The quantified residence time distribution (RTD) provides a numerical characterization of mixing in the continue casting tundish, thus allowing the engineer to better understand the metallurgical performance of the reactor. This paper describes a computational fluid dynamic (CFD) modelling study for analyzing the flow pattern and the residence time distribution in a five-strand tundish. Two passive scalar transport equations are applied to separately calculate the E-curve and F-curve in the tundish. The numerical modelling results are compared to the water modelling results for the validation of the mathematical model. The volume fraction of different flow regions (plug, mixed and dead) and the intermixing time during the ladle changeover are calculated to study the effects of the flow control device (FCD) on the tundish performance. The result shows that a combination of the U-baffle with deflector holes and the turbulence inhibitor has three major effects on the flow characteristics in the tundish: i) reduce the extent of the dead volume; ii) evenly distribute the liquid streams to each strand and iii) shorten the intermixing time during the ladle changeover operation.

Wind power generation is one of the mainstream renewable energy resources. Voltage stability is as important as the frequency stability of a power system with a high penetration of wind power generation. The advantages of high-voltage direct current (HVDC) transmission systems become more significant with the increase of both installed capacity and transmission distance in offshore wind farms. Therefore, this study discusses about various voltage control methods for wind turbines and HVDC transmission systems. First, various voltage control methods of a wind farm were introduced, and they include QV control and voltage droop control. The reactive power of a wind turbine varies with active power, while the active power from each wind turbine may be different owing to wake effects. Thus, QV and voltage droop control with varying gain values were also discussed in this paper. Next, the voltage control methods for a HVDC transmission system, such as power factor control, voltage control, and Vac-Q control, are also summarized and tested in this study. When a three-phase short circuit fault occurs or a suddan reactive power load increases, the system voltage would drop immediately. Thus, various voltage control methods for wind turbines or HVDC can make the system's transient response more stable. Therefore, this study implemented the simulation scenarios, including a three-phase short circuit fault at the point of common coupling (PCC) or a sudden increase of reactive power load, and adopted various voltage control methods, which aims to verify whether additional voltage control methods are effective to improve the performance of transient voltage.

The quality of digital elevation models (DEMs) is inevitably affected by the limitations of the imaging modes and the generation methods. One effective way to solve this problem is to merge the available datasets through data fusion. In this paper, a fusion-based global DEM dataset (82°S-82°N) is introduced, which we refer to as GSDEM-30. This is a 30-m DEM mainly reconstructed from the unfilled SRTM1, AW3D30, and ASTER GDEM v2 datasets combining the multi-source and multi-scale fusion techniques. A comprehensive evaluation of the GSDEM-30 data, as well as the 30-m ASTER GDEM v2 and AW3D30 DEM, was presented. Global ICESat GLAS data and the local National Elevation Dataset (NED) were used as the reference for the vertical accuracy validation, while GlobeLand30 was introduced for the landscape analysis. Furthermore, we employed the maximum slope approach to detect the potential artefacts in the DEMs. The results show that the GDEM data are seriously affected by noise and artefacts. With the advantage of the multiple datasets and the refined post-processing, the GSDEM-30 are contaminated with fewer anomalies than both ASTER GDEM and AW3D30. The fusion techniques used can also be applied to the reconstruction of other fused DEM datasets.

Super-Resolution Microscopy enables non-invasive, molecule-specific imaging of the internal structure and dynamics of cells with sub-diffraction limit spatial resolution. One of its major limitations is the requirement for high-intensity illumination, generating considerable cellular phototoxicity. This factor considerably limits the capacity for live-cell observations, particularly for extended periods of time. Here, we overview new developments in hardware, software and probe chemistry aiming to reduce phototoxicity. Additionally, we discuss how the choice of biological model and sample environment impacts the capacity for live-cell observations.

The plate embedded with acoustic black hole (ABH) indentations is potential for structural vibration and noise control. This work focuses on the mid- and low-frequency performance of plates embedded with the array of ABH for energy focalization and vibration & noise suppression. Plates embedded with two-dimensional ABHs are modelled with detailed Finite Element (FE) models, and the power flow method is introduced to analyze the energy propagation characteristics arising from ABH effect. Then the distribution of average vibration power density along ABH radius is studied. Next, the energy dissipation effects of the plate model embedded with ABH array with two types of damping layers are investigated. Finally, the sound pressure levels of the ABH structure are calculated and discussed. This work is helpful to understand the characteristics of plates embedded with ABH array in reducing vibration and noise radiation. Results show the tremendous potential of ABH array for vibration and noise control.

Seven pieces of Lacquer Lian from Warring States Period to Yuan Dynasty were analyzed by means of cross-section observation, Raman spectroscopy (RS) and thermally assisted hydrolysis and methylation pyrolysis coupled with gas chromatography/ mass spectroscopy (THM-Py-GC/MS). The results demonstrate that Lacquer Lian was consisted by three layers, including pigment layer, undercoat layer and ground layer, and lacquering techniques had undergone minimal changes from Warring States Period to Yuan Dynasty, the red mineral pigment was cinnabar, the lacquer sap was urushi. Furthermore, Boiled tung oil was found in the ground layer of lacquerwares from Song Dynasty and Yuan Dynasty.

With the rapid development of China's economy, construction industrialization has become the main development trend of China's construction industry, and the convenient, efficient, environmental protection has become the new fashion, therefore the application of prefabricated building is more and more common. Stair serves as the weak link in prefab type building, the connecting node has an important influence on its failure. In this paper, pseudo-static tests are carried out on the joints in different forms of ladder holes to study the mechanical properties of flexible hinge points filled with flexible materials, and the hysteresis curve, skeleton curve and bearing capacity of each specimen are analyzed. The test results show that the flexible hinge can give full play to its flexible characteristics to ease the stress of ladder beam, pin bolt reinforcement and ladder hole, and the bearing capacity of flexible hinge points is moderate, which can not only mitigate the inclined bracing effect under the action of small and medium earthquakes, but also ensure the stair does not fall off under the action of large earthquakes. Through the experiment comparison, the ladder hole adopts node form 2, which can give full play to the advantage of flexible material.

Plant endophytic fungi and rhizosphere soil fungi are often reported as biocontrol agents against plant pathogens or with plant growth promotion potential. Four treatments were performed in field and greenhouse experiments where cucumber plants were inoculated with Trichoderma harzianum and Fusarium oxysporum in 2022. The roots, stems and leaves of cucumber plants and their rhizosphere soil were collected twice individually from the field and greenhouse for isolation of cucumber endophytic and rhizosphere soil fungi. All 74 genera and 1275 fungal strains were sequenced by rDNA ITS. The PDA media yielded the highest number of genera isolated from cucumber plants, rhizosphere soil and both compared to other media. There were no significant differences among the 4 media for the isolation of cucumber endophytic fungi. The best media for isolating fungi from roots and stems were MRBA and PDA, respectively. PDA and CZA had higher isolation efficiency for the rhizosphere soil fungi than MRBA. The 28 fungal genera had high isolation efficiency, and the endophytic Trichoderma strains were best isolated by MEA. It is suggested that PDA can be used as a basic medium, and different media can be considered for specific fungal genera.

Aborycin is a type I lasso peptide with a stable interlocked structure, offering a favorable framework for drug development. The aborycin biosynthetic gene cluster gul from marine sponge-associated Streptomyces sp. HNS054 was cloned and integrated into the chromosome of S. coelicolor hosts with different copies. The 3-copy gul-integration strains S. coelicolor M1346::3gul showed better production than one-copy or 2-copy gul-integration strains, and the total titer reached approximately 10.4 mg/L, i.e., 2.1 times that of the native strain. Then, five regulatory genes, phoU (SCO4228), wblA (SCO3579), SCO1712, orrA (SCO3008) and gntR (SCO1678), which were reported to have negative effects on secondary metabolism, were further knocked out from the M1346::3gul genome by CRISPR/Cas9 technology. While the ΔSCO1712 mutant showed a significant decrease (4.6 mg/L) and the ΔphoU mutant showed no significant improvement (12.1 mg/L) in aborycin production, the ΔwblA, ΔorrA and ΔgntR mutations significantly improved the aborycin titers to approximately 23.6 mg/L, 56.3 mg/L and 48.2 mg/L, respectively, which were among the highest heterologous yields for lasso peptides in both Escherichia coli systems and Streptomyces systems. Thus, this study provided important clues for future studies on enhancing antibiotic production in Streptomyces systems.

In this paper, the effects on the rheological properties, particle size distribution, and fluorescence properties of red wine were investigated under microwave irradiation, and the mechanism of the effects of microwave irradiation on the sensory properties of red wine was discussed. The results showed that the effect of microwave on the rheological properties in red wine could be fitted by the Power-law model and Carson model, through the analysis of the rheological constants, yield stress, and viscosity coefficient of wine, it was found that microwave treatment could improve leg phenomenon and thickening effect by the change of rheological properties; the particle size distribution in wine indicated that microwave irradiation did change the particle size distribution through friction effect and oxidative polymerization, resulting in the wine’s visual effect and mouthfeel; the wine quality could be improved by enhancing the fluorescence intensity under different microwave conditions, which meant that microwave technology could speed up the formation of fluorescent substances, such as the polymerization of flavan-3-ols. In conclusion, microwave treatment could modify the sensory characteristics of wine, and further provide the theoretical basis for the application of microwave in winemaking.

Seven pieces of Lacquer Lian from Warring States Period to Yuan Dynasty (475 BC- 1368 AD) were analyzed by means of cross-section observation, Raman spectroscopy (RS) and thermally assisted hydrolysis and methylation pyrolysis coupled with gas chromatography/ mass spectroscopy (Py-GC/MS). The results demonstrated that Lacquer Lian was consisted by three layers, including pigment layer in the surface, undercoat layer in the middle and ground layer, the red mineral pigment was cinnabar, and mixture of Chinese lacquer and drying oil was applied as main organic materials. Although lacquering techniques had undergone minimal changes from Warring States Period to Yuan Dynasty, the species of drying oil had changed based on the fact that boiled tung oil was found in the ground layer of lacquerwares from Song Dynasty and Yuan Dynasty. The present research provided direct evidence for the inheritance and development of Chinese lacquer technology.

Glycosaminoglycans (GAGs) with unique structures from marine animals show intriguing pharmacological activities and negligible biological risks, providing more options for us to explore safer agents. Swim bladder is a tonic food and folk medicine, and its GAGs show good anticoag-ulant activity. In this study, two GAGs SJG-1.0 and GMG-1.0 have been extracted and isolated from the swim bladder of Sphyraena jello and Gadus morhua. The physicochemical properties, pre-cise structural characteristics, and anticoagulant activities of these GAGs were determined. The analysis results of the SJG-1.0 and GMG-1.0 showed that they were chondroitin sulfate (CS)/dermatan sulfate (DS) hybrid chains with molecular weights of 109.32 kDa and 123.13 kDa, respectively. They were mainly composed of the repeating disaccharide unit of -{IdoA-α1,3-GalNAc4S-β1,4-}- (DS-A). The DS-B disaccharide unit of -{IdoA2S-α1,3-GalNAc4S-β1,4-}- also existed in both SJG-1.0 and GMG-1.0. SJG-1.0 had a higher proportion of CS-O disaccharide unit -{-GlcA-β1,3-GalNAc-β1,4-}-, while GMG-1.0 contained higher proportion of CS-E disaccha-ride unit -{-GlcA-β1,3-GalNAc4S6S-β1,4-}-. The disaccharide compositions of the GAGs varied in a species-specific manner. Anticoagulant activity assay revealed that both SJG-1.0 and GMG-1.0 had potent anticoagulant activity, which can significantly prolong activated partial thrombosis time. GMG-1.0 also can prolong the thrombin time. SJG-1.0 showed no intrinsic tenase inhibition ac-tivity, while GMG-1.0 can obviously inhibit intrinsic tenase with EC50 of 58 nM. Their significantly different anticoagulant activities may be due to their different disaccharide structural units and proportions. These findings suggested that the swim bladder CS/DS hybrid chains with well-defined structure may be safer anticoagulants with low bleeding risk.

Five new cembrane-type diterpenes, lobocalines A–E (1–5), and four new steroids, lobocalines F–I (9–12), along with six known related compounds (6–8 and 13–15) were isolated from the Yalong Bay soft coral Lobophytum catalai. The structures of the new compounds were elucidated by extensive spectroscopic analysis, NMR calculation with DP4+ analysis, time-dependent density functional theory-electronic circular dichroism (TDDFT-ECD) calculations, X-ray diffraction analyses, and the comparison with the reported spectroscopic data of known compounds. Further, with the aid of X-ray diffraction analysis, the structure of lobocrasol B (15) was firmly revised as 15a. In in vitro bioassays, compound 2 showed moderate antibacterial activities against fish pathogenic bacteria Streptococcus parauberis KSP28 and Phoyobacterium damselae FP2244 with minimum inhibitory concentration (MIC) values of 8.7 and 17.3 µg/mL, respectively. All the steroids exhibited antibacterial activities against the S. parauberis KSP28 with MIC values ranging from 12.3 to 53.6 µg/mL. Compounds 2, 7 and 14 have remarkable inhibitory effects on the hemolysin production of Staphylococcus aureus, while compounds 8–12 have medium inhibitory effects on the pyocyanin production in Pseudomonas aeruginosa.

In recent years, two-dimensional (2D) materials have attracted significant attention due to their distinctive properties, including exceptional mechanical flexibility and tunable electronic properties. Via the first-principles calculation, we investigate the effect of strain on the electronic properties of monolayer SnP2S6 and GeP2S6. We find that monolayer SnP2S6 is an indirect band gap semiconductor, while monolayer GeP2S6 is a direct band gap semiconductor. Notably, under uniform biaxial strains, SnP2S6 undergoes an indirect-to-direct band gap transition at 4.0% biaxial compressive strains, while GeP2S6 exhibits a direct-to-indirect transition at 2.0% biaxial tensile strain. The changes of the conduction band edge can be attributed to the high-symmetry point Γ being more sensitive to strain than K. Thus, the relocation of the conduction-band and valence-band edges in monolayer SnP2S6 and GeP2S6 induces a direct-to-indirect and indirect-to-direct band-gap transition respectively. Consequently, the strain is an effective band engineering scheme which is crucial for the design and development of next-generation nanoelectronic and optoelectronic devices.

The accurate assessment and monitoring of soil erosion is of great significance for guiding food production and ensuring ecological security, and it is a current research hotspot. In this paper, remote sensing and geographic information systems (GISs) are combined with the Revised Universal Soil Loss Equation (RUSLE model) to carry out research on soil erosion monitoring and make a quantitative evaluation. According to five factors, including rainfall erosivity, soil erodibility, topography, vegetation cover, crop management and water and soil conservation measures, the distribution of the soil erosion rate in Jilin Province in 2019 was mapped, and the soil erosion rate was divided into 5 levels according to the degree of erosion, including very slight, slight, moderate, severe and extremely severe erosion. Based on the segmented S-slope factor model and the unique topographical features of the study area, the relationships among the soil erosion rate, erosion risk level, erosion area, erosion amount and slope angle (θ) were systematically analysed, and a slope angle of 15° was identified as the threshold for soil erosion on sloped farmland in Jilin Province. The total soil erosion in Jilin Province was 402.14×106 t in 2019, the average soil erosion rate was 21.6 t·ha-1·a-1, and the average soil loss thickness was 1.6 mm·a-1; these values were far greater than the soil erosion rate risk threshold of 10 t ·Ha-1·a-1. Thus, the province has a strong level of soil erosion. We conclude that soil degradation is accelerating, and food production and the ecological environment will face severe challenges. It is suggested that soil erosion control should be carried out according to different types and slopes of land, with an emphasis on the management of forestland and farmland because forestland and farmland are currently the first types of land to be managed in Jilin Province. This paper aims to explore a timely, fast, efficient and convenient soil erosion monitoring and evaluation method and provide effective monitoring tools for agricultural water and soil conservation, ecological safety management and stable food production in Jilin Province and similar black soil areas.

The energy E takes the place of the gravitational mass m_G to produce gravity [1]. We wonder whether the inertial mass m_i in the inertial force is also replaced by E. The experiments to measure the inertial force and weight of a carrier are presented. Now we can test the principle of equivalence and study foundations of physics in condensed matter.

Omicron variants have higher infectivity, more immune escape but lower risk of severe clinical outcomes than the ancestral variants. However, people are still wondering whether SARS-CoV-2 may become lethal again or whether some highly-pathogenic strain may emerge in the future. Omicron is more selective proliferation in the upper respiratory tract (URT). The temperature of human URT is 33–34°C, and the virus strains other than Omicron cannot replicate effectively at this temperature. While Omicron adapted to the low temperature environment, so its distribution mainly depends on the expression levels of ACE2 in cells. Similar distribution switch from lungs to URT has been observed for the 1918 H1N1 influenza virus, who vanished after 1921 and has been turned to be the seasonal human influenza A viruses. However, some relatively high-pathogenic SARS-CoV-2 strains and influenza-virus strains may still emerge in the future. Dynamic changes in the viral virulence should be monitored constantly.

Body-centered cubic bismuth (Bi) is considered an enticing pressure marker, and therefore it is highly desirable to command its accurate equation of state (EOS). However, significant discrepancies are noted among the previous experimental EOSs. In the present work, the EOS up to 300 GPa is theoretically obtained by direct solving the partition function via a direct integral approach (DIA). The calculated results nearly reproduce the hydrostatic experimental measurements below 75 GPa, and the deviations from the measurements gradually get larger with increasing pressure. Based on the ensemble theory of equilibrium state, DIA works with high precision particularly in high-pressure conditions, so the hydrostatic EOS presented in this work is expected to be a reliable pressure standard.

After the end of colonial rule in 1997, the Hong Kong education system has been experiencing a policy reform on Senior Secondary Education (NSS) Curriculum commenced in September 2009 aiming to educate students as globalized Hong Kong citizens for the Western. Although previous scholars argued that it is hard to differentiate between domestic values and the Western values in account of curriculum development (Sewpaul, 2007), this study demonstrates an analysis using the dichotomy to investigate how local curriculum, especially in the post-colonial areas, embrace both the Western values and domestic values. Using content analysis on the NSS curriculum guides, this article evaluates the influence of the Western values and Chinese values in the NSS curriculum through investigating: (1) how the Western values and Chinese values was incorporated into the curriculum throughout its development (2) why some values are more significantly highlighted in the curriculum guide. Findings include that more Chinese values are involved in the curriculum documents. This may be because of the upholding of domestic values as a post-colonial city. The Western values which are academically related are greatly incorporated into the local curriculum.

This paper describes the formulations for viscoplasticity of metals based on the Chaboche and Delobelle model. The implementations of the viscoplastic models were detailed herein and then implemented via user subroutines for material models (UMAT) in ABAQUS. Two typical metals, i.e., 316 Stainless Steel and Zircaloy-4, were chosen as examples and their viscoplastic behaviors were captured. Numerical simulations are compared to reported experiments to validate the models and the UMAT codes. Typical viscoplastic behaviors of both metals, such as stress relaxation and creep, were captured well against available experiments. We publicize all the data and codes via: https://github.com/XJTU-Zhou-group/ABAQUS_UMAT_316ss_Zr4.

This paper considers the Hermitian solutions of a new system of commutative quaternion matrix equations, we establish both necessary and sufficient conditions for the existence of solutions. Furthermore, we derive an explicit general expression when it is solvable. To illustrate our main findings, we present two numerical algorithms and examples in this paper.

The gravitational charge should be the energy instead of mass. This modification will lead to some different results and the experiments to test are also presented. Especially, we propose a scheme to achieve the negative energy and gravitational repulsive force in the lab.

The relative velocity between objects with finite velocity affects the reaction between them. This effect is known as general Doppler effect. The Laser Interferometer Gravitational-Wave Observatory (LIGO) discovered gravitational waves and found their speed to be equal to the speed of light c. Gravitational waves are generated following a disturbance in the gravitational field; they affect the gravitational force on an object. Just as light waves are subject to the Doppler effect, so are gravitational waves. This article explores the following research questions concerning gravitational waves: What is the spatial distribution of gravitational waves? Can the speed of a gravitational wave represent the speed of the gravitational field (the speed of the action of the gravitational field upon the object)? What is the speed of the gravitational field? Do gravitational waves caused by the revolution of the Sun affect planetary precession? Can we modify Newton’s gravitational equation through the influence of gravitational waves?

Predicting and evaluating the vitality level of public spaces of urban design is crucial before new construction and renewal, especially for developing countries, to avoid failures like "ghost neighborhood" and reduce resource waste. However, existing assessment methods for the urban vitality are either static and ignore changes in the time dimension, or rely on historical big data and are unable to predict unbuilt projects. This study combines previous methods and crowds’ characteristics observation in public space, puts forward the crowd-frequency hypothesis and constructs an algorithm, and establishes a time-dimensional urban vitality dynamic prediction model. Taking the Rundle Mall neighborhood in Adelaide, Australia, as an example, the effec-tiveness of the prediction model was proved through on-site observation sampling comparative verification method. In addition, the decision tree model was used to conduct machine learning on the case data, and a set of algorithm programs were obtained that can directly input some basic information to obtain the urban vitality level (high-medium-low) in a certain period. It can be used as a tool to support the design and decision-making processes of urban planners and government officials, providing a low-cost way to achieve sustainable urban vitality construction of late-developing cities directly.

Reactions of Co(OAc)24H2O, N‚N'-bis(3-pyridylmethyl)oxalamide (L) and 4,4’-sulfonyldibenzoic acid (H2SDA) afforded four coordination polymers with the same mixed ligands, {[Co(L)(SDA)(H2O)2]·H2O·CH3OH}n, 1, {[Co(L)0.5(SDA)]·2H2O·0.5L}n, 2, {[Co(L)1.5(SDA)(H2O)]·H2O}n, 3, and {[Co2(L)1.5(SDA)2(H2O)2]·4H2O}n, 4, which have been structurally characterized by using single crystal X-ray crystallography. Complexes 1 – 4 are 2D layers, revealing the topologies of sql, 2,6L1, (4,4)Ia and 6L12, respectively, and demonstrating that the metal to ligand ratio, solvent system and reaction temperature are important in determining the structural diversity. Immersion of these complexes into various solvents show that the structural types govern the chemical stabilities of 1 – 4. Reversible structural transformation can be shown for complexes 1 and 2 upon solvent removal and adsorption, while those of 3 and 4 are irreversible.

Marine soft corals are prolific sources of various natural products that have served as a wealthy reservoir of diverse chemical scaffolds for new drug leads. The genus Litophyton contains almost 100 species but only a small part of them had been classified and chemically investigated, which calls for more attentions from the global researchers. In the current work, 109 secondary metabolites have been discussed based on published data from 1975 to July, 2023, covering a period of near five decades. The studied species of the genus Litophyton inhabited various tropical and temperate regions and afforded a variety of biologically active natural products such as terpenes, steroids, alkaloids, and lipids. A wide spectrum of pharmacological effects of these compounds had been evaluated, including cytotoxic, anti-HIV, antibacterial, antifungal, anti-malarial, antifeedant, molluscicidal, PTP1B inhibitory, and insect growth inhibitory activities. This review aims to provide an up-to-date literature survey and comprehensive insight into chemical structures, taxonomical distributions, and biological activities of the reported metabolites from the title genus whenever available.

The synchronization of complex networks is believed to be closely related to network topology. How to study synchronization of real network without clear topology and parameters? In this Letter, a synchronized stability boundary equation is derived that is system- and disturbance-independent and applicable to arbitrarily coupled grids. The results imply that spontaneous synchronization in a network may be network independent. These conclusions provide new research paths for network synchronization and analyze the synchronization stability of grids in a unified way.

Given the increased provision of international exchange programmes in higher education, this paper examines students’ perceptions of their learning process in one Erasmus+ programme in Food Innovation and Product Design. Using evaluation model of international exchange programme and triple helix model as the analytical framework, students’ testimonials from 2015–2021 were analysed using a critical discourse analysis. EU and non-EU students had similar perceptions of learning outcomes related to knowledge of the food innovation industry, but non-EU students had a stronger sense of awareness of both the international context and multicultural interaction.

Populations with essential hypertension have a high risk of nonalcoholic steatohepatitis (NASH). In this study, we investigated the mechanism that underlies the progression of hypertension-associated NASH by comparing differences in the development of high fat and cholesterol (HFC) diet-induced NASH among three strains of rats, i.e., two hypertensive strains comprising spontaneously hypertensive rats and the stroke-prone spontaneously hypertensive 5/Dmcr, and the original Wistar Kyoto rats as the normotensive control. We investigated histopathological changes and molecular signals related to inflammation in the liver after feeding with the HFC diet for 8 weeks. The diet induced severe lobular inflammation and fibrosis in the livers of the hypertensive rats, whereas it only caused mild steatohepatitis in the normotensive rats. Increased activation of proinflammatory signaling (transforming growth factor-β1/mitogen-activated protein kinases pathway) was observed in the hypertensive strains fed with the HFC diet. In addition, the HFC diet suppressed the nuclear factor erythroid 2-related factor 2 pathway in the hypertensive rats and led to lower increases in the hepatic expression of heme oxygenase-1, which has anti-oxidative and anti-inflammatory activities. In conclusion, these signaling pathways might play crucial roles in the development of hypertension-associated NASH.

Reciprocal Personal/Public Protection (RPPP) featured with source control is introduced, Mask Discriminating Mouth and Nose (MDMN) is employed to serve the purpose, which includes polymer based mouth cover with optional nose cover. The new knowledge that mouth is a primary, active and dominant source of the virus has been well established, which is the base of MDMN. Source classification and related source control tools are discussed, mouth cover is recommended as the tool prioritized to use. Liquid droplets is identified as a hard issue related to mask, liquid droplets, mask fitting, comfort and facial recognition constitute real challenges of mask in addition to efficiency, All of these have been addressed with MDMN. Comparisons between MDMN and masks/face covering are taken on four aspects: efficiency and efficacy, tolerance and comfort, cost and waste, and civil rights and public interest. Mouth cover is recommended to replace the face covering and act as both a personal tool and a public utensil, mouth cover with nose cover can provide better protection than N95 etc. RPPP with MDMN, could be an alternative for lockdown, a parallel strategy to vaccine, and a collectively living way during the pandemic era. MDMN, featured with high efficiency protection, high degree comfort, easy wearing, tight-fitting, easy facial recognition & communication, reusability, cost-effective, environment friendly and scale manufacturing more readily and widely etc., is a simple and sustainable solution, which is essential for ordinary people to keep wearing it properly for protection.

Although Darwin‘s evolutionary mutation theory has been widely accepted, many endeavors have been tried to challenge it. With more and more observation of successful hybridization and hybrids, the sexual isolation between species has become vague. The mechanism of evolution has been expanded from the classical model of evolution to multiple routes of speciation. Furthermore, a fundamental crossbreeding theory has been raised and proved by two lines of evidences: paleopolyploidy and fan-shaped spectrum of species. Ancient genome duplications are widespread throughout eukaryotic lineages, particularly in plants. The genome polyploidization, especially in the somatic cell hybridization, can break through the sexual incompatibility between diploid counterparts to hybridize and produce new species. By comparing characteristics, all species in every taxon, both in the extinct fossil and extant organisms, can be arranged into fan-shaped spectrum according to their similarity: left primitive type-middle advanced type-right primitive type. The species are primitive at the two ends and advanced at the middle. The primitive two species always resemble two types of more primitive species that can be confirmed as their ancestors respectively, and the middle species is half similar to the two ancestors respectively. These suggest that the species in the spectrum come from two different ancestors by crossbreeding and gene combination. As a sum, advanced species originated from crossbreeding of two primitive ancestors, by major method of polyploidization, and proved by results of fan-shaped spectrum of species. Then, sex is the cause, force and opportunity for evolution.

Shear dynamics simulation under extreme pressure was used to optimise the composition of ester-based lubricant base oil and extreme pressure additives. As a result, the ester-based lubricant in the weak-gel drilling fluid achieves reduction and increases the efficiency in drilling construction, and the field operation efficiency improves. The results of base oil lubrication simulation show that three base oils, namely, methyl oleate, ethyl oleate and butyl oleate, can be stably adsorbed on the surface layer of the shear surface. Methyl oleate has the lowest system temperature after shear stabilisation and has a high load-bearing capacity. The shear stress of methyl oleate decreases by changing the initial shear temperature and speed. It increases by 6.36 MPa when the speed increases from 10 m/s to 30 m/s. At this time, the shear stress of butyl oleate increases by 10.11 MPa. The results of the four-ball friction experiments show that the radius of the abrasion spot of methyl oleate is 179.83 μm, which is smaller than that of the other two base oils. Moreover, the friction coefficient of methyl oleate is 0.0018, which is approximately 1/3 of that of butyl oleate. Methyl oleate has better lubrication efficiency. The shear simulation results are consistent with the experimental results. The simulation can be used for the molecular design of lubricant materials. The oleic acid amide–containing amine group and the glyceride oleic–containing hydroxyl group were selected as the extreme pressure functional components for shear simulation. Results show that the shear stress of oleic acid amide is much lower than that of oleic acid glyceride when the initial shear temperature and speed change. The extreme pressure lubrication component–containing amine group is better than the extreme pressure lubrication material–containing hydroxyl group. The effects of different oleamide contents in the two-component mixtures on the lubricating properties were investigated through shear simulation, with methyl oleate as the base oil and oleamide as the extreme pressure functional component. The simulation results show that the lubricant has the optimal shear stress when 10% oleamide is added to the lubricant. The base properties of the lubricant were tested using a mixture of 90% methyl oleate and 10% oleamide, formulated as a lubricant. Results show that the friction coefficient can be reduced to 0.03 when 0.5% of the lubricant is added to the base mud. Moreover, the lubricant film formed shows high strength. Then, 1% lubricant was added to the weak-gel drilling fluid to evaluate the effect of the lubricant on the gel structure of the drilling fluid. Results show that adding lubricant does not affect the rheological properties of the drilling fluid. The gel structure of the system also remains stable even after 7 days of continuous ageing. The results of the field experiments in Hua3-01 well show that adding 1% ester-based lubricant to the field drilling fluid reduces the drilling friction by 33%. Thus, the efficiency of directional side drilling can be effectively improved, complicated accidents, such as poor starting and stopping of drilling and stuck jamming, can be avoided, and the goals of reducing quantity and increasing efficiency can be completed.

Saliency detection in synthetic aperture radar (SAR) image is a difficult problem. This paper proposed a multitask saliency detection (MSD) model for the saliency detection task of SAR image. Firstly, we extract four features of SAR image as the input of the MSD model, which include the intensity, orientation, uniqueness and global contrast. Then, the saliency map is generated by the multitask sparsity pursuit (MTSP) which integrates the multiple features collaboratively. Subjective and objective evaluation of the MSD model verifies its effectiveness. Based on the saliency maps of the source images, an image fusion method is proposed for the SAR and color optical image fusion. The experimental results of real data show the proposed image fusion method is superior to the presenting methods in terms of several universal quality evaluation indexes, as well as in the visual quality. The salient areas in the SAR image can be highlighted and the spatial and spectral details of color optical image can also be preserved in the fusion result.

Fire is a common natural disturbance in forest ecosystems and plays an important role in subsequent vegetation patterns. Based on the spatial sequence method instead of the time successional sequence method, this study selected burned areas in different locations in the Anning River Basin, which contains typical dry valleys. Quadrat surveys and quantitative classification were used to identify the vegetation classification, distribution pattern, and environmental interpretation during the natural restoration process after forest fire. The results showed that: (1) the vegetation community in the early stage of natural recovery after forest fire disturbance could be divided into seven community types, and Quercus guyavaefolia H. Leveille (Qg) was the dominant species in the community; (2) vegetation samples could be divided into five ecological types, and the classification and distribution pattern of community types in this region changed most obviously with altitude; and (3) detrended correspondence analysis could clearly classify vegetation community types, and detrended canonical correspondence analysis could well reveal the relationships between species and environmental factors. This study provides a scientific basis guiding the restoration of ecosystem structural stability and biodiversity in burned areas.

A space charge density wireless measurement system based on the idea of distributed measurement is proposed for collecting and monitoring the space charge density in an ultra-high-voltage direct-current (UHVDC) environment. The proposed system architecture is composed of a number of wireless nodes connected with space charge density sensors and a base station. The space charge density sensor based on atmospheric ion counter method is elaborated and developed, and the ARM microprocessor and Zigbee radio frequency module are applied. The wireless network communication quality and the relationship between energy consumption and transmission distance in the complicated electromagnetic environment is tested. Based on the experimental results, the proposed measurement system demonstrates that it can adapt to the complex electromagnetic environment under the UHVDC transmission lines and can accurately measure the space charge density.

The emergence of CDK4/6 inhibitors, such as palbociclib, ribociclib, and abemaciclib, has revolutionized the treatment landscape for hormone receptor-positive breast cancer. These agents have demonstrated significant clinical benefits in terms of both progression-free survival and overall survival. However, resistance to CDK4/6 inhibitors remains a challenge, limiting their long-term efficacy. Understanding the complex mechanisms driving resistance is crucial for the development of novel therapeutic strategies and improvement of patient outcomes. Translational research efforts, such as preclinical models and biomarker studies, offer valuable insight into resistance mechanisms and may guide the identification of novel combination therapies. This review paper aims to outline the reported mechanisms underlying CDK4/6 inhibitor resistance, drawing insights from both clinical data and translational research in order to help direct the future of treatment for hormone receptor positive metastatic breast cancer.

Photoacoustic imaging (PAI) is a cutting-edge biomedical imaging modality, providing detailed anatomical and functional information about the area beneath the skin surface. Its light energy deposition is such that PAI typically provides clear images of the skin with high signal-to-noise ratios. Specifically, the rich optical contrast of PAI allows biological information related to lesion growth, malignancy, treatment response, and prognosis to be seen. Given its significant advantages and emerging role in imaging skin lesions, we summarize and comment on representative studies of skin PAI, such as the guidance of skin cancer biopsies and surgical excisions, and the accurate diagnosis of psoriasis. We conclude with our insights about the clinical significance of skin PAI, showing how its use to identify biological characteristics in lesion microenvironments allows early diagnosis and prognosis of disease.

Excretory-secretory products (ESPs) are the main research targets for investigating the hosts and helminths interaction. Parasitic worms can migrate to parasitic sites and avoid the host immune response by secreting this product. Angiostrongylus cantonensisis an important food-borne zoonotic parasite that causes severe neuropathological damage and symptoms, including eosinophilic meningitis or meningoencephalitis in humans. Benzaldehydes are organic compounds composed of a benzene ring and formyl substituents. This compound has anti-inflammatory and antioxidation properties. Previous studies showed that 3-hydroxybenzaldehyde (3-HBA) and 4-hydroxybenzaldehyde (4-HBA) can reduce apoptosis in A. cantonensis ESPs treated astrocytes. These results on the protective effect underlying benzaldehyde have primarily focused on cell survival. The study was designed to investigate the molecular mechanisms of endoplasmic reticulum stress (ER stress) and oxidative stress in astrocytes in A. cantonensis ESPs treated astrocytes and to evaluate the therapeutic consequent of 3-HBA and 4-HBA. First, we initially established the RNA-seq dataset in each group, including Normal, ESPs, ESPs+3-HBA, and ESPs+4-HBA. We also found that benzaldehyde (3-HBA and 4-HBA) can stimulate astrocytes to express ER stress-related molecules after ESP treatment. The level of oxidative stress could also be decreased in astrocytes by elevating antioxidant activity and reducing ROS generation. These results suggested that benzaldehyde may be a potential therapeutic compound for human angiostrongyliasis to support brain cell survival by inducing the expression levels of ER stress- and oxidative stress-related pathway.

It is known that the class of p-normed spaces (0 < p ≤ 1) is an important generalization of usual normed spaces with rich topological and geometrical structure, but the most of tools and general principles in nature with nonlinearity have not been developed yet, thus the main goal of this paper is to develop tools for nonlinear analysis under the framework of p-vector spaces. In particular, we first develop the general fixed point theorems which provide solutions to answer Schauder conjecture since 1930’s in the affirmative for p-vector spaces when p = 1 (which is just general topological vector spaces); then the one best approximation result for upper semi-continuous mappings is given, which is used as a powerful tool to establish fixed points for non-self set-valued mappings with either inward or outward set conditions; and finally we establish comprehensive existence results of solutions for Birkhoff-Kellogg Problems, and the general principle of nonlinear alternative by including Leray-Schauder alternative and related results. The results given in this paper not only include the corresponding results in the existing literature as special cases, but also expected to be useful tools for the study of nonlinear problems arising from theory to practice.

Abstract: Steamed ginseng water (SGW), the by-product generated from the heated processing of red ginseng, with high content of active substances, better skincare activities, and large amount output ineffective utilization, resulted in environmental pollution and resource waste. In current study, UHPLC-Q-Exactive-MS/MS liquid chromatography-mass spectrometry and multivariate statistical analysis were conducted to characterize the compositional features of the repeated thermal-treated SGW. The total sugar content, total sugar content, total reducing sugar content, total non-reducing sugar content, DPPH, ABTS+, Fe3+ reducing capacity, and the hydroxyl radical scavenging abilities were employed to evaluate the gross contents variation connect with anti-oxidant activities during heat processes. The result revealed the SGW content and antioxidant activity were highly correlated, the 7th SGW sample showed the highest content and the strongest ability on anti-aging capacities. 38 significant common differential markers were screened, by the four compared SGW groups (1- and 3-, 1- and 5-, 1- and 7-, and 1- and 9) through OPLS-DA analysis. The current study showed that the thermal proceeding times could be a vital index value during the recycling operation quality control of SGW, which has a huge potential in anti-aging cosmetic raw materials, In the meanwhile, our results provided a green, sustainable, low-cost thinking of rational application on ginseng resource.

As the global population rapidly ages with longer life expectancy and declining birth rates, the need for healthcare services and caregivers for older adults is increasing. Current research envisions addressing this shortage by introducing domestic service robots to assist with daily activities. The successful integration of robots as domestic service providers in our lives requires them to possess efficient manipulation capabilities, provide effective physical assistance, and have adaptive control frameworks that enable them to develop social understanding during human-robot interaction. In this context, human factors, especially quantifiable ones, represent a necessary component. The objective of this paper is to conduct an unbiased review encompassing studies on human factors studied in research involving physical interactions and strong manipulation capabilities. We identified the prevalent human factors in physical human-robot interaction (pHRI), noted the factors typically addressed together and determined the frequently utilized assessment approaches. Additionally, we gathered and categorized proposed quantification approaches based on measurable data for each human factor. We also formed a map of common contexts and applications addressed in pHRI for a comprehensive understanding and easier navigation of the field. We found out that most of the studies in direct pHRI (when there is direct physical contact) focus on social behaviors with belief being the most commonly addressed human factor type. Task collaboration is moderately investigated, while physical assistance is rarely studied. In contrast, indirect pHRI (when the physical contact is mediated via a third item) studies often involve industrial settings, with physical ergonomics being the most frequently investigated human factor. More research is needed on human factors in direct and indirect physical assistance applications, including studies that combine physical social behaviors with physical assistance tasks. We also found that while the predominant approach in most studies involves the use of questionnaires as the main method of quantification, there is a recent trend that seeks to address quantification approaches based on measurable data.

In this paper, a new approach is proposed for designing ultra-low-power FFT (Fast Fourier Transform) system suitable for use in energy harvesting powered sensors. Bit-serial architecture is adopted to reduce the power consumption of butterfly operation. Simulation results show that, compared with state-of-the-art bit-serial and conventional parallel processors, the proposed technique is superior in terms of silicon area, power consumption, dynamic energy use due to variable precision arithmetic. A sample design of a 64-point FFT shows that the implementation can save about 40% area and 36% leakage power compared with a conventional parallel counterpart, accordingly achieving significant power benefits at a low sample rate and low voltage domain. The dynamic variation of the arithmetic precision can be achieved through a simple modification of the controller with hardware area overhead of 10% gate count.

China is in the climbing phase of the "Inverted U" environmental Kuznets curve, from excessive environmental consumption to the development stage of governance and protection, and green innovation. It is the most complex period of environmental quality. Environmental and policy regulation are very important. Select panel data of 29 provinces of China (excluding Hong Kong, Macau, Taiwan, Hainan and Tibet) from 2008 to 2017, construct a nonlinear two-threshold regression model, empirically analyse the impact of environmental tax and government innovation subsidies to green processes innovation, and attempt to explore whether the implementation of these two policies at the same time can make enterprises more inclined to green process innovation and whether there is an optimal space for policy implementation. It is proposed that the synergy effect of environmental tax and government innovation subsidy policies on enterprise green process innovation should be fully utilized, and the enterprise green process innovation environment and incentive mechanism should be improved to promote the green transformation and sustainable development of enterprises.

The mammalian or mechanistic target of rapamycin (mTOR) integrates multiple intracellular and extra-cellular upstream signals involved in the regulation of anabolic and catabolic processes in cells, and plays a key regulatory role in cell growth and metabolism. Activation of the mTOR signaling pathway has been reported to be associated with a wide range of human diseases. A growing number of in vivo and in vitro studies have demonstrated that the gut microbes and its complex metabolites can regulate host metabolic and immune responses through the mTOR pathway, and result in disorders of host phys-iological functions. In this review, we summarize the regulatory mechanisms of gut microbes and mTOR in different diseases, and discuss the crosstalk between gut microbes and their metabolites and mTOR in the disorders in gastrointestinal tract, liver, heart and other organs. We also discuss the promising appli-cation of multiple potential drugs that can adjust the gut microbiota and mTOR signal pathways. Despite the limited findings between gut microbes and mTOR, elucidating their relationship may provide new clues for the prevention and treatment of various diseases.

Cellular senescence has recently been recognized as a hallmark of cancer, reflecting its association with aging and inflammation, its role as a response to deregulated proliferation and oncogenic stress, and its induction by cancer therapies such as radiation, chemotherapy, and targeted agents. While such therapy-induced senescence (TIS) has been linked to resistance, recurrence, metastasis and normal tissue toxicity, TIS has the potential to enhance therapy response and stimulate anti-tumor immunity. In this review, we examine the Jekyll and Hyde nature of senescent cells (SnCs), with a particular focus on how their persistence while expressing the senescence-associated secretory phenotype (SASP) modulates the tumor microenvironment through autocrine and paracrine mechanisms. Via the SASP, the formation of SnCs may alternately mediate resistance or response to conventional therapy. Further, toward fulfilling the unmet potential of cancer immunotherapy, we consider how SnCs may influence tumor inflammation and serve as a source of antigen to potentiate anti-tumor immunity. This new view suggests treatment strategies based on inducing TIS to enhance immune checkpoint blockade. Finally, we describe strategies for mitigating the detrimental effects of senescence, such as modulating the SASP or targeting SnC persistence, toward enhancing the benefits of cancer treatment.

In recent years, there has been significant growth in the ubiquity and popularity of three dimensional(3D) point clouds, with an increasing focus on the classification of 3D point clouds. To extract richer features from point clouds, many researchers have turned their attention to various point set regions and channels within irregular point clouds. However, this approach has limited capability in attending to crucial regions of interest in 3D point clouds and may overlook valuable information from neighboring features during feature aggregation. Therefore, this paper proposes a novel 3D point cloud classification method based on global attention and adaptive graph convolution. The method consists of two main branches: the first branch com-putes attention masks for each point, while the second branch employs adaptive graph convolu-tion to extract global features from the point set. It dynamically learns features based on point interactions, generating adaptive kernels to effectively and precisely capture diverse relationships among points from different semantic parts. Experimental results demonstrate that the proposed model achieves 93.8% in overall accuracy and 90.8% in average accuracy on the ModeNet40 dataset.

In this paper, we study the well-posedness and asymptotic behaviour of solutions to a laminated beam in thermoelasticity of type III. We first give the well-posedness of the system by using the semigroup method. Then, we show that the system is exponentially stable under the assumption of equal wave speeds. Furthermore, it is proved that the system is lack of exponential stability for case of nonequal wave speeds. In this regard, a polynomial stability result is proved.

This study utilises NaOH to treat composite cementitious materials containing aeolian sand and zeolite powders, which were used to replace 50% of the cement in aeolian-sand concrete (ASC). The mechanical properties of treated ASC considerably improved, especially when the NaOH dosage was 4% by mass. After curing this sample (denoted as AAZC-4) for 28 d, its compressive strength improved by 17.2% and its split tensile was increased by 16.3%. Potassium feldspar and montmorillonite in zeolite powder and SiO2 in the sand were decomposed by OH− and combined with other elements to generate various silicate gels and A-type potassium zeolite crystals inside the concrete. Microscopic examination showed that the gels and crystals intertwined to fill the pores, decreasing (increasing) the percentage of large (small) pores, thus optimising the pore structure. This substantially improved the mechanical properties of ASC. Freeze–thaw salt-intrusion tests showed that the extent of mass loss, degree of damage and loss of compressive strength of AAZC-4 were similar to those of ordinary concrete but were reduced by 36.8%, 19% and 52.1%, respectively, compared with those of ASC. Therefore, AAZC-4 has sustainable working performance in the chloride ion permeable environment in cold and arid areas.

Currently, efficient utilization of low-grade thermal energy is a great challenge. Thermoelectricity is an extremely promising method of generating electrical energy from temperature differences. As a promising energy conversion technology, thermo-electrochemical cells (TECs) have attracted much attention in recent years for their ability to convert thermal energy directly into electricity with high thermal power. Within TECs, anions and cations gain and lose electrons, respectively at the electrodes using the potential difference between the hot and cold terminals of the electrodes by redox couples. Additionally, the anions and cations therein are constantly circulating and mobile via concentration diffusion and thermal diffusion, providing an uninterrupted supply of power to the exterior. This review article focuses mainly on the operation of TECs, recent ad-vances in redox couples, electrolytes, and electrodes. The outlook for optimization strategies re-garding TECs is also presented in this paper.

The exploration and identification of targets and pathways for Atopic dermatitis (AD) treatment and diagnosis are critical for AD control. The conventional target exploration approach such as the literature review is not satisfying in terms of efficiency and accuracy. Recently, the bioinformatic approach is drawing attention for its unique advantage of high-volume data analysis for target and pathway exploration; Open Targets Platform is the targets source for this study to extract top 200 high-rank proteins from 3122 AD associated proteins. STRING, Cytoscape, CytoHubba, ClueGo, and CluePedia function had been applied for data analysis. The KEGG Mapper search & colour pathway was the pathway map resource for identified pathways; 23 key hub genes (VDR, KIT, BCL2L11, NFKBIA, KRAS, IL13, JAK2, STAT3, IL21, IL4R, REL, PDGFRB, FOXP3, RARA, RELB, EGFR, IL21R, MYC, CREBBP, NR3C1, IL2, JAK1, and KITLG). Additionally, 8 correlated pathways and the biological process had been identified; Through this study, a viable approach for target and pathway exploration had been presented. The identified AD targets and pathways will be tested for upcoming research for traditional Chinese medicinal herb interactions

As a manifestation of technological innovation achievements, patents reflect the frontier of technological development in the field. This paper constructs a multi-entity patent collaboration network and analyzes its evolution patterns to provide a reference for innovation organizations to grasp the general direction of innovation development and select partners. Based on the data of collaboration patents of two and three organizations in China's new energy vehicles (NEV) industry from 2008 to 2021, this paper constructs higher-order interaction collaboration innovation networks in different periods to analyze the spatial evolution of networks and patent cooperation activities. The results show that the generalized degree distribution of nodes and edges conforms to the power-law distribution. The two-dimensional simplex networks gradually form triangle groups centered on the core nodes, and the importance of key edges is beginning to emerge. Key organizations and partners, including State Grid Corporation of China, Tsinghua University, and China Electric Power Research Institute, will largely determine the direction for the future development of cooperation innovation. The study also reveals that Beijing, Jiangsu, Zhejiang, Guangzhou, and Shanghai are in central positions in the cooperative innovation network, based on their cooperation breadth and depth measures. Additionally, key links formed by Beijing as hubs are not only the center of information exchange but also function as bridges that connect to other regions.

The data assimilation method to improve sea fog forecast over the Yellow Sea is usually three-dimensional variational assimilation (3DVAR), whereas ensemble Kalman filter (EnKF) has not yet been applied on this weather phenomenon. In this paper, two sea fog cases over the Yellow sea, one spread widely and the other spread narrowly along the coastal area, are studied in detail by a series of numerical experiments with 3DVAR and EnKF based on the Grid-point Statistical Interpolation (GSI) system and the Weather Research and Forecasting (WRF) model. The results show that the assimilation effect of EnKF outperforms that of 3DVAR: for the widespread-fog case, the probability of detection and equitable threat scores of the forecasted sea fog area get improved respectively by ~57.9% and ~55.5%; the sea fog of the other case completely mis-forecasted by 3DVAR is produced successfully by EnKF. These improvements of EnKF relative to 3DVAR are benefited from its flow-dependent background error, resulting in more realistic depiction of sea surface wind for the widespread-fog case and better moisture distribution for the other case in the initial conditions. More importantly, the correlation between temperature and humidity in the background error of EnKF plays a vital role in the response of moisture to the assimilation of temperature, which leads to a great improvement on the initial moisture conditions for sea fog forecast.

The surface velocity of the Amery Ice Shelf (AIS) is vital to assessing its stability and mass balance. Previous studies have shown that the AIS basin has a stable multi-year average surface velocity. However, spatiotemporal variations in the surface velocity of the AIS and the underlying physical mechanism remain poorly understood. This study combined offset tracking and DInSAR methods to extract the monthly average surface velocity of the AIS and obtained the inter-annual surface velocity from the ITS_LIVE product. An uneven spatial distribution in inter-annual variation of the surface velocity was observed between 2000–2022, although the magnitude of variation was small at less than 20.5 m/yr. The increase and decrease in surface velocity on the eastern and western-central sides of the AIS, respectively, could be attributed to the change in the thickness of the AIS. There was clear seasonal variation in monthly average surface velocity at the eastern side of the AIS between 2017–2021, which could be attributed to variations in the area and thickness of fast-ice and also to variations in ocean temperature. This study suggested that changes in fast-ice and ocean temperature are the main factors driving spatiotemporal variation in the surface velocity of the AIS.

Orogenic antimony-gold deposits contribute significantly to the global antimony resource base. China's orogenic antimony-gold deposits are primarily in southern Tibet. Investigations indicate that antimony combines and migrates with sulfur hydroxides in ore-forming fluids. Previous research on fluid inclusions in orogenic antimony-gold ores with sedimentary rock accommodation revealed the presence of organic inclusions, including liquid hydrocarbons, alongside common components such as CO2, H2O, CH4, and NaCl. However, the impact of liquid hydrocarbons on antimony migration and mineralization is still de-batable. To investigate the transportability of antimony by liquid hydrocarbons in orogenic antimony ores, we selected n-dodecanethiol and n-dodecane as the subjects. We measured the solubility and occurrence form of antimony in these compounds at various temperatures and durations. The results indicate that after 5 and 10 days of reaction at 100 °C, the antimony concentrations in the n-dodecanethiol and n-dodecane groups were 67.44±7.62 ppm, 75.15±16.74 ppm, 1.40±1.02 ppm, and 3.02±3.09 ppm, respectively. At 150 °C for 5 and 10 days, the respective concentrations were 50.58±5.39 ppm, 77.26±45.20 ppm, 2.66±3.08 ppm, and 2.41±2.03 ppm. At 200 °C for 5 and 10 days, the corresponding concentrations were 339.76±71.94 ppm, 218.97±25.03 ppm and 6.53±7.17 ppm, 2.27±0.82 ppm (n=3). The measured solubility of antimony in the n-dodecanethiol group increased gradually with rising temperature. The solubility of antimony in the n-dodecane group was low and notably inferior to that observed in the n-dodecanethiol group. X-ray photoelectron spectroscopy (XPS) analysis demonstrated a distinct thiol (R-SH) peak at 163.31 eV and compound peaks of antimony reacting with thiols at 162.06 and 160.87 eV. This suggests that antimony predominantly forms complexes with thiols for migration. Our findings suggest that specific liquid hy-drocarbon components, predominantly thiols, can interact with antimony at metallogenic temperatures and persist in ore-forming fluids, facilitating migration and mineral enrichment. Earlier experimental studies on gold and crude oil have indicated that liquid hydrocarbons also play an essential role in the transportation and enrichment of gold during the formation of gold deposits, thus indicating that liquid hydrocarbons possess the considerable potential to act as an ore-forming fluid during orogenic antimony-gold deposit formation in southern Tibet.

Bipedal locomotion remains one of the major open challenges of humanoid robotics. The common approaches are based on simple reduced model dynamics to generate walking trajectories, often neglecting the whole-body dynamics of the robots. As motions in nature are often considered as optimal with respect to certain criteria, in this work we present an optimal control based approach that allows us to generate optimized walking motions using a precise whole-body dynamic model of the robot, in contrast with the common approaches. The optimal control problem is formulated to minimize a set of desired objective functions with respect to physical constraints of the robot and contact constraints of the walking phases. We apply the method with combinations of different objective criteria to the model of a reduced version of the iCub humanoid robot of 15 internal DOF. The obtained trajectories are executed on the real robot and we carry out a discussion on the differences between the outcomes of this approach with the classic approaches.

The merge areas of freeway work zones include relatively significant safety hazards that have continuously led to urgent safety issues to be solved by the management departments. In order to make up for the cumbersome process of independent identification of rear-end collision and lane change collision on complex road sections, an appropriate identification method of traffic conflicts in the merge area of freeway work zone was explored, this study collected vehicle running tracking data from the merge areas of multiple work zones, using an unmanned aerial vehicle video technique. Based on an inter-frame difference method and the principle of a spatio-temporal context visual tracking algorithm, the vehicles were detected and tracked, and the coordinate data of the vehicles in continuous motion were parsed using MATLAB extension tools. Based on the behavior characteristics of vehicle conflict avoidance, a new identification method for evading severe traffic conflicts is proposed according to the initial velocity, acceleration and accident rate of section traffic. Then, a statistical analysis was performed on the spatial distribution characteristics of the traffic conflicts in typical merge areas. The impacts of the road conditions in work zones, vehicle factors, and traffic flow factors on the traffic conflicts were analyzed. A binomial logistic model was established to identify the main influencing factors. The results show that in the merge area of the freeway work zone, there are serious traffic conflicts between vehicles in the following two situations: (Ⅰ) v∈[7,13.5] m/s and a∈[-3.96,-0.65]m/s2; and (Ⅱ) v∈[13.5,24.3] m/s, and a∈[-3.96,-1.57] m/s2. The probabilities of serious traffic conflicts in the first and last 25 m of the merge area are greater than those in the other sections. The smaller the space between the upstream work zone and the merge area, the greater the probability of serious traffic conflicts between vehicles. When the average vehicle speed is relatively high, the probability of serious conflicts is the highest, i.e., by a multiple of 5.95 from the baseline. Moreover, the probability of serious conflicts between vehicles is higher for larger vehicles, i.e., 4.765 times that for small vehicles. The research results can serve as a reference for freeway management departments to improve the safety levels of merge areas during road work. For example, the probability of serious conflicts can be effectively reduced by setting up reasonable speed limit signs in the work zone, increasing the spacing between work zone and merge area, and appropriately diverting large vehicles.

In order to meet the military requirements of the fuze, such as precision strike, efficient mutilates ability and low collateral damages, the microminiaturization is an inevitable trend of secure system. Based on the silicon-based MEMS S&A device designed by our term, the design principles of each module and fabrication process are introduced. The average fracture strength and Young's modulus of the silicon are 726 MPa and 175 GPa from the tensile test, respectively. From Hopkinson impact experiment, we can get the threshold-value judging mechanism being safety under the impact overload of 20526 g, and this value is much more than the standard of the drop overload 12000g; the arming value under the centrifugal overload obtained from theory, simulation and experiment is at the range of 28200 g and 32000 g, it shows that the threshold-value judging mechanism can be arming compared with the value 35951g of design principle. Therefore, the threshold-value judging mechanism can meet the design requirements of overload. Furthermore, the relationship of fracture threshold-values obtained by different theories is found out through parametric design method, as shown in Figure 14, it provides the theory evidence to the follow parametric design.

The Doppler band compensated by the keystone transform (KT) is limited. Therefore, it needs to be used in conjunction with the Doppler ambiguity compensation function to correct the range migration (RM) caused by maneuvering targets with Doppler ambiguity. However, the KT implemented by sinc interpolation suffers from significant performance loss at boundaries of compensation Doppler bands. Additionally, in a multi-target scenario, KT implementation methods occupy high complexity when the Doppler range of targets spans over two compensation Doppler bands. To address aforementioned issues, this study presents a variable Doppler starting point keystone transform (VDSPKT) method, where a new form of ambiguity compensation function is constructed, turning the Doppler starting point of the compensation band in KT variable. Firstly, the position of the compensation Doppler band is changed from fixed to adjustable as needed, enhancing the flexibility of KT. Crucially, the connection points of the compensation Doppler bands in sinc interpolation are reset, avoiding the performance loss at their boundaries. Also, the compensation band is adjusted to cover the narrow Doppler frequency range caused by targets, significantly improving the computational efficiency. Finally, the simulation results demonstrate that the proposed approach effectively addresses the performance degradation and high computational complexity of KT in the aforementioned scenarios, resulting in a computational load reduced by approximately 50% compared to traditional methods.

In order to foster a more sustainable and eco-friendly trajectory for the construction industry, while concurrently mitigating environmental pollution and energy inefficiency, it is imperative to cultivate an environmentally conscious building and urban environment. Under the background of carbon peak and carbon neutrality, green building evaluation system (GBRS) has become a research hotspot in the field of green building. This paper systematically summarizes the current research progress based on GBRS, focuses on the current weight and indicators setting, analyzes it with Cite Space software, and puts forward its future development direction. The results show that the weight setting method of green building evaluation system is determined by multidimensional and multi-method. From the perspective of environment, society and economy, the scope of indicators setting is expanding. The green building evaluation system will play a guiding role in green building design, and the evaluation process will continue to be optimized and developed in the direction of intelligence and automation.

Extensive genome structure variation, such as copy number variations (CNVs) and presence/absence variations, is the basis for the remarkable maize genetic diversity; however, the effect of CNVs on maize herbivory defense remains largely underexplored. Here, we report that the naturally occurring duplication of the maize 9-lipoxygenase gene, ZmLOX5, leads to increased resistance of maize to herbivory by fall armyworms (FAW). Previously, we showed that ZmLOX5-derived oxylipins are required for defense against chewing insect herbivores and identified several inbred lines, including Yu796, that contained duplicated CNVs of ZmLOX5, referred to as Yu796-2×LOX5. To test whether introgression of the Yu796-2×LOX5 locus into the herbivore-susceptible B73 background that contains a single ZmLOX5 gene is a feasible approach to increase resistance, we generated a series of near-isogenic lines that contained either 2, 1 or 0 copies of the Yu796-2×LOX5 locus in the B73 background by six back crosses (BC6). Droplet digital PCR (ddPCR) confirmed the successful introgression of the Yu796-2×LOX5 locus in B73. The resulting B73-2×LOX5 inbred line displayed increased resistance against FAW associated with increased expression of ZmLOX5, increased wound-induced production of its primary oxylipin product, the α-ketol, 9-hydroxy-10-oxo-12(Z),15(Z)-octadecadienoic acid (9,10-KODA), and the downstream defense hormones regulated by this molecule, 12-oxo-phytodienoic acid (12-OPDA) and abscisic acid (ABA). Surprisingly, wound-induced JA-Ile production was not increased in B73-2×LOX5, resulting from the increased JA catabolism. Furthermore, B73-2×LOX5 displayed enhanced drought tolerance likely due to increased ABA and 12-OPDA content. Taken together, this study revealed that the duplicated CNV of ZmLOX5 quantitively contributes to maize antiherbivore defense and presents proof-of-concept evidence that the introgression of naturally occurring duplicated CNVs of a defensive gene into the productive, but susceptible, crop varieties is a feasible breeding approach for enhancing plant resistance to herbivory and tolerance to abiotic stress.

Drugs-drugs interactions(DDI) are entities composed of different chemical substructures (functional groups). In existing methods that predict drug–drug interactions based on the usage of substructures, each node is considered the center of a substructure, and adjacent nodes eventually become centers of similar substructures, resulting in redundancy. Furthermore, the significant differ- ences in structure and properties among compounds can lead to unrelated pairings, making it difficult to integrate information. This heterogeneity negatively affects the prediction results. To address these issues, we propose a drug–drug interaction prediction method based on substructure signature learning (DDI-SSL). This method extracts useful information from local subgraphs surrounding drugs and effectively utilizes substructures to assist in predicting drug side effects. Additionally, a deep clustering algorithm is used to aggregate similar substructures, allowing any individual subgraph to be reconstructed using this set of global signatures. Furthermore, we developed a layer-independent collaborative attention mechanism to model the mutual influence between drugs, generating signal strength scores for each class of drugs to mitigate noise caused by heterogeneity. Finally, we evaluated DDI-SSL on a comprehensive dataset and demonstrated improved performance in DDI prediction compared to state-of-the-art methods.

This study examines the Health Silk Road (HSR) as a critical component of China's Belt and Road Initiative (BRI) and its implications for global health and international relations. The HSR aims to enhance public health and foster international cooperation in the healthcare sector, with objectives including strengthening healthcare infrastructure, expanding China's global health leadership, and enhancing international health cooperation. Through an in-depth analysis of the China-Pakistan collaboration on healthcare under the China-Pakistan Economic Corridor (CPEC) as a case study, this research explores the motives, implications, and potential concerns associated with the HSR. This research posits that the HSR has a mix of positive and negative implications, making it challenging to categorize the initiative as simply good or bad. While the HSR contributes to improved healthcare services, infrastructure, and capacity-building in participating countries, it also raises concerns about debt sustainability, transparency, and China's geopolitical influence. This research contributes to a nuanced understanding of the HSR's multifaceted impacts and underscores the importance of open dialogue, cooperation, and the sharing of best practices among stakeholders in order to maximize the initiative's benefits and minimize potential negative consequences. By assessing the motives, implications, and concerns of the HSR, this study offers valuable insights for policymakers, global health practitioners, and scholars, highlighting the significance of international collaboration in addressing shared health challenges and promoting sustainable development.

A revised reversed Carnot cycle without external heat source and temperature gap is proposed to challenge the classic reversed Carnot cycle, heat pumps based on the proposed cycle with super energy efficiency works just like electric heater fitted for any climate including extreme cold weather, the application of these new heat pumps is discussed with conclusion that little real obstacles exist for scale application to address the heating related climate change, also a demonstration case shows a remarkable results to encourage the applications of these new heat pumps.

Ultralight power generation equipment has high requirements for the power density, continuous operation, and transient stability of the whole machine, and there is a direct conflict between high power density design and substantial stability control in the power unit design. In order to meet the power density requirements of ultra-light power stations, three main problems need to be solved, namely engine speed oscillation and flameout in the process of load power mutation, matching of the generator and engine torque, and stabilizing the voltage waveform of the AC output end. In this paper, we proposed an exquisite control strategy for ultralight power generation systems in engines, generators, and inverters. The effectiveness and practicability of the proposed strategy are verified by both simulation and experiment. The results show that the proposed control strategy can effectively solve the instability problem of the ultralights generator set and improve the stability of the system, where the response recovery can be achieved within 0.9 seconds under the condition of total load increase or decrease, and the mismatching degree of the generator following the engine is reduced by 90%. The strategy could also guarantee long-term stable operation with high-quality electrical energy output.

Complexity science studies physical phenomena that cannot be explained by the mere analysis of the single units of a system but requires to account for their interactions. A feature of complexity in connected systems is the emergence of mesoscale patterns in a geometric space, such as groupings in bird flocks. These patterns are formed by groups of points that tend to separate from each other, creating mesoscale structures. When multidimensional data or complex networks are embedded in a geometric space, some mesoscale patterns can appear respectively as clusters or communities, and their geometric separability is a feature according to which the performance of an algorithm for network embedding can be evaluated. Here, we introduce a framework for the definition and measure of the geometric separability (linear and nonlinear) of mesoscale patterns by solving the travelling salesman problem (TSP), and we offer experimental evidence on embedding and visualization of multidimensional data or complex networks, which are generated artificially or are derived from real complex systems. For the first time in literature the TSP’s solution is used to define a criterion of nonlinear separability of points in a geometric space, hence redefining the separability problem in terms of the travelling salesman problem is an innovation which impacts both computer science and complexity theory.

This paper uses the complex regression analysis method to establish the customer’s load regression models, which consider economic indicators, temperature and rainfall. Furthermore, the proposed models are used to study the forecasting feasibility of the future energy sales and summer peak load demand. At first, this paper used least-squares techniques to derive regression models for considering economic indicators and temperature of 34 customer energy sales and total energy sales. Besides, the AMI high voltage customer demand data and system generating capacity for 24 hours were adopted to forecast summer peak load. The above-mentioned data analysis tool is used by EViews software to achieve, in order to verify the feasibility of the research framework. The study found that although its forecasting model accuracy is low only when mixed with temperature and high voltage demands. So, when mixed with high voltage demand data and system generating capacity for 24 hours to forecast peak load, the average error is ± 0.87% and in the majority of its energy sales forecasting model of average error is ±3%. This result can provide power company as future reference.

Under the development mode of deep blending of emerging technologies, major projects are important for enhancing China's comprehensive national strength and independent innovation capability. Based on the social benefits of major projects, and considering the influence of reputation factors, an evolutionary game model composed of a general contractor and subcontractor of major projects is established. This paper studies the influence of various factors including the income distribution coefficient of collaborative innovation, and MATLAB simulation software is analyzed the influence of factors on an evolutionary path. The results show that a reasonable income distribution coefficient can promote the game behavior of both parties to the direction of active collaborative innovation; The reduction of innovation cost and the improvement of spillover technology absorption capacity can make innovation subjects tend to choose active collaborative innovation strategies. In addition, reputation loss above a specific threshold can effectively inhibit free-riding behavior and encourage innovation subjects to choose active collaborative innovation strategies. The research results provide reference for promoting major projects' technology innovation.

Plant-microbe interactions are essential for ecosystem health and agricultural productivity. Metabolomics has revolutionized our understanding of these interactions by providing powerful methods to decipher the complex chemical signals involved. This review highlights the various metabolomics techniques used to study plant-microbe interactions, such as mass spectrometry, nuclear magnetic resonance spectroscopy, and advanced imaging technologies. We also discuss the role of contemporary bioinformatics tools, extensive databases, and the increasing influence of artificial intelligence and machine learning in the analysis of metabolomics data. Integrating metabolomics with other omics fields, including transcriptomics, proteomics, and metagenomics, allows for a comprehensive understanding of the molecular mechanisms underlying plant-microbe interactions. The review emphasizes the significance of fluxomics in elucidating the dynamic nature of metabolic networks. While there are challenges in data analysis, integration, and interpretation, metabolomics has profoundly expanded our knowledge of the role metabolites play in shaping plant-microbe interactions. As metabolomics technologies advance and integrate further with other omics approaches, we anticipate groundbreaking discoveries that will provide deeper insights into these complex interactions, ultimately leading to innovative strategies for sustainable agriculture and biotechnology.

Perinatal brain injury is a major public health problem burdened with high morbidity, mortality and severe neurological sequelae. Despite advances in neonatal life-saving technologies, neonatal encephalopathy lacks specific and effective treatment. Therefore, mechanisms of central nervous system changes associated with perinatal brain injury have been a hot topic of neonatology research. In recent years, researchers have shifted more focus from neurons themselves to perineuronal cells and intercellular interactions. As a member of the nervous system network, astrocytes are one of the dominant glial cells that regulate ion homeostasis, blood flow, and antioxidant function in the brain. Their changes in molecular mechanisms (e.g., alterations in RNA regulatory networks) during brain injury storms deserve further attention. Non-coding RNAs participate in and promote reactive pathophysiologic changes in astrocytes. The review summarizes and discusses the role of non-coding RNAs in astrocytes in recent years in studies of neonatal brain injury. It focuses on the most studied disease-related ncRNAs: miRNAs, lncRNAs and circRNAs, and hopes to provide possible directions for pathophysiological studies and therapeutic approaches of neonatal brain injury.

With the advancement of the economy and society, policymakers acknowledge the significance of improving rural households' well-being as a crucial factor in promoting sustainable economic and social development. Based on the matching data of China Household Finance Survey and Digital Rural County Index, this study empirically examines the effect and mechanisms of digital village construction on subjective well-being of rural households. The results revealed that digital village construction has a significant improvement in their subjective well-being. The impact of digital village construction is particularly significant in rural areas located in the western regions of China, as well as among households possessing higher levels of human capital. The process through which digital village construction enhances the subjective well-being of rural households involves the augmentation of household income, the promotion of non-farm employment opportunities, and the enhancement of rural governance. This study provides robust micro-empirical evidence highlighting the positive welfare effects of digital rural construction. This study provides insights into the digital village construction within the happiness economy framework, offering a new perspective. The imperative to strengthen rural digital infrastructure and improve farmers' proficiency in modern information skills is a strategic policy aimed at enhancing well-being of rural households.

The COVID-19 pandemic caused by SARS-CoV-2 poses a devastating threat to human society in terms of health, economy and lifestyle. Establishing accurate and real-time models to predict and assess the impact of the epidemic on the economy is instructive. We have designed a new model to quantitatively assess the impact of the COVID-19 on the economy of China’s mainland. The nominal GDP in the Q1 of 2020 that we predicted for China’s mainland with the Baidu Mi-gration Data is RMB 20,785.7 billion, which is less by 3.59% than that in 2019. The estimated val-ue is confirmed roughly by the official report released in April 17, 2020 (RMB 20,650 billion, 6.8% year-on-year declined). Strict control measures during the epidemic have greatly reduced Chi-na's economic activity and had a serious impact on the country's economy. Orderly promotion of population mobility plays a decisive role in economic recovery.

Modern war is sudden and rapid, and once the battle starts, the demand for equipment maintenance and guarantee will show an outburst situation, which puts equipment maintenance and guarantee capability to a severe test. To accurately grasp the civil-military integration of aviation maintenance and guarantee capabilities, it is necessary to evaluate their capabilities. To this end, the evaluation indicator system is established by using the three-dimensional indicator system construction model of "maintenance task → task demand → capability demand", and the evaluation method based on intuitionistic fuzzy entropy and normal grey cloud model is proposed, using intuitionistic fuzzy entropy theory to determine the expert weights and indicator weights, and the grey cloud model theory to determine the capability evaluation level. Finally, the application process of the evaluation model is demonstrated through specific examples, and the evaluation results are analyzed to verify the effectiveness of the evaluation model.

Modern war is sudden and rapid, and once the battle starts, the demand for equipment maintenance and guarantee will show an outburst situation, which puts equipment maintenance and guarantee capability to a severe test. To accurately grasp the civil-military integration of aviation maintenance and guarantee capabilities, it is necessary to evaluate their capabilities. To this end, the evaluation indicator system is established by using the three-dimensional indicator system construction model of "maintenance task → task demand → capability demand", and the evaluation method based on intuitionistic fuzzy entropy and normal grey cloud model is proposed, using intuitionistic fuzzy entropy theory to determine the expert weights and indicator weights, and the grey cloud model theory to determine the capability evaluation level. Finally, the application process of the evaluation model is demonstrated through specific examples, and the evaluation results are analyzed to verify the effectiveness of the evaluation model.

In this paper, a semi-empirical model of air waves induced by falling rock is described. The model is composed of a uniform motion phase (velocity close to 0 m·s^-1) and an acceleration movement phase. The uniform motion phase was determined based on experimentally and the acceleration movement phase was derived by theoretical analysis. A series of experiments were performed to verify the semi-empirical model and elucidated the law of the uniform motion phase. The acceleration movement phase accounted for a larger portion with a greater height of the falling rock. Experimental results of different falling heights of the goaf showed close agreement with theoretical analysis values. The semi-empirical model could accurately and conveniently estimate the velocity of air wave induced by falling rock. Thus, the semi-empirical model can provide a reference and basis for estimating the speed of air waves and designing protective measures in mines.

In this article, we introduce some multi-messenger studies of blazars. Main contents contain the following parts, 1. the subclasses of blazars and the observational characteristics, 2. emission variabilities from the multi-messenger observations, 3. the physical origin for the multi-messenger studies. Based on mid-IR observations collected from the $WISE$ database, we collect two sources (BZQ J1700+6830 and BZQ J1842+6809) to analyze the mid-IR variabilities. \\ (1) For BZQ J1700+6830, the period is $P\approx$ 42 hr at the four bands ($W1$, $W2$, $W3$, $W4$); for BZQ J1842+6809, the period is $P\approx$ 123 hr at the two bands ($W1$, $W2$). \\ (2) Using the periodicities, we calculate that the central black hole mass ($BH$) should be $M = (5.44\sim33.0)\times10^8M_{\odot}$ for BZQ J1700+6830 and $M = (1.13\sim6.88)\times10^9M_{\odot}$ for BZQ J1842+6809.\\ (3) For the two sources, during the flaring stage, we find anti-clockwise variation trends based on the time-based relations built by the spectral indices ($\alpha$) and flux densities ($F$).\\ (4) We calculate the Doppler factor ($\delta$) when the sources are in the dimming or brightening stages, and find that with the frequency increasing, the Doppler factor become stronger.

MEMS (Micro-electromechanical Systems) becomes important increasingly due to the smarter and smaller fuze used in OICW (Objective Individual Combat Weapon). MEMS Safety and Arming (S&A) device is employed in different platforms and regions for small caliber projectile. Therefore, it is necessary to make a parametric study of the MEMS S&A device in different apply environments and explore the main sensitive factors of the MEMS S&A device to provide reference for designs. In this paper, based on the MEMS S&A device designed by our term, theory and finite element models are established, and the centrifugal insurance mechanism of the MEMS S&A device is parametric studied under the different speeds, temperature and thickness of the model by nonlinear dynamic method. By comparing the experimental and predicted results, the established FEM model is verified, and the conclusion is that the temperature and the centrifugal force are the main sensitive factors in the centrifugal insurance mechanism. In summary, we can suggest that the application environment, which the MEMS S&A device is suitable for, is the temperature equal to or slightly greater than normal temperature and the rotating speed higher than35000r/min of small caliber projectile.

Territory space is an ecological resource carrier and place for human development. Human activities and ecological systems are the basis of ecological product supply. Promoting territory spatial protection and governance by improving the ecological products supply is very important. In this study, we established an ecological products supply capacity evaluation index system involving three types of ecological products, i.e., ecological environmental products, ecological material products, and ecological cultural products. For the case of the Beijing-Tianjin-Hebei region, we comprehensively used principal component analysis, equivalent factor method, and entropy method to evaluate the supply capacity of the ecological products from 2011 to 2021. Then, we analyzed the spatio-temporal pattern combining the natural breakpoint and quantile classification methods and analyzed the obstacle factors using the obstacle degree model of ecological supply. The results show that the supply capacity of different ecological product in each city are closely related to ecological resource endowment. The supply capacity of ecological products exhibited an upward trend, with the highest ecological environmental products supply, relatively smaller ecological material product supply, and the largest growth rate for ecological cultural product supply. The supply capacity of different ecological products varied across cities over time and displayed noticeable spatial differentiation. The main obstacle factors included eco-land, eco-tourism, eco-leisure, park green space, and fishery products, although there were variations among cities. Finally, based on the level, spatial-temporal pattern, and obstacle factors of ecological product supply, we proposed strategies for territory spatial protection and governance from the perspectives of integrated protection of elements, structural regulation, and systematic governance. The results reflected the ecological functional heterogeneity of territory space, which can provide spatial planning guidance for sustainable development.

Global warming poses a threat to plant survival, impacting growth and agricultural yield. Protein turnover, a critical regulatory mechanism balancing protein synthesis and degradation, is crucial for cellular response to environmental changes. We investigated the effects of elevated temperature on proteome dynamics in Arabidopsis thaliana seedlings using 15N-stable isotope labeling and ul-tra-performance liquid chromatography-high resolution mass spectrometry, coupled with the ProteinTurnover algorithm. Analyzing different cellular fractions from plants grown under 22°C and 30°C growth conditions, we found significant changes in the turnover rates of 571 proteins, with a median 1.4-fold increase, indicating accelerated protein dynamics under thermal stress. Notably, soluble root fraction proteins exhibited smaller turnover changes, suggesting tissue-specific adap-tations. Significant turnover alterations occurred with redox signaling, stress response, protein folding, secondary metabolism, and photorespiration, indicating complex responses enhancing plant thermal resilience. Conversely, proteins involved in carbohydrate metabolism and mito-chondrial ATP synthesis showed minimal changes, highlighting their stability. This analysis high-lights the intricate balance between proteome stability and adaptability, advancing our under-standing of plant responses to heat stress and supporting the development of improved thermo-tolerant crops.

Since sensor-based perception systems are used in autonomous vehicle applications, validating such systems is imperative to guarantee the robustness of the systems before they are being put to use. In this study, a comprehensive corruption-related simulation-based robustness verification and enhancement process for sensor-based perception systems is proposed. Firstly, we present a methodology and scenario-based corruption generation tools for creating diverse simulated test scenarios that can analogously represent real-world traffic environments, especially considering corruption types related to safety concern. Then, an effective corruption similarity filtering algorithm is proposed to remove corruption types with high similarity and identify the representative corruption types to represent all considered corruption types. As a result, we can generate efficient corruption-related robustness test scenarios with less testing time and good scenario coverage. Subsequently, we perform the vulnerability analysis of object detection models to identify model weaknesses and construct an effective training dataset for model vulnerability enhancement. This enhances the tolerance of object detection models to weather and noise-related corruptions, ultimately improving the robustness of the perception system. We employ case studies to demonstrate the feasibility and effectiveness of the proposed robustness verification and enhancement procedures. Additionally, we explore the impact of different "similarity overlap threshold" parameter settings on scenario coverage, effectiveness, scenario complexity (size of training and testing datasets), and time costs.

This research used an experimental study design in which 60 subjects were randomly assigned to either an experimental (image e-book guidance) group or a control (text guidance) group after meeting the admission conditions and agreeing to participate in the study. It was proven that providing image e-book guidance before surgery significantly changed the behavior of patients and promoted relief of urinary catheter discomfort through self-efficacy to reduce urinary catheter pain after surgery. It was found that providing image e-book guidance can shorten the time for health education and provide patients with repeated medical education and familiarity with health guidance, which can help to address the important clinical service demand issue and the shortage of nursing staff.

A digital text abstract presents the essential information of an article, and we can find the trend and value of the research by analyzing it rigorously and digging up knowledge. Therefore, this study focuses on the abstracts of index journals in China and Taiwan from July 2010 to June 2020 (a total of 3,283 abstracts). Through the concepts of text mining and natural language processing (NLP), it constructs processes such as text retrieval, text segmentation and word cloud analysis, TF-IDF weight analysis, co-word analysis, network analysis, and trend analysis, and analyses a large amount of text data. The results show that the scope of research in China covers the fields of social sports and sports science, and research in Taiwan covers both natural and social sciences. The network diagram highlights the richness of sports-related research fields in the two regions, but research on sports philosophy is relatively rare. It is suggested that all disci-plines/departments should re-allocate the same resources, so as to show a balanced development trend and help expand a new chapter in the sports academic field.

To compare The effects of organic and inorganic impregnation on the properties of unmodified, phenol formaldehyde oligomer-modified (PFOMCF), and sodium silicate-modified Chinese fir wood (SSMCF) were compared using samples prepared using the respiratory impregnation method. Impregnation and reinforcement effects and water resistance of PFOMCF and SSMCF were compared and the results was showed that the weight percentage gain, density increase rate, bending strength, and compressive strength of SSMCF were clearly higher than those of PFOMCF and had a lower water absorption rate within 60 h. The impregnation and reinforcement effects and dimensional stability of SSMCF were better than those of PFOMCF. FT-IR, XRD, CONE, and TGA examinations were used to test and analyze the chemical structure, crystalline structure, flame retardancy, and heat resistance of these modified woods. The results indicated that SSMCF possessed more hydrogen bonds than PFOMCF and that Si–O–Si chemical bonding with high bond energy was formed. Meanwhile, the weakened degree of the diffraction peak of SSMCF was much less than that of PFOMCF. These results explained that the mechanical properties and water resistance of SSMCF were better than PFOMCF. Compared with PFOMCF, SSMCF had a lower heat release rate (HRR), peak-HRR, mean-HRR, total heat release, smoke production rate, and total smoke production as well as higher thermal decomposition temperature and residual rate. Inorganic sodium silicate was shown to be a better flame retardant, while SSMCF had good smoke suppression effects, thermal stability, and safety performance in the case of fire.

Salvia hispanica (chia) is a highly nutritious food source and has gained popularity due to its high omega-3 fatty acid content. Red spider mites are a serious problem in the production of S. hispanica. However, no study has been conducted to analyse the defensive response to the infestation of red spider mites in S. hispanica. To elucidate the molecular mechanisms of the defensive response of S. hispanica to red spider mites, we performed a transcriptomic analysis of S. hispanica when infested by red spider mites. In the comparative assessment of leaf transcriptomes, a total of 1743 differentially expressed genes (DEGs) were identified between control and mite-infested S. hispanica. From these, 1208 (69%) transcripts were up-regulated and 535 (31%) were down-regulated. The DEGs included transcription factors, defense hormones, and secondary metabolites that were either suppressed or activated in response to spider mite herbivory. Gene Ontology (GO) enrichment analysis revealed that plant secondary metabolites such as glucosinolates, and signalling pathways, including the jasmonic acid signalling pathway, may play an important role in the defence against red spider mites. This study provides novel insights into the defence response of S. hispanica in response to insect herbivory and could be a resource for the improvement of pest resistance in the chia.

High-dimensional measurement error data are becoming more prevalent across various fields. Research on measurement error regression models has gained increasing attention due to the risk of drawing inaccurate conclusions if measurement errors are ignored. When the dimension p is larger than the sample size n, it is challenging to develop statistical inference methods for high-dimensional measurement error regression models due to the existence of bias, nonconvexity of objective function, high computational cost and many other difficulties. Over the past few years, some works have overcome the aforementioned difficulties and proposed several statistical inference methods. This paper mainly reviews the current development on estimation, hypothesis testing and variable screening methods for high-dimensional measurement error regression models and shows the theoretical results of these methods with some directions worthy of exploring for future research.

Version Control and Source Code Management Systems, such as GitHub, contain large amount ofunstructured historical information of software projects. Recent studies have introduced Natural Language Processing (NLP) to help software engineers retrieve information from very large collection of unstructured data. In this study, we have extended our previous study by increasing our datasets and ML and clustering techniques. Method: We have followed a complex methodology made up of various steps. Starting from the raw commit messages we have employed NLP techniques to build a structured database. We have extracted their main features and used as input of different clustering algorithms. Once labelled each entry, we have applied supervised machine learning techniques to build a prediction and classification model. Results: We have developed a machine learning-based model to automatically classify commit messages of a software project. Our model exploits a ground-truth dataset which includes commit messages obtained from various GitHub projects belonging to the HEP context. Conclusions: The contribution of this paper is two-fold: it proposes a ground-truth database; it provides a machine learning prediction model. They automatically identify the more change-proneness areas of code. Our model has obtained a very high average precision, recall and F1-score.

Service pricing is a bottleneck in the development of innovation services, as it is the issue of most concern between the suppliers and demanders. In this paper, a negotiation pricing model that is based on the multiobjective genetic algorithm is developed for innovation service pricing. Regarding the service pricing process as a multiobjective problem, the objective functions, which include the service price, service efficiency, and service quality, for suppliers and demanders are constructed. As the solution of a multiobjective problem is typically a series of alternatives, another negotiation process is necessary for determining the final decision. A learning strategy is adopted during the negotiation process to simulate reality. Finally, the model is implemented for an innovation service transaction, the objective of which is to identify the optimal price plan. The results demonstrate that the model can provide quantitative decision support for the pricing of an innovation service and ultimately yield a win-win result for both the supplier and demander of the innovation service. Furthermore, the influence of the parameters during the negotiation process is analyzed in detail. The effects of the learning strategy on accelerating the negotiation process, as well as the chosen of reasonable parameters are given.

The rapid development of 2019-2020 Wuhan seafood market pneumonia currently posed a major public health concern in China. Genome sequencing identified a novel beta-coronavirus closely related to SARS-CoV, named 2019-nCoV by WHO, as the cause of this pandemic disease. Viruses with single stranded RNA genome are prone to evolve quickly by accumulation of mutations, such as SNV, INDEL and cross viral recombination, aiding fast transmission among hosts and cross species. Here we collected related genome sequences and investigated variations shared by different strains of 2019-nCoV, identified reoccurrence of SNV mutations in clusters of patients, an indication of rapid evolution of 2019-nCoV at the transmission from animal host to human. The information collected herein would help to understand the dynamics of current pandemic.

Thought runs through the mind like blood runs through our body to keep us alive. Like the mind, the body does not stay inert and is in constant motion. Not a single cell in our body is left inert unless cell is under stress or dying. These scenarios are reflected upon when a person is sick, the person lies in bed with less movement; however, is active when the person is healthy. The topic of mechanical stimulation has emerged due to the increasing understanding of the physical stimulations we face each day. Further understanding of the mechanically-regulated mechanism can help us explore the pathological events in a disease. Here, we reviewed the role of sensory proteins in pathological events that are observed in cardiomyopathy, cancer, respiratory, renal, obesity, genetics, physical injury and bacterial infection. Taken together, sensory proteins are mechanically-activated which assist reception of external physical stimulation and convert into biochemical to trigger intracellular signaling cascade.

The scope of this work was part of our previous research on Pulsed Power Plasma Stimulation Technique. Electromagnetic fields generated during a pulsed power plasma discharge were simulated using a finite element method in the COMSOL RF module. The field distributions were calculated during and after the pulse. The current paper takes advantage of prior work measuring and modeling the current distribution in the plasma arc. Agreement with laboratory experimental measurements provides support for extension of the model to reservoir scale. The validated model was used to quantify the signal attenuation level in different medium environment.

Bacteria and archaea participate in and are influenced by processes of substance circulation and energy exchanges in natural environment. Generally, the community changes of bacteria and archaea in sediment are mainly driven by seasonality in mid-latitude regions. But in our study, water diversion to Fen river played a more important role on OTU number, diversity and community structure of bacteria and archaea in sediment than seasonal variation, which was found by 16S rRNA high-throughput sequencing technology. This phenomenon might be caused by external transferred water on the physicochemical water environment and accelerated release of positive nitrogen from sediment caused by rise of water level. Changes of carbon-nitrogen cycle and increase of electrical conductivity (EC) value induced more diversion-responders than season-responders both for bacteria and archaea. Seasonal changes have been influencing bacteria and archaea mildly throughout the whole study reach. After water diversion, the environment indicators relating to bacteria community obviously changed from nutrients to salinity while that for archaea almost disappeared. Our research showed the effects of human activities on the communities of bacteria and archaea outweigh the forcing from natural seasonal changes in mid-latitude regions and revealed the mechanism, highlighting different responses of bacteria and archaea to environmental changes.

Precise individual tree or sample-based inventories derived from 3D point cloud data of mobile laser scanning can improve our comprehensive understanding of the structure, function, resilience, biodiversity, and ecosystem services of urban forests. This study assessed the performance of a hand-held laser scanning system for the extraction of tree position, diameter at breast height (DBH) and tree height (H) in an urban area. A total of 2083 trees of 13 species from 34 plots were analyzed. The results showed that the registration of tree positions using ground control points (GCPs) demonstrated high accuracy, with errors consistently below 0.4 m, except for a few instances. The extraction accuracy of DBH for all trees and individual species remained consistently high, with a total root mean square error (RMSE) of 2.06 cm (6.89%) and a bias of 0.62 cm (2.07%). Notably, broad-leaved trees outperformed coniferous trees, with RMSE and bias values of 1.86 cm (6%) and 0.76 cm (2.46%) compared to 2.54 cm (9.46%) and 0.23 cm (0.84%). Tree height extraction accuracy varied significantly among different species, with R2 values ranging from 0.65 to 0.92. Generally, both DBH and height were underestimated. Linear mixed effects models (LME) were applied to evaluate factors affecting the performance of HLS with the plot as a random factor. LME analysis revealed that plant type and terrain significantly influenced the accuracy of DBH and H derived from HLS data. Other fixed factors of plot area, tree density and trajectory length didn’t have significance. With a large sample size, we concluded that the HLS demonstrated sufficient accuracy in extracting individual tree parameters in urban forests.

Despite the strong anticancer activity of SN38 (7-ethyl-10-hydroxy-camptothecin), some defects prevent its clinical application, such as severe side effects and loss of anticancer activity due to lack of selectivity to cancer cells and hydrolysis of ring E, respectively. To address the issue, herein a multifunctional SN38 derivative (compound 9) containing biotin (tumor-targeting group) and valproic acid (histone deacetylase inhibitor, HDACi) was synthesized via click chemistry and evaluated using MTT assay. The in vitro cytotoxicity study showed that compound 9 exhibited superior cytotoxicity as irinotecan against human cervical cancer HeLa cells, albeit inferior to SN38. More significantly, compound 9 significantly reduced toxicity in mouse embryonic fibroblast NIH3T3 cells, indicating that compound 9 had the capacity to enhance tumor targeting due to its cell selectivity. Further studies demonstrated that compared with irinotecan, compound 9 induced similar apoptosis of cancer cells. Consequently, compound 9 can not only improve its tumor-targeting ability mediated by biotin but also exert the potent anticancer activity through the synergism of SN38 and valproic acid, indicating that the design concept is an effective strategy for structural modification of SN38.

In the paper, we develop some numerical schemes including finite difference scheme and finite volume scheme for the fractional Laplacian operator, and apply the resulted numerical schemes to solve some fractional diffusion equations. First, the fractional Laplacian operator can be characterized as the weak singular integral by a integral operator with zero boundary condition. Second, because of the solution of fractional diffusion equation is usually singular near the boundary, we apply finite difference scheme to discrete fractional Laplacian operator and fractional diffusion equation by fractional interpolation function. Moreover, it is find that the differential matrix of the above scheme is symmetric matrix, and strictly row-wise diagonally dominant in special fractional interpolation function. Third, we show finite volume scheme to discrete fractional diffusion equation by fractional interpolation function, and analyze the properties of differential matrix. Finally, the numerical experiments are given, and verify the correctness of theoretical results and the efficiency of the schemes.

Aspergillus montevidensis is an important domesticated fungus that has been applied to produce many traditional fermented foods under high osmotic conditions. However, the detailed mechanisms of tolerance to osmotic stress remain largely unknown. Here, we construct a target-deleted strain (ΔLeuRS) of A. montevidensis and found that the ΔLeuRS mutants grew slowly and suppressed the development of the cleistothecium compared to the wide-type strains (WT) under salt-stressed conditions. Furthermore, differentially expressed genes (P<0.0001) governed by LeuRS were involved in salt tolerance, ABC transporter, amino acid metabolism, sugar metabolism, and reproduction process. The ΔLeuRS strains compared to WT strains under short- and long-term salinity stress especially altered accumulation levels of metabolites, such as amino acids and derivatives, carbohydrates, organic acids, and fatty acids. The study provides new insights into the underlying mechanisms of salinity tolerance and lays a foundation for favor improvement of foods fermented with A. montevidensis.

Molecular communication (MC) is a promising bio-inspired paradigm for exchanging molecule information among nanomachines. This paper proposes a synchronisation-assist photolysis MC system that aims to transmit the bio-sensing signal of the tumour microenvironment, facilitated by mitigating redundant molecules for improved bit error rate (BER) performance. Benefits from bio-compatible MC, biosensors could transmit bio-sensing signals of the tumour in $vivo$ instead of converting them to electrical signals. Due to diffusion motion's slow and stochastic nature, inter-symbol interference (ISI), resulting from previous symbols' residual information molecules, inevitably occurs in diffusion-based MC. ISI is one of the challenges in diffusion-based MC, which significantly impacts signal detection. Inspired by on-off keying (OOK) modulation, the proposed modulation implements a switch of molecules and light alternatively. The light emitted is triggered by a synchronisation signal, and the photolysis reactions could reduce the redundant molecules. An expression for the relevant channel impulse response (CIR) is derived from a hybrid channel model of diffusion and photolysis-reaction. This paper implements the maximum posterior estimation scheme to find the optimal decision threshold and analysis the BER performance in terms of different time intervals of the system. Numerical simulations demonstrate that the proposed method can improve the channel capacity and BER performance. We believe that our work may pave the way for MC application in bio-sensing.

Plastic flow in body-centered cubic (bcc) alloys is governed by the thermally-activated screw dislocation motion. In bcc interstitial solid solutions, solute diffusion can occur at very fast rates owing to low migration energies and solute concentrations. Under mechanical loading, solutes may move on the same or similar time scale as dislocations glide, even at low temperatures, potentially resulting in very rich co-evolution processes that may have important effects in the overall material response. It is therefore important to accurately quantify the coupling between interstitial impurities and dislocations, so that larger-scale models can correctly account for their (co)evolution. In this paper, we use electronic structure calculations to obtain the energetics of oxygen diffusion under stress and its interaction energy with screw dislocation cores in bcc tungsten. We find that oxygen atoms preferentially migrate from tetrahedral to tetrahedral sites with an energy of 0.2 eV. This energy couples only weakly to hydrostatic and deviatoric deformations, with activation volumes of less than $0.02$ and $0.2b^3$, respectively. The strongest effect is found for the inelastic interaction between O atoms and screw dislocation cores, which leads to attractive energies on the order of 1.5 eV and a structural transformation of the screw dislocation core from an `easy' to a `hard' core configuration

Tea (Camellia sinenesis) is a health beneficial beverage and is also a source for extracting bioactive components such as theanine, tea polyphenols (TPP) and tea polysaccharides (TPS). TPS is a group of hetero-polysaccharides bounded with proteins. There were tests showing that TPS had various bioactivities, such as antioxidant, antitumors, antihyperglycemia, anti-inflammation and improving immunity. However, inconsistent results concerning chemical composition and bioactivity of TPS were published in recent years. The advances in chemical composition and bioactivities of TPS were reviewed in the present paper. The inconsistent and controversial results regarding composition and bioactivities of TPS were also discussed.

ALDH+ H1975 lung adenocarcinoma stem cells (LSCs) are a rare cell population identified in lung adenocarcinoma (LUAD). LSCs can self-renew, drive tumor initiation, growth, metastasis, and recurrence, and are also the predominant cause of poor prognosis due to their intrinsic resistance to drugs and chemotherapy. Consequently, LSCs are a promising target for LUAD therapy. Noncoding RNAs (ncRNAs), including microRNAs (miRNAs), long noncoding RNAs (lncRNAs), and circular RNAs (circRNAs), exert many significant regulatory functions in the pathogenesis of human cancers, showing the necessity for a comprehensive understanding of the mechanisms that underlie lung carcinogenesis. Nonetheless, research on many known transcripts and messenger RNAs (mRNAs) has already generated new information. Unknown biomarkers in ncRNAs and systematic and comprehensive interrelation with unknown ncRNAs and mRNAs may provide further insights into the biology of LUAD. Herein, a set of novel ncRNAs that include miRNAs, lncRNAs, circRNAs, were identified and differentially expressed patterns of ncRNAs and mRNAs in LSCs and ALDH- H1975 LUAD tumor cells (LTCs) were obtained using stringent bioinformatics pipelines. Through a meta-analysis of the identified landscapes, novel competitive endogenous RNA (ceRNA) networks were constructed to reveal the potential molecular mechanisms that regulate the hallmarks of LSCs and LTCs. This study presents a summary of novel ncRNAs and the fundamental roles of differentially expressed ncRNAs implicated in the activity of LSCs and LTCs. In addition, the study also provides a comprehensive resource for the future identification of diagnostic, therapeutic, and prognostic biomarkers in LUAD.

Chemotherapy treatment based on Cisplatin (CDDP) is established as the drug of choice for head and neck squamous cell carcinoma (HNSCC). Malignant tumors respond to microenvironment alteration through a dynamic balance of mitochondrial fission and fusion. HNSCC is known to have hypoxic conditions, yet the effects and underlying mechanisms of hypoxia on chemosensitivity and mitochondrial dynamics remain unclear. We found that hypoxia promoted mitochondrial fission and CDDP sensitivity in HNSCC cells. Importantly, Mff was shown to be correlated with chemosensitivity in clinical samples of HNSCC that underwent a hypoxic condition. Hypoxia-inducible factor 1 α-subunit (HIF-1α) dramatically increased Mff transcriptional expression and directly bound to Mff. Hypoxia enhanced the release of reactive oxygen species (ROS) and upregulated the expression of Mff via HIF-1α in HNSCC cells. ROS depletion in HNSCC cells attenuated HIF-1α, Mff expression, and mitochondrial fission. Moreover, a knockdown of Mff suppressed hypoxia-induced mitochondrial fission and decreased CDDP chemosensitivity in vivo and in vitro. Our findings revealed that the hypoxia-induced release of ROS promoted mitochondrial fission and CDDP chemosensitivity via the regulation of HIF-1α/Mff in HNSCC cells, indicating that Mff may serve as a new biomarker to predict neoadjuvant chemosensitivity in HNSCC patients

A one-pot, one-step protocol combining hydrogen transfer initiated dehydration (HTID) of 1,3-propanediol (1,3-PDO), catalysed by [Cp*IrCl2(NHC)] (Cp* = pentamethylcyclopentadienyl; NHC = carbene ligand) complexes (1-5H and 1-3F), and self-aldol condensation (SAC) of propanal (2), allowed selective production of aldehyde 2-methyl-pent-2-enal (3), in ionic liquids with high substrate conversion. The Ir(III) pre-catalysts, and the ionic liquids, were recyclable. 3 could also be selectively produced in the presence of water, and in neat 1,3-PDO. The efficient, selective delivery of a value-added chemical from 1,3-PDO, a major product of many whole cell bacterial fermentation processes, shows that the combination of chemo-catalytic processing of the chemical platform via Cp*IrCl2(NHC) - catalysed HTID / SAC with bio-catalysis has the potential to allow direct valorisation of the bio-renewable feedstocks, such as waste glycerol and sugars, into valuable chemicals.