognition accuracy, most research chooses to enlarge the depth and parameters of the network to improve accuracy. However, due to the limited computing resources in the coal mining face, it is challenging to meet the computation demands of a large number of hardware resources. Therefore, this paper proposes a lightweight object detection algorithm designed specifically for coal mining face, referred to as CM-YOLOv8. The algorithm introduces adaptive predefined anchor boxes tailored to the coal mining face dataset to enhance the detection performance of various targets. Simultaneously, a pruning method based on the L1 norm is designed, significantly compressing the model's computation and parameter volume without compromising accuracy. The proposed algorithm is validated on the coal mining dataset DsLMF+, achieving a compression rate of 40% on the model volume with less than a 1% drop in accuracy. Comparative analysis with other existing algorithms demonstrates its efficiency and practicality in coal mining scenarios. The experiments confirm that CM-YOLOv8 significantly reduces the model's computational requirements and volume while maintaining high accuracy.

Smart Internet of Vehicles (IoVs) combined with Artificial Intelligence (AI) will contribute to vehicle decision-making in the Intelligent Transportation System (ITS). Multi-Vehicle Pursuit games (MVP), a multi-vehicle cooperative ability to capture mobile targets, is becoming a hot research topic gradually. Although there are some achievements in the field of MVP in the open space environment, the urban area brings complicated road structures and restricted moving spaces as challenges to the resolution of MVP games. We define an Observation-constrained MVP (OMVP) problem in this paper and propose a Transformer-based Time and Team Reinforcement Learning scheme (T3OMVP) to address the problem. First, a new multi-vehicle pursuit model is constructed based on decentralized partially observed Markov decision processes (Dec-POMDP) to instantiate this problem. Second, by introducing and modifying the transformer-based observation sequence, QMIX is redefined to adapt to the complicated road structure, restricted moving spaces and constrained observations, so as to control vehicles to pursue the target combining the vehicle’s observations. Third, a multi-intersection urban environment is built to verify the proposed scheme. Extensive experimental results demonstrate that the proposed T3OMVP scheme achieves significant improvements relative to state-of-the-art QMIX approaches by 9.66%~106.25%. Code is available at https://github.com/pipihaiziguai/T3OMVP.

This paper presents an optimized feature-centered reflection symmetry axis detection and localization framework for object perception. The proposed framework is formed to obtain an improved reflection symmetry axis based on the salient symmetry feature. It starts with a refined Multi-scale Saliency Symmetry Model (MSSM), which is realized by applying isotropic symmetry operator on salient points in scale-space rather than all pixels. In each scale, salient points are initially extracted as local extremal from an image, and they are further refined by a multi-scale implementation for generating salient symmetry feature maps. A Symmetric Transformation Matrix is then computed using the optimal feature matching pairs, which can be explicitly used as an abstract representation of the constraint regions of symmetry objects in an image to optimize the performance of the potential symmetry axis detection. The framework has been investigated experimentally both on the classical dataset from a symmetry detection challenge and the latest dataset. It has shown that the framework can get a better or comparative result and also can be further adapted into terminated human--computer equipment for reflection symmetry object perception and tracking.

Shear dynamics simulation under extreme pressure was used to optimise the composition of ester-based lubricant base oil and extreme pressure additives. As a result, the ester-based lubricant in the weak-gel drilling fluid achieves reduction and increases the efficiency in drilling construction, and the field operation efficiency improves. The results of base oil lubrication simulation show that three base oils, namely, methyl oleate, ethyl oleate and butyl oleate, can be stably adsorbed on the surface layer of the shear surface. Methyl oleate has the lowest system temperature after shear stabilisation and has a high load-bearing capacity. The shear stress of methyl oleate decreases by changing the initial shear temperature and speed. It increases by 6.36 MPa when the speed increases from 10 m/s to 30 m/s. At this time, the shear stress of butyl oleate increases by 10.11 MPa. The results of the four-ball friction experiments show that the radius of the abrasion spot of methyl oleate is 179.83 μm, which is smaller than that of the other two base oils. Moreover, the friction coefficient of methyl oleate is 0.0018, which is approximately 1/3 of that of butyl oleate. Methyl oleate has better lubrication efficiency. The shear simulation results are consistent with the experimental results. The simulation can be used for the molecular design of lubricant materials. The oleic acid amide–containing amine group and the glyceride oleic–containing hydroxyl group were selected as the extreme pressure functional components for shear simulation. Results show that the shear stress of oleic acid amide is much lower than that of oleic acid glyceride when the initial shear temperature and speed change. The extreme pressure lubrication component–containing amine group is better than the extreme pressure lubrication material–containing hydroxyl group. The effects of different oleamide contents in the two-component mixtures on the lubricating properties were investigated through shear simulation, with methyl oleate as the base oil and oleamide as the extreme pressure functional component. The simulation results show that the lubricant has the optimal shear stress when 10% oleamide is added to the lubricant. The base properties of the lubricant were tested using a mixture of 90% methyl oleate and 10% oleamide, formulated as a lubricant. Results show that the friction coefficient can be reduced to 0.03 when 0.5% of the lubricant is added to the base mud. Moreover, the lubricant film formed shows high strength. Then, 1% lubricant was added to the weak-gel drilling fluid to evaluate the effect of the lubricant on the gel structure of the drilling fluid. Results show that adding lubricant does not affect the rheological properties of the drilling fluid. The gel structure of the system also remains stable even after 7 days of continuous ageing. The results of the field experiments in Hua3-01 well show that adding 1% ester-based lubricant to the field drilling fluid reduces the drilling friction by 33%. Thus, the efficiency of directional side drilling can be effectively improved, complicated accidents, such as poor starting and stopping of drilling and stuck jamming, can be avoided, and the goals of reducing quantity and increasing efficiency can be completed.

Background: Exposure to inorganic arsenic (iAs) remains a global public health problem. The liver is the main target organ of arsenic, leading to arsenic-induced liver fibrosis. Autophagy is involved. Phosphatase and tensin homology deleted on chromosome ten (PTEN) may participate in arsenic-induced liver fibrosis by regulating autophagy, but the exact mechanisms remain unclear. We established a mouse model of arsenic poisoning through the drinking water, and a fibrosis model using the huma stellate cell (HSC) line LX-2, which was exposed to NaAsO₂ for 24h. HE and Masson staining was adopted to observe the degree of liver fibrosis. The cells were transfected using PTEN overexpression plasmid. Western blot and qRT-PCR were used to determine the levels of protein/mRNA expression. The in vivo results were confirmed in HSCs exposed to NaAsO₂, with changes suggesting fibrosis as seen in mice. NaAsO₂ upregulated the expression of the autophagic markers microtubule-associated protein light chain A/B (LC3), recombinant human autophagy effector protein (Beclin-1), hairy and enhancer of split homolog-1 (HES1), but downregulated PTEN. α-smooth muscle actin (α-SMA) expression was significantly upregulated in all NaAsO₂ groups. PTEN overexpression altered NaAsO₂-induced autophagy which LC3, Beclin-1 were downregulated. Notch1, HES1, α-SMA, and collagenⅠexpression were all downregulated in the NaAsO₂ groups. In conclusion, PTEN overexpression might decrease autophagy and inhibit fibrosis progression caused by this toxin. The NOTCH1/HES1 pathway is likely to be involved in this process. Most previous studies did not investigate PTEN and arsenic-induced liver fibrosis specifically. The present study highlights the importance of targeting PTEN for the management of arsenic exposure.

Health care in Canada is managed by provinces/territories. We investigated regional differences in survival among Canadians diagnosed with central nervous system (CNS) tumours. We identified 50,670 patients diagnosed with a first-ever primary CNS tumour between 2008 and 2017 with follow-up until December 31, 2017. We selected the four highest incidence histologies and used proportional hazards regression to estimate hazard ratios (HRs) for five regions (British Columbia, Prairie provinces, Ontario, Atlantic provinces and the Territories), adjusting for sex, tumour behaviour and patient age. Ontario had the best survival profile for all histologies investigated. The Atlantic provinces had the highest HR for glioblastoma (HR=1.26, 95% CI:1.18-1.35) and malignant glioma not otherwise specified (NOS) (Overall: HR=1.87, 95% CI:1.43-2.43; Pediatric population: HR=2.86, 95% CI:1.28-6.39). For meningioma, the Territories had the highest HR (HR=2.44, 95% CI:1.09-5.45) followed by the Prairie provinces (HR=1.52, 95% CI:1.38-1.67). For malignant unclassified tumours, the highest HRs were in British Columbia (HR=1.45, 95% CI:1.22-1.71) and the Atlantic provinces (HR=1.40, 95% CI:1.13-1.74). There are regional differences in the survival of CNS patients at the population level for all four specific histological types of CNS tumours investigated. Factors contributing to these observed regional survival differences are unknown and warrant further investigation.

The key to simulating soil erosion is to calculate the vegetation cover (C) factor. Methods that apply remote sensing to calculate C factor at regional scale cannot directly use the C factor formula. That is because the C factor formula is obtained by experiment, and needs the coverage ratio data of croplands, woodlands and grasslands at standard plot scale. In this paper, we present a C factor conversion method from a standard plot to a km-sized grid based on large sample theory and multi-scale remote sensing. Results show that: 1) Compared with the existing C factor formula, our method is based on the coverage ratio of croplands, woodlands and grasslands on a km-sized grid, takes the C factor formula obtained from the standard plot experiment and applies it to regional scale. This method improves the applicability of the C factor formula, and can satisfy the need to simulate soil erosion in large areas. 2) The vegetation coverage obtained by remote sensing interpretation is significantly consistent (paired samples t-test, t = −0.03, df = 0.12, 2-tail significance p < 0.05) and significantly correlated with the measured vegetation coverage. 3) The C factor of the study area is smaller in the middle, southern and northern regions, and larger in the eastern and western regions. The main reason for that is the distribution of woodlands, the Hunshandake and Horqin sandy lands and the valleys affected by human activities. 4) The method presented in this paper is more meticulous than the C factor method based on the vegetation index, improves the applicability of the C factor formula, and can be used to simulate soil erosion on large scale and provide strong support for regional soil and water conservation planning.

To address the problems of poor recognition, low detection accuracy, a large number of model parameters and computation, complex network structure, and unfavorable portability to embedded devices in traditional tennis ball detection algorithms, this study proposes a lightweight tennis ball detection algorithm YOLOv5s-Z based on Robomater EP. The main work is as follows: Firstly, constructing lightweight G-Backbone and G-Neck network layers to reduce the number of parameters and computation of the network structure. Secondly, the convolutional coordinate attention is incorporated in G-Backbnone to embed the location information into the channel attention, which makes the network obtain the location information in a larger area through multiple convolutions and enhances the expression ability of the mobile network learning features. In addition, the Concat module in the original feature fusion is modified into a weighted bi-directional feature pyramid W-BiFPN with settable learning weights to improve the feature fusion capability and achieve efficient weighted feature fusion and bi-directional cross-scale connectivity. The EIOU loss is introduced to split the influence factor of aspect ratio and calculate the length and width of the target frame and anchor frame respectively, combined with Focal-EIOU Loss to solve the problem of imbalance between difficult and easy samples. The activation function Meta-ACON is introduced to achieve an adaptive selection of whether to activate the neurons and improve the detection accuracy. Finally, the experimental results show that compared with the original algorithm, the YOLOv5s-Z algorithm reduces the number of parameters and computation by 42$\%$ and 44$\%$, the model size by 39$\%$, and 2$\%$ improvement in average accuracy mean value, which verifies the effectiveness of the improved algorithm and the light weight of the model to meet the deployment requirements of embedded devices, and adapts Robomaster EP for accurate detection and real-time recognition of tennis balls.

Seven pieces of Lacquer Lian from Warring States Period to Yuan Dynasty (475 BC- 1368 AD) were analyzed by means of cross-section observation, Raman spectroscopy (RS) and thermally assisted hydrolysis and methylation pyrolysis coupled with gas chromatography/ mass spectroscopy (Py-GC/MS). The results demonstrated that Lacquer Lian was consisted by three layers, including pigment layer in the surface, undercoat layer in the middle and ground layer, the red mineral pigment was cinnabar, and mixture of Chinese lacquer and drying oil was applied as main organic materials. Although lacquering techniques had undergone minimal changes from Warring States Period to Yuan Dynasty, the species of drying oil had changed based on the fact that boiled tung oil was found in the ground layer of lacquerwares from Song Dynasty and Yuan Dynasty. The present research provided direct evidence for the inheritance and development of Chinese lacquer technology.

Masquelet induced-membrane technique for the treatment of segmental bone defects includes a two-stage surgical procedure, and polymethylmethacrylate (PMMA) plays a major role in the treatment. However, the PMMA spacer must be surgically removed. Here, we investigated the potential of poly (lactic-co-glycolic acid) (PLGA) nanofibers, a biodegradable material to replace PMMA spacer, allowing the bioactive membrane to be induced, and the spacer to degrade without the additional surgery on a rabbit femoral segmental bone defect model. PLGA nanofibers were shown to degrade completely six weeks after implantation in the investigated animals, and a thick membrane was found to circumferentially fold around the segmental bone defects. Results from image studies demonstrated that, in the group without bone graft, all studied femurs exhibited either nonunion or considerable malunion. In contrast, the femurs in the bone graft group had a high union rate without considerable deformities. Histological examinations suggested that the membranous tissue in this group was rich in small blood vessels and the expression of BMP2 and VEGF increased. Our results demonstrate that the biodegradable PLGA nanofibers may be useful for replacing the PMMA spacer as the bioactive-membrane inducer, facilitating the process of healing and removing the need for repeated surgeries.

Extracorporeal membrane oxygenation (ECMO), in conjunction with its life-saving benefits, carries a significant risk of acute brain injury (ABI). Hypoxic-ischemic brain injury (HIBI) is one of the most common types of ABI in ECMO patients. Various risk factors such as history of hypertension, high day 1 lactate level, low pH, cannulation technique, large peri-cannulation PaCO2 drop (∆PaCO2), and early low pulse pressure, have been associated with the development of HIBI in ECMO patients. The pathogenic mechanisms of HIBI in ECMO are complex and multifactorial, attributing to the underlying pathology requiring initiation of ECMO and the risk of HIBI associated with ECMO itself. HIBI is likely to occur in the peri-cannulation or peri-decannulation time secondary to underlying refractory cardiopulmonary failure before or after ECMO. Current therapeutics target pathological mechanisms, cerebral hypoxia and is-chemia, by employing targeted temperature management in the case of extracorporeal cardiopulmonary resuscitation (eCPR), and optimizing cerebral O2 saturations and cerebral perfusion. This review describes the pathophysiology, neuromonitoring, and therapeutic techniques to improve neurological outcomes in ECMO patients so as to prevent and minimize the morbidity of HIBI. Further studies aimed at stand-ardizing the most relevant neuromonitoring techniques, optimizing cerebral perfusion, and minimizing the severity of HIBI once it occurs will improve long-term neurological outcomes in ECMO patients.

The surface velocity of the Amery Ice Shelf (AIS) is vital to assessing its stability and mass balance. Previous studies have shown that the AIS basin has a stable multi-year average surface velocity. However, spatiotemporal variations in the surface velocity of the AIS and the underlying physical mechanism remain poorly understood. This study combined offset tracking and DInSAR methods to extract the monthly average surface velocity of the AIS and obtained the inter-annual surface velocity from the ITS_LIVE product. An uneven spatial distribution in inter-annual variation of the surface velocity was observed between 2000–2022, although the magnitude of variation was small at less than 20.5 m/yr. The increase and decrease in surface velocity on the eastern and western-central sides of the AIS, respectively, could be attributed to the change in the thickness of the AIS. There was clear seasonal variation in monthly average surface velocity at the eastern side of the AIS between 2017–2021, which could be attributed to variations in the area and thickness of fast-ice and also to variations in ocean temperature. This study suggested that changes in fast-ice and ocean temperature are the main factors driving spatiotemporal variation in the surface velocity of the AIS.

T-2 toxin produced by fungi of Fusarium genus is highly toxic to human and animals and has been shown to induce apoptosis in various organs/tissues. Apoptosis and autophagy are interconnected processes and these interactions are important for cellular homeostasis as well as pathogenesis. In this study, we report for the first time that T-2 toxin induced autophagy in human liver cells (L02). We showed that T-2 toxin induced the formation of acidic vesicular organelles, concordant with the time and dose-dependent alterations in LC3-phosphatidylethanolamine conjugate (LC3-II) LC3-I/II and p62/SQSTM1 suggesting an enhanced autophagic flux. The T-2 toxin-induced formation of autophagosome and lysosomal fusion was observed by expressing mRFP-GFP-LC3 in L02 cells by lentiviral transduction, and autophagosome was observed by transmission electron microcopy. We found that while T-2 toxin activated both apoptosis and autophagy, activation of autophagy appears to be a leading event reflecting the protective mechanism of cells against the insults by T-2 toxin. Activating autophagy by rapamycin (RAPA) inhibited the apoptosis while suppressing autophagy by chloroquine greatly enhanced the T-2 toxin-induced apoptosis suggesting the crosstalk of autophagy and apoptosis. In summary, our study showed that activation of autophagy protects liver cells from T-2 toxin-induced apoptosis suggesting autophagy may be targeted for prevention of the T-2 toxin-induced toxicity in human and animals.

High-precision ground point cloud data has a wide range of applications in various fields, and the separation of ground points from non-ground points is a crucial preprocessing step. Therefore, designing an efficient, accurate, and stable ground extraction algorithm is of great significance for improving the processing efficiency and analysis accuracy of point cloud data. The study area in this article was a Park in Guilin, Guangxi, China. The point cloud was obtained by utilizing the UAV platform. In order to improve the stability and accuracy of the Filter algorithm, this article proposed a triangular grid filter based on Slope Filter, found violation points by the spatial position relationship within each point in the triangulation network, improved KD-Tree-Based Euclidean Clustering, and applied it to the non-ground points extraction, this method has good accuracy, stability and achieves good results in separating ground points from non-ground points. At first, using Slope Filter to remove some non-ground points, to reduce the error of taking ground points as non-ground points; Secondly, established a triangular grid based on the triangular relationship between each point, the violation-triangle can determin through the grid, and then the corresponding violation points were found in the violation-triangle; Thirdly, according to the three-point collinear method to extract the regular points, used these points to extract the regular landmarks by KD-Tree-Based Euclidean Clustering and Convex Hull Algorithm; Finally, removed disperse points and irregular landmarks by Clustering Algorithm. In order to confirm the superiority of this algorithm, this article compared the filter effects of various algorithms on the study area and filtered the 15 sample data provided by ISPRS, and obtained an average error of 3. 46%. The results showed that the algorithm in this article have a high processing efficiency and accuracy, which can greatly improve the processing efficiency of point cloud data in practical applications.

Lower urinary tract dysfunction (LUTD) was associated with bladder inflammation and tissue hypoxia with oxidative stress. This study investigated the profiles of urine inflammatory and oxidative stress biomarkers in females with LUTD and to develop a urine biomarker-based decision tree model for the prediction. Urine samples were collected from 31 female patients with detrusor overactivity (DO), 45 with dysfunctional voiding (DV), and 114 with interstitial cystitis/ bladder pain syndrome (IC/BPS). The targeted analytes included 15 inflammatory cytokines and 3 oxidative stress biomarkers (8-hydroxy-2-deoxyguanosin, 8-isoprostane, and total antioxidant capacity [TAC]). Different female LUTD groups had distinct urine biomarker profiles, including IL-1β, IL-2, IL-8, IL-10, eotaxin, CXCL10, MIP-1β, RANTES, TNFα, VEGF, NGF, BDNF, 8-isoprostane, and TAC. The urine biomarker-based decision tree, using IL-8, IL-10, CXCL10, TNFα, NGF, and BDNF as nodes, demonstrated an overall accuracy rate of 85.3%. DO, DV, and IC/BPS accuracy rates were 74.2%, 73.3%, and 93.0%, respectively. Internal validation revealed similar overall accuracy rate. Random forest models supported the significance and importance of all selected nodes in this decision tree model. Urine inflammatory and oxidative stress biomarker profiles of different female LUTDs were different. This internally validated urine biomarker-based decision tree model predicted different female LUTDs with high accuracy.

This paper proposes two max-pooling engines, named the RTB-MAXP engine and the CMB-MAXP engine, with a scalable window size parameter for FPGA-based convolutional neural network (CNN) implementation. The max-pooling operation for the CNN can be decomposed into two stages, i.e., a horizontal axis max-pooling operation and a vertical axis max-pooling operation. These two one-dimensional max-pooling operations are performed by tracking the rank of the values within the window in the RTB-MAXP engine and cascading the maximum operations of the values in CMB-MAXP engine. Both the RBM-MAXP engine and the CMB-MAXP engine were implemented using VHSIC Hardware Description Language (VHDL) and verified by simulations. They have been employed for and tested in our CNN accelerator targeting at the CNN model YOLOv4-CSP-S-Leaky for object detection.

This paper investigates a distributed, coordinated motion control network based on multiple direct-drive, linear switched reluctance machines (LSRMs). A hierarchical, two-level synchronization control strategy is proposed for the four LSRMs based motion control network. The high-level, reference signals agreement algorithm is first employed to correct the asynchronous behaviors of the position commands. Then, the low-level tracking synchronization method is applied for the collaborative position control of the four LSRMs. The proposed two-level, fault-tolerant control strategy eliminates the asynchrony of the reference signals and it also guarantees the coordinated tracking control performance of the four LSRMs. Experimental results demonstrate that effective coordinated tracking control can be ensured, based on successful agreement of reference signals and an absolute tracking error falling within 2 mm can be achieved.

A La2FeCrO6 (LFCO) double perovskite powders were synthesized by hydrothermal method, which crystallized in an orthorhombic (Pnma) structure and exhibited a spherical morphology with average particle size of 900 nm. Fourier transformation infrared spectroscopy confirmed the octahedral coordination of Fe and Cr ions in the powders. XPS spectra revealed dual oxide states of Fe (Fe2+/Fe3+) and Cr (Cr3+/Cr4+) elements, and oxygen element appeared as lattice oxygen and defect oxygen, respectively. The LFCO powders exhibit ferromagnetic behavior at 5 K with saturation magnetization of 0.31 μB/f.u., coercive field of 8.0 kOe, and Curie temperature of 200 K. Griffiths phase appeared in the powders between 200 K and 223 K. The LFCO ceramics displayed a butterfly-like magnetoresistance (MR)-magnetic field (H) curve at 5 K with MR (5 K, 6 T) value of -4.07%. Temperature dependence of resistivity of the LFCO ceramics demonstrated their semiconducting nature. Electrical transport data were fitted by different conduction models. Strong frequency dispersion dielectric behavior was observed in the LFCO ceramics. A dielectric abnormality observed around 260 K, was ascribed to the jumping of electrons trapped in shallow levels created by oxygen vacancies. The dielectric relaxation behavior exhibited by dielectric loss between 160 K and 260 K, was contributed to the singly-ionized oxygen vacancies.

As one of the most promising ablative fillers, multi-walled carbon nanotubes (MWCNTs) have been used to improve the ablative resistance of Ethylene-Propylene-Diene Monomer (EPDM) insulators by facilitating the carbothermal reduction reaction of silica. However, the contribution of MWCNTs to char layer structure of the insulators was unclear. In this work, the effects of MWCNTs on char layer structure and ablative resistance were investigated in different EPDM-based insulators with and without silica. The results showed that adding only 3 phr MWCNTs can reduce the linear ablation rate of EPDM-based insulators without silica by 31.7%, while 6 phr MWCNTs are required to obtain similar results in EPDM-based insulators with silica. Both the char layer morphology of the two insulators gradually evolved into dense porous structure as MWCNTs content increasing, but their formation mechanisms are different. The XRD and Raman spectrum showed that different physicochemical reactions occurred around MWCNTs under different charring components. The proposed ablation mechanism was further verified by designing alternating multilayer distribution of MWCNTs and silica. This work can guide the construction of desirable char layer structure for increasing ablative resistance of EPDM-based insulators.

We report an all-optical radio-frequency (RF) spectrum analyzer with a bandwidth greater than 5 terahertz (THz), based on a 50-cm long spiral waveguide in a CMOS-compatible high-index doped silica platform. By carefully mapping out the dispersion profile of the waveguides for different thicknesses, we identify the optimal design to achieve near zero dispersion in the C-band. To demonstrate the capability of the RF spectrum analyzer, we measure the optical output of a femtosecond fiber laser with an ultrafast optical RF spectrum in the terahertz regime.

Plant Factory Transplanter (PFT) is a key component of the plant factory system. Its operation status directly affects the quality and survival rate of planted seedlings, which in turn affects the overall yield and economic efficiency. To monitor the operation status and transplanting quality of a transplanting machine in a timely manner, the primary task is to use a computerized and easy-to-use method to monitor the transplanting units. Inspired by the latest developments in augmented reality and robotics, a DT model-based and data-driven online monitoring method for plant factory transplanting equipment is proposed. First, a data-driven and virtual model approach is combined to construct a multi-domain digital twin of the transplanting equipment. Then, taking the vibration frequency domain signal above the transplanting manipulator and the image features of the transplanting seedling tray as input variables, the evaluation method and configuration method of the PFT digital twin system are proposed. Finally, the effect of the transplanter is evaluated, and the cycle can be repeated to optimize the transplanter to achieve optimal operation parameters. The results show that the digital twin model can effectively use the sensor data to identify the mechanical vibration characteristics and avoid affecting transplanting quality due to mechanical resonance. At a transplanting rate of 3000 plants/h, the transplanting efficiency can be maintained at a high level and the vibration signal of X, Y, Z-axis above the transplanting manipulator is relatively calm. In this case, Combined the optimal threshold method with the traditional Wiener algorithm, the identification rate of healthy potted seedlings can reach 94.3%. Through comprehensively using the optimal threshold method and 3D block matching filtering algorithm for image threshold segmentation and denoising, the recognition rate of healthy seedlings has reached over 96.10%. In addition, the developed digital twin can predict the operational efficiency and optimal timing of the detected transplanter, even if the environmental and sensor data are not included in the training. The proposed digital twin model can be used for damage detection and operational effectiveness assessment of other plant factory equipment structures.

.Purpose: This paper presents a comparative analysis of state-of-the-art DIR algorithms in the context of head and neck squamous cell carcinoma (HNSCC) radiation therapy. Materials and Methods: We used a dataset of head and neck cancer patients within the Cancer Image Archive, which includes 31 patients with 3D CT image data from pre-treatment, mid-treatment, and post-treatment stages of radiotherapy. We applied DIR algorithms to two datasets, one for pre-treatment to mid-treatment registration and another for mid-treatment to post-treatment registration, by aligning one CT image to another CT image. To quantitatively analyze the patient data, we focused on the spinal cord, optic nerve, brain stem, cochlea, and PTV as the OAR datasets. To verify the DIR algorithm, we used two non-learning-based methods, SyN and NiftyReg, as well as three deep learning-based methods, Voxelmorph, Cyclemorph, and Transmorph. We trained a deep learning model by adjusting the ratio of the training dataset, validation dataset, and test dataset to 7:1:2. Results: The average DSCs of SyN and NiftyReg, the non-learning-based methods, were 0.74±0.06 and 0.70±0.12, respectively. The deep learning-based methods, Voxelmorph, Cyclemorph, and Transmorph, had average DSCs of 0.72±0.08, 0.68±0.11, and 0.69±0.13, respectively. The deep learning DIR algorithm produced transformed outputs of OAR/PTV in a shorter time than other models, including commercial and conventional mathematical algorithms (At Inference(sec/images), Voxelmorph: 0.36, Cyclemorph: 0.3, Transmorph: 5.1, SyN: 140, NiftyReg: 40.2). Conclusions: In conclusion, our study provides a comprehensive comparison of commercial DIR algorithms with traditional and deep learning-based DIR methods. Our results demonstrate that commercial DIR algorithms outperform traditional DIR methods in terms of accuracy and efficiency. However, we also show that deep learning-based DIR methods have the potential to achieve similar performance to commercial algorithms with proper training and optimization. Our findings suggest that both commercial and deep learning-based DIR methods have their respective advantages and limitations, and the choice of method should depend on the specific requirements of the clinical application. Overall, our study contributes to ongoing efforts to improve the accuracy and efficiency of DIR methods for better patient outcomes.

Cooking is a very decentralized and private way of energy consumption in human activities. The existing investigation and statistical analysis can’t effectively calculate the proportion of population relying on clean cooking fuel and utilization technology in the region. Therefore, based on the big data of the earth, this paper adopts the combination of spatial analysis and statistical analysis to determine the survey sample area, and according to the economic conditions, topographic characteristics, national policies for new energy construction and living habits of the provinces and cities under investigation, the questionnaire survey is conducted for the research area to calculate the proportion of the regional population relying on clean cooking fuels and utilization technologies. Taking the south of the Yangtze River in China as an example, the paper effectively calculates that 88.25% of the population depends on clean cooking fuel and technology in this region, of which 89.81% are in urban areas and 79.87% are in rural areas. Analysis of the survey data shows that the proportion of the population using clean cooking fuels and technologies is related to factors such as economic development, income and resource endowment. There is a large urban–rural gap in terms of energy consumption tendency and structure in the south of the Yangtze River in China and cooking energy consumption in rural households also varies from region to region. The technical ideas and conclusions of the paper have high reference application value, which can help promote the upgrading of clean energy utilization and provide data basis for relevant decision and policy making.

The Oriental ratsnake Ptyas mucosa is a common non-venomous snake of the colubrid family, with a wide geographic range spanning much of South and Southeast Asia. P. mucosa is widely cultivated dut to it used in traditional medicine, scientific research, and handicrafts. Therefore, genome resources could play an important role in the efficacy of traditional medicine and the analysis of the living environment of the species. We collected a snake sample in Hezhou, Guangxi, China, which was identified as P. mucosa by morphological identification. Here we present a highly continuous P. mucosa genome with a genome size of 1.74Gb. The scaffold N50 length is 9.57Mb and the maximal length of scaffold is 78.3Mb, the P. mucosa genome has a CG content of 37.9% and the integrity of the gene reached 86.6%.Assembled using long-reads, the total length of the repeat sequence in the genome reached 735 Mb, and its repeat content was as high as 42.19%. A total of 24,869 functional genes were annotated. This study will assist in the understanding of the P. mucosa, and also provide a basis for medicinal research.

Genome-scale metabolic model (GEM) is a powerful tool for interpreting and predicting cellular phenotypes under various environmental and genetic perturbations. However, GEM only consid-ers stoichiometric constraints, and the simulated growth and product yield values will show a monotonic linear increase with increasing substrate uptake rate, which deviates from the experi-mentally measured values. Recently, the integration of enzymatic constraints into stoichiometry-based GEMs was proven to be effective in making novel discoveries and predicting new engineer-ing targets. Here we present the first genome-scale enzyme-constrained model (eciCW773) for Corynebacterium glutamicum reconstructed by integrating enzyme kinetic data from various sources using ECMpy workflow based on the high-quality GEM of C. glutamicum (obtained by modifying the iCW773 model). The enzyme-constrained model improved the prediction of pheno-types and simulated overflow metabolism, while also recapitulating the trade-off between biomass yield and enzyme usage efficiency. Finally, we used eciCW773 to identify several gene modifica-tion targets for L-lysine production, most of which agree with previously reported genes. This study shows that incorporating enzyme kinetic information into the GEM enhances the cellular phenotypes prediction of C. glutamicum, which can help identify key enzymes and thus provide reliable guidance for metabolic engineering.

Abstract: The traditional model of closed circuit ball milling systems has been used for several decades, however, if the classifier of the closed circuit ball mill system performs the duties of both pre-classification and check-classification, the characterization error of the traditional model is large. To address this problem, a new model is obtained by modifying and supplementing the traditional one. The most important feature of the new model compared to the traditional model is that the circulating load is considered to be the fresh feed for the entire system rather than the ball mill. The error between the slurry level height calculated using the traditional model and the actual is 52.31%, which is 13.77 times higher than that of the new model. When the relative capacity varies greatly, that of the ball mill calculated by the traditional model fluctuates between 0.95 and 1.15, while the new model is 0.6 to 1.4. The new model has a higher accuracy than the traditional model in characterizing the production status of the grinding system, which is of some significance for industrial production.

A convenient and efficient strategy for the preparation of 2-sulfonylindoles has been achieved through iodophor/H2O2-mediated 2-sulfonylation of indoles with readily available sulfonyl hydrazides in aqueous phase. Iodophor is commercially available and serves as the green catalyst and aqueous phase. A series of 2-sulfonylated products from indoles and N-methylpyrrole were synthesized in moderate yields in only 10 min. Control experiments were also conducted to reveal the mechanism. This method is environment friendly, easy to operate and suitable for a wide range of substrates.

Grafting is an effective way to increase plant tolerance to biotic and abiotic stressors, it is widely used in watermelon production. However, grafting is labor intensive due to the additional time is required, such as the management of rootstock regrowth. This study used a new grafting tool to destroy (remove) the epidermis of pumpkin and bottle gourd rootstock cotyledon base during grafting, we called this a new grafting method. Compared with the traditional grafting (100%), the new grafting method had significantly lower rate of rootstock regrowth (2-23%), higher watermelon scion dry weight and leaf area. In addition, the time used for the new hole insertion and one cotyledon grafting method to destroy (remove) the epidermis of rootstock cotyledon base (4.2 s/plant, 4.2 s/plant) is significantly shorter than the time required to remove the rootstock regrowth manually in the traditional grafting (9.3 s/plant, 8.8 s/plant). Thus, this study developed a new grafting method for watermelon to inhibit rootstock regrowth and enhance scion growth, and this new method is cost-effective for grafted watermelon seedlings.

Lirianthe delavayi has valuable ornamental and medicinal value, is an important economic tree, and has a long history of cultivation. As important regulatory molecules, miRNAs are involved in important physiological processes, such as the plant stress response, organ morphogenesis, hormone secretion, and signaling. In this study, based on miRNA sequencing analysis of wild and cultivated Lirianthe delavayi, we explored the differences in posttranscriptional regulation during the cultivation of Lirianthe delavayi from the aspect of miRNA molecular regulation. The results revealed the following: 1. A total of 365 miRNAs were sequenced and identified, and their first bases had obvious uracil (U) base preferences. Among them, 242 miRNAs were classified into 32 miRNA families; 2. Analysis of miRNA expression differences revealed that 39 miRNAs had significant expression differences between wild and cultivated populations; 3. Bioinformatics target gene prediction and target gene enrichment analysis of significantly differentially expressed miRNAs revealed that the target genes were significantly enriched in plant‒pathogen interactions, sphingolipid metabolism, defense responses, and ADP binding. 4. The plant‒pathogen interaction pathway involves seven differentially expressed miRNAs and 30 miRNA‒target gene regulatory pairs, which are involved mainly in pathogen signature molecule recognition and binding, signal transduction, and the regulation of disease resistance molecules or gene expression; Ath-MIR169g-p3_2ss7AG19GA, ath-MIR169g-p5_2ss7AG19GA, and ath-miR408-3p_L-3 are expressed only in wild population, and it is hypothesized that the domestication process from wild to cultivation species may be accompanied by the loss of disease resistance-related miRNAs. This study provides a reference for exploring the posttranscriptional-level regulatory mechanisms of adaptive changes in Lirianthe delavayi from wild to cultivated.

Studies on the neurobiological causes of anxiety disorders suggest that the GABA system in-creases synaptic concentration and enhances the affinity of GABAA (type A) receptors for ben-zo-diazepine ligands. Flumazenil antagonizes the benzodiazepine binding site of the GABA (γ-aminobutyric acid) type /benzodiazepine receptor (BZR) complex in the central nervous sys-tem (CNS). The integration of the metabolites of flumazenil by LC-tandem mass spectrometry will complete understanding of the in vivo metabolism of flumazenil and accelerate radio-pharmaceutical inspection and registration. The main goal of our study was to investigate using reversed-phase HPLC (PR-HPLC) coupled with electrospray ionization triple quadrupole tan-dem mass spectrometry (ESI-QqQ MS) for the identification of flumazenil and its metabolites in a hepatic matrix. And a carrier-free nucleophilic fluorination with automatic synthesizer for [18F]flumazenil which applied to in vivo nano-positron emission tomography (Nano-PET)/computed tomography (CT) imaging and ex vivo bio-distribution used to analyze in normal rats. The study showed that 50% of the flumazenil was bio-transformed at 60 min by the rat liver homogenate, while one metabolite (M1) was a methyl transesterification product of flumazenil. In a rat liver microsomes system, two metabolites were identified (M2 and M3) as its carboxylic acid and hydroxylated ethylester forms, respectively. [18F]flumazenil in vivo nanoPET/CT imag-ing and ex vivo bio-distribution assay also showed significant effects on GABAA receptor availa-bility in the amygdala, prefrontal cortex, cortex, and hippocampus in the rat brain, worriless about the formation of metabolites. We showed completion of the bio-transformed course of flumazenil by the hepatic system; and [18F]flumazenil can be a good ligand and serve as a PET agent for determination of GABAA/BZR complex for multiplex neurological syndromes in the clinical stage.

This study aimed to enhance the compatibility of glass ionomer cement (GIC) with tooth tissue by chemically modifying its primary component, calciumfluoroaluminosilicate (CFAS), through the incorporation of nanorod hydroxyapatite (nHA). The process involved binding L-glutamic acid to nHA, followed by activation and binding of albumin to create nHA immobilized with albumin. This modified nHA was then used to surface-modify CFAS particles, producing nHA-CFAS powder. The modified powder was mixed with poly(acrylic acid) and UV-cured to form GIC containing nHA-CFAS (GIC-nHA). Fourier transform infrared spectroscopy and scanning electron microscopy (SEM) confirmed the successful modification. Cytocompatibility tests with osteoblasts showed that GIC-nHA had superior cell viability and bone formation capabilities compared to the control GIC. The improved histocompatibility is attributed to nHA enhancing the biological activity of osteoblasts, indicating that the surface modification method significantly improves the functional integration of GIC with tooth tissue.

Reverse water gas shift reaction (RWGS) is an important process which plays a vital role in many CO2 utilization related reactions. Noble metals are the most active catalysts in RWGS, but the high price and low reserve strangled their applications. In the present work, we reported a non-transition-metal MgAl2O4 catalyst which showed outstanding activity and stability at high temperatures in the RWGS reaction and improved performance after doping of single atomic Nin+. The catalyst can obtain 46% of CO2 conversion in durability test of 75 h at 800 °C under high weight hourly space velocities (225 000 ml g-1 h-1). The adsorption sites, possible reaction route, and effects of Nin+ single atoms on the (111) surface of MgAl2O4 for RWGS were investigated by in situ DRIFTS and DFT calculations. The results indicated that the rate determining reaction step of RWGS on MgAl2O4 and Ni (SA)/MgAl2O4 were both the reaction of OH* + H* → H2O* + *, but the energy barrier was significantly reduced after introducing single atomic Nin+. Nin+ atoms can increase the hydroxyl coverage on the surface of catalyst and Al3+ sites near the Nin+ ion are considered as the predominant active sites for RWGS reactions.

To investigate the differences in cadium (Cd) uptake and translocation among edible rapes and select suitable rape varieties for safe production, a field experiment was carried out with 25 varieties of edible rapes on a farmland polluted with Cd in the central souothern part of Hunan Province. The growing characteristics and Cd contents in rape tissues were measured, and the amount of Cd removed was calculated. The results showed that the growth of 25 rape varieties was not inhibited without withering or inconsistent changes in leaf and so on. The Cd contents in stem-leaf and root of rapes were in the range 0.05-0.26mg·kg-1 and 0.04-0.26mg·kg-1, respectively. Basing on BCF, the stem-leaf showed a greater capacity for Cd transport than root. And the total Cd removed by rape were 0.002-0.016 mg·plant-1. Except for plant height, BCF of soil available Cd from soil to stem-leaf, TCF of Cd from root to stem-leaf and Cd taken away by rape, there was no significant difference among edible rape varieties. Although Cd contents in stem-leaf of 25 rape varieties does not exceed the national safety standards, planting “Lvjin 1”, “Guanyou Qingjing” and “Guanyou brassica” not only reduced soil pollution but also allowed the production of safe leafy rape.

Silicon is an essential trace nutrient for plant growth and is frequently employed to remediate soils contaminated with heavy metals in agriculture. However, silicon’s role and mechanism in reducing heavy metal toxicity have not been well understood, especially for multi-heavy metals. In this study, the effects of silicon-rich materials (silicate, rice husk biochar (RHB), and bentonite) on growth trait, antioxidant response, and heavy metal accumulation and distribution of wheat grown in two soils polluted by multiple heavy metals (Cd, Zn, Pb, and As) were investigated. The results revealed that the addition of silicon-rich materials enhanced plant growth, improved the photosynthetic attributes in leaf tissues, and decreased the contents of Cd, Zn, Pb, and As in wheat shoots and grains. The examination of the subcellular distribution of heavy metals in plants implied that silicon-rich materials transferred heavy metals as intracellular soluble fractions to the cell walls, indicating the reduction of mobility and toxicity of heavy metals in the plants. In addition, the application of the silicon-rich materials reduced oxidative damage in plants by downregulating plant antioxidant response systems and decreasing the production of malondialdehyde (MDA), ascorbic acid (AsA), and glutathione (GSH). Moreover, fractionation analysis of soil heavy metals showed that silicon-rich amendments could convert bioavailable heavy metals into immobilized forms. The results indicated that silicon-rich materials could remediate multi-heavy metal-polluted soils and promote wheat production.

The emergence of diverse infections worldwide, which is a serious global threat to human existence, necessitate the urgent development of novel therapeutic candidates that can combat these diseases with efficacy. Isatin, a secondary metabolite from tryptophan is considered a privileged scaffold and favorable pharmacophore with a unique structural moiety and varied chemical and biological properties resulting in its widespread applications by medicinal chemists. Molecular hybridization is one of the most common and important techniques use in the synthesis of their bioactive hybrids in drug discovery. This review containing published articles from 2005 to 2022 focuses on isatin hybrids which have been synthesized and reported in the literature alongside a discussion on their biological properties. The purpose of this review is to set up the direction for the design and development of isatin-hybrids with tailored biological properties as effective therapeutic candidates inspired by nature.

Pool boiling is extensively utilized in various fields, such as electronics cooling, battery cooling, nuclear power plants, and chemical processing. In the process of temperature control through boiling, the generation and transportation of bubbles play a crucial role in calculating the heat transfer capacity of the system. Therefore, it holds immense significance to gain a profound understanding of the mechanisms underlying bubble formation, growth, and detachment. Currently, numerous mechanistic explanations and empirical correlations have been proposed to elucidate various parameters of bubbles during the boiling process. These findings were considered valuable references in selecting appropriate boiling media and designing efficient heating surfaces. To comprehensively present the progress of bubble formation and heat transfer during the boiling process, the forces exerted on the bubbles was highlighted in this article. And a meticulous review on bubble force analysis and correlation formulas pertaining to various relevant parameters (e.g. nucleation sites density, bubble growth rate, detachment diameter, detachment frequency) were conducted. This review article also were expected to provide a novel foundation for further exploration of enhanced boiling heat transfer.

Our image recognition system mainly judges whether the left upper limb in the image is the left upper limb or the right upper limb through our deep learning model in the image. The doctor then could give the correct surgical position. From the experimental results, it could be found that the precision rate and recall rate of the intelligent image recognition system proposed in this paper for preventing the upper limb dislocation surgery could reach 98% and 93%, respectively. It proved that our artificial intelligent image recognition system, AIIRS, could indeed assist orthopedic surgeons to prevent the occurrence of left and right dislocation in upper limb surgery. At the same time, this paper also completes the IRB application approval through the prototype experimental results and will conduct the second phase of human trials in the future. It showed that the research results of this paper will be of great benefit and research value to upper limb orthopedic surgery.

Our image recognition system mainly judges whether the left upper limb in the image is the left upper limb or the right upper limb through our deep learning model in the image. The doctor then could give the correct surgical position. From the experimental results, it could be found that the precision rate and recall rate of the intelligent image recognition system proposed in this paper for preventing the upper limb dislocation surgery could reach 98% and 93%, respectively. It proved that our intelligent image recognition system could indeed assist orthopedic surgeons to prevent the occurrence of left and right dislocation in upper limb surgery. At the same time, this paper also completes the IRB application approval through the prototype experimental results and will conduct the second phase of human trials in the future. It showed that the research results of this paper will be of great benefit and research value to upper limb orthopedic surgery.

In this paper, MnO2 nanowire (MnO2-NW) modified carbon paper (CP) electrode was developed as a novel electrochemical sensor for sensitive determination of tetrabromobisphenol A (TBBPA). MnO2 nanowire was prepared by a hydrothermal synthesis method, and the morphology and structure of MnO2 were characterized using scanning electron microscopy, X-ray diffraction and X-ray photoelectron spectroscopy. Electrochemical performance of TBBPA on MnO2-NW/CP was investigated by cyclic voltammetry, and the result confirmed that MnO2-NW/CP exhibited excellent sensitive for the determination of TBBPA due to the high specific surface area and good electrical conductivity of the nanowire-like MnO2. Moreover, the important electrochemical factors such as pH value, incubation time and modified material proportion were systematically studied to improve the determination sensitivity. The interferences from similar structure compounds on TBBPA have also been investigated. Under the optimal conditions, MnO2-NW/CP displayed the linear range of 70 500 nM for TBBPA with the detection limit of 3.1 nM, which was superior to some electrochemical methods in references. The work presents a novel and simple method for the determination of TBBPA.

One new cassane diterpene possessing an unusual N bridge between C-19 and C-20 named caesalsappanin R (1), as well as another new diterpene caesalsappanin S (2), were isolated from the seeds of Caesalpinia sappan with methanol extract. Their structures were determined by spectroscopic analysis and examined alongside existing data from prior studies. Their biological activities were profiled by their antiplasmodial activity.

Establishment of diagnostic methods with low detection limits plays a critical role in the maintenance of early diagnosis, prevention of serious neurological complications, and control of the spread of ZIKA. In this study, we established the micro-droplet digital polymerase chain reaction (ddPCR) and real-time fluorescent quantification PCR (qPCR) protocols for the detection of Zika virus based on the NS5 gene. For the Zika standard plasmid, the standard curve of R² was 0.999, and the amplification efficiency was 92.203%, as determined by qPCR. Both ddPCR and qPCR were positive for cell culture of Zika nucleic acid.The minimum detection limit of ddPCR is 1–2 times lower than qPCR. Moreover, all tests of Dengue virus (1–4 serotypes) were negative in cell culture. Overall, these results suggested than ddPCR may have a lower limit of detection than qPCR.

Sustainable development advocates for an environmentally friendly and resource-saving approach, fostering a new quality of productivity that is green and sustainable, and achieving a sustainable development where the economy and the environment are in harmony. The paper is based on clarifying the effects of coordinated development between the economy and the environment, and by establishing an indicator system, applying a remote sensing ecological index, entropy weight method, gray relational degree model, and a coupling coordination model, the relationship of coordinated development of Ordos in 2016-2022 is analyzed from a spatial-temporal perspective. The results are as follows: ① The years of coordinated development between the ecological environment and the economy are in the majority, while the uncoordinated years are fewer. ② The level of coordinated development between the ecological environment and the economy in the various regions of Ordos has been increasing year by year, but it still remains at the barely coordinated and primary coordinated levels. ③ The types of coordinated development between the ecological environment and the economy in Ordos exhibit significant spatial differentiation in terms of spatial distribution and clustering.Therefore, it is necessary to formulate coordinated development policies and measures according to the constraining factors of different regions.

Ehretia laevis Roxb. (Boraginaceae) has been extensively used as a traditional remedy for the treatment of a diverse range of ailments related to the respiratory system, the gastrointestinal tract, the reproductive system, and against several infections. This review critically assesses and documents, for the first time, the fragmented information on E. laevis, including its botanical description, folklore uses, bioactive phytometabolites and pharmacological activities. The goal is to explore this plant therapeutically. Ethnomedicinal surveys reveal that E. laevis has been used by tribal communities in Asian countries for the treatment of various disorders. Quantitative and qualitative phytochemical investigations of E. laevis showed the presence of important phytoconstituents such as pentacyclic triterpenoids, phenolic acids, flavonoids, fatty acids, steroids, alkaloids, aliphatic alcohols, hydrocarbons, amino acids, carbohydrates, vitamins and minerals. Fresh plant parts, crude extracts, fractions and isolated compounds have been reported to exhibit broad spectrum of therapeutic activities viz., antioxidant, antiarthritic, antidiabetic, anti-inflammatory, antiulcer, antidiarrheal, antidysenteric, wound healing and anti-infective activities. E. laevis is shown to be an excellent potential source of drugs for the mitigation of jaundice, asthma, dysentery, ulcers, diarrhea, ringworm, eczema, diabetes, fissure, syphilis, cuts and wounds, inflammation, liver problems, venereal and infectious disorders. Although few investigations authenticated its traditional uses but employed uncharacterized crude extracts of the plant, the major concerns raised are reproducibility of therapeutic efficacy and safety of plant material. The outcomes of limited pharmacological screening and reported bioactive compounds of E. laevis suggest that there is an urgent need for in-depth pharmacological investigations of the plant.

Reactions of Co(OAc)24H2O, N‚N'-bis(3-pyridylmethyl)oxalamide (L) and 4,4’-sulfonyldibenzoic acid (H2SDA) afforded four coordination polymers with the same mixed ligands, {[Co(L)(SDA)(H2O)2]·H2O·CH3OH}n, 1, {[Co(L)0.5(SDA)]·2H2O·0.5L}n, 2, {[Co(L)1.5(SDA)(H2O)]·H2O}n, 3, and {[Co2(L)1.5(SDA)2(H2O)2]·4H2O}n, 4, which have been structurally characterized by using single crystal X-ray crystallography. Complexes 1 – 4 are 2D layers, revealing the topologies of sql, 2,6L1, (4,4)Ia and 6L12, respectively, and demonstrating that the metal to ligand ratio, solvent system and reaction temperature are important in determining the structural diversity. Immersion of these complexes into various solvents show that the structural types govern the chemical stabilities of 1 – 4. Reversible structural transformation can be shown for complexes 1 and 2 upon solvent removal and adsorption, while those of 3 and 4 are irreversible.

As climate changes, our daily life has been much influenced by abnormal meteorological phenomena such as heavy rainfall, heat wave, heavy snowfall, and fine dust. Atmospheric air quality is worsening day by day and indoor air quality is also affected by interconnected daily activities throughout the inside and outside of buildings and houses. Nowadays, pollutants from various sources are emitted, transformed by sunlight, vapor, and ozone and transported into the city from country to country. Due to these reasons, there have been high demands to monitor the transportation of particulate matters and improve air quality. Monitoring of pollutants and identification of type and its concentration enables us to track and control its generation and consequently find out the solution. However, monitoring of pollutants, especially, particulate matter generation and its transportation is still not fully operated in atmospheric air due to its open nature and meteorological factors. Even though indoor air is relatively easy to monitor and control than outdoor in the aspect of specific volume and contaminant source, but it still needs to consider the meteorological parameters because indoor air is not fully separated from the outdoor air flow and contaminants transportation. In this study, optical approach using spectral sensor was attempted to reveal the feasibility of wavelength and chromaticity values of reflected light from specific particles. From the analysis of reflected light of various particulate matters according to different liquid additives, parameter studies were performed to investigate which experimental conditions can contribute to the enhanced selective sensing of particulate matters. Five different particulate matters such as household dust, soil, talc powder, gypsum powder and yellow pine tree pollen were utilized and observed to elucidate the relationship between property of particulate matter and detected light spectrum. Applicable approaches to assist current particle matter sensors and improve the selective sensing were suggested.

The relative velocity between objects with finite velocity affects the reaction between them. This effect is known as general Doppler effect. The Laser Interferometer Gravitational-Wave Observatory (LIGO) discovered gravitational waves and found their speed to be equal to the speed of light c. Gravitational waves are generated following a disturbance in the gravitational field; they affect the gravitational force on an object. Just as light waves are subject to the Doppler effect, so are gravitational waves. This article explores the following research questions concerning gravitational waves: What is the spatial distribution of gravitational waves? Can the speed of a gravitational wave represent the speed of the gravitational field (the speed of the action of the gravitational field upon the object)? What is the speed of the gravitational field? Do gravitational waves caused by the revolution of the Sun affect planetary precession? Can we modify Newton’s gravitational equation through the influence of gravitational waves?

The purpose of this paper is to propose a novel transfer learning regularization method based on knowledge distillation. Recently, transfer learning methods have been used in various fields. However, the problems such as knowledge loss still occur during the process of transfer learning to a new target dataset. To solve these problems, there are various regularization methods based on knowledge distillation techniques. In this paper, we propose a transfer learning regularization method based on feature map alignment used in the field of knowledge distillation. The proposed method is composed of two attention based submodules: self-pixel attention (SPA) and global channel attention (GCA). The self-pixel attention submodule utilizes both the feature maps of the source and target models, so that it provides an opportunity to jointly consider the features of the target and the knowledge of the source. The global channel attention submodule determines the importance of channels through all layers, unlike the existing methods that calculate these only within a single layer. Accordingly, transfer learning regularization is performed by considering both the internal of each single layer and the depth of the entire layer. Consequently, the proposed method using both of these submodules showed overall improved classification accuracy than the existing methods in classification experiments on commonly used dataset.

Background: This study aimed to investigate the impact of the COVID-19 pandemic on breast reconstruction trends in the United States, focusing on implant-based and autologous techniques, as well as the timing of reconstruction (immediate vs. delayed). Methods: A retrospective analysis of data from the American Society of Plastic Surgeons' National Plastic Surgery Statistics from 2015 to 2022 was conducted. Annual trends in breast reconstruction procedures were analyzed, comparing the pre-pandemic (2015-2019) and pandemic (2020-2022) periods. Results: The total number of breast reconstructions increased from 106,338 in 2015 to 151,641 in 2022. The proportion of implant-based reconstructions decreased from 81.41% pre-pandemic to 76.51% during the pandemic (p < 0.001), with a notable rise in direct-to-implant procedures from 10.37% to 19.12% (p < 0.001). Autologous reconstructions increased from 18.59% to 23.49% (p < 0.001). Among autologous techniques, DIEP flaps remained the most popular. Immediate reconstruction rates increased from 72.61% pre-pandemic to 75.57% during the pandemic, while delayed recon-struction rates decreased from 27.39% to 24.43% (p < 0.001). Conclusions: The COVID-19 pandemic has significantly influenced breast reconstruction trends in the United States, with a shift towards autologous techniques, particularly DIEP flaps, and an in-crease in immediate reconstructions. These changes may reflect adaptations in surgical practice and decision-making processes in response to the unique challenges posed by the pandemic. Further research is needed to assess the long-term outcomes and patient satisfaction associated with these trends.

This paper proposes a novel approach called Multi-strategy Improved Chaotic Whale fused with Perturbation Observation method (IWOA-PO) for Maximum Power Point Tracking (MPPT) con-trol, to address the challenge of low efficiency in photovoltaic (PV) power generation under local shadows, according to the features of whale optimization algorithm (WOA) and perturbation observation (P&O) method. In the early stage of control algorithm, IWOA is used for global search to quickly locate the position of the Maximum Power Point (MPP). In the later stage of control algorithm, P&O is used for fine-grained local search to quickly, accurately and low oscillation track the position of the global maximum power point (GMPP). In order to verify the correctness, the tracking performance of IWOA-PO is comprehensively compared with WOA-PO、WOA、PSO under four conditions including uniform illumination, static partial shade, dynamic irradiance mutation and sudden changes in temperature and irradiance. In the above four conditions, the IWOA-PO algorithm has faster convergence and less power oscillations compared to the re-maining three algorithms, indicating that the IWOA-PO algorithm is effective. Finally, a physical verification experiment process is built to verify the correctness and effectiveness of the algorithm proposed in this paper.

In order to the effect of hydrated phase change materials on suppressing coal spontaneous combustion, the thermogravimetric experiment and reaction activation energy analysis experiment were used to explore the changes of combustion characteristic, parameters characteristic temperature and activating energy of gas coal, long flame coal, meagre coal, and lean coal before and after adding hydrated phase change materials. The research results showed that hydrated phase change materials increased the coal samples’characteristic temperature point and have effective inhibitory effects on different stages of oxidation process.However, the effect was best at low temperatures, as hydrated phase change materials undergo phase change and absorb heat when heated at low temperatures, isolating coal from contact with oxygen. The activating energy increased by 1.138 KJmol-1～23.048 KJmol-1 and the mass loss reduced by 1.6%～9.3% after the inhibition of the coal sample,indicating that the oxidation rate of various coal samples can be slowed down and the spontaneous combustion can be suppressed by using hydrated phase change materials.At the same time, this material can also reduce the combustibility index of meagre coal and lean coal, as well as the comprehensive combustion index and maximum loss rate of long flame coal and gas coal.

Angelica decursiva is one of the lending traditional Chinese medicinal plants producing coumarins. Notably, several studies have focused on the biosynthesis and not the qRT-PCR (quantitative real-time reverse transcription polymerase chain reaction) study of coumarins. This qRT-PCR technique has been extensively used to investigate gene expression levels in plants and the selection of reference genes which plays a crucial role in standardizing the data form the qRT-PCR analysis. In our study, 11 candidate reference genes were selected from the existing transcriptome data of Angelica decursiva. Here, four different types of statistical algorithms (geNorm, NormFinder, BestKeeper, and Delta Ct) were used to calculate and evaluate the stability of gene expression under different external treatments. Subsequently, RefFinder analysis was used to determine the geometric average of each candidate gene ranking, and to perform comprehensive index ranking. The obtained results showed that among all the 11 candidate reference genes, SAND family protein (SAND), protein phosphatase 2A gene (PP2A), and polypyrimidine tract-binding protein (PTBP) were the most stable reference genes, where Nuclear cap binding protein 2 (NCBP2), TIP41-like protein (TIP41), and Beta-6-tubulin (TUBA) were the least stable genes. To the best of our knowledge, this work is the first to evaluate the stability of reference genes in the Angelica decursiva which has provided an important foundation on the use of qRT-PCR for an accurate and far-reaching gene expression analysis in this medicinal plant.

This study aimed to overcome the difficulty of conducting the horizontal-well cavity leaching test in the field and to investigate the long-term stability of the horizontal-well salt-cavity natural gas storage. The simulation test design is combined with the similarity theory to study the cavity expansion characteristics and the influence law of cavity leaching parameters. Through the design of a rubber hose connection, an integrated closed test system for multi-stage horizontal-well cavity leaching and brine drainage was built. The test system also realises the repeatable backward movement of the injection well during the test. A similarity simulation of the test design was carried out, and the test platform was constructed to carry out multi-stage horizontal-well leaching tests with a nitrogen cushion. In the horizontal-well leaching tests with a nitrogen cushion, the influence laws of the well spacing, flow rate and liquid level position on cavity expansion were investigated. Based on the morphological characteristics of the horizontal-well cavity, a numerical model of the horizontal-well salt cavity was developed, which reflects the real cavity morphology leached in the test. The long-term stability of the horizontal-well salt-cavity natural gas storage under different internal pressures was investigated through numerical simulation.

We study the Gaudin models with gl(1|1) symmetry that are twisted by a diagonal matrix and defined on tensor products of polynomial evaluation gl(1|1)[t]-modules, extending all the results of to the twisted case. Namely, we give an explicit description of the algebra of Hamiltonians (Gaudin Hamiltonians) acting on tensor products of polynomial evaluation gl(1|1)[t]-modules and show that there exists a bijection between common eigenvectors (up to proportionality) of the algebra of Hamiltonians and monic divisors of an explicit polynomial written in terms of the highest weights and evaluation parameters. In particular, our result implies that each common eigenspace of the algebra of Hamiltonians has dimension one. We also give dimensions of the generalized eigenspaces.

Populations with essential hypertension have a high risk of nonalcoholic steatohepatitis (NASH). In this study, we investigated the mechanism that underlies the progression of hypertension-associated NASH by comparing differences in the development of high fat and cholesterol (HFC) diet-induced NASH among three strains of rats, i.e., two hypertensive strains comprising spontaneously hypertensive rats and the stroke-prone spontaneously hypertensive 5/Dmcr, and the original Wistar Kyoto rats as the normotensive control. We investigated histopathological changes and molecular signals related to inflammation in the liver after feeding with the HFC diet for 8 weeks. The diet induced severe lobular inflammation and fibrosis in the livers of the hypertensive rats, whereas it only caused mild steatohepatitis in the normotensive rats. Increased activation of proinflammatory signaling (transforming growth factor-β1/mitogen-activated protein kinases pathway) was observed in the hypertensive strains fed with the HFC diet. In addition, the HFC diet suppressed the nuclear factor erythroid 2-related factor 2 pathway in the hypertensive rats and led to lower increases in the hepatic expression of heme oxygenase-1, which has anti-oxidative and anti-inflammatory activities. In conclusion, these signaling pathways might play crucial roles in the development of hypertension-associated NASH.

The synchronization of complex networks is believed to be closely related to network topology. How to study synchronization of real network without clear topology and parameters? In this Letter, a synchronized stability boundary equation is derived that is system- and disturbance-independent and applicable to arbitrarily coupled grids. The results imply that spontaneous synchronization in a network may be network independent. These conclusions provide new research paths for network synchronization and analyze the synchronization stability of grids in a unified way.

Physical inactivity is a well-known risk factor for various non-communicable diseases (NCDs). Sufficient physical activity (PA) is essential for the prevention of NCDs and thus it is imperative to study the current status of PA and its influencing factors among rural residents in China. A population-based survey was conducted in rural areas of Shandong, Shanxi and Yunnan Provinces using a stratified random sampling method. The International Physical Activity Questionnaire Short Form (IPAQ-S) was used to collect the data on PA. A total of 3780 rural residents participated in the survey. The result showed that 22.2% of rural residents were physical inactivity. The proportion of rural residents reporting practice of physical exercise was 54.4%. The most frequently performed physical exercise was walking/brisk walking(78.3%).Binary logistic regression analyses showed that being female, people at age between 15 to 34 years or 60 years old and above, employees of governmental departments/retirees, school students, the unemployed, people with NCDs were risk factors of PA and ethnic minority groups,smoking and alcohol consumption were risk factors of physical exercise. Health promotion programme aiming at increasing people’s PA in rural China is needed and it should focus on the populations groups of the female, people at age 60 years and above ,school students, the unemployed, and people with NCDs.

With the outbreak of coronavirus disease 2019 (COVID-19), there is a need for efficient management of patients with mild or no symptoms, which account for the majority. The aim of this study is to introduce the structure and operation protocol of a living and treatment support centre (LTSC) operated by Seoul National University Hospital in South Korea. The existing accommodation facility was converted into a 'patient centre' where patients was isolated. A few Medical staff here performed medical tests and responded to emergencies. Another part of the LTSC was 'remote monitoring centre'. In this center, patients’ self-measured vital signs and symptoms were monitored twice a day, and the medical staff staying here provided video-consultation via a smartphone. During the 3 weeks from March 5 to March 26, 2020, 113 patients were admitted and treated. LTSC could be an efficient alternative to hospital admission in pandemic situation like COVID-19.

Theaflavins, the characteristic and bioactive polyphenols in black tea, possess the potential improvement effects on insulin resistance-associated metabolic abnormalities including obesity and type 2 diebetes. However, the molecular mechanisms of theaflavins improving insulin sensitivity are still not clear. In this study, we investigated the protective effects and mechanisms of theaflavins on palmitic acid-induced insulin resistance in HepG2 cells. Theaflavins could significantly increase glucose uptake of insulin-resistant cells at noncytotoxic doses. This activity was mediated by upregulating the glucose transporter 4 protein expression, increasing the phosphorylation of IRS-1 at Ser307, and reduced the phosphor-Akt (Ser473) level. Moreover, theaflavins were found to enhance mitochondrial DNA copy number through down-regulate the PGC-1β mRNA level and up-regulate PRC mRNA expression in insulin-resistant HepG2 cells. These results indicated that theaflavins could improve free fatty acid-induced hepatic insulin resistance by promoting mitochondrial biogenesis, and were promising functional food and medicines for insulin resistance-related disorders.

This study explores the public library service evaluation domain through user-generated content on Google Maps, highlighting digital feedback's significant yet underexplored potential in understanding public library patronage across Taiwan's six major cities. Utilizing a mixed-methods research design, this study integrates Google Maps review content analysis with Social Network Analysis to delineate public perceptions and identify areas for service enhancement in public libraries. It innovatively leverages personal experiences extracted from over 60,000 Google Maps reviews to evaluate public library services in cities such as Taipei, New Taipei, Taoyuan, Taichung, Tainan, and Kaohsiung. The research taps into the National Library of Taiwan's National Library Statistics System to provide a robust analysis of library performance and user satisfaction, offering a novel perspective by emphasizing user-centric feedback from Google Maps as a primary data source. This approach provides quantitative data on library usage and geographic distribution and enriches our understanding of the qualitative experiences of library users. In analyzing the keywords from Google Maps reviews of public libraries, we categorize and interpret these under the three core LibQUAL+ dimensions—Affect of Service, Information Control, and Library as Place. The findings expose variances in perceived service quality among the cities, with Kaohsiung and Taichung receiving the highest accolades for service satisfaction. Simultaneously, the study identifies potential areas for improvement, particularly in cities with lower satisfaction ratings like Taipei. This personalized feedback illustrates the intimate relationship between public libraries and their communities, offering invaluable insights for policymakers and library management to enhance service delivery and user experience.

With the growing demand for positioning services, angle-of-arrival (AoA) estimation or direction-finding (DF) has been widely investigated for applications in fifth-generation (5G) technologies. Many existing AoA estimation algorithms only require the measurement of the direction of the incident wave at the transmitter to obtain correct results. However, for most of the cellular systems such as Bluetooth indoor positioning system due to multipath and non-line-of-sight (NLOS) propagation, the indoor positioning accuracy is severely affected. In this paper a comprehensive algorithm is investigated that combines radio measurements from Bluetooth AoA local navigation systems with indoor position estimates obtained using particle filtering, which allows us to explore new optimised methods to reduce estimation errors in indoor positioning. First, particle filtering is used to predict the rough position of a moving target. Then, an algorithm with robust beam weighting is used to estimate the AoA of the multipath components. Based on this, a system of pseudo-linear equations for target positioning based on the probabilistic framework of PF and AoA measurement is derived. Theoretical analysis and simulation results show that the algorithm can improve the positioning accuracy by about 25.7% on average.

Reciprocal Personal/Public Protection (RPPP) featured with source control is introduced, Mask Discriminating Mouth and Nose (MDMN) is employed to serve the purpose, which includes polymer based mouth cover with optional nose cover. The new knowledge that mouth is a primary, active and dominant source of the virus has been well established, which is the base of MDMN. Source classification and related source control tools are discussed, mouth cover is recommended as the tool prioritized to use. Liquid droplets is identified as a hard issue related to mask, liquid droplets, mask fitting, comfort and facial recognition constitute real challenges of mask in addition to efficiency, All of these have been addressed with MDMN. Comparisons between MDMN and masks/face covering are taken on four aspects: efficiency and efficacy, tolerance and comfort, cost and waste, and civil rights and public interest. Mouth cover is recommended to replace the face covering and act as both a personal tool and a public utensil, mouth cover with nose cover can provide better protection than N95 etc. RPPP with MDMN, could be an alternative for lockdown, a parallel strategy to vaccine, and a collectively living way during the pandemic era. MDMN, featured with high efficiency protection, high degree comfort, easy wearing, tight-fitting, easy facial recognition & communication, reusability, cost-effective, environment friendly and scale manufacturing more readily and widely etc., is a simple and sustainable solution, which is essential for ordinary people to keep wearing it properly for protection.

Aiming to reveal the kinetic characteristics of ceramic ball grinding of fine magnetite comprehensively, two types of ceramic balls ground with the same filling rate and total weight as steel balls were researched. The results show that the breakage rate of ceramic ball grinding is only half of that of steel ball grinding with the same media filling rate. With the same total media weight and the feed size less than 0.212 mm, the breakage rate of the ceramic ball grinding approaches the steel ball grinding and is 21.43% higher than that of the steel ball grinding. The main crushing form of magnetite changed from impact to abrasion in ceramic ball grinding compared with steel ball grinding, which significantly affected the value of the zero-order output constant a. Consequently, there is a noticeable difference in the variation of the parameter β related to the fines generation rate of the ceramic ball grinding compared with the steel ball grinding.

High-efficiency rock breaking by hydraulic jetting is the key to radial horizontal drilling technology. In order to improve the drilling efficiency of hydraulic jet rock breaking in radial horizontal wells, based on LS-Dyna display dynamics, a numerical simulation model of single nozzle jet rock breaking is established to analyze the influence of different nozzle parameters on rock breaking effect. Then, the numerical simulation model of the spin multi-nozzle jet bit is established, and the influence of different rotation speeds on the rock breaking effect of the jet bit is analyzed. Finally, the rock breaking drilling characteristics of the spin multi-nozzle jet bit and the conventional multi-nozzle jet bit are compared and analyzed. The results show that when the jet impacts the rock surface, the larger the inclination angle is, the larger the rock breaking width formed by the jet is. The smaller the dip angle, the greater the rock breaking depth. When the inclination angle is greater than 60 °, it is difficult to meet the needs of reaming. The width and depth of the nozzle gradually increase with the increase of the diameter. When the nozzle diameter is greater than 1.3mm, the growth rate of rock breaking depth begins to decrease. The optimum nozzle diameter is 1.3 mm. When v = 50m / s, the damage caused by the jet to the rock surface is very small, because the condition of rock fracture is not reached at this time. This shows that there is a critical value of the water jet impact velocity, and only when the velocity is reached, the rock will break. When the velocity is v = 150m / s, v = 200m / s, v = 250m / s, v = 300m / s, the rock breaks. At the same time, the higher the speed, the higher the degree of rock fracture, the greater the fracture depth, the greater the fracture area, the better the fracture effect. The tangential and radial velocity of the jet increases the shear and tensile failure rate of the sample, and improves the rock breaking efficiency of the jet, which has certain guiding significance for improving the rock breaking drilling efficiency of radial horizontal well drilling.

Dislocation is one of the major challenges in unmanned aerial vehicle (UAV) image stitching. In this paper, we propose a new dynamic programming for seamlessly stitching UAV images using optical flow. Our solution consists of two steps: Firstly, an image-matching algorithm is used to correct the images so that they are in the same coordinate system. Secondly, a new dynamic programming algorithm is develop based on the concept of a stereo dual-channel energy accumulation using optical flow. A new energy aggregation and traversal strategy is adopted in our solution, which can find a more optimal seam line for adjacent image stitching. Our algorithm overcomes the theoretical limitation of the classical Duplaquet algorithm. Experiments show that the algorithm can effectively solve the dislocation problem in UAV image stitching. Beyond that, our solution is also direction-independent, which has more adaptability and robustness for UAV images.

The increasing prevalence of obesity and sedentary lifestyles has led to an increased incidence of metabolic syndrome (MetS) worldwide. In Taiwan, middle-aged women are at a greater risk of MetS, type 2 diabetes, and cardiovascular disease than men are because they have more subcutaneous fat and larger waist circumferences compared to men with equal visceral fat levels. This study investigated the effects of calorie restriction supplemented with fish oil (CRF) in middle-aged women with MetS. For 12 weeks, 75 eligible participants were randomly assigned either calorie restriction (CR) or CRF. Both dietary intervention groups were further divided into two age groups: ≤45 and >45 years. The changes in MetS severity, inflammatory status, iron status, and red blood cell fatty acid profile were evaluated. Seventy-one participants completed the trial. Both dietary interventions significantly ameliorated MetS and improved the participants’ inflammatory status. CR significantly increased total iron binding capacity, whereas CRF increased hepcidin levels. Furthermore, CRF significantly increased the n-6/n-3 and arachidonic acid/docosahexaenoic acid ratios. In conclusion, CR and CRF improved the anthropometric and MetS characteristics of early-middle aged women, including body weight, blood glucose levels, triglyceride levels, as well as the scores for the homeostasis model assessment of insulin resistance and quantitative insulin sensitivity cheque index. Dietary intervention was more effective in >45-year-old women than ≤45-year-old women.

Blood image intensity has been used to detect erythrocyte sedimentation rate (ESR). However, it does not give an information on biophysical properties of blood sample under continuous ESR. In this study, three physical properties, including, τ₀, ESR_τ, and AI_I, are suggested to quantify mechanical variations of blood under continuous ESR. To demonstrate the proposed method, blood sample is loaded into a driving syringe. The blood flow rate is set in a periodic on–off pattern. Blood sample is then supplied into a capillary chip, and microscopic blood images are captured at specific intervals. Blood shear stress is quantified from the interface of blood stream in the coflowing channel. Both τ₀ and ESR_τ are then obtained by analyzing the blood shear stress. Simultaneously, the AI_I is evaluated by analyzing the image intensity of blood flow. According to the experimental results, the τ₀ exhibits consistent trends with respect to hematocrit as well as diluent. The ESR_τ and AI_I showed a reciprocal relationship each other. Three suggested properties represented substantial differences for suspended blood samples (i.e., hardened red blood cells, different concentration of dextran solution and fibrinogen). In conclusion, the present method can detect variations of blood sample under continuous ESR effectively.

Although Darwin‘s evolutionary mutation theory has been widely accepted, many endeavors have been tried to challenge it. With more and more observation of successful hybridization and hybrids, the sexual isolation between species has become vague. The mechanism of evolution has been expanded from the classical model of evolution to multiple routes of speciation. Furthermore, a fundamental crossbreeding theory has been raised and proved by two lines of evidences: paleopolyploidy and fan-shaped spectrum of species. Ancient genome duplications are widespread throughout eukaryotic lineages, particularly in plants. The genome polyploidization, especially in the somatic cell hybridization, can break through the sexual incompatibility between diploid counterparts to hybridize and produce new species. By comparing characteristics, all species in every taxon, both in the extinct fossil and extant organisms, can be arranged into fan-shaped spectrum according to their similarity: left primitive type-middle advanced type-right primitive type. The species are primitive at the two ends and advanced at the middle. The primitive two species always resemble two types of more primitive species that can be confirmed as their ancestors respectively, and the middle species is half similar to the two ancestors respectively. These suggest that the species in the spectrum come from two different ancestors by crossbreeding and gene combination. As a sum, advanced species originated from crossbreeding of two primitive ancestors, by major method of polyploidization, and proved by results of fan-shaped spectrum of species. Then, sex is the cause, force and opportunity for evolution.

The cortical motor system can be reorganized following a stroke, with an increasing recruitment of the contralesional hemisphere. However, it is unknown whether a similar hemispheric shift occurs in the somatosensory system to adapt to this motor change, and whether this is related to movement impairments.  This proof-of-concept study assessed somatosensory evoked potentials (SEPs), P50 and N100, in hemiparetic stroke participants and age-matched controls using high-density electroencephalograph (EEG) recordings during tactile finger stimulation. The laterality index was calculated to determine hemispheric dominance of the SEP and re-confirmed with source localization.  The study found that latencies of P50 and N100 were significantly delayed in stroke brains when stimulating the paretic hand. The amplitude of P50 was negatively correlated with Fügl-Meyer Upper Extremity Motor Score in stroke. Bilateral cortical responses were detected in stroke, while only contralateral cortical responses were shown in controls, resulting in a significant difference in the laterality index.  These results suggested that somatosensory reorganization after stroke involves increased recruitment of ipsilateral cortical regions. This reorganization delays the latency of somatosensory processing after a stroke.  This research provided new insights related to the somatosensory reorganization after stroke, which could enrich future hypothesis-driven therapeutic rehabilitation strategies from a sensory or sensory-motor perspective.

Parasitic diseases continue represent a threat on a global scale, particularly among the poorest countries in the world. This is particularly because of the absence of vaccines, and in some cases, resistance against available drugs, currently being used for their treatment. In this review emphasis is laid on natural products and scaffolds from African medicinal plants (AMPs) for lead drug discovery and possible further development of drugs for the treatment of parasitic diseases. In the discussion, emphasis has been laid on alkaloids, terpenoids, quinones, flavonoids and narrower compound classes of compounds with micromolar range activities against Schistosoma, Trypanosoma and Leishmania species. Suggestions for future drug development from African medicinal plants have also been provided.

The emergence of CDK4/6 inhibitors, such as palbociclib, ribociclib, and abemaciclib, has revolutionized the treatment landscape for hormone receptor-positive breast cancer. These agents have demonstrated significant clinical benefits in terms of both progression-free survival and overall survival. However, resistance to CDK4/6 inhibitors remains a challenge, limiting their long-term efficacy. Understanding the complex mechanisms driving resistance is crucial for the development of novel therapeutic strategies and improvement of patient outcomes. Translational research efforts, such as preclinical models and biomarker studies, offer valuable insight into resistance mechanisms and may guide the identification of novel combination therapies. This review paper aims to outline the reported mechanisms underlying CDK4/6 inhibitor resistance, drawing insights from both clinical data and translational research in order to help direct the future of treatment for hormone receptor positive metastatic breast cancer.

The Eastern Himalayan Syntaxis (EHS), featured by an exceptionally intense compression orogeny and an extremely rapid surface erosion rate, stands out as a prime area for investigating surface processes and landscape evolution. Understanding the formation of the EHS holds significant importance in advancing our comprehension of the evolutionary dynamics within the Tibetan Plateau and the complex interplay between endogenic and exogenic geological processes. Currently, two models, namely the tectonic aneurysm and the syntaxis expansion model, have been proposed to explain the formation and evolution of this syntaxis. In this study, we employ a multi-disciplinary approach, integrating geomorphic indices such as slope, relief, Hypsometric Integral (HI), Normalized Channel Steepness (Ksn), River Slope-Basin Area Integration (χ), combined with erosion rates on long-medium-short term timescales obtained from thermochronology, cosmogenic nuclides 10Be and landslide disaster probability data. Our findings suggest a relatively high tectonic activity in the confluence of the Yigong and Parlung Rivers in the northern end of the syntaxis. Moreover, our data reveals that spatial variability of tectonic activity is the primary driver of regional geomorphologic features and the spatial-temporal characteristics of erosion observed in the EHS, with lithology and climatic precipitation playing a lesser role. Furthermore, the northwards migration of the EHS appears to elucidate the shift of tectonic activity and rapid erosion from the core of the syntaxis near the Namche Barwa towards the confluence of the Yigong and Parlung Rivers. This northwards migration of the EHS underscores the need for increased attention to the high geological hazard risk in the northern part of the EHS.